diff options
Diffstat (limited to 'target/linux/kirkwood/files-4.14/arch/arm')
4 files changed, 671 insertions, 0 deletions
diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts new file mode 100644 index 0000000000..af20cf9e2c --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts @@ -0,0 +1,124 @@ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "Seagate GoFlex Home"; + compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + aliases { + led-boot = &led_health; + led-failsafe = &led_fault; + led-running = &led_health; + led-upgrade = &led_fault; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; + stdout-path = &uart0; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pmx_usb_power_enable: pmx-usb-power-enable { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + pmx_led_white: pmx-led-white { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + pmx_led_green: pmx-led_green { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + pmx_led_orange: pmx-led-orange { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + }; + serial@12000 { + status = "ok"; + }; + + sata@80000 { + status = "okay"; + nr-ports = <2>; + }; + + }; + gpio-leds { + compatible = "gpio-leds"; + + led_health: health { + label = "status:green:health"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led_fault: fault { + label = "status:orange:fault"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + misc { + label = "status:white:misc"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "disk-activity"; + }; + }; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_power_enable>; + pinctrl-names = "default"; + + usb_power: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&nand { + chip-delay = <40>; + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "ubi"; + reg = <0x100000 0x0ff00000>; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts new file mode 100644 index 0000000000..004ce10219 --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts @@ -0,0 +1,250 @@ +/* + * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 + * + * (c) 2013 Jonas Gorski <jogo@openwrt.org> + * (c) 2013 Deutsche Telekom Innovation Laboratories + * (c) 2014 Luka Perkov <luka@openwrt.org> + * (c) 2014 Dan Walters <dan@walters.io> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" + +/ { + model = "Linksys Audi (EA3500)"; + compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; + pinctrl-names = "default"; + + wps { + label = "WPS Button"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = < &pmx_led_green_power >; + pinctrl-names = "default"; + + led_power: power { + label = "audi:green:power"; + gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + mvsw61xx { + compatible = "marvell,88e6171"; + status = "okay"; + reg = <0x10>; + + mii-bus = <&mdio>; + cpu-port-0 = <5>; + cpu-port-1 = <6>; + is-indirect; + }; + + dsa { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + dsa,ethernet = <ð0port>; + dsa,mii-bus = <&mdio>; + + switch@16,0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <16 0>; /* MDIO address 16, switch 0 in tree */ + + port@0 { + reg = <0>; + label = "ethernet1"; + }; + + port@1 { + reg = <1>; + label = "ethernet2"; + }; + + port@2 { + reg = <2>; + label = "ethernet3"; + }; + + port@3 { + reg = <3>; + label = "ethernet4"; + }; + + port@4 { + reg = <4>; + label = "internet"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + }; + }; +}; + +&pinctrl { + pmx_led_green_power: pmx-led-green-power { + marvell,pins = "mpp7"; + marvell,function = "gpo"; + }; + pmx_btn_wps: pmx-btn-wps { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + pmx_btn_reset: pmx-btn-reset { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; +}; + +&nand { + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "u_env"; + reg = <0x80000 0x4000>; + }; + + partition@84000 { + label = "s_env"; + reg = <0x84000 0x4000>; + }; + + partition@200000 { + label = "kernel1"; + reg = <0x200000 0x290000>; + }; + + partition@490000 { + label = "rootfs1"; + reg = <0x490000 0x1170000>; + }; + + partition@1600000 { + label = "kernel2"; + reg = <0x1600000 0x290000>; + }; + + partition@1890000 { + label = "rootfs2"; + reg = <0x1890000 0x1170000>; + }; + + partition@2a00000 { + label = "syscfg"; + reg = <0x2a00000 0x1600000>; + }; + + partition@88000 { + label = "unused"; + reg = <0x88000 0x178000>; + }; + + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&mdio { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set + * fixed speed and duplex. + */ +ð0 { + status = "okay"; + ethernet0-port@0 { + speed = <1000>; + duplex = <1>; + }; +}; + +/* eth1 is connected to the switch at port 6. However DSA only supports a + * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. + */ +ð1 { + status = "okay"; + ethernet1-port@0 { + speed = <1000>; + duplex = <1>; + }; +}; + +/* There is no battery on the board, so the RTC does not keep + * time when there is no power, making it useless. + */ +&rtc { + status = "disabled"; +}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts new file mode 100644 index 0000000000..a83a55af07 --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts @@ -0,0 +1,132 @@ +/dts-v1/; + +#include "kirkwood-nsa3x0-common.dtsi" + +/* + * There are at least two different NSA310 designs. This variant has + * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. + */ + +/ { + model = "ZyXEL NSA310b"; + compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + aliases { + led-boot = &led_green_sys; + led-failsafe = &led_red_sys; + led-running = &led_green_sys; + led-upgrade = &led_red_sys; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-names = "default"; + + pmx_led_esata_green: pmx-led-esata-green { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_led_esata_red: pmx-led-esata-red { + marvell,pins = "mpp13"; + marvell,function = "gpio"; + }; + + pmx_led_usb_green: pmx-led-usb-green { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_led_usb_red: pmx-led-usb-red { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_led_sys_green: pmx-led-sys-green { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_led_sys_red: pmx-led-sys-red { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_hdd_green: pmx-led-hdd-green { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_led_hdd_red: pmx-led-hdd-red { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + }; + + i2c@11000 { + status = "okay"; + + lm85: lm85@2e { + compatible = "national,lm85"; + reg = <0x2e>; + }; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_green_sys: green-sys { + label = "nsa310:green:sys"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + led_red_sys: red-sys { + label = "nsa310:red:sys"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + green-hdd { + label = "nsa310:green:hdd"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + red-hdd { + label = "nsa310:red:hdd"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + green-esata { + label = "nsa310:green:esata"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + red-esata { + label = "nsa310:red:esata"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + green-usb { + label = "nsa310:green:usb"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + red-usb { + label = "nsa310:red:usb"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + }; + green-copy { + label = "nsa310:green:copy"; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; + red-copy { + label = "nsa310:red:copy"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; + }; +}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts new file mode 100644 index 0000000000..9296c3fc71 --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts @@ -0,0 +1,165 @@ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" + +/ { + model = "Cisco Systems ON100"; + compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + aliases { + led-boot = &led_health_green; + led-failsafe = &led_health_red; + led-running = &led_health_green; + led-upgrade = &led_health_red; + serial0 = &uart0; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_btn_reset>; + pinctrl-names = "default"; + + button@1 { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; + pinctrl-names = "default"; + + led_health_green: health_green { + label = "on100:green:health"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led_health_red: health_red { + label = "on100:red:health"; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + + health2_green { + label = "on100:green:health2"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + + health2_red { + label = "on100:red:health2"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð0 { + status = "okay"; + + ethernet0-port@0 { + phy-handle = <ðphy0>; + phy-connection-type = "rgmii-id"; + }; +}; + +ð1 { + status = "okay"; + + ethernet1-port@0 { + phy-handle = <ðphy1>; + phy-connection-type = "rgmii-id"; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + /* Marvell 88E1121R */ + compatible = "ethernet-phy-id0141.0cb0", + "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + /* Marvell 88E1121R */ + compatible = "ethernet-phy-id0141.0cb0", + "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x000a0000>; + read-only; + }; + + partition@a0000 { + label = "u-boot environment"; + reg = <0x000a0000 0x00020000>; + read-only; + }; + + partition@c0000 { + label = "kernel"; + reg = <0x000c0000 0x00540000>; + }; + + partition@600000 { + label = "ubi"; + reg = <0x00600000 0x1fa00000>; + }; +}; + +&pinctrl { + pmx_led_health_r: pmx-led-health-r { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_led_health_g: pmx-led-health-g { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_led_health2_r: pmx-led-health2-r { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + pmx_led_health2_g: pmx-led-health2-g { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + + pmx_btn_reset: pmx-led-reset { + marvell,pins = "mpp31"; + marvell,function = "gpio"; + }; +}; + +&sdio { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; |