diff options
Diffstat (limited to 'target/linux/ar71xx/patches-4.4/609-MIPS-ath79-ap136-fixes.patch')
| -rw-r--r-- | target/linux/ar71xx/patches-4.4/609-MIPS-ath79-ap136-fixes.patch | 300 |
1 files changed, 300 insertions, 0 deletions
diff --git a/target/linux/ar71xx/patches-4.4/609-MIPS-ath79-ap136-fixes.patch b/target/linux/ar71xx/patches-4.4/609-MIPS-ath79-ap136-fixes.patch new file mode 100644 index 0000000000..5d9d802eda --- /dev/null +++ b/target/linux/ar71xx/patches-4.4/609-MIPS-ath79-ap136-fixes.patch @@ -0,0 +1,300 @@ +--- a/arch/mips/ath79/mach-ap136.c ++++ b/arch/mips/ath79/mach-ap136.c +@@ -18,23 +18,29 @@ + * + */ + +-#include <linux/pci.h> +-#include <linux/ath9k_platform.h> ++#include <linux/platform_device.h> ++#include <linux/ar8216_platform.h> + +-#include "machtypes.h" ++#include <asm/mach-ath79/ar71xx_regs.h> ++ ++#include "common.h" ++#include "pci.h" ++#include "dev-ap9x-pci.h" + #include "dev-gpio-buttons.h" ++#include "dev-eth.h" + #include "dev-leds-gpio.h" +-#include "dev-spi.h" ++#include "dev-m25p80.h" ++#include "dev-nfc.h" + #include "dev-usb.h" + #include "dev-wmac.h" +-#include "pci.h" ++#include "machtypes.h" + +-#define AP136_GPIO_LED_STATUS_RED 14 +-#define AP136_GPIO_LED_STATUS_GREEN 19 + #define AP136_GPIO_LED_USB 4 +-#define AP136_GPIO_LED_WLAN_2G 13 + #define AP136_GPIO_LED_WLAN_5G 12 ++#define AP136_GPIO_LED_WLAN_2G 13 ++#define AP136_GPIO_LED_STATUS_RED 14 + #define AP136_GPIO_LED_WPS_RED 15 ++#define AP136_GPIO_LED_STATUS_GREEN 19 + #define AP136_GPIO_LED_WPS_GREEN 20 + + #define AP136_GPIO_BTN_WPS 16 +@@ -43,37 +49,39 @@ + #define AP136_KEYS_POLL_INTERVAL 20 /* msecs */ + #define AP136_KEYS_DEBOUNCE_INTERVAL (3 * AP136_KEYS_POLL_INTERVAL) + +-#define AP136_WMAC_CALDATA_OFFSET 0x1000 +-#define AP136_PCIE_CALDATA_OFFSET 0x5000 ++#define AP136_MAC0_OFFSET 0 ++#define AP136_MAC1_OFFSET 6 ++#define AP136_WMAC_CALDATA_OFFSET 0x1000 ++#define AP136_PCIE_CALDATA_OFFSET 0x5000 + + static struct gpio_led ap136_leds_gpio[] __initdata = { + { +- .name = "qca:green:status", ++ .name = "ap136:green:status", + .gpio = AP136_GPIO_LED_STATUS_GREEN, + .active_low = 1, + }, + { +- .name = "qca:red:status", ++ .name = "ap136:red:status", + .gpio = AP136_GPIO_LED_STATUS_RED, + .active_low = 1, + }, + { +- .name = "qca:green:wps", ++ .name = "ap136:green:wps", + .gpio = AP136_GPIO_LED_WPS_GREEN, + .active_low = 1, + }, + { +- .name = "qca:red:wps", ++ .name = "ap136:red:wps", + .gpio = AP136_GPIO_LED_WPS_RED, + .active_low = 1, + }, + { +- .name = "qca:red:wlan-2g", ++ .name = "ap136:red:wlan-2g", + .gpio = AP136_GPIO_LED_WLAN_2G, + .active_low = 1, + }, + { +- .name = "qca:red:usb", ++ .name = "ap136:red:usb", + .gpio = AP136_GPIO_LED_USB, + .active_low = 1, + } +@@ -98,59 +106,151 @@ static struct gpio_keys_button ap136_gpi + }, + }; + +-static struct spi_board_info ap136_spi_info[] = { +- { +- .bus_num = 0, +- .chip_select = 0, +- .max_speed_hz = 25000000, +- .modalias = "mx25l6405d", +- } ++static struct ar8327_pad_cfg ap136_ar8327_pad0_cfg; ++static struct ar8327_pad_cfg ap136_ar8327_pad6_cfg; ++ ++static struct ar8327_platform_data ap136_ar8327_data = { ++ .pad0_cfg = &ap136_ar8327_pad0_cfg, ++ .pad6_cfg = &ap136_ar8327_pad6_cfg, ++ .port0_cfg = { ++ .force_link = 1, ++ .speed = AR8327_PORT_SPEED_1000, ++ .duplex = 1, ++ .txpause = 1, ++ .rxpause = 1, ++ }, ++ .port6_cfg = { ++ .force_link = 1, ++ .speed = AR8327_PORT_SPEED_1000, ++ .duplex = 1, ++ .txpause = 1, ++ .rxpause = 1, ++ }, + }; + +-static struct ath79_spi_platform_data ap136_spi_data = { +- .bus_num = 0, +- .num_chipselect = 1, ++static struct mdio_board_info ap136_mdio0_info[] = { ++ { ++ .bus_id = "ag71xx-mdio.0", ++ .phy_addr = 0, ++ .platform_data = &ap136_ar8327_data, ++ }, + }; + +-#ifdef CONFIG_PCI +-static struct ath9k_platform_data ap136_ath9k_data; ++static void __init ap136_common_setup(void) ++{ ++ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + +-static int ap136_pci_plat_dev_init(struct pci_dev *dev) ++ ath79_register_m25p80(NULL); ++ ++ ath79_register_leds_gpio(-1, ARRAY_SIZE(ap136_leds_gpio), ++ ap136_leds_gpio); ++ ath79_register_gpio_keys_polled(-1, AP136_KEYS_POLL_INTERVAL, ++ ARRAY_SIZE(ap136_gpio_keys), ++ ap136_gpio_keys); ++ ++ ath79_register_usb(); ++ ath79_register_nfc(); ++ ++ ath79_register_wmac(art + AP136_WMAC_CALDATA_OFFSET, NULL); ++ ++ ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN); ++ ++ ath79_register_mdio(0, 0x0); ++ ath79_init_mac(ath79_eth0_data.mac_addr, art + AP136_MAC0_OFFSET, 0); ++ ++ mdiobus_register_board_info(ap136_mdio0_info, ++ ARRAY_SIZE(ap136_mdio0_info)); ++ ++ /* GMAC0 is connected to the RMGII interface */ ++ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII; ++ ath79_eth0_data.phy_mask = BIT(0); ++ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev; ++ ++ ath79_register_eth(0); ++ ++ /* GMAC1 is connected tot eh SGMII interface */ ++ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII; ++ ath79_eth1_data.speed = SPEED_1000; ++ ath79_eth1_data.duplex = DUPLEX_FULL; ++ ++ ath79_register_eth(1); ++} ++ ++static void __init ap136_010_setup(void) + { +- if (dev->bus->number == 1 && (PCI_SLOT(dev->devfn)) == 0) +- dev->dev.platform_data = &ap136_ath9k_data; ++ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + +- return 0; ++ /* GMAC0 of the AR8327 switch is connected to GMAC0 via RGMII */ ++ ap136_ar8327_pad0_cfg.mode = AR8327_PAD_MAC_RGMII; ++ ap136_ar8327_pad0_cfg.txclk_delay_en = true; ++ ap136_ar8327_pad0_cfg.rxclk_delay_en = true; ++ ap136_ar8327_pad0_cfg.txclk_delay_sel = AR8327_CLK_DELAY_SEL1; ++ ap136_ar8327_pad0_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2; ++ ++ /* GMAC6 of the AR8327 switch is connected to GMAC1 via SGMII */ ++ ap136_ar8327_pad6_cfg.mode = AR8327_PAD_MAC_SGMII; ++ ap136_ar8327_pad6_cfg.rxclk_delay_en = true; ++ ap136_ar8327_pad6_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL0; ++ ++ ath79_eth0_pll_data.pll_1000 = 0xa6000000; ++ ath79_eth1_pll_data.pll_1000 = 0x03000101; ++ ++ ap136_common_setup(); ++ ap91_pci_init(art + AP136_PCIE_CALDATA_OFFSET, NULL); + } + +-static void __init ap136_pci_init(u8 *eeprom) ++MIPS_MACHINE(ATH79_MACH_AP136_010, "AP136-010", ++ "Atheros AP136-010 reference board", ++ ap136_010_setup); ++ ++static void __init ap136_020_common_setup(void) + { +- memcpy(ap136_ath9k_data.eeprom_data, eeprom, +- sizeof(ap136_ath9k_data.eeprom_data)); ++ /* GMAC0 of the AR8327 switch is connected to GMAC1 via SGMII */ ++ ap136_ar8327_pad0_cfg.mode = AR8327_PAD_MAC_SGMII; ++ ap136_ar8327_pad0_cfg.sgmii_delay_en = true; + +- ath79_pci_set_plat_dev_init(ap136_pci_plat_dev_init); +- ath79_register_pci(); ++ /* GMAC6 of the AR8327 switch is connected to GMAC0 via RGMII */ ++ ap136_ar8327_pad6_cfg.mode = AR8327_PAD_MAC_RGMII; ++ ap136_ar8327_pad6_cfg.txclk_delay_en = true; ++ ap136_ar8327_pad6_cfg.rxclk_delay_en = true; ++ ap136_ar8327_pad6_cfg.txclk_delay_sel = AR8327_CLK_DELAY_SEL1; ++ ap136_ar8327_pad6_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2; ++ ++ ath79_eth0_pll_data.pll_1000 = 0x56000000; ++ ath79_eth1_pll_data.pll_1000 = 0x03000101; ++ ++ ap136_common_setup(); + } +-#else +-static inline void ap136_pci_init(u8 *eeprom) {} +-#endif /* CONFIG_PCI */ + +-static void __init ap136_setup(void) ++static void __init ap136_020_setup(void) + { + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + +- ath79_register_leds_gpio(-1, ARRAY_SIZE(ap136_leds_gpio), +- ap136_leds_gpio); +- ath79_register_gpio_keys_polled(-1, AP136_KEYS_POLL_INTERVAL, +- ARRAY_SIZE(ap136_gpio_keys), +- ap136_gpio_keys); +- ath79_register_spi(&ap136_spi_data, ap136_spi_info, +- ARRAY_SIZE(ap136_spi_info)); +- ath79_register_usb(); +- ath79_register_wmac(art + AP136_WMAC_CALDATA_OFFSET); +- ap136_pci_init(art + AP136_PCIE_CALDATA_OFFSET); ++ ap136_020_common_setup(); ++ ap91_pci_init(art + AP136_PCIE_CALDATA_OFFSET, NULL); + } + +-MIPS_MACHINE(ATH79_MACH_AP136_010, "AP136-010", +- "Atheros AP136-010 reference board", +- ap136_setup); ++MIPS_MACHINE(ATH79_MACH_AP136_020, "AP136-020", ++ "Atheros AP136-020 reference board", ++ ap136_020_setup); ++ ++/* ++ * AP135-020 is similar to AP136-020, any future AP135 specific init ++ * code can be added here. ++ */ ++static void __init ap135_020_setup(void) ++{ ++ ap136_leds_gpio[0].name = "ap135:green:status"; ++ ap136_leds_gpio[1].name = "ap135:red:status"; ++ ap136_leds_gpio[2].name = "ap135:green:wps"; ++ ap136_leds_gpio[3].name = "ap135:red:wps"; ++ ap136_leds_gpio[4].name = "ap135:red:wlan-2g"; ++ ap136_leds_gpio[5].name = "ap135:red:usb"; ++ ++ ap136_020_common_setup(); ++ ath79_register_pci(); ++} ++ ++MIPS_MACHINE(ATH79_MACH_AP135_020, "AP135-020", ++ "Atheros AP135-020 reference board", ++ ap135_020_setup); +--- a/arch/mips/ath79/Kconfig ++++ b/arch/mips/ath79/Kconfig +@@ -16,16 +16,17 @@ config ATH79_MACH_AP121 + Atheros AP121 reference board. + + config ATH79_MACH_AP136 +- bool "Atheros AP136 reference board" ++ bool "Atheros AP136/AP135 reference board" + select SOC_QCA955X + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO ++ select ATH79_DEV_NFC + select ATH79_DEV_SPI + select ATH79_DEV_USB + select ATH79_DEV_WMAC + help + Say 'Y' here if you want your kernel to support the +- Atheros AP136 reference board. ++ Atheros AP136 or AP135 reference boards. + + config ATH79_MACH_AP81 + bool "Atheros AP81 reference board" |