aboutsummaryrefslogtreecommitdiffstats
path: root/target
diff options
context:
space:
mode:
Diffstat (limited to 'target')
-rwxr-xr-xtarget/linux/bcm53xx/base-files/etc/board.d/02_network7
-rw-r--r--target/linux/bcm53xx/base-files/etc/diag.sh3
-rw-r--r--target/linux/bcm53xx/base-files/lib/preinit/07_set_preinit_iface_bcm53xx14
-rw-r--r--target/linux/bcm53xx/base-files/lib/upgrade/platform.sh43
-rw-r--r--target/linux/bcm53xx/image/Makefile27
-rw-r--r--target/linux/bcm53xx/patches-5.4/330-ARM-BCM5301X-Add-DT-for-Meraki-MR32.patch261
-rw-r--r--target/linux/bcm53xx/patches-5.4/331-Meraki-MR32-Status-LEDs.patch28
7 files changed, 380 insertions, 3 deletions
diff --git a/target/linux/bcm53xx/base-files/etc/board.d/02_network b/target/linux/bcm53xx/base-files/etc/board.d/02_network
index 5752b7760d..231566cfa0 100755
--- a/target/linux/bcm53xx/base-files/etc/board.d/02_network
+++ b/target/linux/bcm53xx/base-files/etc/board.d/02_network
@@ -89,10 +89,15 @@ bcm53xx_setup_macs()
netgear,r8500)
# As vendor doesn't use eth0 its MAC may be missing. Use one from eth2.
et2macaddr="$(nvram get et2macaddr)"
- [ -n "$et2macaddr" ] && ucidef_set_interface_macaddr "lan" "$et2macaddr"
+ ;;
+ meraki,mr32)
+ # The MAC is stored on an AT24C64 eeprom and not on the nvram
+ et2macaddr=$(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66)
;;
esac
+ [ -n "$et2macaddr" ] && ucidef_set_interface_macaddr "lan" "$et2macaddr"
+
wan_macaddr="$(nvram get wan_hwaddr)"
case "$board" in
asus,rt-ac87u)
diff --git a/target/linux/bcm53xx/base-files/etc/diag.sh b/target/linux/bcm53xx/base-files/etc/diag.sh
index 1a9332327a..bf5b779aa8 100644
--- a/target/linux/bcm53xx/base-files/etc/diag.sh
+++ b/target/linux/bcm53xx/base-files/etc/diag.sh
@@ -18,6 +18,9 @@ get_status_led() {
status_led=$(basename $status_led_file)
return
fi;
+
+ # And finally, let's also try the device-Tree aliases node
+ status_led="$(get_dt_led status)"
}
set_state() {
diff --git a/target/linux/bcm53xx/base-files/lib/preinit/07_set_preinit_iface_bcm53xx b/target/linux/bcm53xx/base-files/lib/preinit/07_set_preinit_iface_bcm53xx
new file mode 100644
index 0000000000..9e7c4b821e
--- /dev/null
+++ b/target/linux/bcm53xx/base-files/lib/preinit/07_set_preinit_iface_bcm53xx
@@ -0,0 +1,14 @@
+set_preinit_iface() {
+ . /lib/functions.sh
+
+ case $(board_name) in
+ meraki,mr32)
+ # switch needs to be out of the vlan mode.
+ swconfig dev switch0 set reset 1
+ swconfig dev switch0 set enable_vlan 0
+ swconfig dev switch0 set apply 1
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main set_preinit_iface
diff --git a/target/linux/bcm53xx/base-files/lib/upgrade/platform.sh b/target/linux/bcm53xx/base-files/lib/upgrade/platform.sh
index 40b2ef67be..cbb8290275 100644
--- a/target/linux/bcm53xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/bcm53xx/base-files/lib/upgrade/platform.sh
@@ -96,7 +96,7 @@ platform_identify() {
echo "unknown"
}
-platform_check_image() {
+platform_other_check_image() {
[ "$#" -gt 1 ] && return 1
local file_type=$(platform_identify "$1")
@@ -227,6 +227,25 @@ platform_check_image() {
return $error
}
+platform_check_image() {
+ case "$(board_name)" in
+ meraki,mr32)
+ # Ideally, REQUIRE_IMAGE_METADATA=1 would suffice
+ # but this would require converting all other
+ # devices too.
+ nand_do_platform_check meraki-mr32 "$1"
+ return $?
+ ;;
+ *)
+ platform_other_check_image "$1"
+ return $?
+ ;;
+ esac
+
+ return 1
+}
+
+
# $(1): image for upgrade (with possible extra header)
# $(2): offset of trx in image
platform_do_upgrade_nand_trx() {
@@ -393,7 +412,7 @@ platform_img_from_seama() {
echo -n $dir/image-entity.bin
}
-platform_do_upgrade() {
+platform_other_do_upgrade() {
local file_type=$(platform_identify "$1")
local trx="$1"
local cmd=
@@ -424,3 +443,23 @@ platform_do_upgrade() {
default_do_upgrade "$trx" "$cmd"
}
+
+platform_do_upgrade() {
+ case "$(board_name)" in
+ meraki,mr32)
+ CI_KERNPART="part.safe"
+ nand_do_upgrade "$1"
+ ;;
+ *)
+ platform_other_do_upgrade "$1"
+ ;;
+ esac
+}
+
+platform_nand_pre_upgrade() {
+ case "$(board_name)" in
+ meraki,mr32)
+ CI_KERNPART="part.safe"
+ ;;
+ esac
+}
diff --git a/target/linux/bcm53xx/image/Makefile b/target/linux/bcm53xx/image/Makefile
index 768477160a..9ceb5f6212 100644
--- a/target/linux/bcm53xx/image/Makefile
+++ b/target/linux/bcm53xx/image/Makefile
@@ -320,6 +320,33 @@ define Device/luxul_xwr-3150
endef
TARGET_DEVICES += luxul_xwr-3150
+define Device/meraki_mr32
+ DEVICE_VENODR := Meraki
+ DEVICE_MODEL := MR32
+ DEVICE_PACKAGES := $(B43) kmod-i2c-bcm-iproc kmod-i2c-gpio kmod-eeprom-at24 \
+ kmod-leds-pwm kmod-hwmon-ina2xx kmod-bluetooth
+ DEVICE_DTS := bcm53016-meraki-mr32
+# Meraki FW r23 tries to resize the part.safe partition before it will
+# flash the image. This is a bit of a problem, since resizing will fail
+# if the partition is smaller than the old one.
+ KERNEL_LOADADDR := 0x00008000
+ KERNEL_INITRAMFS_SUFFIX := .bin
+ KERNEL_INITRAMFS := kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb | \
+ pad-to 10362880
+ KERNEL := kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+
+# Currently the only device that uses the new image check
+ SUPPORTED_DEVICES := meraki,mr32
+
+# The loader is specifically looking for fdt@2:
+# [ 3.190000] find_itb_subimage: error finding fdt@2: FDT_ERR_NOTFOUND
+# The image won't boot, if it isn't found. :(
+ DEVICE_FDT_NUM := 2
+endef
+TARGET_DEVICES += meraki_mr32
+
define Device/netgear
DEVICE_VENDOR := NETGEAR
IMAGES := chk
diff --git a/target/linux/bcm53xx/patches-5.4/330-ARM-BCM5301X-Add-DT-for-Meraki-MR32.patch b/target/linux/bcm53xx/patches-5.4/330-ARM-BCM5301X-Add-DT-for-Meraki-MR32.patch
new file mode 100644
index 0000000000..29329eb3f0
--- /dev/null
+++ b/target/linux/bcm53xx/patches-5.4/330-ARM-BCM5301X-Add-DT-for-Meraki-MR32.patch
@@ -0,0 +1,261 @@
+From ec88a9c344d9fd8c3b11bff1f99a0b6248ae256d Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Sat, 22 Aug 2020 18:19:23 +0200
+Subject: [PATCH] ARM: BCM5301X: Add DT for Meraki MR32
+
+add support for the Cisco Meraki MR32.
+This is a dual-band enterprise class 802.11ac access point.
+The unit was donated by Chris Blake. Thank you!
+
+SoC: Broadcom BCM53016A1 (1 GHz, 2 cores)
+RAM: 128 MiB
+NAND: 128 MiB Spansion S34ML01G2 (~114 MiB useable)
+ETH: 1GBit Ethernet Port - PoE
+WIFI1: Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
+WIFI2: Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
+WIFI3: Broadcom BCM43428 abgn (1x1:1 - id: 43428)
+
+BLE: Broadcom BCM20732 (ttyS1)
+LEDS: 1 x Programmable RGB Status LED (driven by a PWM)
+ 1 x White LED (GPIO)
+ 1 x Orange LED Fault Indicator (GPIO)
+ 2 x LAN Activity / Speed LEDs (On the RJ45 Port)
+BUTTON: one Reset button
+MISC: AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC)
+ ina219 hardware monitor (i2c)
+ Kensington Lock
+
+SERIAL:
+ WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
+ The Serial setting is 115200-8-N-1. The board has a populated
+ right angle 1x4 0.1" pinheader.
+ The pinout is: VCC, RX, TX, GND.
+
+Odd stuff:
+ - uart0 clock frequency is 62.5 MHz.
+ - The LEDs are labeled as SYS-LED1 through SYS-LED3
+ because of the silkscreen on the PCB.
+ - the original u-boot has been compiled with most functions
+ and commands disabled. The u-boot env isn't setup properly
+ either and as a result, the bcm47xxpart probing is not
+ working. Hence, the nand partitions are specified through a
+ "fixed-partition" binding.
+ - The "WICED SMART(TM)" Bluetooth LE 4.0 BCM20732 chip is
+ connected to uart2 of the SoC. The BCM20732 does not
+ provide a HCI. So the linux' bluetooth stack is useless.
+ The mock-up node with the compatible binding and
+ enable-gpios property is provided solely as documentation.
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -119,6 +119,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm47094-luxul-xwr-3150-v1.dtb \
+ bcm47094-netgear-r8500.dtb \
+ bcm47094-phicomm-k3.dtb \
++ bcm53016-meraki-mr32.dtb \
+ bcm94708.dtb \
+ bcm94709.dtb \
+ bcm953012er.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
+@@ -0,0 +1,197 @@
++// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
++/*
++ * Broadcom BCM470X / BCM5301X ARM platform code.
++ * DTS for Meraki MR32 / Codename: Espresso
++ *
++ * Copyright (C) 2018-2020 Christian Lamparter <chunkeey@gmail.com>
++ */
++
++/dts-v1/;
++
++#include "bcm4708.dtsi"
++#include "bcm5301x-nand-cs0-bch8.dtsi"
++#include <dt-bindings/leds/common.h>
++
++/ {
++ compatible = "meraki,mr32", "brcm,brcm53016", "brcm,bcm4708";
++ model = "Meraki MR32";
++
++ chosen {
++ bootargs = " console=ttyS0,115200n8 earlycon";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000>;
++ device_type = "memory";
++ };
++
++ aliases {
++ serial1 = &uart2;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ sysled3 {
++ function = LED_FUNCTION_FAULT;
++ color = <LED_COLOR_ID_AMBER>;
++ gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
++ panic-indicator;
++ };
++ sysled2 {
++ function = LED_FUNCTION_INDICATOR;
++ color = <LED_COLOR_ID_WHITE>;
++ gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
++ };
++ };
++
++ keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ pwm-leds {
++ compatible = "pwm-leds";
++
++ red {
++ /* SYS-LED 1 - Tricolor */
++ function = LED_FUNCTION_INDICATOR;
++ color = <LED_COLOR_ID_RED>;
++ pwms = <&pwm 0 50000 0>;
++ max-brightness = <255>;
++ };
++
++ green {
++ /* SYS-LED 1 - Tricolor */
++ function = LED_FUNCTION_POWER;
++ color = <LED_COLOR_ID_GREEN>;
++ pwms = <&pwm 1 50000 0>;
++ max-brightness = <255>;
++ };
++
++ blue {
++ /* SYS-LED 1 - Tricolor */
++ function = LED_FUNCTION_INDICATOR;
++ color = <LED_COLOR_ID_BLUE>;
++ pwms = <&pwm 2 50000 0>;
++ max-brightness = <255>;
++ };
++ };
++
++ i2c {
++ /*
++ * The platform provided I2C does not budge.
++ * This is a replacement until I can figure
++ * out what are the missing bits...
++ */
++
++ compatible = "i2c-gpio";
++ sda-gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
++ scl-gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
++ i2c-gpio,delay-us = <10>; /* close to 100 kHz */
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ current_sense: ina219@45 {
++ compatible = "ti,ina219";
++ reg = <0x45>;
++ shunt-resistor = <60000>; /* = 60 mOhms */
++ };
++
++ eeprom: eeprom@50 {
++ compatible = "atmel,24c64";
++ reg = <0x50>;
++ pagesize = <32>;
++ read-only;
++ };
++ };
++};
++
++&uart0 {
++ clock-frequency = <62500000>;
++ /delete-property/ clocks;
++};
++
++&uart1 {
++ status = "disabled";
++};
++
++&uart2 {
++ status = "okay";
++ /*
++ * bluetooth-le {
++ * compatible = "brcm,bcm20732";
++ * enable-gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
++ *};
++ */
++};
++
++&gmac1 {
++ status = "disabled";
++};
++&gmac2 {
++ status = "disabled";
++};
++&gmac3 {
++ status = "disabled";
++};
++
++&pwm {
++ status = "okay";
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinmux_pwm>;
++};
++
++&nandcs {
++ nand-ecc-algo = "hw";
++
++ partitions {
++ /*
++ * The partition autodetection does not work for this device.
++ * It will only detect the "nvram" partition with an incorrect size.
++ * [ 1.721667] 1 bcm47xxpart partitions found on MTD device brcmnand.0
++ * [ 1.727962] Creating 1 MTD partitions on "brcmnand.0":
++ * [ 1.733117] 0x000000400000-0x000008000000 : "nvram"
++ */
++
++ compatible = "fixed-partitions";
++ #address-cells = <0x1>;
++ #size-cells = <0x1>;
++
++ partition0@0 {
++ label = "u-boot";
++ reg = <0x0 0x100000>;
++ read-only;
++ };
++
++ partition1@100000 {
++ label = "bootkernel1";
++ reg = <0x100000 0x300000>;
++ read-only;
++ };
++
++ partition2@400000 {
++ label = "nvram";
++ reg = <0x400000 0x100000>;
++ read-only;
++ };
++
++ partition3@500000 {
++ label = "bootkernel2";
++ reg = <0x500000 0x300000>;
++ read-only;
++ };
++
++ partition4@800000 {
++ label = "ubi";
++ reg = <0x800000 0x7780000>;
++ };
++ };
++};
diff --git a/target/linux/bcm53xx/patches-5.4/331-Meraki-MR32-Status-LEDs.patch b/target/linux/bcm53xx/patches-5.4/331-Meraki-MR32-Status-LEDs.patch
new file mode 100644
index 0000000000..fb78ee93c4
--- /dev/null
+++ b/target/linux/bcm53xx/patches-5.4/331-Meraki-MR32-Status-LEDs.patch
@@ -0,0 +1,28 @@
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Thu, 7 Jun 2018 19:29:12 +0200
+Subject: bcm53xx: add LED status label alias for Meraki MR32
+
+add an led-status alias label. This is used by OpenWrt's LED
+DTS lookup function to identifiy the indicator LED
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+
+--- a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
++++ b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
+@@ -27,6 +27,7 @@
+
+ aliases {
+ serial1 = &uart2;
++ led-status = &led_status;
+ };
+
+ leds {
+@@ -68,7 +69,7 @@
+ max-brightness = <255>;
+ };
+
+- green {
++ led_status: green {
+ /* SYS-LED 1 - Tricolor */
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_GREEN>;