diff options
Diffstat (limited to 'target/linux/ipq806x')
8 files changed, 383 insertions, 1 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 17f1a28abc..12d9e7b1b7 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -20,6 +20,7 @@ c2600) ;; d7800 |\ r7500 |\ +r7500v2 |\ r7800) ucidef_set_led_usbdev "usb1" "USB 1" "${board}:white:usb1" "1-1" ucidef_set_led_usbdev "usb2" "USB 2" "${board}:white:usb3" "3-1" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 16cc13cfc0..b72045538a 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -17,6 +17,7 @@ ap148 |\ c2600 |\ d7800 |\ r7500 |\ +r7500v2 |\ r7800) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0" diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index a23dd80a00..c7977e6375 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -56,6 +56,7 @@ case "$FIRMWARE" in hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) ath10kcal_extract "art" 4096 12064 ;; + r7500v2 |\ r7800) ath10kcal_extract "art" 4096 12064 ;; @@ -71,6 +72,7 @@ case "$FIRMWARE" in hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) ath10kcal_extract "art" 20480 12064 ;; + r7500v2 |\ r7800) ath10kcal_extract "art" 20480 12064 ;; diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh index adac916f6b..0b11b721a7 100644 --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh @@ -29,6 +29,9 @@ ipq806x_board_detect() { *"R7500") name="r7500" ;; + *"R7500v2") + name="r7500v2" + ;; *"Linksys EA8500"*) name="ea8500" ;; diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index cfd7cd7ed6..7726abb91f 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -10,6 +10,7 @@ platform_check_image() { d7800 |\ ea8500 |\ r7500 |\ + r7500v2 |\ r7800) nand_do_platform_check $board $1 return $?; @@ -34,6 +35,7 @@ platform_pre_upgrade() { ap148 |\ d7800 |\ r7500 |\ + r7500v2 |\ r7800) nand_do_upgrade "$1" ;; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts new file mode 100644 index 0000000000..079f5e8bf5 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts @@ -0,0 +1,350 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Netgear Nighthawk X4 R7500v2"; + compatible = "netgear,r7500v2", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0xe000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; + + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + pullups { + pins = "gpio39"; + bias-pull-up; + }; + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + sata-phy@1b400000 { + status = "ok"; + }; + + sata@29000000 { + status = "ok"; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + }; + + pcie1: pci@1b700000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + }; + + nand@1ac00000 { + status = "ok"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + artbak: art@1340000 { + label = "artbak"; + reg = <0x1340000 0x0140000>; + read-only; + }; + + kernel@1480000 { + label = "kernel"; + reg = <0x1480000 0x0200000>; + }; + + ubi@1680000 { + label = "ubi"; + reg = <0x1680000 0x1E00000>; + }; + + netgear@3480000 { + label = "netgear"; + reg = <0x3480000 0x4480000>; + read-only; + }; + + reserve@7900000 { + label = "reserve"; + reg = <0x7900000 0x0700000>; + read-only; + }; + + firmware@1480000 { + label = "firmware"; + reg = <0x1480000 0x2000000>; + }; + + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 1>; + linux,code = <KEY_WLAN>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 1>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 1>; + linux,code = <KEY_WPS_BUTTON>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + usb1 { + label = "r7500v2:amber:usb1"; + gpios = <&qcom_pinmux 7 0>; + }; + + usb3 { + label = "r7500v2:amber:usb3"; + gpios = <&qcom_pinmux 8 0>; + }; + + status { + label = "r7500v2:amber:status"; + gpios = <&qcom_pinmux 9 0>; + }; + + internet { + label = "r7500v2:white:internet"; + gpios = <&qcom_pinmux 22 0>; + }; + + wan { + label = "r7500v2:white:wan"; + gpios = <&qcom_pinmux 23 0>; + }; + + wps { + label = "r7500v2:white:wps"; + gpios = <&qcom_pinmux 24 0>; + }; + + esata { + label = "r7500v2:white:esata"; + gpios = <&qcom_pinmux 26 0>; + }; + + power { + label = "r7500v2:white:power"; + gpios = <&qcom_pinmux 53 0>; + default-state = "on"; + }; + + rfkill { + label = "r7500v2:white:rfkill"; + gpios = <&qcom_pinmux 64 0>; + }; + + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index 5ce007292f..45159462cc 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -175,6 +175,19 @@ define Device/R7500 DEVICE_PACKAGES := ath10k-firmware-qca99x0 endef +define Device/R7500v2 + $(call Device/DniImage) + DEVICE_DTS := qcom-ipq8064-r7500v2 + KERNEL_SIZE := 2097152 + NETGEAR_BOARD_ID := R7500v2 + NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4 + BLOCKSIZE := 128KiB + PAGESIZE := 2048 + BOARD_NAME := r7500v2 + DEVICE_TITLE := Netgear Nighthawk X4 R7500v2 + DEVICE_PACKAGES := ath10k-firmware-qca99x0 +endef + define Device/R7800 $(call Device/DniImage) DEVICE_DTS := qcom-ipq8064-r7800 @@ -188,6 +201,6 @@ define Device/R7800 DEVICE_PACKAGES := ath10k-firmware-qca9984 endef -TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7800 +TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 $(eval $(call BuildImage)) diff --git a/target/linux/ipq806x/patches-4.4/801-ARM-dts-qcom-add-Netgear-X4-R7500v2-dts-to-Makefile.patch b/target/linux/ipq806x/patches-4.4/801-ARM-dts-qcom-add-Netgear-X4-R7500v2-dts-to-Makefile.patch new file mode 100644 index 0000000000..57e76d224f --- /dev/null +++ b/target/linux/ipq806x/patches-4.4/801-ARM-dts-qcom-add-Netgear-X4-R7500v2-dts-to-Makefile.patch @@ -0,0 +1,10 @@ +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -511,6 +511,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ + qcom-ipq8064-db149.dtb \ + qcom-ipq8064-ea8500.dtb \ + qcom-ipq8064-r7500.dtb \ ++ qcom-ipq8064-r7500v2.dtb \ + qcom-ipq8064-r7800.dtb \ + qcom-msm8660-surf.dtb \ + qcom-msm8960-cdp.dtb \ |