diff options
Diffstat (limited to 'target/linux/bcm27xx/patches-5.4/950-0401-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch')
| -rw-r--r-- | target/linux/bcm27xx/patches-5.4/950-0401-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch | 162 |
1 files changed, 0 insertions, 162 deletions
diff --git a/target/linux/bcm27xx/patches-5.4/950-0401-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch b/target/linux/bcm27xx/patches-5.4/950-0401-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch deleted file mode 100644 index 10c5d23b46..0000000000 --- a/target/linux/bcm27xx/patches-5.4/950-0401-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch +++ /dev/null @@ -1,162 +0,0 @@ -From 3c099a50b3d609206a86896405cfdc8a94cd7aa4 Mon Sep 17 00:00:00 2001 -From: Phil Elwell <phil@raspberrypi.org> -Date: Wed, 29 Jan 2020 11:29:06 +0000 -Subject: [PATCH] ARM: dts: Remove bcm2838-rpi-4-b.dts - -Upstream are not going to use the bcm2838 identifier, so begin the -cleanup by removing the suggested upstream Pi 4 .dts file. - -Signed-off-by: Phil Elwell <phil@raspberrypi.org> ---- - arch/arm/boot/dts/Makefile | 1 - - arch/arm/boot/dts/bcm2838-rpi-4-b.dts | 134 -------------------------- - 2 files changed, 135 deletions(-) - delete mode 100644 arch/arm/boot/dts/bcm2838-rpi-4-b.dts - ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -97,7 +97,6 @@ dtb-$(CONFIG_ARCH_BCM2835) += \ - bcm2837-rpi-3-b.dtb \ - bcm2837-rpi-3-b-plus.dtb \ - bcm2837-rpi-cm3-io3.dtb \ -- bcm2838-rpi-4-b.dtb \ - bcm2835-rpi-zero.dtb \ - bcm2835-rpi-zero-w.dtb - dtb-$(CONFIG_ARCH_BCM_5301X) += \ ---- a/arch/arm/boot/dts/bcm2838-rpi-4-b.dts -+++ /dev/null -@@ -1,134 +0,0 @@ --// SPDX-License-Identifier: GPL-2.0 --/dts-v1/; --#include "bcm2838.dtsi" --#include "bcm2835-rpi.dtsi" --#include "bcm2838-rpi.dtsi" -- --/ { -- compatible = "raspberrypi,4-model-b", "brcm,bcm2711"; -- model = "Raspberry Pi 4 Model B"; -- -- chosen { -- /* 8250 auxiliary UART instead of pl011 */ -- stdout-path = "serial1:115200n8"; -- }; -- -- memory@0 { -- device_type = "memory"; -- reg = <0x0 0x0 0x0>; -- }; -- -- leds { -- act { -- gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; -- }; -- -- pwr { -- label = "PWR"; -- gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; -- }; -- }; -- -- wifi_pwrseq: wifi-pwrseq { -- compatible = "mmc-pwrseq-simple"; -- reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; -- }; -- -- sd_io_1v8_reg: sd_io_1v8_reg { -- status = "okay"; -- compatible = "regulator-gpio"; -- vin-supply = <&vdd_5v0_reg>; -- regulator-name = "vdd-sd-io"; -- regulator-min-microvolt = <1800000>; -- regulator-max-microvolt = <3300000>; -- regulator-boot-on; -- regulator-always-on; -- regulator-settling-time-us = <5000>; -- -- gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; -- states = <1800000 0x1 -- 3300000 0x0>; -- }; --}; -- --&firmware { -- expgpio: gpio { -- compatible = "raspberrypi,firmware-gpio"; -- gpio-controller; -- #gpio-cells = <2>; -- gpio-line-names = "BT_ON", -- "WL_ON", -- "PWR_LED_OFF", -- "GLOBAL_RESET", -- "VDD_SD_IO_SEL", -- "CAM_GPIO", -- "", -- ""; -- status = "okay"; -- }; --}; -- --&pwm1 { -- pinctrl-names = "default"; -- pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; -- status = "okay"; --}; -- --/* SDHCI is used to control the SDIO for wireless */ --&sdhci { -- #address-cells = <1>; -- #size-cells = <0>; -- pinctrl-names = "default"; -- pinctrl-0 = <&emmc_gpio34>; -- status = "okay"; -- bus-width = <4>; -- non-removable; -- mmc-pwrseq = <&wifi_pwrseq>; -- -- brcmf: wifi@1 { -- reg = <1>; -- compatible = "brcm,bcm4329-fmac"; -- }; --}; -- --/* EMMC2 is used to drive the SD card */ --&emmc2 { -- status = "okay"; -- broken-cd; -- vqmmc-supply = <&sd_io_1v8_reg>; --}; -- --&genet { -- phy-handle = <&phy1>; -- phy-mode = "rgmii-rxid"; -- status = "okay"; --}; -- --&genet_mdio { -- phy1: ethernet-phy@1 { -- /* No PHY interrupt */ -- reg = <0x1>; -- led-modes = <0x00 0x08>; /* link/activity link */ -- }; --}; -- --/* uart0 communicates with the BT module */ --&uart0 { -- pinctrl-names = "default"; -- pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; -- uart-has-rtscts; -- status = "okay"; -- -- bluetooth { -- compatible = "brcm,bcm43438-bt"; -- max-speed = <2000000>; -- shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; -- }; --}; -- --/* uart1 is mapped to the pin header */ --&uart1 { -- pinctrl-names = "default"; -- pinctrl-0 = <&uart1_gpio14>; -- status = "okay"; --}; |