diff options
Diffstat (limited to 'target')
6 files changed, 377 insertions, 3 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 77a2241283..cd336a9e6a 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -75,7 +75,8 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan" ;; - glinet,gl-b1300) + glinet,gl-b1300 |\ + glinet,gl-s1300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index e41baecf69..b95bab7cae 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -50,6 +50,7 @@ case "$FIRMWARE" in cilab,meshpoint-one |\ ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ + glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) @@ -138,6 +139,7 @@ case "$FIRMWARE" in cilab,meshpoint-one |\ ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ + glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4029-gl-s1300.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4029-gl-s1300.dts new file mode 100644 index 0000000000..3457ebebfe --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4029-gl-s1300.dts @@ -0,0 +1,356 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "GL.iNet GL-S1300"; + compatible = "glinet,gl-s1300"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x18>; + switch_wan_bmp = <0x20>; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&tlmm 53 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "gl-s1300:green:power"; + gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + mesh { + label = "gl-s1300:green:mesh"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>; + }; + + wlan { + label = "gl-s1300:green:wlan"; + gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + }; +}; + +&vqmmc { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_pins>; + pinctrl-names = "default"; + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vqmmc>; +}; + +&blsp_dma { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + MIBIB@40000 { + label = "MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + QSEE@60000 { + label = "QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + CDT@c0000 { + label = "CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + DDRPARAMS@d0000 { + label = "DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + APPSBLENV@e0000 { + label = "APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + APPSBL@f0000 { + label = "APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + ART@170000 { + label = "ART"; + reg = <0x170000 0x10000>; + read-only; + }; + + firmware@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x180000 0xe80000>; + }; + }; + }; +}; + +&blsp1_spi2 { + pinctrl-0 = <&spi_1_pins>; + pinctrl-names = "default"; + status = "okay"; + + spidev1: spi@1 { + compatible = "siliconlabs,si3210"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", + "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + }; + pinconf { + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + spi_1_pins: spi_1_pinmux { + mux { + pins = "gpio44", "gpio46", "gpio47"; + function = "blsp_spi1"; + bias-disable; + }; + host_int { + pins = "gpio42"; + function = "gpio"; + input; + }; + cs { + pins = "gpio45"; + function = "gpio"; + bias-pull-up; + }; + wake { + pins = "gpio40"; + function = "gpio"; + output-high; + }; + reset { + pins = "gpio49"; + function = "gpio"; + output-high; + }; + }; + + sd_pins: sd_pins { + pinmux { + function = "sdio"; + pins = "gpio23", "gpio24", "gpio25", "gpio26", + "gpio28", "gpio29", "gpio30", "gpio31"; + drive-strength = <10>; + }; + + pinmux_sd_clk { + function = "sdio"; + pins = "gpio27"; + drive-strength = <16>; + }; + + pinmux_sd7 { + function = "sdio"; + pins = "gpio32"; + drive-strength = <10>; + bias-disable; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-S1300"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-S1300"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index a374c7da47..5336649c3d 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -437,6 +437,19 @@ define Device/glinet_gl-b1300 endef TARGET_DEVICES += glinet_gl-b1300 +define Device/glinet_gl-s1300 + $(call Device/FitImage) + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := GL-S1300 + SOC := qcom-ipq4029 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 26624k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev +endef +TARGET_DEVICES += glinet_gl-s1300 + define Device/linksys_ea6350v3 # The Linksys EA6350v3 has a uboot bootloader that does not # support either booting lzma kernel images nor booting UBI diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 2ec1007191..fb358ed184 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,47 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,48 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -54,6 +54,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 371faa3a09..2db36aa597 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,48 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,49 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -55,6 +55,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \ |