aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/at91/patches-4.9/104-ARM-at91-build-dtb-for-sama5d27-SOM1-Ek.patch
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/at91/patches-4.9/104-ARM-at91-build-dtb-for-sama5d27-SOM1-Ek.patch')
-rw-r--r--target/linux/at91/patches-4.9/104-ARM-at91-build-dtb-for-sama5d27-SOM1-Ek.patch893
1 files changed, 0 insertions, 893 deletions
diff --git a/target/linux/at91/patches-4.9/104-ARM-at91-build-dtb-for-sama5d27-SOM1-Ek.patch b/target/linux/at91/patches-4.9/104-ARM-at91-build-dtb-for-sama5d27-SOM1-Ek.patch
deleted file mode 100644
index 20c69f39ed..0000000000
--- a/target/linux/at91/patches-4.9/104-ARM-at91-build-dtb-for-sama5d27-SOM1-Ek.patch
+++ /dev/null
@@ -1,893 +0,0 @@
---- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt
-+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt
-@@ -35,7 +35,12 @@ right representation of the pin.
- Optional properties:
- - GENERIC_PINCONFIG: generic pinconfig options to use, bias-disable,
- bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable,
--input-debounce, output-low, output-high.
-+input-debounce, output-low, output-high, drive-strength.
-+
-+Concerning the drive-strength property, the values accepted are
-+ATMEL_PIO_DRVSTR_LO, ATMEL_PIO_DRVSTR_ME, ATMEL_PIO_DRVSTR_HI. The current
-+depends on VDDIOP. You can find the details in the DC Characteristics table
-+from the datasheet.
-
- Example:
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -49,6 +49,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
- wb45n.dtb
- dtb-$(CONFIG_SOC_SAM_V7) += \
- at91-kizbox2.dtb \
-+ at91-sama5d27_som1_ek.dtb \
- at91-sama5d2_xplained.dtb \
- at91-sama5d3_xplained.dtb \
- sama5d31ek.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
-@@ -0,0 +1,175 @@
-+/*
-+ * at91-sama5d27_som1.dtsi - Device Tree file for SAMA5D27 SoM1 board
-+ *
-+ * Copyright (c) 2017, Microchip Technology Inc.
-+ * 2017 Cristian Birsan <cristian.birsan@microchip.com>
-+ * 2017 Claudiu Beznea <claudiu.beznea@microchip.com>
-+ *
-+ * This file is dual-licensed: you can use it either under the terms
-+ * of the GPL or the X11 license, at your option. Note that this dual
-+ * licensing only applies to this file, and not this project as a
-+ * whole.
-+ *
-+ * a) This file is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of the
-+ * License, or (at your option) any later version.
-+ *
-+ * This file is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * Or, alternatively,
-+ *
-+ * b) Permission is hereby granted, free of charge, to any person
-+ * obtaining a copy of this software and associated documentation
-+ * files (the "Software"), to deal in the Software without
-+ * restriction, including without limitation the rights to use,
-+ * copy, modify, merge, publish, distribute, sublicense, and/or
-+ * sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following
-+ * conditions:
-+ *
-+ * The above copyright notice and this permission notice shall be
-+ * included in all copies or substantial portions of the Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
-+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
-+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
-+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
-+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
-+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
-+ * OTHER DEALINGS IN THE SOFTWARE.
-+ */
-+#include "sama5d2.dtsi"
-+#include "sama5d2-pinfunc.h"
-+
-+/ {
-+ model = "Atmel SAMA5D27 SoM1";
-+ compatible = "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
-+
-+ clocks {
-+ slow_xtal {
-+ clock-frequency = <32768>;
-+ };
-+
-+ main_xtal {
-+ clock-frequency = <24000000>;
-+ };
-+ };
-+
-+ ahb {
-+ apb {
-+ qspi1: spi@f0024000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_qspi1_default>;
-+
-+ flash@0 {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ compatible = "jedec,spi-nor";
-+ reg = <0>;
-+ spi-max-frequency = <80000000>;
-+ m25p,fast-read;
-+
-+ at91bootstrap@00000000 {
-+ label = "at91bootstrap";
-+ reg = <0x00000000 0x00010000>;
-+ };
-+
-+ bootloader@00010000 {
-+ label = "bootloader";
-+ reg = <0x00010000 0x000a0000>;
-+ };
-+
-+ bootloaderenv@000b0000 {
-+ label = "bootloader env";
-+ reg = <0x000b0000 0x00010000>;
-+ };
-+
-+ dtb@000c0000 {
-+ label = "device tree";
-+ reg = <0x000c0000 0x0020000>;
-+ };
-+
-+ kernel@000e0000 {
-+ label = "kernel";
-+ reg = <0x000e0000 0x0400000>;
-+ };
-+ };
-+ };
-+
-+ macb0: ethernet@f8008000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_macb0_default>;
-+ phy-mode = "rmii";
-+
-+ ethernet-phy@0 {
-+ reg = <0x0>;
-+ interrupt-parent = <&pioA>;
-+ interrupts = <PIN_PD31 IRQ_TYPE_LEVEL_LOW>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_macb0_phy_irq>;
-+ };
-+ };
-+
-+ i2c0: i2c@f8028000 {
-+ dmas = <0>, <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_i2c0_default>;
-+ status = "okay";
-+
-+ at24@50 {
-+ compatible = "24c02";
-+ reg = <0x50>;
-+ pagesize = <8>;
-+ };
-+ };
-+
-+ pinctrl@fc038000 {
-+ pinctrl_i2c0_default: i2c0_default {
-+ pinmux = <PIN_PD21__TWD0>,
-+ <PIN_PD22__TWCK0>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_qspi1_default: qspi1_default {
-+ sck_cs {
-+ pinmux = <PIN_PB5__QSPI1_SCK>,
-+ <PIN_PB6__QSPI1_CS>;
-+ bias-disable;
-+ };
-+
-+ data {
-+ pinmux = <PIN_PB7__QSPI1_IO0>,
-+ <PIN_PB8__QSPI1_IO1>,
-+ <PIN_PB9__QSPI1_IO2>,
-+ <PIN_PB10__QSPI1_IO3>;
-+ bias-pull-up;
-+ };
-+ };
-+
-+ pinctrl_macb0_default: macb0_default {
-+ pinmux = <PIN_PD9__GTXCK>,
-+ <PIN_PD10__GTXEN>,
-+ <PIN_PD11__GRXDV>,
-+ <PIN_PD12__GRXER>,
-+ <PIN_PD13__GRX0>,
-+ <PIN_PD14__GRX1>,
-+ <PIN_PD15__GTX0>,
-+ <PIN_PD16__GTX1>,
-+ <PIN_PD17__GMDC>,
-+ <PIN_PD18__GMDIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_macb0_phy_irq: macb0_phy_irq {
-+ pinmux = <PIN_PD31__GPIO>;
-+ bias-disable;
-+ };
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
-@@ -0,0 +1,53 @@
-+/*
-+ * at91-sama5d27_som1_ek.dts - Device Tree file for SAMA5D27-SOM1-EK board
-+ *
-+ * Copyright (c) 2017, Microchip Technology Inc.
-+ * 2016 Nicolas Ferre <nicolas.ferre@atmel.com>
-+ * 2017 Cristian Birsan <cristian.birsan@microchip.com>
-+ * 2017 Claudiu Beznea <claudiu.beznea@microchip.com>
-+ *
-+ * This file is dual-licensed: you can use it either under the terms
-+ * of the GPL or the X11 license, at your option. Note that this dual
-+ * licensing only applies to this file, and not this project as a
-+ * whole.
-+ *
-+ * a) This file is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of the
-+ * License, or (at your option) any later version.
-+ *
-+ * This file is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * Or, alternatively,
-+ *
-+ * b) Permission is hereby granted, free of charge, to any person
-+ * obtaining a copy of this software and associated documentation
-+ * files (the "Software"), to deal in the Software without
-+ * restriction, including without limitation the rights to use,
-+ * copy, modify, merge, publish, distribute, sublicense, and/or
-+ * sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following
-+ * conditions:
-+ *
-+ * The above copyright notice and this permission notice shall be
-+ * included in all copies or substantial portions of the Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
-+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
-+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
-+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
-+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
-+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
-+ * OTHER DEALINGS IN THE SOFTWARE.
-+ */
-+/dts-v1/;
-+#include "at91-sama5d27_som1_ek_common.dtsi"
-+
-+/ {
-+ model = "Atmel SAMA5D27 SOM1 EK";
-+ compatible = "atmel,sama5d27-som1-ek", "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek_common.dtsi
-@@ -0,0 +1,619 @@
-+/*
-+ * at91-sama5d27_som1_ek_common.dtsi - Device Tree file for SAMA5D27-SOM1-EK board
-+ *
-+ * Copyright (c) 2017, Microchip Technology Inc.
-+ * 2016 Nicolas Ferre <nicolas.ferre@atmel.com>
-+ * 2017 Cristian Birsan <cristian.birsan@microchip.com>
-+ * 2017 Claudiu Beznea <claudiu.beznea@microchip.com>
-+ *
-+ * This file is dual-licensed: you can use it either under the terms
-+ * of the GPL or the X11 license, at your option. Note that this dual
-+ * licensing only applies to this file, and not this project as a
-+ * whole.
-+ *
-+ * a) This file is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of the
-+ * License, or (at your option) any later version.
-+ *
-+ * This file is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * Or, alternatively,
-+ *
-+ * b) Permission is hereby granted, free of charge, to any person
-+ * obtaining a copy of this software and associated documentation
-+ * files (the "Software"), to deal in the Software without
-+ * restriction, including without limitation the rights to use,
-+ * copy, modify, merge, publish, distribute, sublicense, and/or
-+ * sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following
-+ * conditions:
-+ *
-+ * The above copyright notice and this permission notice shall be
-+ * included in all copies or substantial portions of the Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
-+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
-+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
-+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
-+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
-+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
-+ * OTHER DEALINGS IN THE SOFTWARE.
-+ */
-+#include "at91-sama5d27_som1.dtsi"
-+#include <dt-bindings/mfd/atmel-flexcom.h>
-+#include <dt-bindings/gpio/gpio.h>
-+#include <dt-bindings/pinctrl/at91.h>
-+
-+/ {
-+ model = "Atmel SAMA5D27 SOM1 EK";
-+ compatible = "atmel,sama5d27-som1-ek", "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
-+
-+ aliases {
-+ serial0 = &uart1; /* DBGU */
-+ serial1 = &uart4; /* mikro BUS 1 */
-+ serial2 = &uart2; /* mikro BUS 2 */
-+ i2c1 = &i2c1;
-+ i2c2 = &i2c2;
-+ };
-+
-+ chosen {
-+ stdout-path = "serial0:115200n8";
-+ };
-+
-+ ahb {
-+ usb0: gadget@00300000 {
-+ atmel,vbus-gpio = <&pioA PIN_PD20 GPIO_ACTIVE_HIGH>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_usba_vbus>;
-+ status = "okay";
-+ };
-+
-+ usb1: ohci@00400000 {
-+ num-ports = <3>;
-+ atmel,vbus-gpio = <0 /* &pioA PIN_PD20 GPIO_ACTIVE_HIGH */
-+ &pioA PIN_PA27 GPIO_ACTIVE_HIGH
-+ 0
-+ >;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_usb_default>;
-+ status = "okay";
-+ };
-+
-+ usb2: ehci@00500000 {
-+ status = "okay";
-+ };
-+
-+ sdmmc0: sdio-host@a0000000 {
-+ bus-width = <8>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
-+ status = "okay";
-+ };
-+
-+ sdmmc1: sdio-host@b0000000 {
-+ bus-width = <4>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_sdmmc1_default>;
-+ status = "okay";
-+ };
-+
-+ apb {
-+ hlcdc: hlcdc@f0000000 {
-+ status = "disabled";
-+
-+ hlcdc-display-controller {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb>;
-+ };
-+
-+ hlcdc_pwm: hlcdc-pwm {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_lcd_pwm>;
-+ };
-+ };
-+
-+ pmc: pmc@f0014000 {
-+ pmc_fast_restart {
-+ compatible = "atmel,sama5d2-pmc-fast-startup";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ atmel,wakeup-rtc-timer;
-+
-+ wkpin: input@0 {
-+ reg = <0>;
-+ };
-+
-+ gmac_wol: input@10 {
-+ reg = <10>;
-+ atmel,wakeup-active-high;
-+ };
-+ };
-+ };
-+
-+ isc: isc@f0008000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
-+ status = "okay";
-+ };
-+
-+ qspi1: spi@f0024000 {
-+ status = "okay";
-+ };
-+
-+ spi0: spi@f8000000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_spi0_default>;
-+ status = "okay";
-+ };
-+
-+ macb0: ethernet@f8008000 {
-+ status = "okay";
-+ };
-+
-+ uart1: serial@f8020000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_uart1_default>;
-+ atmel,use-dma-rx;
-+ atmel,use-dma-tx;
-+ status = "okay";
-+ };
-+
-+ uart2: serial@f8024000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_mikrobus2_uart>;
-+ atmel,use-dma-rx;
-+ atmel,use-dma-tx;
-+ status = "okay";
-+ };
-+
-+ pwm0: pwm@f802c000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_mikrobus1_pwm &pinctrl_mikrobus2_pwm>;
-+ status = "disabled"; /* Conflict with leds. */
-+ };
-+
-+ flx1: flexcom@f8038000 {
-+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
-+ status = "okay";
-+
-+ i2c2: i2c@600 {
-+ compatible = "atmel,sama5d2-i2c";
-+ reg = <0x600 0x200>;
-+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
-+ dmas = <0>, <0>;
-+ dma-names = "tx", "rx";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ clocks = <&flx1_clk>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_mikrobus_i2c>;
-+ atmel,fifo-size = <16>;
-+ status = "okay";
-+ };
-+ };
-+
-+ shdwc@f8048010 {
-+ atmel,shdwc-debouncer = <976>;
-+ atmel,wakeup-rtc-timer;
-+
-+ input@0 {
-+ reg = <0>;
-+ atmel,wakeup-type = "low";
-+ };
-+ };
-+
-+ watchdog@f8048040 {
-+ status = "okay";
-+ };
-+
-+ uart3: serial@fc008000 {
-+ atmel,use-dma-rx;
-+ atmel,use-dma-tx;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_uart3_default>;
-+ status = "disabled"; /* Conflict with isc. */
-+ };
-+
-+ uart4: serial@fc00c000 {
-+ atmel,use-dma-rx;
-+ atmel,use-dma-tx;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_mikrobus1_uart>;
-+ status = "okay";
-+ };
-+
-+ flx3: flexcom@fc014000 {
-+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
-+ status = "disabled";
-+
-+ uart7: serial@200 {
-+ compatible = "atmel,at91sam9260-usart";
-+ reg = <0x200 0x200>;
-+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-+ clocks = <&flx3_clk>;
-+ clock-names = "usart";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_flx3_default>;
-+ atmel,fifo-size = <32>;
-+ status = "disabled"; /* Conflict with isc. */
-+ };
-+
-+ spi2: spi@400 {
-+ compatible = "atmel,at91rm9200-spi";
-+ reg = <0x400 0x200>;
-+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-+ clocks = <&flx3_clk>;
-+ clock-names = "spi_clk";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_flx3_default>;
-+ atmel,fifo-size = <16>;
-+ status = "disabled"; /* Conflict with isc. */
-+ };
-+ };
-+
-+ flx4: flexcom@fc018000 {
-+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
-+ status = "okay";
-+
-+ uart6: serial@200 {
-+ compatible = "atmel,at91sam9260-usart";
-+ reg = <0x200 0x200>;
-+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
-+ clocks = <&flx4_clk>;
-+ clock-names = "usart";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_flx4_default>;
-+ atmel,fifo-size = <32>;
-+ status = "disabled"; /* Conflict with spi3 and i2c3. */
-+ };
-+
-+ spi3: spi@400 {
-+ compatible = "atmel,at91rm9200-spi";
-+ reg = <0x400 0x200>;
-+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
-+ clocks = <&flx4_clk>;
-+ clock-names = "spi_clk";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
-+ atmel,fifo-size = <16>;
-+ status = "okay";
-+ };
-+
-+ i2c3: i2c@600 {
-+ compatible = "atmel,sama5d2-i2c";
-+ reg = <0x600 0x200>;
-+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
-+ dmas = <0>, <0>;
-+ dma-names = "tx", "rx";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ clocks = <&flx4_clk>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_flx4_default>;
-+ atmel,fifo-size = <16>;
-+ status = "disabled"; /* Conflict with uart6 and spi3. */
-+ };
-+ };
-+
-+ i2c1: i2c@fc028000 {
-+ dmas = <0>, <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_i2c1_default>;
-+ status = "okay";
-+ };
-+
-+ pinctrl@fc038000 {
-+
-+ pinctrl_lcd_base: pinctrl_lcd_base {
-+ pinmux = <PIN_PC5__LCDVSYNC>,
-+ <PIN_PC6__LCDHSYNC>,
-+ <PIN_PC8__LCDDEN>,
-+ <PIN_PC7__LCDPCK>;
-+ bias-disable;
-+ drive-strength = <ATMEL_PIO_DRVSTR_ME>;
-+ };
-+
-+ pinctrl_lcd_rgb: pinctrl_lcd_rgb {
-+ pinmux = <PIN_PB11__LCDDAT0>,
-+ <PIN_PB12__LCDDAT1>,
-+ <PIN_PB13__LCDDAT2>,
-+ <PIN_PB14__LCDDAT3>,
-+ <PIN_PB15__LCDDAT4>,
-+ <PIN_PB16__LCDDAT5>,
-+ <PIN_PB17__LCDDAT6>,
-+ <PIN_PB18__LCDDAT7>,
-+ <PIN_PB19__LCDDAT8>,
-+ <PIN_PB20__LCDDAT9>,
-+ <PIN_PB21__LCDDAT10>,
-+ <PIN_PB22__LCDDAT11>,
-+ <PIN_PB23__LCDDAT12>,
-+ <PIN_PB24__LCDDAT13>,
-+ <PIN_PB25__LCDDAT14>,
-+ <PIN_PB26__LCDDAT15>,
-+ <PIN_PB27__LCDDAT16>,
-+ <PIN_PB28__LCDDAT17>,
-+ <PIN_PB29__LCDDAT18>,
-+ <PIN_PB30__LCDDAT19>,
-+ <PIN_PB31__LCDDAT20>,
-+ <PIN_PC0__LCDDAT21>,
-+ <PIN_PC1__LCDDAT22>,
-+ <PIN_PC2__LCDDAT23>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_lcd_pwm: pinctrl_lcd_pwm {
-+ pinmux = <PIN_PC3__LCDPWM>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_can1_default: can1_default {
-+ pinmux = <PIN_PC26__CANTX1>,
-+ <PIN_PC27__CANRX1>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_flx3_default: flx3_default {
-+ pinmux = <PIN_PC20__FLEXCOM3_IO0>,
-+ <PIN_PC19__FLEXCOM3_IO1>,
-+ <PIN_PC18__FLEXCOM3_IO2>,
-+ <PIN_PC21__FLEXCOM3_IO3>,
-+ <PIN_PC22__FLEXCOM3_IO4>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_i2c1_default: i2c1_default {
-+ pinmux = <PIN_PD4__TWD1>,
-+ <PIN_PD5__TWCK1>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_isc_base: isc_base {
-+ pinmux = <PIN_PC21__ISC_PCK>,
-+ <PIN_PC22__ISC_VSYNC>,
-+ <PIN_PC23__ISC_HSYNC>,
-+ <PIN_PC24__ISC_MCK>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_isc_data_8bit: isc_data_8bit {
-+ pinmux = <PIN_PC20__ISC_D11>,
-+ <PIN_PC19__ISC_D10>,
-+ <PIN_PC18__ISC_D9>,
-+ <PIN_PC17__ISC_D8>,
-+ <PIN_PC16__ISC_D7>,
-+ <PIN_PC15__ISC_D6>,
-+ <PIN_PC14__ISC_D5>,
-+ <PIN_PC13__ISC_D4>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_isc_data_9_10: isc_data_9_10 {
-+ pinmux = <PIN_PC12__ISC_D3>,
-+ <PIN_PC11__ISC_D2>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_isc_data_11_12: isc_data_11_12 {
-+ pinmux = <PIN_PC10__ISC_D1>,
-+ <PIN_PC9__ISC_D0>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_key_gpio_default: key_gpio_default {
-+ pinmux = <PIN_PA29__GPIO>;
-+ bias-pull-up;
-+ };
-+
-+ pinctrl_led_gpio_default: led_gpio_default {
-+ pinmux = <PIN_PA10__GPIO>,
-+ <PIN_PB1__GPIO>,
-+ <PIN_PA31__GPIO>;
-+ bias-pull-up;
-+ };
-+
-+ pinctrl_sdmmc0_default: sdmmc0_default {
-+ cmd_data {
-+ pinmux = <PIN_PA1__SDMMC0_CMD>,
-+ <PIN_PA2__SDMMC0_DAT0>,
-+ <PIN_PA3__SDMMC0_DAT1>,
-+ <PIN_PA4__SDMMC0_DAT2>,
-+ <PIN_PA5__SDMMC0_DAT3>,
-+ <PIN_PA6__SDMMC0_DAT4>,
-+ <PIN_PA7__SDMMC0_DAT5>,
-+ <PIN_PA8__SDMMC0_DAT6>,
-+ <PIN_PA9__SDMMC0_DAT7>;
-+ bias-disable;
-+ };
-+
-+ ck_cd_vddsel {
-+ pinmux = <PIN_PA0__SDMMC0_CK>,
-+ <PIN_PA11__SDMMC0_VDDSEL>,
-+ <PIN_PA13__SDMMC0_CD>;
-+ bias-disable;
-+ };
-+ };
-+
-+ pinctrl_sdmmc1_default: sdmmc1_default {
-+ cmd_data {
-+ pinmux = <PIN_PA28__SDMMC1_CMD>,
-+ <PIN_PA18__SDMMC1_DAT0>,
-+ <PIN_PA19__SDMMC1_DAT1>,
-+ <PIN_PA20__SDMMC1_DAT2>,
-+ <PIN_PA21__SDMMC1_DAT3>;
-+ bias-disable;
-+ };
-+
-+ conf-ck_cd {
-+ pinmux = <PIN_PA22__SDMMC1_CK>,
-+ <PIN_PA30__SDMMC1_CD>;
-+ bias-disable;
-+ };
-+ };
-+
-+ pinctrl_spi0_default: spi0_default {
-+ pinmux = <PIN_PA14__SPI0_SPCK>,
-+ <PIN_PA15__SPI0_MOSI>,
-+ <PIN_PA16__SPI0_MISO>,
-+ <PIN_PA17__SPI0_NPCS0>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_uart1_default: uart1_default {
-+ pinmux = <PIN_PD2__URXD1>,
-+ <PIN_PD3__UTXD1>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_uart3_default: uart3_default {
-+ pinmux = <PIN_PC12__URXD3>,
-+ <PIN_PC13__UTXD3>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_usb_default: usb_default {
-+ pinmux = <PIN_PA27__GPIO>,
-+ <PIN_PD19__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_usba_vbus: usba_vbus {
-+ pinmux = <PIN_PD20__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus1_an: mikrobus1_an {
-+ pinmux = <PIN_PD25__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus2_an: mikrobus2_an {
-+ pinmux = <PIN_PD26__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus1_rst: mikrobus1_rst {
-+ pinmux = <PIN_PB2__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus2_rst: mikrobus2_rst {
-+ pinmux = <PIN_PA26__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus1_spi_cs: mikrobus1_spi_cs {
-+ pinmux = <PIN_PD0__FLEXCOM4_IO4>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus2_spi_cs: mikrobus2_spi_cs {
-+ pinmux = <PIN_PC31__FLEXCOM4_IO3>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus_spi: mikrobus_spi {
-+ pinmux = <PIN_PC28__FLEXCOM4_IO0>,
-+ <PIN_PC29__FLEXCOM4_IO1>,
-+ <PIN_PC30__FLEXCOM4_IO2>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus1_pwm: mikrobus1_pwm {
-+ pinmux = <PIN_PB1__PWML1>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus2_pwm: mikrobus2_pwm {
-+ pinmux = <PIN_PA31__PWML0>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus1_int: mikrobus1_int {
-+ pinmux = <PIN_PB0__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus2_int: mikrobus2_int {
-+ pinmux = <PIN_PA25__GPIO>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus1_uart: mikrobus1_uart {
-+ pinmux = <PIN_PB3__URXD4>,
-+ <PIN_PB4__UTXD4>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus2_uart: mikrobus2_uart {
-+ pinmux = <PIN_PD23__URXD2>,
-+ <PIN_PD24__UTXD2>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_mikrobus_i2c: mikrobus1_i2c {
-+ pinmux = <PIN_PA24__FLEXCOM1_IO0>,
-+ <PIN_PA23__FLEXCOM1_IO1>;
-+ bias-disable;
-+ };
-+
-+ pinctrl_flx4_default: flx4_uart_default {
-+ pinmux = <PIN_PC28__FLEXCOM4_IO0>,
-+ <PIN_PC29__FLEXCOM4_IO1>,
-+ <PIN_PC30__FLEXCOM4_IO2>,
-+ <PIN_PC31__FLEXCOM4_IO3>,
-+ <PIN_PD0__FLEXCOM4_IO4>;
-+ bias-disable;
-+ };
-+ };
-+
-+ can1: can@fc050000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_can1_default>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_key_gpio_default>;
-+
-+ pb4 {
-+ label = "USER";
-+ gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
-+ linux,code = <0x104>;
-+ wakeup-source;
-+ };
-+ };
-+
-+ leds {
-+ compatible = "gpio-leds";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_led_gpio_default>;
-+ status = "okay"; /* Conflict with pwm0. */
-+
-+ red {
-+ label = "red";
-+ gpios = <&pioA PIN_PA10 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ green {
-+ label = "green";
-+ gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ blue {
-+ label = "blue";
-+ gpios = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "heartbeat";
-+ };
-+ };
-+};
---- a/include/dt-bindings/pinctrl/at91.h
-+++ b/include/dt-bindings/pinctrl/at91.h
-@@ -37,4 +37,8 @@
- #define AT91_PERIPH_C 3
- #define AT91_PERIPH_D 4
-
-+#define ATMEL_PIO_DRVSTR_LO 1
-+#define ATMEL_PIO_DRVSTR_ME 2
-+#define ATMEL_PIO_DRVSTR_HI 3
-+
- #endif /* __DT_BINDINGS_AT91_PINCTRL_H__ */
generated by cgit v1.2.3 (git 2.25.1) at 2025-02-21 08:53:40 +0000