aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* scripts/om-fwupgradecfg-gen.sh: Fix u-boot image md5sum checkSven Eckelmann2016-09-211-0/+3
| | | | | | | | | | | The u-boot on Open Mesh devices checks the whole transfered image against a md5sum. This is stored inside the option filemd5sum inside the fwupgrade.cfg. The bootloader will not check it when this setting is missing and could therefore write invalid images to the flash. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46925
* ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR1750Sven Eckelmann2016-09-211-1/+23
| | | | | | | | | | | | The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work correctly under OpenWrt. But the global function ath79_setup_qca955x_eth_cfg will not unset all of them to increase the backward compatiblity with older mach-* files. A private (simplified) version for MR1750 can be used instead. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r49070
* ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR900Sven Eckelmann2016-09-211-1/+23
| | | | | | | | | | | | The MR900 must unset some bits in ETH_CFG which were set by u-boot to work correctly under OpenWrt. But the global function ath79_setup_qca955x_eth_cfg will not unset all of them to increase the backward compatiblity with older mach-* files. A private (simplified) version for MR900 can be used instead. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r49069
* ar71xx: Use PHY fixups for Open Mesh MR1750Sven Eckelmann2016-09-211-3/+22
| | | | | | | | | | | | | | | | | | The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in different ways. u-boot only modifies the ETH_CFG of the QCA955x based on the link speed. But OpenWrt can only modify the PHY delays based on the link speed. This can lead to communication problems when u-boot initializes the ETH_CFG for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY delays to an incompatible value. Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and only rely on the AT803x PHY settings. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r49031
* ar71xx: Use PHY fixups for Open Mesh MR900Sven Eckelmann2016-09-211-3/+22
| | | | | | | | | | | | | | | | | | The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in different ways. u-boot only modifies the ETH_CFG of the QCA955x based on the link speed. But OpenWrt can only modify the PHY delays based on the link speed. This can lead to communication problems when u-boot initializes the ETH_CFG for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY delays to an incompatible value. Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and only rely on the AT803x PHY settings. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r49030
* ar71xx: Add QCA955X GPIO mux and function definitionsSven Eckelmann2016-09-212-28/+77
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r49075
* ar71xx: Add support for ath79_gpio_function_* on QCA955XSven Eckelmann2016-09-211-1/+11
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r49074
* ar71xx: Allow to use ath79_gpio_output_select on QCA955xSven Eckelmann2016-09-211-0/+60
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46459
* ar71xx: Use *_eth_cfg helper for Open Mesh MR900 boardsSven Eckelmann2016-09-211-20/+1
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46241
* ar71xx: Extend the list of bits in QCA955X_GMAC_REG_ETH_CFGSven Eckelmann2016-09-211-1/+18
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r49027
* ar71xx: create profile and build image for the OpenMesh MR1750 boardSven Eckelmann2016-09-212-2/+14
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46932
* package/uboot-envtools: add OpenMesh MR1750 supportSven Eckelmann2016-09-211-0/+1
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46931
* package/om-watchdog: add OpenMesh MR1750 supportSven Eckelmann2016-09-211-1/+1
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46930
* ar71xx: enable sysupgrade for the OpenMesh MR1750Sven Eckelmann2016-09-212-1/+8
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46929
* scripts/om-fwupgradecfg-gen.sh: add support for the MR1750Sven Eckelmann2016-09-211-2/+2
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46928
* ar71xx: add user-space support for the OpenMesh MR1750 boardSven Eckelmann2016-09-214-0/+13
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46927
* ar71xx: add kernel support for the OpenMesh MR1750 boardSven Eckelmann2016-09-213-0/+169
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Backport of r46926
* ar71xx: Generate sysupgrade images for OpenMesh devicesSven Eckelmann2016-09-211-0/+3
| | | | | | | | | | | | Some OpenWrt based firmwares like Gluon expect that a sysupgrade image exists when a device firmware can be updated via sysupgrade. This image wasn't created until now because OpenMesh devices use the same image for factory and sysupgrade flash. Copying the image from *factory.bin to *sysupgrade.bin is therefore enough to make the sysupgrade functionality visible. Reported-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* Merge pull request #83 from ecsv/gcc6Zoltan Herpai2016-09-214-93/+850
|\ | | | | toolchain: fix build with GCC 6
| * toolchain: gcc: fix build with GCC 6Matthias Schiffer2016-09-011-0/+130
| | | | | | | | | | | | | | At least for GCC 4.8, which is used by most targets. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
| * tools: mkimage: sync include/linux/compiler*.h with u-boot masterMatthias Schiffer2016-09-012-93/+702
| | | | | | | | | | | | | | Fixes build with GCC 6. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
| * tools: pkg-config: fix build with GCC 6Matthias Schiffer2016-09-011-0/+18
|/ | | | | | | | | | | | Fixes the following error: gdate.c: In function ‘g_date_strftime’: gdate.c:2497:7: error: format not a string literal, format string not checked [-Werror=format-nonliteral] tmplen = strftime (tmpbuf, tmpbufsize, locale_format, &tm); ^~~~~~ Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* iw: backport support for "channels" commandRafał Miłecki2016-06-191-0/+234
| | | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49388 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49389 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: brcmfmac: fix support for BCM4366Rafał Miłecki2016-06-193-0/+233
| | | | | | | | | | | | 1) Fix setting AP channel 2) Improve BSS management to avoid: [ 3602.929199] brcmfmac: brcmf_ap_add_vif: timeout occurred Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49383 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49386 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: brcmfmac: add support for get_channelRafał Miłecki2016-06-192-0/+338
| | | | | | | | | | | It's very useful for debugging problems with brcmfmac setting requested channel. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49382 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49385 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: brcmfmac: fix support for up to 4 AP interfacesRafał Miłecki2016-06-193-2/+121
| | | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49381 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49384 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: brcmfmac: return -ENFILE if interface existsRafał Miłecki2016-06-191-1/+1
| | | | | | | | | This makes brcmfmac compatible with mac80211 which uses dev_alloc_name (and so returns -ENFILE on error). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49378 3c298f89-4303-0410-b956-a3cf2f4a3e73
* openssl: Update to version 1.0.2hLuka Perkov2016-06-191-2/+2
| | | | | | | | | | | | openssl: Update to version 1.0.2h Bump to the latest version, fixes several security issues: * CVE-2016-2107, CVE-2016-2105, CVE-2016-2106, CVE-2016-2109, CVE-2016-2176 More details at https://www.openssl.org/news/openssl-1.0.2-notes.html Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49363 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: seama: exit with error if Seama header wasn't foundRafał Miłecki2016-06-191-1/+1
| | | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49314 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49315 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: seama: fix image data handlingRafał Miłecki2016-06-191-28/+18
| | | | | | | | | | | | | | | | 1) Put sanity checks in one place 2) Respect provided offset 3) Read only as much data as needed for MD5 calculation Thanks to the last change this is a great speedup and memory saver. On devices with NAND flash we were allocating & reading about 128 MiB while something about 8 MiB is enough. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49309 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49313 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: seama: move buf allocation to the MD5 functionRafał Miłecki2016-06-191-16/+22
| | | | | | | | | | This buf is only used in this function now, so lets move it there. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49308 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49312 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: seama: update MD5 using header in the first block bufferRafał Miłecki2016-06-191-4/+3
| | | | | | | | | | | This will allow separating first block buffer from a buffer used for MD5 calculation. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49307 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49311 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: seama: add md5 to header structRafał Miłecki2016-06-192-12/+11
| | | | | | | | | | | This allows us to drop some extra offset calculations and simplifies code a bit. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49306 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49310 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: check for Seama magic early when fixing MD5Rafał Miłecki2016-06-191-7/+21
| | | | | | | | | | | This avoid long (and unneeded) process of reading all data in case of running on MTD not containig Seama entity. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49304 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49305 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: add missing breaks in a switchRafał Miłecki2016-06-191-0/+2
| | | | | | | | | | | On platforms supporting both: TRX and Seama calling "fixtrx" was resulting in trying to fix Seama as well. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49301 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49303 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mtd: use tabs for indentsRafał Miłecki2016-06-191-7/+7
| | | | | | | | | | This makes code style consistent across the whole file. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r49300 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49302 3c298f89-4303-0410-b956-a3cf2f4a3e73
* hostapd: backport fix for AP SME drivers with monitor mode supportRafał Miłecki2016-06-191-0/+48
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49299 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: use backported versions of bgmac patchesRafał Miłecki2016-06-197-41/+61
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49298 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: use backported versions of bcma USB patchesRafał Miłecki2016-06-1912-55/+83
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49297 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ubox: turn logd into a separate packageLuka Perkov2016-06-192-4/+18
| | | | | | | | | Currently system log is always included as a part of ubox. Add logd as a seperate package and add it to default packages list. Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49294 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: add support for BCM4366C0 in brcmfmacRafał Miłecki2016-04-272-0/+92
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49261 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Revert "ar71xx: change some TP-link modelnames (WR841, WA701, WA730)"John Crispin2016-04-261-11/+11
| | | | | | | | | | | | | | | This reverts commit 0fd48fd7dab066db8a46e51775579c9ef507ca25. We are facing some problem on rolling out the current 15.05-branch to our devices because the image name changed. The changed image name breaks compatibility for derived projects and that's something which should only happen if there is a really good reason (e.g. security fix). Signed-off-by: Tim Niemeyer <tim@tn-x.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49231 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: Fix LED handling.John Crispin2016-04-261-24/+32
| | | | | | | | | | | Backport of r47914 to CC. Without this patch the TDW8970 is left without any status LED at all, even during preinit and failsafe. Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49230 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: Fix ath9k LED for TDW8970.John Crispin2016-04-263-1/+22
| | | | | | | | | | Backport of r47911, r47912, r47969 to CC. All other required patches have already been backported in r48822. Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49229 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71x: Added support for TP-Link TL-WR841N v11 to 15.05John Crispin2016-04-251-1/+8
| | | | | | | | | | | | This patch adds support for the TP-Link TL-WR841N to OpenWrt Chaos Calmer 15.05. Confirmed working [1] and [2]. Signed-off by Stijn Segers <francesco.borromini@inventati.org> [1] https://forum.openwrt.org/viewtopic.php?id=63657 [2] https://forum.openwrt.org/viewtopic.php?id=61309 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49228 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: backport support for Netgear WPN824NJohn Crispin2016-04-2511-6/+185
| | | | | | | | | | | | | | | | Add support for Netgear WPN824N. Hardware specs: * AR7240, 4 LAN ports, 1 WAN port * AR9285 WLAN * 32 MB RAM * 4 MB Flash * 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color effect) * 3 Buttons (not supported) Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49227 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add TP-Link TL-WA901ND v4 support to Chaos Calmer 15.05.1John Crispin2016-04-2510-1/+177
| | | | | | | | | | | This patch backports support for the TP-Link TL-WA901ND v4 to Chaos Calmer 15.05.1, which was added into trunk recently [1]. Signed-off by Stijn Segers <francesco.borromini@inventati.org> [1]: http://patchwork.ozlabs.org/patch/606780/ git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49226 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add TP-Link TL-WR740N v6 support to 15.05.1John Crispin2016-04-251-1/+8
| | | | | | | | | | | | This patch adds support for the TP-Link TL-WR740N v6 to OpenWrt Chaos Calmer. Hardware wise, it's very similar to the TL-WR841N v10. See the forum thread [1]. Credit goes to the user 'traveler' who did the legwork and tested builds. Also thanks to Matthias Schiffer for clarifying the DEVICE_PROFILE settings. Signed-off by: Stijn Segers <francesco.borromini@inventati.org> [1]: https://forum.openwrt.org/viewtopic.php?pid=318704 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49225 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ramips: backport rt3352 usbphy fix in dts-fileJohn Crispin2016-04-251-1/+8
| | | | | | | | Backport of trunk patch. Fix kernel hang during loading ehci-hcd module. SIgned-Off-By: Serge Vasilugin <vasilugin@yandex.ru> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49224 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: kernel: Support for new Archer C7 with gd25q128 chipHauke Mehrtens2016-04-247-37/+39
| | | | | | | | | | | | | | | Archer C7 V2.0 units from December 2015 onwards ( serials starting 215C ) have changed flash chips to the gd25q128 chip, this is supported in trunk but not presently in 15.05. I would like stable support for this version so I've back ported the required fix from trunk and removed a conflicting patch from bcm53xx I've tested the patch it and I'm able to install a build of 15.05.1 on a new Archer C7 device with this patch. Signed-off-by: John Marrett <johnf@zioncluster.ca> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49220 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 00:03:01 +0000