diff options
Diffstat (limited to 'target')
9 files changed, 347 insertions, 217 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 24b59d6630..74f39ef6de 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -64,7 +64,9 @@ ipq40xx_setup_interfaces() mobipromo,cm520-79f) ucidef_set_interfaces_lan_wan "lan1 lan2" "wan" ;; - mikrotik,wap-ac) + mikrotik,wap-ac|\ + mikrotik,wap-ac-lte|\ + mikrotik,wap-r-ac) ucidef_set_interface_lan "sw-eth1 sw-eth2" ;; netgear,rbr50|\ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 7498e1c710..7f41bdcfcc 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -113,7 +113,9 @@ case "$FIRMWARE" in mikrotik,hap-ac2 |\ mikrotik,hap-ac3 |\ mikrotik,hap-ac3-lte6-kit |\ - mikrotik,wap-ac) + mikrotik,wap-ac |\ + mikrotik,wap-ac-lte |\ + mikrotik,wap-r-ac) wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data" ( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x0 0x2f20 ) || \ ( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x0 0x2f20 ) @@ -207,7 +209,9 @@ case "$FIRMWARE" in mikrotik,hap-ac3 |\ mikrotik,hap-ac3-lte6-kit |\ mikrotik,sxtsq-5-ac |\ - mikrotik,wap-ac) + mikrotik,wap-ac |\ + mikrotik,wap-ac-lte |\ + mikrotik,wap-r-ac) wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data" ( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x8000 0x2f20 ) || \ ( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x0 0x2f20 ) @@ -243,7 +247,9 @@ case "$FIRMWARE" in mikrotik,hap-ac2 |\ mikrotik,hap-ac3 |\ mikrotik,hap-ac3-lte6-kit |\ - mikrotik,wap-ac) + mikrotik,wap-ac |\ + mikrotik,wap-ac-lte |\ + mikrotik,wap-r-ac) wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data" ( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x2f20 0x2f20 ) || \ ( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x2f20 0x2f20 ) @@ -257,7 +263,9 @@ case "$FIRMWARE" in mikrotik,hap-ac3 |\ mikrotik,hap-ac3-lte6-kit |\ mikrotik,sxtsq-5-ac |\ - mikrotik,wap-ac) + mikrotik,wap-ac |\ + mikrotik,wap-ac-lte |\ + mikrotik,wap-r-ac) wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data" ( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0xaf20 0x2f20 ) || \ ( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x2f20 0x2f20 ) diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh index ddfef1ab2d..ce0b55bb80 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh @@ -29,7 +29,9 @@ preinit_set_mac_address() { ip link set dev lan1 address $(macaddr_add "$base_mac" 1) ip link set dev eth0 address $(macaddr_setbit "$base_mac" 7) ;; - mikrotik,wap-ac) + mikrotik,wap-ac|\ + mikrotik,wap-ac-lte|\ + mikrotik,wap-r-ac) base_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base) ip link set dev sw-eth1 address "$base_mac" ip link set dev sw-eth2 address $(macaddr_add "$base_mac" 1) diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 6b8f62d735..12fa9699c5 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -177,7 +177,9 @@ platform_do_upgrade() { mikrotik,hap-ac3-lte6-kit|\ mikrotik,lhgg-60ad|\ mikrotik,sxtsq-5-ac|\ - mikrotik,wap-ac) + mikrotik,wap-ac|\ + mikrotik,wap-ac-lte|\ + mikrotik,wap-r-ac) [ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware default_do_upgrade "$1" ;; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac-lte.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac-lte.dts new file mode 100644 index 0000000000..8ff18d92b7 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac-lte.dts @@ -0,0 +1,45 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2022, Alexander Couzens <lynxis@fe80.eu> */ + +#include "qcom-ipq4018-wap-ac.dtsi" + +/ { + model = "MikroTik wAP ac LTE"; + compatible = "mikrotik,wap-ac-lte"; + + soc { + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + phys = <&usb3_hs_phy>; + phy-names = "usb2-phy"; + }; + }; + }; +}; + +&tlmm { + enable-usb-power { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "enable USB power"; + }; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts index ecbdfac15f..1bfcbf1e33 100644 --- a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dts @@ -1,218 +1,9 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT /* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */ -#include "qcom-ipq4019.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include <dt-bindings/soc/qcom,tcsr.h> +#include "qcom-ipq4018-wap-ac.dtsi" / { model = "MikroTik wAP ac"; compatible = "mikrotik,wap-ac"; - - memory { - device_type = "memory"; - reg = <0x80000000 0x08000000>; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - aliases { - led-boot = &led_user; - led-failsafe = &led_user; - led-running = &led_user; - led-upgrade = &led_user; - }; - - soc { - counter@4a1000 { - compatible = "qcom,qca-gcnt"; - reg = <0x4a1000 0x4>; - }; - - tcsr@1949000 { - compatible = "qcom,tcsr"; - reg = <0x1949000 0x100>; - qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; - }; - - ess_tcsr@1953000 { - compatible = "qcom,tcsr"; - reg = <0x1953000 0x1000>; - qcom,ess-interface-select = <TCSR_ESS_PSGMII>; - }; - - tcsr@1957000 { - compatible = "qcom,tcsr"; - reg = <0x1957000 0x100>; - qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; - }; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - }; - - leds { - compatible = "gpio-leds"; - - power { - label = "blue:power"; - gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - led_user: user { - label = "green:user"; - gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; - panic-indicator; - }; - }; -}; - -&prng { - status = "okay"; -}; - -&tlmm { - serial_pins: serial_pinmux { - mux { - pins = "gpio60", "gpio61"; - function = "blsp_uart0"; - bias-disable; - }; - }; - - spi_0_pins: spi_0_pinmux { - pin { - function = "blsp_spi0"; - pins = "gpio55", "gpio56", "gpio57"; - drive-strength = <2>; - bias-disable; - }; - pin_cs { - function = "gpio"; - pins = "gpio54"; - drive-strength = <2>; - bias-disable; - output-high; - }; - }; -}; - -&blsp_dma { - status = "okay"; -}; - -&blsp1_spi1 { - status = "okay"; - - pinctrl-0 = <&spi_0_pins>; - pinctrl-names = "default"; - cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; - - flash@0 { - reg = <0>; - compatible = "jedec,spi-nor"; - spi-max-frequency = <40000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "Qualcomm"; - reg = <0x0 0x80000>; - read-only; - }; - - partition@80000 { - compatible = "mikrotik,routerboot-partitions"; - #address-cells = <1>; - #size-cells = <1>; - label = "RouterBoot"; - reg = <0x80000 0x80000>; - - hard_config { - read-only; - size = <0x2000>; - }; - - dtb_config { - read-only; - }; - - soft_config { - }; - }; - - partition@100000 { - compatible = "mikrotik,minor"; - label = "firmware"; - reg = <0x100000 0xf00000>; - }; - }; - }; -}; - -&blsp1_uart1 { - status = "okay"; - - pinctrl-0 = <&serial_pins>; - pinctrl-names = "default"; -}; - -&cryptobam { - status = "okay"; -}; - -&crypto { - status = "okay"; -}; - -&watchdog { - status = "okay"; -}; - -&mdio { - status = "okay"; -}; - -&gmac { - status = "okay"; -}; - -&switch { - status = "okay"; -}; - -&swport4 { - status = "okay"; - label = "sw-eth2"; -}; - -&swport5 { - status = "okay"; - label = "sw-eth1"; -}; - -&wifi0 { - status = "okay"; - - qcom,ath10k-calibration-variant = "MikroTik-wAP-ac"; -}; - -&wifi1 { - status = "okay"; - - qcom,ath10k-calibration-variant = "MikroTik-wAP-ac"; }; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dtsi b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dtsi new file mode 100644 index 0000000000..777f46e3af --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-ac.dtsi @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */ + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + memory { + device_type = "memory"; + reg = <0x80000000 0x08000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + led-boot = &led_user; + led-failsafe = &led_user; + led-running = &led_user; + led-upgrade = &led_user; + }; + + soc { + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + leds { + compatible = "gpio-leds"; + + power { + label = "blue:power"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + led_user: user { + label = "green:user"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + }; +}; + +&prng { + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <2>; + bias-disable; + }; + pin_cs { + function = "gpio"; + pins = "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Qualcomm"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + compatible = "mikrotik,routerboot-partitions"; + #address-cells = <1>; + #size-cells = <1>; + label = "RouterBoot"; + reg = <0x80000 0x80000>; + + hard_config { + read-only; + size = <0x2000>; + }; + + dtb_config { + read-only; + }; + + soft_config { + }; + }; + + partition@100000 { + compatible = "mikrotik,minor"; + label = "firmware"; + reg = <0x100000 0xf00000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&mdio { + status = "okay"; +}; + +&gmac { + status = "okay"; +}; + +&switch { + status = "okay"; +}; + +&swport4 { + status = "okay"; + label = "sw-eth2"; +}; + +&swport5 { + status = "okay"; + label = "sw-eth1"; +}; + +&wifi0 { + status = "okay"; + + qcom,ath10k-calibration-variant = "MikroTik-wAP-ac"; +}; + +&wifi1 { + status = "okay"; + + qcom,ath10k-calibration-variant = "MikroTik-wAP-ac"; +}; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-r-ac.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-r-ac.dts new file mode 100644 index 0000000000..e7f28f23cf --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-wap-r-ac.dts @@ -0,0 +1,45 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2022, Alexander Couzens <lynxis@fe80.eu> */ + +#include "qcom-ipq4018-wap-ac.dtsi" + +/ { + model = "MikroTik wAP R ac"; + compatible = "mikrotik,wap-r-ac"; + + soc { + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + phys = <&usb3_hs_phy>; + phy-names = "usb2-phy"; + }; + }; + }; +}; + +&tlmm { + enable-usb-power { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "enable USB power"; + }; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/mikrotik.mk b/target/linux/ipq40xx/image/mikrotik.mk index 3eacedd9d8..f0e1f1aad3 100644 --- a/target/linux/ipq40xx/image/mikrotik.mk +++ b/target/linux/ipq40xx/image/mikrotik.mk @@ -78,3 +78,23 @@ define Device/mikrotik_wap-ac DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers endef TARGET_DEVICES += mikrotik_wap-ac + +define Device/mikrotik_wap-r-ac + $(call Device/mikrotik_wap-ac) + DEVICE_MODEL := wAP R ac + DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi \ + kmod-usb-acm kmod-usb-net-rndis + DEVICE_DTS := qcom-ipq4018-wap-r-ac +endef +TARGET_DEVICES += mikrotik_wap-r-ac + +define Device/mikrotik_wap-ac-lte + $(call Device/mikrotik_wap-ac) + DEVICE_MODEL := wAP ac LTE + DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi \ + kmod-usb-acm kmod-usb-net-rndis + DEVICE_DTS := qcom-ipq4018-wap-ac-lte + DEVICE_ALT0_VENDOR = Mikrotik + DEVICE_ALT0_MODEL := wAP ac LTE6 +endef +TARGET_DEVICES += mikrotik_wap-ac-lte |