1 files changed, 0 insertions, 100 deletions
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/serial.c b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/serial.c
deleted file mode 100644
index 9d22f6f9e1..0000000000
--- a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/serial.c
+++ /dev/null
@@ -1,100 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * 8250 serial console setup for the Realtek RTL838X SoC
- *
- * based on the original BSP by
- * Copyright (C) 2006-2012 Tony Wu (tonywu@realtek.com)
- *
- * Copyright (C) 2020 B. Koblitz
- *
- */
-
-#include <linux/types.h>
-#include <linux/ctype.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/version.h>
-#include <linux/serial.h>
-#include <linux/serial_core.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_reg.h>
-#include <linux/tty.h>
-#include <linux/clk.h>
-
-#include <asm/mach-rtl838x/mach-rtl838x.h>
-
-extern char arcs_cmdline[];
-
-int __init rtl838x_serial_init(void)
-{
-#ifdef CONFIG_SERIAL_8250
-	int ret;
-	struct uart_port p;
-	unsigned long baud = 0;
-	int err;
-	char parity = '\0', bits = '\0', flow = '\0';
-	char *s;
-	struct device_node *dn;
-
-	dn = of_find_compatible_node(NULL, NULL, "ns16550a");
-	if (dn) {
-		pr_info("Found NS16550a: %s (%s)\n", dn->name, dn->full_name);
-		dn = of_find_compatible_node(dn, NULL, "ns16550a");
-		if (dn && of_device_is_available(dn) && soc_info.family == RTL8380_FAMILY_ID) {
-			/* Enable UART1 on RTL838x */
-			pr_info("Enabling uart1\n");
-			sw_w32(0x10, RTL838X_GMII_INTF_SEL);
-		}
-	} else {
-		pr_err("No NS16550a UART found!");
-		return -ENODEV;
-	}
-
-	s = strstr(arcs_cmdline, "console=ttyS0,");
-	if (s) {
-		s += 14;
-		err = kstrtoul(s, 10, &baud);
-		if (err)
-			baud = 0;
-		while (isdigit(*s))
-			s++;
-		if (*s == ',')
-			s++;
-		if (*s)
-			parity = *s++;
-		if (*s == ',')
-			s++;
-		if (*s)
-			bits = *s++;
-		if (*s == ',')
-			s++;
-		if (*s == 'h')
-			flow = 'r';
-	}
-
-	if (baud == 0) {
-		baud = 38400;
-		pr_warn("Using default baud rate: %lu\n", baud);
-	}
-	if (parity != 'n' && parity != 'o' && parity != 'e')
-		parity = 'n';
-	if (bits != '7' && bits != '8')
-		bits = '8';
-
-	memset(&p, 0, sizeof(p));
-
-	p.type = PORT_16550A;
-	p.membase = (unsigned char *) RTL838X_UART0_BASE;
-	p.irq = RTL838X_UART0_IRQ;
-	p.uartclk = SYSTEM_FREQ - (24 * baud);
-	p.flags = UPF_SKIP_TEST | UPF_LOW_LATENCY | UPF_FIXED_TYPE;
-	p.iotype = UPIO_MEM;
-	p.regshift = 2;
-	p.fifosize = 1;
-
-	/* Call early_serial_setup() here, to set up 8250 console driver */
-	if (early_serial_setup(&p) != 0)
-		ret = 1;
-#endif
-	return 0;
-}