1 files changed, 0 insertions, 83 deletions
diff --git a/target/linux/layerscape/patches-5.4/701-net-0327-at803x-Address-packet-drops-at-low-traffic-rate-due-.patch b/target/linux/layerscape/patches-5.4/701-net-0327-at803x-Address-packet-drops-at-low-traffic-rate-due-.patch
deleted file mode 100644
index babecdecb7..0000000000
--- a/target/linux/layerscape/patches-5.4/701-net-0327-at803x-Address-packet-drops-at-low-traffic-rate-due-.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From 53c3bd0d5a873c23841bb95e7b95c1c3630c50bd Mon Sep 17 00:00:00 2001
-From: Vladimir Oltean <vladimir.oltean@nxp.com>
-Date: Thu, 12 Jul 2018 13:03:13 +0300
-Subject: [PATCH] at803x: Address packet drops at low traffic rate due to
- SmartEEE feature
-
-* According to the AR8035 datasheet, smartEEE mode (active by default)
-  makes the PHY enters sleep after a configurable idle time. It does
-  this autonomously, without LPI (Low Power Idle) signals coming from MAC.
-* Tested with ping (default of 1 second interval) over back-to-back
-  RGMII between 2 boards having AR8035 at both ends:
-    - Without patch:
-  225 packets transmitted, 145 received, 35% packet loss, time 229334ms
-    - With patch:
-  144 packets transmitted, 144 received, 0% packet loss, time 146378ms
-
-Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
----
- drivers/net/phy/Kconfig  | 10 ++++++++++
- drivers/net/phy/at803x.c | 22 ++++++++++++++++++++++
- 2 files changed, 32 insertions(+)
-
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -363,6 +363,16 @@ config AT803X_PHY
- 	---help---
- 	  Currently supports the AT8030 and AT8035 model
- 
-+config AT803X_PHY_SMART_EEE
-+	depends on AT803X_PHY
-+	default n
-+	tristate "SmartEEE feature for AT803X PHYs"
-+	---help---
-+	  Enables the Atheros SmartEEE feature (not IEEE 802.3az). When 2 PHYs
-+	  which support this feature are connected back-to-back, they may
-+	  negotiate a low-power sleep mode autonomously, without the Ethernet
-+	  controller's knowledge.  May cause packet loss.
-+
- config BCM63XX_PHY
- 	tristate "Broadcom 63xx SOCs internal PHY"
- 	depends on BCM63XX || COMPILE_TEST
---- a/drivers/net/phy/at803x.c
-+++ b/drivers/net/phy/at803x.c
-@@ -62,6 +62,8 @@
- #define AT803X_DEBUG_REG_5			0x05
- #define AT803X_DEBUG_TX_CLK_DLY_EN		BIT(8)
- 
-+#define AT803X_LPI_EN				BIT(8)
-+
- #define ATH8030_PHY_ID 0x004dd076
- #define ATH8031_PHY_ID 0x004dd074
- #define ATH8032_PHY_ID 0x004dd023
-@@ -299,10 +301,30 @@ static int at803x_probe(struct phy_devic
- 	return ret;
- }
- 
-+static void at803x_enable_smart_eee(struct phy_device *phydev, int on)
-+{
-+	int value;
-+
-+	/* 5.1.11 Smart_eee control3 */
-+	value = phy_read_mmd(phydev, MDIO_MMD_PCS, 0x805D);
-+	if (on)
-+		value |= AT803X_LPI_EN;
-+	else
-+		value &= ~AT803X_LPI_EN;
-+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x805D, value);
-+}
-+
- static int at803x_config_init(struct phy_device *phydev)
- {
- 	int ret;
- 
-+
-+#ifdef CONFIG_AT803X_PHY_SMART_EEE
-+	at803x_enable_smart_eee(phydev, 1);
-+#else
-+	at803x_enable_smart_eee(phydev, 0);
-+#endif
-+
- 	/* The RX and TX delay default is:
- 	 *   after HW reset: RX delay enabled and TX delay disabled
- 	 *   after SW reset: RX delay enabled, while TX delay retains the