aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm2708/patches-4.19/950-0291-gpio-ir-change-default-pull-configuration-to-up.patch
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/brcm2708/patches-4.19/950-0291-gpio-ir-change-default-pull-configuration-to-up.patch')
-rw-r--r--target/linux/brcm2708/patches-4.19/950-0291-gpio-ir-change-default-pull-configuration-to-up.patch47
1 files changed, 0 insertions, 47 deletions
diff --git a/target/linux/brcm2708/patches-4.19/950-0291-gpio-ir-change-default-pull-configuration-to-up.patch b/target/linux/brcm2708/patches-4.19/950-0291-gpio-ir-change-default-pull-configuration-to-up.patch
deleted file mode 100644
index d68ea95e58..0000000000
--- a/target/linux/brcm2708/patches-4.19/950-0291-gpio-ir-change-default-pull-configuration-to-up.patch
+++ /dev/null
@@ -1,47 +0,0 @@
-From d1cf5fb57ee5ee4512a93614d67d15af9c8070b2 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias@horus.com>
-Date: Wed, 9 Jan 2019 14:51:01 +0100
-Subject: [PATCH 291/806] gpio-ir: change default pull configuration to up
-
-IR receivers like the TSOP series from Vishay and compatible ones
-have active-low open collector outputs with an internal pull up of
-about 30k (according to the TSOP datasheets).
-
-Activating a pull-down resistor on the GPIO will make it work against
-the pull-up in the IR receiver and brings the idle input voltage down
-to about 1.9V (measured on a RPi3B+ with a TSOP4438). While that's
-usually enough to make the RPi see a high signal it's certainly not
-optimal and may even fail when using an IR receiver with a weaker pull-up.
-
-Switching the default GPIO pull to "up" results in an input voltage
-level of about 3.3V and ensures that an idle state (high signal) will
-be detected if no IR receiver is attached.
-
-Signed-off-by: Matthias Reichl <hias@horus.com>
----
- arch/arm/boot/dts/overlays/README | 2 +-
- arch/arm/boot/dts/overlays/gpio-ir-overlay.dts | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -611,7 +611,7 @@ Load: dtoverlay=gpio-ir,<param>=<val>
- Params: gpio_pin Input pin number. Default is 18.
-
- gpio_pull Desired pull-up/down state (off, down, up)
-- Default is "down".
-+ Default is "up".
-
- rc-map-name Default rc keymap (can also be changed by
- ir-keytable), defaults to "rc-rc6-mce"
---- a/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-@@ -30,7 +30,7 @@
- gpio_ir_pins: gpio_ir_pins@12 {
- brcm,pins = <18>; // pin 18
- brcm,function = <0>; // in
-- brcm,pull = <1>; // down
-+ brcm,pull = <2>; // up
- };
- };
- };