1 files changed, 0 insertions, 83 deletions
diff --git a/target/linux/ipq806x/patches/0180-ARM-dts-Add-ADM-DMA-nodes-and-SPI-linkage.patch b/target/linux/ipq806x/patches/0180-ARM-dts-Add-ADM-DMA-nodes-and-SPI-linkage.patch
deleted file mode 100644
index 05279de594..0000000000
--- a/target/linux/ipq806x/patches/0180-ARM-dts-Add-ADM-DMA-nodes-and-SPI-linkage.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From c78ae23b6c174c9f2e0973a247942b6b4adb7e82 Mon Sep 17 00:00:00 2001
-From: Andy Gross <agross@codeaurora.org>
-Date: Thu, 26 Jun 2014 13:02:59 -0500
-Subject: [PATCH 180/182] ARM: dts: Add ADM DMA nodes and SPI linkage
-
-This patch adds the ADM DMA controller DT nodes and also enables the use of dma
-in SPI.
-
-Signed-off-by: Andy Gross <agross@codeaurora.org>
----
- arch/arm/boot/dts/qcom-ipq8064-ap148.dts |   11 +++++++++++
- arch/arm/boot/dts/qcom-ipq8064.dtsi      |    8 +++++---
- 2 files changed, 16 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-@@ -44,6 +44,10 @@
- 					drive-strength = <10>;
- 					bias-none;
- 				};
-+				cs {
-+					pins = "gpio20";
-+					drive-strength = <12>;
-+				};
- 			};
- 			nand_pins: nand_pins {
- 				mux {
-@@ -100,12 +104,17 @@
- 
- 				cs-gpios = <&qcom_pinmux 20 0>;
- 
-+				dmas = <&adm_dma 6 9>,
-+					<&adm_dma 5 10>;
-+				dma-names = "rx", "tx";
-+
- 				flash: m25p80@0 {
- 					compatible = "s25fl256s1";
- 					#address-cells = <1>;
- 					#size-cells = <1>;
- 					spi-max-frequency = <50000000>;
- 					reg = <0>;
-+					m25p,fast-read;
- 
- 					partition@0 {
- 						label = "rootfs";
-@@ -140,8 +149,10 @@
- 			ranges = <0x00000000 0 0x00000000 0x31f00000 0 0x00100000   /* configuration space */
- 				  0x81000000 0 0	  0x31e00000 0 0x00100000   /* downstream I/O */
- 				  0x82000000 0 0x00000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
-+
- 		};
- 
-+
- 		sata-phy@1b400000 {
- 			status = "ok";
- 		};
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -421,19 +421,21 @@
- 			compatible = "qcom,adm";
- 			reg = <0x18300000 0x100000>;
- 			interrupts = <0 170 0>;
-+			#dma-cells = <2>;
- 
- 			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
--			clock-names = "core_clk", "iface_clk";
-+			clock-names = "core", "iface";
- 
- 			resets = <&gcc ADM0_RESET>,
- 				<&gcc ADM0_PBUS_RESET>,
- 				<&gcc ADM0_C0_RESET>,
- 				<&gcc ADM0_C1_RESET>,
- 				<&gcc ADM0_C2_RESET>;
--
--			reset-names = "adm", "pbus", "c0", "c1", "c2";
-+			reset-names = "clk", "pbus", "c0", "c1", "c2";
-+			qcom,ee = <0>;
- 
- 			status = "disabled";
-+
- 		};
- 
- 		nand@0x1ac00000 {