aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch')
-rw-r--r--target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch111
1 files changed, 0 insertions, 111 deletions
diff --git a/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch b/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch
deleted file mode 100644
index 221959c48e..0000000000
--- a/target/linux/brcm63xx/patches-3.0/452-board_V2500V.patch
+++ /dev/null
@@ -1,111 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -850,6 +850,63 @@ static struct board_info __initdata boar
- },
- };
-
-+ static struct board_info __initdata board_V2500V_BB = {
-+ .name = "V2500V_BB",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+ .enet1 = {
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "power:green",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "power:red",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ { .name = "ppp",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "wireless",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 31,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .threshold = 3,
-+ },
-+ },
-+};
-+
- #endif
-
- /*
-@@ -1897,6 +1954,7 @@ static const struct board_info __initdat
- &board_96348_D4PW,
- &board_spw500v,
- &board_96348sv,
-+ &board_V2500V_BB,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -2050,6 +2108,22 @@ void __init board_prom_init(void)
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
- boot_addr = (u8 *)KSEG1ADDR(val);
-+ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+ /* Do an early check of CFE and then select bank 0 */
-+
-+ if (boot_addr == (u8 *)0xbf800000) {
-+ u8 *tmp_boot_addr;
-+ tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+ memcpy(&nvram, tmp_boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+ if (!strcmp(nvram.name, "V2500V_BB")) {
-+ printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+ boot_addr = (u8 *)0xbfc00000; // Bank 0
-+ }
-+ }
-
- /* dump cfe version */
- cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
-@@ -2248,6 +2322,13 @@ int __init board_register_devices(void)
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
-
-+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+ /* Loading from CFE always uses Bank 0 */
-+ if (!strcmp(board.name, "V2500V_BB")) {
-+ printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
-+ val = val + 0x400000; // Select Bank 0 start address
-+ }
-+
- mtd_resources[0].start = val;
- mtd_resources[0].end = 0x1FFFFFFF;
-