diff options
Diffstat (limited to 'target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch')
| -rw-r--r-- | target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch | 66 |
1 files changed, 0 insertions, 66 deletions
diff --git a/target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch b/target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch deleted file mode 100644 index 4291f9fee5..0000000000 --- a/target/linux/bcm27xx/patches-4.19/950-0737-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch +++ /dev/null @@ -1,66 +0,0 @@ -From b4f8b92cdfd8ad2e04cdd3f0a73aa4e95d172fb1 Mon Sep 17 00:00:00 2001 -From: Markus Proeller <markus.proeller@pieye.org> -Date: Thu, 10 Oct 2019 19:12:08 +0200 -Subject: [PATCH] dt-bindings: Add binding for the Infineon IRS1125 - sensor - -Adds a binding for the Infineon IRS1125 time-of-flight depth -sensor. - -Signed-off-by: Markus Proeller <markus.proeller@pieye.org> ---- - .../devicetree/bindings/media/i2c/irs1125.txt | 48 +++++++++++++++++++ - 1 file changed, 48 insertions(+) - create mode 100644 Documentation/devicetree/bindings/media/i2c/irs1125.txt - ---- /dev/null -+++ b/Documentation/devicetree/bindings/media/i2c/irs1125.txt -@@ -0,0 +1,48 @@ -+* Infineon irs1125 time of flight sensor -+ -+The Infineon irs1125 is a time of flight digital image sensor with -+an active array size of 352H x 286V. It is programmable through I2C -+interface. The I2C address defaults to 0x3D, but can be reconfigured -+to address 0x3C or 0x41 via I2C commands. Image data is sent through -+MIPI CSI-2, which is configured as either 1 or 2 data lanes. -+ -+Required Properties: -+- compatible: value should be "infineon,irs1125" for irs1125 sensor -+- reg: I2C bus address of the device -+- clocks: reference to the xclk input clock. -+- pwdn-gpios: reference to the GPIO connected to the reset pin. -+ This is an active low signal to the iirs1125. -+ -+The irs1125 device node should contain one 'port' child node with -+an 'endpoint' subnode. For further reading on port node refer to -+Documentation/devicetree/bindings/media/video-interfaces.txt. -+ -+Endpoint node required properties for CSI-2 connection are: -+- remote-endpoint: a phandle to the bus receiver's endpoint node. -+- clock-lanes: should be set to <0> (clock lane on hardware lane 0) -+- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2 -+ supported) -+ -+Example: -+ sensor@10 { -+ compatible = "infineon,irs1125"; -+ reg = <0x3D>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ clocks = <&irs1125_clk>; -+ pwdn-gpios = <&gpio 5 0>; -+ -+ irs1125_clk: camera-clk { -+ compatible = "fixed-clock"; -+ #clock-cells = <0>; -+ clock-frequency = <26000000>; -+ }; -+ -+ port { -+ sensor_out: endpoint { -+ remote-endpoint = <&csiss_in>; -+ clock-lanes = <0>; -+ data-lanes = <1 2>; -+ }; -+ }; -+ }; |