diff options
Diffstat (limited to 'target/linux/realtek/dts-5.10/rtl8393_panasonic_m48eg-pn28480k.dts')
-rw-r--r-- | target/linux/realtek/dts-5.10/rtl8393_panasonic_m48eg-pn28480k.dts | 380 |
1 files changed, 0 insertions, 380 deletions
diff --git a/target/linux/realtek/dts-5.10/rtl8393_panasonic_m48eg-pn28480k.dts b/target/linux/realtek/dts-5.10/rtl8393_panasonic_m48eg-pn28480k.dts deleted file mode 100644 index 6a7eb6eb81..0000000000 --- a/target/linux/realtek/dts-5.10/rtl8393_panasonic_m48eg-pn28480k.dts +++ /dev/null @@ -1,380 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "rtl839x.dtsi" -#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi" - -#include <dt-bindings/interrupt-controller/irq.h> - -/ { - compatible = "panasonic,m48eg-pn28480k", "realtek,rtl8393-soc"; - model = "Panasonic Switch-M48eG PN28480K"; - - aliases { - led-boot = &led_status_eco_green; - led-failsafe = &led_status_eco_amber; - led-running = &led_status_eco_green; - led-upgrade = &led_status_eco_green; - }; - - fan: gpio-fan { - compatible = "gpio-fan"; - gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>; - /* the actual speeds (rpm) are unknown, just use dummy values */ - gpio-fan,speed-map = <1 0>, <2 1>; - #cooling-cells = <2>; - }; - - /* - * sfp0/1/2/3 are "combo" port with each TP port (45/46/47/48), - * and they are connected to the RTL8218FB. Currently, there is - * no support for the chip and only TP ports work by the RTL8218B - * support. - */ - sfp0: sfp-p45 { - compatible = "sff,sfp"; - i2c-bus = <&i2c0>; - tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; - tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; - los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; - }; - - sfp1: sfp-p46 { - compatible = "sff,sfp"; - i2c-bus = <&i2c1>; - tx-fault-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; - tx-disable-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 6 GPIO_ACTIVE_LOW>; - los-gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; - }; - - sfp2: sfp-p47 { - compatible = "sff,sfp"; - i2c-bus = <&i2c2>; - tx-fault-gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; - tx-disable-gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 10 GPIO_ACTIVE_LOW>; - los-gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>; - }; - - sfp3: sfp-p48 { - compatible = "sff,sfp"; - i2c-bus = <&i2c3>; - tx-fault-gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; - tx-disable-gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 14 GPIO_ACTIVE_LOW>; - los-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; - }; - - thermal-zones { - /* - * Zone for SoC temperature - * - * Fan speed: - * - * - 0-44 celsius: Low - * - 45-54 celsius: High - */ - cpu-thermal { - polling-delay-passive = <1000>; - polling-delay = <2000>; - - thermal-sensors = <&tsens_soc>; - - trips { - cpu_alert: trip-point { - temperature = <45000>; - hysteresis = <4000>; - type = "active"; - }; - - cpu_crit { - temperature = <55000>; - hysteresis = <1000>; - type = "critical"; - }; - }; - - cooling-maps { - map { - trip = <&cpu_alert>; - cooling-device = <&fan 0 1>; - }; - }; - }; - - /* - * Zone for system temperature - * - * Fan speed: - * - * - 0-39 celsius: Low - * - 40-49 celsius: High - * - * Note: official recommended ranges of temperature on each - * fan speed setting: - * - * - Low speed : 0-40 celsius - * - High speed: 0-50 celsius - * - * (stock firmware doesn't support auto-selection of - * speed and need to be selected manually by user) - */ - sys-thermal { - polling-delay-passive = <1000>; - polling-delay = <2000>; - - thermal-sensors = <&tsens_sys>; - - trips { - sys_alert: trip-point { - temperature = <40000>; - hysteresis = <4000>; - type = "active"; - }; - - sys_crit { - temperature = <50000>; - hysteresis = <2000>; - type = "critical"; - }; - }; - - cooling-maps { - map { - trip = <&sys_alert>; - cooling-device = <&fan 0 1>; - }; - }; - }; - }; -}; - -&leds { - led_status_eco_amber: led-5 { - label = "amber:status_eco"; - gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; - color = <LED_COLOR_ID_AMBER>; - function = LED_FUNCTION_STATUS; - function-enumerator = <1>; - }; - - led_status_eco_green: led-6 { - label = "green:status_eco"; - gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; - color = <LED_COLOR_ID_GREEN>; - function = LED_FUNCTION_STATUS; - function-enumerator = <2>; - }; -}; - -&i2c_gpio_0 { - scl-gpios = <&gpio0 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - sda-gpios = <&gpio0 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - - /* Microchip TCN75A (for SoC) */ - tsens_soc: sensor@48 { - compatible = "microchip,tcn75"; - reg = <0x48>; - #thermal-sensor-cells = <0>; - }; - - /* Microchip TCN75A (for System) */ - tsens_sys: sensor@49 { - compatible = "microchip,tcn75"; - reg = <0x49>; - #thermal-sensor-cells = <0>; - }; -}; - -&i2c_gpio_1 { - scl-gpios = <&gpio0 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - sda-gpios = <&gpio0 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; -}; - -&gpio2 { - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&gpio0>; - interrupts = <18 IRQ_TYPE_EDGE_FALLING>; - - /* - * GPIO12 (IO1_4): 5x RTL8218B + RTL8218FB - * - * This GPIO pin should be specified as "reset-gpio" in mdio node, - * but the current configuration of RTL8218B phy in the phy driver - * seems to be incomplete and RTL8218FB phy won't be configured on - * RTL8218D support. So, ethernet ports on these phys will be broken - * after hard-resetting. - * (RTL8218FB phy will be detected as RTL8218D by the phy driver) - * At the moment, configure this GPIO pin as gpio-hog to avoid breaking - * by resetting. - */ - ext_switch_reset { - gpio-hog; - gpios = <12 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "ext-switch-reset"; - }; -}; - -&i2c_switch { - i2c0: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - - i2c1: i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - }; - - i2c2: i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <2>; - }; - - i2c3: i2c@3 { - #address-cells = <1>; - #size-cells = <0>; - reg = <3>; - }; -}; - -ðernet0 { - mdio-bus { - compatible = "realtek,rtl838x-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - EXTERNAL_PHY(0) - EXTERNAL_PHY(1) - EXTERNAL_PHY(2) - EXTERNAL_PHY(3) - EXTERNAL_PHY(4) - EXTERNAL_PHY(5) - EXTERNAL_PHY(6) - EXTERNAL_PHY(7) - - EXTERNAL_PHY(8) - EXTERNAL_PHY(9) - EXTERNAL_PHY(10) - EXTERNAL_PHY(11) - EXTERNAL_PHY(12) - EXTERNAL_PHY(13) - EXTERNAL_PHY(14) - EXTERNAL_PHY(15) - - EXTERNAL_PHY(16) - EXTERNAL_PHY(17) - EXTERNAL_PHY(18) - EXTERNAL_PHY(19) - EXTERNAL_PHY(20) - EXTERNAL_PHY(21) - EXTERNAL_PHY(22) - EXTERNAL_PHY(23) - - EXTERNAL_PHY(24) - EXTERNAL_PHY(25) - EXTERNAL_PHY(26) - EXTERNAL_PHY(27) - EXTERNAL_PHY(28) - EXTERNAL_PHY(29) - EXTERNAL_PHY(30) - EXTERNAL_PHY(31) - - EXTERNAL_PHY(32) - EXTERNAL_PHY(33) - EXTERNAL_PHY(34) - EXTERNAL_PHY(35) - EXTERNAL_PHY(36) - EXTERNAL_PHY(37) - EXTERNAL_PHY(38) - EXTERNAL_PHY(39) - - /* RTL8218FB */ - EXTERNAL_PHY(40) - EXTERNAL_PHY(41) - EXTERNAL_PHY(42) - EXTERNAL_PHY(43) - EXTERNAL_PHY(44) - EXTERNAL_PHY(45) - EXTERNAL_PHY(46) - EXTERNAL_PHY(47) - }; -}; - -&switch0 { - ports { - #address-cells = <1>; - #size-cells = <0>; - - SWITCH_PORT(0, 1, qsgmii) - SWITCH_PORT(1, 2, qsgmii) - SWITCH_PORT(2, 3, qsgmii) - SWITCH_PORT(3, 4, qsgmii) - SWITCH_PORT(4, 5, qsgmii) - SWITCH_PORT(5, 6, qsgmii) - SWITCH_PORT(6, 7, qsgmii) - SWITCH_PORT(7, 8, qsgmii) - - SWITCH_PORT(8, 9, qsgmii) - SWITCH_PORT(9, 10, qsgmii) - SWITCH_PORT(10, 11, qsgmii) - SWITCH_PORT(11, 12, qsgmii) - SWITCH_PORT(12, 13, qsgmii) - SWITCH_PORT(13, 14, qsgmii) - SWITCH_PORT(14, 15, qsgmii) - SWITCH_PORT(15, 16, qsgmii) - - SWITCH_PORT(16, 17, qsgmii) - SWITCH_PORT(17, 18, qsgmii) - SWITCH_PORT(18, 19, qsgmii) - SWITCH_PORT(19, 20, qsgmii) - SWITCH_PORT(20, 21, qsgmii) - SWITCH_PORT(21, 22, qsgmii) - SWITCH_PORT(22, 23, qsgmii) - SWITCH_PORT(23, 24, qsgmii) - - SWITCH_PORT(24, 25, qsgmii) - SWITCH_PORT(25, 26, qsgmii) - SWITCH_PORT(26, 27, qsgmii) - SWITCH_PORT(27, 28, qsgmii) - SWITCH_PORT(28, 29, qsgmii) - SWITCH_PORT(29, 30, qsgmii) - SWITCH_PORT(30, 31, qsgmii) - SWITCH_PORT(31, 32, qsgmii) - - SWITCH_PORT(32, 33, qsgmii) - SWITCH_PORT(33, 34, qsgmii) - SWITCH_PORT(34, 35, qsgmii) - SWITCH_PORT(35, 36, qsgmii) - SWITCH_PORT(36, 37, qsgmii) - SWITCH_PORT(37, 38, qsgmii) - SWITCH_PORT(38, 39, qsgmii) - SWITCH_PORT(39, 40, qsgmii) - - SWITCH_PORT(40, 41, qsgmii) - SWITCH_PORT(41, 42, qsgmii) - SWITCH_PORT(42, 43, qsgmii) - SWITCH_PORT(43, 44, qsgmii) - SWITCH_PORT(44, 45, qsgmii) - SWITCH_PORT(45, 46, qsgmii) - SWITCH_PORT(46, 47, qsgmii) - SWITCH_PORT(47, 48, qsgmii) - - port@52 { - ethernet = <ðernet0>; - reg = <52>; - phy-mode = "internal"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; |