diff options
Diffstat (limited to 'target')
| -rw-r--r-- | target/linux/at91/config-default (renamed from target/linux/at91/config-2.6.34) | 0 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/000-at91patches.patch | 13019 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/001-vlink-machine.patch | 229 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/002-led-driver.patch | 167 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/003-gpio-driver.patch | 546 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/007-mtd-partition.patch | 36 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/008-fdl-serial.patch | 161 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/009-fdl-uartinit.patch | 34 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/010-dm9161a-phyfix.patch | 28 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/014-initpartition.patch | 18 | ||||
| -rw-r--r-- | target/linux/at91/patches-2.6.25/017-usb_serial_endpoint_size.patch | 11 |
11 files changed, 0 insertions, 14249 deletions
diff --git a/target/linux/at91/config-2.6.34 b/target/linux/at91/config-default index 8abb310658..8abb310658 100644 --- a/target/linux/at91/config-2.6.34 +++ b/target/linux/at91/config-default diff --git a/target/linux/at91/patches-2.6.25/000-at91patches.patch b/target/linux/at91/patches-2.6.25/000-at91patches.patch deleted file mode 100644 index 06c29351ec..0000000000 --- a/target/linux/at91/patches-2.6.25/000-at91patches.patch +++ /dev/null @@ -1,13019 +0,0 @@ ---- a/arch/arm/mach-at91/Kconfig -+++ b/arch/arm/mach-at91/Kconfig -@@ -12,18 +12,28 @@ config ARCH_AT91RM9200 - - config ARCH_AT91SAM9260 - bool "AT91SAM9260 or AT91SAM9XE" -+ select GENERIC_TIME -+ select GENERIC_CLOCKEVENTS - - config ARCH_AT91SAM9261 - bool "AT91SAM9261" -+ select GENERIC_TIME -+ select GENERIC_CLOCKEVENTS - - config ARCH_AT91SAM9263 - bool "AT91SAM9263" -+ select GENERIC_TIME -+ select GENERIC_CLOCKEVENTS - - config ARCH_AT91SAM9RL - bool "AT91SAM9RL" -+ select GENERIC_TIME -+ select GENERIC_CLOCKEVENTS - - config ARCH_AT91CAP9 - bool "AT91CAP9" -+ select GENERIC_TIME -+ select GENERIC_CLOCKEVENTS - - config ARCH_AT91X40 - bool "AT91x40" -@@ -45,7 +55,7 @@ config MACH_ONEARM - depends on ARCH_AT91RM9200 - help - Select this if you are using Ajeco's 1ARM Single Board Computer. -- <http://www.ajeco.fi/products.htm> -+ <http://www.ajeco.fi/eng/products_e.htm> - - config ARCH_AT91RM9200DK - bool "Atmel AT91RM9200-DK Development board" -@@ -94,7 +104,7 @@ config MACH_KB9200 - depends on ARCH_AT91RM9200 - help - Select this if you are using KwikByte's KB920x board. -- <http://kwikbyte.com/KB9202_description_new.htm> -+ <http://www.kwikbyte.com/KB9202.html> - - config MACH_PICOTUX2XX - bool "picotux 200" -@@ -109,6 +119,38 @@ config MACH_KAFA - help - Select this if you are using Sperry-Sun's KAFA board. - -+config MACH_CHUB -+ bool "Promwad Chub board" -+ depends on ARCH_AT91RM9200 -+ help -+ Select this if you are using Promwad's Chub board. -+ -+config MACH_HOMEMATIC -+ bool "eQ-3 HomeMatic" -+ depends on ARCH_AT91RM9200 -+ help -+ Select this if you are using eQ-3's HomeMatic device. -+ <http://www.eq-3.com> -+ -+config MACH_ECBAT91 -+ bool "emQbit ECB_AT91 SBC" -+ depends on ARCH_AT91RM9200 -+ help -+ Select this if you are using emQbit's ECB_AT91 board. -+ <http://wiki.emqbit.com/free-ecb-at91> -+ -+config MACH_SWEDATMS -+ bool "Sweda TMS Board" -+ depends on ARCH_AT91RM9200 -+ help -+ Select this if you are using Sweda TMS-100 board. -+ -+config MACH_TT9200 -+ bool "Toptech TT9200" -+ depends on ARCH_AT91RM9200 -+ help -+ Select this if you are using Toptech's TT9200 board. -+ - endif - - # ---------------------------------------------------------- -@@ -133,6 +175,34 @@ config MACH_AT91SAM9260EK - Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit - <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933> - -+config MACH_CAM60 -+ bool "KwikByte KB9260 (CAM60) board" -+ depends on ARCH_AT91SAM9260 -+ help -+ Select this if you are using KwikByte's KB9260 (CAM60) board based on the Atmel AT91SAM9260. -+ <http://www.kwikbyte.com/KB9260.html> -+ -+config MACH_SAM9_L9260 -+ bool "Olimex SAM9-L9260 board" -+ depends on ARCH_AT91SAM9260 -+ help -+ Select this if you are using Olimex's SAM9-L9260 board based on the Atmel AT91SAM9260. -+ <http://www.olimex.com/dev/sam9-L9260.html> -+ -+config MACH_USB_A9260 -+ bool "CALAO USB-A9260" -+ depends on ARCH_AT91SAM9260 -+ help -+ Select this if you are using a Calao Systems USB-A9260. -+ <http://www.calao-systems.com> -+ -+config MACH_QIL_A9260 -+ bool "CALAO QIL-A9260 board" -+ depends on ARCH_AT91SAM9260 -+ help -+ Select this if you are using a Calao Systems QIL-A9260 Board. -+ <http://www.calao-systems.com> -+ - endif - - # ---------------------------------------------------------- -@@ -163,6 +233,13 @@ config MACH_AT91SAM9263EK - Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. - <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057> - -+config MACH_USB_A9263 -+ bool "CALAO USB-A9263" -+ depends on ARCH_AT91SAM9263 -+ help -+ Select this if you are using a Calao Systems USB-A9263. -+ <http://www.calao-systems.com> -+ - endif - - # ---------------------------------------------------------- -@@ -216,7 +293,7 @@ comment "AT91 Board Options" - - config MTD_AT91_DATAFLASH_CARD - bool "Enable DataFlash Card support" -- depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK) -+ depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK) - help - Enable support for the DataFlash card. - -@@ -237,6 +314,19 @@ config AT91_PROGRAMMABLE_CLOCKS - Select this if you need to program one or more of the PCK0..PCK3 - programmable clock outputs. - -+config AT91_SLOW_CLOCK -+ bool "Suspend-to-RAM disables main oscillator" -+ depends on SUSPEND -+ help -+ Select this if you want Suspend-to-RAM to save the most power -+ possible (without powering off the CPU) by disabling the PLLs -+ and main oscillator so that only the 32 KiHz clock is available. -+ -+ When only that slow-clock is available, some peripherals lose -+ functionality. Many can't issue wakeup events unless faster -+ clocks are available. Some lose their operating state and -+ need to be completely re-initialized. -+ - config AT91_TIMER_HZ - int "Kernel HZ (jiffies per second)" - range 32 1024 ---- a/arch/arm/mach-at91/Makefile -+++ b/arch/arm/mach-at91/Makefile -@@ -28,16 +28,26 @@ obj-$(CONFIG_MACH_CARMEVA) += board-carm - obj-$(CONFIG_MACH_KB9200) += board-kb9202.o - obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o - obj-$(CONFIG_MACH_KAFA) += board-kafa.o -+obj-$(CONFIG_MACH_CHUB) += board-chub.o - obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o -+obj-$(CONFIG_MACH_HOMEMATIC) += board-homematic.o -+obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o -+obj-$(CONFIG_MACH_SWEDATMS) += board-tms.o -+obj-$(CONFIG_MACH_TT9200) += board-tt9200.o - - # AT91SAM9260 board-specific support - obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o -+obj-$(CONFIG_MACH_CAM60) += board-cam60.o -+obj-$(CONFIG_MACH_SAM9_L9260) += board-sam9-l9260.o -+obj-$(CONFIG_MACH_USB_A9260) += board-usb-a9260.o -+obj-$(CONFIG_MACH_QIL_A9260) += board-qil-a9260.o - - # AT91SAM9261 board-specific support - obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o - - # AT91SAM9263 board-specific support - obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o -+obj-$(CONFIG_MACH_USB_A9263) += board-usb-a9263.o - - # AT91SAM9RL board-specific support - obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o -@@ -50,9 +60,11 @@ obj-$(CONFIG_MACH_AT91EB01) += board-eb0 - - # Drivers - obj-y += leds.o -+obj-$(CONFIG_FB_S1D13XXX) += ics1523.o - - # Power Management - obj-$(CONFIG_PM) += pm.o -+obj-$(CONFIG_AT91_SLOW_CLOCK) += pm_slowclock.o - - ifeq ($(CONFIG_PM_DEBUG),y) - CFLAGS_pm.o += -DDEBUG ---- a/arch/arm/mach-at91/at91cap9.c -+++ b/arch/arm/mach-at91/at91cap9.c -@@ -13,12 +13,15 @@ - */ - - #include <linux/module.h> -+#include <linux/pm.h> - - #include <asm/mach/arch.h> - #include <asm/mach/map.h> -+#include <asm/arch/cpu.h> - #include <asm/arch/at91cap9.h> - #include <asm/arch/at91_pmc.h> - #include <asm/arch/at91_rstc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - #include "clock.h" -@@ -288,6 +291,12 @@ static void at91cap9_reset(void) - at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); - } - -+static void at91cap9_poweroff(void) -+{ -+ at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -+} -+ -+ - /* -------------------------------------------------------------------- - * AT91CAP9 processor initialization - * -------------------------------------------------------------------- */ -@@ -298,6 +307,7 @@ void __init at91cap9_initialize(unsigned - iotable_init(at91cap9_io_desc, ARRAY_SIZE(at91cap9_io_desc)); - - at91_arch_reset = at91cap9_reset; -+ pm_power_off = at91cap9_poweroff; - at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1); - - /* Init clock subsystem */ -@@ -308,6 +318,12 @@ void __init at91cap9_initialize(unsigned - - /* Register GPIO subsystem */ - at91_gpio_init(at91cap9_gpio, 4); -+ -+ /* Remember the silicon revision */ -+ if (cpu_is_at91cap9_revB()) -+ system_rev = 0xB; -+ else if (cpu_is_at91cap9_revC()) -+ system_rev = 0xC; - } - - /* -------------------------------------------------------------------- ---- a/arch/arm/mach-at91/at91cap9_devices.c -+++ b/arch/arm/mach-at91/at91cap9_devices.c -@@ -13,18 +13,20 @@ - */ - #include <asm/mach/arch.h> - #include <asm/mach/map.h> -+#include <asm/mach/irq.h> - - #include <linux/dma-mapping.h> - #include <linux/platform_device.h> --#include <linux/mtd/physmap.h> -+#include <linux/i2c-gpio.h> - - #include <video/atmel_lcdc.h> - - #include <asm/arch/board.h> -+#include <asm/arch/cpu.h> - #include <asm/arch/gpio.h> - #include <asm/arch/at91cap9.h> --#include <asm/arch/at91sam926x_mc.h> - #include <asm/arch/at91cap9_matrix.h> -+#include <asm/arch/at91sam9_smc.h> - - #include "generic.h" - -@@ -69,6 +71,9 @@ void __init at91_add_device_usbh(struct - if (!data) - return; - -+ if (cpu_is_at91cap9_revB()) -+ set_irq_type(AT91CAP9_ID_UHP, IRQT_HIGH); -+ - /* Enable VBus control for UHP ports */ - for (i = 0; i < data->ports; i++) { - if (data->vbus_pin[i]) -@@ -84,6 +89,110 @@ void __init at91_add_device_usbh(struct - - - /* -------------------------------------------------------------------- -+ * USB HS Device (Gadget) -+ * -------------------------------------------------------------------- */ -+ -+#if defined(CONFIG_USB_GADGET_ATMEL_USBA) || defined(CONFIG_USB_GADGET_ATMEL_USBA_MODULE) -+ -+static struct resource usba_udc_resources[] = { -+ [0] = { -+ .start = AT91CAP9_UDPHS_FIFO, -+ .end = AT91CAP9_UDPHS_FIFO + SZ_512K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91CAP9_BASE_UDPHS, -+ .end = AT91CAP9_BASE_UDPHS + SZ_1K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [2] = { -+ .start = AT91CAP9_ID_UDPHS, -+ .end = AT91CAP9_ID_UDPHS, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \ -+ [idx] = { \ -+ .name = nam, \ -+ .index = idx, \ -+ .fifo_size = maxpkt, \ -+ .nr_banks = maxbk, \ -+ .can_dma = dma, \ -+ .can_isoc = isoc, \ -+ } -+ -+static struct usba_ep_data usba_udc_ep[] = { -+ EP("ep0", 0, 64, 1, 0, 0), -+ EP("ep1", 1, 1024, 3, 1, 1), -+ EP("ep2", 2, 1024, 3, 1, 1), -+ EP("ep3", 3, 1024, 2, 1, 1), -+ EP("ep4", 4, 1024, 2, 1, 1), -+ EP("ep5", 5, 1024, 2, 1, 0), -+ EP("ep6", 6, 1024, 2, 1, 0), -+ EP("ep7", 7, 1024, 2, 0, 0), -+}; -+ -+#undef EP -+ -+/* -+ * pdata doesn't have room for any endpoints, so we need to -+ * append room for the ones we need right after it. -+ */ -+static struct { -+ struct usba_platform_data pdata; -+ struct usba_ep_data ep[8]; -+} usba_udc_data; -+ -+static struct platform_device at91_usba_udc_device = { -+ .name = "atmel_usba_udc", -+ .id = -1, -+ .dev = { -+ .platform_data = &usba_udc_data.pdata, -+ }, -+ .resource = usba_udc_resources, -+ .num_resources = ARRAY_SIZE(usba_udc_resources), -+}; -+ -+void __init at91_add_device_usba(struct usba_platform_data *data) -+{ -+ if (cpu_is_at91cap9_revB()) { -+ set_irq_type(AT91CAP9_ID_UDPHS, IRQT_HIGH); -+ at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS | -+ AT91_MATRIX_UDPHS_BYPASS_LOCK); -+ } -+ else -+ at91_sys_write(AT91_MATRIX_UDPHS, AT91_MATRIX_SELECT_UDPHS); -+ -+ /* -+ * Invalid pins are 0 on AT91, but the usba driver is shared -+ * with AVR32, which use negative values instead. Once/if -+ * gpio_is_valid() is ported to AT91, revisit this code. -+ */ -+ usba_udc_data.pdata.vbus_pin = -EINVAL; -+ usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep); -+ memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));; -+ -+ if (data && data->vbus_pin > 0) { -+ at91_set_gpio_input(data->vbus_pin, 0); -+ at91_set_deglitch(data->vbus_pin, 1); -+ usba_udc_data.pdata.vbus_pin = data->vbus_pin; -+ } -+ -+ /* Pullup pin is handled internally by USB device peripheral */ -+ -+ /* Clocks */ -+ at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk"); -+ at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk"); -+ -+ platform_device_register(&at91_usba_udc_device); -+} -+#else -+void __init at91_add_device_usba(struct usba_platform_data *data) {} -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * Ethernet - * -------------------------------------------------------------------- */ - -@@ -246,7 +355,7 @@ void __init at91_add_device_mmc(short mm - } - - mmc0_data = *data; -- at91_clock_associate("mci0_clk", &at91cap9_mmc1_device.dev, "mci_clk"); -+ at91_clock_associate("mci0_clk", &at91cap9_mmc0_device.dev, "mci_clk"); - platform_device_register(&at91cap9_mmc0_device); - } else { /* MCI1 */ - /* CLK */ -@@ -283,10 +392,15 @@ static struct at91_nand_data nand_data; - #define NAND_BASE AT91_CHIPSELECT_3 - - static struct resource nand_resources[] = { -- { -+ [0] = { - .start = NAND_BASE, - .end = NAND_BASE + SZ_256M - 1, - .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91_BASE_SYS + AT91_ECC, -+ .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1, -+ .flags = IORESOURCE_MEM, - } - }; - -@@ -344,6 +458,7 @@ void __init at91_add_device_nand(struct - void __init at91_add_device_nand(struct at91_nand_data *data) {} - #endif - -+ - /* -------------------------------------------------------------------- - * TWI (i2c) - * -------------------------------------------------------------------- */ -@@ -532,17 +647,64 @@ void __init at91_add_device_spi(struct s - - - /* -------------------------------------------------------------------- -+ * Timer/Counter block -+ * -------------------------------------------------------------------- */ -+ -+#ifdef CONFIG_ATMEL_TCLIB -+ -+static struct resource tcb_resources[] = { -+ [0] = { -+ .start = AT91CAP9_BASE_TCB0, -+ .end = AT91CAP9_BASE_TCB0 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91CAP9_ID_TCB, -+ .end = AT91CAP9_ID_TCB, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91cap9_tcb_device = { -+ .name = "atmel_tcb", -+ .id = 0, -+ .resource = tcb_resources, -+ .num_resources = ARRAY_SIZE(tcb_resources), -+}; -+ -+static void __init at91_add_device_tc(void) -+{ -+ /* this chip has one clock and irq for all three TC channels */ -+ at91_clock_associate("tcb_clk", &at91cap9_tcb_device.dev, "t0_clk"); -+ platform_device_register(&at91cap9_tcb_device); -+} -+#else -+static void __init at91_add_device_tc(void) { } -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * RTT - * -------------------------------------------------------------------- */ - -+static struct resource rtt_resources[] = { -+ { -+ .start = AT91_BASE_SYS + AT91_RTT, -+ .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1, -+ .flags = IORESOURCE_MEM, -+ } -+}; -+ - static struct platform_device at91cap9_rtt_device = { - .name = "at91_rtt", -- .id = -1, -- .num_resources = 0, -+ .id = 0, -+ .resource = rtt_resources, -+ .num_resources = ARRAY_SIZE(rtt_resources), - }; - - static void __init at91_add_device_rtt(void) - { -+ device_init_wakeup(&at91cap9_rtt_device.dev, 1); - platform_device_register(&at91cap9_rtt_device); - } - -@@ -660,6 +822,9 @@ void __init at91_add_device_lcdc(struct - if (!data) - return; - -+ if (cpu_is_at91cap9_revB()) -+ set_irq_type(AT91CAP9_ID_LCDC, IRQT_HIGH); -+ - at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */ - at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */ - at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */ -@@ -990,7 +1155,7 @@ static inline void configure_usart2_pins - at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */ - } - --static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ - struct platform_device *atmel_default_console_device; /* the serial console device */ - - void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) -@@ -1031,8 +1196,6 @@ void __init at91_set_serial_console(unsi - { - if (portnr < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[portnr]; -- if (!atmel_default_console_device) -- printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - - void __init at91_add_device_serial(void) -@@ -1043,6 +1206,9 @@ void __init at91_add_device_serial(void) - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -+ -+ if (!atmel_default_console_device) -+ printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - #else - void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} -@@ -1060,6 +1226,7 @@ static int __init at91_add_standard_devi - { - at91_add_device_rtt(); - at91_add_device_watchdog(); -+ at91_add_device_tc(); - return 0; - } - ---- a/arch/arm/mach-at91/at91rm9200_devices.c -+++ b/arch/arm/mach-at91/at91rm9200_devices.c -@@ -513,7 +513,18 @@ void __init at91_add_device_i2c(struct i - * SPI - * -------------------------------------------------------------------- */ - --#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) -+#if defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE) /* legacy SPI driver */ -+#define SPI_DEVNAME "at91_spi" -+ -+#elif defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) /* SPI bitbanging driver */ -+#define SPI_DEVNAME "at91_spi" -+ -+#elif defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) /* new SPI driver */ -+#define SPI_DEVNAME "atmel_spi" -+ -+#endif -+ -+#ifdef SPI_DEVNAME - static u64 spi_dmamask = DMA_BIT_MASK(32); - - static struct resource spi_resources[] = { -@@ -530,7 +541,7 @@ static struct resource spi_resources[] = - }; - - static struct platform_device at91rm9200_spi_device = { -- .name = "atmel_spi", -+ .name = SPI_DEVNAME, - .id = 0, - .dev = { - .dma_mask = &spi_dmamask, -@@ -563,6 +574,12 @@ void __init at91_add_device_spi(struct s - else - at91_set_gpio_output(cs_pin, 1); - -+#if defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE) -+ /* -+ * Force peripheral mode when using the legacy SPI driver. -+ */ -+ at91_set_A_periph(cs_pin, 0); -+#endif - - /* pass chip-select pin to driver */ - devices[i].controller_data = (void *) cs_pin; -@@ -577,6 +594,90 @@ void __init at91_add_device_spi(struct s - - - /* -------------------------------------------------------------------- -+ * Timer/Counter blocks -+ * -------------------------------------------------------------------- */ -+ -+#ifdef CONFIG_ATMEL_TCLIB -+ -+static struct resource tcb0_resources[] = { -+ [0] = { -+ .start = AT91RM9200_BASE_TCB0, -+ .end = AT91RM9200_BASE_TCB0 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91RM9200_ID_TC0, -+ .end = AT91RM9200_ID_TC0, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [2] = { -+ .start = AT91RM9200_ID_TC1, -+ .end = AT91RM9200_ID_TC1, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [3] = { -+ .start = AT91RM9200_ID_TC2, -+ .end = AT91RM9200_ID_TC2, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91rm9200_tcb0_device = { -+ .name = "atmel_tcb", -+ .id = 0, -+ .resource = tcb0_resources, -+ .num_resources = ARRAY_SIZE(tcb0_resources), -+}; -+ -+static struct resource tcb1_resources[] = { -+ [0] = { -+ .start = AT91RM9200_BASE_TCB1, -+ .end = AT91RM9200_BASE_TCB1 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91RM9200_ID_TC3, -+ .end = AT91RM9200_ID_TC3, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [2] = { -+ .start = AT91RM9200_ID_TC4, -+ .end = AT91RM9200_ID_TC4, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [3] = { -+ .start = AT91RM9200_ID_TC5, -+ .end = AT91RM9200_ID_TC5, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91rm9200_tcb1_device = { -+ .name = "atmel_tcb", -+ .id = 1, -+ .resource = tcb1_resources, -+ .num_resources = ARRAY_SIZE(tcb1_resources), -+}; -+ -+static void __init at91_add_device_tc(void) -+{ -+ /* this chip has a separate clock and irq for each TC channel */ -+ at91_clock_associate("tc0_clk", &at91rm9200_tcb0_device.dev, "t0_clk"); -+ at91_clock_associate("tc1_clk", &at91rm9200_tcb0_device.dev, "t1_clk"); -+ at91_clock_associate("tc2_clk", &at91rm9200_tcb0_device.dev, "t2_clk"); -+ platform_device_register(&at91rm9200_tcb0_device); -+ -+ at91_clock_associate("tc3_clk", &at91rm9200_tcb1_device.dev, "t0_clk"); -+ at91_clock_associate("tc4_clk", &at91rm9200_tcb1_device.dev, "t1_clk"); -+ at91_clock_associate("tc5_clk", &at91rm9200_tcb1_device.dev, "t2_clk"); -+ platform_device_register(&at91rm9200_tcb1_device); -+} -+#else -+static void __init at91_add_device_tc(void) { } -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * RTC - * -------------------------------------------------------------------- */ - -@@ -589,6 +690,7 @@ static struct platform_device at91rm9200 - - static void __init at91_add_device_rtc(void) - { -+ device_init_wakeup(&at91rm9200_rtc_device.dev, 1); - platform_device_register(&at91rm9200_rtc_device); - } - #else -@@ -1019,7 +1121,7 @@ static inline void configure_usart3_pins - at91_set_B_periph(AT91_PIN_PB0, 0); /* RTS3 */ - } - --static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ - struct platform_device *atmel_default_console_device; /* the serial console device */ - - void __init __deprecated at91_init_serial(struct at91_uart_config *config) -@@ -1110,8 +1212,6 @@ void __init at91_set_serial_console(unsi - { - if (portnr < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[portnr]; -- if (!atmel_default_console_device) -- printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - - void __init at91_add_device_serial(void) -@@ -1122,6 +1222,9 @@ void __init at91_add_device_serial(void) - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -+ -+ if (!atmel_default_console_device) -+ printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - #else - void __init __deprecated at91_init_serial(struct at91_uart_config *config) {} -@@ -1141,6 +1244,7 @@ static int __init at91_add_standard_devi - { - at91_add_device_rtc(); - at91_add_device_watchdog(); -+ at91_add_device_tc(); - return 0; - } - ---- a/arch/arm/mach-at91/at91rm9200_time.c -+++ b/arch/arm/mach-at91/at91rm9200_time.c -@@ -136,8 +136,6 @@ clkevt32k_next_event(unsigned long delta - u32 alm; - int status = 0; - -- BUG_ON(delta < 2); -- - /* Use "raw" primitives so we behave correctly on RT kernels. */ - raw_local_irq_save(flags); - ---- a/arch/arm/mach-at91/at91sam9260.c -+++ b/arch/arm/mach-at91/at91sam9260.c -@@ -11,6 +11,7 @@ - */ - - #include <linux/module.h> -+#include <linux/pm.h> - - #include <asm/mach/arch.h> - #include <asm/mach/map.h> -@@ -18,6 +19,7 @@ - #include <asm/arch/at91sam9260.h> - #include <asm/arch/at91_pmc.h> - #include <asm/arch/at91_rstc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - #include "clock.h" -@@ -267,6 +269,11 @@ static void at91sam9260_reset(void) - at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); - } - -+static void at91sam9260_poweroff(void) -+{ -+ at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -+} -+ - - /* -------------------------------------------------------------------- - * AT91SAM9260 processor initialization -@@ -304,6 +311,7 @@ void __init at91sam9260_initialize(unsig - iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc)); - - at91_arch_reset = at91sam9260_reset; -+ pm_power_off = at91sam9260_poweroff; - at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1) - | (1 << AT91SAM9260_ID_IRQ2); - ---- a/arch/arm/mach-at91/at91sam9260_devices.c -+++ b/arch/arm/mach-at91/at91sam9260_devices.c -@@ -19,8 +19,8 @@ - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> - #include <asm/arch/at91sam9260.h> --#include <asm/arch/at91sam926x_mc.h> - #include <asm/arch/at91sam9260_matrix.h> -+#include <asm/arch/at91sam9_smc.h> - - #include "generic.h" - -@@ -288,10 +288,15 @@ static struct at91_nand_data nand_data; - #define NAND_BASE AT91_CHIPSELECT_3 - - static struct resource nand_resources[] = { -- { -+ [0] = { - .start = NAND_BASE, - .end = NAND_BASE + SZ_256M - 1, - .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91_BASE_SYS + AT91_ECC, -+ .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1, -+ .flags = IORESOURCE_MEM, - } - }; - -@@ -540,6 +545,90 @@ void __init at91_add_device_spi(struct s - - - /* -------------------------------------------------------------------- -+ * Timer/Counter blocks -+ * -------------------------------------------------------------------- */ -+ -+#ifdef CONFIG_ATMEL_TCLIB -+ -+static struct resource tcb0_resources[] = { -+ [0] = { -+ .start = AT91SAM9260_BASE_TCB0, -+ .end = AT91SAM9260_BASE_TCB0 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91SAM9260_ID_TC0, -+ .end = AT91SAM9260_ID_TC0, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [2] = { -+ .start = AT91SAM9260_ID_TC1, -+ .end = AT91SAM9260_ID_TC1, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [3] = { -+ .start = AT91SAM9260_ID_TC2, -+ .end = AT91SAM9260_ID_TC2, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91sam9260_tcb0_device = { -+ .name = "atmel_tcb", -+ .id = 0, -+ .resource = tcb0_resources, -+ .num_resources = ARRAY_SIZE(tcb0_resources), -+}; -+ -+static struct resource tcb1_resources[] = { -+ [0] = { -+ .start = AT91SAM9260_BASE_TCB1, -+ .end = AT91SAM9260_BASE_TCB1 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91SAM9260_ID_TC3, -+ .end = AT91SAM9260_ID_TC3, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [2] = { -+ .start = AT91SAM9260_ID_TC4, -+ .end = AT91SAM9260_ID_TC4, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [3] = { -+ .start = AT91SAM9260_ID_TC5, -+ .end = AT91SAM9260_ID_TC5, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91sam9260_tcb1_device = { -+ .name = "atmel_tcb", -+ .id = 1, -+ .resource = tcb1_resources, -+ .num_resources = ARRAY_SIZE(tcb1_resources), -+}; -+ -+static void __init at91_add_device_tc(void) -+{ -+ /* this chip has a separate clock and irq for each TC channel */ -+ at91_clock_associate("tc0_clk", &at91sam9260_tcb0_device.dev, "t0_clk"); -+ at91_clock_associate("tc1_clk", &at91sam9260_tcb0_device.dev, "t1_clk"); -+ at91_clock_associate("tc2_clk", &at91sam9260_tcb0_device.dev, "t2_clk"); -+ platform_device_register(&at91sam9260_tcb0_device); -+ -+ at91_clock_associate("tc3_clk", &at91sam9260_tcb1_device.dev, "t0_clk"); -+ at91_clock_associate("tc4_clk", &at91sam9260_tcb1_device.dev, "t1_clk"); -+ at91_clock_associate("tc5_clk", &at91sam9260_tcb1_device.dev, "t2_clk"); -+ platform_device_register(&at91sam9260_tcb1_device); -+} -+#else -+static void __init at91_add_device_tc(void) { } -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * RTT - * -------------------------------------------------------------------- */ - -@@ -553,13 +642,14 @@ static struct resource rtt_resources[] = - - static struct platform_device at91sam9260_rtt_device = { - .name = "at91_rtt", -- .id = -1, -+ .id = 0, - .resource = rtt_resources, - .num_resources = ARRAY_SIZE(rtt_resources), - }; - - static void __init at91_add_device_rtt(void) - { -+ device_init_wakeup(&at91sam9260_rtt_device.dev, 1); - platform_device_register(&at91sam9260_rtt_device); - } - -@@ -962,7 +1052,7 @@ static inline void configure_usart5_pins - at91_set_A_periph(AT91_PIN_PB13, 0); /* RXD5 */ - } - --static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ - struct platform_device *atmel_default_console_device; /* the serial console device */ - - void __init __deprecated at91_init_serial(struct at91_uart_config *config) -@@ -1073,8 +1163,6 @@ void __init at91_set_serial_console(unsi - { - if (portnr < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[portnr]; -- if (!atmel_default_console_device) -- printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - - void __init at91_add_device_serial(void) -@@ -1085,6 +1173,9 @@ void __init at91_add_device_serial(void) - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -+ -+ if (!atmel_default_console_device) -+ printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - #else - void __init __deprecated at91_init_serial(struct at91_uart_config *config) {} -@@ -1103,6 +1194,7 @@ static int __init at91_add_standard_devi - { - at91_add_device_rtt(); - at91_add_device_watchdog(); -+ at91_add_device_tc(); - return 0; - } - ---- a/arch/arm/mach-at91/at91sam9261.c -+++ b/arch/arm/mach-at91/at91sam9261.c -@@ -11,12 +11,14 @@ - */ - - #include <linux/module.h> -+#include <linux/pm.h> - - #include <asm/mach/arch.h> - #include <asm/mach/map.h> - #include <asm/arch/at91sam9261.h> - #include <asm/arch/at91_pmc.h> - #include <asm/arch/at91_rstc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - #include "clock.h" -@@ -245,6 +247,11 @@ static void at91sam9261_reset(void) - at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); - } - -+static void at91sam9261_poweroff(void) -+{ -+ at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -+} -+ - - /* -------------------------------------------------------------------- - * AT91SAM9261 processor initialization -@@ -256,6 +263,7 @@ void __init at91sam9261_initialize(unsig - iotable_init(at91sam9261_io_desc, ARRAY_SIZE(at91sam9261_io_desc)); - - at91_arch_reset = at91sam9261_reset; -+ pm_power_off = at91sam9261_poweroff; - at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1) - | (1 << AT91SAM9261_ID_IRQ2); - ---- a/arch/arm/mach-at91/at91sam9261_devices.c -+++ b/arch/arm/mach-at91/at91sam9261_devices.c -@@ -24,7 +24,7 @@ - #include <asm/arch/gpio.h> - #include <asm/arch/at91sam9261.h> - #include <asm/arch/at91sam9261_matrix.h> --#include <asm/arch/at91sam926x_mc.h> -+#include <asm/arch/at91sam9_smc.h> - - #include "generic.h" - -@@ -548,6 +548,55 @@ void __init at91_add_device_lcdc(struct - - - /* -------------------------------------------------------------------- -+ * Timer/Counter block -+ * -------------------------------------------------------------------- */ -+ -+#ifdef CONFIG_ATMEL_TCLIB -+ -+static struct resource tcb_resources[] = { -+ [0] = { -+ .start = AT91SAM9261_BASE_TCB0, -+ .end = AT91SAM9261_BASE_TCB0 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91SAM9261_ID_TC0, -+ .end = AT91SAM9261_ID_TC0, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [2] = { -+ .start = AT91SAM9261_ID_TC1, -+ .end = AT91SAM9261_ID_TC1, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [3] = { -+ .start = AT91SAM9261_ID_TC2, -+ .end = AT91SAM9261_ID_TC2, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91sam9261_tcb_device = { -+ .name = "atmel_tcb", -+ .id = 0, -+ .resource = tcb_resources, -+ .num_resources = ARRAY_SIZE(tcb_resources), -+}; -+ -+static void __init at91_add_device_tc(void) -+{ -+ /* this chip has a separate clock and irq for each TC channel */ -+ at91_clock_associate("tc0_clk", &at91sam9261_tcb_device.dev, "t0_clk"); -+ at91_clock_associate("tc1_clk", &at91sam9261_tcb_device.dev, "t1_clk"); -+ at91_clock_associate("tc2_clk", &at91sam9261_tcb_device.dev, "t2_clk"); -+ platform_device_register(&at91sam9261_tcb_device); -+} -+#else -+static void __init at91_add_device_tc(void) { } -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * RTT - * -------------------------------------------------------------------- */ - -@@ -561,13 +610,14 @@ static struct resource rtt_resources[] = - - static struct platform_device at91sam9261_rtt_device = { - .name = "at91_rtt", -- .id = -1, -+ .id = 0, - .resource = rtt_resources, - .num_resources = ARRAY_SIZE(rtt_resources), - }; - - static void __init at91_add_device_rtt(void) - { -+ device_init_wakeup(&at91sam9261_rtt_device.dev, 1); - platform_device_register(&at91sam9261_rtt_device); - } - -@@ -938,7 +988,7 @@ static inline void configure_usart2_pins - at91_set_B_periph(AT91_PIN_PA16, 0); /* CTS2 */ - } - --static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ - struct platform_device *atmel_default_console_device; /* the serial console device */ - - void __init __deprecated at91_init_serial(struct at91_uart_config *config) -@@ -1019,8 +1069,6 @@ void __init at91_set_serial_console(unsi - { - if (portnr < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[portnr]; -- if (!atmel_default_console_device) -- printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - - void __init at91_add_device_serial(void) -@@ -1031,6 +1079,9 @@ void __init at91_add_device_serial(void) - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -+ -+ if (!atmel_default_console_device) -+ printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - #else - void __init __deprecated at91_init_serial(struct at91_uart_config *config) {} -@@ -1050,6 +1101,7 @@ static int __init at91_add_standard_devi - { - at91_add_device_rtt(); - at91_add_device_watchdog(); -+ at91_add_device_tc(); - return 0; - } - ---- a/arch/arm/mach-at91/at91sam9263.c -+++ b/arch/arm/mach-at91/at91sam9263.c -@@ -11,12 +11,14 @@ - */ - - #include <linux/module.h> -+#include <linux/pm.h> - - #include <asm/mach/arch.h> - #include <asm/mach/map.h> - #include <asm/arch/at91sam9263.h> - #include <asm/arch/at91_pmc.h> - #include <asm/arch/at91_rstc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - #include "clock.h" -@@ -271,6 +273,11 @@ static void at91sam9263_reset(void) - at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); - } - -+static void at91sam9263_poweroff(void) -+{ -+ at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -+} -+ - - /* -------------------------------------------------------------------- - * AT91SAM9263 processor initialization -@@ -282,6 +289,7 @@ void __init at91sam9263_initialize(unsig - iotable_init(at91sam9263_io_desc, ARRAY_SIZE(at91sam9263_io_desc)); - - at91_arch_reset = at91sam9263_reset; -+ pm_power_off = at91sam9263_poweroff; - at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1); - - /* Init clock subsystem */ ---- a/arch/arm/mach-at91/at91sam9263_devices.c -+++ b/arch/arm/mach-at91/at91sam9263_devices.c -@@ -22,8 +22,8 @@ - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> - #include <asm/arch/at91sam9263.h> --#include <asm/arch/at91sam926x_mc.h> - #include <asm/arch/at91sam9263_matrix.h> -+#include <asm/arch/at91sam9_smc.h> - - #include "generic.h" - -@@ -308,7 +308,7 @@ void __init at91_add_device_mmc(short mm - } - - mmc0_data = *data; -- at91_clock_associate("mci0_clk", &at91sam9263_mmc1_device.dev, "mci_clk"); -+ at91_clock_associate("mci0_clk", &at91sam9263_mmc0_device.dev, "mci_clk"); - platform_device_register(&at91sam9263_mmc0_device); - } else { /* MCI1 */ - /* CLK */ -@@ -358,10 +358,15 @@ static struct at91_nand_data nand_data; - #define NAND_BASE AT91_CHIPSELECT_3 - - static struct resource nand_resources[] = { -- { -+ [0] = { - .start = NAND_BASE, - .end = NAND_BASE + SZ_256M - 1, - .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91_BASE_SYS + AT91_ECC0, -+ .end = AT91_BASE_SYS + AT91_ECC0 + SZ_512 - 1, -+ .flags = IORESOURCE_MEM, - } - }; - -@@ -783,6 +788,43 @@ void __init at91_add_device_isi(void) {} - - - /* -------------------------------------------------------------------- -+ * Timer/Counter block -+ * -------------------------------------------------------------------- */ -+ -+#ifdef CONFIG_ATMEL_TCLIB -+ -+static struct resource tcb_resources[] = { -+ [0] = { -+ .start = AT91SAM9263_BASE_TCB0, -+ .end = AT91SAM9263_BASE_TCB0 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91SAM9263_ID_TCB, -+ .end = AT91SAM9263_ID_TCB, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91sam9263_tcb_device = { -+ .name = "atmel_tcb", -+ .id = 0, -+ .resource = tcb_resources, -+ .num_resources = ARRAY_SIZE(tcb_resources), -+}; -+ -+static void __init at91_add_device_tc(void) -+{ -+ /* this chip has one clock and irq for all three TC channels */ -+ at91_clock_associate("tcb_clk", &at91sam9263_tcb_device.dev, "t0_clk"); -+ platform_device_register(&at91sam9263_tcb_device); -+} -+#else -+static void __init at91_add_device_tc(void) { } -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * RTT - * -------------------------------------------------------------------- */ - -@@ -818,7 +860,9 @@ static struct platform_device at91sam926 - - static void __init at91_add_device_rtt(void) - { -+ device_init_wakeup(&at91sam9263_rtt0_device.dev, 1); - platform_device_register(&at91sam9263_rtt0_device); -+ device_init_wakeup(&at91sam9263_rtt1_device.dev, 1); - platform_device_register(&at91sam9263_rtt1_device); - } - -@@ -933,9 +977,6 @@ static inline void configure_ssc1_pins(u - } - - /* -- * Return the device node so that board init code can use it as the -- * parent for the device node reflecting how it's used on this board. -- * - * SSC controllers are accessed through library code, instead of any - * kind of all-singing/all-dancing driver. For example one could be - * used by a particular I2S audio codec's driver, while another one -@@ -1146,7 +1187,7 @@ static inline void configure_usart2_pins - at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */ - } - --static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ - struct platform_device *atmel_default_console_device; /* the serial console device */ - - void __init __deprecated at91_init_serial(struct at91_uart_config *config) -@@ -1227,8 +1268,6 @@ void __init at91_set_serial_console(unsi - { - if (portnr < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[portnr]; -- if (!atmel_default_console_device) -- printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - - void __init at91_add_device_serial(void) -@@ -1239,9 +1278,12 @@ void __init at91_add_device_serial(void) - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -+ -+ if (!atmel_default_console_device) -+ printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - #else --void __init at91_init_serial(struct at91_uart_config *config) {} -+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {} - void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {} - void __init at91_set_serial_console(unsigned portnr) {} - void __init at91_add_device_serial(void) {} -@@ -1257,6 +1299,7 @@ static int __init at91_add_standard_devi - { - at91_add_device_rtt(); - at91_add_device_watchdog(); -+ at91_add_device_tc(); - return 0; - } - ---- a/arch/arm/mach-at91/at91sam926x_time.c -+++ b/arch/arm/mach-at91/at91sam926x_time.c -@@ -1,23 +1,20 @@ - /* -- * linux/arch/arm/mach-at91/at91sam926x_time.c -+ * at91sam926x_time.c - Periodic Interval Timer (PIT) for at91sam926x - * - * Copyright (C) 2005-2006 M. Amine SAYA, ATMEL Rousset, France - * Revision 2005 M. Nicolas Diremdjian, ATMEL Rousset, France -+ * Converted to ClockSource/ClockEvents by David Brownell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -- --#include <linux/init.h> - #include <linux/interrupt.h> - #include <linux/irq.h> - #include <linux/kernel.h> --#include <linux/sched.h> --#include <linux/time.h> -+#include <linux/clk.h> -+#include <linux/clockchips.h> - --#include <asm/hardware.h> --#include <asm/io.h> - #include <asm/mach/time.h> - - #include <asm/arch/at91_pit.h> -@@ -26,85 +23,167 @@ - #define PIT_CPIV(x) ((x) & AT91_PIT_CPIV) - #define PIT_PICNT(x) (((x) & AT91_PIT_PICNT) >> 20) - -+static u32 pit_cycle; /* write-once */ -+static u32 pit_cnt; /* access only w/system irq blocked */ -+ -+ - /* -- * Returns number of microseconds since last timer interrupt. Note that interrupts -- * will have been disabled by do_gettimeofday() -- * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. -+ * Clocksource: just a monotonic counter of MCK/16 cycles. -+ * We don't care whether or not PIT irqs are enabled. - */ --static unsigned long at91sam926x_gettimeoffset(void) -+static cycle_t read_pit_clk(void) - { -- unsigned long elapsed; -- unsigned long t = at91_sys_read(AT91_PIT_PIIR); -+ unsigned long flags; -+ u32 elapsed; -+ u32 t; -+ -+ raw_local_irq_save(flags); -+ elapsed = pit_cnt; -+ t = at91_sys_read(AT91_PIT_PIIR); -+ raw_local_irq_restore(flags); -+ -+ elapsed += PIT_PICNT(t) * pit_cycle; -+ elapsed += PIT_CPIV(t); -+ return elapsed; -+} -+ -+static struct clocksource pit_clk = { -+ .name = "pit", -+ .rating = 175, -+ .read = read_pit_clk, -+ .shift = 20, -+ .flags = CLOCK_SOURCE_IS_CONTINUOUS, -+}; -+ - -- elapsed = (PIT_PICNT(t) * LATCH) + PIT_CPIV(t); /* hardware clock cycles */ -+/* -+ * Clockevent device: interrupts every 1/HZ (== pit_cycles * MCK/16) -+ */ -+static void -+pit_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev) -+{ -+ unsigned long flags; - -- return (unsigned long)(elapsed * jiffies_to_usecs(1)) / LATCH; -+ switch (mode) { -+ case CLOCK_EVT_MODE_PERIODIC: -+ /* update clocksource counter, then enable the IRQ */ -+ raw_local_irq_save(flags); -+ pit_cnt += pit_cycle * PIT_PICNT(at91_sys_read(AT91_PIT_PIVR)); -+ at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN -+ | AT91_PIT_PITIEN); -+ raw_local_irq_restore(flags); -+ break; -+ case CLOCK_EVT_MODE_ONESHOT: -+ BUG(); -+ /* FALLTHROUGH */ -+ case CLOCK_EVT_MODE_SHUTDOWN: -+ case CLOCK_EVT_MODE_UNUSED: -+ /* disable irq, leaving the clocksource active */ -+ at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN); -+ break; -+ case CLOCK_EVT_MODE_RESUME: -+ break; -+ } - } - -+static struct clock_event_device pit_clkevt = { -+ .name = "pit", -+ .features = CLOCK_EVT_FEAT_PERIODIC, -+ .shift = 32, -+ .rating = 100, -+ .cpumask = CPU_MASK_CPU0, -+ .set_mode = pit_clkevt_mode, -+}; -+ -+ - /* - * IRQ handler for the timer. - */ --static irqreturn_t at91sam926x_timer_interrupt(int irq, void *dev_id) -+static irqreturn_t at91sam926x_pit_interrupt(int irq, void *dev_id) - { -- volatile long nr_ticks; - -- if (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS) { /* This is a shared interrupt */ -- /* Get number to ticks performed before interrupt and clear PIT interrupt */ -+ /* The PIT interrupt may be disabled, and is shared */ -+ if ((pit_clkevt.mode == CLOCK_EVT_MODE_PERIODIC) -+ && (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS)) { -+ unsigned nr_ticks; -+ -+ /* Get number of ticks performed before irq, and ack it */ - nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR)); - do { -- timer_tick(); -+ pit_cnt += pit_cycle; -+ pit_clkevt.event_handler(&pit_clkevt); - nr_ticks--; - } while (nr_ticks); - - return IRQ_HANDLED; -- } else -- return IRQ_NONE; /* not handled */ -+ } -+ -+ return IRQ_NONE; - } - --static struct irqaction at91sam926x_timer_irq = { -+static struct irqaction at91sam926x_pit_irq = { - .name = "at91_tick", - .flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, -- .handler = at91sam926x_timer_interrupt -+ .handler = at91sam926x_pit_interrupt - }; - --void at91sam926x_timer_reset(void) -+static void at91sam926x_pit_reset(void) - { -- /* Disable timer */ -+ /* Disable timer and irqs */ - at91_sys_write(AT91_PIT_MR, 0); - -- /* Clear any pending interrupts */ -- (void) at91_sys_read(AT91_PIT_PIVR); -+ /* Clear any pending interrupts, wait for PIT to stop counting */ -+ while (PIT_CPIV(at91_sys_read(AT91_PIT_PIVR)) != 0) -+ cpu_relax(); - -- /* Set Period Interval timer and enable its interrupt */ -- at91_sys_write(AT91_PIT_MR, (LATCH & AT91_PIT_PIV) | AT91_PIT_PITIEN | AT91_PIT_PITEN); -+ /* Start PIT but don't enable IRQ */ -+ at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN); - } - - /* -- * Set up timer interrupt. -+ * Set up both clocksource and clockevent support. - */ --void __init at91sam926x_timer_init(void) -+static void __init at91sam926x_pit_init(void) - { -+ unsigned long pit_rate; -+ unsigned bits; -+ -+ /* -+ * Use our actual MCK to figure out how many MCK/16 ticks per -+ * 1/HZ period (instead of a compile-time constant LATCH). -+ */ -+ pit_rate = clk_get_rate(clk_get(NULL, "mck")) / 16; -+ pit_cycle = (pit_rate + HZ/2) / HZ; -+ WARN_ON(((pit_cycle - 1) & ~AT91_PIT_PIV) != 0); -+ - /* Initialize and enable the timer */ -- at91sam926x_timer_reset(); -+ at91sam926x_pit_reset(); - -- /* Make IRQs happen for the system timer. */ -- setup_irq(AT91_ID_SYS, &at91sam926x_timer_irq); -+ /* -+ * Register clocksource. The high order bits of PIV are unused, -+ * so this isn't a 32-bit counter unless we get clockevent irqs. -+ */ -+ pit_clk.mult = clocksource_hz2mult(pit_rate, pit_clk.shift); -+ bits = 12 /* PICNT */ + ilog2(pit_cycle) /* PIV */; -+ pit_clk.mask = CLOCKSOURCE_MASK(bits); -+ clocksource_register(&pit_clk); -+ -+ /* Set up irq handler */ -+ setup_irq(AT91_ID_SYS, &at91sam926x_pit_irq); -+ -+ /* Set up and register clockevents */ -+ pit_clkevt.mult = div_sc(pit_rate, NSEC_PER_SEC, pit_clkevt.shift); -+ clockevents_register_device(&pit_clkevt); - } - --#ifdef CONFIG_PM --static void at91sam926x_timer_suspend(void) -+static void at91sam926x_pit_suspend(void) - { - /* Disable timer */ - at91_sys_write(AT91_PIT_MR, 0); - } --#else --#define at91sam926x_timer_suspend NULL --#endif - - struct sys_timer at91sam926x_timer = { -- .init = at91sam926x_timer_init, -- .offset = at91sam926x_gettimeoffset, -- .suspend = at91sam926x_timer_suspend, -- .resume = at91sam926x_timer_reset, -+ .init = at91sam926x_pit_init, -+ .suspend = at91sam926x_pit_suspend, -+ .resume = at91sam926x_pit_reset, - }; -- ---- a/arch/arm/mach-at91/at91sam9rl.c -+++ b/arch/arm/mach-at91/at91sam9rl.c -@@ -10,6 +10,7 @@ - */ - - #include <linux/module.h> -+#include <linux/pm.h> - - #include <asm/mach/arch.h> - #include <asm/mach/map.h> -@@ -17,6 +18,7 @@ - #include <asm/arch/at91sam9rl.h> - #include <asm/arch/at91_pmc.h> - #include <asm/arch/at91_rstc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - #include "clock.h" -@@ -244,6 +246,11 @@ static void at91sam9rl_reset(void) - at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); - } - -+static void at91sam9rl_poweroff(void) -+{ -+ at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -+} -+ - - /* -------------------------------------------------------------------- - * AT91SAM9RL processor initialization -@@ -274,6 +281,7 @@ void __init at91sam9rl_initialize(unsign - iotable_init(at91sam9rl_sram_desc, ARRAY_SIZE(at91sam9rl_sram_desc)); - - at91_arch_reset = at91sam9rl_reset; -+ pm_power_off = at91sam9rl_poweroff; - at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0); - - /* Init clock subsystem */ ---- a/arch/arm/mach-at91/at91sam9rl_devices.c -+++ b/arch/arm/mach-at91/at91sam9rl_devices.c -@@ -20,12 +20,107 @@ - #include <asm/arch/gpio.h> - #include <asm/arch/at91sam9rl.h> - #include <asm/arch/at91sam9rl_matrix.h> --#include <asm/arch/at91sam926x_mc.h> -+#include <asm/arch/at91sam9_smc.h> - - #include "generic.h" - - - /* -------------------------------------------------------------------- -+ * USB HS Device (Gadget) -+ * -------------------------------------------------------------------- */ -+ -+#if defined(CONFIG_USB_GADGET_ATMEL_USBA) || defined(CONFIG_USB_GADGET_ATMEL_USBA_MODULE) -+ -+static struct resource usba_udc_resources[] = { -+ [0] = { -+ .start = AT91SAM9RL_UDPHS_FIFO, -+ .end = AT91SAM9RL_UDPHS_FIFO + SZ_512K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91SAM9RL_BASE_UDPHS, -+ .end = AT91SAM9RL_BASE_UDPHS + SZ_1K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [2] = { -+ .start = AT91SAM9RL_ID_UDPHS, -+ .end = AT91SAM9RL_ID_UDPHS, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \ -+ [idx] = { \ -+ .name = nam, \ -+ .index = idx, \ -+ .fifo_size = maxpkt, \ -+ .nr_banks = maxbk, \ -+ .can_dma = dma, \ -+ .can_isoc = isoc, \ -+ } -+ -+static struct usba_ep_data usba_udc_ep[] __initdata = { -+ EP("ep0", 0, 64, 1, 0, 0), -+ EP("ep1", 1, 1024, 2, 1, 1), -+ EP("ep2", 2, 1024, 2, 1, 1), -+ EP("ep3", 3, 1024, 3, 1, 0), -+ EP("ep4", 4, 1024, 3, 1, 0), -+ EP("ep5", 5, 1024, 3, 1, 1), -+ EP("ep6", 6, 1024, 3, 1, 1), -+}; -+ -+#undef EP -+ -+/* -+ * pdata doesn't have room for any endpoints, so we need to -+ * append room for the ones we need right after it. -+ */ -+static struct { -+ struct usba_platform_data pdata; -+ struct usba_ep_data ep[7]; -+} usba_udc_data; -+ -+static struct platform_device at91_usba_udc_device = { -+ .name = "atmel_usba_udc", -+ .id = -1, -+ .dev = { -+ .platform_data = &usba_udc_data.pdata, -+ }, -+ .resource = usba_udc_resources, -+ .num_resources = ARRAY_SIZE(usba_udc_resources), -+}; -+ -+void __init at91_add_device_usba(struct usba_platform_data *data) -+{ -+ /* -+ * Invalid pins are 0 on AT91, but the usba driver is shared -+ * with AVR32, which use negative values instead. Once/if -+ * gpio_is_valid() is ported to AT91, revisit this code. -+ */ -+ usba_udc_data.pdata.vbus_pin = -EINVAL; -+ usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep); -+ memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));; -+ -+ if (data && data->vbus_pin > 0) { -+ at91_set_gpio_input(data->vbus_pin, 0); -+ at91_set_deglitch(data->vbus_pin, 1); -+ usba_udc_data.pdata.vbus_pin = data->vbus_pin; -+ } -+ -+ /* Pullup pin is handled internally by USB device peripheral */ -+ -+ /* Clocks */ -+ at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk"); -+ at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk"); -+ -+ platform_device_register(&at91_usba_udc_device); -+} -+#else -+void __init at91_add_device_usba(struct usba_platform_data *data) {} -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * MMC / SD - * -------------------------------------------------------------------- */ - -@@ -105,10 +200,15 @@ static struct at91_nand_data nand_data; - #define NAND_BASE AT91_CHIPSELECT_3 - - static struct resource nand_resources[] = { -- { -+ [0] = { - .start = NAND_BASE, - .end = NAND_BASE + SZ_256M - 1, - .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91_BASE_SYS + AT91_ECC, -+ .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1, -+ .flags = IORESOURCE_MEM, - } - }; - -@@ -385,6 +485,100 @@ void __init at91_add_device_lcdc(struct - - - /* -------------------------------------------------------------------- -+ * Timer/Counter block -+ * -------------------------------------------------------------------- */ -+ -+#ifdef CONFIG_ATMEL_TCLIB -+ -+static struct resource tcb_resources[] = { -+ [0] = { -+ .start = AT91SAM9RL_BASE_TCB0, -+ .end = AT91SAM9RL_BASE_TCB0 + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91SAM9RL_ID_TC0, -+ .end = AT91SAM9RL_ID_TC0, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [2] = { -+ .start = AT91SAM9RL_ID_TC1, -+ .end = AT91SAM9RL_ID_TC1, -+ .flags = IORESOURCE_IRQ, -+ }, -+ [3] = { -+ .start = AT91SAM9RL_ID_TC2, -+ .end = AT91SAM9RL_ID_TC2, -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct platform_device at91sam9rl_tcb_device = { -+ .name = "atmel_tcb", -+ .id = 0, -+ .resource = tcb_resources, -+ .num_resources = ARRAY_SIZE(tcb_resources), -+}; -+ -+static void __init at91_add_device_tc(void) -+{ -+ /* this chip has a separate clock and irq for each TC channel */ -+ at91_clock_associate("tc0_clk", &at91sam9rl_tcb_device.dev, "t0_clk"); -+ at91_clock_associate("tc1_clk", &at91sam9rl_tcb_device.dev, "t1_clk"); -+ at91_clock_associate("tc2_clk", &at91sam9rl_tcb_device.dev, "t2_clk"); -+ platform_device_register(&at91sam9rl_tcb_device); -+} -+#else -+static void __init at91_add_device_tc(void) { } -+#endif -+ -+ -+/* -------------------------------------------------------------------- -+ * Touchscreen -+ * -------------------------------------------------------------------- */ -+ -+#if defined(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) || defined(CONFIG_TOUCHSCREEN_ATMEL_TSADCC_MODULE) -+static u64 tsadcc_dmamask = DMA_BIT_MASK(32); -+ -+static struct resource tsadcc_resources[] = { -+ [0] = { -+ .start = AT91SAM9RL_BASE_TSC, -+ .end = AT91SAM9RL_BASE_TSC + SZ_16K - 1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { -+ .start = AT91SAM9RL_ID_TSC, -+ .end = AT91SAM9RL_ID_TSC, -+ .flags = IORESOURCE_IRQ, -+ } -+}; -+ -+static struct platform_device at91_tsadcc_device = { -+ .name = "atmel_tsadcc", -+ .id = -1, -+ .dev = { -+ .dma_mask = &tsadcc_dmamask, -+ .coherent_dma_mask = DMA_BIT_MASK(32), -+ }, -+ .resource = tsadcc_resources, -+ .num_resources = ARRAY_SIZE(tsadcc_resources), -+}; -+ -+void __init at91_add_device_tsadcc(void) -+{ -+ at91_set_A_periph(AT91_PIN_PA17, 0); /* AD0_XR */ -+ at91_set_A_periph(AT91_PIN_PA18, 0); /* AD1_XL */ -+ at91_set_A_periph(AT91_PIN_PA19, 0); /* AD2_YT */ -+ at91_set_A_periph(AT91_PIN_PA20, 0); /* AD3_TB */ -+ -+ platform_device_register(&at91_tsadcc_device); -+} -+#else -+void __init at91_add_device_tsadcc(void) {} -+#endif -+ -+ -+/* -------------------------------------------------------------------- - * RTC - * -------------------------------------------------------------------- */ - -@@ -397,6 +591,7 @@ static struct platform_device at91sam9rl - - static void __init at91_add_device_rtc(void) - { -+ device_init_wakeup(&at91sam9rl_rtc_device.dev, 1); - platform_device_register(&at91sam9rl_rtc_device); - } - #else -@@ -418,13 +613,14 @@ static struct resource rtt_resources[] = - - static struct platform_device at91sam9rl_rtt_device = { - .name = "at91_rtt", -- .id = -1, -+ .id = 0, - .resource = rtt_resources, - .num_resources = ARRAY_SIZE(rtt_resources), - }; - - static void __init at91_add_device_rtt(void) - { -+ device_init_wakeup(&at91sam9rl_rtt_device.dev, 1); - platform_device_register(&at91sam9rl_rtt_device); - } - -@@ -539,9 +735,6 @@ static inline void configure_ssc1_pins(u - } - - /* -- * Return the device node so that board init code can use it as the -- * parent for the device node reflecting how it's used on this board. -- * - * SSC controllers are accessed through library code, instead of any - * kind of all-singing/all-dancing driver. For example one could be - * used by a particular I2S audio codec's driver, while another one -@@ -802,7 +995,7 @@ static inline void configure_usart3_pins - at91_set_B_periph(AT91_PIN_PD3, 0); /* CTS3 */ - } - --static struct platform_device *at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ -+static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ - struct platform_device *atmel_default_console_device; /* the serial console device */ - - void __init __deprecated at91_init_serial(struct at91_uart_config *config) -@@ -893,8 +1086,6 @@ void __init at91_set_serial_console(unsi - { - if (portnr < ATMEL_MAX_UART) - atmel_default_console_device = at91_uarts[portnr]; -- if (!atmel_default_console_device) -- printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - - void __init at91_add_device_serial(void) -@@ -905,6 +1096,9 @@ void __init at91_add_device_serial(void) - if (at91_uarts[i]) - platform_device_register(at91_uarts[i]); - } -+ -+ if (!atmel_default_console_device) -+ printk(KERN_INFO "AT91: No default serial console defined.\n"); - } - #else - void __init __deprecated at91_init_serial(struct at91_uart_config *config) {} -@@ -925,6 +1119,7 @@ static int __init at91_add_standard_devi - at91_add_device_rtc(); - at91_add_device_rtt(); - at91_add_device_watchdog(); -+ at91_add_device_tc(); - return 0; - } - ---- /dev/null -+++ b/arch/arm/mach-at91/board-cam60.c -@@ -0,0 +1,180 @@ -+/* -+ * KwikByte CAM60 (KB9260) -+ * -+ * based on board-sam9260ek.c -+ * Copyright (C) 2005 SAN People -+ * Copyright (C) 2006 Atmel -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/spi/flash.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+ -+#include "generic.h" -+ -+ -+static void __init cam60_map_io(void) -+{ -+ /* Initialize processor: 10 MHz crystal */ -+ at91sam9260_initialize(10000000); -+ -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); -+} -+ -+static void __init cam60_init_irq(void) -+{ -+ at91sam9260_init_interrupts(NULL); -+} -+ -+ -+/* -+ * USB Host -+ */ -+static struct at91_usbh_data __initdata cam60_usbh_data = { -+ .ports = 1, -+}; -+ -+ -+/* -+ * SPI devices. -+ */ -+#if defined(CONFIG_MTD_DATAFLASH) -+static struct mtd_partition __initdata cam60_spi_partitions[] = { -+ { -+ .name = "BOOT1", -+ .offset = 0, -+ .size = 4 * 1056, -+ }, -+ { -+ .name = "BOOT2", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 256 * 1056, -+ }, -+ { -+ .name = "kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 2222 * 1056, -+ }, -+ { -+ .name = "file system", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL, -+ }, -+}; -+ -+static struct flash_platform_data __initdata cam60_spi_flash_platform_data = { -+ .name = "spi_flash", -+ .parts = cam60_spi_partitions, -+ .nr_parts = ARRAY_SIZE(cam60_spi_partitions) -+}; -+#endif -+ -+static struct spi_board_info cam60_spi_devices[] = { -+#if defined(CONFIG_MTD_DATAFLASH) -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 15 * 1000 * 1000, -+ .bus_num = 0, -+ .platform_data = &cam60_spi_flash_platform_data -+ }, -+#endif -+}; -+ -+ -+/* -+ * MACB Ethernet device -+ */ -+static struct __initdata at91_eth_data cam60_macb_data = { -+ .phy_irq_pin = AT91_PIN_PB5, -+ .is_rmii = 0, -+}; -+ -+ -+/* -+ * NAND Flash -+ */ -+static struct mtd_partition __initdata cam60_nand_partition[] = { -+ { -+ .name = "nand_fs", -+ .offset = 0, -+ .size = MTDPART_SIZ_FULL, -+ }, -+}; -+ -+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -+{ -+ *num_partitions = ARRAY_SIZE(cam60_nand_partition); -+ return cam60_nand_partition; -+} -+ -+static struct at91_nand_data __initdata cam60_nand_data = { -+ .ale = 21, -+ .cle = 22, -+ // .det_pin = ... not there -+ .rdy_pin = AT91_PIN_PA9, -+ .enable_pin = AT91_PIN_PA7, -+ .partition_info = nand_partitions, -+}; -+ -+ -+static void __init cam60_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* SPI */ -+ at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices)); -+ /* Ethernet */ -+ at91_add_device_eth(&cam60_macb_data); -+ /* USB Host */ -+ /* enable USB power supply circuit */ -+ at91_set_gpio_output(AT91_PIN_PB18, 1); -+ at91_add_device_usbh(&cam60_usbh_data); -+ /* NAND */ -+ at91_add_device_nand(&cam60_nand_data); -+} -+ -+MACHINE_START(CAM60, "KwikByte CAM60") -+ /* Maintainer: KwikByte */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91sam926x_timer, -+ .map_io = cam60_map_io, -+ .init_irq = cam60_init_irq, -+ .init_machine = cam60_board_init, -+MACHINE_END ---- a/arch/arm/mach-at91/board-cap9adk.c -+++ b/arch/arm/mach-at91/board-cap9adk.c -@@ -36,16 +36,14 @@ - #include <asm/hardware.h> - #include <asm/setup.h> - #include <asm/mach-types.h> --#include <asm/irq.h> - - #include <asm/mach/arch.h> - #include <asm/mach/map.h> --#include <asm/mach/irq.h> - - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> - #include <asm/arch/at91cap9_matrix.h> --#include <asm/arch/at91sam926x_mc.h> -+#include <asm/arch/at91sam9_smc.h> - - #include "generic.h" - -@@ -78,6 +76,12 @@ static struct at91_usbh_data __initdata - .ports = 2, - }; - -+/* -+ * USB HS Device port -+ */ -+static struct usba_platform_data __initdata cap9adk_usba_udc_data = { -+ .vbus_pin = AT91_PIN_PB31, -+}; - - /* - * ADS7846 Touchscreen -@@ -130,7 +134,7 @@ static struct spi_board_info cap9adk_spi - { - .modalias = "ads7846", - .chip_select = 3, /* can be 2 or 3, depending on J2 jumper */ -- .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */ -+ .max_speed_hz = 125000 * 16, /* max sample rate * clocks per sample */ - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91_PIN_PC4, -@@ -324,8 +328,9 @@ static void __init cap9adk_board_init(vo - /* Serial */ - at91_add_device_serial(); - /* USB Host */ -- set_irq_type(AT91CAP9_ID_UHP, IRQT_HIGH); - at91_add_device_usbh(&cap9adk_usbh_data); -+ /* USB HS */ -+ at91_add_device_usba(&cap9adk_usba_udc_data); - /* SPI */ - at91_add_device_spi(cap9adk_spi_devices, ARRAY_SIZE(cap9adk_spi_devices)); - /* Touchscreen */ -@@ -341,7 +346,6 @@ static void __init cap9adk_board_init(vo - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* LCD Controller */ -- set_irq_type(AT91CAP9_ID_LCDC, IRQT_HIGH); - at91_add_device_lcdc(&cap9adk_lcdc_data); - /* AC97 */ - at91_add_device_ac97(&cap9adk_ac97_data); ---- a/arch/arm/mach-at91/board-carmeva.c -+++ b/arch/arm/mach-at91/board-carmeva.c -@@ -40,24 +40,21 @@ - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 3 = USART0 .. USART3 -- * 4 = DBGU -- */ --static struct at91_uart_config __initdata carmeva_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 2, -- .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ --}; -- - static void __init carmeva_map_io(void) - { - /* Initialize processor: 20.000 MHz crystal */ - at91rm9200_initialize(20000000, AT91RM9200_BGA); - -- /* Setup the serial ports and console */ -- at91_init_serial(&carmeva_uart_config); -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS -+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD -+ | ATMEL_UART_RI); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init carmeva_init_irq(void) -@@ -117,6 +114,30 @@ static struct spi_board_info carmeva_spi - }, - }; - -+static struct gpio_led carmeva_leds[] = { -+ { /* "user led 1", LED9 */ -+ .name = "led9", -+ .gpio = AT91_PIN_PA21, -+ .active_low = 1, -+ .default_trigger = "heartbeat", -+ }, -+ { /* "user led 2", LED10 */ -+ .name = "led10", -+ .gpio = AT91_PIN_PA25, -+ .active_low = 1, -+ }, -+ { /* "user led 3", LED11 */ -+ .name = "led11", -+ .gpio = AT91_PIN_PA26, -+ .active_low = 1, -+ }, -+ { /* "user led 4", LED12 */ -+ .name = "led12", -+ .gpio = AT91_PIN_PA18, -+ .active_low = 1, -+ } -+}; -+ - static void __init carmeva_board_init(void) - { - /* Serial */ -@@ -135,6 +156,8 @@ static void __init carmeva_board_init(vo - // at91_add_device_cf(&carmeva_cf_data); - /* MMC */ - at91_add_device_mmc(0, &carmeva_mmc_data); -+ /* LEDs */ -+ at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds)); - } - - MACHINE_START(CARMEVA, "Carmeva") ---- /dev/null -+++ b/arch/arm/mach-at91/board-chub.c -@@ -0,0 +1,132 @@ -+/* -+ * linux/arch/arm/mach-at91/board-chub.c -+ * -+ * Copyright (C) 2005 SAN People, adapted for Promwad Chub board -+ * by Kuten Ivan -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+ -+#include "generic.h" -+ -+/* -+ * Serial port configuration. -+ * 0 .. 3 = USART0 .. USART3 -+ * 4 = DBGU -+ */ -+static struct at91_uart_config __initdata chub_uart_config = { -+ .console_tty = 0, /* ttyS0 */ -+ .nr_tty = 5, -+ .tty_map = { 4, 0, 1, 2, 3 } /* ttyS0, ..., ttyS4 */ -+}; -+ -+static void __init chub_init_irq(void) -+{ -+ at91rm9200_init_interrupts(NULL); -+} -+ -+static void __init chub_map_io(void) -+{ -+ /* Initialize clocks: 18.432 MHz crystal */ -+ at91rm9200_initialize(18432000, AT91RM9200_PQFP); -+ -+ /* Setup the serial ports and console */ -+ at91_init_serial(&chub_uart_config); -+} -+ -+static struct at91_eth_data __initdata chub_eth_data = { -+ .phy_irq_pin = AT91_PIN_PB29, -+ .is_rmii = 0, -+}; -+ -+static struct mtd_partition __initdata chub_nand_partition[] = { -+ { -+ .name = "NAND Partition 1", -+ .offset = 0, -+ .size = MTDPART_SIZ_FULL, -+ }, -+}; -+ -+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -+{ -+ *num_partitions = ARRAY_SIZE(chub_nand_partition); -+ return chub_nand_partition; -+} -+ -+static struct at91_nand_data __initdata chub_nand_data = { -+ .ale = 22, -+ .cle = 21, -+ .enable_pin = AT91_PIN_PA27, -+ .partition_info = nand_partitions, -+}; -+ -+static struct spi_board_info chub_spi_devices[] = { -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 15 * 1000 * 1000, -+ }, -+}; -+ -+static void __init chub_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* I2C */ -+ at91_add_device_i2c(NULL, 0); -+ /* Ethernet */ -+ at91_add_device_eth(&chub_eth_data); -+ /* SPI */ -+ at91_add_device_spi(chub_spi_devices, ARRAY_SIZE(chub_spi_devices)); -+ /* NAND Flash */ -+ at91_add_device_nand(&chub_nand_data); -+ /* Disable write protect for NAND */ -+ at91_set_gpio_output(AT91_PIN_PB7, 1); -+ /* Power enable for 3x RS-232 and 1x RS-485 */ -+ at91_set_gpio_output(AT91_PIN_PB9, 1); -+ /* Disable write protect for FRAM */ -+ at91_set_gpio_output(AT91_PIN_PA21, 1); -+ /* Disable write protect for Dataflash */ -+ at91_set_gpio_output(AT91_PIN_PA19, 1); -+} -+ -+MACHINE_START(CHUB, "Promwad Chub") -+ /* Maintainer: Ivan Kuten AT Promwad DOT com */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91rm9200_timer, -+ .map_io = chub_map_io, -+ .init_irq = chub_init_irq, -+ .init_machine = chub_board_init, -+MACHINE_END ---- a/arch/arm/mach-at91/board-csb337.c -+++ b/arch/arm/mach-at91/board-csb337.c -@@ -61,6 +61,7 @@ static void __init csb337_map_io(void) - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); -+ at91_set_gpio_output(AT91_PIN_PB2, 1); /* third (unused) LED */ - - /* Setup the serial ports and console */ - at91_init_serial(&csb337_uart_config); -@@ -202,11 +203,11 @@ static struct platform_device csb300_but - - static void __init csb300_add_device_buttons(void) - { -- at91_set_gpio_input(AT91_PIN_PB29, 0); /* sw0 */ -+ at91_set_gpio_input(AT91_PIN_PB29, 1); /* sw0 */ - at91_set_deglitch(AT91_PIN_PB29, 1); -- at91_set_gpio_input(AT91_PIN_PB28, 0); /* sw1 */ -+ at91_set_gpio_input(AT91_PIN_PB28, 1); /* sw1 */ - at91_set_deglitch(AT91_PIN_PB28, 1); -- at91_set_gpio_input(AT91_PIN_PA21, 0); /* sw2 */ -+ at91_set_gpio_input(AT91_PIN_PA21, 1); /* sw2 */ - at91_set_deglitch(AT91_PIN_PA21, 1); - - platform_device_register(&csb300_button_device); -@@ -233,7 +234,7 @@ static struct gpio_led csb_leds[] = { - .gpio = AT91_PIN_PB0, - .active_low = 1, - .default_trigger = "ide-disk", -- }, -+ } - }; - - ---- a/arch/arm/mach-at91/board-csb637.c -+++ b/arch/arm/mach-at91/board-csb637.c -@@ -40,27 +40,16 @@ - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 3 = USART0 .. USART3 -- * 4 = DBGU -- */ --static struct at91_uart_config __initdata csb637_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 2, -- .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ --}; -- - static void __init csb637_map_io(void) - { - /* Initialize processor: 3.6864 MHz crystal */ - at91rm9200_initialize(3686400, AT91RM9200_BGA); - -- /* Setup the LEDs */ -- at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); - -- /* Setup the serial ports and console */ -- at91_init_serial(&csb637_uart_config); -+ /* make console=ttyS0 (ie, DBGU) the default */ -+ at91_set_serial_console(0); - } - - static void __init csb637_init_irq(void) -@@ -118,8 +107,19 @@ static struct platform_device csb_flash - .num_resources = ARRAY_SIZE(csb_flash_resources), - }; - -+static struct gpio_led csb_leds[] = { -+ { /* "d1", red */ -+ .name = "d1", -+ .gpio = AT91_PIN_PB2, -+ .active_low = 1, -+ .default_trigger = "heartbeat", -+ } -+}; -+ - static void __init csb637_board_init(void) - { -+ /* LED(s) */ -+ at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds)); - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ ---- a/arch/arm/mach-at91/board-dk.c -+++ b/arch/arm/mach-at91/board-dk.c -@@ -25,6 +25,7 @@ - #include <linux/init.h> - #include <linux/mm.h> - #include <linux/module.h> -+#include <linux/dma-mapping.h> - #include <linux/platform_device.h> - #include <linux/spi/spi.h> - #include <linux/mtd/physmap.h> -@@ -45,17 +46,6 @@ - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 3 = USART0 .. USART3 -- * 4 = DBGU -- */ --static struct at91_uart_config __initdata dk_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 2, -- .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ --}; -- - static void __init dk_map_io(void) - { - /* Initialize processor: 18.432 MHz crystal */ -@@ -64,8 +54,16 @@ static void __init dk_map_io(void) - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); - -- /* Setup the serial ports and console */ -- at91_init_serial(&dk_uart_config); -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS -+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD -+ | ATMEL_UART_RI); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init dk_init_irq(void) -@@ -73,6 +71,185 @@ static void __init dk_init_irq(void) - at91rm9200_init_interrupts(NULL); - } - -+#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE) -+#include <video/s1d13xxxfb.h> -+#include <asm/arch/ics1523.h> -+ -+/* EPSON S1D13806 FB */ -+#define AT91_FB_REG_BASE 0x30000000L -+#define AT91_FB_REG_SIZE 0x200 -+#define AT91_FB_VMEM_BASE 0x30200000L -+#define AT91_FB_VMEM_SIZE 0x140000L -+ -+static void dk_init_video(void) -+{ -+ /* NWAIT Signal */ -+ at91_set_A_periph(AT91_PIN_PC6, 0); -+ -+ /* Initialization of the Static Memory Controller for Chip Select 2 */ -+ at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */ -+ | AT91_SMC_WSEN | AT91_SMC_NWS_(4) /* wait states */ -+ | AT91_SMC_TDF_(1) /* float time */ -+ ); -+ -+ at91_ics1523_init(); -+} -+ -+/* CRT: (active) 640x480 60Hz (PCLK=CLKI=25.175MHz) -+ Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */ -+static const struct s1d13xxxfb_regval dk_s1dfb_initregs[] = { -+ {S1DREG_MISC, 0x00}, /* Enable Memory/Register select bit */ -+ {S1DREG_COM_DISP_MODE, 0x00}, /* disable display output */ -+ {S1DREG_GPIO_CNF0, 0x00}, -+ {S1DREG_GPIO_CNF1, 0x00}, -+ {S1DREG_GPIO_CTL0, 0x08}, -+ {S1DREG_GPIO_CTL1, 0x00}, -+ {S1DREG_CLK_CNF, 0x01}, /* no divide, MCLK source is CLKI3 0x02*/ -+ {S1DREG_LCD_CLK_CNF, 0x00}, -+ {S1DREG_CRT_CLK_CNF, 0x00}, -+ {S1DREG_MPLUG_CLK_CNF, 0x00}, -+ {S1DREG_CPU2MEM_WST_SEL, 0x01}, /* 2*period(MCLK) - 4ns > period(BCLK) */ -+ {S1DREG_SDRAM_REF_RATE, 0x03}, /* 32768 <= MCLK <= 50000 (MHz) */ -+ {S1DREG_SDRAM_TC0, 0x00}, /* MCLK source freq (MHz): */ -+ {S1DREG_SDRAM_TC1, 0x01}, /* 42 <= MCLK <= 50 */ -+ {S1DREG_MEM_CNF, 0x80}, /* SDRAM Initialization - needed before mem access */ -+ {S1DREG_PANEL_TYPE, 0x25}, /* std TFT 16bit, 8bit SCP format 2, single passive LCD */ -+ {S1DREG_MOD_RATE, 0x00}, /* toggle every FPFRAME */ -+ {S1DREG_LCD_DISP_HWIDTH, 0x4F}, /* 680 pix */ -+ {S1DREG_LCD_NDISP_HPER, 0x12}, /* 152 pix */ -+ {S1DREG_TFT_FPLINE_START, 0x01}, /* 13 pix */ -+ {S1DREG_TFT_FPLINE_PWIDTH, 0x0B}, /* 96 pix */ -+ {S1DREG_LCD_DISP_VHEIGHT0, 0xDF}, -+ {S1DREG_LCD_DISP_VHEIGHT1, 0x01}, /* 480 lines */ -+ {S1DREG_LCD_NDISP_VPER, 0x2C}, /* 44 lines */ -+ {S1DREG_TFT_FPFRAME_START, 0x0A}, /* 10 lines */ -+ {S1DREG_TFT_FPFRAME_PWIDTH, 0x01}, /* 2 lines */ -+ {S1DREG_LCD_DISP_MODE, 0x05}, /* 16 bpp */ -+ {S1DREG_LCD_MISC, 0x00}, /* dithering enabled, dual panel buffer enabled */ -+ {S1DREG_LCD_DISP_START0, 0x00}, -+ {S1DREG_LCD_DISP_START1, 0xC8}, -+ {S1DREG_LCD_DISP_START2, 0x00}, -+ {S1DREG_LCD_MEM_OFF0, 0x80}, -+ {S1DREG_LCD_MEM_OFF1, 0x02}, -+ {S1DREG_LCD_PIX_PAN, 0x00}, -+ {S1DREG_LCD_DISP_FIFO_HTC, 0x3B}, -+ {S1DREG_LCD_DISP_FIFO_LTC, 0x3C}, -+ {S1DREG_CRT_DISP_HWIDTH, 0x4F}, /* 680 pix */ -+ {S1DREG_CRT_NDISP_HPER, 0x13}, /* 160 pix */ -+ {S1DREG_CRT_HRTC_START, 0x01}, /* 13 pix */ -+ {S1DREG_CRT_HRTC_PWIDTH, 0x0B}, /* 96 pix */ -+ {S1DREG_CRT_DISP_VHEIGHT0, 0xDF}, -+ {S1DREG_CRT_DISP_VHEIGHT1, 0x01}, /* 480 lines */ -+ {S1DREG_CRT_NDISP_VPER, 0x2B}, /* 44 lines */ -+ {S1DREG_CRT_VRTC_START, 0x09}, /* 10 lines */ -+ {S1DREG_CRT_VRTC_PWIDTH, 0x01}, /* 2 lines */ -+ {S1DREG_TV_OUT_CTL, 0x10}, -+ {S1DREG_CRT_DISP_MODE, 0x05}, /* 16 bpp */ -+ {S1DREG_CRT_DISP_START0, 0x00}, -+ {S1DREG_CRT_DISP_START1, 0x00}, -+ {S1DREG_CRT_DISP_START2, 0x00}, -+ {S1DREG_CRT_MEM_OFF0, 0x80}, -+ {S1DREG_CRT_MEM_OFF1, 0x02}, -+ {S1DREG_CRT_PIX_PAN, 0x00}, -+ {S1DREG_CRT_DISP_FIFO_HTC, 0x3B}, -+ {S1DREG_CRT_DISP_FIFO_LTC, 0x3C}, -+ {S1DREG_LCD_CUR_CTL, 0x00}, /* inactive */ -+ {S1DREG_LCD_CUR_START, 0x01}, -+ {S1DREG_LCD_CUR_XPOS0, 0x00}, -+ {S1DREG_LCD_CUR_XPOS1, 0x00}, -+ {S1DREG_LCD_CUR_YPOS0, 0x00}, -+ {S1DREG_LCD_CUR_YPOS1, 0x00}, -+ {S1DREG_LCD_CUR_BCTL0, 0x00}, -+ {S1DREG_LCD_CUR_GCTL0, 0x00}, -+ {S1DREG_LCD_CUR_RCTL0, 0x00}, -+ {S1DREG_LCD_CUR_BCTL1, 0x1F}, -+ {S1DREG_LCD_CUR_GCTL1, 0x3F}, -+ {S1DREG_LCD_CUR_RCTL1, 0x1F}, -+ {S1DREG_LCD_CUR_FIFO_HTC, 0x00}, -+ {S1DREG_CRT_CUR_CTL, 0x00}, /* inactive */ -+ {S1DREG_CRT_CUR_START, 0x01}, -+ {S1DREG_CRT_CUR_XPOS0, 0x00}, -+ {S1DREG_CRT_CUR_XPOS1, 0x00}, -+ {S1DREG_CRT_CUR_YPOS0, 0x00}, -+ {S1DREG_CRT_CUR_YPOS1, 0x00}, -+ {S1DREG_CRT_CUR_BCTL0, 0x00}, -+ {S1DREG_CRT_CUR_GCTL0, 0x00}, -+ {S1DREG_CRT_CUR_RCTL0, 0x00}, -+ {S1DREG_CRT_CUR_BCTL1, 0x1F}, -+ {S1DREG_CRT_CUR_GCTL1, 0x3F}, -+ {S1DREG_CRT_CUR_RCTL1, 0x1F}, -+ {S1DREG_CRT_CUR_FIFO_HTC, 0x00}, -+ {S1DREG_BBLT_CTL0, 0x00}, -+ {S1DREG_BBLT_CTL0, 0x00}, -+ {S1DREG_BBLT_CC_EXP, 0x00}, -+ {S1DREG_BBLT_OP, 0x00}, -+ {S1DREG_BBLT_SRC_START0, 0x00}, -+ {S1DREG_BBLT_SRC_START1, 0x00}, -+ {S1DREG_BBLT_SRC_START2, 0x00}, -+ {S1DREG_BBLT_DST_START0, 0x00}, -+ {S1DREG_BBLT_DST_START1, 0x00}, -+ {S1DREG_BBLT_DST_START2, 0x00}, -+ {S1DREG_BBLT_MEM_OFF0, 0x00}, -+ {S1DREG_BBLT_MEM_OFF1, 0x00}, -+ {S1DREG_BBLT_WIDTH0, 0x00}, -+ {S1DREG_BBLT_WIDTH1, 0x00}, -+ {S1DREG_BBLT_HEIGHT0, 0x00}, -+ {S1DREG_BBLT_HEIGHT1, 0x00}, -+ {S1DREG_BBLT_BGC0, 0x00}, -+ {S1DREG_BBLT_BGC1, 0x00}, -+ {S1DREG_BBLT_FGC0, 0x00}, -+ {S1DREG_BBLT_FGC1, 0x00}, -+ {S1DREG_LKUP_MODE, 0x00}, /* LCD LUT r | LCD and CRT/TV LUT w */ -+ {S1DREG_LKUP_ADDR, 0x00}, -+ {S1DREG_PS_CNF, 0x00}, /* Power Save disable */ -+ {S1DREG_PS_STATUS, 0x02}, /* LCD Panel down, mem up */ -+ {S1DREG_CPU2MEM_WDOGT, 0x00}, -+ {S1DREG_COM_DISP_MODE, 0x02}, /* enable CRT display output */ -+}; -+ -+static struct s1d13xxxfb_pdata dk_s1dfb_pdata = { -+ .initregs = dk_s1dfb_initregs, -+ .initregssize = ARRAY_SIZE(dk_s1dfb_initregs), -+ .platform_init_video = dk_init_video, -+}; -+ -+static u64 s1dfb_dmamask = DMA_BIT_MASK(32); -+ -+static struct resource dk_s1dfb_resource[] = { -+ [0] = { /* video mem */ -+ .name = "s1d13806 memory", -+ .start = AT91_FB_VMEM_BASE, -+ .end = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { /* video registers */ -+ .name = "s1d13806 registers", -+ .start = AT91_FB_REG_BASE, -+ .end = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1, -+ .flags = IORESOURCE_MEM, -+ }, -+}; -+ -+static struct platform_device dk_s1dfb_device = { -+ .name = "s1d13806fb", -+ .id = -1, -+ .dev = { -+ .dma_mask = &s1dfb_dmamask, -+ .coherent_dma_mask = DMA_BIT_MASK(32), -+ .platform_data = &dk_s1dfb_pdata, -+ }, -+ .resource = dk_s1dfb_resource, -+ .num_resources = ARRAY_SIZE(dk_s1dfb_resource), -+}; -+ -+static void __init dk_add_device_video(void) -+{ -+ platform_device_register(&dk_s1dfb_device); -+} -+#else -+static void __init dk_add_device_video(void) {} -+#endif -+ - static struct at91_eth_data __initdata dk_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -@@ -164,7 +341,7 @@ static struct at91_nand_data __initdata - #define DK_FLASH_SIZE 0x200000 - - static struct physmap_flash_data dk_flash_data = { -- .width = 2, -+ .width = 2, - }; - - static struct resource dk_flash_resource = { -@@ -223,8 +400,12 @@ static void __init dk_board_init(void) - platform_device_register(&dk_flash); - /* LEDs */ - at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds)); -+ /* SSC (to LM4549 audio codec) */ -+ at91_add_device_ssc(AT91RM9200_ID_SSC1, ATMEL_SSC_TD | ATMEL_SSC_RX); -+ /* SSC (to SI3021 line interface) */ -+ at91_add_device_ssc(AT91RM9200_ID_SSC2, ATMEL_SSC_TD | ATMEL_SSC_TK | ATMEL_SSC_RD | ATMEL_SSC_RF); - /* VGA */ --// dk_add_device_video(); -+ dk_add_device_video(); - } - - MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK") ---- a/arch/arm/mach-at91/board-eb9200.c -+++ b/arch/arm/mach-at91/board-eb9200.c -@@ -40,24 +40,24 @@ - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 3 = USART0 .. USART3 -- * 4 = DBGU -- */ --static struct at91_uart_config __initdata eb9200_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 2, -- .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ --}; -- - static void __init eb9200_map_io(void) - { - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_BGA); - -- /* Setup the serial ports and console */ -- at91_init_serial(&eb9200_uart_config); -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS -+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD -+ | ATMEL_UART_RI); -+ -+ /* USART2 on ttyS2. (Rx, Tx) - IRDA */ -+ at91_register_uart(AT91RM9200_ID_US2, 2, 0); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init eb9200_init_irq(void) ---- /dev/null -+++ b/arch/arm/mach-at91/board-ecbat91.c -@@ -0,0 +1,178 @@ -+/* -+ * linux/arch/arm/mach-at91rm9200/board-ecbat91.c -+ * Copyright (C) 2007 emQbit.com. -+ * -+ * We started from board-dk.c, which is Copyright (C) 2005 SAN People. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/spi/flash.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+ -+#include "generic.h" -+ -+ -+static void __init ecb_at91map_io(void) -+{ -+ /* Initialize processor: 18.432 MHz crystal */ -+ at91rm9200_initialize(18432000, AT91RM9200_PQFP); -+ -+ /* Setup the LEDs */ -+ at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7); -+ -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1. (Rx & Tx only) */ -+ at91_register_uart(AT91RM9200_ID_US0, 1, 0); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); -+} -+ -+static void __init ecb_at91init_irq(void) -+{ -+ at91rm9200_init_interrupts(NULL); -+} -+ -+static struct at91_eth_data __initdata ecb_at91eth_data = { -+ .phy_irq_pin = AT91_PIN_PC4, -+ .is_rmii = 0, -+}; -+ -+static struct at91_usbh_data __initdata ecb_at91usbh_data = { -+ .ports = 1, -+}; -+ -+static struct at91_mmc_data __initdata ecb_at91mmc_data = { -+ .slot_b = 0, -+ .wire4 = 1, -+}; -+ -+ -+#if defined(CONFIG_MTD_DATAFLASH) -+static struct mtd_partition __initdata my_flash0_partitions[] = -+{ -+ { /* 0x8400 */ -+ .name = "Darrell-loader", -+ .offset = 0, -+ .size = 12* 1056, -+ }, -+ { -+ .name = "U-boot", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 110 * 1056, -+ }, -+ { /* 1336 (167 blocks) pages * 1056 bytes = 0x158700 bytes */ -+ .name = "Uoot-env", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 8 * 1056, -+ }, -+ { /* 1336 (167 blocks) pages * 1056 bytes = 0x158700 bytes */ -+ .name = "Kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 1534 * 1056, -+ }, -+ { /* 190200 - jffs2 root filesystem */ -+ .name = "Filesystem", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL, /* 26 sectors */ -+ } -+}; -+ -+static struct flash_platform_data __initdata my_flash0_platform = { -+ .name = "Removable flash card", -+ .parts = my_flash0_partitions, -+ .nr_parts = ARRAY_SIZE(my_flash0_partitions) -+}; -+ -+#endif -+ -+static struct spi_board_info __initdata ecb_at91spi_devices[] = { -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 10 * 1000 * 1000, -+ .bus_num = 0, -+#if defined(CONFIG_MTD_DATAFLASH) -+ .platform_data = &my_flash0_platform, -+#endif -+ }, -+ { /* User accessable spi - cs1 (250KHz) */ -+ .modalias = "spi-cs1", -+ .chip_select = 1, -+ .max_speed_hz = 250 * 1000, -+ }, -+ { /* User accessable spi - cs2 (1MHz) */ -+ .modalias = "spi-cs2", -+ .chip_select = 2, -+ .max_speed_hz = 1 * 1000 * 1000, -+ }, -+ { /* User accessable spi - cs3 (10MHz) */ -+ .modalias = "spi-cs3", -+ .chip_select = 3, -+ .max_speed_hz = 10 * 1000 * 1000, -+ }, -+}; -+ -+static void __init ecb_at91board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ -+ /* Ethernet */ -+ at91_add_device_eth(&ecb_at91eth_data); -+ -+ /* USB Host */ -+ at91_add_device_usbh(&ecb_at91usbh_data); -+ -+ /* I2C */ -+ at91_add_device_i2c(NULL, 0); -+ -+ /* MMC */ -+ at91_add_device_mmc(0, &ecb_at91mmc_data); -+ -+ /* SPI */ -+ at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices)); -+} -+ -+MACHINE_START(ECBAT91, "emQbit's ECB_AT91") -+ /* Maintainer: emQbit.com */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91rm9200_timer, -+ .map_io = ecb_at91map_io, -+ .init_irq = ecb_at91init_irq, -+ .init_machine = ecb_at91board_init, -+MACHINE_END ---- a/arch/arm/mach-at91/board-ek.c -+++ b/arch/arm/mach-at91/board-ek.c -@@ -25,6 +25,7 @@ - #include <linux/init.h> - #include <linux/mm.h> - #include <linux/module.h> -+#include <linux/dma-mapping.h> - #include <linux/platform_device.h> - #include <linux/spi/spi.h> - #include <linux/mtd/physmap.h> -@@ -45,17 +46,6 @@ - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 3 = USART0 .. USART3 -- * 4 = DBGU -- */ --static struct at91_uart_config __initdata ek_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 2, -- .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ --}; -- - static void __init ek_map_io(void) - { - /* Initialize processor: 18.432 MHz crystal */ -@@ -64,8 +54,16 @@ static void __init ek_map_io(void) - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); - -- /* Setup the serial ports and console */ -- at91_init_serial(&ek_uart_config); -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS -+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD -+ | ATMEL_UART_RI); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init ek_init_irq(void) -@@ -73,6 +71,187 @@ static void __init ek_init_irq(void) - at91rm9200_init_interrupts(NULL); - } - -+#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE) -+#include <video/s1d13xxxfb.h> -+#include <asm/arch/ics1523.h> -+ -+/* EPSON S1D13806 FB */ -+#define AT91_FB_REG_BASE 0x40000000L -+#define AT91_FB_REG_SIZE 0x200 -+#define AT91_FB_VMEM_BASE 0x40200000L -+#define AT91_FB_VMEM_SIZE 0x140000L -+ -+static void ek_init_video(void) -+{ -+ /* NWAIT Signal */ -+ at91_set_A_periph(AT91_PIN_PC6, 0); -+ -+ /* Initialization of the Static Memory Controller for Chip Select 3 */ -+ at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_DBW_16 /* 16 bit */ -+ | AT91_SMC_WSEN | AT91_SMC_NWS_(5) /* wait states */ -+ | AT91_SMC_TDF_(1) /* float time */ -+ ); -+ -+ at91_ics1523_init(); -+} -+ -+/* CRT: (active) 640x480 60Hz (PCLK=CLKI=25.175MHz) -+ Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */ -+static const struct s1d13xxxfb_regval ek_s1dfb_initregs[] = { -+ {S1DREG_MISC, 0x00}, /* Enable Memory/Register select bit */ -+ {S1DREG_COM_DISP_MODE, 0x00}, /* disable display output */ -+ {S1DREG_GPIO_CNF0, 0xFF}, // 0x00 -+ {S1DREG_GPIO_CNF1, 0x1F}, // 0x08 -+ {S1DREG_GPIO_CTL0, 0x00}, -+ {S1DREG_GPIO_CTL1, 0x00}, -+ {S1DREG_CLK_CNF, 0x01}, /* no divide, MCLK source is CLKI3 0x02*/ -+ {S1DREG_LCD_CLK_CNF, 0x00}, -+ {S1DREG_CRT_CLK_CNF, 0x00}, -+ {S1DREG_MPLUG_CLK_CNF, 0x00}, -+ {S1DREG_CPU2MEM_WST_SEL, 0x01}, /* 2*period(MCLK) - 4ns > period(BCLK) */ -+ {S1DREG_SDRAM_REF_RATE, 0x03}, /* 32768 <= MCLK <= 50000 (MHz) */ -+ {S1DREG_SDRAM_TC0, 0x00}, /* MCLK source freq (MHz): */ -+ {S1DREG_SDRAM_TC1, 0x01}, /* 42 <= MCLK <= 50 */ -+ {S1DREG_MEM_CNF, 0x80}, /* SDRAM Initialization - needed before mem access */ -+ {S1DREG_PANEL_TYPE, 0x25}, /* std TFT 16bit, 8bit SCP format 2, single passive LCD */ -+ {S1DREG_MOD_RATE, 0x00}, /* toggle every FPFRAME */ -+ {S1DREG_LCD_DISP_HWIDTH, 0x4F}, /* 680 pix */ -+ {S1DREG_LCD_NDISP_HPER, 0x12}, /* 152 pix */ -+ {S1DREG_TFT_FPLINE_START, 0x01}, /* 13 pix */ -+ {S1DREG_TFT_FPLINE_PWIDTH, 0x0B}, /* 96 pix */ -+ {S1DREG_LCD_DISP_VHEIGHT0, 0xDF}, -+ {S1DREG_LCD_DISP_VHEIGHT1, 0x01}, /* 480 lines */ -+ {S1DREG_LCD_NDISP_VPER, 0x2C}, /* 44 lines */ -+ {S1DREG_TFT_FPFRAME_START, 0x0A}, /* 10 lines */ -+ {S1DREG_TFT_FPFRAME_PWIDTH, 0x01}, /* 2 lines */ -+ {S1DREG_LCD_DISP_MODE, 0x05}, /* 16 bpp */ -+ {S1DREG_LCD_MISC, 0x00}, /* dithering enabled, dual panel buffer enabled */ -+ {S1DREG_LCD_DISP_START0, 0x00}, -+ {S1DREG_LCD_DISP_START1, 0xC8}, -+ {S1DREG_LCD_DISP_START2, 0x00}, -+ {S1DREG_LCD_MEM_OFF0, 0x80}, -+ {S1DREG_LCD_MEM_OFF1, 0x02}, -+ {S1DREG_LCD_PIX_PAN, 0x00}, -+ {S1DREG_LCD_DISP_FIFO_HTC, 0x3B}, -+ {S1DREG_LCD_DISP_FIFO_LTC, 0x3C}, -+ {S1DREG_CRT_DISP_HWIDTH, 0x4F}, /* 680 pix */ -+ {S1DREG_CRT_NDISP_HPER, 0x13}, /* 160 pix */ -+ {S1DREG_CRT_HRTC_START, 0x01}, /* 13 pix */ -+ {S1DREG_CRT_HRTC_PWIDTH, 0x0B}, /* 96 pix */ -+ {S1DREG_CRT_DISP_VHEIGHT0, 0xDF}, -+ {S1DREG_CRT_DISP_VHEIGHT1, 0x01}, /* 480 lines */ -+ {S1DREG_CRT_NDISP_VPER, 0x2B}, /* 44 lines */ -+ {S1DREG_CRT_VRTC_START, 0x09}, /* 10 lines */ -+ {S1DREG_CRT_VRTC_PWIDTH, 0x01}, /* 2 lines */ -+ {S1DREG_TV_OUT_CTL, 0x10}, -+ {0x005E, 0x9F}, -+ {0x005F, 0x00}, -+ {S1DREG_CRT_DISP_MODE, 0x05}, /* 16 bpp */ -+ {S1DREG_CRT_DISP_START0, 0x00}, -+ {S1DREG_CRT_DISP_START1, 0x00}, -+ {S1DREG_CRT_DISP_START2, 0x00}, -+ {S1DREG_CRT_MEM_OFF0, 0x80}, -+ {S1DREG_CRT_MEM_OFF1, 0x02}, -+ {S1DREG_CRT_PIX_PAN, 0x00}, -+ {S1DREG_CRT_DISP_FIFO_HTC, 0x3B}, -+ {S1DREG_CRT_DISP_FIFO_LTC, 0x3C}, -+ {S1DREG_LCD_CUR_CTL, 0x00}, /* inactive */ -+ {S1DREG_LCD_CUR_START, 0x01}, -+ {S1DREG_LCD_CUR_XPOS0, 0x00}, -+ {S1DREG_LCD_CUR_XPOS1, 0x00}, -+ {S1DREG_LCD_CUR_YPOS0, 0x00}, -+ {S1DREG_LCD_CUR_YPOS1, 0x00}, -+ {S1DREG_LCD_CUR_BCTL0, 0x00}, -+ {S1DREG_LCD_CUR_GCTL0, 0x00}, -+ {S1DREG_LCD_CUR_RCTL0, 0x00}, -+ {S1DREG_LCD_CUR_BCTL1, 0x1F}, -+ {S1DREG_LCD_CUR_GCTL1, 0x3F}, -+ {S1DREG_LCD_CUR_RCTL1, 0x1F}, -+ {S1DREG_LCD_CUR_FIFO_HTC, 0x00}, -+ {S1DREG_CRT_CUR_CTL, 0x00}, /* inactive */ -+ {S1DREG_CRT_CUR_START, 0x01}, -+ {S1DREG_CRT_CUR_XPOS0, 0x00}, -+ {S1DREG_CRT_CUR_XPOS1, 0x00}, -+ {S1DREG_CRT_CUR_YPOS0, 0x00}, -+ {S1DREG_CRT_CUR_YPOS1, 0x00}, -+ {S1DREG_CRT_CUR_BCTL0, 0x00}, -+ {S1DREG_CRT_CUR_GCTL0, 0x00}, -+ {S1DREG_CRT_CUR_RCTL0, 0x00}, -+ {S1DREG_CRT_CUR_BCTL1, 0x1F}, -+ {S1DREG_CRT_CUR_GCTL1, 0x3F}, -+ {S1DREG_CRT_CUR_RCTL1, 0x1F}, -+ {S1DREG_CRT_CUR_FIFO_HTC, 0x00}, -+ {S1DREG_BBLT_CTL0, 0x00}, -+ {S1DREG_BBLT_CTL0, 0x00}, -+ {S1DREG_BBLT_CC_EXP, 0x00}, -+ {S1DREG_BBLT_OP, 0x00}, -+ {S1DREG_BBLT_SRC_START0, 0x00}, -+ {S1DREG_BBLT_SRC_START1, 0x00}, -+ {S1DREG_BBLT_SRC_START2, 0x00}, -+ {S1DREG_BBLT_DST_START0, 0x00}, -+ {S1DREG_BBLT_DST_START1, 0x00}, -+ {S1DREG_BBLT_DST_START2, 0x00}, -+ {S1DREG_BBLT_MEM_OFF0, 0x00}, -+ {S1DREG_BBLT_MEM_OFF1, 0x00}, -+ {S1DREG_BBLT_WIDTH0, 0x00}, -+ {S1DREG_BBLT_WIDTH1, 0x00}, -+ {S1DREG_BBLT_HEIGHT0, 0x00}, -+ {S1DREG_BBLT_HEIGHT1, 0x00}, -+ {S1DREG_BBLT_BGC0, 0x00}, -+ {S1DREG_BBLT_BGC1, 0x00}, -+ {S1DREG_BBLT_FGC0, 0x00}, -+ {S1DREG_BBLT_FGC1, 0x00}, -+ {S1DREG_LKUP_MODE, 0x00}, /* LCD LUT r | LCD and CRT/TV LUT w */ -+ {S1DREG_LKUP_ADDR, 0x00}, -+ {S1DREG_PS_CNF, 0x10}, /* Power Save disable */ -+ {S1DREG_PS_STATUS, 0x02}, /* LCD Panel down, mem up */ -+ {S1DREG_CPU2MEM_WDOGT, 0x00}, -+ {S1DREG_COM_DISP_MODE, 0x02}, /* enable CRT display output */ -+}; -+ -+static struct s1d13xxxfb_pdata ek_s1dfb_pdata = { -+ .initregs = ek_s1dfb_initregs, -+ .initregssize = ARRAY_SIZE(ek_s1dfb_initregs), -+ .platform_init_video = ek_init_video, -+}; -+ -+static u64 s1dfb_dmamask = DMA_BIT_MASK(32); -+ -+static struct resource ek_s1dfb_resource[] = { -+ [0] = { /* video mem */ -+ .name = "s1d13806 memory", -+ .start = AT91_FB_VMEM_BASE, -+ .end = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1, -+ .flags = IORESOURCE_MEM, -+ }, -+ [1] = { /* video registers */ -+ .name = "s1d13806 registers", -+ .start = AT91_FB_REG_BASE, -+ .end = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1, -+ .flags = IORESOURCE_MEM, -+ }, -+}; -+ -+static struct platform_device ek_s1dfb_device = { -+ .name = "s1d13806fb", -+ .id = -1, -+ .dev = { -+ .dma_mask = &s1dfb_dmamask, -+ .coherent_dma_mask = DMA_BIT_MASK(32), -+ .platform_data = &ek_s1dfb_pdata, -+ }, -+ .resource = ek_s1dfb_resource, -+ .num_resources = ARRAY_SIZE(ek_s1dfb_resource), -+}; -+ -+static void __init ek_add_device_video(void) -+{ -+ platform_device_register(&ek_s1dfb_device); -+} -+#else -+static void __init ek_add_device_video(void) {} -+#endif -+ - static struct at91_eth_data __initdata ek_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -@@ -122,7 +301,7 @@ static struct i2c_board_info __initdata - #define EK_FLASH_SIZE 0x200000 - - static struct physmap_flash_data ek_flash_data = { -- .width = 2, -+ .width = 2, - }; - - static struct resource ek_flash_resource = { -@@ -189,7 +368,7 @@ static void __init ek_board_init(void) - /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); - /* VGA */ --// ek_add_device_video(); -+ ek_add_device_video(); - } - - MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK") ---- /dev/null -+++ b/arch/arm/mach-at91/board-homematic.c -@@ -0,0 +1,163 @@ -+/* -+ * linux/arch/arm/mach-at91/board-homematic.c -+ * -+ * Copyright (C) 2007 eQ-3 Entwicklung GmbH -+ * -+ * based on work -+ * Copyright (C) 2005 SAN People -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/mtd/physmap.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/at91rm9200_mc.h> -+ -+#include "generic.h" -+ -+ -+/* -+ * Serial port configuration. -+ * 0 .. 3 = USART0 .. USART3 -+ * 4 = DBGU -+ */ -+static struct at91_uart_config __initdata homematic_uart_config = { -+ .console_tty = 0, /* ttyS0 */ -+ .nr_tty = 2, -+ .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ -+}; -+ -+static void __init homematic_map_io(void) -+{ -+ /* Initialize processor: 18.432 MHz crystal */ -+ at91rm9200_initialize(18432000, AT91RM9200_BGA); -+ -+ /* Setup the serial ports and console */ -+ at91_init_serial(&homematic_uart_config); -+} -+ -+static void __init homematic_init_irq(void) -+{ -+ at91rm9200_init_interrupts(NULL); -+} -+ -+static struct at91_eth_data __initdata homematic_eth_data = { -+ .phy_irq_pin = AT91_PIN_PC4, -+ .is_rmii = 0, -+}; -+ -+static struct at91_usbh_data __initdata homematic_usbh_data = { -+ .ports = 2, -+}; -+ -+static struct at91_udc_data __initdata homematic_udc_data = { -+ .vbus_pin = AT91_PIN_PD4, -+ .pullup_pin = AT91_PIN_PD5, -+}; -+ -+static struct at91_mmc_data __initdata homematic_mmc_data = { -+ .slot_b = 0, -+ .wire4 = 1, -+}; -+ -+static struct spi_board_info homematic_spi_devices[] = { -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 15 * 1000 * 1000, -+ }, -+}; -+ -+static struct mtd_partition __initdata homematic_nand_partition[] = { -+ { -+ .name = "root", -+ .offset = 0, -+ .size = 0x02000000, -+ }, { -+ .name = "storage", -+ .offset = 0x02000000, -+ .size = MTDPART_SIZ_FULL, -+ }, -+}; -+ -+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -+{ -+ *num_partitions = ARRAY_SIZE(homematic_nand_partition); -+ return homematic_nand_partition; -+} -+ -+static struct at91_nand_data __initdata homematic_nand_data = { -+ .ale = 22, -+ .cle = 21, -+// .det_pin = AT91_PIN_PB1, -+ .rdy_pin = AT91_PIN_PC2, -+ .enable_pin = AT91_PIN_PC0, -+ .partition_info = nand_partitions, -+}; -+ -+static void __init homematic_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* Ethernet */ -+ at91_add_device_eth(&homematic_eth_data); -+ /* USB Host */ -+ at91_add_device_usbh(&homematic_usbh_data); -+ /* USB Device */ -+ at91_add_device_udc(&homematic_udc_data); -+ at91_set_multi_drive(homematic_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ -+ /* I2C */ -+ at91_add_device_i2c(NULL, 0); -+ /* SPI */ -+ at91_add_device_spi(homematic_spi_devices, ARRAY_SIZE(homematic_spi_devices)); -+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD -+ /* DataFlash card */ -+ at91_set_gpio_output(AT91_PIN_PB7, 0); -+#else -+ /* MMC */ -+ at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ -+ at91_add_device_mmc(0, &homematic_mmc_data); -+#endif -+ /* NAND */ -+ at91_add_device_nand(&homematic_nand_data); -+} -+ -+MACHINE_START(HOMEMATIC, "HomeMatic") -+ /* Maintainer: eQ-3 */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91rm9200_timer, -+ .map_io = homematic_map_io, -+ .init_irq = homematic_init_irq, -+ .init_machine = homematic_board_init, -+MACHINE_END ---- a/arch/arm/mach-at91/board-kb9202.c -+++ b/arch/arm/mach-at91/board-kb9202.c -@@ -37,19 +37,10 @@ - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> - --#include "generic.h" -+#include <asm/arch/at91rm9200_mc.h> - -+#include "generic.h" - --/* -- * Serial port configuration. -- * 0 .. 3 = USART0 .. USART3 -- * 4 = DBGU -- */ --static struct at91_uart_config __initdata kb9202_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 3, -- .tty_map = { 4, 0, 1, -1, -1 } /* ttyS0, ..., ttyS4 */ --}; - - static void __init kb9202_map_io(void) - { -@@ -59,8 +50,20 @@ static void __init kb9202_map_io(void) - /* Set up the LEDs */ - at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); - -- /* Setup the serial ports and console */ -- at91_init_serial(&kb9202_uart_config); -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1 (Rx & Tx only) */ -+ at91_register_uart(AT91RM9200_ID_US0, 1, 0); -+ -+ /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */ -+ at91_register_uart(AT91RM9200_ID_US1, 2, 0); -+ -+ /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */ -+ at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init kb9202_init_irq(void) -@@ -111,6 +114,48 @@ static struct at91_nand_data __initdata - .partition_info = nand_partitions, - }; - -+ -+#if defined(CONFIG_FB_S1D15605) -+#warning "The Reset pin must be passed via platform_data, not this way" -+static struct resource kb9202_lcd_resources[] = { -+ [0] = { -+ .start = AT91_CHIPSELECT_2, -+ .end = AT91_CHIPSELECT_2 + 0x200FF, -+ .flags = IORESOURCE_MEM -+ }, -+ [1] = { /* reset pin */ -+ .start = AT91_PIN_PC22, -+ .end = AT91_PIN_PC22, -+ .flags = IORESOURCE_MEM -+ }, -+}; -+ -+static struct platform_device kb9202_lcd_device = { -+ .name = "s1d15605fb", -+ .id = 0, -+ .num_resources = ARRAY_SIZE(kb9202_lcd_resources), -+ .resource = kb9202_lcd_resources, -+}; -+ -+static void __init kb9202_add_device_lcd(void) -+{ -+ /* In case the boot loader did not set the chip select mode and timing */ -+ at91_sys_write(AT91_SMC_CSR(2), -+ AT91_SMC_WSEN | AT91_SMC_NWS_(18) | AT91_SMC_TDF_(1) | AT91_SMC_DBW_8 | -+ AT91_SMC_RWSETUP_(1) | AT91_SMC_RWHOLD_(1)); -+ -+ /* Backlight pin = output, off */ -+ at91_set_gpio_output(AT91_PIN_PC23, 0); -+ -+ /* Reset pin = output, in reset */ -+ at91_set_gpio_output(AT91_PIN_PC22, 0); -+ -+ platform_device_register(&kb9202_lcd_device); -+} -+#else -+static void __init kb9202_add_device_lcd(void) {} -+#endif -+ - static void __init kb9202_board_init(void) - { - /* Serial */ -@@ -129,6 +174,8 @@ static void __init kb9202_board_init(voi - at91_add_device_spi(NULL, 0); - /* NAND */ - at91_add_device_nand(&kb9202_nand_data); -+ /* LCD */ -+ kb9202_add_device_lcd(); - } - - MACHINE_START(KB9200, "KB920x") ---- /dev/null -+++ b/arch/arm/mach-at91/board-qil-a9260.c -@@ -0,0 +1,255 @@ -+/* -+ * linux/arch/arm/mach-at91/board-qil-a9260.c -+ * -+ * Copyright (C) 2005 SAN People -+ * Copyright (C) 2006 Atmel -+ * Copyright (C) 2007 Calao-systems -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/clk.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/at91_shdwc.h> -+ -+#include "generic.h" -+ -+ -+static void __init ek_map_io(void) -+{ -+ /* Initialize processor: 12.000 MHz crystal */ -+ at91sam9260_initialize(12000000); -+ -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS -+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD -+ | ATMEL_UART_RI); -+ -+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ -+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ -+ at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* set serial console to ttyS1 (ie, USART0) */ -+ at91_set_serial_console(1); -+ -+} -+ -+static void __init ek_init_irq(void) -+{ -+ at91sam9260_init_interrupts(NULL); -+} -+ -+ -+/* -+ * USB Host port -+ */ -+static struct at91_usbh_data __initdata ek_usbh_data = { -+ .ports = 2, -+}; -+ -+/* -+ * USB Device port -+ */ -+static struct at91_udc_data __initdata ek_udc_data = { -+ .vbus_pin = AT91_PIN_PC5, -+ .pullup_pin = 0, /* pull-up driven by UDC */ -+}; -+ -+/* -+ * SPI devices. -+ */ -+static struct spi_board_info ek_spi_devices[] = { -+#if defined(CONFIG_RTC_DRV_M41T94) -+ { /* M41T94 RTC */ -+ .modalias = "m41t94", -+ .chip_select = 0, -+ .max_speed_hz = 1 * 1000 * 1000, -+ .bus_num = 0, -+ } -+#endif -+}; -+ -+/* -+ * MACB Ethernet device -+ */ -+static struct at91_eth_data __initdata ek_macb_data = { -+ .phy_irq_pin = AT91_PIN_PA31, -+ .is_rmii = 1, -+}; -+ -+/* -+ * NAND flash -+ */ -+static struct mtd_partition __initdata ek_nand_partition[] = { -+ { -+ .name = "Uboot & Kernel", -+ .offset = 0x00000000, -+ .size = 16 * 1024 * 1024, -+ }, -+ { -+ .name = "Root FS", -+ .offset = 0x01000000, -+ .size = 120 * 1024 * 1024, -+ }, -+ { -+ .name = "FS", -+ .offset = 0x08800000, -+ .size = 120 * 1024 * 1024, -+ }, -+}; -+ -+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -+{ -+ *num_partitions = ARRAY_SIZE(ek_nand_partition); -+ return ek_nand_partition; -+} -+ -+static struct at91_nand_data __initdata ek_nand_data = { -+ .ale = 21, -+ .cle = 22, -+// .det_pin = ... not connected -+ .rdy_pin = AT91_PIN_PC13, -+ .enable_pin = AT91_PIN_PC14, -+ .partition_info = nand_partitions, -+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) -+ .bus_width_16 = 1, -+#else -+ .bus_width_16 = 0, -+#endif -+}; -+ -+/* -+ * MCI (SD/MMC) -+ */ -+static struct at91_mmc_data __initdata ek_mmc_data = { -+ .slot_b = 0, -+ .wire4 = 1, -+// .det_pin = ... not connected -+// .wp_pin = ... not connected -+// .vcc_pin = ... not connected -+}; -+ -+/* -+ * GPIO Buttons -+ */ -+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -+static struct gpio_keys_button ek_buttons[] = { -+ { /* USER PUSH BUTTON */ -+ .code = KEY_ENTER, -+ .gpio = AT91_PIN_PB10, -+ .active_low = 1, -+ .desc = "user_pb", -+ .wakeup = 1, -+ } -+}; -+ -+static struct gpio_keys_platform_data ek_button_data = { -+ .buttons = ek_buttons, -+ .nbuttons = ARRAY_SIZE(ek_buttons), -+}; -+ -+static struct platform_device ek_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &ek_button_data, -+ } -+}; -+ -+static void __init ek_add_device_buttons(void) -+{ -+ at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ -+ at91_set_deglitch(AT91_PIN_PB10, 1); -+ -+ platform_device_register(&ek_button_device); -+} -+#else -+static void __init ek_add_device_buttons(void) {} -+#endif -+ -+/* -+ * LEDs -+ */ -+static struct gpio_led ek_leds[] = { -+ { /* user_led (green) */ -+ .name = "user_led", -+ .gpio = AT91_PIN_PB21, -+ .active_low = 0, -+ .default_trigger = "heartbeat", -+ } -+}; -+ -+static void __init ek_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* USB Host */ -+ at91_add_device_usbh(&ek_usbh_data); -+ /* USB Device */ -+ at91_add_device_udc(&ek_udc_data); -+ /* SPI */ -+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); -+ /* NAND */ -+ at91_add_device_nand(&ek_nand_data); -+ /* I2C */ -+ at91_add_device_i2c(NULL, 0); -+ /* Ethernet */ -+ at91_add_device_eth(&ek_macb_data); -+ /* MMC */ -+ at91_add_device_mmc(0, &ek_mmc_data); -+ /* Push Buttons */ -+ ek_add_device_buttons(); -+ /* LEDs */ -+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); -+ /* shutdown controller, wakeup button (5 msec low) */ -+ at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW -+ | AT91_SHDW_RTTWKEN); -+} -+ -+MACHINE_START(QIL_A9260, "CALAO QIL_A9260") -+ /* Maintainer: calao-systems */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91sam926x_timer, -+ .map_io = ek_map_io, -+ .init_irq = ek_init_irq, -+ .init_machine = ek_board_init, -+MACHINE_END ---- /dev/null -+++ b/arch/arm/mach-at91/board-sam9-l9260.c -@@ -0,0 +1,199 @@ -+/* -+ * linux/arch/arm/mach-at91/board-sam9-l9260.c -+ * -+ * Copyright (C) 2005 SAN People -+ * Copyright (C) 2006 Atmel -+ * Copyright (C) 2007 Olimex Ltd -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+ -+#include "generic.h" -+ -+ -+static void __init ek_map_io(void) -+{ -+ /* Initialize processor: 18.432 MHz crystal */ -+ at91sam9260_initialize(18432000); -+ -+ /* Setup the LEDs */ -+ at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6); -+ -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS -+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD -+ | ATMEL_UART_RI); -+ -+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ -+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); -+} -+ -+static void __init ek_init_irq(void) -+{ -+ at91sam9260_init_interrupts(NULL); -+} -+ -+ -+/* -+ * USB Host port -+ */ -+static struct at91_usbh_data __initdata ek_usbh_data = { -+ .ports = 2, -+}; -+ -+/* -+ * USB Device port -+ */ -+static struct at91_udc_data __initdata ek_udc_data = { -+ .vbus_pin = AT91_PIN_PC5, -+ .pullup_pin = 0, /* pull-up driven by UDC */ -+}; -+ -+ -+/* -+ * SPI devices. -+ */ -+static struct spi_board_info ek_spi_devices[] = { -+#if !defined(CONFIG_MMC_AT91) -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 1, -+ .max_speed_hz = 15 * 1000 * 1000, -+ .bus_num = 0, -+ }, -+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) -+ { /* DataFlash card */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 15 * 1000 * 1000, -+ .bus_num = 0, -+ }, -+#endif -+#endif -+}; -+ -+ -+/* -+ * MACB Ethernet device -+ */ -+static struct at91_eth_data __initdata ek_macb_data = { -+ .phy_irq_pin = AT91_PIN_PA7, -+ .is_rmii = 0, -+}; -+ -+ -+/* -+ * NAND flash -+ */ -+static struct mtd_partition __initdata ek_nand_partition[] = { -+ { -+ .name = "Bootloader Area", -+ .offset = 0, -+ .size = 10 * 1024 * 1024, -+ }, -+ { -+ .name = "User Area", -+ .offset = 10 * 1024 * 1024, -+ .size = MTDPART_SIZ_FULL, -+ }, -+}; -+ -+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -+{ -+ *num_partitions = ARRAY_SIZE(ek_nand_partition); -+ return ek_nand_partition; -+} -+ -+static struct at91_nand_data __initdata ek_nand_data = { -+ .ale = 21, -+ .cle = 22, -+// .det_pin = ... not connected -+ .rdy_pin = AT91_PIN_PC13, -+ .enable_pin = AT91_PIN_PC14, -+ .partition_info = nand_partitions, -+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) -+ .bus_width_16 = 1, -+#else -+ .bus_width_16 = 0, -+#endif -+}; -+ -+ -+/* -+ * MCI (SD/MMC) -+ */ -+static struct at91_mmc_data __initdata ek_mmc_data = { -+ .slot_b = 1, -+ .wire4 = 1, -+ .det_pin = AT91_PIN_PC8, -+ .wp_pin = AT91_PIN_PC4, -+// .vcc_pin = ... not connected -+}; -+ -+static void __init ek_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* USB Host */ -+ at91_add_device_usbh(&ek_usbh_data); -+ /* USB Device */ -+ at91_add_device_udc(&ek_udc_data); -+ /* SPI */ -+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); -+ /* NAND */ -+ at91_add_device_nand(&ek_nand_data); -+ /* Ethernet */ -+ at91_add_device_eth(&ek_macb_data); -+ /* MMC */ -+ at91_add_device_mmc(0, &ek_mmc_data); -+ /* I2C */ -+ at91_add_device_i2c(NULL, 0); -+} -+ -+MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260") -+ /* Maintainer: Olimex */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91sam926x_timer, -+ .map_io = ek_map_io, -+ .init_irq = ek_init_irq, -+ .init_machine = ek_board_init, -+MACHINE_END ---- a/arch/arm/mach-at91/board-sam9260ek.c -+++ b/arch/arm/mach-at91/board-sam9260ek.c -@@ -25,6 +25,10 @@ - #include <linux/module.h> - #include <linux/platform_device.h> - #include <linux/spi/spi.h> -+#include <linux/spi/at73c213.h> -+#include <linux/clk.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> - - #include <asm/hardware.h> - #include <asm/setup.h> -@@ -37,29 +41,29 @@ - - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> --#include <asm/arch/at91sam926x_mc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 5 = USART0 .. USART5 -- * 6 = DBGU -- */ --static struct at91_uart_config __initdata ek_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 3, -- .tty_map = { 6, 0, 1, -1, -1, -1, -1 } /* ttyS0, ..., ttyS6 */ --}; -- - static void __init ek_map_io(void) - { - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - -- /* Setup the serial ports and console */ -- at91_init_serial(&ek_uart_config); -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ -+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS -+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD -+ | ATMEL_UART_RI); -+ -+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ -+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init ek_init_irq(void) -@@ -85,6 +89,35 @@ static struct at91_udc_data __initdata e - - - /* -+ * Audio -+ */ -+static struct at73c213_board_info at73c213_data = { -+ .ssc_id = 0, -+ .shortname = "AT91SAM9260-EK external DAC", -+}; -+ -+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE) -+static void __init at73c213_set_clk(struct at73c213_board_info *info) -+{ -+ struct clk *pck0; -+ struct clk *plla; -+ -+ pck0 = clk_get(NULL, "pck0"); -+ plla = clk_get(NULL, "plla"); -+ -+ /* AT73C213 MCK Clock */ -+ at91_set_B_periph(AT91_PIN_PC1, 0); /* PCK0 */ -+ -+ clk_set_parent(pck0, plla); -+ clk_put(plla); -+ -+ info->dac_clk = pck0; -+} -+#else -+static void __init at73c213_set_clk(struct at73c213_board_info *info) {} -+#endif -+ -+/* - * SPI devices. - */ - static struct spi_board_info ek_spi_devices[] = { -@@ -110,6 +143,8 @@ static struct spi_board_info ek_spi_devi - .chip_select = 0, - .max_speed_hz = 10 * 1000 * 1000, - .bus_num = 1, -+ .mode = SPI_MODE_1, -+ .platform_data = &at73c213_data, - }, - #endif - }; -@@ -172,6 +207,74 @@ static struct at91_mmc_data __initdata e - // .vcc_pin = ... not connected - }; - -+ -+/* -+ * LEDs -+ */ -+static struct gpio_led ek_leds[] = { -+ { /* "bottom" led, green, userled1 to be defined */ -+ .name = "ds5", -+ .gpio = AT91_PIN_PA6, -+ .active_low = 1, -+ .default_trigger = "none", -+ }, -+ { /* "power" led, yellow */ -+ .name = "ds1", -+ .gpio = AT91_PIN_PA9, -+ .default_trigger = "heartbeat", -+ } -+}; -+ -+ -+/* -+ * GPIO Buttons -+ */ -+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -+static struct gpio_keys_button ek_buttons[] = { -+ { -+ .gpio = AT91_PIN_PA30, -+ .code = BTN_3, -+ .desc = "Button 3", -+ .active_low = 1, -+ .wakeup = 1, -+ }, -+ { -+ .gpio = AT91_PIN_PA31, -+ .code = BTN_4, -+ .desc = "Button 4", -+ .active_low = 1, -+ .wakeup = 1, -+ } -+}; -+ -+static struct gpio_keys_platform_data ek_button_data = { -+ .buttons = ek_buttons, -+ .nbuttons = ARRAY_SIZE(ek_buttons), -+}; -+ -+static struct platform_device ek_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &ek_button_data, -+ } -+}; -+ -+static void __init ek_add_device_buttons(void) -+{ -+ at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */ -+ at91_set_deglitch(AT91_PIN_PA30, 1); -+ at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */ -+ at91_set_deglitch(AT91_PIN_PA31, 1); -+ -+ platform_device_register(&ek_button_device); -+} -+#else -+static void __init ek_add_device_buttons(void) {} -+#endif -+ -+ - static void __init ek_board_init(void) - { - /* Serial */ -@@ -190,6 +293,16 @@ static void __init ek_board_init(void) - at91_add_device_mmc(0, &ek_mmc_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); -+ /* SSC (to AT73C213) */ -+ at73c213_set_clk(&at73c213_data); -+ at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); -+ /* LEDs */ -+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); -+ /* Push Buttons */ -+ ek_add_device_buttons(); -+ /* shutdown controller, wakeup button (5 msec low) */ -+ at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW -+ | AT91_SHDW_RTTWKEN); - } - - MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK") ---- a/arch/arm/mach-at91/board-sam9261ek.c -+++ b/arch/arm/mach-at91/board-sam9261ek.c -@@ -26,6 +26,8 @@ - #include <linux/platform_device.h> - #include <linux/spi/spi.h> - #include <linux/spi/ads7846.h> -+#include <linux/spi/at73c213.h> -+#include <linux/clk.h> - #include <linux/dm9000.h> - #include <linux/fb.h> - #include <linux/gpio_keys.h> -@@ -44,22 +46,12 @@ - - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> --#include <asm/arch/at91sam926x_mc.h> -+#include <asm/arch/at91sam9_smc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 2 = USART0 .. USART2 -- * 3 = DBGU -- */ --static struct at91_uart_config __initdata ek_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 1, -- .tty_map = { 3, -1, -1, -1 } /* ttyS0, ..., ttyS3 */ --}; -- - static void __init ek_map_io(void) - { - /* Initialize processor: 18.432 MHz crystal */ -@@ -68,8 +60,11 @@ static void __init ek_map_io(void) - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14); - -- /* Setup the serial ports and console */ -- at91_init_serial(&ek_uart_config); -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init ek_init_irq(void) -@@ -239,6 +234,35 @@ static void __init ek_add_device_ts(void - #endif - - /* -+ * Audio -+ */ -+static struct at73c213_board_info at73c213_data = { -+ .ssc_id = 1, -+ .shortname = "AT91SAM9261-EK external DAC", -+}; -+ -+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE) -+static void __init at73c213_set_clk(struct at73c213_board_info *info) -+{ -+ struct clk *pck2; -+ struct clk *plla; -+ -+ pck2 = clk_get(NULL, "pck2"); -+ plla = clk_get(NULL, "plla"); -+ -+ /* AT73C213 MCK Clock */ -+ at91_set_B_periph(AT91_PIN_PB31, 0); /* PCK2 */ -+ -+ clk_set_parent(pck2, plla); -+ clk_put(plla); -+ -+ info->dac_clk = pck2; -+} -+#else -+static void __init at73c213_set_clk(struct at73c213_board_info *info) {} -+#endif -+ -+/* - * SPI devices - */ - static struct spi_board_info ek_spi_devices[] = { -@@ -252,10 +276,11 @@ static struct spi_board_info ek_spi_devi - { - .modalias = "ads7846", - .chip_select = 2, -- .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */ -+ .max_speed_hz = 125000 * 16, /* max sample rate * clocks per sample */ - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91SAM9261_ID_IRQ0, -+ .controller_data = (void *) AT91_PIN_PA28, /* CS pin */ - }, - #endif - #if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) -@@ -271,6 +296,9 @@ static struct spi_board_info ek_spi_devi - .chip_select = 3, - .max_speed_hz = 10 * 1000 * 1000, - .bus_num = 0, -+ .mode = SPI_MODE_1, -+ .platform_data = &at73c213_data, -+ .controller_data = (void*) AT91_PIN_PA29, /* default for CS3 is PA6, but it must be PA29 */ - }, - #endif - }; -@@ -408,24 +436,28 @@ static struct gpio_keys_button ek_button - .code = BTN_0, - .desc = "Button 0", - .active_low = 1, -+ .wakeup = 1, - }, - { - .gpio = AT91_PIN_PA26, - .code = BTN_1, - .desc = "Button 1", - .active_low = 1, -+ .wakeup = 1, - }, - { - .gpio = AT91_PIN_PA25, - .code = BTN_2, - .desc = "Button 2", - .active_low = 1, -+ .wakeup = 1, - }, - { - .gpio = AT91_PIN_PA24, - .code = BTN_3, - .desc = "Button 3", - .active_low = 1, -+ .wakeup = 1, - } - }; - -@@ -445,13 +477,13 @@ static struct platform_device ek_button_ - - static void __init ek_add_device_buttons(void) - { -- at91_set_gpio_input(AT91_PIN_PA27, 0); /* btn0 */ -+ at91_set_gpio_input(AT91_PIN_PA27, 1); /* btn0 */ - at91_set_deglitch(AT91_PIN_PA27, 1); -- at91_set_gpio_input(AT91_PIN_PA26, 0); /* btn1 */ -+ at91_set_gpio_input(AT91_PIN_PA26, 1); /* btn1 */ - at91_set_deglitch(AT91_PIN_PA26, 1); -- at91_set_gpio_input(AT91_PIN_PA25, 0); /* btn2 */ -+ at91_set_gpio_input(AT91_PIN_PA25, 1); /* btn2 */ - at91_set_deglitch(AT91_PIN_PA25, 1); -- at91_set_gpio_input(AT91_PIN_PA24, 0); /* btn3 */ -+ at91_set_gpio_input(AT91_PIN_PA24, 1); /* btn3 */ - at91_set_deglitch(AT91_PIN_PA24, 1); - - platform_device_register(&ek_button_device); -@@ -460,6 +492,29 @@ static void __init ek_add_device_buttons - static void __init ek_add_device_buttons(void) {} - #endif - -+/* -+ * LEDs -+ */ -+static struct gpio_led ek_leds[] = { -+ { /* "bottom" led, green, userled1 to be defined */ -+ .name = "ds7", -+ .gpio = AT91_PIN_PA14, -+ .active_low = 1, -+ .default_trigger = "none", -+ }, -+ { /* "top" led, green, userled2 to be defined */ -+ .name = "ds8", -+ .gpio = AT91_PIN_PA13, -+ .active_low = 1, -+ .default_trigger = "none", -+ }, -+ { /* "power" led, yellow */ -+ .name = "ds1", -+ .gpio = AT91_PIN_PA23, -+ .default_trigger = "heartbeat", -+ } -+}; -+ - static void __init ek_board_init(void) - { - /* Serial */ -@@ -481,6 +536,9 @@ static void __init ek_board_init(void) - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); - /* Touchscreen */ - ek_add_device_ts(); -+ /* SSC (to AT73C213) */ -+ at73c213_set_clk(&at73c213_data); -+ at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX); - #else - /* MMC */ - at91_add_device_mmc(0, &ek_mmc_data); -@@ -489,6 +547,11 @@ static void __init ek_board_init(void) - at91_add_device_lcdc(&ek_lcdc_data); - /* Push Buttons */ - ek_add_device_buttons(); -+ /* LEDs */ -+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); -+ /* shutdown controller, wakeup button (5 msec low) */ -+ at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW -+ | AT91_SHDW_RTTWKEN); - } - - MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK") ---- a/arch/arm/mach-at91/board-sam9263ek.c -+++ b/arch/arm/mach-at91/board-sam9263ek.c -@@ -43,29 +43,24 @@ - - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> --#include <asm/arch/at91sam926x_mc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 2 = USART0 .. USART2 -- * 3 = DBGU -- */ --static struct at91_uart_config __initdata ek_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 2, -- .tty_map = { 3, 0, -1, -1, } /* ttyS0, ..., ttyS3 */ --}; -- - static void __init ek_map_io(void) - { - /* Initialize processor: 16.367 MHz crystal */ - at91sam9263_initialize(16367660); - -- /* Setup the serial ports and console */ -- at91_init_serial(&ek_uart_config); -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ -+ at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init ek_init_irq(void) -@@ -141,7 +136,7 @@ static struct spi_board_info ek_spi_devi - { - .modalias = "ads7846", - .chip_select = 3, -- .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */ -+ .max_speed_hz = 125000 * 16, /* max sample rate * clocks per sample */ - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91SAM9263_ID_IRQ1, -@@ -301,9 +296,9 @@ static struct platform_device ek_button_ - - static void __init ek_add_device_buttons(void) - { -- at91_set_GPIO_periph(AT91_PIN_PC5, 0); /* left button */ -+ at91_set_GPIO_periph(AT91_PIN_PC5, 1); /* left button */ - at91_set_deglitch(AT91_PIN_PC5, 1); -- at91_set_GPIO_periph(AT91_PIN_PC4, 0); /* right button */ -+ at91_set_GPIO_periph(AT91_PIN_PC4, 1); /* right button */ - at91_set_deglitch(AT91_PIN_PC4, 1); - - platform_device_register(&ek_button_device); -@@ -341,7 +336,7 @@ static struct gpio_led ek_leds[] = { - .name = "ds3", - .gpio = AT91_PIN_PB7, - .default_trigger = "heartbeat", -- }, -+ } - }; - - -@@ -374,6 +369,9 @@ static void __init ek_board_init(void) - at91_add_device_ac97(&ek_ac97_data); - /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); -+ /* shutdown controller, wakeup button (5 msec low) */ -+ at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW -+ | AT91_SHDW_RTTWKEN); - } - - MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK") ---- a/arch/arm/mach-at91/board-sam9rlek.c -+++ b/arch/arm/mach-at91/board-sam9rlek.c -@@ -29,29 +29,24 @@ - - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> --#include <asm/arch/at91sam926x_mc.h> -+#include <asm/arch/at91_shdwc.h> - - #include "generic.h" - - --/* -- * Serial port configuration. -- * 0 .. 3 = USART0 .. USART3 -- * 4 = DBGU -- */ --static struct at91_uart_config __initdata ek_uart_config = { -- .console_tty = 0, /* ttyS0 */ -- .nr_tty = 2, -- .tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ --}; -- - static void __init ek_map_io(void) - { - /* Initialize processor: 12.000 MHz crystal */ - at91sam9rl_initialize(12000000); - -- /* Setup the serial ports and console */ -- at91_init_serial(&ek_uart_config); -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ -+ at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); - } - - static void __init ek_init_irq(void) -@@ -61,6 +56,14 @@ static void __init ek_init_irq(void) - - - /* -+ * USB HS Device port -+ */ -+static struct usba_platform_data __initdata ek_usba_udc_data = { -+ .vbus_pin = AT91_PIN_PA8, -+}; -+ -+ -+/* - * MCI (SD/MMC) - */ - static struct at91_mmc_data __initdata ek_mmc_data = { -@@ -180,6 +183,8 @@ static void __init ek_board_init(void) - { - /* Serial */ - at91_add_device_serial(); -+ /* USB HS */ -+ at91_add_device_usba(&ek_usba_udc_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* NAND */ -@@ -190,6 +195,9 @@ static void __init ek_board_init(void) - at91_add_device_mmc(0, &ek_mmc_data); - /* LCD Controller */ - at91_add_device_lcdc(&ek_lcdc_data); -+ /* shutdown controller, wakeup button (5 msec low) */ -+ at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW -+ | AT91_SHDW_RTTWKEN); - } - - MACHINE_START(AT91SAM9RLEK, "Atmel AT91SAM9RL-EK") ---- /dev/null -+++ b/arch/arm/mach-at91/board-tms.c -@@ -0,0 +1,198 @@ -+/* -+* linux/arch/arm/mach-at91/board-tms.c -+* -+* Copyright (C) 2005 SAN People -+* -+* Adapted from board-dk to sweda TMS-100 by Luiz de Barros <lboneto@gmail.com> -+* -+* This program is free software; you can redistribute it and/or modify -+* it under the terms of the GNU General Public License as published by -+* the Free Software Foundation; either version 2 of the License, or -+* (at your option) any later version. -+* -+* This program is distributed in the hope that it will be useful, -+* but WITHOUT ANY WARRANTY; without even the implied warranty of -+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+* GNU General Public License for more details. -+* -+* You should have received a copy of the GNU General Public License -+* along with this program; if not, write to the Free Software -+* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+*/ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/mtd/physmap.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/at91rm9200_mc.h> -+ -+#include "generic.h" -+#include <linux/serial_8250.h> -+ -+ -+#define SERIAL_FLAGS (UPF_BOOT_AUTOCONF | UPF_IOREMAP| UPF_SHARE_IRQ) -+#define SERIAL_CLK (1843200) -+ -+ -+/*--------------------------------------------------------------------- -+ * External UART -+ */ -+ -+#define PORT(_base, _irq) \ -+ { \ -+ .mapbase = _base, \ -+ .irq = _irq, \ -+ .uartclk = SERIAL_CLK, \ -+ .iotype = UPIO_MEM, \ -+ .regshift = 0, \ -+ .flags = SERIAL_FLAGS, \ -+ } -+ -+static struct plat_serial8250_port tms_data[] = { -+ PORT(0x70000000, AT91_PIN_PC3), -+ PORT(0x80000000, AT91_PIN_PC5), -+ { }, -+}; -+ -+static struct platform_device tms_device = { -+ .name = "serial8250", -+ .id = PLAT8250_DEV_PLATFORM, -+ .dev = -+ { -+ .platform_data = &tms_data, -+ }, -+}; -+ -+static void setup_external_uart(void) -+{ -+ at91_sys_write(AT91_SMC_CSR(2), -+ AT91_SMC_ACSS_STD -+ | AT91_SMC_DBW_8 -+ | AT91_SMC_BAT -+ | AT91_SMC_WSEN -+ | AT91_SMC_NWS_(32) /* wait states */ -+ | AT91_SMC_RWSETUP_(6) /* setup time */ -+ | AT91_SMC_RWHOLD_(4) /* hold time */ -+ -+ ); -+ at91_sys_write(AT91_SMC_CSR(6), -+ AT91_SMC_ACSS_STD -+ | AT91_SMC_DBW_8 -+ | AT91_SMC_BAT -+ | AT91_SMC_WSEN -+ | AT91_SMC_NWS_(32) /* wait states */ -+ | AT91_SMC_RWSETUP_(6) /* setup time */ -+ | AT91_SMC_RWHOLD_(4) /* hold time */ -+ -+ ); -+ at91_sys_write(AT91_SMC_CSR(7), -+ AT91_SMC_ACSS_STD -+ | AT91_SMC_DBW_8 -+ | AT91_SMC_BAT -+ | AT91_SMC_WSEN -+ | AT91_SMC_NWS_(32) /* wait states */ -+ | AT91_SMC_RWSETUP_(6) /* setup time */ -+ | AT91_SMC_RWHOLD_(4) /* hold time */ -+ ); -+ -+ platform_device_register(&tms_device); -+} -+ -+ -+/* -+ * Serial port configuration. -+ * 0 .. 3 = USART0 .. USART3 -+ * 4 = DBGU -+ */ -+static struct at91_uart_config __initdata tms_uart_config = { -+ .console_tty = 0, /* ttyS0 */ -+ .nr_tty = 5, -+ .tty_map = { 4, 0, 1, 2, 3 } /* ttyS0, ..., ttyS4 */ -+}; -+ -+static void __init tms_map_io(void) -+{ -+ /* Initialize processor: 18.432 MHz crystal */ -+ at91rm9200_initialize(18432000, AT91RM9200_BGA); -+ -+ /* Setup the LEDs */ -+ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); -+ -+ /* Setup the serial ports and console */ -+ at91_init_serial(&tms_uart_config); -+} -+ -+static void __init tms_init_irq(void) -+{ -+ at91rm9200_init_interrupts(NULL); -+} -+ -+ -+static struct at91_eth_data __initdata tms_eth_data = { -+ .phy_irq_pin = AT91_PIN_PC4, -+ .is_rmii = 1, -+}; -+ -+static struct at91_usbh_data __initdata tms_usbh_data = { -+ .ports = 2, -+}; -+ -+static struct spi_board_info tms_spi_devices[] = { -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 15 * 1000 * 1000, -+ }, -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 1, -+ .max_speed_hz = 15 * 1000 * 1000, -+ } -+}; -+ -+static struct i2c_board_info __initdata tms_i2c_devices[] = { -+ { -+ I2C_BOARD_INFO("isl1208", 0x6f), -+ } -+}; -+ -+static void __init tms_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* Ethernet */ -+ at91_add_device_eth(&tms_eth_data); -+ at91_add_device_usbh(&tms_usbh_data); -+ /* I2C */ -+ at91_add_device_i2c(tms_i2c_devices, ARRAY_SIZE(tms_i2c_devices)); -+ /* SPI */ -+ at91_add_device_spi(tms_spi_devices, ARRAY_SIZE(tms_spi_devices)); -+ /* Two port external UART */ -+ setup_external_uart(); -+} -+ -+MACHINE_START(SWEDATMS, "Sweda TMS-100 Board") -+ /* Maintainer: Luiz de Barros */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91rm9200_timer, -+ .map_io = tms_map_io, -+ .init_irq = tms_init_irq, -+ .init_machine = tms_board_init, -+MACHINE_END ---- /dev/null -+++ b/arch/arm/mach-at91/board-tt9200.c -@@ -0,0 +1,192 @@ -+/* -+ * linux/arch/arm/mach-at91rm9200/board-tt9200.c -+ * Copyright (C) 2007 Toptechnology -+ * -+ * Based on board-ecbat91.c -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/spi/flash.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+ -+#include "generic.h" -+ -+ -+static void __init tt9200_map_io(void) -+{ -+ /* Initialize processor: 18.432 MHz crystal */ -+ at91rm9200_initialize(18432000, AT91RM9200_PQFP); -+ -+ /* Setup the LEDs */ -+ at91_init_leds(AT91_PIN_PB27, AT91_PIN_PB27); -+ -+ /* DBGU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART0 on ttyS1. (Rx & Tx only) */ -+ at91_register_uart(AT91RM9200_ID_US0, 1, 0); -+ -+ /* USART1 on ttyS2. (Rx & Tx only) */ -+ at91_register_uart(AT91RM9200_ID_US1, 2, 0); -+ -+ /* USART2 on ttyS3. (Rx & Tx only) */ -+ at91_register_uart(AT91RM9200_ID_US2, 3, 0); -+ -+ /* USART3 on ttyS4. (Rx, Tx, CTS, RTS) */ -+ at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS | ATMEL_UART_RTS); -+ -+ /* Console on ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); -+} -+ -+static void __init tt9200_init_irq(void) -+{ -+ at91rm9200_init_interrupts(NULL); -+} -+ -+static struct at91_eth_data __initdata tt9200_eth_data = { -+ .phy_irq_pin = AT91_PIN_PB29, -+ .is_rmii = 0, -+}; -+ -+static struct at91_usbh_data __initdata tt9200_usbh_data = { -+ .ports = 1, -+}; -+ -+static struct i2c_board_info __initdata tt9200_i2c_devices[] = { -+ { -+ I2C_BOARD_INFO("rtc-m41t80", 0x68), -+ .type = "m41t80", -+ } -+}; -+ -+static struct at91_mmc_data __initdata tt9200_mmc_data = { -+ .slot_b = 0, -+ .wire4 = 1, -+}; -+ -+ -+#if defined(CONFIG_MTD_DATAFLASH) -+static struct mtd_partition __initdata tt9200_flash_partitions[] = -+{ -+ { -+ .name = "Darrell", -+ .offset = 0, -+ .size = 12 * 1056, -+ }, -+ { -+ .name = "U-boot", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 110 * 1056, -+ }, -+ { -+ .name = "U-boot env", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 8 * 1056, -+ }, -+ { -+ .name = "Kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 1534 * 1056, -+ }, -+ { -+ .name = "Filesystem", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL, -+ } -+}; -+ -+static struct flash_platform_data __initdata tt9200_flash_platform = { -+ .name = "SPI Dataflash", -+ .parts = tt9200_flash_partitions, -+ .nr_parts = ARRAY_SIZE(tt9200_flash_partitions) -+}; -+ -+#endif -+ -+static struct spi_board_info __initdata tt9200_spi_devices[] = { -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ /* Errata #13 */ -+ .max_speed_hz = 5 * 1000 * 1000, -+ .bus_num = 0, -+#if defined(CONFIG_MTD_DATAFLASH) -+ .platform_data = &tt9200_flash_platform, -+#endif -+ }, -+}; -+ -+static struct gpio_led tt9200_leds[] = { -+ { -+ .name = "led0", -+ .gpio = AT91_PIN_PB27, -+ .active_low = 1, -+ .default_trigger = "heartbeat", -+ } -+}; -+ -+static void __init tt9200_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ -+ /* Ethernet */ -+ at91_add_device_eth(&tt9200_eth_data); -+ -+ /* USB Host */ -+ at91_add_device_usbh(&tt9200_usbh_data); -+ -+ /* I2C */ -+ at91_add_device_i2c(tt9200_i2c_devices, ARRAY_SIZE(tt9200_i2c_devices)); -+ -+ /* MMC */ -+ at91_add_device_mmc(0, &tt9200_mmc_data); -+ -+ /* LEDS */ -+ at91_gpio_leds(tt9200_leds, ARRAY_SIZE(tt9200_leds)); -+ -+ /* SPI */ -+ at91_add_device_spi(tt9200_spi_devices, ARRAY_SIZE(tt9200_spi_devices)); -+} -+ -+MACHINE_START(TT9200, "Toptech TT9200") -+ /* Maintainer: toptech.com.ar */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91rm9200_timer, -+ .map_io = tt9200_map_io, -+ .init_irq = tt9200_init_irq, -+ .init_machine = tt9200_board_init, -+MACHINE_END ---- /dev/null -+++ b/arch/arm/mach-at91/board-usb-a9260.c -@@ -0,0 +1,215 @@ -+/* -+ * linux/arch/arm/mach-at91/board-usb-a9260.c -+ * -+ * Copyright (C) 2005 SAN People -+ * Copyright (C) 2006 Atmel -+ * Copyright (C) 2007 Calao-systems -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/clk.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/at91_shdwc.h> -+ -+#include "generic.h" -+ -+ -+static void __init ek_map_io(void) -+{ -+ /* Initialize processor: 12.000 MHz crystal */ -+ at91sam9260_initialize(12000000); -+ -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); -+} -+ -+static void __init ek_init_irq(void) -+{ -+ at91sam9260_init_interrupts(NULL); -+} -+ -+ -+/* -+ * USB Host port -+ */ -+static struct at91_usbh_data __initdata ek_usbh_data = { -+ .ports = 2, -+}; -+ -+/* -+ * USB Device port -+ */ -+static struct at91_udc_data __initdata ek_udc_data = { -+ .vbus_pin = AT91_PIN_PC5, -+ .pullup_pin = 0, /* pull-up driven by UDC */ -+}; -+ -+/* -+ * MACB Ethernet device -+ */ -+static struct at91_eth_data __initdata ek_macb_data = { -+ .phy_irq_pin = AT91_PIN_PA31, -+ .is_rmii = 1, -+}; -+ -+/* -+ * NAND flash -+ */ -+static struct mtd_partition __initdata ek_nand_partition[] = { -+ { -+ .name = "Uboot & Kernel", -+ .offset = 0x00000000, -+ .size = 16 * 1024 * 1024, -+ }, -+ { -+ .name = "Root FS", -+ .offset = 0x01000000, -+ .size = 120 * 1024 * 1024, -+ }, -+ { -+ .name = "FS", -+ .offset = 0x08800000, -+ .size = 120 * 1024 * 1024, -+ } -+}; -+ -+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -+{ -+ *num_partitions = ARRAY_SIZE(ek_nand_partition); -+ return ek_nand_partition; -+} -+ -+static struct at91_nand_data __initdata ek_nand_data = { -+ .ale = 21, -+ .cle = 22, -+// .det_pin = ... not connected -+ .rdy_pin = AT91_PIN_PC13, -+ .enable_pin = AT91_PIN_PC14, -+ .partition_info = nand_partitions, -+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) -+ .bus_width_16 = 1, -+#else -+ .bus_width_16 = 0, -+#endif -+}; -+ -+/* -+ * GPIO Buttons -+ */ -+ -+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -+static struct gpio_keys_button ek_buttons[] = { -+ { /* USER PUSH BUTTON */ -+ .code = KEY_ENTER, -+ .gpio = AT91_PIN_PB10, -+ .active_low = 1, -+ .desc = "user_pb", -+ .wakeup = 1, -+ } -+}; -+ -+static struct gpio_keys_platform_data ek_button_data = { -+ .buttons = ek_buttons, -+ .nbuttons = ARRAY_SIZE(ek_buttons), -+}; -+ -+static struct platform_device ek_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &ek_button_data, -+ } -+}; -+ -+static void __init ek_add_device_buttons(void) -+{ -+ at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ -+ at91_set_deglitch(AT91_PIN_PB10, 1); -+ -+ platform_device_register(&ek_button_device); -+} -+#else -+static void __init ek_add_device_buttons(void) {} -+#endif -+ -+/* -+ * LEDs -+ */ -+static struct gpio_led ek_leds[] = { -+ { /* user_led (green) */ -+ .name = "user_led", -+ .gpio = AT91_PIN_PB21, -+ .active_low = 0, -+ .default_trigger = "heartbeat", -+ } -+}; -+ -+static void __init ek_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* USB Host */ -+ at91_add_device_usbh(&ek_usbh_data); -+ /* USB Device */ -+ at91_add_device_udc(&ek_udc_data); -+ /* NAND */ -+ at91_add_device_nand(&ek_nand_data); -+ /* I2C */ -+ at91_add_device_i2c(NULL, 0); -+ /* Ethernet */ -+ at91_add_device_eth(&ek_macb_data); -+ /* Push Buttons */ -+ ek_add_device_buttons(); -+ /* LEDs */ -+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); -+ /* shutdown controller, wakeup button (5 msec low) */ -+ at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW -+ | AT91_SHDW_RTTWKEN); -+} -+ -+MACHINE_START(USB_A9260, "CALAO USB_A9260") -+ /* Maintainer: calao-systems */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91sam926x_timer, -+ .map_io = ek_map_io, -+ .init_irq = ek_init_irq, -+ .init_machine = ek_board_init, -+MACHINE_END ---- /dev/null -+++ b/arch/arm/mach-at91/board-usb-a9263.c -@@ -0,0 +1,230 @@ -+/* -+ * linux/arch/arm/mach-at91/board-usb-a9263.c -+ * -+ * Copyright (C) 2005 SAN People -+ * Copyright (C) 2007 Atmel Corporation. -+ * Copyright (C) 2007 Calao-systems -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/at91_shdwc.h> -+ -+#include "generic.h" -+ -+ -+static void __init ek_map_io(void) -+{ -+ /* Initialize processor: 12.00 MHz crystal */ -+ at91sam9263_initialize(12000000); -+ -+ /* DGBU on ttyS0. (Rx & Tx only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* set serial console to ttyS0 (ie, DBGU) */ -+ at91_set_serial_console(0); -+} -+ -+static void __init ek_init_irq(void) -+{ -+ at91sam9263_init_interrupts(NULL); -+} -+ -+ -+/* -+ * USB Host port -+ */ -+static struct at91_usbh_data __initdata ek_usbh_data = { -+ .ports = 2, -+}; -+ -+/* -+ * USB Device port -+ */ -+static struct at91_udc_data __initdata ek_udc_data = { -+ .vbus_pin = AT91_PIN_PB11, -+ .pullup_pin = 0, /* pull-up driven by UDC */ -+}; -+ -+/* -+ * SPI devices. -+ */ -+static struct spi_board_info ek_spi_devices[] = { -+#if !defined(CONFIG_MMC_AT91) -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 15 * 1000 * 1000, -+ .bus_num = 0, -+ } -+#endif -+}; -+ -+/* -+ * MACB Ethernet device -+ */ -+static struct at91_eth_data __initdata ek_macb_data = { -+ .phy_irq_pin = AT91_PIN_PE31, -+ .is_rmii = 1, -+}; -+ -+/* -+ * NAND flash -+ */ -+static struct mtd_partition __initdata ek_nand_partition[] = { -+ { -+ .name = "Linux Kernel", -+ .offset = 0x00000000, -+ .size = 16 * 1024 * 1024, -+ }, -+ { -+ .name = "Root FS", -+ .offset = 0x01000000, -+ .size = 120 * 1024 * 1024, -+ }, -+ { -+ .name = "FS", -+ .offset = 0x08800000, -+ .size = 120 * 1024 * 1024, -+ } -+}; -+ -+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -+{ -+ *num_partitions = ARRAY_SIZE(ek_nand_partition); -+ return ek_nand_partition; -+} -+ -+static struct at91_nand_data __initdata ek_nand_data = { -+ .ale = 21, -+ .cle = 22, -+// .det_pin = ... not connected -+ .rdy_pin = AT91_PIN_PA22, -+ .enable_pin = AT91_PIN_PD15, -+ .partition_info = nand_partitions, -+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) -+ .bus_width_16 = 1, -+#else -+ .bus_width_16 = 0, -+#endif -+}; -+ -+/* -+ * GPIO Buttons -+ */ -+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -+static struct gpio_keys_button ek_buttons[] = { -+ { /* USER PUSH BUTTON */ -+ .code = KEY_ENTER, -+ .gpio = AT91_PIN_PB10, -+ .active_low = 1, -+ .desc = "user_pb", -+ .wakeup = 1, -+ } -+}; -+ -+static struct gpio_keys_platform_data ek_button_data = { -+ .buttons = ek_buttons, -+ .nbuttons = ARRAY_SIZE(ek_buttons), -+}; -+ -+static struct platform_device ek_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &ek_button_data, -+ } -+}; -+ -+static void __init ek_add_device_buttons(void) -+{ -+ at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ -+ at91_set_deglitch(AT91_PIN_PB10, 1); -+ -+ platform_device_register(&ek_button_device); -+} -+#else -+static void __init ek_add_device_buttons(void) {} -+#endif -+ -+/* -+ * LEDs -+ */ -+static struct gpio_led ek_leds[] = { -+ { /* user_led (green) */ -+ .name = "user_led", -+ .gpio = AT91_PIN_PB21, -+ .active_low = 1, -+ .default_trigger = "heartbeat", -+ } -+}; -+ -+ -+static void __init ek_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* USB Host */ -+ at91_add_device_usbh(&ek_usbh_data); -+ /* USB Device */ -+ at91_add_device_udc(&ek_udc_data); -+ /* SPI */ -+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); -+ /* Ethernet */ -+ at91_add_device_eth(&ek_macb_data); -+ /* NAND */ -+ at91_add_device_nand(&ek_nand_data); -+ /* I2C */ -+ at91_add_device_i2c(NULL, 0); -+ /* Push Buttons */ -+ ek_add_device_buttons(); -+ /* LEDs */ -+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); -+ /* shutdown controller, wakeup button (5 msec low) */ -+ at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW -+ | AT91_SHDW_RTTWKEN); -+} -+ -+MACHINE_START(USB_A9263, "CALAO USB_A9263") -+ /* Maintainer: calao-systems */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91sam926x_timer, -+ .map_io = ek_map_io, -+ .init_irq = ek_init_irq, -+ .init_machine = ek_board_init, -+MACHINE_END ---- a/arch/arm/mach-at91/clock.c -+++ b/arch/arm/mach-at91/clock.c -@@ -32,6 +32,7 @@ - #include <asm/arch/cpu.h> - - #include "clock.h" -+#include "generic.h" - - - /* -@@ -113,12 +114,34 @@ static void pmc_sys_mode(struct clk *clk - at91_sys_write(AT91_PMC_SCDR, clk->pmc_mask); - } - -+static void pmc_uckr_mode(struct clk *clk, int is_on) -+{ -+ unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR); -+ -+ if (is_on) { -+ is_on = AT91_PMC_LOCKU; -+ at91_sys_write(AT91_CKGR_UCKR, uckr | clk->pmc_mask); -+ } else -+ at91_sys_write(AT91_CKGR_UCKR, uckr & ~(clk->pmc_mask)); -+ -+ do { -+ cpu_relax(); -+ } while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKU) != is_on); -+} -+ - /* USB function clocks (PLLB must be 48 MHz) */ - static struct clk udpck = { - .name = "udpck", - .parent = &pllb, - .mode = pmc_sys_mode, - }; -+static struct clk utmi_clk = { -+ .name = "utmi_clk", -+ .parent = &main_clk, -+ .pmc_mask = AT91_PMC_UPLLEN, /* in CKGR_UCKR */ -+ .mode = pmc_uckr_mode, -+ .type = CLK_TYPE_PLL, -+}; - static struct clk uhpck = { - .name = "uhpck", - .parent = &pllb, -@@ -254,6 +277,23 @@ EXPORT_SYMBOL(clk_get_rate); - - /*------------------------------------------------------------------------*/ - -+#ifdef CONFIG_PM -+ -+int clk_must_disable(struct clk *clk) -+{ -+ if (!at91_suspend_entering_slow_clock()) -+ return 0; -+ -+ while (clk->parent) -+ clk = clk->parent; -+ return clk != &clk32k; -+} -+EXPORT_SYMBOL(clk_must_disable); -+ -+#endif -+ -+/*------------------------------------------------------------------------*/ -+ - #ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS - - /* -@@ -362,7 +402,7 @@ static void __init init_programmable_clo - - static int at91_clk_show(struct seq_file *s, void *unused) - { -- u32 scsr, pcsr, sr; -+ u32 scsr, pcsr, uckr = 0, sr; - struct clk *clk; - - seq_printf(s, "SCSR = %8x\n", scsr = at91_sys_read(AT91_PMC_SCSR)); -@@ -370,7 +410,10 @@ static int at91_clk_show(struct seq_file - seq_printf(s, "MOR = %8x\n", at91_sys_read(AT91_CKGR_MOR)); - seq_printf(s, "MCFR = %8x\n", at91_sys_read(AT91_CKGR_MCFR)); - seq_printf(s, "PLLA = %8x\n", at91_sys_read(AT91_CKGR_PLLAR)); -- seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR)); -+ if (!cpu_is_at91sam9rl()) -+ seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR)); -+ if (cpu_is_at91cap9() || cpu_is_at91sam9rl()) -+ seq_printf(s, "UCKR = %8x\n", uckr = at91_sys_read(AT91_CKGR_UCKR)); - seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR)); - seq_printf(s, "SR = %8x\n", sr = at91_sys_read(AT91_PMC_SR)); - -@@ -383,6 +426,8 @@ static int at91_clk_show(struct seq_file - state = (scsr & clk->pmc_mask) ? "on" : "off"; - else if (clk->mode == pmc_periph_mode) - state = (pcsr & clk->pmc_mask) ? "on" : "off"; -+ else if (clk->mode == pmc_uckr_mode) -+ state = (uckr & clk->pmc_mask) ? "on" : "off"; - else if (clk->pmc_mask) - state = (sr & clk->pmc_mask) ? "on" : "off"; - else if (clk == &clk32k || clk == &main_clk) -@@ -583,6 +628,17 @@ int __init at91_clock_init(unsigned long - uhpck.rate_hz = at91_usb_rate(&pllb, pllb.rate_hz, at91_pllb_usb_init); - - /* -+ * USB HS clock init -+ */ -+ if (cpu_is_at91cap9() || cpu_is_at91sam9rl()) { -+ /* -+ * multiplier is hard-wired to 40 -+ * (obtain the USB High Speed 480 MHz when input is 12 MHz) -+ */ -+ utmi_clk.rate_hz = 40 * utmi_clk.parent->rate_hz; -+ } -+ -+ /* - * MCK and CPU derive from one of those primary clocks. - * For now, assume this parentage won't change. - */ -@@ -599,6 +655,9 @@ int __init at91_clock_init(unsigned long - for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++) - list_add_tail(&standard_pmc_clocks[i]->node, &clocks); - -+ if (cpu_is_at91cap9() || cpu_is_at91sam9rl()) -+ list_add_tail(&utmi_clk.node, &clocks); -+ - /* MCK and CPU clock are "always on" */ - clk_enable(&mck); - ---- a/arch/arm/mach-at91/generic.h -+++ b/arch/arm/mach-at91/generic.h -@@ -41,6 +41,7 @@ extern void __init at91_clock_associate( - /* Power Management */ - extern void at91_irq_suspend(void); - extern void at91_irq_resume(void); -+extern int at91_suspend_entering_slow_clock(void); - - /* GPIO */ - #define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */ ---- a/arch/arm/mach-at91/gpio.c -+++ b/arch/arm/mach-at91/gpio.c -@@ -490,7 +490,8 @@ postcore_initcall(at91_gpio_debugfs_init - - /*--------------------------------------------------------------------------*/ - --/* This lock class tells lockdep that GPIO irqs are in a different -+/* -+ * This lock class tells lockdep that GPIO irqs are in a different - * category than their parents, so it won't report false recursion. - */ - static struct lock_class_key gpio_lock_class; -@@ -557,6 +558,7 @@ void __init at91_gpio_init(struct at91_g - data->regbase = data->offset + (void __iomem *)AT91_VA_BASE_SYS; - - /* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */ -+ /* AT91CAP9_ID_PIOABCD groups PIOA, PIOB, PIOC, PIOD */ - if (last && last->id == data->id) - last->next = data; - } ---- /dev/null -+++ b/arch/arm/mach-at91/ics1523.c -@@ -0,0 +1,208 @@ -+/* -+ * arch/arm/mach-at91rm9200/ics1523.c -+ * -+ * Copyright (C) 2003 ATMEL Rousset -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <asm/hardware.h> -+#include <asm/io.h> -+ -+#include <linux/clk.h> -+#include <linux/delay.h> -+#include <linux/err.h> -+#include <linux/init.h> -+#include <linux/kernel.h> -+ -+#include <asm/arch/ics1523.h> -+#include <asm/arch/at91_twi.h> -+#include <asm/arch/gpio.h> -+ -+/* TWI Errors */ -+#define AT91_TWI_ERROR (AT91_TWI_NACK | AT91_TWI_UNRE | AT91_TWI_OVRE) -+ -+ -+static void __iomem *twi_base; -+ -+#define at91_twi_read(reg) __raw_readl(twi_base + (reg)) -+#define at91_twi_write(reg, val) __raw_writel((val), twi_base + (reg)) -+ -+ -+/* ----------------------------------------------------------------------------- -+ * Initialization of TWI CLOCK -+ * ----------------------------------------------------------------------------- */ -+ -+static void at91_ics1523_SetTwiClock(unsigned int mck_khz) -+{ -+ int sclock; -+ -+ /* Here, CKDIV = 1 and CHDIV = CLDIV ==> CLDIV = CHDIV = 1/4*((Fmclk/FTWI) -6) */ -+ sclock = (10*mck_khz / ICS_TRANSFER_RATE); -+ if (sclock % 10 >= 5) -+ sclock = (sclock /10) - 5; -+ else -+ sclock = (sclock /10)- 6; -+ sclock = (sclock + (4 - sclock %4)) >> 2; /* div 4 */ -+ -+ at91_twi_write(AT91_TWI_CWGR, 0x00010000 | sclock | (sclock << 8)); -+} -+ -+/* ----------------------------------------------------------------------------- -+ * Read a byte with TWI Interface from the Clock Generator ICS1523 -+ * ----------------------------------------------------------------------------- */ -+ -+static int at91_ics1523_ReadByte(unsigned char reg_address, unsigned char *data_in) -+{ -+ int Status, nb_trial; -+ -+ at91_twi_write(AT91_TWI_MMR, AT91_TWI_MREAD | AT91_TWI_IADRSZ_1 | ((ICS_ADDR << 16) & AT91_TWI_DADR)); -+ at91_twi_write(AT91_TWI_IADR, reg_address); -+ at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP); -+ -+ /* Program temporizing period (300us) */ -+ udelay(300); -+ -+ /* Wait TXcomplete ... */ -+ nb_trial = 0; -+ Status = at91_twi_read(AT91_TWI_SR); -+ while (!(Status & AT91_TWI_TXCOMP) && (nb_trial < 10)) { -+ nb_trial++; -+ Status = at91_twi_read(AT91_TWI_SR); -+ } -+ -+ if (Status & AT91_TWI_TXCOMP) { -+ *data_in = (unsigned char) at91_twi_read(AT91_TWI_RHR); -+ return ICS1523_ACCESS_OK; -+ } -+ else -+ return ICS1523_ACCESS_ERROR; -+} -+ -+/* ----------------------------------------------------------------------------- -+ * Write a byte with TWI Interface to the Clock Generator ICS1523 -+ * ----------------------------------------------------------------------------- */ -+ -+static int at91_ics1523_WriteByte(unsigned char reg_address, unsigned char data_out) -+{ -+ int Status, nb_trial; -+ -+ at91_twi_write(AT91_TWI_MMR, AT91_TWI_IADRSZ_1 | ((ICS_ADDR << 16) & AT91_TWI_DADR)); -+ at91_twi_write(AT91_TWI_IADR, reg_address); -+ at91_twi_write(AT91_TWI_THR, data_out); -+ at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP); -+ -+ /* Program temporizing period (300us) */ -+ udelay(300); -+ -+ nb_trial = 0; -+ Status = at91_twi_read(AT91_TWI_SR); -+ while (!(Status & AT91_TWI_TXCOMP) && (nb_trial < 10)) { -+ nb_trial++; -+ if (Status & AT91_TWI_ERROR) { -+ /* If Underrun OR NACK - Start again */ -+ at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP); -+ -+ /* Program temporizing period (300us) */ -+ udelay(300); -+ } -+ Status = at91_twi_read(AT91_TWI_SR); -+ }; -+ -+ if (Status & AT91_TWI_TXCOMP) -+ return ICS1523_ACCESS_OK; -+ else -+ return ICS1523_ACCESS_ERROR; -+} -+ -+/* ----------------------------------------------------------------------------- -+ * Initialization of the Clock Generator ICS1523 -+ * ----------------------------------------------------------------------------- */ -+ -+int at91_ics1523_init(void) -+{ -+ int nb_trial; -+ int ack = ICS1523_ACCESS_OK; -+ unsigned int status = 0xffffffff; -+ struct clk *twi_clk; -+ -+ /* Map in TWI peripheral */ -+ twi_base = ioremap(AT91RM9200_BASE_TWI, SZ_16K); -+ if (!twi_base) -+ return -ENOMEM; -+ -+ /* pins used for TWI interface */ -+ at91_set_A_periph(AT91_PIN_PA25, 0); /* TWD */ -+ at91_set_multi_drive(AT91_PIN_PA25, 1); -+ at91_set_A_periph(AT91_PIN_PA26, 0); /* TWCK */ -+ at91_set_multi_drive(AT91_PIN_PA26, 1); -+ -+ /* Enable the TWI clock */ -+ twi_clk = clk_get(NULL, "twi_clk"); -+ if (IS_ERR(twi_clk)) -+ return ICS1523_ACCESS_ERROR; -+ clk_enable(twi_clk); -+ -+ /* Disable interrupts */ -+ at91_twi_write(AT91_TWI_IDR, -1); -+ -+ /* Reset peripheral */ -+ at91_twi_write(AT91_TWI_CR, AT91_TWI_SWRST); -+ -+ /* Set Master mode */ -+ at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN); -+ -+ /* Set TWI Clock Waveform Generator Register */ -+ at91_ics1523_SetTwiClock(60000); /* MCK in KHz = 60000 KHz */ -+ -+ /* ICS1523 Initialisation */ -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_ICR, (unsigned char) 0); -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_OE, (unsigned char) (ICS_OEF | ICS_OET2 | ICS_OETCK)); -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_OD, (unsigned char) (ICS_INSEL | 0x7F)); -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAO, (unsigned char) 0); -+ -+ nb_trial = 0; -+ do { -+ nb_trial++; -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_ICR, (unsigned char) (ICS_ENDLS | ICS_ENPLS | ICS_PDEN /*| ICS_FUNCSEL*/)); -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_LCR, (unsigned char) (ICS_PSD | ICS_PFD)); -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_FD0, (unsigned char) 0x39) ; /* 0x7A */ -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_FD1, (unsigned char) 0x00); -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_SWRST, (unsigned char) (ICS_PLLR)); -+ -+ /* Program 1ms temporizing period */ -+ mdelay(1); -+ -+ at91_ics1523_ReadByte ((unsigned char) ICS_SR, (char *)&status); -+ } while (!((unsigned int) status & (unsigned int) ICS_PLLLOCK) && (nb_trial < 10)); -+ -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAC, (unsigned char) 0x03) ; /* 0x01 */ -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_SWRST, (unsigned char) (ICS_DPAR)); -+ -+ /* Program 1ms temporizing period */ -+ mdelay(1); -+ -+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAO, (unsigned char) 0x00); -+ -+ /* Program 1ms temporizing period */ -+ mdelay(1); -+ -+ /* All done - cleanup */ -+ iounmap(twi_base); -+ clk_disable(twi_clk); -+ clk_put(twi_clk); -+ -+ return ack; -+} ---- a/arch/arm/mach-at91/pm.c -+++ b/arch/arm/mach-at91/pm.c -@@ -26,12 +26,144 @@ - #include <asm/mach-types.h> - - #include <asm/arch/at91_pmc.h> --#include <asm/arch/at91rm9200_mc.h> - #include <asm/arch/gpio.h> - #include <asm/arch/cpu.h> - - #include "generic.h" - -+#ifdef CONFIG_ARCH_AT91RM9200 -+#include <asm/arch/at91rm9200_mc.h> -+ -+/* -+ * The AT91RM9200 goes into self-refresh mode with this command, and will -+ * terminate self-refresh automatically on the next SDRAM access. -+ */ -+#define sdram_selfrefresh_enable() at91_sys_write(AT91_SDRAMC_SRR, 1) -+#define sdram_selfrefresh_disable() do {} while (0) -+ -+#elif defined(CONFIG_ARCH_AT91CAP9) -+#include <asm/arch/at91cap9_ddrsdr.h> -+ -+static u32 saved_lpr; -+ -+static inline void sdram_selfrefresh_enable(void) -+{ -+ u32 lpr; -+ -+ saved_lpr = at91_sys_read(AT91_DDRSDRC_LPR); -+ -+ lpr = saved_lpr & ~AT91_DDRSDRC_LPCB; -+ at91_sys_write(AT91_DDRSDRC_LPR, lpr | AT91_DDRSDRC_LPCB_SELF_REFRESH); -+} -+ -+#define sdram_selfrefresh_disable() at91_sys_write(AT91_DDRSDRC_LPR, saved_lpr) -+ -+#else -+#include <asm/arch/at91sam9_sdramc.h> -+ -+#ifdef CONFIG_ARCH_AT91SAM9263 -+/* -+ * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use; -+ * handle those cases both here and in the Suspend-To-RAM support. -+ */ -+#define AT91_SDRAMC AT91_SDRAMC0 -+#warning Assuming EB1 SDRAM controller is *NOT* used -+#endif -+ -+static u32 saved_lpr; -+ -+static inline void sdram_selfrefresh_enable(void) -+{ -+ u32 lpr; -+ -+ saved_lpr = at91_sys_read(AT91_SDRAMC_LPR); -+ -+ lpr = saved_lpr & ~AT91_SDRAMC_LPCB; -+ at91_sys_write(AT91_SDRAMC_LPR, lpr | AT91_SDRAMC_LPCB_SELF_REFRESH); -+} -+ -+#define sdram_selfrefresh_disable() at91_sys_write(AT91_SDRAMC_LPR, saved_lpr) -+ -+/* -+ * FIXME: The AT91SAM9263 has a second EBI controller which may have -+ * additional SDRAM. pm_slowclock.S will require a similar fix. -+ */ -+ -+#endif -+ -+ -+/* -+ * Show the reason for the previous system reset. -+ */ -+#if defined(AT91_SHDWC) -+ -+#include <asm/arch/at91_rstc.h> -+#include <asm/arch/at91_shdwc.h> -+ -+static void __init show_reset_status(void) -+{ -+ static char reset[] __initdata = "reset"; -+ -+ static char general[] __initdata = "general"; -+ static char wakeup[] __initdata = "wakeup"; -+ static char watchdog[] __initdata = "watchdog"; -+ static char software[] __initdata = "software"; -+ static char user[] __initdata = "user"; -+ static char unknown[] __initdata = "unknown"; -+ -+ static char signal[] __initdata = "signal"; -+ static char rtc[] __initdata = "rtc"; -+ static char rtt[] __initdata = "rtt"; -+ static char restore[] __initdata = "power-restored"; -+ -+ char *reason, *r2 = reset; -+ u32 reset_type, wake_type; -+ -+ reset_type = at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_RSTTYP; -+ wake_type = at91_sys_read(AT91_SHDW_SR); -+ -+ switch (reset_type) { -+ case AT91_RSTC_RSTTYP_GENERAL: -+ reason = general; -+ break; -+ case AT91_RSTC_RSTTYP_WAKEUP: -+ /* board-specific code enabled the wakeup sources */ -+ reason = wakeup; -+ -+ /* "wakeup signal" */ -+ if (wake_type & AT91_SHDW_WAKEUP0) -+ r2 = signal; -+ else { -+ r2 = reason; -+ if (wake_type & AT91_SHDW_RTTWK) /* rtt wakeup */ -+ reason = rtt; -+ else if (wake_type & AT91_SHDW_RTCWK) /* rtc wakeup */ -+ reason = rtc; -+ else if (wake_type == 0) /* power-restored wakeup */ -+ reason = restore; -+ else /* unknown wakeup */ -+ reason = unknown; -+ } -+ break; -+ case AT91_RSTC_RSTTYP_WATCHDOG: -+ reason = watchdog; -+ break; -+ case AT91_RSTC_RSTTYP_SOFTWARE: -+ reason = software; -+ break; -+ case AT91_RSTC_RSTTYP_USER: -+ reason = user; -+ break; -+ default: -+ reason = unknown; -+ break; -+ } -+ pr_info("AT91: Starting after %s %s\n", reason, r2); -+} -+#else -+static void __init show_reset_status(void) {} -+#endif -+ - - static int at91_pm_valid_state(suspend_state_t state) - { -@@ -62,6 +194,7 @@ static int at91_pm_begin(suspend_state_t - * Verify that all the clocks are correct before entering - * slow-clock mode. - */ -+#warning "This should probably be moved to clocks.c" - static int at91_pm_verify_clocks(void) - { - unsigned long scsr; -@@ -107,24 +240,24 @@ static int at91_pm_verify_clocks(void) - } - - /* -- * Call this from platform driver suspend() to see how deeply to suspend. -+ * This is called from clk_must_disable(), to see how deeply to suspend. - * For example, some controllers (like OHCI) need one of the PLL clocks - * in order to act as a wakeup source, and those are not available when - * going into slow clock mode. -- * -- * REVISIT: generalize as clk_will_be_available(clk)? Other platforms have -- * the very same problem (but not using at91 main_clk), and it'd be better -- * to add one generic API rather than lots of platform-specific ones. - */ - int at91_suspend_entering_slow_clock(void) - { - return (target_state == PM_SUSPEND_MEM); - } --EXPORT_SYMBOL(at91_suspend_entering_slow_clock); - - - static void (*slow_clock)(void); - -+#ifdef CONFIG_AT91_SLOW_CLOCK -+extern void at91_slow_clock(void); -+extern u32 at91_slow_clock_sz; -+#endif -+ - - static int at91_pm_enter(suspend_state_t state) - { -@@ -158,11 +291,14 @@ static int at91_pm_enter(suspend_state_t - * turning off the main oscillator; reverse on wakeup. - */ - if (slow_clock) { -+#ifdef CONFIG_AT91_SLOW_CLOCK -+ /* copy slow_clock handler to SRAM, and call it */ -+ memcpy(slow_clock, at91_slow_clock, at91_slow_clock_sz); -+#endif - slow_clock(); - break; - } else { -- /* DEVELOPMENT ONLY */ -- pr_info("AT91: PM - no slow clock mode yet ...\n"); -+ pr_info("AT91: PM - no slow clock mode enabled ...\n"); - /* FALLTHROUGH leaving master clock alone */ - } - -@@ -175,13 +311,15 @@ static int at91_pm_enter(suspend_state_t - case PM_SUSPEND_STANDBY: - /* - * NOTE: the Wait-for-Interrupt instruction needs to be -- * in icache so the SDRAM stays in self-refresh mode until -- * the wakeup IRQ occurs. -+ * in icache so no SDRAM accesses are needed until the -+ * wakeup IRQ occurs and self-refresh is terminated. - */ - asm("b 1f; .align 5; 1:"); - asm("mcr p15, 0, r0, c7, c10, 4"); /* drain write buffer */ -- at91_sys_write(AT91_SDRAMC_SRR, 1); /* self-refresh mode */ -- /* fall though to next state */ -+ sdram_selfrefresh_enable(); -+ asm("mcr p15, 0, r0, c7, c0, 4"); /* wait for interrupt */ -+ sdram_selfrefresh_disable(); -+ break; - - case PM_SUSPEND_ON: - asm("mcr p15, 0, r0, c7, c0, 4"); /* wait for interrupt */ -@@ -196,6 +334,7 @@ static int at91_pm_enter(suspend_state_t - at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR)); - - error: -+ sdram_selfrefresh_disable(); - target_state = PM_SUSPEND_ON; - at91_irq_resume(); - at91_gpio_resume(); -@@ -220,21 +359,20 @@ static struct platform_suspend_ops at91_ - - static int __init at91_pm_init(void) - { -- printk("AT91: Power Management\n"); -- --#ifdef CONFIG_AT91_PM_SLOW_CLOCK -- /* REVISIT allocations of SRAM should be dynamically managed. -- * FIQ handlers and other components will want SRAM/TCM too... -- */ -- slow_clock = (void *) (AT91_VA_BASE_SRAM + (3 * SZ_4K)); -- memcpy(slow_clock, at91rm9200_slow_clock, at91rm9200_slow_clock_sz); -+#ifdef CONFIG_AT91_SLOW_CLOCK -+ slow_clock = (void *) (AT91_IO_VIRT_BASE - at91_slow_clock_sz); - #endif - -- /* Disable SDRAM low-power mode. Cannot be used with self-refresh. */ -+ pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : "")); -+ -+#ifdef CONFIG_ARCH_AT91RM9200 -+ /* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */ - at91_sys_write(AT91_SDRAMC_LPR, 0); -+#endif - - suspend_set_ops(&at91_pm_ops); - -+ show_reset_status(); - return 0; - } - arch_initcall(at91_pm_init); ---- /dev/null -+++ b/arch/arm/mach-at91/pm_slowclock.S -@@ -0,0 +1,283 @@ -+/* -+ * arch/arm/mach-at91/pm_slow_clock.S -+ * -+ * Copyright (C) 2006 Savin Zlobec -+ * -+ * AT91SAM9 support: -+ * Copyright (C) 2007 Anti Sullin <anti.sullin@artecdesign.ee -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ * -+ */ -+ -+#include <linux/linkage.h> -+#include <asm/hardware.h> -+#include <asm/arch/at91_pmc.h> -+ -+#ifdef CONFIG_ARCH_AT91RM9200 -+#include <asm/arch/at91rm9200_mc.h> -+#elif defined(CONFIG_ARCH_AT91CAP9) -+#include <asm/arch/at91cap9_ddrsdr.h> -+#else -+#include <asm/arch/at91sam9_sdramc.h> -+#endif -+ -+ -+#ifdef CONFIG_ARCH_AT91SAM9263 -+/* -+ * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use; -+ * handle those cases both here and in the Suspend-To-RAM support. -+ */ -+#define AT91_SDRAMC AT91_SDRAMC0 -+#warning Assuming EB1 SDRAM controller is *NOT* used -+#endif -+ -+/* -+ * When SLOWDOWN_MASTER_CLOCK is defined we will also slow down the Master -+ * clock during suspend by adjusting its prescalar and divisor. -+ * NOTE: This hasn't been shown to be stable on SAM9s; and on the RM9200 there -+ * are errata regarding adjusting the prescalar and divisor. -+ */ -+#undef SLOWDOWN_MASTER_CLOCK -+ -+#define MCKRDY_TIMEOUT 1000 -+#define MOSCRDY_TIMEOUT 1000 -+#define PLLALOCK_TIMEOUT 1000 -+#define PLLBLOCK_TIMEOUT 1000 -+ -+ -+/* -+ * Wait until master clock is ready (after switching master clock source) -+ */ -+ .macro wait_mckrdy -+ mov r4, #MCKRDY_TIMEOUT -+1: sub r4, r4, #1 -+ cmp r4, #0 -+ beq 2f -+ ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)] -+ tst r3, #AT91_PMC_MCKRDY -+ beq 1b -+2: -+ .endm -+ -+/* -+ * Wait until master oscillator has stabilized. -+ */ -+ .macro wait_moscrdy -+ mov r4, #MOSCRDY_TIMEOUT -+1: sub r4, r4, #1 -+ cmp r4, #0 -+ beq 2f -+ ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)] -+ tst r3, #AT91_PMC_MOSCS -+ beq 1b -+2: -+ .endm -+ -+/* -+ * Wait until PLLA has locked. -+ */ -+ .macro wait_pllalock -+ mov r4, #PLLALOCK_TIMEOUT -+1: sub r4, r4, #1 -+ cmp r4, #0 -+ beq 2f -+ ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)] -+ tst r3, #AT91_PMC_LOCKA -+ beq 1b -+2: -+ .endm -+ -+/* -+ * Wait until PLLB has locked. -+ */ -+ .macro wait_pllblock -+ mov r4, #PLLBLOCK_TIMEOUT -+1: sub r4, r4, #1 -+ cmp r4, #0 -+ beq 2f -+ ldr r3, [r1, #(AT91_PMC_SR - AT91_PMC)] -+ tst r3, #AT91_PMC_LOCKB -+ beq 1b -+2: -+ .endm -+ -+ .text -+ -+ENTRY(at91_slow_clock) -+ /* Save registers on stack */ -+ stmfd sp!, {r0 - r12, lr} -+ -+ /* -+ * Register usage: -+ * R1 = Base address of AT91_PMC -+ * R2 = Base address of AT91_SDRAMC (or AT91_SYS on AT91RM9200) -+ * R3 = temporary register -+ * R4 = temporary register -+ */ -+ ldr r1, .at91_va_base_pmc -+ ldr r2, .at91_va_base_sdramc -+ -+ /* Drain write buffer */ -+ mcr p15, 0, r0, c7, c10, 4 -+ -+#ifdef CONFIG_ARCH_AT91RM9200 -+ /* Put SDRAM in self-refresh mode */ -+ mov r3, #1 -+ str r3, [r2, #AT91_SDRAMC_SRR] -+#elif defined(CONFIG_ARCH_AT91CAP9) -+ /* Enable SDRAM self-refresh mode */ -+ ldr r3, [r2, #AT91_DDRSDRC_LPR - AT91_DDRSDRC] -+ str r3, .saved_sam9_lpr -+ -+ mov r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH -+ str r3, [r2, #AT91_DDRSDRC_LPR - AT91_DDRSDRC] -+#else -+ /* Enable SDRAM self-refresh mode */ -+ ldr r3, [r2, #AT91_SDRAMC_LPR - AT91_SDRAMC] -+ str r3, .saved_sam9_lpr -+ -+ mov r3, #AT91_SDRAMC_LPCB_SELF_REFRESH -+ str r3, [r2, #AT91_SDRAMC_LPR - AT91_SDRAMC] -+#endif -+ -+ /* Save Master clock setting */ -+ ldr r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)] -+ str r3, .saved_mckr -+ -+ /* -+ * Set the Master clock source to slow clock -+ */ -+ bic r3, r3, #AT91_PMC_CSS -+ str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)] -+ -+ wait_mckrdy -+ -+#ifdef SLOWDOWN_MASTER_CLOCK -+ /* -+ * Set the Master Clock PRES and MDIV fields. -+ * -+ * See AT91RM9200 errata #27 and #28 for details. -+ */ -+ mov r3, #0 -+ str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)] -+ -+ wait_mckrdy -+#endif -+ -+ /* Save PLLA setting and disable it */ -+ ldr r3, [r1, #(AT91_CKGR_PLLAR - AT91_PMC)] -+ str r3, .saved_pllar -+ -+ mov r3, #AT91_PMC_PLLCOUNT -+ orr r3, r3, #(1 << 29) /* bit 29 always set */ -+ str r3, [r1, #(AT91_CKGR_PLLAR - AT91_PMC)] -+ -+ wait_pllalock -+ -+ /* Save PLLB setting and disable it */ -+ ldr r3, [r1, #(AT91_CKGR_PLLBR - AT91_PMC)] -+ str r3, .saved_pllbr -+ -+ mov r3, #AT91_PMC_PLLCOUNT -+ str r3, [r1, #(AT91_CKGR_PLLBR - AT91_PMC)] -+ -+ wait_pllblock -+ -+ /* Turn off the main oscillator */ -+ ldr r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)] -+ bic r3, r3, #AT91_PMC_MOSCEN -+ str r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)] -+ -+ /* Wait for interrupt */ -+ mcr p15, 0, r0, c7, c0, 4 -+ -+ /* Turn on the main oscillator */ -+ ldr r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)] -+ orr r3, r3, #AT91_PMC_MOSCEN -+ str r3, [r1, #(AT91_CKGR_MOR - AT91_PMC)] -+ -+ wait_moscrdy -+ -+ /* Restore PLLB setting */ -+ ldr r3, .saved_pllbr -+ str r3, [r1, #(AT91_CKGR_PLLBR - AT91_PMC)] -+ -+ wait_pllblock -+ -+ /* Restore PLLA setting */ -+ ldr r3, .saved_pllar -+ str r3, [r1, #(AT91_CKGR_PLLAR - AT91_PMC)] -+ -+ wait_pllalock -+ -+#ifdef SLOWDOWN_MASTER_CLOCK -+ /* -+ * First set PRES if it was not 0, -+ * than set CSS and MDIV fields. -+ * -+ * See AT91RM9200 errata #27 and #28 for details. -+ */ -+ ldr r3, .saved_mckr -+ tst r3, #AT91_PMC_PRES -+ beq 2f -+ and r3, r3, #AT91_PMC_PRES -+ str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)] -+ -+ wait_mckrdy -+#endif -+ -+ /* -+ * Restore master clock setting -+ */ -+2: ldr r3, .saved_mckr -+ str r3, [r1, #(AT91_PMC_MCKR - AT91_PMC)] -+ -+ wait_mckrdy -+ -+#ifdef CONFIG_ARCH_AT91RM9200 -+ /* Do nothing - self-refresh is automatically disabled. */ -+#elif defined(CONFIG_ARCH_AT91CAP9) -+ /* Restore LPR on AT91CAP9 */ -+ ldr r3, .saved_sam9_lpr -+ str r3, [r2, #AT91_DDRSDRC_LPR - AT91_DDRSDRC] -+#else -+ /* Restore LPR on AT91SAM9 */ -+ ldr r3, .saved_sam9_lpr -+ str r3, [r2, #AT91_SDRAMC_LPR - AT91_SDRAMC] -+#endif -+ -+ /* Restore registers, and return */ -+ ldmfd sp!, {r0 - r12, pc} -+ -+ -+.saved_mckr: -+ .word 0 -+ -+.saved_pllar: -+ .word 0 -+ -+.saved_pllbr: -+ .word 0 -+ -+.saved_sam9_lpr: -+ .word 0 -+ -+.at91_va_base_pmc: -+ .word AT91_VA_BASE_SYS + AT91_PMC -+ -+#ifdef CONFIG_ARCH_AT91RM9200 -+.at91_va_base_sdramc: -+ .word AT91_VA_BASE_SYS -+#elif defined(CONFIG_ARCH_AT91CAP9) -+.at91_va_base_sdramc: -+ .word AT91_VA_BASE_SYS + AT91_DDRSDRC -+#else -+.at91_va_base_sdramc: -+ .word AT91_VA_BASE_SYS + AT91_SDRAMC -+#endif -+ -+ENTRY(at91_slow_clock_sz) -+ .word .-at91_slow_clock ---- a/arch/arm/mach-ks8695/Makefile -+++ b/arch/arm/mach-ks8695/Makefile -@@ -11,5 +11,8 @@ obj- := - # PCI support is optional - obj-$(CONFIG_PCI) += pci.o - -+# LEDs -+obj-$(CONFIG_LEDS) += leds.o -+ - # Board-specific support - obj-$(CONFIG_MACH_KS8695) += board-micrel.o ---- a/arch/arm/mach-ks8695/devices.c -+++ b/arch/arm/mach-ks8695/devices.c -@@ -176,6 +176,27 @@ static void __init ks8695_add_device_wat - #endif - - -+/* -------------------------------------------------------------------- -+ * LEDs -+ * -------------------------------------------------------------------- */ -+ -+#if defined(CONFIG_LEDS) -+short ks8695_leds_cpu = -1; -+short ks8695_leds_timer = -1; -+ -+void __init ks8695_init_leds(u8 cpu_led, u8 timer_led) -+{ -+ /* Enable GPIO to access the LEDs */ -+ gpio_direction_output(cpu_led, 1); -+ gpio_direction_output(timer_led, 1); -+ -+ ks8695_leds_cpu = cpu_led; -+ ks8695_leds_timer = timer_led; -+} -+#else -+void __init ks8695_init_leds(u8 cpu_led, u8 timer_led) {} -+#endif -+ - /* -------------------------------------------------------------------- */ - - /* ---- a/arch/arm/mach-ks8695/gpio.c -+++ b/arch/arm/mach-ks8695/gpio.c -@@ -136,9 +136,9 @@ int __init_or_module gpio_direction_outp - /* set line state */ - x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPD); - if (state) -- x |= (1 << pin); -+ x |= IOPD_(pin); - else -- x &= ~(1 << pin); -+ x &= ~IOPD_(pin); - __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPD); - - /* set pin as output */ -@@ -168,9 +168,9 @@ void gpio_set_value(unsigned int pin, un - /* set output line state */ - x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPD); - if (state) -- x |= (1 << pin); -+ x |= IOPD_(pin); - else -- x &= ~(1 << pin); -+ x &= ~IOPD_(pin); - __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPD); - - local_irq_restore(flags); -@@ -189,7 +189,7 @@ int gpio_get_value(unsigned int pin) - return -EINVAL; - - x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPD); -- return (x & (1 << pin)) != 0; -+ return (x & IOPD_(pin)) != 0; - } - EXPORT_SYMBOL(gpio_get_value); - ---- /dev/null -+++ b/arch/arm/mach-ks8695/leds.c -@@ -0,0 +1,94 @@ -+/* -+ * LED driver for KS8695-based boards. -+ * -+ * Copyright (C) Andrew Victor -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/module.h> -+#include <linux/init.h> -+ -+#include <asm/mach-types.h> -+#include <asm/leds.h> -+#include <asm/arch/devices.h> -+#include <asm/arch/gpio.h> -+ -+ -+static inline void ks8695_led_on(unsigned int led) -+{ -+ gpio_set_value(led, 0); -+} -+ -+static inline void ks8695_led_off(unsigned int led) -+{ -+ gpio_set_value(led, 1); -+} -+ -+static inline void ks8695_led_toggle(unsigned int led) -+{ -+ unsigned long is_off = gpio_get_value(led); -+ if (is_off) -+ ks8695_led_on(led); -+ else -+ ks8695_led_off(led); -+} -+ -+ -+/* -+ * Handle LED events. -+ */ -+static void ks8695_leds_event(led_event_t evt) -+{ -+ unsigned long flags; -+ -+ local_irq_save(flags); -+ -+ switch(evt) { -+ case led_start: /* System startup */ -+ ks8695_led_on(ks8695_leds_cpu); -+ break; -+ -+ case led_stop: /* System stop / suspend */ -+ ks8695_led_off(ks8695_leds_cpu); -+ break; -+ -+#ifdef CONFIG_LEDS_TIMER -+ case led_timer: /* Every 50 timer ticks */ -+ ks8695_led_toggle(ks8695_leds_timer); -+ break; -+#endif -+ -+#ifdef CONFIG_LEDS_CPU -+ case led_idle_start: /* Entering idle state */ -+ ks8695_led_off(ks8695_leds_cpu); -+ break; -+ -+ case led_idle_end: /* Exit idle state */ -+ ks8695_led_on(ks8695_leds_cpu); -+ break; -+#endif -+ -+ default: -+ break; -+ } -+ -+ local_irq_restore(flags); -+} -+ -+ -+static int __init leds_init(void) -+{ -+ if ((ks8695_leds_timer == -1) || (ks8695_leds_cpu == -1)) -+ return -ENODEV; -+ -+ leds_event = ks8695_leds_event; -+ -+ leds_event(led_start); -+ return 0; -+} -+ -+__initcall(leds_init); ---- a/arch/arm/mach-ks8695/pci.c -+++ b/arch/arm/mach-ks8695/pci.c -@@ -141,7 +141,7 @@ static struct pci_ops ks8695_pci_ops = { - .write = ks8695_pci_writeconfig, - }; - --static struct pci_bus *ks8695_pci_scan_bus(int nr, struct pci_sys_data *sys) -+static struct pci_bus* __init ks8695_pci_scan_bus(int nr, struct pci_sys_data *sys) - { - return pci_scan_bus(sys->busnr, &ks8695_pci_ops, sys); - } ---- a/drivers/char/Kconfig -+++ b/drivers/char/Kconfig -@@ -1056,5 +1056,21 @@ config DEVPORT - - source "drivers/s390/char/Kconfig" - -+config AT91_SPI -+ bool "SPI driver (legacy) for AT91RM9200 processors" -+ depends on ARCH_AT91RM9200 -+ default y -+ help -+ The SPI driver gives access to this serial bus on the AT91RM9200 -+ processor. -+ -+config AT91_SPIDEV -+ bool "SPI device interface (legacy) for AT91RM9200 processors" -+ depends on ARCH_AT91RM9200 && AT91_SPI -+ default n -+ help -+ The SPI driver gives user mode access to this serial -+ bus on the AT91RM9200 processor. -+ - endmenu - ---- a/drivers/char/Makefile -+++ b/drivers/char/Makefile -@@ -98,6 +98,8 @@ obj-$(CONFIG_GPIO_DEVICE) += gpio_dev.o - obj-$(CONFIG_GPIO_VR41XX) += vr41xx_giu.o - obj-$(CONFIG_GPIO_TB0219) += tb0219.o - obj-$(CONFIG_TELCLOCK) += tlclk.o -+obj-$(CONFIG_AT91_SPI) += at91_spi.o -+obj-$(CONFIG_AT91_SPIDEV) += at91_spidev.o - - obj-$(CONFIG_MWAVE) += mwave/ - obj-$(CONFIG_AGP) += agp/ ---- /dev/null -+++ b/drivers/char/at91_spi.c -@@ -0,0 +1,337 @@ -+/* -+ * Serial Peripheral Interface (SPI) driver for the Atmel AT91RM9200 (Thunder) -+ * -+ * Copyright (C) SAN People (Pty) Ltd -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version -+ * 2 of the License, or (at your option) any later version. -+ */ -+ -+#include <linux/init.h> -+#include <linux/dma-mapping.h> -+#include <linux/module.h> -+#include <linux/sched.h> -+#include <linux/completion.h> -+#include <linux/interrupt.h> -+#include <linux/clk.h> -+#include <linux/platform_device.h> -+#include <linux/atmel_pdc.h> -+#include <asm/io.h> -+#include <asm/semaphore.h> -+ -+#include <asm/arch/at91_spi.h> -+#include <asm/arch/board.h> -+#include <asm/arch/spi.h> -+ -+#undef DEBUG_SPI -+ -+static struct spi_local spi_dev[NR_SPI_DEVICES]; /* state of the SPI devices */ -+static int spi_enabled = 0; -+static struct semaphore spi_lock; /* protect access to SPI bus */ -+static int current_device = -1; /* currently selected SPI device */ -+static struct clk *spi_clk; /* SPI clock */ -+static void __iomem *spi_base; /* SPI peripheral base-address */ -+ -+DECLARE_COMPLETION(transfer_complete); -+ -+ -+#define at91_spi_read(reg) __raw_readl(spi_base + (reg)) -+#define at91_spi_write(reg, val) __raw_writel((val), spi_base + (reg)) -+ -+ -+/* ......................................................................... */ -+ -+/* -+ * Access and enable the SPI bus. -+ * This MUST be called before any transfers are performed. -+ */ -+void spi_access_bus(short device) -+{ -+ /* Ensure that requested device is valid */ -+ if ((device < 0) || (device >= NR_SPI_DEVICES)) -+ panic("at91_spi: spi_access_bus called with invalid device"); -+ -+ if (spi_enabled == 0) { -+ clk_enable(spi_clk); /* Enable Peripheral clock */ -+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIEN); /* Enable SPI */ -+#ifdef DEBUG_SPI -+ printk("SPI on\n"); -+#endif -+ } -+ spi_enabled++; -+ -+ /* Lock the SPI bus */ -+ down(&spi_lock); -+ current_device = device; -+ -+ /* Configure SPI bus for device */ -+ at91_spi_write(AT91_SPI_MR, AT91_SPI_MSTR | AT91_SPI_MODFDIS | (spi_dev[device].pcs << 16)); -+} -+ -+/* -+ * Relinquish control of the SPI bus. -+ */ -+void spi_release_bus(short device) -+{ -+ if (device != current_device) -+ panic("at91_spi: spi_release called with invalid device"); -+ -+ /* Release the SPI bus */ -+ current_device = -1; -+ up(&spi_lock); -+ -+ spi_enabled--; -+ if (spi_enabled == 0) { -+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIDIS); /* Disable SPI */ -+ clk_disable(spi_clk); /* Disable Peripheral clock */ -+#ifdef DEBUG_SPI -+ printk("SPI off\n"); -+#endif -+ } -+} -+ -+/* -+ * Perform a data transfer over the SPI bus -+ */ -+int spi_transfer(struct spi_transfer_list* list) -+{ -+ struct spi_local *device = (struct spi_local *) &spi_dev[current_device]; -+ int tx_size; -+ -+ if (!list) -+ panic("at91_spi: spi_transfer called with NULL transfer list"); -+ if (current_device == -1) -+ panic("at91_spi: spi_transfer called without acquiring bus"); -+ -+#ifdef DEBUG_SPI -+ printk("SPI transfer start [%i]\n", list->nr_transfers); -+#endif -+ -+ /* If we are in 16-bit mode, we need to modify what we pass to the PDC */ -+ tx_size = (at91_spi_read(AT91_SPI_CSR(current_device)) & AT91_SPI_BITS_16) ? 2 : 1; -+ -+ /* Store transfer list */ -+ device->xfers = list; -+ list->curr = 0; -+ -+ /* Assume there must be at least one transfer */ -+ device->tx = dma_map_single(NULL, list->tx[0], list->txlen[0], DMA_TO_DEVICE); -+ device->rx = dma_map_single(NULL, list->rx[0], list->rxlen[0], DMA_FROM_DEVICE); -+ -+ /* Program PDC registers */ -+ at91_spi_write(ATMEL_PDC_TPR, device->tx); -+ at91_spi_write(ATMEL_PDC_RPR, device->rx); -+ at91_spi_write(ATMEL_PDC_TCR, list->txlen[0] / tx_size); -+ at91_spi_write(ATMEL_PDC_RCR, list->rxlen[0] / tx_size); -+ -+ /* Is there a second transfer? */ -+ if (list->nr_transfers > 1) { -+ device->txnext = dma_map_single(NULL, list->tx[1], list->txlen[1], DMA_TO_DEVICE); -+ device->rxnext = dma_map_single(NULL, list->rx[1], list->rxlen[1], DMA_FROM_DEVICE); -+ -+ /* Program Next PDC registers */ -+ at91_spi_write(ATMEL_PDC_TNPR, device->txnext); -+ at91_spi_write(ATMEL_PDC_RNPR, device->rxnext); -+ at91_spi_write(ATMEL_PDC_TNCR, list->txlen[1] / tx_size); -+ at91_spi_write(ATMEL_PDC_RNCR, list->rxlen[1] / tx_size); -+ } -+ else { -+ device->txnext = 0; -+ device->rxnext = 0; -+ at91_spi_write(ATMEL_PDC_TNCR, 0); -+ at91_spi_write(ATMEL_PDC_RNCR, 0); -+ } -+ -+ // TODO: If we are doing consecutive transfers (at high speed, or -+ // small buffers), then it might be worth modifying the 'Delay between -+ // Consecutive Transfers' in the CSR registers. -+ // This is an issue if we cannot chain the next buffer fast enough -+ // in the interrupt handler. -+ -+ /* Enable transmitter and receiver */ -+ at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN | ATMEL_PDC_TXTEN); -+ -+ at91_spi_write(AT91_SPI_IER, AT91_SPI_ENDRX); /* enable buffer complete interrupt */ -+ wait_for_completion(&transfer_complete); -+ -+#ifdef DEBUG_SPI -+ printk("SPI transfer end\n"); -+#endif -+ -+ return 0; -+} -+ -+/* ......................................................................... */ -+ -+/* -+ * Handle interrupts from the SPI controller. -+ */ -+static irqreturn_t at91spi_interrupt(int irq, void *dev_id) -+{ -+ unsigned int status; -+ struct spi_local *device = (struct spi_local *) &spi_dev[current_device]; -+ struct spi_transfer_list *list = device->xfers; -+ -+#ifdef DEBUG_SPI -+ printk("SPI interrupt %i\n", current_device); -+#endif -+ -+ if (!list) -+ panic("at91_spi: spi_interrupt with a NULL transfer list"); -+ -+ status = at91_spi_read(AT91_SPI_SR) & at91_spi_read(AT91_SPI_IMR); /* read status */ -+ -+ dma_unmap_single(NULL, device->tx, list->txlen[list->curr], DMA_TO_DEVICE); -+ dma_unmap_single(NULL, device->rx, list->rxlen[list->curr], DMA_FROM_DEVICE); -+ -+ device->tx = device->txnext; /* move next transfer to current transfer */ -+ device->rx = device->rxnext; -+ -+ list->curr = list->curr + 1; -+ if (list->curr == list->nr_transfers) { /* all transfers complete */ -+ at91_spi_write(AT91_SPI_IDR, AT91_SPI_ENDRX); /* disable interrupt */ -+ -+ /* Disable transmitter and receiver */ -+ at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS); -+ -+ device->xfers = NULL; -+ complete(&transfer_complete); -+ } -+ else if (list->curr+1 == list->nr_transfers) { /* no more next transfers */ -+ device->txnext = 0; -+ device->rxnext = 0; -+ at91_spi_write(ATMEL_PDC_TNCR, 0); -+ at91_spi_write(ATMEL_PDC_RNCR, 0); -+ } -+ else { -+ int i = (list->curr)+1; -+ -+ /* If we are in 16-bit mode, we need to modify what we pass to the PDC */ -+ int tx_size = (at91_spi_read(AT91_SPI_CSR(current_device)) & AT91_SPI_BITS_16) ? 2 : 1; -+ -+ device->txnext = dma_map_single(NULL, list->tx[i], list->txlen[i], DMA_TO_DEVICE); -+ device->rxnext = dma_map_single(NULL, list->rx[i], list->rxlen[i], DMA_FROM_DEVICE); -+ at91_spi_write(ATMEL_PDC_TNPR, device->txnext); -+ at91_spi_write(ATMEL_PDC_RNPR, device->rxnext); -+ at91_spi_write(ATMEL_PDC_TNCR, list->txlen[i] / tx_size); -+ at91_spi_write(ATMEL_PDC_RNCR, list->rxlen[i] / tx_size); -+ } -+ return IRQ_HANDLED; -+} -+ -+/* ......................................................................... */ -+ -+/* -+ * Initialize the SPI controller -+ */ -+static int __init at91spi_probe(struct platform_device *pdev) -+{ -+ int i; -+ unsigned long scbr; -+ struct resource *res; -+ -+ init_MUTEX(&spi_lock); -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ if (!res) -+ return -ENXIO; -+ -+ if (!request_mem_region(res->start, res->end - res->start + 1, "at91_spi")) -+ return -EBUSY; -+ -+ spi_base = ioremap(res->start, res->end - res->start + 1); -+ if (!spi_base) { -+ release_mem_region(res->start, res->end - res->start + 1); -+ return -ENOMEM; -+ } -+ -+ spi_clk = clk_get(NULL, "spi_clk"); -+ if (IS_ERR(spi_clk)) { -+ printk(KERN_ERR "at91_spi: no clock defined\n"); -+ iounmap(spi_base); -+ release_mem_region(res->start, res->end - res->start + 1); -+ return -ENODEV; -+ } -+ -+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SWRST); /* software reset of SPI controller */ -+ -+ /* -+ * Calculate the correct SPI baud-rate divisor. -+ */ -+ scbr = clk_get_rate(spi_clk) / (2 * DEFAULT_SPI_CLK); -+ scbr = scbr + 1; /* round up */ -+ -+ printk(KERN_INFO "at91_spi: Baud rate set to %ld\n", clk_get_rate(spi_clk) / (2 * scbr)); -+ -+ /* Set Chip Select registers to good defaults */ -+ for (i = 0; i < 4; i++) { -+ at91_spi_write(AT91_SPI_CSR(i), AT91_SPI_CPOL | AT91_SPI_BITS_8 | (16 << 16) | (scbr << 8)); -+ } -+ -+ at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS); -+ -+ memset(&spi_dev, 0, sizeof(spi_dev)); -+ spi_dev[0].pcs = 0xE; -+ spi_dev[1].pcs = 0xD; -+ spi_dev[2].pcs = 0xB; -+ spi_dev[3].pcs = 0x7; -+ -+ if (request_irq(AT91RM9200_ID_SPI, at91spi_interrupt, 0, "spi", NULL)) { -+ clk_put(spi_clk); -+ iounmap(spi_base); -+ release_mem_region(res->start, res->end - res->start + 1); -+ return -EBUSY; -+ } -+ -+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIEN); /* Enable SPI */ -+ -+ return 0; -+} -+ -+static int __devexit at91spi_remove(struct platform_device *pdev) -+{ -+ struct resource *res; -+ -+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIDIS); /* Disable SPI */ -+ clk_put(spi_clk); -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ iounmap(spi_base); -+ release_mem_region(res->start, res->end - res->start + 1); -+ -+ free_irq(AT91RM9200_ID_SPI, 0); -+ return 0; -+} -+ -+static struct platform_driver at91spi_driver = { -+ .probe = at91spi_probe, -+ .remove = __devexit_p(at91spi_remove), -+ .driver = { -+ .name = "at91_spi", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+static int __init at91spi_init(void) -+{ -+ return platform_driver_register(&at91spi_driver); -+} -+ -+static void __exit at91spi_exit(void) -+{ -+ platform_driver_unregister(&at91spi_driver); -+} -+ -+EXPORT_SYMBOL(spi_access_bus); -+EXPORT_SYMBOL(spi_release_bus); -+EXPORT_SYMBOL(spi_transfer); -+ -+module_init(at91spi_init); -+module_exit(at91spi_exit); -+ -+MODULE_LICENSE("GPL") -+MODULE_AUTHOR("Andrew Victor") -+MODULE_DESCRIPTION("SPI driver for Atmel AT91RM9200") -+MODULE_ALIAS("platform:at91_spi"); ---- /dev/null -+++ b/drivers/char/at91_spidev.c -@@ -0,0 +1,233 @@ -+/* -+ * User-space interface to the SPI bus on Atmel AT91RM9200 -+ * -+ * Copyright (C) 2003 SAN People (Pty) Ltd -+ * -+ * Based on SPI driver by Rick Bronson -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version -+ * 2 of the License, or (at your option) any later version. -+ */ -+ -+#include <linux/module.h> -+#include <linux/init.h> -+#include <linux/slab.h> -+#include <linux/highmem.h> -+#include <linux/pagemap.h> -+#include <asm/arch/spi.h> -+ -+#ifdef CONFIG_DEVFS_FS -+#include <linux/devfs_fs_kernel.h> -+#endif -+ -+ -+#undef DEBUG_SPIDEV -+ -+/* ......................................................................... */ -+ -+/* -+ * Read or Write to SPI bus. -+ */ -+static ssize_t spidev_rd_wr(struct file *file, char *buf, size_t count, loff_t *offset) -+{ -+ unsigned int spi_device = (unsigned int) file->private_data; -+ -+ struct mm_struct * mm; -+ struct page ** maplist; -+ struct spi_transfer_list* list; -+ int pgcount; -+ -+ unsigned int ofs, pagelen; -+ int res, i, err; -+ -+ if (!count) { -+ return 0; -+ } -+ -+ list = kmalloc(sizeof(struct spi_transfer_list), GFP_KERNEL); -+ if (!list) { -+ return -ENOMEM; -+ } -+ -+ mm = current->mm; -+ -+ pgcount = ((unsigned long)buf+count+PAGE_SIZE-1)/PAGE_SIZE - (unsigned long)buf/PAGE_SIZE; -+ -+ if (pgcount >= MAX_SPI_TRANSFERS) { -+ kfree(list); -+ return -EFBIG; -+ } -+ -+ maplist = kmalloc (pgcount * sizeof (struct page *), GFP_KERNEL); -+ -+ if (!maplist) { -+ kfree(list); -+ return -ENOMEM; -+ } -+ flush_cache_all(); -+ down_read(&mm->mmap_sem); -+ err= get_user_pages(current, mm, (unsigned long)buf, pgcount, 1, 0, maplist, NULL); -+ up_read(&mm->mmap_sem); -+ -+ if (err < 0) { -+ kfree(list); -+ kfree(maplist); -+ return err; -+ } -+ pgcount = err; -+ -+#ifdef DEBUG_SPIDEV -+ printk("spidev_rd_rw: %i %i\n", count, pgcount); -+#endif -+ -+ /* Set default return value = transfer length */ -+ res = count; -+ -+ /* -+ * At this point, the virtual area buf[0] .. buf[count-1] will have -+ * corresponding pages mapped in the physical memory and locked until -+ * we unmap the kiobuf. The pages cannot be swapped out or moved -+ * around. -+ */ -+ ofs = (unsigned long) buf & (PAGE_SIZE -1); -+ pagelen = PAGE_SIZE - ofs; -+ if (count < pagelen) -+ pagelen = count; -+ -+ for (i = 0; i < pgcount; i++) { -+ flush_dcache_page(maplist[i]); -+ -+ list->tx[i] = list->rx[i] = page_address(maplist[i]) + ofs; -+ list->txlen[i] = list->rxlen[i] = pagelen; -+ -+#ifdef DEBUG_SPIDEV -+ printk(" %i: %x (%i)\n", i, list->tx[i], list->txlen[i]); -+#endif -+ -+ ofs = 0; /* all subsequent transfers start at beginning of a page */ -+ count = count - pagelen; -+ pagelen = (count < PAGE_SIZE) ? count : PAGE_SIZE; -+ } -+ list->nr_transfers = pgcount; -+ -+ /* Perform transfer on SPI bus */ -+ spi_access_bus(spi_device); -+ spi_transfer(list); -+ spi_release_bus(spi_device); -+ -+ while (pgcount--) { -+ page_cache_release (maplist[pgcount]); -+ } -+ flush_cache_all(); -+ -+ kfree(maplist); -+ kfree(list); -+ -+ return res; -+} -+ -+static int spidev_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg) -+{ -+ int spi_device = MINOR(inode->i_rdev); -+ -+ if (spi_device >= NR_SPI_DEVICES) -+ return -ENODEV; -+ -+ // TODO: This interface can be used to configure the SPI bus. -+ // Configurable options could include: Speed, Clock Polarity, Clock Phase -+ -+ switch(cmd) { -+ default: -+ return -ENOIOCTLCMD; -+ } -+} -+ -+/* -+ * Open the SPI device -+ */ -+static int spidev_open(struct inode *inode, struct file *file) -+{ -+ unsigned int spi_device = MINOR(inode->i_rdev); -+ -+ if (spi_device >= NR_SPI_DEVICES) -+ return -ENODEV; -+ -+ /* -+ * 'private_data' is actually a pointer, but we overload it with the -+ * value we want to store. -+ */ -+ file->private_data = (void *)spi_device; -+ -+ return 0; -+} -+ -+/* -+ * Close the SPI device -+ */ -+static int spidev_close(struct inode *inode, struct file *file) -+{ -+ return 0; -+} -+ -+/* ......................................................................... */ -+ -+static struct file_operations spidev_fops = { -+ .owner = THIS_MODULE, -+ .llseek = no_llseek, -+ .read = spidev_rd_wr, -+ .write = (int (*) (struct file *file, const char *buf, size_t count, loff_t *offset))spidev_rd_wr, -+ .ioctl = spidev_ioctl, -+ .open = spidev_open, -+ .release = spidev_close, -+}; -+ -+/* -+ * Install the SPI /dev interface driver -+ */ -+static int __init at91_spidev_init(void) -+{ -+#ifdef CONFIG_DEVFS_FS -+ int i; -+#endif -+ -+ if (register_chrdev(SPI_MAJOR, "spi", &spidev_fops)) { -+ printk(KERN_ERR "at91_spidev: Unable to get major %d for SPI bus\n", SPI_MAJOR); -+ return -EIO; -+ } -+ -+#ifdef CONFIG_DEVFS_FS -+ devfs_mk_dir("spi"); -+ for (i = 0; i < NR_SPI_DEVICES; i++) { -+ devfs_mk_cdev(MKDEV(SPI_MAJOR, i), S_IFCHR | S_IRUSR | S_IWUSR, "spi/%d",i); -+ } -+#endif -+ printk(KERN_INFO "AT91 SPI driver loaded\n"); -+ -+ return 0; -+} -+ -+/* -+ * Remove the SPI /dev interface driver -+ */ -+static void __exit at91_spidev_exit(void) -+{ -+#ifdef CONFIG_DEVFS_FS -+ int i; -+ for (i = 0; i < NR_SPI_DEVICES; i++) { -+ devfs_remove("spi/%d", i); -+ } -+ -+ devfs_remove("spi"); -+#endif -+ -+ unregister_chrdev(SPI_MAJOR, "spi"); -+} -+ -+module_init(at91_spidev_init); -+module_exit(at91_spidev_exit); -+ -+MODULE_LICENSE("GPL") -+MODULE_AUTHOR("Andrew Victor") -+MODULE_DESCRIPTION("SPI /dev interface for Atmel AT91RM9200") ---- a/drivers/i2c/busses/Kconfig -+++ b/drivers/i2c/busses/Kconfig -@@ -88,6 +88,14 @@ config I2C_AT91 - to support combined I2C messages. Use the i2c-gpio driver - unless your system can cope with those limitations. - -+config I2C_AT91_CLOCKRATE -+ prompt "Atmel AT91 I2C/TWI clock-rate" -+ depends on I2C_AT91 -+ int -+ default 100000 -+ help -+ Set the AT91 I2C/TWI clock-rate. -+ - config I2C_AU1550 - tristate "Au1550/Au1200 SMBus interface" - depends on SOC_AU1550 || SOC_AU1200 -@@ -626,6 +634,14 @@ config I2C_VOODOO3 - This driver can also be built as a module. If so, the module - will be called i2c-voodoo3. - -+config I2C_PCA -+ tristate "PCA9564" -+ depends on I2C -+ select I2C_ALGOPCA -+ help -+ This driver support the Philips PCA 9564 Parallel bus to I2C -+ bus controller. -+ - config I2C_PCA_ISA - tristate "PCA9564 on an ISA bus" - depends on ISA ---- a/drivers/i2c/busses/Makefile -+++ b/drivers/i2c/busses/Makefile -@@ -29,6 +29,7 @@ obj-$(CONFIG_I2C_OMAP) += i2c-omap.o - obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o - obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-parport-light.o - obj-$(CONFIG_I2C_PASEMI) += i2c-pasemi.o -+obj-$(CONFIG_I2C_PCA) += i2c-pca.o - obj-$(CONFIG_I2C_PCA_ISA) += i2c-pca-isa.o - obj-$(CONFIG_I2C_PIIX4) += i2c-piix4.o - obj-$(CONFIG_I2C_PMCMSP) += i2c-pmcmsp.o ---- a/drivers/i2c/busses/i2c-at91.c -+++ b/drivers/i2c/busses/i2c-at91.c -@@ -31,8 +31,11 @@ - #include <asm/arch/board.h> - #include <asm/arch/cpu.h> - --#define TWI_CLOCK 100000 /* Hz. max 400 Kbits/sec */ - -+/* Clockrate is configurable - max 400 Kbits/sec */ -+static unsigned int clockrate = CONFIG_I2C_AT91_CLOCKRATE; -+module_param(clockrate, uint, 0); -+MODULE_PARM_DESC(clockrate, "The TWI clockrate"); - - static struct clk *twi_clk; - static void __iomem *twi_base; -@@ -53,7 +56,7 @@ static void __devinit at91_twi_hwinit(vo - at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN); /* Set Master mode */ - - /* Calcuate clock dividers */ -- cdiv = (clk_get_rate(twi_clk) / (2 * TWI_CLOCK)) - 3; -+ cdiv = (clk_get_rate(twi_clk) / (2 * clockrate)) - 3; - cdiv = cdiv + 1; /* round up */ - ckdiv = 0; - while (cdiv > 255) { -@@ -61,11 +64,12 @@ static void __devinit at91_twi_hwinit(vo - cdiv = cdiv >> 1; - } - -- if (cpu_is_at91rm9200()) { /* AT91RM9200 Errata #22 */ -- if (ckdiv > 5) { -- printk(KERN_ERR "AT91 I2C: Invalid TWI_CLOCK value!\n"); -- ckdiv = 5; -- } -+ if (cpu_is_at91rm9200() && (ckdiv > 5)) { /* AT91RM9200 Errata #22 */ -+ printk(KERN_ERR "AT91 I2C: Invalid TWI clockrate!\n"); -+ ckdiv = 5; -+ } else if (ckdiv > 7) { -+ printk(KERN_ERR "AT91 I2C: Invalid TWI clockrate!\n"); -+ ckdiv = 7; - } - - at91_twi_write(AT91_TWI_CWGR, (ckdiv << 16) | (cdiv << 8) | cdiv); ---- /dev/null -+++ b/drivers/i2c/busses/i2c-pca.c -@@ -0,0 +1,213 @@ -+/* -+ * Platform driver for PCA9564 I2C bus controller. -+ * -+ * (C) 2006 Andrew Victor -+ * -+ * Based on i2c-pca-isa.c driver for PCA9564 on ISA boards -+ * Copyright (C) 2004 Arcom Control Systems -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/module.h> -+#include <linux/moduleparam.h> -+#include <linux/delay.h> -+#include <linux/init.h> -+#include <linux/interrupt.h> -+#include <linux/wait.h> -+#include <linux/platform_device.h> -+ -+#include <linux/i2c.h> -+#include <linux/i2c-algo-pca.h> -+ -+#include <asm/io.h> -+ -+#include "../algos/i2c-algo-pca.h" -+ -+#define PCA_OWN_ADDRESS 0x55 /* our address for slave mode */ -+#define PCA_CLOCK I2C_PCA_CON_59kHz -+ -+//#define REG_SHIFT 2 -+#define REG_SHIFT 0 -+ -+//#define DEBUG_IO -+ -+#define PCA_IO_SIZE 4 -+ -+static void __iomem *base_addr; -+static int irq; -+static wait_queue_head_t pca_wait; -+ -+static int pca_getown(struct i2c_algo_pca_data *adap) -+{ -+ return PCA_OWN_ADDRESS; -+} -+ -+static int pca_getclock(struct i2c_algo_pca_data *adap) -+{ -+ return PCA_CLOCK; -+} -+ -+static void pca_writebyte(struct i2c_algo_pca_data *adap, int reg, int val) -+{ -+#ifdef DEBUG_IO -+ static char *names[] = { "T/O", "DAT", "ADR", "CON" }; -+ printk("*** write %s at %#lx <= %#04x\n", names[reg], (unsigned long) base_addr+reg, val); -+#endif -+ udelay(1); -+ outb(val, base_addr + (reg << REG_SHIFT)); -+} -+ -+static int pca_readbyte(struct i2c_algo_pca_data *adap, int reg) -+{ -+ int res; -+ -+ udelay(1); -+ res = inb(base_addr + (reg << REG_SHIFT)); -+#ifdef DEBUG_IO -+ { -+ static char *names[] = { "STA", "DAT", "ADR", "CON" }; -+ printk("*** read %s => %#04x\n", names[reg], res); -+ } -+#endif -+ return res; -+} -+ -+static int pca_waitforinterrupt(struct i2c_algo_pca_data *adap) -+{ -+ int ret = 0; -+ -+ if (irq > -1) { -+ ret = wait_event_interruptible(pca_wait, -+ pca_readbyte(adap, I2C_PCA_CON) & I2C_PCA_CON_SI); -+ } else { -+ while ((pca_readbyte(adap, I2C_PCA_CON) & I2C_PCA_CON_SI) == 0) -+ udelay(100); -+ } -+ return ret; -+} -+ -+static irqreturn_t pca_handler(int this_irq, void *dev_id) -+{ -+ wake_up_interruptible(&pca_wait); -+ return IRQ_HANDLED; -+} -+ -+static struct i2c_algo_pca_data pca_i2c_data = { -+ .get_own = pca_getown, -+ .get_clock = pca_getclock, -+ .write_byte = pca_writebyte, -+ .read_byte = pca_readbyte, -+ .wait_for_interrupt = pca_waitforinterrupt, -+}; -+ -+static struct i2c_adapter pca_i2c_ops = { -+ .owner = THIS_MODULE, -+ .id = I2C_HW_A_PLAT, -+ .algo_data = &pca_i2c_data, -+ .name = "PCA9564", -+ .class = I2C_CLASS_HWMON, -+}; -+ -+static int __devinit pca_i2c_probe(struct platform_device *pdev) -+{ -+ struct resource *res; -+ -+ init_waitqueue_head(&pca_wait); -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ if (!res) -+ return -ENODEV; -+ -+ if (!request_mem_region(res->start, PCA_IO_SIZE, "PCA9564")) -+ return -ENXIO; -+ -+ base_addr = ioremap(res->start, PCA_IO_SIZE); -+ if (base_addr == NULL) -+ goto out_region; -+ -+ irq = platform_get_irq(pdev, 0); -+ if (irq > -1) { -+ if (request_irq(irq, pca_handler, 0, "pca9564", NULL) < 0) { -+ printk(KERN_ERR "i2c-pca: Request irq%d failed\n", irq); -+ goto out_remap; -+ } -+ } -+ -+ /* set up the driverfs linkage to our parent device */ -+ pca_i2c_ops.dev.parent = &pdev->dev; -+ -+ if (i2c_pca_add_bus(&pca_i2c_ops) < 0) { -+ printk(KERN_ERR "i2c-pca: Failed to add i2c bus\n"); -+ goto out_irq; -+ } -+ -+ return 0; -+ -+ out_irq: -+ if (irq > -1) -+ free_irq(irq, &pca_i2c_ops); -+ -+ out_remap: -+ iounmap(base_addr); -+ -+ out_region: -+ release_mem_region(res->start, PCA_IO_SIZE); -+ return -ENODEV; -+} -+ -+static int __devexit pca_i2c_remove(struct platform_device *pdev) -+{ -+ struct resource *res; -+ -+ i2c_del_adapter(&pca_i2c_ops); -+ -+ if (irq > 0) -+ free_irq(irq, NULL); -+ -+ iounmap(base_addr); -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ release_mem_region(res->start, PCA_IO_SIZE); -+ -+ return 0; -+} -+ -+static struct platform_driver pca_i2c_driver = { -+ .probe = pca_i2c_probe, -+ .remove = __devexit_p(pca_i2c_remove), -+ .driver = { -+ .name = "pca9564", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+static int __init pca_i2c_init(void) -+{ -+ return platform_driver_register(&pca_i2c_driver); -+} -+ -+static void __exit pca_i2c_exit(void) -+{ -+ platform_driver_unregister(&pca_i2c_driver); -+} -+ -+module_init(pca_i2c_init); -+module_exit(pca_i2c_exit); -+ -+MODULE_AUTHOR("Andrew Victor"); -+MODULE_DESCRIPTION("PCA9564 platform driver"); -+MODULE_LICENSE("GPL"); ---- a/drivers/mmc/host/at91_mci.c -+++ b/drivers/mmc/host/at91_mci.c -@@ -659,13 +659,14 @@ static void at91_mci_set_ios(struct mmc_ - /* maybe switch power to the card */ - if (host->board->vcc_pin) { - switch (ios->power_mode) { -- case MMC_POWER_OFF: -- gpio_set_value(host->board->vcc_pin, 0); -- break; -- case MMC_POWER_UP: -- case MMC_POWER_ON: -- gpio_set_value(host->board->vcc_pin, 1); -- break; -+ case MMC_POWER_OFF: -+ gpio_set_value(host->board->vcc_pin, 0); -+ break; -+ case MMC_POWER_UP: -+ gpio_set_value(host->board->vcc_pin, 1); -+ break; -+ default: -+ break; - } - } - } ---- a/drivers/mtd/devices/Kconfig -+++ b/drivers/mtd/devices/Kconfig -@@ -270,5 +270,17 @@ config MTD_DOCPROBE_55AA - LinuxBIOS or if you need to recover a DiskOnChip Millennium on which - you have managed to wipe the first block. - --endmenu -+config MTD_AT91_DATAFLASH -+ tristate "AT91RM9200 DataFlash AT45DBxxx (legacy driver)" -+ depends on MTD && ARCH_AT91RM9200 && AT91_SPI -+ help -+ This enables access to the DataFlash (AT45DBxxx) on the AT91RM9200. -+ If you have such a board, say 'Y'. -+ -+config DATAFLASH_ALWAYS_ADD_DEVICE -+ bool "Register whole DataFlash device" -+ depends on MTD_AT91_DATAFLASH -+ help -+ Always add the whole DataFlash device when using MTD partitions. - -+endmenu ---- a/drivers/mtd/devices/Makefile -+++ b/drivers/mtd/devices/Makefile -@@ -17,3 +17,4 @@ obj-$(CONFIG_MTD_LART) += lart.o - obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd.o - obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o - obj-$(CONFIG_MTD_M25P80) += m25p80.o -+obj-$(CONFIG_MTD_AT91_DATAFLASH)+= at91_dataflash.o ---- /dev/null -+++ b/drivers/mtd/devices/at91_dataflash.c -@@ -0,0 +1,673 @@ -+/* -+ * Atmel DataFlash driver for Atmel AT91RM9200 (Thunder) -+ * -+ * Copyright (C) SAN People (Pty) Ltd -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version -+ * 2 of the License, or (at your option) any later version. -+*/ -+ -+#include <linux/module.h> -+#include <linux/init.h> -+#include <linux/slab.h> -+#include <linux/pci.h> -+#include <linux/mtd/mtd.h> -+#include <linux/mtd/partitions.h> -+ -+#include <asm/mach-types.h> -+ -+#include <asm/arch/spi.h> -+ -+ -+#undef DEBUG_DATAFLASH -+ -+#define DATAFLASH_MAX_DEVICES 4 /* max number of dataflash devices */ -+ -+#define OP_READ_CONTINUOUS 0xE8 -+#define OP_READ_PAGE 0xD2 -+#define OP_READ_BUFFER1 0xD4 -+#define OP_READ_BUFFER2 0xD6 -+#define OP_READ_STATUS 0xD7 -+ -+#define OP_ERASE_PAGE 0x81 -+#define OP_ERASE_BLOCK 0x50 -+ -+#define OP_TRANSFER_BUF1 0x53 -+#define OP_TRANSFER_BUF2 0x55 -+#define OP_COMPARE_BUF1 0x60 -+#define OP_COMPARE_BUF2 0x61 -+ -+#define OP_PROGRAM_VIA_BUF1 0x82 -+#define OP_PROGRAM_VIA_BUF2 0x85 -+ -+struct dataflash_local -+{ -+ int spi; /* SPI chip-select number */ -+ -+ unsigned int page_size; /* number of bytes per page */ -+ unsigned short page_offset; /* page offset in flash address */ -+}; -+ -+ -+/* Detected DataFlash devices */ -+static struct mtd_info* mtd_devices[DATAFLASH_MAX_DEVICES]; -+static int nr_devices = 0; -+ -+/* ......................................................................... */ -+ -+#ifdef CONFIG_MTD_PARTITIONS -+ -+static struct mtd_partition static_partitions_2M[] = -+{ -+ { -+ .name = "bootloader", -+ .offset = 0, -+ .size = 1 * 32 * 8 * 528, /* 1st sector = 32 blocks * 8 pages * 528 bytes */ -+ .mask_flags = MTD_WRITEABLE, /* read-only */ -+ }, -+ { -+ .name = "kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 6 * 32 * 8 * 528, /* 6 sectors */ -+ }, -+ { -+ .name = "filesystem", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL, /* rest = 9 sectors */ -+ } -+}; -+ -+static struct mtd_partition static_partitions_4M[] = -+{ -+ { -+ .name = "bootloader", -+ .offset = 0, -+ .size = 1 * 64 * 8 * 528, /* 1st sector = 64 blocks * 8 pages * 528 bytes */ -+ .mask_flags = MTD_WRITEABLE, /* read-only */ -+ }, -+ { -+ .name = "kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 4 * 64 * 8 * 528, /* 4 sectors */ -+ }, -+ { -+ .name = "filesystem", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL, /* rest = 11 sectors */ -+ } -+}; -+ -+#if defined(CONFIG_MACH_KAFA) -+static struct mtd_partition static_partitions_8M[] = -+{ -+ { -+ name: "romboot", -+ offset: 0, -+ size: 16 * 1056, /* 160 Kb */ -+ mask_flags: MTD_WRITEABLE, /* read-only */ -+ }, -+ { -+ name: "uboot", -+ offset: MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */ -+ size: 128 * 1056, /* 1 MB */ -+ }, -+ { -+ name: "kernel", -+ offset: MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */ -+ size: 1024 * 1056, /* 1 MB */ -+ }, -+ { -+ name: "filesystem", -+ offset: MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */ -+ size: MTDPART_SIZ_FULL, -+ } -+}; -+ -+#elif defined(CONFIG_MACH_MULTMDP) -+ -+static struct mtd_partition static_partitions_8M[] = -+{ -+ { -+ .name = "bootloader", -+ .offset = 0, -+ .size = 12 * 1056, /* 1st sector = 32 blocks * 8 pages * 1056 bytes */ -+ .mask_flags = MTD_WRITEABLE, /* read-only */ -+ }, -+ { -+ .name = "configuration", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 20 * 1056, -+ }, -+ { -+ .name = "kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 1520 * 1056, -+ }, -+ { -+ .name = "filesystem", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL, -+ } -+}; -+ -+#else -+ -+static struct mtd_partition static_partitions_8M[] = -+{ -+ { -+ .name = "bootloader", -+ .offset = 0, -+ .size = 1 * 32 * 8 * 1056, /* 1st sector = 32 blocks * 8 pages * 1056 bytes */ -+ .mask_flags = MTD_WRITEABLE, /* read-only */ -+ }, -+ { -+ .name = "kernel", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = 5 * 32 * 8 * 1056, /* 5 sectors */ -+ }, -+ { -+ .name = "filesystem", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL, /* rest = 26 sectors */ -+ } -+}; -+#endif -+ -+static const char *part_probes[] = { "cmdlinepart", NULL, }; -+ -+#endif -+ -+/* ......................................................................... */ -+ -+/* Allocate a single SPI transfer descriptor. We're assuming that if multiple -+ SPI transfers occur at the same time, spi_access_bus() will serialize them. -+ If this is not valid, then either (i) each dataflash 'priv' structure -+ needs it's own transfer descriptor, (ii) we lock this one, or (iii) use -+ another mechanism. */ -+static struct spi_transfer_list* spi_transfer_desc; -+ -+/* -+ * Perform a SPI transfer to access the DataFlash device. -+ */ -+static int do_spi_transfer(int nr, char* tx, int tx_len, char* rx, int rx_len, -+ char* txnext, int txnext_len, char* rxnext, int rxnext_len) -+{ -+ struct spi_transfer_list* list = spi_transfer_desc; -+ -+ list->tx[0] = tx; list->txlen[0] = tx_len; -+ list->rx[0] = rx; list->rxlen[0] = rx_len; -+ -+ list->tx[1] = txnext; list->txlen[1] = txnext_len; -+ list->rx[1] = rxnext; list->rxlen[1] = rxnext_len; -+ -+ list->nr_transfers = nr; -+ -+ return spi_transfer(list); -+} -+ -+/* ......................................................................... */ -+ -+/* -+ * Poll the DataFlash device until it is READY. -+ */ -+static void at91_dataflash_waitready(void) -+{ -+ char* command = kmalloc(2, GFP_KERNEL); -+ -+ if (!command) -+ return; -+ -+ do { -+ command[0] = OP_READ_STATUS; -+ command[1] = 0; -+ -+ do_spi_transfer(1, command, 2, command, 2, NULL, 0, NULL, 0); -+ } while ((command[1] & 0x80) == 0); -+ -+ kfree(command); -+} -+ -+/* -+ * Return the status of the DataFlash device. -+ */ -+static unsigned short at91_dataflash_status(void) -+{ -+ unsigned short status; -+ char* command = kmalloc(2, GFP_KERNEL); -+ -+ if (!command) -+ return 0; -+ -+ command[0] = OP_READ_STATUS; -+ command[1] = 0; -+ -+ do_spi_transfer(1, command, 2, command, 2, NULL, 0, NULL, 0); -+ status = command[1]; -+ -+ kfree(command); -+ return status; -+} -+ -+/* ......................................................................... */ -+ -+/* -+ * Erase blocks of flash. -+ */ -+static int at91_dataflash_erase(struct mtd_info *mtd, struct erase_info *instr) -+{ -+ struct dataflash_local *priv = (struct dataflash_local *) mtd->priv; -+ unsigned int pageaddr; -+ char* command; -+ -+#ifdef DEBUG_DATAFLASH -+ printk("dataflash_erase: addr=%i len=%i\n", instr->addr, instr->len); -+#endif -+ -+ /* Sanity checks */ -+ if (instr->addr + instr->len > mtd->size) -+ return -EINVAL; -+ if ((instr->len % mtd->erasesize != 0) || (instr->len % priv->page_size != 0)) -+ return -EINVAL; -+ if ((instr->addr % priv->page_size) != 0) -+ return -EINVAL; -+ -+ command = kmalloc(4, GFP_KERNEL); -+ if (!command) -+ return -ENOMEM; -+ -+ while (instr->len > 0) { -+ /* Calculate flash page address */ -+ pageaddr = (instr->addr / priv->page_size) << priv->page_offset; -+ -+ command[0] = OP_ERASE_PAGE; -+ command[1] = (pageaddr & 0x00FF0000) >> 16; -+ command[2] = (pageaddr & 0x0000FF00) >> 8; -+ command[3] = 0; -+#ifdef DEBUG_DATAFLASH -+ printk("ERASE: (%x) %x %x %x [%i]\n", command[0], command[1], command[2], command[3], pageaddr); -+#endif -+ -+ /* Send command to SPI device */ -+ spi_access_bus(priv->spi); -+ do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0); -+ -+ at91_dataflash_waitready(); /* poll status until ready */ -+ spi_release_bus(priv->spi); -+ -+ instr->addr += priv->page_size; /* next page */ -+ instr->len -= priv->page_size; -+ } -+ -+ kfree(command); -+ -+ /* Inform MTD subsystem that erase is complete */ -+ instr->state = MTD_ERASE_DONE; -+ if (instr->callback) -+ instr->callback(instr); -+ -+ return 0; -+} -+ -+/* -+ * Read from the DataFlash device. -+ * from : Start offset in flash device -+ * len : Amount to read -+ * retlen : About of data actually read -+ * buf : Buffer containing the data -+ */ -+static int at91_dataflash_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf) -+{ -+ struct dataflash_local *priv = (struct dataflash_local *) mtd->priv; -+ unsigned int addr; -+ char* command; -+ -+#ifdef DEBUG_DATAFLASH -+ printk("dataflash_read: %lli .. %lli\n", from, from+len); -+#endif -+ -+ *retlen = 0; -+ -+ /* Sanity checks */ -+ if (!len) -+ return 0; -+ if (from + len > mtd->size) -+ return -EINVAL; -+ -+ /* Calculate flash page/byte address */ -+ addr = (((unsigned)from / priv->page_size) << priv->page_offset) + ((unsigned)from % priv->page_size); -+ -+ command = kmalloc(8, GFP_KERNEL); -+ if (!command) -+ return -ENOMEM; -+ -+ command[0] = OP_READ_CONTINUOUS; -+ command[1] = (addr & 0x00FF0000) >> 16; -+ command[2] = (addr & 0x0000FF00) >> 8; -+ command[3] = (addr & 0x000000FF); -+#ifdef DEBUG_DATAFLASH -+ printk("READ: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]); -+#endif -+ -+ /* Send command to SPI device */ -+ spi_access_bus(priv->spi); -+ do_spi_transfer(2, command, 8, command, 8, buf, len, buf, len); -+ spi_release_bus(priv->spi); -+ -+ *retlen = len; -+ kfree(command); -+ return 0; -+} -+ -+/* -+ * Write to the DataFlash device. -+ * to : Start offset in flash device -+ * len : Amount to write -+ * retlen : Amount of data actually written -+ * buf : Buffer containing the data -+ */ -+static int at91_dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u_char *buf) -+{ -+ struct dataflash_local *priv = (struct dataflash_local *) mtd->priv; -+ unsigned int pageaddr, addr, offset, writelen; -+ size_t remaining; -+ u_char *writebuf; -+ unsigned short status; -+ int res = 0; -+ char* command; -+ char* tmpbuf = NULL; -+ -+#ifdef DEBUG_DATAFLASH -+ printk("dataflash_write: %lli .. %lli\n", to, to+len); -+#endif -+ -+ *retlen = 0; -+ -+ /* Sanity checks */ -+ if (!len) -+ return 0; -+ if (to + len > mtd->size) -+ return -EINVAL; -+ -+ command = kmalloc(4, GFP_KERNEL); -+ if (!command) -+ return -ENOMEM; -+ -+ pageaddr = ((unsigned)to / priv->page_size); -+ offset = ((unsigned)to % priv->page_size); -+ if (offset + len > priv->page_size) -+ writelen = priv->page_size - offset; -+ else -+ writelen = len; -+ writebuf = (u_char *)buf; -+ remaining = len; -+ -+ /* Allocate temporary buffer */ -+ tmpbuf = kmalloc(priv->page_size, GFP_KERNEL); -+ if (!tmpbuf) { -+ kfree(command); -+ return -ENOMEM; -+ } -+ -+ /* Gain access to the SPI bus */ -+ spi_access_bus(priv->spi); -+ -+ while (remaining > 0) { -+#ifdef DEBUG_DATAFLASH -+ printk("write @ %i:%i len=%i\n", pageaddr, offset, writelen); -+#endif -+ -+ /* (1) Transfer to Buffer1 */ -+ if (writelen != priv->page_size) { -+ addr = pageaddr << priv->page_offset; -+ command[0] = OP_TRANSFER_BUF1; -+ command[1] = (addr & 0x00FF0000) >> 16; -+ command[2] = (addr & 0x0000FF00) >> 8; -+ command[3] = 0; -+#ifdef DEBUG_DATAFLASH -+ printk("TRANSFER: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]); -+#endif -+ do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0); -+ at91_dataflash_waitready(); -+ } -+ -+ /* (2) Program via Buffer1 */ -+ addr = (pageaddr << priv->page_offset) + offset; -+ command[0] = OP_PROGRAM_VIA_BUF1; -+ command[1] = (addr & 0x00FF0000) >> 16; -+ command[2] = (addr & 0x0000FF00) >> 8; -+ command[3] = (addr & 0x000000FF); -+#ifdef DEBUG_DATAFLASH -+ printk("PROGRAM: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]); -+#endif -+ do_spi_transfer(2, command, 4, command, 4, writebuf, writelen, tmpbuf, writelen); -+ at91_dataflash_waitready(); -+ -+ /* (3) Compare to Buffer1 */ -+ addr = pageaddr << priv->page_offset; -+ command[0] = OP_COMPARE_BUF1; -+ command[1] = (addr & 0x00FF0000) >> 16; -+ command[2] = (addr & 0x0000FF00) >> 8; -+ command[3] = 0; -+#ifdef DEBUG_DATAFLASH -+ printk("COMPARE: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]); -+#endif -+ do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0); -+ at91_dataflash_waitready(); -+ -+ /* Get result of the compare operation */ -+ status = at91_dataflash_status(); -+ if (status & 0x40) { -+ printk("at91_dataflash: Write error on page %i\n", pageaddr); -+ remaining = 0; -+ writelen = 0; -+ res = -EIO; -+ } -+ -+ remaining = remaining - writelen; -+ pageaddr++; -+ offset = 0; -+ writebuf += writelen; -+ *retlen += writelen; -+ -+ if (remaining > priv->page_size) -+ writelen = priv->page_size; -+ else -+ writelen = remaining; -+ } -+ -+ /* Release SPI bus */ -+ spi_release_bus(priv->spi); -+ -+ kfree(tmpbuf); -+ kfree(command); -+ return res; -+} -+ -+/* ......................................................................... */ -+ -+/* -+ * Initialize and register DataFlash device with MTD subsystem. -+ */ -+static int __init add_dataflash(int channel, char *name, int IDsize, -+ int nr_pages, int pagesize, int pageoffset) -+{ -+ struct mtd_info *device; -+ struct dataflash_local *priv; -+#ifdef CONFIG_MTD_PARTITIONS -+ struct mtd_partition *mtd_parts = 0; -+ int mtd_parts_nr = 0; -+#endif -+ -+ if (nr_devices >= DATAFLASH_MAX_DEVICES) { -+ printk(KERN_ERR "at91_dataflash: Too many devices detected\n"); -+ return 0; -+ } -+ -+ device = kmalloc(sizeof(struct mtd_info) + strlen(name) + 8, GFP_KERNEL); -+ if (!device) -+ return -ENOMEM; -+ memset(device, 0, sizeof(struct mtd_info)); -+ -+ device->name = (char *)&device[1]; -+ sprintf(device->name, "%s.spi%d", name, channel); -+ device->size = nr_pages * pagesize; -+ device->erasesize = pagesize; -+ device->writesize = pagesize; -+ device->owner = THIS_MODULE; -+ device->type = MTD_DATAFLASH; -+ device->flags = MTD_WRITEABLE; -+ device->erase = at91_dataflash_erase; -+ device->read = at91_dataflash_read; -+ device->write = at91_dataflash_write; -+ -+ priv = (struct dataflash_local *) kmalloc(sizeof(struct dataflash_local), GFP_KERNEL); -+ if (!priv) { -+ kfree(device); -+ return -ENOMEM; -+ } -+ memset(priv, 0, sizeof(struct dataflash_local)); -+ -+ priv->spi = channel; -+ priv->page_size = pagesize; -+ priv->page_offset = pageoffset; -+ device->priv = priv; -+ -+ mtd_devices[nr_devices] = device; -+ nr_devices++; -+ printk("at91_dataflash: %s detected [spi%i] (%i bytes)\n", name, channel, device->size); -+ -+#ifdef CONFIG_MTD_PARTITIONS -+#ifdef CONFIG_MTD_CMDLINE_PARTS -+ mtd_parts_nr = parse_mtd_partitions(device, part_probes, &mtd_parts, 0); -+#endif -+ if (mtd_parts_nr <= 0) { -+ switch (IDsize) { -+ case SZ_2M: -+ mtd_parts = static_partitions_2M; -+ mtd_parts_nr = ARRAY_SIZE(static_partitions_2M); -+ break; -+ case SZ_4M: -+ mtd_parts = static_partitions_4M; -+ mtd_parts_nr = ARRAY_SIZE(static_partitions_4M); -+ break; -+ case SZ_8M: -+ mtd_parts = static_partitions_8M; -+ mtd_parts_nr = ARRAY_SIZE(static_partitions_8M); -+ break; -+ } -+ } -+ -+ if (mtd_parts_nr > 0) { -+#ifdef CONFIG_DATAFLASH_ALWAYS_ADD_DEVICE -+ add_mtd_device(device); -+#endif -+ return add_mtd_partitions(device, mtd_parts, mtd_parts_nr); -+ } -+#endif -+ return add_mtd_device(device); /* add whole device */ -+} -+ -+/* -+ * Detect and initialize DataFlash device connected to specified SPI channel. -+ * -+ * Device Density ID code Nr Pages Page Size Page offset -+ * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9 -+ * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1025 264 9 -+ * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9 -+ * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9 -+ * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10 -+ * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10 -+ * AT45DB0642 64Mbit (8M) xx1111xx (0x3c) 8192 1056 11 -+ * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11 -+ */ -+static int __init at91_dataflash_detect(int channel) -+{ -+ int res = 0; -+ unsigned short status; -+ -+ spi_access_bus(channel); -+ status = at91_dataflash_status(); -+ spi_release_bus(channel); -+ if (status != 0xff) { /* no dataflash device there */ -+ switch (status & 0x3c) { -+ case 0x0c: /* 0 0 1 1 */ -+ res = add_dataflash(channel, "AT45DB011B", SZ_128K, 512, 264, 9); -+ break; -+ case 0x14: /* 0 1 0 1 */ -+ res = add_dataflash(channel, "AT45DB021B", SZ_256K, 1025, 264, 9); -+ break; -+ case 0x1c: /* 0 1 1 1 */ -+ res = add_dataflash(channel, "AT45DB041B", SZ_512K, 2048, 264, 9); -+ break; -+ case 0x24: /* 1 0 0 1 */ -+ res = add_dataflash(channel, "AT45DB081B", SZ_1M, 4096, 264, 9); -+ break; -+ case 0x2c: /* 1 0 1 1 */ -+ res = add_dataflash(channel, "AT45DB161B", SZ_2M, 4096, 528, 10); -+ break; -+ case 0x34: /* 1 1 0 1 */ -+ res = add_dataflash(channel, "AT45DB321B", SZ_4M, 8192, 528, 10); -+ break; -+ case 0x3c: /* 1 1 1 1 */ -+ res = add_dataflash(channel, "AT45DB642", SZ_8M, 8192, 1056, 11); -+ break; -+// Currently unsupported since Atmel removed the "Main Memory Program via Buffer" commands. -+// case 0x10: /* 0 1 0 0 */ -+// res = add_dataflash(channel, "AT45DB1282", SZ_16M, 16384, 1056, 11); -+// break; -+ default: -+ printk(KERN_ERR "at91_dataflash: Unknown device (%x)\n", status & 0x3c); -+ } -+ } -+ -+ return res; -+} -+ -+static int __init at91_dataflash_init(void) -+{ -+ spi_transfer_desc = kmalloc(sizeof(struct spi_transfer_list), GFP_KERNEL); -+ if (!spi_transfer_desc) -+ return -ENOMEM; -+ -+ /* DataFlash (SPI chip select 0) */ -+ at91_dataflash_detect(0); -+ -+ if (machine_is_sweda_tms()) -+ at91_dataflash_detect(1); /* DataFlash device (SPI chip select 1) */ -+ -+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD -+ /* DataFlash card (SPI chip select 3) */ -+ at91_dataflash_detect(3); -+#endif -+ -+ return 0; -+} -+ -+static void __exit at91_dataflash_exit(void) -+{ -+ int i; -+ -+ for (i = 0; i < DATAFLASH_MAX_DEVICES; i++) { -+ if (mtd_devices[i]) { -+#ifdef CONFIG_MTD_PARTITIONS -+ del_mtd_partitions(mtd_devices[i]); -+#else -+ del_mtd_device(mtd_devices[i]); -+#endif -+ kfree(mtd_devices[i]->priv); -+ kfree(mtd_devices[i]); -+ } -+ } -+ nr_devices = 0; -+ kfree(spi_transfer_desc); -+} -+ -+ -+module_init(at91_dataflash_init); -+module_exit(at91_dataflash_exit); -+ -+MODULE_LICENSE("GPL"); -+MODULE_AUTHOR("Andrew Victor"); -+MODULE_DESCRIPTION("DataFlash driver for Atmel AT91RM9200"); ---- a/drivers/mtd/nand/Kconfig -+++ b/drivers/mtd/nand/Kconfig -@@ -273,12 +273,53 @@ config MTD_NAND_CS553X - If you say "m", the module will be called "cs553x_nand.ko". - - config MTD_NAND_AT91 -- bool "Support for NAND Flash / SmartMedia on AT91" -+ tristate "Support for NAND Flash / SmartMedia on AT91" - depends on ARCH_AT91 - help - Enables support for NAND Flash / Smart Media Card interface - on Atmel AT91 processors. - -+choice -+ prompt "ECC management for NAND Flash / SmartMedia on AT91" -+ depends on MTD_NAND_AT91 -+ -+config MTD_NAND_AT91_ECC_SOFT -+ bool "Software ECC" -+ depends on MTD_NAND_AT91 -+ help -+ Uses software ECC. -+ -+ NB : hardware and software ECC schemes are incompatible. -+ If you switch from one to another, you'll have to erase your -+ mtd partition. -+ -+config MTD_NAND_AT91_ECC_HW -+ bool "Hardware ECC" -+ depends on MTD_NAND_AT91 && (ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9) -+ help -+ Uses hardware ECC provided by the AT91 processor -+ instead of software ECC. -+ The hardware ECC controller is capable of single bit error -+ correction and 2-bit random detection per page. -+ -+ NB : hardware and software ECC schemes are incompatible. -+ If you switch from one to another, you'll have to erase your -+ mtd partition. -+ -+ If unsure, say Y -+ -+config MTD_NAND_AT91_ECC_NONE -+ bool "No ECC (Testing Only)" -+ depends on MTD_NAND_AT91 -+ help -+ No ECC will be used. -+ It's not a good idea and it should be reserved for testing -+ purpose only. -+ -+ If unsure, say N -+ -+endchoice -+ - config MTD_NAND_CM_X270 - tristate "Support for NAND Flash on CM-X270 modules" - depends on MTD_NAND && MACH_ARMCORE ---- a/drivers/mtd/nand/at91_nand.c -+++ b/drivers/mtd/nand/at91_nand.c -@@ -9,6 +9,15 @@ - * Derived from drivers/mtd/spia.c - * Copyright (C) 2000 Steven J. Hill (sjhill@cotw.com) - * -+ * -+ * Add Hardware ECC support for AT91SAM9260 / AT91SAM9263 -+ * Richard Genoud (richard.genoud@gmail.com), Adeneo Copyright (C) 2007 -+ * -+ * Derived from Das U-Boot source code -+ * (u-boot-1.1.5/board/atmel/at91sam9263ek/nand.c) -+ * (C) Copyright 2006 ATMEL Rousset, Lacressonniere Nicolas -+ * -+ * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -@@ -28,15 +37,75 @@ - #include <asm/hardware.h> - #include <asm/arch/board.h> - #include <asm/arch/gpio.h> -+#include <asm/arch/at91_ecc.h> -+ -+#ifdef CONFIG_MTD_NAND_AT91_ECC_HW -+#define hard_ecc 1 -+#else -+#define hard_ecc 0 -+#endif -+ -+#ifdef CONFIG_MTD_NAND_AT91_ECC_NONE -+#define no_ecc 1 -+#else -+#define no_ecc 0 -+#endif -+ -+/* Register access macros */ -+#define ecc_readl(base, reg) __raw_readl(base + reg) -+#define ecc_writel(base, reg, value) __raw_writel((value), base + reg) -+ -+ -+/* -+ * OOB layout for large page size. -+ * bad block info is on bytes 0 and 1 -+ * the bytes must be consecutives to avoid several NAND_CMD_RNDOUT during read. -+ */ -+static struct nand_ecclayout at91_oobinfo_large = { -+ .eccbytes = 4, -+ .eccpos = {60, 61, 62, 63}, -+ .oobfree = { {2, 58} }, -+}; -+ -+/* -+ * OOB layout for small page size -+ * bad block info is on bytes 4 and 5 -+ * the bytes must be consecutives to avoid several NAND_CMD_RNDOUT during read. -+ */ -+static struct nand_ecclayout at91_oobinfo_small = { -+ .eccbytes = 4, -+ .eccpos = {0, 1, 2, 3}, -+ .oobfree = { {6, 10} }, -+}; - - struct at91_nand_host { - struct nand_chip nand_chip; - struct mtd_info mtd; - void __iomem *io_base; - struct at91_nand_data *board; -+ struct device *dev; -+ void __iomem *ecc; - }; - - /* -+ * Enable NAND chip-select. -+ */ -+static void at91_nand_enable(struct at91_nand_host *host) -+{ -+ if (host->board->enable_pin) -+ at91_set_gpio_value(host->board->enable_pin, 0); -+} -+ -+/* -+ * Disable NAND chip-select. -+ */ -+static void at91_nand_disable(struct at91_nand_host *host) -+{ -+ if (host->board->enable_pin) -+ at91_set_gpio_value(host->board->enable_pin, 1); -+} -+ -+/* - * Hardware specific access to control-lines - */ - static void at91_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) -@@ -44,6 +113,13 @@ static void at91_nand_cmd_ctrl(struct mt - struct nand_chip *nand_chip = mtd->priv; - struct at91_nand_host *host = nand_chip->priv; - -+ if (ctrl & NAND_CTRL_CHANGE) { -+ if (ctrl & NAND_NCE) -+ at91_nand_enable(host); -+ else -+ at91_nand_disable(host); -+ } -+ - if (cmd == NAND_CMD_NONE) - return; - -@@ -65,27 +141,249 @@ static int at91_nand_device_ready(struct - } - - /* -- * Enable NAND. -+ * write oob for small pages - */ --static void at91_nand_enable(struct at91_nand_host *host) -+static int at91_nand_write_oob_512(struct mtd_info *mtd, -+ struct nand_chip *chip, int page) - { -- if (host->board->enable_pin) -- at91_set_gpio_value(host->board->enable_pin, 0); -+ int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; -+ int eccsize = chip->ecc.size, length = mtd->oobsize; -+ int len, pos, status = 0; -+ const uint8_t *bufpoi = chip->oob_poi; -+ -+ pos = eccsize + chunk; -+ -+ chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page); -+ len = min_t(int, length, chunk); -+ chip->write_buf(mtd, bufpoi, len); -+ bufpoi += len; -+ length -= len; -+ if (length > 0) -+ chip->write_buf(mtd, bufpoi, length); -+ -+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); -+ status = chip->waitfunc(mtd, chip); -+ -+ return status & NAND_STATUS_FAIL ? -EIO : 0; -+ - } - - /* -- * Disable NAND. -+ * read oob for small pages - */ --static void at91_nand_disable(struct at91_nand_host *host) -+static int at91_nand_read_oob_512(struct mtd_info *mtd, -+ struct nand_chip *chip, int page, int sndcmd) - { -- if (host->board->enable_pin) -- at91_set_gpio_value(host->board->enable_pin, 1); -+ if (sndcmd) { -+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); -+ sndcmd = 0; -+ } -+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); -+ return sndcmd; -+} -+ -+/* -+ * Calculate HW ECC -+ * -+ * mtd: MTD block structure -+ * dat: raw data (unused) -+ * ecc_code: buffer for ECC -+ */ -+static int at91_nand_calculate(struct mtd_info *mtd, -+ const u_char *dat, unsigned char *ecc_code) -+{ -+ struct nand_chip *nand_chip = mtd->priv; -+ struct at91_nand_host *host = nand_chip->priv; -+ uint32_t *eccpos = nand_chip->ecc.layout->eccpos; -+ unsigned int ecc_value; -+ -+ /* get the first 2 ECC bytes */ -+ ecc_value = ecc_readl(host->ecc, AT91_ECC_PR) & (AT91_ECC_BITADDR | AT91_ECC_WORDADDR); -+ -+ ecc_code[eccpos[0]] = ecc_value & 0xFF; -+ ecc_code[eccpos[1]] = (ecc_value >> 8) & 0xFF; -+ -+ /* get the last 2 ECC bytes */ -+ ecc_value = ecc_readl(host->ecc, AT91_ECC_NPR) & AT91_ECC_NPARITY; -+ -+ ecc_code[eccpos[2]] = ecc_value & 0xFF; -+ ecc_code[eccpos[3]] = (ecc_value >> 8) & 0xFF; -+ -+ return 0; - } - -+/* -+ * HW ECC read page function -+ * -+ * mtd: mtd info structure -+ * chip: nand chip info structure -+ * buf: buffer to store read data -+ */ -+static int at91_nand_read_page(struct mtd_info *mtd, -+ struct nand_chip *chip, uint8_t *buf) -+{ -+ int eccsize = chip->ecc.size; -+ int eccbytes = chip->ecc.bytes; -+ uint32_t *eccpos = chip->ecc.layout->eccpos; -+ uint8_t *p = buf; -+ uint8_t *oob = chip->oob_poi; -+ uint8_t *ecc_pos; -+ int stat; -+ -+ /* read the page */ -+ chip->read_buf(mtd, p, eccsize); -+ -+ /* move to ECC position if needed */ -+ if (eccpos[0] != 0) { -+ /* -+ * This only works on large pages because the ECC controller -+ * waits for NAND_CMD_RNDOUTSTART after the NAND_CMD_RNDOUT. -+ * Anyway, for small pages, the eccpos[0] == 0 -+ */ -+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, -+ mtd->writesize + eccpos[0], -1); -+ } -+ -+ /* the ECC controller needs to read the ECC just after the data */ -+ ecc_pos = oob + eccpos[0]; -+ chip->read_buf(mtd, ecc_pos, eccbytes); -+ -+ /* check if there's an error */ -+ stat = chip->ecc.correct(mtd, p, oob, NULL); -+ -+ if (stat < 0) -+ mtd->ecc_stats.failed++; -+ else -+ mtd->ecc_stats.corrected += stat; -+ -+ /* get back to oob start (end of page) */ -+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1); -+ -+ /* read the oob */ -+ chip->read_buf(mtd, oob, mtd->oobsize); -+ -+ return 0; -+} -+ -+/* -+ * HW ECC Correction -+ * -+ * mtd: MTD block structure -+ * dat: raw data read from the chip -+ * read_ecc: ECC from the chip (unused) -+ * isnull: unused -+ * -+ * Detect and correct a 1 bit error for a page -+ */ -+static int at91_nand_correct(struct mtd_info *mtd, u_char *dat, -+ u_char *read_ecc, u_char *isnull) -+{ -+ struct nand_chip *nand_chip = mtd->priv; -+ struct at91_nand_host *host = nand_chip->priv; -+ unsigned int ecc_status; -+ unsigned int ecc_word, ecc_bit; -+ -+ /* get the status from the Status Register */ -+ ecc_status = ecc_readl(host->ecc, AT91_ECC_SR); -+ -+ /* if there's no error */ -+ if (likely(!(ecc_status & AT91_ECC_RECERR))) -+ return 0; -+ -+ /* get error bit offset (4 bits) */ -+ ecc_bit = ecc_readl(host->ecc, AT91_ECC_PR) & AT91_ECC_BITADDR; -+ /* get word address (12 bits) */ -+ ecc_word = ecc_readl(host->ecc, AT91_ECC_PR) & AT91_ECC_WORDADDR; -+ ecc_word >>= 4; -+ -+ /* if there are multiple errors */ -+ if (ecc_status & AT91_ECC_MULERR) { -+ /* Check if it is a freshly erased block (filled with 0xff) */ -+ if ((ecc_bit == AT91_ECC_BITADDR) -+ && (ecc_word == (AT91_ECC_WORDADDR >> 4))) { -+ /* the block has just been erased, return OK */ -+ return 0; -+ } -+ /* -+ * It doesn't seems to be a freshly-erased block. -+ * We can't correct so many errors. -+ */ -+ dev_dbg(host->dev, "at91_nand : multiple errors detected." -+ " Unable to correct.\n"); -+ return -EIO; -+ } -+ -+ /* if there's a single bit error : we can correct it */ -+ if (ecc_status & AT91_ECC_ECCERR) { -+ /* -+ * There's nothing much to do here. -+ * The bit error is on the ECC itself. -+ */ -+ dev_dbg(host->dev, "at91_nand : one bit error on ECC code." -+ " Nothing to correct\n"); -+ return 0; -+ } -+ -+ dev_dbg(host->dev, "at91_nand : one bit error on data." -+ " (word offset in the page :" -+ " 0x%x bit offset : 0x%x)\n", -+ ecc_word, ecc_bit); -+ /* correct the error */ -+ if (nand_chip->options & NAND_BUSWIDTH_16) { -+ /* 16 bits words */ -+ ((unsigned short *) dat)[ecc_word] ^= (1 << ecc_bit); -+ } else { -+ /* 8 bits words */ -+ dat[ecc_word] ^= (1 << ecc_bit); -+ } -+ dev_dbg(host->dev, "at91_nand : error corrected\n"); -+ return 1; -+} -+ -+/* -+ * Enable HW ECC : unsused -+ */ -+static void at91_nand_hwctl(struct mtd_info *mtd, int mode) { ; } -+ -+/* -+ * Over-ride the standard functions with our optimized versions. -+ * We can use read/write blocks to move data to/from the controller. -+ */ -+static void at91_read_buf8(struct mtd_info *mtd, u8 *buf, int len) -+{ -+ struct nand_chip *nand_chip = mtd->priv; -+ -+ __raw_readsb(nand_chip->IO_ADDR_R, buf, len); -+} -+ -+static void at91_read_buf16(struct mtd_info *mtd, u8 *buf, int len) -+{ -+ struct nand_chip *nand_chip = mtd->priv; -+ -+ __raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2); -+} -+ -+static void at91_write_buf8(struct mtd_info *mtd, const u8 *buf, int len) -+{ -+ struct nand_chip *nand_chip = mtd->priv; -+ -+ __raw_writesb(nand_chip->IO_ADDR_W, buf, len); -+} -+ -+static void at91_write_buf16(struct mtd_info *mtd, const u8 *buf, int len) -+{ -+ struct nand_chip *nand_chip = mtd->priv; -+ -+ __raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2); -+} -+ -+ - #ifdef CONFIG_MTD_PARTITIONS --const char *part_probes[] = { "cmdlinepart", NULL }; -+static const char *part_probes[] = { "cmdlinepart", NULL }; - #endif - -+static char* ecc_modes[] __initdata = { "No", "Software", "Hardware" }; -+ - /* - * Probe for the NAND device. - */ -@@ -94,6 +392,8 @@ static int __init at91_nand_probe(struct - struct at91_nand_host *host; - struct mtd_info *mtd; - struct nand_chip *nand_chip; -+ struct resource *regs; -+ struct resource *mem; - int res; - - #ifdef CONFIG_MTD_PARTITIONS -@@ -108,8 +408,13 @@ static int __init at91_nand_probe(struct - return -ENOMEM; - } - -- host->io_base = ioremap(pdev->resource[0].start, -- pdev->resource[0].end - pdev->resource[0].start + 1); -+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ if (!mem) { -+ printk(KERN_ERR "at91_nand: can't get I/O resource mem\n"); -+ return -ENXIO; -+ } -+ -+ host->io_base = ioremap(mem->start, mem->end - mem->start + 1); - if (host->io_base == NULL) { - printk(KERN_ERR "at91_nand: ioremap failed\n"); - kfree(host); -@@ -119,6 +424,7 @@ static int __init at91_nand_probe(struct - mtd = &host->mtd; - nand_chip = &host->nand_chip; - host->board = pdev->dev.platform_data; -+ host->dev = &pdev->dev; - - nand_chip->priv = host; /* link the private data structures */ - mtd->priv = nand_chip; -@@ -132,11 +438,40 @@ static int __init at91_nand_probe(struct - if (host->board->rdy_pin) - nand_chip->dev_ready = at91_nand_device_ready; - -+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 1); -+ if (!regs && hard_ecc) { -+ printk(KERN_ERR "at91_nand: can't get I/O resource " -+ "regs\nFalling back on software ECC\n"); -+ } -+ - nand_chip->ecc.mode = NAND_ECC_SOFT; /* enable ECC */ -+ if (no_ecc) -+ nand_chip->ecc.mode = NAND_ECC_NONE; -+ if (hard_ecc && regs) { -+ host->ecc = (void __force __iomem *) (AT91_VA_BASE_SYS - AT91_BASE_SYS); -+ host->ecc += regs->start; -+ -+ nand_chip->ecc.mode = NAND_ECC_HW_SYNDROME; /* HW SYNDROME ECC */ -+ nand_chip->ecc.calculate = at91_nand_calculate; /* function called after a write */ -+ nand_chip->ecc.correct = at91_nand_correct; /* function called after a read */ -+ nand_chip->ecc.hwctl = at91_nand_hwctl; /* unused */ -+ nand_chip->ecc.read_page = at91_nand_read_page; /* read page function */ -+ nand_chip->ecc.bytes = 4; /* 4 ECC bytes for any page size */ -+ nand_chip->ecc.prepad = 0; -+ nand_chip->ecc.postpad = 0; -+ } -+ - nand_chip->chip_delay = 20; /* 20us command delay time */ - -- if (host->board->bus_width_16) /* 16-bit bus width */ -+ if (host->board->bus_width_16) { /* 16-bit bus width */ - nand_chip->options |= NAND_BUSWIDTH_16; -+ nand_chip->read_buf = at91_read_buf16; -+ nand_chip->write_buf = at91_write_buf16; -+ } -+ else { -+ nand_chip->read_buf = at91_read_buf8; -+ nand_chip->write_buf = at91_write_buf8; -+ } - - platform_set_drvdata(pdev, host); - at91_nand_enable(host); -@@ -149,8 +484,60 @@ static int __init at91_nand_probe(struct - } - } - -- /* Scan to find existance of the device */ -- if (nand_scan(mtd, 1)) { -+ /* first scan to find the device and get the page size */ -+ if (nand_scan_ident(mtd, 1)) { -+ res = -ENXIO; -+ goto out; -+ } -+ -+ if (nand_chip->ecc.mode == NAND_ECC_HW_SYNDROME) { -+ /* ECC is calculated for the whole page (1 step) */ -+ nand_chip->ecc.size = mtd->writesize; -+ -+ /* set ECC page size and oob layout */ -+ switch (mtd->writesize) { -+ case 512: -+ nand_chip->ecc.layout = &at91_oobinfo_small; -+ nand_chip->ecc.read_oob = at91_nand_read_oob_512; -+ nand_chip->ecc.write_oob = at91_nand_write_oob_512; -+ ecc_writel(host->ecc, AT91_ECC_MR, AT91_ECC_PAGESIZE_528); -+ break; -+ case 1024: -+ nand_chip->ecc.layout = &at91_oobinfo_large; -+ ecc_writel(host->ecc, AT91_ECC_MR, AT91_ECC_PAGESIZE_1056); -+ break; -+ case 2048: -+ nand_chip->ecc.layout = &at91_oobinfo_large; -+ ecc_writel(host->ecc, AT91_ECC_MR, AT91_ECC_PAGESIZE_2112); -+ break; -+ case 4096: -+ nand_chip->ecc.layout = &at91_oobinfo_large; -+ ecc_writel(host->ecc, AT91_ECC_MR, AT91_ECC_PAGESIZE_4224); -+ break; -+ default: -+ /* -+ * Page size not supported by HW ECC. -+ * So switch back to soft ECC -+ */ -+ nand_chip->ecc.mode = NAND_ECC_SOFT; -+ nand_chip->ecc.calculate = NULL; -+ nand_chip->ecc.correct = NULL; -+ nand_chip->ecc.hwctl = NULL; -+ nand_chip->ecc.read_page = NULL; -+ nand_chip->ecc.postpad = 0; -+ nand_chip->ecc.prepad = 0; -+ nand_chip->ecc.bytes = 0; -+ break; -+ } -+ } -+ -+ printk(KERN_INFO "AT91 NAND: %i-bit, %s ECC\n", -+ (nand_chip->options & NAND_BUSWIDTH_16) ? 16 : 8, -+ ecc_modes[nand_chip->ecc.mode] -+ ); -+ -+ /* second phase scan */ -+ if (nand_scan_tail(mtd)) { - res = -ENXIO; - goto out; - } -@@ -179,8 +566,11 @@ static int __init at91_nand_probe(struct - if (!res) - return res; - -+#ifdef CONFIG_MTD_PARTITIONS - release: -+#endif - nand_release(mtd); -+ - out: - at91_nand_disable(host); - platform_set_drvdata(pdev, NULL); -@@ -192,7 +582,7 @@ out: - /* - * Remove a NAND device. - */ --static int __devexit at91_nand_remove(struct platform_device *pdev) -+static int __exit at91_nand_remove(struct platform_device *pdev) - { - struct at91_nand_host *host = platform_get_drvdata(pdev); - struct mtd_info *mtd = &host->mtd; -@@ -208,8 +598,7 @@ static int __devexit at91_nand_remove(st - } - - static struct platform_driver at91_nand_driver = { -- .probe = at91_nand_probe, -- .remove = at91_nand_remove, -+ .remove = __exit_p(at91_nand_remove), - .driver = { - .name = "at91_nand", - .owner = THIS_MODULE, -@@ -218,7 +607,7 @@ static struct platform_driver at91_nand_ - - static int __init at91_nand_init(void) - { -- return platform_driver_register(&at91_nand_driver); -+ return platform_driver_probe(&at91_nand_driver, at91_nand_probe); - } - - -@@ -233,4 +622,4 @@ module_exit(at91_nand_exit); - - MODULE_LICENSE("GPL"); - MODULE_AUTHOR("Rick Bronson"); --MODULE_DESCRIPTION("NAND/SmartMedia driver for AT91RM9200"); -+MODULE_DESCRIPTION("NAND/SmartMedia driver for AT91RM9200 / AT91SAM9 / AT91CAP9"); ---- a/drivers/net/arm/Kconfig -+++ b/drivers/net/arm/Kconfig -@@ -47,3 +47,10 @@ config EP93XX_ETH - help - This is a driver for the ethernet hardware included in EP93xx CPUs. - Say Y if you are building a kernel for EP93xx based devices. -+ -+config ARM_KS8695_ETHER -+ tristate "KS8695 Ethernet support" -+ depends on NET_ETHERNET && ARM && ARCH_KS8695 -+ help -+ If you wish to compile a kernel for an KS8695-based board -+ and enable Ethernet support, then select this option. ---- a/drivers/net/arm/Makefile -+++ b/drivers/net/arm/Makefile -@@ -9,3 +9,4 @@ obj-$(CONFIG_ARM_ETHER3) += ether3.o - obj-$(CONFIG_ARM_ETHER1) += ether1.o - obj-$(CONFIG_ARM_AT91_ETHER) += at91_ether.o - obj-$(CONFIG_EP93XX_ETH) += ep93xx_eth.o -+obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695_ether.o ---- a/drivers/net/arm/at91_ether.c -+++ b/drivers/net/arm/at91_ether.c -@@ -220,7 +220,7 @@ static irqreturn_t at91ether_phy_interru - if (!(phy & (1 << 0))) - goto done; - } -- else if (lp->phy_type == MII_KS8721_ID) { -+ else if ((lp->phy_type == MII_KS8721_ID) || (lp->phy_type == MII_KSZ8041_ID)) { - read_phy(lp->phy_address, MII_TPISTATUS, &phy); /* ack interrupt in Micrel PHY */ - if (!(phy & ((1 << 2) | 1))) - goto done; -@@ -286,7 +286,7 @@ static void enable_phyirq(struct net_dev - dsintr = (1 << 15) | ( 1 << 14); - write_phy(lp->phy_address, MII_BCMINTR_REG, dsintr); - } -- else if (lp->phy_type == MII_KS8721_ID) { /* for Micrel PHY */ -+ else if ((lp->phy_type == MII_KS8721_ID) || (lp->phy_type == MII_KSZ8041_ID)) { /* for Micrel PHY */ - dsintr = (1 << 10) | ( 1 << 8); - write_phy(lp->phy_address, MII_TPISTATUS, dsintr); - } -@@ -341,7 +341,7 @@ static void disable_phyirq(struct net_de - dsintr = ~(1 << 14); - write_phy(lp->phy_address, MII_BCMINTR_REG, dsintr); - } -- else if (lp->phy_type == MII_KS8721_ID) { /* for Micrel PHY */ -+ else if ((lp->phy_type == MII_KS8721_ID) || (lp->phy_type == MII_KSZ8041_ID)) { /* for Micrel PHY */ - read_phy(lp->phy_address, MII_TPISTATUS, &dsintr); - dsintr = ~((1 << 10) | (1 << 8)); - write_phy(lp->phy_address, MII_TPISTATUS, dsintr); -@@ -820,7 +820,7 @@ static int at91ether_tx(struct sk_buff * - lp->skb = skb; - lp->skb_length = skb->len; - lp->skb_physaddr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE); -- lp->stats.tx_bytes += skb->len; -+ dev->stats.tx_bytes += skb->len; - - /* Set address of the data in the Transmit Address register */ - at91_emac_write(AT91_EMAC_TAR, lp->skb_physaddr); -@@ -843,34 +843,32 @@ static int at91ether_tx(struct sk_buff * - */ - static struct net_device_stats *at91ether_stats(struct net_device *dev) - { -- struct at91_private *lp = netdev_priv(dev); -- int ale, lenerr, seqe, lcol, ecol; -+ int ale, lenerr, seqe, ecol; - - if (netif_running(dev)) { -- lp->stats.rx_packets += at91_emac_read(AT91_EMAC_OK); /* Good frames received */ -+ dev->stats.rx_packets += at91_emac_read(AT91_EMAC_OK); /* Good frames received */ - ale = at91_emac_read(AT91_EMAC_ALE); -- lp->stats.rx_frame_errors += ale; /* Alignment errors */ -+ dev->stats.rx_frame_errors += ale; /* Alignment errors */ - lenerr = at91_emac_read(AT91_EMAC_ELR) + at91_emac_read(AT91_EMAC_USF); -- lp->stats.rx_length_errors += lenerr; /* Excessive Length or Undersize Frame error */ -+ dev->stats.rx_length_errors += lenerr; /* Excessive Length or Undersize Frame error */ - seqe = at91_emac_read(AT91_EMAC_SEQE); -- lp->stats.rx_crc_errors += seqe; /* CRC error */ -- lp->stats.rx_fifo_errors += at91_emac_read(AT91_EMAC_DRFC); /* Receive buffer not available */ -- lp->stats.rx_errors += (ale + lenerr + seqe -+ dev->stats.rx_crc_errors += seqe; /* CRC error */ -+ dev->stats.rx_fifo_errors += at91_emac_read(AT91_EMAC_DRFC); /* Receive buffer not available */ -+ dev->stats.rx_errors += (ale + lenerr + seqe - + at91_emac_read(AT91_EMAC_CDE) + at91_emac_read(AT91_EMAC_RJB)); - -- lp->stats.tx_packets += at91_emac_read(AT91_EMAC_FRA); /* Frames successfully transmitted */ -- lp->stats.tx_fifo_errors += at91_emac_read(AT91_EMAC_TUE); /* Transmit FIFO underruns */ -- lp->stats.tx_carrier_errors += at91_emac_read(AT91_EMAC_CSE); /* Carrier Sense errors */ -- lp->stats.tx_heartbeat_errors += at91_emac_read(AT91_EMAC_SQEE);/* Heartbeat error */ -+ dev->stats.tx_packets += at91_emac_read(AT91_EMAC_FRA); /* Frames successfully transmitted */ -+ dev->stats.tx_fifo_errors += at91_emac_read(AT91_EMAC_TUE); /* Transmit FIFO underruns */ -+ dev->stats.tx_carrier_errors += at91_emac_read(AT91_EMAC_CSE); /* Carrier Sense errors */ -+ dev->stats.tx_heartbeat_errors += at91_emac_read(AT91_EMAC_SQEE);/* Heartbeat error */ - -- lcol = at91_emac_read(AT91_EMAC_LCOL); -+ dev->stats.tx_window_errors += at91_emac_read(AT91_EMAC_LCOL); /* Late collisions */ - ecol = at91_emac_read(AT91_EMAC_ECOL); -- lp->stats.tx_window_errors += lcol; /* Late collisions */ -- lp->stats.tx_aborted_errors += ecol; /* 16 collisions */ -+ dev->stats.tx_aborted_errors += ecol; /* 16 collisions */ - -- lp->stats.collisions += (at91_emac_read(AT91_EMAC_SCOL) + at91_emac_read(AT91_EMAC_MCOL) + lcol + ecol); -+ dev->stats.collisions += (at91_emac_read(AT91_EMAC_SCOL) + at91_emac_read(AT91_EMAC_MCOL) + ecol); - } -- return &lp->stats; -+ return &dev->stats; - } - - /* -@@ -896,16 +894,16 @@ static void at91ether_rx(struct net_devi - - skb->protocol = eth_type_trans(skb, dev); - dev->last_rx = jiffies; -- lp->stats.rx_bytes += pktlen; -+ dev->stats.rx_bytes += pktlen; - netif_rx(skb); - } - else { -- lp->stats.rx_dropped += 1; -+ dev->stats.rx_dropped += 1; - printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", dev->name); - } - - if (dlist->descriptors[lp->rxBuffIndex].size & EMAC_MULTICAST) -- lp->stats.multicast++; -+ dev->stats.multicast++; - - dlist->descriptors[lp->rxBuffIndex].addr &= ~EMAC_DESC_DONE; /* reset ownership bit */ - if (lp->rxBuffIndex == MAX_RX_DESCR-1) /* wrap after last buffer */ -@@ -934,7 +932,7 @@ static irqreturn_t at91ether_interrupt(i - if (intstatus & AT91_EMAC_TCOM) { /* Transmit complete */ - /* The TCOM bit is set even if the transmission failed. */ - if (intstatus & (AT91_EMAC_TUND | AT91_EMAC_RTRY)) -- lp->stats.tx_errors += 1; -+ dev->stats.tx_errors += 1; - - if (lp->skb) { - dev_kfree_skb_irq(lp->skb); -@@ -978,15 +976,22 @@ static int __init at91ether_setup(unsign - struct net_device *dev; - struct at91_private *lp; - unsigned int val; -- int res; -+ struct resource *res; -+ int ret; - DECLARE_MAC_BUF(mac); - - dev = alloc_etherdev(sizeof(struct at91_private)); - if (!dev) - return -ENOMEM; - -- dev->base_addr = AT91_VA_BASE_EMAC; -- dev->irq = AT91RM9200_ID_EMAC; -+ /* Get I/O base address and IRQ */ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ if (!res) { -+ free_netdev(dev); -+ return -ENODEV; -+ } -+ dev->base_addr = res->start; -+ dev->irq = platform_get_irq(pdev, 0); - - /* Install the interrupt handler */ - if (request_irq(dev->irq, at91ether_interrupt, 0, dev->name, dev)) { -@@ -1043,7 +1048,9 @@ static int __init at91ether_setup(unsign - } else if (machine_is_csb337()) { - /* mix link activity status into LED2 link state */ - write_phy(phy_address, MII_LEDCTRL_REG, 0x0d22); -- } -+ } else if (machine_is_ecbat91()) -+ write_phy(phy_address, MII_LEDCTRL_REG, 0x156A); -+ - disable_mdi(); - spin_unlock_irq(&lp->lock); - -@@ -1058,12 +1065,12 @@ static int __init at91ether_setup(unsign - lp->phy_address = phy_address; /* MDI address of PHY */ - - /* Register the network interface */ -- res = register_netdev(dev); -- if (res) { -+ ret = register_netdev(dev); -+ if (ret) { - free_irq(dev->irq, dev); - free_netdev(dev); - dma_free_coherent(NULL, sizeof(struct recv_desc_bufs), lp->dlist, (dma_addr_t)lp->dlist_phys); -- return res; -+ return ret; - } - - /* Determine current link speed */ -@@ -1101,6 +1108,8 @@ static int __init at91ether_setup(unsign - printk(KERN_INFO "%s: National Semiconductor DP83848 PHY\n", dev->name); - else if (phy_type == MII_AC101L_ID) - printk(KERN_INFO "%s: Altima AC101L PHY\n", dev->name); -+ else if (phy_type == MII_KSZ8041_ID) -+ printk(KERN_INFO "%s: Micrel KSZ8041 PHY\n", dev->name); - else if (phy_type == MII_KS8721_ID) - printk(KERN_INFO "%s: Micrel KS8721 PHY\n", dev->name); - else if (phy_type == MII_T78Q21x3_ID) -@@ -1146,6 +1155,7 @@ static int __init at91ether_probe(struct - case MII_DP83847_ID: /* National Semiconductor DP83847: */ - case MII_DP83848_ID: /* National Semiconductor DP83848: */ - case MII_AC101L_ID: /* Altima AC101L: PHY_ID1 = 0x22, PHY_ID2 = 0x5520 */ -+ case MII_KSZ8041_ID: /* Micrel KSZ8041: PHY_ID1 = 0x22, PHY_ID2 = 0x1512 */ - case MII_KS8721_ID: /* Micrel KS8721: PHY_ID1 = 0x22, PHY_ID2 = 0x1610 */ - case MII_T78Q21x3_ID: /* Teridian 78Q21x3: PHY_ID1 = 0x0E, PHY_ID2 = 7237 */ - case MII_LAN83C185_ID: /* SMSC LAN83C185: PHY_ID1 = 0x0007, PHY_ID2 = 0xC0A1 */ -@@ -1246,3 +1256,4 @@ module_exit(at91ether_exit) - MODULE_LICENSE("GPL"); - MODULE_DESCRIPTION("AT91RM9200 EMAC Ethernet driver"); - MODULE_AUTHOR("Andrew Victor"); -+MODULE_ALIAS("platform:" DRV_NAME); ---- a/drivers/net/arm/at91_ether.h -+++ b/drivers/net/arm/at91_ether.h -@@ -48,6 +48,9 @@ - /* Altima AC101L PHY */ - #define MII_AC101L_ID 0x00225520 - -+/* Micrel KSZ8041 PHY */ -+#define MII_KSZ8041_ID 0x00221510 -+ - /* Micrel KS8721 PHY */ - #define MII_KS8721_ID 0x00221610 - -@@ -84,7 +87,6 @@ struct recv_desc_bufs - - struct at91_private - { -- struct net_device_stats stats; - struct mii_if_info mii; /* ethtool support */ - struct at91_eth_data board_data; /* board-specific configuration */ - struct clk *ether_clk; /* clock */ ---- /dev/null -+++ b/drivers/net/arm/ks8695_ether.c -@@ -0,0 +1,1009 @@ -+/* -+ * Ethernet driver for the Kendin/Micrel KS8695. -+ * -+ * Copyright (C) 2006 Andrew Victor -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version -+ * 2 of the License, or (at your option) any later version. -+ */ -+ -+#include <linux/module.h> -+#include <linux/init.h> -+#include <linux/mii.h> -+#include <linux/netdevice.h> -+#include <linux/etherdevice.h> -+#include <linux/skbuff.h> -+#include <linux/dma-mapping.h> -+#include <linux/delay.h> -+#include <linux/ethtool.h> -+#include <linux/platform_device.h> -+ -+#include <asm/io.h> -+#include <asm/mach/irq.h> -+#include <asm/uaccess.h> -+#include <asm/arch/regs-wan.h> -+#include <asm/arch/regs-lan.h> -+#include <asm/arch/regs-hpna.h> -+#include <asm/arch/regs-switch.h> -+#include <asm/arch/regs-misc.h> -+ -+#include <asm/arch/regs-irq.h> -+ -+#include "ks8695_ether.h" -+ -+ -+#define DRV_NAME "ks8695_ether" -+#define DRV_VERSION "0.01" -+ -+/* ..................................................................... */ -+ -+static inline unsigned long ks8695_read(struct net_device *dev, unsigned int reg) -+{ -+ return __raw_readl(dev->base_addr + reg); -+} -+ -+static inline void ks8695_write(struct net_device *dev, unsigned int reg, unsigned long value) -+{ -+ __raw_writel(value, dev->base_addr + reg); -+} -+ -+ -+/* ......................... ADDRESS MANAGEMENT ........................ */ -+ -+#define KS8695_NR_ADDRESSES 16 -+ -+/* -+ * Add the specified multicast addresses to the Additional Station -+ * Address registers. -+ */ -+static void ks8695_set_mcast_address(struct net_device *dev, struct dev_mc_list *addr, int nr_addr) -+{ -+ unsigned long low, high; -+ int i; -+ -+ /* Set multicast addresses in Additional Station Address registers */ -+ for (i = 0; i < nr_addr; i++, addr = addr->next) { -+ if (!addr) break; /* unexpected end of list */ -+ else if (i == KS8695_NR_ADDRESSES) break; /* too many addresses */ -+ -+ low = (addr->dmi_addr[2] << 24) | (addr->dmi_addr[3] << 16) | (addr->dmi_addr[4] << 8) | (addr->dmi_addr[5]); -+ high = (addr->dmi_addr[0] << 8) | (addr->dmi_addr[1]); -+ -+ ks8695_write(dev, KS8695_WMAAL_(i), low); -+ ks8695_write(dev, KS8695_WMAAH_(i), WMAAH_E | high); -+ } -+ -+ /* Clear the remaining Additional Station Addresses */ -+ for (; i < KS8695_NR_ADDRESSES; i++) { -+ ks8695_write(dev, KS8695_WMAAL_(i), 0); -+ ks8695_write(dev, KS8695_WMAAH_(i), 0); -+ } -+} -+ -+/* -+ * Enable/Disable promiscuous and multicast modes. -+ */ -+static void ks8695eth_set_multi(struct net_device *dev) -+{ -+ unsigned long ctrl; -+ -+ ctrl = ks8695_read(dev, KS8695_WMDRXC); -+ -+ if (dev->flags & IFF_PROMISC) /* enable promiscuous mode */ -+ ctrl |= WMDRXC_WMRA; -+ else if (dev->flags & ~IFF_PROMISC) /* disable promiscuous mode */ -+ ctrl &= ~WMDRXC_WMRA; -+ -+ if (dev->flags & IFF_ALLMULTI) /* enable all multicast mode */ -+ ctrl |= WMDRXC_WMRM; -+ else if (dev->mc_count > KS8695_NR_ADDRESSES) /* more specific multicast addresses than can be handled in hardware */ -+ ctrl |= WMDRXC_WMRM; -+ else if (dev->mc_count > 0) { /* enable specific multicasts */ -+ ctrl &= ~WMDRXC_WMRM; -+ ks8695_set_mcast_address(dev, dev->mc_list, dev->mc_count); -+ } -+ else if (dev->flags & ~IFF_ALLMULTI) { /* disable multicast mode */ -+ ctrl &= ~WMDRXC_WMRM; -+ ks8695_set_mcast_address(dev, NULL, 0); -+ } -+ -+ ks8695_write(dev, KS8695_WMDRXC, ctrl); -+} -+ -+/* -+ * Program the hardware MAC address from dev->dev_addr. -+ */ -+static void update_mac_address(struct net_device *dev) -+{ -+ unsigned long low, high; -+ -+ low = (dev->dev_addr[2] << 24) | (dev->dev_addr[3] << 16) | (dev->dev_addr[4] << 8) | (dev->dev_addr[5]); -+ high = (dev->dev_addr[0] << 8) | (dev->dev_addr[1]); -+ -+ ks8695_write(dev, KS8695_WMAL, low); -+ ks8695_write(dev, KS8695_WMAH, high); -+} -+ -+/* -+ * Store the new hardware address in dev->dev_addr, and update the MAC. -+ */ -+static int ks8695eth_set_mac(struct net_device *dev, void* addr) -+{ -+ struct sockaddr *address = addr; -+ DECLARE_MAC_BUF(mac); -+ -+ if (!is_valid_ether_addr(address->sa_data)) -+ return -EADDRNOTAVAIL; -+ -+ memcpy(dev->dev_addr, address->sa_data, dev->addr_len); -+ update_mac_address(dev); -+ -+ printk("%s: Setting MAC address to %s\n", dev->name, print_mac(mac, dev->dev_addr)); -+ -+ return 0; -+} -+ -+/* -+ * Retrieve the MAC address set by the bootloader. -+ */ -+static void __init get_mac_address(struct net_device *dev) -+{ -+ unsigned char addr[6]; -+ unsigned long low, high; -+ -+ low = ks8695_read(dev, KS8695_WMAL); -+ high = ks8695_read(dev, KS8695_WMAH); -+ -+ addr[0] = (high & 0xff00) >> 8; -+ addr[1] = (high & 0xff); -+ addr[2] = (low & 0xff000000) >> 24; -+ addr[3] = (low & 0xff0000) >> 16; -+ addr[4] = (low & 0xff00) >> 8; -+ addr[5] = (low & 0xff); -+ -+ if (is_valid_ether_addr(addr)) -+ memcpy(dev->dev_addr, &addr, 6); -+} -+ -+ -+/* ......................... ETHTOOL SUPPORT ........................... */ -+ -+/* -+ * Get device-specific settings. -+ */ -+static int ks8695eth_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) -+{ -+ unsigned long ctrl; -+ -+ /* the defaults for all ports */ -+ cmd->supported = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full -+ | SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full -+ | SUPPORTED_TP | SUPPORTED_MII; -+ cmd->advertising = ADVERTISED_TP | ADVERTISED_MII; -+ cmd->port = PORT_MII; -+ cmd->transceiver = XCVR_INTERNAL; -+ -+ if (dev->base_addr == KS8695_HPNA_VA) { -+ cmd->phy_address = 0; -+ cmd->autoneg = AUTONEG_DISABLE; /* not supported for HPNA */ -+ -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_HMC); -+ cmd->speed = (ctrl & HMC_HSS) ? SPEED_100 : SPEED_10; -+ cmd->duplex = (ctrl & HMC_HDS) ? DUPLEX_FULL : DUPLEX_HALF; -+ } -+ else if (dev->base_addr == KS8695_WAN_VA) { -+ cmd->supported |= (SUPPORTED_Autoneg | SUPPORTED_Pause); -+ cmd->phy_address = 0; -+ -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_WMC); -+ if ((ctrl & WMC_WAND) == 0) { /* auto-negotiation is enabled */ -+ cmd->advertising |= ADVERTISED_Autoneg; -+ if (ctrl & WMC_WANA100F) -+ cmd->advertising |= ADVERTISED_100baseT_Full; -+ if (ctrl & WMC_WANA100H) -+ cmd->advertising |= ADVERTISED_100baseT_Half; -+ if (ctrl & WMC_WANA10F) -+ cmd->advertising |= ADVERTISED_10baseT_Full; -+ if (ctrl & WMC_WANA10H) -+ cmd->advertising |= ADVERTISED_10baseT_Half; -+ if (ctrl & WMC_WANAP) -+ cmd->advertising |= ADVERTISED_Pause; -+ cmd->autoneg = AUTONEG_ENABLE; -+ -+ cmd->speed = (ctrl & WMC_WSS) ? SPEED_100 : SPEED_10; -+ cmd->duplex = (ctrl & WMC_WDS) ? DUPLEX_FULL : DUPLEX_HALF; -+ } -+ else { /* auto-negotiation is disabled */ -+ cmd->autoneg = AUTONEG_DISABLE; -+ -+ cmd->speed = (ctrl & WMC_WANF100) ? SPEED_100 : SPEED_10; -+ cmd->duplex = (ctrl & WMC_WANFF) ? DUPLEX_FULL : DUPLEX_HALF; -+ } -+ } -+ else if (dev->base_addr == KS8695_LAN_VA) { -+ // TODO: Implement for Switch ports -+ } -+ -+ return 0; -+} -+ -+/* -+ * Set device-specific settings. -+ */ -+static int ks8695eth_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) -+{ -+ unsigned long ctrl; -+ -+ if ((cmd->speed != SPEED_10) && (cmd->speed != SPEED_100)) -+ return -EINVAL; -+ if ((cmd->duplex != DUPLEX_HALF) && (cmd->duplex != DUPLEX_FULL)) -+ return -EINVAL; -+ if (cmd->port != PORT_MII) -+ return -EINVAL; -+ if (cmd->transceiver != XCVR_INTERNAL) -+ return -EINVAL; -+ if ((cmd->autoneg != AUTONEG_DISABLE) && (cmd->autoneg != AUTONEG_ENABLE)) -+ return -EINVAL; -+ -+ if (cmd->autoneg == AUTONEG_ENABLE) { -+ if ((cmd->advertising & (ADVERTISED_10baseT_Half | -+ ADVERTISED_10baseT_Full | -+ ADVERTISED_100baseT_Half | -+ ADVERTISED_100baseT_Full)) == 0) -+ return -EINVAL; -+ -+ if (dev->base_addr == KS8695_HPNA_VA) -+ return -EINVAL; /* HPNA does not support auto-negotiation. */ -+ else if (dev->base_addr == KS8695_WAN_VA) { -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_WMC); -+ -+ ctrl &= ~(WMC_WAND | WMC_WANA100F | WMC_WANA100H | WMC_WANA10F | WMC_WANA10H); -+ if (cmd->advertising & ADVERTISED_100baseT_Full) -+ ctrl |= WMC_WANA100F; -+ if (cmd->advertising & ADVERTISED_100baseT_Half) -+ ctrl |= WMC_WANA100H; -+ if (cmd->advertising & ADVERTISED_10baseT_Full) -+ ctrl |= WMC_WANA10F; -+ if (cmd->advertising & ADVERTISED_10baseT_Half) -+ ctrl |= WMC_WANA10H; -+ -+ ctrl |= WMC_WANR; /* force a re-negotiation */ -+ __raw_writel(ctrl, KS8695_MISC_VA + KS8695_WMC); -+ } -+ else if (dev->base_addr == KS8695_LAN_VA) { -+ // TODO: Implement for Switch ports -+ } -+ -+ } -+ else { -+ if (dev->base_addr == KS8695_HPNA_VA) { -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_HMC); -+ -+ ctrl &= ~(HMC_HSS | HMC_HDS); -+ if (cmd->speed == SPEED_100) -+ ctrl |= HMC_HSS; -+ if (cmd->duplex == DUPLEX_FULL) -+ ctrl |= HMC_HDS; -+ -+ __raw_writel(ctrl, KS8695_MISC_VA + KS8695_HMC); -+ } -+ else if (dev->base_addr == KS8695_WAN_VA) { -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_WMC); -+ -+ ctrl |= WMC_WAND; /* disable auto-negotiation */ -+ ctrl &= ~(WMC_WANF100 | WMC_WANFF); -+ if (cmd->speed == SPEED_100) -+ ctrl |= WMC_WANF100; -+ if (cmd->duplex == DUPLEX_FULL) -+ ctrl |= WMC_WANFF; -+ -+ __raw_writel(ctrl, KS8695_MISC_VA + KS8695_WMC); -+ } -+ else if (dev->base_addr == KS8695_LAN_VA) { -+ // TODO: Implement for Switch ports -+ } -+ } -+ -+ return 0; -+} -+ -+/* -+ * Restart the auto-negotiation. -+ */ -+static int ks8695eth_nwayreset(struct net_device *dev) -+{ -+ unsigned long ctrl; -+ -+ if (dev->base_addr == KS8695_HPNA_VA) /* HPNA has no auto-negotiation */ -+ return -EINVAL; -+ else if (dev->base_addr == KS8695_WAN_VA) { -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_WMC); -+ -+ if ((ctrl & WMC_WAND) == 0) -+ __raw_writel(ctrl | WMC_WANR, KS8695_MISC_VA + KS8695_WMC); -+ else -+ return -EINVAL; /* auto-negitiation not enabled */ -+ } -+ else if (dev->base_addr == KS8695_LAN_VA) { -+ // TODO: Implement for Switch ports -+ } -+ -+ return 0; -+} -+ -+static void ks8695eth_get_pause(struct net_device *dev, struct ethtool_pauseparam *param) -+{ -+ unsigned long ctrl; -+ -+ if (dev->base_addr == KS8695_HPNA_VA) -+ return; -+ else if (dev->base_addr == KS8695_WAN_VA) { -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_WMC); /* advertise Pause */ -+ param->autoneg = (ctrl & WMC_WANAP); -+ -+ ctrl = ks8695_read(dev, KS8695_WMDRXC); /* current Tx Flow-control */ -+ param->rx_pause = (ctrl & WMDRXC_WMRFCE); -+ -+ ctrl = ks8695_read(dev, KS8695_WMDRXC); /* current Rx Flow-control */ -+ param->tx_pause = (ctrl & WMDTXC_WMTFCE); -+ } -+ else if (dev->base_addr == KS8695_LAN_VA) { -+ // TODO: Implement for Switch ports -+ } -+} -+ -+static int ks8695eth_set_pause(struct net_device *dev, struct ethtool_pauseparam *param) -+{ -+ // TODO. -+ -+ return 0; -+} -+ -+static u32 ks8695eth_get_link(struct net_device *dev) -+{ -+ unsigned long ctrl; -+ -+ if (dev->base_addr == KS8695_HPNA_VA) -+ return 1; /* HPNA always has link */ -+ else if (dev->base_addr == KS8695_WAN_VA) { -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_WMC); -+ return (ctrl & WMC_WLS); -+ } -+ else if (dev->base_addr == KS8695_LAN_VA) { -+ // TODO: Implement for Switch ports -+ } -+ -+ return 0; -+} -+ -+/* -+ * Report driver information. -+ */ -+static void ks8695eth_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info) -+{ -+ strlcpy(info->driver, DRV_NAME, sizeof(info->driver)); -+ strlcpy(info->version, DRV_VERSION, sizeof(info->version)); -+ strlcpy(info->bus_info, dev->dev.parent->bus_id, sizeof(info->bus_info)); -+} -+ -+static struct ethtool_ops ks8695eth_ethtool_ops = { -+ .get_settings = ks8695eth_get_settings, -+ .set_settings = ks8695eth_set_settings, -+ .get_drvinfo = ks8695eth_get_drvinfo, -+ .nway_reset = ks8695eth_nwayreset, -+ .get_pauseparam = ks8695eth_get_pause, -+ .set_pauseparam = ks8695eth_set_pause, -+ .get_link = ks8695eth_get_link, -+}; -+ -+ -+/* ................................ MAC ................................ */ -+ -+/* -+ * Setup the RX DMA descriptors, and enable and start the DMA receiver. -+ */ -+static void ks8695eth_start_rx(struct net_device *dev) -+{ -+ struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ unsigned long ctrl; -+ int i; -+ -+ /* Setup the DMA descriptors */ -+ for (i = 0; i < MAX_RX_DESC; i++) { -+ lp->rxdma[i].length = MAX_RXBUF_SIZE; -+ lp->rxdma[i].addr = (unsigned long) lp->rxSkb[i].dma; -+ lp->rxdma[i].next = (unsigned long) lp->rxdma_phys + (sizeof(struct rx_descriptor) * (i+1)); -+ lp->rxdma[i].status = RDES_OWN; -+ } -+ -+ /* Create ring of DMA descriptors */ -+ lp->rxdma[MAX_RX_DESC-1].next = (unsigned long) lp->rxdma_phys; /* phys address of 1st descriptor */ -+ -+ /* Reset receive index (since hardware was reset) */ -+ lp->rx_idx = 0; -+ -+ /* Program address of 1st descriptor in KS8695 */ -+ ks8695_write(dev, KS8695_WRDLB, (unsigned long) lp->rxdma_phys); -+ -+ /* Enable and start the DMA Receiver */ -+ ctrl = ks8695_read(dev, KS8695_WMDRXC); -+ ks8695_write(dev, KS8695_WMDRXC, ctrl | WMDRXC_WMRE); -+ ks8695_write(dev, KS8695_WMDRSC, 0); -+} -+ -+/* -+ * Stop the DMA receiver. -+ */ -+static void ks8695eth_stop_rx(struct net_device *dev) -+{ -+ unsigned long ctrl; -+ -+ /* Disable receive DMA */ -+ ctrl = ks8695_read(dev, KS8695_WMDRXC); -+ ks8695_write(dev, KS8695_WMDRXC, ctrl & ~WMDRXC_WMRE); -+} -+ -+/* -+ * Setup the TX DMA descriptors, and enable DMA transmitter. -+ */ -+static void ks8695eth_start_tx(struct net_device *dev) -+{ -+ struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ unsigned long ctrl; -+ int i; -+ -+ /* Setup the DMA descriptors */ -+ for (i = 0; i < MAX_TX_DESC; i++) { -+ lp->txdma[i].ownership = 0; -+ lp->txdma[i].status = 0; -+ lp->txdma[i].addr = 0; -+ lp->txdma[i].next = (unsigned long) lp->txdma_phys + (sizeof(struct tx_descriptor) * (i+1)); -+ } -+ -+ /* Create ring of DMA descriptors */ -+ lp->txdma[MAX_TX_DESC-1].next = (unsigned long) lp->txdma_phys; /* phys address of 1st desc */ -+ -+ /* Reset transmit indexes (since hardware was reset) */ -+ lp->tx_head = 0; -+ lp->tx_tail = 0; -+ -+ /* Program address of 1st descriptor in KS8695 */ -+ ks8695_write(dev, KS8695_WTDLB, (unsigned long) lp->txdma_phys); -+ -+ /* Enable the DMA transmitter (will be started on first packet) */ -+ ctrl = ks8695_read(dev, KS8695_WMDTXC); -+ ks8695_write(dev, KS8695_WMDTXC, ctrl | WMDTXC_WMTE); -+} -+ -+/* -+ * Stop the DMA transmitter. -+ */ -+static void ks8695eth_stop_tx(struct net_device *dev) -+{ -+ struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ unsigned long ctrl; -+ int i; -+ -+ /* Disable transmit DMA */ -+ ctrl = ks8695_read(dev, KS8695_WMDTXC); -+ ks8695_write(dev, KS8695_WMDTXC, ctrl & ~WMDTXC_WMTE); -+ -+ /* Clear any pending skb's still on transmit queue */ -+ for (i = 0; i < MAX_TX_DESC; i++) { -+ lp->txdma[i].ownership = 0; -+ lp->txdma[i].status = 0; -+ lp->txdma[i].addr = 0; -+ -+ if (lp->txSkb[i].skb) { -+ dma_unmap_single(lp->dev, lp->txSkb[i].dma, lp->txSkb[i].length, DMA_TO_DEVICE); -+ dev_kfree_skb_irq(lp->txSkb[i].skb); -+ lp->txSkb[i].skb = NULL; -+ } -+ } -+} -+ -+/* -+ * Reset the MAC hardware. -+ */ -+static void ks8695eth_hw_reset(struct net_device *dev) -+{ -+ /* Perform hardware reset */ -+ ks8695_write(dev, KS8695_WMDTXC, WMDTXC_WMTRST); -+ while (ks8695_read(dev, KS8695_WMDTXC) & WMDTXC_WMTRST) { barrier(); } -+ -+ /* Initialize the hardware */ -+ ks8695_write(dev, KS8695_WMDRXC, WMDRXC_WMRU | WMDRXC_WMRB); /* RX: receive Unicast & Broadcast */ -+ ks8695_write(dev, KS8695_WMDTXC, WMDTXC_WMTEP | WMDTXC_WMTAC); /* TX: add Padding & CRC */ -+ -+ // TODO: Can set Rx/Tx PBL: (Micrel using 8) -+ // TODO: Enable hardware checksumming. -+ // TODO: Enable Rx/Tx flow-control -+} -+ -+/* -+ * Enable or Disable the IRQs associated with a network interface. -+ */ -+static void ks8695eth_set_irq(struct net_device *dev, short enable) -+{ -+ struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ int i; -+ -+ for (i = 0; i < NR_IRQS; i++) { -+ if (lp->irqs & (1 << i)) { -+ if (enable) -+ enable_irq(i); -+ else -+ disable_irq(i); -+ } -+ } -+} -+ -+/* -+ * Open the ethernet interface. -+ */ -+static int ks8695eth_open(struct net_device *dev) -+{ -+ if (!is_valid_ether_addr(dev->dev_addr)) -+ return -EADDRNOTAVAIL; -+ -+ /* MUST reset hardware in _open() */ -+ ks8695eth_hw_reset(dev); -+ -+ /* Update the MAC address (incase user has changed it) */ -+ update_mac_address(dev); -+ -+ /* Start DMA */ -+ ks8695eth_start_tx(dev); -+ ks8695eth_start_rx(dev); -+ -+ /* Enable interrupts */ -+ ks8695eth_set_irq(dev, 1); -+ -+ netif_start_queue(dev); -+ return 0; -+} -+ -+/* -+ * Close the ethernet interface. -+ */ -+static int ks8695eth_close(struct net_device *dev) -+{ -+ /* Stop DMA */ -+ ks8695eth_stop_rx(dev); -+ ks8695eth_stop_tx(dev); -+ -+ /* Disable interrupts */ -+ ks8695eth_set_irq(dev, 0); -+ -+ netif_stop_queue(dev); -+ return 0; -+} -+ -+/* -+ * Return the current statistics. -+ */ -+static struct net_device_stats *ks8695eth_stats(struct net_device *dev) -+{ -+ return &dev->stats; -+} -+ -+/* -+ * Queue a packet for transmission in next TX DMA descriptor. -+ */ -+static int ks8695eth_xmit_frame(struct sk_buff *skb, struct net_device *dev) -+{ -+ struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ int i; -+ -+ /* Packets are added to head of array */ -+ i = lp->tx_head; -+ -+ /* Store packet information */ -+ lp->txSkb[i].skb = skb; -+ lp->txSkb[i].length = skb->len; -+ lp->txSkb[i].dma = dma_map_single(lp->dev, skb->data, skb->len, DMA_TO_DEVICE); -+ -+ spin_lock_irq(&lp->tx_lock); -+ -+ /* Set Tx descriptor information */ -+ lp->txdma[i].addr = lp->txSkb[i].dma; -+ lp->txdma[i].status = TDES_IC | TDES_FS | TDES_LS | (lp->txSkb[i].length & TDES_TBS); -+ lp->txdma[i].ownership = TDES_OWN; -+ -+ /* Start the DMA transmitter (if necessary) */ -+ ks8695_write(dev, KS8695_WMDTSC, 0); -+ -+ lp->tx_head = (lp->tx_head + 1) % MAX_TX_DESC; -+ if (lp->tx_head == lp->tx_tail) /* no more descriptors */ -+ netif_stop_queue(dev); -+ -+ spin_unlock_irq(&lp->tx_lock); -+ -+ dev->trans_start = jiffies; -+ return 0; -+} -+ -+/* ..................................................................... */ -+ -+/* -+ * The link state of the WAN port has changed. -+ * (Called from interrupt context) -+ */ -+static void ks8695eth_wan_link(struct net_device *dev) -+{ -+ unsigned long ctrl; -+ -+ ctrl = __raw_readl(KS8695_MISC_VA + KS8695_WMC); -+ if (ctrl & WMC_WLS) { -+ netif_carrier_on(dev); -+ printk(KERN_INFO "%s: Link is now %s-%s\n", dev->name, -+ (ctrl & WMC_WSS) ? "100" : "10", -+ (ctrl & WMC_WDS) ? "FullDuplex" : "HalfDuplex"); -+ } -+ else { -+ netif_carrier_off(dev); -+ printk(KERN_INFO "%s: Link down.\n", dev->name); -+ } -+} -+ -+/* ..................................................................... */ -+ -+/* -+ * A frame has been received. Exteract from buffer descriptor and deliver to -+ * upper layers. -+ * (Called from interrupt context) -+ */ -+static void ks8695eth_rx_interrupt(struct net_device *dev) -+{ -+ struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ struct sk_buff *skb; -+ unsigned long flags; -+ unsigned int pktlen; -+ -+ while (!(lp->rxdma[lp->rx_idx].status & RDES_OWN)) { -+ flags = lp->rxdma[lp->rx_idx].status; -+ -+ if ((flags & (RDES_FS | RDES_LS)) != (RDES_FS | RDES_LS)) { -+ printk(KERN_ERR "%s: Spanning packet detected\n", dev->name); -+ goto rx_complete; -+ } -+ -+ /* handle errors */ -+ if (flags & (RDES_ES | RDES_RE)) { -+ dev->stats.rx_errors++; -+ -+ if (flags & RDES_TL) /* Frame too long */ -+ dev->stats.rx_length_errors++; -+ else if (flags & RDES_RF) /* Runt frame */ -+ dev->stats.rx_length_errors++; -+ else if (flags & RDES_CE) /* CRC error */ -+ dev->stats.rx_crc_errors++; -+ else if (flags & RDES_RE) /* MII error */ -+ dev->stats.rx_missed_errors++; -+ // TODO: If hardware checksumming, then check IP/TCP/UDP errors. -+ -+ goto rx_complete; -+ } -+ -+ pktlen = flags & RDES_FLEN; -+ pktlen = pktlen - 4; /* remove CRC */ -+ -+ // OLD CALL: consistent_sync(lp->rxSkb[lp->rx_idx].skb->data, MAX_RXBUF_SIZE, DMA_FROM_DEVICE); -+ dma_sync_single_for_cpu(lp->dev, lp->rxSkb[lp->rx_idx].dma, MAX_RXBUF_SIZE, DMA_FROM_DEVICE); -+ -+ skb = dev_alloc_skb(pktlen+2); /* +2 to align IP header */ -+ if (!skb) { -+ dev->stats.rx_dropped++; -+ printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", dev->name); -+ goto rx_complete; -+ } -+ -+ skb_reserve(skb, 2); /* align IP header */ -+ memcpy(skb_put(skb, pktlen), lp->rxSkb[lp->rx_idx].skb->data, pktlen); -+ -+ skb->protocol = eth_type_trans(skb, dev); -+ netif_rx(skb); -+ -+ /* update statistics */ -+ dev->stats.rx_packets++; -+ dev->stats.rx_bytes += pktlen; -+ if (flags & RDES_MF) -+ dev->stats.multicast++; -+ dev->last_rx = jiffies; -+ -+rx_complete: -+ lp->rxdma[lp->rx_idx].status = RDES_OWN; /* reset ownership bit */ -+ -+ lp->rx_idx = (lp->rx_idx + 1) % MAX_RX_DESC; /* next descriptor */ -+ } -+ -+ /* restart DMA receiver incase it was suspended */ -+ ks8695_write(dev, KS8695_WMDRSC, 0); -+} -+ -+/* -+ * A packet has been transmitted. -+ * (Called from interrupt context) -+ */ -+static void ks8695eth_tx_interrupt(struct net_device *dev) -+{ -+ struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ int i; -+ -+ /* Packets are removed from tail of array */ -+ i = lp->tx_tail; -+ -+ // TODO: Loop through multiple times? -+ -+ if (lp->txSkb[i].skb) { -+ /* update statistics */ -+ dev->stats.tx_packets++; -+ dev->stats.tx_bytes += lp->txSkb[i].length; -+ -+ /* free packet */ -+ dma_unmap_single(lp->dev, lp->txSkb[i].dma, lp->txSkb[i].length, DMA_TO_DEVICE); -+ dev_kfree_skb_irq(lp->txSkb[i].skb); -+ lp->txSkb[i].skb = NULL; -+ -+ /* Not necessary to clear descriptor since we still own it */ -+ } -+ -+ lp->tx_tail = (lp->tx_tail + 1) % MAX_TX_DESC; -+ -+ netif_wake_queue(dev); -+} -+ -+/* -+ * MAC interrupt handler -+ */ -+static irqreturn_t ks8695eth_interrupt(int irq, void *dev_id) -+{ -+ struct net_device *dev = (struct net_device *) dev_id; -+ -+ switch (irq) { -+ case KS8695_IRQ_LAN_RX_STATUS: -+ case KS8695_IRQ_HPNA_RX_STATUS: -+ case KS8695_IRQ_WAN_RX_STATUS: -+ ks8695eth_rx_interrupt(dev); -+ return IRQ_HANDLED; -+ -+ case KS8695_IRQ_LAN_TX_STATUS: -+ case KS8695_IRQ_HPNA_TX_STATUS: -+ case KS8695_IRQ_WAN_TX_STATUS: -+ ks8695eth_tx_interrupt(dev); -+ return IRQ_HANDLED; -+ -+ case KS8695_IRQ_WAN_LINK: -+ ks8695eth_wan_link(dev); -+ return IRQ_HANDLED; -+ -+ default: -+ return IRQ_NONE; -+ } -+} -+ -+ -+/* ..................................................................... */ -+ -+/* -+ * Initialize the WAN hardware to known defaults. -+ */ -+static void __init ks8695eth_init_wan(void) -+{ -+ unsigned long ctrl; -+ -+ /* Support auto-negotiation */ -+ ctrl = WMC_WANAP | WMC_WANA100F | WMC_WANA100H | WMC_WANA10F | WMC_WANA10H; -+ -+ /* LED0 = Activity , LED1 = Link */ -+ ctrl |= (WLED0S_ACTIVITY | WLED1S_LINK); -+ -+ /* Restart Auto-negotiation */ -+ ctrl |= WMC_WANR; -+ -+ __raw_writel(ctrl, KS8695_MISC_VA + KS8695_WMC); -+ -+ __raw_writel(0, KS8695_MISC_VA + KS8695_WPPM); -+ __raw_writel(0, KS8695_MISC_VA + KS8695_PPS); -+} -+ -+/* -+ * Initialize the LAN Switch hardware to known defaults. -+ */ -+static void __init ks8695eth_init_switch(void) -+{ -+ unsigned long ctrl; -+ -+ ctrl = 0x40819e00; /* default */ -+ -+ /* LED0 = Speed LED1 = Link/Activity */ -+ ctrl &= ~(SEC0_LLED1S | SEC0_LLED0S); -+ ctrl |= (LLED0S_LINK | LLED1S_LINK_ACTIVITY); -+ -+ /* Enable Switch */ -+ ctrl |= SEC0_ENABLE; -+ -+ __raw_writel(ctrl, KS8695_SWITCH_VA + KS8695_SEC0); -+ -+ __raw_writel(0x9400100, KS8695_SWITCH_VA + KS8695_SEC1); /* reset defaults */ -+} -+ -+static int ks8695eth_hook_irqs(struct platform_device *pdev, struct net_device *dev, unsigned long *irqset) -+{ -+ struct resource *res; -+ int i = 0, ret; -+ -+ while ((res = platform_get_resource(pdev, IORESOURCE_IRQ, i))) { -+ set_irq_flags(res->start, IRQF_VALID | IRQF_NOAUTOEN); -+ -+ ret = request_irq(res->start, ks8695eth_interrupt, IRQF_DISABLED | IRQF_SHARED, res->name, dev); -+ if (ret) { -+ printk(KERN_ERR "%s: return_irq %u failed\n", dev->name, res->start); -+ return -EBUSY; -+ } -+ -+ *irqset |= (1 << res->start); -+ -+ // TODO: Can set different priorities for interrupts [0x BB AA FF]. -+ -+ i++; -+ } -+ -+ return 0; -+} -+ -+static int __init ks8695eth_probe(struct platform_device *pdev) -+{ -+ struct net_device *dev; -+ struct ks8695eth_priv *lp; -+ struct resource *res; -+ int i = 0, ret, size; -+ DECLARE_MAC_BUF(mac); -+ -+ /* Create ethernet device */ -+ dev = alloc_etherdev(sizeof(struct ks8695eth_priv)); -+ if (!dev) -+ return -ENOMEM; -+ -+ /* Get I/O base address */ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ if (!res) { -+ free_netdev(dev); -+ return -ENODEV; -+ } -+ dev->base_addr = res->start; -+ -+ lp = (struct ks8695eth_priv *) dev->priv; -+ -+ /* Retreive MAC address before the MAC registers are reset */ -+ get_mac_address(dev); -+ -+ /* Reset the hardware */ -+ ks8695_write(dev, KS8695_WMDTXC, WMDTXC_WMTRST); -+ while (ks8695_read(dev, KS8695_WMDTXC) & WMDTXC_WMTRST) { barrier(); } -+ -+ /* Get IRQ's */ -+ dev->irq = platform_get_irq(pdev, 0); -+ ret = ks8695eth_hook_irqs(pdev, dev, &lp->irqs); -+ if (ret) { -+ // Cleanup. -+ } -+ -+ /* Allocate DMA-able memory for Tx descriptor */ -+ size = sizeof(struct tx_descriptor) * MAX_TX_DESC; -+ lp->txdma = dma_alloc_coherent(&pdev->dev, size, &lp->txdma_phys, GFP_KERNEL); -+ if (lp->txdma == NULL) { -+ // free IRQs -+ free_netdev(dev); -+ return -ENOMEM; -+ } -+ memset(lp->txdma, 0, size); -+ lp->tx_head = 0; -+ lp->tx_tail = 0; -+ -+ /* Allocate DMA-able memory for Rx descriptor */ -+ size = sizeof(struct rx_descriptor) * MAX_RX_DESC; -+ lp->rxdma = dma_alloc_coherent(&pdev->dev, size, &lp->rxdma_phys, GFP_KERNEL); -+ if (lp->rxdma == NULL) { -+ // free IRQs -+ // Free TX descriptor memory. -+ free_netdev(dev); -+ return -ENOMEM; -+ } -+ memset(lp->rxdma, 0, size); -+ lp->rx_idx = 0; -+ -+ /* Allocate DMA-able memory for Rx Data */ -+ for (i = 0; i < MAX_RX_DESC; i++) { -+ lp->rxSkb[i].skb = alloc_skb(MAX_RXBUF_SIZE, GFP_KERNEL); -+ if (lp->rxSkb[i].skb == NULL) { -+ // Cleanup -+ return -ENOMEM; -+ } -+ lp->rxSkb[i].length = MAX_RXBUF_SIZE; -+ lp->rxSkb[i].dma = dma_map_single(&pdev->dev, lp->rxSkb[i].skb->data, MAX_RXBUF_SIZE, DMA_FROM_DEVICE); -+ } -+ -+ spin_lock_init(&lp->tx_lock); -+ -+ platform_set_drvdata(pdev, dev); -+ -+ ether_setup(dev); -+ dev->open = ks8695eth_open; -+ dev->stop = ks8695eth_close; -+ dev->hard_start_xmit = ks8695eth_xmit_frame; -+ dev->get_stats = ks8695eth_stats; -+ dev->set_multicast_list = ks8695eth_set_multi; -+ dev->set_mac_address = ks8695eth_set_mac; -+ dev->ethtool_ops = &ks8695eth_ethtool_ops; -+ -+ SET_NETDEV_DEV(dev, &pdev->dev); -+ lp->dev = &pdev->dev; -+ -+ if (dev->base_addr == KS8695_WAN_VA) -+ ks8695eth_init_wan(); -+ else if (dev->base_addr == KS8695_LAN_VA) -+ ks8695eth_init_switch(); -+ -+ /* Register the network interface */ -+ ret = register_netdev(dev); -+ if (ret) { -+ // free IRQs -+ free_netdev(dev); -+// dma_free_coherent(&pdev->dev, sizeof(struct ks8695_tx_dma), lp->txdma, lp->txdma_phys); -+// dma_free_coherent(&pdev->dev, sizeof(struct ks8695_rx_dma), lp->rxdma, lp->rxdma_phys); -+ return ret; -+ } -+ -+ printk(KERN_INFO "%s: KS8695 ethernet (%s)\n", dev->name, print_mac(mac, dev->dev_addr)); -+ -+ return 0; -+} -+ -+static int __devexit ks8695eth_remove(struct platform_device *pdev) -+{ -+ struct net_device *dev = platform_get_drvdata(pdev); -+// struct ks8695eth_priv *lp = (struct ks8695eth_priv *) dev->priv; -+ -+ unregister_netdev(dev); -+ -+ // Free IRQ -+// dma_free_coherent(&pdev->dev, sizeof(struct ks8695_tx_dma), lp->txdma, lp->txdma_phys); -+// dma_free_coherent(&pdev->dev, sizeof(struct ks8695_rx_dma), lp->rxdma, lp->rxdma_phys); -+ -+ platform_set_drvdata(pdev, NULL); -+ free_netdev(dev); -+ return 0; -+} -+ -+static struct platform_driver ks8695ether_driver = { -+ .probe = ks8695eth_probe, -+ .remove = __devexit_p(ks8695eth_remove), -+// .suspend = -+// .resume = -+ .driver = { -+ .name = DRV_NAME, -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+ -+static int __init ks8695eth_init(void) -+{ -+ return platform_driver_register(&ks8695ether_driver); -+} -+ -+static void __exit ks8695eth_exit(void) -+{ -+ platform_driver_unregister(&ks8695ether_driver); -+} -+ -+module_init(ks8695eth_init); -+module_exit(ks8695eth_exit); -+ -+MODULE_LICENSE("GPL"); -+MODULE_DESCRIPTION("KS8695 Ethernet driver"); -+MODULE_AUTHOR("Andrew Victor"); -+MODULE_ALIAS("platform:" DRV_NAME); ---- /dev/null -+++ b/drivers/net/arm/ks8695_ether.h -@@ -0,0 +1,92 @@ -+/* -+ * Ethernet driver for the Micrel/Kendin KS8695 (Centaur) -+ * -+ * (C) 2006 Andrew Victor -+ * -+ */ -+ -+#ifndef KS8695_ETHERNET -+#define KS8695_ETHERNET -+ -+/* .... Hardware Descriptors ................................................ */ -+ -+struct rx_descriptor { -+ unsigned long status; -+ unsigned long length; -+ unsigned long addr; -+ unsigned long next; -+}; -+ -+#define RDES_OWN (1 << 31) /* Ownership */ -+#define RDES_FS (1 << 30) /* First Descriptor */ -+#define RDES_LS (1 << 29) /* Last Descriptor */ -+#define RDES_IPE (1 << 28) /* IP Checksum error */ -+#define RDES_TCPE (1 << 27) /* TCP Checksum error */ -+#define RDES_UDPE (1 << 26) /* UDP Checksum error */ -+#define RDES_ES (1 << 25) /* Error summary */ -+#define RDES_MF (1 << 24) /* Multicast Frame */ -+#define RDES_RE (1 << 19) /* MII Error reported */ -+#define RDES_TL (1 << 18) /* Frame too Long */ -+#define RDES_RF (1 << 17) /* Runt Frame */ -+#define RDES_CE (1 << 16) /* CRC error */ -+#define RDES_FT (1 << 15) /* Frame Type */ -+#define RDES_FLEN (0x7ff) /* Frame Length */ -+ -+#define RDES_RER (1 << 25) /* Receive End of Ring */ -+#define RDES_RBS (0x7ff) /* Receive Buffer Size */ -+ -+ -+struct tx_descriptor { -+ unsigned long ownership; -+ unsigned long status; -+ unsigned long addr; -+ unsigned long next; -+}; -+ -+#define TDES_OWN (1 << 31) /* Ownership */ -+ -+#define TDES_IC (1 << 31) /* Interrupt on Completion */ -+#define TDES_FS (1 << 30) /* First Segment */ -+#define TDES_LS (1 << 29) /* Last Segment */ -+#define TDES_IPCKG (1 << 28) /* IP Checksum generate */ -+#define TDES_TCPCKG (1 << 27) /* TCP Checksum generate */ -+#define TDES_UDPCKG (1 << 26) /* UDP Checksum generate */ -+#define TDES_TER (1 << 25) /* Transmit End of Ring */ -+#define TDES_TBS (0x7ff) /* Transmit Buffer Size */ -+ -+ -+/* .... ..................................................................... */ -+ -+#define MAX_RX_DESC 16 /* number of receive descriptors */ -+#define MAX_TX_DESC 8 /* number of transmit descriptors */ -+#define MAX_RXBUF_SIZE 0x600 /* 1518 rounded-up */ -+ -+struct ks8695_buffer -+{ -+ struct sk_buff *skb; -+ dma_addr_t dma; -+ unsigned long length; -+}; -+ -+ -+struct ks8695eth_priv -+{ -+ struct device *dev; -+ unsigned long irqs; /* IRQ bitset */ -+ -+ /* Transmit */ -+ struct tx_descriptor *txdma; /* Tx DMA descriptors */ -+ dma_addr_t txdma_phys; /* TX DMA descriptors (phys address) */ -+ unsigned int tx_head; /* descriptor index (add) */ -+ unsigned int tx_tail; /* descriptor index (remove) */ -+ spinlock_t tx_lock; -+ struct ks8695_buffer txSkb[MAX_TX_DESC]; /* packets being transmitted */ -+ -+ /* Receive */ -+ struct rx_descriptor *rxdma; /* Rx DMA descriptors */ -+ dma_addr_t rxdma_phys; /* Rx DMA descriptors (phys address) */ -+ unsigned int rx_idx; /* descriptor index */ -+ struct ks8695_buffer rxSkb[MAX_RX_DESC]; -+}; -+ -+#endif ---- a/drivers/rtc/Kconfig -+++ b/drivers/rtc/Kconfig -@@ -487,12 +487,12 @@ config RTC_DRV_AT91RM9200 - this is powered by the backup power supply. - - config RTC_DRV_AT91SAM9 -- tristate "AT91SAM9x" -+ tristate "AT91SAM9x or AT91CAP9" - depends on ARCH_AT91 && !(ARCH_AT91RM9200 || ARCH_AT91X40) - help -- RTC driver for the Atmel AT91SAM9x internal RTT (Real Time Timer). -- These timers are powered by the backup power supply (such as a -- small coin cell battery), but do not need to be used as RTCs. -+ RTC driver for the Atmel AT91SAM9x and AT91CAP9 internal RTT (Real -+ Time Timer). These timers are powered by the backup power supply -+ (such as a small coin cell battery), but do not need to be used as RTCs. - - (On AT91SAM9rl chips you probably want to use the dedicated RTC - module and leave the RTT available for other uses.) ---- a/drivers/rtc/rtc-at91rm9200.c -+++ b/drivers/rtc/rtc-at91rm9200.c -@@ -29,9 +29,6 @@ - #include <linux/completion.h> - - #include <asm/uaccess.h> --#include <asm/rtc.h> -- --#include <asm/mach/time.h> - - #include <asm/arch/at91_rtc.h> - -@@ -307,12 +304,6 @@ static int __init at91_rtc_probe(struct - return ret; - } - -- /* cpu init code should really have flagged this device as -- * being wake-capable; if it didn't, do that here. -- */ -- if (!device_can_wakeup(&pdev->dev)) -- device_init_wakeup(&pdev->dev, 1); -- - rtc = rtc_device_register(pdev->name, &pdev->dev, - &at91_rtc_ops, THIS_MODULE); - if (IS_ERR(rtc)) { ---- a/drivers/rtc/rtc-at91sam9.c -+++ b/drivers/rtc/rtc-at91sam9.c -@@ -21,6 +21,7 @@ - - #include <asm/mach/time.h> - #include <asm/arch/board.h> -+#include <asm/arch/cpu.h> - #include <asm/arch/at91_rtt.h> - - -@@ -150,6 +151,9 @@ static int at91_rtc_settime(struct devic - return 0; - } - -+/* -+ * Read alarm time and date in RTC -+ */ - static int at91_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm) - { - struct sam9_rtc *rtc = dev_get_drvdata(dev); -@@ -176,6 +180,9 @@ static int at91_rtc_readalarm(struct dev - return 0; - } - -+/* -+ * Set alarm time and date in RTC -+ */ - static int at91_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm) - { - struct sam9_rtc *rtc = dev_get_drvdata(dev); -@@ -321,10 +328,6 @@ static int __init at91_rtc_probe(struct - if (!rtc) - return -ENOMEM; - -- /* platform setup code should have handled this; sigh */ -- if (!device_can_wakeup(&pdev->dev)) -- device_init_wakeup(&pdev->dev, 1); -- - platform_set_drvdata(pdev, rtc); - rtc->rtt = (void __force __iomem *) (AT91_VA_BASE_SYS - AT91_BASE_SYS); - rtc->rtt += r->start; ---- a/drivers/spi/Kconfig -+++ b/drivers/spi/Kconfig -@@ -113,6 +113,15 @@ config SPI_GPIO - - If unsure, say N. - -+config SPI_AT91 -+ tristate "AT91RM9200 Bitbang SPI Master" -+ depends on SPI_MASTER && ARCH_AT91RM9200 && !SPI_ATMEL && EXPERIMENTAL -+ select SPI_BITBANG -+ help -+ This is dumb PIO bitbanging driver for the Atmel AT91RM9200. -+ The SPI_ATMEL driver will be its replacement, using the native -+ SPI hardware and its DMA controller. -+ - config SPI_IMX - tristate "Freescale iMX SPI controller" - depends on SPI_MASTER && ARCH_IMX && EXPERIMENTAL ---- a/drivers/spi/Makefile -+++ b/drivers/spi/Makefile -@@ -29,6 +29,7 @@ obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24x - obj-$(CONFIG_SPI_TXX9) += spi_txx9.o - obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o - obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o -+obj-$(CONFIG_SPI_AT91) += spi_at91_bitbang.o - # ... add above this line ... - - # SPI protocol drivers (device/link on bus) ---- /dev/null -+++ b/drivers/spi/spi_at91_bitbang.c -@@ -0,0 +1,208 @@ -+/* -+ * at91_spi.c - at91 SPI driver (BOOTSTRAP/BITBANG VERSION) -+ * -+ * Copyright (C) 2006 David Brownell -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -+ */ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+ -+#include <linux/spi/spi.h> -+#include <linux/spi/spi_bitbang.h> -+ -+#include <asm/arch/gpio.h> -+ -+ -+/* -+ * FIXME this bitbanging version is just to help bootstrap systems until -+ * there's a native SPI+IRQ+DMA controller driver ... such a driver should -+ * be a drop-in replacement for this one, and much faster. -+ * -+ * remember: -+ * -+ * - other at91 parts (like at91sam9) have multiple controllers -+ * and different pin muxing; this version is at91rm9200 specfic. -+ * -+ * - at91sam9261 SPI0 pins are directly muxed with MMC/SD pins. -+ * -+ * - rm9200 spi chipselects drop wrongly, so the native driver -+ * will need to use gpios much like this does. -+ * -+ * - real hardware only allows 8..16 bits per word, while this -+ * bitbanger allows 1..32 (incompatible superset). -+ * -+ * - this disregards clock parameters. with inlined gpio calls, -+ * gcc 3.4.4 produces about 1.5 mbit/sec, more than 2x faster -+ * than using the subroutined veresion from txrx_word(). -+ * -+ * - suspend/resume and <linux/clk.h> support is missing ... -+ */ -+ -+#define spi_miso_bit AT91_PIN_PA0 -+#define spi_mosi_bit AT91_PIN_PA1 -+#define spi_sck_bit AT91_PIN_PA2 -+ -+struct at91_spi { -+ struct spi_bitbang bitbang; -+ struct platform_device *pdev; -+}; -+ -+/*----------------------------------------------------------------------*/ -+ -+static inline void setsck(struct spi_device *spi, int is_on) -+{ -+ at91_set_gpio_value(spi_sck_bit, is_on); -+} -+ -+static inline void setmosi(struct spi_device *spi, int is_on) -+{ -+ at91_set_gpio_value(spi_mosi_bit, is_on); -+} -+ -+static inline int getmiso(struct spi_device *spi) -+{ -+ return at91_get_gpio_value(spi_miso_bit); -+} -+ -+static void at91_spi_chipselect(struct spi_device *spi, int is_active) -+{ -+ unsigned long cs = (unsigned long) spi->controller_data; -+ -+ /* set default clock polarity */ -+ if (is_active) -+ setsck(spi, spi->mode & SPI_CPOL); -+ -+ /* only support active-low (default) */ -+ at91_set_gpio_value(cs, !is_active); -+} -+ -+/* -+ * NOTE: this is "as fast as we can"; it should be a function of -+ * the device clock ... -+ */ -+#define spidelay(X) do{} while(0) -+ -+#define EXPAND_BITBANG_TXRX -+#include <linux/spi/spi_bitbang.h> -+ -+static u32 at91_spi_txrx_word_mode0(struct spi_device *spi, -+ unsigned nsecs, u32 word, u8 bits) -+{ -+ return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, 8); -+} -+ -+static u32 at91_spi_txrx_word_mode1(struct spi_device *spi, -+ unsigned nsecs, u32 word, u8 bits) -+{ -+ return bitbang_txrx_be_cpha1(spi, nsecs, 0, word, 8); -+} -+ -+static u32 at91_spi_txrx_word_mode2(struct spi_device *spi, -+ unsigned nsecs, u32 word, u8 bits) -+{ -+ return bitbang_txrx_be_cpha0(spi, nsecs, 1, word, 8); -+} -+ -+static u32 at91_spi_txrx_word_mode3(struct spi_device *spi, -+ unsigned nsecs, u32 word, u8 bits) -+{ -+ return bitbang_txrx_be_cpha1(spi, nsecs, 1, word, 8); -+} -+ -+/*----------------------------------------------------------------------*/ -+ -+static int __init at91_spi_probe(struct platform_device *pdev) -+{ -+ int status; -+ struct spi_master *master; -+ struct at91_spi *at91_spi; -+ -+ if (pdev->id != 0) /* SPI0 bus */ -+ return -EINVAL; -+ -+ master = spi_alloc_master(&pdev->dev, sizeof *at91_spi); -+ if (!master) -+ return -ENOMEM; -+ -+ at91_spi = spi_master_get_devdata(master); -+ at91_spi->pdev = pdev; -+ platform_set_drvdata(pdev, at91_spi); -+ -+ /* SPI and bitbang hookup */ -+ master->bus_num = 0; -+ master->num_chipselect = 4; -+ -+ at91_spi->bitbang.master = spi_master_get(master); -+ at91_spi->bitbang.chipselect = at91_spi_chipselect; -+ at91_spi->bitbang.txrx_word[SPI_MODE_0] = at91_spi_txrx_word_mode0; -+ at91_spi->bitbang.txrx_word[SPI_MODE_1] = at91_spi_txrx_word_mode1; -+ at91_spi->bitbang.txrx_word[SPI_MODE_2] = at91_spi_txrx_word_mode2; -+ at91_spi->bitbang.txrx_word[SPI_MODE_3] = at91_spi_txrx_word_mode3; -+ -+ status = spi_bitbang_start(&at91_spi->bitbang); -+ if (status < 0) -+ (void) spi_master_put(at91_spi->bitbang.master); -+ -+ return status; -+} -+ -+static int __exit at91_spi_remove(struct platform_device *pdev) -+{ -+ struct at91_spi *at91_spi = platform_get_drvdata(pdev); -+ int status; -+ -+ /* stop() unregisters child devices too */ -+ status = spi_bitbang_stop(&at91_spi->bitbang); -+ (void) spi_master_put(at91_spi->bitbang.master); -+ -+ platform_set_drvdata(pdev, NULL); -+ return status; -+} -+ -+static struct platform_driver at91_spi_driver = { -+ .probe = at91_spi_probe, -+ .remove = __exit_p(at91_spi_remove), -+ .driver = { -+ .name = "at91_spi", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+static int __init at91_spi_init(void) -+{ -+ at91_set_gpio_output(spi_sck_bit, 0); -+ at91_set_gpio_output(spi_mosi_bit, 0); -+ at91_set_gpio_input(spi_miso_bit, 1 /* pullup */); -+ -+ /* register driver */ -+ return platform_driver_register(&at91_spi_driver); -+} -+ -+static void __exit at91_spi_exit(void) -+{ -+ platform_driver_unregister(&at91_spi_driver); -+} -+ -+device_initcall(at91_spi_init); -+module_exit(at91_spi_exit); -+ -+MODULE_ALIAS("at91_spi.0"); -+ -+MODULE_DESCRIPTION("AT91 SPI support (BOOTSTRAP/BITBANG VERSION)"); -+MODULE_AUTHOR("David Brownell"); -+MODULE_LICENSE("GPL"); -+MODULE_ALIAS("platform:at91_spi"); ---- a/drivers/usb/gadget/Kconfig -+++ b/drivers/usb/gadget/Kconfig -@@ -118,10 +118,10 @@ config USB_AMD5536UDC - config USB_GADGET_ATMEL_USBA - boolean "Atmel USBA" - select USB_GADGET_DUALSPEED -- depends on AVR32 -+ depends on AVR32 || ARCH_AT91CAP9 || ARCH_AT91SAM9RL - help - USBA is the integrated high-speed USB Device controller on -- the AT32AP700x processors from Atmel. -+ the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel. - - config USB_ATMEL_USBA - tristate ---- a/drivers/usb/gadget/at91_udc.c -+++ b/drivers/usb/gadget/at91_udc.c -@@ -1827,7 +1827,7 @@ static int at91udc_suspend(struct platfo - */ - if ((!udc->suspended && udc->addr) - || !wake -- || at91_suspend_entering_slow_clock()) { -+ || clk_must_disable(udc->fclk)) { - pullup(udc, 0); - wake = 0; - } else ---- a/drivers/usb/gadget/atmel_usba_udc.c -+++ b/drivers/usb/gadget/atmel_usba_udc.c -@@ -18,6 +18,7 @@ - #include <linux/platform_device.h> - #include <linux/usb/ch9.h> - #include <linux/usb/gadget.h> -+#include <linux/usb/atmel_usba_udc.h> - #include <linux/delay.h> - - #include <asm/gpio.h> -@@ -27,6 +28,7 @@ - - - static struct usba_udc the_udc; -+static struct usba_ep *usba_ep; - - #ifdef CONFIG_USB_GADGET_DEBUG_FS - #include <linux/debugfs.h> -@@ -324,53 +326,6 @@ static int vbus_is_present(struct usba_u - return 1; - } - --static void copy_to_fifo(void __iomem *fifo, const void *buf, int len) --{ -- unsigned long tmp; -- -- DBG(DBG_FIFO, "copy to FIFO (len %d):\n", len); -- for (; len > 0; len -= 4, buf += 4, fifo += 4) { -- tmp = *(unsigned long *)buf; -- if (len >= 4) { -- DBG(DBG_FIFO, " -> %08lx\n", tmp); -- __raw_writel(tmp, fifo); -- } else { -- do { -- DBG(DBG_FIFO, " -> %02lx\n", tmp >> 24); -- __raw_writeb(tmp >> 24, fifo); -- fifo++; -- tmp <<= 8; -- } while (--len); -- break; -- } -- } --} -- --static void copy_from_fifo(void *buf, void __iomem *fifo, int len) --{ -- union { -- unsigned long *w; -- unsigned char *b; -- } p; -- unsigned long tmp; -- -- DBG(DBG_FIFO, "copy from FIFO (len %d):\n", len); -- for (p.w = buf; len > 0; len -= 4, p.w++, fifo += 4) { -- if (len >= 4) { -- tmp = __raw_readl(fifo); -- *p.w = tmp; -- DBG(DBG_FIFO, " -> %08lx\n", tmp); -- } else { -- do { -- tmp = __raw_readb(fifo); -- *p.b = tmp; -- DBG(DBG_FIFO, " -> %02lx\n", tmp); -- fifo++, p.b++; -- } while (--len); -- } -- } --} -- - static void next_fifo_transaction(struct usba_ep *ep, struct usba_request *req) - { - unsigned int transaction_len; -@@ -387,7 +342,7 @@ static void next_fifo_transaction(struct - ep->ep.name, req, transaction_len, - req->last_transaction ? ", done" : ""); - -- copy_to_fifo(ep->fifo, req->req.buf + req->req.actual, transaction_len); -+ memcpy_toio(ep->fifo, req->req.buf + req->req.actual, transaction_len); - usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY); - req->req.actual += transaction_len; - } -@@ -476,7 +431,7 @@ static void receive_data(struct usba_ep - bytecount = req->req.length - req->req.actual; - } - -- copy_from_fifo(req->req.buf + req->req.actual, -+ memcpy_fromio(req->req.buf + req->req.actual, - ep->fifo, bytecount); - req->req.actual += bytecount; - -@@ -1029,33 +984,6 @@ static const struct usb_gadget_ops usba_ - .set_selfpowered = usba_udc_set_selfpowered, - }; - --#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \ --{ \ -- .ep = { \ -- .ops = &usba_ep_ops, \ -- .name = nam, \ -- .maxpacket = maxpkt, \ -- }, \ -- .udc = &the_udc, \ -- .queue = LIST_HEAD_INIT(usba_ep[idx].queue), \ -- .fifo_size = maxpkt, \ -- .nr_banks = maxbk, \ -- .index = idx, \ -- .can_dma = dma, \ -- .can_isoc = isoc, \ --} -- --static struct usba_ep usba_ep[] = { -- EP("ep0", 0, 64, 1, 0, 0), -- EP("ep1in-bulk", 1, 512, 2, 1, 1), -- EP("ep2out-bulk", 2, 512, 2, 1, 1), -- EP("ep3in-int", 3, 64, 3, 1, 0), -- EP("ep4out-int", 4, 64, 3, 1, 0), -- EP("ep5in-iso", 5, 1024, 3, 1, 1), -- EP("ep6out-iso", 6, 1024, 3, 1, 1), --}; --#undef EP -- - static struct usb_endpoint_descriptor usba_ep0_desc = { - .bLength = USB_DT_ENDPOINT_SIZE, - .bDescriptorType = USB_DT_ENDPOINT, -@@ -1074,7 +1002,6 @@ static void nop_release(struct device *d - static struct usba_udc the_udc = { - .gadget = { - .ops = &usba_udc_ops, -- .ep0 = &usba_ep[0].ep, - .ep_list = LIST_HEAD_INIT(the_udc.gadget.ep_list), - .is_dualspeed = 1, - .name = "atmel_usba_udc", -@@ -1231,7 +1158,7 @@ static int do_test_mode(struct usba_udc - } else { - usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE); - usba_writel(udc, TST, USBA_TST_PKT_MODE); -- copy_to_fifo(ep->fifo, test_packet_buffer, -+ memcpy_toio(ep->fifo, test_packet_buffer, - sizeof(test_packet_buffer)); - usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY); - dev_info(dev, "Entering Test_Packet mode...\n"); -@@ -1530,13 +1457,13 @@ restart: - DBG(DBG_HW, "Packet length: %u\n", pkt_len); - if (pkt_len != sizeof(crq)) { - pr_warning("udc: Invalid packet length %u " -- "(expected %lu)\n", pkt_len, sizeof(crq)); -+ "(expected %zu)\n", pkt_len, sizeof(crq)); - set_protocol_stall(udc, ep); - return; - } - - DBG(DBG_FIFO, "Copying ctrl request from 0x%p:\n", ep->fifo); -- copy_from_fifo(crq.data, ep->fifo, sizeof(crq)); -+ memcpy_fromio(crq.data, ep->fifo, sizeof(crq)); - - /* Free up one bank in the FIFO so that we can - * generate or receive a reply right away. */ -@@ -1908,7 +1835,7 @@ static int __init usba_udc_probe(struct - - regs = platform_get_resource(pdev, IORESOURCE_MEM, CTRL_IOMEM_ID); - fifo = platform_get_resource(pdev, IORESOURCE_MEM, FIFO_IOMEM_ID); -- if (!regs || !fifo) -+ if (!regs || !fifo || !pdata) - return -ENXIO; - - irq = platform_get_irq(pdev, 0); -@@ -1956,16 +1883,44 @@ static int __init usba_udc_probe(struct - usba_writel(udc, CTRL, 0); - clk_disable(pclk); - -+ usba_ep = kmalloc(sizeof(struct usba_ep) * pdata->num_ep, -+ GFP_KERNEL); -+ if (!usba_ep) -+ goto err_alloc_ep; -+ -+ the_udc.gadget.ep0 = &usba_ep[0].ep; -+ - INIT_LIST_HEAD(&usba_ep[0].ep.ep_list); - usba_ep[0].ep_regs = udc->regs + USBA_EPT_BASE(0); - usba_ep[0].dma_regs = udc->regs + USBA_DMA_BASE(0); - usba_ep[0].fifo = udc->fifo + USBA_FIFO_BASE(0); -- for (i = 1; i < ARRAY_SIZE(usba_ep); i++) { -+ usba_ep[0].ep.ops = &usba_ep_ops; -+ usba_ep[0].ep.name = pdata->ep[0].name; -+ usba_ep[0].ep.maxpacket = pdata->ep[0].fifo_size; -+ usba_ep[0].udc = &the_udc; -+ INIT_LIST_HEAD(&usba_ep[0].queue); -+ usba_ep[0].fifo_size = pdata->ep[0].fifo_size; -+ usba_ep[0].nr_banks = pdata->ep[0].nr_banks; -+ usba_ep[0].index = pdata->ep[0].index; -+ usba_ep[0].can_dma = pdata->ep[0].can_dma; -+ usba_ep[0].can_isoc = pdata->ep[0].can_isoc; -+ -+ for (i = 1; i < pdata->num_ep; i++) { - struct usba_ep *ep = &usba_ep[i]; - - ep->ep_regs = udc->regs + USBA_EPT_BASE(i); - ep->dma_regs = udc->regs + USBA_DMA_BASE(i); - ep->fifo = udc->fifo + USBA_FIFO_BASE(i); -+ ep->ep.ops = &usba_ep_ops; -+ ep->ep.name = pdata->ep[i].name; -+ ep->ep.maxpacket = pdata->ep[i].fifo_size; -+ ep->udc = &the_udc; -+ INIT_LIST_HEAD(&ep->queue); -+ ep->fifo_size = pdata->ep[i].fifo_size; -+ ep->nr_banks = pdata->ep[i].nr_banks; -+ ep->index = pdata->ep[i].index; -+ ep->can_dma = pdata->ep[i].can_dma; -+ ep->can_isoc = pdata->ep[i].can_isoc; - - list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list); - } -@@ -1984,7 +1939,7 @@ static int __init usba_udc_probe(struct - goto err_device_add; - } - -- if (pdata && pdata->vbus_pin != GPIO_PIN_NONE) { -+ if (pdata->vbus_pin >= 0) { - if (!gpio_request(pdata->vbus_pin, "atmel_usba_udc")) { - udc->vbus_pin = pdata->vbus_pin; - -@@ -2004,7 +1959,7 @@ static int __init usba_udc_probe(struct - } - - usba_init_debugfs(udc); -- for (i = 1; i < ARRAY_SIZE(usba_ep); i++) -+ for (i = 1; i < pdata->num_ep; i++) - usba_ep_init_debugfs(udc, &usba_ep[i]); - - return 0; -@@ -2012,6 +1967,8 @@ static int __init usba_udc_probe(struct - err_device_add: - free_irq(irq, udc); - err_request_irq: -+ kfree(usba_ep); -+err_alloc_ep: - iounmap(udc->fifo); - err_map_fifo: - iounmap(udc->regs); -@@ -2029,10 +1986,11 @@ static int __exit usba_udc_remove(struct - { - struct usba_udc *udc; - int i; -+ struct usba_platform_data *pdata = pdev->dev.platform_data; - - udc = platform_get_drvdata(pdev); - -- for (i = 1; i < ARRAY_SIZE(usba_ep); i++) -+ for (i = 1; i < pdata->num_ep; i++) - usba_ep_cleanup_debugfs(&usba_ep[i]); - usba_cleanup_debugfs(udc); - ---- a/drivers/usb/host/ohci-at91.c -+++ b/drivers/usb/host/ohci-at91.c -@@ -330,7 +330,7 @@ ohci_hcd_at91_drv_suspend(struct platfor - * - * REVISIT: some boards will be able to turn VBUS off... - */ -- if (at91_suspend_entering_slow_clock()) { -+ if (clk_must_disable(fclk)) { - ohci_usb_reset (ohci); - at91_stop_clock(); - } ---- a/drivers/video/Kconfig -+++ b/drivers/video/Kconfig -@@ -889,6 +889,17 @@ config FB_EPSON1355 - framebuffer. Product specs at - <http://www.erd.epson.com/vdc/html/products.htm>. - -+config FB_S1D15605 -+ tristate "Epson S1D15605 framebuffer support" -+ depends on FB -+ default m if MACH_KB9200 -+ select FB_CFB_FILLRECT -+ select FB_CFB_COPYAREA -+ select FB_CFB_IMAGEBLIT -+ help -+ Build in support for the S1D15605 Epson Research 128x64 -+ LCD controller as a framebuffer. -+ - config FB_S1D13XXX - tristate "Epson S1D13XXX framebuffer support" - depends on FB ---- a/drivers/video/Makefile -+++ b/drivers/video/Makefile -@@ -87,7 +87,8 @@ obj-$(CONFIG_FB_G364) += g36 - obj-$(CONFIG_FB_SA1100) += sa1100fb.o - obj-$(CONFIG_FB_HIT) += hitfb.o - obj-$(CONFIG_FB_EPSON1355) += epson1355fb.o --obj-$(CONFIG_FB_ATMEL) += atmel_lcdfb.o -+obj-$(CONFIG_FB_S1D15605) += s1d15605fb.o -+obj-$(CONFIG_FB_ATMEL) += atmel_lcdfb.o - obj-$(CONFIG_FB_PVR2) += pvr2fb.o - obj-$(CONFIG_FB_VOODOO1) += sstfb.o - obj-$(CONFIG_FB_ARMCLCD) += amba-clcd.o ---- a/drivers/video/atmel_lcdfb.c -+++ b/drivers/video/atmel_lcdfb.c -@@ -31,7 +31,7 @@ - #define ATMEL_LCDC_CVAL_DEFAULT 0xc8 - #define ATMEL_LCDC_DMA_BURST_LEN 8 - --#if defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9) -+#if defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9) || defined(CONFIG_ARCH_AT91SAM9RL) - #define ATMEL_LCDC_FIFO_SIZE 2048 - #else - #define ATMEL_LCDC_FIFO_SIZE 512 -@@ -903,11 +903,45 @@ static int __exit atmel_lcdfb_remove(str - return 0; - } - --static struct platform_driver atmel_lcdfb_driver = { -- .remove = __exit_p(atmel_lcdfb_remove), -+#ifdef CONFIG_PM -+ -+static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg) -+{ -+ struct fb_info *info = platform_get_drvdata(pdev); -+ struct atmel_lcdfb_info *sinfo = info->par; -+ -+ sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_VAL); -+ lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0); -+ if (sinfo->atmel_lcdfb_power_control) -+ sinfo->atmel_lcdfb_power_control(0); -+ atmel_lcdfb_stop_clock(sinfo); - --// FIXME need suspend, resume -+ return 0; -+} -+ -+static int atmel_lcdfb_resume(struct platform_device *pdev) -+{ -+ struct fb_info *info = platform_get_drvdata(pdev); -+ struct atmel_lcdfb_info *sinfo = info->par; - -+ atmel_lcdfb_start_clock(sinfo); -+ if (sinfo->atmel_lcdfb_power_control) -+ sinfo->atmel_lcdfb_power_control(1); -+ lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon); -+ -+ return 0; -+} -+ -+#else -+#define atmel_lcdfb_suspend NULL -+#define atmel_lcdfb_resume NULL -+#endif -+ -+ -+static struct platform_driver atmel_lcdfb_driver = { -+ .remove = __exit_p(atmel_lcdfb_remove), -+ .suspend = atmel_lcdfb_suspend, -+ .resume = atmel_lcdfb_resume, - .driver = { - .name = "atmel_lcdfb", - .owner = THIS_MODULE, ---- a/drivers/video/backlight/Kconfig -+++ b/drivers/video/backlight/Kconfig -@@ -112,3 +112,11 @@ config BACKLIGHT_CARILLO_RANCH - help - If you have a Intel LE80578 (Carillo Ranch) say Y to enable the - backlight driver. -+ -+config BACKLIGHT_KB920x -+ tristate "KwikByte KB9202 Backlight Driver" -+ depends on BACKLIGHT_CLASS_DEVICE && MACH_KB9200 -+ default y -+ help -+ If you have a KwikByte KB9202 board, say Y to enable the -+ backlight driver. ---- a/drivers/video/backlight/Makefile -+++ b/drivers/video/backlight/Makefile -@@ -10,3 +10,4 @@ obj-$(CONFIG_BACKLIGHT_LOCOMO) += locomo - obj-$(CONFIG_BACKLIGHT_OMAP1) += omap1_bl.o - obj-$(CONFIG_BACKLIGHT_PROGEAR) += progear_bl.o - obj-$(CONFIG_BACKLIGHT_CARILLO_RANCH) += cr_bllcd.o -+obj-$(CONFIG_BACKLIGHT_KB920x) += kb920x_bl.o ---- /dev/null -+++ b/drivers/video/backlight/kb920x_bl.c -@@ -0,0 +1,164 @@ -+/* -+ * Backlight Driver for KB9202 -+ * -+ * Copyright (c) 2006 KwikByte -+ * -+ * Based on Sharp's Corgi Backlight Driver -+ * -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ */ -+ -+#include <linux/module.h> -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+#include <linux/spinlock.h> -+#include <linux/fb.h> -+#include <linux/backlight.h> -+ -+#include <asm/arch/gpio.h> -+ -+/* The backlight is on(1)/off(0) */ -+#define KB9202_DEFAULT_INTENSITY 1 -+#define KB9202_MAX_INTENSITY 1 -+ -+static int kb9202bl_suspended; -+static int current_intensity = 0; -+static DEFINE_SPINLOCK(bl_lock); -+ -+static int kb9202bl_set_intensity(struct backlight_device *bd) -+{ -+ unsigned long flags; -+ int intensity = bd->props.brightness; -+ -+ if (bd->props.power != FB_BLANK_UNBLANK) -+ intensity = 0; -+ if (bd->props.fb_blank != FB_BLANK_UNBLANK) -+ intensity = 0; -+ if (kb9202bl_suspended) -+ intensity = 0; -+ -+ if ((!current_intensity) && (bd->props.power == FB_BLANK_UNBLANK)) -+ intensity = 1; -+ -+ spin_lock_irqsave(&bl_lock, flags); -+ if (intensity) -+ gpio_set_value(AT91_PIN_PC23, 1); -+ else -+ gpio_set_value(AT91_PIN_PC23, 0); -+ spin_unlock_irqrestore(&bl_lock, flags); -+ -+ current_intensity = intensity; -+ -+ return 0; -+} -+ -+static int kb9202bl_get_intensity(struct backlight_device *bd) -+{ -+ return current_intensity; -+} -+ -+static struct backlight_ops kb9202bl_ops = { -+ .get_brightness = kb9202bl_get_intensity, -+ .update_status = kb9202bl_set_intensity, -+}; -+ -+static int __init kb9202bl_probe(struct platform_device *pdev) -+{ -+ struct backlight_device *bd; -+ -+ bd = backlight_device_register ("kb9202-bl", &pdev->dev, NULL, &kb9202bl_ops); -+ if (IS_ERR(bd)) -+ return PTR_ERR(bd); -+ -+ platform_set_drvdata(pdev, bd); -+ -+ bd->props.max_brightness = KB9202_MAX_INTENSITY; -+ bd->props.brightness = KB9202_DEFAULT_INTENSITY; -+ (void) kb9202bl_set_intensity(bd); -+ -+ return 0; -+} -+ -+static int kb9202bl_remove(struct platform_device *pdev) -+{ -+ struct backlight_device *bd = platform_get_drvdata(pdev); -+ -+ bd->props.brightness = 0; -+ bd->props.power = 0; -+ (void) kb9202bl_set_intensity(bd); -+ -+ backlight_device_unregister(bd); -+ -+ return 0; -+} -+ -+#ifdef CONFIG_PM -+static int kb9202bl_suspend(struct platform_device *pdev, pm_message_t state) -+{ -+ struct backlight_device *bd = platform_get_drvdata(pdev); -+ -+ kb9202bl_suspended = 1; -+ (void) kb9202bl_set_intensity(bd); -+ return 0; -+} -+ -+static int kb9202bl_resume(struct platform_device *pdev) -+{ -+ struct backlight_device *bd = platform_get_drvdata(pdev); -+ -+ kb9202bl_suspended = 0; -+ (void) kb9202bl_set_intensity(bd); -+ return 0; -+} -+#else -+#define kb9202bl_suspend NULL -+#define kb9202bl_resume NULL -+#endif -+ -+static struct platform_driver kb9202bl_driver = { -+ .probe = kb9202bl_probe, -+ .remove = kb9202bl_remove, -+ .suspend = kb9202bl_suspend, -+ .resume = kb9202bl_resume, -+ .driver = { -+ .name = "kb9202-bl", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+static struct platform_device *kb9202bl_device; -+ -+static int __init kb9202bl_init(void) -+{ -+ int ret; -+ -+ ret = platform_driver_register(&kb9202bl_driver); -+ if (!ret) { -+ kb9202bl_device = platform_device_alloc("kb9202-bl", -1); -+ if (!kb9202bl_device) -+ return -ENOMEM; -+ -+ ret = platform_device_add(kb9202bl_device); -+ if (ret) { -+ platform_device_put(kb9202bl_device); -+ platform_driver_unregister(&kb9202bl_driver); -+ } -+ } -+ return ret; -+} -+ -+static void __exit kb9202bl_exit(void) -+{ -+ platform_device_unregister(kb9202bl_device); -+ platform_driver_unregister(&kb9202bl_driver); -+} -+ -+module_init(kb9202bl_init); -+module_exit(kb9202bl_exit); -+ -+MODULE_AUTHOR("KwikByte <kb9200_dev@kwikbyte.com>"); -+MODULE_DESCRIPTION("KB9202 Backlight Driver"); -+MODULE_LICENSE("GPL"); ---- /dev/null -+++ b/drivers/video/s1d15605fb.c -@@ -0,0 +1,655 @@ -+/* -+ * drivers/video/s1d15605.c -+ * -+ * Adapted from several sources including: -+ * 1) Driver for AT91 LCD Controller -+ * Copyright (C) 2006 Atmel -+ * -+ * 2) Copyright (C) 2005 S. Kevin Hester -+ * -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file COPYING in the main directory of this archive for -+ * more details. -+ * -+ * This is a basic framebuffer driver for the Optrex F-51320 128x64 mono LCD -+ * display. This display uses a clone of the common Epson SED 1531 display -+ * controller. -+ * -+ * I've heavily borrowed code from the vfb.c driver. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#ifdef DEBUG -+#define MSG(string, args...) printk("s1d15605fb:" string, ##args) -+#else -+#define MSG(string, args...) -+#endif -+ -+#include <linux/kernel.h> -+#include <linux/platform_device.h> -+#include <linux/dma-mapping.h> -+#include <linux/interrupt.h> -+#include <linux/clk.h> -+#include <linux/fb.h> -+#include <linux/init.h> -+#include <linux/delay.h> -+ -+#include <asm/uaccess.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+ -+#ifdef CONFIG_PMAC_BACKLIGHT -+#include <asm/backlight.h> -+#endif -+ -+#define VIDEOWIDTH 128 -+#define VIDEOHEIGHT 64 -+#define VIDEODEPTH 1 /* bits/pixel */ -+#define VIDEOWIDTH_BYTES ((VIDEOWIDTH * VIDEODEPTH) / 8) -+ -+/* The number of bytes that actually go to the device */ -+#define ACTUALVIDEOMEMSIZE (VIDEOWIDTH_BYTES * VIDEOHEIGHT) -+#define VIDEOMEMSIZE PAGE_SIZE -+ -+static struct fb_var_screeninfo s1d15605_default __initdata = { -+ .xres = VIDEOWIDTH, -+ .yres = VIDEOHEIGHT, -+ .xres_virtual = VIDEOWIDTH, -+ .yres_virtual = VIDEOHEIGHT, -+ .bits_per_pixel = VIDEODEPTH, -+ .red = { 0, 1, 0 }, -+ .green = { 0, 1, 0 }, -+ .blue = { 0, 1, 0 }, -+ .activate = FB_ACTIVATE_NOW, -+ .pixclock = 20000, -+ .vmode = FB_VMODE_NONINTERLACED, -+}; -+ -+static struct fb_fix_screeninfo s1d15605_fix __initdata = { -+ .id = "s1d15605", -+ .type = FB_TYPE_PACKED_PIXELS, -+ .visual = FB_VISUAL_MONO10, -+ .xpanstep = 0, -+ .ypanstep = 0, -+ .ywrapstep = 0, -+ .accel = FB_ACCEL_NONE, -+}; -+ -+struct s1d15605fb_info { -+ struct fb_info *info; -+ char *mmio; -+ unsigned long reset_pin; -+ struct platform_device *pdev; -+}; -+ -+/* -+ * LCD device interface -+ */ -+#define RESET_DISPLAY 0xE2 -+#define LCD_BIAS_1_9 0xA2 -+#define ADC_SELECT_REVERSE 0xA1 -+#define COMMON_OUTPUT_NORMAL 0xC0 -+#define V5_RESISTOR_RATIO 0x26 -+#define ELECTRONIC_VOLUME_SET 0x81 -+#define ELECTRONIC_VOLUME_INIT 0x20 -+#define POWER_CONTROL_SET 0x28 -+#define VOLTAGE_REGULATOR 0x02 -+#define VOLTAGE_FOLLOWER 0x01 -+#define BOOSTER_CIRCUIT 0x04 -+#define DISPLAY_ON 0xAF -+#define START_LINE_SET 0x40 -+#define PAGE_ADDRESS_SET 0xB0 -+#define COLUMN_ADDRESS_HIGH 0x10 -+#define COLUMN_ADDRESS_LOW 0x00 -+#define RESISTOR_RATIO_START 0x20 -+ -+#define NUM_OF_PAGES 8 -+#define NUM_OF_COLUMNS 128 -+ -+#define WRITE_COMMAND(x) __raw_writeb((x), (sinfo)->mmio) -+#define READ_COMMAND __raw_readb((sinfo)->mmio) -+#define WRITE_DATA(x) __raw_writeb((x), (sinfo)->mmio + (0x10000)) -+#define READ_DATA __raw_readb((sinfo)->mmio + (0x10000)) -+ -+ -+/* -+ * s1d15605fb_resize_framebuffer -+ * -+ * Free allocated space if different. Allocate on new of changed. -+ * Returns -ENOMEM if the new framebuffer can not be allocated, -+ * zero on success. -+ */ -+static int s1d15605fb_resize_framebuffer(struct s1d15605fb_info *sinfo) -+{ -+ struct fb_info *info = sinfo->info; -+ struct fb_fix_screeninfo *fix = &info->fix; -+ struct fb_var_screeninfo *var = &info->var; -+ unsigned int new_size; -+ void *new_vaddr; -+ -+ new_size = ((var->xres_virtual * var->yres_virtual * var->bits_per_pixel) / 8); -+ -+ MSG("%s: x (%d) y (%d) bpp (%d): new size 0x%08x\n", __FUNCTION__, -+ var->xres_virtual, var->yres_virtual, var->bits_per_pixel, new_size); -+ -+ if (new_size == fix->smem_len) -+ return 0; -+ -+ if (fix->smem_len) { -+ kfree(info->screen_base); -+ } -+ -+ new_vaddr = kmalloc(new_size, GFP_KERNEL); -+ -+ if (!new_vaddr) { -+ fix->smem_len = 0; -+ return -ENOMEM; -+ } -+ -+ info->screen_base = new_vaddr; -+ fix->smem_start = (unsigned)new_vaddr; -+ fix->smem_len = new_size; -+ fix->line_length = (var->xres_virtual * var->bits_per_pixel) / 8; -+ -+ dev_info(info->device, -+ "%luKiB frame buffer at %08lx (mapped at %p)\n", -+ (unsigned long)info->fix.smem_len / 1024, -+ (unsigned long)info->fix.smem_start, -+ info->screen_base); -+ -+ return 0; -+} -+ -+ -+/* -+ * The s1d15605 seems to be divided into eight 128 pixel wide pages (from top to -+ * bottom) each page seems to be eight pixels high, where these eight pixels are -+ * one byte -+ */ -+static void s1d15605_update(struct fb_info *info) -+{ -+ struct s1d15605fb_info *sinfo = info->par; -+ int page, i, row, colmask; -+ u8 retVal, *rowPtr; -+ -+ WRITE_COMMAND(START_LINE_SET); -+ for (page = 0; page < NUM_OF_PAGES; ++page) { -+ WRITE_COMMAND(PAGE_ADDRESS_SET + page); -+ WRITE_COMMAND(COLUMN_ADDRESS_HIGH); -+ WRITE_COMMAND(COLUMN_ADDRESS_LOW); -+ -+ for (i = 0; i < NUM_OF_COLUMNS; ++i) -+ { -+ /* point of opportunity: optimization */ -+ colmask = (1 << (i & 0x7)); -+ rowPtr = (u8*)(info->screen_base); -+ rowPtr += (VIDEOWIDTH_BYTES * 8 * page); -+ rowPtr += (i >> 3); -+ retVal = 0; -+ for (row = 0; row < 8; ++row) -+ { -+ retVal = (retVal >> 1) | (((*rowPtr) & colmask) ? 0x80 : 0); -+ rowPtr += VIDEOWIDTH_BYTES; -+ } -+ WRITE_DATA(retVal); -+ } -+ } -+ -+ WRITE_COMMAND(DISPLAY_ON); -+} -+ -+ -+/* -+ * Setting the video mode has been split into two parts. -+ * First part, xxxfb_check_var, must not write anything -+ * to hardware, it should only verify and adjust var. -+ * This means it doesn't alter par but it does use hardware -+ * data from it to check this var. -+ */ -+static int s1d15605_check_var(struct fb_var_screeninfo *var, struct fb_info *info) -+{ -+ /* -+ * Some very basic checks -+ */ -+ if (!var->xres) -+ var->xres = 1; -+ if (!var->yres) -+ var->yres = 1; -+ if (var->xres > var->xres_virtual) -+ var->xres_virtual = var->xres; -+ if (var->yres > var->yres_virtual) -+ var->yres_virtual = var->yres; -+ -+ if(var->bits_per_pixel > VIDEODEPTH) -+ return -EINVAL; -+ -+ /* -+ * Memory limit -+ */ -+ if (((var->yres_virtual * var->bits_per_pixel * var->yres_virtual) >> 3) > -+ ACTUALVIDEOMEMSIZE) -+ return -ENOMEM; -+ -+ /* -+ * Now that we checked it we alter var. The reason being is that the video -+ * mode passed in might not work but slight changes to it might make it -+ * work. This way we let the user know what is acceptable. -+ */ -+ switch (var->bits_per_pixel) { -+ case 1: -+ var->red.offset = var->green.offset = var->blue.offset = 0; -+ var->red.length = var->green.length = var->blue.length -+ = var->bits_per_pixel; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ var->xoffset = var->yoffset = 0; -+ var->red.msb_right = var->green.msb_right = var->blue.msb_right = -+ var->transp.msb_right = 0; -+ -+ return 0; -+} -+ -+ -+/* -+ * This routine actually sets the video mode. It's in here where we -+ * the hardware state info->par and fix which can be affected by the -+ * change in par. For this driver it doesn't do much. -+ */ -+static int s1d15605_set_par(struct fb_info *info) -+{ -+ int ret; -+ -+ MSG("%s:\n", __func__); -+ MSG(" * resolution: %ux%u (%ux%u virtual)\n", -+ info->var.xres, info->var.yres, -+ info->var.xres_virtual, info->var.yres_virtual); -+ -+ ret = s1d15605fb_resize_framebuffer(info->par); -+ -+ info->fix.visual = FB_VISUAL_MONO10; -+ return ret; -+} -+ -+ -+/* -+ * Set a single color register. The values supplied are already -+ * rounded down to the hardware's capabilities (according to the -+ * entries in the var structure). Return != 0 for invalid regno. -+ */ -+static int s1d15605_setcolreg(u_int regno, u_int red, u_int green, u_int blue, -+ u_int transp, struct fb_info *info) -+{ -+ if (regno > 1) /* no. of hw registers - we only do mono now */ -+ return 1; -+ -+ return 0; -+} -+ -+ -+/* -+ * Currently, the routine will simply shut-off the backlight and prevent -+ * updates/refreshes. Modify according to application. -+ * -+ * 0 unblank, 1 blank, 2 no vsync, 3 no hsync, 4 off -+ */ -+static int s1d15605_blank(int blank, struct fb_info *info) -+{ -+#ifdef CONFIG_PMAC_BACKLIGHT -+ if (blank) -+ pmac_backlight->props.power = FB_BLANK_POWERDOWN; -+ else -+ pmac_backlight->props.power = FB_BLANK_UNBLANK; -+ backlight_update_status(pmac_backlight); -+#endif -+ return 1; -+} -+ -+ -+/* -+ * Pan or Wrap the Display -+ * -+ * This call looks only at xoffset, yoffset and the FB_VMODE_YWRAP flag -+ */ -+/* -+static int s1d15605_pan_display(struct fb_var_screeninfo *var, -+ struct fb_info *info) -+{ -+ if (var->vmode & FB_VMODE_YWRAP) { -+ if (var->yoffset < 0 -+ || var->yoffset >= info->var.yres_virtual -+ || var->xoffset) -+ return -EINVAL; -+ } else { -+ if (var->xoffset + var->xres > info->var.xres_virtual || -+ var->yoffset + var->yres > info->var.yres_virtual) -+ return -EINVAL; -+ } -+ info->var.xoffset = var->xoffset; -+ info->var.yoffset = var->yoffset; -+ if (var->vmode & FB_VMODE_YWRAP) -+ info->var.vmode |= FB_VMODE_YWRAP; -+ else -+ info->var.vmode &= ~FB_VMODE_YWRAP; -+ return 0; -+} -+*/ -+ -+ -+static void s1d15605_copyarea(struct fb_info *info, const struct fb_copyarea *region) -+{ -+ cfb_copyarea(info, region); -+ s1d15605_update(info); -+} -+ -+ -+static void s1d15605_fillrect (struct fb_info *info, const struct fb_fillrect *rect) -+{ -+ cfb_fillrect(info, rect); -+ s1d15605_update(info); -+} -+ -+ -+static void s1d15605_imageblit(struct fb_info *p, const struct fb_image *image) -+{ -+ cfb_imageblit(p, image); -+ s1d15605_update(p); -+} -+ -+ -+/* -+ * Write the users data to our framebuffer, and then trigger a psuedo DMA -+ */ -+static ssize_t s1d15605_write(struct fb_info *info, const char *buf, -+ size_t count, loff_t *ppos) -+{ -+ unsigned long p = *ppos; -+ int err; -+ -+ if (p > info->fix.smem_len) -+ return -ENOSPC; -+ if (count >= info->fix.smem_len) -+ count = info->fix.smem_len; -+ err = 0; -+ if (count + p > info->fix.smem_len) { -+ count = info->fix.smem_len - p; -+ err = -ENOSPC; -+ } -+ if (count) { -+ char *base_addr; -+ -+ base_addr = info->screen_base; -+ count -= copy_from_user(base_addr+p, buf, count); -+ *ppos += count; -+ err = -EFAULT; -+ } -+ -+ s1d15605_update(info); -+ -+ if (count) -+ return count; -+ -+ return err; -+} -+ -+#ifdef USE_PRIVATE_VMA_FXS -+static void s1d15605_vma_open(struct vm_area_struct *vma) -+{ -+ // FIXME - store stats in the device data via vm_private_data -+} -+ -+ -+static void s1d15605_vma_close(struct vm_area_struct *vma) -+{ -+ // FIXME - store stats in the device data via vm_private_data -+} -+ -+ -+static struct page *s1d15605_vma_nopage(struct vm_area_struct *vma, -+ unsigned long address, int *type) -+{ -+ struct page *page; -+ struct fb_info *info = vma->vm_private_data; -+ -+ page = virt_to_page(info->screen_base); -+ get_page(page); -+ -+ // FIXME - now someone has a link to our page, start periodically blitting -+ // latest updates to the actual device. -+ -+ return page; -+} -+ -+ -+static struct vm_operations_struct s1d15605_vm_ops = { -+ .open = s1d15605_vma_open, -+ .close = s1d15605_vma_close, -+ .nopage = s1d15605_vma_nopage -+}; -+ -+ -+/* We don't do much here - because we have special vm_ops */ -+static int s1d15605_mmap(struct fb_info *info, struct vm_area_struct *vma) -+{ -+ vma->vm_ops = &s1d15605_vm_ops; -+ vma->vm_flags |= VM_RESERVED; -+ vma->vm_private_data = info; -+ s1d15605_vma_open(vma); -+ -+ return 0; -+} -+#endif /* USE_PRIVATE_VMA_FXS */ -+ -+ -+static struct fb_ops s1d15605fb_ops = { -+ .owner = THIS_MODULE, -+ .fb_check_var = s1d15605_check_var, -+ .fb_set_par = s1d15605_set_par, -+ .fb_setcolreg = s1d15605_setcolreg, -+ .fb_blank = s1d15605_blank, -+// .fb_pan_display = s1d15605_pan_display, -+ .fb_fillrect = s1d15605_fillrect, -+ .fb_copyarea = s1d15605_copyarea, -+ .fb_imageblit = s1d15605_imageblit, -+ .fb_write = s1d15605_write, -+#ifdef USE_PRIVATE_VMA_FXS -+ .fb_mmap = s1d15605_mmap, -+#endif -+}; -+ -+ -+static void s1d15605_device_init(struct s1d15605fb_info *sinfo) { -+ -+ char value; -+ -+ /* release the reset line by reading the device - proto hardware */ -+ value = READ_COMMAND; -+ value = READ_COMMAND; -+ -+#ifdef CONFIG_MACH_KB9200 -+ /* new boards have dedicated reset line */ -+ gpio_set_value(sinfo->reset_pin, 1); -+#endif -+ -+ /* initialize the device within 5ms */ -+ WRITE_COMMAND(RESET_DISPLAY); -+ WRITE_COMMAND(LCD_BIAS_1_9); -+ WRITE_COMMAND(ADC_SELECT_REVERSE); -+ WRITE_COMMAND(COMMON_OUTPUT_NORMAL); -+ WRITE_COMMAND(V5_RESISTOR_RATIO); -+ WRITE_COMMAND(ELECTRONIC_VOLUME_SET); -+ WRITE_COMMAND(ELECTRONIC_VOLUME_INIT); -+ WRITE_COMMAND(POWER_CONTROL_SET | VOLTAGE_REGULATOR | VOLTAGE_FOLLOWER | BOOSTER_CIRCUIT); -+ WRITE_COMMAND(DISPLAY_ON); -+ -+ WRITE_COMMAND(RESISTOR_RATIO_START + 4); -+ WRITE_COMMAND(ELECTRONIC_VOLUME_SET); -+ WRITE_COMMAND(0x33); -+} -+ -+ -+static int __init s1d15605fb_probe(struct platform_device *pdev) -+{ -+ struct device *dev = &pdev->dev; -+ struct fb_info *info; -+ struct s1d15605fb_info *sinfo; -+ int ret; -+ -+ MSG("%s\n", __func__); -+ -+ if (!(info = framebuffer_alloc(sizeof(struct s1d15605fb_info), dev))) { -+ dev_err(dev, "Cannot allocate framebuffer struct\n"); -+ return -ENOMEM; -+ } -+ -+ sinfo = info->par; -+ sinfo->info = info; -+ sinfo->pdev = pdev; -+ -+ if (pdev->num_resources < 2) { -+ dev_err(dev, "Resources unusable\n"); -+ ret = -ENODEV; -+ goto free_info; -+ } -+ -+ info->fbops = &s1d15605fb_ops; -+ strcpy(info->fix.id, pdev->name); -+ -+ info->fix.mmio_start = pdev->resource[0].start; -+ info->fix.mmio_len = pdev->resource[0].end - pdev->resource[0].start + 1; -+ sinfo->reset_pin = pdev->resource[1].start; -+ -+ ret = s1d15605fb_resize_framebuffer(sinfo); -+ if (ret < 0) { -+ dev_err(dev, "Cannot resize framebuffer: %d\n", ret); -+ goto free_fb; -+ } -+ -+ if (!request_mem_region(info->fix.mmio_start, -+ info->fix.mmio_len, pdev->name)) { -+ ret = -EBUSY; -+ goto free_fb; -+ } -+ -+ sinfo->mmio = ioremap(info->fix.mmio_start, info->fix.mmio_len); -+ if (!sinfo->mmio) { -+ dev_err(dev, "Cannot map LCD memory region\n"); -+ goto release_mem; -+ } -+ -+ s1d15605_device_init(sinfo); -+ -+ ret = fb_find_mode(&info->var, info, NULL, NULL, 0, NULL, 1); -+ -+ if (!ret || (ret == 4)) -+ info->var = s1d15605_default; -+ -+ info->fix = s1d15605_fix; -+ info->flags = FBINFO_FLAG_DEFAULT | -+/* FBINFO_HWACCEL_YPAN | */ -+ FBINFO_HWACCEL_FILLRECT | FBINFO_HWACCEL_COPYAREA; -+ -+ ret = register_framebuffer(info); -+ if (ret < 0) { -+ dev_err(dev, "Failed to register framebuffer device: %d\n", ret); -+ goto unmap_mmio; -+ } -+ -+ dev_set_drvdata(dev, info); -+ -+ memset(info->screen_base, 0, info->fix.smem_len); -+ info->var.activate |= FB_ACTIVATE_NOW; -+ ret = fb_set_var(info, &info->var); -+ if (ret) { -+ dev_warn(dev, "Unable to set display parameters\n"); -+ } -+ -+ info->var.activate &= ~(FB_ACTIVATE_FORCE | FB_ACTIVATE_NOW); -+ -+ dev_dbg(dev, "%s SUCCESS\n", __func__); -+ -+ dev_info(dev, "Driver $Revision: 1.1 $\n"); -+ -+ return 0; -+ -+unmap_mmio: -+ iounmap(sinfo->mmio); -+release_mem: -+ release_mem_region(info->fix.mmio_start, info->fix.mmio_len); -+free_fb: -+ kfree(info->screen_base); -+ -+free_info: -+ framebuffer_release(info); -+ -+ dev_dbg(dev, "%s FAILED\n", __func__); -+ return ret; -+} -+ -+ -+static int __exit s1d15605fb_remove(struct platform_device *pdev) -+{ -+ struct device *dev = &pdev->dev; -+ struct fb_info *info = dev_get_drvdata(dev); -+ struct s1d15605fb_info *sinfo = info->par; -+ -+ if (!sinfo) -+ return 0; -+ -+ unregister_framebuffer(info); -+ -+ iounmap(sinfo->mmio); -+ release_mem_region(info->fix.mmio_start, info->fix.mmio_len); -+ -+ kfree(info->screen_base); -+ -+ dev_set_drvdata(dev, NULL); -+ framebuffer_release(info); -+ return 0; -+} -+ -+ -+static struct platform_driver s1d15605fb_driver = { -+ .remove = __exit_p(s1d15605fb_remove), -+ .driver = { -+ .name = "s1d15605fb", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+ -+static int __init s1d15605fb_init(void) -+{ -+ return platform_driver_probe(&s1d15605fb_driver, s1d15605fb_probe); -+} -+ -+ -+static void __exit s1d15605fb_exit(void) -+{ -+ platform_driver_unregister(&s1d15605fb_driver); -+} -+ -+ -+module_init(s1d15605fb_init); -+module_exit(s1d15605fb_exit); -+ -+ -+MODULE_AUTHOR("KwikByte"); -+MODULE_DESCRIPTION("Epson S1D15605 LCD Controller framebuffer driver"); -+MODULE_LICENSE("GPL"); ---- a/drivers/watchdog/Kconfig -+++ b/drivers/watchdog/Kconfig -@@ -66,6 +66,14 @@ config AT91RM9200_WATCHDOG - Watchdog timer embedded into AT91RM9200 chips. This will reboot your - system when the timeout is reached. - -+config AT91SAM9_WATCHDOG -+ tristate "AT91SAM9 watchdog" -+ depends on ARCH_AT91 && !ARCH_AT91RM9200 -+ select WATCHDOG_NOWAYOUT -+ help -+ Watchdog timer embedded into AT91SAM9 chips. This will reboot your -+ system when the timeout is reached. -+ - config 21285_WATCHDOG - tristate "DC21285 watchdog" - depends on FOOTBRIDGE ---- a/drivers/watchdog/Makefile -+++ b/drivers/watchdog/Makefile -@@ -26,6 +26,7 @@ obj-$(CONFIG_USBPCWATCHDOG) += pcwd_usb. - - # ARM Architecture - obj-$(CONFIG_AT91RM9200_WATCHDOG) += at91rm9200_wdt.o -+obj-$(CONFIG_AT91SAM9_WATCHDOG) += at91sam9_wdt.o - obj-$(CONFIG_OMAP_WATCHDOG) += omap_wdt.o - obj-$(CONFIG_21285_WATCHDOG) += wdt285.o - obj-$(CONFIG_977_WATCHDOG) += wdt977.o ---- /dev/null -+++ b/drivers/watchdog/at91sam9_wdt.c -@@ -0,0 +1,259 @@ -+/* -+ * Watchdog driver for Atmel AT91SAM9x processors. -+ * -+ * Copyright (C) 2007 Renaud CERRATO r.cerrato@til-technologies.fr -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version -+ * 2 of the License, or (at your option) any later version. -+ */ -+ -+/* -+ * The Watchdog Timer Mode Register can be only written to once. If the -+ * timeout need to be set from Linux, be sure that the bootstrap or the -+ * bootloader doesn't write to this register. -+ */ -+ -+#include <linux/errno.h> -+#include <linux/fs.h> -+#include <linux/init.h> -+#include <linux/kernel.h> -+#include <linux/miscdevice.h> -+#include <linux/module.h> -+#include <linux/moduleparam.h> -+#include <linux/platform_device.h> -+#include <linux/types.h> -+#include <linux/watchdog.h> -+#include <linux/bitops.h> -+#include <linux/uaccess.h> -+ -+#include <asm/arch/at91_wdt.h> -+ -+ -+#define WDT_MAX_TIME 16 /* seconds */ -+ -+static int wdt_timeout = -1; /* invalid */ -+ -+module_param(wdt_timeout, int, 0); -+MODULE_PARM_DESC(wdt_timeout, "Watchdog time in seconds. (default = disabled)"); -+ -+ -+static unsigned long at91wdt_busy; -+ -+/* ......................................................................... */ -+ -+/* -+ * Reload the watchdog timer. (ie, pat the watchdog) -+ */ -+static void inline at91_wdt_reload(void) -+{ -+ at91_sys_write(AT91_WDT_CR, AT91_WDT_KEY | AT91_WDT_WDRSTT); -+} -+ -+/* ......................................................................... */ -+ -+/* -+ * Watchdog device is opened, and watchdog starts running. -+ */ -+static int at91_wdt_open(struct inode *inode, struct file *file) -+{ -+ if (test_and_set_bit(0, &at91wdt_busy)) -+ return -EBUSY; -+ -+ return nonseekable_open(inode, file); -+} -+ -+/* -+ * Close the watchdog device. -+ */ -+static int at91_wdt_close(struct inode *inode, struct file *file) -+{ -+ clear_bit(0, &at91wdt_busy); -+ return 0; -+} -+ -+/* -+ * Change the watchdog time interval. -+ */ -+static int at91_wdt_settimeout(int new_time) -+{ -+ unsigned int reg, mr; -+ /* -+ * All counting occurs at SLOW_CLOCK / 128 = 256 Hz -+ * -+ * Since WDV is a 12-bit counter, the maximum period is -+ * 4096 / 256 = 16 seconds. -+ */ -+ if ((new_time <= 0) || (new_time > WDT_MAX_TIME)) -+ return -EINVAL; -+ -+ wdt_timeout = new_time; -+ -+ /* Program the Watchdog */ -+ reg = AT91_WDT_WDRSTEN /* causes watchdog reset */ -+ | AT91_WDT_WDRPROC /* causes processor reset */ -+ | AT91_WDT_WDDBGHLT /* disabled in debug mode */ -+ | AT91_WDT_WDD /* restart at any time */ -+ | (((wdt_timeout * 256) - 1) & AT91_WDT_WDV); /* timer value */ -+ at91_sys_write(AT91_WDT_MR, reg); -+ -+ /* Check if watchdog could be programmed */ -+ mr = at91_sys_read(AT91_WDT_MR); -+ if (mr != reg) { -+ printk(KERN_ERR "at91sam9_wdt: Watchdog register already programmed.\n"); -+ return -EIO; -+ } -+ -+ at91_wdt_reload(); -+ -+ printk(KERN_INFO "AT91SAM9 Watchdog enabled (%d seconds, nowayout)\n", wdt_timeout); -+ return 0; -+} -+ -+static struct watchdog_info at91_wdt_info = { -+ .identity = "at91sam9 watchdog", -+ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING, -+}; -+ -+/* -+ * Handle commands from user-space. -+ */ -+static int at91_wdt_ioctl(struct inode *inode, struct file *file, -+ unsigned int cmd, unsigned long arg) -+{ -+ void __user *argp = (void __user *)arg; -+ int __user *p = argp; -+ int new_value, err; -+ -+ switch (cmd) { -+ case WDIOC_KEEPALIVE: -+ at91_wdt_reload(); /* pat the watchdog */ -+ return 0; -+ -+ case WDIOC_GETSUPPORT: -+ return copy_to_user(argp, &at91_wdt_info, sizeof(at91_wdt_info)) ? -EFAULT : 0; -+ -+ case WDIOC_SETTIMEOUT: -+ if (get_user(new_value, p)) -+ return -EFAULT; -+ -+ err = at91_wdt_settimeout(new_value); -+ if (err) -+ return err; -+ -+ return put_user(wdt_timeout, p); /* return current value */ -+ -+ case WDIOC_GETTIMEOUT: -+ return put_user(wdt_timeout, p); -+ -+ case WDIOC_GETSTATUS: -+ case WDIOC_GETBOOTSTATUS: -+ return put_user(0, p); -+ } -+ return -ENOTTY; -+} -+ -+/* -+ * Pat the watchdog whenever device is written to. -+ */ -+static ssize_t at91_wdt_write(struct file *file, const char *data, size_t len, loff_t *ppos) -+{ -+ at91_wdt_reload(); /* pat the watchdog */ -+ return len; -+} -+ -+/* ......................................................................... */ -+ -+static const struct file_operations at91wdt_fops = { -+ .owner = THIS_MODULE, -+ .llseek = no_llseek, -+ .ioctl = at91_wdt_ioctl, -+ .open = at91_wdt_open, -+ .release = at91_wdt_close, -+ .write = at91_wdt_write, -+}; -+ -+static struct miscdevice at91wdt_miscdev = { -+ .minor = WATCHDOG_MINOR, -+ .name = "watchdog", -+ .fops = &at91wdt_fops, -+}; -+ -+static int __init at91wdt_probe(struct platform_device *pdev) -+{ -+ int res; -+ -+ if (at91wdt_miscdev.parent) -+ return -EBUSY; -+ at91wdt_miscdev.parent = &pdev->dev; -+ -+ res = misc_register(&at91wdt_miscdev); -+ if (res) -+ return res; -+ -+ /* Set watchdog */ -+ if (at91_wdt_settimeout(wdt_timeout) == -EINVAL) { -+ pr_info("at91sam9_wdt: invalid timeout (must be between 1 and %d)\n", WDT_MAX_TIME); -+ return 0; -+ } -+ -+ return 0; -+} -+ -+static int __exit at91wdt_remove(struct platform_device *pdev) -+{ -+ int res; -+ -+ res = misc_deregister(&at91wdt_miscdev); -+ if (!res) -+ at91wdt_miscdev.parent = NULL; -+ -+ return res; -+} -+ -+#ifdef CONFIG_PM -+ -+static int at91wdt_suspend(struct platform_device *pdev, pm_message_t message) -+{ -+ return 0; -+} -+ -+static int at91wdt_resume(struct platform_device *pdev) -+{ -+ return 0; -+} -+ -+#else -+#define at91wdt_suspend NULL -+#define at91wdt_resume NULL -+#endif -+ -+static struct platform_driver at91wdt_driver = { -+ .remove = __exit_p(at91wdt_remove), -+ .suspend = at91wdt_suspend, -+ .resume = at91wdt_resume, -+ .driver = { -+ .name = "at91_wdt", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+static int __init at91sam_wdt_init(void) -+{ -+ return platform_driver_probe(&at91wdt_driver, at91wdt_probe); -+} -+ -+static void __exit at91sam_wdt_exit(void) -+{ -+ platform_driver_unregister(&at91wdt_driver); -+} -+ -+module_init(at91sam_wdt_init); -+module_exit(at91sam_wdt_exit); -+ -+MODULE_AUTHOR("Renaud CERRATO"); -+MODULE_DESCRIPTION("Watchdog driver for Atmel AT91SAM9x processors"); -+MODULE_LICENSE("GPL"); -+MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR); -+MODULE_ALIAS("platform:at91_wdt"); ---- a/include/asm-arm/arch-at91/at91_ecc.h -+++ b/include/asm-arm/arch-at91/at91_ecc.h -@@ -1,6 +1,9 @@ - /* - * include/asm-arm/arch-at91/at91_ecc.h - * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Error Corrected Code Controller (ECC) - System peripherals regsters. - * Based on AT91SAM9260 datasheet revision B. - * -@@ -13,26 +16,26 @@ - #ifndef AT91_ECC_H - #define AT91_ECC_H - --#define AT91_ECC_CR (AT91_ECC + 0x00) /* Control register */ -+#define AT91_ECC_CR 0x00 /* Control register */ - #define AT91_ECC_RST (1 << 0) /* Reset parity */ - --#define AT91_ECC_MR (AT91_ECC + 0x04) /* Mode register */ -+#define AT91_ECC_MR 0x04 /* Mode register */ - #define AT91_ECC_PAGESIZE (3 << 0) /* Page Size */ - #define AT91_ECC_PAGESIZE_528 (0) - #define AT91_ECC_PAGESIZE_1056 (1) - #define AT91_ECC_PAGESIZE_2112 (2) - #define AT91_ECC_PAGESIZE_4224 (3) - --#define AT91_ECC_SR (AT91_ECC + 0x08) /* Status register */ -+#define AT91_ECC_SR 0x08 /* Status register */ - #define AT91_ECC_RECERR (1 << 0) /* Recoverable Error */ - #define AT91_ECC_ECCERR (1 << 1) /* ECC Single Bit Error */ - #define AT91_ECC_MULERR (1 << 2) /* Multiple Errors */ - --#define AT91_ECC_PR (AT91_ECC + 0x0c) /* Parity register */ -+#define AT91_ECC_PR 0x0c /* Parity register */ - #define AT91_ECC_BITADDR (0xf << 0) /* Bit Error Address */ - #define AT91_ECC_WORDADDR (0xfff << 4) /* Word Error Address */ - --#define AT91_ECC_NPR (AT91_ECC + 0x10) /* NParity register */ -+#define AT91_ECC_NPR 0x10 /* NParity register */ - #define AT91_ECC_NPARITY (0xffff << 0) /* NParity */ - - #endif ---- a/include/asm-arm/arch-at91/at91_pit.h -+++ b/include/asm-arm/arch-at91/at91_pit.h -@@ -1,6 +1,9 @@ - /* - * include/asm-arm/arch-at91/at91_pit.h - * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Periodic Interval Timer (PIT) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * ---- a/include/asm-arm/arch-at91/at91_pmc.h -+++ b/include/asm-arm/arch-at91/at91_pmc.h -@@ -23,6 +23,7 @@ - #define AT91_PMC_PCK (1 << 0) /* Processor Clock */ - #define AT91RM9200_PMC_UDP (1 << 1) /* USB Devcice Port Clock [AT91RM9200 only] */ - #define AT91RM9200_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */ -+#define AT91CAP9_PMC_DDR (1 << 2) /* DDR Clock [AT91CAP9 revC only] */ - #define AT91RM9200_PMC_UHP (1 << 4) /* USB Host Port Clock [AT91RM9200 only] */ - #define AT91SAM926x_PMC_UHP (1 << 6) /* USB Host Port Clock [AT91SAM926x only] */ - #define AT91CAP9_PMC_UHP (1 << 6) /* USB Host Port Clock [AT91CAP9 only] */ -@@ -39,10 +40,14 @@ - #define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */ - - #define AT91_CKGR_UCKR (AT91_PMC + 0x1C) /* UTMI Clock Register [SAM9RL, CAP9] */ -+#define AT91_PMC_UPLLEN (1 << 16) /* UTMI PLL Enable */ -+#define AT91_PMC_UPLLCOUNT (0xf << 20) /* UTMI PLL Start-up Time */ -+#define AT91_PMC_BIASEN (1 << 24) /* UTMI BIAS Enable */ -+#define AT91_PMC_BIASCOUNT (0xf << 28) /* UTMI PLL Start-up Time */ - - #define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */ - #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */ --#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [AT91SAM926x only] */ -+#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [SAM9x, CAP9] */ - #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */ - - #define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */ -@@ -56,6 +61,7 @@ - #define AT91_PMC_OUT (3 << 14) /* PLL Clock Frequency Range */ - #define AT91_PMC_MUL (0x7ff << 16) /* PLL Multiplier */ - #define AT91_PMC_USBDIV (3 << 28) /* USB Divisor (PLLB only) */ -+#define AT91CAP9_PMC_USBDIV (0xf << 28) /* USB Divisor (PLLB only) [AT91CAP9 revC only] */ - #define AT91_PMC_USBDIV_1 (0 << 28) - #define AT91_PMC_USBDIV_2 (1 << 28) - #define AT91_PMC_USBDIV_4 (2 << 28) -@@ -76,10 +82,13 @@ - #define AT91_PMC_PRES_32 (5 << 2) - #define AT91_PMC_PRES_64 (6 << 2) - #define AT91_PMC_MDIV (3 << 8) /* Master Clock Division */ --#define AT91_PMC_MDIV_1 (0 << 8) --#define AT91_PMC_MDIV_2 (1 << 8) --#define AT91_PMC_MDIV_3 (2 << 8) --#define AT91_PMC_MDIV_4 (3 << 8) -+#define AT91RM9200_PMC_MDIV_1 (0 << 8) /* [AT91RM9200 only] */ -+#define AT91RM9200_PMC_MDIV_2 (1 << 8) -+#define AT91RM9200_PMC_MDIV_3 (2 << 8) -+#define AT91RM9200_PMC_MDIV_4 (3 << 8) -+#define AT91SAM9_PMC_MDIV_1 (0 << 8) /* [SAM9,CAP9 only] */ -+#define AT91SAM9_PMC_MDIV_2 (1 << 8) -+#define AT91SAM9_PMC_MDIV_4 (2 << 8) - - #define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-3 Registers */ - -@@ -90,10 +99,17 @@ - #define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */ - #define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */ - #define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */ -+#define AT91_PMC_LOCKU (1 << 6) /* UPLL Lock [AT91CAP9 only] */ -+#define AT91_PMC_OSCSEL (1 << 7) /* Slow Clock Oscillator [AT91CAP9 revC only] */ - #define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */ - #define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */ - #define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */ - #define AT91_PMC_PCK3RDY (1 << 11) /* Programmable Clock 3 */ - #define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */ - -+#define AT91_PMC_PROT (AT91_PMC + 0xe4) /* Protect Register [AT91CAP9 revC only] */ -+#define AT91_PMC_PROTKEY 0x504d4301 /* Activation Code */ -+ -+#define AT91_PMC_VER (AT91_PMC + 0xfc) /* PMC Module Version [AT91CAP9 only] */ -+ - #endif ---- a/include/asm-arm/arch-at91/at91_rstc.h -+++ b/include/asm-arm/arch-at91/at91_rstc.h -@@ -1,6 +1,9 @@ - /* - * include/asm-arm/arch-at91/at91_rstc.h - * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Reset Controller (RSTC) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * ---- a/include/asm-arm/arch-at91/at91_rtt.h -+++ b/include/asm-arm/arch-at91/at91_rtt.h -@@ -1,6 +1,9 @@ - /* - * include/asm-arm/arch-at91/at91_rtt.h - * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Real-time Timer (RTT) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * ---- a/include/asm-arm/arch-at91/at91_shdwc.h -+++ b/include/asm-arm/arch-at91/at91_shdwc.h -@@ -1,6 +1,9 @@ - /* - * include/asm-arm/arch-at91/at91_shdwc.h - * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Shutdown Controller (SHDWC) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * -@@ -24,10 +27,12 @@ - #define AT91_SHDW_WKMODE0_LOW 2 - #define AT91_SHDW_WKMODE0_ANYLEVEL 3 - #define AT91_SHDW_CPTWK0 (0xf << 4) /* Counter On Wake Up 0 */ -+#define AT91_SHDW_CPTWK0_(x) ((x) << 4) - #define AT91_SHDW_RTTWKEN (1 << 16) /* Real Time Timer Wake-up Enable */ - - #define AT91_SHDW_SR (AT91_SHDWC + 0x08) /* Shut Down Status Register */ - #define AT91_SHDW_WAKEUP0 (1 << 0) /* Wake-up 0 Status */ - #define AT91_SHDW_RTTWK (1 << 16) /* Real-time Timer Wake-up */ -+#define AT91_SHDW_RTCWK (1 << 17) /* Real-time Clock Wake-up [SAM9RL] */ - - #endif ---- /dev/null -+++ b/include/asm-arm/arch-at91/at91_tsc.h -@@ -0,0 +1,76 @@ -+/* -+ * include/asm-arm/arch-at91/at91_tsc.h -+ * -+ * Copyright (C) 2008 Andrew Victor -+ * -+ * Touch Screen ADC Controller (TSC) -+ * Based on AT91SAM9RL64 preliminary draft datasheet. -+ * -+ * This program is free software; you can redistribute it and/or modify it -+ * under the terms of the GNU General Public License as published by the -+ * Free Software Foundation; either version 2 of the License, or (at your -+ * option) any later version. -+ */ -+ -+#ifndef AT91_TSC_H -+#define AT91_TSC_H -+ -+#define AT91_TSADCC_CR 0x00 /* Control register */ -+#define AT91_TSADCC_SWRST (1 << 0) /* Software Reset*/ -+#define AT91_TSADCC_START (1 << 1) /* Start conversion */ -+ -+#define AT91_TSADCC_MR 0x04 /* Mode register */ -+#define AT91_TSADCC_TSAMOD (3 << 0) /* ADC mode */ -+#define AT91_TSADCC_LOWRES (1 << 4) /* Resolution selection */ -+#define AT91_TSADCC_SLEEP (1 << 5) /* Sleep mode */ -+#define AT91_TSADCC_PENDET (1 << 6) /* Pen Detect selection */ -+#define AT91_TSADCC_PRESCAL (0x3f << 8) /* Prescalar Rate Selection */ -+#define AT91_TSADCC_STARTUP (0x7f << 16) /* Start Up time */ -+#define AT91_TSADCC_SHTIM (0xf << 24) /* Sample & Hold time */ -+#define AT91_TSADCC_PENDBC (0xf << 28) /* Pen Detect debouncing time */ -+ -+#define AT91_TSADCC_TRGR 0x08 /* Trigger register */ -+#define AT91_TSADCC_TRGMOD (7 << 0) /* Trigger mode */ -+#define AT91_TSADCC_TRGMOD_NONE (0 << 0) -+#define AT91_TSADCC_TRGMOD_EXT_RISING (1 << 0) -+#define AT91_TSADCC_TRGMOD_EXT_FALLING (2 << 0) -+#define AT91_TSADCC_TRGMOD_EXT_ANY (3 << 0) -+#define AT91_TSADCC_TRGMOD_PENDET (4 << 0) -+#define AT91_TSADCC_TRGMOD_PERIOD (5 << 0) -+#define AT91_TSADCC_TRGMOD_CONTINUOUS (6 << 0) -+#define AT91_TSADCC_TRGPER (0xffff << 16) /* Trigger period */ -+ -+#define AT91_TSADCC_TSR 0x0C /* Touch Screen register */ -+#define AT91_TSADCC_TSFREQ (0xf << 0) /* TS Frequency in Interleaved mode */ -+#define AT91_TSADCC_TSSHTIM (0xf << 24) /* Sample & Hold time */ -+ -+#define AT91_TSADCC_CHER 0x10 /* Channel Enable register */ -+#define AT91_TSADCC_CHDR 0x14 /* Channel Disable register */ -+#define AT91_TSADCC_CHSR 0x18 /* Channel Status register */ -+#define AT91_TSADCC_CH(n) (1 << (n)) /* Channel number */ -+ -+#define AT91_TSADCC_SR 0x1C /* Status register */ -+#define AT91_TSADCC_EOC(n) (1 << ((n)+0)) /* End of conversion for channel N */ -+#define AT91_TSADCC_OVRE(n) (1 << ((n)+8)) /* Overrun error for channel N */ -+#define AT91_TSADCC_DRDY (1 << 16) /* Data Ready */ -+#define AT91_TSADCC_GOVRE (1 << 17) /* General Overrun Error */ -+#define AT91_TSADCC_ENDRX (1 << 18) /* End of RX Buffer */ -+#define AT91_TSADCC_RXBUFF (1 << 19) /* TX Buffer full */ -+#define AT91_TSADCC_PENCNT (1 << 20) /* Pen contact */ -+#define AT91_TSADCC_NOCNT (1 << 21) /* No contact */ -+ -+#define AT91_TSADCC_LCDR 0x20 /* Last Converted Data register */ -+#define AT91_TSADCC_DATA (0x3ff << 0) /* Channel data */ -+ -+#define AT91_TSADCC_IER 0x24 /* Interrupt Enable register */ -+#define AT91_TSADCC_IDR 0x28 /* Interrupt Disable register */ -+#define AT91_TSADCC_IMR 0x2C /* Interrupt Mask register */ -+#define AT91_TSADCC_CDR0 0x30 /* Channel Data 0 */ -+#define AT91_TSADCC_CDR1 0x34 /* Channel Data 1 */ -+#define AT91_TSADCC_CDR2 0x38 /* Channel Data 2 */ -+#define AT91_TSADCC_CDR3 0x3C /* Channel Data 3 */ -+#define AT91_TSADCC_CDR4 0x40 /* Channel Data 4 */ -+#define AT91_TSADCC_CDR5 0x44 /* Channel Data 5 */ -+ -+#endif -+ ---- a/include/asm-arm/arch-at91/at91_wdt.h -+++ b/include/asm-arm/arch-at91/at91_wdt.h -@@ -1,6 +1,9 @@ - /* - * include/asm-arm/arch-at91/at91_wdt.h - * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Watchdog Timer (WDT) - System peripherals regsters. - * Based on AT91SAM9261 datasheet revision D. - * ---- a/include/asm-arm/arch-at91/at91cap9.h -+++ b/include/asm-arm/arch-at91/at91cap9.h -@@ -101,7 +101,10 @@ - #define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) - #define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) - #define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) --#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS) -+#define AT91_SCKCR (0xfffffd50 - AT91_BASE_SYS) -+#define AT91_GPBR (cpu_is_at91cap9_revB() ? \ -+ (0xfffffd50 - AT91_BASE_SYS) : \ -+ (0xfffffd60 - AT91_BASE_SYS)) - - #define AT91_USART0 AT91CAP9_BASE_US0 - #define AT91_USART1 AT91CAP9_BASE_US1 -@@ -118,7 +121,7 @@ - #define AT91CAP9_ROM_SIZE (32 * SZ_1K) /* Internal ROM size (32Kb) */ - - #define AT91CAP9_LCDC_BASE 0x00500000 /* LCD Controller */ --#define AT91CAP9_UDPHS_BASE 0x00600000 /* USB High Speed Device Port */ -+#define AT91CAP9_UDPHS_FIFO 0x00600000 /* USB High Speed Device Port */ - #define AT91CAP9_UHP_BASE 0x00700000 /* USB Host controller */ - - #define CONFIG_DRAM_BASE AT91_CHIPSELECT_6 ---- /dev/null -+++ b/include/asm-arm/arch-at91/at91cap9_ddrsdr.h -@@ -0,0 +1,102 @@ -+/* -+ * include/asm-arm/arch-at91/at91cap9_ddrsdr.h -+ * -+ * (C) 2008 Andrew Victor -+ * -+ * DDR/SDR Controller (DDRSDRC) - System peripherals registers. -+ * Based on AT91CAP9 datasheet revision B. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ */ -+ -+#ifndef AT91CAP9_DDRSDR_H -+#define AT91CAP9_DDRSDR_H -+ -+#define AT91_DDRSDRC_MR (AT91_DDRSDRC + 0x00) /* Mode Register */ -+#define AT91_DDRSDRC_MODE (0xf << 0) /* Command Mode */ -+#define AT91_DDRSDRC_MODE_NORMAL 0 -+#define AT91_DDRSDRC_MODE_NOP 1 -+#define AT91_DDRSDRC_MODE_PRECHARGE 2 -+#define AT91_DDRSDRC_MODE_LMR 3 -+#define AT91_DDRSDRC_MODE_REFRESH 4 -+#define AT91_DDRSDRC_MODE_EXT_LMR 5 -+#define AT91_DDRSDRC_MODE_DEEP 6 -+ -+#define AT91_DDRSDRC_RTR (AT91_DDRSDRC + 0x04) /* Refresh Timer Register */ -+#define AT91_DDRSDRC_COUNT (0xfff << 0) /* Refresh Timer Counter */ -+ -+#define AT91_DDRSDRC_CR (AT91_DDRSDRC + 0x08) /* Configuration Register */ -+#define AT91_DDRSDRC_NC (3 << 0) /* Number of Column Bits */ -+#define AT91_DDRSDRC_NC_SDR8 (0 << 0) -+#define AT91_DDRSDRC_NC_SDR9 (1 << 0) -+#define AT91_DDRSDRC_NC_SDR10 (2 << 0) -+#define AT91_DDRSDRC_NC_SDR11 (3 << 0) -+#define AT91_DDRSDRC_NC_DDR9 (0 << 0) -+#define AT91_DDRSDRC_NC_DDR10 (1 << 0) -+#define AT91_DDRSDRC_NC_DDR11 (2 << 0) -+#define AT91_DDRSDRC_NC_DDR12 (3 << 0) -+#define AT91_DDRSDRC_NR (3 << 2) /* Number of Row Bits */ -+#define AT91_DDRSDRC_NR_11 (0 << 2) -+#define AT91_DDRSDRC_NR_12 (1 << 2) -+#define AT91_DDRSDRC_NR_13 (2 << 2) -+#define AT91_DDRSDRC_CAS (7 << 4) /* CAS Latency */ -+#define AT91_DDRSDRC_CAS_2 (2 << 4) -+#define AT91_DDRSDRC_CAS_3 (3 << 4) -+#define AT91_DDRSDRC_CAS_25 (6 << 4) -+#define AT91_DDRSDRC_DLL (1 << 7) /* Reset DLL */ -+#define AT91_DDRSDRC_DICDS (1 << 8) /* Output impedance control */ -+ -+#define AT91_DDRSDRC_T0PR (AT91_DDRSDRC + 0x0C) /* Timing 0 Register */ -+#define AT91_DDRSDRC_TRAS (0xf << 0) /* Active to Precharge delay */ -+#define AT91_DDRSDRC_TRCD (0xf << 4) /* Row to Column delay */ -+#define AT91_DDRSDRC_TWR (0xf << 8) /* Write recovery delay */ -+#define AT91_DDRSDRC_TRC (0xf << 12) /* Row cycle delay */ -+#define AT91_DDRSDRC_TRP (0xf << 16) /* Row precharge delay */ -+#define AT91_DDRSDRC_TRRD (0xf << 20) /* Active BankA to BankB */ -+#define AT91_DDRSDRC_TWTR (1 << 24) /* Internal Write to Read delay */ -+#define AT91_DDRSDRC_TMRD (0xf << 28) /* Load mode to active/refresh delay */ -+ -+#define AT91_DDRSDRC_T1PR (AT91_DDRSDRC + 0x10) /* Timing 1 Register */ -+#define AT91_DDRSDRC_TRFC (0x1f << 0) /* Row Cycle Delay */ -+#define AT91_DDRSDRC_TXSNR (0xff << 8) /* Exit self-refresh to non-read */ -+#define AT91_DDRSDRC_TXSRD (0xff << 16) /* Exit self-refresh to read */ -+#define AT91_DDRSDRC_TXP (0xf << 24) /* Exit power-down delay */ -+ -+#define AT91_DDRSDRC_LPR (AT91_DDRSDRC + 0x18) /* Low Power Register */ -+#define AT91_DDRSDRC_LPCB (3 << 0) /* Low-power Configurations */ -+#define AT91_DDRSDRC_LPCB_DISABLE 0 -+#define AT91_DDRSDRC_LPCB_SELF_REFRESH 1 -+#define AT91_DDRSDRC_LPCB_POWER_DOWN 2 -+#define AT91_DDRSDRC_LPCB_DEEP_POWER_DOWN 3 -+#define AT91_DDRSDRC_CLKFR (1 << 2) /* Clock Frozen */ -+#define AT91_DDRSDRC_PASR (7 << 4) /* Partial Array Self Refresh */ -+#define AT91_DDRSDRC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */ -+#define AT91_DDRSDRC_DS (3 << 10) /* Drive Strength */ -+#define AT91_DDRSDRC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */ -+#define AT91_DDRSDRC_TIMEOUT_0_CLK_CYCLES (0 << 12) -+#define AT91_DDRSDRC_TIMEOUT_64_CLK_CYCLES (1 << 12) -+#define AT91_DDRSDRC_TIMEOUT_128_CLK_CYCLES (2 << 12) -+ -+#define AT91_DDRSDRC_MDR (AT91_DDRSDRC + 0x1C) /* Memory Device Register */ -+#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */ -+#define AT91_DDRSDRC_MD_SDR 0 -+#define AT91_DDRSDRC_MD_LOW_POWER_SDR 1 -+#define AT91_DDRSDRC_MD_DDR 2 -+#define AT91_DDRSDRC_MD_LOW_POWER_DDR 3 -+ -+#define AT91_DDRSDRC_DLLR (AT91_DDRSDRC + 0x20) /* DLL Information Register */ -+#define AT91_DDRSDRC_MDINC (1 << 0) /* Master Delay increment */ -+#define AT91_DDRSDRC_MDDEC (1 << 1) /* Master Delay decrement */ -+#define AT91_DDRSDRC_MDOVF (1 << 2) /* Master Delay Overflow */ -+#define AT91_DDRSDRC_SDCOVF (1 << 3) /* Slave Delay Correction Overflow */ -+#define AT91_DDRSDRC_SDCUDF (1 << 4) /* Slave Delay Correction Underflow */ -+#define AT91_DDRSDRC_SDERF (1 << 5) /* Slave Delay Correction error */ -+#define AT91_DDRSDRC_MDVAL (0xff << 8) /* Master Delay value */ -+#define AT91_DDRSDRC_SDVAL (0xff << 16) /* Slave Delay value */ -+#define AT91_DDRSDRC_SDCVAL (0xff << 24) /* Slave Delay Correction value */ -+ -+ -+#endif ---- a/include/asm-arm/arch-at91/at91cap9_matrix.h -+++ b/include/asm-arm/arch-at91/at91cap9_matrix.h -@@ -106,6 +106,11 @@ - #define AT91_MPBS0_SFR (AT91_MATRIX + 0x114) /* MPBlock Slave 0 Special Function Register */ - #define AT91_MPBS1_SFR (AT91_MATRIX + 0x11C) /* MPBlock Slave 1 Special Function Register */ - -+#define AT91_MATRIX_UDPHS (AT91_MATRIX + 0x118) /* USBHS Special Function Register [AT91CAP9 only] */ -+#define AT91_MATRIX_SELECT_UDPHS (0 << 31) /* select High Speed UDP */ -+#define AT91_MATRIX_SELECT_UDP (1 << 31) /* select standard UDP */ -+#define AT91_MATRIX_UDPHS_BYPASS_LOCK (1 << 30) /* bypass lock bit */ -+ - #define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x120) /* EBI Chip Select Assignment Register */ - #define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ - #define AT91_MATRIX_EBI_CS1A_SMC (0 << 1) ---- a/include/asm-arm/arch-at91/at91sam9260_matrix.h -+++ b/include/asm-arm/arch-at91/at91sam9260_matrix.h -@@ -1,6 +1,8 @@ - /* - * include/asm-arm/arch-at91/at91sam9260_matrix.h - * -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9260 datasheet revision B. - * ---- a/include/asm-arm/arch-at91/at91sam9261_matrix.h -+++ b/include/asm-arm/arch-at91/at91sam9261_matrix.h -@@ -1,6 +1,8 @@ - /* - * include/asm-arm/arch-at91/at91sam9261_matrix.h - * -+ * Copyright (C) 2007 Atmel Corporation. -+ * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9261 datasheet revision D. - * ---- a/include/asm-arm/arch-at91/at91sam926x_mc.h -+++ /dev/null -@@ -1,141 +0,0 @@ --/* -- * include/asm-arm/arch-at91/at91sam926x_mc.h -- * -- * Memory Controllers (SMC, SDRAMC) - System peripherals registers. -- * Based on AT91SAM9261 datasheet revision D. -- * -- * This program is free software; you can redistribute it and/or modify -- * it under the terms of the GNU General Public License as published by -- * the Free Software Foundation; either version 2 of the License, or -- * (at your option) any later version. -- */ -- --#ifndef AT91SAM926x_MC_H --#define AT91SAM926x_MC_H -- --/* SDRAM Controller (SDRAMC) registers */ --#define AT91_SDRAMC_MR (AT91_SDRAMC + 0x00) /* SDRAM Controller Mode Register */ --#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */ --#define AT91_SDRAMC_MODE_NORMAL 0 --#define AT91_SDRAMC_MODE_NOP 1 --#define AT91_SDRAMC_MODE_PRECHARGE 2 --#define AT91_SDRAMC_MODE_LMR 3 --#define AT91_SDRAMC_MODE_REFRESH 4 --#define AT91_SDRAMC_MODE_EXT_LMR 5 --#define AT91_SDRAMC_MODE_DEEP 6 -- --#define AT91_SDRAMC_TR (AT91_SDRAMC + 0x04) /* SDRAM Controller Refresh Timer Register */ --#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Counter */ -- --#define AT91_SDRAMC_CR (AT91_SDRAMC + 0x08) /* SDRAM Controller Configuration Register */ --#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */ --#define AT91_SDRAMC_NC_8 (0 << 0) --#define AT91_SDRAMC_NC_9 (1 << 0) --#define AT91_SDRAMC_NC_10 (2 << 0) --#define AT91_SDRAMC_NC_11 (3 << 0) --#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */ --#define AT91_SDRAMC_NR_11 (0 << 2) --#define AT91_SDRAMC_NR_12 (1 << 2) --#define AT91_SDRAMC_NR_13 (2 << 2) --#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */ --#define AT91_SDRAMC_NB_2 (0 << 4) --#define AT91_SDRAMC_NB_4 (1 << 4) --#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */ --#define AT91_SDRAMC_CAS_1 (1 << 5) --#define AT91_SDRAMC_CAS_2 (2 << 5) --#define AT91_SDRAMC_CAS_3 (3 << 5) --#define AT91_SDRAMC_DBW (1 << 7) /* Data Bus Width */ --#define AT91_SDRAMC_DBW_32 (0 << 7) --#define AT91_SDRAMC_DBW_16 (1 << 7) --#define AT91_SDRAMC_TWR (0xf << 8) /* Write Recovery Delay */ --#define AT91_SDRAMC_TRC (0xf << 12) /* Row Cycle Delay */ --#define AT91_SDRAMC_TRP (0xf << 16) /* Row Precharge Delay */ --#define AT91_SDRAMC_TRCD (0xf << 20) /* Row to Column Delay */ --#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to Precharge Delay */ --#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self Refresh to Active Delay */ -- --#define AT91_SDRAMC_LPR (AT91_SDRAMC + 0x10) /* SDRAM Controller Low Power Register */ --#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power Configurations */ --#define AT91_SDRAMC_LPCB_DISABLE 0 --#define AT91_SDRAMC_LPCB_SELF_REFRESH 1 --#define AT91_SDRAMC_LPCB_POWER_DOWN 2 --#define AT91_SDRAMC_LPCB_DEEP_POWER_DOWN 3 --#define AT91_SDRAMC_PASR (7 << 4) /* Partial Array Self Refresh */ --#define AT91_SDRAMC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */ --#define AT91_SDRAMC_DS (3 << 10) /* Drive Strenght */ --#define AT91_SDRAMC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */ --#define AT91_SDRAMC_TIMEOUT_0_CLK_CYCLES (0 << 12) --#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12) --#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12) -- --#define AT91_SDRAMC_IER (AT91_SDRAMC + 0x14) /* SDRAM Controller Interrupt Enable Register */ --#define AT91_SDRAMC_IDR (AT91_SDRAMC + 0x18) /* SDRAM Controller Interrupt Disable Register */ --#define AT91_SDRAMC_IMR (AT91_SDRAMC + 0x1C) /* SDRAM Controller Interrupt Mask Register */ --#define AT91_SDRAMC_ISR (AT91_SDRAMC + 0x20) /* SDRAM Controller Interrupt Status Register */ --#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error Status */ -- --#define AT91_SDRAMC_MDR (AT91_SDRAMC + 0x24) /* SDRAM Memory Device Register */ --#define AT91_SDRAMC_MD (3 << 0) /* Memory Device Type */ --#define AT91_SDRAMC_MD_SDRAM 0 --#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1 -- -- --/* Static Memory Controller (SMC) registers */ --#define AT91_SMC_SETUP(n) (AT91_SMC + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ --#define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */ --#define AT91_SMC_NWESETUP_(x) ((x) << 0) --#define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */ --#define AT91_SMC_NCS_WRSETUP_(x) ((x) << 8) --#define AT91_SMC_NRDSETUP (0x3f << 16) /* NRD Setup Length */ --#define AT91_SMC_NRDSETUP_(x) ((x) << 16) --#define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */ --#define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24) -- --#define AT91_SMC_PULSE(n) (AT91_SMC + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ --#define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */ --#define AT91_SMC_NWEPULSE_(x) ((x) << 0) --#define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */ --#define AT91_SMC_NCS_WRPULSE_(x)((x) << 8) --#define AT91_SMC_NRDPULSE (0x7f << 16) /* NRD Pulse Length */ --#define AT91_SMC_NRDPULSE_(x) ((x) << 16) --#define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */ --#define AT91_SMC_NCS_RDPULSE_(x)((x) << 24) -- --#define AT91_SMC_CYCLE(n) (AT91_SMC + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ --#define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */ --#define AT91_SMC_NWECYCLE_(x) ((x) << 0) --#define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */ --#define AT91_SMC_NRDCYCLE_(x) ((x) << 16) -- --#define AT91_SMC_MODE(n) (AT91_SMC + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ --#define AT91_SMC_READMODE (1 << 0) /* Read Mode */ --#define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */ --#define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */ --#define AT91_SMC_EXNWMODE_DISABLE (0 << 4) --#define AT91_SMC_EXNWMODE_FROZEN (2 << 4) --#define AT91_SMC_EXNWMODE_READY (3 << 4) --#define AT91_SMC_BAT (1 << 8) /* Byte Access Type */ --#define AT91_SMC_BAT_SELECT (0 << 8) --#define AT91_SMC_BAT_WRITE (1 << 8) --#define AT91_SMC_DBW (3 << 12) /* Data Bus Width */ --#define AT91_SMC_DBW_8 (0 << 12) --#define AT91_SMC_DBW_16 (1 << 12) --#define AT91_SMC_DBW_32 (2 << 12) --#define AT91_SMC_TDF (0xf << 16) /* Data Float Time. */ --#define AT91_SMC_TDF_(x) ((x) << 16) --#define AT91_SMC_TDFMODE (1 << 20) /* TDF Optimization - Enabled */ --#define AT91_SMC_PMEN (1 << 24) /* Page Mode Enabled */ --#define AT91_SMC_PS (3 << 28) /* Page Size */ --#define AT91_SMC_PS_4 (0 << 28) --#define AT91_SMC_PS_8 (1 << 28) --#define AT91_SMC_PS_16 (2 << 28) --#define AT91_SMC_PS_32 (3 << 28) -- --#if defined(AT91_SMC1) /* The AT91SAM9263 has 2 Static Memory contollers */ --#define AT91_SMC1_SETUP(n) (AT91_SMC1 + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ --#define AT91_SMC1_PULSE(n) (AT91_SMC1 + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ --#define AT91_SMC1_CYCLE(n) (AT91_SMC1 + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ --#define AT91_SMC1_MODE(n) (AT91_SMC1 + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ --#endif -- --#endif ---- /dev/null -+++ b/include/asm-arm/arch-at91/at91sam9_sdramc.h -@@ -0,0 +1,86 @@ -+/* -+ * include/asm-arm/arch-at91/at91sam9_sdramc.h -+ * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * -+ * SDRAM Controllers (SDRAMC) - System peripherals registers. -+ * Based on AT91SAM9261 datasheet revision D. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ */ -+ -+#ifndef AT91SAM9_SDRAMC_H -+#define AT91SAM9_SDRAMC_H -+ -+/* SDRAM Controller (SDRAMC) registers */ -+#define AT91_SDRAMC_MR (AT91_SDRAMC + 0x00) /* SDRAM Controller Mode Register */ -+#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */ -+#define AT91_SDRAMC_MODE_NORMAL 0 -+#define AT91_SDRAMC_MODE_NOP 1 -+#define AT91_SDRAMC_MODE_PRECHARGE 2 -+#define AT91_SDRAMC_MODE_LMR 3 -+#define AT91_SDRAMC_MODE_REFRESH 4 -+#define AT91_SDRAMC_MODE_EXT_LMR 5 -+#define AT91_SDRAMC_MODE_DEEP 6 -+ -+#define AT91_SDRAMC_TR (AT91_SDRAMC + 0x04) /* SDRAM Controller Refresh Timer Register */ -+#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Counter */ -+ -+#define AT91_SDRAMC_CR (AT91_SDRAMC + 0x08) /* SDRAM Controller Configuration Register */ -+#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */ -+#define AT91_SDRAMC_NC_8 (0 << 0) -+#define AT91_SDRAMC_NC_9 (1 << 0) -+#define AT91_SDRAMC_NC_10 (2 << 0) -+#define AT91_SDRAMC_NC_11 (3 << 0) -+#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */ -+#define AT91_SDRAMC_NR_11 (0 << 2) -+#define AT91_SDRAMC_NR_12 (1 << 2) -+#define AT91_SDRAMC_NR_13 (2 << 2) -+#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */ -+#define AT91_SDRAMC_NB_2 (0 << 4) -+#define AT91_SDRAMC_NB_4 (1 << 4) -+#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */ -+#define AT91_SDRAMC_CAS_1 (1 << 5) -+#define AT91_SDRAMC_CAS_2 (2 << 5) -+#define AT91_SDRAMC_CAS_3 (3 << 5) -+#define AT91_SDRAMC_DBW (1 << 7) /* Data Bus Width */ -+#define AT91_SDRAMC_DBW_32 (0 << 7) -+#define AT91_SDRAMC_DBW_16 (1 << 7) -+#define AT91_SDRAMC_TWR (0xf << 8) /* Write Recovery Delay */ -+#define AT91_SDRAMC_TRC (0xf << 12) /* Row Cycle Delay */ -+#define AT91_SDRAMC_TRP (0xf << 16) /* Row Precharge Delay */ -+#define AT91_SDRAMC_TRCD (0xf << 20) /* Row to Column Delay */ -+#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to Precharge Delay */ -+#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self Refresh to Active Delay */ -+ -+#define AT91_SDRAMC_LPR (AT91_SDRAMC + 0x10) /* SDRAM Controller Low Power Register */ -+#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power Configurations */ -+#define AT91_SDRAMC_LPCB_DISABLE 0 -+#define AT91_SDRAMC_LPCB_SELF_REFRESH 1 -+#define AT91_SDRAMC_LPCB_POWER_DOWN 2 -+#define AT91_SDRAMC_LPCB_DEEP_POWER_DOWN 3 -+#define AT91_SDRAMC_PASR (7 << 4) /* Partial Array Self Refresh */ -+#define AT91_SDRAMC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */ -+#define AT91_SDRAMC_DS (3 << 10) /* Drive Strength */ -+#define AT91_SDRAMC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */ -+#define AT91_SDRAMC_TIMEOUT_0_CLK_CYCLES (0 << 12) -+#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12) -+#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12) -+ -+#define AT91_SDRAMC_IER (AT91_SDRAMC + 0x14) /* SDRAM Controller Interrupt Enable Register */ -+#define AT91_SDRAMC_IDR (AT91_SDRAMC + 0x18) /* SDRAM Controller Interrupt Disable Register */ -+#define AT91_SDRAMC_IMR (AT91_SDRAMC + 0x1C) /* SDRAM Controller Interrupt Mask Register */ -+#define AT91_SDRAMC_ISR (AT91_SDRAMC + 0x20) /* SDRAM Controller Interrupt Status Register */ -+#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error Status */ -+ -+#define AT91_SDRAMC_MDR (AT91_SDRAMC + 0x24) /* SDRAM Memory Device Register */ -+#define AT91_SDRAMC_MD (3 << 0) /* Memory Device Type */ -+#define AT91_SDRAMC_MD_SDRAM 0 -+#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1 -+ -+ -+#endif ---- /dev/null -+++ b/include/asm-arm/arch-at91/at91sam9_smc.h -@@ -0,0 +1,76 @@ -+/* -+ * include/asm-arm/arch-at91/at91sam9_smc.h -+ * -+ * Copyright (C) 2007 Andrew Victor -+ * Copyright (C) 2007 Atmel Corporation. -+ * -+ * Static Memory Controllers (SMC) - System peripherals registers. -+ * Based on AT91SAM9261 datasheet revision D. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ */ -+ -+#ifndef AT91SAM9_SMC_H -+#define AT91SAM9_SMC_H -+ -+#define AT91_SMC_SETUP(n) (AT91_SMC + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ -+#define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */ -+#define AT91_SMC_NWESETUP_(x) ((x) << 0) -+#define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */ -+#define AT91_SMC_NCS_WRSETUP_(x) ((x) << 8) -+#define AT91_SMC_NRDSETUP (0x3f << 16) /* NRD Setup Length */ -+#define AT91_SMC_NRDSETUP_(x) ((x) << 16) -+#define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */ -+#define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24) -+ -+#define AT91_SMC_PULSE(n) (AT91_SMC + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ -+#define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */ -+#define AT91_SMC_NWEPULSE_(x) ((x) << 0) -+#define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */ -+#define AT91_SMC_NCS_WRPULSE_(x)((x) << 8) -+#define AT91_SMC_NRDPULSE (0x7f << 16) /* NRD Pulse Length */ -+#define AT91_SMC_NRDPULSE_(x) ((x) << 16) -+#define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */ -+#define AT91_SMC_NCS_RDPULSE_(x)((x) << 24) -+ -+#define AT91_SMC_CYCLE(n) (AT91_SMC + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ -+#define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */ -+#define AT91_SMC_NWECYCLE_(x) ((x) << 0) -+#define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */ -+#define AT91_SMC_NRDCYCLE_(x) ((x) << 16) -+ -+#define AT91_SMC_MODE(n) (AT91_SMC + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ -+#define AT91_SMC_READMODE (1 << 0) /* Read Mode */ -+#define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */ -+#define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */ -+#define AT91_SMC_EXNWMODE_DISABLE (0 << 4) -+#define AT91_SMC_EXNWMODE_FROZEN (2 << 4) -+#define AT91_SMC_EXNWMODE_READY (3 << 4) -+#define AT91_SMC_BAT (1 << 8) /* Byte Access Type */ -+#define AT91_SMC_BAT_SELECT (0 << 8) -+#define AT91_SMC_BAT_WRITE (1 << 8) -+#define AT91_SMC_DBW (3 << 12) /* Data Bus Width */ -+#define AT91_SMC_DBW_8 (0 << 12) -+#define AT91_SMC_DBW_16 (1 << 12) -+#define AT91_SMC_DBW_32 (2 << 12) -+#define AT91_SMC_TDF (0xf << 16) /* Data Float Time. */ -+#define AT91_SMC_TDF_(x) ((x) << 16) -+#define AT91_SMC_TDFMODE (1 << 20) /* TDF Optimization - Enabled */ -+#define AT91_SMC_PMEN (1 << 24) /* Page Mode Enabled */ -+#define AT91_SMC_PS (3 << 28) /* Page Size */ -+#define AT91_SMC_PS_4 (0 << 28) -+#define AT91_SMC_PS_8 (1 << 28) -+#define AT91_SMC_PS_16 (2 << 28) -+#define AT91_SMC_PS_32 (3 << 28) -+ -+#if defined(AT91_SMC1) /* The AT91SAM9263 has 2 Static Memory contollers */ -+#define AT91_SMC1_SETUP(n) (AT91_SMC1 + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ -+#define AT91_SMC1_PULSE(n) (AT91_SMC1 + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ -+#define AT91_SMC1_CYCLE(n) (AT91_SMC1 + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ -+#define AT91_SMC1_MODE(n) (AT91_SMC1 + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ -+#endif -+ -+#endif ---- a/include/asm-arm/arch-at91/at91sam9rl.h -+++ b/include/asm-arm/arch-at91/at91sam9rl.h -@@ -110,6 +110,6 @@ - #define AT91SAM9RL_ROM_SIZE (2 * SZ_16K) /* Internal ROM size (32Kb) */ - - #define AT91SAM9RL_LCDC_BASE 0x00500000 /* LCD Controller */ --#define AT91SAM9RL_UDPHS_BASE 0x00600000 /* USB Device HS controller */ -+#define AT91SAM9RL_UDPHS_FIFO 0x00600000 /* USB Device HS controller */ - - #endif ---- a/include/asm-arm/arch-at91/board.h -+++ b/include/asm-arm/arch-at91/board.h -@@ -36,6 +36,7 @@ - #include <linux/i2c.h> - #include <linux/leds.h> - #include <linux/spi/spi.h> -+#include <linux/usb/atmel_usba_udc.h> - - /* USB Device */ - struct at91_udc_data { -@@ -45,6 +46,9 @@ struct at91_udc_data { - }; - extern void __init at91_add_device_udc(struct at91_udc_data *data); - -+ /* USB High Speed Device */ -+extern void __init at91_add_device_usba(struct usba_platform_data *data); -+ - /* Compact Flash */ - struct at91_cf_data { - u8 irq_pin; /* I/O IRQ */ -@@ -158,6 +162,9 @@ extern void __init at91_add_device_ac97( - /* ISI */ - extern void __init at91_add_device_isi(void); - -+ /* Touchscreen Controller */ -+extern void __init at91_add_device_tsadcc(void); -+ - /* LEDs */ - extern void __init at91_init_leds(u8 cpu_led, u8 timer_led); - extern void __init at91_gpio_leds(struct gpio_led *leds, int nr); ---- a/include/asm-arm/arch-at91/cpu.h -+++ b/include/asm-arm/arch-at91/cpu.h -@@ -48,6 +48,17 @@ static inline unsigned long at91_arch_id - return (at91_sys_read(AT91_DBGU_CIDR) & AT91_CIDR_ARCH); - } - -+#ifdef CONFIG_ARCH_AT91CAP9 -+#include <asm/arch/at91_pmc.h> -+ -+#define ARCH_REVISION_CAP9_B 0x399 -+#define ARCH_REVISION_CAP9_C 0x601 -+ -+static inline unsigned long at91cap9_rev_identify(void) -+{ -+ return (at91_sys_read(AT91_PMC_VER)); -+} -+#endif - - #ifdef CONFIG_ARCH_AT91RM9200 - #define cpu_is_at91rm9200() (at91_cpu_identify() == ARCH_ID_AT91RM9200) -@@ -83,8 +94,12 @@ static inline unsigned long at91_arch_id - - #ifdef CONFIG_ARCH_AT91CAP9 - #define cpu_is_at91cap9() (at91_cpu_identify() == ARCH_ID_AT91CAP9) -+#define cpu_is_at91cap9_revB() (at91cap9_rev_identify() == ARCH_REVISION_CAP9_B) -+#define cpu_is_at91cap9_revC() (at91cap9_rev_identify() == ARCH_REVISION_CAP9_C) - #else - #define cpu_is_at91cap9() (0) -+#define cpu_is_at91cap9_revB() (0) -+#define cpu_is_at91cap9_revC() (0) - #endif - - /* ---- /dev/null -+++ b/include/asm-arm/arch-at91/ics1523.h -@@ -0,0 +1,154 @@ -+//*---------------------------------------------------------------------------- -+//* ATMEL Microcontroller Software Support - ROUSSET - -+//*---------------------------------------------------------------------------- -+//* The software is delivered "AS IS" without warranty or condition of any -+//* kind, either express, implied or statutory. This includes without -+//* limitation any warranty or condition with respect to merchantability or -+//* fitness for any particular purpose, or against the infringements of -+//* intellectual property rights of others. -+//*---------------------------------------------------------------------------- -+//* File Name : ics1523.h -+//* Object : Clock Generator Prototyping File. -+//* -+//* 1.0 08/28/02 ED : Creation -+//* 1.2 13/01/03 FB : Update on lib V3 -+//*---------------------------------------------------------------------------- -+ -+#ifndef ics1523_h -+#define ics1523_h -+ -+/*-------------------------------------------*/ -+/* ICS1523 TWI Serial Clock Definition */ -+/*-------------------------------------------*/ -+ -+#define ICS_MIN_CLOCK 100 /* Min Frequency Access Clock KHz */ -+#define ICS_MAX_CLOCK 400 /* Max Frequency Access Clock KHz */ -+#define ICS_TRANSFER_RATE ICS_MAX_CLOCK /* Transfer speed to apply */ -+ -+#define ICS_WRITE_CLK_PNB 30 /* TWCK Clock Periods required to write */ -+#define ICS_READ_CLK_PNB 40 /* TWCK Clock Periods required to read */ -+ -+/*-------------------------------------------*/ -+/* ICS1523 Write Operation Definition */ -+/*-------------------------------------------*/ -+ -+#define ICS1523_ACCESS_OK 0 /* OK */ -+#define ICS1523_ACCESS_ERROR -1 /* NOK */ -+ -+/*-------------------------------------------*/ -+/* ICS1523 Device Addresses Definition */ -+/*-------------------------------------------*/ -+ -+#define ICS_ADDR 0x26 /* Device Address */ -+ -+/*--------------------------------------------------*/ -+/* ICS1523 Registers Internal Addresses Definition */ -+/*--------------------------------------------------*/ -+ -+#define ICS_ICR 0x0 /* Input Control Register */ -+#define ICS_LCR 0x1 /* Loop Control Register */ -+#define ICS_FD0 0x2 /* PLL FeedBack Divider LSBs */ -+#define ICS_FD1 0x3 /* PLL FeedBack Divider MSBs */ -+#define ICS_DPAO 0x4 /* Dynamic Phase Aligner Offset */ -+#define ICS_DPAC 0x5 /* Dynamic Phase Aligner Resolution */ -+#define ICS_OE 0x6 /* Output Enables Register */ -+#define ICS_OD 0x7 /* Osc Divider Register */ -+#define ICS_SWRST 0x8 /* DPA & PLL Reset Register */ -+#define ICS_VID 0x10 /* Chip Version Register */ -+#define ICS_RID 0x11 /* Chip Revision Register */ -+#define ICS_SR 0x12 /* Status Register */ -+ -+/*------------------------------------------------------*/ -+/* ICS1523 Input Control Register Bits Definition */ -+/*------------------------------------------------------*/ -+ -+#define ICS_PDEN 0x1 /* Phase Detector Enable */ -+#define ICS_PDPOL 0x2 /* Phase Detector Enable Polarity */ -+#define ICS_REFPOL 0x4 /* External Reference Polarity */ -+#define ICS_FBKPOL 0x8 /* External Feedback Polarity */ -+#define ICS_FBKSEL 0x10 /* External Feedback Select */ -+#define ICS_FUNCSEL 0x20 /* Function Out Select */ -+#define ICS_ENPLS 0x40 /* Enable PLL Lock/Ref Status Output */ -+#define ICS_ENDLS 0x80 /* Enable DPA Lock/Ref Status Output */ -+ -+/*-----------------------------------------------------*/ -+/* ICS1523 Loop Control Register Bits Definition */ -+/*-----------------------------------------------------*/ -+ -+#define ICS_PFD 0x7 /* Phase Detector Gain */ -+#define ICS_PSD 0x30 /* Post-Scaler Divider */ -+ -+/*----------------------------------------------------*/ -+/* ICS1523 PLL FeedBack Divider LSBs Definition */ -+/*----------------------------------------------------*/ -+ -+#define ICS_FBDL 0xFF /* PLL FeedBack Divider LSBs */ -+ -+/*----------------------------------------------------*/ -+/* ICS1523 PLL FeedBack Divider MSBs Definition */ -+/*----------------------------------------------------*/ -+ -+#define ICS_FBDM 0xF /* PLL FeedBack Divider MSBs */ -+ -+/*------------------------------------------------------------*/ -+/* ICS1523 Dynamic Phase Aligner Offset Bits Definition */ -+/*------------------------------------------------------------*/ -+ -+#define ICS_DPAOS 0x2F /* Dynamic Phase Aligner Offset */ -+#define ICS_FILSEL 0x80 /* Loop Filter Select */ -+ -+/*----------------------------------------------------------------*/ -+/* ICS1523 Dynamic Phase Aligner Resolution Bits Definition */ -+/*----------------------------------------------------------------*/ -+ -+#define ICS_DPARES 0x3 /* Dynamic Phase Aligner Resolution */ -+#define ICS_MMREV 0xFC /* Metal Mask Revision Number */ -+ -+/*-------------------------------------------------------*/ -+/* ICS1523 Output Enables Register Bits Definition */ -+/*-------------------------------------------------------*/ -+ -+#define ICS_OEPCK 0x1 /* Output Enable for PECL PCLK Outputs */ -+#define ICS_OETCK 0x2 /* Output Enable for STTL CLK Output */ -+#define ICS_OEP2 0x4 /* Output Enable for PECL CLK/2 Outputs */ -+#define ICS_OET2 0x8 /* Output Enable for STTL CLK/2 Output */ -+#define ICS_OEF 0x10 /* Output Enable for STTL FUNC Output */ -+#define ICS_CLK2INV 0x20 /* CLK/2 Invert */ -+#define ICS_OSCL 0xC0 /* SSTL Clock Scaler */ -+ -+/*----------------------------------------------------*/ -+/* ICS1523 Osc Divider Register Bits Definition */ -+/*----------------------------------------------------*/ -+ -+#define ICS_OSCDIV 0x7F /* Oscillator Divider Modulus */ -+#define ICS_INSEL 0x80 /* Input Select */ -+ -+/*---------------------------------------------------*/ -+/* ICS1523 DPA & PLL Reset Register Definition */ -+/*---------------------------------------------------*/ -+ -+#define ICS_DPAR 0x0A /* DPA Reset Command */ -+#define ICS_PLLR 0x50 /* PLL Reset Command */ -+ -+/*------------------------------------------------*/ -+/* ICS1523 Chip Version Register Definition */ -+/*------------------------------------------------*/ -+ -+#define ICS_CHIPV 0xFF /* Chip Version */ -+ -+/*-------------------------------------------------*/ -+/* ICS1523 Chip Revision Register Definition */ -+/*-------------------------------------------------*/ -+ -+#define ICS_CHIPR 0xFF /* Chip Revision */ -+ -+/*------------------------------------------*/ -+/* ICS1523 Status Register Definition */ -+/*------------------------------------------*/ -+ -+#define ICS_DPALOCK 0x1 /* DPA Lock Status */ -+#define ICS_PLLLOCK 0x2 /* PLL Lock Status */ -+ -+int at91_ics1523_init(void); -+ -+#endif /* ics1523_h */ ---- /dev/null -+++ b/include/asm-arm/arch-at91/spi.h -@@ -0,0 +1,54 @@ -+/* -+ * Serial Peripheral Interface (SPI) driver for the Atmel AT91RM9200 -+ * -+ * (c) SAN People (Pty) Ltd -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version -+ * 2 of the License, or (at your option) any later version. -+ */ -+ -+#ifndef AT91_LEGACY_SPI_H -+#define AT91_LEGACY_SPI_H -+ -+#define SPI_MAJOR 153 /* registered device number */ -+ -+#define DEFAULT_SPI_CLK 6000000 -+ -+ -+/* Maximum number of buffers in a single SPI transfer. -+ * DataFlash uses maximum of 2 -+ * spidev interface supports up to 8. -+ */ -+#define MAX_SPI_TRANSFERS 8 -+#define NR_SPI_DEVICES 4 /* number of devices on SPI bus */ -+ -+/* -+ * Describes the buffers for a SPI transfer. -+ * A transmit & receive buffer must be specified for each transfer -+ */ -+struct spi_transfer_list { -+ void* tx[MAX_SPI_TRANSFERS]; /* transmit */ -+ int txlen[MAX_SPI_TRANSFERS]; -+ void* rx[MAX_SPI_TRANSFERS]; /* receive */ -+ int rxlen[MAX_SPI_TRANSFERS]; -+ int nr_transfers; /* number of transfers */ -+ int curr; /* current transfer */ -+}; -+ -+struct spi_local { -+ unsigned int pcs; /* Peripheral Chip Select value */ -+ -+ struct spi_transfer_list *xfers; /* current transfer list */ -+ dma_addr_t tx, rx; /* DMA address for current transfer */ -+ dma_addr_t txnext, rxnext; /* DMA address for next transfer */ -+}; -+ -+ -+/* Exported functions */ -+extern void spi_access_bus(short device); -+extern void spi_release_bus(short device); -+extern int spi_transfer(struct spi_transfer_list* list); -+ -+#endif ---- a/include/asm-arm/arch-at91/timex.h -+++ b/include/asm-arm/arch-at91/timex.h -@@ -27,14 +27,29 @@ - - #define CLOCK_TICK_RATE (AT91_SLOW_CLOCK) - --#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9261) -+#elif defined(CONFIG_ARCH_AT91SAM9260) -+ -+#if defined(CONFIG_MACH_USB_A9260) || defined(CONFIG_MACH_QIL_A9260) -+#define AT91SAM9_MASTER_CLOCK 90000000 -+#else -+#define AT91SAM9_MASTER_CLOCK 99300000 -+#endif -+ -+#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) -+ -+#elif defined(CONFIG_ARCH_AT91SAM9261) - - #define AT91SAM9_MASTER_CLOCK 99300000 - #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - - #elif defined(CONFIG_ARCH_AT91SAM9263) - -+#if defined(CONFIG_MACH_USB_A9263) -+#define AT91SAM9_MASTER_CLOCK 90000000 -+#else - #define AT91SAM9_MASTER_CLOCK 99959500 -+#endif -+ - #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - - #elif defined(CONFIG_ARCH_AT91SAM9RL) ---- a/include/asm-arm/arch-ks8695/devices.h -+++ b/include/asm-arm/arch-ks8695/devices.h -@@ -18,6 +18,11 @@ extern void __init ks8695_add_device_wan - extern void __init ks8695_add_device_lan(void); - extern void __init ks8695_add_device_hpna(void); - -+ /* LEDs */ -+extern short ks8695_leds_cpu; -+extern short ks8695_leds_timer; -+extern void __init ks8695_init_leds(u8 cpu_led, u8 timer_led); -+ - /* PCI */ - #define KS8695_MODE_PCI 0 - #define KS8695_MODE_MINIPCI 1 ---- a/include/linux/clk.h -+++ b/include/linux/clk.h -@@ -121,4 +121,24 @@ int clk_set_parent(struct clk *clk, stru - */ - struct clk *clk_get_parent(struct clk *clk); - -+/** -+ * clk_must_disable - report whether a clock's users must disable it -+ * @clk: one node in the clock tree -+ * -+ * This routine returns true only if the upcoming system state requires -+ * disabling the specified clock. -+ * -+ * It's common for platform power states to constrain certain clocks (and -+ * their descendants) to be unavailable, while other states allow that -+ * clock to be active. A platform's power states often include an "all on" -+ * mode; system wide sleep states like "standby" or "suspend-to-RAM"; and -+ * operating states which sacrifice functionality for lower power usage. -+ * -+ * The constraint value is commonly tested in device driver suspend(), to -+ * leave clocks active if they are needed for features like wakeup events. -+ * On platforms that support reduced functionality operating states, the -+ * constraint may also need to be tested during resume() and probe() calls. -+ */ -+int clk_must_disable(struct clk *clk); -+ - #endif ---- a/include/linux/i2c-id.h -+++ b/include/linux/i2c-id.h -@@ -131,6 +131,7 @@ - - /* --- PCA 9564 based algorithms */ - #define I2C_HW_A_ISA 0x1a0000 /* generic ISA Bus interface card */ -+#define I2C_HW_A_PLAT 0x1a0001 /* generic platform_bus interface */ - - /* --- PowerPC on-chip adapters */ - #define I2C_HW_OCP 0x120000 /* IBM on-chip I2C adapter */ ---- /dev/null -+++ b/include/linux/usb/atmel_usba_udc.h -@@ -0,0 +1,23 @@ -+/* -+* Platform data definitions for Atmel USBA gadget driver. -+*/ -+#ifndef __LINUX_USB_USBA_H -+#define __LINUX_USB_USBA_H -+ -+struct usba_ep_data { -+ char* name; -+ int index; -+ int fifo_size; -+ int nr_banks; -+ int can_dma; -+ int can_isoc; -+}; -+ -+struct usba_platform_data { -+ int vbus_pin; -+ int num_ep; -+ struct usba_ep_data ep[0]; -+}; -+ -+#endif /* __LINUX_USB_USBA_H */ -+ ---- a/include/video/atmel_lcdc.h -+++ b/include/video/atmel_lcdc.h -@@ -39,6 +39,7 @@ struct atmel_lcdfb_info { - u8 bl_power; - #endif - bool lcdcon_is_backlight; -+ u8 saved_lcdcon; - - u8 default_bpp; - unsigned int default_lcdcon2; ---- a/sound/soc/at91/eti_b1_wm8731.c -+++ b/sound/soc/at91/eti_b1_wm8731.c -@@ -33,8 +33,7 @@ - #include <sound/soc.h> - #include <sound/soc-dapm.h> - --#include <asm/arch/hardware.h> --#include <asm/arch/at91_pio.h> -+#include <asm/hardware.h> - #include <asm/arch/gpio.h> - - #include "../codecs/wm8731.h" -@@ -47,13 +46,6 @@ - #define DBG(x...) - #endif - --#define AT91_PIO_TF1 (1 << (AT91_PIN_PB6 - PIN_BASE) % 32) --#define AT91_PIO_TK1 (1 << (AT91_PIN_PB7 - PIN_BASE) % 32) --#define AT91_PIO_TD1 (1 << (AT91_PIN_PB8 - PIN_BASE) % 32) --#define AT91_PIO_RD1 (1 << (AT91_PIN_PB9 - PIN_BASE) % 32) --#define AT91_PIO_RK1 (1 << (AT91_PIN_PB10 - PIN_BASE) % 32) --#define AT91_PIO_RF1 (1 << (AT91_PIN_PB11 - PIN_BASE) % 32) -- - static struct clk *pck1_clk; - static struct clk *pllb_clk; - -@@ -276,7 +268,6 @@ static struct platform_device *eti_b1_sn - static int __init eti_b1_init(void) - { - int ret; -- u32 ssc_pio_lines; - struct at91_ssc_periph *ssc = eti_b1_dai.cpu_dai->private_data; - - if (!request_mem_region(AT91RM9200_BASE_SSC1, SZ_16K, "soc-audio")) { -@@ -310,19 +301,12 @@ static int __init eti_b1_init(void) - goto fail_io_unmap; - } - -- ssc_pio_lines = AT91_PIO_TF1 | AT91_PIO_TK1 | AT91_PIO_TD1 -- | AT91_PIO_RD1 /* | AT91_PIO_RK1 */ | AT91_PIO_RF1; -- -- /* Reset all PIO registers and assign lines to peripheral A */ -- at91_sys_write(AT91_PIOB + PIO_PDR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_ODR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_IFDR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_CODR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_IDR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_MDDR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_PUDR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_ASR, ssc_pio_lines); -- at91_sys_write(AT91_PIOB + PIO_OWDR, ssc_pio_lines); -+ at91_set_A_periph(AT91_PIN_PB6, 0); /* TF1 */ -+ at91_set_A_periph(AT91_PIN_PB7, 0); /* TK1 */ -+ at91_set_A_periph(AT91_PIN_PB8, 0); /* TD1 */ -+ at91_set_A_periph(AT91_PIN_PB9, 0); /* RD1 */ -+/* at91_set_A_periph(AT91_PIN_PB10, 0);*/ /* RK1 */ -+ at91_set_A_periph(AT91_PIN_PB11, 0); /* RF1 */ - - /* - * Set PCK1 parent to PLLB and its rate to 12 Mhz. ---- a/sound/spi/at73c213.c -+++ b/sound/spi/at73c213.c -@@ -114,7 +114,11 @@ snd_at73c213_write_reg(struct snd_at73c2 - static struct snd_pcm_hardware snd_at73c213_playback_hw = { - .info = SNDRV_PCM_INFO_INTERLEAVED | - SNDRV_PCM_INFO_BLOCK_TRANSFER, -+#ifdef __BIG_ENDIAN - .formats = SNDRV_PCM_FMTBIT_S16_BE, -+#else -+ .formats = SNDRV_PCM_FMTBIT_S16_LE, -+#endif - .rates = SNDRV_PCM_RATE_CONTINUOUS, - .rate_min = 8000, /* Replaced by chip->bitrate later. */ - .rate_max = 50000, /* Replaced by chip->bitrate later. */ diff --git a/target/linux/at91/patches-2.6.25/001-vlink-machine.patch b/target/linux/at91/patches-2.6.25/001-vlink-machine.patch deleted file mode 100644 index 76e3698c52..0000000000 --- a/target/linux/at91/patches-2.6.25/001-vlink-machine.patch +++ /dev/null @@ -1,229 +0,0 @@ ---- a/arch/arm/mach-at91/Kconfig -+++ b/arch/arm/mach-at91/Kconfig -@@ -151,6 +151,12 @@ config MACH_TT9200 - help - Select this if you are using Toptech's TT9200 board. - -+config MACH_VLINK -+ bool "Figment Design Labs VersaLink" -+ depends on ARCH_AT91RM9200 -+ help -+ Select this if you are using FDL's VersaLink board -+ - endif - - # ---------------------------------------------------------- ---- a/arch/arm/mach-at91/Makefile -+++ b/arch/arm/mach-at91/Makefile -@@ -29,6 +29,7 @@ obj-$(CONFIG_MACH_KB9200) += board-kb920 - obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o - obj-$(CONFIG_MACH_KAFA) += board-kafa.o - obj-$(CONFIG_MACH_CHUB) += board-chub.o -+obj-$(CONFIG_MACH_VLINK) += board-vlink.o - obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o - obj-$(CONFIG_MACH_HOMEMATIC) += board-homematic.o - obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o ---- /dev/null -+++ b/arch/arm/mach-at91/board-vlink.c -@@ -0,0 +1,201 @@ -+/* -+ * linux/arch/arm/mach-at91/board-vlink.c -+ * -+ * Copyright (C) 2005 SAN People -+ * Copyright (C) 2006,2007 Guthrie Consulting -+ * -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/types.h> -+#include <linux/init.h> -+#include <linux/mm.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/spi/spi.h> -+#include <linux/mtd/physmap.h> -+ -+#include <asm/hardware.h> -+#include <asm/setup.h> -+#include <asm/mach-types.h> -+#include <asm/irq.h> -+ -+#include <asm/mach/arch.h> -+#include <asm/mach/map.h> -+#include <asm/mach/irq.h> -+ -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/at91rm9200_mc.h> -+ -+#include "generic.h" -+ -+ -+static void __init vlink_map_io(void) -+{ -+ /* Initialize processor: 18.432 MHz crystal */ -+ at91rm9200_initialize(18432000, AT91RM9200_PQFP); -+ -+ /* Setup the LEDs */ -+ at91_init_leds(AT91_PIN_PC14, AT91_PIN_PC15); -+ -+ /* Setup serial ports */ -+ -+ /* DBGU on ttyS0. (RX and TX only) */ -+ at91_register_uart(0, 0, 0); -+ -+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DSR, DTR, DCD, RI) */ -+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS -+ | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR -+ | ATMEL_UART_DCD | ATMEL_UART_RI); -+ -+ /* USART0 on ttys2. (Rx, Tx, CTS, RTS, DTR, DCD, RI) */ -+ at91_register_uart(AT91RM9200_ID_US0, 2, ATMEL_UART_CTS -+ | ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI); -+ -+ /* USART3 on ttyS3. (Rx, Tx, CTS, RTS, DTR, DCD, RI) */ -+ at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS -+ | ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI); -+ -+ /* USART2 on ttyS4. (Rx and Tx only) */ -+ at91_register_uart(AT91RM9200_ID_US2, 4, 0); -+ -+ /* Console on ttyS0 (ie DBGU) */ -+ at91_set_serial_console(0); -+} -+ -+static void __init vlink_init_irq(void) -+{ -+ at91rm9200_init_interrupts(NULL); -+} -+ -+static struct at91_eth_data __initdata vlink_eth_data = { -+ .phy_irq_pin = AT91_PIN_PC4, -+ .is_rmii = 1, -+}; -+ -+static struct at91_usbh_data __initdata vlink_usbh_data = { -+ .ports = 1, -+}; -+ -+/* -+static struct at91_udc_data __initdata vlink_udc_data = { -+ .vbus_pin = AT91_PIN_PD4, -+ .pullup_pin = AT91_PIN_PD5, -+}; -+*/ -+ -+static struct at91_mmc_data __initdata vlink_mmc_data = { -+// .det_pin = AT91_PIN_PB27, -+ .slot_b = 0, -+ .wire4 = 1, -+// .wp_pin = AT91_PIN_PA17, -+}; -+ -+static struct spi_board_info vlink_spi_devices[] = { -+ { /* DataFlash chip */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 0, -+ .max_speed_hz = 15 * 1000 * 1000, -+ }, -+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD -+ { /* DataFlash card */ -+ .modalias = "mtd_dataflash", -+ .chip_select = 3, -+ .max_speed_hz = 15 * 1000 * 1000, -+ }, -+#endif -+}; -+ -+/*static struct at91_gpio_led vlink_leds[] = { -+ { -+ .name = "led0", -+ .gpio = AT91_PIN_PC14, -+ .trigger = "heartbeat", -+ }, -+ { -+ .name = "led1", -+ .gpio = AT91_PIN_PC15, -+ .trigger = "timer", -+ } -+}; -+*/ -+ -+static void __init vlink_board_init(void) -+{ -+ /* Serial */ -+ at91_add_device_serial(); -+ /* Ethernet */ -+ at91_add_device_eth(&vlink_eth_data); -+ /* USB Host */ -+ at91_add_device_usbh(&vlink_usbh_data); -+ /* USB Device */ -+// at91_add_device_udc(&vlink_udc_data); -+// at91_set_multi_drive(vlink_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ -+ /* I2C */ -+// at91_add_device_i2c(); -+ /* SPI */ -+ at91_add_device_spi(vlink_spi_devices, ARRAY_SIZE(vlink_spi_devices)); -+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD -+ /* DataFlash card */ -+// at91_set_gpio_output(AT91_PIN_PB22, 0); -+#else -+ /* MMC */ -+// at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ -+ at91_add_device_mmc(0, &vlink_mmc_data); -+#endif -+ /* LEDs */ -+// at91_gpio_leds(vlink_leds, ARRAY_SIZE(vlink_leds)); -+ -+/* Other LED's */ -+ at91_set_gpio_output(AT91_PIN_PC7, 1); // LED FRONT AP1 -+ at91_set_gpio_output(AT91_PIN_PC8, 1); // LED FRONT BP1 -+ at91_set_gpio_output(AT91_PIN_PB14, 1); // LED BACK AP1 -+ at91_set_gpio_output(AT91_PIN_PB15, 1); // LED BACK BP1 -+ at91_set_gpio_output(AT91_PIN_PB16, 1); // LED BACK AP2 -+ at91_set_gpio_output(AT91_PIN_PB17, 1); // LED BACK BP2 -+ -+/* SIM Cards */ -+ at91_set_gpio_output(AT91_PIN_PB9, 1); // ENBSC3 -+ at91_set_gpio_output(AT91_PIN_PB10, 1); // ENBSC2 -+ at91_set_gpio_output(AT91_PIN_PB11, 1); // ENBSC1 -+ -+/* GSM Module Control */ -+ at91_set_gpio_output(AT91_PIN_PB12, 1); // GSMONOFF -+ -+/* Test jig presence detection */ -+ at91_set_gpio_input(AT91_PIN_PB8, 1); // JIGPRESENT -+ -+/* Power indicator */ -+ at91_set_gpio_input(AT91_PIN_PB22, 1); // PWR_IND -+ -+/* USB Device control */ -+ at91_set_gpio_input(AT91_PIN_PB27, 1); // UDB_CNX -+ at91_set_gpio_output(AT91_PIN_PB28, 1); // UDB_PUP -+ at91_set_multi_drive(AT91_PIN_PB28, 1); // Set to multi-drive -+ -+} -+ -+MACHINE_START(VLINK, "FDL VersaLink") -+ /* Maintainer: Guthrie Consulting */ -+ .phys_io = AT91_BASE_SYS, -+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -+ .boot_params = AT91_SDRAM_BASE + 0x100, -+ .timer = &at91rm9200_timer, -+ .map_io = vlink_map_io, -+ .init_irq = vlink_init_irq, -+ .init_machine = vlink_board_init, -+MACHINE_END diff --git a/target/linux/at91/patches-2.6.25/002-led-driver.patch b/target/linux/at91/patches-2.6.25/002-led-driver.patch deleted file mode 100644 index 595720dcb2..0000000000 --- a/target/linux/at91/patches-2.6.25/002-led-driver.patch +++ /dev/null @@ -1,167 +0,0 @@ ---- a/arch/arm/mach-at91/at91rm9200_devices.c -+++ b/arch/arm/mach-at91/at91rm9200_devices.c -@@ -717,6 +717,26 @@ static void __init at91_add_device_watch - static void __init at91_add_device_watchdog(void) {} - #endif - -+/* -------------------------------------------------------------------- -+ * LEDs -+ * -------------------------------------------------------------------- */ -+ -+#if defined(CONFIG_LEDS) -+u8 at91_leds_cpu; -+u8 at91_leds_timer; -+ -+void __init at91_init_leds(u8 cpu_led, u8 timer_led) -+{ -+ /* Enable GPIO to access the LEDs */ -+ at91_set_gpio_output(cpu_led, 1); -+ at91_set_gpio_output(timer_led, 1); -+ -+ at91_leds_cpu = cpu_led; -+ at91_leds_timer = timer_led; -+} -+#else -+void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} -+#endif - - /* -------------------------------------------------------------------- - * SSC -- Synchronous Serial Controller ---- a/arch/arm/mach-at91/Makefile -+++ b/arch/arm/mach-at91/Makefile -@@ -60,7 +60,12 @@ obj-$(CONFIG_MACH_AT91CAP9ADK) += board- - obj-$(CONFIG_MACH_AT91EB01) += board-eb01.o - - # Drivers --obj-y += leds.o -+ifeq ($(CONFIG_MACH_VLINK),y) -+led-$(CONFIG_MACH_VLINK) += vlink_leds.o -+else -+led-y += leds.o -+endif -+obj-y += $(led-y) - obj-$(CONFIG_FB_S1D13XXX) += ics1523.o - - # Power Management ---- /dev/null -+++ b/arch/arm/mach-at91/vlink_leds.c -@@ -0,0 +1,105 @@ -+/* -+ * LED driver for Atmel AT91-based boards. -+ * -+ * Copyright (C) SAN People (Pty) Ltd -+ * Modified for FDL VersaLink Copyright (C) Guthrie Consulting -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * as published by the Free Software Foundation; either version -+ * 2 of the License, or (at your option) any later version. -+*/ -+ -+#include <linux/kernel.h> -+#include <linux/module.h> -+#include <linux/init.h> -+ -+#include <asm/mach-types.h> -+#include <asm/leds.h> -+#include <asm/arch/board.h> -+#include <asm/arch/gpio.h> -+ -+ -+static inline void at91_led_on(unsigned int led) -+{ -+ at91_set_gpio_value(led, 0); -+} -+ -+static inline void at91_led_off(unsigned int led) -+{ -+ at91_set_gpio_value(led, 1); -+} -+ -+static inline void at91_led_toggle(unsigned int led) -+{ -+ unsigned long is_off = at91_get_gpio_value(led); -+ if (is_off) { -+ at91_led_on(led); -+ at91_led_off(at91_leds_cpu); -+ } -+ else { -+ at91_led_on(at91_leds_cpu); -+ at91_led_off(led); -+ } -+} -+ -+ -+/* -+ * Handle LED events. -+ */ -+ -+/* -+ * VersaLink has a single bi-coloured LED which changes colour when the -+ * polarity is reversed -+ */ -+static void at91_leds_event(led_event_t evt) -+{ -+ unsigned long flags; -+ -+ local_irq_save(flags); -+ -+ switch(evt) { -+ case led_start: /* System startup */ -+ at91_led_toggle(at91_leds_timer); -+ break; -+ -+ case led_stop: /* System stop / suspend */ -+ at91_led_toggle(at91_leds_timer); -+ break; -+ -+#ifdef CONFIG_LEDS_TIMER -+ case led_timer: /* Every 50 timer ticks */ -+ at91_led_toggle(at91_leds_timer); -+ break; -+#endif -+ -+#ifdef CONFIG_LEDS_CPU -+ case led_idle_start: /* Entering idle state */ -+ at91_led_toggle(at91_leds_timer); -+ break; -+ -+ case led_idle_end: /* Exit idle state */ -+ at91_led_toggle(at91_leds_timer); -+ break; -+#endif -+ -+ default: -+ break; -+ } -+ -+ local_irq_restore(flags); -+} -+ -+ -+static int __init leds_init(void) -+{ -+ if (!at91_leds_timer || !at91_leds_cpu) -+ return -ENODEV; -+ -+ leds_event = at91_leds_event; -+ -+ leds_event(led_start); -+ return 0; -+} -+ -+__initcall(leds_init); ---- a/include/asm-arm/arch-at91/board.h -+++ b/include/asm-arm/arch-at91/board.h -@@ -162,6 +162,11 @@ extern void __init at91_add_device_ac97( - /* ISI */ - extern void __init at91_add_device_isi(void); - -+ /* LEDs */ -+extern u8 at91_leds_cpu; -+extern u8 at91_leds_timer; -+extern void __init at91_init_leds(u8 cpu_led, u8 timer_led); -+ - /* Touchscreen Controller */ - extern void __init at91_add_device_tsadcc(void); - diff --git a/target/linux/at91/patches-2.6.25/003-gpio-driver.patch b/target/linux/at91/patches-2.6.25/003-gpio-driver.patch deleted file mode 100644 index 3968c6b2d5..0000000000 --- a/target/linux/at91/patches-2.6.25/003-gpio-driver.patch +++ /dev/null @@ -1,546 +0,0 @@ ---- a/arch/arm/mach-at91/board-vlink.c -+++ b/arch/arm/mach-at91/board-vlink.c -@@ -99,7 +99,7 @@ static struct at91_udc_data __initdata v - */ - - static struct at91_mmc_data __initdata vlink_mmc_data = { --// .det_pin = AT91_PIN_PB27, -+// .det_pin = AT91_PIN_PC10, - .slot_b = 0, - .wire4 = 1, - // .wp_pin = AT91_PIN_PA17, -@@ -136,6 +136,7 @@ static struct spi_board_info vlink_spi_d - - static void __init vlink_board_init(void) - { -+ int v100; - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ -@@ -157,36 +158,66 @@ static void __init vlink_board_init(void - // at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mmc(0, &vlink_mmc_data); - #endif -+ -+// Set VLink version PIN as an input with pull-up (V1.5 = GND) -+ at91_set_gpio_input(AT91_PIN_PC2, 1); -+ v100 = at91_get_gpio_value(AT91_PIN_PC2); -+ - /* LEDs */ - // at91_gpio_leds(vlink_leds, ARRAY_SIZE(vlink_leds)); - - /* Other LED's */ -- at91_set_gpio_output(AT91_PIN_PC7, 1); // LED FRONT AP1 -- at91_set_gpio_output(AT91_PIN_PC8, 1); // LED FRONT BP1 -- at91_set_gpio_output(AT91_PIN_PB14, 1); // LED BACK AP1 -- at91_set_gpio_output(AT91_PIN_PB15, 1); // LED BACK BP1 -- at91_set_gpio_output(AT91_PIN_PB16, 1); // LED BACK AP2 -- at91_set_gpio_output(AT91_PIN_PB17, 1); // LED BACK BP2 -+ at91_set_gpio_output(AT91_PIN_PC7, 1); // LED FRONT AP1 -+ at91_set_gpio_output(AT91_PIN_PC8, 1); // LED FRONT BP1 -+ at91_set_gpio_output(AT91_PIN_PB14, 1); // LED BACK AP1 -+ at91_set_gpio_output(AT91_PIN_PB15, 1); // LED BACK BP1 -+ at91_set_gpio_output(AT91_PIN_PB16, 1); // LED BACK AP2 -+ at91_set_gpio_output(AT91_PIN_PB17, 1); // LED BACK BP2 -+ -+/* Test jig presence detection */ -+ at91_set_gpio_input(AT91_PIN_PB8, 1); // JIGPRESENT - - /* SIM Cards */ -- at91_set_gpio_output(AT91_PIN_PB9, 1); // ENBSC3 -- at91_set_gpio_output(AT91_PIN_PB10, 1); // ENBSC2 -- at91_set_gpio_output(AT91_PIN_PB11, 1); // ENBSC1 -+ if (at91_get_gpio_value(AT91_PIN_PB8)) { -+ at91_set_gpio_output(AT91_PIN_PB11, 0); -+ if (v100) -+ at91_set_gpio_output(AT91_PIN_PB9, 1); -+ else -+ at91_set_gpio_output(AT91_PIN_PC13, 1); -+ } else { -+ at91_set_gpio_output(AT91_PIN_PB11, 1); -+ if (v100) -+ at91_set_gpio_output(AT91_PIN_PB9, 0); -+ else -+ at91_set_gpio_output(AT91_PIN_PC13, 0); -+ } - --/* GSM Module Control */ -- at91_set_gpio_output(AT91_PIN_PB12, 1); // GSMONOFF -+ at91_set_gpio_output(AT91_PIN_PB10, 1); // ENBSC2 - --/* Test jig presence detection */ -- at91_set_gpio_input(AT91_PIN_PB8, 1); // JIGPRESENT -+/* GSM Module Control */ -+ at91_set_gpio_output(AT91_PIN_PB12, 1); // GSMONOFF - - /* Power indicator */ -- at91_set_gpio_input(AT91_PIN_PB22, 1); // PWR_IND -+ at91_set_gpio_input(AT91_PIN_PB22, 1); // PWR_IND - - /* USB Device control */ -- at91_set_gpio_input(AT91_PIN_PB27, 1); // UDB_CNX -- at91_set_gpio_output(AT91_PIN_PB28, 1); // UDB_PUP -- at91_set_multi_drive(AT91_PIN_PB28, 1); // Set to multi-drive -- -+ at91_set_gpio_input(AT91_PIN_PB27, 1); // UDB_CNX -+ at91_set_gpio_output(AT91_PIN_PB28, 1); // UDB_PUP -+ at91_set_multi_drive(AT91_PIN_PB28, 1); // Set to multi-drive -+ -+/* USB Power controls */ -+ -+ if (v100) -+ { // V100 -+ at91_set_gpio_input (AT91_PIN_PC12, 1); // SD Card present -+ } -+ else -+ { // DO special things for V1.5 -+ at91_set_gpio_output(AT91_PIN_PB9 , 0); // USB suspend -+ at91_set_gpio_input (AT91_PIN_PC10, 1); // SD Card present -+ at91_set_gpio_output(AT91_PIN_PC11, 0); // USB Vin CTRL for modules onboard -+ at91_set_gpio_output(AT91_PIN_PC12, 0); // SIM control -+ } - } - - MACHINE_START(VLINK, "FDL VersaLink") ---- a/arch/arm/mach-at91/gpio.c -+++ b/arch/arm/mach-at91/gpio.c -@@ -29,6 +29,7 @@ - - static struct at91_gpio_bank *gpio; - static int gpio_banks; -+static u32 pio_gpio_pin[4] = { 0, 0, 0, 0 }; - - - static inline void __iomem *pin_to_controller(unsigned pin) -@@ -71,9 +72,13 @@ int __init_or_module at91_set_GPIO_perip - { - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); -+ int bank = (pin - PIN_BASE) / 32; - - if (!pio) - return -EINVAL; -+ -+ pio_gpio_pin[bank] |= mask; -+ - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_PER); -@@ -130,10 +135,13 @@ int __init_or_module at91_set_gpio_input - { - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); -+ int bank = (pin - PIN_BASE) / 32; - - if (!pio) - return -EINVAL; - -+ pio_gpio_pin[bank] |= mask; -+ - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_ODR); -@@ -151,10 +159,13 @@ int __init_or_module at91_set_gpio_outpu - { - void __iomem *pio = pin_to_controller(pin); - unsigned mask = pin_to_mask(pin); -+ int bank = (pin - PIN_BASE) / 32; - - if (!pio) - return -EINVAL; - -+ pio_gpio_pin[bank] |= mask; -+ - __raw_writel(mask, pio + PIO_IDR); - __raw_writel(mask, pio + PIO_PUDR); - __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); -@@ -262,6 +273,18 @@ int at91_get_gpio_value(unsigned pin) - } - EXPORT_SYMBOL(at91_get_gpio_value); - -+int at91_is_pin_gpio(unsigned pin) -+{ -+ void __iomem *pio = pin_to_controller(pin); -+ unsigned mask = pin_to_mask(pin); -+ int bank = (pin - PIN_BASE) / 32; -+ -+ if (!pio) -+ return -EINVAL; -+ return (pio_gpio_pin[bank] & mask) != 0; -+} -+EXPORT_SYMBOL(at91_is_pin_gpio); -+ - /*--------------------------------------------------------------------------*/ - - #ifdef CONFIG_PM ---- a/drivers/char/Kconfig -+++ b/drivers/char/Kconfig -@@ -1072,5 +1072,12 @@ config AT91_SPIDEV - The SPI driver gives user mode access to this serial - bus on the AT91RM9200 processor. - -+config AT91_VLIO -+ tristate "Versalink LED and GPIO interface" -+ depends on ARCH_AT91RM9200 && MACH_VLINK -+ default n -+ help -+ Provides a handler GPIO's in userspace -+ - endmenu - ---- a/drivers/char/Makefile -+++ b/drivers/char/Makefile -@@ -100,6 +100,7 @@ obj-$(CONFIG_GPIO_TB0219) += tb0219.o - obj-$(CONFIG_TELCLOCK) += tlclk.o - obj-$(CONFIG_AT91_SPI) += at91_spi.o - obj-$(CONFIG_AT91_SPIDEV) += at91_spidev.o -+obj-$(CONFIG_AT91_VLIO) += vlink_giu.o - - obj-$(CONFIG_MWAVE) += mwave/ - obj-$(CONFIG_AGP) += agp/ ---- /dev/null -+++ b/drivers/char/vlink_giu.c -@@ -0,0 +1,333 @@ -+/* -+ * Driver for FDL Versalink GPIO -+ * -+ * Copyright (C) 2005 Guthrie Consulting -+ * Author: Hamish Guthrie <hamish@prodigi.ch> -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#include <linux/module.h> -+#include <linux/moduleparam.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+ -+#include <linux/kernel.h> -+#include <linux/slab.h> -+#include <linux/fs.h> -+#include <linux/errno.h> -+#include <linux/init.h> -+#include <linux/types.h> -+#include <linux/proc_fs.h> -+#include <linux/fcntl.h> -+#include <linux/seq_file.h> -+#include <linux/cdev.h> -+#include <asm/arch/gpio.h> -+#include <asm/uaccess.h> -+ -+static int major; /* default is dynamic major device number */ -+module_param(major, int, 0); -+MODULE_PARM_DESC(major, "Major device number"); -+ -+#define VIO_NR_DEVS 96 -+ -+struct vio_dev { -+ struct cdev cdev; -+}; -+ -+struct vio_dev *vio_devices; -+static struct class *vio_class; -+ -+#define MAX_VIO_NAMES 24 -+typedef struct -+{ -+ char port; -+ char pin; -+ char name100[10]; -+ char name150[10]; -+} VIO_NAMES; -+ -+VIO_NAMES VioName[MAX_VIO_NAMES] = -+{ // Port, Pin, V100, V150 -+ {'A',19,"port1DTR" ,"port1DTR"}, -+ {'A',24,"port2DTR" ,"port2DTR"}, -+ {'B',8, "jigOn" ,"jigOn"} , -+ {'B',9, "enbSC3" ,"usbSUSPND"}, -+ {'B',10,"enbSC2" ,"enbSC2"}, -+ {'B',11,"enbSC1" ,"enbSC1"}, -+ {'B',12,"gsmONOFF" ,"gsmONOFF"}, -+ {'B',14,"ledBAP1" ,"ledBAP1"}, -+ {'B',15,"ledBBP1" ,"ledBBP1"}, -+ {'B',16,"ledBAP2" ,"ledBAP2"}, -+ {'B',17,"ledBBP2" ,"ledBBP2"}, -+ {'B',27,"udpCNX" ,"udpCNX"}, -+ {'B',28,"udpPUP" ,"udpPUP"}, -+ {'B',29,"port2DCD" ,"port2DCD"}, -+ {'C',2, "vlVer100" ,"vlVer150"}, -+ {'C',7, "ledFAP1" ,"ledFAP1"}, -+ {'C',8, "ledFBP1" ,"ledFBP1"}, -+ {'C',10,"vioC10" ,"sdCardON"}, -+ {'C',11,"vioC11" ,"vusbCTRL"}, -+ {'C',12,"sdCardON" ,"simCTRL"}, -+ {'C',13,"vioC13" ,"enbSC3"}, -+ {'C',14,"ledFBP2" ,"ledFBP2"}, -+ {'C',15,"ledFAP2" ,"ledFAP2"}, -+ {0,0,"",""} -+}; -+ -+/* -+{'B',18,"gsmRIO" ,"gsmRIO"}, -+{'B',20,"gsmTX" ,"gsmTX"}, -+{'B',21,"gsmRX" ,"gsmRX"}, -+{'B',22,"gsmPIND" ,"gsmPIND"}, -+{'B',23,"gsmDCD" ,"gsmDCD"}, -+{'B',24,"gsmCTS" ,"gsmCTS"}, -+{'B',25,"gsmDSR" ,"gsmDSR"}, -+{'B',26,"gsmRTS" ,"gsmRTS"}, -+*/ -+static void lookupPINName(char version100, char *devName, char port, char pin); -+// EOF KWJ + AJE -+ -+static ssize_t gpio_read(struct file *file, char __user *buf, size_t len, -+ loff_t *ppos) -+{ -+ unsigned int pin; -+ int retval; -+ char value = '0'; -+ -+ pin = iminor(file->f_dentry->d_inode); -+ -+ retval = at91_get_gpio_value(PIN_BASE + pin); -+ if (retval < 0) -+ return -EFAULT; -+ -+ value = retval + 0x30; -+ if (put_user(value, buf)) -+ return -EFAULT; -+ -+ return 1; -+} -+ -+static ssize_t gpio_write(struct file *file, const char __user *data, -+ size_t len, loff_t *ppos) -+{ -+ unsigned int pin; -+ size_t i; -+ char c; -+ int retval = 0; -+ -+ pin = iminor(file->f_dentry->d_inode); -+ -+ for (i = 0; i < len; i++) { -+ if (get_user(c, data + i)) -+ return -EFAULT; -+ -+ switch (c) { -+ case '0': -+ case '1': -+ retval = at91_set_gpio_value(PIN_BASE + pin, (int)c - 0x30); -+ if (retval < 0) -+ return -EFAULT; -+ break; -+ default: -+ break; -+ } -+ -+ if (retval < 0) -+ break; -+ } -+ -+ return i; -+} -+ -+static int gpio_open(struct inode *inode, struct file *file) -+{ -+ return nonseekable_open(inode, file); -+} -+ -+static int gpio_release(struct inode *inode, struct file *file) -+{ -+ return 0; -+} -+ -+static struct file_operations vio_fops = { -+ .owner = THIS_MODULE, -+ .read = gpio_read, -+ .write = gpio_write, -+ .open = gpio_open, -+ .release = gpio_release, -+}; -+ -+static void vio_setup_cdev(struct vio_dev *dev, int index) -+{ -+ int err, devno = MKDEV(major, index); -+ -+ cdev_init(&dev->cdev, &vio_fops); -+ dev->cdev.owner = THIS_MODULE; -+ dev->cdev.ops = &vio_fops; -+ err = cdev_add (&dev->cdev, devno, 1); -+ if (err) -+ printk(KERN_NOTICE "vio: Error %d adding vio%d", err, index); -+} -+ -+static int vio_remove(struct platform_device *dev) -+{ -+ int i; -+ dev_t devno = MKDEV(major, 0); -+ -+ if (vio_devices) { -+ for(i=0; i<VIO_NR_DEVS; i++) { -+ int iodev = at91_is_pin_gpio(PIN_BASE + i); -+ if (iodev) { -+ cdev_del(&vio_devices[i].cdev); -+ class_device_destroy(vio_class, MKDEV(major, i)); -+ } -+ } -+ kfree(vio_devices); -+ } -+ -+ class_destroy(vio_class); -+ unregister_chrdev_region(devno, VIO_NR_DEVS); -+ -+ platform_set_drvdata(dev, NULL); -+ -+ return 0; -+} -+ -+static int vio_probe(struct platform_device *dev) -+{ -+ int retval, i, j; -+ dev_t vdev = 0; -+ char devName[30]; -+ int vlinkV100; -+ -+ if (major) { -+ vdev = MKDEV(major, 0); -+ retval = register_chrdev_region(vdev, VIO_NR_DEVS, "vio"); -+ } else { -+ retval = alloc_chrdev_region(&vdev, 0, VIO_NR_DEVS, "vio"); -+ major = MAJOR(vdev); -+ } -+ if (retval < 0) { -+ printk(KERN_WARNING "vio: can't get major %d\n", major); -+ return retval; -+ } -+ -+ if (major == 0) { -+ major = retval; -+ printk(KERN_INFO "vio: major number %d\n", major); -+ } -+ -+ vio_class = class_create(THIS_MODULE, "vio"); -+ -+ if (IS_ERR(vio_class)) { -+ printk(KERN_ERR "vio: Error creating vio class\n"); -+ vio_remove(dev); -+ return PTR_ERR(vio_class); -+ } -+ -+ vlinkV100 = at91_get_gpio_value(AT91_PIN_PC2); // Denotes V1.5 if GND -+ -+ vio_devices = kmalloc(VIO_NR_DEVS * sizeof(struct vio_dev), GFP_KERNEL); -+ if (!vio_devices) { -+ retval = -ENOMEM; -+ goto fail; -+ } -+ memset(vio_devices, 0, VIO_NR_DEVS * sizeof(struct vio_dev)); -+ -+ for (i=0; i<VIO_NR_DEVS/32; i++) -+ for(j=0; j<32; j++) { -+ int iodev = at91_is_pin_gpio(PIN_BASE + i*32 + j); -+ if (iodev) { -+ vio_setup_cdev(&vio_devices[i*32 + j], i*32 + j); -+ // Lookup name of vio to create -+ lookupPINName(vlinkV100, devName, i, j); -+ class_device_create(vio_class, NULL, MKDEV(major, i*32 + j), NULL, devName); -+ } -+ } -+ -+ platform_set_drvdata(dev, vio_devices); -+ -+ return 0; -+ -+fail: -+ vio_remove(dev); -+ return retval; -+} -+ -+static void lookupPINName(char version100, char *devName, char port, char pin) -+{ -+ int i = -1; -+ char found = 0; -+ while (!found) -+ { -+ i++; -+ if (i >= MAX_VIO_NAMES) -+ break; -+ if (VioName[i].port == port+'A' && VioName[i].pin == pin) -+ { -+ printk(KERN_ERR "vio++: %c%d=%s\n",VioName[i].port,VioName[i].pin,VioName[i].name150); -+ if (version100) -+ strcpy(devName, VioName[i].name100); -+ else -+ strcpy(devName, VioName[i].name150); -+ found = 1; -+ } -+ } -+ if (!found) -+ sprintf(devName, "vio%c%d", port + 'A', pin); -+} -+ -+static struct platform_device *vio_platform_device; -+ -+static struct platform_driver vio_driver = { -+ .probe = vio_probe, -+ .remove = vio_remove, -+ .driver = { -+ .name = "vio", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+static int __init vio_init(void) -+{ -+ int retval; -+ -+ vio_platform_device = platform_device_register_simple("vio", -1, NULL, 0); -+ if (IS_ERR(vio_platform_device)) { -+ printk(KERN_WARNING "vio: device registration failed\n"); -+ return PTR_ERR(vio_platform_device); -+ } -+ -+ retval = platform_driver_register(&vio_driver); -+ if (retval < 0) { -+ printk(KERN_WARNING "vio: driver registration failed\n"); -+ platform_device_unregister(vio_platform_device); -+ } -+ -+ return retval; -+} -+ -+static void __exit vio_exit(void) -+{ -+ platform_driver_unregister(&vio_driver); -+ platform_device_unregister(vio_platform_device); -+} -+ -+module_init(vio_init); -+module_exit(vio_exit); -+ -+MODULE_AUTHOR("Hamish Guthrie <hamish@prodigi.ch>"); -+MODULE_DESCRIPTION("FDL Versalink GPIO Driver"); ---- a/include/asm-arm/arch-at91/gpio.h -+++ b/include/asm-arm/arch-at91/gpio.h -@@ -199,6 +199,7 @@ extern int __init_or_module at91_set_mul - /* callable at any time */ - extern int at91_set_gpio_value(unsigned pin, int value); - extern int at91_get_gpio_value(unsigned pin); -+extern int at91_is_pin_gpio(unsigned pin); - - /* callable only from core power-management code */ - extern void at91_gpio_suspend(void); diff --git a/target/linux/at91/patches-2.6.25/007-mtd-partition.patch b/target/linux/at91/patches-2.6.25/007-mtd-partition.patch deleted file mode 100644 index 503c89200b..0000000000 --- a/target/linux/at91/patches-2.6.25/007-mtd-partition.patch +++ /dev/null @@ -1,36 +0,0 @@ ---- a/drivers/mtd/devices/at91_dataflash.c -+++ b/drivers/mtd/devices/at91_dataflash.c -@@ -175,7 +175,7 @@ static struct mtd_partition static_parti - }; - #endif - --static const char *part_probes[] = { "cmdlinepart", NULL, }; -+static const char *part_probes[] = { "cmdlinepart", "at91part", NULL, }; - - #endif - ---- a/drivers/mtd/Kconfig -+++ b/drivers/mtd/Kconfig -@@ -168,6 +168,12 @@ config MTD_OF_PARTS - the partition map from the children of the flash node, - as described in Documentation/powerpc/booting-without-of.txt. - -+config MTD_AT91_PARTS -+ tristate "Atmel AT91 partitioning support" -+ depends on MTD_PARTITIONS && ARCH_AT91RM9200 && AT91_SPI -+ ---help--- -+ Atmel AT91 partitioning support -+ - comment "User Modules And Translation Layers" - - config MTD_CHAR ---- a/drivers/mtd/Makefile -+++ b/drivers/mtd/Makefile -@@ -12,6 +12,7 @@ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redbo - obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o - obj-$(CONFIG_MTD_AFS_PARTS) += afs.o - obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o -+obj-$(CONFIG_MTD_AT91_PARTS) += at91part.o - - # 'Users' - code which presents functionality to userspace. - obj-$(CONFIG_MTD_CHAR) += mtdchar.o diff --git a/target/linux/at91/patches-2.6.25/008-fdl-serial.patch b/target/linux/at91/patches-2.6.25/008-fdl-serial.patch deleted file mode 100644 index cf11ac0da5..0000000000 --- a/target/linux/at91/patches-2.6.25/008-fdl-serial.patch +++ /dev/null @@ -1,161 +0,0 @@ ---- a/drivers/serial/atmel_serial.c -+++ b/drivers/serial/atmel_serial.c -@@ -214,6 +214,34 @@ static void atmel_set_mctrl(struct uart_ - at91_set_gpio_value(AT91_PIN_PA21, 0); - else - at91_set_gpio_value(AT91_PIN_PA21, 1); -+ -+ /* -+ * FDL VersaLink adds GPIOS to provide full modem -+ * control on USART 0 - Drive DTR and RI pins manually -+ */ -+ if (mctrl & TIOCM_DTR) -+ at91_set_gpio_value(AT91_PIN_PB6, 0); -+ else -+ at91_set_gpio_value(AT91_PIN_PB6, 1); -+ if (mctrl & TIOCM_RI) -+ at91_set_gpio_value(AT91_PIN_PB7, 0); -+ else -+ at91_set_gpio_value(AT91_PIN_PB7, 1); -+ } -+ -+ /* -+ * FDL VersaLink adds GPIOS to provide full modem control on -+ * USART 3 - Drive DTR and RI pins manually -+ */ -+ if (port->mapbase == AT91RM9200_BASE_US3) { -+ if (mctrl & TIOCM_DTR) -+ at91_set_gpio_value(AT91_PIN_PB29, 0); -+ else -+ at91_set_gpio_value(AT91_PIN_PB29, 1); -+ if (mctrl & TIOCM_RI) -+ at91_set_gpio_value(AT91_PIN_PB2, 0); -+ else -+ at91_set_gpio_value(AT91_PIN_PB2, 1); - } - } - #endif -@@ -251,8 +279,10 @@ static u_int atmel_get_mctrl(struct uart - /* - * The control signals are active low. - */ -- if (!(status & ATMEL_US_DCD)) -- ret |= TIOCM_CD; -+ -+ if (!(port->mapbase == AT91RM9200_BASE_US0 || port->mapbase == AT91RM9200_BASE_US3)) -+ if (!(status & ATMEL_US_DCD)) -+ ret |= TIOCM_CD; - if (!(status & ATMEL_US_CTS)) - ret |= TIOCM_CTS; - if (!(status & ATMEL_US_DSR)) -@@ -260,6 +290,16 @@ static u_int atmel_get_mctrl(struct uart - if (!(status & ATMEL_US_RI)) - ret |= TIOCM_RI; - -+ /* -+ * Read the GPIO's for the FDL VersaLink special case -+ */ -+ if (port->mapbase == AT91RM9200_BASE_US0) -+ if (!(at91_get_gpio_value(AT91_PIN_PA19))) -+ ret |= TIOCM_CD; -+ if (port->mapbase == AT91RM9200_BASE_US3) -+ if (!(at91_get_gpio_value(AT91_PIN_PA24))) -+ ret |= TIOCM_CD; -+ - return ret; - } - -@@ -453,6 +493,34 @@ static void atmel_tx_chars(struct uart_p - } - - /* -+ * USART0 DCD Interrupt handler -+ */ -+ -+static irqreturn_t atmel_u0_DCD_interrupt(int irq, void *dev_id) -+{ -+ struct uart_port *port = dev_id; -+ int status = at91_get_gpio_value(irq); -+ -+ uart_handle_dcd_change(port, !(status)); -+ -+ return IRQ_HANDLED; -+} -+ -+/* -+ * USART3 DCD Interrupt handler -+ */ -+ -+static irqreturn_t atmel_u3_DCD_interrupt(int irq, void *dev_id) -+{ -+ struct uart_port *port = dev_id; -+ int status = at91_get_gpio_value(irq); -+ -+ uart_handle_dcd_change(port, !(status)); -+ -+ return IRQ_HANDLED; -+} -+ -+/* - * receive interrupt handler. - */ - static void -@@ -815,6 +883,23 @@ static int atmel_startup(struct uart_por - return retval; - } - -+ if (port->mapbase == AT91RM9200_BASE_US0) { -+ retval = request_irq(AT91_PIN_PA19, atmel_u0_DCD_interrupt, 0, "atmel_serial", port); -+ if (retval) { -+ printk("atmel_serial: atmel_startup - Can't get u0DCD irq\n"); -+ free_irq(port->irq, port); -+ return retval; -+ } -+ } -+ if (port->mapbase == AT91RM9200_BASE_US3) { -+ retval = request_irq(AT91_PIN_PA24, atmel_u3_DCD_interrupt, 0, "atmel_serial", port); -+ if (retval) { -+ printk("atmel_serial: atmel_startup - Can't get u3DCD irq\n"); -+ free_irq(port->irq, port); -+ return retval; -+ } -+ } -+ - /* - * Initialize DMA (if necessary) - */ -@@ -834,6 +919,10 @@ static int atmel_startup(struct uart_por - kfree(atmel_port->pdc_rx[0].buf); - } - free_irq(port->irq, port); -+ if (port->mapbase == AT91RM9200_BASE_US0) -+ free_irq(AT91_PIN_PA19, port); -+ if (port->mapbase == AT91RM9200_BASE_US3) -+ free_irq(AT91_PIN_PA24, port); - return -ENOMEM; - } - pdc->dma_addr = dma_map_single(port->dev, -@@ -873,7 +962,11 @@ static int atmel_startup(struct uart_por - retval = atmel_open_hook(port); - if (retval) { - free_irq(port->irq, port); -- return retval; -+ if (port->mapbase == AT91RM9200_BASE_US0) -+ free_irq(AT91_PIN_PA19, port); -+ if (port->mapbase == AT91RM9200_BASE_US3) -+ free_irq(AT91_PIN_PA24, port); -+ return retval; - } - } - -@@ -947,6 +1040,10 @@ static void atmel_shutdown(struct uart_p - * Free the interrupt - */ - free_irq(port->irq, port); -+ if (port->mapbase == AT91RM9200_BASE_US0) -+ free_irq(AT91_PIN_PA19, port); -+ if (port->mapbase == AT91RM9200_BASE_US3) -+ free_irq(AT91_PIN_PA24, port); - - /* - * If there is a specific "close" function (to unregister diff --git a/target/linux/at91/patches-2.6.25/009-fdl-uartinit.patch b/target/linux/at91/patches-2.6.25/009-fdl-uartinit.patch deleted file mode 100644 index d30023186a..0000000000 --- a/target/linux/at91/patches-2.6.25/009-fdl-uartinit.patch +++ /dev/null @@ -1,34 +0,0 @@ ---- a/arch/arm/mach-at91/at91rm9200_devices.c -+++ b/arch/arm/mach-at91/at91rm9200_devices.c -@@ -1001,7 +1001,15 @@ static inline void configure_usart0_pins - * We need to drive the pin manually. Default is off (RTS is active low). - */ - at91_set_gpio_output(AT91_PIN_PA21, 1); -- } -+ } -+ if (pins & ATMEL_UART_DTR) -+ at91_set_gpio_output(AT91_PIN_PB6, 1); /* DTR0 */ -+ if (pins & ATMEL_UART_RI) -+ at91_set_gpio_output(AT91_PIN_PB7, 1); /* RI0 */ -+ if (pins & ATMEL_UART_DCD) { -+ at91_set_gpio_input(AT91_PIN_PA19, 1); /* DCD0 */ -+ at91_set_deglitch(AT91_PIN_PA19, 1); -+ } - } - - static struct resource uart1_resources[] = { -@@ -1139,6 +1147,14 @@ static inline void configure_usart3_pins - at91_set_B_periph(AT91_PIN_PB1, 0); /* CTS3 */ - if (pins & ATMEL_UART_RTS) - at91_set_B_periph(AT91_PIN_PB0, 0); /* RTS3 */ -+ if (pins & ATMEL_UART_DTR) -+ at91_set_gpio_output(AT91_PIN_PB29, 1); /* DTR0 */ -+ if (pins & ATMEL_UART_RI) -+ at91_set_gpio_output(AT91_PIN_PB2, 1); /* RI0 */ -+ if (pins & ATMEL_UART_DCD) { -+ at91_set_gpio_input(AT91_PIN_PA24, 1); /* DCD0 */ -+ at91_set_deglitch(AT91_PIN_PA24, 1); -+ } - } - - static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */ diff --git a/target/linux/at91/patches-2.6.25/010-dm9161a-phyfix.patch b/target/linux/at91/patches-2.6.25/010-dm9161a-phyfix.patch deleted file mode 100644 index 756e014f02..0000000000 --- a/target/linux/at91/patches-2.6.25/010-dm9161a-phyfix.patch +++ /dev/null @@ -1,28 +0,0 @@ ---- a/drivers/net/arm/at91_ether.c -+++ b/drivers/net/arm/at91_ether.c -@@ -146,6 +146,7 @@ static void update_linkspeed(struct net_ - struct at91_private *lp = netdev_priv(dev); - unsigned int bmsr, bmcr, lpa, mac_cfg; - unsigned int speed, duplex; -+ unsigned long timeout = jiffies + HZ; - - if (!mii_link_ok(&lp->mii)) { /* no link */ - netif_carrier_off(dev); -@@ -158,8 +159,15 @@ static void update_linkspeed(struct net_ - read_phy(lp->phy_address, MII_BMSR, &bmsr); - read_phy(lp->phy_address, MII_BMCR, &bmcr); - if (bmcr & BMCR_ANENABLE) { /* AutoNegotiation is enabled */ -- if (!(bmsr & BMSR_ANEGCOMPLETE)) -- return; /* Do nothing - another interrupt generated when negotiation complete */ -+ while (!(bmsr & BMSR_ANEGCOMPLETE)) { -+ if (time_after(jiffies, timeout)) { -+ printk("at91_ether: Auto-negotiate timeout\n"); -+ return; -+ } -+ read_phy(lp->phy_address, MII_BMSR, &bmsr); -+ read_phy(lp->phy_address, MII_BMCR, &bmcr); -+ cpu_relax(); -+ } - - read_phy(lp->phy_address, MII_LPA, &lpa); - if ((lpa & LPA_100FULL) || (lpa & LPA_100HALF)) speed = SPEED_100; diff --git a/target/linux/at91/patches-2.6.25/014-initpartition.patch b/target/linux/at91/patches-2.6.25/014-initpartition.patch deleted file mode 100644 index 554c1491e7..0000000000 --- a/target/linux/at91/patches-2.6.25/014-initpartition.patch +++ /dev/null @@ -1,18 +0,0 @@ ---- a/drivers/mtd/devices/at91_dataflash.c -+++ b/drivers/mtd/devices/at91_dataflash.c -@@ -163,12 +163,12 @@ static struct mtd_partition static_parti - .mask_flags = MTD_WRITEABLE, /* read-only */ - }, - { -- .name = "kernel", -+ .name = "knlroot", - .offset = MTDPART_OFS_NXTBLK, -- .size = 5 * 32 * 8 * 1056, /* 5 sectors */ -+ .size = 0x320400, - }, - { -- .name = "filesystem", -+ .name = "jffs2", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL, /* rest = 26 sectors */ - } diff --git a/target/linux/at91/patches-2.6.25/017-usb_serial_endpoint_size.patch b/target/linux/at91/patches-2.6.25/017-usb_serial_endpoint_size.patch deleted file mode 100644 index 7bd38b4434..0000000000 --- a/target/linux/at91/patches-2.6.25/017-usb_serial_endpoint_size.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/drivers/usb/serial/usb-serial.c -+++ b/drivers/usb/serial/usb-serial.c -@@ -904,7 +904,7 @@ int usb_serial_probe(struct usb_interfac - dev_err(&interface->dev, "No free urbs available\n"); - goto probe_error; - } -- buffer_size = (endpoint->wMaxPacketSize > maxSize) ? endpoint->wMaxPacketSize : maxSize; -+ buffer_size = 2048; - port->bulk_in_size = buffer_size; - port->bulk_in_endpointAddress = endpoint->bEndpointAddress; - port->bulk_in_buffer = kmalloc (buffer_size, GFP_KERNEL); |