diff options
Diffstat (limited to 'target/linux')
| -rw-r--r-- | target/linux/at91/image/Config.in | 27 | ||||
| -rw-r--r-- | target/linux/at91/image/Makefile | 10 | ||||
| -rw-r--r-- | target/linux/at91/image/u-boot/Makefile | 51 | ||||
| -rw-r--r-- | target/linux/at91/image/u-boot/patches/100-netusg20.patch | 574 | ||||
| -rw-r--r-- | target/linux/at91/image/u-boot/patches/200-clock.patch | 24 | ||||
| -rw-r--r-- | target/linux/at91/image/u-boot/ubclient/Makefile | 15 | ||||
| -rw-r--r-- | target/linux/at91/image/u-boot/ubclient/ubpar.c | 135 |
7 files changed, 0 insertions, 836 deletions
diff --git a/target/linux/at91/image/Config.in b/target/linux/at91/image/Config.in index 54a501dcb3..596accaa49 100644 --- a/target/linux/at91/image/Config.in +++ b/target/linux/at91/image/Config.in @@ -3,33 +3,6 @@ config AT91_DFBOOT depends on TARGET_at91 default n -config AT91_UBOOT - bool "Build U-Boot bootloader" - depends on TARGET_at91 - default n - -config UBOOT_TARGET - string "U-Boot target board" - depends on AT91_UBOOT - default "netusg20" - help - For all supported boards there are ready-to-use default - configurations available; just type "<board_name>". - -config UBOOT_IPADDR - string "IP Address for U-Boot" - depends on AT91_UBOOT - default "192.168.0.178" - help - IP address of device to be used in U-Boot - -config UBOOT_SERVERIP - string "IP Address of TFTP server" - depends on AT91_UBOOT - default "192.168.0.232" - help - IP address of TFTP server for U-Boot - config FLEXIBITY_ROOT bool "Build Flexibity RootFS (with embedded kernel)" depends on TARGET_at91_flexibity diff --git a/target/linux/at91/image/Makefile b/target/linux/at91/image/Makefile index 767255ca3f..0a4c95de7f 100644 --- a/target/linux/at91/image/Makefile +++ b/target/linux/at91/image/Makefile @@ -13,16 +13,6 @@ UBI_OPTS = -m 2048 -p 128KiB -s 512 AT91SAMA5D3XPLAINED_UBIFS_OPTS = -m 2048 -e 124KiB -c 2048 AT91SAMA5D3XPLAINED_UBI_OPTS = -m 2048 -p 128KiB -s 2048 -define Build/Clean - $(MAKE) -C u-boot clean -endef - -define Build/Compile - if [ $(CONFIG_AT91_UBOOT) ]; then \ - $(MAKE) -C u-boot compile; \ - fi -endef - define Image/Prepare cp $(LINUX_DIR)/arch/arm/boot/Image $(KDIR)/Image cp $(LINUX_DIR)/arch/arm/boot/zImage $(KDIR)/zImage diff --git a/target/linux/at91/image/u-boot/Makefile b/target/linux/at91/image/u-boot/Makefile deleted file mode 100644 index 1d1b31455a..0000000000 --- a/target/linux/at91/image/u-boot/Makefile +++ /dev/null @@ -1,51 +0,0 @@ -# -# Copyright (C) 2006 OpenWrt.org -# -# This is free software, licensed under the GNU General Public License v2. -# See /LICENSE for more information. -# - -include $(TOPDIR)/rules.mk -include $(INCLUDE_DIR)/kernel.mk - -PKG_NAME:=u-boot -PKG_VERSION:=2010.06 -PKG_RELEASE:=1 - -PKG_BUILD_DIR:=$(KERNEL_BUILD_DIR)/$(PKG_NAME)-$(PKG_VERSION) -PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.bz2 -PKG_SOURCE_URL:=ftp://ftp.denx.de/pub/u-boot -PKG_MD5SUM:= -PKG_CAT:=bzcat - -include $(INCLUDE_DIR)/package.mk - -UBOOT_CONFIG=$(call qstrip,$(CONFIG_UBOOT_TARGET)) -LAN_IP=$(call qstrip,$(CONFIG_UBOOT_IPADDR)) -LAN_SERVERIP=$(call qstrip,$(CONFIG_UBOOT_SERVERIP)) - -define Build/Compile - $(MAKE) -C $(PKG_BUILD_DIR) $(UBOOT_CONFIG)_config - export CROSS_COMPILE=$(TARGET_CROSS); \ - export LAN_IP=$(LAN_IP); \ - export LAN_SERVERIP=$(LAN_SERVERIP); \ - $(MAKE) -C $(PKG_BUILD_DIR) - mkdir -p $(PKG_BUILD_DIR)/ubclient - $(CP) ./ubclient/* $(PKG_BUILD_DIR)/ubclient - export LAN_IP=$(LAN_IP); \ - export LAN_SERVERIP=$(LAN_SERVERIP); \ - #$(MAKE) -C $(PKG_BUILD_DIR)/ubclient \ - # $(TARGET_CONFIGURE_OPTS) \ - # CFLAGS="$(TARGET_CFLAGS) -Dtarget_$(BOARD)=1" -endef - -define Build/InstallDev - dd if=$(PKG_BUILD_DIR)/u-boot.bin of=$(PKG_BUILD_DIR)/u-boot.block bs=232k count=1 conv=sync -# $(INSTALL_DIR) $(STAGING_DIR)/ubclient/sbin -# $(INSTALL_BIN) $(PKG_BUILD_DIR)/ubclient/ubpar $(STAGING_DIR)/ubclient/sbin/ -# $(CP) $(PKG_BUILD_DIR)/ubclient/ubpar ../../base-files/sbin - mkdir -p $(BIN_DIR)/ - cp $(PKG_BUILD_DIR)/u-boot.bin $(BIN_DIR)/u-boot.$(PKG_VERSION).bin -endef - -$(eval $(call Build/DefaultTargets)) diff --git a/target/linux/at91/image/u-boot/patches/100-netusg20.patch b/target/linux/at91/image/u-boot/patches/100-netusg20.patch deleted file mode 100644 index 127372e8f3..0000000000 --- a/target/linux/at91/image/u-boot/patches/100-netusg20.patch +++ /dev/null @@ -1,574 +0,0 @@ -Add support for the NetusG20 board by Acmesystems srl. -This board is based on AT91SAM9G20 SoC. - -Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com> ---- - MAKEALL | 1 + - Makefile | 3 + - arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c | 5 + - board/acmesystems/netusg20/Makefile | 56 +++++++ - board/acmesystems/netusg20/config.mk | 1 + - board/acmesystems/netusg20/led.c | 40 +++++ - board/acmesystems/netusg20/netusg20.c | 152 +++++++++++++++++ - board/acmesystems/netusg20/partition.c | 39 +++++ - include/configs/netusg20.h | 181 +++++++++++++++++++++ - 9 files changed, 478 insertions(+), 0 deletions(-) - create mode 100644 board/acmesystems/netusg20/Makefile - create mode 100644 board/acmesystems/netusg20/config.mk - create mode 100644 board/acmesystems/netusg20/led.c - create mode 100644 board/acmesystems/netusg20/netusg20.c - create mode 100644 board/acmesystems/netusg20/partition.c - create mode 100644 include/configs/netusg20.h - -diff --git a/MAKEALL b/MAKEALL -index d6d5f5b..60e36e1 100755 ---- a/MAKEALL -+++ b/MAKEALL -@@ -684,6 +684,7 @@ LIST_at91=" \ - meesc \ - mp2usb \ - m501sk \ -+ netusg20 \ - otc570 \ - pm9261 \ - pm9263 \ -diff --git a/Makefile b/Makefile -index 87d5214..b73659f 100644 ---- a/Makefile -+++ b/Makefile -@@ -2867,6 +2867,9 @@ at91sam9g45ekes_config : unconfig - fi; - @$(MKCONFIG) -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91 - -+netusg20_config: unconfig -+ @$(MKCONFIG) $(@:_config=) arm arm926ejs netusg20 acmesystems at91 -+ - otc570_config : unconfig - @$(MKCONFIG) $(@:_config=) arm arm926ejs otc570 esd at91 - -diff --git a/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c b/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c -index 77d49ab..87ec531 100644 ---- a/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c -+++ b/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c -@@ -59,7 +59,12 @@ void at91_serial3_hw_init(void) - { - at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; - -+#ifdef CONFIG_NETUSG20 -+ /* pull-up active on DRXD*/ -+ at91_set_a_periph(AT91_PIO_PORTB, 14, 1); -+#else - at91_set_a_periph(AT91_PIO_PORTB, 14, 0); /* DRXD */ -+#endif - at91_set_a_periph(AT91_PIO_PORTB, 15, 1); /* DTXD */ - writel(1 << AT91_ID_SYS, &pmc->pcer); - } -diff --git a/board/acmesystems/netusg20/Makefile b/board/acmesystems/netusg20/Makefile -new file mode 100644 -index 0000000..31589fd ---- /dev/null -+++ b/board/acmesystems/netusg20/Makefile -@@ -0,0 +1,56 @@ -+# -+# (C) Copyright 2003-2008 -+# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -+# -+# (C) Copyright 2008 -+# Stelian Pop <stelian.pop@leadtechdesign.com> -+# Lead Tech Design <www.leadtechdesign.com> -+# -+# See file CREDITS for list of people who contributed to this -+# project. -+# -+# This program is free software; you can redistribute it and/or -+# modify it under the terms of the GNU General Public License as -+# published by the Free Software Foundation; either version 2 of -+# the License, or (at your option) any later version. -+# -+# This program is distributed in the hope that it will be useful, -+# but WITHOUT ANY WARRANTY; without even the implied warranty of -+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+# GNU General Public License for more details. -+# -+# You should have received a copy of the GNU General Public License -+# along with this program; if not, write to the Free Software -+# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -+# MA 02111-1307 USA -+# -+ -+include $(TOPDIR)/config.mk -+ -+LIB = $(obj)lib$(BOARD).a -+ -+COBJS-y += netusg20.o -+COBJS-y += led.o -+COBJS-y += partition.o -+ -+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) -+OBJS := $(addprefix $(obj),$(COBJS-y)) -+SOBJS := $(addprefix $(obj),$(SOBJS)) -+ -+$(LIB): $(obj).depend $(OBJS) $(SOBJS) -+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) -+ -+clean: -+ rm -f $(SOBJS) $(OBJS) -+ -+distclean: clean -+ rm -f $(LIB) core *.bak $(obj).depend -+ -+######################################################################### -+ -+# defines $(obj).depend target -+include $(SRCTREE)/rules.mk -+ -+sinclude $(obj).depend -+ -+######################################################################### -diff --git a/board/acmesystems/netusg20/config.mk b/board/acmesystems/netusg20/config.mk -new file mode 100644 -index 0000000..ff2cfd1 ---- /dev/null -+++ b/board/acmesystems/netusg20/config.mk -@@ -0,0 +1 @@ -+TEXT_BASE = 0x23f00000 -diff --git a/board/acmesystems/netusg20/led.c b/board/acmesystems/netusg20/led.c -new file mode 100644 -index 0000000..1016b98 ---- /dev/null -+++ b/board/acmesystems/netusg20/led.c -@@ -0,0 +1,40 @@ -+/* -+ * (C) Copyright 2007-2008 -+ * Stelian Pop <stelian.pop@leadtechdesign.com> -+ * Lead Tech Design <www.leadtechdesign.com> -+ * -+ * See file CREDITS for list of people who contributed to this -+ * project. -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License as -+ * published by the Free Software Foundation; either version 2 of -+ * the License, or (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, -+ * MA 02111-1307 USA -+ */ -+ -+#include <common.h> -+#include <asm/arch/at91sam9260.h> -+#include <asm/arch/at91_pmc.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/io.h> -+ -+ -+void coloured_LED_init(void) -+{ -+ /* Enable clock */ -+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_PIOA); -+ -+ at91_set_gpio_output(CONFIG_RED_LED, 1); -+ -+ at91_set_gpio_value(CONFIG_RED_LED, 1); -+} -diff --git a/board/acmesystems/netusg20/netusg20.c b/board/acmesystems/netusg20/netusg20.c -new file mode 100644 -index 0000000..94b4d4c ---- /dev/null -+++ b/board/acmesystems/netusg20/netusg20.c -@@ -0,0 +1,152 @@ -+/* -+ * (C) Copyright 2007-2008 -+ * Stelian Pop <stelian.pop@leadtechdesign.com> -+ * Lead Tech Design <www.leadtechdesign.com> -+ * -+ * (C) Copyright 2010 -+ * Claudio Mignanti <c.mignanti@gmail.com> -+ * -+ * See file CREDITS for list of people who contributed to this -+ * project. -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License as -+ * published by the Free Software Foundation; either version 2 of -+ * the License, or (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, -+ * MA 02111-1307 USA -+ */ -+ -+#include <common.h> -+#include <asm/arch/at91sam9260.h> -+#include <asm/arch/at91sam9260_matrix.h> -+#include <asm/arch/at91sam9_smc.h> -+#include <asm/arch/at91_common.h> -+#include <asm/arch/at91_pmc.h> -+#include <asm/arch/at91_rstc.h> -+#include <asm/arch/gpio.h> -+#include <asm/arch/io.h> -+#include <asm/arch/hardware.h> -+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) -+#include <net.h> -+#endif -+#include <netdev.h> -+ -+DECLARE_GLOBAL_DATA_PTR; -+ -+/* ------------------------------------------------------------------------- */ -+/* -+ * Miscelaneous platform dependent initialisations -+ */ -+ -+#ifdef CONFIG_MACB -+static void at91sam9260ek_macb_hw_init(void) -+{ -+ unsigned long rstc; -+ -+ /* Enable clock */ -+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC); -+ -+ /* -+ * Disable pull-up on: -+ * RXDV (PA17) => PHY normal mode (not Test mode) -+ * ERX0 (PA14) => PHY ADDR0 -+ * ERX1 (PA15) => PHY ADDR1 -+ * ERX2 (PA25) => PHY ADDR2 -+ * ERX3 (PA26) => PHY ADDR3 -+ * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0 -+ * -+ * PHY has internal pull-down -+ */ -+ writel(pin_to_mask(AT91_PIN_PA14) | -+ pin_to_mask(AT91_PIN_PA15) | -+ pin_to_mask(AT91_PIN_PA17) | -+ pin_to_mask(AT91_PIN_PA25) | -+ pin_to_mask(AT91_PIN_PA26) | -+ pin_to_mask(AT91_PIN_PA28), -+ pin_to_controller(AT91_PIN_PA0) + PIO_PUDR); -+ -+ rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL; -+ -+ at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST); -+ -+ /* Wait for end hardware reset */ -+ while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL)); -+ -+ /* Restore NRST value */ -+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY | -+ (rstc) | -+ AT91_RSTC_URSTEN); -+ -+ /* Re-enable pull-up */ -+ writel(pin_to_mask(AT91_PIN_PA14) | -+ pin_to_mask(AT91_PIN_PA15) | -+ pin_to_mask(AT91_PIN_PA17) | -+ pin_to_mask(AT91_PIN_PA25) | -+ pin_to_mask(AT91_PIN_PA26) | -+ pin_to_mask(AT91_PIN_PA28), -+ pin_to_controller(AT91_PIN_PA0) + PIO_PUER); -+ -+ at91_macb_hw_init(); -+} -+#endif -+ -+int board_init(void) -+{ -+ /* Enable Ctrlc */ -+ console_init_f(); -+ -+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK; -+ -+ /* adress of boot parameters */ -+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; -+ -+ at91_serial_hw_init(); -+#ifdef CONFIG_HAS_DATAFLASH -+ at91_spi0_hw_init((1 << 0) | (1 << 1)); -+#endif -+#ifdef CONFIG_MACB -+ at91sam9260ek_macb_hw_init(); -+#endif -+ -+ return 0; -+} -+ -+int dram_init(void) -+{ -+ gd->bd->bi_dram[0].start = PHYS_SDRAM; -+ gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE; -+ return 0; -+} -+ -+#ifdef CONFIG_RESET_PHY_R -+void reset_phy(void) -+{ -+#ifdef CONFIG_MACB -+ /* -+ * Initialize ethernet HW addr prior to starting Linux, -+ * needed for nfsroot -+ */ -+ eth_init(gd->bd); -+#endif -+} -+#endif -+ -+int board_eth_init(bd_t *bis) -+{ -+ int rc = 0; -+#ifdef CONFIG_MACB -+ rc = macb_eth_initialize(0, (void *)AT91SAM9260_BASE_EMAC, 0x00); -+#endif -+ return rc; -+} -+ -+void show_boot_progress (int val){} -diff --git a/board/acmesystems/netusg20/partition.c b/board/acmesystems/netusg20/partition.c -new file mode 100644 -index 0000000..7d79e53 ---- /dev/null -+++ b/board/acmesystems/netusg20/partition.c -@@ -0,0 +1,39 @@ -+/* -+ * (C) Copyright 2008 -+ * Ulf Samuelsson <ulf@atmel.com> -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License as -+ * published by the Free Software Foundation; either version 2 of -+ * the License, or (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, -+ * MA 02111-1307 USA -+ * -+ */ -+#include <common.h> -+#include <config.h> -+#include <asm/hardware.h> -+#include <dataflash.h> -+ -+AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS]; -+ -+struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = { -+ {CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1, 1} -+}; -+ -+/*define the area offsets*/ -+dataflash_protect_t area_list[NB_DATAFLASH_AREA] = { -+ {0x00000000, 0x000041FF, FLAG_PROTECT_SET, 0, "Bootstrap"}, -+ {0x00004200, 0x000083FF, FLAG_PROTECT_CLEAR, 0, "Environment"}, -+ {0x00008400, 0x00041FFF, FLAG_PROTECT_SET, 0, "U-Boot"}, -+ {0x00042000, 0x00251FFF, FLAG_PROTECT_CLEAR, 0, "Kernel"}, -+ {0x00252000, 0xFFFFFFFF, FLAG_PROTECT_CLEAR, 0, "FS"}, -+}; -diff --git a/include/configs/netusg20.h b/include/configs/netusg20.h -new file mode 100644 -index 0000000..99b4f12 ---- /dev/null -+++ b/include/configs/netusg20.h -@@ -0,0 +1,181 @@ -+/* -+ * (C) Copyright 2007-2008 -+ * Stelian Pop <stelian.pop@leadtechdesign.com> -+ * Lead Tech Design <www.leadtechdesign.com> -+ * -+ * Configuation settings for the NetusG20 boards. -+ * -+ * See file CREDITS for list of people who contributed to this -+ * project. -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License as -+ * published by the Free Software Foundation; either version 2 of -+ * the License, or (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, -+ * MA 02111-1307 USA -+ */ -+ -+#ifndef __CONFIG_H -+#define __CONFIG_H -+ -+#define CONFIG_AT91_LEGACY -+ -+/* ARM asynchronous clock */ -+#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */ -+#define CONFIG_SYS_HZ 1000 -+ -+#define CONFIG_DISPLAY_CPUINFO -+ -+#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ -+#define CONFIG_AT91SAM9G20 1 /* It's an Atmel AT91SAM9G20 SoC*/ -+#define CONFIG_NETUSG20 1 -+ -+#define CONFIG_ARCH_CPU_INIT -+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ -+ -+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -+#define CONFIG_SETUP_MEMORY_TAGS 1 -+#define CONFIG_INITRD_TAG 1 -+ -+#define CONFIG_SKIP_LOWLEVEL_INIT -+#define CONFIG_SKIP_RELOCATE_UBOOT -+ -+/* -+ * Hardware drivers -+ */ -+#define CONFIG_AT91_GPIO 1 -+#define CONFIG_ATMEL_USART 1 -+#undef CONFIG_USART0 -+#undef CONFIG_USART1 -+#undef CONFIG_USART2 -+#define CONFIG_USART3 1 /* USART 3 is DBGU */ -+ -+/* LED */ -+#define CONFIG_AT91_LED -+#define CONFIG_RED_LED AT91_PIN_PA9 /* this is the power led */ -+#define CONFIG_GREEN_LED AT91_PIN_PA6 /* this is the user led */ -+ -+#define CONFIG_BOOTDELAY 3 -+ -+/* -+ * BOOTP options -+ */ -+#define CONFIG_BOOTP_BOOTFILESIZE 1 -+#define CONFIG_BOOTP_BOOTPATH 1 -+#define CONFIG_BOOTP_GATEWAY 1 -+#define CONFIG_BOOTP_HOSTNAME 1 -+ -+/* -+ * Command line configuration. -+ */ -+#include <config_cmd_default.h> -+#undef CONFIG_CMD_BDI -+#undef CONFIG_CMD_FPGA -+#undef CONFIG_CMD_IMI -+#undef CONFIG_CMD_IMLS -+#undef CONFIG_CMD_LOADS -+#undef CONFIG_CMD_SOURCE -+ -+#define CONFIG_CMD_PING 1 -+#define CONFIG_CMD_DHCP 1 -+#define CONFIG_CMD_USB 1 -+ -+/* SDRAM */ -+#define CONFIG_NR_DRAM_BANKS 1 -+#define PHYS_SDRAM 0x20000000 -+#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ -+ -+/* DataFlash */ -+#define CONFIG_ATMEL_DATAFLASH_SPI -+#define CONFIG_HAS_DATAFLASH 1 -+#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ) -+#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 -+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 0xD0000000 /* CS1 */ -+#define AT91_SPI_CLK 15000000 -+ -+#define DATAFLASH_TCSS (0x22 << 16) -+#define DATAFLASH_TCHS (0x1 << 24) -+ -+/* no NAND flash on this board*/ -+#define CONFIG_SYS_NO_FLASH -+ -+/* Ethernet */ -+#define CONFIG_MACB 1 -+#define CONFIG_RMII 1 -+#define CONFIG_NET_MULTI 1 -+#define CONFIG_NET_RETRY_COUNT 20 -+#define CONFIG_RESET_PHY_R 1 -+ -+/* MMC */ -+#define CONFIG_MMC -+#define CONFIG_CMD_MMC -+#define CONFIG_ATMEL_MCI -+#define CONFIG_CMD_AUTOSCRIPT -+#define CONFIG_CMD_IMI -+#define CONFIG_CMD_SOURCE -+ -+#define MMCI_BASE 0xFFFA8000 -+ -+/* USB */ -+#define CONFIG_USB_ATMEL -+#define CONFIG_USB_OHCI_NEW 1 -+#define CONFIG_DOS_PARTITION 1 -+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 -+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9260_UHP_BASE */ -+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" -+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 -+#define CONFIG_USB_STORAGE 1 -+ -+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ -+ -+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM -+#define CONFIG_SYS_MEMTEST_END 0x23e00000 -+ -+/* Filesystem */ -+#define CONFIG_CMD_FAT 1 -+#define CONFIG_CMD_EXT2 1 -+ -+/* bootstrap + u-boot + env + linux in dataflash on CS1 */ -+#define CONFIG_ENV_IS_IN_DATAFLASH 1 -+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + 0x8400) -+#define CONFIG_ENV_OFFSET 0x4200 -+#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + CONFIG_ENV_OFFSET) -+#define CONFIG_ENV_SIZE 0x4200 -+#define CONFIG_BOOTCOMMAND "mmc init; sleep 1; " \ -+ "ext2load mmc 0 0x20000000 uImage; " \ -+ "source 0x20000000" -+#define CONFIG_BOOTARGS "mem=64M console=ttyS0,115200 " \ -+ "root=/dev/mmcblk0p1 rootwait" -+ -+#define CONFIG_BAUDRATE 115200 -+#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } -+ -+#define CONFIG_SYS_PROMPT "U-Boot> " -+#define CONFIG_SYS_CBSIZE 256 -+#define CONFIG_SYS_MAXARGS 16 -+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -+#define CONFIG_SYS_LONGHELP 1 -+#define CONFIG_CMDLINE_EDITING 1 -+ -+/* -+ * Size of malloc() pool -+ */ -+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) -+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* 128 bytes for initial data */ -+ -+#define CONFIG_STACKSIZE (32*1024) /* regular stack */ -+ -+#ifdef CONFIG_USE_IRQ -+#error CONFIG_USE_IRQ not supported -+#endif -+ -+#endif --- -1.7.0.4 - - diff --git a/target/linux/at91/image/u-boot/patches/200-clock.patch b/target/linux/at91/image/u-boot/patches/200-clock.patch deleted file mode 100644 index fbfb6415e6..0000000000 --- a/target/linux/at91/image/u-boot/patches/200-clock.patch +++ /dev/null @@ -1,24 +0,0 @@ -The function get_mci_clk_rate is used inside atmel_mci driver -but never defined. Fix this typo. - -Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com> ---- - drivers/mmc/atmel_mci.c | 2 +- - 1 files changed, 1 insertions(+), 1 deletions(-) - -diff --git a/drivers/mmc/atmel_mci.c b/drivers/mmc/atmel_mci.c -index 3946ffe..628aac9 100644 ---- a/drivers/mmc/atmel_mci.c -+++ b/drivers/mmc/atmel_mci.c -@@ -67,7 +67,7 @@ static void mci_set_mode(unsigned long hz, unsigned long blklen) - unsigned long bus_hz; - unsigned long clkdiv; - -- bus_hz = get_mci_clk_rate(); -+ bus_hz = get_mck_clk_rate(); - clkdiv = (bus_hz / hz) / 2 - 1; - - pr_debug("mmc: setting clock %lu Hz, block size %lu\n", --- -1.7.0.4 - diff --git a/target/linux/at91/image/u-boot/ubclient/Makefile b/target/linux/at91/image/u-boot/ubclient/Makefile deleted file mode 100644 index f8ff67cd18..0000000000 --- a/target/linux/at91/image/u-boot/ubclient/Makefile +++ /dev/null @@ -1,15 +0,0 @@ -# - -all: ubpar - -crc32.c: - ln -s ../lib_generic/crc32.c ./ - -%.o: %.c - $(CC) -I ../include $(CFLAGS) $(EXTRA_FLAGS) -DLAN_IP=$(LAN_IP) -DLAN_SERVERIP=$(LAN_SERVERIP) -c -o $@ $^ - -ubpar: ubpar.o crc32.o - $(CC) -o $@ $^ - -clean: - rm -f *.o ubpar diff --git a/target/linux/at91/image/u-boot/ubclient/ubpar.c b/target/linux/at91/image/u-boot/ubclient/ubpar.c deleted file mode 100644 index edc5b2cdbd..0000000000 --- a/target/linux/at91/image/u-boot/ubclient/ubpar.c +++ /dev/null @@ -1,135 +0,0 @@ -/* - * ubparams.c - * - * Generate a u-boot parameter block with correct crc - * - * (C) 1007 Guthrie Consulting - * hamish@prodigi.ch - * - */ - -#include <stdio.h> -#include <stdlib.h> -#include <string.h> - -#ifndef __ASSEMBLY__ -#define __ASSEMBLY__ -#endif -#define __ASM_STUB_PROCESSOR_H__ -#include <config.h> -#undef __ASSEMBLY__ -#include <environment.h> - -#define XMK_STR(x) #x -#define MK_STR(x) XMK_STR(x) - -extern unsigned long crc32 (unsigned long, const unsigned char *, unsigned int); - -#if !defined(ENV_CRC) -#define ENV_CRC ~0 -#endif - -#ifdef LAN_IP - #warning LAN_IP -#else - #warning LAN_IP NOT DEFINED -#endif -#ifdef LAN_SERVERIP - #warning LAN_SERVERIP -#else - #warning LAN_SERVERIP NOT DEFINED -#endif - -static char *environment[] = { - "bootdelay=3\0" - "baudrate=115200\0" - "stdin=serial\0" - "stdout=serial\0" - "stderr=serial\0" - "fbargs=setenv bootargs root=/dev/mtdblock3 ro console=/dev/ttyS0,115200,mem=32M\0" - "rdba=setenv bootargs root=/dev/ram rw initrd=0x21200000,6000000 ramdisk_size=20000 console=/dev/ttyS0,115200,mem=32M\0" - "rdram=run rdba; tftp 21000000 uImage; tftp 21200000 root.squashfs; bootm 21000000\0" - "flash=run fbargs; bootm 0xc0042000\0" - "bootargs=setenv bootargs root=/dev/mtdblock3 ro console=/dev/ttyS0,115200,mem=32M\0" - "bootcmd=bootm 0xc0042000\0" - "ipaddr=" MK_STR(LAN_IP) "\0" - "serverip=" MK_STR(LAN_SERVERIP) "\0" - "\0" - }; - -int main(int argc, char *argv[]) { - env_t *envptr; - char *src, *srcptr; - char *dataptr; - FILE *params; - int argfail = 1; - char newmac[30]; - char newser[30]; - int paramlen = 0; - int progmac = 0; - int progser = 0; - - if (argc < 3) { - printf ("Invalid arguments\n"); - return 1; - } - - switch (argc) { - case 5: - if (strcmp(argv[3], "--serial") == 0) { - argfail = 0; - sprintf(newser, "serial#=%s", argv[4]); - progser = 1; - } - case 3: - if (strcmp(argv[1], "--mac") == 0) { - argfail = 0; - sprintf(newmac, "ethaddr=%s", argv[2]); - progmac = 1; - } - else - argfail = 1; - } - - if (argfail) { - printf("Invalid arguments\n"); - return 1; - } - - - src = srcptr = *environment; - envptr = (env_t *)malloc(CFG_ENV_SIZE); - dataptr = (char *)envptr + ENV_HEADER_SIZE; - - while(*srcptr) { - //printf("%d, %s\n", strlen(srcptr), srcptr); - paramlen += strlen(srcptr) + 1; - srcptr += strlen(srcptr) + 1; - } - - printf("Make u-boot params\n"); - printf("Params size is %d\n", CFG_ENV_SIZE); - - memset(envptr, 0, CFG_ENV_SIZE); - memcpy(dataptr, src, paramlen); - dataptr += paramlen; - - if (progmac) { - memcpy(dataptr, newmac, strlen(newmac)); - dataptr += strlen(newmac) + 1; - } - - if (progser) { - memcpy(dataptr, newser, strlen(newser)); - dataptr += strlen(newser) + 1; - } - - envptr->crc = crc32(0, envptr->data, ENV_SIZE); - - params = fopen("/dev/mtd1", "w"); - fwrite(envptr, CFG_ENV_SIZE, 1, params); - fclose(params); - - free(envptr); - return 0; -} |