aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link TL-WR941N/ND v2/v3Chuanhong Guo2018-08-144-0/+184
| | | | | | | | | | | | | Specification: - SoC: Atheros AR9132 - Flash: 4 MB - RAM: 32 MB - Ethernet: Marvell 88E6060 with 5 FE ports. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for TP-Link WR841N/ND v11Johann Neuhauser2018-08-143-1/+42
| | | | | | | | | | | | | | Specification: - SoC: Atheros AR9533 - Flash: 4 MB - RAM: 32 MB - Ethernet: 4x LAN (100M) / 1x WAN (100M) - WiFi: 2.4G 300M Flash instruction: Flash factory image from stock WebUI. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: move TP-Link WR841v9 aliases node from dtsi to dtsJohann Neuhauser2018-08-142-5/+5
| | | | | | | | Move the alias node of the TP-Link WR841v9 and rename the phandle of the qss led to qss_led in preparation for adding the very similar TP-Link WR841v11. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: fix sysupgrade TP-Link WR841v9Johann Neuhauser2018-08-142-2/+1
| | | | | | | Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and for consistency rename everything to tl-wr841-v9. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* firmware-utils/mksercommfw: fix build with clang/macOSRyan Mounce2018-08-141-1/+1
| | | | | | | | fixes error: non-void function 'main' should return a value Fixes: FS#1770 Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ath79: Add wifi to WNDR3700, WNDR3700v2 and WNDR3800Hannu Nyman2018-08-144-1/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath9k wifi capabilities to WNDR3700 family. * use kmod-owl-loader to load firmware from "art" * add wifi to DTS * add wifi LEDs Avoid using the same MAC for eth0 LAN and wlan0 by toggling the eth0 MAC into a locally administered MAC. That is currently done by in user-space by adding a uci config item into /etc/config/network (More elegant solution might be setting it already in preinit phase.) Known issues: * wifi firmware file may not get created on the first boot after flashing on time to bring wifi normally up. Likely the overlay jffs2 is not yet ready for creating the firmware file. "wifi up" may still bring wifi up. Wifi will work normally at subsequent boots. * phy0 and phy1 may get assigned mixed, so that phy0 may be the 5GHz radio instead of the normal 2.4GHz, and vice versa for phy1. Does not happen always, but may happen. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [fix the wifi unit address in the dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Pisen WMM003N (Cloud Easy Power)Icenowy Zheng2018-08-143-0/+136
| | | | | | | | | | | | | | | | | | | | | Pisen WMM003N (sold under the name of Cloud Easy Power) is an AR9331-based router and power bank combo device. The device uses a stock firmware modified from OpenWRT for TP-Link TL-WR703N; however some GPIO definition is different on this device with TL-WR703N. An AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also added, and the stock Flash/RAM configuration is 8MiB/64MiB. The stock firmware is an old and heavily modified OpenWRT-based firmware, which has telnetd defaultly open, and the root password is "ifconfig" (quotation marks not included). The factory image format is not known yet, however the stock firmware ships the OpenWRT's sysupgrade command, and it can be used to install a newer firmware. Due to the lack of the access to the STM8 embedded controller, the SD slot is currently not usable (because it's muxed with the on-board USB port) and the AXP PMIC cannot be monitored. Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* firewall: bump to git HEADStijn Tintel2018-08-131-3/+3
| | | | | | | | 12a7cf9 Add support for DSCP matches and target 06fa692 defaults: use a generic check_kmod() function 1c4d5bc defaults: fix check_kmod() function Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar7: remove linux 3.18 supportKoen Vandeputte2018-08-1314-998/+0
| | | | | | | This target is on 4.9 currently. It seems the support for this old kernel never got dropped. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* firmware-utils/mksercommfw: fix musl buildAndy Walsh2018-08-131-0/+1
| | | | | | * add missing <sys/types.h> for musl Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
* ramips: add missing USB packages into ASL26555-16MZoltan HERPAI2018-08-131-1/+1
| | | | | | | Mirror the package list from the 8M device profile to the 16M device profile. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* tools/cmake: Update to 3.12.1Daniel Engberg2018-08-132-3/+3
| | | | | | Update cmake to 3.12.1 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ath79: drop tl prefix for TP-Link RE450 v2Peter Lundkvist2018-08-132-2/+2
| | | | | | | | This router is called RE450 and the tl prefix was used to identify it as a TP-Link device. Drop the tl prefix since we now have tplink in dts and device name. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* ath79: gmac: add parsers for rxd(v)- and tx(d|en)-delay for AR9344Christian Lamparter2018-08-132-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some AR9344 boards do very poorly with the default settings and need custom rxdv-delay, rxd-delay, txd-delay, txen-delay flags to perform reasonably. In this case the WD My Net Wi-Fi Range Extender can not even manage 10Mbps on a 1Gbit link: root@AR9344:~# iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from client [...] [ 5] local [...] connected to client [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 1.09 MBytes 9.16 Mbits/sec [ 5] 1.00-2.00 sec 895 KBytes 7.33 Mbits/sec [ 5] 2.00-3.00 sec 762 KBytes 6.25 Mbits/sec [...] [ 5] 10.00-10.03 sec 17.0 KBytes 4.74 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.03 sec 9.00 MBytes 7.52 Mbits/sec with but with the correct settings in place, it does much better: root@AR9344:~# iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from client [...] [ 5] local [...] connected to client [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 23.1 MBytes 193 Mbits/sec [ 5] 1.00-2.00 sec 23.1 MBytes 194 Mbits/sec [ 5] 2.00-3.00 sec 23.2 MBytes 195 Mbits/sec [...] [ 5] 10.00-10.04 sec 710 KBytes 180 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.04 sec 237 MBytes 198 Mbits/sec The tx data and enable delay bits definitions are taken from Atheros' AR9344 Data Sheet Section "8.6.1 Ethernet Configuration (ETH_CFG)" on page 153. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* packages: nvram: make it possible to include it for ath79 targetsChristian Lamparter2018-08-131-1/+1
| | | | | | | | | The WD My Net Range Extender stores the MAC addresses inside the nvram partition. This utility can extract it, but it's currently not avilable on the ath79 target. Hence, this patch adds the necessary target declaration, so it can be built. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* uboot-zynq: update to 2018.07Luis Araneda2018-08-133-3/+46
| | | | Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ath79: add QCA956x GMAC configDavid Bauer2018-08-132-0/+18
| | | | | | This commit adds the ability to configure the GMAC of the QCA956x. Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm47xx: cosmetic fix in model detectionPaul Wassi2018-08-131-1/+1
| | | | | | | | In "brcm47xx: rework model detection" the file 01_detect was moved to 01_network, therefore also update the warning message in case everything fails. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: ar913x: fix eth pll registerChuanhong Guo2018-08-131-1/+1
| | | | | | | PLL for eth0 internal clock on ar913x is at 0x18050014 and AR913X_ETH0_PLL_SHIFT is 20 instead of 17 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: fix speed applied to MII0/1_CTRL on ar71xx/ar913xChuanhong Guo2018-08-131-2/+2
| | | | | | Currently speed value is applied to interface mode field. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add WNDR3700 and WNDR3700v2Hannu Nyman2018-08-134-0/+93
| | | | | | | | | | | | Add support for WNDR3700 and WNDR3700v2. They share most things with WNDR3800. Only device IDs and partition structure needs to be set. Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has also the NA version of the factory image. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: create WNDR3700 series .dtsi and adjust WNDR3800Hannu Nyman2018-08-133-200/+212
| | | | | | | | | | | | | | | | | Prepare for addition of WNDR3700 and WNDR3700v2 by separating the common parts into wndr3700.dtsi and leaving just the device-specific things into wndr3800.dts The three routers are identical except * device IDs * WNDR3700 (v1) has only 8 MB flash, while others have 16 MB. Partition structure needs to be defined for each device. * (WNDR3800 has 128 MB RAM, but RAM size is not in DTS) Also separate the common parts of the image recipe. (Drop also the initramfs recipe.) Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ramips: fix BR-6478ACv2 supportDaniel Gimpelevich2018-08-136-70/+61
| | | | | | | | | | | | | | | | | The wholesale changes introduced in commit f9b8328 missed this DTS file because it hadn't been merged yet. This patch brings it in line to match the other mt7620a devices' DTS files. Additionally, the Internet LED is now labeled correctly and set to unused by default, since the WAN interface is not known in every configuration. Using sysupgrade between images before and after this commit will require the -F flag. Tested-by: Rohan Murch <rohan.murch@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [drop internet led default setting] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Netgear R6120Ludwig Thomeczek2018-08-135-0/+180
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6120, aka Netgear AC1200. Specification: - SoC: MediaTek MT7628 (580 MHz) - Flash: 16 MiB - RAM: 64 MiB - Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E) - LAN speed: 10/100 - LAN ports: 4 - WAN speed: 10/100 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 To flash use nmrpflash with the provided factory.img. Flashing via webinterface will not work, for now. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* firmware-utils: add sercomm/netgear toolLudwig Thomeczek2018-08-133-0/+265
| | | | | | | | | | | This adds a tool to generate a firmware file accepted by Netgear or sercomm devices. They use a zip-packed rootfs with header and a custom checksum. The generated Image can be flashed via the nmrpflash tool or the webinterface of the router. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* wireguard: bump to 0.0.20180809Jason A. Donenfeld2018-08-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * send: switch handshake stamp to an atomic Rather than abusing the handshake lock, we're much better off just using a boring atomic64 for this. It's simpler and performs better. Also, while we're at it, we set the handshake stamp both before and after the calculations, in case the calculations block for a really long time waiting for the RNG to initialize. * compat: better atomic acquire/release backport This should fix compilation and correctness on several platforms. * crypto: move simd context to specific type This was a suggestion from Andy Lutomirski on LKML. * chacha20poly1305: selftest: use arrays for test vectors We no longer have lines so long that they're rejected by SMTP servers. * qemu: add easy git harness This makes it a bit easier to use our qemu harness for testing our mainline integration tree. * curve25519-x86_64: avoid use of r12 This causes problems with RAP and KERNEXEC for PaX, as r12 is a reserved register. * chacha20: use memmove in case buffers overlap A small correctness fix that we never actually hit in WireGuard but is important especially for moving this into a general purpose library. * curve25519-hacl64: simplify u64_eq_mask * curve25519-hacl64: correct u64_gte_mask Two bitmath fixes from Samuel, which come complete with a z3 script proving their correctness. * timers: include header in right file This fixes compilation in some environments. * netlink: don't start over iteration on multipart non-first allowedips Matt Layher found a bug where a netlink dump of peers would never terminate in some circumstances, causing wg(8) to keep trying forever. We now have a fix as well as a unit test to mitigate this, and we'll be looking to create a fuzzer out of Matt's nice library. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* at91: do not build image for at91-q5xr5Hauke Mehrtens2018-08-121-1/+1
| | | | | | | | The kernel image of the at91-q5xr5 is getting too bing now and this is breaking the build. Remove the image for the at91-q5xr5 from the build to at least build images for the other devices. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: fix eth pll for ar913xChuanhong Guo2018-08-111-1/+1
| | | | | | PLL node is missing syscon in compatible string. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for I-O DATA WN-AC1600DGR2INAGAKI Hiroshi2018-08-117-9/+257
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM - 16 MB of Flash - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR2 2. Connect power cable to WN-AC1600DGR2 and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support of D-Link DIR-825 B1Dmitry Tunin2018-08-114-0/+288
| | | | | | Add support for the ar71xx supported D-Link DIR-825 B1 to ath79. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add ath9k calibration data MAC addresses patchingChristian Lamparter2018-08-111-0/+50
| | | | | | | | | | | | | | | | | | This patch copies over the MAC patching helper functions from lantiq's target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom file. Not all vendors bothered to write the correct MAC addresses for the ath9k wifi into the calibration data. And while ath9k does have some special dt-properties to extract the addresses from a fixed position, there are still devices that require userspace to edit or modify the caldata. In my case, the MAC address for the Wi-Fi device is stored in an unsorted key-value based "nvram" database and there's an existing userspace tool to extract the data. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* base-files: add function to get mac as text from flashMathias Kresin2018-08-111-0/+23
| | | | | | | | | Add a function to get a mac stored as text from flash. The octets of the mac address need to be separated by any separator supported by macaddr_canonicalize(). Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: use consistent coding styleMathias Kresin2018-08-111-8/+4
| | | | | | | | Add the opening bracket right after the function name, to do it the same way for all functions in this file. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for TP-Link TL-WDR4900 v2Chuanhong Guo2018-08-114-2/+245
| | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 8 MB - RAM: 128 MB - Ethernet: AR8327N with 5 GE ports. - Wireless radio: QCA9558 for 2.4G and AR9580 for 5G. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* uci: bump to source date 2018-08-11Yousong Zhou2018-08-111-3/+3
| | | | | | Fixes segfault when parsing malformed delta lines Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kernel: bump 4.14 to 4.14.62Koen Vandeputte2018-08-105-23/+10
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.119Koen Vandeputte2018-08-105-97/+15
| | | | | | | | | | | | Refreshed all patches. Delete upstreamed patch: - 100-tcp-add-tcp_ooo_try_coalesce-helper.patch Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* wpa_supplicant: fix CVE-2018-14526John Crispin2018-08-101-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Unauthenticated EAPOL-Key decryption in wpa_supplicant Published: August 8, 2018 Identifiers: - CVE-2018-14526 Latest version available from: https://w1.fi/security/2018-1/ Vulnerability A vulnerability was found in how wpa_supplicant processes EAPOL-Key frames. It is possible for an attacker to modify the frame in a way that makes wpa_supplicant decrypt the Key Data field without requiring a valid MIC value in the frame, i.e., without the frame being authenticated. This has a potential issue in the case where WPA2/RSN style of EAPOL-Key construction is used with TKIP negotiated as the pairwise cipher. It should be noted that WPA2 is not supposed to be used with TKIP as the pairwise cipher. Instead, CCMP is expected to be used and with that pairwise cipher, this vulnerability is not applicable in practice. When TKIP is negotiated as the pairwise cipher, the EAPOL-Key Key Data field is encrypted using RC4. This vulnerability allows unauthenticated EAPOL-Key frames to be processed and due to the RC4 design, this makes it possible for an attacker to modify the plaintext version of the Key Data field with bitwise XOR operations without knowing the contents. This can be used to cause a denial of service attack by modifying GTK/IGTK on the station (without the attacker learning any of the keys) which would prevent the station from accepting received group-addressed frames. Furthermore, this might be abused by making wpa_supplicant act as a decryption oracle to try to recover some of the Key Data payload (GTK/IGTK) to get knowledge of the group encryption keys. Full recovery of the group encryption keys requires multiple attempts (128 connection attempts per octet) and each attempt results in disconnection due to a failure to complete the 4-way handshake. These failures can result in the AP/network getting disabled temporarily or even permanently (requiring user action to re-enable) which may make it impractical to perform the attack to recover the keys before the AP has already changes the group keys. By default, wpa_supplicant is enforcing at minimum a ten second wait time between each failed connection attempt, i.e., over 20 minutes waiting to recover each octet while hostapd AP implementation uses 10 minute default for GTK rekeying when using TKIP. With such timing behavior, practical attack would need large number of impacted stations to be trying to connect to the same AP to be able to recover sufficient information from the GTK to be able to determine the key before it gets changed. Vulnerable versions/configurations All wpa_supplicant versions. Acknowledgments Thanks to Mathy Vanhoef of the imec-DistriNet research group of KU Leuven for discovering and reporting this issue. Possible mitigation steps - Remove TKIP as an allowed pairwise cipher in RSN/WPA2 networks. This can be done also on the AP side. - Merge the following commits to wpa_supplicant and rebuild: WPA: Ignore unauthenticated encrypted EAPOL-Key data This patch is available from https://w1.fi/security/2018-1/ - Update to wpa_supplicant v2.7 or newer, once available Signed-off-by: John Crispin <john@phrozen.org>
* tools: findutils: fix compilation with glibc 2.28Luis Araneda2018-08-101-0/+104
| | | | | | | Add a temporary workaround to compile with glibc 2.28 as some constants were removed and others made private Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* tools: m4: fix compilation with glibc 2.28Luis Araneda2018-08-101-0/+118
| | | | | | | Add a temporary workaround to compile with glibc 2.28 as some constants were removed and others made private Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* base-files: make wifi report unknown commandThibaut VARÈNE2018-08-101-2/+3
| | | | | | | | | | | Avoid having /sbin/wifi silently ignore unknown keywords and execute "up"; instead display the help message and exit with an error. Spell out the "up" keyword (which has users), add it to usage output, and preserve the implicit assumption that runing /sbin/wifi without argument performs "up". Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: add support for OCEDO KoalaDavid Bauer2018-08-095-0/+185
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: remove PHY resetChuanhong Guo2018-08-096-22/+6
| | | | | | | | | | | | Bit 8/12 of reset controller which is marked as PHY_RESET/SWITCH_RESET in datasheets will trigger either a reset for builtin switch or assert an external ETH0_RESET_L/ETH1_RESET_L pin, which are usually connected to external PHY/switch. None of them should be triggered every time an interface is brought up in ethernet driver. Remove PHY reset support from ag71xx and definition for them in dtsi. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-08-097-9/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros QCA9558. Ported from ar71xx target. Specification: - Qualcomm Atheros QCA9558 - 64 MB of RAM - 16 MB of Flash - 5x 10/100/1000 Ethernet - QCA8337N - 4x LEDs, 2x keys - UART header on PCB - Vcc, TX, RX, GND from LED side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Connect power cable to BHR-4GRV2 and turn on it 3. Access to "http://192.168.12.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新実行") button 5. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* odhcp6c: apply IPv6/ND configuration earlierHans Dedecker2018-08-092-8/+9
| | | | | | | | | | Apply IPv6/ND configuration before proto_send_update so that all config info is available when netifd is handling the notify_proto ubus call. In particular this fixes an issue when netifd is updating the downstream IPv6 mtu as netifd was still using the not yet updated upstream IPv6 mtu to set the downstream IPv6 mtu Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: fix PLL settings for QCA955xDavid Bauer2018-08-093-2/+10
| | | | | | | | | | | | | | This adds PLL settings for the ethernet ports of the TP-Link TL-WR1043 v2/v3 and the Openmesh OM5P-AC-v2. We also change the PLL-settings in the qca9557.dtsi to match the ones used as default on the ar71xx target. As of 4b9680f138 those devices have broken ethernet ports as the default PLL settings defined in the QCA9557.dtsi are applied which are off for those devices. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add pll for archer c7Kevin Darbyshire-Bryant2018-08-091-0/+2
| | | | | | | | | | | | | | | | | | commit 4b9680f fixed pll settings and the correct pll set by bootloader is overrided by value in qca9557.dtsi which is incorrect for Archer C7 and breaks ethernet. Add pll values for archer c7 to fix ethernet connection. This individual pll tweak has been cherry picked from github pr 1260 which changes a couple of things in a single commit and should be ideally split. This commit get archer v7 back and working. Tested: archer c7 v2 Original combined commit authored by: Signed-off-by: Chuanhong Guo <gch981213@gmail.com> c7 fix only split out by: Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* iproute2: remove libutil from InstallDev sectionHans Dedecker2018-08-091-3/+2
| | | | | | | | | | | Commit 4d961538f6 added libutil to the iproute2 InstallDev section but lead to compile issues with packages picking up the wrong libutil since libutil is quite a generic name ... Further libutil is rather meant for internal usage in iproute2 than a public API; therefore let's remove it from the InstallDev section together with ll_map.h Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: update to latest git HEADHans Dedecker2018-08-091-3/+3
| | | | | | 115a694 interface-ip: always override downstream IPv6 mtu Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* sunxi: change Orange Pi PC2 MUSB/power buttonAntonio Silverio2018-08-091-0/+20
| | | | | | | Changed default role of Orange Pi PC2 MSUB port to host (in dts) Changed default function of Orange Pi PC2 power button to PWR_BTN Signed-off-by: Antonio Silverio <menion@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 05:01:01 +0000