aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux')
-rw-r--r--target/linux/mvebu/config-5.103
-rw-r--r--target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds4
-rw-r--r--target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network7
-rwxr-xr-xtarget/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh13
-rw-r--r--target/linux/mvebu/files/arch/arm/boot/dts/armada-370-c200-v2.dts426
-rw-r--r--target/linux/mvebu/image/Makefile57
-rw-r--r--target/linux/mvebu/image/cortexa9.mk18
7 files changed, 527 insertions, 1 deletions
diff --git a/target/linux/mvebu/config-5.10 b/target/linux/mvebu/config-5.10
index a3fcbeb699..33cb8cce88 100644
--- a/target/linux/mvebu/config-5.10
+++ b/target/linux/mvebu/config-5.10
@@ -337,6 +337,9 @@ CONFIG_PJ4B_ERRATA_4742=y
CONFIG_PL310_ERRATA_753970=y
CONFIG_PLAT_ORION=y
CONFIG_PM_OPP=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO=y
+# CONFIG_POWER_RESET_QNAP is not set
CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT=11
CONFIG_PWM=y
CONFIG_PWM_SYSFS=y
diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds b/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
index 381596d85d..161d111ea7 100644
--- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
+++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
@@ -11,6 +11,10 @@ board=$(board_name)
boardname="${board##*,}"
case "$board" in
+ctera,c200-v2
+ ucidef_set_led_usbport "usb2" "USB2" "green:usb-2" "usb1-port1" "usb2-port1"
+ ucidef_set_led_usbport "usb3" "USB3" "green:usb-1" "usb1-port2" "usb2-port2"
+ ;;
kobol,helios4)
ucidef_set_led_usbport "USB" "USB" "helios4:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" "usb5-port1"
;;
diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
index ad61dbea43..36769e8c18 100644
--- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
+++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
@@ -12,6 +12,9 @@ mvebu_setup_interfaces()
local board="$1"
case "$board" in
+ ctera,c200-v2)
+ ucidef_set_interface_lan "eth0" "dhcp"
+ ;;
cznic,turris-omnia)
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" "eth2"
;;
@@ -58,6 +61,10 @@ mvebu_setup_macs()
buffalo,ls421de)
lan_mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
;;
+ ctera,c200-v2)
+ label_mac=$(mtd_get_mac_ascii dev_params mac)
+ lan_mac=$label_mac
+ ;;
linksys,wrt1200ac|\
linksys,wrt1900ac-v2|\
linksys,wrt1900acs|\
diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
index 5e69374837..030e66e699 100755
--- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
@@ -3,7 +3,7 @@
# Copyright (C) 2016 LEDE-Project.org
#
-RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_BIN='fw_printenv fw_setenv strings'
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
REQUIRE_IMAGE_METADATA=1
@@ -26,6 +26,17 @@ platform_do_upgrade() {
buffalo,ls421de)
nand_do_upgrade "$1"
;;
+ ctera,c200-v2)
+ part=$(find_mtd_part "active_bank")
+
+ if [ -n "$part" ]; then
+ CI_KERNPART="$(strings $part | grep bank)"
+ nand_do_upgrade "$1"
+ else
+ echo "active_bank partition missed!"
+ return 1
+ fi
+ ;;
cznic,turris-omnia|\
kobol,helios4|\
solidrun,clearfog-base-a1|\
diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/armada-370-c200-v2.dts b/target/linux/mvebu/files/arch/arm/boot/dts/armada-370-c200-v2.dts
new file mode 100644
index 0000000000..c1c227a5e9
--- /dev/null
+++ b/target/linux/mvebu/files/arch/arm/boot/dts/armada-370-c200-v2.dts
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Device Tree file for Ctera C200-V2
+ *
+ * Copyright (C) 2021 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Ctera C200 V2";
+ compatible = "ctera,c200-v2", "marvell,armada370", "marvell,armada-370-xp";
+
+ aliases {
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_red;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>; /* 1024 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
+ };
+
+ thermal-zones {
+ ethphy-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <2000>;
+
+ thermal-sensors = <&ethphy0>;
+
+ trips {
+ ethphy_alert1: trip1 {
+ temperature = <65000>;
+ hysteresis = <4000>;
+ type = "passive";
+ };
+
+ ethphy_crit: trip2 {
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_buttons>;
+ pinctrl-names = "default";
+
+ power {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ };
+
+ usb1 {
+ label = "USB1 Button";
+ linux,code = <BTN_0>;
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ };
+
+ usb2 {
+ label = "USB2 Button";
+ linux,code = <BTN_1>;
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
+ pinctrl-names = "default";
+
+ led-0 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-1 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&usb1_port 1>, <&usb2_port 1>;
+ };
+
+ led-2 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&usb1_port 2>, <&usb2_port 2>;
+ };
+
+ led-4 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata2";
+ };
+
+ led-5 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ };
+
+ led-6 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ };
+
+ led-7 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-8 {
+ function = LED_FUNCTION_DISK_ERR;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ };
+
+ led-9 {
+ function = LED_FUNCTION_DISK_ERR;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_red: led-10 {
+ label = "red:status";
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
+ };
+
+ led-11 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata1";
+ };
+
+ led_status_green: led-12 {
+ label = "green:status";
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&coherencyfab {
+ broken-idle;
+};
+
+&eth1 {
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy-handle = <&ethphy0>;
+ phy-connection-type = "rgmii-id";
+};
+
+&i2c0 {
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ clock-frequency = <100000>;
+ status = "okay";
+
+ hwmon@2a {
+ compatible = "nuvoton,nct7802";
+ reg = <0x2a>;
+ };
+
+ rtc@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+};
+
+&mdio {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&nand_controller {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ label = "pxa3xx_nand-0";
+ nand-rb = <0>;
+ marvell,nand-keep-config;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x200000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "certificate";
+ reg = <0x0200000 0x100000>;
+ read-only;
+ };
+
+ partition@300000 {
+ label = "preset_cfg";
+ reg = <0x0300000 0x100000>;
+ read-only;
+ };
+
+ partition@400000 {
+ label = "dev_params";
+ reg = <0x0400000 0x100000>;
+ read-only;
+ };
+ partition@500000 {
+ label = "active_bank";
+ reg = <0x0500000 0x0100000>;
+ };
+
+ partition@600000 {
+ label = "magic";
+ reg = <0x0600000 0x0100000>;
+ read-only;
+ };
+
+ partition@700000 {
+ label = "bank1";
+ reg = <0x0700000 0x2800000>;
+ };
+
+ partition@2f00000 {
+ label = "bank2";
+ reg = <0x2f00000 0x2800000>;
+ };
+
+ /* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+ partition@5a00000 {
+ label = "reserved";
+ reg = <0x5a00000 0x2000000>;
+ };
+
+ partition@7a00000 {
+ label = "ubi";
+ reg = <0x7a00000 0x8600000>;
+ };
+ };
+ };
+};
+
+&pciec {
+ status = "okay";
+
+ pcie@1,0 {
+ pinctrl-0 = <&pmx_pcie>;
+ pinctrl-names = "default";
+ status = "okay";
+ reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+
+ /* -[0000:00]---01.0-[01]----00.0 */
+ /* usbport trigger won't work */
+ bridge@0,1 {
+ compatible = "pci11ab,6710";
+ reg = <0x3800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ usb@1,0 {
+ /* Renesas uPD720202 */
+ compatible = "pci1912,0015";
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ usb1_port: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <1>;
+ };
+
+ usb2_port: port@2 {
+ reg = <2>;
+ #trigger-source-cells = <1>;
+ };
+ };
+ };
+ };
+};
+
+&pinctrl {
+ pmx_poweroff: pmx-poweroff {
+ marvell,pins = "mpp7";
+ marvell,function = "gpo";
+ };
+
+ pmx_power_cpu: pmx-power-cpu {
+ marvell,pins = "mpp4";
+ marvell,function = "vdd";
+ };
+
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp6", "mpp10", "mpp14", "mpp32";
+ marvell,function = "gpio";
+ };
+
+ pmx_leds1: pmx-leds1 {
+ marvell,pins = "mpp47";
+ marvell,function = "gpo";
+ };
+
+ pmx_leds2: pmx-leds2 {
+ marvell,pins = "mpp12", "mpp13", "mpp15", "mpp16", "mpp50", "mpp51",
+ "mpp52", "mpp53", "mpp55", "mpp56", "mpp57", "mpp58";
+ marvell,function = "gpio";
+ };
+
+ pmx_pcie: pmx-pcie {
+ marvell,pins = "mpp59";
+ marvell,function = "gpio";
+ };
+
+ /* this gpio is connected to the pin of buzzer
+ * leave it as is due lack of proper driver
+ */
+ pmx_buzzer: pmx-buzzer {
+ marvell,pins = "mpp63";
+ marvell,function = "gpio";
+ };
+};
+
+&pmsu {
+ pinctrl-0 = <&pmx_power_cpu>;
+ pinctrl-names = "default";
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&sata {
+ nr-ports = <2>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdd0_temp: sata-port@0 {
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ hdd1_temp: sata-port@1 {
+ reg = <1>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/target/linux/mvebu/image/Makefile b/target/linux/mvebu/image/Makefile
index 9220c6c9f1..44e66a5f87 100644
--- a/target/linux/mvebu/image/Makefile
+++ b/target/linux/mvebu/image/Makefile
@@ -51,6 +51,63 @@ define Build/buffalo-kernel-jffs2
rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
endef
+# Some info about Ctera firmware:
+# 1. It's simple tar file (GNU standard), but it must have ".firm" suffix.
+# 2. It contains two images: kernel and romdisk. Both are required.
+# 3. Every image has header and trailer file.
+# 4. The struct of tar firmware is: header kernel trailer header romdisk trailer
+# 5. In header file are some strings used to describe image. It was decoded from
+# factory image.
+# 6. Version format in header file is restricted by Original FW.
+# 7. Trailer file contains MD5 sum string of header and image file.
+# 8. Firmware file must have <=24MB size.
+
+define Build/ctera-firmware
+ mkdir -p $@.tmp
+
+ # Prepare header and trailer file for kernel
+ echo "# CTera firmware information file" > $@.tmp/header
+ echo "image_type=kernel" >> $@.tmp/header
+ echo "arch=ARM" >> $@.tmp/header
+ echo "board=2Drive_A" >> $@.tmp/header
+ echo "version=5.5.165.61499" >> $@.tmp/header
+ echo "kernel_cmd=console=ttyS0,115200 earlycon" >> $@.tmp/header
+ echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
+ >> $@.tmp/header
+
+ cp $@ $@.tmp/kernel
+
+ echo "MD5=$$(cat $@.tmp/header $@.tmp/kernel | $(MKHASH) md5)" \
+ > $@.tmp/trailer
+
+ tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
+ -H gnu -C $@.tmp -cf $@.tar header kernel trailer
+
+ # Prepare header and trailer file for fake romdisk
+ echo "# CTera firmware information file" > $@.tmp/header
+ echo "image_type=romdisk" >> $@.tmp/header
+ echo "initrd=yes" >> $@.tmp/header
+ echo "arch=ARM" >> $@.tmp/header
+ echo "board=2Drive_A" >> $@.tmp/header
+ echo "version=5.5.165.61499" >> $@.tmp/header
+ echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
+ >> $@.tmp/header
+
+ rm -f $@
+ touch $@
+ $(call Build/append-uImage-fakehdr, ramdisk)
+ cp $@ $@.tmp/romdisk
+
+ echo "MD5=$$(cat $@.tmp/header $@.tmp/romdisk | $(MKHASH) md5)" \
+ > $@.tmp/trailer
+
+ tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
+ -H gnu -C $@.tmp -rf $@.tar header romdisk trailer
+
+ mv $@.tar $@
+ rm -rf $@.tmp
+endef
+
define Build/sdcard-img
SIGNATURE="$(IMG_PART_SIGNATURE)" \
./gen_mvebu_sdcard_img.sh $@ \
diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk
index 3f227259ee..06252670ab 100644
--- a/target/linux/mvebu/image/cortexa9.mk
+++ b/target/linux/mvebu/image/cortexa9.mk
@@ -31,6 +31,24 @@ define Device/buffalo_ls421de
endef
TARGET_DEVICES += buffalo_ls421de
+define Device/ctera_c200-v2
+ PAGESIZE := 2048
+ SUBPAGESIZE := 512
+ BLOCKSIZE := 128k
+ DEVICE_VENDOR := Ctera
+ DEVICE_MODEL := C200
+ DEVICE_VARIANT := V2
+ SOC := armada-370
+ KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
+ KERNEL_IN_UBI :=
+ KERNEL_SUFFIX := -factory.firm
+ DEVICE_PACKAGES := \
+ kmod-gpio-button-hotplug kmod-hwmon-drivetemp kmod-hwmon-nct7802 \
+ kmod-rtc-s35390a kmod-usb3 kmod-usb-ledtrig-usbport
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += ctera_c200-v2
+
define Device/cznic_turris-omnia
DEVICE_VENDOR := CZ.NIC
DEVICE_MODEL := Turris Omnia