diff options
Diffstat (limited to 'target/linux')
10 files changed, 0 insertions, 735 deletions
diff --git a/target/linux/layerscape/base-files/etc/board.d/01_led b/target/linux/layerscape/base-files/etc/board.d/01_led index a21c21980a..8a0e5c4b95 100644 --- a/target/linux/layerscape/base-files/etc/board.d/01_led +++ b/target/linux/layerscape/base-files/etc/board.d/01_led @@ -9,14 +9,6 @@ board_config_update board=$(board_name) case "$board" in -traverse,ls1043v) - ucidef_set_led_netdev "wan" "WAN LED" "ls1043v:yellow:wan" "eth4" - ;; -traverse,ls1043s) - ucidef_set_led_netdev "wan" "WAN LED" "ls1043s:yellow:wan" "eth4" - ucidef_set_led_netdev "xgact" "10G Activity" "ls1043s:yellow:10gact" "eth6" - ucidef_set_led_netdev "xglink" "10G Link" "ls1043s:green:10glink" "eth6" - ;; traverse,ten64) ucidef_set_led_netdev "sfp1" "SFP 1" "ten64:green:sfp1:down" "eth8" "link tx rx" ucidef_set_led_netdev "sfp2" "SFP 2" "ten64:green:sfp2:up" "eth9" "link tx rx" diff --git a/target/linux/layerscape/base-files/etc/board.d/02_network b/target/linux/layerscape/base-files/etc/board.d/02_network index 7bc5f9b502..0a42323801 100644 --- a/target/linux/layerscape/base-files/etc/board.d/02_network +++ b/target/linux/layerscape/base-files/etc/board.d/02_network @@ -9,14 +9,6 @@ case "$(board_name)" in fsl,ls1028a-rdb-sdboot) ucidef_set_interfaces_lan_wan "swp0 swp1 swp2 swp3" "eth0" ;; - traverse,ls1043v) - ucidef_set_interface_lan "eth0 eth1 eth2 eth3" - ucidef_set_interface_wan "eth4" - ;; - traverse,ls1043s) - ucidef_set_interface_lan "eth0 eth1 eth2 eth3 eth6" - ucidef_set_interface_wan "eth4" - ;; traverse,ten64) ucidef_set_interface_lan "eth0 eth1 eth2 eth3" ucidef_set_interface_wan "eth6" diff --git a/target/linux/layerscape/base-files/etc/board.d/03_gpio_switches b/target/linux/layerscape/base-files/etc/board.d/03_gpio_switches index 5e0e24ef28..46e54b960d 100644 --- a/target/linux/layerscape/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/layerscape/base-files/etc/board.d/03_gpio_switches @@ -9,17 +9,6 @@ board_config_update board=$(board_name) case "$board" in -traverse,ls1043v) - ucidef_add_gpio_switch "lte_reset" "LTE Reset" "377" - ucidef_add_gpio_switch "lte_disable" "LTE Airplane mode" "378" - ;; -traverse,ls1043s) - ucidef_add_gpio_switch "tensfp_txdisable" "SFP+ TX Disable" "378" - ucidef_add_gpio_switch "gigsfp_txdisable" "SFP TX Disable" "381" - ucidef_add_gpio_switch "lte_reset" "LTE Reset" "502" - ucidef_add_gpio_switch "lte_disable" "LTE Airplane Mode" "394" - ucidef_add_gpio_switch "lte_power" "LTE Power" "395" - ;; traverse,ten64) ucidef_add_gpio_switch "lte_reset" "Cell Modem Reset" "376" ucidef_add_gpio_switch "lte_power" "Cell Modem Power" "377" diff --git a/target/linux/layerscape/base-files/lib/preinit/05_layerscape_reorder_eth b/target/linux/layerscape/base-files/lib/preinit/05_layerscape_reorder_eth deleted file mode 100644 index c6b741a5ce..0000000000 --- a/target/linux/layerscape/base-files/lib/preinit/05_layerscape_reorder_eth +++ /dev/null @@ -1,26 +0,0 @@ -reorder_layerscape_interfaces() { - if [ ! -f /tmp/sysinfo/board_name ]; then - echo "No board name found, not doing reorder_layerscape_interfaces" - return 0 - fi - - board=$(cat /tmp/sysinfo/board_name) - case "$board" in - traverse,ls1043v|\ - traverse,ls1043s) - - # Reorder ethernet interfaces to match the physical order - ip link set eth2 name fm1-mac3 - ip link set eth4 name eth2 - ip link set eth3 name fm1-mac4 - ip link set eth5 name eth3 - ip link set fm1-mac3 name eth4 - ip link set fm1-mac4 name eth5 - ;; - default) - echo "Unknown board $board" - ;; - esac -} - -boot_hook_add preinit_main reorder_layerscape_interfaces diff --git a/target/linux/layerscape/base-files/lib/upgrade/platform.sh b/target/linux/layerscape/base-files/lib/upgrade/platform.sh index c63cf05e5c..0b5d14b579 100644 --- a/target/linux/layerscape/base-files/lib/upgrade/platform.sh +++ b/target/linux/layerscape/base-files/lib/upgrade/platform.sh @@ -32,23 +32,6 @@ platform_do_upgrade_sdboot() { tar xf $tar_file ${board_dir}/root -O | dd of=/dev/mmcblk0p2 bs=512k > /dev/null 2>&1 } -platform_do_upgrade_traverse_nandubi() { - bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}') - newbootsys=2 - if [ "$bootsys" -eq "2" ]; then - newbootsys=1 - fi - - # If nand_do_upgrade succeeds, we don't have an opportunity to add any actions of - # our own, so do it here and set back on failure - echo "Setting bootsys to #${newbootsys}" - fw_setenv bootsys $newbootsys - CI_UBIPART="nandubi" - CI_KERNPART="kernel${newbootsys}" - CI_ROOTPART="rootfs${newbootsys}" - nand_do_upgrade "$1" || (echo "Upgrade failed, setting bootsys ${bootsys}" && fw_setenv bootsys $bootsys) - -} platform_do_upgrade_traverse_slotubi() { part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')" @@ -105,11 +88,6 @@ platform_check_image() { local board=$(board_name) case "$board" in - traverse,ls1043v | \ - traverse,ls1043s) - nand_do_platform_check "traverse-ls1043" $1 - return $? - ;; traverse,ten64) nand_do_platform_check "ten64-mtd" $1 return $? @@ -150,10 +128,6 @@ platform_do_upgrade() { touch /var/lock/fw_printenv.lock case "$board" in - traverse,ls1043v | \ - traverse,ls1043s) - platform_do_upgrade_traverse_nandubi "$1" - ;; traverse,ten64) platform_do_upgrade_traverse_slotubi "${1}" ;; diff --git a/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts b/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts deleted file mode 100644 index 81044aab3a..0000000000 --- a/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts +++ /dev/null @@ -1,332 +0,0 @@ -/* - * Device Tree Include file for Traverse LS1043S board. - * - * Copyright 2014-2015, Freescale Semiconductor - * Copyright 2017-2018, Traverse Technologies - * - * This file is dual-licensed: you can use it either under the terms - * of the GPLv2 or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This library is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This library is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/dts-v1/; -#include "fsl-ls1043a.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> - -/ { - model = "Traverse LS1043S"; - compatible = "traverse,ls1043s"; - - aliases { - crypto = &crypto; - ethernet0 = &EMAC0; - ethernet1 = &EMAC1; - ethernet2 = &EMAC2; - ethernet3 = &EMAC3; - ethernet4 = &EMAC4; - ethernet5 = &EMAC5; - }; - - leds { - compatible = "gpio-leds"; - gpio0 { - label = "ls1043s:green:user0"; - gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; - }; - gpio1 { - label = "ls1043s:green:user1"; - gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; - }; - /* LED D17 */ - gpio2 { - label = "ls1043s:green:wan"; - gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; - }; - gpio3 { - label = "ls1043s:yellow:wan"; - gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; - }; - /* LED D18 */ - gpio4 { - label = "ls1043s:green:mgmt"; - gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; - }; - gpio5 { - label = "ls1043s:yellow:mgmt"; - gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; - }; - /* LED D6 */ - gpio6 { - label = "ls1043s:green:user2"; - gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>; - }; - - /* SFP+ LEDs - these are for chassis - * with lightpipes only - */ - teng_act { - label = "ls1043s:yellow:10gact"; - gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; - }; - - teng_link { - label = "ls1043s:green:10glink"; - gpios = <&gpio4 1 GPIO_ACTIVE_LOW>; - }; - }; - - keys { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <1000>; - /* This button may not be loaded on all boards */ - button@0 { - label = "Front button"; - linux,code = <KEY_SETUP>; - gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; - }; - /* This is wired to header S3 */ - button@1 { - label = "Rear button"; - linux,code = <KEY_WPS_BUTTON>; - gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&esdhc { - mmc-hs200-1_8v; - sd-uhs-sdr104; - sd-uhs-sdr50; - sd-uhs-sdr25; - sd-uhs-sdr12; -}; - -&i2c0 { - status = "okay"; - rtc@6f { - compatible = "intersil,isl1208"; - reg = <0x6f>; - }; - - sfp_pca9534: pca9534@24 { - compatible = "ti,tca9534", "nxp,pca9534"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x24>; - gpio-base = <100>; - }; - - controller@50 { - compatible = "traverse,controller"; - reg = <0x50>; - }; - - ds125df111@18 { - compatible = "ti,ds125df111"; - reg = <0x18>; - }; - - emc1704@4c { - compatible = "microchip,emc1704"; - reg = <0x4c>; - }; - - pac1934@16 { - compatible = "microchip,pac1934"; - reg = <0x16>; - /* Monitoring 3.3V, 5V, Vin/12V (voltage only), Vbat/RTC (voltage only) */ - shunt-resistors = <4000 12000 0 0>; - }; - - pmic@8 { - compatible = "freescale,mc34vr500"; - reg = <0x08>; - }; -}; - -/* I2C Bus for SFP EEPROM and control - * These are multiplexed so - * they don't collide when loaded - */ -&i2c3 { - status = "okay"; - i2c-switch@70 { - compatible = "nxp,pca9540"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x70>; - - gigsfp_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - tensfp_i2c: i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - }; - }; -}; - -&ifc { - status = "okay"; - #address-cells = <2>; - #size-cells = <1>; - /* Only NAND flash is used on this board */ - ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>; - - nand@1,0 { - compatible = "fsl,ifc-nand"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x0 0x0 0x10000>; - }; -}; - -&duart0 { - status = "okay"; -}; - -&duart1 { - status = "okay"; -}; - -#include "fsl-ls1043-post.dtsi" - -&fman0 { - EMAC0: ethernet@e0000 { - phy-handle = <&qsgmii_phy1>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 01]; - }; - - EMAC1: ethernet@e2000 { - phy-handle = <&qsgmii_phy2>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 02]; - }; - - EMAC2: ethernet@e8000 { - phy-handle = <&qsgmii_phy3>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 03]; - }; - - EMAC3: ethernet@ea000 { - phy-handle = <&qsgmii_phy4>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 04]; - }; - - /* SFP via AR8031 - * We treat this as a fixed-link as the - * AR8031 is hard-configured into - * 1000BASE-X mode - * Should MII control be desired, remove - * fixed-link and add - * phy-handle = <&rgmii_phy1>; - */ - EMAC4: ethernet@e4000 { - phy-connection-type = "rgmii"; - local-mac-address = [0A 00 00 00 00 05]; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - /* Connection to Expansion (M.2) slot - * Future WAN (i.e xDSL) plugin - */ - EMAC5: ethernet@e6000 { - phy-connection-type = "rgmii-id"; - local-mac-address = [00 00 00 00 00 06]; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - /* 10G SFP+ interface - * This can also run at 1.25 and 2.5G with - * the appropriate SerDes protocol setting in RCW - */ - TENSFP: ethernet@f0000 { - status = "okay"; - phy-connection-type = "xgmii"; - fixed-link { - speed = <10000>; - full-duplex; - }; - }; - - mdio@fc000 { - rgmii_phy1: ethernet-phy@2 { - reg = <0x2>; - }; - qsgmii_phy1: ethernet-phy@4 { - reg = <0x4>; - }; - qsgmii_phy2: ethernet-phy@5 { - reg = <0x5>; - }; - qsgmii_phy3: ethernet-phy@6 { - reg = <0x6>; - }; - qsgmii_phy4: ethernet-phy@7 { - reg = <0x7>; - }; - }; -}; - -/* No QUICC engine functions on this board - - * pins are used for other functions (GPIO, I2C etc.) - */ -&uqe { - status = "disabled"; -}; - -/* LS1043S does not use the QorIQ AHCI - * controller. - */ -&sata { - status = "disabled"; -}; diff --git a/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts b/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts deleted file mode 100644 index 936875101f..0000000000 --- a/target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts +++ /dev/null @@ -1,253 +0,0 @@ -/* - * Device Tree Include file for Traverse LS1043V board. - * - * Copyright 2014-2015, Freescale Semiconductor - * Copyright 2017, Traverse Technologies - * - * This file is dual-licensed: you can use it either under the terms - * of the GPLv2 or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This library is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This library is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/dts-v1/; -#include "fsl-ls1043a.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> - -/ { - model = "Traverse LS1043V"; - compatible = "traverse,ls1043v"; - - aliases { - crypto = &crypto; - ethernet0 = &EMAC0; - ethernet1 = &EMAC1; - ethernet2 = &EMAC2; - ethernet3 = &EMAC3; - ethernet4 = &EMAC4; - ethernet5 = &EMAC5; - pca9555 = &pca9555; - }; - - leds { - compatible = "gpio-leds"; - gpio0 { - label = "ls1043v:green:user0"; - gpios = <&pca9555 0 GPIO_ACTIVE_LOW>; - }; - gpio1 { - label = "ls1043v:yellow:user0"; - gpios = <&pca9555 1 GPIO_ACTIVE_LOW>; - }; - gpio2 { - label = "ls1043v:green:user1"; - gpios = <&pca9555 2 GPIO_ACTIVE_LOW>; - }; - gpio3 { - label = "ls1043v:yellow:user1"; - gpios = <&pca9555 3 GPIO_ACTIVE_LOW>; - }; - gpio4 { - label = "ls1043v:green:user2"; - gpios = <&pca9555 4 GPIO_ACTIVE_HIGH>; - }; - gpio5 { - label = "ls1043v:yellow:wlan"; - gpios = <&pca9555 5 GPIO_ACTIVE_HIGH>; - }; - gpio6 { - label = "ls1043v:yellow:wan"; - gpios = <&pca9555 6 GPIO_ACTIVE_HIGH>; - }; - }; - - keys { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <1000>; - button@0 { - label = "Front button"; - linux,code = <KEY_SETUP>; - gpios = <&pca9555 14 GPIO_ACTIVE_LOW>; - }; - button@1 { - label = "Rear button"; - linux,code = <KEY_WPS_BUTTON>; - gpios = <&pca9555 15 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&i2c0 { - status = "okay"; - rtc@6f { - compatible = "intersil,isl1208"; - reg = <0x6f>; - }; - - pca9555: pca9555@20 { - compatible = "nxp,pca9555"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x20>; - gpio-base = <0>; - }; - - /* CPU core temp sensor and VDD (1.0V) sensor */ - ltc2990@4c { - compatible = "lltc,ltc2990"; - reg = <0x4C>; - lltc,meas-mode = <4 3>; - }; - - /* 3.3V and 5V monitor (may not be loaded on some SKUs) */ - ltc2990@4f { - compatible = "lltc,ltc2990"; - reg = <0x4F>; - lltc,meas-mode = <6 3>; - }; -}; - -&ifc { - status = "okay"; - #address-cells = <2>; - #size-cells = <1>; - /* Only NAND flash is used on this board */ - ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>; - - nand@1,0 { - compatible = "fsl,ifc-nand"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x0 0x0 0x10000>; - }; -}; - -&duart0 { - status = "okay"; -}; - -&duart1 { - status = "okay"; -}; - -#include "fsl-ls1043-post.dtsi" - -&fman0 { - EMAC0: ethernet@e0000 { - phy-handle = <&qsgmii_phy1>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 01]; - }; - - EMAC1: ethernet@e2000 { - phy-handle = <&qsgmii_phy2>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 02]; - }; - - EMAC2: ethernet@e8000 { - phy-handle = <&qsgmii_phy3>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 03]; - }; - - EMAC3: ethernet@ea000 { - phy-handle = <&qsgmii_phy4>; - phy-connection-type = "qsgmii"; - local-mac-address = [0A 00 00 00 00 04]; - }; - EMAC4: ethernet@e4000 { - phy-handle = <&rgmii_phy1>; - phy-connection-type = "rgmii"; - local-mac-address = [0A 00 00 00 00 05]; - }; - - /* Connection to VDSL SoC */ - EMAC5: ethernet@e6000 { - phy-connection-type = "rgmii-id"; - local-mac-address = [00 00 00 00 00 06]; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - /* 10G XFI interface - not in use on this platform */ - TENSFP: ethernet@f0000 { - status = "disabled"; - - phy-connection-type = "sgmii"; - fixed-link { - /* NB: speed = 1000 and sgmii allows forward compatibility - * with both 1G and 10G, the same is not true - * in the reverse. - */ - speed = <1000>; - full-duplex; - }; - }; - - mdio@fc000 { - rgmii_phy1: ethernet-phy@3 { - reg = <0x3>; - }; - qsgmii_phy1: ethernet-phy@4 { - reg = <0x4>; - }; - qsgmii_phy2: ethernet-phy@5 { - reg = <0x5>; - }; - qsgmii_phy3: ethernet-phy@6 { - reg = <0x6>; - }; - qsgmii_phy4: ethernet-phy@7 { - reg = <0x7>; - }; - }; -}; - -/* No QUICC engine functions on this board */ -&uqe { - status = "disabled"; -}; - -/* No SATA/AHCI on this board */ -&sata { - status = "disabled"; -}; diff --git a/target/linux/layerscape/image/Makefile b/target/linux/layerscape/image/Makefile index 1463a3eaea..dfbda85b36 100644 --- a/target/linux/layerscape/image/Makefile +++ b/target/linux/layerscape/image/Makefile @@ -51,19 +51,6 @@ define Build/ls-append-sdhead dd if=$(STAGING_DIR_IMAGE)/$(1)-sdcard-head.img >> $@ endef -define Build/traverse-fit - ./mkits-multiple-config.sh -o $@.its -A $(LINUX_KARCH) \ - -v $(LINUX_VERSION) -k $@ -a $(KERNEL_LOADADDR) \ - -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \ - -C gzip -c 1 -c 2 \ - -d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043s.dtb \ - -D "Traverse_LS1043S" -n "ls1043s" -a $(FDT_LOADADDR) -c 1 \ - -d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043v.dtb \ - -D "Traverse_LS1043V" -n "ls1043v" -a $(FDT_LOADADDR) -c 2 - PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new - @mv -f $@.new $@ -endef - define Build/traverse-fit-ls1088 ./mkits-multiple-config.sh -o $@.its -A $(LINUX_KARCH) \ -v $(LINUX_VERSION) -k $@ -a $(KERNEL_LOADADDR) \ diff --git a/target/linux/layerscape/image/armv8_64b.mk b/target/linux/layerscape/image/armv8_64b.mk index 0016e3bde8..259bacee31 100644 --- a/target/linux/layerscape/image/armv8_64b.mk +++ b/target/linux/layerscape/image/armv8_64b.mk @@ -420,38 +420,6 @@ define Device/fsl_lx2160a-rdb-sdboot endef TARGET_DEVICES += fsl_lx2160a-rdb-sdboot -define Device/traverse_ls1043 - DEVICE_VENDOR := Traverse - DEVICE_MODEL := LS1043 Boards - KERNEL_NAME := Image - KERNEL_SUFFIX := -kernel.itb - KERNEL_INSTALL := 1 - FDT_LOADADDR = 0x90000000 - FILESYSTEMS := ubifs - MKUBIFS_OPTS := -m 1 -e 262016 -c 128 - DEVICE_PACKAGES += \ - layerscape-fman \ - uboot-envtools \ - kmod-i2c-mux-pca954x \ - kmod-hwmon-core \ - kmod-gpio-pca953x kmod-input-gpio-keys-polled \ - kmod-rtc-isl1208 - DEVICE_DESCRIPTION = \ - Build images for Traverse LS1043 boards. This generates a single image \ - capable of booting on any of the boards in this family. - DEVICE_DTS = freescale/traverse-ls1043s - DEVICE_DTS_DIR = $(LINUX_DIR)/arch/arm64/boot/dts - DEVICE_DTS_CONFIG = ls1043s - KERNEL := kernel-bin | gzip | traverse-fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb - KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb - IMAGES = root sysupgrade.bin - IMAGE/root = append-rootfs - IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata - MKUBIFS_OPTS := -m 2048 -e 124KiB -c 4096 - SUPPORTED_DEVICES := traverse,ls1043s traverse,ls1043v -endef -TARGET_DEVICES += traverse_ls1043 - define Device/traverse_ten64_mtd DEVICE_VENDOR := Traverse DEVICE_MODEL := Ten64 (NAND boot) diff --git a/target/linux/layerscape/patches-5.15/300-add-DTS-for-Traverse-LS1043-Boards.patch b/target/linux/layerscape/patches-5.15/300-add-DTS-for-Traverse-LS1043-Boards.patch deleted file mode 100644 index 110afedefd..0000000000 --- a/target/linux/layerscape/patches-5.15/300-add-DTS-for-Traverse-LS1043-Boards.patch +++ /dev/null @@ -1,26 +0,0 @@ -From 5b35aae22b4ca2400e49561c9267aa01346f91d4 Mon Sep 17 00:00:00 2001 -From: Mathew McBride <matt@traverse.com.au> -Date: Tue, 17 Apr 2018 10:01:03 +1000 -Subject: [PATCH] add DTS for Traverse LS1043 Boards - -Signed-off-by: Mathew McBride <matt@traverse.com.au> -[rebase] -Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> ---- - arch/arm64/boot/dts/freescale/Makefile | 3 +++ - arch/arm64/boot/dts/freescale/traverse-ls1043s.dts | 29 ++++++++++++++++++++++ - arch/arm64/boot/dts/freescale/traverse-ls1043v.dts | 29 ++++++++++++++++++++++ - 3 files changed, 61 insertions(+) - ---- a/arch/arm64/boot/dts/freescale/Makefile -+++ b/arch/arm64/boot/dts/freescale/Makefile -@@ -31,6 +31,9 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2 - dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb - dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb - -+dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043v.dtb -+dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043s.dtb -+ - dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb - dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb - dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb |