diff options
Diffstat (limited to 'target')
9 files changed, 755 insertions, 1 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 097ba0afe1..2b259b9036 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -21,6 +21,10 @@ edgecore,ecw5410) ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy1tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt" ;; +meraki,mr52) + ucidef_set_led_netdev "eth0" "eth0" "green:lan1" "eth0" + ucidef_set_led_netdev "eth1" "eth1" "green:lan2" "eth1" + ;; nec,wg2600hp) ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy1tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 65a0e98b3b..4cb691f32e 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -44,6 +44,12 @@ linksys,ea8500) ucidef_set_interface_macaddr "lan" "$hw_mac_addr" ucidef_set_interface_macaddr "wan" "$hw_mac_addr" ;; +meraki,mr42) + ucidef_set_interface_lan "eth0" + ;; +meraki,mr52) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ;; nec,wg2600hp3) ucidef_add_switch "switch0" \ "2:lan" "3:lan" "4:lan" "5:lan" "0@eth1" "1:wan" "6@eth0" diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 8de4e052cc..78315d4516 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -7,6 +7,14 @@ board=$(board_name) case "$FIRMWARE" in +"ath10k/cal-pci-0000:01:00.0.bin") + case "$board" in + meraki,mr52) + CI_UBIPART=art + caldata_extract_ubi "ART" 0x1000 0x844 + ;; + esac + ;; "ath10k/pre-cal-pci-0000:01:00.0.bin") case $board in askey,rt4230w-rev6) @@ -26,6 +34,10 @@ case "$FIRMWARE" in caldata_extract "art" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) 1) ;; + meraki,mr42) + CI_UBIPART=art + caldata_extract_ubi "ART" 0x1000 0x2f20 + ;; netgear,d7800 |\ netgear,r7500v2 |\ netgear,r7800 |\ @@ -64,6 +76,11 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) 2) ;; + meraki,mr42 |\ + meraki,mr52) + CI_UBIPART=art + caldata_extract_ubi "ART" 0x5000 0x2f20 + ;; netgear,d7800 |\ netgear,r7500v2 |\ netgear,r7800 |\ @@ -80,11 +97,23 @@ case "$FIRMWARE" in ;; esac ;; +"ath10k/cal-pci-0002:01:00.0.bin") + case "$board" in + meraki,mr42) + CI_UBIPART=art + caldata_extract_ubi "ART" 0x9000 0x844 + ;; + esac + ;; "ath10k/pre-cal-pci-0002:01:00.0.bin") case $board in edgecore,ecw5410) caldata_extract "0:art" 0x5000 0x2f20 ;; + meraki,mr52) + CI_UBIPART=art + caldata_extract_ubi "ART" 0x9000 0x2f20 + ;; esac ;; *) diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 308d7017b3..3d96457dbd 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -45,6 +45,11 @@ platform_do_upgrade() { linksys,ea8500) platform_do_upgrade_linksys "$1" ;; + meraki,mr42 |\ + meraki,mr52) + CI_KERNPART="bootkernel2" + nand_do_upgrade "$1" + ;; tplink,ad7200 |\ tplink,c2600) PART_NAME="os-image:rootfs" diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-cryptid-common.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-cryptid-common.dtsi new file mode 100644 index 0000000000..10ab4821e8 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-cryptid-common.dtsi @@ -0,0 +1,239 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT + +#include "qcom-ipq8064-v2.0.dtsi" + +/ { + memory { + device_type = "memory"; + linux,usable-memory = <0x41500000 0x1ea00000>; + reg = <0x40000000 0x20000000>; + }; + + cpus { + idle-states { + CPU_SPC: spc { + status = "disabled"; + }; + }; + }; + + chosen { + bootargs-append = " console=ttyMSM0,115200n8 ubi.mtd=ubi ubi.mtd=art"; + }; +}; + +&qcom_pinmux { + mdio0_pins_active: mdio0_pins_active { + mux { + pins = "gpio0", "gpio1"; + function = "mdio"; + drive-strength = <2>; + bias-pull-down; + output-low; + }; + + clk { + pins = "gpio1"; + input-disable; + }; + }; + + phy_active: phy_active { + phy { + pins = "gpio6", "gpio7"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + output-high; + }; + }; + + uart1_pins: uart1_pins { + mux { + pins = "gpio51", "gpio52"; + function = "gsbi1"; + drive-strength = <4>; + bias-disable; + }; + }; +}; + +&gsbi1 { + status = "okay"; + qcom,mode = <GSBI_PROT_UART_W_FC>; + + serial@12450000 { + status = "okay"; + + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + }; +}; + +&pcie0 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; + + bridge@0,0 { + reg = <0x0 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi0: wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x10000 0 0 0 0>; + }; + }; +}; + +&pcie1 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; + + bridge@0,0 { + reg = <0x0 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi1: wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x10000 0 0 0 0>; + }; + }; +}; + +&pcie2 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; + + bridge@0,0 { + reg = <0x0 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x10000 0 0 0 0>; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + compatible = "qcom,nandcs"; + + reg = <0>; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + nand-is-boot-medium; + qcom,boot_pages_size = <0x2140000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "sbl1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "mibib"; + reg = <0x40000 0x140000>; + read-only; + }; + + partition@180000 { + label = "sbl2"; + reg = <0x180000 0x140000>; + read-only; + }; + + partition@2c0000 { + label = "sbl3"; + reg = <0x2c0000 0x280000>; + read-only; + }; + + partition@540000 { + label = "ddrconfig"; + reg = <0x540000 0x120000>; + read-only; + }; + + partition@660000 { + label = "ssd"; + reg = <0x660000 0x120000>; + read-only; + }; + + partition@780000 { + label = "tz"; + reg = <0x780000 0x280000>; + read-only; + }; + + partition@a00000 { + label = "rpm"; + reg = <0xa00000 0x280000>; + read-only; + }; + + partition@1fc0000 { + label = "u-boot"; + reg = <0x1fc0000 0x180000>; + read-only; + }; + + partition@21c0000 { + label = "bootkernel1"; + reg = <0x21c0000 0xa80000>; + }; + + partition@2c40000 { + label = "bootkernel2"; + reg = <0x2c40000 0xa80000>; + }; + + partition@36c0000 { + label = "ubi"; + reg = <0x36c0000 0x46c0000>; + }; + + partition@7d80000 { + label = "art"; + reg = <0x7d80000 0x200000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-mr42.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-mr42.dts new file mode 100644 index 0000000000..ccf2554ca3 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-mr42.dts @@ -0,0 +1,204 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT + +#include "qcom-ipq8068-cryptid-common.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Meraki MR42"; + compatible = "meraki,mr42", "qcom,ipq8064"; + + aliases { + serial1 = &gsbi1_serial; + ethernet0 = &gmac3; + + led-boot = &led_active; + led-failsafe = &led_power; + led-running = &led_active; + led-upgrade = &led_active; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + debounce-interval = <60>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_power: power { + label = "orange:power"; + gpios = <&qcom_pinmux 31 GPIO_ACTIVE_HIGH>; + }; + + led_active: active { + label = "white:active"; + gpios = <&qcom_pinmux 32 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&gmac3 { + status = "okay"; + + qcom,id = <3>; + mdiobus = <&mdio0>; + + phy-mode = "sgmii"; + phy-handle = <&phy2>; + + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; +}; + +&gsbi2 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C>; +}; + +&gsbi2_i2c { + status = "okay"; + + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + + ina2xx@40 { + compatible = "ina219"; + shunt-resistor = <40000>; + reg = <0x40>; + }; + + eeprom@56 { + compatible = "atmel,24c64"; + pagesize = <32>; + reg = <0x56>; + read-only; + #address-cells = <1>; + #size-cells = <1>; + + mac_address: mac-address@66 { + reg = <0x66 0x6>; + }; + }; +}; + +&gsbi6 { + qcom,mode = <GSBI_PROT_I2C>; + status = "okay"; +}; + +&gsbi6_i2c { + status = "okay"; + + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + tlc591xx@40 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,tlc59108"; + reg = <0x40>; + + red@0 { + label = "red:user"; + reg = <0x0>; + }; + + green@1 { + label = "green:user"; + reg = <0x1>; + }; + + blue@2 { + label = "blue:user"; + reg = <0x2>; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins_active>, <&phy_active>; + pinctrl-names = "default"; + + phy2: ethernet-phy2 { + reg = <2>; + + reset-gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + reset-assert-us = <24000>; + + eee-broken-100tx; + eee-broken-1000t; + }; +}; + +&qcom_pinmux { + i2c0_pins: i2c0_pins { + mux { + pins = "gpio24", "gpio25"; + function = "gsbi2"; + drive-strength = <2>; + bias-pull-up; + input; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio26"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + i2c1_pins: i2c1_pins { + mux { + pins = "gpio29", "gpio30"; + function = "gsbi6"; + drive-strength = <2>; + bias-pull-up; + input; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio31", "gpio32"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-low; + }; + }; +}; + +&wifi0 { + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; +}; + +&wifi1 { + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <2>; +}; + +&wifi2 { + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <3>; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-mr52.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-mr52.dts new file mode 100644 index 0000000000..e1c233254d --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-mr52.dts @@ -0,0 +1,230 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT + +#include "qcom-ipq8068-cryptid-common.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Meraki MR52"; + compatible = "meraki,mr52", "qcom,ipq8064"; + + aliases { + serial1 = &gsbi1_serial; + mdio-gpio0 = &mdio_gpio0; + ethernet0 = &gmac2; + ethernet1 = &gmac3; + + led-boot = &led_active; + led-failsafe = &led_power; + led-running = &led_active; + led-upgrade = &led_active; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + debounce-interval = <60>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_power: power { + label = "orange:power"; + gpios = <&qcom_pinmux 19 GPIO_ACTIVE_HIGH>; + }; + + lan2_green { + label = "green:lan2"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + lan1_green { + label = "green:lan1"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + + led_active: active { + label = "white:active"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + }; + + lan2_orange { + label = "orange:lan2"; + gpios = <&qcom_pinmux 60 GPIO_ACTIVE_HIGH>; + }; + + lan1_orange { + label = "orange:lan1"; + gpios = <&qcom_pinmux 62 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&gmac2 { + status = "okay"; + + qcom,id = <2>; + mdiobus = <&mdio0>; + + phy-mode = "sgmii"; + phy-handle = <&phy0>; + + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; +}; + +&gmac3 { + status = "okay"; + + qcom,id = <3>; + mdiobus = <&mdio_gpio0>; + + phy-mode = "sgmii"; + phy-handle = <&phy4>; + + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; +}; + +&gsbi7 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C>; +}; + +&gsbi7_i2c { + status = "okay"; + + pinctrl-0 = <&i2c_pins>; + pinctrl-names = "default"; + + ina2xx@45 { + compatible = "ina219"; + shunt-resistor = <80000>; + reg = <0x45>; + }; + + tlc591xx@49 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,tlc59108"; + reg = <0x49>; + + red@0 { + label = "red:user"; + reg = <0x0>; + }; + + green@1 { + label = "green:user"; + reg = <0x1>; + }; + + blue@2 { + label = "blue:user"; + reg = <0x2>; + }; + }; + + eeprom@52 { + compatible = "atmel,24c64"; + pagesize = <32>; + reg = <0x52>; + read-only; + #address-cells = <1>; + #size-cells = <1>; + + mac_address: mac-address@66 { + reg = <0x66 0x6>; + }; + }; +}; + +&qcom_pinmux { + i2c_pins: i2c_pins { + mux { + pins = "gpio8", "gpio9"; + function = "gsbi7"; + drive-strength = <2>; + bias-pull-up; + input; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio19", "gpio26"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-low; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio25"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + input; + }; + }; +}; + +&soc { + mdio_gpio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + status = "okay"; + + pinctrl-0 = <&mdio0_pins_active>, <&phy_active>; + pinctrl-names = "default"; + + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH + &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + + phy0: ethernet-phy0 { + reg = <0>; + reset-gpios = <&qcom_pinmux 7 GPIO_ACTIVE_LOW>; + reset-assert-us = <24000>; + }; + + phy4: ethernet-phy4 { + reg = <4>; + reset-gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + reset-assert-us = <24000>; + }; + }; +}; + +&wifi0 { + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <4>; +}; + +&wifi1 { + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <3>; +}; + +&wifi2 { + nvmem-cells = <&mac_address>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <2>; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index acb95347bf..fc0080cf84 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -192,6 +192,41 @@ define Device/linksys_ea8500 endef TARGET_DEVICES += linksys_ea8500 +define Device/meraki_mr42 + $(call Device/FitImage) + DEVICE_VENDOR := Cisco Meraki + DEVICE_MODEL := MR42 + SOC := qcom-ipq8068 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_LOADADDR = 0x44208000 + DEVICE_PACKAGES := -swconfig -kmod-ata-ahci -kmod-ata-ahci-platform \ + -kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \ + -kmod-phy-qcom-ipq806x-usb -kmod-usb3 -kmod-usb-dwc3-qcom \ + -uboot-envtools ath10k-firmware-qca9887-ct \ + ath10k-firmware-qca99x0-ct kmod-eeprom-at24 kmod-hwmon-ina2xx \ + kmod-leds-tlc591xx +endef +TARGET_DEVICES += meraki_mr42 + +define Device/meraki_mr52 + $(call Device/FitImage) + DEVICE_VENDOR := Cisco Meraki + DEVICE_MODEL := MR52 + SOC := qcom-ipq8068 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_LOADADDR = 0x44208000 + DEVICE_DTS_CONFIG := config@2 + DEVICE_PACKAGES := -swconfig -kmod-ata-ahci -kmod-ata-ahci-platform \ + -kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \ + -kmod-phy-qcom-ipq806x-usb -kmod-usb3 -kmod-usb-dwc3-qcom \ + -uboot-envtools ath10k-firmware-qca9887-ct \ + ath10k-firmware-qca9984-ct kmod-eeprom-at24 kmod-hwmon-ina2xx \ + kmod-leds-tlc591xx +endef +TARGET_DEVICES += meraki_mr52 + define Device/nec_wg2600hp $(call Device/LegacyImage) DEVICE_VENDOR := NEC diff --git a/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch index ca43a759ef..49ff218040 100644 --- a/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -907,8 +907,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -907,8 +907,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ @@ -35,6 +35,8 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq8065-rt4230w-rev6.dtb \ + qcom-ipq8065-xr500.dtb \ + qcom-ipq8068-ecw5410.dtb \ ++ qcom-ipq8068-mr42.dtb \ ++ qcom-ipq8068-mr52.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ qcom-msm8974-fairphone-fp2.dtb \ |