diff options
Diffstat (limited to 'target/linux/ipq806x/files-4.9')
14 files changed, 0 insertions, 6037 deletions
diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-ap148.dts deleted file mode 100644 index a3df82909e..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-ap148.dts +++ /dev/null @@ -1,250 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm IPQ8064/AP148"; - compatible = "qcom,ipq8064-ap148", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - }; - - chosen { - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - i2c4_pins: i2c4_pinmux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - bias-disable; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - }; - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38", "gpio39", - "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - pullups { - pins = "gpio39"; - bias-pull-up; - }; - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = <GSBI_PROT_SPI>; - status = "ok"; - - spi4: spi@1a280000 { - status = "ok"; - spi-max-frequency = <50000000>; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 0>; - - flash: m25p80@0 { - compatible = "s25fl256s1"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; - }; - - sata-phy@1b400000 { - status = "ok"; - }; - - sata@29000000 { - status = "ok"; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - }; - - usb30@1 { - status = "ok"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "ok"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-c2600.dts deleted file mode 100644 index 78caf23f3a..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-c2600.dts +++ /dev/null @@ -1,495 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include <dt-bindings/input/input.h> - -/ { - model = "TP-Link Archer C2600"; - compatible = "tplink,c2600", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &general; - led-running = &power; - led-upgrade = &general; - }; - - chosen { - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio16", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33", - "gpio53", "gpio66"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb0_pwr_en_pin: usb0_pwr_en_pin { - mux { - pins = "gpio25"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - output-high; - }; - }; - - usb1_pwr_en_pin: usb1_pwr_en_pin { - mux { - pins = "gpio23"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = <GSBI_PROT_SPI>; - status = "ok"; - - spi5: spi@1a280000 { - status = "ok"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash: m25p80@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x20000>; - read-only; - }; - - SBL3@60000 { - label = "SBL3"; - reg = <0x60000 0x30000>; - read-only; - }; - - DDRCONFIG@90000 { - label = "DDRCONFIG"; - reg = <0x90000 0x10000>; - read-only; - }; - - SSD@a0000 { - label = "SSD"; - reg = <0xa0000 0x10000>; - read-only; - }; - - TZ@b0000 { - label = "TZ"; - reg = <0xb0000 0x30000>; - read-only; - }; - - RPM@e0000 { - label = "RPM"; - reg = <0xe0000 0x20000>; - read-only; - }; - - fs-uboot@100000 { - label = "fs-uboot"; - reg = <0x100000 0x70000>; - read-only; - }; - - uboot-env@170000 { - label = "uboot-env"; - reg = <0x170000 0x40000>; - read-only; - }; - - radio@1b0000 { - label = "radio"; - reg = <0x1b0000 0x40000>; - read-only; - }; - - os-image@1f0000 { - label = "os-image"; - reg = <0x1f0000 0x200000>; - }; - - rootfs@3f0000 { - label = "rootfs"; - reg = <0x3f0000 0x1b00000>; - }; - - defaultmac: default-mac@1ef0000 { - label = "default-mac"; - reg = <0x1ef0000 0x00200>; - read-only; - }; - - pin@1ef0200 { - label = "pin"; - reg = <0x1ef0200 0x00200>; - read-only; - }; - - product-info@1ef0400 { - label = "product-info"; - reg = <0x1ef0400 0x0fc00>; - read-only; - }; - - partition-table@1f00000 { - label = "partition-table"; - reg = <0x1f00000 0x10000>; - read-only; - }; - - soft-version@1f10000 { - label = "soft-version"; - reg = <0x1f10000 0x10000>; - read-only; - }; - - support-list@1f20000 { - label = "support-list"; - reg = <0x1f20000 0x10000>; - read-only; - }; - - profile@1f30000 { - label = "profile"; - reg = <0x1f30000 0x10000>; - read-only; - }; - - default-config@1f40000 { - label = "default-config"; - reg = <0x1f40000 0x10000>; - read-only; - }; - - user-config@1f50000 { - label = "user-config"; - reg = <0x1f50000 0x40000>; - read-only; - }; - - qos-db@1f90000 { - label = "qos-db"; - reg = <0x1f90000 0x40000>; - read-only; - }; - - usb-config@1fd0000 { - label = "usb-config"; - reg = <0x1fd0000 0x10000>; - read-only; - }; - - log@1fe0000 { - label = "log"; - reg = <0x1fe0000 0x20000>; - read-only; - }; - }; - }; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - - pinctrl-0 = <&usb0_pwr_en_pin>; - pinctrl-names = "default"; - }; - - usb30@1 { - status = "ok"; - - pinctrl-0 = <&usb1_pwr_en_pin>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - force_gen1 = <1>; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&defaultmac 0x8>; - mtd-mac-address-increment = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&defaultmac 0x8>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - }; - - ledswitch { - label = "ledswitch"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; - linux,code = <KEY_LIGHTS_TOGGLE>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - lan { - label = "c2600:white:lan"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; - }; - - usb4 { - label = "c2600:white:usb_4"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "c2600:white:usb_2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "c2600:white:wps"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "c2600:amber:wan"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; - }; - - wan_white { - label = "c2600:white:wan"; - gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>; - }; - - power: power { - label = "c2600:white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - general: general { - label = "c2600:white:general"; - gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-d7800.dts deleted file mode 100644 index 514ddb5014..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-d7800.dts +++ /dev/null @@ -1,414 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include <dt-bindings/input/input.h> - -/ { - model = "Netgear Nighthawk X4 D7800"; - compatible = "netgear,d7800", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0xe000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38", "gpio39", - "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - pullups { - pins = "gpio39"; - bias-pull-up; - }; - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "ok"; - }; - - sata@29000000 { - status = "ok"; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb30@1 { - status = "ok"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "ok"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - #address-cells = <1>; - #size-cells = <1>; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x1C00000>; - }; - - netgear@3480000 { - label = "netgear"; - reg = <0x3480000 0x4480000>; - read-only; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - - firmware@1480000 { - label = "firmware"; - reg = <0x1480000 0x2000000>; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - phy-handle = <&phy4>; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "d7800:white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "d7800:white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - power_amber: power_amber { - label = "d7800:amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "d7800:white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "d7800:amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "d7800:white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "d7800:white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power_white: power_white { - label = "d7800:white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "d7800:white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-db149.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-db149.dts deleted file mode 100644 index 4c56866077..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-db149.dts +++ /dev/null @@ -1,236 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm IPQ8064/DB149"; - compatible = "qcom,ipq8064-db149", "qcom,ipq8064"; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - alias { - serial0 = &uart2; - mdio-gpio0 = &mdio0; - }; - - chosen { - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - i2c4_pins: i2c4_pinmux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - bias-disable; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii0_pins: rgmii0_pins { - mux { - pins = "gpio2", "gpio66"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi2: gsbi@12480000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - uart2: serial@12490000 { - status = "ok"; - }; - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = <GSBI_PROT_SPI>; - status = "ok"; - - spi4: spi@1a280000 { - status = "ok"; - spi-max-frequency = <50000000>; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 0>; - - flash: m25p80@0 { - compatible = "s25fl256s1"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - m25p,fast-read; - - partition@0 { - label = "lowlevel_init"; - reg = <0x0 0x1b0000>; - }; - - partition@1 { - label = "u-boot"; - reg = <0x1b0000 0x80000>; - }; - - partition@2 { - label = "u-boot-env"; - reg = <0x230000 0x40000>; - }; - - partition@3 { - label = "caldata"; - reg = <0x270000 0x40000>; - }; - - partition@4 { - label = "firmware"; - reg = <0x2b0000 0x1d50000>; - }; - }; - }; - }; - - sata-phy@1b400000 { - status = "ok"; - }; - - sata@29000000 { - status = "ok"; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - }; - - usb30@1 { - status = "ok"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - }; - - pcie2: pci@1b900000 { - status = "ok"; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - - phy6: ethernet-phy@6 { - device_type = "ethernet-phy"; - reg = <6>; - }; - - phy7: ethernet-phy@7 { - device_type = "ethernet-phy"; - reg = <7>; - }; - }; - - gmac0: ethernet@37000000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <0>; - phy-handle = <&phy4>; - - pinctrl-0 = <&rgmii0_pins>; - pinctrl-names = "default"; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - phy-handle = <&phy6>; - }; - - gmac3: ethernet@37600000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <3>; - phy-handle = <&phy7>; - }; - }; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts deleted file mode 100644 index 56115ed89c..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts +++ /dev/null @@ -1,415 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include <dt-bindings/input/input.h> - -/ { - model = "Linksys EA8500 WiFi Router"; - compatible = "linksys,ea8500", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "console=ttyMSM0,115200n8"; - linux,stdout-path = "serial0:115200n8"; - append-rootblock = "ubi.mtd="; /* append to bootargs adding the root deviceblock nbr from bootloader */ - }; - - soc { - pinmux@800000 { - - pinctrl-0 = <&switch_reset>; - pinctrl-names = "default"; - - button_pins: button_pins { - mux { - pins = "gpio65", "gpio67", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio53", "gpio54"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - switch_reset: switch_reset_pins { - mux { - pins = "gpio63"; - function = "gpio"; - drive-strength = <2>; - bias-disable; - output-low; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38", "gpio39", - "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - pullups { - pins = "gpio39"; - bias-pull-up; - }; - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "ok"; - }; - - sata@29000000 { - status = "ok"; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - }; - - usb30@1 { - status = "ok"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - force_gen1 = <1>; - }; - - pcie1: pci@1b700000 { - status = "ok"; - }; - - nand@1ac00000 { - status = "ok"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0000000 0x0040000>; - read-only; - }; - - MIBIB@40000 { - label = "MIBIB"; - reg = <0x0040000 0x0140000>; - read-only; - }; - - SBL2@180000 { - label = "SBL2"; - reg = <0x0180000 0x0140000>; - read-only; - }; - - SBL3@2c0000 { - label = "SBL3"; - reg = <0x02c0000 0x0280000>; - read-only; - }; - - DDRCONFIG@540000 { - label = "DDRCONFIG"; - reg = <0x0540000 0x0120000>; - read-only; - }; - - SSD@660000 { - label = "SSD"; - reg = <0x0660000 0x0120000>; - read-only; - }; - - TZ@780000 { - label = "TZ"; - reg = <0x0780000 0x0280000>; - read-only; - }; - - RPM@a00000 { - label = "RPM"; - reg = <0x0a00000 0x0280000>; - read-only; - }; - - art: art@c80000 { - label = "art"; - reg = <0x0c80000 0x0140000>; - read-only; - }; - - APPSBL@dc0000 { - label = "APPSBL"; - reg = <0x0dc0000 0x0100000>; - read-only; - }; - - u_env@ec0000 { - label = "u_env"; - reg = <0x0ec0000 0x0040000>; - }; - - s_env@f00000 { - label = "s_env"; - reg = <0x0f00000 0x0040000>; - }; - - devinfo@f40000 { - label = "devinfo"; - reg = <0x0f40000 0x0040000>; - }; - - linux@f80000 { - label = "kernel1"; - reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/ - }; - - rootfs@1280000 { - label = "rootfs1"; - reg = <0x1280000 0x2500000>; - }; - - linux2@3780000 { - label = "kernel2"; - reg = <0x3780000 0x2800000>; - }; - - rootfs2@3a80000 { - label = "rootfs2"; - reg = <0x3a80000 0x2500000>; - }; - - syscfg@5f80000 { - label = "syscfg"; - reg = <0x5f80000 0x2080000>; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <1>; - qcom,rgmii_delay = <0>; - qcom,emulation = <0>; - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - //lan - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,emulation = <0>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - adm_dma: dma@18300000 { - status = "ok"; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART >; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - wps { - label = "ea8500:green:wps"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "ea8500:white:power"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - wifi { - label = "ea8500:green:wifi"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -/delete-node/ &pcie2_pins; -/delete-node/ &pcie2; - diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-r7500.dts deleted file mode 100644 index 7a209ece12..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-r7500.dts +++ /dev/null @@ -1,389 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -#include <dt-bindings/input/input.h> -#include <dt-bindings/soc/qcom,tcsr.h> - -/ { - model = "Netgear Nighthawk X4 R7500"; - compatible = "netgear,r7500", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0xe000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38", "gpio39", - "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - pullups { - pins = "gpio39"; - bias-pull-up; - }; - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "ok"; - }; - - sata@29000000 { - status = "ok"; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - clocks = <&gcc USB30_0_UTMI_CLK>; - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - clocks = <&gcc USB30_0_MASTER_CLK>; - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - clocks = <&gcc USB30_1_UTMI_CLK>; - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - clocks = <&gcc USB30_1_MASTER_CLK>; - status = "ok"; - }; - - usb30@0 { - clocks = <&gcc USB30_1_MASTER_CLK>; - status = "ok"; - }; - - usb30@1 { - clocks = <&gcc USB30_0_MASTER_CLK>; - status = "ok"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "ok"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - kernel@1340000 { - label = "kernel"; - reg = <0x1340000 0x0400000>; - }; - - ubi@1740000 { - label = "ubi"; - reg = <0x1740000 0x1600000>; - }; - - netgear@2d40000 { - label = "netgear"; - reg = <0x2d40000 0x0c00000>; - read-only; - }; - - reserve@3940000 { - label = "reserve"; - reg = <0x3940000 0x46c0000>; - read-only; - }; - - firmware@1340000 { - label = "firmware"; - reg = <0x1340000 0x1a00000>; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "r7500:white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "r7500:white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - power_amber: power_amber { - label = "r7500:amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "r7500:white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "r7500:amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "r7500:white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "r7500:white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power_white: power_white { - label = "r7500:white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "r7500:white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&tcsr { - qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>; - compatible = "qcom,tcsr"; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts deleted file mode 100644 index 089445fc3e..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts +++ /dev/null @@ -1,420 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include <dt-bindings/input/input.h> - -/ { - model = "Netgear Nighthawk X4 R7500v2"; - compatible = "netgear,r7500v2", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - - rsvd@5fe00000 { - reg = <0x5fe00000 0x200000>; - reusable; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38", "gpio39", - "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - pullups { - pins = "gpio39"; - bias-pull-up; - }; - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "ok"; - }; - - sata@29000000 { - status = "ok"; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb30@1 { - status = "ok"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "ok"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x1C00000>; - }; - - netgear@3480000 { - label = "netgear"; - reg = <0x3480000 0x4480000>; - read-only; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - - firmware@1480000 { - label = "firmware"; - reg = <0x1480000 0x2000000>; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "r7500v2:amber:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb3 { - label = "r7500v2:amber:usb3"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - status { - label = "r7500v2:amber:status"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - internet { - label = "r7500v2:white:internet"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan { - label = "r7500v2:white:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "r7500v2:white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "r7500v2:white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "r7500v2:white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "r7500v2:white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi deleted file mode 100644 index 8c522a897d..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi +++ /dev/null @@ -1,30 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - soc: soc { - - ss_phy_0: phy@110f8830 { - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <0xa0>; - }; - - ss_phy_1: phy@100f8830 { - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <0xa0>; - }; - - pcie0: pci@1b500000 { - phy-tx0-term-offset = <0>; - }; - - pcie1: pci@1b700000 { - phy-tx0-term-offset = <0>; - }; - - pcie2: pci@1b900000 { - phy-tx0-term-offset = <0>; - }; - }; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts deleted file mode 100644 index 0877527332..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts +++ /dev/null @@ -1,419 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include <dt-bindings/input/input.h> - -/ { - model = "TP-Link Archer VR2600v"; - compatible = "tplink,vr2600v", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &general; - led-running = &power; - led-upgrade = &general; - }; - - chosen { - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", - "gpio26", "gpio53", "gpio56", "gpio66"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = <GSBI_PROT_SPI>; - status = "ok"; - - spi4: spi@1a280000 { - status = "ok"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash: W25Q128@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x40000>; - read-only; - }; - - SBL3@80000 { - label = "SBL3"; - reg = <0x80000 0x80000>; - read-only; - }; - - DDRCONFIG@100000 { - label = "DDRCONFIG"; - reg = <0x100000 0x10000>; - read-only; - }; - - SSD@110000 { - label = "SSD"; - reg = <0x110000 0x10000>; - read-only; - }; - - TZ@120000 { - label = "TZ"; - reg = <0x120000 0x80000>; - read-only; - }; - - RPM@1a0000 { - label = "RPM"; - reg = <0x1a0000 0x80000>; - read-only; - }; - - APPSBL@220000 { - label = "APPSBL"; - reg = <0x220000 0x80000>; - read-only; - }; - - APPSBLENV@2a0000 { - label = "APPSBLENV"; - reg = <0x2a0000 0x40000>; - read-only; - }; - - OLDART@2e0000 { - label = "OLDART"; - reg = <0x2e0000 0x40000>; - read-only; - }; - - kernel@320000 { - label = "kernel"; - reg = <0x320000 0x300000>; - }; - - rootfs@620000 { - label = "rootfs"; - reg = <0x620000 0x960000>; - }; - - defaultmac: default-mac@0xfaf100 { - label = "default-mac"; - reg = <0xfaf100 0x00200>; - read-only; - }; - - ART@fc0000 { - label = "ART"; - reg = <0xfc0000 0x40000>; - read-only; - }; - }; - }; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - }; - - usb30@1 { - status = "ok"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - force_gen1 = <1>; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&defaultmac 0>; - mtd-mac-address-increment = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&defaultmac 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - }; - - dect { - label = "dect"; - gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; - linux,code = <KEY_PHONE>; - }; - - ledswitch { - label = "ledswitch"; - gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; - linux,code = <KEY_LIGHTS_TOGGLE>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - dsl { - label = "vr2600v:white:dsl"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb { - label = "vr2600v:white:usb"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - lan { - label = "vr2600v:white:lan"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wlan2g { - label = "vr2600v:white:wlan2g"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; - }; - - wlan5g { - label = "vr2600v:white:wlan5g"; - gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "vr2600v:white:power"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - phone { - label = "vr2600v:white:phone"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - wan { - label = "vr2600v:white:wan"; - gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; - }; - - general: general { - label = "vr2600v:white:general"; - gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts deleted file mode 100644 index 9440de5b8f..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts +++ /dev/null @@ -1,570 +0,0 @@ -/* - * BSD LICENSE - * - * Copyright (C) 2017 Christian Mehlis <christian@m3hlis.de> - * Copyright (C) 2018 Mathias Kresin <dev@kresin.me> - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * - * 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in the - * documentation and/or other materials provided with the distribution. - * 3. Neither the names of the copyright holders nor the names of any - * contributors may be used to endorse or promote products derived - * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - */ - -#include "qcom-ipq8064-v1.0.dtsi" - -#include <dt-bindings/input/input.h> -#include <dt-bindings/soc/qcom,tcsr.h> - -/ { - compatible = "compex,wpq864", "qcom,ipq8064"; - model = "Compex WPQ864"; - - aliases { - mdio-gpio0 = &mdio0; - serial0 = &gsbi4_serial; - ethernet0 = &gmac1; - ethernet1 = &gmac0; - - led-boot = &led_pass; - led-failsafe = &led_fail; - led-running = &led_pass; - led-upgrade = &led_pass; - }; - - chosen { - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - rpm@108000 { - pinctrl-0 = <&rpm_pins>; - pinctrl-names = "default"; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - mt29f2g08abbeah4@0 { - compatible = "qcom,nandcs"; - - reg = <0>; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0000000 0x0040000>; - read-only; - }; - - MIBIB@40000 { - label = "MIBIB"; - reg = <0x0040000 0x0140000>; - read-only; - }; - - SBL2@180000 { - label = "SBL2"; - reg = <0x0180000 0x0140000>; - read-only; - }; - - SBL3@2c0000 { - label = "SBL3"; - reg = <0x02c0000 0x0280000>; - read-only; - }; - - DDRCONFIG@540000 { - label = "DDRCONFIG"; - reg = <0x0540000 0x0120000>; - read-only; - }; - - SSD@660000 { - label = "SSD"; - reg = <0x0660000 0x0120000>; - read-only; - }; - - TZ@780000 { - label = "TZ"; - reg = <0x0780000 0x0280000>; - read-only; - }; - - RPM@a00000 { - label = "RPM"; - reg = <0x0a00000 0x0280000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - }; - - ART@1200000 { - label = "ART"; - reg = <0x1200000 0x0140000>; - }; - - ubi@1340000 { - label = "ubi"; - reg = <0x1340000 0x4000000>; - }; - - BOOTCONFIG@1340000 { - label = "BOOTCONFIG"; - reg = <0x5340000 0x0060000>; - }; - - SBL2-1@53a0000- { - label = "SBL2_1"; - reg = <0x53a0000 0x0140000>; - read-only; - }; - - SBL3-1@54e0000 { - label = "SBL3_1"; - reg = <0x54e0000 0x0280000>; - read-only; - }; - - DDRCONFIG-1@5760000 { - label = "DDRCONFIG_1"; - reg = <0x5760000 0x0120000>; - read-only; - }; - - SSD-1@5880000 { - label = "SSD_1"; - reg = <0x5880000 0x0120000>; - read-only; - }; - - TZ-1@59a0000 { - label = "TZ_1"; - reg = <0x59a0000 0x0280000>; - read-only; - }; - - RPM-1@5c20000 { - label = "RPM_1"; - reg = <0x5c20000 0x0280000>; - read-only; - }; - - BOOTCONFIG1@5ea0000 { - label = "BOOTCONFIG1"; - reg = <0x5ea0000 0x0060000>; - }; - - APPSBL-1@5f00000 { - label = "APPSBL_1"; - reg = <0x5f00000 0x0500000>; - read-only; - }; - - ubi-1@6400000 { - label = "ubi_1"; - reg = <0x6400000 0x4000000>; - }; - - unused@a400000 { - label = "unused"; - reg = <0xa400000 0x5c00000>; - }; - }; - }; - }; - }; - - mdio0: mdio { - #address-cells = <1>; - #size-cells = <0>; - - compatible = "virtual,mdio-gpio"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - - ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - rss4 { - label = "wpq864:green:rss4"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - rss3 { - label = "wpq864:green:rss3"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - rss2 { - label = "wpq864:orange:rss2"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; - }; - - rss1 { - label = "wpq864:red:rss1"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - led_pass: pass { - label = "wpq864:green:pass"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - led_fail: fail { - label = "wpq864:green:fail"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - usb { - label = "wpq864:green:usb"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb-pcie { - label = "wpq864:green:usb-pcie"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - }; - - beeper { - compatible = "gpio-beeper"; - - pinctrl-0 = <&beeper_pins>; - pinctrl-names = "default"; - - gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&gmac1 { - status = "okay"; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gsbi4 { - status = "okay"; - qcom,mode = <GSBI_PROT_I2C_UART>; -}; - -&gsbi4_serial { - status = "okay"; - - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; -}; - -&gsbi5 { - status = "okay"; - - qcom,mode = <GSBI_PROT_SPI>; - - spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - s25fl256s1@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0>; - spi-max-frequency = <50000000>; - }; - }; -}; - -&hs_phy_0 { /* USB3 port 0 HS phy */ - status = "okay"; -}; - -&hs_phy_1 { /* USB3 port 1 HS phy */ - status = "okay"; -}; - -&ss_phy_0 { /* USB3 port 0 SS phy */ - status = "okay"; - - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <160>; -}; - -&ss_phy_1 { /* USB3 port 1 SS phy */ - status = "okay"; - - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <160>; -}; - -&pcie0 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; -}; - -&pcie1 { - status = "okay"; -}; - -&pcie2 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; -}; - -&qcom_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinctrl0 { - pcie0_pcie2_perst { - pins = "gpio3"; - function = "gpio"; - drive-strength = <2>; - bias-disable; - output-high; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", - "gpio23", "gpio24", "gpio25", "gpio53"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio54"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - beeper_pins: beeper_pins { - mux { - pins = "gpio55"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - rpm_pins: rpm_pins { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <10>; - bias-disable; - }; - }; - - uart0_pins: uart0_pins { - mux { - pins = "gpio10", "gpio11"; - function = "gsbi4"; - drive-strength = <10>; - bias-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19"; - function = "gsbi5"; - drive-strength = <10>; - bias-pull-down; - }; - - clk { - pins = "gpio21"; - function = "gsbi5"; - drive-strength = <12>; - bias-pull-down; - }; - - cs { - pins = "gpio20"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - }; - }; - - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", "gpio37", - "gpio38", "gpio39", "gpio40", "gpio41", - "gpio42", "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", "gpio43", - "gpio44", "gpio45", "gpio46", "gpio47"; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", - "gpio31", "gpio32", "gpio51", "gpio52", - "gpio59", "gpio60", "gpio61", "gpio62"; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; -}; - -&usb3_0 { - status = "okay"; -}; - - -&usb3_1 { - status = "okay"; -}; - -&tcsr { - qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064.dtsi b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064.dtsi deleted file mode 100644 index 942e1fd97b..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ /dev/null @@ -1,1408 +0,0 @@ -/dts-v1/; - -#include "skeleton.dtsi" -#include <dt-bindings/clock/qcom,gcc-ipq806x.h> -#include <dt-bindings/mfd/qcom-rpm.h> -#include <dt-bindings/clock/qcom,rpmcc.h> -#include <dt-bindings/clock/qcom,lcc-ipq806x.h> -#include <dt-bindings/soc/qcom,gsbi.h> -#include <dt-bindings/reset/qcom,gcc-ipq806x.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/gpio/gpio.h> - -/ { - model = "Qualcomm IPQ8064"; - compatible = "qcom,ipq8064"; - interrupt-parent = <&intc>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu0: cpu@0 { - compatible = "qcom,krait"; - enable-method = "qcom,kpss-acc-v1"; - device_type = "cpu"; - reg = <0>; - next-level-cache = <&L2>; - qcom,acc = <&acc0>; - qcom,saw = <&saw0>; - clocks = <&kraitcc 0>, <&kraitcc 4>; - clock-names = "cpu", "l2"; - clock-latency = <100000>; - cpu-supply = <&smb208_s2a>; - voltage-tolerance = <5>; - cooling-min-state = <0>; - cooling-max-state = <10>; - #cooling-cells = <2>; - cpu-idle-states = <&CPU_SPC>; - }; - - cpu1: cpu@1 { - compatible = "qcom,krait"; - enable-method = "qcom,kpss-acc-v1"; - device_type = "cpu"; - reg = <1>; - next-level-cache = <&L2>; - qcom,acc = <&acc1>; - qcom,saw = <&saw1>; - clocks = <&kraitcc 1>, <&kraitcc 4>; - clock-names = "cpu", "l2"; - clock-latency = <100000>; - cpu-supply = <&smb208_s2b>; - cooling-min-state = <0>; - cooling-max-state = <10>; - #cooling-cells = <2>; - cpu-idle-states = <&CPU_SPC>; - }; - - L2: l2-cache { - compatible = "cache"; - cache-level = <2>; - qcom,saw = <&saw_l2>; - }; - - qcom,l2 { - qcom,l2-rates = <384000000 1000000000 1200000000>; - }; - - idle-states { - CPU_SPC: spc { - compatible = "qcom,idle-state-spc", - "arm,idle-state"; - entry-latency-us = <400>; - exit-latency-us = <900>; - min-residency-us = <3000>; - }; - }; - }; - - thermal-zones { - tsens_tz_sensor0 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 0>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor1 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 1>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor2 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 2>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor3 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 3>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor4 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 4>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor5 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 5>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor6 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 6>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor7 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 7>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor8 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 8>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor9 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 9>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor10 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 10>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - }; - - cpu-pmu { - compatible = "qcom,krait-pmu"; - interrupts = <1 10 0x304>; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - nss@40000000 { - reg = <0x40000000 0x1000000>; - no-map; - }; - - smem: smem@41000000 { - reg = <0x41000000 0x200000>; - no-map; - }; - }; - - clocks { - cxo_board { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <25000000>; - }; - - pxo_board { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <25000000>; - }; - - sleep_clk: sleep_clk { - compatible = "fixed-clock"; - clock-frequency = <32768>; - #clock-cells = <0>; - }; - }; - - firmware { - scm { - compatible = "qcom,scm-ipq806x"; - }; - }; - - kraitcc: clock-controller { - compatible = "qcom,krait-cc-v1"; - #clock-cells = <1>; - }; - - qcom,pvs { - qcom,pvs-format-a; - qcom,speed0-pvs0-bin-v0 = - < 1400000000 1250000 >, - < 1200000000 1200000 >, - < 1000000000 1150000 >, - < 800000000 1100000 >, - < 600000000 1050000 >, - < 384000000 1000000 >; - - qcom,speed0-pvs1-bin-v0 = - < 1400000000 1175000 >, - < 1200000000 1125000 >, - < 1000000000 1075000 >, - < 800000000 1025000 >, - < 600000000 975000 >, - < 384000000 925000 >; - - qcom,speed0-pvs2-bin-v0 = - < 1400000000 1125000 >, - < 1200000000 1075000 >, - < 1000000000 1025000 >, - < 800000000 995000 >, - < 600000000 925000 >, - < 384000000 875000 >; - - qcom,speed0-pvs3-bin-v0 = - < 1400000000 1050000 >, - < 1200000000 1000000 >, - < 1000000000 950000 >, - < 800000000 900000 >, - < 600000000 850000 >, - < 384000000 800000 >; - }; - - soc: soc { - #address-cells = <1>; - #size-cells = <1>; - ranges; - compatible = "simple-bus"; - - lpass@28100000 { - compatible = "qcom,lpass-cpu"; - status = "disabled"; - clocks = <&lcc AHBIX_CLK>, - <&lcc MI2S_OSR_CLK>, - <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", - "mi2s-osr-clk", - "mi2s-bit-clk"; - interrupts = <0 85 1>; - interrupt-names = "lpass-irq-lpaif"; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; - }; - - qfprom: qfprom@700000 { - compatible = "qcom,qfprom", "syscon"; - reg = <0x700000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - status = "okay"; - tsens_calib: calib@400 { - reg = <0x400 0x10>; - }; - tsens_backup: backup@410 { - reg = <0x410 0x10>; - }; - }; - - rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; - qcom,ipc = <&l2cc 0x8 2>; - - interrupts = <0 19 0>, - <0 21 0>, - <0 22 0>; - interrupt-names = "ack", - "err", - "wakeup"; - - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; - - #address-cells = <1>; - #size-cells = <0>; - - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; - - regulators { - compatible = "qcom,rpm-smb208-regulators"; - - smb208_s1a: s1a { - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1150000>; - - qcom,switch-mode-frequency = <1200000>; - - }; - - smb208_s1b: s1b { - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1150000>; - - qcom,switch-mode-frequency = <1200000>; - }; - - smb208_s2a: s2a { - regulator-min-microvolt = < 800000>; - regulator-max-microvolt = <1250000>; - - qcom,switch-mode-frequency = <1200000>; - }; - - smb208_s2b: s2b { - regulator-min-microvolt = < 800000>; - regulator-max-microvolt = <1250000>; - - qcom,switch-mode-frequency = <1200000>; - }; - }; - }; - - rng@1a500000 { - compatible = "qcom,prng"; - reg = <0x1a500000 0x200>; - clocks = <&gcc PRNG_CLK>; - clock-names = "core"; - }; - - qcom_pinmux: pinmux@800000 { - compatible = "qcom,ipq8064-pinctrl"; - reg = <0x800000 0x4000>; - - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = <0 16 0x4>; - - pcie0_pins: pcie0_pinmux { - mux { - pins = "gpio3"; - function = "pcie1_rst"; - drive-strength = <2>; - bias-disable; - }; - }; - - pcie1_pins: pcie1_pinmux { - mux { - pins = "gpio48"; - function = "pcie2_rst"; - drive-strength = <2>; - bias-disable; - }; - }; - - pcie2_pins: pcie2_pinmux { - mux { - pins = "gpio63"; - function = "pcie3_rst"; - drive-strength = <2>; - bias-disable; - output-low; - }; - }; - }; - - intc: interrupt-controller@2000000 { - compatible = "qcom,msm-qgic2"; - interrupt-controller; - #interrupt-cells = <3>; - reg = <0x02000000 0x1000>, - <0x02002000 0x1000>; - }; - - timer@200a000 { - compatible = "qcom,kpss-timer", "qcom,msm-timer"; - interrupts = <1 1 0x301>, - <1 2 0x301>, - <1 3 0x301>, - <1 4 0x301>, - <1 5 0x301>; - reg = <0x0200a000 0x100>; - clock-frequency = <25000000>, - <32768>; - clocks = <&sleep_clk>; - clock-names = "sleep"; - cpu-offset = <0x80000>; - }; - - acc0: clock-controller@2088000 { - compatible = "qcom,kpss-acc-v1"; - reg = <0x02088000 0x1000>, <0x02008000 0x1000>; - clock-output-names = "acpu0_aux"; - }; - - acc1: clock-controller@2098000 { - compatible = "qcom,kpss-acc-v1"; - reg = <0x02098000 0x1000>, <0x02008000 0x1000>; - clock-output-names = "acpu1_aux"; - }; - - l2cc: clock-controller@2011000 { - compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; - clock-output-names = "acpu_l2_aux"; - }; - - saw0: regulator@2089000 { - compatible = "qcom,saw2", "syscon"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; - }; - - saw1: regulator@2099000 { - compatible = "qcom,saw2", "syscon"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; - }; - - saw_l2: regulator@02012000 { - compatible = "qcom,saw2", "syscon"; - reg = <0x02012000 0x1000>; - regulator; - }; - - sic_non_secure: sic-non-secure@12100000 { - compatible = "syscon"; - reg = <0x12100000 0x10000>; - }; - - gsbi2: gsbi@12480000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <2>; - reg = <0x12480000 0x100>; - clocks = <&gcc GSBI2_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - uart2: serial@12490000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x12490000 0x1000>, - <0x12480000 0x1000>; - interrupts = <0 195 0x0>; - clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@124a0000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x124a0000 0x1000>; - interrupts = <0 196 0>; - - clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - }; - - gsbi4: gsbi@16300000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <4>; - reg = <0x16300000 0x100>; - clocks = <&gcc GSBI4_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi4_serial: serial@16340000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x16340000 0x1000>, - <0x16300000 0x1000>; - interrupts = <0 152 0x0>; - clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@16380000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x16380000 0x1000>; - interrupts = <0 153 0>; - - clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - - gsbi5: gsbi@1a200000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <5>; - reg = <0x1a200000 0x100>; - clocks = <&gcc GSBI5_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - uart5: serial@1a240000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x1a240000 0x1000>, - <0x1a200000 0x1000>; - interrupts = <0 154 0x0>; - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@1a280000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <0 155 0>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - spi@1a280000 { - compatible = "qcom,spi-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <0 155 0>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - - sata_phy: sata-phy@1b400000 { - compatible = "qcom,ipq806x-sata-phy"; - reg = <0x1b400000 0x200>; - - clocks = <&gcc SATA_PHY_CFG_CLK>; - clock-names = "cfg"; - - #phy-cells = <0>; - status = "disabled"; - }; - - sata@29000000 { - compatible = "qcom,ipq806x-ahci", "generic-ahci"; - reg = <0x29000000 0x180>; - - interrupts = <0 209 0x0>; - - clocks = <&gcc SFAB_SATA_S_H_CLK>, - <&gcc SATA_H_CLK>, - <&gcc SATA_A_CLK>, - <&gcc SATA_RXOOB_CLK>, - <&gcc SATA_PMALIVE_CLK>; - clock-names = "slave_face", "iface", "core", - "rxoob", "pmalive"; - - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; - assigned-clock-rates = <100000000>, <100000000>; - - phys = <&sata_phy>; - phy-names = "sata-phy"; - status = "disabled"; - }; - - qcom,ssbi@500000 { - compatible = "qcom,ssbi"; - reg = <0x00500000 0x1000>; - qcom,controller-type = "pmic-arbiter"; - }; - - gcc: clock-controller@900000 { - compatible = "qcom,gcc-ipq8064"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - }; - - tsens: thermal-sensor@900000 { - compatible = "qcom,ipq8064-tsens"; - reg = <0x900000 0x3680>; - nvmem-cells = <&tsens_calib>, <&tsens_backup>; - nvmem-cell-names = "calib", "calib_backup"; - interrupts = <0 178 0>; - #thermal-sensor-cells = <1>; - }; - - tcsr: syscon@1a400000 { - compatible = "qcom,tcsr-ipq8064", "syscon"; - reg = <0x1a400000 0x100>; - }; - - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - sfpb_mutex_block: syscon@1200600 { - compatible = "syscon"; - reg = <0x01200600 0x100>; - }; - - hs_phy_1: phy@100f8800 { - compatible = "qcom,dwc3-hs-usb-phy"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_1_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_1: phy@100f8830 { - compatible = "qcom,dwc3-ss-usb-phy"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - hs_phy_0: phy@110f8800 { - compatible = "qcom,dwc3-hs-usb-phy"; - reg = <0x110f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_0: phy@110f8830 { - compatible = "qcom,dwc3-ss-usb-phy"; - reg = <0x110f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_0: usb30@0 { - compatible = "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_0_MASTER_RESET>; - reset-names = "usb30_0_mstr_rst"; - - status = "disabled"; - - dwc3@11000000 { - compatible = "snps,dwc3"; - reg = <0x11000000 0xcd00>; - interrupts = <0 110 0x4>; - phys = <&hs_phy_0>, <&ss_phy_0>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - usb3_1: usb30@1 { - compatible = "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_1_MASTER_RESET>; - reset-names = "usb30_1_mstr_rst"; - - status = "disabled"; - - dwc3@10000000 { - compatible = "snps,dwc3"; - reg = <0x10000000 0xcd00>; - interrupts = <0 205 0x4>; - phys = <&hs_phy_1>, <&ss_phy_1>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - pcie0: pci@1b500000 { - compatible = "qcom,pcie-ipq8064"; - reg = <0x1b500000 0x1000 - 0x1b502000 0x80 - 0x1b600000 0x100 - 0x0ff00000 0x100000>; - reg-names = "dbi", "elbi", "parf", "config"; - device_type = "pci"; - linux,pci-domain = <0>; - bus-range = <0x00 0xff>; - num-lanes = <1>; - #address-cells = <3>; - #size-cells = <2>; - - ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ - 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ - - interrupts = <GIC_SPI 35 IRQ_TYPE_NONE>; - interrupt-names = "msi"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ - <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ - <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ - <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc PCIE_A_CLK>, - <&gcc PCIE_H_CLK>, - <&gcc PCIE_PHY_CLK>, - <&gcc PCIE_AUX_CLK>, - <&gcc PCIE_ALT_REF_CLK>; - clock-names = "core", "iface", "phy", "aux", "ref"; - - assigned-clocks = <&gcc PCIE_ALT_REF_CLK>; - assigned-clock-rates = <100000000>; - - resets = <&gcc PCIE_ACLK_RESET>, - <&gcc PCIE_HCLK_RESET>, - <&gcc PCIE_POR_RESET>, - <&gcc PCIE_PCI_RESET>, - <&gcc PCIE_PHY_RESET>, - <&gcc PCIE_EXT_RESET>; - reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; - - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - - perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - - phy-tx0-term-offset = <7>; - - status = "disabled"; - }; - - pcie1: pci@1b700000 { - compatible = "qcom,pcie-ipq8064"; - reg = <0x1b700000 0x1000 - 0x1b702000 0x80 - 0x1b800000 0x100 - 0x31f00000 0x100000>; - reg-names = "dbi", "elbi", "parf", "config"; - device_type = "pci"; - linux,pci-domain = <1>; - bus-range = <0x00 0xff>; - num-lanes = <1>; - #address-cells = <3>; - #size-cells = <2>; - - ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ - 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ - - interrupts = <GIC_SPI 57 IRQ_TYPE_NONE>; - interrupt-names = "msi"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ - <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ - <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ - <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc PCIE_1_A_CLK>, - <&gcc PCIE_1_H_CLK>, - <&gcc PCIE_1_PHY_CLK>, - <&gcc PCIE_1_AUX_CLK>, - <&gcc PCIE_1_ALT_REF_CLK>; - clock-names = "core", "iface", "phy", "aux", "ref"; - - assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>; - assigned-clock-rates = <100000000>; - - resets = <&gcc PCIE_1_ACLK_RESET>, - <&gcc PCIE_1_HCLK_RESET>, - <&gcc PCIE_1_POR_RESET>, - <&gcc PCIE_1_PCI_RESET>, - <&gcc PCIE_1_PHY_RESET>, - <&gcc PCIE_1_EXT_RESET>; - reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; - - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - - perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - - phy-tx0-term-offset = <7>; - - status = "disabled"; - }; - - pcie2: pci@1b900000 { - compatible = "qcom,pcie-ipq8064"; - reg = <0x1b900000 0x1000 - 0x1b902000 0x80 - 0x1ba00000 0x100 - 0x35f00000 0x100000>; - reg-names = "dbi", "elbi", "parf", "config"; - device_type = "pci"; - linux,pci-domain = <2>; - bus-range = <0x00 0xff>; - num-lanes = <1>; - #address-cells = <3>; - #size-cells = <2>; - - ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ - 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ - - interrupts = <GIC_SPI 71 IRQ_TYPE_NONE>; - interrupt-names = "msi"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ - <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ - <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ - <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc PCIE_2_A_CLK>, - <&gcc PCIE_2_H_CLK>, - <&gcc PCIE_2_PHY_CLK>, - <&gcc PCIE_2_AUX_CLK>, - <&gcc PCIE_2_ALT_REF_CLK>; - clock-names = "core", "iface", "phy", "aux", "ref"; - - assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>; - assigned-clock-rates = <100000000>; - - resets = <&gcc PCIE_2_ACLK_RESET>, - <&gcc PCIE_2_HCLK_RESET>, - <&gcc PCIE_2_POR_RESET>, - <&gcc PCIE_2_PCI_RESET>, - <&gcc PCIE_2_PHY_RESET>, - <&gcc PCIE_2_EXT_RESET>; - reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; - - pinctrl-0 = <&pcie2_pins>; - pinctrl-names = "default"; - - perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; - - phy-tx0-term-offset = <7>; - - status = "disabled"; - }; - - adm_dma: dma@18300000 { - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = <0 170 0>; - #dma-cells = <1>; - - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; - - resets = <&gcc ADM0_RESET>, - <&gcc ADM0_PBUS_RESET>, - <&gcc ADM0_C0_RESET>, - <&gcc ADM0_C1_RESET>, - <&gcc ADM0_C2_RESET>; - reset-names = "clk", "pbus", "c0", "c1", "c2"; - qcom,ee = <0>; - - status = "disabled"; - }; - - nand@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - nss_common: syscon@03000000 { - compatible = "syscon"; - reg = <0x03000000 0x0000FFFF>; - }; - - qsgmii_csr: syscon@1bb00000 { - compatible = "syscon"; - reg = <0x1bb00000 0x000001FF>; - }; - - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <7>; - snps,rd_osr_lmt = <7>; - snps,blen = <16 0 0 0 0 0 0>; - }; - - gmac0: ethernet@37000000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37000000 0x200000>; - interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE1_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE1_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - gmac1: ethernet@37200000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37200000 0x200000>; - interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE2_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE2_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - gmac2: ethernet@37400000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37400000 0x200000>; - interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE3_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE3_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - gmac3: ethernet@37600000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37600000 0x200000>; - interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE4_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE4_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - /* Temporary fixed regulator */ - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - sdcc1bam:dma@12402000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12402000 0x8000>; - interrupts = <0 98 0>; - clocks = <&gcc SDC1_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - sdcc3bam:dma@12182000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12182000 0x8000>; - interrupts = <0 96 0>; - clocks = <&gcc SDC3_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - amba { - compatible = "arm,amba-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - sdcc1: sdcc@12400000 { - status = "disabled"; - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - reg = <0x12400000 0x2000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - max-frequency = <96000000>; - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; - }; - - sdcc3: sdcc@12180000 { - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - status = "disabled"; - reg = <0x12180000 0x2000>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <192000000>; - #mmc-ddr-1_8v; - sd-uhs-sdr104; - sd-uhs-ddr50; - vqmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; - dma-names = "tx", "rx"; - }; - }; - }; - - sfpb_mutex: sfpb-mutex { - compatible = "qcom,sfpb-mutex"; - syscon = <&sfpb_mutex_block 4 4>; - - #hwlock-cells = <1>; - }; - - smem { - compatible = "qcom,smem"; - memory-region = <&smem>; - hwlocks = <&sfpb_mutex 3>; - }; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts deleted file mode 100644 index 0b96ba64c6..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts +++ /dev/null @@ -1,388 +0,0 @@ -#include "qcom-ipq8065.dtsi" - -#include <dt-bindings/input/input.h> - -/ { - model = "ZyXEL NBG6817"; - compatible = "zyxel,nbg6817", "qcom,ipq8065"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - sdcc1 = &sdcc1; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd"; - linux,stdout-path = "serial0:115200n8"; - append-rootblock = "root=/dev/mmcblk0p"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio53", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio9", "gpio26", "gpio33", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - - clk { - pins = "gpio1"; - input-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - - tx { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; - input-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - - cs { - pins = "gpio20"; - drive-strength = <12>; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio16", "gpio17"; - function = "gpio"; - drive-strength = <12>; - }; - - pwr { - pins = "gpio17"; - bias-pull-down; - output-high; - }; - - ovc { - pins = "gpio16"; - bias-pull-up; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio14", "gpio15"; - function = "gpio"; - drive-strength = <12>; - }; - - pwr { - pins = "gpio14"; - bias-pull-down; - output-high; - }; - - ovc { - pins = "gpio15"; - bias-pull-up; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = <GSBI_PROT_SPI>; - status = "ok"; - - spi4: spi@1a280000 { - status = "ok"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash: m25p80@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <51200000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb30@1 { - status = "ok"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - force_gen1 = <1>; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ - 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ - 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ - 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ - 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ - 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ - 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ - 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ - 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ - 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ - 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ - 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ - 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ - 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - qca,ar8327-initvals = < - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x0000c 0x80 /* PAD6_MODE */ - >; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <0>; - qcom,rgmii_delay = <1>; - qcom,phy_mii_type = <0>; - qcom,emulation = <0>; - qcom,irq = <255>; - mdiobus = <&mdio0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,phy_mii_type = <1>; - qcom,emulation = <0>; - qcom,irq = <258>; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - amba { - sdcc1: sdcc@12400000 { - status = "okay"; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - linux,input-type = <EV_SW>; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - internet { - label = "nbg6817:white:internet"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "nbg6817:white:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi2g { - label = "nbg6817:amber:wifi2g"; - gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>; - }; - - /* wifi2g amber from the manual is missing */ - - wifi5g { - label = "nbg6817:amber:wifi5g"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - /* wifi5g amber from the manual is missing */ - }; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065-r7800.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065-r7800.dts deleted file mode 100644 index fbacc039d6..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065-r7800.dts +++ /dev/null @@ -1,525 +0,0 @@ -#include "qcom-ipq8065.dtsi" - -#include <dt-bindings/input/input.h> - -/ { - model = "Netgear Nighthawk X4S R7800"; - compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - - rsvd@5fe00000 { - reg = <0x5fe00000 0x200000>; - reusable; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - }; - - chosen { - linux,stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - - nand_pins: nand_pins { - mux { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38", "gpio39", - "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - pullups { - pins = "gpio39"; - bias-pull-up; - }; - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - - clk { - pins = "gpio1"; - input-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - - tx { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; - input-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - spi6_pins: spi6_pins { - mux { - pins = "gpio55", "gpio56", "gpio58"; - function = "gsbi6"; - bias-pull-down; - }; - - mosi { - pins = "gpio55"; - drive-strength = <12>; - }; - - miso { - pins = "gpio56"; - drive-strength = <14>; - }; - - cs { - pins = "gpio57"; - drive-strength = <12>; - bias-pull-up; - }; - - clk { - pins = "gpio58"; - drive-strength = <12>; - }; - - reset { - pins = "gpio33"; - drive-strength = <10>; - bias-pull-down; - output-high; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = <GSBI_PROT_I2C_UART>; - status = "ok"; - serial@16340000 { - status = "ok"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "ok"; - }; - - sata@29000000 { - ports-implemented = <0x1>; - status = "ok"; - }; - - phy@100f8800 { /* USB3 port 1 HS phy */ - status = "ok"; - }; - - phy@100f8830 { /* USB3 port 1 SS phy */ - status = "ok"; - }; - - phy@110f8800 { /* USB3 port 0 HS phy */ - status = "ok"; - }; - - phy@110f8830 { /* USB3 port 0 SS phy */ - status = "ok"; - }; - - usb30@0 { - status = "ok"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb30@1 { - status = "ok"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "ok"; - }; - - pcie1: pci@1b700000 { - status = "ok"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "ok"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x1C00000>; - }; - - netgear@3480000 { - label = "netgear"; - reg = <0x3480000 0x4480000>; - read-only; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - - firmware@1480000 { - label = "firmware"; - reg = <0x1480000 0x2000000>; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - - phy0: ethernet-phy@0 { - device_type = "ethernet-phy"; - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ - 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ - 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ - 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ - 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ - 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ - 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ - 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ - 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ - 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ - 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ - 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ - 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ - 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ - >; - qca,ar8327-vlans = < - 0x1 0x5e /* VLAN1 Ports 1/2/3/4/6 */ - 0x2 0x21 /* VLAN2 Ports 0/5 */ - >; - }; - - phy4: ethernet-phy@4 { - device_type = "ethernet-phy"; - reg = <4>; - qca,ar8327-initvals = < - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x0000c 0x80 /* PAD6_MODE */ - >; - }; - }; - - gmac1: ethernet@37200000 { - status = "ok"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <0>; - qcom,rgmii_delay = <1>; - qcom,phy_mii_type = <0>; - qcom,emulation = <0>; - qcom,irq = <255>; - mdiobus = <&mdio0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "ok"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,phy_mii_type = <1>; - qcom,emulation = <0>; - qcom,irq = <258>; - mdiobus = <&mdio0>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RFKILL>; - debounce-interval = <60>; - wakeup-source; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = <KEY_RESTART>; - debounce-interval = <60>; - wakeup-source; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = <KEY_WPS_BUTTON>; - debounce-interval = <60>; - wakeup-source; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - power_white: power_white { - label = "r7800:white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - power_amber: power_amber { - label = "r7800:amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "r7800:white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "r7800:amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - usb1 { - label = "r7800:white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "r7800:white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "r7800:white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - wifi { - label = "r7800:white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "r7800:white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "ok"; -}; diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065.dtsi deleted file mode 100644 index 86de2bd8be..0000000000 --- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8065.dtsi +++ /dev/null @@ -1,78 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -/ { - model = "Qualcomm IPQ8065"; - compatible = "qcom,ipq8065", "qcom,ipq8064"; - - qcom,pvs { - qcom,pvs-format-a; - qcom,speed0-pvs0-bin-v0 = - < 1725000000 1262500 >, - < 1400000000 1175000 >, - < 1000000000 1100000 >, - < 800000000 1050000 >, - < 600000000 1000000 >, - < 384000000 975000 >; - qcom,speed0-pvs1-bin-v0 = - < 1725000000 1225000 >, - < 1400000000 1150000 >, - < 1000000000 1075000 >, - < 800000000 1025000 >, - < 600000000 975000 >, - < 384000000 950000 >; - qcom,speed0-pvs2-bin-v0 = - < 1725000000 1200000 >, - < 1400000000 1125000 >, - < 1000000000 1050000 >, - < 800000000 1000000 >, - < 600000000 950000 >, - < 384000000 925000 >; - qcom,speed0-pvs3-bin-v0 = - < 1725000000 1175000 >, - < 1400000000 1100000 >, - < 1000000000 1025000 >, - < 800000000 975000 >, - < 600000000 925000 >, - < 384000000 900000 >; - qcom,speed0-pvs4-bin-v0 = - < 1725000000 1150000 >, - < 1400000000 1075000 >, - < 1000000000 1000000 >, - < 800000000 950000 >, - < 600000000 900000 >, - < 384000000 875000 >; - qcom,speed0-pvs5-bin-v0 = - < 1725000000 1100000 >, - < 1400000000 1025000 >, - < 1000000000 950000 >, - < 800000000 900000 >, - < 600000000 850000 >, - < 384000000 825000 >; - qcom,speed0-pvs6-bin-v0 = - < 1725000000 1050000 >, - < 1400000000 975000 >, - < 1000000000 900000 >, - < 800000000 850000 >, - < 600000000 800000 >, - < 384000000 775000 >; - }; - - soc: soc { - - rpm@108000 { - - regulators { - - smb208_s2a: s2a { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; - }; - - smb208_s2b: s2b { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; - }; - }; - }; - }; -}; |