diff options
Diffstat (limited to 'target/linux/ramips')
11 files changed, 212 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom index 9a714ddc69..ac97d037c1 100644 --- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom +++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom @@ -68,6 +68,10 @@ case "$FIRMWARE" in rt2x00_eeprom_extract "factory" 0 272 ;; + wl341v3) + rt2x00_eeprom_extract "board-nvram" 64880 272 + ;; + *) rt2x00_eeprom_die "board $board is not supported yet" ;; diff --git a/target/linux/ramips/base-files/etc/uci-defaults/network b/target/linux/ramips/base-files/etc/uci-defaults/network index cc5600bcfd..bce24e8432 100755 --- a/target/linux/ramips/base-files/etc/uci-defaults/network +++ b/target/linux/ramips/base-files/etc/uci-defaults/network @@ -111,6 +111,11 @@ ramips_setup_macs() wan_mac=$(ramips_get_mac_binary factory 40) ;; + wl341v3) + lan_mac=$(ramips_get_mac_binary board-nvram 65440) + wan_mac=$(/usr/sbin/maccalc add "$lan_mac" 1) + ;; + wli-tx4-ag300n) lan_mac=$(ramips_get_mac_binary factory 4) ;; diff --git a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac index 9a4d515b19..f6884c8477 100644 --- a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac +++ b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac @@ -29,6 +29,10 @@ preinit_set_mac_address() { mac=$(ramips_get_mac_binary factory 40) ifconfig eth0 hw ether $mac 2>/dev/null ;; + wl341v3) + mac=$(ramips_get_mac_binary board-nvram 65440) + ifconfig eth0 hw ether $mac 2>/dev/null + ;; esac } diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index ca9b3c9cfc..b3c54e82db 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -113,6 +113,9 @@ ramips_board_name() { *"WHR-G300N") name="whr-g300n" ;; + *"Sitecom WL-341 v3") + name="wl341v3" + ;; *"Sitecom WL-351 v1 002") name="wl-351" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 30754b5c2f..494e774ef9 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -30,6 +30,7 @@ platform_check_image() { rt-n15 | \ w502u |\ v22rw-2x2 | \ + wl341v3 | \ wli-tx4-ag300n | \ whr-g300n |\ wr512-3gn) diff --git a/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h b/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h index 272e2b818e..bec6ff0bec 100644 --- a/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h +++ b/target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h @@ -42,6 +42,7 @@ enum ramips_mach_type { RAMIPS_MACH_W502U, /* ALFA Networks W502U */ RAMIPS_MACH_WCR150GN, /* Sparklan WCR-150GN */ RAMIPS_MACH_WHR_G300N, /* Buffalo WHR-G300N */ + RAMIPS_MACH_WL341V3, /* Sitecom WL-341 v3 */ RAMIPS_MACH_WL351, /* Sitecom WL-351 v1 002 */ RAMIPS_MACH_WR512_3GN, /* SH-WR512NU/WS-WR512N1-like 3GN*/ }; diff --git a/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig b/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig index 45d6cd307a..826a484fe9 100644 --- a/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig +++ b/target/linux/ramips/files/arch/mips/ralink/rt305x/Kconfig @@ -86,6 +86,11 @@ config RT305X_MACH_V22RW_2X2 select RALINK_DEV_GPIO_BUTTONS select RALINK_DEV_GPIO_LEDS +config RT305X_MACH_WL341V3 + bool "Sitecom WL-341 v3 board support" + select RALINK_DEV_GPIO_BUTTONS + select RALINK_DEV_GPIO_LEDS + config RT305X_MACH_WL351 bool "Sitecom WL-351 support" select RALINK_DEV_GPIO_BUTTONS diff --git a/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile b/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile index 5a45412e5c..743493e80b 100644 --- a/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile +++ b/target/linux/ramips/files/arch/mips/ralink/rt305x/Makefile @@ -30,4 +30,5 @@ obj-$(CONFIG_RT305X_MACH_W502U) += mach-w502u.o obj-$(CONFIG_RT305X_MACH_WCR150GN) += mach-wcr150gn.o obj-$(CONFIG_RT305X_MACH_WHR_G300N) += mach-whr-g300n.o obj-$(CONFIG_RT305X_MACH_WR512_3GN) += mach-wr512-3gn.o +obj-$(CONFIG_RT305X_MACH_WL341V3) += mach-wl341v3.o obj-$(CONFIG_RT305X_MACH_WL351) += mach-wl351.o diff --git a/target/linux/ramips/files/arch/mips/ralink/rt305x/mach-wl341v3.c b/target/linux/ramips/files/arch/mips/ralink/rt305x/mach-wl341v3.c new file mode 100644 index 0000000000..9341be3bee --- /dev/null +++ b/target/linux/ramips/files/arch/mips/ralink/rt305x/mach-wl341v3.c @@ -0,0 +1,154 @@ +/* + * Sitecom WL341v3 board support + * + * Copyright (C) 2012 Marco Antonio Mauro <marcus90@gmail.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> + +#include <asm/mach-ralink/machine.h> +#include <asm/mach-ralink/dev-gpio-buttons.h> +#include <asm/mach-ralink/dev-gpio-leds.h> +#include <asm/mach-ralink/rt305x.h> +#include <asm/mach-ralink/rt305x_regs.h> + +#include "devices.h" + +#define WL341V3_GPIO_LED_FIRST_AMBER 9 +#define WL341V3_GPIO_LED_FIRST_BLUE 13 +#define WL341V3_GPIO_LED_THIRD_AMBER 11 +#define WL341V3_GPIO_LED_THIRD_BLUE 14 +#define WL341V3_GPIO_LED_FOURTH_BLUE 10 +#define WL341V3_GPIO_LED_FIFTH_AMBER 12 +#define WL341V3_GPIO_LED_FIFTH_BLUE 8 + +#define WL341V3_GPIO_BUTTON_WPS 5 /* active low */ +#define WL341V3_GPIO_BUTTON_RESET 7 /* active low */ + +#define WL341V3_BUTTONS_POLL_INTERVAL 20 + +#ifdef CONFIG_MTD_PARTITIONS +static struct mtd_partition wl341v3_partitions[] = { + { + .name = "u-boot", + .offset = 0, + .size = 0x020000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "board-nvram", + .offset = 0x020000, + .size = 0x010000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "u-boot-env", + .offset = 0x030000, + .size = 0x010000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "kernel", + .offset = 0x040000, + .size = 0x0d0000, + }, { + .name = "rootfs", + .offset = 0x110000, + .size = 0x2e0000, + }, { + .name = "signature-eRcOmM", + .offset = 0x3f0000, + .size = 0x010000, + }, { + .name = "firmware", + .offset = 0x040000, + .size = 0x3b0000, + }, { + .name = "fullflash", + .offset = 0x000000, + .size = 0x400000, + } +}; +#endif /* CONFIG_MTD_PARTITIONS */ + +static struct physmap_flash_data wl341v3_flash_data = { +#ifdef CONFIG_MTD_PARTITIONS + .nr_parts = ARRAY_SIZE(wl341v3_partitions), + .parts = wl341v3_partitions, +#endif +}; + +static struct gpio_led wl341v3_leds_gpio[] __initdata = { + { + .name = "wl341v3:amber:first", + .gpio = WL341V3_GPIO_LED_FIRST_AMBER, + .active_low = 1, + }, { + .name = "wl341v3:blue:first", + .gpio = WL341V3_GPIO_LED_FIRST_BLUE, + .active_low = 1, + }, { + .name = "wl341v3:amber:third", + .gpio = WL341V3_GPIO_LED_THIRD_AMBER, + .active_low = 1, + }, { + .name = "wl341v3:blue:third", + .gpio = WL341V3_GPIO_LED_THIRD_BLUE, + .active_low = 1, + }, { + .name = "wl341v3:blue:fourth", + .gpio = WL341V3_GPIO_LED_FOURTH_BLUE, + .active_low = 1, + }, { + .name = "wl341v3:amber:fifth", + .gpio = WL341V3_GPIO_LED_FIFTH_AMBER, + .active_low = 1, + }, { + .name = "wl341v3:blue:fifth", + .gpio = WL341V3_GPIO_LED_FIFTH_BLUE, + .active_low = 1, + } +}; + +static struct gpio_button wl341v3_gpio_buttons[] __initdata = { + { + .desc = "reset", + .type = EV_KEY, + .code = KEY_RESTART, + .threshold = 3, + .gpio = WL341V3_GPIO_BUTTON_RESET, + .active_low = 1, + }, { + .desc = "wps", + .type = EV_KEY, + .code = KEY_WPS_BUTTON, + .threshold = 3, + .gpio = WL341V3_GPIO_BUTTON_WPS, + .active_low = 1, + } +}; + +static void __init wl341v3_init(void) +{ + rt305x_gpio_init(RT305X_GPIO_MODE_GPIO << RT305X_GPIO_MODE_UART0_SHIFT); + + rt305x_register_flash(0, &wl341v3_flash_data); + rt305x_esw_data.vlan_config = RT305X_ESW_VLAN_CONFIG_WLLLL; + rt305x_register_ethernet(); + ramips_register_gpio_leds(-1, ARRAY_SIZE(wl341v3_leds_gpio), + wl341v3_leds_gpio); + ramips_register_gpio_buttons(-1, WL341V3_BUTTONS_POLL_INTERVAL, + ARRAY_SIZE(wl341v3_gpio_buttons), + wl341v3_gpio_buttons); + rt305x_register_wifi(); + rt305x_register_wdt(); + rt305x_register_usb(); +} + +MIPS_MACHINE(RAMIPS_MACH_WL341V3, "WL341V3", "Sitecom WL-341 v3", + wl341v3_init); diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile index c6b214ff36..745edefbae 100644 --- a/target/linux/ramips/image/Makefile +++ b/target/linux/ramips/image/Makefile @@ -67,6 +67,28 @@ define BuildFirmware/Generic fi; fi endef +define BuildFirmware/WL341V3 + $(call PatchKernelLzma,$(2),$(3) $($(4))) + $(call MkImage,lzma,"$(KDIR)/vmlinux-$(2).bin.lzma","$(KDIR)/vmlinux-$(2).uImage") + if [ `stat -c%s "$(KDIR)/vmlinux-$(2).uImage"` -gt $(5) ]; then \ + echo "Warning: $(KDIR)/vmlinux-$(2).uImage is too big"; \ + else if [ `stat -c%s $(KDIR)/root.$(1)` -gt $(6) ]; then \ + echo "Warning: $(KDIR)/root.$(1) is too big"; \ + else \ + ( \ + dd if=/dev/zero bs=195936 count=1; \ + echo "1.01"; \ + dd if=/dev/zero bs=581 count=1; \ + echo -n -e "\x73\x45\x72\x43\x6F\x4D\x6D\x00\x01\x00\x00\x59\x4E\x37\x95\x58\x10\x00\x20\x00\x28\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x11\x03\x00\x00\x80\x00\x00\x00\x00\x03\x00\x00\x10\x12\x00\x00\x00\x10\x73\x45\x72\x43\x6F\x4D\x6D"; \ + dd if=/dev/zero bs=65552 count=1; \ + dd if=$(KDIR)/vmlinux-$(2).uImage bs=$(5) conv=sync; \ + dd if=$(KDIR)/root.$(1) bs=64k conv=sync; \ + dd if=/dev/zero bs=`expr 4194304 - 262144 - 16 - $(5) - \( \( \( \`stat -c%s $(KDIR)/root.$(1)\` / 65536 \) + 1 \) \* 65536 \)` count=1; \ + echo -n -e "\x11\x03\x80\x00\x10\x12\x90\xF7\x65\x52\x63\x4F\x6D\x4D\x00\x00"; \ + ) > $(call imgname,$(1),$(2))-factory.bin; \ + fi; fi +endef + define BuildFirmware/Buffalo $(call PatchKernelLzma,$(2),board=$(3) $($(4))) $(call MkImage,lzma,"$(KDIR)/vmlinux-$(2).bin.lzma","$(KDIR)/vmlinux-$(2).uImage") @@ -151,6 +173,16 @@ define Image/Build/Template/OMNIEMB $(call BuildFirmware/Generic,$(1),$(2),board=$(3) console=$(console_OMNIEMB),mtdlayout_OMNIEMB,1048576,7012352) endef +mtdlayout_sercomm_4M=mtdparts=physmap-flash.0:128k(u-boot)ro,64k(board-nvram)ro,64k(u-boot-env)ro,832k(kernel),2944k(rootfs),64k(signature-eRcOmM),3776k@0x40000(firmware),4096k@0x0(fullflash) +define Image/Build/Template/WL341V3 + $(call BuildFirmware/Generic,$(1),$(2),board=$(3),mtdlayout_sercomm_4M,851968,3014656) + $(call BuildFirmware/WL341V3,$(1),$(2),board=$(3),mtdlayout_sercomm_4M,851968,3014656) +endef + +define Image/Build/Profile/WL341V3 + $(call Image/Build/Template/WL341V3,$(1),wl341v3,WL341V3) +endef + define Image/Build/Profile/DIR300B1 $(call Image/Build/Template/DIR300B1,$(1),dir-300-b1,DIR-300-B1,wrgn23_dlwbr_dir300b) $(call Image/Build/Template/DIR300B1,$(1),dir-600-b1,DIR-600-B1,wrgn23_dlwbr_dir600b) @@ -294,6 +326,7 @@ define Image/Build/Profile/Default $(call Image/Build/Profile/MOFI35003GN,$(1)) $(call Image/Build/Profile/W502U,$(1)) $(call Image/Build/Profile/WR5123GN,$(1)) + $(call Image/Build/Profile/WL341V3,$(1)) $(call Image/Build/Profile/WL351,$(1)) endef endif diff --git a/target/linux/ramips/rt305x/config-2.6.39 b/target/linux/ramips/rt305x/config-2.6.39 index 891a421d2d..e9ef379c07 100644 --- a/target/linux/ramips/rt305x/config-2.6.39 +++ b/target/linux/ramips/rt305x/config-2.6.39 @@ -109,6 +109,7 @@ CONFIG_RT305X_MACH_V22RW_2X2=y CONFIG_RT305X_MACH_W502U=y CONFIG_RT305X_MACH_WCR150GN=y CONFIG_RT305X_MACH_WHR_G300N=y +CONFIG_RT305X_MACH_WL341V3=y CONFIG_RT305X_MACH_WL351=y CONFIG_RT305X_MACH_WR512_3GN=y # CONFIG_SCSI_DMA is not set |