diff options
Diffstat (limited to 'target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts')
-rw-r--r-- | target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts | 488 |
1 files changed, 244 insertions, 244 deletions
diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts index ef31bf00b0..22937599e5 100644 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts +++ b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts @@ -36,220 +36,6 @@ }; soc { - pinmux@800000 { - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", - "gpio26", "gpio53", "gpio56", "gpio66"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "mdio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = <GSBI_PROT_SPI>; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - W25Q128@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x40000>; - read-only; - }; - - SBL3@80000 { - label = "SBL3"; - reg = <0x80000 0x80000>; - read-only; - }; - - DDRCONFIG@100000 { - label = "DDRCONFIG"; - reg = <0x100000 0x10000>; - read-only; - }; - - SSD@110000 { - label = "SSD"; - reg = <0x110000 0x10000>; - read-only; - }; - - TZ@120000 { - label = "TZ"; - reg = <0x120000 0x80000>; - read-only; - }; - - RPM@1a0000 { - label = "RPM"; - reg = <0x1a0000 0x80000>; - read-only; - }; - - APPSBL@220000 { - label = "APPSBL"; - reg = <0x220000 0x80000>; - read-only; - }; - - APPSBLENV@2a0000 { - label = "APPSBLENV"; - reg = <0x2a0000 0x40000>; - read-only; - }; - - OLDART@2e0000 { - label = "OLDART"; - reg = <0x2e0000 0x40000>; - read-only; - }; - - kernel@320000 { - label = "kernel"; - reg = <0x320000 0x300000>; - }; - - rootfs@620000 { - label = "rootfs"; - reg = <0x620000 0x960000>; - }; - - defaultmac: default-mac@0xfaf100 { - label = "default-mac"; - reg = <0xfaf100 0x00200>; - read-only; - }; - - ART@fc0000 { - label = "ART"; - reg = <0xfc0000 0x40000>; - read-only; - }; - }; - }; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - force_gen1 = <1>; - }; - mdio0: mdio@37000000 { #address-cells = <1>; #size-cells = <0>; @@ -281,36 +67,6 @@ reg = <4>; }; }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&defaultmac 0>; - mtd-mac-address-increment = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&defaultmac 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; }; keys { @@ -402,6 +158,250 @@ }; }; +&qcom_pinmux { + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", + "gpio26", "gpio53", "gpio56", "gpio66"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + i2c4_pins: i2c4_pinmux { + mux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "mdio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; +}; + +&gsbi4 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "okay"; + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; + +&gsbi5 { + qcom,mode = <GSBI_PROT_SPI>; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + W25Q128@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x40000>; + read-only; + }; + + SBL3@80000 { + label = "SBL3"; + reg = <0x80000 0x80000>; + read-only; + }; + + DDRCONFIG@100000 { + label = "DDRCONFIG"; + reg = <0x100000 0x10000>; + read-only; + }; + + SSD@110000 { + label = "SSD"; + reg = <0x110000 0x10000>; + read-only; + }; + + TZ@120000 { + label = "TZ"; + reg = <0x120000 0x80000>; + read-only; + }; + + RPM@1a0000 { + label = "RPM"; + reg = <0x1a0000 0x80000>; + read-only; + }; + + APPSBL@220000 { + label = "APPSBL"; + reg = <0x220000 0x80000>; + read-only; + }; + + APPSBLENV@2a0000 { + label = "APPSBLENV"; + reg = <0x2a0000 0x40000>; + read-only; + }; + + OLDART@2e0000 { + label = "OLDART"; + reg = <0x2e0000 0x40000>; + read-only; + }; + + kernel@320000 { + label = "kernel"; + reg = <0x320000 0x300000>; + }; + + rootfs@620000 { + label = "rootfs"; + reg = <0x620000 0x960000>; + }; + + defaultmac: default-mac@0xfaf100 { + label = "default-mac"; + reg = <0xfaf100 0x00200>; + read-only; + }; + + ART@fc0000 { + label = "ART"; + reg = <0xfc0000 0x40000>; + read-only; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + force_gen1 = <1>; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&defaultmac 0>; + mtd-mac-address-increment = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&defaultmac 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + &adm_dma { status = "okay"; }; |