diff options
Diffstat (limited to 'target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch')
| -rw-r--r-- | target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch | 108 |
1 files changed, 108 insertions, 0 deletions
diff --git a/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch b/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch new file mode 100644 index 0000000000..00be403299 --- /dev/null +++ b/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch @@ -0,0 +1,108 @@ +From c329e5afb42ff0a88285eb4d8a391a18793e4777 Mon Sep 17 00:00:00 2001 +From: David Bauer <mail@david-bauer.net> +Date: Thu, 15 Apr 2021 03:26:50 +0200 +Subject: [PATCH] net: phy: at803x: select correct page on config init + +The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber +as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit +in the chip configure register. + +The driver assumes the copper side is selected on probe, but this might +not be the case depending which page was last selected by the +bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior. + +Select the copper page when probing to circumvent this. + +Signed-off-by: David Bauer <mail@david-bauer.net> +Signed-off-by: David S. Miller <davem@davemloft.net> +--- + drivers/net/phy/at803x.c | 50 +++++++++++++++++++++++++++++++++++++++- + 1 file changed, 49 insertions(+), 1 deletion(-) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -139,6 +139,9 @@ + #define ATH8035_PHY_ID 0x004dd072 + #define AT8030_PHY_ID_MASK 0xffffffef + ++#define AT803X_PAGE_FIBER 0 ++#define AT803X_PAGE_COPPER 1 ++ + MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver"); + MODULE_AUTHOR("Matus Ujhelyi"); + MODULE_LICENSE("GPL"); +@@ -190,6 +193,35 @@ static int at803x_debug_reg_mask(struct + return phy_write(phydev, AT803X_DEBUG_DATA, val); + } + ++static int at803x_write_page(struct phy_device *phydev, int page) ++{ ++ int mask; ++ int set; ++ ++ if (page == AT803X_PAGE_COPPER) { ++ set = AT803X_BT_BX_REG_SEL; ++ mask = 0; ++ } else { ++ set = 0; ++ mask = AT803X_BT_BX_REG_SEL; ++ } ++ ++ return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set); ++} ++ ++static int at803x_read_page(struct phy_device *phydev) ++{ ++ int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG); ++ ++ if (ccr < 0) ++ return ccr; ++ ++ if (ccr & AT803X_BT_BX_REG_SEL) ++ return AT803X_PAGE_COPPER; ++ ++ return AT803X_PAGE_FIBER; ++} ++ + static int at803x_enable_rx_delay(struct phy_device *phydev) + { + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0, +@@ -508,6 +540,7 @@ static int at803x_probe(struct phy_devic + { + struct device *dev = &phydev->mdio.dev; + struct at803x_priv *priv; ++ int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) +@@ -515,7 +548,20 @@ static int at803x_probe(struct phy_devic + + phydev->priv = priv; + +- return at803x_parse_dt(phydev); ++ ret = at803x_parse_dt(phydev); ++ if (ret) ++ return ret; ++ ++ /* Some bootloaders leave the fiber page selected. ++ * Switch to the copper page, as otherwise we read ++ * the PHY capabilities from the fiber side. ++ */ ++ if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { ++ ret = phy_select_page(phydev, AT803X_PAGE_COPPER); ++ ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret); ++ } ++ ++ return ret; + } + + static void at803x_remove(struct phy_device *phydev) +@@ -1097,6 +1143,8 @@ static struct phy_driver at803x_driver[] + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, ++ .read_page = at803x_read_page, ++ .write_page = at803x_write_page, + /* PHY_GBIT_FEATURES */ + .read_status = at803x_read_status, + .aneg_done = at803x_aneg_done, |