diff options
Diffstat (limited to 'target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_tplink_vr200.dtsi')
-rw-r--r-- | target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_tplink_vr200.dtsi | 213 |
1 files changed, 0 insertions, 213 deletions
diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_tplink_vr200.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_tplink_vr200.dtsi deleted file mode 100644 index 77b4f0defb..0000000000 --- a/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_tplink_vr200.dtsi +++ /dev/null @@ -1,213 +0,0 @@ -#include "vr9.dtsi" - -#include <dt-bindings/input/input.h> -#include <dt-bindings/mips/lantiq_rcu_gphy.h> - -/ { - memory@0 { - device_type = "memory"; - reg = <0x0 0x7f00000>; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - pinctrl-0 = <&mdio_pins>, <&gphy0_led1_pins>, <&gphy1_led1_pins>; - pinctrl-names = "default"; - - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mtd-mac-address = <&romfile 0xf100>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - // gpios = <&gpio 42 GPIO_ACTIVE_LOW>; - }; - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "rgmii"; - phy-handle = <&phy5>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy5: ethernet-phy@5 { - reg = <0x5>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = <GPHY_MODE_GE>; -}; - -&gphy1 { - lantiq,gphy-mode = <GPHY_MODE_GE>; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - phy-rst { - lantiq,pins = "io42"; - lantiq,pull = <0>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - pcie-rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; -}; - -&pcie0 { - pcie@0 { - reg = <0 0 0 0 0>; - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - - wifi@0,0 { - reg = <0 0 0 0 0>; - mediatek,mtd-eeprom = <&radio 0x0000>; - big-endian; - ieee80211-freq-limit = <5000000 6000000>; - mtd-mac-address = <&romfile 0xf100>; - mtd-mac-address-increment = <2>; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -&spi { - status = "okay"; - - flash@4 { - compatible = "jedec,spi-nor"; - reg = <4>; - spi-max-frequency = <33250000>; - m25p,fast-read; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - reg = <0x0 0x20000>; - label = "u-boot"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0xf90000>; - label = "firmware"; - }; - - partition@fb0000 { - reg = <0xfb0000 0x10000>; - label = "radioDECT"; - read-only; - }; - - partition@fc0000 { - reg = <0xfc0000 0x10000>; - label = "config"; - read-only; - }; - - romfile: partition@fd0000 { - reg = <0xfd0000 0x10000>; - label = "romfile"; - read-only; - }; - - partition@fe0000 { - reg = <0xfe0000 0x10000>; - label = "rom"; - read-only; - }; - - radio: partition@ff0000 { - reg = <0xff0000 0x10000>; - label = "radio"; - read-only; - }; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; |