1 files changed, 0 insertions, 144 deletions
diff --git a/target/linux/kirkwood/patches-4.14/105-ea4500.patch b/target/linux/kirkwood/patches-4.14/105-ea4500.patch
deleted file mode 100644
index cfa499c911..0000000000
--- a/target/linux/kirkwood/patches-4.14/105-ea4500.patch
+++ /dev/null
@@ -1,144 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-@@ -26,6 +26,10 @@
- 	};
- 
- 	aliases {
-+		led-boot = &led_white_health;
-+		led-failsafe = &led_white_health;
-+		led-running = &led_white_health;
-+		led-upgrade = &led_white_health;
- 		serial0 = &uart0;
- 	};
- 
-@@ -58,9 +62,10 @@
- 		pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
- 		pinctrl-names = "default";
- 
--		white-health {
-+		led_white_health: white-health {
- 			label = "viper:white:health";
- 			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+			default-state = "on";
- 		};
- 
- 		white-pulse {
-@@ -69,9 +74,18 @@
- 		};
- 	};
- 
--	dsa {
--		status = "disabled";
-+	mvsw61xx {
-+		compatible = "marvell,88e6171";
-+		status = "okay";
-+		reg = <0x10>;
-+
-+		mii-bus = <&mdio>;
-+		cpu-port-0 = <5>;
-+		cpu-port-1 = <6>;
-+		is-indirect;
-+	};
- 
-+	dsa {
- 		compatible = "marvell,dsa";
- 		#address-cells = <2>;
- 		#size-cells = <0>;
-@@ -163,22 +177,22 @@
- 		};
- 
- 		partition@200000 {
--			label = "kernel";
-+			label = "kernel1";
- 			reg = <0x200000 0x2A0000>;
- 		};
- 
- 		partition@4A0000 {
--			label = "rootfs";
-+			label = "rootfs1";
- 			reg = <0x4A0000 0x1760000>;
- 		};
- 
- 		partition@1C00000 {
--			label = "alt_kernel";
-+			label = "kernel2";
- 			reg = <0x1C00000 0x2A0000>;
- 		};
- 
- 		partition@1EA0000 {
--			label = "alt_rootfs";
-+			label = "rootfs2";
- 			reg = <0x1EA0000 0x1760000>;
- 		};
- 
-@@ -209,53 +223,6 @@
- 
- &mdio {
- 	status = "okay";
--
--	switch@10 {
--		compatible = "marvell,mv88e6085";
--		#address-cells = <1>;
--		#size-cells = <0>;
--		reg = <16>;
--
--		ports {
--			#address-cells = <1>;
--			#size-cells = <0>;
--
--			port@0 {
--				reg = <0>;
--				label = "ethernet1";
--			};
--
--			port@1 {
--				reg = <1>;
--				label = "ethernet2";
--			};
--
--			port@2 {
--				reg = <2>;
--				label = "ethernet3";
--			};
--
--			port@3 {
--				reg = <3>;
--				label = "ethernet4";
--			};
--
--			port@4 {
--				reg = <4>;
--				label = "internet";
--			};
--
--			port@5 {
--				reg = <5>;
--				label = "cpu";
--				ethernet = <&eth0port>;
--				fixed-link {
--					speed = <1000>;
--					full-duplex;
--				};
--			};
--		};
--	};
- };
- 
- &uart0 {
-@@ -274,10 +241,14 @@
- };
- 
- /* eth1 is connected to the switch at port 6. However DSA only supports a
-- * single CPU port. So leave this port disabled to avoid confusion.
-+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
-  */
- &eth1 {
--	status = "disabled";
-+	status = "okay";
-+	ethernet1-port@0 {
-+		speed = <1000>;
-+		duplex = <1>;
-+	};
- };
- 
- /* There is no battery on the board, so the RTC does not keep