aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux')
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/01_leds5
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/02_network7
-rw-r--r--target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata6
-rw-r--r--target/linux/ipq806x/base-files/lib/ipq806x.sh3
-rw-r--r--target/linux/ipq806x/config-4.418
-rw-r--r--target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts341
-rw-r--r--target/linux/ipq806x/image/Makefile25
-rw-r--r--target/linux/ipq806x/patches-4.4/800-devicetree.patch3
8 files changed, 400 insertions, 8 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index a7ace1f92e..53c2a80993 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -33,6 +33,11 @@ ea8500)
ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio"
ucidef_set_led_default "wps" "WPS" "ea8500:green:wps" "0"
;;
+nbg6817)
+ ucidef_set_led_wlan "wlan2g" "WLAN2g" "$board:amber:wifi" "phy1radio"
+ ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5" "phy0radio"
+ ucidef_set_led_netdev "wan" "WAN" "$board:white:internet" "eth1"
+ ;;
*)
;;
esac
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index b72045538a..a461033dfe 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -35,6 +35,13 @@ ea8500)
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
;;
+nbg6817)
+ hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
+ ucidef_add_switch "switch0" \
+ "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
+ ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
+ ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 1)"
+ ;;
*)
echo "Unsupported hardware. Network interfaces not intialized"
;;
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index c7977e6375..f95692a889 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -56,6 +56,9 @@ case "$FIRMWARE" in
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ath10kcal_extract "art" 4096 12064
;;
+ nbg6817)
+ ath10kcal_extract "0:ART" 4096 12064
+ ;;
r7500v2 |\
r7800)
ath10kcal_extract "art" 4096 12064
@@ -72,6 +75,9 @@ case "$FIRMWARE" in
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ath10kcal_extract "art" 20480 12064
;;
+ nbg6817)
+ ath10kcal_extract "0:ART" 20480 12064
+ ;;
r7500v2 |\
r7800)
ath10kcal_extract "art" 20480 12064
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index ea45381d91..1bd0e2bd94 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -26,6 +26,9 @@ ipq806x_board_detect() {
*"DB149")
name="db149"
;;
+ *"NBG6817")
+ name="nbg6817"
+ ;;
*"R7500")
name="r7500"
;;
diff --git a/target/linux/ipq806x/config-4.4 b/target/linux/ipq806x/config-4.4
index bc040497cb..1972e3675e 100644
--- a/target/linux/ipq806x/config-4.4
+++ b/target/linux/ipq806x/config-4.4
@@ -61,6 +61,7 @@ CONFIG_ARM_THUMB=y
CONFIG_ARM_UNWIND=y
CONFIG_ARM_VIRT_EXT=y
CONFIG_AT803X_PHY=y
+CONFIG_BLK_DEV_LOOP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_BOUNCE=y
@@ -197,11 +198,6 @@ CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZ4=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_HAVE_NET_DSA=y
@@ -262,6 +258,16 @@ CONFIG_MFD_SYSCON=y
CONFIG_MIGHT_HAVE_CACHE_L2X0=y
CONFIG_MIGHT_HAVE_PCI=y
CONFIG_MIGRATION=y
+CONFIG_MMC=y
+CONFIG_MMC_ARMMMCI=y
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_MINORS=16
+CONFIG_MMC_QCOM_DML=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_MSM=y
+# CONFIG_MMC_SDHCI_PCI is not set
+CONFIG_MMC_SDHCI_PLTFM=y
+# CONFIG_MMC_TIFM_SD is not set
CONFIG_MODULES_TREE_LOOKUP=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_MSM_GCC_8660=y
@@ -378,7 +384,6 @@ CONFIG_QCOM_SCM=y
CONFIG_QCOM_SCM_32=y
# CONFIG_QCOM_SMD is not set
CONFIG_QCOM_SMEM=y
-# CONFIG_QCOM_SPMI_TEMP_ALARM is not set
CONFIG_QCOM_WDT=y
CONFIG_RAS=y
CONFIG_RATIONAL=y
@@ -389,6 +394,7 @@ CONFIG_RD_GZIP=y
CONFIG_REGMAP=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_QCOM_RPM=y
# CONFIG_REGULATOR_QCOM_SPMI is not set
CONFIG_RESET_CONTROLLER=y
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
new file mode 100644
index 0000000000..cc56213fdb
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
@@ -0,0 +1,341 @@
+#include "qcom-ipq8065-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "ZyXEL NBG6817";
+ compatible = "zyxel,nbg6817", "qcom,ipq8065";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ mdio-gpio0 = &mdio0;
+ sdcc1 = &sdcc1;
+ };
+
+ chosen {
+ bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
+ pinctrl-names = "default";
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ clk {
+ pins = "gpio1";
+ input-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ tx {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+ input-disable;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <12>;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "ok";
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ flash: m25p80@0 {
+ compatible = "s25fl512s";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <51200000>;
+ reg = <0>;
+
+ linux,part-probe = "qcom-smem";
+ };
+ };
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
+ 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
+ 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
+ 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
+ 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
+ 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
+ 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
+ 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
+ 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
+ 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
+ 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
+ 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
+ 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
+ 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ qca,ar8327-initvals = <
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x0000c 0x80 /* PAD6_MODE */
+ >;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <0>;
+ qcom,rgmii_delay = <1>;
+ qcom,phy_mii_type = <0>;
+ qcom,emulation = <0>;
+ qcom,irq = <255>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ qcom,phy_mdio_addr = <0>; /* none */
+ qcom,poll_required = <0>; /* no polling */
+ qcom,rgmii_delay = <0>;
+ qcom,phy_mii_type = <1>;
+ qcom,emulation = <0>;
+ qcom,irq = <258>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ rpm@108000 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "default";
+ };
+
+ amba {
+ sdcc1: sdcc@12400000 {
+ status = "okay";
+ dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+ dma-names = "tx", "rx";
+ };
+ };
+
+
+
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ internet {
+ label = "nbg6817:white:internet";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+ };
+
+ power {
+ label = "nbg6817:white:power";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ wifi {
+ label = "nbg6817:amber:wifi";
+ gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi5g {
+ label = "nbg6817:amber:wifi5g";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ usb0_status {
+ gpio-export,name = "usb0";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb1_status {
+ gpio-export,name = "usb1";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+ };
+ usb1_power {
+ gpio-export,name = "usb1_power";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
+ };
+ usb2_power {
+ gpio-export,name = "usb2_power";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index b74f1a77c2..3bee923f93 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -90,6 +90,19 @@ define Device/TpSafeImage
endef
DEVICE_VARS += TPLINK_BOARD_NAME
+define Device/ZyXELImage
+ PROFILES += $$(DEVICE_NAME)
+ FILESYSTEMS := squashfs
+ KERNEL_SUFFIX := -uImage
+ KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$$${KERNEL_SIZE}
+ KERNEL_NAME := zImage
+ IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
+ IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@
+ IMAGE/sysupgrade.tar := sysupgrade-tar
+ IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE}
+ IMAGE/mmcblk0p4-kernel.bin := append-kernel
+endef
+
define Device/AP148
$(call Device/FitImage)
$(call Device/UbiFit)
@@ -202,6 +215,16 @@ define Device/R7800
DEVICE_PACKAGES := ath10k-firmware-qca9984
endef
-TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800
+define Device/NBG6817
+ DEVICE_DTS := qcom-ipq8065-nbg6817
+ KERNEL_SIZE := 4096k
+ BLOCKSIZE := 64k
+ BOARD_NAME := nbg6817
+ DEVICE_TITLE := ZyXEL NBG6817
+ DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs losetup
+ $(call Device/ZyXELImage)
+endef
+
+TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817
$(eval $(call BuildImage))
diff --git a/target/linux/ipq806x/patches-4.4/800-devicetree.patch b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
index 85f253429b..916e2efd72 100644
--- a/target/linux/ipq806x/patches-4.4/800-devicetree.patch
+++ b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
@@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -506,7 +506,13 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -506,7 +506,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
qcom-ipq8064-ap148.dtb \
@@ -22,6 +22,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
+ qcom-ipq8064-ea8500.dtb \
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-r7500v2.dtb \
++ qcom-ipq8065-nbg6817.dtb \
+ qcom-ipq8065-r7800.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \