diff options
Diffstat (limited to 'target/linux')
117 files changed, 0 insertions, 14251 deletions
diff --git a/target/linux/brcm63xx/config-3.6 b/target/linux/brcm63xx/config-3.6 deleted file mode 100644 index bccf2ae16f..0000000000 --- a/target/linux/brcm63xx/config-3.6 +++ /dev/null @@ -1,170 +0,0 @@ -CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y -CONFIG_ARCH_DISCARD_MEMBLOCK=y -CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y -CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_REQUIRE_GPIOLIB=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y -CONFIG_AUDIT=y -CONFIG_AUDIT_GENERIC=y -CONFIG_B53=y -CONFIG_B53_MMAP_DRIVER=y -CONFIG_B53_PHY_DRIVER=y -CONFIG_B53_PHY_FIXUP=y -CONFIG_B53_SPI_DRIVER=y -CONFIG_BCM63XX=y -CONFIG_BCM63XX_CPU_6328=y -CONFIG_BCM63XX_CPU_6338=y -CONFIG_BCM63XX_CPU_6345=y -CONFIG_BCM63XX_CPU_6348=y -CONFIG_BCM63XX_CPU_6358=y -CONFIG_BCM63XX_CPU_6362=y -CONFIG_BCM63XX_CPU_6368=y -CONFIG_BCM63XX_ENET=y -CONFIG_BCM63XX_PHY=y -CONFIG_BCM63XX_WDT=y -CONFIG_BOARD_BCM963XX=y -# CONFIG_BOARD_LIVEBOX is not set -CONFIG_CC_OPTIMIZE_FOR_SIZE=y -CONFIG_CEVT_R4K=y -CONFIG_CEVT_R4K_LIB=y -CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200" -CONFIG_CMDLINE_BOOL=y -# CONFIG_CMDLINE_OVERRIDE is not set -CONFIG_CPU_BIG_ENDIAN=y -CONFIG_CPU_HAS_PREFETCH=y -CONFIG_CPU_HAS_SYNC=y -CONFIG_CPU_MIPS32=y -CONFIG_CPU_MIPS32_R1=y -CONFIG_CPU_MIPSR1=y -CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_HIGHMEM=y -CONFIG_CRAMFS=y -CONFIG_CSRC_R4K=y -CONFIG_CSRC_R4K_LIB=y -CONFIG_DECOMPRESS_LZMA=y -CONFIG_DMA_NONCOHERENT=y -CONFIG_EARLY_PRINTK=y -CONFIG_ELF_CORE=y -CONFIG_FIRMWARE_IN_KERNEL=y -CONFIG_GENERIC_ATOMIC64=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y -CONFIG_GENERIC_CMOS_UPDATE=y -CONFIG_GENERIC_GPIO=y -CONFIG_GENERIC_IO=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GPIOLIB=y -CONFIG_GPIO_74X164=y -CONFIG_GPIO_SYSFS=y -# CONFIG_HAMRADIO is not set -CONFIG_HARDWARE_WATCHPOINTS=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAVE_ARCH_JUMP_LABEL=y -CONFIG_HAVE_ARCH_KGDB=y -CONFIG_HAVE_CLK=y -CONFIG_HAVE_C_RECORDMCOUNT=y -CONFIG_HAVE_DMA_API_DEBUG=y -CONFIG_HAVE_DMA_ATTRS=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y -CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y -CONFIG_HAVE_FUNCTION_TRACER=y -CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y -CONFIG_HAVE_GENERIC_DMA_COHERENT=y -CONFIG_HAVE_GENERIC_HARDIRQS=y -CONFIG_HAVE_IDE=y -CONFIG_HAVE_IRQ_WORK=y -CONFIG_HAVE_MEMBLOCK=y -CONFIG_HAVE_MEMBLOCK_NODE_MAP=y -CONFIG_HAVE_OPROFILE=y -CONFIG_HAVE_PERF_EVENTS=y -CONFIG_HW_HAS_PCI=y -CONFIG_HW_RANDOM=y -CONFIG_HW_RANDOM_BCM63XX=y -CONFIG_HZ=250 -# CONFIG_HZ_100 is not set -CONFIG_HZ_250=y -CONFIG_IMAGE_CMDLINE_HACK=y -CONFIG_INITRAMFS_SOURCE="" -CONFIG_IP_PIMSM_V1=y -CONFIG_IP_PIMSM_V2=y -CONFIG_IRQ_CPU=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_KEXEC=y -CONFIG_LEDS_GPIO=y -CONFIG_M25PXX_USE_FAST_READ=y -CONFIG_MDIO_BOARDINFO=y -CONFIG_MIPS=y -CONFIG_MIPS_L1_CACHE_SHIFT=5 -# CONFIG_MIPS_MACHINE is not set -CONFIG_MIPS_MT_DISABLED=y -CONFIG_MODULE_FORCE_LOAD=y -CONFIG_MODULE_FORCE_UNLOAD=y -CONFIG_MTD_BCM63XX_PARTS=y -CONFIG_MTD_CFI_ADV_OPTIONS=y -CONFIG_MTD_CFI_BE_BYTE_SWAP=y -# CONFIG_MTD_CFI_GEOMETRY is not set -# CONFIG_MTD_CFI_NOSWAP is not set -CONFIG_MTD_CFI_STAA=y -CONFIG_MTD_CMDLINE_PARTS=y -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -CONFIG_MTD_JEDECPROBE=y -CONFIG_MTD_M25P80=y -CONFIG_MTD_PHYSMAP=y -CONFIG_MTD_REDBOOT_PARTS=y -CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_PER_CPU_KM=y -CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_PCI=y -# CONFIG_PCIEAER is not set -CONFIG_PCIEPORTBUS=y -CONFIG_PCI_DOMAINS=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PHYLIB=y -CONFIG_POSIX_MQUEUE=y -CONFIG_POSIX_MQUEUE_SYSCTL=y -# CONFIG_PREEMPT_RCU is not set -CONFIG_RELAY=y -CONFIG_RTL8366_SMI=y -CONFIG_RTL8367_PHY=y -# CONFIG_SCSI_DMA is not set -# CONFIG_SERIAL_8250 is not set -CONFIG_SERIAL_BCM63XX=y -CONFIG_SERIAL_BCM63XX_CONSOLE=y -CONFIG_SPI=y -CONFIG_SPI_BCM63XX=y -CONFIG_SPI_BCM63XX_HSSPI=y -CONFIG_SPI_BITBANG=y -CONFIG_SPI_GPIO=y -CONFIG_SPI_MASTER=y -CONFIG_SQUASHFS_EMBEDDED=y -CONFIG_SSB=y -CONFIG_SSB_B43_PCI_BRIDGE=y -CONFIG_SSB_BLOCKIO=y -# CONFIG_SSB_DRIVER_MIPS is not set -CONFIG_SSB_DRIVER_PCICORE=y -CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y -CONFIG_SSB_PCIHOST=y -CONFIG_SSB_PCIHOST_POSSIBLE=y -CONFIG_SSB_SPROM=y -CONFIG_SWAP_IO_SPACE=y -CONFIG_SWCONFIG=y -CONFIG_SYS_HAS_CPU_MIPS32_R1=y -CONFIG_SYS_HAS_EARLY_PRINTK=y -CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y -CONFIG_SYS_SUPPORTS_ARBIT_HZ=y -CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y -CONFIG_USB_ARCH_HAS_XHCI=y -# CONFIG_USB_HCD_SSB is not set -CONFIG_USB_SUPPORT=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_WATCHDOG_NOWAYOUT=y -CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/brcm63xx/patches-3.6/030-MIPS-BCM63XX-Fix-BCM6345-clock-bits.patch b/target/linux/brcm63xx/patches-3.6/030-MIPS-BCM63XX-Fix-BCM6345-clock-bits.patch deleted file mode 100644 index b33a8450b7..0000000000 --- a/target/linux/brcm63xx/patches-3.6/030-MIPS-BCM63XX-Fix-BCM6345-clock-bits.patch +++ /dev/null @@ -1,34 +0,0 @@ -[PATCH] MIPS: BCM63XX: fix BCM6345 clock bits shifting - -BCM6345 has an intermediate 16-bits wide test control register between the -peripheral identifier function, and its clock control register is only 16-bits -wide contrary to other platforms where it is 32-bits wide. By shifting all -clocks bits by 16-bits to the left we ensure they get written to the proper -clock control register, without adding specific BCM6345 handling in the clock -code. - -Signed-off-by: Florian Fainelli <florian@openwrt.org> ---- ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -53,13 +53,13 @@ - CKCTL_6338_SAR_EN | \ - CKCTL_6338_SPI_EN) - --#define CKCTL_6345_CPU_EN (1 << 0) --#define CKCTL_6345_BUS_EN (1 << 1) --#define CKCTL_6345_EBI_EN (1 << 2) --#define CKCTL_6345_UART_EN (1 << 3) --#define CKCTL_6345_ADSLPHY_EN (1 << 4) --#define CKCTL_6345_ENET_EN (1 << 7) --#define CKCTL_6345_USBH_EN (1 << 8) -+#define CKCTL_6345_CPU_EN (1 << 16) -+#define CKCTL_6345_BUS_EN (1 << 17) -+#define CKCTL_6345_EBI_EN (1 << 18) -+#define CKCTL_6345_UART_EN (1 << 19) -+#define CKCTL_6345_ADSLPHY_EN (1 << 20) -+#define CKCTL_6345_ENET_EN (1 << 23) -+#define CKCTL_6345_USBH_EN (1 << 24) - - #define CKCTL_6345_ALL_SAFE_EN (CKCTL_6345_ENET_EN | \ - CKCTL_6345_USBH_EN | \ diff --git a/target/linux/brcm63xx/patches-3.6/040-MIPS-BCM63XX-Fix-USB-IRQ-definitions-for-6328.patch b/target/linux/brcm63xx/patches-3.6/040-MIPS-BCM63XX-Fix-USB-IRQ-definitions-for-6328.patch deleted file mode 100644 index c9d0421a28..0000000000 --- a/target/linux/brcm63xx/patches-3.6/040-MIPS-BCM63XX-Fix-USB-IRQ-definitions-for-6328.patch +++ /dev/null @@ -1,26 +0,0 @@ -From 960e1ef3c5b2d69a4a5a6984b6408d65221dd86c Mon Sep 17 00:00:00 2001 -From: Kevin Cernekee <cernekee@gmail.com> -Date: Sat, 23 Jun 2012 04:14:55 +0000 -Subject: [PATCH 06/81] MIPS: BCM63XX: Fix USB IRQ definitions for 6328 - -OHCI/EHCI are in the high (second) word. Not currently used by any -driver. - -Signed-off-by: Kevin Cernekee <cernekee@gmail.com> ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -602,8 +602,8 @@ enum bcm63xx_irq { - #define BCM_6328_ENET0_IRQ 0 - #define BCM_6328_ENET1_IRQ 0 - #define BCM_6328_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12) --#define BCM_6328_OHCI0_IRQ (IRQ_INTERNAL_BASE + 9) --#define BCM_6328_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10) -+#define BCM_6328_OHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 9) -+#define BCM_6328_EHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 10) - #define BCM_6328_PCMCIA_IRQ 0 - #define BCM_6328_ENET0_RXDMA_IRQ 0 - #define BCM_6328_ENET0_TXDMA_IRQ 0 diff --git a/target/linux/brcm63xx/patches-3.6/041-BCM63XX-Add-register-definitions-for-USBD-depen.patch b/target/linux/brcm63xx/patches-3.6/041-BCM63XX-Add-register-definitions-for-USBD-depen.patch deleted file mode 100644 index c2130a563e..0000000000 --- a/target/linux/brcm63xx/patches-3.6/041-BCM63XX-Add-register-definitions-for-USBD-depen.patch +++ /dev/null @@ -1,62 +0,0 @@ -From 21bb8141c205ae48d331787debb6b272add90ac7 Mon Sep 17 00:00:00 2001 -From: Kevin Cernekee <cernekee@gmail.com> -Date: Sat, 23 Jun 2012 04:14:54 +0000 -Subject: [PATCH 05/81] MIPS: BCM63XX: Add register definitions for USBD - dependencies - -The USB 2.0 device depends on some functionality in other blocks, such -as GPIO and USBH. Add those register definitions here. - -Signed-off-by: Kevin Cernekee <cernekee@gmail.com> ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 6 +++--- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 8 ++++++++ - 2 files changed, 11 insertions(+), 3 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -184,9 +184,9 @@ enum bcm63xx_regs_set { - #define BCM_6328_SPI_BASE (0xdeadbeef) - #define BCM_6328_UDC0_BASE (0xdeadbeef) - #define BCM_6328_USBDMA_BASE (0xdeadbeef) --#define BCM_6328_OHCI0_BASE (0xdeadbeef) -+#define BCM_6328_OHCI0_BASE (0xb0002600) - #define BCM_6328_OHCI_PRIV_BASE (0xdeadbeef) --#define BCM_6328_USBH_PRIV_BASE (0xdeadbeef) -+#define BCM_6328_USBH_PRIV_BASE (0xb0002700) - #define BCM_6328_MPI_BASE (0xdeadbeef) - #define BCM_6328_PCMCIA_BASE (0xdeadbeef) - #define BCM_6328_PCIE_BASE (0xb0e40000) -@@ -199,7 +199,7 @@ enum bcm63xx_regs_set { - #define BCM_6328_ENETDMAC_BASE (0xb000da00) - #define BCM_6328_ENETDMAS_BASE (0xb000dc00) - #define BCM_6328_ENETSW_BASE (0xb0e00000) --#define BCM_6328_EHCI0_BASE (0x10002500) -+#define BCM_6328_EHCI0_BASE (0xb0002500) - #define BCM_6328_SDRAM_BASE (0xdeadbeef) - #define BCM_6328_MEMC_BASE (0xdeadbeef) - #define BCM_6328_DDR_BASE (0xb0003000) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -543,6 +543,12 @@ - #define GPIO_MODE_6368_SPI_SSN5 (1 << 31) - - -+#define GPIO_PINMUX_OTHR_REG 0x24 -+#define GPIO_PINMUX_OTHR_6328_USB_SHIFT 12 -+#define GPIO_PINMUX_OTHR_6328_USB_MASK (3 << GPIO_PINMUX_OTHR_6328_USB_SHIFT) -+#define GPIO_PINMUX_OTHR_6328_USB_HOST (1 << GPIO_PINMUX_OTHR_6328_USB_SHIFT) -+#define GPIO_PINMUX_OTHR_6328_USB_DEV (2 << GPIO_PINMUX_OTHR_6328_USB_SHIFT) -+ - #define GPIO_BASEMODE_6368_REG 0x38 - #define GPIO_BASEMODE_6368_UART2 0x1 - #define GPIO_BASEMODE_6368_GPIO 0x0 -@@ -770,6 +776,8 @@ - #define USBH_PRIV_SWAP_6358_REG 0x0 - #define USBH_PRIV_SWAP_6368_REG 0x1c - -+#define USBH_PRIV_SWAP_USBD_SHIFT 6 -+#define USBH_PRIV_SWAP_USBD_MASK (1 << USBH_PRIV_SWAP_USBD_SHIFT) - #define USBH_PRIV_SWAP_EHCI_ENDN_SHIFT 4 - #define USBH_PRIV_SWAP_EHCI_ENDN_MASK (1 << USBH_PRIV_SWAP_EHCI_ENDN_SHIFT) - #define USBH_PRIV_SWAP_EHCI_DATA_SHIFT 3 diff --git a/target/linux/brcm63xx/patches-3.6/101-MTD-bcm63xxpart-remove-unused-variable.patch b/target/linux/brcm63xx/patches-3.6/101-MTD-bcm63xxpart-remove-unused-variable.patch deleted file mode 100644 index 470f966635..0000000000 --- a/target/linux/brcm63xx/patches-3.6/101-MTD-bcm63xxpart-remove-unused-variable.patch +++ /dev/null @@ -1,41 +0,0 @@ -From 2962bbe9cc807549c0705551c5b7be47e34e3fac Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Mon, 30 Apr 2012 09:32:56 +0200 -Subject: [PATCH 20/79] MTD: bcm63xxpart: remove unused variable - -namelen is never used, so drop it. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/mtd/bcm63xxpart.c | 11 +++-------- - 1 file changed, 3 insertions(+), 8 deletions(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -79,7 +79,6 @@ static int bcm63xx_parse_cfe_partitions( - unsigned int rootfsaddr, kerneladdr, spareaddr; - unsigned int rootfslen, kernellen, sparelen, totallen; - unsigned int cfelen, nvramlen; -- int namelen = 0; - int i; - u32 computed_crc; - bool rootfs_first = false; -@@ -143,15 +142,11 @@ static int bcm63xx_parse_cfe_partitions( - } - - /* Determine number of partitions */ -- namelen = 8; -- if (rootfslen > 0) { -+ if (rootfslen > 0) - nrparts++; -- namelen += 6; -- } -- if (kernellen > 0) { -+ -+ if (kernellen > 0) - nrparts++; -- namelen += 6; -- } - - /* Ask kernel for more memory */ - parts = kzalloc(sizeof(*parts) * nrparts + 10 * nrparts, GFP_KERNEL); diff --git a/target/linux/brcm63xx/patches-3.6/102-MTD-bcm63xxpart-merge-sparelen-calculation.patch b/target/linux/brcm63xx/patches-3.6/102-MTD-bcm63xxpart-merge-sparelen-calculation.patch deleted file mode 100644 index da24b1b858..0000000000 --- a/target/linux/brcm63xx/patches-3.6/102-MTD-bcm63xxpart-merge-sparelen-calculation.patch +++ /dev/null @@ -1,33 +0,0 @@ -From fd2ab39f22af4176eb3d23acbc4d1218cf835065 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 8 May 2012 09:47:32 +0200 -Subject: [PATCH 21/79] MTD: bcm63xxpart: merge sparelen calculation - -The length of the spare part is calculated the same way in both branches -so move to a common place. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/mtd/bcm63xxpart.c | 3 +-- - 1 file changed, 1 insertion(+), 2 deletions(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -120,7 +120,6 @@ static int bcm63xx_parse_cfe_partitions( - kerneladdr = kerneladdr - BCM63XX_EXTENDED_SIZE; - rootfsaddr = rootfsaddr - BCM63XX_EXTENDED_SIZE; - spareaddr = roundup(totallen, master->erasesize) + cfelen; -- sparelen = master->size - spareaddr - nvramlen; - - if (rootfsaddr < kerneladdr) { - /* default Broadcom layout */ -@@ -138,8 +137,8 @@ static int bcm63xx_parse_cfe_partitions( - rootfslen = 0; - rootfsaddr = 0; - spareaddr = cfelen; -- sparelen = master->size - cfelen - nvramlen; - } -+ sparelen = master->size - spareaddr - nvramlen; - - /* Determine number of partitions */ - if (rootfslen > 0) diff --git a/target/linux/brcm63xx/patches-3.6/103-MTD-bcm63xxpart-make-fixed-part-length-calculation-m.patch b/target/linux/brcm63xx/patches-3.6/103-MTD-bcm63xxpart-make-fixed-part-length-calculation-m.patch deleted file mode 100644 index ca0cddde94..0000000000 --- a/target/linux/brcm63xx/patches-3.6/103-MTD-bcm63xxpart-make-fixed-part-length-calculation-m.patch +++ /dev/null @@ -1,49 +0,0 @@ -From 465f1b3ff24dbf3bec43dce344a7bc2640e05ffc Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 8 May 2012 09:53:07 +0200 -Subject: [PATCH 22/79] MTD: bcm63xxpart: make fixed part length calculation - more generic - -The CFE does not use 4K sectors even if the flash supports it, so -for the fixed partitions like CFE itself or NVRAM the erase block -size is always 64k or bigger. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/mtd/bcm63xxpart.c | 11 +++++++---- - 1 file changed, 7 insertions(+), 4 deletions(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -37,8 +37,7 @@ - - #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */ - --#define BCM63XX_MIN_CFE_SIZE 0x10000 /* always at least 64KiB */ --#define BCM63XX_MIN_NVRAM_SIZE 0x10000 /* always at least 64KiB */ -+#define BCM63XX_CFE_BLOCK_SIZE 0x10000 /* always at least 64KiB */ - - #define BCM63XX_CFE_MAGIC_OFFSET 0x4e0 - -@@ -79,6 +78,7 @@ static int bcm63xx_parse_cfe_partitions( - unsigned int rootfsaddr, kerneladdr, spareaddr; - unsigned int rootfslen, kernellen, sparelen, totallen; - unsigned int cfelen, nvramlen; -+ unsigned int cfe_erasesize; - int i; - u32 computed_crc; - bool rootfs_first = false; -@@ -86,8 +86,11 @@ static int bcm63xx_parse_cfe_partitions( - if (bcm63xx_detect_cfe(master)) - return -EINVAL; - -- cfelen = max_t(uint32_t, master->erasesize, BCM63XX_MIN_CFE_SIZE); -- nvramlen = max_t(uint32_t, master->erasesize, BCM63XX_MIN_NVRAM_SIZE); -+ cfe_erasesize = max_t(uint32_t, master->erasesize, -+ BCM63XX_CFE_BLOCK_SIZE); -+ -+ cfelen = cfe_erasesize; -+ nvramlen = cfe_erasesize; - - /* Allocate memory for buffer */ - buf = vmalloc(sizeof(struct bcm_tag)); diff --git a/target/linux/brcm63xx/patches-3.6/104-MTD-bcm63xxpart-move-the-last-curpart-to-its-correct.patch b/target/linux/brcm63xx/patches-3.6/104-MTD-bcm63xxpart-move-the-last-curpart-to-its-correct.patch deleted file mode 100644 index 8e05803ff0..0000000000 --- a/target/linux/brcm63xx/patches-3.6/104-MTD-bcm63xxpart-move-the-last-curpart-to-its-correct.patch +++ /dev/null @@ -1,26 +0,0 @@ -From d5173b2c806f4039679b001f1b55a3c245afdf68 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 8 May 2012 10:02:13 +0200 -Subject: [PATCH 23/79] MTD: bcm63xxpart: move the last curpart++ to its - correct place - -The line belongs above the comment, not below it. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/mtd/bcm63xxpart.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -190,9 +190,9 @@ static int bcm63xx_parse_cfe_partitions( - parts[curpart].name = "nvram"; - parts[curpart].offset = master->size - nvramlen; - parts[curpart].size = nvramlen; -+ curpart++; - - /* Global partition "linux" to make easy firmware upgrade */ -- curpart++; - parts[curpart].name = "linux"; - parts[curpart].offset = cfelen; - parts[curpart].size = master->size - cfelen - nvramlen; diff --git a/target/linux/brcm63xx/patches-3.6/105-MTD-bcm63xxpart-use-correct-printk-format-for-partit.patch b/target/linux/brcm63xx/patches-3.6/105-MTD-bcm63xxpart-use-correct-printk-format-for-partit.patch deleted file mode 100644 index 60396abae8..0000000000 --- a/target/linux/brcm63xx/patches-3.6/105-MTD-bcm63xxpart-use-correct-printk-format-for-partit.patch +++ /dev/null @@ -1,27 +0,0 @@ -From 55aa355612ce55dc1943f116ea49e795a098b60c Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 8 May 2012 10:03:27 +0200 -Subject: [PATCH 24/79] MTD: bcm63xxpart: use correct printk format for - partitions - -Use ll to be able to remove the casts. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/mtd/bcm63xxpart.c | 5 ++--- - 1 file changed, 2 insertions(+), 3 deletions(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -198,9 +198,8 @@ static int bcm63xx_parse_cfe_partitions( - parts[curpart].size = master->size - cfelen - nvramlen; - - for (i = 0; i < nrparts; i++) -- pr_info("Partition %d is %s offset %lx and length %lx\n", i, -- parts[i].name, (long unsigned int)(parts[i].offset), -- (long unsigned int)(parts[i].size)); -+ pr_info("Partition %d is %s offset %llx and length %llx\n", i, -+ parts[i].name, parts[i].offset, parts[i].size); - - pr_info("Spare partition is offset %x and length %x\n", spareaddr, - sparelen); diff --git a/target/linux/brcm63xx/patches-3.6/106-bcm63xx-fix-transfer-bits_per_words-check.patch b/target/linux/brcm63xx/patches-3.6/106-bcm63xx-fix-transfer-bits_per_words-check.patch deleted file mode 100644 index 37d9d49d6f..0000000000 --- a/target/linux/brcm63xx/patches-3.6/106-bcm63xx-fix-transfer-bits_per_words-check.patch +++ /dev/null @@ -1,29 +0,0 @@ -From fbef4dff80be6254e36ab5b9c655d248a3991ded Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sat, 24 Nov 2012 12:08:22 +0100 -Subject: [PATCH 3.7] spi/bcm63xx: fix transfer bits_per_words check - -Transfers often do not have bits_per_words set, so use the spi device's -bits_per_words in this case. - -This fixes the driver rejecting valid transfers e.g. generated by -spi_write() or spi_read(). - -Cc: stable@vger.kernel.org -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/spi/spi-bcm63xx.c | 3 ++- - 1 file changed, 2 insertions(+), 1 deletion(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -103,7 +103,8 @@ static int bcm63xx_spi_check_transfer(st - { - u8 bits_per_word; - -- bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word; -+ bits_per_word = (t && t->bits_per_word) ? -+ t->bits_per_word : spi->bits_per_word; - if (bits_per_word != 8) { - dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", - __func__, bits_per_word); diff --git a/target/linux/brcm63xx/patches-3.6/107-spi-bcm63xx-fix-multi-transfer-messages.patch b/target/linux/brcm63xx/patches-3.6/107-spi-bcm63xx-fix-multi-transfer-messages.patch deleted file mode 100644 index 2da5044492..0000000000 --- a/target/linux/brcm63xx/patches-3.6/107-spi-bcm63xx-fix-multi-transfer-messages.patch +++ /dev/null @@ -1,279 +0,0 @@ -From 0f2ae1e1282ff64f74a5e36f7da874f94911225e Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Wed, 14 Nov 2012 22:22:33 +0100 -Subject: [PATCH] spi/bcm63xx: fix multi transfer messages - -The BCM63XX SPI controller does not support keeping CS asserted after -sending its buffer. This breaks common usages like spi_write_then_read, -where it is expected to be kept active during the whole transfers. - -Work around this by combining the transfers into one if the buffer -allows. For spi_write_then_read, use the prepend byte feature to write -to "prepend" the write if it is less than 15 bytes, allowing the whole -fifo size for the read. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- -Tested on a SPI conntected switch which required keeping CS active between -the register read command and reading the register contents. - -Based on Mark's spi/next. - -Not sure if this is stable material, as it's quite invasive. - - drivers/spi/spi-bcm63xx.c | 172 ++++++++++++++++++++++++++++++--------------- - 1 file changed, 117 insertions(+), 55 deletions(-) - ---- a/drivers/spi/spi-bcm63xx.c -+++ b/drivers/spi/spi-bcm63xx.c -@@ -38,6 +38,8 @@ - #define PFX KBUILD_MODNAME - #define DRV_VER "0.1.2" - -+#define BCM63XX_SPI_MAX_PREPEND 15 -+ - struct bcm63xx_spi { - struct completion done; - -@@ -50,16 +52,10 @@ struct bcm63xx_spi { - unsigned int msg_type_shift; - unsigned int msg_ctl_width; - -- /* Data buffers */ -- const unsigned char *tx_ptr; -- unsigned char *rx_ptr; -- - /* data iomem */ - u8 __iomem *tx_io; - const u8 __iomem *rx_io; - -- int remaining_bytes; -- - struct clk *clk; - struct platform_device *pdev; - }; -@@ -184,50 +180,60 @@ static int bcm63xx_spi_setup(struct spi_ - return 0; - } - --/* Fill the TX FIFO with as many bytes as possible */ --static void bcm63xx_spi_fill_tx_fifo(struct bcm63xx_spi *bs) --{ -- u8 size; -- -- /* Fill the Tx FIFO with as many bytes as possible */ -- size = bs->remaining_bytes < bs->fifo_size ? bs->remaining_bytes : -- bs->fifo_size; -- memcpy_toio(bs->tx_io, bs->tx_ptr, size); -- bs->remaining_bytes -= size; --} -- - static unsigned int bcm63xx_txrx_bufs(struct spi_device *spi, -- struct spi_transfer *t) -+ struct spi_transfer *first, -+ unsigned int n_transfers) - { - struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master); - u16 msg_ctl; - u16 cmd; -+ unsigned int i, timeout, total_len = 0, prepend_len = 0, len = 0; -+ struct spi_transfer *t = first; -+ u8 rx_tail; -+ bool do_rx = false; -+ bool do_tx = false; - - /* Disable the CMD_DONE interrupt */ - bcm_spi_writeb(bs, 0, SPI_INT_MASK); - -- dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n", -- t->tx_buf, t->rx_buf, t->len); -+ if (n_transfers > 1 && t->tx_buf && t->len <= BCM63XX_SPI_MAX_PREPEND) -+ prepend_len = t->len; -+ -+ /* prepare the buffer */ -+ for (i = 0; i < n_transfers; i++) { -+ if (t->tx_buf) { -+ do_tx = true; -+ memcpy_toio(bs->tx_io + total_len, t->tx_buf, t->len); -+ -+ /* don't prepend more than one tx */ -+ if (t != first) -+ prepend_len = 0; -+ } -+ -+ if (t->rx_buf) { -+ do_rx = true; -+ if (t == first) -+ prepend_len = 0; -+ } - -- /* Transmitter is inhibited */ -- bs->tx_ptr = t->tx_buf; -- bs->rx_ptr = t->rx_buf; -- -- if (t->tx_buf) { -- bs->remaining_bytes = t->len; -- bcm63xx_spi_fill_tx_fifo(bs); -+ total_len += t->len; -+ -+ t = list_entry(t->transfer_list.next, struct spi_transfer, -+ transfer_list); - } - -+ len = total_len - prepend_len; -+ - init_completion(&bs->done); - - /* Fill in the Message control register */ -- msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT); -+ msg_ctl = (len << SPI_BYTE_CNT_SHIFT); - -- if (t->rx_buf && t->tx_buf) -+ if (do_rx && do_tx && prepend_len == 0) - msg_ctl |= (SPI_FD_RW << bs->msg_type_shift); -- else if (t->rx_buf) -+ else if (do_rx) - msg_ctl |= (SPI_HD_R << bs->msg_type_shift); -- else if (t->tx_buf) -+ else if (do_tx) - msg_ctl |= (SPI_HD_W << bs->msg_type_shift); - - switch (bs->msg_ctl_width) { -@@ -241,14 +247,41 @@ static unsigned int bcm63xx_txrx_bufs(st - - /* Issue the transfer */ - cmd = SPI_CMD_START_IMMEDIATE; -- cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT); -+ cmd |= (prepend_len << SPI_CMD_PREPEND_BYTE_CNT_SHIFT); - cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT); - bcm_spi_writew(bs, cmd, SPI_CMD); - - /* Enable the CMD_DONE interrupt */ - bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK); - -- return t->len - bs->remaining_bytes; -+ timeout = wait_for_completion_timeout(&bs->done, HZ); -+ if (!timeout) -+ return -ETIMEDOUT; -+ -+ /* read out all data */ -+ rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL); -+ -+ if (do_rx && rx_tail != len) -+ return -EINVAL; -+ -+ if (!rx_tail) -+ return total_len; -+ -+ len = 0; -+ t = first; -+ /* Read out all the data */ -+ for (i = 0; i < n_transfers; i++) { -+ if (t->rx_buf) -+ memcpy_fromio(t->rx_buf, bs->rx_io + len, t->len); -+ -+ if (t != first || prepend_len == 0) -+ len += t->len; -+ -+ t = list_entry(t->transfer_list.next, struct spi_transfer, -+ transfer_list); -+ } -+ -+ return total_len; - } - - static int bcm63xx_spi_prepare_transfer(struct spi_master *master) -@@ -273,42 +306,71 @@ static int bcm63xx_spi_transfer_one(stru - struct spi_message *m) - { - struct bcm63xx_spi *bs = spi_master_get_devdata(master); -- struct spi_transfer *t; -+ struct spi_transfer *t, *first = NULL; - struct spi_device *spi = m->spi; - int status = 0; -- unsigned int timeout = 0; -+ unsigned int n_transfers = 0, total_len = 0; -+ bool can_use_prepend = false; - -+ /* -+ * This SPI controller does not support keeping CS active after a -+ * transfer, so we need to combine the transfers into one until we may -+ * deassert CS. -+ */ - list_for_each_entry(t, &m->transfers, transfer_list) { -- unsigned int len = t->len; -- u8 rx_tail; -- - status = bcm63xx_spi_check_transfer(spi, t); - if (status < 0) - goto exit; - -- /* configure adapter for a new transfer */ -- bcm63xx_spi_setup_transfer(spi, t); -+ if (!first) -+ first = t; - -- while (len) { -- /* send the data */ -- len -= bcm63xx_txrx_bufs(spi, t); -- -- timeout = wait_for_completion_timeout(&bs->done, HZ); -- if (!timeout) { -- status = -ETIMEDOUT; -- goto exit; -- } -+ n_transfers++; -+ total_len += t->len; -+ -+ if (n_transfers == 2 && !first->rx_buf && !t->tx_buf && -+ first->len <= BCM63XX_SPI_MAX_PREPEND) -+ can_use_prepend = true; -+ else if (can_use_prepend && t->tx_buf) -+ can_use_prepend = false; -+ -+ if ((can_use_prepend && -+ total_len > (bs->fifo_size + BCM63XX_SPI_MAX_PREPEND)) || -+ (!can_use_prepend && total_len > bs->fifo_size)) { -+ status = -EINVAL; -+ goto exit; -+ } - -- /* read out all data */ -- rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL); -+ /* all transfers have to be made at the same speed */ -+ if (t->speed_hz != first->speed_hz) { -+ status = -EINVAL; -+ goto exit; -+ } - -- /* Read out all the data */ -- if (rx_tail) -- memcpy_fromio(bs->rx_ptr, bs->rx_io, rx_tail); -+ /* CS will be deasserted directly after the transfer */ -+ if (t->delay_usecs) { -+ status = -EINVAL; -+ goto exit; - } - -- m->actual_length += t->len; -+ if (t->cs_change || -+ list_is_last(&t->transfer_list, &m->transfers)) { -+ /* configure adapter for a new transfer */ -+ bcm63xx_spi_setup_transfer(spi, first); -+ -+ status = bcm63xx_txrx_bufs(spi, first, n_transfers); -+ if (status < 0) -+ goto exit; -+ -+ m->actual_length += status; -+ first = NULL; -+ status = 0; -+ n_transfers = 0; -+ total_len = 0; -+ can_use_prepend = false; -+ } - } -+ - exit: - m->status = status; - spi_finalize_current_message(master); diff --git a/target/linux/brcm63xx/patches-3.6/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch b/target/linux/brcm63xx/patches-3.6/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch deleted file mode 100644 index 00dc9c90ee..0000000000 --- a/target/linux/brcm63xx/patches-3.6/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch +++ /dev/null @@ -1,38 +0,0 @@ -From 3f650fc30aa0badf9d02842ce396cea3eef2eeaa Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Fri, 1 Jul 2011 23:16:47 +0200 -Subject: [PATCH 49/79] SPI: Allow specifying the parsers for SPI flash - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - include/linux/spi/flash.h | 5 ++++- - 1 file changed, 4 insertions(+), 1 deletion(-) - ---- a/include/linux/spi/flash.h -+++ b/include/linux/spi/flash.h -@@ -2,7 +2,7 @@ - #define LINUX_SPI_FLASH_H - - struct mtd_partition; -- -+struct mtd_part_parser_data; - /** - * struct flash_platform_data: board-specific flash data - * @name: optional flash device name (eg, as used with mtdparts=) -@@ -10,6 +10,8 @@ struct mtd_partition; - * @nr_parts: number of mtd_partitions for static partitoning - * @type: optional flash device type (e.g. m25p80 vs m25p64), for use - * with chips that can't be queried for JEDEC or other IDs -+ * @part_probe_types: optional list of MTD parser names to use for -+ * partitioning - * - * Board init code (in arch/.../mach-xxx/board-yyy.c files) can - * provide information about SPI flash parts (such as DataFlash) to -@@ -25,6 +27,7 @@ struct flash_platform_data { - - char *type; - -+ const char **part_probe_types; - /* we'll likely add more ... use JEDEC IDs, etc */ - }; - diff --git a/target/linux/brcm63xx/patches-3.6/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch b/target/linux/brcm63xx/patches-3.6/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch deleted file mode 100644 index d616ac2721..0000000000 --- a/target/linux/brcm63xx/patches-3.6/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch +++ /dev/null @@ -1,23 +0,0 @@ -From c7c3c338cb25d7f55ddb3f6bfbf3572758ca3896 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 10 Nov 2011 16:53:08 +0100 -Subject: [PATCH 50/79] MTD: DEVICES: m25p80: use parsers if provided in flash - platform data - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/mtd/devices/m25p80.c | 3 ++- - 1 file changed, 2 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/devices/m25p80.c -+++ b/drivers/mtd/devices/m25p80.c -@@ -960,7 +960,8 @@ static int __devinit m25p_probe(struct s - /* partitions should match sector boundaries; and it may be good to - * use readonly partitions for writeprotected sectors (BP2..BP0). - */ -- return mtd_device_parse_register(&flash->mtd, NULL, &ppdata, -+ return mtd_device_parse_register(&flash->mtd, -+ data ? data->part_probe_types : NULL, &ppdata, - data ? data->parts : NULL, - data ? data->nr_parts : 0); - } diff --git a/target/linux/brcm63xx/patches-3.6/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch b/target/linux/brcm63xx/patches-3.6/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch deleted file mode 100644 index 47eebba4c2..0000000000 --- a/target/linux/brcm63xx/patches-3.6/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch +++ /dev/null @@ -1,92 +0,0 @@ -From 5fb4e8d7287ac8fcb33aae8b1e9e22c5a3c392bd Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 10 Nov 2011 17:33:40 +0100 -Subject: [PATCH 51/79] MTD: DEVICES: m25p80: add support for limiting reads - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/mtd/devices/m25p80.c | 29 +++++++++++++++++++++++++++-- - include/linux/spi/flash.h | 4 ++++ - 2 files changed, 31 insertions(+), 2 deletions(-) - ---- a/drivers/mtd/devices/m25p80.c -+++ b/drivers/mtd/devices/m25p80.c -@@ -100,6 +100,7 @@ struct m25p { - u16 addr_width; - u8 erase_opcode; - u8 *command; -+ int max_transfer_len; - }; - - static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd) -@@ -343,10 +344,9 @@ static int m25p80_erase(struct mtd_info - * Read an address range from the flash chip. The address range - * may be any size provided it is within the physical boundaries. - */ --static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, -+static int __m25p80_read(struct m25p *flash, loff_t from, size_t len, - size_t *retlen, u_char *buf) - { -- struct m25p *flash = mtd_to_m25p(mtd); - struct spi_transfer t[2]; - struct spi_message m; - -@@ -395,6 +395,28 @@ static int m25p80_read(struct mtd_info * - return 0; - } - -+static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, -+ size_t *retlen, u_char *buf) -+{ -+ struct m25p *flash = mtd_to_m25p(mtd); -+ size_t off; -+ size_t read_len = flash->max_transfer_len; -+ size_t part_len; -+ int ret = 0; -+ -+ if (!read_len) -+ return __m25p80_read(flash, from, len, retlen, buf); -+ -+ *retlen = 0; -+ -+ for (off = 0; off < len && !ret; off += read_len) { -+ ret = __m25p80_read(flash, from + off, min(len - off, read_len), -+ &part_len, buf + off); -+ *retlen += part_len; -+ } -+ -+ return ret; -+} - /* - * Write an address range to the flash chip. Data must be written in - * FLASH_PAGESIZE chunks. The address range may be any size provided -@@ -871,6 +893,9 @@ static int __devinit m25p_probe(struct s - return -ENOMEM; - } - -+ if (data) -+ flash->max_transfer_len = data->max_transfer_len; -+ - flash->spi = spi; - mutex_init(&flash->lock); - dev_set_drvdata(&spi->dev, flash); ---- a/include/linux/spi/flash.h -+++ b/include/linux/spi/flash.h -@@ -13,6 +13,8 @@ struct mtd_part_parser_data; - * @part_probe_types: optional list of MTD parser names to use for - * partitioning - * -+ * @max_transfer_len: option maximum read/write length limitation for -+ * SPI controllers not able to transfer any length commands. - * Board init code (in arch/.../mach-xxx/board-yyy.c files) can - * provide information about SPI flash parts (such as DataFlash) to - * help set up the device and its appropriate default partitioning. -@@ -28,6 +30,8 @@ struct flash_platform_data { - char *type; - - const char **part_probe_types; -+ -+ unsigned int max_transfer_len; - /* we'll likely add more ... use JEDEC IDs, etc */ - }; - diff --git a/target/linux/brcm63xx/patches-3.6/300-reset_buttons.patch b/target/linux/brcm63xx/patches-3.6/300-reset_buttons.patch deleted file mode 100644 index 4161dc2c83..0000000000 --- a/target/linux/brcm63xx/patches-3.6/300-reset_buttons.patch +++ /dev/null @@ -1,116 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -12,6 +12,8 @@ - #include <linux/string.h> - #include <linux/platform_device.h> - #include <linux/ssb/ssb.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> - #include <asm/addrspace.h> - #include <bcm63xx_board.h> - #include <bcm63xx_cpu.h> -@@ -28,6 +30,9 @@ - - #define PFX "board_bcm963xx: " - -+#define BCM963XX_KEYS_POLL_INTERVAL 20 -+#define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3) -+ - static struct bcm963xx_nvram nvram; - static unsigned int mac_addr_used; - static struct board_info board; -@@ -335,6 +340,16 @@ static struct board_info __initdata boar - .active_low = 1, - }, - }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_96348gw = { -@@ -393,6 +408,16 @@ static struct board_info __initdata boar - .active_low = 1, - }, - }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_FAST2404 = { -@@ -866,11 +891,23 @@ static struct platform_device bcm63xx_gp - .dev.platform_data = &bcm63xx_led_data, - }; - -+static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = { -+ .poll_interval = BCM963XX_KEYS_POLL_INTERVAL, -+}; -+ -+static struct platform_device bcm63xx_gpio_keys_device = { -+ .name = "gpio-keys-polled", -+ .id = 0, -+ .dev.platform_data = &bcm63xx_gpio_keys_data, -+}; -+ - /* - * third stage init callback, register all board devices. - */ - int __init board_register_devices(void) - { -+ int button_count = 0; -+ - if (board.has_uart0) - bcm63xx_uart_register(0); - -@@ -913,5 +950,16 @@ int __init board_register_devices(void) - - platform_device_register(&bcm63xx_gpio_leds); - -+ /* count number of BUTTONs defined by this device */ -+ while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc) -+ button_count++; -+ -+ if (button_count) { -+ bcm63xx_gpio_keys_data.nbuttons = button_count; -+ bcm63xx_gpio_keys_data.buttons = board.buttons; -+ -+ platform_device_register(&bcm63xx_gpio_keys_device); -+ } -+ - return 0; - } ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -3,6 +3,7 @@ - - #include <linux/types.h> - #include <linux/gpio.h> -+#include <linux/gpio_keys.h> - #include <linux/leds.h> - #include <bcm63xx_dev_enet.h> - #include <bcm63xx_dev_dsp.h> -@@ -57,6 +58,9 @@ struct board_info { - - /* GPIO LEDs */ - struct gpio_led leds[5]; -+ -+ /* Buttons */ -+ struct gpio_keys_button buttons[4]; - }; - - #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/301-led_count.patch b/target/linux/brcm63xx/patches-3.6/301-led_count.patch deleted file mode 100644 index 0111bd6c08..0000000000 --- a/target/linux/brcm63xx/patches-3.6/301-led_count.patch +++ /dev/null @@ -1,41 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -907,6 +907,7 @@ static struct platform_device bcm63xx_gp - int __init board_register_devices(void) - { - int button_count = 0; -+ int led_count = 0; - - if (board.has_uart0) - bcm63xx_uart_register(0); -@@ -945,10 +946,16 @@ int __init board_register_devices(void) - - bcm63xx_flash_register(); - -- bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds); -- bcm63xx_led_data.leds = board.leds; -+ /* count number of LEDs defined by this device */ -+ while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) -+ led_count++; -+ -+ if (led_count) { -+ bcm63xx_led_data.num_leds = led_count; -+ bcm63xx_led_data.leds = board.leds; - -- platform_device_register(&bcm63xx_gpio_leds); -+ platform_device_register(&bcm63xx_gpio_leds); -+ } - - /* count number of BUTTONs defined by this device */ - while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc) ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -57,7 +57,7 @@ struct board_info { - struct bcm63xx_dsp_platform_data dsp; - - /* GPIO LEDs */ -- struct gpio_led leds[5]; -+ struct gpio_led leds[14]; - - /* Buttons */ - struct gpio_keys_button buttons[4]; diff --git a/target/linux/brcm63xx/patches-3.6/302-extended-platform-devices.patch b/target/linux/brcm63xx/patches-3.6/302-extended-platform-devices.patch deleted file mode 100644 index df9be10d3d..0000000000 --- a/target/linux/brcm63xx/patches-3.6/302-extended-platform-devices.patch +++ /dev/null @@ -1,25 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -944,6 +944,9 @@ int __init board_register_devices(void) - - bcm63xx_spi_register(); - -+ if (board.num_devs) -+ platform_add_devices(board.devs, board.num_devs); -+ - bcm63xx_flash_register(); - - /* count number of LEDs defined by this device */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -61,6 +61,10 @@ struct board_info { - - /* Buttons */ - struct gpio_keys_button buttons[4]; -+ -+ /* Additional platform devices */ -+ struct platform_device **devs; -+ unsigned int num_devs; - }; - - #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/303-spi-board-info.patch b/target/linux/brcm63xx/patches-3.6/303-spi-board-info.patch deleted file mode 100644 index b4d5388d7d..0000000000 --- a/target/linux/brcm63xx/patches-3.6/303-spi-board-info.patch +++ /dev/null @@ -1,33 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -14,6 +14,7 @@ - #include <linux/ssb/ssb.h> - #include <linux/gpio_keys.h> - #include <linux/input.h> -+#include <linux/spi/spi.h> - #include <asm/addrspace.h> - #include <bcm63xx_board.h> - #include <bcm63xx_cpu.h> -@@ -947,6 +948,9 @@ int __init board_register_devices(void) - if (board.num_devs) - platform_add_devices(board.devs, board.num_devs); - -+ if (board.num_spis) -+ spi_register_board_info(board.spis, board.num_spis); -+ - bcm63xx_flash_register(); - - /* count number of LEDs defined by this device */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -65,6 +65,10 @@ struct board_info { - /* Additional platform devices */ - struct platform_device **devs; - unsigned int num_devs; -+ -+ /* Additional platform devices */ -+ struct spi_board_info *spis; -+ unsigned int num_spis; - }; - - #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/304-boardid_fixup.patch b/target/linux/brcm63xx/patches-3.6/304-boardid_fixup.patch deleted file mode 100644 index a463fe739c..0000000000 --- a/target/linux/brcm63xx/patches-3.6/304-boardid_fixup.patch +++ /dev/null @@ -1,61 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -28,12 +28,16 @@ - #include <bcm63xx_dev_pcmcia.h> - #include <bcm63xx_dev_spi.h> - #include <board_bcm963xx.h> -+#include <linux/bcm963xx_tag.h> - - #define PFX "board_bcm963xx: " - - #define BCM963XX_KEYS_POLL_INTERVAL 20 - #define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3) - -+#define CFE_OFFSET_64K 0x10000 -+#define CFE_OFFSET_128K 0x20000 -+ - static struct bcm963xx_nvram nvram; - static unsigned int mac_addr_used; - static struct board_info board; -@@ -769,6 +773,29 @@ static int board_get_mac_address(u8 *mac - return 0; - } - -+static void __init boardid_fixup(u8 *boot_addr) -+{ -+ struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K); -+ -+ /* check if bcm_tag is at 64k offset */ -+ if (strncmp(nvram.name, tag->board_id, BOARDID_LEN) != 0) { -+ /* else try 128k */ -+ tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K); -+ if (strncmp(nvram.name, tag->board_id, BOARDID_LEN) != 0) { -+ /* No tag found */ -+ printk(KERN_DEBUG "No bcm_tag found!\n"); -+ return; -+ } -+ } -+ /* check if we should override the boardid */ -+ if (tag->information1[0] != '+') -+ return; -+ -+ strncpy(nvram.name, &tag->information1[1], BOARDID_LEN); -+ -+ printk(KERN_INFO "Overriding boardid with '%s'\n", nvram.name); -+} -+ - /* - * early init callback, read nvram data from flash and checksum it - */ -@@ -816,6 +843,11 @@ void __init board_prom_init(void) - return; - } - -+ if (strcmp(cfe_version, "unknown") != 0) { -+ /* cfe present */ -+ boardid_fixup(boot_addr); -+ } -+ - /* find board by name */ - for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) { - if (strncmp(nvram.name, bcm963xx_boards[i]->name, diff --git a/target/linux/brcm63xx/patches-3.6/305-missing_ext_irq_bits.patch b/target/linux/brcm63xx/patches-3.6/305-missing_ext_irq_bits.patch deleted file mode 100644 index 703f4b54b1..0000000000 --- a/target/linux/brcm63xx/patches-3.6/305-missing_ext_irq_bits.patch +++ /dev/null @@ -1,96 +0,0 @@ ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -56,8 +56,8 @@ static void __internal_irq_unmask_64(uns - #define is_ext_irq_cascaded 0 - #define ext_irq_start 0 - #define ext_irq_end 0 --#define ext_irq_count 0 --#define ext_irq_cfg_reg1 0 -+#define ext_irq_count 4 -+#define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_6345 - #define ext_irq_cfg_reg2 0 - #endif - #ifdef CONFIG_BCM63XX_CPU_6348 -@@ -143,11 +143,15 @@ static void bcm63xx_init_irq(void) - irq_stat_addr += PERF_IRQSTAT_6338_REG; - irq_mask_addr += PERF_IRQMASK_6338_REG; - irq_bits = 32; -+ ext_irq_count = 4; -+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6338; - break; - case BCM6345_CPU_ID: - irq_stat_addr += PERF_IRQSTAT_6345_REG; - irq_mask_addr += PERF_IRQMASK_6345_REG; - irq_bits = 32; -+ ext_irq_count = 4; -+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6345; - break; - case BCM6348_CPU_ID: - irq_stat_addr += PERF_IRQSTAT_6348_REG; -@@ -434,7 +438,8 @@ static int bcm63xx_external_irq_set_type - reg = bcm_perf_readl(regaddr); - irq %= 4; - -- if (BCMCPU_IS_6348()) { -+ switch (bcm63xx_get_cpu_id()) { -+ case BCM6348_CPU_ID: - if (levelsense) - reg |= EXTIRQ_CFG_LEVELSENSE_6348(irq); - else -@@ -447,9 +452,12 @@ static int bcm63xx_external_irq_set_type - reg |= EXTIRQ_CFG_BOTHEDGE_6348(irq); - else - reg &= ~EXTIRQ_CFG_BOTHEDGE_6348(irq); -- } -+ break; - -- if (BCMCPU_IS_6338() || BCMCPU_IS_6358() || BCMCPU_IS_6368()) { -+ case BCM6338_CPU_ID: -+ case BCM6345_CPU_ID: -+ case BCM6358_CPU_ID: -+ case BCM6368_CPU_ID: - if (levelsense) - reg |= EXTIRQ_CFG_LEVELSENSE(irq); - else -@@ -462,6 +470,9 @@ static int bcm63xx_external_irq_set_type - reg |= EXTIRQ_CFG_BOTHEDGE(irq); - else - reg &= ~EXTIRQ_CFG_BOTHEDGE(irq); -+ break; -+ default: -+ BUG(); - } - - bcm_perf_writel(reg, regaddr); ---- a/arch/mips/bcm63xx/setup.c -+++ b/arch/mips/bcm63xx/setup.c -@@ -74,6 +74,9 @@ void bcm63xx_machine_reboot(void) - case BCM6338_CPU_ID: - perf_regs[0] = PERF_EXTIRQ_CFG_REG_6338; - break; -+ case BCM6345_CPU_ID: -+ perf_regs[0] = PERF_EXTIRQ_CFG_REG_6345; -+ break; - case BCM6348_CPU_ID: - perf_regs[0] = PERF_EXTIRQ_CFG_REG_6348; - break; -@@ -83,6 +86,9 @@ void bcm63xx_machine_reboot(void) - } - - for (i = 0; i < 2; i++) { -+ if (!perf_regs[i]) -+ break; -+ - reg = bcm_perf_readl(perf_regs[i]); - if (BCMCPU_IS_6348()) { - reg &= ~EXTIRQ_CFG_MASK_ALL_6348; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -161,6 +161,7 @@ - /* External Interrupt Configuration register */ - #define PERF_EXTIRQ_CFG_REG_6328 0x18 - #define PERF_EXTIRQ_CFG_REG_6338 0x14 -+#define PERF_EXTIRQ_CFG_REG_6345 0x14 - #define PERF_EXTIRQ_CFG_REG_6348 0x14 - #define PERF_EXTIRQ_CFG_REG_6358 0x14 - #define PERF_EXTIRQ_CFG_REG_6368 0x18 diff --git a/target/linux/brcm63xx/patches-3.6/306-Revert-MIPS-BCM63XX-Call-board_register_device-from-.patch b/target/linux/brcm63xx/patches-3.6/306-Revert-MIPS-BCM63XX-Call-board_register_device-from-.patch deleted file mode 100644 index aa7ef8bbdb..0000000000 --- a/target/linux/brcm63xx/patches-3.6/306-Revert-MIPS-BCM63XX-Call-board_register_device-from-.patch +++ /dev/null @@ -1,23 +0,0 @@ -From a7d2622b6614fdca504c074a0cd307d5a1165c30 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 8 May 2012 09:39:01 +0200 -Subject: [PATCH 04/59] Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()" - -This commit causes a race between PCI scan and SSB fallback SPROM handler -registration, causing the wifi to not work on slower systems. The only -subsystem touched from board_register_device is platform device -registration, which should be safe as an arch init call. - -This reverts commit d64ed7ada2f689d2c62af1892ca55e47d3653e36. ---- - arch/mips/bcm63xx/setup.c | 2 +- - 1 files changed, 1 insertions(+), 1 deletions(-) - ---- a/arch/mips/bcm63xx/setup.c -+++ b/arch/mips/bcm63xx/setup.c -@@ -157,4 +157,4 @@ int __init bcm63xx_register_devices(void - return board_register_devices(); - } - --device_initcall(bcm63xx_register_devices); -+arch_initcall(bcm63xx_register_devices); diff --git a/target/linux/brcm63xx/patches-3.6/307-MIPS-BCM63XX-allow-second-UART-on-BCM6328.patch b/target/linux/brcm63xx/patches-3.6/307-MIPS-BCM63XX-allow-second-UART-on-BCM6328.patch deleted file mode 100644 index 1418d65bf4..0000000000 --- a/target/linux/brcm63xx/patches-3.6/307-MIPS-BCM63XX-allow-second-UART-on-BCM6328.patch +++ /dev/null @@ -1,22 +0,0 @@ -From c110865541e2d3782c412af9d48c016de5a64d9c Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 14 Jun 2011 21:14:39 +0200 -Subject: [PATCH 42/79] MIPS: BCM63XX: allow second UART on BCM6328 - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/dev-uart.c | 3 ++- - 1 file changed, 2 insertions(+), 1 deletion(-) - ---- a/arch/mips/bcm63xx/dev-uart.c -+++ b/arch/mips/bcm63xx/dev-uart.c -@@ -54,7 +54,8 @@ int __init bcm63xx_uart_register(unsigne - if (id >= ARRAY_SIZE(bcm63xx_uart_devices)) - return -ENODEV; - -- if (id == 1 && (!BCMCPU_IS_6358() && !BCMCPU_IS_6368())) -+ if (id == 1 && !BCMCPU_IS_6328() && !BCMCPU_IS_6358() && -+ !BCMCPU_IS_6368()) - return -ENODEV; - - if (id == 0) { diff --git a/target/linux/brcm63xx/patches-3.6/308-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch b/target/linux/brcm63xx/patches-3.6/308-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch deleted file mode 100644 index 8a11f8266e..0000000000 --- a/target/linux/brcm63xx/patches-3.6/308-MIPS-BCM63XX-expose-the-HS-SPI-clock.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 5aeb6273a610f8aab090b3499827177eb41311ba Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sat, 12 Nov 2011 12:19:09 +0100 -Subject: [PATCH 53/79] MIPS: BCM63XX: expose the HS SPI clock - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/clk.c | 22 ++++++++++++++++++++++ - 1 file changed, 22 insertions(+) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -194,6 +194,26 @@ static struct clk clk_spi = { - }; - - /* -+ * SPI clock -+ */ -+static void hsspi_set(struct clk *clk, int enable) -+{ -+ u32 mask; -+ -+ if (BCMCPU_IS_6328()) -+ mask = CKCTL_6328_HSSPI_EN; -+ else -+ return; -+ -+ bcm_hwclock_set(mask, enable); -+} -+ -+static struct clk clk_hsspi = { -+ .set = hsspi_set, -+}; -+ -+ -+/* - * XTM clock - */ - static void xtm_set(struct clk *clk, int enable) -@@ -286,6 +306,8 @@ struct clk *clk_get(struct device *dev, - return &clk_usbh; - if (!strcmp(id, "spi")) - return &clk_spi; -+ if (!strcmp(id, "hsspi")) -+ return &clk_hsspi; - if (!strcmp(id, "xtm")) - return &clk_xtm; - if (!strcmp(id, "periph")) diff --git a/target/linux/brcm63xx/patches-3.6/309-MIPS-BCM63XX-add-HSSPI-register-definitions.patch b/target/linux/brcm63xx/patches-3.6/309-MIPS-BCM63XX-add-HSSPI-register-definitions.patch deleted file mode 100644 index 5e2cd96d35..0000000000 --- a/target/linux/brcm63xx/patches-3.6/309-MIPS-BCM63XX-add-HSSPI-register-definitions.patch +++ /dev/null @@ -1,211 +0,0 @@ -From 70f970222bc1096689ae1bffeb9ed09a7c4bed07 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sat, 12 Nov 2011 12:19:55 +0100 -Subject: [PATCH 28/60] MIPS: BCM63XX: add HSSPI register definitions - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 18 ++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 47 +++++++++++++++++++++ - 2 files changed, 65 insertions(+), 0 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -116,6 +116,7 @@ enum bcm63xx_regs_set { - RSET_UART1, - RSET_GPIO, - RSET_SPI, -+ RSET_HSSPI, - RSET_UDC0, - RSET_OHCI0, - RSET_OHCI_PRIV, -@@ -159,6 +160,7 @@ enum bcm63xx_regs_set { - #define RSET_ENETDMA_SIZE 2048 - #define RSET_ENETSW_SIZE 65536 - #define RSET_UART_SIZE 24 -+#define RSET_HSSPI_SIZE 1536 - #define RSET_UDC_SIZE 256 - #define RSET_OHCI_SIZE 256 - #define RSET_EHCI_SIZE 256 -@@ -182,6 +184,7 @@ enum bcm63xx_regs_set { - #define BCM_6328_UART1_BASE (0xb0000120) - #define BCM_6328_GPIO_BASE (0xb0000080) - #define BCM_6328_SPI_BASE (0xdeadbeef) -+#define BCM_6328_HSSPI_BASE (0xb0001000) - #define BCM_6328_UDC0_BASE (0xdeadbeef) - #define BCM_6328_USBDMA_BASE (0xdeadbeef) - #define BCM_6328_OHCI0_BASE (0xb0002600) -@@ -227,6 +230,7 @@ enum bcm63xx_regs_set { - #define BCM_6338_UART1_BASE (0xdeadbeef) - #define BCM_6338_GPIO_BASE (0xfffe0400) - #define BCM_6338_SPI_BASE (0xfffe0c00) -+#define BCM_6338_HSSPI_BASE (0xdeadbeef) - #define BCM_6338_UDC0_BASE (0xdeadbeef) - #define BCM_6338_USBDMA_BASE (0xfffe2400) - #define BCM_6338_OHCI0_BASE (0xdeadbeef) -@@ -273,6 +277,7 @@ enum bcm63xx_regs_set { - #define BCM_6345_UART1_BASE (0xdeadbeef) - #define BCM_6345_GPIO_BASE (0xfffe0400) - #define BCM_6345_SPI_BASE (0xdeadbeef) -+#define BCM_6345_HSSPI_BASE (0xdeadbeef) - #define BCM_6345_UDC0_BASE (0xdeadbeef) - #define BCM_6345_USBDMA_BASE (0xfffe2800) - #define BCM_6345_ENET0_BASE (0xfffe1800) -@@ -318,6 +323,7 @@ enum bcm63xx_regs_set { - #define BCM_6348_UART1_BASE (0xdeadbeef) - #define BCM_6348_GPIO_BASE (0xfffe0400) - #define BCM_6348_SPI_BASE (0xfffe0c00) -+#define BCM_6348_HSSPI_BASE (0xdeadbeef) - #define BCM_6348_UDC0_BASE (0xfffe1000) - #define BCM_6348_OHCI0_BASE (0xfffe1b00) - #define BCM_6348_OHCI_PRIV_BASE (0xfffe1c00) -@@ -361,6 +367,7 @@ enum bcm63xx_regs_set { - #define BCM_6358_UART1_BASE (0xfffe0120) - #define BCM_6358_GPIO_BASE (0xfffe0080) - #define BCM_6358_SPI_BASE (0xfffe0800) -+#define BCM_6358_HSSPI_BASE (0xdeadbeef) - #define BCM_6358_UDC0_BASE (0xfffe0800) - #define BCM_6358_OHCI0_BASE (0xfffe1400) - #define BCM_6358_OHCI_PRIV_BASE (0xdeadbeef) -@@ -405,6 +412,7 @@ enum bcm63xx_regs_set { - #define BCM_6368_UART1_BASE (0xb0000120) - #define BCM_6368_GPIO_BASE (0xb0000080) - #define BCM_6368_SPI_BASE (0xb0000800) -+#define BCM_6368_HSSPI_BASE (0xdeadbeef) - #define BCM_6368_UDC0_BASE (0xdeadbeef) - #define BCM_6368_OHCI0_BASE (0xb0001600) - #define BCM_6368_OHCI_PRIV_BASE (0xdeadbeef) -@@ -454,6 +462,7 @@ extern const unsigned long *bcm63xx_regs - __GEN_RSET_BASE(__cpu, UART1) \ - __GEN_RSET_BASE(__cpu, GPIO) \ - __GEN_RSET_BASE(__cpu, SPI) \ -+ __GEN_RSET_BASE(__cpu, HSSPI) \ - __GEN_RSET_BASE(__cpu, UDC0) \ - __GEN_RSET_BASE(__cpu, OHCI0) \ - __GEN_RSET_BASE(__cpu, OHCI_PRIV) \ -@@ -495,6 +504,7 @@ extern const unsigned long *bcm63xx_regs - [RSET_UART1] = BCM_## __cpu ##_UART1_BASE, \ - [RSET_GPIO] = BCM_## __cpu ##_GPIO_BASE, \ - [RSET_SPI] = BCM_## __cpu ##_SPI_BASE, \ -+ [RSET_HSSPI] = BCM_## __cpu ##_HSSPI_BASE, \ - [RSET_UDC0] = BCM_## __cpu ##_UDC0_BASE, \ - [RSET_OHCI0] = BCM_## __cpu ##_OHCI0_BASE, \ - [RSET_OHCI_PRIV] = BCM_## __cpu ##_OHCI_PRIV_BASE, \ -@@ -567,6 +577,7 @@ enum bcm63xx_irq { - IRQ_ENET0, - IRQ_ENET1, - IRQ_ENET_PHY, -+ IRQ_HSSPI, - IRQ_OHCI0, - IRQ_EHCI0, - IRQ_ENET0_RXDMA, -@@ -602,6 +613,7 @@ enum bcm63xx_irq { - #define BCM_6328_ENET0_IRQ 0 - #define BCM_6328_ENET1_IRQ 0 - #define BCM_6328_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12) -+#define BCM_6328_HSSPI_IRQ (IRQ_INTERNAL_BASE + 29) - #define BCM_6328_OHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 9) - #define BCM_6328_EHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 10) - #define BCM_6328_PCMCIA_IRQ 0 -@@ -640,6 +652,7 @@ enum bcm63xx_irq { - #define BCM_6338_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6338_ENET1_IRQ 0 - #define BCM_6338_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6338_HSSPI_IRQ 0 - #define BCM_6338_OHCI0_IRQ 0 - #define BCM_6338_EHCI0_IRQ 0 - #define BCM_6338_ENET0_RXDMA_IRQ (IRQ_INTERNAL_BASE + 15) -@@ -671,6 +684,7 @@ enum bcm63xx_irq { - #define BCM_6345_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6345_ENET1_IRQ 0 - #define BCM_6345_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12) -+#define BCM_6345_HSSPI_IRQ 0 - #define BCM_6345_OHCI0_IRQ 0 - #define BCM_6345_EHCI0_IRQ 0 - #define BCM_6345_ENET0_RXDMA_IRQ (IRQ_INTERNAL_BASE + 13 + 1) -@@ -702,6 +716,7 @@ enum bcm63xx_irq { - #define BCM_6348_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6348_ENET1_IRQ (IRQ_INTERNAL_BASE + 7) - #define BCM_6348_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6348_HSSPI_IRQ 0 - #define BCM_6348_OHCI0_IRQ (IRQ_INTERNAL_BASE + 12) - #define BCM_6348_EHCI0_IRQ 0 - #define BCM_6348_ENET0_RXDMA_IRQ (IRQ_INTERNAL_BASE + 20) -@@ -733,6 +748,7 @@ enum bcm63xx_irq { - #define BCM_6358_ENET0_IRQ (IRQ_INTERNAL_BASE + 8) - #define BCM_6358_ENET1_IRQ (IRQ_INTERNAL_BASE + 6) - #define BCM_6358_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6358_HSSPI_IRQ 0 - #define BCM_6358_OHCI0_IRQ (IRQ_INTERNAL_BASE + 5) - #define BCM_6358_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10) - #define BCM_6358_ENET0_RXDMA_IRQ (IRQ_INTERNAL_BASE + 15) -@@ -773,6 +789,7 @@ enum bcm63xx_irq { - #define BCM_6368_ENET0_IRQ 0 - #define BCM_6368_ENET1_IRQ 0 - #define BCM_6368_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 15) -+#define BCM_6368_HSSPI_IRQ 0 - #define BCM_6368_OHCI0_IRQ (IRQ_INTERNAL_BASE + 5) - #define BCM_6368_EHCI0_IRQ (IRQ_INTERNAL_BASE + 7) - #define BCM_6368_PCMCIA_IRQ 0 -@@ -813,6 +830,7 @@ extern const int *bcm63xx_irqs; - [IRQ_ENET0] = BCM_## __cpu ##_ENET0_IRQ, \ - [IRQ_ENET1] = BCM_## __cpu ##_ENET1_IRQ, \ - [IRQ_ENET_PHY] = BCM_## __cpu ##_ENET_PHY_IRQ, \ -+ [IRQ_HSSPI] = BCM_## __cpu ##_HSSPI_IRQ, \ - [IRQ_OHCI0] = BCM_## __cpu ##_OHCI0_IRQ, \ - [IRQ_EHCI0] = BCM_## __cpu ##_EHCI0_IRQ, \ - [IRQ_ENET0_RXDMA] = BCM_## __cpu ##_ENET0_RXDMA_IRQ, \ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1239,4 +1239,51 @@ - - #define PCIE_DEVICE_OFFSET 0x8000 - -+/************************************************************************* -+ * _REG relative to RSET_HSSPI -+ *************************************************************************/ -+ -+#define HSSPI_GLOBAL_CTRL_REG 0x0 -+#define GLOBAL_CTRL_CLK_POLARITY (1 << 17) -+#define GLOBAL_CTRL_CLK_GATE_SSOFF (1 << 16) -+ -+#define HSSPI_GLOBAL_EXT_TRIGGER_REG 0x4 -+ -+#define HSSPI_INT_STATUS_REG 0x8 -+#define HSSPI_INT_STATUS_MASKED_REG 0xc -+#define HSSPI_INT_MASK_REG 0x10 -+ -+#define HSSPI_PING0_CMD_DONE (1 << 0) -+ -+#define HSSPI_INT_CLEAR_ALL 0xff001f1f -+ -+#define HSSPI_PINGPONG_COMMAND_REG(x) (0x80 + (x) * 0x40) -+#define PINGPONG_CMD_COMMAND_MASK 0xf -+#define PINGPONG_COMMAND_NOOP 0 -+#define PINGPONG_COMMAND_START_NOW 1 -+#define PINGPONG_COMMAND_START_TRIGGER 2 -+#define PINGPONG_COMMAND_HALT 3 -+#define PINGPONG_COMMAND_FLUSH 4 -+#define PINGPONG_CMD_PROFILE_SHIFT 8 -+#define PINGPONG_CMD_SS_SHIFT 12 -+ -+#define HSSPI_PINGPONG_STATUS_REG(x) (0x84 + (x) * 0x40) -+ -+#define HSSPI_PROFILE_CLK_CTRL_REG(x) (0x100 + (x) * 0x20) -+#define CLK_CTRL_ACCUM_RST_ON_LOOP (1 << 15) -+ -+#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x) (0x104 + (x) * 0x20) -+#define SIGNAL_CTRL_LATCH_RISING (1 << 12) -+#define SIGNAL_CTRL_LAUNCH_RISING (1 << 13) -+#define SIGNAL_CTRL_ASYNC_INPUT_PATH (1 << 16) -+ -+#define HSSPI_PROFILE_MODE_CTRL_REG(x) (0x108 + (x) * 0x20) -+#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT 8 -+#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT 12 -+#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT 16 -+#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT 18 -+#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT 24 -+ -+#define HSSPI_FIFO_REG(x) (0x200 + (x) * 0x200) -+ - #endif /* BCM63XX_REGS_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/310-board_leds_naming.patch b/target/linux/brcm63xx/patches-3.6/310-board_leds_naming.patch deleted file mode 100644 index 8b307a2fed..0000000000 --- a/target/linux/brcm63xx/patches-3.6/310-board_leds_naming.patch +++ /dev/null @@ -1,267 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -103,28 +103,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl", -+ .name = "96338GW:green:adsl", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ses", -+ .name = "96338GW:green:ses", - .gpio = 5, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96338GW:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96338GW:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96338GW:green:stop", - .gpio = 1, - .active_low = 1, - } -@@ -144,28 +144,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl", -+ .name = "96338W:green:adsl", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ses", -+ .name = "96338W:green:ses", - .gpio = 5, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96338W:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96338W:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96338W:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -204,29 +204,29 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348R:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348R:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348R:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348R:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - - }, - { -- .name = "stop", -+ .name = "96348R:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -265,28 +265,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348GW-10:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348GW-10:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348GW-10:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348GW-10:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96348GW-10:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -319,28 +319,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348GW-11:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348GW-11:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348GW-11:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348GW-11:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96348GW-11:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -387,28 +387,28 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96348GW:green:adsl-fail", - .gpio = 2, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96348GW:green:ppp", - .gpio = 3, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96348GW:green:ppp-fail", - .gpio = 4, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96348GW:green:power", - .gpio = 0, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96348GW:green:stop", - .gpio = 1, - .active_low = 1, - }, -@@ -540,27 +540,27 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl-fail", -+ .name = "96358VW:green:adsl-fail", - .gpio = 15, - .active_low = 1, - }, - { -- .name = "ppp", -+ .name = "96358VW:green:ppp", - .gpio = 22, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96358VW:green:ppp-fail", - .gpio = 23, - .active_low = 1, - }, - { -- .name = "power", -+ .name = "96358VW:green:power", - .gpio = 4, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96358VW:green:stop", - .gpio = 5, - }, - }, -@@ -592,22 +592,22 @@ static struct board_info __initdata boar - - .leds = { - { -- .name = "adsl", -+ .name = "96358VW2:green:adsl", - .gpio = 22, - .active_low = 1, - }, - { -- .name = "ppp-fail", -+ .name = "96358VW2:green:ppp-fail", - .gpio = 23, - }, - { -- .name = "power", -+ .name = "96358VW2:green:power", - .gpio = 5, - .active_low = 1, - .default_trigger = "default-on", - }, - { -- .name = "stop", -+ .name = "96358VW2:green:stop", - .gpio = 4, - .active_low = 1, - }, diff --git a/target/linux/brcm63xx/patches-3.6/311-cfe_version_mod.patch b/target/linux/brcm63xx/patches-3.6/311-cfe_version_mod.patch deleted file mode 100644 index 835b85ffd8..0000000000 --- a/target/linux/brcm63xx/patches-3.6/311-cfe_version_mod.patch +++ /dev/null @@ -1,26 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -822,6 +822,8 @@ void __init board_prom_init(void) - if (!memcmp(cfe, "cfe-v", 5)) - snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u", - cfe[5], cfe[6], cfe[7], cfe[8], cfe[9]); -+ else if (!memcmp(cfe, "cfe-", 4)) -+ snprintf(cfe_version, 16, "%s", (char *) &cfe[4]); - else - strcpy(cfe_version, "unknown"); - printk(KERN_INFO PFX "CFE version: %s\n", cfe_version); ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -54,10 +54,10 @@ static int bcm63xx_detect_cfe(struct mtd - if (ret) - return ret; - -- if (strncmp("cfe-v", buf, 5) == 0) -+ if (strncmp("cfe-", buf, 4) == 0) - return 0; - -- /* very old CFE's do not have the cfe-v string, so check for magic */ -+ /* very old CFE's do not have the cfe- string, so check for magic */ - ret = mtd_read(master, BCM63XX_CFE_MAGIC_OFFSET, 8, &retlen, - (void *)buf); - buf[retlen] = 0; diff --git a/target/linux/brcm63xx/patches-3.6/312-MIPS-BCM63XX-add-basic-BCM6362-support.patch b/target/linux/brcm63xx/patches-3.6/312-MIPS-BCM63XX-add-basic-BCM6362-support.patch deleted file mode 100644 index 9d2e101dee..0000000000 --- a/target/linux/brcm63xx/patches-3.6/312-MIPS-BCM63XX-add-basic-BCM6362-support.patch +++ /dev/null @@ -1,497 +0,0 @@ -From 27ebbb819b1f92d52309276b29b7a56e362e5c4d Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Mon, 21 Nov 2011 00:48:52 +0100 -Subject: [PATCH 54/84] MIPS: BCM63XX: add basic BCM6362 support - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/Kconfig | 4 + - arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +- - arch/mips/bcm63xx/cpu.c | 52 ++++++++- - arch/mips/bcm63xx/irq.c | 19 +++ - arch/mips/bcm63xx/prom.c | 2 + - arch/mips/bcm63xx/setup.c | 3 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 139 +++++++++++++++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h | 2 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 59 +++++++++ - arch/mips/include/asm/mach-bcm63xx/ioremap.h | 1 + - 10 files changed, 281 insertions(+), 2 deletions(-) - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -25,6 +25,10 @@ config BCM63XX_CPU_6358 - bool "support 6358 CPU" - select HW_HAS_PCI - -+config BCM63XX_CPU_6362 -+ bool "support 6362 CPU" -+ select HW_HAS_PCI -+ - config BCM63XX_CPU_6368 - bool "support 6368 CPU" - select HW_HAS_PCI ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -809,7 +809,7 @@ void __init board_prom_init(void) - /* read base address of boot chip select (0) - * 6328 does not have MPI but boots from a fixed address - */ -- if (BCMCPU_IS_6328()) -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) - val = 0x18000000; - else { - val = bcm_mpi_readl(MPI_CSBASE_REG(0)); ---- a/arch/mips/bcm63xx/cpu.c -+++ b/arch/mips/bcm63xx/cpu.c -@@ -71,6 +71,15 @@ static const int bcm6358_irqs[] = { - - }; - -+static const unsigned long bcm6362_regs_base[] = { -+ __GEN_CPU_REGS_TABLE(6362) -+}; -+ -+static const int bcm6362_irqs[] = { -+ __GEN_CPU_IRQ_TABLE(6362) -+ -+}; -+ - static const unsigned long bcm6368_regs_base[] = { - __GEN_CPU_REGS_TABLE(6368) - }; -@@ -169,6 +178,42 @@ static unsigned int detect_cpu_clock(voi - return (16 * 1000000 * n1 * n2) / m1; - } - -+ case BCM6362_CPU_ID: -+ { -+ unsigned int tmp, mips_pll_fcvo; -+ -+ tmp = bcm_misc_readl(MISC_STRAPBUS_6362_REG); -+ mips_pll_fcvo = (tmp & STRAPBUS_6362_FCVO_MASK) -+ >> STRAPBUS_6362_FCVO_SHIFT; -+ switch (mips_pll_fcvo) { -+ case 0x03: -+ case 0x0b: -+ case 0x13: -+ case 0x1b: -+ return 240000000; -+ case 0x04: -+ case 0x0c: -+ case 0x14: -+ case 0x1c: -+ return 160000000; -+ case 0x05: -+ case 0x0e: -+ case 0x16: -+ case 0x1e: -+ case 0x1f: -+ return 400000000; -+ case 0x06: -+ return 440000000; -+ case 0x07: -+ case 0x17: -+ return 384000000; -+ case 0x15: -+ case 0x1d: -+ return 200000000; -+ default: -+ return 320000000; -+ } -+ } - case BCM6368_CPU_ID: - { - unsigned int tmp, p1, p2, ndiv, m1; -@@ -205,7 +250,7 @@ static unsigned int detect_memory_size(v - unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0; - u32 val; - -- if (BCMCPU_IS_6328()) -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) - return bcm_ddr_readl(DDR_CSEND_REG) << 24; - - if (BCMCPU_IS_6345()) { -@@ -280,6 +325,11 @@ void __init bcm63xx_cpu_init(void) - bcm63xx_regs_base = bcm6328_regs_base; - bcm63xx_irqs = bcm6328_irqs; - break; -+ case BCM6362_CPU_ID: -+ expected_cpu_id = BCM6362_CPU_ID; -+ bcm63xx_regs_base = bcm6362_regs_base; -+ bcm63xx_irqs = bcm6362_irqs; -+ break; - case BCM6368_CPU_ID: - expected_cpu_id = BCM6368_CPU_ID; - bcm63xx_regs_base = bcm6368_regs_base; ---- a/arch/mips/bcm63xx/irq.c -+++ b/arch/mips/bcm63xx/irq.c -@@ -82,6 +82,14 @@ static void __internal_irq_unmask_64(uns - #define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_6358 - #define ext_irq_cfg_reg2 0 - #endif -+#ifdef CONFIG_BCM63XX_CPU_6362 -+#define irq_stat_reg PERF_IRQSTAT_6362_REG -+#define irq_mask_reg PERF_IRQMASK_6362_REG -+#define irq_bits 64 -+#define is_ext_irq_cascaded 1 -+#define ext_irq_start (BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE) -+#define ext_irq_end (BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE) -+#endif - #ifdef CONFIG_BCM63XX_CPU_6368 - #define irq_stat_reg PERF_IRQSTAT_6368_REG - #define irq_mask_reg PERF_IRQMASK_6368_REG -@@ -170,6 +178,16 @@ static void bcm63xx_init_irq(void) - ext_irq_end = BCM_6358_EXT_IRQ3 - IRQ_INTERNAL_BASE; - ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358; - break; -+ case BCM6362_CPU_ID: -+ irq_stat_addr += PERF_IRQSTAT_6362_REG; -+ irq_mask_addr += PERF_IRQMASK_6362_REG; -+ irq_bits = 64; -+ ext_irq_count = 4; -+ is_ext_irq_cascaded = 1; -+ ext_irq_start = BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE; -+ ext_irq_end = BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE; -+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362; -+ break; - case BCM6368_CPU_ID: - irq_stat_addr += PERF_IRQSTAT_6368_REG; - irq_mask_addr += PERF_IRQMASK_6368_REG; -@@ -457,6 +475,7 @@ static int bcm63xx_external_irq_set_type - case BCM6338_CPU_ID: - case BCM6345_CPU_ID: - case BCM6358_CPU_ID: -+ case BCM6362_CPU_ID: - case BCM6368_CPU_ID: - if (levelsense) - reg |= EXTIRQ_CFG_LEVELSENSE(irq); ---- a/arch/mips/bcm63xx/prom.c -+++ b/arch/mips/bcm63xx/prom.c -@@ -36,6 +36,8 @@ void __init prom_init(void) - mask = CKCTL_6348_ALL_SAFE_EN; - else if (BCMCPU_IS_6358()) - mask = CKCTL_6358_ALL_SAFE_EN; -+ else if (BCMCPU_IS_6362()) -+ mask = CKCTL_6362_ALL_SAFE_EN; - else if (BCMCPU_IS_6368()) - mask = CKCTL_6368_ALL_SAFE_EN; - else ---- a/arch/mips/bcm63xx/setup.c -+++ b/arch/mips/bcm63xx/setup.c -@@ -83,6 +83,9 @@ void bcm63xx_machine_reboot(void) - case BCM6358_CPU_ID: - perf_regs[0] = PERF_EXTIRQ_CFG_REG_6358; - break; -+ case BCM6362_CPU_ID: -+ perf_regs[0] = PERF_EXTIRQ_CFG_REG_6362; -+ break; - } - - for (i = 0; i < 2; i++) { ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -14,6 +14,7 @@ - #define BCM6345_CPU_ID 0x6345 - #define BCM6348_CPU_ID 0x6348 - #define BCM6358_CPU_ID 0x6358 -+#define BCM6362_CPU_ID 0x6362 - #define BCM6368_CPU_ID 0x6368 - - void __init bcm63xx_cpu_init(void); -@@ -86,6 +87,20 @@ unsigned int bcm63xx_get_cpu_freq(void); - # define BCMCPU_IS_6358() (0) - #endif - -+#ifdef CONFIG_BCM63XX_CPU_6362 -+# ifdef bcm63xx_get_cpu_id -+# undef bcm63xx_get_cpu_id -+# define bcm63xx_get_cpu_id() __bcm63xx_get_cpu_id() -+# define BCMCPU_RUNTIME_DETECT -+# else -+# define bcm63xx_get_cpu_id() BCM6362_CPU_ID -+# endif -+# define BCMCPU_IS_6362() (bcm63xx_get_cpu_id() == BCM6362_CPU_ID) -+#else -+# define BCMCPU_IS_6362() (0) -+#endif -+ -+ - #ifdef CONFIG_BCM63XX_CPU_6368 - # ifdef bcm63xx_get_cpu_id - # undef bcm63xx_get_cpu_id -@@ -402,6 +417,62 @@ enum bcm63xx_regs_set { - - - /* -+ * 6362 register sets base address -+ */ -+#define BCM_6362_DSL_LMEM_BASE (0xdeadbeef) -+#define BCM_6362_PERF_BASE (0xb0000000) -+#define BCM_6362_TIMER_BASE (0xb0000040) -+#define BCM_6362_WDT_BASE (0xb000005c) -+#define BCM_6362_UART0_BASE (0xb0000100) -+#define BCM_6362_UART1_BASE (0xb0000120) -+#define BCM_6362_GPIO_BASE (0xb0000080) -+#define BCM_6362_SPI_BASE (0xb0000800) -+#define BCM_6362_HSSPI_BASE (0xb0001000) -+#define BCM_6362_UDC0_BASE (0xdeadbeef) -+#define BCM_6362_USBDMA_BASE (0xb000c000) -+#define BCM_6362_OHCI0_BASE (0xb0002600) -+#define BCM_6362_OHCI_PRIV_BASE (0xdeadbeef) -+#define BCM_6362_USBH_PRIV_BASE (0xb0002700) -+#define BCM_6362_USBD_BASE (0xb0002400) -+#define BCM_6362_MPI_BASE (0xdeadbeef) -+#define BCM_6362_PCMCIA_BASE (0xdeadbeef) -+#define BCM_6362_PCIE_BASE (0xb0e40000) -+#define BCM_6362_SDRAM_REGS_BASE (0xdeadbeef) -+#define BCM_6362_DSL_BASE (0xdeadbeef) -+#define BCM_6362_UBUS_BASE (0xdeadbeef) -+#define BCM_6362_ENET0_BASE (0xdeadbeef) -+#define BCM_6362_ENET1_BASE (0xdeadbeef) -+#define BCM_6362_ENETDMA_BASE (0xb000d800) -+#define BCM_6362_ENETDMAC_BASE (0xb000da00) -+#define BCM_6362_ENETDMAS_BASE (0xb000dc00) -+#define BCM_6362_ENETSW_BASE (0xb0e00000) -+#define BCM_6362_EHCI0_BASE (0xb0002500) -+#define BCM_6362_SDRAM_BASE (0xdeadbeef) -+#define BCM_6362_MEMC_BASE (0xdeadbeef) -+#define BCM_6362_DDR_BASE (0xb0003000) -+#define BCM_6362_M2M_BASE (0xdeadbeef) -+#define BCM_6362_ATM_BASE (0xdeadbeef) -+#define BCM_6362_XTM_BASE (0xb0007800) -+#define BCM_6362_XTMDMA_BASE (0xb000b800) -+#define BCM_6362_XTMDMAC_BASE (0xdeadbeef) -+#define BCM_6362_XTMDMAS_BASE (0xdeadbeef) -+#define BCM_6362_PCM_BASE (0xb000a800) -+#define BCM_6362_PCMDMA_BASE (0xdeadbeef) -+#define BCM_6362_PCMDMAC_BASE (0xdeadbeef) -+#define BCM_6362_PCMDMAS_BASE (0xdeadbeef) -+#define BCM_6362_RNG_BASE (0xdeadbeef) -+#define BCM_6362_MISC_BASE (0xb0001800) -+ -+#define BCM_6362_NAND_REG_BASE (0xb0000200) -+#define BCM_6362_NAND_CACHE_BASE (0xb0000600) -+#define BCM_6362_LED_BASE (0xb0001900) -+#define BCM_6362_IPSEC_BASE (0xb0002800) -+#define BCM_6362_IPSEC_DMA_BASE (0xb000d000) -+#define BCM_6362_WLAN_CHIPCOMMON_BASE (0xb0004000) -+#define BCM_6362_WLAN_D11_BASE (0xb0005000) -+#define BCM_6362_WLAN_SHIM_BASE (0xb0007000) -+ -+/* - * 6368 register sets base address - */ - #define BCM_6368_DSL_LMEM_BASE (0xdeadbeef) -@@ -557,6 +628,9 @@ static inline unsigned long bcm63xx_regs - #ifdef CONFIG_BCM63XX_CPU_6358 - __GEN_RSET(6358) - #endif -+#ifdef CONFIG_BCM63XX_CPU_6362 -+ __GEN_RSET(6362) -+#endif - #ifdef CONFIG_BCM63XX_CPU_6368 - __GEN_RSET(6368) - #endif -@@ -777,6 +851,71 @@ enum bcm63xx_irq { - #define BCM_6358_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28) - - /* -+ * 6362 irqs -+ */ -+#define BCM_6362_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32) -+ -+#define BCM_6362_TIMER_IRQ (IRQ_INTERNAL_BASE + 0) -+#define BCM_6362_SPI_IRQ (IRQ_INTERNAL_BASE + 2) -+#define BCM_6362_UART0_IRQ (IRQ_INTERNAL_BASE + 3) -+#define BCM_6362_UART1_IRQ (IRQ_INTERNAL_BASE + 4) -+#define BCM_6362_DSL_IRQ (IRQ_INTERNAL_BASE + 28) -+#define BCM_6362_UDC0_IRQ 0 -+#define BCM_6362_ENET0_IRQ 0 -+#define BCM_6362_ENET1_IRQ 0 -+#define BCM_6362_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 14) -+#define BCM_6362_HSSPI_IRQ (IRQ_INTERNAL_BASE + 5) -+#define BCM_6362_OHCI0_IRQ (IRQ_INTERNAL_BASE + 9) -+#define BCM_6362_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10) -+#define BCM_6362_USBD_IRQ (IRQ_INTERNAL_BASE + 11) -+#define BCM_6362_USBD_RXDMA0_IRQ (IRQ_INTERNAL_BASE + 20) -+#define BCM_6362_USBD_TXDMA0_IRQ (IRQ_INTERNAL_BASE + 21) -+#define BCM_6362_USBD_RXDMA1_IRQ (IRQ_INTERNAL_BASE + 22) -+#define BCM_6362_USBD_TXDMA1_IRQ (IRQ_INTERNAL_BASE + 23) -+#define BCM_6362_USBD_RXDMA2_IRQ (IRQ_INTERNAL_BASE + 24) -+#define BCM_6362_USBD_TXDMA2_IRQ (IRQ_INTERNAL_BASE + 25) -+#define BCM_6362_PCMCIA_IRQ 0 -+#define BCM_6362_ENET0_RXDMA_IRQ 0 -+#define BCM_6362_ENET0_TXDMA_IRQ 0 -+#define BCM_6362_ENET1_RXDMA_IRQ 0 -+#define BCM_6362_ENET1_TXDMA_IRQ 0 -+#define BCM_6362_PCI_IRQ (IRQ_INTERNAL_BASE + 30) -+#define BCM_6362_ATM_IRQ 0 -+#define BCM_6362_ENETSW_RXDMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 0) -+#define BCM_6362_ENETSW_RXDMA1_IRQ (BCM_6362_HIGH_IRQ_BASE + 1) -+#define BCM_6362_ENETSW_RXDMA2_IRQ (BCM_6362_HIGH_IRQ_BASE + 2) -+#define BCM_6362_ENETSW_RXDMA3_IRQ (BCM_6362_HIGH_IRQ_BASE + 3) -+#define BCM_6362_ENETSW_TXDMA0_IRQ 0 -+#define BCM_6362_ENETSW_TXDMA1_IRQ 0 -+#define BCM_6362_ENETSW_TXDMA2_IRQ 0 -+#define BCM_6362_ENETSW_TXDMA3_IRQ 0 -+#define BCM_6362_XTM_IRQ 0 -+#define BCM_6362_XTM_DMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 12) -+ -+#define BCM_6362_RING_OSC_IRQ (IRQ_INTERNAL_BASE + 1) -+#define BCM_6362_WLAN_GPIO_IRQ (IRQ_INTERNAL_BASE + 6) -+#define BCM_6362_WLAN_IRQ (IRQ_INTERNAL_BASE + 7) -+#define BCM_6362_IPSEC_IRQ (IRQ_INTERNAL_BASE + 8) -+#define BCM_6362_NAND_IRQ (IRQ_INTERNAL_BASE + 12) -+#define BCM_6362_PCM_IRQ (IRQ_INTERNAL_BASE + 13) -+#define BCM_6362_DG_IRQ (IRQ_INTERNAL_BASE + 15) -+#define BCM_6362_EPHY_ENERGY0_IRQ (IRQ_INTERNAL_BASE + 16) -+#define BCM_6362_EPHY_ENERGY1_IRQ (IRQ_INTERNAL_BASE + 17) -+#define BCM_6362_EPHY_ENERGY2_IRQ (IRQ_INTERNAL_BASE + 18) -+#define BCM_6362_EPHY_ENERGY3_IRQ (IRQ_INTERNAL_BASE + 19) -+#define BCM_6362_IPSEC_DMA0_IRQ (IRQ_INTERNAL_BASE + 26) -+#define BCM_6362_IPSEC_DMA1_IRQ (IRQ_INTERNAL_BASE + 27) -+#define BCM_6362_FAP0_IRQ (IRQ_INTERNAL_BASE + 29) -+#define BCM_6362_PCM_DMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 4) -+#define BCM_6362_PCM_DMA1_IRQ (BCM_6362_HIGH_IRQ_BASE + 5) -+#define BCM_6362_DECT0_IRQ (BCM_6362_HIGH_IRQ_BASE + 6) -+#define BCM_6362_DECT1_IRQ (BCM_6362_HIGH_IRQ_BASE + 7) -+#define BCM_6362_EXT_IRQ0 (BCM_6362_HIGH_IRQ_BASE + 8) -+#define BCM_6362_EXT_IRQ1 (BCM_6362_HIGH_IRQ_BASE + 9) -+#define BCM_6362_EXT_IRQ2 (BCM_6362_HIGH_IRQ_BASE + 10) -+#define BCM_6362_EXT_IRQ3 (BCM_6362_HIGH_IRQ_BASE + 11) -+ -+/* - * 6368 irqs - */ - #define BCM_6368_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h -@@ -17,6 +17,8 @@ static inline unsigned long bcm63xx_gpio - return 8; - case BCM6345_CPU_ID: - return 16; -+ case BCM6362_CPU_ID: -+ return 48; - case BCM6368_CPU_ID: - return 38; - case BCM6348_CPU_ID: ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -107,6 +107,39 @@ - CKCTL_6358_USBSU_EN | \ - CKCTL_6358_EPHY_EN) - -+#define CKCTL_6362_ADSL_QPROC_EN (1 << 1) -+#define CKCTL_6362_ADSL_AFE_EN (1 << 2) -+#define CKCTL_6362_ADSL_EN (1 << 3) -+#define CKCTL_6362_MIPS_EN (1 << 4) -+#define CKCTL_6362_WLAN_OCP_EN (1 << 5) -+#define CKCTL_6362_SWPKT_USB_EN (1 << 7) -+#define CKCTL_6362_SWPKT_SAR_EN (1 << 8) -+#define CKCTL_6362_SAR_EN (1 << 9) -+#define CKCTL_6362_ROBOSW_EN (1 << 10) -+#define CKCTL_6362_PCM_EN (1 << 11) -+#define CKCTL_6362_USBD_EN (1 << 12) -+#define CKCTL_6362_USBH_EN (1 << 13) -+#define CKCTL_6362_IPSEC_EN (1 << 14) -+#define CKCTL_6362_SPI_EN (1 << 15) -+#define CKCTL_6362_HSSPI_EN (1 << 16) -+#define CKCTL_6362_PCIE_EN (1 << 17) -+#define CKCTL_6362_FAP_EN (1 << 18) -+#define CKCTL_6362_PHYMIPS_EN (1 << 19) -+#define CKCTL_6362_NAND_EN (1 << 20) -+ -+#define CKCTL_6362_ALL_SAFE_EN (CKCTL_6362_PHYMIPS_EN | \ -+ CKCTL_6362_ADSL_QPROC_EN | \ -+ CKCTL_6362_ADSL_AFE_EN | \ -+ CKCTL_6362_ADSL_EN | \ -+ CKCTL_6362_SAR_EN | \ -+ CKCTL_6362_PCM_EN | \ -+ CKCTL_6362_IPSEC_EN | \ -+ CKCTL_6362_USBD_EN | \ -+ CKCTL_6362_USBH_EN | \ -+ CKCTL_6362_ROBOSW_EN | \ -+ CKCTL_6362_PCIE_EN) -+ -+ - #define CKCTL_6368_VDSL_QPROC_EN (1 << 2) - #define CKCTL_6368_VDSL_AFE_EN (1 << 3) - #define CKCTL_6368_VDSL_BONDING_EN (1 << 4) -@@ -148,6 +181,7 @@ - #define PERF_IRQMASK_6345_REG 0xc - #define PERF_IRQMASK_6348_REG 0xc - #define PERF_IRQMASK_6358_REG 0xc -+#define PERF_IRQMASK_6362_REG 0x20 - #define PERF_IRQMASK_6368_REG 0x20 - - /* Interrupt Status register */ -@@ -156,6 +190,7 @@ - #define PERF_IRQSTAT_6345_REG 0x10 - #define PERF_IRQSTAT_6348_REG 0x10 - #define PERF_IRQSTAT_6358_REG 0x10 -+#define PERF_IRQSTAT_6362_REG 0x28 - #define PERF_IRQSTAT_6368_REG 0x28 - - /* External Interrupt Configuration register */ -@@ -164,6 +199,7 @@ - #define PERF_EXTIRQ_CFG_REG_6345 0x14 - #define PERF_EXTIRQ_CFG_REG_6348 0x14 - #define PERF_EXTIRQ_CFG_REG_6358 0x14 -+#define PERF_EXTIRQ_CFG_REG_6362 0x18 - #define PERF_EXTIRQ_CFG_REG_6368 0x18 - - #define PERF_EXTIRQ_CFG_REG2_6368 0x1c -@@ -191,6 +227,7 @@ - /* Soft Reset register */ - #define PERF_SOFTRESET_REG 0x28 - #define PERF_SOFTRESET_6328_REG 0x10 -+#define PERF_SOFTRESET_6362_REG 0x10 - #define PERF_SOFTRESET_6368_REG 0x10 - - #define SOFTRESET_6328_SPI_MASK (1 << 0) -@@ -244,6 +281,22 @@ - SOFTRESET_6348_ACLC_MASK | \ - SOFTRESET_6348_ADSLMIPSPLL_MASK) - -+#define SOFTRESET_6362_SPI_MASK (1 << 0) -+#define SOFTRESET_6362_IPSEC_MASK (1 << 1) -+#define SOFTRESET_6362_EPHY_MASK (1 << 2) -+#define SOFTRESET_6362_SAR_MASK (1 << 3) -+#define SOFTRESET_6362_ENETSW_MASK (1 << 4) -+#define SOFTRESET_6362_USBS_MASK (1 << 5) -+#define SOFTRESET_6362_USBH_MASK (1 << 6) -+#define SOFTRESET_6362_PCM_MASK (1 << 7) -+#define SOFTRESET_6362_PCIE_CORE_MASK (1 << 8) -+#define SOFTRESET_6362_PCIE_MASK (1 << 9) -+#define SOFTRESET_6362_PCIE_EXT_MASK (1 << 10) -+#define SOFTRESET_6362_WLAN_SHIM_MASK (1 << 11) -+#define SOFTRESET_6362_DDR_PHY_MASK (1 << 12) -+#define SOFTRESET_6362_FAP_MASK (1 << 13) -+#define SOFTRESET_6362_WLAN_UBUS_MASK (1 << 14) -+ - #define SOFTRESET_6368_SPI_MASK (1 << 0) - #define SOFTRESET_6368_MPI_MASK (1 << 3) - #define SOFTRESET_6368_EPHY_MASK (1 << 6) -@@ -1182,6 +1235,12 @@ - #define SERDES_PCIE_EN (1 << 0) - #define SERDES_PCIE_EXD_EN (1 << 15) - -+#define MISC_STRAPBUS_6362_REG 0x14 -+#define STRAPBUS_6362_FCVO_SHIFT 1 -+#define STRAPBUS_6362_FCVO_MASK (0x1f << STRAPBUS_6362_FCVO_SHIFT) -+#define STRAPBUS_6362_BOOT_SEL_SERIAL (1 << 15) -+#define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15) -+ - #define MISC_STRAPBUS_6328_REG 0x240 - #define STRAPBUS_6328_FCVO_SHIFT 7 - #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT) ---- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h -+++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h -@@ -19,6 +19,7 @@ static inline int is_bcm63xx_internal_re - return 1; - break; - case BCM6328_CPU_ID: -+ case BCM6362_CPU_ID: - case BCM6368_CPU_ID: - if (offset >= 0xb0000000 && offset < 0xb1000000) - return 1; diff --git a/target/linux/brcm63xx/patches-3.6/313-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.6/313-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch deleted file mode 100644 index 36024d10b4..0000000000 --- a/target/linux/brcm63xx/patches-3.6/313-MIPS-BCM63XX-enable-pcie-for-BCM6362.patch +++ /dev/null @@ -1,110 +0,0 @@ -From e49546bf3f255f028d0877ceeb7ed6466fe37d8a Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Mon, 21 Nov 2011 00:53:26 +0100 -Subject: [PATCH 56/84] MIPS: BCM63XX: enable pcie for BCM6362 - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 3 +- - arch/mips/pci/pci-bcm63xx.c | 57 +++++++++++++++------ - 2 files changed, 44 insertions(+), 16 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1231,7 +1231,8 @@ - /************************************************************************* - * _REG relative to RSET_MISC - *************************************************************************/ --#define MISC_SERDES_CTRL_REG 0x0 -+#define MISC_SERDES_CTRL_6328_REG 0x0 -+#define MISC_SERDES_CTRL_6362_REG 0x4 - #define SERDES_PCIE_EN (1 << 0) - #define SERDES_PCIE_EXD_EN (1 << 15) - ---- a/arch/mips/pci/pci-bcm63xx.c -+++ b/arch/mips/pci/pci-bcm63xx.c -@@ -118,35 +118,61 @@ void __iomem *pci_iospace_start; - static void __init bcm63xx_reset_pcie(void) - { - u32 val; -+ u32 reg; -+ u32 mask; - - /* enable clock */ -+ -+ if (BCMCPU_IS_6328()) -+ mask = CKCTL_6328_PCIE_EN; -+ else -+ mask = CKCTL_6362_PCIE_EN; -+ - val = bcm_perf_readl(PERF_CKCTL_REG); -- val |= CKCTL_6328_PCIE_EN; -+ val |= mask; - bcm_perf_writel(val, PERF_CKCTL_REG); - - /* enable SERDES */ -- val = bcm_misc_readl(MISC_SERDES_CTRL_REG); -+ -+ if (BCMCPU_IS_6328()) -+ reg = MISC_SERDES_CTRL_6328_REG; -+ else -+ reg = MISC_SERDES_CTRL_6362_REG; -+ -+ val = bcm_misc_readl(reg); - val |= SERDES_PCIE_EN | SERDES_PCIE_EXD_EN; -- bcm_misc_writel(val, MISC_SERDES_CTRL_REG); -+ bcm_misc_writel(val, reg); - - /* reset the PCIe core */ -- val = bcm_perf_readl(PERF_SOFTRESET_6328_REG); -+ if (BCMCPU_IS_6328()) { -+ reg = PERF_SOFTRESET_6328_REG; -+ mask = SOFTRESET_6328_PCIE_MASK | SOFTRESET_6328_PCIE_CORE_MASK -+ | SOFTRESET_6328_PCIE_HARD_MASK; -+ } else { -+ reg = PERF_SOFTRESET_6362_REG; -+ mask = SOFTRESET_6362_PCIE_MASK | SOFTRESET_6362_PCIE_CORE_MASK; -+ } -+ val = bcm_perf_readl(reg); -+ val &= ~mask; -+ -+ if (BCMCPU_IS_6328()) -+ val &= ~SOFTRESET_6328_PCIE_EXT_MASK; -+ else -+ val &= ~SOFTRESET_6362_PCIE_EXT_MASK; - -- val &= ~SOFTRESET_6328_PCIE_MASK; -- val &= ~SOFTRESET_6328_PCIE_CORE_MASK; -- val &= ~SOFTRESET_6328_PCIE_HARD_MASK; -- val &= ~SOFTRESET_6328_PCIE_EXT_MASK; -- bcm_perf_writel(val, PERF_SOFTRESET_6328_REG); -+ bcm_perf_writel(val, reg); - mdelay(10); - -- val |= SOFTRESET_6328_PCIE_MASK; -- val |= SOFTRESET_6328_PCIE_CORE_MASK; -- val |= SOFTRESET_6328_PCIE_HARD_MASK; -- bcm_perf_writel(val, PERF_SOFTRESET_6328_REG); -+ val |= mask; -+ bcm_perf_writel(val, reg); - mdelay(10); - -- val |= SOFTRESET_6328_PCIE_EXT_MASK; -- bcm_perf_writel(val, PERF_SOFTRESET_6328_REG); -+ if (BCMCPU_IS_6328()) -+ val |= SOFTRESET_6328_PCIE_EXT_MASK; -+ else -+ val |= SOFTRESET_6362_PCIE_EXT_MASK; -+ -+ bcm_perf_writel(val, reg); - mdelay(200); - } - -@@ -332,6 +358,7 @@ static int __init bcm63xx_pci_init(void) - - switch (bcm63xx_get_cpu_id()) { - case BCM6328_CPU_ID: -+ case BCM6362_CPU_ID: - return bcm63xx_register_pcie(); - case BCM6348_CPU_ID: - case BCM6358_CPU_ID: diff --git a/target/linux/brcm63xx/patches-3.6/400-ohci-add-driver-for-bcm63xx-integrated-controller.patch b/target/linux/brcm63xx/patches-3.6/400-ohci-add-driver-for-bcm63xx-integrated-controller.patch deleted file mode 100644 index 572419cb68..0000000000 --- a/target/linux/brcm63xx/patches-3.6/400-ohci-add-driver-for-bcm63xx-integrated-controller.patch +++ /dev/null @@ -1,235 +0,0 @@ -From 7b510c5754d3c46e1287803f51e8ecb177414438 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Fri, 10 Jun 2011 19:14:30 +0200 -Subject: [PATCH 23/63] ohci: add driver for bcm63xx integrated controller. - ---- - drivers/usb/host/Kconfig | 9 ++ - drivers/usb/host/ohci-bcm63xx.c | 175 +++++++++++++++++++++++++++++++++++++++ - drivers/usb/host/ohci-hcd.c | 5 + - drivers/usb/host/ohci.h | 2 +- - 4 files changed, 190 insertions(+), 1 deletions(-) - create mode 100644 drivers/usb/host/ohci-bcm63xx.c - ---- a/drivers/usb/host/Kconfig -+++ b/drivers/usb/host/Kconfig -@@ -306,6 +306,15 @@ config USB_OHCI_HCD - To compile this driver as a module, choose M here: the - module will be called ohci-hcd. - -+config USB_OHCI_BCM63XX -+ bool "Support for Broadcom 63xx on-chip OHCI USB controller" -+ depends on USB_OHCI_HCD && BCM63XX -+ select USB_OHCI_BIG_ENDIAN_DESC -+ select USB_OHCI_BIG_ENDIAN_MMIO -+ ---help--- -+ Enables support for the on-chip OHCI controller on -+ BCM63XX chips. -+ - config USB_OHCI_HCD_OMAP1 - bool "OHCI support for OMAP1/2 chips" - depends on USB_OHCI_HCD && ARCH_OMAP1 ---- /dev/null -+++ b/drivers/usb/host/ohci-bcm63xx.c -@@ -0,0 +1,176 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> -+ */ -+ -+#include <linux/init.h> -+#include <linux/clk.h> -+#include <linux/platform_device.h> -+#include <bcm63xx_cpu.h> -+#include <bcm63xx_regs.h> -+#include <bcm63xx_io.h> -+ -+static struct clk *usb_host_clock; -+ -+static int __devinit ohci_bcm63xx_start(struct usb_hcd *hcd) -+{ -+ struct ohci_hcd *ohci = hcd_to_ohci(hcd); -+ int ret; -+ -+ ohci->num_ports = 1; -+ -+ ret = ohci_init(ohci); -+ if (ret < 0) -+ return ret; -+ -+ /* FIXME: autodetected port 2 is shared with USB slave */ -+ -+ ret = ohci_run(ohci); -+ if (ret < 0) { -+ dev_err(hcd->self.controller, "can't start %s\n", -+ hcd->self.bus_name); -+ ohci_stop(hcd); -+ return ret; -+ } -+ return 0; -+} -+ -+static const struct hc_driver ohci_bcm63xx_hc_driver = { -+ .description = hcd_name, -+ .product_desc = "BCM63XX integrated OHCI controller", -+ .hcd_priv_size = sizeof(struct ohci_hcd), -+ -+ .irq = ohci_irq, -+ .flags = HCD_USB11 | HCD_MEMORY, -+ .start = ohci_bcm63xx_start, -+ .stop = ohci_stop, -+ .shutdown = ohci_shutdown, -+ .urb_enqueue = ohci_urb_enqueue, -+ .urb_dequeue = ohci_urb_dequeue, -+ .endpoint_disable = ohci_endpoint_disable, -+ .get_frame_number = ohci_get_frame, -+ .hub_status_data = ohci_hub_status_data, -+ .hub_control = ohci_hub_control, -+ .start_port_reset = ohci_start_port_reset, -+}; -+ -+static int __devinit ohci_hcd_bcm63xx_drv_probe(struct platform_device *pdev) -+{ -+ struct resource *res_mem; -+ struct usb_hcd *hcd; -+ struct ohci_hcd *ohci; -+ struct clk *clk; -+ u32 reg; -+ int ret, irq; -+ -+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ irq = platform_get_irq(pdev, 0); -+ if (!res_mem || irq < 0) -+ return -ENODEV; -+ -+ /* enable USB host clock */ -+ clk = clk_get(&pdev->dev, "usbh"); -+ if (IS_ERR(clk)) -+ return -ENODEV; -+ -+ clk_enable(clk); -+ usb_host_clock = clk; -+ msleep(100); -+ -+ if (BCMCPU_IS_6348()) -+ bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG); -+ else if (BCMCPU_IS_6358()) { -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG); -+ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; -+ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG); -+ /* -+ * The magic value comes for the original vendor BSP -+ * and is needed for USB to work. Datasheet does not -+ * help, so the magic value is used as-is. -+ */ -+ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, -+ USBH_PRIV_TEST_6358_REG); -+ -+ } else if (BCMCPU_IS_6368()) { -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); -+ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; -+ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); -+ -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); -+ reg |= USBH_PRIV_SETUP_IOC_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); -+ } -+ -+ hcd = usb_create_hcd(&ohci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx"); -+ if (!hcd) -+ return -ENOMEM; -+ hcd->rsrc_start = res_mem->start; -+ hcd->rsrc_len = res_mem->end - res_mem->start + 1; -+ -+ if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { -+ pr_debug("request_mem_region failed\n"); -+ ret = -EBUSY; -+ goto out; -+ } -+ -+ hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); -+ if (!hcd->regs) { -+ pr_debug("ioremap failed\n"); -+ ret = -EIO; -+ goto out1; -+ } -+ -+ ohci = hcd_to_ohci(hcd); -+ ohci->flags |= OHCI_QUIRK_BE_MMIO | OHCI_QUIRK_BE_DESC | -+ OHCI_QUIRK_FRAME_NO; -+ ohci_hcd_init(ohci); -+ -+ ret = usb_add_hcd(hcd, irq, IRQF_DISABLED); -+ if (ret) -+ goto out2; -+ -+ platform_set_drvdata(pdev, hcd); -+ return 0; -+ -+out2: -+ iounmap(hcd->regs); -+out1: -+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len); -+out: -+ usb_put_hcd(hcd); -+ return ret; -+} -+ -+static int __devexit ohci_hcd_bcm63xx_drv_remove(struct platform_device *pdev) -+{ -+ struct usb_hcd *hcd; -+ -+ hcd = platform_get_drvdata(pdev); -+ usb_remove_hcd(hcd); -+ iounmap(hcd->regs); -+ usb_put_hcd(hcd); -+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len); -+ if (usb_host_clock) { -+ clk_disable(usb_host_clock); -+ clk_put(usb_host_clock); -+ } -+ platform_set_drvdata(pdev, NULL); -+ return 0; -+} -+ -+static struct platform_driver ohci_hcd_bcm63xx_driver = { -+ .probe = ohci_hcd_bcm63xx_drv_probe, -+ .remove = __devexit_p(ohci_hcd_bcm63xx_drv_remove), -+ .shutdown = usb_hcd_platform_shutdown, -+ .driver = { -+ .name = "bcm63xx_ohci", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+MODULE_ALIAS("platform:bcm63xx_ohci"); ---- a/drivers/usb/host/ohci-hcd.c -+++ b/drivers/usb/host/ohci-hcd.c -@@ -1120,6 +1120,11 @@ MODULE_LICENSE ("GPL"); - #define OHCI_PLATFORM_DRIVER ohci_platform_driver - #endif - -+#ifdef CONFIG_USB_OHCI_BCM63XX -+#include "ohci-bcm63xx.c" -+#define PLATFORM_DRIVER ohci_hcd_bcm63xx_driver -+#endif -+ - #if !defined(PCI_DRIVER) && \ - !defined(PLATFORM_DRIVER) && \ - !defined(OMAP1_PLATFORM_DRIVER) && \ ---- a/drivers/usb/host/ohci.h -+++ b/drivers/usb/host/ohci.h -@@ -647,7 +647,7 @@ static inline u32 hc32_to_cpup (const st - * some big-endian SOC implementations. Same thing happens with PSW access. - */ - --#ifdef CONFIG_PPC_MPC52xx -+#if defined(CONFIG_PPC_MPC52xx) || defined(CONFIG_BCM63XX) - #define big_endian_frame_no_quirk(ohci) (ohci->flags & OHCI_QUIRK_FRAME_NO) - #else - #define big_endian_frame_no_quirk(ohci) 0 diff --git a/target/linux/brcm63xx/patches-3.6/401-MIPS-BCM63XX-register-ohci-device.patch b/target/linux/brcm63xx/patches-3.6/401-MIPS-BCM63XX-register-ohci-device.patch deleted file mode 100644 index 28a7e2f1f3..0000000000 --- a/target/linux/brcm63xx/patches-3.6/401-MIPS-BCM63XX-register-ohci-device.patch +++ /dev/null @@ -1,143 +0,0 @@ -From ab96f20ca1c3c8e7e5acd82d1e50823a5d572675 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Tue, 24 May 2011 21:47:41 +0200 -Subject: [PATCH 24/63] MIPS: BCM63XX: register ohci device. - ---- - arch/mips/bcm63xx/Kconfig | 9 ++-- - arch/mips/bcm63xx/Makefile | 2 +- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++ - arch/mips/bcm63xx/dev-usb-ohci.c | 50 ++++++++++++++++++++ - .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h | 6 ++ - 5 files changed, 65 insertions(+), 6 deletions(-) - create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -8,22 +8,20 @@ config BCM63XX_CPU_6328 - config BCM63XX_CPU_6338 - bool "support 6338 CPU" - select HW_HAS_PCI -- select USB_ARCH_HAS_OHCI -- select USB_OHCI_BIG_ENDIAN_DESC -- select USB_OHCI_BIG_ENDIAN_MMIO -+ select USB_ARCH_HAS_OHCI if USB_SUPPORT - - config BCM63XX_CPU_6345 - bool "support 6345 CPU" -- select USB_OHCI_BIG_ENDIAN_DESC -- select USB_OHCI_BIG_ENDIAN_MMIO - - config BCM63XX_CPU_6348 - bool "support 6348 CPU" - select HW_HAS_PCI -+ select USB_ARCH_HAS_OHCI if USB_SUPPORT - - config BCM63XX_CPU_6358 - bool "support 6358 CPU" - select HW_HAS_PCI -+ select USB_ARCH_HAS_OHCI if USB_SUPPORT - - config BCM63XX_CPU_6362 - bool "support 6362 CPU" -@@ -32,6 +30,7 @@ config BCM63XX_CPU_6362 - config BCM63XX_CPU_6368 - bool "support 6368 CPU" - select HW_HAS_PCI -+ select USB_ARCH_HAS_OHCI if USB_SUPPORT - endmenu - - source "arch/mips/bcm63xx/boards/Kconfig" ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,6 +1,6 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \ - dev-dsp.o dev-enet.o dev-flash.o dev-pcmcia.o dev-rng.o \ -- dev-spi.o dev-uart.o dev-wdt.o -+ dev-spi.o dev-uart.o dev-usb-ohci.o dev-wdt.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -27,6 +27,7 @@ - #include <bcm63xx_dev_flash.h> - #include <bcm63xx_dev_pcmcia.h> - #include <bcm63xx_dev_spi.h> -+#include <bcm63xx_dev_usb_ohci.h> - #include <board_bcm963xx.h> - #include <linux/bcm963xx_tag.h> - -@@ -961,6 +962,9 @@ int __init board_register_devices(void) - !board_get_mac_address(board.enet1.mac_addr)) - bcm63xx_enet_register(1, &board.enet1); - -+ if (board.has_ohci0) -+ bcm63xx_ohci_register(); -+ - if (board.has_dsp) - bcm63xx_dsp_register(&board.dsp); - ---- /dev/null -+++ b/arch/mips/bcm63xx/dev-usb-ohci.c -@@ -0,0 +1,50 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> -+ */ -+ -+#include <linux/init.h> -+#include <linux/kernel.h> -+#include <linux/platform_device.h> -+#include <bcm63xx_cpu.h> -+#include <bcm63xx_dev_usb_ohci.h> -+ -+static struct resource ohci_resources[] = { -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static u64 ohci_dmamask = ~(u32)0; -+ -+static struct platform_device bcm63xx_ohci_device = { -+ .name = "bcm63xx_ohci", -+ .id = 0, -+ .num_resources = ARRAY_SIZE(ohci_resources), -+ .resource = ohci_resources, -+ .dev = { -+ .dma_mask = &ohci_dmamask, -+ .coherent_dma_mask = 0xffffffff, -+ }, -+}; -+ -+int __init bcm63xx_ohci_register(void) -+{ -+ if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358() && !BCMCPU_IS_6368()) -+ return 0; -+ -+ ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0); -+ ohci_resources[0].end = ohci_resources[0].start; -+ ohci_resources[0].end += RSET_OHCI_SIZE - 1; -+ ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0); -+ return platform_device_register(&bcm63xx_ohci_device); -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h -@@ -0,0 +1,6 @@ -+#ifndef BCM63XX_DEV_USB_OHCI_H_ -+#define BCM63XX_DEV_USB_OHCI_H_ -+ -+int bcm63xx_ohci_register(void); -+ -+#endif /* BCM63XX_DEV_USB_OHCI_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/402-ehci-add-driver-for-bcm63xx-integrated-controller.patch b/target/linux/brcm63xx/patches-3.6/402-ehci-add-driver-for-bcm63xx-integrated-controller.patch deleted file mode 100644 index 207e9813a0..0000000000 --- a/target/linux/brcm63xx/patches-3.6/402-ehci-add-driver-for-bcm63xx-integrated-controller.patch +++ /dev/null @@ -1,242 +0,0 @@ -From db58271d5152aa1d3894fdef13ca04379139d5d9 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Fri, 10 Jun 2011 19:15:47 +0200 -Subject: [PATCH 25/63] ehci: add driver for bcm63xx integrated controller. - ---- - drivers/usb/host/Kconfig | 10 ++- - drivers/usb/host/ehci-bcm63xx.c | 186 +++++++++++++++++++++++++++++++++++++++ - drivers/usb/host/ehci-hcd.c | 5 + - 3 files changed, 199 insertions(+), 1 deletions(-) - create mode 100644 drivers/usb/host/ehci-bcm63xx.c - ---- a/drivers/usb/host/Kconfig -+++ b/drivers/usb/host/Kconfig -@@ -110,7 +110,8 @@ config USB_EHCI_BIG_ENDIAN_MMIO - depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || \ - ARCH_IXP4XX || XPS_USB_HCD_XILINX || \ - PPC_MPC512x || CPU_CAVIUM_OCTEON || \ -- PMC_MSP || SPARC_LEON || MIPS_SEAD3) -+ PMC_MSP || SPARC_LEON || MIPS_SEAD3 || \ -+ BCM63XX) - default y - - config USB_EHCI_BIG_ENDIAN_DESC -@@ -134,6 +135,14 @@ config XPS_USB_HCD_XILINX - config USB_FSL_MPH_DR_OF - tristate - -+config USB_EHCI_BCM63XX -+ bool "Support for Broadcom 63xx on-chip EHCI USB controller" -+ depends on USB_EHCI_HCD && BCM63XX -+ select USB_EHCI_BIG_ENDIAN_MMIO -+ ---help--- -+ Enables support for the on-chip EHCI controller on -+ BCM6358 and later chips. -+ - config USB_EHCI_FSL - bool "Support for Freescale PPC on-chip EHCI USB controller" - depends on USB_EHCI_HCD && FSL_SOC ---- /dev/null -+++ b/drivers/usb/host/ehci-bcm63xx.c -@@ -0,0 +1,186 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> -+ */ -+ -+#include <linux/init.h> -+#include <linux/clk.h> -+#include <linux/platform_device.h> -+#include <bcm63xx_cpu.h> -+#include <bcm63xx_regs.h> -+#include <bcm63xx_io.h> -+ -+static struct clk *usb_host_clock; -+ -+static int ehci_bcm63xx_setup(struct usb_hcd *hcd) -+{ -+ struct ehci_hcd *ehci = hcd_to_ehci(hcd); -+ int retval; -+ -+ retval = ehci_halt(ehci); -+ if (retval) -+ return retval; -+ -+ retval = ehci_init(hcd); -+ if (retval) -+ return retval; -+ -+ ehci_reset(ehci); -+ ehci_port_power(ehci, 0); -+ -+ return retval; -+} -+ -+ -+static const struct hc_driver ehci_bcm63xx_hc_driver = { -+ .description = hcd_name, -+ .product_desc = "BCM63XX integrated EHCI controller", -+ .hcd_priv_size = sizeof(struct ehci_hcd), -+ -+ .irq = ehci_irq, -+ .flags = HCD_MEMORY | HCD_USB2, -+ -+ .reset = ehci_bcm63xx_setup, -+ .start = ehci_run, -+ .stop = ehci_stop, -+ .shutdown = ehci_shutdown, -+ -+ .urb_enqueue = ehci_urb_enqueue, -+ .urb_dequeue = ehci_urb_dequeue, -+ .endpoint_disable = ehci_endpoint_disable, -+ -+ .get_frame_number = ehci_get_frame, -+ -+ .hub_status_data = ehci_hub_status_data, -+ .hub_control = ehci_hub_control, -+ .bus_suspend = ehci_bus_suspend, -+ .bus_resume = ehci_bus_resume, -+ .relinquish_port = ehci_relinquish_port, -+ .port_handed_over = ehci_port_handed_over, -+}; -+ -+static int __devinit ehci_hcd_bcm63xx_drv_probe(struct platform_device *pdev) -+{ -+ struct resource *res_mem; -+ struct usb_hcd *hcd; -+ struct ehci_hcd *ehci; -+ struct clk *clk; -+ u32 reg; -+ int ret, irq; -+ -+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ irq = platform_get_irq(pdev, 0);; -+ if (!res_mem || irq < 0) -+ return -ENODEV; -+ -+ /* enable USB host clock */ -+ clk = clk_get(&pdev->dev, "usbh"); -+ if (IS_ERR(clk)) -+ return -ENODEV; -+ -+ clk_enable(clk); -+ usb_host_clock = clk; -+ msleep(100); -+ -+ if (BCMCPU_IS_6358()) { -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG); -+ reg &= ~USBH_PRIV_SWAP_EHCI_DATA_MASK; -+ reg |= USBH_PRIV_SWAP_EHCI_ENDN_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG); -+ -+ /* -+ * The magic value comes for the original vendor BSP -+ * and is needed for USB to work. Datasheet does not -+ * help, so the magic value is used as-is. -+ */ -+ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, -+ USBH_PRIV_TEST_6358_REG); -+ -+ } else if (BCMCPU_IS_6368()) { -+ -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); -+ reg &= ~USBH_PRIV_SWAP_EHCI_DATA_MASK; -+ reg |= USBH_PRIV_SWAP_EHCI_ENDN_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); -+ -+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); -+ reg |= USBH_PRIV_SETUP_IOC_MASK; -+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); -+ } -+ -+ hcd = usb_create_hcd(&ehci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx"); -+ if (!hcd) -+ return -ENOMEM; -+ hcd->rsrc_start = res_mem->start; -+ hcd->rsrc_len = res_mem->end - res_mem->start + 1; -+ -+ if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { -+ pr_debug("request_mem_region failed\n"); -+ ret = -EBUSY; -+ goto out; -+ } -+ -+ hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); -+ if (!hcd->regs) { -+ pr_debug("ioremap failed\n"); -+ ret = -EIO; -+ goto out1; -+ } -+ -+ ehci = hcd_to_ehci(hcd); -+ ehci->big_endian_mmio = 1; -+ ehci->big_endian_desc = 0; -+ ehci->caps = hcd->regs; -+ ehci->regs = hcd->regs + -+ HC_LENGTH(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase)); -+ ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); -+ ehci->sbrn = 0x20; -+ ehci->ignore_oc = 1; -+ -+ ret = usb_add_hcd(hcd, irq, IRQF_DISABLED); -+ if (ret) -+ goto out2; -+ -+ platform_set_drvdata(pdev, hcd); -+ return 0; -+ -+out2: -+ iounmap(hcd->regs); -+out1: -+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len); -+out: -+ usb_put_hcd(hcd); -+ return ret; -+} -+ -+static int __devexit ehci_hcd_bcm63xx_drv_remove(struct platform_device *pdev) -+{ -+ struct usb_hcd *hcd; -+ -+ hcd = platform_get_drvdata(pdev); -+ usb_remove_hcd(hcd); -+ iounmap(hcd->regs); -+ usb_put_hcd(hcd); -+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len); -+ if (usb_host_clock) { -+ clk_disable(usb_host_clock); -+ clk_put(usb_host_clock); -+ } -+ platform_set_drvdata(pdev, NULL); -+ return 0; -+} -+ -+static struct platform_driver ehci_hcd_bcm63xx_driver = { -+ .probe = ehci_hcd_bcm63xx_drv_probe, -+ .remove = __devexit_p(ehci_hcd_bcm63xx_drv_remove), -+ .shutdown = usb_hcd_platform_shutdown, -+ .driver = { -+ .name = "bcm63xx_ehci", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+MODULE_ALIAS("platform:bcm63xx_ehci"); ---- a/drivers/usb/host/ehci-hcd.c -+++ b/drivers/usb/host/ehci-hcd.c -@@ -1339,6 +1339,11 @@ MODULE_LICENSE ("GPL"); - #define EHCI_PLATFORM_DRIVER ehci_platform_driver - #endif - -+#ifdef CONFIG_USB_EHCI_BCM63XX -+#include "ehci-bcm63xx.c" -+#define PLATFORM_DRIVER ehci_hcd_bcm63xx_driver -+#endif -+ - #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \ - !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \ - !defined(XILINX_OF_PLATFORM_DRIVER) && !defined(EHCI_PLATFORM_DRIVER) diff --git a/target/linux/brcm63xx/patches-3.6/403-MIPS-BCM63XX-register-ehci-device.patch b/target/linux/brcm63xx/patches-3.6/403-MIPS-BCM63XX-register-ehci-device.patch deleted file mode 100644 index eb27ed96d3..0000000000 --- a/target/linux/brcm63xx/patches-3.6/403-MIPS-BCM63XX-register-ehci-device.patch +++ /dev/null @@ -1,125 +0,0 @@ -From a2d78246e4cb45b5978fc682aad19c0fff0cd20d Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Tue, 24 May 2011 21:50:33 +0200 -Subject: [PATCH 26/63] MIPS: BCM63XX: register ehci device. - ---- - arch/mips/bcm63xx/Kconfig | 2 + - arch/mips/bcm63xx/Makefile | 2 +- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++ - arch/mips/bcm63xx/dev-usb-ehci.c | 50 ++++++++++++++++++++ - .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h | 6 ++ - 5 files changed, 63 insertions(+), 1 deletions(-) - create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -22,6 +22,7 @@ config BCM63XX_CPU_6358 - bool "support 6358 CPU" - select HW_HAS_PCI - select USB_ARCH_HAS_OHCI if USB_SUPPORT -+ select USB_ARCH_HAS_EHCI if USB_SUPPORT - - config BCM63XX_CPU_6362 - bool "support 6362 CPU" -@@ -31,6 +32,7 @@ config BCM63XX_CPU_6368 - bool "support 6368 CPU" - select HW_HAS_PCI - select USB_ARCH_HAS_OHCI if USB_SUPPORT -+ select USB_ARCH_HAS_EHCI if USB_SUPPORT - endmenu - - source "arch/mips/bcm63xx/boards/Kconfig" ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,6 +1,6 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \ - dev-dsp.o dev-enet.o dev-flash.o dev-pcmcia.o dev-rng.o \ -- dev-spi.o dev-uart.o dev-usb-ohci.o dev-wdt.o -+ dev-spi.o dev-uart.o dev-usb-ehci.o dev-usb-ohci.o dev-wdt.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -28,6 +28,7 @@ - #include <bcm63xx_dev_pcmcia.h> - #include <bcm63xx_dev_spi.h> - #include <bcm63xx_dev_usb_ohci.h> -+#include <bcm63xx_dev_usb_ehci.h> - #include <board_bcm963xx.h> - #include <linux/bcm963xx_tag.h> - -@@ -962,6 +963,9 @@ int __init board_register_devices(void) - !board_get_mac_address(board.enet1.mac_addr)) - bcm63xx_enet_register(1, &board.enet1); - -+ if (board.has_ehci0) -+ bcm63xx_ehci_register(); -+ - if (board.has_ohci0) - bcm63xx_ohci_register(); - ---- /dev/null -+++ b/arch/mips/bcm63xx/dev-usb-ehci.c -@@ -0,0 +1,50 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> -+ */ -+ -+#include <linux/init.h> -+#include <linux/kernel.h> -+#include <linux/platform_device.h> -+#include <bcm63xx_cpu.h> -+#include <bcm63xx_dev_usb_ehci.h> -+ -+static struct resource ehci_resources[] = { -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static u64 ehci_dmamask = ~(u32)0; -+ -+static struct platform_device bcm63xx_ehci_device = { -+ .name = "bcm63xx_ehci", -+ .id = 0, -+ .num_resources = ARRAY_SIZE(ehci_resources), -+ .resource = ehci_resources, -+ .dev = { -+ .dma_mask = &ehci_dmamask, -+ .coherent_dma_mask = 0xffffffff, -+ }, -+}; -+ -+int __init bcm63xx_ehci_register(void) -+{ -+ if (!BCMCPU_IS_6358() && !BCMCPU_IS_6368()) -+ return 0; -+ -+ ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); -+ ehci_resources[0].end = ehci_resources[0].start; -+ ehci_resources[0].end += RSET_EHCI_SIZE - 1; -+ ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0); -+ return platform_device_register(&bcm63xx_ehci_device); -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h -@@ -0,0 +1,6 @@ -+#ifndef BCM63XX_DEV_USB_EHCI_H_ -+#define BCM63XX_DEV_USB_EHCI_H_ -+ -+int bcm63xx_ehci_register(void); -+ -+#endif /* BCM63XX_DEV_USB_EHCI_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/404-bcm963xx_flashmap.patch b/target/linux/brcm63xx/patches-3.6/404-bcm963xx_flashmap.patch deleted file mode 100644 index 1aadfff476..0000000000 --- a/target/linux/brcm63xx/patches-3.6/404-bcm963xx_flashmap.patch +++ /dev/null @@ -1,65 +0,0 @@ -From a4d005c91d403d9f3d0272db6cc46202c06ec774 Mon Sep 17 00:00:00 2001 -From: Axel Gembe <ago@bastart.eu.org> -Date: Mon, 12 May 2008 18:54:09 +0200 -Subject: [PATCH] bcm963xx: flashmap support - -Signed-off-by: Axel Gembe <ago@bastart.eu.org> ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 19 +---------------- - drivers/mtd/maps/bcm963xx-flash.c | 32 ++++++++++++++++++++++++---- - drivers/mtd/redboot.c | 13 +++++++++-- - 3 files changed, 38 insertions(+), 26 deletions(-) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -30,7 +30,7 @@ static struct mtd_partition mtd_partitio - } - }; - --static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL }; -+static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL }; - - static struct physmap_flash_data flash_data = { - .width = 2, ---- a/drivers/mtd/redboot.c -+++ b/drivers/mtd/redboot.c -@@ -72,6 +72,7 @@ static int parse_redboot_partitions(stru - int nulllen = 0; - int numslots; - unsigned long offset; -+ unsigned long fis_origin = 0; - #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED - static char nullstring[] = "unallocated"; - #endif -@@ -176,6 +177,16 @@ static int parse_redboot_partitions(stru - goto out; - } - -+ if (data && data->origin) { -+ fis_origin = data->origin; -+ } else { -+ for (i = 0; i < numslots; i++) { -+ if (!strncmp(buf[i].name, "RedBoot", 8)) { -+ fis_origin = (buf[i].flash_base & (master->size << 1) - 1); -+ } -+ } -+ } -+ - for (i = 0; i < numslots; i++) { - struct fis_list *new_fl, **prev; - -@@ -196,10 +207,10 @@ static int parse_redboot_partitions(stru - goto out; - } - new_fl->img = &buf[i]; -- if (data && data->origin) -- buf[i].flash_base -= data->origin; -- else -- buf[i].flash_base &= master->size-1; -+ if (fis_origin) -+ buf[i].flash_base -= fis_origin; -+ -+ buf[i].flash_base &= (master->size << 1) - 1; - - /* I'm sure the JFFS2 code has done me permanent damage. - * I now think the following is _normal_ diff --git a/target/linux/brcm63xx/patches-3.6/405-bcm963xx_real_rootfs_length.patch b/target/linux/brcm63xx/patches-3.6/405-bcm963xx_real_rootfs_length.patch deleted file mode 100644 index f0e6c4c78b..0000000000 --- a/target/linux/brcm63xx/patches-3.6/405-bcm963xx_real_rootfs_length.patch +++ /dev/null @@ -1,27 +0,0 @@ ---- a/include/linux/bcm963xx_tag.h -+++ b/include/linux/bcm963xx_tag.h -@@ -85,8 +85,10 @@ struct bcm_tag { - __u32 rootfs_crc; - /* 224-227: CRC32 of kernel partition */ - __u32 kernel_crc; -- /* 228-235: Unused at present */ -- char reserved1[8]; -+ /* 228-231: Image sequence number */ -+ char image_sequence[4]; -+ /* 222-235: Openwrt: real rootfs length */ -+ __u32 real_rootfs_length; - /* 236-239: CRC32 of header excluding last 20 bytes */ - __u32 header_crc; - /* 240-255: Unused at present */ ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -131,7 +131,8 @@ static int bcm63xx_parse_cfe_partitions( - } else { - /* OpenWrt layout */ - rootfsaddr = kerneladdr + kernellen; -- rootfslen = spareaddr - rootfsaddr; -+ rootfslen = buf->real_rootfs_length; -+ spareaddr = rootfsaddr + rootfslen; - } - } else { - pr_warn("CFE boot tag CRC invalid (expected %08x, actual %08x)\n", diff --git a/target/linux/brcm63xx/patches-3.6/406_bcm63xx_enet_vlan_incoming_fixed.patch b/target/linux/brcm63xx/patches-3.6/406_bcm63xx_enet_vlan_incoming_fixed.patch deleted file mode 100644 index 7d9f4a96d1..0000000000 --- a/target/linux/brcm63xx/patches-3.6/406_bcm63xx_enet_vlan_incoming_fixed.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1515,7 +1515,7 @@ static int compute_hw_mtu(struct bcm_ene - actual_mtu = mtu; - - /* add ethernet header + vlan tag size */ -- actual_mtu += VLAN_ETH_HLEN; -+ actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN; - - if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU) - return -EINVAL; diff --git a/target/linux/brcm63xx/patches-3.6/408-6358-enet1-external-mii-clk.patch b/target/linux/brcm63xx/patches-3.6/408-6358-enet1-external-mii-clk.patch deleted file mode 100644 index 9ce7737fb2..0000000000 --- a/target/linux/brcm63xx/patches-3.6/408-6358-enet1-external-mii-clk.patch +++ /dev/null @@ -1,22 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -900,6 +900,8 @@ void __init board_prom_init(void) - if (BCMCPU_IS_6348()) - val |= GPIO_MODE_6348_G3_EXT_MII | - GPIO_MODE_6348_G0_EXT_MII; -+ else if (BCMCPU_IS_6358()) -+ val |= GPIO_MODE_6358_ENET1_MII_CLK_INV; - } - - bcm_gpio_writel(val, GPIO_MODE_REG); ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -563,6 +563,8 @@ - #define GPIO_MODE_6358_EXTRA_SPI_SS (1 << 7) - #define GPIO_MODE_6358_SERIAL_LED (1 << 10) - #define GPIO_MODE_6358_UTOPIA (1 << 12) -+#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 30) -+#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 31) - - #define GPIO_MODE_6368_ANALOG_AFE_0 (1 << 0) - #define GPIO_MODE_6368_ANALOG_AFE_1 (1 << 1) diff --git a/target/linux/brcm63xx/patches-3.6/410-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch b/target/linux/brcm63xx/patches-3.6/410-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch deleted file mode 100644 index 2102db35e8..0000000000 --- a/target/linux/brcm63xx/patches-3.6/410-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch +++ /dev/null @@ -1,169 +0,0 @@ -From b11218c750ab92cfab4408a0328f1b36ceec3f33 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Fri, 6 Jan 2012 12:24:18 +0100 -Subject: [PATCH 19/63] NET: bcm63xx_enet: move phy_(dis)connect into probe/remove - -Only connect/disconnect the phy during probe and remove, not during any -open/close. The phy seldom changes during the runtime, and disconnecting -the phy during close will prevent it from keeping any configuration over -a down/up cycle. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 84 +++++++++++++------------- - 1 files changed, 41 insertions(+), 43 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -784,10 +784,8 @@ static int bcm_enet_open(struct net_devi - struct bcm_enet_priv *priv; - struct sockaddr addr; - struct device *kdev; -- struct phy_device *phydev; - int i, ret; - unsigned int size; -- char phy_id[MII_BUS_ID_SIZE + 3]; - void *p; - u32 val; - -@@ -795,40 +793,10 @@ static int bcm_enet_open(struct net_devi - kdev = &priv->pdev->dev; - - if (priv->has_phy) { -- /* connect to PHY */ -- snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, -- priv->mii_bus->id, priv->phy_id); -- -- phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0, -- PHY_INTERFACE_MODE_MII); -- -- if (IS_ERR(phydev)) { -- dev_err(kdev, "could not attach to PHY\n"); -- return PTR_ERR(phydev); -- } -- -- /* mask with MAC supported features */ -- phydev->supported &= (SUPPORTED_10baseT_Half | -- SUPPORTED_10baseT_Full | -- SUPPORTED_100baseT_Half | -- SUPPORTED_100baseT_Full | -- SUPPORTED_Autoneg | -- SUPPORTED_Pause | -- SUPPORTED_MII); -- phydev->advertising = phydev->supported; -- -- if (priv->pause_auto && priv->pause_rx && priv->pause_tx) -- phydev->advertising |= SUPPORTED_Pause; -- else -- phydev->advertising &= ~SUPPORTED_Pause; -- -- dev_info(kdev, "attached PHY at address %d [%s]\n", -- phydev->addr, phydev->drv->name); -- -+ /* Reset state */ - priv->old_link = 0; - priv->old_duplex = -1; - priv->old_pause = -1; -- priv->phydev = phydev; - } - - /* mask all interrupts and request them */ -@@ -838,7 +806,7 @@ static int bcm_enet_open(struct net_devi - - ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); - if (ret) -- goto out_phy_disconnect; -+ return ret; - - ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, IRQF_DISABLED, - dev->name, dev); -@@ -1025,9 +993,6 @@ out_freeirq_rx: - out_freeirq: - free_irq(dev->irq, dev); - --out_phy_disconnect: -- phy_disconnect(priv->phydev); -- - return ret; - } - -@@ -1132,12 +1097,6 @@ static int bcm_enet_stop(struct net_devi - free_irq(priv->irq_rx, dev); - free_irq(dev->irq, dev); - -- /* release phy */ -- if (priv->has_phy) { -- phy_disconnect(priv->phydev); -- priv->phydev = NULL; -- } -- - return 0; - } - -@@ -1714,6 +1673,8 @@ static int __devinit bcm_enet_probe(stru - - /* MII bus registration */ - if (priv->has_phy) { -+ struct phy_device *phydev; -+ char phy_id[MII_BUS_ID_SIZE + 3]; - - priv->mii_bus = mdiobus_alloc(); - if (!priv->mii_bus) { -@@ -1750,6 +1711,38 @@ static int __devinit bcm_enet_probe(stru - dev_err(&pdev->dev, "unable to register mdio bus\n"); - goto out_free_mdio; - } -+ -+ /* connect to PHY */ -+ snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, -+ priv->mii_bus->id, priv->phy_id); -+ -+ phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0, -+ PHY_INTERFACE_MODE_MII); -+ -+ if (IS_ERR(phydev)) { -+ dev_err(&pdev->dev, "could not attach to PHY\n"); -+ goto out_unregister_mdio; -+ } -+ -+ /* mask with MAC supported features */ -+ phydev->supported &= (SUPPORTED_10baseT_Half | -+ SUPPORTED_10baseT_Full | -+ SUPPORTED_100baseT_Half | -+ SUPPORTED_100baseT_Full | -+ SUPPORTED_Autoneg | -+ SUPPORTED_Pause | -+ SUPPORTED_MII); -+ phydev->advertising = phydev->supported; -+ -+ if (priv->pause_auto && priv->pause_rx && priv->pause_tx) -+ phydev->advertising |= SUPPORTED_Pause; -+ else -+ phydev->advertising &= ~SUPPORTED_Pause; -+ -+ dev_info(&pdev->dev, "attached PHY at address %d [%s]\n", -+ phydev->addr, phydev->drv->name); -+ -+ priv->phydev = phydev; - } else { - - /* run platform code to initialize PHY device */ -@@ -1795,6 +1788,9 @@ static int __devinit bcm_enet_probe(stru - return 0; - - out_unregister_mdio: -+ if (priv->phydev) -+ phy_disconnect(priv->phydev); -+ - if (priv->mii_bus) { - mdiobus_unregister(priv->mii_bus); - kfree(priv->mii_bus->irq); -@@ -1845,6 +1841,8 @@ static int __devexit bcm_enet_remove(str - enet_writel(priv, 0, ENET_MIISC_REG); - - if (priv->has_phy) { -+ phy_disconnect(priv->phydev); -+ priv->phydev = NULL; - mdiobus_unregister(priv->mii_bus); - kfree(priv->mii_bus->irq); - mdiobus_free(priv->mii_bus); diff --git a/target/linux/brcm63xx/patches-3.6/411-bcm63xx_enet-implement-reset_autoneg-ethtool.patch b/target/linux/brcm63xx/patches-3.6/411-bcm63xx_enet-implement-reset_autoneg-ethtool.patch deleted file mode 100644 index d143b473d8..0000000000 --- a/target/linux/brcm63xx/patches-3.6/411-bcm63xx_enet-implement-reset_autoneg-ethtool.patch +++ /dev/null @@ -1,40 +0,0 @@ -From accc558f334662c8b16c121b4819931c028e8eb0 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Mon, 8 Jun 2009 16:12:10 +0200 -Subject: [PATCH 27/63] bcm63xx_enet: implement reset_autoneg ethtool. - ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 15 +++++++++++++++ - 1 files changed, 15 insertions(+), 0 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1290,6 +1290,20 @@ static void bcm_enet_get_ethtool_stats(s - mutex_unlock(&priv->mib_update_lock); - } - -+static int bcm_enet_nway_reset(struct net_device *dev) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ if (priv->has_phy) { -+ if (!priv->phydev) -+ return -ENODEV; -+ return genphy_restart_aneg(priv->phydev); -+ } -+ -+ return -EOPNOTSUPP; -+} -+ - static int bcm_enet_get_settings(struct net_device *dev, - struct ethtool_cmd *cmd) - { -@@ -1432,6 +1446,7 @@ static const struct ethtool_ops bcm_enet - .get_strings = bcm_enet_get_strings, - .get_sset_count = bcm_enet_get_sset_count, - .get_ethtool_stats = bcm_enet_get_ethtool_stats, -+ .nway_reset = bcm_enet_nway_reset, - .get_settings = bcm_enet_get_settings, - .set_settings = bcm_enet_set_settings, - .get_drvinfo = bcm_enet_get_drvinfo, diff --git a/target/linux/brcm63xx/patches-3.6/412-bcm63xx_enet-use-resource_size.patch b/target/linux/brcm63xx/patches-3.6/412-bcm63xx_enet-use-resource_size.patch deleted file mode 100644 index 11d035dd51..0000000000 --- a/target/linux/brcm63xx/patches-3.6/412-bcm63xx_enet-use-resource_size.patch +++ /dev/null @@ -1,69 +0,0 @@ -From dbd9b51204aa4114756b8659e180139ef3878032 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Thu, 21 Jan 2010 17:28:36 +0100 -Subject: [PATCH 28/63] bcm63xx_enet: use resource_size(). - ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 18 ++++++++---------- - 1 files changed, 8 insertions(+), 10 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1594,7 +1594,6 @@ static int __devinit bcm_enet_probe(stru - struct resource *res_mem, *res_irq, *res_irq_rx, *res_irq_tx; - struct mii_bus *bus; - const char *clk_name; -- unsigned int iomem_size; - int i, ret; - - /* stop if shared driver failed, assume driver->probe will be -@@ -1619,13 +1618,13 @@ static int __devinit bcm_enet_probe(stru - if (ret) - goto out; - -- iomem_size = resource_size(res_mem); -- if (!request_mem_region(res_mem->start, iomem_size, "bcm63xx_enet")) { -+ if (!request_mem_region(res_mem->start, resource_size(res_mem), -+ "bcm63xx_enet")) { - ret = -EBUSY; - goto out; - } - -- priv->base = ioremap(res_mem->start, iomem_size); -+ priv->base = ioremap(res_mem->start, resource_size(res_mem)); - if (priv->base == NULL) { - ret = -ENOMEM; - goto out_release_mem; -@@ -1831,7 +1830,7 @@ out_unmap: - iounmap(priv->base); - - out_release_mem: -- release_mem_region(res_mem->start, iomem_size); -+ release_mem_region(res_mem->start, resource_size(res_mem)); - out: - free_netdev(dev); - return ret; -@@ -1903,19 +1902,18 @@ struct platform_driver bcm63xx_enet_driv - static int __devinit bcm_enet_shared_probe(struct platform_device *pdev) - { - struct resource *res; -- unsigned int iomem_size; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) - return -ENODEV; - -- iomem_size = resource_size(res); -- if (!request_mem_region(res->start, iomem_size, "bcm63xx_enet_dma")) -+ if (!request_mem_region(res->start, resource_size(res), -+ "bcm63xx_enet_dma")) - return -EBUSY; - -- bcm_enet_shared_base = ioremap(res->start, iomem_size); -+ bcm_enet_shared_base = ioremap(res->start, resource_size(res)); - if (!bcm_enet_shared_base) { -- release_mem_region(res->start, iomem_size); -+ release_mem_region(res->start, resource_size(res)); - return -ENOMEM; - } - return 0; diff --git a/target/linux/brcm63xx/patches-3.6/413-bcm63xx_enet-disable-clock-when-uninitializing-devic.patch b/target/linux/brcm63xx/patches-3.6/413-bcm63xx_enet-disable-clock-when-uninitializing-devic.patch deleted file mode 100644 index a98bea9001..0000000000 --- a/target/linux/brcm63xx/patches-3.6/413-bcm63xx_enet-disable-clock-when-uninitializing-devic.patch +++ /dev/null @@ -1,20 +0,0 @@ -From fd15ecd10c95480be5635f8993b781fe3a1527c2 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Fri, 29 Apr 2011 16:54:50 +0200 -Subject: [PATCH 29/63] bcm63xx_enet: disable clock when uninitializing device. - ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 2 ++ - 1 files changed, 2 insertions(+), 0 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -1870,6 +1870,8 @@ static int __devexit bcm_enet_remove(str - } - - /* release device resources */ -+ clk_disable(priv->mac_clk); -+ clk_put(priv->mac_clk); - iounmap(priv->base); - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - release_mem_region(res->start, resource_size(res)); diff --git a/target/linux/brcm63xx/patches-3.6/414-bcm63xx_enet-split-dma-registers-access.patch b/target/linux/brcm63xx/patches-3.6/414-bcm63xx_enet-split-dma-registers-access.patch deleted file mode 100644 index 90999fa952..0000000000 --- a/target/linux/brcm63xx/patches-3.6/414-bcm63xx_enet-split-dma-registers-access.patch +++ /dev/null @@ -1,381 +0,0 @@ -From 305579c1f946ed1aa6c125252ace21c53d47c11d Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Thu, 21 Jan 2010 17:50:54 +0100 -Subject: [PATCH 30/63] bcm63xx_enet: split dma registers access. - ---- - arch/mips/bcm63xx/dev-enet.c | 23 +++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 4 +- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 179 ++++++++++++++-------- - 3 files changed, 138 insertions(+), 68 deletions(-) - ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -19,6 +19,16 @@ static struct resource shared_res[] = { - .end = -1, /* filled at runtime */ - .flags = IORESOURCE_MEM, - }, -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, - }; - - static struct platform_device bcm63xx_enet_shared_device = { -@@ -110,10 +120,15 @@ int __init bcm63xx_enet_register(int uni - if (!shared_device_registered) { - shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); - shared_res[0].end = shared_res[0].start; -- if (BCMCPU_IS_6338()) -- shared_res[0].end += (RSET_ENETDMA_SIZE / 2) - 1; -- else -- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ -+ shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC); -+ shared_res[1].end = shared_res[1].start; -+ shared_res[1].end += RSET_ENETDMAC_SIZE(16) - 1; -+ -+ shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS); -+ shared_res[2].end = shared_res[2].start; -+ shared_res[2].end += RSET_ENETDMAS_SIZE(16) - 1; - - ret = platform_device_register(&bcm63xx_enet_shared_device); - if (ret) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -172,7 +172,9 @@ enum bcm63xx_regs_set { - #define BCM_6358_RSET_SPI_SIZE 1804 - #define BCM_6368_RSET_SPI_SIZE 1804 - #define RSET_ENET_SIZE 2048 --#define RSET_ENETDMA_SIZE 2048 -+#define RSET_ENETDMA_SIZE 256 -+#define RSET_ENETDMAC_SIZE(chans) (16 * (chans)) -+#define RSET_ENETDMAS_SIZE(chans) (16 * (chans)) - #define RSET_ENETSW_SIZE 65536 - #define RSET_UART_SIZE 24 - #define RSET_HSSPI_SIZE 1536 ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -41,8 +41,8 @@ static int copybreak __read_mostly = 128 - module_param(copybreak, int, 0); - MODULE_PARM_DESC(copybreak, "Receive copy threshold"); - --/* io memory shared between all devices */ --static void __iomem *bcm_enet_shared_base; -+/* io registers memory shared between all devices */ -+static void __iomem *bcm_enet_shared_base[3]; - - /* - * io helpers to access mac registers -@@ -63,13 +63,35 @@ static inline void enet_writel(struct bc - */ - static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off) - { -- return bcm_readl(bcm_enet_shared_base + off); -+ return bcm_readl(bcm_enet_shared_base[0] + off); - } - - static inline void enet_dma_writel(struct bcm_enet_priv *priv, - u32 val, u32 off) - { -- bcm_writel(val, bcm_enet_shared_base + off); -+ bcm_writel(val, bcm_enet_shared_base[0] + off); -+} -+ -+static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off) -+{ -+ return bcm_readl(bcm_enet_shared_base[1] + off); -+} -+ -+static inline void enet_dmac_writel(struct bcm_enet_priv *priv, -+ u32 val, u32 off) -+{ -+ bcm_writel(val, bcm_enet_shared_base[1] + off); -+} -+ -+static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off) -+{ -+ return bcm_readl(bcm_enet_shared_base[2] + off); -+} -+ -+static inline void enet_dmas_writel(struct bcm_enet_priv *priv, -+ u32 val, u32 off) -+{ -+ bcm_writel(val, bcm_enet_shared_base[2] + off); - } - - /* -@@ -353,8 +375,8 @@ static int bcm_enet_receive_queue(struct - bcm_enet_refill_rx(dev); - - /* kick rx dma */ -- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, -- ENETDMA_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->rx_chan)); - } - - return processed; -@@ -429,10 +451,10 @@ static int bcm_enet_poll(struct napi_str - dev = priv->net_dev; - - /* ack interrupts */ -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->tx_chan)); - - /* reclaim sent skb */ - tx_work_done = bcm_enet_tx_reclaim(dev, 0); -@@ -451,10 +473,10 @@ static int bcm_enet_poll(struct napi_str - napi_complete(napi); - - /* restore rx/tx interrupt */ -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->tx_chan)); - - return rx_work_done; - } -@@ -497,8 +519,8 @@ static irqreturn_t bcm_enet_isr_dma(int - priv = netdev_priv(dev); - - /* mask rx/tx interrupts */ -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); - - napi_schedule(&priv->napi); - -@@ -557,8 +579,8 @@ static int bcm_enet_start_xmit(struct sk - wmb(); - - /* kick tx dma */ -- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, -- ENETDMA_CHANCFG_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->tx_chan)); - - /* stop queue if no more desc available */ - if (!priv->tx_desc_count) -@@ -801,8 +823,8 @@ static int bcm_enet_open(struct net_devi - - /* mask all interrupts and request them */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); - - ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); - if (ret) -@@ -891,28 +913,28 @@ static int bcm_enet_open(struct net_devi - } - - /* write rx & tx ring addresses */ -- enet_dma_writel(priv, priv->rx_desc_dma, -- ENETDMA_RSTART_REG(priv->rx_chan)); -- enet_dma_writel(priv, priv->tx_desc_dma, -- ENETDMA_RSTART_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, priv->rx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, priv->tx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->tx_chan)); - - /* clear remaining state ram for rx & tx channel */ -- enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->tx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->tx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); - - /* set max rx/tx length */ - enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG); - enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG); - - /* set dma maximum burst len */ -- enet_dma_writel(priv, BCMENET_DMA_MAXBURST, -- ENETDMA_MAXBURST_REG(priv->rx_chan)); -- enet_dma_writel(priv, BCMENET_DMA_MAXBURST, -- ENETDMA_MAXBURST_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ ENETDMAC_MAXBURST_REG(priv->tx_chan)); - - /* set correct transmit fifo watermark */ - enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG); -@@ -930,26 +952,26 @@ static int bcm_enet_open(struct net_devi - val |= ENET_CTL_ENABLE_MASK; - enet_writel(priv, val, ENET_CTL_REG); - enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); -- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, -- ENETDMA_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->rx_chan)); - - /* watch "mib counters about to overflow" interrupt */ - enet_writel(priv, ENET_IR_MIB, ENET_IR_REG); - enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG); - - /* watch "packet transferred" interrupt in rx and tx */ -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->tx_chan)); - - /* make sure we enable napi before rx interrupt */ - napi_enable(&priv->napi); - -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, -- ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->tx_chan)); - - if (priv->has_phy) - phy_start(priv->phydev); -@@ -1026,14 +1048,14 @@ static void bcm_enet_disable_dma(struct - { - int limit; - -- enet_dma_writel(priv, 0, ENETDMA_CHANCFG_REG(chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan)); - - limit = 1000; - do { - u32 val; - -- val = enet_dma_readl(priv, ENETDMA_CHANCFG_REG(chan)); -- if (!(val & ENETDMA_CHANCFG_EN_MASK)) -+ val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan)); -+ if (!(val & ENETDMAC_CHANCFG_EN_MASK)) - break; - udelay(1); - } while (limit--); -@@ -1059,8 +1081,8 @@ static int bcm_enet_stop(struct net_devi - - /* mask all interrupts */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); -- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); - - /* make sure no mib update is scheduled */ - cancel_work_sync(&priv->mib_update_task); -@@ -1598,7 +1620,7 @@ static int __devinit bcm_enet_probe(stru - - /* stop if shared driver failed, assume driver->probe will be - * called in the same order we register devices (correct ?) */ -- if (!bcm_enet_shared_base) -+ if (!bcm_enet_shared_base[0]) - return -ENODEV; - - res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -@@ -1904,30 +1926,61 @@ struct platform_driver bcm63xx_enet_driv - static int __devinit bcm_enet_shared_probe(struct platform_device *pdev) - { - struct resource *res; -+ int ret, i, requested[3]; - -- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -- if (!res) -- return -ENODEV; -+ memset(bcm_enet_shared_base, 0, sizeof (bcm_enet_shared_base)); -+ memset(requested, 0, sizeof (requested)); - -- if (!request_mem_region(res->start, resource_size(res), -- "bcm63xx_enet_dma")) -- return -EBUSY; -+ for (i = 0; i < 3; i++) { -+ void __iomem *p; - -- bcm_enet_shared_base = ioremap(res->start, resource_size(res)); -- if (!bcm_enet_shared_base) { -- release_mem_region(res->start, resource_size(res)); -- return -ENOMEM; -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ if (!res) { -+ ret = -EINVAL; -+ goto fail; -+ } -+ -+ if (!request_mem_region(res->start, resource_size(res), -+ "bcm63xx_enet_dma")) { -+ ret = -EBUSY; -+ goto fail; -+ } -+ requested[i] = 0; -+ -+ p = ioremap(res->start, resource_size(res)); -+ if (!p) { -+ ret = -ENOMEM; -+ goto fail; -+ } -+ -+ bcm_enet_shared_base[i] = p; - } -+ - return 0; -+ -+fail: -+ for (i = 0; i < 3; i++) { -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ if (!res) -+ continue; -+ if (bcm_enet_shared_base[i]) -+ iounmap(bcm_enet_shared_base[i]); -+ if (requested[i]) -+ release_mem_region(res->start, resource_size(res)); -+ } -+ return ret; - } - - static int __devexit bcm_enet_shared_remove(struct platform_device *pdev) - { - struct resource *res; -+ int i; - -- iounmap(bcm_enet_shared_base); -- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -- release_mem_region(res->start, resource_size(res)); -+ for (i = 0; i < 3; i++) { -+ iounmap(bcm_enet_shared_base[i]); -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ release_mem_region(res->start, resource_size(res)); -+ } - return 0; - } - diff --git a/target/linux/brcm63xx/patches-3.6/415-bcm63xx_enet-add-support-for-bcm6368-internal-ethern.patch b/target/linux/brcm63xx/patches-3.6/415-bcm63xx_enet-add-support-for-bcm6368-internal-ethern.patch deleted file mode 100644 index 5c1cf05f58..0000000000 --- a/target/linux/brcm63xx/patches-3.6/415-bcm63xx_enet-add-support-for-bcm6368-internal-ethern.patch +++ /dev/null @@ -1,1490 +0,0 @@ -From 1324bb5db6815d19b09c1b7bcac3cc2804412205 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Sat, 23 Jan 2010 03:01:02 +0100 -Subject: [PATCH 31/63] bcm63xx_enet: add support for bcm6368 internal ethernet switch. - ---- - arch/mips/bcm63xx/dev-enet.c | 106 ++- - .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 25 + - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 50 + - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 1054 ++++++++++++++++++-- - drivers/net/ethernet/broadcom/bcm63xx_enet.h | 71 ++ - 5 files changed, 1221 insertions(+), 85 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -965,6 +965,10 @@ int __init board_register_devices(void) - !board_get_mac_address(board.enet1.mac_addr)) - bcm63xx_enet_register(1, &board.enet1); - -+ if (board.has_enetsw && -+ !board_get_mac_address(board.enetsw.mac_addr)) -+ bcm63xx_enetsw_register(&board.enetsw); -+ - if (board.has_ehci0) - bcm63xx_ehci_register(); - ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -41,6 +41,7 @@ struct board_info { - /* enabled feature/device */ - unsigned int has_enet0:1; - unsigned int has_enet1:1; -+ unsigned int has_enetsw:1; - unsigned int has_pci:1; - unsigned int has_pccard:1; - unsigned int has_ohci0:1; -@@ -52,6 +53,7 @@ struct board_info { - /* ethernet config */ - struct bcm63xx_enet_platform_data enet0; - struct bcm63xx_enet_platform_data enet1; -+ struct bcm63xx_enetsw_platform_data enetsw; - - /* DSP config */ - struct bcm63xx_dsp_platform_data dsp; ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -104,6 +104,64 @@ static struct platform_device bcm63xx_en - }, - }; - -+static struct resource enetsw_res[] = { -+ { -+ /* start & end filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ /* start filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+ { -+ /* start filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct bcm63xx_enetsw_platform_data enetsw_pd; -+ -+static struct platform_device bcm63xx_enetsw_device = { -+ .name = "bcm63xx_enetsw", -+ .num_resources = ARRAY_SIZE(enetsw_res), -+ .resource = enetsw_res, -+ .dev = { -+ .platform_data = &enetsw_pd, -+ }, -+}; -+ -+static int __init register_shared(void) -+{ -+ int ret, chan_count; -+ -+ if (shared_device_registered) -+ return 0; -+ -+ shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); -+ shared_res[0].end = shared_res[0].start; -+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ -+ if (BCMCPU_IS_6368()) -+ chan_count = 32; -+ else -+ chan_count = 16; -+ -+ shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC); -+ shared_res[1].end = shared_res[1].start; -+ shared_res[1].end += RSET_ENETDMAC_SIZE(chan_count) - 1; -+ -+ shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS); -+ shared_res[2].end = shared_res[2].start; -+ shared_res[2].end += RSET_ENETDMAS_SIZE(chan_count) - 1; -+ -+ ret = platform_device_register(&bcm63xx_enet_shared_device); -+ if (ret) -+ return ret; -+ shared_device_registered = 1; -+ -+ return 0; -+} -+ - int __init bcm63xx_enet_register(int unit, - const struct bcm63xx_enet_platform_data *pd) - { -@@ -117,24 +175,9 @@ int __init bcm63xx_enet_register(int uni - if (unit == 1 && BCMCPU_IS_6338()) - return -ENODEV; - -- if (!shared_device_registered) { -- shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); -- shared_res[0].end = shared_res[0].start; -- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -- -- shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC); -- shared_res[1].end = shared_res[1].start; -- shared_res[1].end += RSET_ENETDMAC_SIZE(16) - 1; -- -- shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS); -- shared_res[2].end = shared_res[2].start; -- shared_res[2].end += RSET_ENETDMAS_SIZE(16) - 1; -- -- ret = platform_device_register(&bcm63xx_enet_shared_device); -- if (ret) -- return ret; -- shared_device_registered = 1; -- } -+ ret = register_shared(); -+ if (ret) -+ return ret; - - if (unit == 0) { - enet0_res[0].start = bcm63xx_regset_address(RSET_ENET0); -@@ -175,3 +218,30 @@ int __init bcm63xx_enet_register(int uni - return ret; - return 0; - } -+ -+int __init -+bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd) -+{ -+ int ret; -+ -+ if (!BCMCPU_IS_6368()) -+ return -ENODEV; -+ -+ ret = register_shared(); -+ if (ret) -+ return ret; -+ -+ enetsw_res[0].start = bcm63xx_regset_address(RSET_ENETSW); -+ enetsw_res[0].end = enetsw_res[0].start; -+ enetsw_res[0].end += RSET_ENETSW_SIZE - 1; -+ enetsw_res[1].start = bcm63xx_get_irq_number(IRQ_ENETSW_RXDMA0); -+ enetsw_res[2].start = bcm63xx_get_irq_number(IRQ_ENETSW_TXDMA0); -+ -+ memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof (*pd)); -+ -+ ret = platform_device_register(&bcm63xx_enetsw_device); -+ if (ret) -+ return ret; -+ -+ return 0; -+} ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -39,7 +39,32 @@ struct bcm63xx_enet_platform_data { - int phy_id, int reg, int val)); - }; - -+/* -+ * on board ethernet switch platform data -+ */ -+#define ENETSW_MAX_PORT 6 -+ -+struct bcm63xx_enetsw_port { -+ int used; -+ int external_phy; -+ int phy_id; -+ -+ int bypass_link; -+ int force_speed; -+ int force_duplex_full; -+ -+ const char *name; -+}; -+ -+struct bcm63xx_enetsw_platform_data { -+ char mac_addr[ETH_ALEN]; -+ struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; -+}; -+ - int __init bcm63xx_enet_register(int unit, - const struct bcm63xx_enet_platform_data *pd); - -+int __init -+bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd); -+ - #endif /* ! BCM63XX_DEV_ENET_H_ */ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -809,10 +809,60 @@ - * _REG relative to RSET_ENETSW - *************************************************************************/ - -+/* Port traffic control */ -+#define ENETSW_PTCTRL_REG(x) (0x0 + (x)) -+#define ENETSW_PTCTRL_RXDIS_MASK (1 << 0) -+#define ENETSW_PTCTRL_TXDIS_MASK (1 << 1) -+ -+/* Switch mode register */ -+#define ENETSW_SWMODE_REG (0xb) -+#define ENETSW_SWMODE_FWD_EN_MASK (1 << 1) -+ -+/* IMP override Register */ -+#define ENETSW_IMPOV_REG (0xe) -+#define ENETSW_IMPOV_FORCE_MASK (1 << 7) -+#define ENETSW_IMPOV_TXFLOW_MASK (1 << 5) -+#define ENETSW_IMPOV_RXFLOW_MASK (1 << 4) -+#define ENETSW_IMPOV_1000_MASK (1 << 3) -+#define ENETSW_IMPOV_100_MASK (1 << 2) -+#define ENETSW_IMPOV_FDX_MASK (1 << 1) -+#define ENETSW_IMPOV_LINKUP_MASK (1 << 0) -+ -+/* Port override Register */ -+#define ENETSW_PORTOV_REG(x) (0x58 + (x)) -+#define ENETSW_PORTOV_ENABLE_MASK (1 << 6) -+#define ENETSW_PORTOV_TXFLOW_MASK (1 << 5) -+#define ENETSW_PORTOV_RXFLOW_MASK (1 << 4) -+#define ENETSW_PORTOV_1000_MASK (1 << 3) -+#define ENETSW_PORTOV_100_MASK (1 << 2) -+#define ENETSW_PORTOV_FDX_MASK (1 << 1) -+#define ENETSW_PORTOV_LINKUP_MASK (1 << 0) -+ -+/* MDIO control register */ -+#define ENETSW_MDIOC_REG (0xb0) -+#define ENETSW_MDIOC_EXT_MASK (1 << 16) -+#define ENETSW_MDIOC_REG_SHIFT 20 -+#define ENETSW_MDIOC_PHYID_SHIFT 25 -+#define ENETSW_MDIOC_RD_MASK (1 << 30) -+#define ENETSW_MDIOC_WR_MASK (1 << 31) -+ -+/* MDIO data register */ -+#define ENETSW_MDIOD_REG (0xb4) -+ -+/* Global Management Configuration Register */ -+#define ENETSW_GMCR_REG (0x200) -+#define ENETSW_GMCR_RST_MIB_MASK (1 << 0) -+ - /* MIB register */ - #define ENETSW_MIB_REG(x) (0x2800 + (x) * 4) - #define ENETSW_MIB_REG_COUNT 47 - -+/* Jumbo control register port mask register */ -+#define ENETSW_JMBCTL_PORT_REG (0x4004) -+ -+/* Jumbo control mib good frame register */ -+#define ENETSW_JMBCTL_MAXSIZE_REG (0x4008) -+ - - /************************************************************************* - * _REG relative to RSET_OHCI_PRIV ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -59,6 +59,49 @@ static inline void enet_writel(struct bc - } - - /* -+ * io helpers to access switch registers -+ */ -+static inline u32 enetsw_readl(struct bcm_enet_priv *priv, u32 off) -+{ -+ /* printk("enetsw_readl at %p\n", priv->base + off); */ -+ return bcm_readl(priv->base + off); -+} -+ -+static inline void enetsw_writel(struct bcm_enet_priv *priv, -+ u32 val, u32 off) -+{ -+ /* printk("enetsw_writel %08x at %p\n", val, priv->base + off); */ -+ bcm_writel(val, priv->base + off); -+} -+ -+static inline u16 enetsw_readw(struct bcm_enet_priv *priv, u32 off) -+{ -+ /* printk("enetsw_readw at %p\n", priv->base + off); */ -+ return bcm_readw(priv->base + off); -+} -+ -+static inline void enetsw_writew(struct bcm_enet_priv *priv, -+ u16 val, u32 off) -+{ -+ /* printk("enetsw_writew %04x at %p\n", val, priv->base + off); */ -+ bcm_writew(val, priv->base + off); -+} -+ -+static inline u8 enetsw_readb(struct bcm_enet_priv *priv, u32 off) -+{ -+ /* printk("enetsw_readb at %p\n", priv->base + off); */ -+ return bcm_readb(priv->base + off); -+} -+ -+static inline void enetsw_writeb(struct bcm_enet_priv *priv, -+ u8 val, u32 off) -+{ -+ /* printk("enetsw_writeb %02x at %p\n", val, priv->base + off); */ -+ bcm_writeb(val, priv->base + off); -+} -+ -+ -+/* - * io helpers to access shared registers - */ - static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off) -@@ -321,7 +364,8 @@ static int bcm_enet_receive_queue(struct - } - - /* recycle packet if it's marked as bad */ -- if (unlikely(len_stat & DMADESC_ERR_MASK)) { -+ if (!bcm_enet_is_sw(priv) && -+ unlikely(len_stat & DMADESC_ERR_MASK)) { - dev->stats.rx_errors++; - - if (len_stat & DMADESC_OVSIZE_MASK) -@@ -552,6 +596,26 @@ static int bcm_enet_start_xmit(struct sk - goto out_unlock; - } - -+ /* pad small packets sent on a switch device */ -+ if (bcm_enet_is_sw(priv) && skb->len < 64) { -+ int needed = 64 - skb->len; -+ char *data; -+ -+ if (unlikely(skb_tailroom(skb) < needed)) { -+ struct sk_buff *nskb; -+ -+ nskb = skb_copy_expand(skb, 0, needed, GFP_ATOMIC); -+ if (!nskb) { -+ ret = NETDEV_TX_BUSY; -+ goto out_unlock; -+ } -+ dev_kfree_skb(skb); -+ skb = nskb; -+ } -+ data = skb_put(skb, needed); -+ memset(data, 0, needed); -+ } -+ - /* point to the next available desc */ - desc = &priv->tx_desc_cpu[priv->tx_curr_desc]; - priv->tx_skb[priv->tx_curr_desc] = skb; -@@ -1921,96 +1985,951 @@ struct platform_driver bcm63xx_enet_driv - }; - - /* -- * reserve & remap memory space shared between all macs -+ * switch mii access callbacks - */ --static int __devinit bcm_enet_shared_probe(struct platform_device *pdev) -+static int bcmenet_sw_mdio_read(struct bcm_enet_priv *priv, -+ int ext, int phy_id, int location) - { -- struct resource *res; -- int ret, i, requested[3]; -+ u32 reg; -+ int ret; - -- memset(bcm_enet_shared_base, 0, sizeof (bcm_enet_shared_base)); -- memset(requested, 0, sizeof (requested)); -+ spin_lock_bh(&priv->enetsw_mdio_lock); -+ enetsw_writel(priv, 0, ENETSW_MDIOC_REG); - -- for (i = 0; i < 3; i++) { -- void __iomem *p; -+ reg = ENETSW_MDIOC_RD_MASK | -+ (phy_id << ENETSW_MDIOC_PHYID_SHIFT) | -+ (location << ENETSW_MDIOC_REG_SHIFT); -+ -+ if (ext) -+ reg |= ENETSW_MDIOC_EXT_MASK; -+ -+ enetsw_writel(priv, reg, ENETSW_MDIOC_REG); -+ udelay(50); -+ ret = enetsw_readw(priv, ENETSW_MDIOD_REG); -+ spin_unlock_bh(&priv->enetsw_mdio_lock); -+ return ret; -+} - -- res = platform_get_resource(pdev, IORESOURCE_MEM, i); -- if (!res) { -- ret = -EINVAL; -- goto fail; -- } -+static void bcmenet_sw_mdio_write(struct bcm_enet_priv *priv, -+ int ext, int phy_id, int location, -+ uint16_t data) -+{ -+ u32 reg; - -- if (!request_mem_region(res->start, resource_size(res), -- "bcm63xx_enet_dma")) { -- ret = -EBUSY; -- goto fail; -- } -- requested[i] = 0; -+ spin_lock_bh(&priv->enetsw_mdio_lock); -+ enetsw_writel(priv, 0, ENETSW_MDIOC_REG); - -- p = ioremap(res->start, resource_size(res)); -- if (!p) { -- ret = -ENOMEM; -- goto fail; -- } -+ reg = ENETSW_MDIOC_WR_MASK | -+ (phy_id << ENETSW_MDIOC_PHYID_SHIFT) | -+ (location << ENETSW_MDIOC_REG_SHIFT); - -- bcm_enet_shared_base[i] = p; -- } -+ if (ext) -+ reg |= ENETSW_MDIOC_EXT_MASK; - -- return 0; -+ reg |= data; - --fail: -- for (i = 0; i < 3; i++) { -- res = platform_get_resource(pdev, IORESOURCE_MEM, i); -- if (!res) -- continue; -- if (bcm_enet_shared_base[i]) -- iounmap(bcm_enet_shared_base[i]); -- if (requested[i]) -- release_mem_region(res->start, resource_size(res)); -- } -- return ret; -+ enetsw_writel(priv, reg, ENETSW_MDIOC_REG); -+ udelay(50); -+ spin_unlock_bh(&priv->enetsw_mdio_lock); - } - --static int __devexit bcm_enet_shared_remove(struct platform_device *pdev) -+/* -+ * enet sw PHY polling -+ */ -+static void swphy_poll_timer(unsigned long data) - { -- struct resource *res; -- int i; -+ struct bcm_enet_priv *priv = (struct bcm_enet_priv *)data; -+ unsigned int i; - -- for (i = 0; i < 3; i++) { -- iounmap(bcm_enet_shared_base[i]); -- res = platform_get_resource(pdev, IORESOURCE_MEM, i); -- release_mem_region(res->start, resource_size(res)); -+ for (i = 0; i < ARRAY_SIZE(priv->used_ports); i++) { -+ struct bcm63xx_enetsw_port *port; -+ int val, j, up, advertise, lpa, lpa2, speed, duplex, media; -+ u8 override; -+ -+ port = &priv->used_ports[i]; -+ if (!port->used) -+ continue; -+ -+ if (port->bypass_link) -+ continue; -+ -+ /* dummy read to clear */ -+ for (j = 0; j < 2; j++) -+ val = bcmenet_sw_mdio_read(priv, port->external_phy, -+ port->phy_id, MII_BMSR); -+ -+ if (val == 0xffff) -+ continue; -+ -+ up = (val & BMSR_LSTATUS) ? 1 : 0; -+ if (!(up ^ priv->sw_port_link[i])) -+ continue; -+ -+ priv->sw_port_link[i] = up; -+ -+ /* link changed */ -+ if (!up) { -+ dev_info(&priv->pdev->dev, "link DOWN on %s\n", -+ port->name); -+ enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK, -+ ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK | -+ ENETSW_PTCTRL_TXDIS_MASK, -+ ENETSW_PTCTRL_REG(i)); -+ continue; -+ } -+ -+ advertise = bcmenet_sw_mdio_read(priv, port->external_phy, -+ port->phy_id, MII_ADVERTISE); -+ -+ lpa = bcmenet_sw_mdio_read(priv, port->external_phy, -+ port->phy_id, MII_LPA); -+ -+ lpa2 = bcmenet_sw_mdio_read(priv, port->external_phy, -+ port->phy_id, MII_STAT1000); -+ -+ /* figure out media and duplex from advertise and LPA values */ -+ media = mii_nway_result(lpa & advertise); -+ duplex = (media & ADVERTISE_FULL) ? 1 : 0; -+ if (lpa2 & LPA_1000FULL) -+ duplex = 1; -+ -+ if (lpa2 & (LPA_1000FULL | LPA_1000HALF)) -+ speed = 1000; -+ else { -+ if (media & (ADVERTISE_100FULL | ADVERTISE_100HALF)) -+ speed = 100; -+ else -+ speed = 10; -+ } -+ -+ dev_info(&priv->pdev->dev, -+ "link UP on %s, %dMbps, %s-duplex\n", -+ port->name, speed, duplex ? "full" : "half"); -+ -+ override = ENETSW_PORTOV_ENABLE_MASK | -+ ENETSW_PORTOV_LINKUP_MASK; -+ -+ if (speed == 1000) -+ override |= ENETSW_IMPOV_1000_MASK; -+ else if (speed == 100) -+ override |= ENETSW_IMPOV_100_MASK; -+ if (duplex) -+ override |= ENETSW_IMPOV_FDX_MASK; -+ -+ enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, 0, ENETSW_PTCTRL_REG(i)); - } -- return 0; --} - --/* -- * this "shared" driver is needed because both macs share a single -- * address space -- */ --struct platform_driver bcm63xx_enet_shared_driver = { -- .probe = bcm_enet_shared_probe, -- .remove = __devexit_p(bcm_enet_shared_remove), -- .driver = { -- .name = "bcm63xx_enet_shared", -- .owner = THIS_MODULE, -- }, --}; -+ priv->swphy_poll.expires = jiffies + HZ; -+ add_timer(&priv->swphy_poll); -+} - - /* -- * entry point -+ * open callback, allocate dma rings & buffers and start rx operation - */ --static int __init bcm_enet_init(void) -+static int bcm_enetsw_open(struct net_device *dev) - { -- int ret; -+ struct bcm_enet_priv *priv; -+ struct device *kdev; -+ int i, ret; -+ unsigned int size; -+ void *p; -+ u32 val; - -- ret = platform_driver_register(&bcm63xx_enet_shared_driver); -+ priv = netdev_priv(dev); -+ kdev = &priv->pdev->dev; -+ -+ /* mask all interrupts and request them */ -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ -+ ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, -+ IRQF_DISABLED, dev->name, dev); - if (ret) -- return ret; -+ goto out_freeirq; - -- ret = platform_driver_register(&bcm63xx_enet_driver); -+ ret = request_irq(priv->irq_tx, bcm_enet_isr_dma, -+ IRQF_DISABLED, dev->name, dev); - if (ret) -- platform_driver_unregister(&bcm63xx_enet_shared_driver); -+ goto out_freeirq_rx; -+ -+ /* allocate rx dma ring */ -+ size = priv->rx_ring_size * sizeof(struct bcm_enet_desc); -+ p = dma_alloc_coherent(kdev, size, &priv->rx_desc_dma, GFP_KERNEL); -+ if (!p) { -+ dev_err(kdev, "cannot allocate rx ring %u\n", size); -+ ret = -ENOMEM; -+ goto out_freeirq_tx; -+ } -+ -+ memset(p, 0, size); -+ priv->rx_desc_alloc_size = size; -+ priv->rx_desc_cpu = p; -+ -+ /* allocate tx dma ring */ -+ size = priv->tx_ring_size * sizeof(struct bcm_enet_desc); -+ p = dma_alloc_coherent(kdev, size, &priv->tx_desc_dma, GFP_KERNEL); -+ if (!p) { -+ dev_err(kdev, "cannot allocate tx ring\n"); -+ ret = -ENOMEM; -+ goto out_free_rx_ring; -+ } -+ -+ memset(p, 0, size); -+ priv->tx_desc_alloc_size = size; -+ priv->tx_desc_cpu = p; -+ -+ priv->tx_skb = kzalloc(sizeof(struct sk_buff *) * priv->tx_ring_size, -+ GFP_KERNEL); -+ if (!priv->tx_skb) { -+ dev_err(kdev, "cannot allocate rx skb queue\n"); -+ ret = -ENOMEM; -+ goto out_free_tx_ring; -+ } -+ -+ priv->tx_desc_count = priv->tx_ring_size; -+ priv->tx_dirty_desc = 0; -+ priv->tx_curr_desc = 0; -+ spin_lock_init(&priv->tx_lock); -+ -+ /* init & fill rx ring with skbs */ -+ priv->rx_skb = kzalloc(sizeof(struct sk_buff *) * priv->rx_ring_size, -+ GFP_KERNEL); -+ if (!priv->rx_skb) { -+ dev_err(kdev, "cannot allocate rx skb queue\n"); -+ ret = -ENOMEM; -+ goto out_free_tx_skb; -+ } -+ -+ priv->rx_desc_count = 0; -+ priv->rx_dirty_desc = 0; -+ priv->rx_curr_desc = 0; -+ -+ /* disable all ports */ -+ for (i = 0; i < 6; i++) { -+ enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK, -+ ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK | -+ ENETSW_PTCTRL_TXDIS_MASK, -+ ENETSW_PTCTRL_REG(i)); -+ } -+ -+ /* reset mib */ -+ val = enetsw_readb(priv, ENETSW_GMCR_REG); -+ val |= ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ val &= ~ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ -+ /* force CPU port state */ -+ val = enetsw_readb(priv, ENETSW_IMPOV_REG); -+ val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; -+ enetsw_writeb(priv, val, ENETSW_IMPOV_REG); -+ -+ /* enable switch forward engine */ -+ val = enetsw_readb(priv, ENETSW_SWMODE_REG); -+ val |= ENETSW_SWMODE_FWD_EN_MASK; -+ enetsw_writeb(priv, val, ENETSW_SWMODE_REG); -+ -+ /* enable jumbo on all ports */ -+ enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); -+ enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); -+ -+ /* initialize flow control buffer allocation */ -+ enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -+ ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ -+ if (bcm_enet_refill_rx(dev)) { -+ dev_err(kdev, "cannot allocate rx skb queue\n"); -+ ret = -ENOMEM; -+ goto out; -+ } -+ -+ /* write rx & tx ring addresses */ -+ enet_dmas_writel(priv, priv->rx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, priv->tx_desc_dma, -+ ENETDMAS_RSTART_REG(priv->tx_chan)); -+ -+ /* clear remaining state ram for rx & tx channel */ -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); -+ -+ /* set dma maximum burst len */ -+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ ENETDMAC_MAXBURST_REG(priv->tx_chan)); -+ -+ /* set flow control low/high threshold to 1/3 / 2/3 */ -+ val = priv->rx_ring_size / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan)); -+ val = (priv->rx_ring_size * 2) / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan)); -+ -+ /* all set, enable mac and interrupts, start dma engine and -+ * kick rx dma channel */ -+ wmb(); -+ enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); -+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -+ ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ -+ /* watch "packet transferred" interrupt in rx and tx */ -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IR_REG(priv->tx_chan)); -+ -+ /* make sure we enable napi before rx interrupt */ -+ napi_enable(&priv->napi); -+ -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -+ ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ -+ netif_carrier_on(dev); -+ netif_start_queue(dev); -+ -+ /* -+ * apply override config for bypass_link ports here. -+ */ -+ for (i = 0; i < ARRAY_SIZE(priv->used_ports); i++) { -+ struct bcm63xx_enetsw_port *port; -+ u8 override; -+ port = &priv->used_ports[i]; -+ if (!port->used) -+ continue; -+ -+ if (!port->bypass_link) -+ continue; -+ -+ override = ENETSW_PORTOV_ENABLE_MASK | -+ ENETSW_PORTOV_LINKUP_MASK; -+ -+ switch (port->force_speed) { -+ case 1000: -+ override |= ENETSW_IMPOV_1000_MASK; -+ break; -+ case 100: -+ override |= ENETSW_IMPOV_100_MASK; -+ break; -+ case 10: -+ break; -+ default: -+ printk(KERN_WARNING "invalid forced speed on port %s: " -+ "assume 10\n", -+ port->name); -+ break; -+ } -+ -+ if (port->force_duplex_full) -+ override = ENETSW_IMPOV_FDX_MASK; -+ -+ -+ enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i)); -+ enetsw_writeb(priv, 0, ENETSW_PTCTRL_REG(i)); -+ } -+ -+ /* start phy polling timer */ -+ init_timer(&priv->swphy_poll); -+ priv->swphy_poll.function = swphy_poll_timer; -+ priv->swphy_poll.data = (unsigned long)priv; -+ priv->swphy_poll.expires = jiffies; -+ add_timer(&priv->swphy_poll); -+ return 0; -+ -+out: -+ for (i = 0; i < priv->rx_ring_size; i++) { -+ struct bcm_enet_desc *desc; -+ -+ if (!priv->rx_skb[i]) -+ continue; -+ -+ desc = &priv->rx_desc_cpu[i]; -+ dma_unmap_single(kdev, desc->address, priv->rx_skb_size, -+ DMA_FROM_DEVICE); -+ kfree_skb(priv->rx_skb[i]); -+ } -+ kfree(priv->rx_skb); -+ -+out_free_tx_skb: -+ kfree(priv->tx_skb); -+ -+out_free_tx_ring: -+ dma_free_coherent(kdev, priv->tx_desc_alloc_size, -+ priv->tx_desc_cpu, priv->tx_desc_dma); -+ -+out_free_rx_ring: -+ dma_free_coherent(kdev, priv->rx_desc_alloc_size, -+ priv->rx_desc_cpu, priv->rx_desc_dma); -+ -+out_freeirq_tx: -+ free_irq(priv->irq_tx, dev); -+ -+out_freeirq_rx: -+ free_irq(priv->irq_rx, dev); -+ -+out_freeirq: -+ return ret; -+} -+ -+/* -+ * stop callback -+ */ -+static int bcm_enetsw_stop(struct net_device *dev) -+{ -+ struct bcm_enet_priv *priv; -+ struct device *kdev; -+ int i; -+ -+ priv = netdev_priv(dev); -+ kdev = &priv->pdev->dev; -+ -+ del_timer_sync(&priv->swphy_poll); -+ netif_stop_queue(dev); -+ napi_disable(&priv->napi); -+ del_timer_sync(&priv->rx_timeout); -+ -+ /* mask all interrupts */ -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ -+ /* disable dma & mac */ -+ bcm_enet_disable_dma(priv, priv->tx_chan); -+ bcm_enet_disable_dma(priv, priv->rx_chan); -+ -+ /* force reclaim of all tx buffers */ -+ bcm_enet_tx_reclaim(dev, 1); -+ -+ /* free the rx skb ring */ -+ for (i = 0; i < priv->rx_ring_size; i++) { -+ struct bcm_enet_desc *desc; -+ -+ if (!priv->rx_skb[i]) -+ continue; -+ -+ desc = &priv->rx_desc_cpu[i]; -+ dma_unmap_single(kdev, desc->address, priv->rx_skb_size, -+ DMA_FROM_DEVICE); -+ kfree_skb(priv->rx_skb[i]); -+ } -+ -+ /* free remaining allocated memory */ -+ kfree(priv->rx_skb); -+ kfree(priv->tx_skb); -+ dma_free_coherent(kdev, priv->rx_desc_alloc_size, -+ priv->rx_desc_cpu, priv->rx_desc_dma); -+ dma_free_coherent(kdev, priv->tx_desc_alloc_size, -+ priv->tx_desc_cpu, priv->tx_desc_dma); -+ free_irq(priv->irq_tx, dev); -+ free_irq(priv->irq_rx, dev); -+ -+ return 0; -+} -+ -+/* -+ * try to sort out phy external status by walking the used_port field -+ * in the bcm_enet_priv structure. in case the phy address is not -+ * assigned to any physical port on the switch, assume it is external -+ * (and yell at the user). -+ */ -+static int bcm_enetsw_phy_is_external(struct bcm_enet_priv *priv, int phy_id) -+{ -+ int i; -+ -+ for (i = 0; i < (int)ARRAY_SIZE(priv->used_ports); ++i) { -+ if (!priv->used_ports[i].used) -+ continue; -+ if (priv->used_ports[i].phy_id == phy_id) -+ return priv->used_ports[i].external_phy; -+ } -+ -+ printk_once(KERN_WARNING "bcm63xx_enet: could not find a used port " -+ "with phy_id %i, assuming phy is external\n", phy_id); -+ return 1; -+} -+ -+/* -+ * can't use bcmenet_sw_mdio_read directly as we need to sort out -+ * external/internal status of the given phy_id first. -+ */ -+static int bcm_enetsw_mii_mdio_read(struct net_device *dev, int phy_id, -+ int location) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ return bcmenet_sw_mdio_read(priv, -+ bcm_enetsw_phy_is_external(priv, phy_id), -+ phy_id, location); -+} -+ -+/* -+ * can't use bcmenet_sw_mdio_write directly as we need to sort out -+ * external/internal status of the given phy_id first. -+ */ -+static void bcm_enetsw_mii_mdio_write(struct net_device *dev, int phy_id, -+ int location, -+ int val) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ bcmenet_sw_mdio_write(priv, bcm_enetsw_phy_is_external(priv, phy_id), -+ phy_id, location, val); -+} -+ -+static int bcm_enetsw_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) -+{ -+ struct mii_if_info mii; -+ -+ mii.dev = dev; -+ mii.mdio_read = bcm_enetsw_mii_mdio_read; -+ mii.mdio_write = bcm_enetsw_mii_mdio_write; -+ mii.phy_id = 0; -+ mii.phy_id_mask = 0x3f; -+ mii.reg_num_mask = 0x1f; -+ return generic_mii_ioctl(&mii, if_mii(rq), cmd, NULL); -+ -+} -+ -+static const struct net_device_ops bcm_enetsw_ops = { -+ .ndo_open = bcm_enetsw_open, -+ .ndo_stop = bcm_enetsw_stop, -+ .ndo_start_xmit = bcm_enet_start_xmit, -+ .ndo_change_mtu = bcm_enet_change_mtu, -+ .ndo_do_ioctl = bcm_enetsw_ioctl, -+}; -+ -+ -+static const struct bcm_enet_stats bcm_enetsw_gstrings_stats[] = { -+ { "rx_packets", DEV_STAT(rx_packets), -1 }, -+ { "tx_packets", DEV_STAT(tx_packets), -1 }, -+ { "rx_bytes", DEV_STAT(rx_bytes), -1 }, -+ { "tx_bytes", DEV_STAT(tx_bytes), -1 }, -+ { "rx_errors", DEV_STAT(rx_errors), -1 }, -+ { "tx_errors", DEV_STAT(tx_errors), -1 }, -+ { "rx_dropped", DEV_STAT(rx_dropped), -1 }, -+ { "tx_dropped", DEV_STAT(tx_dropped), -1 }, -+ -+ { "tx_good_octets", GEN_STAT(mib.tx_gd_octets), ETHSW_MIB_RX_GD_OCT }, -+ { "tx_unicast", GEN_STAT(mib.tx_unicast), ETHSW_MIB_RX_BRDCAST }, -+ { "tx_broadcast", GEN_STAT(mib.tx_brdcast), ETHSW_MIB_RX_BRDCAST }, -+ { "tx_multicast", GEN_STAT(mib.tx_mult), ETHSW_MIB_RX_MULT }, -+ { "tx_64_octets", GEN_STAT(mib.tx_64), ETHSW_MIB_RX_64 }, -+ { "tx_65_127_oct", GEN_STAT(mib.tx_65_127), ETHSW_MIB_RX_65_127 }, -+ { "tx_128_255_oct", GEN_STAT(mib.tx_128_255), ETHSW_MIB_RX_128_255 }, -+ { "tx_256_511_oct", GEN_STAT(mib.tx_256_511), ETHSW_MIB_RX_256_511 }, -+ { "tx_512_1023_oct", GEN_STAT(mib.tx_512_1023), ETHSW_MIB_RX_512_1023}, -+ { "tx_1024_1522_oct", GEN_STAT(mib.tx_1024_max), -+ ETHSW_MIB_RX_1024_1522 }, -+ { "tx_1523_2047_oct", GEN_STAT(mib.tx_1523_2047), -+ ETHSW_MIB_RX_1523_2047 }, -+ { "tx_2048_4095_oct", GEN_STAT(mib.tx_2048_4095), -+ ETHSW_MIB_RX_2048_4095 }, -+ { "tx_4096_8191_oct", GEN_STAT(mib.tx_4096_8191), -+ ETHSW_MIB_RX_4096_8191 }, -+ { "tx_8192_9728_oct", GEN_STAT(mib.tx_8192_9728), -+ ETHSW_MIB_RX_8192_9728 }, -+ { "tx_oversize", GEN_STAT(mib.tx_ovr), ETHSW_MIB_RX_OVR }, -+ { "tx_oversize_drop", GEN_STAT(mib.tx_ovr), ETHSW_MIB_RX_OVR_DISC }, -+ { "tx_dropped", GEN_STAT(mib.tx_drop), ETHSW_MIB_RX_DROP }, -+ { "tx_undersize", GEN_STAT(mib.tx_underrun), ETHSW_MIB_RX_UND }, -+ { "tx_pause", GEN_STAT(mib.tx_pause), ETHSW_MIB_RX_PAUSE }, -+ -+ { "rx_good_octets", GEN_STAT(mib.rx_gd_octets), ETHSW_MIB_TX_ALL_OCT }, -+ { "rx_broadcast", GEN_STAT(mib.rx_brdcast), ETHSW_MIB_TX_BRDCAST }, -+ { "rx_multicast", GEN_STAT(mib.rx_mult), ETHSW_MIB_TX_MULT }, -+ { "rx_unicast", GEN_STAT(mib.rx_unicast), ETHSW_MIB_TX_MULT }, -+ { "rx_pause", GEN_STAT(mib.rx_pause), ETHSW_MIB_TX_PAUSE }, -+ { "rx_dropped", GEN_STAT(mib.rx_drop), ETHSW_MIB_TX_DROP_PKTS }, -+ -+}; -+ -+#define BCM_ENETSW_STATS_LEN \ -+ (sizeof(bcm_enetsw_gstrings_stats) / sizeof(struct bcm_enet_stats)) -+ -+static void bcm_enetsw_get_strings(struct net_device *netdev, -+ u32 stringset, u8 *data) -+{ -+ int i; -+ -+ switch (stringset) { -+ case ETH_SS_STATS: -+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) { -+ memcpy(data + i * ETH_GSTRING_LEN, -+ bcm_enetsw_gstrings_stats[i].stat_string, -+ ETH_GSTRING_LEN); -+ } -+ break; -+ } -+} -+ -+static int bcm_enetsw_get_sset_count(struct net_device *netdev, -+ int string_set) -+{ -+ switch (string_set) { -+ case ETH_SS_STATS: -+ return BCM_ENETSW_STATS_LEN; -+ default: -+ return -EINVAL; -+ } -+} -+ -+static void bcm_enetsw_get_drvinfo(struct net_device *netdev, -+ struct ethtool_drvinfo *drvinfo) -+{ -+ strncpy(drvinfo->driver, bcm_enet_driver_name, 32); -+ strncpy(drvinfo->version, bcm_enet_driver_version, 32); -+ strncpy(drvinfo->fw_version, "N/A", 32); -+ strncpy(drvinfo->bus_info, "bcm63xx", 32); -+ drvinfo->n_stats = BCM_ENETSW_STATS_LEN; -+} -+ -+static void bcm_enetsw_get_ethtool_stats(struct net_device *netdev, -+ struct ethtool_stats *stats, -+ u64 *data) -+{ -+ struct bcm_enet_priv *priv; -+ int i; -+ -+ priv = netdev_priv(netdev); -+ -+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) { -+ const struct bcm_enet_stats *s; -+ u32 lo, hi; -+ char *p; -+ int reg; -+ -+ s = &bcm_enetsw_gstrings_stats[i]; -+ -+ reg = s->mib_reg; -+ if (reg == -1) -+ continue; -+ -+ lo = enetsw_readl(priv, ENETSW_MIB_REG(reg)); -+ p = (char *)priv + s->stat_offset; -+ -+ if (s->sizeof_stat == sizeof(u64)) { -+ hi = enetsw_readl(priv, ENETSW_MIB_REG(reg + 1)); -+ *(u64 *)p = ((u64)hi << 32 | lo); -+ } else -+ *(u32 *)p = lo; -+ } -+ -+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) { -+ const struct bcm_enet_stats *s; -+ char *p; -+ -+ s = &bcm_enetsw_gstrings_stats[i]; -+ -+ if (s->mib_reg == -1) -+ p = (char *)&netdev->stats + s->stat_offset; -+ else -+ p = (char *)priv + s->stat_offset; -+ -+ data[i] = (s->sizeof_stat == sizeof(u64)) ? -+ *(u64 *)p : *(u32 *)p; -+ } -+} -+ -+static void bcm_enetsw_get_ringparam(struct net_device *dev, -+ struct ethtool_ringparam *ering) -+{ -+ struct bcm_enet_priv *priv; -+ -+ priv = netdev_priv(dev); -+ -+ /* rx/tx ring is actually only limited by memory */ -+ ering->rx_max_pending = 8192; -+ ering->tx_max_pending = 8192; -+ ering->rx_mini_max_pending = 0; -+ ering->rx_jumbo_max_pending = 0; -+ ering->rx_pending = priv->rx_ring_size; -+ ering->tx_pending = priv->tx_ring_size; -+} -+ -+static int bcm_enetsw_set_ringparam(struct net_device *dev, -+ struct ethtool_ringparam *ering) -+{ -+ struct bcm_enet_priv *priv; -+ int was_running; -+ -+ priv = netdev_priv(dev); -+ -+ was_running = 0; -+ if (netif_running(dev)) { -+ bcm_enetsw_stop(dev); -+ was_running = 1; -+ } -+ -+ priv->rx_ring_size = ering->rx_pending; -+ priv->tx_ring_size = ering->tx_pending; -+ -+ if (was_running) { -+ int err; -+ -+ err = bcm_enetsw_open(dev); -+ if (err) -+ dev_close(dev); -+ } -+ return 0; -+} -+ -+static struct ethtool_ops bcm_enetsw_ethtool_ops = { -+ .get_strings = bcm_enetsw_get_strings, -+ .get_sset_count = bcm_enetsw_get_sset_count, -+ .get_ethtool_stats = bcm_enetsw_get_ethtool_stats, -+ .get_drvinfo = bcm_enetsw_get_drvinfo, -+ .get_ringparam = bcm_enetsw_get_ringparam, -+ .set_ringparam = bcm_enetsw_set_ringparam, -+}; -+ -+/* -+ * allocate netdevice, request register memory and register device. -+ */ -+static int __devinit bcm_enetsw_probe(struct platform_device *pdev) -+{ -+ struct bcm_enet_priv *priv; -+ struct net_device *dev; -+ struct bcm63xx_enetsw_platform_data *pd; -+ struct resource *res_mem; -+ int ret, irq_rx, irq_tx; -+ -+ /* stop if shared driver failed, assume driver->probe will be -+ * called in the same order we register devices (correct ?) */ -+ if (!bcm_enet_shared_base[0]) -+ return -ENODEV; -+ -+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ irq_rx = platform_get_irq(pdev, 0); -+ irq_tx = platform_get_irq(pdev, 1); -+ if (!res_mem || irq_rx < 0 || irq_tx < 0) -+ return -ENODEV; -+ -+ ret = 0; -+ dev = alloc_etherdev(sizeof(*priv)); -+ if (!dev) -+ return -ENOMEM; -+ priv = netdev_priv(dev); -+ memset(priv, 0, sizeof(*priv)); -+ -+ /* initialize default and fetch platform data */ -+ priv->irq_rx = irq_rx; -+ priv->irq_tx = irq_tx; -+ priv->rx_ring_size = BCMENET_DEF_RX_DESC; -+ priv->tx_ring_size = BCMENET_DEF_TX_DESC; -+ -+ pd = pdev->dev.platform_data; -+ if (pd) { -+ memcpy(dev->dev_addr, pd->mac_addr, ETH_ALEN); -+ memcpy(priv->used_ports, pd->used_ports, -+ sizeof (pd->used_ports)); -+ } -+ -+ ret = compute_hw_mtu(priv, dev->mtu); -+ if (ret) -+ goto out; -+ -+ if (!request_mem_region(res_mem->start, resource_size(res_mem), -+ "bcm63xx_enetsw")) { -+ ret = -EBUSY; -+ goto out; -+ } -+ -+ priv->base = ioremap(res_mem->start, resource_size(res_mem)); -+ if (priv->base == NULL) { -+ ret = -ENOMEM; -+ goto out_release_mem; -+ } -+ -+ priv->mac_clk = clk_get(&pdev->dev, "enetsw"); -+ if (IS_ERR(priv->mac_clk)) { -+ ret = PTR_ERR(priv->mac_clk); -+ goto out_unmap; -+ } -+ clk_enable(priv->mac_clk); -+ -+ priv->rx_chan = 0; -+ priv->tx_chan = 1; -+ spin_lock_init(&priv->rx_lock); -+ -+ /* init rx timeout (used for oom) */ -+ init_timer(&priv->rx_timeout); -+ priv->rx_timeout.function = bcm_enet_refill_rx_timer; -+ priv->rx_timeout.data = (unsigned long)dev; -+ -+ /* register netdevice */ -+ dev->netdev_ops = &bcm_enetsw_ops; -+ netif_napi_add(dev, &priv->napi, bcm_enet_poll, 16); -+ SET_ETHTOOL_OPS(dev, &bcm_enetsw_ethtool_ops); -+ SET_NETDEV_DEV(dev, &pdev->dev); -+ -+ spin_lock_init(&priv->enetsw_mdio_lock); -+ -+ ret = register_netdev(dev); -+ if (ret) -+ goto out_put_clk; -+ -+ netif_carrier_off(dev); -+ platform_set_drvdata(pdev, dev); -+ priv->pdev = pdev; -+ priv->net_dev = dev; -+ -+ return 0; -+ -+out_put_clk: -+ clk_put(priv->mac_clk); -+ -+out_unmap: -+ iounmap(priv->base); -+ -+out_release_mem: -+ release_mem_region(res_mem->start, resource_size(res_mem)); -+out: -+ free_netdev(dev); -+ return ret; -+} -+ -+ -+/* -+ * exit func, stops hardware and unregisters netdevice -+ */ -+static int __devexit bcm_enetsw_remove(struct platform_device *pdev) -+{ -+ struct bcm_enet_priv *priv; -+ struct net_device *dev; -+ struct resource *res; -+ -+ /* stop netdevice */ -+ dev = platform_get_drvdata(pdev); -+ priv = netdev_priv(dev); -+ unregister_netdev(dev); -+ -+ /* release device resources */ -+ iounmap(priv->base); -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ release_mem_region(res->start, resource_size(res)); -+ -+ platform_set_drvdata(pdev, NULL); -+ free_netdev(dev); -+ return 0; -+} -+ -+struct platform_driver bcm63xx_enetsw_driver = { -+ .probe = bcm_enetsw_probe, -+ .remove = __devexit_p(bcm_enetsw_remove), -+ .driver = { -+ .name = "bcm63xx_enetsw", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+/* -+ * reserve & remap memory space shared between all macs -+ */ -+static int __devinit bcm_enet_shared_probe(struct platform_device *pdev) -+{ -+ struct resource *res; -+ int ret, i, requested[3]; -+ -+ memset(bcm_enet_shared_base, 0, sizeof (bcm_enet_shared_base)); -+ memset(requested, 0, sizeof (requested)); -+ -+ for (i = 0; i < 3; i++) { -+ void __iomem *p; -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ if (!res) { -+ ret = -EINVAL; -+ goto fail; -+ } -+ -+ if (!request_mem_region(res->start, resource_size(res), -+ "bcm63xx_enet_dma")) { -+ ret = -EBUSY; -+ goto fail; -+ } -+ requested[i] = 0; -+ -+ p = ioremap(res->start, resource_size(res)); -+ if (!p) { -+ ret = -ENOMEM; -+ goto fail; -+ } -+ -+ bcm_enet_shared_base[i] = p; -+ } -+ -+ return 0; -+ -+fail: -+ for (i = 0; i < 3; i++) { -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ if (!res) -+ continue; -+ if (bcm_enet_shared_base[i]) -+ iounmap(bcm_enet_shared_base[i]); -+ if (requested[i]) -+ release_mem_region(res->start, resource_size(res)); -+ } -+ return ret; -+} -+ -+static int __devexit bcm_enet_shared_remove(struct platform_device *pdev) -+{ -+ struct resource *res; -+ int i; -+ -+ for (i = 0; i < 3; i++) { -+ iounmap(bcm_enet_shared_base[i]); -+ res = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ release_mem_region(res->start, resource_size(res)); -+ } -+ return 0; -+} -+ -+/* -+ * this "shared" driver is needed because both macs share a single -+ * address space -+ */ -+struct platform_driver bcm63xx_enet_shared_driver = { -+ .probe = bcm_enet_shared_probe, -+ .remove = __devexit_p(bcm_enet_shared_remove), -+ .driver = { -+ .name = "bcm63xx_enet_shared", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+/* -+ * entry point -+ */ -+static int __init bcm_enet_init(void) -+{ -+ int ret; -+ -+ ret = platform_driver_register(&bcm63xx_enet_shared_driver); -+ if (ret) -+ return ret; -+ -+ ret = platform_driver_register(&bcm63xx_enet_driver); -+ if (ret) -+ platform_driver_unregister(&bcm63xx_enet_shared_driver); -+ -+ ret = platform_driver_register(&bcm63xx_enetsw_driver); -+ if (ret) { -+ platform_driver_unregister(&bcm63xx_enet_driver); -+ platform_driver_unregister(&bcm63xx_enet_shared_driver); -+ } - - return ret; - } -@@ -2018,6 +2937,7 @@ static int __init bcm_enet_init(void) - static void __exit bcm_enet_exit(void) - { - platform_driver_unregister(&bcm63xx_enet_driver); -+ platform_driver_unregister(&bcm63xx_enetsw_driver); - platform_driver_unregister(&bcm63xx_enet_shared_driver); - } - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -112,11 +112,60 @@ struct bcm_enet_desc { - #define ETH_MIB_RX_CNTRL 54 - - -+/* -+ * SW MIB Counters register definitions -+*/ -+#define ETHSW_MIB_TX_ALL_OCT 0 -+#define ETHSW_MIB_TX_DROP_PKTS 2 -+#define ETHSW_MIB_TX_QOS_PKTS 3 -+#define ETHSW_MIB_TX_BRDCAST 4 -+#define ETHSW_MIB_TX_MULT 5 -+#define ETHSW_MIB_TX_UNI 6 -+#define ETHSW_MIB_TX_COL 7 -+#define ETHSW_MIB_TX_1_COL 8 -+#define ETHSW_MIB_TX_M_COL 9 -+#define ETHSW_MIB_TX_DEF 10 -+#define ETHSW_MIB_TX_LATE 11 -+#define ETHSW_MIB_TX_EX_COL 12 -+#define ETHSW_MIB_TX_PAUSE 14 -+#define ETHSW_MIB_TX_QOS_OCT 15 -+ -+#define ETHSW_MIB_RX_ALL_OCT 17 -+#define ETHSW_MIB_RX_UND 19 -+#define ETHSW_MIB_RX_PAUSE 20 -+#define ETHSW_MIB_RX_64 21 -+#define ETHSW_MIB_RX_65_127 22 -+#define ETHSW_MIB_RX_128_255 23 -+#define ETHSW_MIB_RX_256_511 24 -+#define ETHSW_MIB_RX_512_1023 25 -+#define ETHSW_MIB_RX_1024_1522 26 -+#define ETHSW_MIB_RX_OVR 27 -+#define ETHSW_MIB_RX_JAB 28 -+#define ETHSW_MIB_RX_ALIGN 29 -+#define ETHSW_MIB_RX_CRC 30 -+#define ETHSW_MIB_RX_GD_OCT 31 -+#define ETHSW_MIB_RX_DROP 33 -+#define ETHSW_MIB_RX_UNI 34 -+#define ETHSW_MIB_RX_MULT 35 -+#define ETHSW_MIB_RX_BRDCAST 36 -+#define ETHSW_MIB_RX_SA_CHANGE 37 -+#define ETHSW_MIB_RX_FRAG 38 -+#define ETHSW_MIB_RX_OVR_DISC 39 -+#define ETHSW_MIB_RX_SYM 40 -+#define ETHSW_MIB_RX_QOS_PKTS 41 -+#define ETHSW_MIB_RX_QOS_OCT 42 -+#define ETHSW_MIB_RX_1523_2047 44 -+#define ETHSW_MIB_RX_2048_4095 45 -+#define ETHSW_MIB_RX_4096_8191 46 -+#define ETHSW_MIB_RX_8192_9728 47 -+ -+ - struct bcm_enet_mib_counters { - u64 tx_gd_octets; - u32 tx_gd_pkts; - u32 tx_all_octets; - u32 tx_all_pkts; -+ u32 tx_unicast; - u32 tx_brdcast; - u32 tx_mult; - u32 tx_64; -@@ -125,7 +174,12 @@ struct bcm_enet_mib_counters { - u32 tx_256_511; - u32 tx_512_1023; - u32 tx_1024_max; -+ u32 tx_1523_2047; -+ u32 tx_2048_4095; -+ u32 tx_4096_8191; -+ u32 tx_8192_9728; - u32 tx_jab; -+ u32 tx_drop; - u32 tx_ovr; - u32 tx_frag; - u32 tx_underrun; -@@ -142,6 +196,7 @@ struct bcm_enet_mib_counters { - u32 rx_all_octets; - u32 rx_all_pkts; - u32 rx_brdcast; -+ u32 rx_unicast; - u32 rx_mult; - u32 rx_64; - u32 rx_65_127; -@@ -297,6 +352,22 @@ struct bcm_enet_priv { - - /* maximum hardware transmit/receive size */ - unsigned int hw_mtu; -+ -+ /* port mapping for switch devices */ -+ struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; -+ int sw_port_link[ENETSW_MAX_PORT]; -+ -+ /* used to poll switch port state */ -+ struct timer_list swphy_poll; -+ spinlock_t enetsw_mdio_lock; - }; - -+static inline int bcm_enet_is_sw(struct bcm_enet_priv *priv) -+{ -+ if (BCMCPU_IS_6368()) -+ return 1; -+ else -+ return 0; -+} -+ - #endif /* ! BCM63XX_ENET_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/416-bcm63xx_enet-reset-port-link-state-in-bcm_enetsw_ope.patch b/target/linux/brcm63xx/patches-3.6/416-bcm63xx_enet-reset-port-link-state-in-bcm_enetsw_ope.patch deleted file mode 100644 index 6d8e5a72db..0000000000 --- a/target/linux/brcm63xx/patches-3.6/416-bcm63xx_enet-reset-port-link-state-in-bcm_enetsw_ope.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 6d5c5bb13db3fd8e3dd0b82742b3957f41a4a3ac Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 24 May 2012 20:38:58 +0200 -Subject: [PATCH] bcm63xx_enet: reset port link state in bcm_enetsw_open - -bcm_enetsw_open disables all ports, but does not reset their link state. -This results in connected ports staying disabled after a ifdown/ifup -cycle, since bcm_enetsw_phy_poll only enables them if their current state -is different from the stored link state. - -Fix this by also resetting the port link state. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -2213,6 +2213,8 @@ static int bcm_enetsw_open(struct net_de - enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK | - ENETSW_PTCTRL_TXDIS_MASK, - ENETSW_PTCTRL_REG(i)); -+ -+ priv->sw_port_link[i] = 0; - } - - /* reset mib */ diff --git a/target/linux/brcm63xx/patches-3.6/417-bcm63xx_enet-don-t-overwrite-settings-when-setting-d.patch b/target/linux/brcm63xx/patches-3.6/417-bcm63xx_enet-don-t-overwrite-settings-when-setting-d.patch deleted file mode 100644 index 407c8169ec..0000000000 --- a/target/linux/brcm63xx/patches-3.6/417-bcm63xx_enet-don-t-overwrite-settings-when-setting-d.patch +++ /dev/null @@ -1,20 +0,0 @@ -From e79bc74f76361020d820ed4611d28f70ebd845ca Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 10 Jul 2012 10:44:09 +0200 -Subject: [PATCH 34/84] bcm63xx_enet: don't overwrite settings when setting duplex on force - ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 2 +- - 1 files changed, 1 insertions(+), 1 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -2333,7 +2333,7 @@ static int bcm_enetsw_open(struct net_de - } - - if (port->force_duplex_full) -- override = ENETSW_IMPOV_FDX_MASK; -+ override |= ENETSW_IMPOV_FDX_MASK; - - - enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i)); diff --git a/target/linux/brcm63xx/patches-3.6/418-bcm63xx_enet-store-the-number-of-ports-instead-of-ha.patch b/target/linux/brcm63xx/patches-3.6/418-bcm63xx_enet-store-the-number-of-ports-instead-of-ha.patch deleted file mode 100644 index 232668b7c9..0000000000 --- a/target/linux/brcm63xx/patches-3.6/418-bcm63xx_enet-store-the-number-of-ports-instead-of-ha.patch +++ /dev/null @@ -1,98 +0,0 @@ -From efe31ec8fca92162fc21630611971345014a81a0 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 10 Jul 2012 10:39:30 +0200 -Subject: [PATCH 33/84] bcm63xx_enet: store the number of ports instead of hardcoding them - -This will be needed for devices with a different number of ports ---- - arch/mips/bcm63xx/dev-enet.c | 2 ++ - .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 2 ++ - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 9 +++++---- - drivers/net/ethernet/broadcom/bcm63xx_enet.h | 1 + - 4 files changed, 10 insertions(+), 4 deletions(-) - ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -239,6 +239,8 @@ bcm63xx_enetsw_register(const struct bcm - - memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof (*pd)); - -+ enetsw_pd.num_ports = ENETSW_PORTS_6368; -+ - ret = platform_device_register(&bcm63xx_enetsw_device); - if (ret) - return ret; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -43,6 +43,7 @@ struct bcm63xx_enet_platform_data { - * on board ethernet switch platform data - */ - #define ENETSW_MAX_PORT 6 -+#define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */ - - struct bcm63xx_enetsw_port { - int used; -@@ -58,6 +59,7 @@ struct bcm63xx_enetsw_port { - - struct bcm63xx_enetsw_platform_data { - char mac_addr[ETH_ALEN]; -+ int num_ports; - struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; - }; - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -2041,7 +2041,7 @@ static void swphy_poll_timer(unsigned lo - struct bcm_enet_priv *priv = (struct bcm_enet_priv *)data; - unsigned int i; - -- for (i = 0; i < ARRAY_SIZE(priv->used_ports); i++) { -+ for (i = 0; i < priv->num_ports; i++) { - struct bcm63xx_enetsw_port *port; - int val, j, up, advertise, lpa, lpa2, speed, duplex, media; - u8 override; -@@ -2207,7 +2207,7 @@ static int bcm_enetsw_open(struct net_de - priv->rx_curr_desc = 0; - - /* disable all ports */ -- for (i = 0; i < 6; i++) { -+ for (i = 0; i < priv->num_ports; i++) { - enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK, - ENETSW_PORTOV_REG(i)); - enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK | -@@ -2303,7 +2303,7 @@ static int bcm_enetsw_open(struct net_de - /* - * apply override config for bypass_link ports here. - */ -- for (i = 0; i < ARRAY_SIZE(priv->used_ports); i++) { -+ for (i = 0; i < priv->num_ports; i++) { - struct bcm63xx_enetsw_port *port; - u8 override; - port = &priv->used_ports[i]; -@@ -2447,7 +2447,7 @@ static int bcm_enetsw_phy_is_external(st - { - int i; - -- for (i = 0; i < (int)ARRAY_SIZE(priv->used_ports); ++i) { -+ for (i = 0; i < priv->num_ports; ++i) { - if (!priv->used_ports[i].used) - continue; - if (priv->used_ports[i].phy_id == phy_id) -@@ -2735,6 +2735,7 @@ static int __devinit bcm_enetsw_probe(st - memcpy(dev->dev_addr, pd->mac_addr, ETH_ALEN); - memcpy(priv->used_ports, pd->used_ports, - sizeof (pd->used_ports)); -+ priv->num_ports = pd->num_ports; - } - - ret = compute_hw_mtu(priv, dev->mtu); ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -354,6 +354,7 @@ struct bcm_enet_priv { - unsigned int hw_mtu; - - /* port mapping for switch devices */ -+ int num_ports; - struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; - int sw_port_link[ENETSW_MAX_PORT]; - diff --git a/target/linux/brcm63xx/patches-3.6/419-bcm63xx_enet-store-is_sw-in-a-variable-instead-of-ch.patch b/target/linux/brcm63xx/patches-3.6/419-bcm63xx_enet-store-is_sw-in-a-variable-instead-of-ch.patch deleted file mode 100644 index 6f73477ab3..0000000000 --- a/target/linux/brcm63xx/patches-3.6/419-bcm63xx_enet-store-is_sw-in-a-variable-instead-of-ch.patch +++ /dev/null @@ -1,73 +0,0 @@ -From ef581388c45dbc48f7bbe050e87deb1e3c63a698 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 10 Jul 2012 10:52:02 +0200 -Subject: [PATCH 35/84] bcm63xx_enet: store is_sw in a variable instead of checking the cpuid - -Reduces the number of changes needed for making enetsw work on new -chips. ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 7 +++++-- - drivers/net/ethernet/broadcom/bcm63xx_enet.h | 10 ++-------- - 2 files changed, 7 insertions(+), 10 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -364,7 +364,7 @@ static int bcm_enet_receive_queue(struct - } - - /* recycle packet if it's marked as bad */ -- if (!bcm_enet_is_sw(priv) && -+ if (!priv->enet_is_sw && - unlikely(len_stat & DMADESC_ERR_MASK)) { - dev->stats.rx_errors++; - -@@ -597,7 +597,7 @@ static int bcm_enet_start_xmit(struct sk - } - - /* pad small packets sent on a switch device */ -- if (bcm_enet_is_sw(priv) && skb->len < 64) { -+ if (priv->enet_is_sw && skb->len < 64) { - int needed = 64 - skb->len; - char *data; - -@@ -1700,6 +1700,8 @@ static int __devinit bcm_enet_probe(stru - return -ENOMEM; - priv = netdev_priv(dev); - -+ priv->enet_is_sw = false; -+ - ret = compute_hw_mtu(priv, dev->mtu); - if (ret) - goto out; -@@ -2725,6 +2727,7 @@ static int __devinit bcm_enetsw_probe(st - memset(priv, 0, sizeof(*priv)); - - /* initialize default and fetch platform data */ -+ priv->enet_is_sw = true; - priv->irq_rx = irq_rx; - priv->irq_tx = irq_tx; - priv->rx_ring_size = BCMENET_DEF_RX_DESC; ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -353,6 +353,8 @@ struct bcm_enet_priv { - /* maximum hardware transmit/receive size */ - unsigned int hw_mtu; - -+ bool enet_is_sw; -+ - /* port mapping for switch devices */ - int num_ports; - struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; -@@ -363,12 +365,4 @@ struct bcm_enet_priv { - spinlock_t enetsw_mdio_lock; - }; - --static inline int bcm_enet_is_sw(struct bcm_enet_priv *priv) --{ -- if (BCMCPU_IS_6368()) -- return 1; -- else -- return 0; --} -- - #endif /* ! BCM63XX_ENET_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/420-BCM63XX-allow-enetsw-without-tx-irq.patch b/target/linux/brcm63xx/patches-3.6/420-BCM63XX-allow-enetsw-without-tx-irq.patch deleted file mode 100644 index 6396b626df..0000000000 --- a/target/linux/brcm63xx/patches-3.6/420-BCM63XX-allow-enetsw-without-tx-irq.patch +++ /dev/null @@ -1,69 +0,0 @@ -From 625894c377ba266c0044675b53f05d65db6355b6 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 8 Jul 2012 13:07:52 +0200 -Subject: [PATCH 38/84] BCM63XX: allow enetsw without tx irq - ---- - arch/mips/bcm63xx/dev-enet.c | 2 ++ - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 18 +++++++++++------- - 2 files changed, 13 insertions(+), 7 deletions(-) - ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -236,6 +236,8 @@ bcm63xx_enetsw_register(const struct bcm - enetsw_res[0].end += RSET_ENETSW_SIZE - 1; - enetsw_res[1].start = bcm63xx_get_irq_number(IRQ_ENETSW_RXDMA0); - enetsw_res[2].start = bcm63xx_get_irq_number(IRQ_ENETSW_TXDMA0); -+ if (!enetsw_res[2].start) -+ enetsw_res[2].start = -1; - - memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof (*pd)); - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -2151,10 +2151,12 @@ static int bcm_enetsw_open(struct net_de - if (ret) - goto out_freeirq; - -- ret = request_irq(priv->irq_tx, bcm_enet_isr_dma, -- IRQF_DISABLED, dev->name, dev); -- if (ret) -- goto out_freeirq_rx; -+ if (priv->irq_tx != -1) { -+ ret = request_irq(priv->irq_tx, bcm_enet_isr_dma, -+ IRQF_DISABLED, dev->name, dev); -+ if (ret) -+ goto out_freeirq_rx; -+ } - - /* allocate rx dma ring */ - size = priv->rx_ring_size * sizeof(struct bcm_enet_desc); -@@ -2376,7 +2378,8 @@ out_free_rx_ring: - priv->rx_desc_cpu, priv->rx_desc_dma); - - out_freeirq_tx: -- free_irq(priv->irq_tx, dev); -+ if (priv->irq_tx != -1) -+ free_irq(priv->irq_tx, dev); - - out_freeirq_rx: - free_irq(priv->irq_rx, dev); -@@ -2433,7 +2436,8 @@ static int bcm_enetsw_stop(struct net_de - priv->rx_desc_cpu, priv->rx_desc_dma); - dma_free_coherent(kdev, priv->tx_desc_alloc_size, - priv->tx_desc_cpu, priv->tx_desc_dma); -- free_irq(priv->irq_tx, dev); -+ if (priv->irq_tx != -1) -+ free_irq(priv->irq_tx, dev); - free_irq(priv->irq_rx, dev); - - return 0; -@@ -2716,7 +2720,7 @@ static int __devinit bcm_enetsw_probe(st - res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); - irq_rx = platform_get_irq(pdev, 0); - irq_tx = platform_get_irq(pdev, 1); -- if (!res_mem || irq_rx < 0 || irq_tx < 0) -+ if (!res_mem || irq_rx < 0) - return -ENODEV; - - ret = 0; diff --git a/target/linux/brcm63xx/patches-3.6/421-BCM63XX-use-port-id-for-deciding-external-phy.patch b/target/linux/brcm63xx/patches-3.6/421-BCM63XX-use-port-id-for-deciding-external-phy.patch deleted file mode 100644 index da7013d8ff..0000000000 --- a/target/linux/brcm63xx/patches-3.6/421-BCM63XX-use-port-id-for-deciding-external-phy.patch +++ /dev/null @@ -1,87 +0,0 @@ -From 85e4551e033df7cb043e93042661fc1e58799efa Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 8 Jul 2012 15:36:23 +0200 -Subject: [PATCH 52/84] BCM63XX: use port id for deciding external phy - -Ports 0-3 always use the internal phy, while 4+ always need an external -phy to work. ---- - .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 3 ++- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 15 ++++++++------- - drivers/net/ethernet/broadcom/bcm63xx_enet.h | 5 +++++ - 3 files changed, 15 insertions(+), 8 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -45,9 +45,10 @@ struct bcm63xx_enet_platform_data { - #define ENETSW_MAX_PORT 6 - #define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */ - -+#define ENETSW_RGMII_PORT0 4 -+ - struct bcm63xx_enetsw_port { - int used; -- int external_phy; - int phy_id; - - int bypass_link; ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -2046,6 +2046,7 @@ static void swphy_poll_timer(unsigned lo - for (i = 0; i < priv->num_ports; i++) { - struct bcm63xx_enetsw_port *port; - int val, j, up, advertise, lpa, lpa2, speed, duplex, media; -+ int external_phy = bcm_enet_port_is_rgmii(i); - u8 override; - - port = &priv->used_ports[i]; -@@ -2057,7 +2058,7 @@ static void swphy_poll_timer(unsigned lo - - /* dummy read to clear */ - for (j = 0; j < 2; j++) -- val = bcmenet_sw_mdio_read(priv, port->external_phy, -+ val = bcmenet_sw_mdio_read(priv, external_phy, - port->phy_id, MII_BMSR); - - if (val == 0xffff) -@@ -2081,14 +2082,14 @@ static void swphy_poll_timer(unsigned lo - continue; - } - -- advertise = bcmenet_sw_mdio_read(priv, port->external_phy, -+ advertise = bcmenet_sw_mdio_read(priv, external_phy, - port->phy_id, MII_ADVERTISE); - -- lpa = bcmenet_sw_mdio_read(priv, port->external_phy, -- port->phy_id, MII_LPA); -+ lpa = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id, -+ MII_LPA); - -- lpa2 = bcmenet_sw_mdio_read(priv, port->external_phy, -- port->phy_id, MII_STAT1000); -+ lpa2 = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id, -+ MII_STAT1000); - - /* figure out media and duplex from advertise and LPA values */ - media = mii_nway_result(lpa & advertise); -@@ -2457,7 +2458,7 @@ static int bcm_enetsw_phy_is_external(st - if (!priv->used_ports[i].used) - continue; - if (priv->used_ports[i].phy_id == phy_id) -- return priv->used_ports[i].external_phy; -+ return bcm_enet_port_is_rgmii(i); - } - - printk_once(KERN_WARNING "bcm63xx_enet: could not find a used port " ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -365,4 +365,9 @@ struct bcm_enet_priv { - spinlock_t enetsw_mdio_lock; - }; - -+static inline int bcm_enet_port_is_rgmii(int portid) -+{ -+ return portid >= ENETSW_RGMII_PORT0; -+} -+ - #endif /* ! BCM63XX_ENET_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/422-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch b/target/linux/brcm63xx/patches-3.6/422-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch deleted file mode 100644 index 7d1f3f3f81..0000000000 --- a/target/linux/brcm63xx/patches-3.6/422-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch +++ /dev/null @@ -1,53 +0,0 @@ -From d8237d704fc25eb2fc25ef4403608b78c6a6d4be Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 15 Jul 2012 20:08:57 +0200 -Subject: [PATCH 54/81] bcm63xx_enet: enable rgmii clock on external ports - ---- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 13 +++++++++++++ - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 12 ++++++++++++ - 2 files changed, 25 insertions(+), 0 deletions(-) - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -838,6 +838,19 @@ - #define ENETSW_PORTOV_FDX_MASK (1 << 1) - #define ENETSW_PORTOV_LINKUP_MASK (1 << 0) - -+/* Port RGMII control register */ -+#define ENETSW_RGMII_CTRL_REG(x) (0x60 + (x)) -+#define ENETSW_RGMII_CTRL_GMII_CLK_EN (1 << 7) -+#define ENETSW_RGMII_CTRL_MII_OVERRIDE_EN (1 << 6) -+#define ENETSW_RGMII_CTRL_MII_MODE_MASK (3 << 4) -+#define ENETSW_RGMII_CTRL_RGMII_MODE (0 << 4) -+#define ENETSW_RGMII_CTRL_MII_MODE (1 << 4) -+#define ENETSW_RGMII_CTRL_RVMII_MODE (2 << 4) -+#define ENETSW_RGMII_CTRL_TIMING_SEL_EN (1 << 0) -+ -+/* Port RGMII timing register */ -+#define ENETSW_RGMII_TIMING_REG(x) (0x68 + (x)) -+ - /* MDIO control register */ - #define ENETSW_MDIOC_REG (0xb0) - #define ENETSW_MDIOC_EXT_MASK (1 << 16) ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -2222,6 +2222,18 @@ static int bcm_enetsw_open(struct net_de - priv->sw_port_link[i] = 0; - } - -+ /* enable external ports */ -+ for (i = ENETSW_RGMII_PORT0; i < priv->num_ports; i++) { -+ u8 rgmii_ctrl; -+ -+ if (!priv->used_ports[i].used) -+ continue; -+ -+ rgmii_ctrl = enetsw_readb(priv, ENETSW_RGMII_CTRL_REG(i)); -+ rgmii_ctrl |= ENETSW_RGMII_CTRL_GMII_CLK_EN; -+ enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i)); -+ } -+ - /* reset mib */ - val = enetsw_readb(priv, ENETSW_GMCR_REG); - val |= ENETSW_GMCR_RST_MIB_MASK; diff --git a/target/linux/brcm63xx/patches-3.6/423-bcm63xx_enet-fix-lockup-on-BCM6328.patch b/target/linux/brcm63xx/patches-3.6/423-bcm63xx_enet-fix-lockup-on-BCM6328.patch deleted file mode 100644 index 4306ce753e..0000000000 --- a/target/linux/brcm63xx/patches-3.6/423-bcm63xx_enet-fix-lockup-on-BCM6328.patch +++ /dev/null @@ -1,93 +0,0 @@ -From 382a0b0dc4cbd0e0fbfd6c2d132e972c3d1245b0 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 13 Nov 2011 14:59:37 +0100 -Subject: [PATCH 39/84] bcm63xx_enet: fix lockup on BCM6328 - -BCM6328 locks up on a maxburst size of 16, reduce it to 8 for BCM6328 and -BCM6368. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - drivers/net/ethernet/broadcom/bcm63xx_enet.c | 13 +++++++------ - drivers/net/ethernet/broadcom/bcm63xx_enet.h | 4 ++++ - 2 files changed, 11 insertions(+), 6 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -261,7 +261,6 @@ static int bcm_enet_refill_rx(struct net - if (!skb) - break; - priv->rx_skb[desc_idx] = skb; -- - p = dma_map_single(&priv->pdev->dev, skb->data, - priv->rx_skb_size, - DMA_FROM_DEVICE); -@@ -995,9 +994,9 @@ static int bcm_enet_open(struct net_devi - enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG); - - /* set dma maximum burst len */ -- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ enet_dmac_writel(priv, priv->dma_maxburst, - ENETDMAC_MAXBURST_REG(priv->rx_chan)); -- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ enet_dmac_writel(priv, priv->dma_maxburst, - ENETDMAC_MAXBURST_REG(priv->tx_chan)); - - /* set correct transmit fifo watermark */ -@@ -1593,7 +1592,7 @@ static int compute_hw_mtu(struct bcm_ene - * it's appended - */ - priv->rx_skb_size = ALIGN(actual_mtu + ETH_FCS_LEN, -- BCMENET_DMA_MAXBURST * 4); -+ priv->dma_maxburst * 4); - return 0; - } - -@@ -1701,6 +1700,7 @@ static int __devinit bcm_enet_probe(stru - priv = netdev_priv(dev); - - priv->enet_is_sw = false; -+ priv->dma_maxburst = BCMENET_DMA_MAXBURST; - - ret = compute_hw_mtu(priv, dev->mtu); - if (ret) -@@ -2282,9 +2282,9 @@ static int bcm_enetsw_open(struct net_de - enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); - - /* set dma maximum burst len */ -- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ enet_dmac_writel(priv, priv->dma_maxburst, - ENETDMAC_MAXBURST_REG(priv->rx_chan)); -- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST, -+ enet_dmac_writel(priv, priv->dma_maxburst, - ENETDMAC_MAXBURST_REG(priv->tx_chan)); - - /* set flow control low/high threshold to 1/3 / 2/3 */ -@@ -2749,6 +2749,7 @@ static int __devinit bcm_enetsw_probe(st - priv->irq_tx = irq_tx; - priv->rx_ring_size = BCMENET_DEF_RX_DESC; - priv->tx_ring_size = BCMENET_DEF_TX_DESC; -+ priv->dma_maxburst = BCMENETSW_DMA_MAXBURST; - - pd = pdev->dev.platform_data; - if (pd) { ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -17,6 +17,7 @@ - - /* maximum burst len for dma (4 bytes unit) */ - #define BCMENET_DMA_MAXBURST 16 -+#define BCMENETSW_DMA_MAXBURST 8 - - /* tx transmit threshold (4 bytes unit), fifo is 256 bytes, the value - * must be low enough so that a DMA transfer of above burst length can -@@ -280,6 +281,9 @@ struct bcm_enet_priv { - /* number of dma desc in tx ring */ - int tx_ring_size; - -+ /* maximum dma burst size */ -+ int dma_maxburst; -+ - /* cpu view of rx dma ring */ - struct bcm_enet_desc *tx_desc_cpu; - diff --git a/target/linux/brcm63xx/patches-3.6/424-MIPS-BCM63XX-add-support-for-BCM6328-in-bcm_enetsw.patch b/target/linux/brcm63xx/patches-3.6/424-MIPS-BCM63XX-add-support-for-BCM6328-in-bcm_enetsw.patch deleted file mode 100644 index e665249c5e..0000000000 --- a/target/linux/brcm63xx/patches-3.6/424-MIPS-BCM63XX-add-support-for-BCM6328-in-bcm_enetsw.patch +++ /dev/null @@ -1,103 +0,0 @@ -From f1c1bfa89cdac76a215d0e21161da9f8f8373437 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 14 Jun 2011 21:14:39 +0200 -Subject: [PATCH 40/84] MIPS: BCM63XX: add support for BCM6328 in bcm_enetsw - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/clk.c | 34 ++++++++++++++----- - arch/mips/bcm63xx/dev-enet.c | 9 +++-- - .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 1 + - 3 files changed, 32 insertions(+), 12 deletions(-) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -118,21 +118,37 @@ static struct clk clk_ephy = { - */ - static void enetsw_set(struct clk *clk, int enable) - { -- if (!BCMCPU_IS_6368()) -+ u32 mask; -+ -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368()) - return; -- bcm_hwclock_set(CKCTL_6368_ROBOSW_EN | -- CKCTL_6368_SWPKT_USB_EN | -- CKCTL_6368_SWPKT_SAR_EN, enable); -+ -+ if (BCMCPU_IS_6328()) -+ mask = CKCTL_6328_ROBOSW_EN; -+ else -+ mask = CKCTL_6368_ROBOSW_EN | CKCTL_6368_SWPKT_USB_EN | -+ CKCTL_6368_SWPKT_SAR_EN; -+ -+ bcm_hwclock_set(mask, enable); - if (enable) { -+ u32 reg; - u32 val; - -+ if (BCMCPU_IS_6328()) { -+ reg = PERF_SOFTRESET_6328_REG; -+ mask = SOFTRESET_6328_ENETSW_MASK; -+ } else { -+ reg = PERF_SOFTRESET_6368_REG; -+ mask = SOFTRESET_6368_ENETSW_MASK; -+ } -+ - /* reset switch core afer clock change */ -- val = bcm_perf_readl(PERF_SOFTRESET_6368_REG); -- val &= ~SOFTRESET_6368_ENETSW_MASK; -- bcm_perf_writel(val, PERF_SOFTRESET_6368_REG); -+ val = bcm_perf_readl(reg); -+ val &= ~mask; -+ bcm_perf_writel(val, reg); - msleep(10); -- val |= SOFTRESET_6368_ENETSW_MASK; -- bcm_perf_writel(val, PERF_SOFTRESET_6368_REG); -+ val |= mask; -+ bcm_perf_writel(val, reg); - msleep(10); - } - } ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -141,7 +141,7 @@ static int __init register_shared(void) - shared_res[0].end = shared_res[0].start; - shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; - -- if (BCMCPU_IS_6368()) -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) - chan_count = 32; - else - chan_count = 16; -@@ -224,7 +224,7 @@ bcm63xx_enetsw_register(const struct bcm - { - int ret; - -- if (!BCMCPU_IS_6368()) -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368()) - return -ENODEV; - - ret = register_shared(); -@@ -241,7 +241,10 @@ bcm63xx_enetsw_register(const struct bcm - - memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof (*pd)); - -- enetsw_pd.num_ports = ENETSW_PORTS_6368; -+ if (BCMCPU_IS_6328()) -+ enetsw_pd.num_ports = ENETSW_PORTS_6328; -+ else if (BCMCPU_IS_6368()) -+ enetsw_pd.num_ports = ENETSW_PORTS_6368; - - ret = platform_device_register(&bcm63xx_enetsw_device); - if (ret) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -43,6 +43,7 @@ struct bcm63xx_enet_platform_data { - * on board ethernet switch platform data - */ - #define ENETSW_MAX_PORT 6 -+#define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */ - #define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */ - - #define ENETSW_RGMII_PORT0 4 diff --git a/target/linux/brcm63xx/patches-3.6/425-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch b/target/linux/brcm63xx/patches-3.6/425-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch deleted file mode 100644 index 51301d3675..0000000000 --- a/target/linux/brcm63xx/patches-3.6/425-MIPS-BCM63XX-add-HS-SPI-platform-device-and-register.patch +++ /dev/null @@ -1,128 +0,0 @@ -From 56be5a2d7e08faa7bb306faaf352ac4e6ac52c01 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sat, 12 Nov 2011 12:18:26 +0100 -Subject: [PATCH 26/60] MIPS: BCM63XX: add HS SPI platform device and register it - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/Makefile | 5 +- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 + - arch/mips/bcm63xx/dev-hsspi.c | 57 ++++++++++++++++++++ - .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h | 20 +++++++ - 4 files changed, 82 insertions(+), 2 deletions(-) - create mode 100644 arch/mips/bcm63xx/dev-hsspi.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,6 +1,7 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \ -- dev-dsp.o dev-enet.o dev-flash.o dev-pcmcia.o dev-rng.o \ -- dev-spi.o dev-uart.o dev-usb-ehci.o dev-usb-ohci.o dev-wdt.o -+ dev-dsp.o dev-enet.o dev-flash.o dev-hsspi.o dev-pcmcia.o \ -+ dev-rng.o dev-spi.o dev-uart.o dev-usb-ehci.o \ -+ dev-usb-ohci.o dev-wdt.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -25,6 +25,7 @@ - #include <bcm63xx_dev_enet.h> - #include <bcm63xx_dev_dsp.h> - #include <bcm63xx_dev_flash.h> -+#include <bcm63xx_dev_hsspi.h> - #include <bcm63xx_dev_pcmcia.h> - #include <bcm63xx_dev_spi.h> - #include <bcm63xx_dev_usb_ohci.h> -@@ -990,6 +991,7 @@ int __init board_register_devices(void) - pr_err(PFX "failed to register fallback SPROM\n"); - } - #endif -+ bcm63xx_hsspi_register(); - - bcm63xx_spi_register(); - ---- /dev/null -+++ b/arch/mips/bcm63xx/dev-hsspi.c -@@ -0,0 +1,57 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com> -+ */ -+ -+#include <linux/init.h> -+#include <linux/kernel.h> -+#include <linux/platform_device.h> -+ -+#include <bcm63xx_cpu.h> -+#include <bcm63xx_dev_hsspi.h> -+#include <bcm63xx_regs.h> -+ -+static struct resource spi_resources[] = { -+ { -+ .start = -1, /* filled at runtime */ -+ .end = -1, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ }, -+ { -+ .start = -1, /* filled at runtime */ -+ .flags = IORESOURCE_IRQ, -+ }, -+}; -+ -+static struct bcm63xx_hsspi_pdata spi_pdata = { -+ .bus_num = 0, -+}; -+ -+static struct platform_device bcm63xx_hsspi_device = { -+ .name = "bcm63xx-hsspi", -+ .id = 0, -+ .num_resources = ARRAY_SIZE(spi_resources), -+ .resource = spi_resources, -+ .dev = { -+ .platform_data = &spi_pdata, -+ }, -+}; -+ -+int __init bcm63xx_hsspi_register(void) -+{ -+ -+ if (!BCMCPU_IS_6328()) -+ return -ENODEV; -+ -+ spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI); -+ spi_resources[0].end = spi_resources[0].start; -+ spi_resources[0].end += RSET_HSSPI_SIZE - 1; -+ spi_resources[1].start = bcm63xx_get_irq_number(IRQ_HSSPI); -+ -+ spi_pdata.speed_hz = HSSPI_PLL_HZ_6328; -+ -+ return platform_device_register(&bcm63xx_hsspi_device); -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -@@ -0,0 +1,20 @@ -+#ifndef BCM63XX_DEV_HSSPI_H -+#define BCM63XX_DEV_HSSPI_H -+ -+#include <linux/types.h> -+#include <bcm63xx_io.h> -+#include <bcm63xx_regs.h> -+ -+int __init bcm63xx_hsspi_register(void); -+ -+struct bcm63xx_hsspi_pdata { -+ int bus_num; -+ u32 speed_hz; -+}; -+ -+#define bcm_hsspi_readl(o) bcm_rset_readl(RSET_HSSPI, (o)) -+#define bcm_hsspi_writel(v, o) bcm_rset_writel(RSET_HSSPI, (v), (o)) -+ -+#define HSSPI_PLL_HZ_6328 133333333 -+ -+#endif /* BCM63XX_DEV_HSSPI_H */ diff --git a/target/linux/brcm63xx/patches-3.6/426-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch b/target/linux/brcm63xx/patches-3.6/426-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch deleted file mode 100644 index 2b213968a1..0000000000 --- a/target/linux/brcm63xx/patches-3.6/426-SPI-MIPS-BCM63XX-Add-HS-SPI-driver.patch +++ /dev/null @@ -1,481 +0,0 @@ -From 4b27423676485d05bcd6fc6f3809164fb8f9d22d Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sat, 12 Nov 2011 12:19:55 +0100 -Subject: [PATCH 30/60] SPI: MIPS: BCM63XX: Add HSSPI driver - -Add a driver for the High Speed SPI controller found on newer BCM63XX SoCs. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h | 2 + - drivers/spi/Kconfig | 7 + - drivers/spi/Makefile | 1 + - drivers/spi/spi-bcm63xx-hsspi.c | 427 ++++++++++++++++++++ - 4 files changed, 437 insertions(+), 0 deletions(-) - create mode 100644 drivers/spi/spi-bcm63xx-hsspi.c - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -@@ -17,4 +17,6 @@ struct bcm63xx_hsspi_pdata { - - #define HSSPI_PLL_HZ_6328 133333333 - -+#define HSSPI_BUFFER_LEN 512 -+ - #endif /* BCM63XX_DEV_HSSPI_H */ ---- a/drivers/spi/Kconfig -+++ b/drivers/spi/Kconfig -@@ -100,6 +100,13 @@ config SPI_BCM63XX - help - Enable support for the SPI controller on the Broadcom BCM63xx SoCs. - -+config SPI_BCM63XX_HSSPI -+ tristate "Broadcom BCM63XX HS SPI controller driver" -+ depends on BCM63XX -+ help -+ This enables support for the High Speed SPI controller present on -+ newer Broadcom BCM63XX SoCs. -+ - config SPI_BITBANG - tristate "Utilities for Bitbanging SPI masters" - help ---- a/drivers/spi/Makefile -+++ b/drivers/spi/Makefile -@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o - obj-$(CONFIG_SPI_ATH79) += spi-ath79.o - obj-$(CONFIG_SPI_AU1550) += spi-au1550.o - obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o -+obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o - obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o - obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o - obj-$(CONFIG_SPI_BITBANG) += spi-bitbang.o ---- /dev/null -+++ b/drivers/spi/spi-bcm63xx-hsspi.c -@@ -0,0 +1,427 @@ -+/* -+ * Broadcom BCM63XX High Speed SPI Controller driver -+ * -+ * Copyright 2000-2010 Broadcom Corporation -+ * Copyright 2012 Jonas Gorski <jonas.gorski@gmail.com> -+ * -+ * Licensed under the GNU/GPL. See COPYING for details. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/io.h> -+#include <linux/clk.h> -+#include <linux/module.h> -+#include <linux/platform_device.h> -+#include <linux/delay.h> -+#include <linux/dma-mapping.h> -+#include <linux/err.h> -+#include <linux/interrupt.h> -+#include <linux/spi/spi.h> -+#include <linux/workqueue.h> -+ -+#include <bcm63xx_regs.h> -+#include <bcm63xx_dev_hsspi.h> -+ -+#define HSSPI_OP_CODE_SHIFT 13 -+#define HSSPI_OP_SLEEP (0 << HSSPI_OP_CODE_SHIFT) -+#define HSSPI_OP_READ_WRITE (1 << HSSPI_OP_CODE_SHIFT) -+#define HSSPI_OP_WRITE (2 << HSSPI_OP_CODE_SHIFT) -+#define HSSPI_OP_READ (3 << HSSPI_OP_CODE_SHIFT) -+ -+#define HSSPI_MAX_PREPEND_LEN 15 -+ -+#define HSSPI_MAX_SYNC_CLOCK 30000000 -+ -+struct bcm63xx_hsspi { -+ struct completion done; -+ struct spi_transfer *curr_trans; -+ -+ struct platform_device *pdev; -+ struct clk *clk; -+ void __iomem *regs; -+ u8 __iomem *fifo; -+ -+ u32 speed_hz; -+ int irq; -+}; -+ -+static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs, int hz, -+ int profile) -+{ -+ u32 reg; -+ -+ reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz)); -+ bcm_hsspi_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg, -+ HSSPI_PROFILE_CLK_CTRL_REG(profile)); -+ -+ reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(profile)); -+ if (hz > HSSPI_MAX_SYNC_CLOCK) -+ reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH; -+ else -+ reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH; -+ bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(profile)); -+} -+ -+static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, -+ struct spi_transfer *t1, -+ struct spi_transfer *t2) -+{ -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master); -+ u8 chip_select = spi->chip_select; -+ u16 opcode = 0; -+ int len, prepend_size = 0; -+ -+ init_completion(&bs->done); -+ -+ bs->curr_trans = t2 ? t2 : t1; -+ bcm63xx_hsspi_set_clk(bs, bs->curr_trans->speed_hz, chip_select); -+ -+ if (t2 && !t2->tx_buf) -+ prepend_size = t1->len; -+ -+ bcm_hsspi_writel(prepend_size << MODE_CTRL_PREPENDBYTE_CNT_SHIFT | -+ 2 << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT | -+ 2 << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT | 0xff, -+ HSSPI_PROFILE_MODE_CTRL_REG(chip_select)); -+ -+ if (t1->rx_buf && t1->tx_buf) -+ opcode = HSSPI_OP_READ_WRITE; -+ else if (t1->rx_buf || (t2 && t2->rx_buf)) -+ opcode = HSSPI_OP_READ; -+ else if (t1->tx_buf) -+ opcode = HSSPI_OP_WRITE; -+ -+ if (opcode == HSSPI_OP_READ && t2) -+ len = t2->len; -+ else -+ len = t1->len; -+ -+ if (t1->tx_buf) { -+ memcpy_toio(bs->fifo + 2, t1->tx_buf, t1->len); -+ if (t2 && t2->tx_buf) { -+ memcpy_toio(bs->fifo + 2 + t1->len, -+ t2->tx_buf, t2->len); -+ len += t2->len; -+ } -+ } -+ -+ opcode |= len; -+ memcpy_toio(bs->fifo, &opcode, sizeof(opcode)); -+ -+ /* enable interrupt */ -+ bcm_hsspi_writel(HSSPI_PING0_CMD_DONE, HSSPI_INT_MASK_REG); -+ -+ /* start the transfer */ -+ bcm_hsspi_writel(chip_select << PINGPONG_CMD_SS_SHIFT | -+ chip_select << PINGPONG_CMD_PROFILE_SHIFT | -+ PINGPONG_COMMAND_START_NOW, -+ HSSPI_PINGPONG_COMMAND_REG(0)); -+ -+ if (wait_for_completion_timeout(&bs->done, HZ) == 0) { -+ dev_err(&bs->pdev->dev, "transfer timed out!\n"); -+ return -ETIMEDOUT; -+ } -+ -+ return t1->len + (t2 ? t2->len : 0); -+} -+ -+static int bcm63xx_hsspi_setup(struct spi_device *spi) -+{ -+ u32 reg; -+ -+ if (spi->bits_per_word != 8) -+ return -EINVAL; -+ -+ if (spi->max_speed_hz == 0) -+ return -EINVAL; -+ -+ reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); -+ reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING); -+ if (spi->mode & SPI_CPHA) -+ reg |= SIGNAL_CTRL_LAUNCH_RISING; -+ else -+ reg |= SIGNAL_CTRL_LATCH_RISING; -+ bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); -+ -+ return 0; -+} -+ -+static int bcm63xx_hsspi_transfer_one(struct spi_master *master, -+ struct spi_message *msg) -+{ -+ struct spi_transfer *t, *prev = NULL; -+ struct spi_device *spi = msg->spi; -+ u32 reg; -+ int ret = -EINVAL; -+ int len = 0; -+ -+ /* check if we are able to make these transfers */ -+ list_for_each_entry(t, &msg->transfers, transfer_list) { -+ if (!t->tx_buf && !t->rx_buf) -+ goto out; -+ -+ if (t->speed_hz == 0) -+ t->speed_hz = spi->max_speed_hz; -+ -+ if (t->speed_hz > spi->max_speed_hz) -+ goto out; -+ -+ if (t->len > HSSPI_BUFFER_LEN) -+ goto out; -+ -+ /* -+ * This controller does not support keeping the chip select -+ * active between transfers. -+ * This logic currently supports combining: -+ * write then read with no cs_change (e.g. m25p80 RDSR) -+ * write then write with no cs_change (e.g. m25p80 PP) -+ */ -+ if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) { -+ /* -+ * reject if we have to combine two tx transfers and -+ * their combined length is bigger than the buffer -+ */ -+ if (prev->tx_buf && t->tx_buf && -+ (prev->len + t->len) > HSSPI_BUFFER_LEN) -+ goto out; -+ /* -+ * reject if we need write more than 15 bytes in read -+ * then write. -+ */ -+ if (prev->tx_buf && t->rx_buf && -+ prev->len > HSSPI_MAX_PREPEND_LEN) -+ goto out; -+ } -+ -+ } -+ -+ /* setup clock polarity */ -+ reg = bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG); -+ reg &= ~GLOBAL_CTRL_CLK_POLARITY; -+ if (spi->mode & SPI_CPOL) -+ reg |= GLOBAL_CTRL_CLK_POLARITY; -+ bcm_hsspi_writel(reg, HSSPI_GLOBAL_CTRL_REG); -+ -+ list_for_each_entry(t, &msg->transfers, transfer_list) { -+ if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) { -+ /* combine write with following transfer */ -+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, t); -+ if (ret < 0) -+ goto out; -+ -+ len += ret; -+ prev = NULL; -+ continue; -+ } -+ -+ /* write the previous pending transfer */ -+ if (prev != NULL) { -+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL); -+ if (ret < 0) -+ goto out; -+ -+ len += ret; -+ } -+ -+ prev = t; -+ } -+ -+ /* do last pending transfer */ -+ if (prev != NULL) { -+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL); -+ if (ret < 0) -+ goto out; -+ len += ret; -+ } -+ -+ msg->actual_length = len; -+ ret = 0; -+out: -+ msg->status = ret; -+ spi_finalize_current_message(master); -+ return 0; -+} -+ -+static irqreturn_t bcm63xx_hsspi_interrupt(int irq, void *dev_id) -+{ -+ struct spi_master *master = (struct spi_master *)dev_id; -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ if (bcm_hsspi_readl(HSSPI_INT_STATUS_MASKED_REG) == 0) -+ return IRQ_NONE; -+ -+ bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG); -+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG); -+ -+ if (bs->curr_trans && bs->curr_trans->rx_buf) -+ memcpy_fromio(bs->curr_trans->rx_buf, bs->fifo, -+ bs->curr_trans->len); -+ complete(&bs->done); -+ -+ return IRQ_HANDLED; -+} -+ -+static int __devinit bcm63xx_hsspi_probe(struct platform_device *pdev) -+{ -+ -+ struct spi_master *master; -+ struct bcm63xx_hsspi *bs; -+ struct resource *res_mem; -+ void __iomem *regs; -+ struct device *dev = &pdev->dev; -+ struct bcm63xx_hsspi_pdata *pdata = pdev->dev.platform_data; -+ struct clk *clk; -+ int irq; -+ int ret; -+ -+ irq = platform_get_irq(pdev, 0); -+ if (irq < 0) { -+ dev_err(dev, "no irq\n"); -+ return -ENXIO; -+ } -+ -+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ regs = devm_request_and_ioremap(dev, res_mem); -+ if (!regs) { -+ dev_err(dev, "unable to ioremap regs\n"); -+ return -ENXIO; -+ } -+ -+ clk = clk_get(dev, "hsspi"); -+ -+ if (IS_ERR(clk)) { -+ ret = PTR_ERR(clk); -+ goto out_release; -+ } -+ -+ clk_prepare_enable(clk); -+ -+ master = spi_alloc_master(&pdev->dev, sizeof(*bs)); -+ if (!master) { -+ ret = -ENOMEM; -+ goto out_disable_clk; -+ } -+ -+ bs = spi_master_get_devdata(master); -+ bs->pdev = pdev; -+ bs->clk = clk; -+ bs->regs = regs; -+ -+ master->bus_num = pdata->bus_num; -+ master->num_chipselect = 8; -+ master->setup = bcm63xx_hsspi_setup; -+ master->transfer_one_message = bcm63xx_hsspi_transfer_one; -+ master->mode_bits = SPI_CPOL | SPI_CPHA; -+ -+ bs->speed_hz = pdata->speed_hz; -+ bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0)); -+ -+ platform_set_drvdata(pdev, master); -+ -+ bs->curr_trans = NULL; -+ -+ /* Initialize the hardware */ -+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG); -+ -+ /* clean up any pending interrupts */ -+ bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG); -+ -+ bcm_hsspi_writel(bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG) | -+ GLOBAL_CTRL_CLK_GATE_SSOFF, -+ HSSPI_GLOBAL_CTRL_REG); -+ -+ ret = devm_request_irq(dev, irq, bcm63xx_hsspi_interrupt, IRQF_SHARED, -+ pdev->name, master); -+ -+ if (ret) -+ goto out_put_master; -+ -+ /* register and we are done */ -+ ret = spi_register_master(master); -+ if (ret) -+ goto out_free_irq; -+ -+ return 0; -+ -+out_free_irq: -+ devm_free_irq(dev, bs->irq, master); -+out_put_master: -+ spi_master_put(master); -+out_disable_clk: -+ clk_disable_unprepare(clk); -+ clk_put(clk); -+out_release: -+ devm_ioremap_release(dev, regs); -+ -+ return ret; -+} -+ -+ -+static int __exit bcm63xx_hsspi_remove(struct platform_device *pdev) -+{ -+ struct spi_master *master = platform_get_drvdata(pdev); -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ spi_unregister_master(master); -+ -+ /* reset the hardware and block queue progress */ -+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG); -+ clk_disable_unprepare(bs->clk); -+ clk_put(bs->clk); -+ -+ return 0; -+} -+ -+#ifdef CONFIG_PM -+static int bcm63xx_hsspi_suspend(struct platform_device *pdev, -+ pm_message_t mesg) -+{ -+ struct spi_master *master = platform_get_drvdata(pdev); -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ spi_master_suspend(master); -+ clk_disable(bs->clk); -+ -+ return 0; -+} -+ -+static int bcm63xx_hsspi_resume(struct platform_device *pdev) -+{ -+ struct spi_master *master = platform_get_drvdata(pdev); -+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master); -+ -+ clk_enable(bs->clk); -+ spi_master_resume(master); -+ -+ return 0; -+} -+ -+static const struct dev_pm_ops bcm63xx_hsspi_pm_ops = { -+ .suspend = bcm63xx_hsspi_suspend, -+ .resume = bcm63xx_hsspi_resume, -+}; -+ -+#define BCM63XX_HSSPI_PM_OPS (&bcm63xx_hsspi_pm_ops) -+#else -+#define BCM63XX_HSSPI_PM_OPS NULL -+#endif -+ -+ -+ -+static struct platform_driver bcm63xx_hsspi_driver = { -+ .driver = { -+ .name = "bcm63xx-hsspi", -+ .owner = THIS_MODULE, -+ .pm = BCM63XX_HSSPI_PM_OPS, -+ }, -+ .probe = bcm63xx_hsspi_probe, -+ .remove = __exit_p(bcm63xx_hsspi_remove), -+}; -+ -+module_platform_driver(bcm63xx_hsspi_driver); -+ -+MODULE_ALIAS("platform:bcm63xx_hsspi"); -+MODULE_DESCRIPTION("Broadcom BCM63xx HS SPI Controller driver"); -+MODULE_AUTHOR("Jonas Gorski <jonas.gorski@gmail.com>"); -+MODULE_LICENSE("GPL"); diff --git a/target/linux/brcm63xx/patches-3.6/427-MIPS-BCM63XX-Register-SPI-flash-if-present.patch b/target/linux/brcm63xx/patches-3.6/427-MIPS-BCM63XX-Register-SPI-flash-if-present.patch deleted file mode 100644 index 14776af760..0000000000 --- a/target/linux/brcm63xx/patches-3.6/427-MIPS-BCM63XX-Register-SPI-flash-if-present.patch +++ /dev/null @@ -1,102 +0,0 @@ -From d135d94b3d1fe599d13e7198d5f502912d694c13 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 3 Jul 2011 15:00:38 +0200 -Subject: [PATCH 29/60] MIPS: BCM63XX: Register SPI flash if present - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/dev-flash.c | 33 +++++++++++++++++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 2 + - 2 files changed, 33 insertions(+), 2 deletions(-) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -16,9 +16,12 @@ - #include <linux/mtd/mtd.h> - #include <linux/mtd/partitions.h> - #include <linux/mtd/physmap.h> -+#include <linux/spi/spi.h> -+#include <linux/spi/flash.h> - - #include <bcm63xx_cpu.h> - #include <bcm63xx_dev_flash.h> -+#include <bcm63xx_dev_hsspi.h> - #include <bcm63xx_regs.h> - #include <bcm63xx_io.h> - -@@ -55,6 +58,21 @@ static struct platform_device mtd_dev = - }, - }; - -+static struct flash_platform_data bcm63xx_flash_data = { -+ .part_probe_types = bcm63xx_part_types, -+}; -+ -+static struct spi_board_info bcm63xx_spi_flash_info[] = { -+ { -+ .bus_num = 0, -+ .chip_select = 0, -+ .mode = 0, -+ .max_speed_hz = 781000, -+ .modalias = "m25p80", -+ .platform_data = &bcm63xx_flash_data, -+ }, -+}; -+ - static int __init bcm63xx_detect_flash_type(void) - { - u32 val; -@@ -62,6 +80,11 @@ static int __init bcm63xx_detect_flash_t - switch (bcm63xx_get_cpu_id()) { - case BCM6328_CPU_ID: - val = bcm_misc_readl(MISC_STRAPBUS_6328_REG); -+ if (val & STRAPBUS_6328_HSSPI_CLK_FAST) -+ bcm63xx_spi_flash_info[0].max_speed_hz = 33333334; -+ else -+ bcm63xx_spi_flash_info[0].max_speed_hz = 16666667; -+ - if (val & STRAPBUS_6328_BOOT_SEL_SERIAL) - return BCM63XX_FLASH_TYPE_SERIAL; - else -@@ -79,6 +102,9 @@ static int __init bcm63xx_detect_flash_t - return BCM63XX_FLASH_TYPE_SERIAL; - case BCM6368_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); -+ if (val & STRAPBUS_6368_SPI_CLK_FAST) -+ bcm63xx_spi_flash_info[0].max_speed_hz = 20000000; -+ - switch (val & STRAPBUS_6368_BOOT_SEL_MASK) { - case STRAPBUS_6368_BOOT_SEL_NAND: - return BCM63XX_FLASH_TYPE_NAND; -@@ -110,8 +136,11 @@ int __init bcm63xx_flash_register(void) - - return platform_device_register(&mtd_dev); - case BCM63XX_FLASH_TYPE_SERIAL: -- pr_warn("unsupported serial flash detected\n"); -- return -ENODEV; -+ if (BCMCPU_IS_6328()) -+ bcm63xx_flash_data.max_transfer_len = HSSPI_BUFFER_LEN; -+ -+ return spi_register_board_info(bcm63xx_spi_flash_info, -+ ARRAY_SIZE(bcm63xx_spi_flash_info)); - case BCM63XX_FLASH_TYPE_NAND: - pr_warn("unsupported NAND flash detected\n"); - return -ENODEV; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -614,6 +614,7 @@ - #define GPIO_STRAPBUS_REG 0x40 - #define STRAPBUS_6358_BOOT_SEL_PARALLEL (1 << 1) - #define STRAPBUS_6358_BOOT_SEL_SERIAL (0 << 1) -+#define STRAPBUS_6368_SPI_CLK_FAST (1 << 6) - #define STRAPBUS_6368_BOOT_SEL_MASK 0x3 - #define STRAPBUS_6368_BOOT_SEL_NAND 0 - #define STRAPBUS_6368_BOOT_SEL_SERIAL 1 -@@ -1308,6 +1309,7 @@ - #define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15) - - #define MISC_STRAPBUS_6328_REG 0x240 -+#define STRAPBUS_6328_HSSPI_CLK_FAST (1 << 4) - #define STRAPBUS_6328_FCVO_SHIFT 7 - #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT) - #define STRAPBUS_6328_BOOT_SEL_SERIAL (1 << 28) diff --git a/target/linux/brcm63xx/patches-3.6/428-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.6/428-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch deleted file mode 100644 index 98a229b1ac..0000000000 --- a/target/linux/brcm63xx/patches-3.6/428-MIPS-BCM63XX-add-flash-detection-for-BCM6362.patch +++ /dev/null @@ -1,50 +0,0 @@ -From d9666553a10ea85ea64e3e8784a42167a1709ed5 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Mon, 21 Nov 2011 00:48:52 +0100 -Subject: [PATCH 55/84] MIPS: BCM63XX: add flash detection for BCM6362 - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/dev-flash.c | 13 ++++++++++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 1 + - 2 files changed, 13 insertions(+), 1 deletions(-) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -100,6 +100,17 @@ static int __init bcm63xx_detect_flash_t - return BCM63XX_FLASH_TYPE_PARALLEL; - else - return BCM63XX_FLASH_TYPE_SERIAL; -+ case BCM6362_CPU_ID: -+ val = bcm_misc_readl(MISC_STRAPBUS_6362_REG); -+ if (val & STRAPBUS_6362_HSSPI_CLK_FAST) -+ bcm63xx_spi_flash_info[0].max_speed_hz = 50000000; -+ else -+ bcm63xx_spi_flash_info[0].max_speed_hz = 20000000; -+ -+ if (val & STRAPBUS_6362_BOOT_SEL_SERIAL) -+ return BCM63XX_FLASH_TYPE_SERIAL; -+ else -+ return BCM63XX_FLASH_TYPE_NAND; - case BCM6368_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); - if (val & STRAPBUS_6368_SPI_CLK_FAST) -@@ -136,7 +147,7 @@ int __init bcm63xx_flash_register(void) - - return platform_device_register(&mtd_dev); - case BCM63XX_FLASH_TYPE_SERIAL: -- if (BCMCPU_IS_6328()) -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) - bcm63xx_flash_data.max_transfer_len = HSSPI_BUFFER_LEN; - - return spi_register_board_info(bcm63xx_spi_flash_info, ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1304,6 +1304,7 @@ - - #define MISC_STRAPBUS_6362_REG 0x14 - #define STRAPBUS_6362_FCVO_SHIFT 1 -+#define STRAPBUS_6362_HSSPI_CLK_FAST (1 << 13) - #define STRAPBUS_6362_FCVO_MASK (0x1f << STRAPBUS_6362_FCVO_SHIFT) - #define STRAPBUS_6362_BOOT_SEL_SERIAL (1 << 15) - #define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15) diff --git a/target/linux/brcm63xx/patches-3.6/428-MIPS-BCM63XX-move-nvram-related-functions-into-their.patch b/target/linux/brcm63xx/patches-3.6/428-MIPS-BCM63XX-move-nvram-related-functions-into-their.patch deleted file mode 100644 index f7f4e90377..0000000000 --- a/target/linux/brcm63xx/patches-3.6/428-MIPS-BCM63XX-move-nvram-related-functions-into-their.patch +++ /dev/null @@ -1,351 +0,0 @@ -From 5b753c1d01c6af23d7d37d37d9de30da8a971084 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sat, 12 May 2012 22:51:08 +0200 -Subject: [PATCH 60/79] MIPS: BCM63XX: move nvram related functions into their - own file - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/Makefile | 6 +- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 74 +++-------------- - arch/mips/bcm63xx/nvram.c | 84 ++++++++++++++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h | 34 ++++++++ - .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 17 ---- - 5 files changed, 134 insertions(+), 81 deletions(-) - create mode 100644 arch/mips/bcm63xx/nvram.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,6 +1,6 @@ --obj-y += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \ -- dev-dsp.o dev-enet.o dev-flash.o dev-hsspi.o dev-pcmcia.o \ -- dev-rng.o dev-spi.o dev-uart.o dev-usb-ehci.o \ -+obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o setup.o \ -+ timer.o dev-dsp.o dev-enet.o dev-flash.o dev-hsspi.o \ -+ dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-usb-ehci.o \ - dev-usb-ohci.o dev-wdt.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -21,6 +21,7 @@ - #include <bcm63xx_dev_uart.h> - #include <bcm63xx_regs.h> - #include <bcm63xx_io.h> -+#include <bcm63xx_nvram.h> - #include <bcm63xx_dev_pci.h> - #include <bcm63xx_dev_enet.h> - #include <bcm63xx_dev_dsp.h> -@@ -41,8 +42,6 @@ - #define CFE_OFFSET_64K 0x10000 - #define CFE_OFFSET_128K 0x20000 - --static struct bcm963xx_nvram nvram; --static unsigned int mac_addr_used; - static struct board_info board; - - /* -@@ -741,50 +740,16 @@ const char *board_get_name(void) - return board.name; - } - --/* -- * register & return a new board mac address -- */ --static int board_get_mac_address(u8 *mac) --{ -- u8 *p; -- int count; -- -- if (mac_addr_used >= nvram.mac_addr_count) { -- printk(KERN_ERR PFX "not enough mac address\n"); -- return -ENODEV; -- } -- -- memcpy(mac, nvram.mac_addr_base, ETH_ALEN); -- p = mac + ETH_ALEN - 1; -- count = mac_addr_used; -- -- while (count--) { -- do { -- (*p)++; -- if (*p != 0) -- break; -- p--; -- } while (p != mac); -- } -- -- if (p == mac) { -- printk(KERN_ERR PFX "unable to fetch mac address\n"); -- return -ENODEV; -- } -- -- mac_addr_used++; -- return 0; --} -- - static void __init boardid_fixup(u8 *boot_addr) - { - struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K); -+ char *board_name = (char *)bcm63xx_nvram_get_name(); - - /* check if bcm_tag is at 64k offset */ -- if (strncmp(nvram.name, tag->board_id, BOARDID_LEN) != 0) { -+ if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { - /* else try 128k */ - tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K); -- if (strncmp(nvram.name, tag->board_id, BOARDID_LEN) != 0) { -+ if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { - /* No tag found */ - printk(KERN_DEBUG "No bcm_tag found!\n"); - return; -@@ -794,9 +759,9 @@ static void __init boardid_fixup(u8 *boo - if (tag->information1[0] != '+') - return; - -- strncpy(nvram.name, &tag->information1[1], BOARDID_LEN); -+ strncpy(board_name, &tag->information1[1], BOARDID_LEN); - -- printk(KERN_INFO "Overriding boardid with '%s'\n", nvram.name); -+ printk(KERN_INFO "Overriding boardid with '%s'\n", board_name); - } - - /* -@@ -804,9 +769,10 @@ static void __init boardid_fixup(u8 *boo - */ - void __init board_prom_init(void) - { -- unsigned int check_len, i; -- u8 *boot_addr, *cfe, *p; -+ unsigned int i; -+ u8 *boot_addr, *cfe; - char cfe_version[32]; -+ char *board_name; - u32 val; - - /* read base address of boot chip select (0) -@@ -831,32 +797,19 @@ void __init board_prom_init(void) - strcpy(cfe_version, "unknown"); - printk(KERN_INFO PFX "CFE version: %s\n", cfe_version); - -- /* extract nvram data */ -- memcpy(&nvram, boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram)); -- -- /* check checksum before using data */ -- if (nvram.version <= 4) -- check_len = offsetof(struct bcm963xx_nvram, checksum_old); -- else -- check_len = sizeof(nvram); -- val = 0; -- p = (u8 *)&nvram; -- while (check_len--) -- val += *p; -- if (val) { -- printk(KERN_ERR PFX "invalid nvram checksum\n"); -+ if (bcm63xx_nvram_init(boot_addr + BCM963XX_NVRAM_OFFSET)) - return; -- } - - if (strcmp(cfe_version, "unknown") != 0) { - /* cfe present */ - boardid_fixup(boot_addr); - } - -+ board_name = bcm63xx_nvram_get_name(); - /* find board by name */ - for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) { -- if (strncmp(nvram.name, bcm963xx_boards[i]->name, -- sizeof(nvram.name))) -+ if (strncmp(board_name, bcm963xx_boards[i]->name, -+ BCM63XX_NVRAM_NAMELEN)) - continue; - /* copy, board desc array is marked initdata */ - memcpy(&board, bcm963xx_boards[i], sizeof(board)); -@@ -866,7 +819,7 @@ void __init board_prom_init(void) - /* bail out if board is not found, will complain later */ - if (!board.name[0]) { - char name[17]; -- memcpy(name, nvram.name, 16); -+ memcpy(name, board_name, 16); - name[16] = 0; - printk(KERN_ERR PFX "unknown bcm963xx board: %s\n", - name); -@@ -959,15 +912,15 @@ int __init board_register_devices(void) - bcm63xx_pcmcia_register(); - - if (board.has_enet0 && -- !board_get_mac_address(board.enet0.mac_addr)) -+ !bcm63xx_nvram_get_mac_address(board.enet0.mac_addr)) - bcm63xx_enet_register(0, &board.enet0); - - if (board.has_enet1 && -- !board_get_mac_address(board.enet1.mac_addr)) -+ !bcm63xx_nvram_get_mac_address(board.enet1.mac_addr)) - bcm63xx_enet_register(1, &board.enet1); - - if (board.has_enetsw && -- !board_get_mac_address(board.enetsw.mac_addr)) -+ !bcm63xx_nvram_get_mac_address(board.enetsw.mac_addr)) - bcm63xx_enetsw_register(&board.enetsw); - - if (board.has_ehci0) -@@ -983,7 +936,7 @@ int __init board_register_devices(void) - * do this after registering enet devices - */ - #ifdef CONFIG_SSB_PCIHOST -- if (!board_get_mac_address(bcm63xx_sprom.il0mac)) { -+ if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { - memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN); - memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN); - if (ssb_arch_register_fallback_sprom( ---- /dev/null -+++ b/arch/mips/bcm63xx/nvram.c -@@ -0,0 +1,84 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com> -+ */ -+ -+#define pr_fmt(fmt) "bcm63xx_nvram: " fmt -+ -+#include <linux/init.h> -+#include <linux/export.h> -+#include <linux/kernel.h> -+ -+#include <bcm63xx_nvram.h> -+ -+static struct bcm963xx_nvram nvram; -+static int mac_addr_used; -+ -+int __init bcm63xx_nvram_init(void *addr) -+{ -+ unsigned int check_len; -+ u8 *p; -+ u32 val; -+ -+ /* extract nvram data */ -+ memcpy(&nvram, addr, sizeof(nvram)); -+ -+ /* check checksum before using data */ -+ if (nvram.version <= 4) -+ check_len = offsetof(struct bcm963xx_nvram, checksum_old); -+ else -+ check_len = sizeof(nvram); -+ val = 0; -+ p = (u8 *)&nvram; -+ -+ while (check_len--) -+ val += *p; -+ if (val) { -+ pr_err("invalid nvram checksum\n"); -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+u8 *bcm63xx_nvram_get_name(void) -+{ -+ return nvram.name; -+} -+EXPORT_SYMBOL(bcm63xx_nvram_get_name); -+ -+int bcm63xx_nvram_get_mac_address(u8 *mac) -+{ -+ u8 *p; -+ int count; -+ -+ if (mac_addr_used >= nvram.mac_addr_count) { -+ pr_err("not enough mac address\n"); -+ return -ENODEV; -+ } -+ -+ memcpy(mac, nvram.mac_addr_base, ETH_ALEN); -+ p = mac + ETH_ALEN - 1; -+ count = mac_addr_used; -+ -+ while (count--) { -+ do { -+ (*p)++; -+ if (*p != 0) -+ break; -+ p--; -+ } while (p != mac); -+ } -+ -+ if (p == mac) { -+ pr_err("unable to fetch mac address\n"); -+ return -ENODEV; -+ } -+ -+ mac_addr_used++; -+ return 0; -+} -+EXPORT_SYMBOL(bcm63xx_nvram_get_mac_address); ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h -@@ -0,0 +1,34 @@ -+#ifndef BCM63XX_NVRAM_H -+#define BCM63XX_NVRAM_H -+ -+#include <linux/if_ether.h> -+ -+#define BCM63XX_NVRAM_NAMELEN 16 -+ -+/* -+ * nvram structure -+ */ -+struct bcm963xx_nvram { -+ u32 version; -+ u8 reserved1[256]; -+ u8 name[BCM63XX_NVRAM_NAMELEN]; -+ u32 main_tp_number; -+ u32 psi_size; -+ u32 mac_addr_count; -+ u8 mac_addr_base[ETH_ALEN]; -+ u8 reserved2[2]; -+ u32 checksum_old; -+ u8 reserved3[720]; -+ u32 checksum_high; -+}; -+ -+int __init bcm63xx_nvram_init(void *); -+ -+u8 *bcm63xx_nvram_get_name(void); -+ -+/* -+ * register & return a new board mac address -+ */ -+int bcm63xx_nvram_get_mac_address(u8 *mac); -+ -+#endif /* BCM63XX_NVRAM_H */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -15,23 +15,6 @@ - #define BCM963XX_NVRAM_OFFSET 0x580 - - /* -- * nvram structure -- */ --struct bcm963xx_nvram { -- u32 version; -- u8 reserved1[256]; -- u8 name[16]; -- u32 main_tp_number; -- u32 psi_size; -- u32 mac_addr_count; -- u8 mac_addr_base[6]; -- u8 reserved2[2]; -- u32 checksum_old; -- u8 reserved3[720]; -- u32 checksum_high; --}; -- --/* - * board definition - */ - struct board_info { diff --git a/target/linux/brcm63xx/patches-3.6/429-MIPS-BCM63XX-export-PSI-size-from-nvram.patch b/target/linux/brcm63xx/patches-3.6/429-MIPS-BCM63XX-export-PSI-size-from-nvram.patch deleted file mode 100644 index 34966b27f1..0000000000 --- a/target/linux/brcm63xx/patches-3.6/429-MIPS-BCM63XX-export-PSI-size-from-nvram.patch +++ /dev/null @@ -1,44 +0,0 @@ -From ffbeb183bf0e9e12fd607c5352f48420c32f588f Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sat, 12 May 2012 23:04:17 +0200 -Subject: [PATCH 61/79] MIPS: BCM63XX: export PSI size from nvram - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/nvram.c | 11 +++++++++++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h | 2 ++ - 2 files changed, 13 insertions(+) - ---- a/arch/mips/bcm63xx/nvram.c -+++ b/arch/mips/bcm63xx/nvram.c -@@ -14,6 +14,8 @@ - - #include <bcm63xx_nvram.h> - -+#define BCM63XX_DEFAULT_PSI_SIZE 64 -+ - static struct bcm963xx_nvram nvram; - static int mac_addr_used; - -@@ -82,3 +84,12 @@ int bcm63xx_nvram_get_mac_address(u8 *ma - return 0; - } - EXPORT_SYMBOL(bcm63xx_nvram_get_mac_address); -+ -+int bcm63xx_nvram_get_psi_size(void) -+{ -+ if (nvram.psi_size > 0) -+ return nvram.psi_size; -+ -+ return BCM63XX_DEFAULT_PSI_SIZE; -+} -+EXPORT_SYMBOL(bcm63xx_nvram_get_psi_size); ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h -@@ -31,4 +31,6 @@ u8 *bcm63xx_nvram_get_name(void); - */ - int bcm63xx_nvram_get_mac_address(u8 *mac); - -+int bcm63xx_nvram_get_psi_size(void); -+ - #endif /* BCM63XX_NVRAM_H */ diff --git a/target/linux/brcm63xx/patches-3.6/430-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch b/target/linux/brcm63xx/patches-3.6/430-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch deleted file mode 100644 index fd1bfc4b8c..0000000000 --- a/target/linux/brcm63xx/patches-3.6/430-MTD-bcm63xxpart-use-nvram-for-PSI-size.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 658afad639a9456e1bb6fe5bba0032f3c0c3f699 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 1 May 2012 14:10:39 +0200 -Subject: [PATCH 62/79] MTD: bcm63xxpart: use nvram for PSI size - ---- - drivers/mtd/bcm63xxpart.c | 4 +++- - 1 file changed, 3 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -32,6 +32,7 @@ - #include <linux/mtd/mtd.h> - #include <linux/mtd/partitions.h> - -+#include <asm/mach-bcm63xx/bcm63xx_nvram.h> - #include <linux/bcm963xx_tag.h> - #include <asm/mach-bcm63xx/board_bcm963xx.h> - -@@ -90,7 +91,8 @@ static int bcm63xx_parse_cfe_partitions( - BCM63XX_CFE_BLOCK_SIZE); - - cfelen = cfe_erasesize; -- nvramlen = cfe_erasesize; -+ nvramlen = bcm63xx_nvram_get_psi_size() * 1024; -+ nvramlen = roundup(nvramlen, cfe_erasesize); - - /* Allocate memory for buffer */ - buf = vmalloc(sizeof(struct bcm_tag)); diff --git a/target/linux/brcm63xx/patches-3.6/431-MTD-physmap-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-3.6/431-MTD-physmap-allow-passing-pp_data.patch deleted file mode 100644 index de2216ab92..0000000000 --- a/target/linux/brcm63xx/patches-3.6/431-MTD-physmap-allow-passing-pp_data.patch +++ /dev/null @@ -1,41 +0,0 @@ -From 266c506f4b262bd6aba0776a03d82c98e65d9906 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 1 May 2012 17:32:36 +0200 -Subject: [PATCH 63/79] MTD: physmap: allow passing pp_data - ---- - drivers/mtd/maps/physmap.c | 4 +++- - include/linux/mtd/physmap.h | 1 + - 2 files changed, 4 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/maps/physmap.c -+++ b/drivers/mtd/maps/physmap.c -@@ -100,6 +100,7 @@ static int physmap_flash_probe(struct pl - { - struct physmap_flash_data *physmap_data; - struct physmap_flash_info *info; -+ struct mtd_part_parser_data *pp_data; - const char **probe_type; - const char **part_types; - int err = 0; -@@ -191,8 +192,9 @@ static int physmap_flash_probe(struct pl - spin_lock_init(&info->vpp_lock); - - part_types = physmap_data->part_probe_types ? : part_probe_types; -+ pp_data = physmap_data->pp_data ? physmap_data->pp_data : NULL; - -- mtd_device_parse_register(info->cmtd, part_types, NULL, -+ mtd_device_parse_register(info->cmtd, part_types, pp_data, - physmap_data->parts, physmap_data->nr_parts); - return 0; - ---- a/include/linux/mtd/physmap.h -+++ b/include/linux/mtd/physmap.h -@@ -32,6 +32,7 @@ struct physmap_flash_data { - char *probe_type; - struct mtd_partition *parts; - const char **part_probe_types; -+ struct mtd_part_parser_data *pp_data; - }; - - #endif /* __LINUX_MTD_PHYSMAP__ */ diff --git a/target/linux/brcm63xx/patches-3.6/432-BCM63XX-allow-providing-fixup-data-in-board-data.patch b/target/linux/brcm63xx/patches-3.6/432-BCM63XX-allow-providing-fixup-data-in-board-data.patch deleted file mode 100644 index 5d35cbfdfb..0000000000 --- a/target/linux/brcm63xx/patches-3.6/432-BCM63XX-allow-providing-fixup-data-in-board-data.patch +++ /dev/null @@ -1,81 +0,0 @@ -From 5131195413b62df73dfd394fea272830ea8c4e1a Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 3 May 2012 14:40:03 +0200 -Subject: [PATCH 67/80] BCM63XX: allow providing fixup data in board data - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 10 +++++++++- - arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 10 ++++++++++ - 2 files changed, 19 insertions(+), 1 deletion(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -33,6 +33,7 @@ - #include <bcm63xx_dev_usb_ehci.h> - #include <board_bcm963xx.h> - #include <linux/bcm963xx_tag.h> -+#include <pci_ath9k_fixup.h> - - #define PFX "board_bcm963xx: " - -@@ -901,6 +902,7 @@ int __init board_register_devices(void) - { - int button_count = 0; - int led_count = 0; -+ int i; - - if (board.has_uart0) - bcm63xx_uart_register(0); -@@ -936,7 +938,8 @@ int __init board_register_devices(void) - * do this after registering enet devices - */ - #ifdef CONFIG_SSB_PCIHOST -- if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { -+ if (!board.has_caldata && -+ !bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { - memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN); - memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN); - if (ssb_arch_register_fallback_sprom( -@@ -978,5 +981,9 @@ int __init board_register_devices(void) - platform_device_register(&bcm63xx_gpio_keys_device); - } - -+ /* register any fixups */ -+ for (i = 0; i < board.has_caldata; i++) -+ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset); -+ - return 0; - } ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -7,6 +7,7 @@ - #include <linux/leds.h> - #include <bcm63xx_dev_enet.h> - #include <bcm63xx_dev_dsp.h> -+#include <pci_ath9k_fixup.h> - - /* - * flash mapping -@@ -14,6 +15,11 @@ - #define BCM963XX_CFE_VERSION_OFFSET 0x570 - #define BCM963XX_NVRAM_OFFSET 0x580 - -+struct ath9k_caldata { -+ unsigned int slot; -+ u32 caldata_offset; -+}; -+ - /* - * board definition - */ -@@ -32,6 +38,10 @@ struct board_info { - unsigned int has_dsp:1; - unsigned int has_uart0:1; - unsigned int has_uart1:1; -+ unsigned int has_caldata:2; -+ -+ /* wifi calibration data config */ -+ struct ath9k_caldata caldata[2]; - - /* ethernet config */ - struct bcm63xx_enet_platform_data enet0; diff --git a/target/linux/brcm63xx/patches-3.6/433-MTD-m25p80-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-3.6/433-MTD-m25p80-allow-passing-pp_data.patch deleted file mode 100644 index 75e58896ed..0000000000 --- a/target/linux/brcm63xx/patches-3.6/433-MTD-m25p80-allow-passing-pp_data.patch +++ /dev/null @@ -1,40 +0,0 @@ -From 7f17dfe9009beb07a3de0e380932a725293829df Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 1 May 2012 17:33:03 +0200 -Subject: [PATCH 64/79] MTD: m25p80: allow passing pp_data - ---- - drivers/mtd/devices/m25p80.c | 3 +++ - include/linux/spi/flash.h | 2 ++ - 2 files changed, 5 insertions(+) - ---- a/drivers/mtd/devices/m25p80.c -+++ b/drivers/mtd/devices/m25p80.c -@@ -861,6 +861,9 @@ static int __devinit m25p_probe(struct s - dev_warn(&spi->dev, "unrecognized id %s\n", data->type); - } - -+ if (data && data->pp_data) -+ memcpy(&ppdata, data->pp_data, sizeof(ppdata)); -+ - info = (void *)id->driver_data; - - if (info->jedec_id) { ---- a/include/linux/spi/flash.h -+++ b/include/linux/spi/flash.h -@@ -12,6 +12,7 @@ struct mtd_part_parser_data; - * with chips that can't be queried for JEDEC or other IDs - * @part_probe_types: optional list of MTD parser names to use for - * partitioning -+ * @pp_data: optional partition parser data. - * - * @max_transfer_len: option maximum read/write length limitation for - * SPI controllers not able to transfer any length commands. -@@ -30,6 +31,7 @@ struct flash_platform_data { - char *type; - - const char **part_probe_types; -+ struct mtd_part_parser_data *pp_data; - - unsigned int max_transfer_len; - /* we'll likely add more ... use JEDEC IDs, etc */ diff --git a/target/linux/brcm63xx/patches-3.6/434-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch b/target/linux/brcm63xx/patches-3.6/434-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch deleted file mode 100644 index 7035098202..0000000000 --- a/target/linux/brcm63xx/patches-3.6/434-MIPS-BCM63XX-store-the-flash-type-in-global-variable.patch +++ /dev/null @@ -1,122 +0,0 @@ -From f888824d352df894ab721a5ca067b0313500efe7 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 3 May 2012 12:17:54 +0200 -Subject: [PATCH 38/59] MIPS: BCM63XX: store the flash type in global variable - ---- - arch/mips/bcm63xx/dev-flash.c | 36 +++++++++++++------ - .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 + - 2 files changed, 26 insertions(+), 12 deletions(-) - ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -25,6 +25,8 @@ - #include <bcm63xx_regs.h> - #include <bcm63xx_io.h> - -+int bcm63xx_attached_flash = -1; -+ - static struct mtd_partition mtd_partitions[] = { - { - .name = "cfe", -@@ -86,20 +88,23 @@ static int __init bcm63xx_detect_flash_t - bcm63xx_spi_flash_info[0].max_speed_hz = 16666667; - - if (val & STRAPBUS_6328_BOOT_SEL_SERIAL) -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; - else -- return BCM63XX_FLASH_TYPE_NAND; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND; -+ break; - case BCM6338_CPU_ID: - case BCM6345_CPU_ID: - case BCM6348_CPU_ID: - /* no way to auto detect so assume parallel */ -- return BCM63XX_FLASH_TYPE_PARALLEL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL; -+ break; - case BCM6358_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); - if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL) -- return BCM63XX_FLASH_TYPE_PARALLEL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL; - else -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; -+ break; - case BCM6362_CPU_ID: - val = bcm_misc_readl(MISC_STRAPBUS_6362_REG); - if (val & STRAPBUS_6362_HSSPI_CLK_FAST) -@@ -108,9 +113,10 @@ static int __init bcm63xx_detect_flash_t - bcm63xx_spi_flash_info[0].max_speed_hz = 20000000; - - if (val & STRAPBUS_6362_BOOT_SEL_SERIAL) -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; - else -- return BCM63XX_FLASH_TYPE_NAND; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND; -+ break; - case BCM6368_CPU_ID: - val = bcm_gpio_readl(GPIO_STRAPBUS_REG); - if (val & STRAPBUS_6368_SPI_CLK_FAST) -@@ -118,25 +124,32 @@ static int __init bcm63xx_detect_flash_t - - switch (val & STRAPBUS_6368_BOOT_SEL_MASK) { - case STRAPBUS_6368_BOOT_SEL_NAND: -- return BCM63XX_FLASH_TYPE_NAND; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND; -+ break; - case STRAPBUS_6368_BOOT_SEL_SERIAL: -- return BCM63XX_FLASH_TYPE_SERIAL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL; -+ break; - case STRAPBUS_6368_BOOT_SEL_PARALLEL: -- return BCM63XX_FLASH_TYPE_PARALLEL; -+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL; -+ break; -+ default: -+ return -EINVAL; - } - default: - return -EINVAL; - } -+ -+ return 0; - } - - int __init bcm63xx_flash_register(void) - { -- int flash_type; - u32 val; - -- flash_type = bcm63xx_detect_flash_type(); - -- switch (flash_type) { -+ bcm63xx_detect_flash_type(); -+ -+ switch (bcm63xx_attached_flash) { - case BCM63XX_FLASH_TYPE_PARALLEL: - /* read base address of boot chip select (0) */ - val = bcm_mpi_readl(MPI_CSBASE_REG(0)); -@@ -157,7 +170,7 @@ int __init bcm63xx_flash_register(void) - return -ENODEV; - default: - pr_err("flash detection failed for BCM%x: %d\n", -- bcm63xx_get_cpu_id(), flash_type); -+ bcm63xx_get_cpu_id(), bcm63xx_attached_flash); - return -ENODEV; - } - } ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -@@ -7,6 +7,8 @@ enum { - BCM63XX_FLASH_TYPE_NAND, - }; - -+extern int bcm63xx_attached_flash; -+ - int __init bcm63xx_flash_register(void); - - #endif /* __BCM63XX_FLASH_H */ diff --git a/target/linux/brcm63xx/patches-3.6/435-BCM63XX-add-a-fixup-for-ath9k-devices.patch b/target/linux/brcm63xx/patches-3.6/435-BCM63XX-add-a-fixup-for-ath9k-devices.patch deleted file mode 100644 index a3b30e4443..0000000000 --- a/target/linux/brcm63xx/patches-3.6/435-BCM63XX-add-a-fixup-for-ath9k-devices.patch +++ /dev/null @@ -1,227 +0,0 @@ -From fb6f6f58db9ae9cf27ab01f5f09cfbc5c078a7b8 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 3 May 2012 14:36:11 +0200 -Subject: [PATCH 66/80] BCM63XX: add a fixup for ath9k devices - ---- - arch/mips/bcm63xx/Makefile | 2 +- - arch/mips/bcm63xx/pci-ath9k-fixup.c | 190 ++++++++++++++++++++ - .../include/asm/mach-bcm63xx/pci_ath9k_fixup.h | 7 + - 3 files changed, 198 insertions(+), 1 deletion(-) - create mode 100644 arch/mips/bcm63xx/pci-ath9k-fixup.c - create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h - ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,7 +1,7 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o setup.o \ - timer.o dev-dsp.o dev-enet.o dev-flash.o dev-hsspi.o \ - dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-usb-ehci.o \ -- dev-usb-ohci.o dev-wdt.o -+ dev-usb-ohci.o dev-wdt.o pci-ath9k-fixup.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- /dev/null -+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c -@@ -0,0 +1,190 @@ -+/* -+ * Broadcom BCM63XX Ath9k EEPROM fixup helper. -+ * -+ * Copytight (C) 2012 Jonas Gorski <jonas.gorski@gmail.com> -+ * -+ * Based on -+ * -+ * Atheros AP94 reference board PCI initialization -+ * -+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org> -+ * -+ * This program is free software; you can redistribute it and/or modify it -+ * under the terms of the GNU General Public License version 2 as published -+ * by the Free Software Foundation. -+ */ -+ -+#include <linux/pci.h> -+#include <linux/delay.h> -+#include <linux/ath9k_platform.h> -+ -+#include <bcm63xx_cpu.h> -+#include <bcm63xx_io.h> -+#include <bcm63xx_nvram.h> -+#include <bcm63xx_dev_pci.h> -+#include <bcm63xx_dev_flash.h> -+#include <bcm63xx_dev_hsspi.h> -+#include <pci_ath9k_fixup.h> -+ -+struct ath9k_fixup { -+ unsigned slot; -+ u8 mac[ETH_ALEN]; -+ struct ath9k_platform_data pdata; -+}; -+ -+static int ath9k_num_fixups; -+static struct ath9k_fixup ath9k_fixups[2] = { -+ { -+ .slot = 255, -+ .pdata = { -+ .led_pin = -1, -+ }, -+ }, -+ { -+ .slot = 255, -+ .pdata = { -+ .led_pin = -1, -+ }, -+ }, -+}; -+ -+static u16 *bcm63xx_read_eeprom(u16 *eeprom, u32 offset) -+{ -+ u32 addr; -+ -+ if (BCMCPU_IS_6328()) { -+ addr = 0x18000000; -+ } else { -+ addr = bcm_mpi_readl(MPI_CSBASE_REG(0)); -+ addr &= MPI_CSBASE_BASE_MASK; -+ } -+ -+ switch (bcm63xx_attached_flash) { -+ case BCM63XX_FLASH_TYPE_PARALLEL: -+ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); -+ return eeprom; -+ case BCM63XX_FLASH_TYPE_SERIAL: -+ /* the first megabyte is memory mapped */ -+ if (offset < 0x100000) { -+ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); -+ return eeprom; -+ } -+ -+ if (BCMCPU_IS_6328()) { -+ /* we can change the memory mapped megabyte */ -+ bcm_hsspi_writel(offset & 0xf00000, 0x18); -+ memcpy(eeprom, (void *)KSEG1ADDR(addr + (offset & 0xfffff)), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); -+ bcm_hsspi_writel(0, 0x18); -+ return eeprom; -+ } -+ /* can't do anything here without talking to the SPI controller. */ -+ case BCM63XX_FLASH_TYPE_NAND: -+ default: -+ return NULL; -+ } -+} -+ -+static void ath9k_pci_fixup(struct pci_dev *dev) -+{ -+ void __iomem *mem; -+ struct ath9k_platform_data *pdata = NULL; -+ u16 *cal_data = NULL; -+ u16 cmd; -+ u32 bar0; -+ u32 val; -+ unsigned i; -+ -+ for (i = 0; i < ath9k_num_fixups; i++) { -+ if (ath9k_fixups[i].slot != PCI_SLOT(dev->devfn)) -+ continue; -+ -+ cal_data = ath9k_fixups[i].pdata.eeprom_data; -+ pdata = &ath9k_fixups[i].pdata; -+ break; -+ } -+ -+ if (cal_data == NULL) -+ return; -+ -+ if (*cal_data != 0xa55a) { -+ pr_err("pci %s: invalid calibration data\n", pci_name(dev)); -+ return; -+ } -+ -+ pr_info("pci %s: fixup device configuration\n", pci_name(dev)); -+ -+ switch (bcm63xx_get_cpu_id()) { -+ case BCM6328_CPU_ID: -+ val = BCM_PCIE_MEM_BASE_PA; -+ break; -+ case BCM6348_CPU_ID: -+ case BCM6358_CPU_ID: -+ case BCM6368_CPU_ID: -+ val = BCM_PCI_MEM_BASE_PA; -+ break; -+ default: -+ BUG(); -+ } -+ -+ mem = ioremap(val, 0x10000); -+ if (!mem) { -+ pr_err("pci %s: ioremap error\n", pci_name(dev)); -+ return; -+ } -+ -+ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0); -+ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0); -+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, val); -+ -+ pci_read_config_word(dev, PCI_COMMAND, &cmd); -+ cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; -+ pci_write_config_word(dev, PCI_COMMAND, cmd); -+ -+ /* set offset to first reg address */ -+ cal_data += 3; -+ while(*cal_data != 0xffff) { -+ u32 reg; -+ reg = *cal_data++; -+ val = *cal_data++; -+ val |= (*cal_data++) << 16; -+ -+ writel(val, mem + reg); -+ udelay(100); -+ } -+ -+ pci_read_config_dword(dev, PCI_VENDOR_ID, &val); -+ dev->vendor = val & 0xffff; -+ dev->device = (val >> 16) & 0xffff; -+ -+ pci_read_config_dword(dev, PCI_CLASS_REVISION, &val); -+ dev->revision = val & 0xff; -+ dev->class = val >> 8; /* upper 3 bytes */ -+ -+ pci_read_config_word(dev, PCI_COMMAND, &cmd); -+ cmd &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY); -+ pci_write_config_word(dev, PCI_COMMAND, cmd); -+ -+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, bar0); -+ -+ iounmap(mem); -+ -+ dev->dev.platform_data = pdata; -+} -+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); -+ -+void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset) -+{ -+ if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) -+ return; -+ -+ ath9k_fixups[ath9k_num_fixups].slot = slot; -+ -+ if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) -+ return; -+ -+ if (bcm63xx_nvram_get_mac_address(ath9k_fixups[ath9k_num_fixups].mac)) -+ return; -+ -+ ath9k_fixups[ath9k_num_fixups].pdata.macaddr = ath9k_fixups[ath9k_num_fixups].mac; -+ ath9k_num_fixups++; -+} ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -@@ -0,0 +1,7 @@ -+#ifndef _PCI_ATH9K_FIXUP -+#define _PCI_ATH9K_FIXUP -+ -+ -+void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init; -+ -+#endif /* _PCI_ATH9K_FIXUP */ diff --git a/target/linux/brcm63xx/patches-3.6/436-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch b/target/linux/brcm63xx/patches-3.6/436-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch deleted file mode 100644 index 3b34eec6ba..0000000000 --- a/target/linux/brcm63xx/patches-3.6/436-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch +++ /dev/null @@ -1,120 +0,0 @@ -Allow bcm63xxpart to receive a caldata offset if calibration data is -contained in flash. ---- - drivers/mtd/bcm63xxpart.c | 51 ++++++++++++++++++++++++++++++++++++--- - include/linux/mtd/partitions.h | 2 + - 2 files changed, 49 insertions(+), 4 deletions(-) - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -76,10 +76,12 @@ static int bcm63xx_parse_cfe_partitions( - struct mtd_partition *parts; - int ret; - size_t retlen; -- unsigned int rootfsaddr, kerneladdr, spareaddr; -+ unsigned int rootfsaddr, kerneladdr, spareaddr, nvramaddr; - unsigned int rootfslen, kernellen, sparelen, totallen; - unsigned int cfelen, nvramlen; - unsigned int cfe_erasesize; -+ unsigned int caldatalen1 = 0, caldataaddr1 = 0; -+ unsigned int caldatalen2 = 0, caldataaddr2 = 0; - int i; - u32 computed_crc; - bool rootfs_first = false; -@@ -93,6 +95,24 @@ static int bcm63xx_parse_cfe_partitions( - cfelen = cfe_erasesize; - nvramlen = bcm63xx_nvram_get_psi_size() * 1024; - nvramlen = roundup(nvramlen, cfe_erasesize); -+ nvramaddr = master->size - nvramlen; -+ -+ if (data) { -+ if (data->caldata[0]) { -+ caldatalen1 = cfe_erasesize; -+ caldataaddr1 = rounddown(data->caldata[0], -+ cfe_erasesize); -+ } -+ if (data->caldata[1]) { -+ caldatalen2 = cfe_erasesize; -+ caldataaddr2 = rounddown(data->caldata[1], -+ cfe_erasesize); -+ } -+ if (caldataaddr1 == caldataaddr2) { -+ caldataaddr2 = 0; -+ caldatalen2 = 0; -+ } -+ } - - /* Allocate memory for buffer */ - buf = vmalloc(sizeof(struct bcm_tag)); -@@ -144,7 +164,7 @@ static int bcm63xx_parse_cfe_partitions( - rootfsaddr = 0; - spareaddr = cfelen; - } -- sparelen = master->size - spareaddr - nvramlen; -+ sparelen = min_not_zero(nvramaddr, caldataaddr1) - spareaddr; - - /* Determine number of partitions */ - if (rootfslen > 0) -@@ -153,6 +173,12 @@ static int bcm63xx_parse_cfe_partitions( - if (kernellen > 0) - nrparts++; - -+ if (caldatalen1 > 0) -+ nrparts++; -+ -+ if (caldatalen2 > 0) -+ nrparts++; -+ - /* Ask kernel for more memory */ - parts = kzalloc(sizeof(*parts) * nrparts + 10 * nrparts, GFP_KERNEL); - if (!parts) { -@@ -190,15 +216,32 @@ static int bcm63xx_parse_cfe_partitions( - curpart++; - } - -+ if (caldatalen1 > 0) { -+ if (caldatalen2 > 0) -+ parts[curpart].name = "cal_data1"; -+ else -+ parts[curpart].name = "cal_data"; -+ parts[curpart].offset = caldataaddr1; -+ parts[curpart].size = caldatalen1; -+ curpart++; -+ } -+ -+ if (caldatalen2 > 0) { -+ parts[curpart].name = "cal_data2"; -+ parts[curpart].offset = caldataaddr2; -+ parts[curpart].size = caldatalen2; -+ curpart++; -+ } -+ - parts[curpart].name = "nvram"; -- parts[curpart].offset = master->size - nvramlen; -+ parts[curpart].offset = nvramaddr; - parts[curpart].size = nvramlen; - curpart++; - - /* Global partition "linux" to make easy firmware upgrade */ - parts[curpart].name = "linux"; - parts[curpart].offset = cfelen; -- parts[curpart].size = master->size - cfelen - nvramlen; -+ parts[curpart].size = min_not_zero(nvramaddr, caldataaddr1) - cfelen; - - for (i = 0; i < nrparts; i++) - pr_info("Partition %d is %s offset %llx and length %llx\n", i, ---- a/include/linux/mtd/partitions.h -+++ b/include/linux/mtd/partitions.h -@@ -58,10 +58,12 @@ struct device_node; - /** - * struct mtd_part_parser_data - used to pass data to MTD partition parsers. - * @origin: for RedBoot, start address of MTD device -+ * @caldata: for CFE, start address of wifi calibration data - * @of_node: for OF parsers, device node containing partitioning information - */ - struct mtd_part_parser_data { - unsigned long origin; -+ unsigned long caldata[2]; - struct device_node *of_node; - }; - diff --git a/target/linux/brcm63xx/patches-3.6/437-MIPS-BCM63XX-pass-caldata-info-to-flash.patch b/target/linux/brcm63xx/patches-3.6/437-MIPS-BCM63XX-pass-caldata-info-to-flash.patch deleted file mode 100644 index c8962746da..0000000000 --- a/target/linux/brcm63xx/patches-3.6/437-MIPS-BCM63XX-pass-caldata-info-to-flash.patch +++ /dev/null @@ -1,82 +0,0 @@ -From 977f8a30103b9c4992cab8f49357fe0d4274004f Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 3 May 2012 14:55:26 +0200 -Subject: [PATCH 69/80] MIPS: BCM63XX: pass caldata info to flash - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +- - arch/mips/bcm63xx/dev-flash.c | 9 ++++++++- - arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 4 +++- - 3 files changed, 12 insertions(+), 3 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -957,7 +957,7 @@ int __init board_register_devices(void) - if (board.num_spis) - spi_register_board_info(board.spis, board.num_spis); - -- bcm63xx_flash_register(); -+ bcm63xx_flash_register(board.has_caldata, board.caldata); - - /* count number of LEDs defined by this device */ - while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -35,12 +35,15 @@ static struct mtd_partition mtd_partitio - } - }; - -+static struct mtd_part_parser_data bcm63xx_parser_data; -+ - static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL }; - - static struct physmap_flash_data flash_data = { - .width = 2, - .parts = mtd_partitions, - .part_probe_types = bcm63xx_part_types, -+ .pp_data = &bcm63xx_parser_data, - }; - - static struct resource mtd_resources[] = { -@@ -62,6 +65,7 @@ static struct platform_device mtd_dev = - - static struct flash_platform_data bcm63xx_flash_data = { - .part_probe_types = bcm63xx_part_types, -+ .pp_data = &bcm63xx_parser_data, - }; - - static struct spi_board_info bcm63xx_spi_flash_info[] = { -@@ -142,10 +146,13 @@ static int __init bcm63xx_detect_flash_t - return 0; - } - --int __init bcm63xx_flash_register(void) -+int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata) - { - u32 val; -+ unsigned int i; - -+ for (i = 0; i < num_caldata; i++) -+ bcm63xx_parser_data.caldata[i] = caldata[i].caldata_offset; - - bcm63xx_detect_flash_type(); - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -@@ -1,6 +1,8 @@ - #ifndef __BCM63XX_FLASH_H - #define __BCM63XX_FLASH_H - -+#include <board_bcm963xx.h> -+ - enum { - BCM63XX_FLASH_TYPE_PARALLEL, - BCM63XX_FLASH_TYPE_SERIAL, -@@ -9,6 +11,6 @@ enum { - - extern int bcm63xx_attached_flash; - --int __init bcm63xx_flash_register(void); -+int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata); - - #endif /* __BCM63XX_FLASH_H */ diff --git a/target/linux/brcm63xx/patches-3.6/438-MIPS-BCM63XX-enable-USB-for-BCM6328.patch b/target/linux/brcm63xx/patches-3.6/438-MIPS-BCM63XX-enable-USB-for-BCM6328.patch deleted file mode 100644 index 1693548d41..0000000000 --- a/target/linux/brcm63xx/patches-3.6/438-MIPS-BCM63XX-enable-USB-for-BCM6328.patch +++ /dev/null @@ -1,60 +0,0 @@ -From 38c3f8d21da90f0833578a157e22ddabf4d576bd Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 12 Feb 2012 14:28:34 +0100 -Subject: [PATCH 48/84] MIPS: BCM63XX: enable USB for BCM6328 - -The USB controller is the same as the one on BCM6368. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/dev-usb-ehci.c | 2 +- - arch/mips/bcm63xx/dev-usb-ohci.c | 3 ++- - drivers/usb/host/ehci-bcm63xx.c | 2 +- - drivers/usb/host/ohci-bcm63xx.c | 2 +- - 4 files changed, 5 insertions(+), 4 deletions(-) - ---- a/arch/mips/bcm63xx/dev-usb-ehci.c -+++ b/arch/mips/bcm63xx/dev-usb-ehci.c -@@ -39,7 +39,7 @@ static struct platform_device bcm63xx_eh - - int __init bcm63xx_ehci_register(void) - { -- if (!BCMCPU_IS_6358() && !BCMCPU_IS_6368()) -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6368()) - return 0; - - ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); ---- a/arch/mips/bcm63xx/dev-usb-ohci.c -+++ b/arch/mips/bcm63xx/dev-usb-ohci.c -@@ -39,7 +39,8 @@ static struct platform_device bcm63xx_oh - - int __init bcm63xx_ohci_register(void) - { -- if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358() && !BCMCPU_IS_6368()) -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6348() && !BCMCPU_IS_6358() && -+ !BCMCPU_IS_6368()) - return 0; - - ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0); ---- a/drivers/usb/host/ehci-bcm63xx.c -+++ b/drivers/usb/host/ehci-bcm63xx.c -@@ -99,7 +99,7 @@ static int __devinit ehci_hcd_bcm63xx_dr - bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, - USBH_PRIV_TEST_6358_REG); - -- } else if (BCMCPU_IS_6368()) { -+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) { - - reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); - reg &= ~USBH_PRIV_SWAP_EHCI_DATA_MASK; ---- a/drivers/usb/host/ohci-bcm63xx.c -+++ b/drivers/usb/host/ohci-bcm63xx.c -@@ -95,7 +95,7 @@ static int __devinit ohci_hcd_bcm63xx_dr - bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, - USBH_PRIV_TEST_6358_REG); - -- } else if (BCMCPU_IS_6368()) { -+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) { - reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); - reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; - reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; diff --git a/target/linux/brcm63xx/patches-3.6/439-MIPS-BCM63XX-wire-up-the-HS-SPI-controller-for-BCM63.patch b/target/linux/brcm63xx/patches-3.6/439-MIPS-BCM63XX-wire-up-the-HS-SPI-controller-for-BCM63.patch deleted file mode 100644 index 7561569188..0000000000 --- a/target/linux/brcm63xx/patches-3.6/439-MIPS-BCM63XX-wire-up-the-HS-SPI-controller-for-BCM63.patch +++ /dev/null @@ -1,56 +0,0 @@ -From ed225910f0e062d9c28d5cf216f97b3cf457a8c5 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Mon, 21 Nov 2011 00:55:49 +0100 -Subject: [PATCH 58/81] MIPS: BCM63XX: wire up the HS SPI controller for BCM6362 - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/clk.c | 2 ++ - arch/mips/bcm63xx/dev-hsspi.c | 7 +++++-- - .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h | 1 + - 3 files changed, 8 insertions(+), 2 deletions(-) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -218,6 +218,8 @@ static void hsspi_set(struct clk *clk, i - - if (BCMCPU_IS_6328()) - mask = CKCTL_6328_HSSPI_EN; -+ else if (BCMCPU_IS_6362()) -+ mask = CKCTL_6362_HSSPI_EN; - else - return; - ---- a/arch/mips/bcm63xx/dev-hsspi.c -+++ b/arch/mips/bcm63xx/dev-hsspi.c -@@ -43,7 +43,7 @@ static struct platform_device bcm63xx_hs - int __init bcm63xx_hsspi_register(void) - { - -- if (!BCMCPU_IS_6328()) -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362()) - return -ENODEV; - - spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI); -@@ -51,7 +51,10 @@ int __init bcm63xx_hsspi_register(void) - spi_resources[0].end += RSET_HSSPI_SIZE - 1; - spi_resources[1].start = bcm63xx_get_irq_number(IRQ_HSSPI); - -- spi_pdata.speed_hz = HSSPI_PLL_HZ_6328; -+ if (BCMCPU_IS_6328()) -+ spi_pdata.speed_hz = HSSPI_PLL_HZ_6328; -+ else -+ spi_pdata.speed_hz = HSSPI_PLL_HZ; - - return platform_device_register(&bcm63xx_hsspi_device); - } ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h -@@ -16,6 +16,7 @@ struct bcm63xx_hsspi_pdata { - #define bcm_hsspi_writel(v, o) bcm_rset_writel(RSET_HSSPI, (v), (o)) - - #define HSSPI_PLL_HZ_6328 133333333 -+#define HSSPI_PLL_HZ 400000000 - - #define HSSPI_BUFFER_LEN 512 - diff --git a/target/linux/brcm63xx/patches-3.6/440-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.6/440-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch deleted file mode 100644 index f1f1342864..0000000000 --- a/target/linux/brcm63xx/patches-3.6/440-MIPS-BCM63XX-enable-SPI-controller-for-BCM6362.patch +++ /dev/null @@ -1,101 +0,0 @@ -From eef84812bc7ffd590da6ad6b83bfeebaa43a7055 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Thu, 5 Jul 2012 21:19:20 +0200 -Subject: [PATCH 58/84] MIPS: BCM63XX: enable SPI controller for BCM6362 - ---- - arch/mips/bcm63xx/clk.c | 2 ++ - arch/mips/bcm63xx/dev-spi.c | 11 ++++++++++- - .../include/asm/mach-bcm63xx/bcm63xx_dev_spi.h | 3 +++ - arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 16 ++++++++++++++++ - 4 files changed, 31 insertions(+), 1 deletions(-) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -199,6 +199,8 @@ static void spi_set(struct clk *clk, int - mask = CKCTL_6348_SPI_EN; - else if (BCMCPU_IS_6358()) - mask = CKCTL_6358_SPI_EN; -+ else if (BCMCPU_IS_6362()) -+ mask = CKCTL_6362_SPI_EN; - else - /* BCMCPU_IS_6368 */ - mask = CKCTL_6368_SPI_EN; ---- a/arch/mips/bcm63xx/dev-spi.c -+++ b/arch/mips/bcm63xx/dev-spi.c -@@ -34,6 +34,10 @@ static const unsigned long bcm6358_regs_ - __GEN_SPI_REGS_TABLE(6358) - }; - -+static const unsigned long bcm6362_regs_spi[] = { -+ __GEN_SPI_REGS_TABLE(6362) -+}; -+ - static const unsigned long bcm6368_regs_spi[] = { - __GEN_SPI_REGS_TABLE(6368) - }; -@@ -49,6 +53,8 @@ static __init void bcm63xx_spi_regs_init - bcm63xx_regs_spi = bcm6348_regs_spi; - if (BCMCPU_IS_6358()) - bcm63xx_regs_spi = bcm6358_regs_spi; -+ if (BCMCPU_IS_6362()) -+ bcm63xx_regs_spi = bcm6362_regs_spi; - if (BCMCPU_IS_6368()) - bcm63xx_regs_spi = bcm6368_regs_spi; - } -@@ -99,6 +105,9 @@ int __init bcm63xx_spi_register(void) - /* Set bus frequency */ - spi_pdata.speed_hz = clk_get_rate(periph_clk); - -+ if (BCMCPU_IS_6362()) -+ spi_pdata.bus_num = 1; -+ - spi_resources[0].start = bcm63xx_regset_address(RSET_SPI); - spi_resources[0].end = spi_resources[0].start; - spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI); -@@ -110,7 +119,7 @@ int __init bcm63xx_spi_register(void) - spi_pdata.msg_ctl_width = SPI_6338_MSG_CTL_WIDTH; - } - -- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) { -+ if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { - spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1; - spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE; - spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h -@@ -81,6 +81,9 @@ static inline unsigned long bcm63xx_spir - #ifdef CONFIG_BCM63XX_CPU_6358 - __GEN_SPI_RSET(6358) - #endif -+#ifdef CONFIG_BCM63XX_CPU_6362 -+ __GEN_SPI_RSET(6362) -+#endif - #ifdef CONFIG_BCM63XX_CPU_6368 - __GEN_SPI_RSET(6368) - #endif ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -1223,6 +1223,22 @@ - #define SPI_6358_MSG_TAIL 0x709 - #define SPI_6358_RX_TAIL 0x70B - -+/* BCM 6362 SPI core */ -+#define SPI_6362_MSG_CTL 0x00 /* 16-bits register */ -+#define SPI_6362_MSG_DATA 0x02 -+#define SPI_6362_MSG_DATA_SIZE 0x21e -+#define SPI_6362_RX_DATA 0x400 -+#define SPI_6362_RX_DATA_SIZE 0x220 -+#define SPI_6362_CMD 0x700 /* 16-bits register */ -+#define SPI_6362_INT_STATUS 0x702 -+#define SPI_6362_INT_MASK_ST 0x703 -+#define SPI_6362_INT_MASK 0x704 -+#define SPI_6362_ST 0x705 -+#define SPI_6362_CLK_CFG 0x706 -+#define SPI_6362_FILL_BYTE 0x707 -+#define SPI_6362_MSG_TAIL 0x709 -+#define SPI_6362_RX_TAIL 0x70B -+ - /* BCM 6358 SPI core */ - #define SPI_6368_MSG_CTL 0x00 /* 16-bits register */ - #define SPI_6368_MSG_CTL_WIDTH 16 diff --git a/target/linux/brcm63xx/patches-3.6/441-MIPS-BCM63XX-enable-USB-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.6/441-MIPS-BCM63XX-enable-USB-for-BCM6362.patch deleted file mode 100644 index bf1ca1c082..0000000000 --- a/target/linux/brcm63xx/patches-3.6/441-MIPS-BCM63XX-enable-USB-for-BCM6362.patch +++ /dev/null @@ -1,84 +0,0 @@ -From fb9e98936590637c26b66d60137a7b44b329a254 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 12 Feb 2012 14:40:56 +0100 -Subject: [PATCH 59/84] MIPS: BCM63XX: enable USB for BCM6362 - -BCM6362 has the same USB controller as BCM6368. - -Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> ---- - arch/mips/bcm63xx/Kconfig | 2 ++ - arch/mips/bcm63xx/clk.c | 4 ++++ - arch/mips/bcm63xx/dev-usb-ehci.c | 3 ++- - arch/mips/bcm63xx/dev-usb-ohci.c | 2 +- - drivers/usb/host/ehci-bcm63xx.c | 2 +- - drivers/usb/host/ohci-bcm63xx.c | 2 +- - 6 files changed, 11 insertions(+), 4 deletions(-) - ---- a/arch/mips/bcm63xx/Kconfig -+++ b/arch/mips/bcm63xx/Kconfig -@@ -27,6 +27,8 @@ config BCM63XX_CPU_6358 - config BCM63XX_CPU_6362 - bool "support 6362 CPU" - select HW_HAS_PCI -+ select USB_ARCH_HAS_OHCI if USB_SUPPORT -+ select USB_ARCH_HAS_EHCI if USB_SUPPORT - - config BCM63XX_CPU_6368 - bool "support 6368 CPU" ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -178,6 +178,8 @@ static void usbh_set(struct clk *clk, in - { - if (BCMCPU_IS_6348()) - bcm_hwclock_set(CKCTL_6348_USBH_EN, enable); -+ else if (BCMCPU_IS_6362()) -+ bcm_hwclock_set(CKCTL_6362_USBH_EN, enable); - else if (BCMCPU_IS_6368()) - bcm_hwclock_set(CKCTL_6368_USBH_EN, enable); - } ---- a/arch/mips/bcm63xx/dev-usb-ehci.c -+++ b/arch/mips/bcm63xx/dev-usb-ehci.c -@@ -39,7 +39,8 @@ static struct platform_device bcm63xx_eh - - int __init bcm63xx_ehci_register(void) - { -- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6368()) -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6362() && -+ !BCMCPU_IS_6368()) - return 0; - - ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); ---- a/arch/mips/bcm63xx/dev-usb-ohci.c -+++ b/arch/mips/bcm63xx/dev-usb-ohci.c -@@ -40,7 +40,7 @@ static struct platform_device bcm63xx_oh - int __init bcm63xx_ohci_register(void) - { - if (!BCMCPU_IS_6328() && !BCMCPU_IS_6348() && !BCMCPU_IS_6358() && -- !BCMCPU_IS_6368()) -+ !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) - return 0; - - ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0); ---- a/drivers/usb/host/ehci-bcm63xx.c -+++ b/drivers/usb/host/ehci-bcm63xx.c -@@ -99,7 +99,7 @@ static int __devinit ehci_hcd_bcm63xx_dr - bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, - USBH_PRIV_TEST_6358_REG); - -- } else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) { -+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { - - reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); - reg &= ~USBH_PRIV_SWAP_EHCI_DATA_MASK; ---- a/drivers/usb/host/ohci-bcm63xx.c -+++ b/drivers/usb/host/ohci-bcm63xx.c -@@ -95,7 +95,7 @@ static int __devinit ohci_hcd_bcm63xx_dr - bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, - USBH_PRIV_TEST_6358_REG); - -- } else if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) { -+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { - reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); - reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; - reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; diff --git a/target/linux/brcm63xx/patches-3.6/442-MIPS-BCM63XX-enable-enetsw-for-BCM6362.patch b/target/linux/brcm63xx/patches-3.6/442-MIPS-BCM63XX-enable-enetsw-for-BCM6362.patch deleted file mode 100644 index ae46ec4061..0000000000 --- a/target/linux/brcm63xx/patches-3.6/442-MIPS-BCM63XX-enable-enetsw-for-BCM6362.patch +++ /dev/null @@ -1,77 +0,0 @@ -From bf9d506bd144b95f8bb4127350ab2db5fba9c12e Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Sun, 8 Jul 2012 21:07:12 +0200 -Subject: [PATCH 60/84] MIPS: BCM63XX: enable enetsw for BCM6362 - ---- - arch/mips/bcm63xx/clk.c | 7 ++++++- - arch/mips/bcm63xx/dev-enet.c | 6 ++++-- - .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 1 + - 3 files changed, 11 insertions(+), 3 deletions(-) - ---- a/arch/mips/bcm63xx/clk.c -+++ b/arch/mips/bcm63xx/clk.c -@@ -120,11 +120,13 @@ static void enetsw_set(struct clk *clk, - { - u32 mask; - -- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368()) -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) - return; - - if (BCMCPU_IS_6328()) - mask = CKCTL_6328_ROBOSW_EN; -+ else if (BCMCPU_IS_6362()) -+ mask = CKCTL_6362_ROBOSW_EN; - else - mask = CKCTL_6368_ROBOSW_EN | CKCTL_6368_SWPKT_USB_EN | - CKCTL_6368_SWPKT_SAR_EN; -@@ -137,6 +139,9 @@ static void enetsw_set(struct clk *clk, - if (BCMCPU_IS_6328()) { - reg = PERF_SOFTRESET_6328_REG; - mask = SOFTRESET_6328_ENETSW_MASK; -+ } else if (BCMCPU_IS_6362()) { -+ reg = PERF_SOFTRESET_6362_REG; -+ mask = SOFTRESET_6362_ENETSW_MASK; - } else { - reg = PERF_SOFTRESET_6368_REG; - mask = SOFTRESET_6368_ENETSW_MASK; ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -141,7 +141,7 @@ static int __init register_shared(void) - shared_res[0].end = shared_res[0].start; - shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; - -- if (BCMCPU_IS_6328() || BCMCPU_IS_6368()) -+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) - chan_count = 32; - else - chan_count = 16; -@@ -224,7 +224,7 @@ bcm63xx_enetsw_register(const struct bcm - { - int ret; - -- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368()) -+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) - return -ENODEV; - - ret = register_shared(); -@@ -243,6 +243,8 @@ bcm63xx_enetsw_register(const struct bcm - - if (BCMCPU_IS_6328()) - enetsw_pd.num_ports = ENETSW_PORTS_6328; -+ else if (BCMCPU_IS_6362()) -+ enetsw_pd.num_ports = ENETSW_PORTS_6362; - else if (BCMCPU_IS_6368()) - enetsw_pd.num_ports = ENETSW_PORTS_6368; - ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -44,6 +44,7 @@ struct bcm63xx_enet_platform_data { - */ - #define ENETSW_MAX_PORT 6 - #define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */ -+#define ENETSW_PORTS_6362 6 /* 4 FE PHY + 2 RGMII */ - #define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */ - - #define ENETSW_RGMII_PORT0 4 diff --git a/target/linux/brcm63xx/patches-3.6/443-MIPS-BCM63XX-enable-enet-for-BCM6345.patch b/target/linux/brcm63xx/patches-3.6/443-MIPS-BCM63XX-enable-enet-for-BCM6345.patch deleted file mode 100644 index 5ffbe7389d..0000000000 --- a/target/linux/brcm63xx/patches-3.6/443-MIPS-BCM63XX-enable-enet-for-BCM6345.patch +++ /dev/null @@ -1,795 +0,0 @@ -[PATCH] MIPS: BCM63XX: enable ethernet for BCM6345 - -BCM6345 has a slightly older DMA engine which is not supported by default by -the bcm63xx_enet driver. This patch adds the missing Ethernet DMA definitions -as well as patches all the places in the ethernet driver were the DMA -reading/writing is different. - -Signed-off-by: Florian Fainelli <florian@openwrt.org> ---- ---- a/arch/mips/bcm63xx/dev-enet.c -+++ b/arch/mips/bcm63xx/dev-enet.c -@@ -9,10 +9,44 @@ - #include <linux/init.h> - #include <linux/kernel.h> - #include <linux/platform_device.h> -+#include <linux/export.h> - #include <bcm63xx_dev_enet.h> - #include <bcm63xx_io.h> - #include <bcm63xx_regs.h> - -+#ifdef BCMCPU_RUNTIME_DETECT -+static const unsigned long bcm6xxx_regs_enetdmac[] = { -+ [ENETDMAC_CHANCFG] = ENETDMAC_CHANCFG_REG, -+ [ENETDMAC_IR] = ENETDMAC_IR_REG, -+ [ENETDMAC_IRMASK] = ENETDMAC_IRMASK_REG, -+ [ENETDMAC_MAXBURST] = ENETDMAC_MAXBURST_REG, -+}; -+ -+static const unsigned long bcm6345_regs_enetdmac[] = { -+ [ENETDMAC_CHANCFG] = ENETDMA_6345_CHANCFG_REG, -+ [ENETDMAC_IR] = ENETDMA_6345_IR_REG, -+ [ENETDMAC_IRMASK] = ENETDMA_6345_IRMASK_REG, -+ [ENETDMAC_MAXBURST] = ENETDMA_6345_MAXBURST_REG, -+ [ENETDMAC_BUFALLOC] = ENETDMA_6345_BUFALLOC_REG, -+ [ENETDMAC_RSTART] = ENETDMA_6345_RSTART_REG, -+ [ENETDMAC_FC] = ENETDMA_6345_FC_REG, -+ [ENETDMAC_LEN] = ENETDMA_6345_LEN_REG, -+}; -+ -+const unsigned long *bcm63xx_regs_enetdmac; -+EXPORT_SYMBOL(bcm63xx_regs_enetdmac); -+ -+static __init void bcm63xx_enetdmac_regs_init(void) -+{ -+ if (BCMCPU_IS_6345()) -+ bcm63xx_regs_enetdmac = bcm6345_regs_enetdmac; -+ else -+ bcm63xx_regs_enetdmac = bcm6xxx_regs_enetdmac; -+} -+#else -+static __init void bcm63xx_enetdmac_regs_init(void) { } -+#endif -+ - static struct resource shared_res[] = { - { - .start = -1, /* filled at runtime */ -@@ -137,12 +171,19 @@ static int __init register_shared(void) - if (shared_device_registered) - return 0; - -+ bcm63xx_enetdmac_regs_init(); -+ - shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA); - shared_res[0].end = shared_res[0].start; -- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; -+ if (BCMCPU_IS_6345()) -+ shared_res[0].end += (RSET_6345_ENETDMA_SIZE) - 1; -+ else -+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; - - if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) - chan_count = 32; -+ else if (BCMCPU_IS_6345()) -+ chan_count = 8; - else - chan_count = 16; - -@@ -172,7 +213,7 @@ int __init bcm63xx_enet_register(int uni - if (unit > 1) - return -ENODEV; - -- if (unit == 1 && BCMCPU_IS_6338()) -+ if (unit == 1 && (BCMCPU_IS_6338() || BCMCPU_IS_6345())) - return -ENODEV; - - ret = register_shared(); -@@ -213,6 +254,20 @@ int __init bcm63xx_enet_register(int uni - dpd->phy_interrupt = bcm63xx_get_irq_number(IRQ_ENET_PHY); - } - -+ dpd->dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK; -+ dpd->dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK; -+ if (BCMCPU_IS_6345()) { -+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_CHAINING_MASK; -+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_WRAP_EN_MASK; -+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_FLOWC_EN_MASK; -+ dpd->dma_chan_int_mask |= ENETDMA_IR_BUFDONE_MASK; -+ dpd->dma_chan_int_mask |= ENETDMA_IR_NOTOWNER_MASK; -+ dpd->dma_chan_width = ENETDMA_6345_CHAN_WIDTH; -+ dpd->dma_no_sram = 1; -+ dpd->dma_desc_shift = ENETDMA_6345_DESC_SHIFT; -+ } else -+ dpd->dma_chan_width = ENETDMA_CHAN_WIDTH; -+ - ret = platform_device_register(pdev); - if (ret) - return ret; -@@ -248,6 +303,10 @@ bcm63xx_enetsw_register(const struct bcm - else if (BCMCPU_IS_6368()) - enetsw_pd.num_ports = ENETSW_PORTS_6368; - -+ enetsw_pd.dma_chan_width = ENETDMA_CHAN_WIDTH; -+ enetsw_pd.dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK; -+ enetsw_pd.dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK; -+ - ret = platform_device_register(&bcm63xx_enetsw_device); - if (ret) - return ret; ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h -@@ -715,6 +715,8 @@ - /************************************************************************* - * _REG relative to RSET_ENETDMA - *************************************************************************/ -+#define ENETDMA_CHAN_WIDTH 0x10 -+#define ENETDMA_6345_CHAN_WIDTH 0x40 - - /* Controller Configuration Register */ - #define ENETDMA_CFG_REG (0x0) -@@ -764,29 +766,54 @@ - /* State Ram Word 4 */ - #define ENETDMA_SRAM4_REG(x) (0x20c + (x) * 0x10) - -+/* Broadcom 6345 ENET DMA definitions */ -+#define ENETDMA_6345_CHANCFG_REG (0x00) -+ -+#define ENETDMA_6345_MAXBURST_REG (0x04) -+ -+#define ENETDMA_6345_RSTART_REG (0x08) -+ -+#define ENETDMA_6345_LEN_REG (0x0C) -+ -+#define ENETDMA_6345_IR_REG (0x14) -+ -+#define ENETDMA_6345_IRMASK_REG (0x18) -+ -+#define ENETDMA_6345_FC_REG (0x1C) -+ -+#define ENETDMA_6345_BUFALLOC_REG (0x20) -+ -+/* Shift down for EOP, SOP and WRAP bits */ -+#define ENETDMA_6345_DESC_SHIFT (3) - - /************************************************************************* - * _REG relative to RSET_ENETDMAC - *************************************************************************/ - - /* Channel Configuration register */ --#define ENETDMAC_CHANCFG_REG(x) ((x) * 0x10) -+#define ENETDMAC_CHANCFG_REG (0x0) - #define ENETDMAC_CHANCFG_EN_SHIFT 0 - #define ENETDMAC_CHANCFG_EN_MASK (1 << ENETDMA_CHANCFG_EN_SHIFT) - #define ENETDMAC_CHANCFG_PKTHALT_SHIFT 1 - #define ENETDMAC_CHANCFG_PKTHALT_MASK (1 << ENETDMA_CHANCFG_PKTHALT_SHIFT) -+#define ENETDMAC_CHANCFG_CHAINING_SHIFT 2 -+#define ENETDMAC_CHANCFG_CHAINING_MASK (1 << ENETDMAC_CHANCFG_CHAINING_SHIFT) -+#define ENETDMAC_CHANCFG_WRAP_EN_SHIFT 3 -+#define ENETDMAC_CHANCFG_WRAP_EN_MASK (1 << ENETDMAC_CHANCFG_WRAP_EN_SHIFT) -+#define ENETDMAC_CHANCFG_FLOWC_EN_SHIFT 4 -+#define ENETDMAC_CHANCFG_FLOWC_EN_MASK (1 << ENETDMAC_CHANCFG_FLOWC_EN_SHIFT) - - /* Interrupt Control/Status register */ --#define ENETDMAC_IR_REG(x) (0x4 + (x) * 0x10) -+#define ENETDMAC_IR_REG (0x4) - #define ENETDMAC_IR_BUFDONE_MASK (1 << 0) - #define ENETDMAC_IR_PKTDONE_MASK (1 << 1) - #define ENETDMAC_IR_NOTOWNER_MASK (1 << 2) - - /* Interrupt Mask register */ --#define ENETDMAC_IRMASK_REG(x) (0x8 + (x) * 0x10) -+#define ENETDMAC_IRMASK_REG (0x8) - - /* Maximum Burst Length */ --#define ENETDMAC_MAXBURST_REG(x) (0xc + (x) * 0x10) -+#define ENETDMAC_MAXBURST_REG (0xc) - - - /************************************************************************* -@@ -794,16 +821,16 @@ - *************************************************************************/ - - /* Ring Start Address register */ --#define ENETDMAS_RSTART_REG(x) ((x) * 0x10) -+#define ENETDMAS_RSTART_REG (0x0) - - /* State Ram Word 2 */ --#define ENETDMAS_SRAM2_REG(x) (0x4 + (x) * 0x10) -+#define ENETDMAS_SRAM2_REG (0x4) - - /* State Ram Word 3 */ --#define ENETDMAS_SRAM3_REG(x) (0x8 + (x) * 0x10) -+#define ENETDMAS_SRAM3_REG (0x8) - - /* State Ram Word 4 */ --#define ENETDMAS_SRAM4_REG(x) (0xc + (x) * 0x10) -+#define ENETDMAS_SRAM4_REG (0xc) - - - /************************************************************************* ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -115,26 +115,28 @@ static inline void enet_dma_writel(struc - bcm_writel(val, bcm_enet_shared_base[0] + off); - } - --static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off) -+static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off, int chan) - { -- return bcm_readl(bcm_enet_shared_base[1] + off); -+ return bcm_readl(bcm_enet_shared_base[1] + -+ (bcm63xx_enetdmacreg(off) + (chan * priv->dma_chan_width))); - } - - static inline void enet_dmac_writel(struct bcm_enet_priv *priv, -- u32 val, u32 off) -+ u32 val, u32 off, int chan) - { -- bcm_writel(val, bcm_enet_shared_base[1] + off); -+ bcm_writel(val, bcm_enet_shared_base[1] + -+ (bcm63xx_enetdmacreg(off) + (chan * priv->dma_chan_width))); - } - --static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off) -+static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off, int chan) - { -- return bcm_readl(bcm_enet_shared_base[2] + off); -+ return bcm_readl(bcm_enet_shared_base[2] + (off + (chan * priv->dma_chan_width))); - } - - static inline void enet_dmas_writel(struct bcm_enet_priv *priv, -- u32 val, u32 off) -+ u32 val, u32 off, int chan) - { -- bcm_writel(val, bcm_enet_shared_base[2] + off); -+ bcm_writel(val, bcm_enet_shared_base[2] + (off + (chan * priv->dma_chan_width))); - } - - /* -@@ -270,7 +272,7 @@ static int bcm_enet_refill_rx(struct net - len_stat = priv->rx_skb_size << DMADESC_LENGTH_SHIFT; - len_stat |= DMADESC_OWNER_MASK; - if (priv->rx_dirty_desc == priv->rx_ring_size - 1) { -- len_stat |= DMADESC_WRAP_MASK; -+ len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift); - priv->rx_dirty_desc = 0; - } else { - priv->rx_dirty_desc++; -@@ -281,7 +283,10 @@ static int bcm_enet_refill_rx(struct net - priv->rx_desc_count++; - - /* tell dma engine we allocated one buffer */ -- enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ if (!priv->dma_no_sram) -+ enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ else -+ enet_dmac_writel(priv, 1, ENETDMAC_BUFALLOC, priv->rx_chan); - } - - /* If rx ring is still empty, set a timer to try allocating -@@ -357,7 +362,8 @@ static int bcm_enet_receive_queue(struct - - /* if the packet does not have start of packet _and_ - * end of packet flag set, then just recycle it */ -- if ((len_stat & DMADESC_ESOP_MASK) != DMADESC_ESOP_MASK) { -+ if ((len_stat & (DMADESC_ESOP_MASK >> priv->dma_desc_shift)) != -+ (DMADESC_ESOP_MASK >> priv->dma_desc_shift)) { - dev->stats.rx_dropped++; - continue; - } -@@ -418,8 +424,8 @@ static int bcm_enet_receive_queue(struct - bcm_enet_refill_rx(dev); - - /* kick rx dma */ -- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_en_mask, -+ ENETDMAC_CHANCFG, priv->rx_chan); - } - - return processed; -@@ -494,10 +500,10 @@ static int bcm_enet_poll(struct napi_str - dev = priv->net_dev; - - /* ack interrupts */ -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->tx_chan); - - /* reclaim sent skb */ - tx_work_done = bcm_enet_tx_reclaim(dev, 0); -@@ -516,10 +522,10 @@ static int bcm_enet_poll(struct napi_str - napi_complete(napi); - - /* restore rx/tx interrupt */ -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->tx_chan); - - return rx_work_done; - } -@@ -562,8 +568,8 @@ static irqreturn_t bcm_enet_isr_dma(int - priv = netdev_priv(dev); - - /* mask rx/tx interrupts */ -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - napi_schedule(&priv->napi); - -@@ -624,14 +630,14 @@ static int bcm_enet_start_xmit(struct sk - DMA_TO_DEVICE); - - len_stat = (skb->len << DMADESC_LENGTH_SHIFT) & DMADESC_LENGTH_MASK; -- len_stat |= DMADESC_ESOP_MASK | -+ len_stat |= (DMADESC_ESOP_MASK >> priv->dma_desc_shift) | - DMADESC_APPEND_CRC | - DMADESC_OWNER_MASK; - - priv->tx_curr_desc++; - if (priv->tx_curr_desc == priv->tx_ring_size) { - priv->tx_curr_desc = 0; -- len_stat |= DMADESC_WRAP_MASK; -+ len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift); - } - priv->tx_desc_count--; - -@@ -642,8 +648,8 @@ static int bcm_enet_start_xmit(struct sk - wmb(); - - /* kick tx dma */ -- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_en_mask, -+ ENETDMAC_CHANCFG, priv->tx_chan); - - /* stop queue if no more desc available */ - if (!priv->tx_desc_count) -@@ -771,6 +777,9 @@ static void bcm_enet_set_flow(struct bcm - val &= ~ENET_RXCFG_ENFLOW_MASK; - enet_writel(priv, val, ENET_RXCFG_REG); - -+ if (priv->dma_no_sram) -+ return; -+ - /* tx flow control (pause frame generation) */ - val = enet_dma_readl(priv, ENETDMA_CFG_REG); - if (tx_en) -@@ -886,8 +895,8 @@ static int bcm_enet_open(struct net_devi - - /* mask all interrupts and request them */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); - if (ret) -@@ -966,8 +975,12 @@ static int bcm_enet_open(struct net_devi - priv->rx_curr_desc = 0; - - /* initialize flow control buffer allocation */ -- enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -- ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ if (!priv->dma_no_sram) -+ enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -+ ENETDMA_BUFALLOC_REG(priv->rx_chan)); -+ else -+ enet_dmac_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, -+ ENETDMAC_BUFALLOC, priv->rx_chan); - - if (bcm_enet_refill_rx(dev)) { - dev_err(kdev, "cannot allocate rx skb queue\n"); -@@ -976,18 +989,30 @@ static int bcm_enet_open(struct net_devi - } - - /* write rx & tx ring addresses */ -- enet_dmas_writel(priv, priv->rx_desc_dma, -- ENETDMAS_RSTART_REG(priv->rx_chan)); -- enet_dmas_writel(priv, priv->tx_desc_dma, -- ENETDMAS_RSTART_REG(priv->tx_chan)); -+ if (!priv->dma_no_sram) { -+ enet_dmas_writel(priv, priv->rx_desc_dma, -+ ENETDMAS_RSTART_REG, priv->rx_chan); -+ enet_dmas_writel(priv, priv->tx_desc_dma, -+ ENETDMAS_RSTART_REG, priv->tx_chan); -+ } else { -+ enet_dmac_writel(priv, priv->rx_desc_dma, -+ ENETDMAC_RSTART, priv->rx_chan); -+ enet_dmac_writel(priv, priv->tx_desc_dma, -+ ENETDMAC_RSTART, priv->tx_chan); -+ } - - /* clear remaining state ram for rx & tx channel */ -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); -+ if (!priv->dma_no_sram) { -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan); -+ } else { -+ enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->tx_chan); -+ } - - /* set max rx/tx length */ - enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG); -@@ -995,18 +1020,24 @@ static int bcm_enet_open(struct net_devi - - /* set dma maximum burst len */ - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ ENETDMAC_MAXBURST, priv->rx_chan); - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->tx_chan)); -+ ENETDMAC_MAXBURST, priv->tx_chan); - - /* set correct transmit fifo watermark */ - enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG); - - /* set flow control low/high threshold to 1/3 / 2/3 */ -- val = priv->rx_ring_size / 3; -- enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan)); -- val = (priv->rx_ring_size * 2) / 3; -- enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan)); -+ if (!priv->dma_no_sram) { -+ val = priv->rx_ring_size / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan)); -+ val = (priv->rx_ring_size * 2) / 3; -+ enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan)); -+ } else { -+ enet_dmac_writel(priv, 5, ENETDMAC_FC, priv->rx_chan); -+ enet_dmac_writel(priv, priv->rx_ring_size, ENETDMAC_LEN, priv->rx_chan); -+ enet_dmac_writel(priv, priv->tx_ring_size, ENETDMAC_LEN, priv->tx_chan); -+ } - - /* all set, enable mac and interrupts, start dma engine and - * kick rx dma channel */ -@@ -1015,26 +1046,26 @@ static int bcm_enet_open(struct net_devi - val |= ENET_CTL_ENABLE_MASK; - enet_writel(priv, val, ENET_CTL_REG); - enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); -- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_en_mask, -+ ENETDMAC_CHANCFG, priv->rx_chan); - - /* watch "mib counters about to overflow" interrupt */ - enet_writel(priv, ENET_IR_MIB, ENET_IR_REG); - enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG); - - /* watch "packet transferred" interrupt in rx and tx */ -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IR, priv->tx_chan); - - /* make sure we enable napi before rx interrupt */ - napi_enable(&priv->napi); - -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, priv->dma_chan_int_mask, -+ ENETDMAC_IRMASK, priv->tx_chan); - - if (priv->has_phy) - phy_start(priv->phydev); -@@ -1111,13 +1142,13 @@ static void bcm_enet_disable_dma(struct - { - int limit; - -- enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG, chan); - - limit = 1000; - do { - u32 val; - -- val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan)); -+ val = enet_dmac_readl(priv, ENETDMAC_CHANCFG, chan); - if (!(val & ENETDMAC_CHANCFG_EN_MASK)) - break; - udelay(1); -@@ -1144,8 +1175,8 @@ static int bcm_enet_stop(struct net_devi - - /* mask all interrupts */ - enet_writel(priv, 0, ENET_IRMASK_REG); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - /* make sure no mib update is scheduled */ - cancel_work_sync(&priv->mib_update_task); -@@ -1757,6 +1788,11 @@ static int __devinit bcm_enet_probe(stru - priv->pause_tx = pd->pause_tx; - priv->force_duplex_full = pd->force_duplex_full; - priv->force_speed_100 = pd->force_speed_100; -+ priv->dma_chan_en_mask = pd->dma_chan_en_mask; -+ priv->dma_chan_int_mask = pd->dma_chan_int_mask; -+ priv->dma_chan_width = pd->dma_chan_width; -+ priv->dma_no_sram = pd->dma_no_sram; -+ priv->dma_desc_shift = pd->dma_desc_shift; - } - - if (priv->mac_id == 0 && priv->has_phy && !priv->use_external_mii) { -@@ -2144,8 +2180,8 @@ static int bcm_enetsw_open(struct net_de - kdev = &priv->pdev->dev; - - /* mask all interrupts and request them */ -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, - IRQF_DISABLED, dev->name, dev); -@@ -2269,23 +2305,23 @@ static int bcm_enetsw_open(struct net_de - - /* write rx & tx ring addresses */ - enet_dmas_writel(priv, priv->rx_desc_dma, -- ENETDMAS_RSTART_REG(priv->rx_chan)); -+ ENETDMAS_RSTART_REG, priv->rx_chan); - enet_dmas_writel(priv, priv->tx_desc_dma, -- ENETDMAS_RSTART_REG(priv->tx_chan)); -+ ENETDMAS_RSTART_REG, priv->tx_chan); - - /* clear remaining state ram for rx & tx channel */ -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan)); -- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan)); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan); -+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan); - - /* set dma maximum burst len */ - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->rx_chan)); -+ ENETDMAC_MAXBURST, priv->rx_chan); - enet_dmac_writel(priv, priv->dma_maxburst, -- ENETDMAC_MAXBURST_REG(priv->tx_chan)); -+ ENETDMAC_MAXBURST, priv->tx_chan); - - /* set flow control low/high threshold to 1/3 / 2/3 */ - val = priv->rx_ring_size / 3; -@@ -2298,21 +2334,21 @@ static int bcm_enetsw_open(struct net_de - wmb(); - enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); - enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK, -- ENETDMAC_CHANCFG_REG(priv->rx_chan)); -+ ENETDMAC_CHANCFG, priv->rx_chan); - - /* watch "packet transferred" interrupt in rx and tx */ - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->rx_chan)); -+ ENETDMAC_IR, priv->rx_chan); - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IR_REG(priv->tx_chan)); -+ ENETDMAC_IR, priv->tx_chan); - - /* make sure we enable napi before rx interrupt */ - napi_enable(&priv->napi); - - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->rx_chan)); -+ ENETDMAC_IRMASK, priv->rx_chan); - enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK, -- ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ ENETDMAC_IRMASK, priv->tx_chan); - - netif_carrier_on(dev); - netif_start_queue(dev); -@@ -2419,8 +2455,8 @@ static int bcm_enetsw_stop(struct net_de - del_timer_sync(&priv->rx_timeout); - - /* mask all interrupts */ -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan)); -- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan)); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan); -+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan); - - /* disable dma & mac */ - bcm_enet_disable_dma(priv, priv->tx_chan); -@@ -2757,6 +2793,9 @@ static int __devinit bcm_enetsw_probe(st - memcpy(priv->used_ports, pd->used_ports, - sizeof (pd->used_ports)); - priv->num_ports = pd->num_ports; -+ priv->dma_chan_en_mask = pd->dma_chan_en_mask; -+ priv->dma_chan_int_mask = pd->dma_chan_int_mask; -+ priv->dma_chan_width = pd->dma_chan_width; - } - - ret = compute_hw_mtu(priv, dev->mtu); ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -367,6 +367,21 @@ struct bcm_enet_priv { - /* used to poll switch port state */ - struct timer_list swphy_poll; - spinlock_t enetsw_mdio_lock; -+ -+ /* dma channel enable mask */ -+ u32 dma_chan_en_mask; -+ -+ /* dma channel interrupt mask */ -+ u32 dma_chan_int_mask; -+ -+ /* dma engine has *no* internal SRAM */ -+ unsigned int dma_no_sram; -+ -+ /* dma channel width */ -+ unsigned int dma_chan_width; -+ -+ /* dma descriptor shift value */ -+ unsigned int dma_desc_shift; - }; - - static inline int bcm_enet_port_is_rgmii(int portid) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h -@@ -173,6 +173,7 @@ enum bcm63xx_regs_set { - #define BCM_6368_RSET_SPI_SIZE 1804 - #define RSET_ENET_SIZE 2048 - #define RSET_ENETDMA_SIZE 256 -+#define RSET_6345_ENETDMA_SIZE 64 - #define RSET_ENETDMAC_SIZE(chans) (16 * (chans)) - #define RSET_ENETDMAS_SIZE(chans) (16 * (chans)) - #define RSET_ENETSW_SIZE 65536 -@@ -299,7 +300,7 @@ enum bcm63xx_regs_set { - #define BCM_6345_USBDMA_BASE (0xfffe2800) - #define BCM_6345_ENET0_BASE (0xfffe1800) - #define BCM_6345_ENETDMA_BASE (0xfffe2800) --#define BCM_6345_ENETDMAC_BASE (0xfffe2900) -+#define BCM_6345_ENETDMAC_BASE (0xfffe2840) - #define BCM_6345_ENETDMAS_BASE (0xfffe2a00) - #define BCM_6345_ENETSW_BASE (0xdeadbeef) - #define BCM_6345_PCMCIA_BASE (0xfffe2028) ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h -@@ -4,6 +4,8 @@ - #include <linux/if_ether.h> - #include <linux/init.h> - -+#include <bcm63xx_regs.h> -+ - /* - * on board ethernet platform data - */ -@@ -37,6 +39,21 @@ struct bcm63xx_enet_platform_data { - int phy_id, int reg), - void (*mii_write)(struct net_device *dev, - int phy_id, int reg, int val)); -+ -+ /* DMA channel enable mask */ -+ u32 dma_chan_en_mask; -+ -+ /* DMA channel interrupt mask */ -+ u32 dma_chan_int_mask; -+ -+ /* Set to one if DMA engine has *no* SRAM */ -+ unsigned int dma_no_sram; -+ -+ /* DMA channel register width */ -+ unsigned int dma_chan_width; -+ -+ /* DMA descriptor shift */ -+ unsigned int dma_desc_shift; - }; - - /* -@@ -64,6 +81,15 @@ struct bcm63xx_enetsw_platform_data { - char mac_addr[ETH_ALEN]; - int num_ports; - struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; -+ -+ /* DMA channel enable mask */ -+ u32 dma_chan_en_mask; -+ -+ /* DMA channel interrupt mask */ -+ u32 dma_chan_int_mask; -+ -+ /* DMA channel register width */ -+ unsigned int dma_chan_width; - }; - - int __init bcm63xx_enet_register(int unit, -@@ -72,4 +98,66 @@ int __init bcm63xx_enet_register(int uni - int __init - bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd); - -+enum bcm63xx_regs_enetdmac { -+ ENETDMAC_CHANCFG, -+ ENETDMAC_IR, -+ ENETDMAC_IRMASK, -+ ENETDMAC_MAXBURST, -+ ENETDMAC_BUFALLOC, -+ ENETDMAC_RSTART, -+ ENETDMAC_FC, -+ ENETDMAC_LEN, -+}; -+ -+static inline unsigned long bcm63xx_enetdmacreg(enum bcm63xx_regs_enetdmac reg) -+{ -+#ifdef BCMCPU_RUNTIME_DETECT -+ extern const unsigned long *bcm63xx_regs_enetdmac; -+ -+ return bcm63xx_regs_enetdmac[reg]; -+#else -+#ifdef CONFIG_BCM63XX_CPU_6345 -+ switch (reg) { -+ case ENETDMAC_CHANCFG: -+ return ENETDMA_6345_CHANCFG_REG; -+ case ENETDMAC_IR: -+ return ENETDMA_6345_IR_REG; -+ case ENETDMAC_IRMASK: -+ return ENETDMA_6345_IRMASK_REG; -+ case ENETDMAC_MAXBURST: -+ return ENETDMA_6345_MAXBURST_REG; -+ case ENETDMAC_BUFALLOC: -+ return ENETDMA_6345_BUFALLOC_REG; -+ case ENETDMAC_RSTART: -+ return ENETDMA_6345_RSTART_REG; -+ case ENETDMAC_FC: -+ return ENETDMA_6345_FC_REG; -+ case ENETDMAC_LEN: -+ return ENETDMA_6345_LEN_REG; -+ } -+#endif -+#if defined(CONFIG_BCM6XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348) \ -+ defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6362) \ -+ defined(CONFIG_BCM63XX_CPU_6368) -+ switch (reg) { -+ case ENETDMAC_CHANCFG: -+ return ENETDMAC_CHANCFG_REG; -+ case ENETDMAC_IR: -+ return ENETDMAC_IR_REG; -+ case ENETDMAC_IRMASK: -+ return ENETDMAC_IRMASK_REG; -+ case ENETDMAC_MAXBURST: -+ return ENETDMAC_MAXBURST_REG; -+ case ENETDMAC_BUFALLOC: -+ case ENETDMAC_RSTART: -+ case ENETDMAC_FC: -+ case ENETDMAC_LEN: -+ return 0; -+ } -+#endif -+#endif -+ return 0; -+} -+ -+ - #endif /* ! BCM63XX_DEV_ENET_H_ */ diff --git a/target/linux/brcm63xx/patches-3.6/444-BCM63XX-add-endian-check-for-ath9k.patch b/target/linux/brcm63xx/patches-3.6/444-BCM63XX-add-endian-check-for-ath9k.patch deleted file mode 100644 index 6220a01133..0000000000 --- a/target/linux/brcm63xx/patches-3.6/444-BCM63XX-add-endian-check-for-ath9k.patch +++ /dev/null @@ -1,51 +0,0 @@ ---- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -@@ -2,6 +2,7 @@ - #define _PCI_ATH9K_FIXUP - - --void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init; -+void pci_enable_ath9k_fixup(unsigned slot, u32 offset, -+ unsigned endian_check) __init; - - #endif /* _PCI_ATH9K_FIXUP */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -18,6 +18,7 @@ - struct ath9k_caldata { - unsigned int slot; - u32 caldata_offset; -+ unsigned int endian_check:1; - }; - - /* ---- a/arch/mips/bcm63xx/pci-ath9k-fixup.c -+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c -@@ -172,12 +172,14 @@ static void ath9k_pci_fixup(struct pci_d - } - DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); - --void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset) -+void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset, -+ unsigned endian_check) - { - if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) - return; - - ath9k_fixups[ath9k_num_fixups].slot = slot; -+ ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check; - - if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) - return; ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -983,7 +983,8 @@ int __init board_register_devices(void) - - /* register any fixups */ - for (i = 0; i < board.has_caldata; i++) -- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset); -+ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, -+ board.caldata[i].endian_check); - - return 0; - } diff --git a/target/linux/brcm63xx/patches-3.6/445-BCM63XX-add-led-pin-for-ath9k.patch b/target/linux/brcm63xx/patches-3.6/445-BCM63XX-add-led-pin-for-ath9k.patch deleted file mode 100644 index 3a33549f99..0000000000 --- a/target/linux/brcm63xx/patches-3.6/445-BCM63XX-add-led-pin-for-ath9k.patch +++ /dev/null @@ -1,49 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -984,7 +984,7 @@ int __init board_register_devices(void) - /* register any fixups */ - for (i = 0; i < board.has_caldata; i++) - pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, -- board.caldata[i].endian_check); -+ board.caldata[i].endian_check, board.caldata[i].led_pin); - - return 0; - } ---- a/arch/mips/bcm63xx/pci-ath9k-fixup.c -+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c -@@ -173,13 +173,14 @@ static void ath9k_pci_fixup(struct pci_d - DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); - - void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset, -- unsigned endian_check) -+ unsigned endian_check, int led_pin) - { - if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) - return; - - ath9k_fixups[ath9k_num_fixups].slot = slot; - ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check; -+ ath9k_fixups[ath9k_num_fixups].pdata.led_pin = led_pin; - - if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) - return; ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -19,6 +19,7 @@ struct ath9k_caldata { - unsigned int slot; - u32 caldata_offset; - unsigned int endian_check:1; -+ int led_pin; - }; - - /* ---- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h -@@ -3,6 +3,6 @@ - - - void pci_enable_ath9k_fixup(unsigned slot, u32 offset, -- unsigned endian_check) __init; -+ unsigned endian_check, int led_pin) __init; - - #endif /* _PCI_ATH9K_FIXUP */ diff --git a/target/linux/brcm63xx/patches-3.6/446-BCM63XX-add-a-fixup-for-rt2x00-devices.patch b/target/linux/brcm63xx/patches-3.6/446-BCM63XX-add-a-fixup-for-rt2x00-devices.patch deleted file mode 100644 index 34ccc047bd..0000000000 --- a/target/linux/brcm63xx/patches-3.6/446-BCM63XX-add-a-fixup-for-rt2x00-devices.patch +++ /dev/null @@ -1,188 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -34,6 +34,7 @@ - #include <board_bcm963xx.h> - #include <linux/bcm963xx_tag.h> - #include <pci_ath9k_fixup.h> -+#include <pci_rt2x00_fixup.h> - - #define PFX "board_bcm963xx: " - -@@ -982,9 +983,19 @@ int __init board_register_devices(void) - } - - /* register any fixups */ -- for (i = 0; i < board.has_caldata; i++) -- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, -- board.caldata[i].endian_check, board.caldata[i].led_pin); -+ for (i = 0; i < board.has_caldata; i++) { -+ switch (board.caldata[i].vendor) { -+ case PCI_VENDOR_ID_ATHEROS: -+ pci_enable_ath9k_fixup(board.caldata[i].slot, -+ board.caldata[i].caldata_offset, board.caldata[i].endian_check, -+ board.caldata[i].led_pin); -+ break; -+ case PCI_VENDOR_ID_RALINK: -+ pci_enable_rt2x00_fixup(board.caldata[i].slot, -+ board.caldata[i].eeprom); -+ break; -+ } -+ } - - return 0; - } ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -146,7 +146,7 @@ static int __init bcm63xx_detect_flash_t - return 0; - } - --int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata) -+int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata) - { - u32 val; - unsigned int i; ---- a/arch/mips/bcm63xx/Makefile -+++ b/arch/mips/bcm63xx/Makefile -@@ -1,7 +1,8 @@ - obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o setup.o \ - timer.o dev-dsp.o dev-enet.o dev-flash.o dev-hsspi.o \ - dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-usb-ehci.o \ -- dev-usb-ohci.o dev-wdt.o pci-ath9k-fixup.o -+ dev-usb-ohci.o dev-wdt.o pci-ath9k-fixup.o \ -+ pci-rt2x00-fixup.o - obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - - obj-y += boards/ ---- /dev/null -+++ b/arch/mips/bcm63xx/pci-rt2x00-fixup.c -@@ -0,0 +1,71 @@ -+/* -+ * Broadcom BCM63XX RT2x00 EEPROM fixup helper. -+ * -+ * Copyright (C) 2012 Álvaro Fernández Rojas <noltari@gmail.com> -+ * -+ * Based on -+ * -+ * Broadcom BCM63XX Ath9k EEPROM fixup helper. -+ * -+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com> -+ * -+ * This program is free software; you can redistribute it and/or modify it -+ * under the terms of the GNU General Public License version 2 as published -+ * by the Free Software Foundation. -+ */ -+ -+#include <linux/pci.h> -+#include <linux/platform_device.h> -+#include <linux/rt2x00_platform.h> -+ -+#include <bcm63xx_nvram.h> -+#include <pci_rt2x00_fixup.h> -+ -+struct rt2x00_fixup { -+ unsigned slot; -+ u8 mac[ETH_ALEN]; -+ struct rt2x00_platform_data pdata; -+}; -+ -+static int rt2x00_num_fixups; -+static struct rt2x00_fixup rt2x00_fixups[2] = { -+ { -+ .slot = 255, -+ }, -+ { -+ .slot = 255, -+ }, -+}; -+ -+static void rt2x00_pci_fixup(struct pci_dev *dev) -+{ -+ unsigned i; -+ struct rt2x00_platform_data *pdata = NULL; -+ -+ for (i = 0; i < rt2x00_num_fixups; i++) { -+ if (rt2x00_fixups[i].slot != PCI_SLOT(dev->devfn)) -+ continue; -+ -+ pdata = &rt2x00_fixups[i].pdata; -+ break; -+ } -+ -+ dev->dev.platform_data = pdata; -+} -+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_RALINK, PCI_ANY_ID, rt2x00_pci_fixup); -+ -+void __init pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) -+{ -+ if (rt2x00_num_fixups >= ARRAY_SIZE(rt2x00_fixups)) -+ return; -+ -+ rt2x00_fixups[rt2x00_num_fixups].slot = slot; -+ rt2x00_fixups[rt2x00_num_fixups].pdata.eeprom_file_name = kstrdup(eeprom, GFP_KERNEL); -+ -+ if (bcm63xx_nvram_get_mac_address(rt2x00_fixups[rt2x00_num_fixups].mac)) -+ return; -+ -+ rt2x00_fixups[rt2x00_num_fixups].pdata.mac_address = rt2x00_fixups[rt2x00_num_fixups].mac; -+ rt2x00_num_fixups++; -+} -+ ---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h -@@ -11,6 +11,6 @@ enum { - - extern int bcm63xx_attached_flash; - --int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata); -+int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata); - - #endif /* __BCM63XX_FLASH_H */ ---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h -@@ -8,6 +8,7 @@ - #include <bcm63xx_dev_enet.h> - #include <bcm63xx_dev_dsp.h> - #include <pci_ath9k_fixup.h> -+#include <pci_rt2x00_fixup.h> - - /* - * flash mapping -@@ -15,11 +16,15 @@ - #define BCM963XX_CFE_VERSION_OFFSET 0x570 - #define BCM963XX_NVRAM_OFFSET 0x580 - --struct ath9k_caldata { -+struct bcm63xx_caldata { -+ unsigned int vendor; - unsigned int slot; - u32 caldata_offset; -+ /* Atheros */ - unsigned int endian_check:1; - int led_pin; -+ /* Ralink */ -+ char* eeprom; - }; - - /* -@@ -43,7 +48,7 @@ struct board_info { - unsigned int has_caldata:2; - - /* wifi calibration data config */ -- struct ath9k_caldata caldata[2]; -+ struct bcm63xx_caldata caldata[2]; - - /* ethernet config */ - struct bcm63xx_enet_platform_data enet0; ---- /dev/null -+++ b/arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h -@@ -0,0 +1,9 @@ -+#ifndef _PCI_RT2X00_FIXUP -+#define _PCI_RT2X00_FIXUP -+ -+#define PCI_VENDOR_ID_RALINK 0x1814 -+ -+void pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) __init; -+ -+#endif /* _PCI_RT2X00_FIXUP */ -+ diff --git a/target/linux/brcm63xx/patches-3.6/447-bcm63xx_enet_add_b53_support.patch b/target/linux/brcm63xx/patches-3.6/447-bcm63xx_enet_add_b53_support.patch deleted file mode 100644 index 93ef40945a..0000000000 --- a/target/linux/brcm63xx/patches-3.6/447-bcm63xx_enet_add_b53_support.patch +++ /dev/null @@ -1,169 +0,0 @@ ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h -@@ -364,6 +364,9 @@ struct bcm_enet_priv { - struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; - int sw_port_link[ENETSW_MAX_PORT]; - -+ /* platform device for associated switch */ -+ struct platform_device *b53_device; -+ - /* used to poll switch port state */ - struct timer_list swphy_poll; - spinlock_t enetsw_mdio_lock; ---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c -+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c -@@ -30,6 +30,7 @@ - #include <linux/dma-mapping.h> - #include <linux/platform_device.h> - #include <linux/if_vlan.h> -+#include <linux/platform_data/b53.h> - - #include <bcm63xx_dev_enet.h> - #include "bcm63xx_enet.h" -@@ -2013,7 +2014,8 @@ static int __devexit bcm_enet_remove(str - return 0; - } - --struct platform_driver bcm63xx_enet_driver = { -+ -+static struct platform_driver bcm63xx_enet_driver = { - .probe = bcm_enet_probe, - .remove = __devexit_p(bcm_enet_remove), - .driver = { -@@ -2022,6 +2024,42 @@ struct platform_driver bcm63xx_enet_driv - }, - }; - -+struct b53_platform_data bcm63xx_b53_pdata = { -+ .chip_id = 0x6300, -+ .big_endian = 1, -+}; -+ -+struct platform_device bcm63xx_b53_dev = { -+ .name = "b53-switch", -+ .id = -1, -+ .dev = { -+ .platform_data = &bcm63xx_b53_pdata, -+ }, -+}; -+ -+static int bcmenet_switch_register(struct bcm_enet_priv *priv, u16 port_mask) -+{ -+ int ret; -+ -+ bcm63xx_b53_pdata.regs = priv->base; -+ bcm63xx_b53_pdata.enabled_ports = port_mask; -+ bcm63xx_b53_pdata.alias = priv->net_dev->name; -+ -+ ret = platform_device_register(&bcm63xx_b53_dev); -+ if (!ret) -+ priv->b53_device = &bcm63xx_b53_dev; -+ -+ return ret; -+} -+ -+static void bcmenet_switch_unregister(struct bcm_enet_priv *priv) -+{ -+ if (priv->b53_device) -+ platform_device_unregister(&bcm63xx_b53_dev); -+ -+ priv->b53_device = NULL; -+} -+ - /* - * switch mii access callbacks - */ -@@ -2270,29 +2308,6 @@ static int bcm_enetsw_open(struct net_de - enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i)); - } - -- /* reset mib */ -- val = enetsw_readb(priv, ENETSW_GMCR_REG); -- val |= ENETSW_GMCR_RST_MIB_MASK; -- enetsw_writeb(priv, val, ENETSW_GMCR_REG); -- mdelay(1); -- val &= ~ENETSW_GMCR_RST_MIB_MASK; -- enetsw_writeb(priv, val, ENETSW_GMCR_REG); -- mdelay(1); -- -- /* force CPU port state */ -- val = enetsw_readb(priv, ENETSW_IMPOV_REG); -- val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; -- enetsw_writeb(priv, val, ENETSW_IMPOV_REG); -- -- /* enable switch forward engine */ -- val = enetsw_readb(priv, ENETSW_SWMODE_REG); -- val |= ENETSW_SWMODE_FWD_EN_MASK; -- enetsw_writeb(priv, val, ENETSW_SWMODE_REG); -- -- /* enable jumbo on all ports */ -- enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); -- enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); -- - /* initialize flow control buffer allocation */ - enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, - ENETDMA_BUFALLOC_REG(priv->rx_chan)); -@@ -2760,6 +2775,9 @@ static int __devinit bcm_enetsw_probe(st - struct bcm63xx_enetsw_platform_data *pd; - struct resource *res_mem; - int ret, irq_rx, irq_tx; -+ unsigned i, num_ports = 0; -+ u16 port_mask = BIT(8); -+ u8 val; - - /* stop if shared driver failed, assume driver->probe will be - * called in the same order we register devices (correct ?) */ -@@ -2847,6 +2865,43 @@ static int __devinit bcm_enetsw_probe(st - priv->pdev = pdev; - priv->net_dev = dev; - -+ /* reset mib */ -+ val = enetsw_readb(priv, ENETSW_GMCR_REG); -+ val |= ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ val &= ~ENETSW_GMCR_RST_MIB_MASK; -+ enetsw_writeb(priv, val, ENETSW_GMCR_REG); -+ mdelay(1); -+ -+ /* force CPU port state */ -+ val = enetsw_readb(priv, ENETSW_IMPOV_REG); -+ val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; -+ enetsw_writeb(priv, val, ENETSW_IMPOV_REG); -+ -+ /* enable switch forward engine */ -+ val = enetsw_readb(priv, ENETSW_SWMODE_REG); -+ val |= ENETSW_SWMODE_FWD_EN_MASK; -+ enetsw_writeb(priv, val, ENETSW_SWMODE_REG); -+ -+ /* enable jumbo on all ports */ -+ enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); -+ enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); -+ -+ for (i = 0; i < priv->num_ports; i++) { -+ struct bcm63xx_enetsw_port *port = &priv->used_ports[i]; -+ -+ if (!port->used) -+ continue; -+ -+ num_ports++; -+ port_mask |= BIT(i); -+ } -+ -+ /* only register if there is more than one external port */ -+ if (num_ports > 1) -+ bcmenet_switch_register(priv, port_mask); -+ - return 0; - - out_put_clk: -@@ -2877,6 +2932,9 @@ static int __devexit bcm_enetsw_remove(s - priv = netdev_priv(dev); - unregister_netdev(dev); - -+ /* remove switch */ -+ bcmenet_switch_unregister(priv); -+ - /* release device resources */ - iounmap(priv->base); - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); diff --git a/target/linux/brcm63xx/patches-3.6/500-board-D4PW.patch b/target/linux/brcm63xx/patches-3.6/500-board-D4PW.patch deleted file mode 100644 index e2be7acc65..0000000000 --- a/target/linux/brcm63xx/patches-3.6/500-board-D4PW.patch +++ /dev/null @@ -1,67 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -512,6 +512,56 @@ static struct board_info __initdata boar - - .has_ohci0 = 1, - }; -+ -+static struct board_info __initdata board_96348_D4PW = { -+ .name = "D-4P-W", -+ .expected_cpu_id = 0x6348, -+ -+ .has_enet1 = 1, -+ .has_pci = 1, -+ .has_uart0 = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "D-4P-W:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "D-4P-W::status", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "D-4P-W:green:internet", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "D-4P-W:red:internet", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 7, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -686,6 +736,7 @@ static const struct board_info __initdat - &board_DV201AMR, - &board_96348gw_a, - &board_rta1025w_16, -+ &board_96348_D4PW, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/501-board-NB4.patch b/target/linux/brcm63xx/patches-3.6/501-board-NB4.patch deleted file mode 100644 index ab06628290..0000000000 --- a/target/linux/brcm63xx/patches-3.6/501-board-NB4.patch +++ /dev/null @@ -1,650 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -15,6 +15,8 @@ - #include <linux/gpio_keys.h> - #include <linux/input.h> - #include <linux/spi/spi.h> -+#include <linux/spi/spi_gpio.h> -+#include <linux/spi/74x164.h> - #include <asm/addrspace.h> - #include <bcm63xx_board.h> - #include <bcm63xx_cpu.h> -@@ -44,6 +46,12 @@ - #define CFE_OFFSET_64K 0x10000 - #define CFE_OFFSET_128K 0x20000 - -+#define NB4_PID_OFFSET 0xff80 -+#define NB4_74X164_GPIO_BASE 64 -+#define NB4_SPI_GPIO_MOSI 7 -+#define NB4_SPI_GPIO_CLK 6 -+#define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) -+ - static struct board_info board; - - /* -@@ -711,6 +719,596 @@ static struct board_info __initdata boar - - .has_ohci0 = 1, - }; -+ -+struct spi_gpio_platform_data nb4_spi_gpio_data = { -+ .sck = NB4_SPI_GPIO_CLK, -+ .mosi = NB4_SPI_GPIO_MOSI, -+ .miso = SPI_GPIO_NO_MISO, -+ .num_chipselect = 1, -+}; -+ -+ -+static struct platform_device nb4_spi_gpio = { -+ .name = "spi_gpio", -+ .id = 1, -+ .dev = { -+ .platform_data = &nb4_spi_gpio_data, -+ }, -+}; -+ -+static struct platform_device * __initdata nb4_devices[] = { -+ &nb4_spi_gpio, -+}; -+ -+const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = { -+ .base = NB4_74X164_GPIO_BASE -+}; -+ -+static struct spi_board_info nb4_spi_devices[] = { -+ { -+ .modalias = "74x164", -+ .max_speed_hz = 781000, -+ .bus_num = 1, -+ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT, -+ .mode = SPI_MODE_0, -+ .platform_data = &nb4_74x164_platform_data -+ } -+}; -+ -+static struct board_info __initdata board_nb4_ser_r0 = { -+ .name = "NB4-SER-r0", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-SER-r0:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:traffic", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:wifi", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:red:service", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:green:service", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r0:blue:service", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_ser_r1 = { -+ .name = "NB4-SER-r1", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-SER-r1:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:traffic", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:wifi", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:red:service", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:green:service", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r1:blue:service", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_ser_r2 = { -+ .name = "NB4-SER-r2", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-SER-r2:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:traffic", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:wifi", -+ .gpio = 15, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:red:service", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:green:service", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-SER-r2:blue:service", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_fxc_r1 = { -+ .name = "NB4-FXC-r1", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-FXC-r1:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:traffic", -+ .gpio = 2, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:wifi", -+ .gpio = 15, -+ }, -+ { -+ .name = "NB4-FXC-r1:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r1:red:service", -+ .gpio = 29, -+ }, -+ { -+ .name = "NB4-FXC-r1:green:service", -+ .gpio = 30, -+ }, -+ { -+ .name = "NB4-FXC-r1:blue:service", -+ .gpio = 4, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; -+ -+static struct board_info __initdata board_nb4_fxc_r2 = { -+ .name = "NB4-FXC-r2", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "NB4-FXC-r2:white:adsl", -+ .gpio = NB4_74HC64_GPIO(4), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:traffic", -+ .gpio = 2, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:tel", -+ .gpio = NB4_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:tv", -+ .gpio = NB4_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:wifi", -+ .gpio = 15, -+ }, -+ { -+ .name = "NB4-FXC-r2:white:alarm", -+ .gpio = NB4_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "NB4-FXC-r2:red:service", -+ .gpio = 29, -+ }, -+ { -+ .name = "NB4-FXC-r2:green:service", -+ .gpio = 30, -+ }, -+ { -+ .name = "NB4-FXC-r2:blue:service", -+ .gpio = 4, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "service", -+ .gpio = 27, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "clip", -+ .gpio = 31, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ .devs = nb4_devices, -+ .num_devs = ARRAY_SIZE(nb4_devices), -+ .spis = nb4_spi_devices, -+ .num_spis = ARRAY_SIZE(nb4_spi_devices), -+}; - #endif - - /* -@@ -744,6 +1342,11 @@ static const struct board_info __initdat - &board_96358vw2, - &board_AGPFS0, - &board_DWVS0, -+ &board_nb4_ser_r0, -+ &board_nb4_ser_r1, -+ &board_nb4_ser_r2, -+ &board_nb4_fxc_r1, -+ &board_nb4_fxc_r2, - #endif - }; - -@@ -798,6 +1401,16 @@ static void __init boardid_fixup(u8 *boo - struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K); - char *board_name = (char *)bcm63xx_nvram_get_name(); - -+ if (BCMCPU_IS_6358() && (!strcmp(board_name, "96358VW"))) { -+ u8 *p = boot_addr + NB4_PID_OFFSET; -+ -+ /* Extract nb4 PID */ -+ if (!memcmp(p, "NB4-", 4)) { -+ memcpy(board_name, p, sizeof("NB4-XXX-rX")); -+ return; -+ } -+ } -+ - /* check if bcm_tag is at 64k offset */ - if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { - /* else try 128k */ diff --git a/target/linux/brcm63xx/patches-3.6/502-board-96338W2_E7T.patch b/target/linux/brcm63xx/patches-3.6/502-board-96338W2_E7T.patch deleted file mode 100644 index 767940a520..0000000000 --- a/target/linux/brcm63xx/patches-3.6/502-board-96338W2_E7T.patch +++ /dev/null @@ -1,51 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -183,6 +183,40 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_96338w2_e7t = { -+ .name = "96338W2_E7T", -+ .expected_cpu_id = 0x6338, -+ -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "96338W2_E7T:green:ppp", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "96338W2_E7T:green:ppp-fail", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "96338W2_E7T:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ -+ }, -+ }, -+}; - #endif - - /* -@@ -1321,6 +1355,7 @@ static const struct board_info __initdat - #ifdef CONFIG_BCM63XX_CPU_6338 - &board_96338gw, - &board_96338w, -+ &board_96338w2_e7t, - #endif - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, diff --git a/target/linux/brcm63xx/patches-3.6/503-board-CPVA642.patch b/target/linux/brcm63xx/patches-3.6/503-board-CPVA642.patch deleted file mode 100644 index 287b021543..0000000000 --- a/target/linux/brcm63xx/patches-3.6/503-board-CPVA642.patch +++ /dev/null @@ -1,109 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -710,6 +710,98 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_CPVA642 = { -+ .name = "CPVA642", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "CPVA642:red:power", -+ .gpio = 14, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:power", -+ .gpio = 11, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "CPVA642:red:wifi", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:wifi", -+ .gpio = 28, -+ .active_low = 0, -+ }, -+ { -+ .name = "CPVA642:red:link", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:link", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:ether", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:phone1", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:phone2", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA642:green:usb", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 37, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+ - static struct board_info __initdata board_AGPFS0 = { - .name = "AGPF-S0", - .expected_cpu_id = 0x6358, -@@ -1376,6 +1468,7 @@ static const struct board_info __initdat - &board_96358vw, - &board_96358vw2, - &board_AGPFS0, -+ &board_CPVA642, - &board_DWVS0, - &board_nb4_ser_r0, - &board_nb4_ser_r1, diff --git a/target/linux/brcm63xx/patches-3.6/504-board_dsl_274xb_rev_c.patch b/target/linux/brcm63xx/patches-3.6/504-board_dsl_274xb_rev_c.patch deleted file mode 100644 index 159deb03c5..0000000000 --- a/target/linux/brcm63xx/patches-3.6/504-board_dsl_274xb_rev_c.patch +++ /dev/null @@ -1,72 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -846,6 +846,61 @@ static struct board_info __initdata boar - .has_ohci0 = 1, - }; - -+/* D-Link DSL-274xB revison C2/C3 */ -+static struct board_info __initdata board_dsl_274xb_rev_c = { -+ .name = "AW4139", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "dsl-274xb:green:power", -+ .gpio = 5, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "dsl-274xb:red:power", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:adsl", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:internet", -+ .gpio = 2, -+ }, -+ { -+ .name = "dsl-274xb:red:internet", -+ .gpio = 10, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - struct spi_gpio_platform_data nb4_spi_gpio_data = { - .sck = NB4_SPI_GPIO_CLK, - .mosi = NB4_SPI_GPIO_MOSI, -@@ -1470,6 +1525,7 @@ static const struct board_info __initdat - &board_AGPFS0, - &board_CPVA642, - &board_DWVS0, -+ &board_dsl_274xb_rev_c, - &board_nb4_ser_r0, - &board_nb4_ser_r1, - &board_nb4_ser_r2, diff --git a/target/linux/brcm63xx/patches-3.6/505-board_spw500v.patch b/target/linux/brcm63xx/patches-3.6/505-board_spw500v.patch deleted file mode 100644 index 0a0ce13737..0000000000 --- a/target/linux/brcm63xx/patches-3.6/505-board_spw500v.patch +++ /dev/null @@ -1,78 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -604,6 +604,67 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_spw500v = { -+ .name = "SPW500V", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 6, -+ .gpio_int = 34, -+ .ext_irq = 2, -+ .cs = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "SPW500V:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "SPW500V:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "SPW500V:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { .name = "SPW500V:green:pstn", -+ .gpio = 28, -+ .active_low = 1, -+ }, -+ { -+ .name = "SPW500V:green:voip", -+ .gpio = 32, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -1517,6 +1578,7 @@ static const struct board_info __initdat - &board_96348gw_a, - &board_rta1025w_16, - &board_96348_D4PW, -+ &board_spw500v, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/506-board_gw6200_gw6000.patch b/target/linux/brcm63xx/patches-3.6/506-board_gw6200_gw6000.patch deleted file mode 100644 index 7b7f3cadcc..0000000000 --- a/target/linux/brcm63xx/patches-3.6/506-board_gw6200_gw6000.patch +++ /dev/null @@ -1,124 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -471,6 +471,112 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_gw6200 = { -+ .name = "GW6200", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 8, /* FIXME: What is real GPIO here? */ -+ .gpio_int = 34, -+ .ext_irq = 2, -+ .cs = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "GW6200:green:line1", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "GW6200:green:line2", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "GW6200:green:line3", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "GW6200:green:tel", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+static struct board_info __initdata board_gw6000 = { -+ .name = "GW6000", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 6, -+ .gpio_int = 34, -+ .ext_irq = 2, -+ .cs = 2, -+ }, -+ -+ /* GW6000 has no GPIO-controlled leds */ -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+ -+ - static struct board_info __initdata board_FAST2404 = { - .name = "F@ST2404", - .expected_cpu_id = 0x6348, -@@ -1571,6 +1677,8 @@ static const struct board_info __initdat - #ifdef CONFIG_BCM63XX_CPU_6348 - &board_96348r, - &board_96348gw, -+ &board_gw6000, -+ &board_gw6200, - &board_96348gw_10, - &board_96348gw_11, - &board_FAST2404, diff --git a/target/linux/brcm63xx/patches-3.6/507-board-MAGIC.patch b/target/linux/brcm63xx/patches-3.6/507-board-MAGIC.patch deleted file mode 100644 index 4d32bf23cf..0000000000 --- a/target/linux/brcm63xx/patches-3.6/507-board-MAGIC.patch +++ /dev/null @@ -1,89 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -771,6 +771,78 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_96348sv = { -+ .name = "MAGIC", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ /* it has BP_ENET_EXTERNAL_PHY */ -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .has_dsp = 1, -+ .dsp = { -+ .gpio_rst = 25, -+ .gpio_int = 34, -+ .cs = 2, -+ .ext_irq = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "MAGIC:green:voip", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:adsl", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:wifi", -+ .gpio = 28, -+ }, -+ { -+ .name = "MAGIC:green:usb", -+ .gpio = 35, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:hpna", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "MAGIC:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "MAGIC:green:stop", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ }, -+}; - #endif - - /* -@@ -1687,6 +1759,7 @@ static const struct board_info __initdat - &board_rta1025w_16, - &board_96348_D4PW, - &board_spw500v, -+ &board_96348sv, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/508-board_hw553.patch b/target/linux/brcm63xx/patches-3.6/508-board_hw553.patch deleted file mode 100644 index 4d40b2ba3c..0000000000 --- a/target/linux/brcm63xx/patches-3.6/508-board_hw553.patch +++ /dev/null @@ -1,93 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1729,6 +1729,82 @@ static struct board_info __initdata boar - .spis = nb4_spi_devices, - .num_spis = ARRAY_SIZE(nb4_spi_devices), - }; -+ -+static struct board_info __initdata board_HW553 = { -+ .name = "HW553", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "HW553:red:lan", -+ .gpio = 34, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:blue:lan", -+ .gpio = 35, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:adsl", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:blue:adsl", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:power", -+ .gpio = 5, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ -+ { -+ .name = "HW553:blue:power", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:wifi", -+ .gpio = 25, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:red:internetkey", -+ .gpio = 12, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW553:blue:internetkey", -+ .gpio = 13, -+ .active_low = 1, -+ }, -+ }, -+}; - #endif - - /* -@@ -1774,6 +1850,7 @@ static const struct board_info __initdat - &board_nb4_ser_r2, - &board_nb4_fxc_r1, - &board_nb4_fxc_r2, -+ &board_HW553, - #endif - }; - diff --git a/target/linux/brcm63xx/patches-3.6/509-board_rta1320_16m.patch b/target/linux/brcm63xx/patches-3.6/509-board_rta1320_16m.patch deleted file mode 100644 index 06d340e07d..0000000000 --- a/target/linux/brcm63xx/patches-3.6/509-board_rta1320_16m.patch +++ /dev/null @@ -1,56 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -217,6 +217,45 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_rta1320_16m = { -+ .name = "RTA1320_16M", -+ .expected_cpu_id = 0x6338, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "RTA1320_16M:green:adsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA1320_16M:green:ppp", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA1320_16M:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "RTA1320_16M:green:stop", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ }, -+}; - #endif - - /* -@@ -1818,6 +1857,7 @@ static const struct board_info __initdat - &board_96338gw, - &board_96338w, - &board_96338w2_e7t, -+ &board_rta1320_16m, - #endif - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, diff --git a/target/linux/brcm63xx/patches-3.6/510-board_spw303v.patch b/target/linux/brcm63xx/patches-3.6/510-board_spw303v.patch deleted file mode 100644 index e58b2265ce..0000000000 --- a/target/linux/brcm63xx/patches-3.6/510-board_spw303v.patch +++ /dev/null @@ -1,83 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1844,6 +1844,72 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+ /* T-Home Speedport W 303V Typ B */ -+static struct board_info __initdata board_spw303v = { -+ .name = "96358-502V", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "spw303v:green:power+adsl", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:red:power+adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:ppp", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:ses", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:voip", -+ .gpio = 27, -+ .active_low = 1, -+ }, -+ { -+ .name = "spw303v:green:pots", -+ .gpio = 31, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "ses", -+ .gpio = 37, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ } -+}; - #endif - - /* -@@ -1891,6 +1957,7 @@ static const struct board_info __initdat - &board_nb4_fxc_r1, - &board_nb4_fxc_r2, - &board_HW553, -+ &board_spw303v, - #endif - }; - diff --git a/target/linux/brcm63xx/patches-3.6/511-board_V2500V.patch b/target/linux/brcm63xx/patches-3.6/511-board_V2500V.patch deleted file mode 100644 index 90ea4ef635..0000000000 --- a/target/linux/brcm63xx/patches-3.6/511-board_V2500V.patch +++ /dev/null @@ -1,124 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -882,6 +882,65 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_V2500V_BB = { -+ .name = "V2500V_BB", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "V2500V_BB:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "V2500V_BB:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2500V_BB:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { .name = "V2500V_BB:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2500V_BB:green:wireless", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 31, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -1942,6 +2001,7 @@ static const struct board_info __initdat - &board_96348_D4PW, - &board_spw500v, - &board_96348sv, -+ &board_V2500V_BB, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 -@@ -2062,6 +2122,23 @@ void __init board_prom_init(void) - val &= MPI_CSBASE_BASE_MASK; - } - boot_addr = (u8 *)KSEG1ADDR(val); -+ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr); -+ -+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */ -+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/ -+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */ -+ /* Do an early check of CFE and then select bank 0 */ -+ -+ if (boot_addr == (u8 *)0xbf800000) { -+ unsigned char board_name[16]; -+ u8 *tmp_boot_addr; -+ tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0 -+ memcpy(board_name, tmp_boot_addr + BCM963XX_NVRAM_OFFSET + offsetof(struct bcm963xx_nvram, name), sizeof(board_name)); -+ if (!strcmp(board_name, "V2500V_BB")) { -+ printk(KERN_INFO PFX "V2500V: nvram bank 0\n"); -+ boot_addr = (u8 *)0xbfc00000; // Bank 0 -+ } -+ } - - /* dump cfe version */ - cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET; ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -19,6 +19,7 @@ - #include <linux/spi/spi.h> - #include <linux/spi/flash.h> - -+#include <bcm63xx_board.h> - #include <bcm63xx_cpu.h> - #include <bcm63xx_dev_flash.h> - #include <bcm63xx_dev_hsspi.h> -@@ -162,6 +163,13 @@ int __init bcm63xx_flash_register(int nu - val = bcm_mpi_readl(MPI_CSBASE_REG(0)); - val &= MPI_CSBASE_BASE_MASK; - -+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */ -+ /* Loading from CFE always uses Bank 0 */ -+ if (!strcmp(board_get_name(), "V2500V_BB")) { -+ pr_info("V2500V: Start in Bank 0\n"); -+ val = val + 0x400000; // Select Bank 0 start address -+ } -+ - mtd_resources[0].start = val; - mtd_resources[0].end = 0x1FFFFFFF; - diff --git a/target/linux/brcm63xx/patches-3.6/512-board_BTV2110.patch b/target/linux/brcm63xx/patches-3.6/512-board_BTV2110.patch deleted file mode 100644 index edde41a62f..0000000000 --- a/target/linux/brcm63xx/patches-3.6/512-board_BTV2110.patch +++ /dev/null @@ -1,75 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -442,6 +442,64 @@ static struct board_info __initdata boar - }, - }; - -+ -+/* BT Voyager 2110 */ -+static struct board_info __initdata board_V2110 = { -+ .name = "V2110", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "V2110:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "V2110:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2110:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { .name = "V2110:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "V2110:green:wireless", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ -+ - static struct board_info __initdata board_96348gw = { - .name = "96348GW", - .expected_cpu_id = 0x6348, -@@ -2002,6 +2060,7 @@ static const struct board_info __initdat - &board_spw500v, - &board_96348sv, - &board_V2500V_BB, -+ &board_V2110, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/513-board_livebox.patch b/target/linux/brcm63xx/patches-3.6/513-board_livebox.patch deleted file mode 100644 index 8089307cbf..0000000000 --- a/target/linux/brcm63xx/patches-3.6/513-board_livebox.patch +++ /dev/null @@ -1,389 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/Kconfig -+++ b/arch/mips/bcm63xx/boards/Kconfig -@@ -8,4 +8,10 @@ config BOARD_BCM963XX - select SSB - help - -+config BOARD_LIVEBOX -+ bool "Inventel Livebox(es) boards" -+ select SSB -+ help -+ Inventel Livebox boards using the RedBoot bootloader. -+ - endchoice ---- a/arch/mips/bcm63xx/boards/Makefile -+++ b/arch/mips/bcm63xx/boards/Makefile -@@ -1 +1,2 @@ - obj-$(CONFIG_BOARD_BCM963XX) += board_bcm963xx.o -+obj-$(CONFIG_BOARD_LIVEBOX) += board_livebox.o ---- /dev/null -+++ b/arch/mips/bcm63xx/boards/board_livebox.c -@@ -0,0 +1,368 @@ -+/* -+ * This file is subject to the terms and conditions of the GNU General Public -+ * License. See the file "COPYING" in the main directory of this archive -+ * for more details. -+ * -+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org> -+ */ -+ -+#include <linux/init.h> -+#include <linux/kernel.h> -+#include <linux/string.h> -+#include <linux/platform_device.h> -+#include <linux/mtd/mtd.h> -+#include <linux/mtd/partitions.h> -+#include <linux/mtd/physmap.h> -+#include <linux/ssb/ssb.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/spi/spi.h> -+#include <asm/addrspace.h> -+#include <bcm63xx_board.h> -+#include <bcm63xx_cpu.h> -+#include <bcm63xx_dev_uart.h> -+#include <bcm63xx_regs.h> -+#include <bcm63xx_io.h> -+#include <bcm63xx_dev_pci.h> -+#include <bcm63xx_dev_enet.h> -+#include <bcm63xx_dev_dsp.h> -+#include <bcm63xx_dev_pcmcia.h> -+#include <bcm63xx_dev_usb_ohci.h> -+#include <bcm63xx_dev_usb_ehci.h> -+#include <bcm63xx_dev_spi.h> -+#include <board_bcm963xx.h> -+ -+#define PFX "board_livebox: " -+ -+#define LIVEBOX_KEYS_POLL_INTERVAL 20 -+#define LIVEBOX_KEYS_DEBOUNCE_INTERVAL (LIVEBOX_KEYS_POLL_INTERVAL * 3) -+ -+static unsigned int mac_addr_used = 0; -+static struct board_info board; -+ -+/* -+ * known 6348 boards -+ */ -+#ifdef CONFIG_BCM63XX_CPU_6348 -+static struct board_info __initdata board_livebox_blue5g = { -+ .name = "Livebox-blue-5g", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 31, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ -+ .has_dsp = 0, /*TODO some Liveboxes have dsp*/ -+ .dsp = { -+ .gpio_rst = 6, /*FIXME eth1 shares gpio6 with dsp?*/ -+ .gpio_int = 35, -+ .cs = 2, -+ .ext_irq = 2, -+ }, -+ -+ .leds = { -+ { -+ .name = "Livebox-blue-5g::adsl-fail", -+ .gpio = 0, -+ .active_low = 0, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "Livebox-blue-5g::adsl", -+ .gpio = 1, -+ }, -+ { -+ .name = "Livebox-blue-5g::traffic", -+ .gpio = 2, -+ }, -+ { -+ .name = "Livebox-blue-5g::phone", -+ .gpio = 3, -+ }, -+ { -+ .name = "Livebox-blue-5g::wifi", -+ .gpio = 4, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "BTN_1", -+ .gpio = 36, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = BTN_1, -+ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "BTN_2", -+ .gpio = 7, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = BTN_2, -+ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ -+ }, -+}; -+#endif -+ -+/* -+ * all boards -+ */ -+static const struct board_info __initdata *bcm963xx_boards[] = { -+#ifdef CONFIG_BCM63XX_CPU_6348 -+ &board_livebox_blue5g -+#endif -+}; -+/* -+ * return board name for /proc/cpuinfo -+ */ -+const char *board_get_name(void) -+{ -+ return board.name; -+} -+ -+/* -+ * register & return a new board mac address -+ */ -+static int board_get_mac_address(u8 *mac) -+{ -+ u8 *p; -+ int count; -+ -+ memcpy(mac, (u8 *)0xBEBFF377, ETH_ALEN); -+ -+ p = mac + ETH_ALEN - 1; -+ count = mac_addr_used; -+ -+ while (count--) { -+ do { -+ (*p)++; -+ if (*p != 0) -+ break; -+ p--; -+ } while (p != mac); -+ } -+ -+ if (p == mac) { -+ printk(KERN_ERR PFX "unable to fetch mac address\n"); -+ return -ENODEV; -+ } -+ mac_addr_used++; -+ -+ return 0; -+} -+ -+/* -+ * early init callback -+ */ -+#define LIVEBOX_GPIO_DETECT_MASK 0x000000ff -+#define LIVEBOX_BOOT_ADDR 0x1e400000 -+ -+#define LIVEBOX_HW_BLUE5G_9 0x90 -+ -+void __init board_prom_init(void) -+{ -+ u32 val; -+ u8 hw_version; -+ -+ /* Get hardware version */ -+ val = bcm_gpio_readl(GPIO_CTL_LO_REG); -+ val &= ~LIVEBOX_GPIO_DETECT_MASK; -+ bcm_gpio_writel(val, GPIO_CTL_LO_REG); -+ -+ hw_version = bcm_gpio_readl(GPIO_DATA_LO_REG) & LIVEBOX_GPIO_DETECT_MASK; -+ switch (hw_version) { -+ case LIVEBOX_HW_BLUE5G_9: -+ printk(KERN_INFO PFX "Livebox BLUE5G.9\n"); -+ memcpy(&board, bcm963xx_boards[0], sizeof(board)); -+ break; -+ default: -+ printk(KERN_INFO PFX "Unknown livebox version: %02x\n", hw_version); -+ break; -+ } -+ -+ /* use default livebox configuration */ -+ memcpy(&board, bcm963xx_boards[0], sizeof(board)); -+ -+ /* setup pin multiplexing depending on board enabled device, -+ * this has to be done this early since PCI init is done -+ * inside arch_initcall */ -+ val = 0; -+ -+#ifdef CONFIG_PCI -+ if (board.has_pci) { -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G2_PCI; -+ } -+#endif -+ if (board.has_pccard) { -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G1_MII_PCCARD; -+ } -+ -+ if (board.has_enet0 && !board.enet0.use_internal_phy) { -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G3_EXT_MII | -+ GPIO_MODE_6348_G0_EXT_MII; -+ } -+ -+ if (board.has_enet1 && !board.enet1.use_internal_phy) { -+ if (BCMCPU_IS_6348()) -+ val |= GPIO_MODE_6348_G3_EXT_MII | -+ GPIO_MODE_6348_G0_EXT_MII; -+ printk(KERN_INFO PFX "resetting gpio6 for eth1...\n"); -+ gpio_request(6, "dsp_eth_rst"); -+ gpio_direction_output(6, 0); -+ gpio_set_value(6, 1); -+ } -+ -+ bcm_gpio_writel(val, GPIO_MODE_REG); -+} -+ -+/* -+ * second stage init callback, good time to panic if we couldn't -+ * identify on which board we're running since early printk is working -+ */ -+void __init board_setup(void) -+{ -+ if (!board.name[0]) -+ panic("unable to detect bcm963xx board"); -+ printk(KERN_INFO PFX "board name: %s\n", board.name); -+ -+ /* make sure we're running on expected cpu */ -+ if (bcm63xx_get_cpu_id() != board.expected_cpu_id) -+ panic("unexpected CPU for bcm963xx board"); -+} -+ -+static struct physmap_flash_data flash_data = { -+ .width = 2, -+}; -+ -+static struct resource mtd_resources[] = { -+ { -+ .start = 0, /* filled at runtime */ -+ .end = 0, /* filled at runtime */ -+ .flags = IORESOURCE_MEM, -+ } -+}; -+ -+static struct platform_device mtd_dev = { -+ .name = "physmap-flash", -+ .resource = mtd_resources, -+ .num_resources = ARRAY_SIZE(mtd_resources), -+ .dev = { -+ .platform_data = &flash_data, -+ }, -+}; -+ -+static struct gpio_led_platform_data bcm63xx_led_data; -+ -+static struct platform_device bcm63xx_gpio_leds = { -+ .name = "leds-gpio", -+ .id = 0, -+ .dev.platform_data = &bcm63xx_led_data, -+}; -+ -+static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = { -+ .poll_interval = LIVEBOX_KEYS_POLL_INTERVAL, -+}; -+ -+static struct platform_device bcm63xx_gpio_keys_device = { -+ .name = "gpio-keys-polled", -+ .id = 0, -+ .dev.platform_data = &bcm63xx_gpio_keys_data, -+}; -+ -+/* -+ * third stage init callback, register all board devices. -+ */ -+int __init board_register_devices(void) -+{ -+ u32 val; -+ int led_count = 0; -+ int button_count = 0; -+ -+ if (board.has_uart0) -+ bcm63xx_uart_register(0); -+ -+ if (board.has_uart1) -+ bcm63xx_uart_register(1); -+ -+ if (board.has_pccard) -+ bcm63xx_pcmcia_register(); -+ -+ if (board.has_enet0 && -+ !board_get_mac_address(board.enet0.mac_addr)) -+ bcm63xx_enet_register(0, &board.enet0); -+ -+ if (board.has_enet1 && -+ !board_get_mac_address(board.enet1.mac_addr)) -+ bcm63xx_enet_register(1, &board.enet1); -+ -+ if (board.has_ehci0) -+ bcm63xx_ehci_register(); -+ -+ if (board.has_ohci0) -+ bcm63xx_ohci_register(); -+ -+ if (board.has_dsp) -+ bcm63xx_dsp_register(&board.dsp); -+ -+ bcm63xx_spi_register(); -+ -+ if (board.num_devs) -+ platform_add_devices(board.devs, board.num_devs); -+ -+ if (board.num_spis) -+ spi_register_board_info(board.spis, board.num_spis); -+ -+ -+ /* read base address of boot chip select (0) */ -+ val = bcm_mpi_readl(MPI_CSBASE_REG(0)); -+ val &= MPI_CSBASE_BASE_MASK; -+ if (val != LIVEBOX_BOOT_ADDR) -+ printk(KERN_NOTICE PFX "flash address is: 0x%08x, forcing to: 0x%08x\n", -+ val, LIVEBOX_BOOT_ADDR); -+ mtd_resources[0].start = LIVEBOX_BOOT_ADDR; -+ mtd_resources[0].end = 0x1ebfffff; -+ -+ platform_device_register(&mtd_dev); -+ -+ /* count number of LEDs defined by this device */ -+ while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) -+ led_count++; -+ -+ bcm63xx_led_data.num_leds = led_count; -+ bcm63xx_led_data.leds = board.leds; -+ -+ platform_device_register(&bcm63xx_gpio_leds); -+ -+ /* count number of BUTTONs defined by this device */ -+ while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc) -+ button_count++; -+ -+ if (button_count) { -+ bcm63xx_gpio_keys_data.nbuttons = button_count; -+ bcm63xx_gpio_keys_data.buttons = board.buttons; -+ -+ platform_device_register(&bcm63xx_gpio_keys_device); -+ } -+ -+ return 0; -+} diff --git a/target/linux/brcm63xx/patches-3.6/514-board_ct536_ct5621.patch b/target/linux/brcm63xx/patches-3.6/514-board_ct536_ct5621.patch deleted file mode 100644 index 09f6762924..0000000000 --- a/target/linux/brcm63xx/patches-3.6/514-board_ct536_ct5621.patch +++ /dev/null @@ -1,62 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -500,6 +500,51 @@ static struct board_info __initdata boar - }; - - -+static struct board_info __initdata board_ct536_ct5621 = { -+ .name = "CT536_CT5621", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 0, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "CT536_CT5621:green:adsl-fail", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "CT536_CT5621:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_96348gw = { - .name = "96348GW", - .expected_cpu_id = 0x6348, -@@ -2061,6 +2106,7 @@ static const struct board_info __initdat - &board_96348sv, - &board_V2500V_BB, - &board_V2110, -+ &board_ct536_ct5621, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/515-board_DWV-S0_fixes.patch b/target/linux/brcm63xx/patches-3.6/515-board_DWV-S0_fixes.patch deleted file mode 100644 index 3320c4190b..0000000000 --- a/target/linux/brcm63xx/patches-3.6/515-board_DWV-S0_fixes.patch +++ /dev/null @@ -1,19 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1269,6 +1269,8 @@ static struct board_info __initdata boar - .name = "DWV-S0", - .expected_cpu_id = 0x6358, - -+ .has_uart0 = 1, -+ - .has_enet0 = 1, - .has_enet1 = 1, - .has_pci = 1, -@@ -1284,6 +1286,7 @@ static struct board_info __initdata boar - }, - - .has_ohci0 = 1, -+ .has_ehci0 = 1, - }; - - /* D-Link DSL-274xB revison C2/C3 */ diff --git a/target/linux/brcm63xx/patches-3.6/516-board_96348A-122.patch b/target/linux/brcm63xx/patches-3.6/516-board_96348A-122.patch deleted file mode 100644 index e10feca25e..0000000000 --- a/target/linux/brcm63xx/patches-3.6/516-board_96348A-122.patch +++ /dev/null @@ -1,80 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -545,6 +545,69 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_96348A_122 = { -+ .name = "96348A-122", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .leds = { -+ { -+ .name = "96348A-122:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96348A-122:red:alarm", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348A-122:green:wps", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 35, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_96348gw = { - .name = "96348GW", - .expected_cpu_id = 0x6348, -@@ -2110,6 +2173,7 @@ static const struct board_info __initdat - &board_V2500V_BB, - &board_V2110, - &board_ct536_ct5621, -+ &board_96348A_122, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/517-RTA1205W_16_uart_fixes.patch b/target/linux/brcm63xx/patches-3.6/517-RTA1205W_16_uart_fixes.patch deleted file mode 100644 index e8196ea801..0000000000 --- a/target/linux/brcm63xx/patches-3.6/517-RTA1205W_16_uart_fixes.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -810,6 +810,7 @@ static struct board_info __initdata boar - .name = "RTA1025W_16", - .expected_cpu_id = 0x6348, - -+ .has_uart0 = 1, - .has_enet0 = 1, - .has_enet1 = 1, - .has_pci = 1, diff --git a/target/linux/brcm63xx/patches-3.6/519_board_CPVA502plus.patch b/target/linux/brcm63xx/patches-3.6/519_board_CPVA502plus.patch deleted file mode 100644 index 8c1b0daea8..0000000000 --- a/target/linux/brcm63xx/patches-3.6/519_board_CPVA502plus.patch +++ /dev/null @@ -1,57 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1108,6 +1108,46 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_CPVA502plus = { -+ .name = "CPVA502+", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "CPVA502+:green:phone", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA502+:green:link", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "CPVA502+:green:feth1", /* FIXME:does gpio4 enable eth1 phy? */ -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ }, -+}; -+ - #endif - - /* -@@ -2175,6 +2215,7 @@ static const struct board_info __initdat - &board_V2110, - &board_ct536_ct5621, - &board_96348A_122, -+ &board_CPVA502plus, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/520-bcm63xx-add-support-for-96368MVWG-board.patch b/target/linux/brcm63xx/patches-3.6/520-bcm63xx-add-support-for-96368MVWG-board.patch deleted file mode 100644 index 4d2c8f0b58..0000000000 --- a/target/linux/brcm63xx/patches-3.6/520-bcm63xx-add-support-for-96368MVWG-board.patch +++ /dev/null @@ -1,128 +0,0 @@ -From eeacc2529942051504bc957726aa178671344421 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Wed, 20 Jan 2010 16:21:30 +0100 -Subject: [PATCH 32/63] bcm63xx: add support for 96368MVWG board. - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 95 ++++++++++++++++++++ - .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 2 + - 2 files changed, 97 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2182,6 +2182,78 @@ static struct board_info __initdata boar - #endif - - /* -+ * known 6368 boards -+ */ -+#ifdef CONFIG_BCM63XX_CPU_6368 -+static struct board_info __initdata board_96368mvwg = { -+ .name = "96368MVWG", -+ .expected_cpu_id = 0x6368, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "port1", -+ }, -+ -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "port2", -+ }, -+ -+ [4] = { -+ .used = 1, -+ .phy_id = 0x12, -+ .name = "port0", -+ }, -+ -+ [5] = { -+ .used = 1, -+ .phy_id = 0x11, -+ .name = "port3", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96368MVWG:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVWG:green:ppp", -+ .gpio = 5, -+ }, -+ { -+ .name = "96368MVWG:green:power", -+ .gpio = 22, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96368MVWG:green:wps", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVWG:green:ppp-fail", -+ .gpio = 31, -+ }, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+}; -+#endif -+ -+/* - * all boards - */ - static const struct board_info __initdata *bcm963xx_boards[] = { -@@ -2233,6 +2305,10 @@ static const struct board_info __initdat - &board_HW553, - &board_spw303v, - #endif -+ -+#ifdef CONFIG_BCM63XX_CPU_6368 -+ &board_96368mvwg, -+#endif - }; - - /* -@@ -2404,12 +2480,25 @@ void __init board_prom_init(void) - bcm63xx_pci_enabled = 1; - if (BCMCPU_IS_6348()) - val |= GPIO_MODE_6348_G2_PCI; -+ -+ if (BCMCPU_IS_6368()) -+ val |= GPIO_MODE_6368_PCI_REQ1 | -+ GPIO_MODE_6368_PCI_GNT1 | -+ GPIO_MODE_6368_PCI_INTB | -+ GPIO_MODE_6368_PCI_REQ0 | -+ GPIO_MODE_6368_PCI_GNT0; - } - #endif - - if (board.has_pccard) { - if (BCMCPU_IS_6348()) - val |= GPIO_MODE_6348_G1_MII_PCCARD; -+ -+ if (BCMCPU_IS_6368()) -+ val |= GPIO_MODE_6368_PCMCIA_CD1 | -+ GPIO_MODE_6368_PCMCIA_CD2 | -+ GPIO_MODE_6368_PCMCIA_VS1 | -+ GPIO_MODE_6368_PCMCIA_VS2; - } - - if (board.has_enet0 && !board.enet0.use_internal_phy) { diff --git a/target/linux/brcm63xx/patches-3.6/521-bcm63xx-add-support-for-96368MVNgr-board.patch b/target/linux/brcm63xx/patches-3.6/521-bcm63xx-add-support-for-96368MVNgr-board.patch deleted file mode 100644 index 63dd31b7ec..0000000000 --- a/target/linux/brcm63xx/patches-3.6/521-bcm63xx-add-support-for-96368MVNgr-board.patch +++ /dev/null @@ -1,92 +0,0 @@ -From f457fc2eb9bb915b5a4d251c7c68d4694cf07b01 Mon Sep 17 00:00:00 2001 -From: Maxime Bizon <mbizon@freebox.fr> -Date: Fri, 4 Nov 2011 12:33:48 +0100 -Subject: [PATCH 33/63] bcm63xx: add support for 96368MVNgr board. - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 67 +++++++++++++++++++++++++++++ - 1 files changed, 67 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2251,6 +2251,72 @@ static struct board_info __initdata boar - .has_ohci0 = 1, - .has_ehci0 = 1, - }; -+ -+static struct board_info __initdata board_96368mvngr = { -+ .name = "96368MVNgr", -+ .expected_cpu_id = 0x6368, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "port1", -+ }, -+ -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "port2", -+ }, -+ -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "port3", -+ }, -+ -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "port4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96368MVNgr:green:adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVNgr:green:inet", -+ .gpio = 5, -+ }, -+ { -+ .name = "96368MVNgr:green:power", -+ .gpio = 22, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96368MVNgr:green:wps", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "96368MVNgr:green:inet-fail", -+ .gpio = 3, -+ }, -+ }, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+}; - #endif - - /* -@@ -2308,6 +2374,7 @@ static const struct board_info __initdat - - #ifdef CONFIG_BCM63XX_CPU_6368 - &board_96368mvwg, -+ &board_96368mvngr, - #endif - }; - diff --git a/target/linux/brcm63xx/patches-3.6/522-MIPS-BCM63XX-add-96328avng-reference-board.patch b/target/linux/brcm63xx/patches-3.6/522-MIPS-BCM63XX-add-96328avng-reference-board.patch deleted file mode 100644 index 6d4a101ecd..0000000000 --- a/target/linux/brcm63xx/patches-3.6/522-MIPS-BCM63XX-add-96328avng-reference-board.patch +++ /dev/null @@ -1,67 +0,0 @@ -From c93c2bbf0cc96da5a47d77f01daf6c983cfe4216 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 29 May 2012 10:52:25 +0200 -Subject: [PATCH] MIPS: BCM63XX: add 96328avng reference board - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 77 +++++++++++++++++++++++++++++ - 1 files changed, 77 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -65,13 +65,45 @@ static struct board_info __initdata boar - .has_uart0 = 1, - .has_pci = 1, - -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ - .leds = { - { -- .name = "96328avng::ppp-fail", -+ .name = "96328avng::internet-fail", - .gpio = 2, - .active_low = 1, - }, - { -+ .name = "96328avng::dsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { - .name = "96328avng::power", - .gpio = 4, - .active_low = 1, -@@ -88,7 +120,7 @@ static struct board_info __initdata boar - .active_low = 1, - }, - { -- .name = "96328avng::ppp", -+ .name = "96328avng::internet", - .gpio = 11, - .active_low = 1, - }, diff --git a/target/linux/brcm63xx/patches-3.6/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch b/target/linux/brcm63xx/patches-3.6/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch deleted file mode 100644 index 061eb68ca2..0000000000 --- a/target/linux/brcm63xx/patches-3.6/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch +++ /dev/null @@ -1,96 +0,0 @@ -From f0649f7b7c672cf452a1796a1422bf615e1973f8 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Tue, 29 May 2012 11:01:12 +0200 -Subject: [PATCH] MIPS: BCM63XX: add 963281TAN reference board - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 71 +++++++++++++++++++++++++++++ - 1 files changed, 71 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -126,6 +126,76 @@ static struct board_info __initdata boar - }, - }, - }; -+ -+static struct board_info __initdata board_963281TAN = { -+ .name = "963281TAN", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "963281TAN::internet", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "963281TAN::internet-fail", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::power-fail", -+ .gpio = 8, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::wps", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281TAN::dsl", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ -+ }, -+}; - #endif - - /* -@@ -2357,6 +2427,7 @@ static struct board_info __initdata boar - static const struct board_info __initdata *bcm963xx_boards[] = { - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, -+ &board_963281TAN, - #endif - #ifdef CONFIG_BCM63XX_CPU_6338 - &board_96338gw, diff --git a/target/linux/brcm63xx/patches-3.6/524-board_dsl_274xb_rev_f.patch b/target/linux/brcm63xx/patches-3.6/524-board_dsl_274xb_rev_f.patch deleted file mode 100644 index 49d96a6598..0000000000 --- a/target/linux/brcm63xx/patches-3.6/524-board_dsl_274xb_rev_f.patch +++ /dev/null @@ -1,132 +0,0 @@ -From 66808f706b3dcd83a9f5157997ff478a880a2906 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jonas.gorski@gmail.com> -Date: Mon, 30 Apr 2012 09:10:51 +0200 -Subject: [PATCH 70/79] MIPS: BCM63XX: Add board definition for D-Link - DSL-274xB rev F1 - ---- - arch/mips/bcm63xx/boards/board_bcm963xx.c | 104 +++++++++++++++++++++++++++++ - 1 files changed, 104 insertions(+), 0 deletions(-) - ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -196,6 +196,111 @@ static struct board_info __initdata boar - - }, - }; -+ -+static struct board_info __initdata board_dsl_274xb_f1 = { -+ .name = "AW4339U", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_ATHEROS, -+ .caldata_offset = 0x7d1000, -+ .slot = 0, -+ .led_pin = -1, -+ }, -+ }, -+ -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 4", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 3", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 2", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 1", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "dsl-274xb:red:internet", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:dsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "dsl-274xb:red:power", -+ .gpio = 8, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:blue:wps", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "dsl-274xb:green:internet", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "wifi", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 24, -+ .active_low = 1, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -2428,6 +2533,7 @@ static const struct board_info __initdat - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, - &board_963281TAN, -+ &board_dsl_274xb_f1, - #endif - #ifdef CONFIG_BCM63XX_CPU_6338 - &board_96338gw, diff --git a/target/linux/brcm63xx/patches-3.6/525-board_96348w3.patch b/target/linux/brcm63xx/patches-3.6/525-board_96348w3.patch deleted file mode 100644 index eb0a514d06..0000000000 --- a/target/linux/brcm63xx/patches-3.6/525-board_96348w3.patch +++ /dev/null @@ -1,70 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1355,6 +1355,59 @@ static struct board_info __initdata boar - }, - }; - -+/* NetGear DG834G v4 */ -+static struct board_info __initdata board_96348W3 = { -+ .name = "96348W3", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .has_ohci0 = 1, -+ -+ .leds = { -+ { -+ .name = "96348W3:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96348W3:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348W3::adsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348W3::internet", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 6, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - #endif - - /* -@@ -2563,6 +2616,7 @@ static const struct board_info __initdat - &board_ct536_ct5621, - &board_96348A_122, - &board_CPVA502plus, -+ &board_96348W3, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.6/526-board_CT6373-1.patch b/target/linux/brcm63xx/patches-3.6/526-board_CT6373-1.patch deleted file mode 100644 index 6b8e40a517..0000000000 --- a/target/linux/brcm63xx/patches-3.6/526-board_CT6373-1.patch +++ /dev/null @@ -1,138 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -52,6 +52,13 @@ - #define NB4_SPI_GPIO_CLK 6 - #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) - -+#define CT6373_PID_OFFSET 0xff80 -+#define CT6373_74X164_GPIO_BASE 64 -+#define CT6373_SPI_GPIO_MOSI 7 -+#define CT6373_SPI_GPIO_CLK 6 -+#define CT6373_74HC64_GPIO(X) (CT6373_74X164_GPIO_BASE + (X)) -+ -+ - static struct board_info board; - - /* -@@ -2298,6 +2305,113 @@ static struct board_info __initdata boar - .num_spis = ARRAY_SIZE(nb4_spi_devices), - }; - -+ -+struct spi_gpio_platform_data ct6373_spi_gpio_data = { -+ .sck = CT6373_SPI_GPIO_CLK, -+ .mosi = CT6373_SPI_GPIO_MOSI, -+ .miso = SPI_GPIO_NO_MISO, -+ .num_chipselect = 1, -+}; -+ -+static struct platform_device ct6373_spi_gpio = { -+ .name = "spi_gpio", -+ .id = 1, -+ .dev = { -+ .platform_data = &ct6373_spi_gpio_data, -+ }, -+}; -+ -+static struct platform_device * __initdata ct6373_devices[] = { -+ &ct6373_spi_gpio, -+}; -+ -+const struct gen_74x164_chip_platform_data ct6373_74x164_platform_data = { -+ .base = CT6373_74X164_GPIO_BASE -+}; -+ -+static struct spi_board_info ct6373_spi_devices[] = { -+ { -+ .modalias = "74x164", -+ .max_speed_hz = 781000, -+ .bus_num = 1, -+ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT, -+ .mode = SPI_MODE_0, -+ .platform_data = &ct6373_74x164_platform_data -+ } -+}; -+ -+static struct board_info __initdata board_ct6373_1 = { -+ .name = "CT6373-1", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "CT6373-1:green:power", -+ .gpio = 0, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "CT6373-1:green:usb", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:wlan", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:adsl", -+ .gpio = CT6373_74HC64_GPIO(0), -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:line", -+ .gpio = CT6373_74HC64_GPIO(1), -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:fxs1", -+ .gpio = CT6373_74HC64_GPIO(2), -+ .active_low = 1, -+ }, -+ { -+ .name = "CT6373-1:green:fxs2", -+ .gpio = CT6373_74HC64_GPIO(3), -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 35, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+ -+ .devs = ct6373_devices, -+ .num_devs = ARRAY_SIZE(ct6373_devices), -+ .spis = ct6373_spi_devices, -+ .num_spis = ARRAY_SIZE(ct6373_spi_devices), -+}; -+ - static struct board_info __initdata board_HW553 = { - .name = "HW553", - .expected_cpu_id = 0x6358, -@@ -2631,6 +2745,7 @@ static const struct board_info __initdat - &board_nb4_ser_r2, - &board_nb4_fxc_r1, - &board_nb4_fxc_r2, -+ &board_ct6373_1, - &board_HW553, - &board_spw303v, - #endif diff --git a/target/linux/brcm63xx/patches-3.6/527-board_dva-g3810bn-tl-1.patch b/target/linux/brcm63xx/patches-3.6/527-board_dva-g3810bn-tl-1.patch deleted file mode 100644 index 202de74e37..0000000000 --- a/target/linux/brcm63xx/patches-3.6/527-board_dva-g3810bn-tl-1.patch +++ /dev/null @@ -1,84 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2553,6 +2553,73 @@ static struct board_info __initdata boar - }, - } - }; -+ -+/* D-Link DVA-G3810BN/TL */ -+static struct board_info __initdata board_DVAG3810BN = { -+ .name = "DVAG3810BN", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_enet0 = 1, -+ .has_enet1 = 1, -+ .has_pci = 1, -+ -+ .enet0 = { -+ .has_phy = 0, -+ .use_internal_phy = 1, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ -+ .has_ohci0 = 1, -+ .has_pccard = 1, -+ .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "DVAG3810BN::voip", -+ .gpio = 1, -+ }, -+ { -+ .name = "DVAG3810BN::dsl", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "DVAG3810BN::internet", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "DVAG3810BN::power", -+ .gpio = 4, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "DVAG3810BN::stop", -+ .gpio = 5, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -2748,6 +2815,7 @@ static const struct board_info __initdat - &board_ct6373_1, - &board_HW553, - &board_spw303v, -+ &board_DVAG3810BN, - #endif - - #ifdef CONFIG_BCM63XX_CPU_6368 diff --git a/target/linux/brcm63xx/patches-3.6/528-board_nb6.patch b/target/linux/brcm63xx/patches-3.6/528-board_nb6.patch deleted file mode 100644 index fac42179f8..0000000000 --- a/target/linux/brcm63xx/patches-3.6/528-board_nb6.patch +++ /dev/null @@ -1,146 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -17,6 +17,7 @@ - #include <linux/spi/spi.h> - #include <linux/spi/spi_gpio.h> - #include <linux/spi/74x164.h> -+#include <linux/rtl8367.h> - #include <asm/addrspace.h> - #include <bcm63xx_board.h> - #include <bcm63xx_cpu.h> -@@ -51,6 +52,8 @@ - #define NB4_SPI_GPIO_MOSI 7 - #define NB4_SPI_GPIO_CLK 6 - #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) -+#define NB6_GPIO_RTL8367_SDA 18 -+#define NB6_GPIO_RTL8367_SCK 20 - - #define CT6373_PID_OFFSET 0xff80 - #define CT6373_74X164_GPIO_BASE 64 -@@ -2622,6 +2625,103 @@ static struct board_info __initdata boar - }; - #endif - -+#ifdef CONFIG_BCM63XX_CPU_6362 -+static struct rtl8367_extif_config nb6_rtl8367_extif0_cfg = { -+ .mode = RTL8367_EXTIF_MODE_RGMII, -+ .txdelay = 1, -+ .rxdelay = 5, -+ .ability = { -+ .force_mode = 1, -+ .txpause = 1, -+ .rxpause = 1, -+ .link = 1, -+ .duplex = 1, -+ .speed = RTL8367_PORT_SPEED_1000, -+ }, -+}; -+ -+static struct rtl8367_platform_data nb6_rtl8367_data = { -+ .gpio_sda = NB6_GPIO_RTL8367_SDA, -+ .gpio_sck = NB6_GPIO_RTL8367_SCK, -+ .extif0_cfg = &nb6_rtl8367_extif0_cfg, -+}; -+ -+static struct platform_device nb6_rtl8367_device = { -+ .name = RTL8367_DRIVER_NAME, -+ .id = -1, -+ .dev = { -+ .platform_data = &nb6_rtl8367_data, -+ } -+}; -+ -+static struct platform_device * __initdata nb6_devices[] = { -+ &nb6_rtl8367_device, -+}; -+ -+static struct board_info __initdata board_nb6 = { -+ .name = "NB6", -+ .expected_cpu_id = 0x6362, -+ -+ .has_uart0 = 1, -+ -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [4] = { -+ .used = 1, -+ .phy_id = 0xff, -+ .bypass_link = 1, -+ .force_speed = 1000, -+ .force_duplex_full = 1, -+ .name = "RGMII", -+ }, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 24, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 25, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 12, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ { -+ .desc = "service", -+ .gpio = 10, -+ .type = EV_KEY, -+ .code = BTN_0, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ .active_low = 1, -+ }, -+ }, -+ -+ .devs = nb6_devices, -+ .num_devs = ARRAY_SIZE(nb6_devices), -+}; -+#endif -+ - /* - * known 6368 boards - */ -@@ -2818,6 +2918,10 @@ static const struct board_info __initdat - &board_DVAG3810BN, - #endif - -+#ifdef CONFIG_BCM63XX_CPU_6362 -+ &board_nb6, -+#endif -+ - #ifdef CONFIG_BCM63XX_CPU_6368 - &board_96368mvwg, - &board_96368mvngr, -@@ -2885,6 +2989,11 @@ static void __init boardid_fixup(u8 *boo - } - } - -+ if (BCMCPU_IS_6362() && (!strncmp(board_name, "NB6-", sizeof("NB6-") - 1))) { -+ board_name[sizeof("NB6") - 1] = '\0'; -+ return ; -+ } -+ - /* check if bcm_tag is at 64k offset */ - if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) { - /* else try 128k */ diff --git a/target/linux/brcm63xx/patches-3.6/529-board_fast2604.patch b/target/linux/brcm63xx/patches-3.6/529-board_fast2604.patch deleted file mode 100644 index f09472e79b..0000000000 --- a/target/linux/brcm63xx/patches-3.6/529-board_fast2604.patch +++ /dev/null @@ -1,68 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1023,6 +1023,57 @@ static struct board_info __initdata boar - .has_ehci0 = 1, - }; - -+static struct board_info __initdata board_FAST2604 = { -+ .name = "F@ST2604", -+ .expected_cpu_id = 0x6348, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "F@ST2604:green:power", -+ .gpio = 0, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "F@ST2604:red:power", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "F@ST2604:red:inet", -+ .gpio = 4, -+ .active_low = 1, -+ }, -+ { -+ .name = "F@ST2604:green:wps", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ }, -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 33, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_rta1025w_16 = { - .name = "RTA1025W_16", - .expected_cpu_id = 0x6348, -@@ -2886,6 +2937,7 @@ static const struct board_info __initdat - &board_96348gw_10, - &board_96348gw_11, - &board_FAST2404, -+ &board_FAST2604, - &board_DV201AMR, - &board_96348gw_a, - &board_rta1025w_16, diff --git a/target/linux/brcm63xx/patches-3.6/530-board_963281T_TEF.patch b/target/linux/brcm63xx/patches-3.6/530-board_963281T_TEF.patch deleted file mode 100644 index 19559d9ab5..0000000000 --- a/target/linux/brcm63xx/patches-3.6/530-board_963281T_TEF.patch +++ /dev/null @@ -1,136 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -207,6 +207,125 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_963281T_TEF = { -+ .name = "963281T_TEF", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "963281T_TEF:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "963281T_TEF:red:power", -+ .gpio = 8, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:inet", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:inet", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:ppp", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:ppp", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:3g", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:3g", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:wlan", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:wlan", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:green:eth", -+ .gpio = 31, -+ .active_low = 1, -+ }, -+ { -+ .name = "963281T_TEF:red:eth", -+ .gpio = 20, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 24, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_dsl_274xb_f1 = { - .name = "AW4339U", - .expected_cpu_id = 0x6328, -@@ -2918,6 +3037,7 @@ static const struct board_info __initdat - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, - &board_963281TAN, -+ &board_963281T_TEF, - &board_dsl_274xb_f1, - #endif - #ifdef CONFIG_BCM63XX_CPU_6338 diff --git a/target/linux/brcm63xx/patches-3.6/531-board_96328A-1441N1.patch b/target/linux/brcm63xx/patches-3.6/531-board_96328A-1441N1.patch deleted file mode 100644 index c6205362ab..0000000000 --- a/target/linux/brcm63xx/patches-3.6/531-board_96328A-1441N1.patch +++ /dev/null @@ -1,89 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -137,6 +137,78 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_96328A_1441N1 = { -+ .name = "96328A-1441N1", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96328A-1441N1:green:power", -+ .gpio = 8, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96328A-1441N1:red:power", -+ .gpio = 4, -+ }, -+ { -+ .name = "96328A-1441N1:green:inet", -+ .gpio = 7, -+ }, -+ { -+ .name = "96328A-1441N1:red:inet", -+ .gpio = 1, -+ }, -+ { -+ .name = "96328A-1441N1:green:dsl", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_963281TAN = { - .name = "963281TAN", - .expected_cpu_id = 0x6328, -@@ -3036,6 +3108,7 @@ static struct board_info __initdata boar - static const struct board_info __initdata *bcm963xx_boards[] = { - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, -+ &board_96328A_1441N1, - &board_963281TAN, - &board_963281T_TEF, - &board_dsl_274xb_f1, diff --git a/target/linux/brcm63xx/patches-3.6/532-board_96328a-1241N.patch b/target/linux/brcm63xx/patches-3.6/532-board_96328a-1241N.patch deleted file mode 100644 index 674f50fd31..0000000000 --- a/target/linux/brcm63xx/patches-3.6/532-board_96328a-1241N.patch +++ /dev/null @@ -1,83 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -137,6 +137,72 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_96328A_1241N = { -+ .name = "96328A-1241N", -+ .expected_cpu_id = 0x6328, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ .has_enetsw = 1, -+ -+ .enetsw = { -+ .used_ports = { -+ [0] = { -+ .used = 1, -+ .phy_id = 1, -+ .name = "Port 1", -+ }, -+ [1] = { -+ .used = 1, -+ .phy_id = 2, -+ .name = "Port 2", -+ }, -+ [2] = { -+ .used = 1, -+ .phy_id = 3, -+ .name = "Port 3", -+ }, -+ [3] = { -+ .used = 1, -+ .phy_id = 4, -+ .name = "Port 4", -+ }, -+ }, -+ }, -+ -+ .leds = { -+ { -+ .name = "96328A-1241N:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "96328A-1241N:red:alarm", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "96328A-1241N:green:inet", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 23, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - static struct board_info __initdata board_96328A_1441N1 = { - .name = "96328A-1441N1", - .expected_cpu_id = 0x6328, -@@ -3108,6 +3174,7 @@ static struct board_info __initdata boar - static const struct board_info __initdata *bcm963xx_boards[] = { - #ifdef CONFIG_BCM63XX_CPU_6328 - &board_96328avng, -+ &board_96328A_1241N, - &board_96328A_1441N1, - &board_963281TAN, - &board_963281T_TEF, diff --git a/target/linux/brcm63xx/patches-3.6/550-alice_gate2_leds.patch b/target/linux/brcm63xx/patches-3.6/550-alice_gate2_leds.patch deleted file mode 100644 index e98e96b4bb..0000000000 --- a/target/linux/brcm63xx/patches-3.6/550-alice_gate2_leds.patch +++ /dev/null @@ -1,102 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1945,6 +1945,99 @@ static struct board_info __initdata boar - - .has_ohci0 = 1, - .has_ehci0 = 1, -+ -+ .leds = { -+ { -+ .name = "AGPF-S0:red:power", -+ .gpio = 5, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:power", -+ .gpio = 4, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "AGPF-S0:red:service", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:service", -+ .gpio = 6, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:adsl", -+ .gpio = 9, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:adsl", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:wifi", -+ .gpio = 23, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:wifi", -+ .gpio = 22, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:internet", -+ .gpio = 25, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:internet", -+ .gpio = 24, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:usr1", -+ .gpio = 27, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:usr1", -+ .gpio = 26, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:red:usr2", -+ .gpio = 30, -+ .active_low = 1, -+ }, -+ { -+ .name = "AGPF-S0:green:usr2", -+ .gpio = 29, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 37, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wps", -+ .gpio = 34, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WPS_BUTTON, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_DWVS0 = { diff --git a/target/linux/brcm63xx/patches-3.6/551-96348gw_a_leds.patch b/target/linux/brcm63xx/patches-3.6/551-96348gw_a_leds.patch deleted file mode 100644 index 562f3b5b7b..0000000000 --- a/target/linux/brcm63xx/patches-3.6/551-96348gw_a_leds.patch +++ /dev/null @@ -1,22 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -1390,6 +1390,19 @@ static struct board_info __initdata boar - }, - - .has_ohci0 = 1, -+ -+ .leds = { -+ { -+ .name = "96348GW-A::adsl", -+ .gpio = 3, -+ .active_low = 1, -+ }, -+ { -+ .name = "96348GW-A::usb", -+ .gpio = 0, -+ .active_low = 1, -+ } -+ }, - }; - - static struct board_info __initdata board_96348_D4PW = { diff --git a/target/linux/brcm63xx/patches-3.6/552-board_96348gw-10_reset_button.patch b/target/linux/brcm63xx/patches-3.6/552-board_96348gw-10_reset_button.patch deleted file mode 100644 index 4904f2f3a8..0000000000 --- a/target/linux/brcm63xx/patches-3.6/552-board_96348gw-10_reset_button.patch +++ /dev/null @@ -1,20 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -850,6 +850,17 @@ static struct board_info __initdata boar - .active_low = 1, - }, - }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 6, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, - }; - - static struct board_info __initdata board_96348gw_11 = { diff --git a/target/linux/brcm63xx/patches-3.6/553-board_rta770bw.patch b/target/linux/brcm63xx/patches-3.6/553-board_rta770bw.patch deleted file mode 100644 index 80df53365b..0000000000 --- a/target/linux/brcm63xx/patches-3.6/553-board_rta770bw.patch +++ /dev/null @@ -1,66 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -742,6 +742,55 @@ static struct board_info __initdata boar - - .has_uart0 = 1, - }; -+ -+static struct board_info __initdata board_rta770bw = { -+ .name = "RTA770BW", -+ .expected_cpu_id = 0x6345, -+ -+ .has_uart0 = 1, -+ -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "RTA770BW:green:usb", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770BW:green:adsl", -+ .gpio = 8, -+ }, -+ { -+ .name = "RTA770BW:green:diag", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770BW:green:wlan", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 13, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -3305,6 +3354,7 @@ static const struct board_info __initdat - #endif - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, -+ &board_rta770bw, - #endif - #ifdef CONFIG_BCM63XX_CPU_6348 - &board_96348r, diff --git a/target/linux/brcm63xx/patches-3.6/554-board_hw556.patch b/target/linux/brcm63xx/patches-3.6/554-board_hw556.patch deleted file mode 100644 index d084664dcb..0000000000 --- a/target/linux/brcm63xx/patches-3.6/554-board_hw556.patch +++ /dev/null @@ -1,447 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -2965,6 +2965,374 @@ static struct board_info __initdata boar - }, - }; - -+static struct board_info __initdata board_HW556 = { -+ .name = "HW556", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .caldata_offset = 0xe00000, -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:red:message", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:all", -+ .gpio = 6, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+static struct board_info __initdata board_HW556_A = { -+ .name = "HW556_A", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_RALINK, -+ .caldata_offset = 0xeffe00, -+ .slot = 1, -+ .eeprom = "rt2x00.eeprom", -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:red:message", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:all", -+ .gpio = 6, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+static struct board_info __initdata board_HW556_B = { -+ .name = "HW556_B", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_ATHEROS, -+ .caldata_offset = 0xf7e000, -+ .slot = 1, -+ .endian_check = 1, -+ .led_pin = 2, -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:red:message", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:all", -+ .gpio = 6, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+static struct board_info __initdata board_HW556_C = { -+ .name = "HW556_C", -+ .expected_cpu_id = 0x6358, -+ -+ .has_uart0 = 1, -+ .has_pci = 1, -+ .has_ohci0 = 1, -+ .has_ehci0 = 1, -+ -+ .has_caldata = 1, -+ .caldata = { -+ { -+ .vendor = PCI_VENDOR_ID_ATHEROS, -+ .caldata_offset = 0xefe000, -+ .slot = 1, -+ .endian_check = 1, -+ .led_pin = 2, -+ }, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "HW556:red:message", -+ .gpio = 0, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:hspa", -+ .gpio = 1, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:dsl", -+ .gpio = 2, -+ .active_low = 1, -+ }, -+ { -+ .name = "HW556:red:power", -+ .gpio = 3, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ { -+ .name = "HW556:red:all", -+ .gpio = 6, -+ .active_low = 1, -+ .default_trigger = "default-on", -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "help", -+ .gpio = 8, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_HELP, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "wlan", -+ .gpio = 9, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_WLAN, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "restart", -+ .gpio = 10, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ { -+ .desc = "reset", -+ .gpio = 11, -+ .active_low = 1, -+ .type = EV_KEY, -+ .code = KEY_CONFIG, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; -+ - /* T-Home Speedport W 303V Typ B */ - static struct board_info __initdata board_spw303v = { - .name = "96358-502V", -@@ -3393,6 +3761,10 @@ static const struct board_info __initdat - &board_nb4_fxc_r2, - &board_ct6373_1, - &board_HW553, -+ &board_HW556, -+ &board_HW556_A, -+ &board_HW556_B, -+ &board_HW556_C, - &board_spw303v, - &board_DVAG3810BN, - #endif -@@ -3458,13 +3830,37 @@ static void __init boardid_fixup(u8 *boo - struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K); - char *board_name = (char *)bcm63xx_nvram_get_name(); - -- if (BCMCPU_IS_6358() && (!strcmp(board_name, "96358VW"))) { -- u8 *p = boot_addr + NB4_PID_OFFSET; -- -- /* Extract nb4 PID */ -- if (!memcmp(p, "NB4-", 4)) { -- memcpy(board_name, p, sizeof("NB4-XXX-rX")); -- return; -+ if (BCMCPU_IS_6358()) { -+ if (!strcmp(board_name, "96358VW")) { -+ u8 *p = boot_addr + NB4_PID_OFFSET; -+ -+ /* Extract nb4 PID */ -+ if (!memcmp(p, "NB4-", 4)) { -+ memcpy(board_name, p, sizeof("NB4-XXX-rX")); -+ return; -+ } -+ } else if (!strcmp(board_name, "HW556")) { -+ /* -+ * HW556 has different wlan caldatas depending on -+ * hardware version. -+ * Detect hardware version and change board id -+ */ -+ u8 cal_data_ath9k[4] = { 0xa5, 0x5a, 0, 0 }; -+ u8 cal_data_rt3062[4] = { 0x62, 0x30, 1, 0 }; -+ -+ if (!memcmp(boot_addr + 0xeffe00, -+ &cal_data_rt3062, 4)) { -+ /* Ralink 0xeffe00 */ -+ memcpy(board_name, "HW556_A", 7); -+ } else if (!memcmp(boot_addr + 0xf7e000, -+ &cal_data_ath9k, 4)) { -+ /* Atheros 0xf7e000 */ -+ memcpy(board_name, "HW556_B", 7); -+ } else if (!memcmp(boot_addr + 0xefe000, -+ &cal_data_ath9k, 4)) { -+ /* Atheros 0xefe000 */ -+ memcpy(board_name, "HW556_C", 7); -+ } - } - } - ---- a/drivers/mtd/bcm63xxpart.c -+++ b/drivers/mtd/bcm63xxpart.c -@@ -93,6 +93,11 @@ static int bcm63xx_parse_cfe_partitions( - BCM63XX_CFE_BLOCK_SIZE); - - cfelen = cfe_erasesize; -+ -+ /* Fix HW556 MX29LV128DB */ -+ if (!strncmp(bcm63xx_nvram_get_name(), "HW556", 5)) -+ cfelen = 0x20000; -+ - nvramlen = bcm63xx_nvram_get_psi_size() * 1024; - nvramlen = roundup(nvramlen, cfe_erasesize); - nvramaddr = master->size - nvramlen; diff --git a/target/linux/brcm63xx/patches-3.6/555-boards_probe_switch.patch b/target/linux/brcm63xx/patches-3.6/555-boards_probe_switch.patch deleted file mode 100644 index 5994b1b851..0000000000 --- a/target/linux/brcm63xx/patches-3.6/555-boards_probe_switch.patch +++ /dev/null @@ -1,119 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -581,6 +581,8 @@ static struct board_info __initdata boar - .has_uart0 = 1, - .has_enet0 = 1, - .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -624,6 +626,8 @@ static struct board_info __initdata boar - .has_uart0 = 1, - .has_enet0 = 1, - .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -855,6 +859,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -927,6 +933,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1156,6 +1164,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1331,6 +1341,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1405,6 +1417,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1426,6 +1440,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1445,6 +1461,8 @@ static struct board_info __initdata boar - .use_internal_phy = 1, - }, - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1820,6 +1838,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -1872,6 +1892,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -2012,6 +2034,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, -@@ -2129,6 +2153,8 @@ static struct board_info __initdata boar - }, - - .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, - .force_speed_100 = 1, - .force_duplex_full = 1, - }, diff --git a/target/linux/brcm63xx/patches-3.6/556-board_rta770w.patch b/target/linux/brcm63xx/patches-3.6/556-board_rta770w.patch deleted file mode 100644 index e0eedad1e7..0000000000 --- a/target/linux/brcm63xx/patches-3.6/556-board_rta770w.patch +++ /dev/null @@ -1,71 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -796,6 +796,60 @@ - }, - }, - }; -+ -+// Actually this board is the very same as the rta770bw, -+// where the additional 'b' within the name just -+// just indicates 'Annex B'. The ADSL Modem itself is able -+// to handle both Annex A as well as Annex B - -+// the loaded firmware makes the only difference -+static struct board_info __initdata board_rta770w = { -+ .name = "RTA770W", -+ .expected_cpu_id = 0x6345, -+ -+ .has_uart0 = 1, -+ -+ .has_enet0 = 1, -+ -+ .enet0 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+ -+ .leds = { -+ { -+ .name = "RTA770W:green:usb", -+ .gpio = 7, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770W:green:adsl", -+ .gpio = 8, -+ }, -+ { -+ .name = "RTA770W:green:diag", -+ .gpio = 10, -+ .active_low = 1, -+ }, -+ { -+ .name = "RTA770W:green:wlan", -+ .gpio = 11, -+ .active_low = 1, -+ }, -+ }, -+ -+ .buttons = { -+ { -+ .desc = "reset", -+ .gpio = 13, -+ .type = EV_KEY, -+ .code = KEY_RESTART, -+ .active_low = 1, -+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, -+ }, -+ }, -+}; - #endif - - /* -@@ -3750,6 +3804,7 @@ - #ifdef CONFIG_BCM63XX_CPU_6345 - &board_96345gw2, - &board_rta770bw, -+ &board_rta770w, - #endif - #ifdef CONFIG_BCM63XX_CPU_6348 - &board_96348r, diff --git a/target/linux/brcm63xx/patches-3.6/800-wl_exports.patch b/target/linux/brcm63xx/patches-3.6/800-wl_exports.patch deleted file mode 100644 index 0fff4d0b1b..0000000000 --- a/target/linux/brcm63xx/patches-3.6/800-wl_exports.patch +++ /dev/null @@ -1,34 +0,0 @@ ---- a/arch/mips/bcm63xx/nvram.c -+++ b/arch/mips/bcm63xx/nvram.c -@@ -19,6 +19,13 @@ - static struct bcm963xx_nvram nvram; - static int mac_addr_used; - -+/* -+ * Required export for WL -+ */ -+#define NVRAM_SPACE 0x8000 -+char nvram_buf[NVRAM_SPACE]; -+EXPORT_SYMBOL(nvram_buf); -+ - int __init bcm63xx_nvram_init(void *addr) - { - unsigned int check_len; -@@ -27,6 +34,7 @@ int __init bcm63xx_nvram_init(void *addr - - /* extract nvram data */ - memcpy(&nvram, addr, sizeof(nvram)); -+ memcpy(&nvram_buf, addr, NVRAM_SPACE); - - /* check checksum before using data */ - if (nvram.version <= 4) ---- a/arch/mips/mm/cache.c -+++ b/arch/mips/mm/cache.c -@@ -58,6 +58,7 @@ void (*_dma_cache_wback)(unsigned long s - void (*_dma_cache_inv)(unsigned long start, unsigned long size); - - EXPORT_SYMBOL(_dma_cache_wback_inv); -+EXPORT_SYMBOL(_dma_cache_inv); - - #endif /* CONFIG_DMA_NONCOHERENT */ - diff --git a/target/linux/brcm63xx/patches-3.6/801-ssb_export_fallback_sprom.patch b/target/linux/brcm63xx/patches-3.6/801-ssb_export_fallback_sprom.patch deleted file mode 100644 index 9484b823aa..0000000000 --- a/target/linux/brcm63xx/patches-3.6/801-ssb_export_fallback_sprom.patch +++ /dev/null @@ -1,27 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -14,6 +14,7 @@ - #include <linux/ssb/ssb.h> - #include <linux/gpio_keys.h> - #include <linux/input.h> -+#include <linux/export.h> - #include <linux/spi/spi.h> - #include <linux/spi/spi_gpio.h> - #include <linux/spi/74x164.h> -@@ -3810,7 +3811,7 @@ static const struct board_info __initdat - * bcm4318 WLAN work - */ - #ifdef CONFIG_SSB_PCIHOST --static struct ssb_sprom bcm63xx_sprom = { -+struct ssb_sprom bcm63xx_sprom = { - .revision = 0x02, - .board_rev = 0x17, - .country_code = 0x0, -@@ -3830,6 +3831,7 @@ static struct ssb_sprom bcm63xx_sprom = - .boardflags_lo = 0x2848, - .boardflags_hi = 0x0000, - }; -+EXPORT_SYMBOL(bcm63xx_sprom); - - int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) - { diff --git a/target/linux/brcm63xx/patches-3.6/802-rtl8367r_fix_RGMII_support.patch b/target/linux/brcm63xx/patches-3.6/802-rtl8367r_fix_RGMII_support.patch deleted file mode 100644 index 9037d8954a..0000000000 --- a/target/linux/brcm63xx/patches-3.6/802-rtl8367r_fix_RGMII_support.patch +++ /dev/null @@ -1,30 +0,0 @@ -From e3208e6087642b95a5bab3101fc9c6e34892c861 Mon Sep 17 00:00:00 2001 -From: Miguel GAIO <miguel.gaio@efixo.com> -Date: Fri, 6 Jul 2012 14:12:33 +0200 -Subject: [PATCH 6/8] * [rtl8367r] Fix RGMII support - ---- - drivers/net/phy/rtl8367.c | 5 +++++ - 1 files changed, 5 insertions(+), 0 deletions(-) - ---- a/drivers/net/phy/rtl8367.c -+++ b/drivers/net/phy/rtl8367.c -@@ -146,6 +146,10 @@ - #define RTL8367_EXT_RGMXF_TXDELAY_MASK 1 - #define RTL8367_EXT_RGMXF_RXDELAY_MASK 0x7 - -+#define RTL8367_PHY_AD_REG 0x130f -+#define RTL8370_PHY_AD_DUMMY_1_OFFSET 5 -+#define RTL8370_PHY_AD_DUMMY_1_MASK 0xe0 -+ - #define RTL8367_DI_FORCE_REG(_x) (0x1310 + (_x)) - #define RTL8367_DI_FORCE_MODE BIT(12) - #define RTL8367_DI_FORCE_NWAY BIT(7) -@@ -894,6 +898,7 @@ static int rtl8367_extif_set_mode(struct - case RTL8367_EXTIF_MODE_RGMII_33V: - REG_WR(smi, RTL8367_CHIP_DEBUG0_REG, 0x0367); - REG_WR(smi, RTL8367_CHIP_DEBUG1_REG, 0x7777); -+ REG_RMW(smi, RTL8367_PHY_AD_REG, BIT(5), 0); - break; - - case RTL8367_EXTIF_MODE_TMII_MAC: |