diff options
Diffstat (limited to 'target/linux/ath79')
| -rw-r--r-- | target/linux/ath79/dts/qca9563_zte_mf286.dts | 256 | ||||
| -rw-r--r-- | target/linux/ath79/image/nand.mk | 14 | ||||
| -rw-r--r-- | target/linux/ath79/nand/base-files/etc/board.d/02_network | 4 | ||||
| -rw-r--r-- | target/linux/ath79/nand/config-default | 2 |
4 files changed, 276 insertions, 0 deletions
diff --git a/target/linux/ath79/dts/qca9563_zte_mf286.dts b/target/linux/ath79/dts/qca9563_zte_mf286.dts new file mode 100644 index 0000000000..c4ebdebd10 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_zte_mf286.dts @@ -0,0 +1,256 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// Copyright (c) 2021 Cezary Jackiewicz +// Copyright (c) 2021, 2022 Lech Perczak +#include "qca956x.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "ZTE MF286"; + compatible = "zte,mf286", "qca,qca9563"; + + aliases { + led-boot = &led_debug; + led-failsafe = &led_debug; + led-running = &led_debug; + led-upgrade = &led_debug; + label-mac-device = ð0; + }; + + leds { + compatible = "gpio-leds"; + + /* Hidden green SMD LED below signal strength LEDs + * Visible through slits underside of the case, + * and slightly through the case below signal state LEDs */ + led_debug: led-0 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_DEBUG; + label = "green:debug"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wifi { + label = "wifi"; + linux,code = <KEY_RFKILL>; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + /* This GPIO is used to reset whole board _including_ the modem */ + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; + active-delay = <3000>; + inactive-delay = <1000>; + }; + + ubi-concat { + compatible = "mtd-concat"; + devices = <&ubiconcat0 &ubiconcat1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x7840000>; + label = "ubi"; + }; + }; + }; +}; + +&gpio { + /* GPIO19 is used as a mask to enable WLAN LED + * in stock firmware, which is controlled directly + * by 5GHz Wi-Fi chip, which currently is inactive + * in OpenWrt */ + led-wlan { + gpio-hog; + gpios = <19 GPIO_ACTIVE_LOW>; + output-high; + line-name = "led:wlan"; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x080000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x080000 0x020000>; + read-only; + }; + }; + }; + + flash@1 { + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fota-flag"; + reg = <0x000000 0x140000>; + read-only; + }; + + caldata: partition@140000 { + label = "caldata"; + reg = <0x140000 0x140000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + cal_caldata_1000: cal@1000 { + reg = <0x1000 0x440>; + }; + + cal_caldata_5000: cal@5000 { + reg = <0x5000 0x844>; + }; + }; + + mac: partition@280000 { + label = "mac"; + reg = <0x280000 0x140000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_mac_0: macaddr@0 { + reg = <0x0 0x6>; + }; + }; + + /* This encompasses stock cfg-param, oops, web partitions, + * which can be overwritten safely */ + ubiconcat0: partition@3c0000 { + label = "ubiconcat0"; + reg = <0x3c0000 0xf40000>; + }; + + /* Kernel MTD size is increased to 4MB from stock 3MB */ + partition@1300000 { + label = "kernel"; + reg = <0x1300000 0x400000>; + }; + + /* This encompasses stock rootfs, data, fota partitions, + * which can be overwritten safely */ + ubiconcat1: partition@1600000 { + label = "ubiconcat1"; + reg = <0x1700000 0x6900000>; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + nvmem-cells = <&macaddr_mac_0>; + nvmem-cell-names = "mac-address"; + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&pcie { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0x0 0 0 0 0>; + + nvmem-cells = <&macaddr_mac_0>, <&cal_caldata_5000>; + nvmem-cell-names = "mac-address", "calibration"; + mac-address-increment = <1>; + }; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&macaddr_mac_0>, <&cal_caldata_1000>; + nvmem-cell-names = "mac-address", "calibration"; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk index 1e1152551b..2d7892db94 100644 --- a/target/linux/ath79/image/nand.mk +++ b/target/linux/ath79/image/nand.mk @@ -305,6 +305,20 @@ define Device/netgear_wndr4500-v3 endef TARGET_DEVICES += netgear_wndr4500-v3 +define Device/zte_mf286 + SOC := qca9563 + DEVICE_VENDOR := ZTE + DEVICE_MODEL := MF286 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct \ + ath10k-firmware-qca988x-ct kmod-usb-net-qmi-wwan kmod-usb-serial-option \ + uqmi + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 4096k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += zte_mf286 + define Device/zyxel_nbg6716 SOC := qca9558 DEVICE_VENDOR := ZyXEL diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network index 76cdab18f8..2c85245bee 100644 --- a/target/linux/ath79/nand/base-files/etc/board.d/02_network +++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network @@ -42,6 +42,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" ;; + zte,mf286) + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "5:lan:1" + ;; zyxel,nbg6716) ucidef_add_switch "switch0" \ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth1" diff --git a/target/linux/ath79/nand/config-default b/target/linux/ath79/nand/config-default index 6d8ff2d576..c04a3d1990 100644 --- a/target/linux/ath79/nand/config-default +++ b/target/linux/ath79/nand/config-default @@ -16,6 +16,8 @@ CONFIG_MTD_UBI_BLOCK=y CONFIG_MTD_UBI_WL_THRESHOLD=4096 # CONFIG_PCI_AR71XX is not set CONFIG_PHY_AR7200_USB=y +CONFIG_POWER_RESET=y +CONFIG_POWER_RESET_GPIO_RESTART=y CONFIG_SGL_ALLOC=y CONFIG_UBIFS_FS=y CONFIG_ZLIB_DEFLATE=y |