diff options
Diffstat (limited to 'target/linux/ipq806x')
6 files changed, 457 insertions, 3 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index c23f25540b..fed821663a 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -27,6 +27,9 @@ nec,wg2600hp) ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt" ucidef_set_led_switch "wan" "WAN" "green:active" "switch0" "0x2" ;; +nec,wg2600hp3) + ucidef_set_led_switch "wan" "WAN" "green:active" "switch0" "0x2" + ;; netgear,d7800 |\ netgear,r7500 |\ netgear,r7500v2 |\ diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index eecf81a8cd..10b2ec0148 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -46,6 +46,10 @@ linksys,ea8500) ucidef_set_interface_macaddr "lan" "$hw_mac_addr" ucidef_set_interface_macaddr "wan" "$hw_mac_addr" ;; +nec,wg2600hp3) + ucidef_add_switch "switch0" \ + "2:lan" "3:lan" "4:lan" "5:lan" "0@eth1" "1:wan" "6@eth0" + ;; netgear,r7800 |\ tplink,c2600) ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index a22af9b676..8788fc92f6 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -24,7 +24,8 @@ case "$FIRMWARE" in caldata_extract "art" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1) ;; - nec,wg2600hp) + nec,wg2600hp |\ + nec,wg2600hp3) caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(mtd_get_mac_binary PRODUCTDATA 0x12) ;; @@ -62,7 +63,8 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2) ;; - nec,wg2600hp) + nec,wg2600hp |\ + nec,wg2600hp3) caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(mtd_get_mac_binary PRODUCTDATA 0xc) ;; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts new file mode 100644 index 0000000000..d234b94a46 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts @@ -0,0 +1,430 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq8062.dtsi" +#include <dt-bindings/input/input.h> + +/delete-node/ &nand_pins; + +/ { + model = "NEC Platforms Aterm WG2600HP3"; + compatible = "nec,wg2600hp3", "qcom,ipq8062", "qcom,ipq8064"; + + memory { + device_type = "memory"; + reg = <0x42000000 0x1e000000>; + }; + + aliases { + label-mac-device = &gmac2; + + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_red; + }; + + keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&buttons_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + + mode0 { + label = "mode0"; + gpios = <&qcom_pinmux 40 GPIO_ACTIVE_LOW>; + linux,code = <BTN_0>; + linux,input-type = <EV_SW>; + }; + + mode1 { + label = "mode1"; + gpios = <&qcom_pinmux 41 GPIO_ACTIVE_LOW>; + linux,code = <BTN_1>; + linux,input-type = <EV_SW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-0 = <&leds_pins>; + pinctrl-names = "default"; + + led_power_green: power_green { + label = "green:power"; + gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>; + }; + + led_power_red: power_red { + label = "red:power"; + gpios = <&qcom_pinmux 35 GPIO_ACTIVE_HIGH>; + }; + + active_green { + label = "green:active"; + gpios = <&qcom_pinmux 42 GPIO_ACTIVE_HIGH>; + }; + + active_red { + label = "red:active"; + gpios = <&qcom_pinmux 38 GPIO_ACTIVE_HIGH>; + }; + + wlan2g_green { + label = "green:wlan2g"; + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + + wlan2g_red { + label = "red:wlan2g"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; + }; + + wlan5g_green { + label = "green:wlan5g"; + gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g_red { + label = "red:wlan5g"; + gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>; + }; + + tv_green { + label = "green:tv"; + gpios = <&qcom_pinmux 46 GPIO_ACTIVE_HIGH>; + }; + + tv_red { + label = "red:tv"; + gpios = <&qcom_pinmux 36 GPIO_ACTIVE_HIGH>; + }; + + converter_green { + label = "green:converter"; + gpios = <&qcom_pinmux 43 GPIO_ACTIVE_HIGH>; + }; + + converter_red { + label = "red:converter"; + gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + pinctrl-0 = <&akro_pins>; + pinctrl-names = "default"; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + drive-strength = <10>; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + buttons_pins: buttons_pins { + mux { + pins = "gpio22", "gpio24", "gpio40", + "gpio41"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + leds_pins: leds_pins { + mux { + pins = "gpio14", "gpio15", "gpio35", + "gpio36", "gpio38", "gpio42", + "gpio43", "gpio46", "gpio55", + "gpio56", "gpio57", "gpio58"; + function = "gpio"; + bias-pull-down; + }; + + akro2 { + pins = "gpio15", "gpio35", "gpio38", + "gpio42", "gpio43", "gpio46", + "gpio55", "gpio56", "gpio57", + "gpio58"; + drive-strength = <2>; + }; + + akro4 { + pins = "gpio14", "gpio36"; + drive-strength = <4>; + }; + }; + + /* + * Stock firmware has the following settings, so let's do the same. + * I don't sure why these are required. + */ + akro_pins: akro_pinmux { + akro { + pins = "gpio17", "gpio26", "gpio47"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + reset { + pins = "gpio45"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + gmac0_rgmii { + pins = "gpio25"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; +}; + +&gsbi5 { + status = "okay"; + qcom,mode = <GSBI_PROT_SPI>; + + spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0000000 0x0020000>; + read-only; + }; + + partition@20000 { + label = "MIBIB"; + reg = <0x0020000 0x0020000>; + read-only; + }; + + partition@40000 { + label = "SBL2"; + reg = <0x0040000 0x0040000>; + read-only; + }; + + partition@80000 { + label = "SBL3"; + reg = <0x0080000 0x0080000>; + read-only; + }; + + partition@100000 { + label = "DDRCONFIG"; + reg = <0x0100000 0x0010000>; + read-only; + }; + + partition@110000 { + label = "SSD"; + reg = <0x0110000 0x0010000>; + read-only; + }; + + partition@120000 { + label = "TZ"; + reg = <0x0120000 0x0080000>; + read-only; + }; + + partition@1a0000 { + label = "RPM"; + reg = <0x01a0000 0x0080000>; + read-only; + }; + + partition@220000 { + label = "APPSBL"; + reg = <0x0220000 0x0080000>; + read-only; + }; + + partition@2a0000 { + label = "APPSBLENV"; + reg = <0x02a0000 0x0010000>; + read-only; + }; + + factory: partition@2b0000 { + label = "PRODUCTDATA"; + reg = <0x02b0000 0x0030000>; + read-only; + }; + + partition@2e0000 { + label = "ART"; + reg = <0x02e0000 0x0040000>; + read-only; + }; + + partition@320000 { + label = "TP"; + reg = <0x0320000 0x0040000>; + read-only; + }; + + partition@360000 { + label = "TINY"; + reg = <0x0360000 0x0500000>; + read-only; + }; + + partition@860000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x0860000 0x17a0000>; + }; + }; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + + qcom,ath10k-calibration-variant = "NEC-Platforms-WG2600HP3"; + }; + }; +}; + +&pcie1 { + status = "okay"; + force_gen1 = <1>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + + ieee80211-freq-limit = <2400000 2483000>; + qcom,ath10k-calibration-variant = "NEC-Platforms-WG2600HP3"; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x04 0x80080080 /* PAD0_MODE */ + 0x0c 0x06000000 /* PAD6_MODE */ + 0x10 0x002613a0 /* PWS_REG */ + 0x50 0xcc36cc36 /* LED_CTRL0 */ + 0x54 0xca36ca36 /* LED_CTRL1 */ + 0x58 0xc936c936 /* LED_CTRL2 */ + 0x5c 0x03ffff00 /* LED_CTRL3 */ + 0x7c 0x0000004e /* PORT0_STATUS */ + 0x94 0x0000004e /* PORT6_STATUS */ + 0xe0 0xc74164de /* SGMII_CTRL */ + 0xe4 0x0006a545 /* MAC_PWR_SEL */ + >; + }; +}; + +&gmac1 { + status = "okay"; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + phy-mode = "rgmii"; + qcom,id = <1>; + mdiobus = <&mdio0>; + mtd-mac-address = <&factory 0x0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + mdiobus = <&mdio0>; + mtd-mac-address = <&factory 0x6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index ad7c4b94d2..80bfec5ad9 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -193,6 +193,20 @@ define Device/nec_wg2600hp endef TARGET_DEVICES += nec_wg2600hp +define Device/nec_wg2600hp3 + $(call Device/LegacyImage) + DEVICE_VENDOR := NEC Platforms + DEVICE_MODEL := Aterm WG2600HP3 + SOC := qcom-ipq8062 + BLOCKSIZE := 64k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := -kmod-ata-ahci -kmod-ata-ahci-platform -kmod-usb-ohci -kmod-usb2 \ + -kmod-usb-ledtrig-usbport -kmod-usb-phy-qcom-dwc3 -kmod-usb3 -kmod-usb-dwc3-qcom \ + ath10k-firmware-qca9984-ct ipq-wifi-nec_wg2600hp3 +endef +TARGET_DEVICES += nec_wg2600hp3 + define Device/netgear_d7800 $(call Device/DniImage) DEVICE_VENDOR := NETGEAR diff --git a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch index 6bbf184ac7..795684cdf5 100644 --- a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch @@ -10,9 +10,10 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -843,6 +843,21 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -843,6 +843,22 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ ++ qcom-ipq8062-wg2600hp3.dtb \ qcom-ipq8064-ap148.dtb \ + qcom-ipq8064-c2600.dtb \ + qcom-ipq8064-d7800.dtb \ |