diff options
Diffstat (limited to 'target')
9 files changed, 841 insertions, 2 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 13e2722f79..0e4b947c5f 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -63,6 +63,11 @@ ipq40xx_setup_interfaces() engenius,eap2200) ucidef_set_interface_lan "eth0 eth1" ;; + cellc,rtl30vw) + ucidef_set_interface_lan "eth0" + ucidef_add_switch "switch0" \ + "0u@eth0" "3:lan" "4:lan" + ;; ezviz,cs-w3-wd1200g-eup) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches index e46a297ea7..c255707f91 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches @@ -7,6 +7,12 @@ board_config_update board=$(board_name) case "$board" in +cellc,rtl30vw) + ucidef_add_gpio_switch "w_disable" "W_DISABLE mPCIE pin" "398" "1" + ucidef_add_gpio_switch "pmd_resin_n" "PMD_RESIN_N pin" "399" "1" + ucidef_add_gpio_switch "mcpie_vcc" "LTE power" "400" "0" + ucidef_add_gpio_switch "usb_vcc" "USB power" "401" "0" + ;; cilab,meshpoint-one) ucidef_add_gpio_switch "poe_passtrough" "POE passtrough enable" "413" "1" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index dd301b1e30..814d5b0371 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -80,6 +80,7 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + cellc,rtl30vw |\ compex,wpj419 |\ compex,wpj428 |\ engenius,eap1300 |\ @@ -162,6 +163,7 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + cellc,rtl30vw |\ compex,wpj419 |\ compex,wpj428 |\ engenius,eap1300 |\ diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 7aabeeeea0..d3effdf7e2 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -29,6 +29,17 @@ EOF return 0; } +askey_do_upgrade() { + local tar_file="$1" + + local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$') + board_dir=${board_dir%/} + + tar Oxf $tar_file ${board_dir}/root | mtd write - rootfs + + nand_do_upgrade "$1" +} + zyxel_do_upgrade() { local tar_file="$1" @@ -78,6 +89,10 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; + cellc,rtl30vw) + CI_UBIPART="ubifs" + askey_do_upgrade "$1" + ;; compex,wpj419) nand_do_upgrade "$1" ;; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-rtl30vw.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-rtl30vw.dts new file mode 100644 index 0000000000..2f17424e55 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-rtl30vw.dts @@ -0,0 +1,385 @@ +// SPDX-License-Identifier: ISC +// Copyright (c) 2015, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Cezary Jackiewicz <cezary@eko.one.pl>. +// Copyright (c) 2020, Pawel Dembicki <paweldembicki@gmail.com>. + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/soc/qcom,tcsr.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Cell C RTL30VW"; + compatible = "cellc,rtl30vw"; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_red; + led-running = &led_power_blue; + led-upgrade = &led_power_red; + }; + + chosen { + bootargs-append = "ubi.mtd=ubifs root=/dev/ubiblock0_0 rootfstype=squashfs ro"; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + num-chipselects = <1>; + + mosi-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; + cs-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>; + sck-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; + + led_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <2>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_blue: power_blue { + gpios = <&led_gpio 0 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:power"; + default-state = "on"; + }; + + led_power_red: power_red { + gpios = <&led_gpio 1 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:red:power"; + }; + + tp28 { + gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>; + label = "rtl30vw:ext:tp28"; + default-state = "keep"; + }; + + tp27 { + gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>; + label = "rtl30vw:ext:tp27"; + default-state = "keep"; + }; + + wlan2g { + gpios = <&led_gpio 8 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:wlan2g"; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + gpios = <&led_gpio 9 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:wlan5g"; + linux,default-trigger = "phy1tpt"; + }; + + wps { + gpios = <&led_gpio 10 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:wps"; + }; + + voip { + gpios = <&led_gpio 11 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:voip"; + }; + + s1 { + gpios = <&led_gpio 12 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s1"; + }; + + s2 { + gpios = <&led_gpio 13 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s2"; + }; + + s3 { + gpios = <&led_gpio 14 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s3"; + }; + + s4 { + gpios = <&led_gpio 15 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s4"; + }; + + signal { + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:red:signal"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + }; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>; + + flash@0 { + /*"n25q128a11" is required for proper nand recognition in u-boot. */ + compatible = "jedec,spi-nor", "n25q128a11"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + }; + + partition@180000 { + label = "0:BOOTCONFIG"; + reg = <0x180000 0x10000>; + read-only; + }; + }; + }; + + flash@1 { + /* + * Factory U-boot looks in 0:BOOTCONFIG partition for active + * partitions settings and mangle partition config. So kernel + * /kernel_1 and rootfs/rootfs_1 pairs can be swaped. + * It isn't a problem but we never can be sure where OFW put + * factory images. "spinand,mt29f" value is required for proper + * nand recognition in u-boot. + */ + compatible = "spi-nand","spinand,mt29f"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "rootfs"; + reg = <0x400000 0x2000000>; + }; + + partition@2400000 { + label = "kernel_1"; + reg = <0x2400000 0x400000>; + }; + + partition@2800000 { + label = "rootfs_1"; + reg = <0x2800000 0x2000000>; + }; + + partition@4800000 { + label = "ubifs"; + reg = <0x4800000 0x3800000>; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "cellc,rtl30vw"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "cellc,rtl30vw"; +}; diff --git a/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-rtl30vw.dts b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-rtl30vw.dts new file mode 100644 index 0000000000..2f17424e55 --- /dev/null +++ b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-rtl30vw.dts @@ -0,0 +1,385 @@ +// SPDX-License-Identifier: ISC +// Copyright (c) 2015, The Linux Foundation. All rights reserved. +// Copyright (c) 2019, Cezary Jackiewicz <cezary@eko.one.pl>. +// Copyright (c) 2020, Pawel Dembicki <paweldembicki@gmail.com>. + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/soc/qcom,tcsr.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Cell C RTL30VW"; + compatible = "cellc,rtl30vw"; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_red; + led-running = &led_power_blue; + led-upgrade = &led_power_red; + }; + + chosen { + bootargs-append = "ubi.mtd=ubifs root=/dev/ubiblock0_0 rootfstype=squashfs ro"; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + num-chipselects = <1>; + + mosi-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; + cs-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>; + sck-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; + + led_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <2>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_blue: power_blue { + gpios = <&led_gpio 0 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:power"; + default-state = "on"; + }; + + led_power_red: power_red { + gpios = <&led_gpio 1 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:red:power"; + }; + + tp28 { + gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>; + label = "rtl30vw:ext:tp28"; + default-state = "keep"; + }; + + tp27 { + gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>; + label = "rtl30vw:ext:tp27"; + default-state = "keep"; + }; + + wlan2g { + gpios = <&led_gpio 8 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:wlan2g"; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + gpios = <&led_gpio 9 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:wlan5g"; + linux,default-trigger = "phy1tpt"; + }; + + wps { + gpios = <&led_gpio 10 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:wps"; + }; + + voip { + gpios = <&led_gpio 11 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:voip"; + }; + + s1 { + gpios = <&led_gpio 12 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s1"; + }; + + s2 { + gpios = <&led_gpio 13 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s2"; + }; + + s3 { + gpios = <&led_gpio 14 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s3"; + }; + + s4 { + gpios = <&led_gpio 15 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:blue:s4"; + }; + + signal { + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + label = "rtl30vw:red:signal"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + }; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>; + + flash@0 { + /*"n25q128a11" is required for proper nand recognition in u-boot. */ + compatible = "jedec,spi-nor", "n25q128a11"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + }; + + partition@180000 { + label = "0:BOOTCONFIG"; + reg = <0x180000 0x10000>; + read-only; + }; + }; + }; + + flash@1 { + /* + * Factory U-boot looks in 0:BOOTCONFIG partition for active + * partitions settings and mangle partition config. So kernel + * /kernel_1 and rootfs/rootfs_1 pairs can be swaped. + * It isn't a problem but we never can be sure where OFW put + * factory images. "spinand,mt29f" value is required for proper + * nand recognition in u-boot. + */ + compatible = "spi-nand","spinand,mt29f"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "rootfs"; + reg = <0x400000 0x2000000>; + }; + + partition@2400000 { + label = "kernel_1"; + reg = <0x2400000 0x400000>; + }; + + partition@2800000 { + label = "rootfs_1"; + reg = <0x2800000 0x2000000>; + }; + + partition@4800000 { + label = "ubifs"; + reg = <0x4800000 0x3800000>; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "cellc,rtl30vw"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "cellc,rtl30vw"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index c47eec51a0..bf69953eac 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -53,6 +53,14 @@ define Device/DniImage IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata endef +define Build/append-rootfshdr + mkimage -A $(LINUX_KARCH) \ + -O linux -T filesystem \ + -C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \ + -n root.squashfs -d $(IMAGE_ROOTFS) $@.new + dd if=$@.new bs=64 count=1 >> $(IMAGE_KERNEL) +endef + define Build/mkmylofw_32m $(eval device_id=$(word 1,$(1))) $(eval revision=$(word 2,$(1))) @@ -69,6 +77,15 @@ define Build/mkmylofw_32m @mv $@.new $@ endef +define Build/qsdk-ipq-factory-nand-askey + $(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\ + askey_kernel $(IMAGE_KERNEL) \ + askey_fs $(IMAGE_ROOTFS) \ + ubifs $@ + PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new + @mv $@.new $@ +endef + define Build/SenaoFW -$(STAGING_DIR_HOST)/bin/mksenaofw \ -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \ @@ -228,6 +245,28 @@ define Device/avm_fritzrepeater-3000 endef TARGET_DEVICES += avm_fritzrepeater-3000 +define Device/cellc_rtl30vw + KERNEL_SUFFIX := -fit-uImage.itb + KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb + KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048 + KERNEL_NAME := Image + KERNEL_IN_UBI := + IMAGES := nand-factory.bin nand-sysupgrade.bin + IMAGE/nand-factory.bin := append-rootfshdr | append-ubi | qsdk-ipq-factory-nand-askey + IMAGE/nand-sysupgrade.bin := append-rootfshdr | sysupgrade-tar | append-metadata + DEVICE_VENDOR := Cell C + DEVICE_MODEL := RTL30VW + SOC := qcom-ipq4019 + DEVICE_DTS_CONFIG := config@5 + KERNEL_INSTALL := 1 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 57344k + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi ipq-wifi-cellc_rtl30vw +endef +TARGET_DEVICES += cellc_rtl30vw + define Device/cilab_meshpoint-one $(call Device/8dev_jalapeno-common) DEVICE_VENDOR := Crisis Innovation Lab diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 24965cf264..2af342c4be 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,45 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,46 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -46,6 +46,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-e2600ac-c1.dtb \ + qcom-ipq4019-e2600ac-c2.dtb \ ++ qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-u4019-32m.dtb \ + qcom-ipq4019-wpj419.dtb \ + qcom-ipq4028-wpj428.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index a17314240f..46af5fb5c9 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,45 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,46 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -46,6 +46,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-e2600ac-c1.dtb \ + qcom-ipq4019-e2600ac-c2.dtb \ + qcom-ipq4019-habanero-dvk.dtb \ ++ qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-u4019-32m.dtb \ + qcom-ipq4019-wpj419.dtb \ + qcom-ipq4028-wpj428.dtb \ |