diff options
Diffstat (limited to 'target/linux/brcm2708/patches-4.9/031-v4.10-0009-ARM-bcm2835-Add-names-for-the-Raspberry-Pi-GPIO-line.patch')
-rw-r--r-- | target/linux/brcm2708/patches-4.9/031-v4.10-0009-ARM-bcm2835-Add-names-for-the-Raspberry-Pi-GPIO-line.patch | 414 |
1 files changed, 414 insertions, 0 deletions
diff --git a/target/linux/brcm2708/patches-4.9/031-v4.10-0009-ARM-bcm2835-Add-names-for-the-Raspberry-Pi-GPIO-line.patch b/target/linux/brcm2708/patches-4.9/031-v4.10-0009-ARM-bcm2835-Add-names-for-the-Raspberry-Pi-GPIO-line.patch new file mode 100644 index 0000000000..da6c3b624d --- /dev/null +++ b/target/linux/brcm2708/patches-4.9/031-v4.10-0009-ARM-bcm2835-Add-names-for-the-Raspberry-Pi-GPIO-line.patch @@ -0,0 +1,414 @@ +From 731b26a6ac17f24057c559361c6d0cb7cb79baed Mon Sep 17 00:00:00 2001 +From: Linus Walleij <linus.walleij@linaro.org> +Date: Thu, 6 Oct 2016 13:15:02 +0200 +Subject: [PATCH] ARM: bcm2835: Add names for the Raspberry Pi GPIO lines + +The idea is to give useful names to GPIO lines that an implementer +will be using from userspace, e.g. for maker type projects. These are +user-visible using tools/gpio/lsgpio.c + +v2: Major rewrite by anholt: Flatten each GPIO line to a line in the + file for better diffing, prefix all expansion header pins with + "P<number>" or "P5HEADER_P<number>" and drop the mostly-unused + GPIO_GEN<smallnumber> names in favor of GPIO<socgpionumber>, fix + extra '[]' on a couple of lines, fix locations of SD_CARD_DETECT, + CAM_GPIO and STATUS_LED, fix HDMI_HPD polarities, rewrite A+ using + unreleased schematics. + +v3: More changes by anholt: Drop P<number> / P5HEADER<number> + prefixes. I had been skeptical about adding them, and was + convinced to drop them by Gottfried (who probably has more + experience with GPIOs in educational contexts than the rest of + us). Also drop [] brackets for "is pinmuxed", which didn't seem + to clarify, and were ambiguous for things like the SPI_*-labeled + pins which may or may not actually be pinmuxed to SPI. + +v4: Rename B+'s SDA0/SCL0 to match the other boards, despite the + naming on its schematic. + +Signed-off-by: Linus Walleij <linus.walleij@linaro.org> +Signed-off-by: Eric Anholt <eric@anholt.net> +--- + arch/arm/boot/dts/bcm2835-rpi-a-plus.dts | 65 +++++++++++++++++++++++++++++++ + arch/arm/boot/dts/bcm2835-rpi-a.dts | 67 ++++++++++++++++++++++++++++++++ + arch/arm/boot/dts/bcm2835-rpi-b-plus.dts | 66 +++++++++++++++++++++++++++++++ + arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 66 +++++++++++++++++++++++++++++++ + arch/arm/boot/dts/bcm2835-rpi-b.dts | 67 ++++++++++++++++++++++++++++++++ + 5 files changed, 331 insertions(+) + +--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts +@@ -22,6 +22,71 @@ + }; + + &gpio { ++ /* ++ * This is based on the unreleased schematic for the Model A+. ++ * ++ * Legend: ++ * "NC" = not connected (no rail from the SoC) ++ * "FOO" = GPIO line named "FOO" on the schematic ++ * "FOO_N" = GPIO line named "FOO" on schematic, active low ++ */ ++ gpio-line-names = "SDA0", ++ "SCL0", ++ "SDA1", ++ "SCL1", ++ "GPIO_GCLK", ++ "GPIO5", ++ "GPIO6", ++ "SPI_CE1_N", ++ "SPI_CE0_N", ++ "SPI_MISO", ++ "SPI_MOSI", ++ "SPI_SCLK", ++ "GPIO12", ++ "GPIO13", ++ /* Serial port */ ++ "TXD0", ++ "RXD0", ++ "GPIO16", ++ "GPIO17", ++ "GPIO18", ++ "GPIO19", ++ "GPIO20", ++ "GPIO21", ++ "GPIO22", ++ "GPIO23", ++ "GPIO24", ++ "GPIO25", ++ "GPIO26", ++ "GPIO27", ++ "SDA0", ++ "SCL0", ++ "NC", /* GPIO30 */ ++ "NC", /* GPIO31 */ ++ "NC", /* GPIO32 */ ++ "NC", /* GPIO33 */ ++ "NC", /* GPIO34 */ ++ "PWR_LOW_N", /* GPIO35 */ ++ "NC", /* GPIO36 */ ++ "NC", /* GPIO37 */ ++ "NC", /* GPIO38 */ ++ "NC", /* GPIO39 */ ++ "PWM0_OUT", /* GPIO40 */ ++ "CAM_GPIO0", /* GPIO41 */ ++ "NC", /* GPIO42 */ ++ "NC", /* GPIO43 */ ++ "NC", /* GPIO44 */ ++ "PWM1_OUT", /* GPIO45 */ ++ "HDMI_HPD_N", ++ "STATUS_LED", ++ /* Used by SD Card */ ++ "SD_CLK_R", ++ "SD_CMD_R", ++ "SD_DATA0_R", ++ "SD_DATA1_R", ++ "SD_DATA2_R", ++ "SD_DATA3_R"; ++ + pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; + + /* I2S interface */ +--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts +@@ -15,6 +15,73 @@ + }; + + &gpio { ++ /* ++ * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf ++ * RPI00021 sheet 02 ++ * ++ * Legend: ++ * "NC" = not connected (no rail from the SoC) ++ * "FOO" = GPIO line named "FOO" on the schematic ++ * "FOO_N" = GPIO line named "FOO" on schematic, active low ++ */ ++ gpio-line-names = "SDA0", ++ "SCL0", ++ "SDA1", ++ "SCL1", ++ "GPIO_GCLK", ++ "CAM_CLK", ++ "LAN_RUN", ++ "SPI_CE1_N", ++ "SPI_CE0_N", ++ "SPI_MISO", ++ "SPI_MOSI", ++ "SPI_SCLK", ++ "NC", /* GPIO12 */ ++ "NC", /* GPIO13 */ ++ /* Serial port */ ++ "TXD0", ++ "RXD0", ++ "STATUS_LED_N", ++ "GPIO17", ++ "GPIO18", ++ "NC", /* GPIO19 */ ++ "NC", /* GPIO20 */ ++ "GPIO21", ++ "GPIO22", ++ "GPIO23", ++ "GPIO24", ++ "GPIO25", ++ "NC", /* GPIO26 */ ++ "CAM_GPIO", ++ /* Binary number representing build/revision */ ++ "CONFIG0", ++ "CONFIG1", ++ "CONFIG2", ++ "CONFIG3", ++ "NC", /* GPIO32 */ ++ "NC", /* GPIO33 */ ++ "NC", /* GPIO34 */ ++ "NC", /* GPIO35 */ ++ "NC", /* GPIO36 */ ++ "NC", /* GPIO37 */ ++ "NC", /* GPIO38 */ ++ "NC", /* GPIO39 */ ++ "PWM0_OUT", ++ "NC", /* GPIO41 */ ++ "NC", /* GPIO42 */ ++ "NC", /* GPIO43 */ ++ "NC", /* GPIO44 */ ++ "PWM1_OUT", ++ "HDMI_HPD_P", ++ "SD_CARD_DET", ++ /* Used by SD Card */ ++ "SD_CLK_R", ++ "SD_CMD_R", ++ "SD_DATA0_R", ++ "SD_DATA1_R", ++ "SD_DATA2_R", ++ "SD_DATA3_R"; ++ + pinctrl-0 = <&gpioout &alt0 &i2s_alt2>; + + /* I2S interface */ +--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts +@@ -23,6 +23,72 @@ + }; + + &gpio { ++ /* ++ * Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf ++ * RPI-BPLUS sheet 1 ++ * ++ * Legend: ++ * "NC" = not connected (no rail from the SoC) ++ * "FOO" = GPIO line named "FOO" on the schematic ++ * "FOO_N" = GPIO line named "FOO" on schematic, active low ++ */ ++ gpio-line-names = "SDA0", ++ "SCL0", ++ "SDA1", ++ "SCL1", ++ "GPIO_GCLK", ++ "GPIO5", ++ "GPIO6", ++ "SPI_CE1_N", ++ "SPI_CE0_N", ++ "SPI_MISO", ++ "SPI_MOSI", ++ "SPI_SCLK", ++ "GPIO12", ++ "GPIO13", ++ /* Serial port */ ++ "TXD0", ++ "RXD0", ++ "GPIO16", ++ "GPIO17", ++ "GPIO18", ++ "GPIO19", ++ "GPIO20", ++ "GPIO21", ++ "GPIO22", ++ "GPIO23", ++ "GPIO24", ++ "GPIO25", ++ "GPIO26", ++ "GPIO27", ++ "SDA0", ++ "SCL0", ++ "NC", /* GPIO30 */ ++ "LAN_RUN", /* GPIO31 */ ++ "CAM_GPIO1", /* GPIO32 */ ++ "NC", /* GPIO33 */ ++ "NC", /* GPIO34 */ ++ "PWR_LOW_N", /* GPIO35 */ ++ "NC", /* GPIO36 */ ++ "NC", /* GPIO37 */ ++ "NC", /* GPIO38 */ ++ "NC", /* GPIO39 */ ++ "PWM0_OUT", /* GPIO40 */ ++ "CAM_GPIO0", /* GPIO41 */ ++ "NC", /* GPIO42 */ ++ "NC", /* GPIO43 */ ++ "ETHCLK", /* GPIO44 */ ++ "PWM1_OUT", /* GPIO45 */ ++ "HDMI_HPD_N", ++ "STATUS_LED", ++ /* Used by SD Card */ ++ "SD_CLK_R", ++ "SD_CMD_R", ++ "SD_DATA0_R", ++ "SD_DATA1_R", ++ "SD_DATA2_R", ++ "SD_DATA3_R"; ++ + pinctrl-0 = <&gpioout &alt0 &i2s_alt0>; + + /* I2S interface */ +--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts +@@ -16,6 +16,72 @@ + }; + + &gpio { ++ /* ++ * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf ++ * RPI00022 sheet 02 ++ * ++ * Legend: ++ * "NC" = not connected (no rail from the SoC) ++ * "FOO" = GPIO line named "FOO" on the schematic ++ * "FOO_N" = GPIO line named "FOO" on schematic, active low ++ */ ++ gpio-line-names = "SDA0", ++ "SCL0", ++ "SDA1", ++ "SCL1", ++ "GPIO_GCLK", ++ "CAM_CLK", ++ "LAN_RUN", ++ "SPI_CE1_N", ++ "SPI_CE0_N", ++ "SPI_MISO", ++ "SPI_MOSI", ++ "SPI_SCLK", ++ "NC", /* GPIO12 */ ++ "NC", /* GPIO13 */ ++ /* Serial port */ ++ "TXD0", ++ "RXD0", ++ "STATUS_LED_N", ++ "GPIO17", ++ "GPIO18", ++ "NC", /* GPIO19 */ ++ "NC", /* GPIO20 */ ++ "CAM_GPIO", ++ "GPIO22", ++ "GPIO23", ++ "GPIO24", ++ "GPIO25", ++ "NC", /* GPIO26 */ ++ "GPIO27", ++ "GPIO28", ++ "GPIO29", ++ "GPIO30", ++ "GPIO31", ++ "NC", /* GPIO32 */ ++ "NC", /* GPIO33 */ ++ "NC", /* GPIO34 */ ++ "NC", /* GPIO35 */ ++ "NC", /* GPIO36 */ ++ "NC", /* GPIO37 */ ++ "NC", /* GPIO38 */ ++ "NC", /* GPIO39 */ ++ "PWM0_OUT", ++ "NC", /* GPIO41 */ ++ "NC", /* GPIO42 */ ++ "NC", /* GPIO43 */ ++ "NC", /* GPIO44 */ ++ "PWM1_OUT", ++ "HDMI_HPD_P", ++ "SD_CARD_DET", ++ /* Used by SD Card */ ++ "SD_CLK_R", ++ "SD_CMD_R", ++ "SD_DATA0_R", ++ "SD_DATA1_R", ++ "SD_DATA2_R", ++ "SD_DATA3_R"; ++ + pinctrl-0 = <&gpioout &alt0 &i2s_alt2>; + + /* I2S interface */ +--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts +@@ -16,6 +16,73 @@ + }; + + &gpio { ++ /* ++ * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf ++ * RPI00021 sheet 02 ++ * ++ * Legend: ++ * "NC" = not connected (no rail from the SoC) ++ * "FOO" = GPIO line named "FOO" on the schematic ++ * "FOO_N" = GPIO line named "FOO" on schematic, active low ++ */ ++ gpio-line-names = "SDA0", ++ "SCL0", ++ "SDA1", ++ "SCL1", ++ "GPIO_GCLK", ++ "CAM_CLK", ++ "LAN_RUN", ++ "SPI_CE1_N", ++ "SPI_CE0_N", ++ "SPI_MISO", ++ "SPI_MOSI", ++ "SPI_SCLK", ++ "NC", /* GPIO12 */ ++ "NC", /* GPIO13 */ ++ /* Serial port */ ++ "TXD0", ++ "RXD0", ++ "STATUS_LED_N", ++ "GPIO17", ++ "GPIO18", ++ "NC", /* GPIO19 */ ++ "NC", /* GPIO20 */ ++ "GPIO21", ++ "GPIO22", ++ "GPIO23", ++ "GPIO24", ++ "GPIO25", ++ "NC", /* GPIO26 */ ++ "CAM_GPIO", ++ /* Binary number representing build/revision */ ++ "CONFIG0", ++ "CONFIG1", ++ "CONFIG2", ++ "CONFIG3", ++ "NC", /* GPIO32 */ ++ "NC", /* GPIO33 */ ++ "NC", /* GPIO34 */ ++ "NC", /* GPIO35 */ ++ "NC", /* GPIO36 */ ++ "NC", /* GPIO37 */ ++ "NC", /* GPIO38 */ ++ "NC", /* GPIO39 */ ++ "PWM0_OUT", ++ "NC", /* GPIO41 */ ++ "NC", /* GPIO42 */ ++ "NC", /* GPIO43 */ ++ "NC", /* GPIO44 */ ++ "PWM1_OUT", ++ "HDMI_HPD_P", ++ "SD_CARD_DET", ++ /* Used by SD Card */ ++ "SD_CLK_R", ++ "SD_CMD_R", ++ "SD_DATA0_R", ++ "SD_DATA1_R", ++ "SD_DATA2_R", ++ "SD_DATA3_R"; ++ + pinctrl-0 = <&gpioout &alt0>; + }; + |