diff options
Diffstat (limited to 'target/linux/ipq40xx')
8 files changed, 279 insertions, 1 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index bc2ec58806..03ee053fcc 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -52,6 +52,13 @@ engenius,ens620ext) ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth0" ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth1" ;; +mikrotik,cap-ac) + ucidef_set_led_default "power" "POWER" "blue:power" "1" + ucidef_set_led_default "user" "USER" "green:user" "0" + ucidef_set_led_switch "eth1" "ETH1" "green:eth1" "switch0" "0x20" + ucidef_set_led_switch "eth2" "ETH2" "green:eth2" "switch0" "0x10" + ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy0tpt" + ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy1tpt" mikrotik,hap-ac3) ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1" ucidef_set_led_switch "lan1" "LAN1" "green:lan1" "switch0" "0x10" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 2b908c800f..c39890ecd9 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -50,6 +50,10 @@ ipq40xx_setup_interfaces() openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; + mikrotik,cap-ac) + ucidef_add_switch "switch0" \ + "0t@eth0" "4:lan" "5:wan" + ;; asus,rt-ac42u|\ asus,rt-ac58u|\ mikrotik,hap-ac2|\ @@ -190,6 +194,7 @@ ipq40xx_setup_macs() wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr) lan_mac=$(macaddr_add "$wan_mac" 1) ;; + mikrotik,cap-ac |\ mikrotik,hap-ac2|\ mikrotik,hap-ac3) wan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base) diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches index 4036e5356f..5d39d37c08 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches @@ -18,6 +18,9 @@ cilab,meshpoint-one) compex,wpj428) ucidef_add_gpio_switch "sim_card_select" "SIM card select" "3" "0" ;; +mikrotik,cap-ac) + ucidef_add_gpio_switch "poe_passtrough" "POE passtrough enable" "414" "0" + ;; mikrotik,hap-ac3) ucidef_add_gpio_switch "poe_passtrough" "PoE Passthrough" "452" "0" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index c8b1e12ea3..2c56e53f9c 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -112,6 +112,7 @@ case "$FIRMWARE" in caldata_valid "202f" || caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 2) ;; + mikrotik,cap-ac |\ mikrotik,hap-ac2 |\ mikrotik,hap-ac3) wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data" @@ -190,6 +191,7 @@ case "$FIRMWARE" in caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 3) ;; + mikrotik,cap-ac |\ mikrotik,hap-ac2 |\ mikrotik,hap-ac3 |\ mikrotik,sxtsq-5-ac) diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index b0493e10ba..d0e9b5b020 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -138,6 +138,7 @@ platform_do_upgrade() { CI_KERNPART="part.safe" nand_do_upgrade "$1" ;; + mikrotik,cap-ac|\ mikrotik,hap-ac2|\ mikrotik,lhgg-60ad|\ mikrotik,sxtsq-5-ac) diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cap-ac.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cap-ac.dts new file mode 100644 index 0000000000..1afbf97f39 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cap-ac.dts @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */ + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "MikroTik cAP ac"; + compatible = "mikrotik,cap-ac"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x08000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + led-boot = &led_user; + led-failsafe = &led_user; + led-running = &led_user; + led-upgrade = &led_user; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + qcom,poll_required = <0>; + qcom,num_gmac = <1>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + + mode { + label = "mode"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + linux,code = <KEY_LIGHTS_TOGGLE>; + }; + }; + + leds { + compatible = "gpio-leds"; + + power { + label = "blue:power"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + led_user: user { + label = "green:user"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + wlan2g { + label = "green:wlan2g"; + gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + label = "green:wlan5g"; + gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>; + }; + + eth1 { + label = "green:eth1"; + gpios = <ðphy4 1 GPIO_ACTIVE_HIGH>; + }; + + eth2 { + label = "green:eth2"; + gpios = <ðphy3 1 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <2>; + bias-disable; + }; + pin_cs { + function = "gpio"; + pins = "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Qualcomm"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + compatible = "mikrotik,routerboot-partitions"; + #address-cells = <1>; + #size-cells = <1>; + label = "RouterBoot"; + reg = <0x80000 0x80000>; + read-only; + + hard_config { + read-only; + }; + + dtb_config { + read-only; + }; + + soft_config { + }; + }; + + partition@100000 { + compatible = "mikrotik,minor"; + label = "firmware"; + reg = <0x100000 0xf00000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&mdio { + status = "okay"; +}; + +&gmac0 { + vlan_tag = <0 0x3f>; +}; + +ðphy3 { + gpio-controller; + #gpio-cells = <2>; +}; + +ðphy4 { + gpio-controller; + #gpio-cells = <2>; +}; + +&wifi0 { + status = "okay"; + + qcom,ath10k-calibration-variant = "MikroTik-cAP-ac"; +}; + +&wifi1 { + status = "okay"; + + qcom,ath10k-calibration-variant = "MikroTik-cAP-ac"; +}; diff --git a/target/linux/ipq40xx/image/mikrotik.mk b/target/linux/ipq40xx/image/mikrotik.mk index 2fdaad60ab..037a042848 100644 --- a/target/linux/ipq40xx/image/mikrotik.mk +++ b/target/linux/ipq40xx/image/mikrotik.mk @@ -20,6 +20,15 @@ define Device/mikrotik_nand IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata endef +define Device/mikrotik_cap-ac + $(call Device/mikrotik_nor) + DEVICE_MODEL := cAP ac + SOC := qcom-ipq4018 + DEVICE_PACKAGES := ipq-wifi-mikrotik_cap-ac -kmod-ath10k-ct \ + kmod-ath10k-ct-smallbuffers +endef +TARGET_DEVICES += mikrotik_cap-ac + define Device/mikrotik_hap-ac2 $(call Device/mikrotik_nor) DEVICE_MODEL := hAP ac2 diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index b76b1a30bb..09ea4efddd 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -902,11 +902,72 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -902,11 +902,73 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -31,6 +31,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4018-gl-ap1300.dtb \ + qcom-ipq4018-jalapeno.dtb \ + qcom-ipq4018-meshpoint-one.dtb \ ++ qcom-ipq4018-cap-ac.dtb \ + qcom-ipq4018-hap-ac2.dtb \ + qcom-ipq4018-sxtsq-5-ac.dtb \ + qcom-ipq4018-nbg6617.dtb \ |