diff options
Diffstat (limited to 'package/uboot-ifxmips/files/cpu/mips/danube/asc_serial.c')
| -rw-r--r-- | package/uboot-ifxmips/files/cpu/mips/danube/asc_serial.c | 371 |
1 files changed, 0 insertions, 371 deletions
diff --git a/package/uboot-ifxmips/files/cpu/mips/danube/asc_serial.c b/package/uboot-ifxmips/files/cpu/mips/danube/asc_serial.c deleted file mode 100644 index d95ec3fd2f..0000000000 --- a/package/uboot-ifxmips/files/cpu/mips/danube/asc_serial.c +++ /dev/null @@ -1,371 +0,0 @@ -/* - * (INCA) ASC UART support - */ - -#include <config.h> - -#if defined(CONFIG_PURPLE) || defined(CONFIG_INCA_IP) - -#ifdef CONFIG_PURPLE -#define serial_init asc_serial_init -#define serial_putc asc_serial_putc -#define serial_puts asc_serial_puts -#define serial_getc asc_serial_getc -#define serial_tstc asc_serial_tstc -#define serial_setbrg asc_serial_setbrg -#endif - -#include <common.h> -#include <asm/inca-ip.h> -#include "asc_serial.h" - -#ifdef CONFIG_PURPLE - -#undef ASC_FIFO_PRESENT -#define TOUT_LOOP 100000 - -/* Set base address for second FPI interrupt control register bank */ -#define SFPI_INTCON_BASEADDR 0xBF0F0000 - -/* Register offset from base address */ -#define FBS_ISR 0x00000000 /* Interrupt status register */ -#define FBS_IMR 0x00000008 /* Interrupt mask register */ -#define FBS_IDIS 0x00000010 /* Interrupt disable register */ - -/* Interrupt status register bits */ -#define FBS_ISR_AT 0x00000040 /* ASC transmit interrupt */ -#define FBS_ISR_AR 0x00000020 /* ASC receive interrupt */ -#define FBS_ISR_AE 0x00000010 /* ASC error interrupt */ -#define FBS_ISR_AB 0x00000008 /* ASC transmit buffer interrupt */ -#define FBS_ISR_AS 0x00000004 /* ASC start of autobaud detection interrupt */ -#define FBS_ISR_AF 0x00000002 /* ASC end of autobaud detection interrupt */ - -#else - -#define ASC_FIFO_PRESENT - -#endif - - -#define SET_BIT(reg, mask) reg |= (mask) -#define CLEAR_BIT(reg, mask) reg &= (~mask) -#define CLEAR_BITS(reg, mask) CLEAR_BIT(reg, mask) -#define SET_BITS(reg, mask) SET_BIT(reg, mask) -#define SET_BITFIELD(reg, mask, off, val) {reg &= (~mask); reg |= (val << off);} - -extern uint incaip_get_fpiclk(void); - -static int serial_setopt (void); - -/* pointer to ASC register base address */ -static volatile incaAsc_t *pAsc = (incaAsc_t *)INCA_IP_ASC; - -/****************************************************************************** -* -* serial_init - initialize a INCAASC channel -* -* This routine initializes the number of data bits, parity -* and set the selected baud rate. Interrupts are disabled. -* Set the modem control signals if the option is selected. -* -* RETURNS: N/A -*/ - -int serial_init (void) -{ -#ifdef CONFIG_INCA_IP - /* we have to set PMU.EN13 bit to enable an ASC device*/ - INCAASC_PMU_ENABLE(13); -#endif - - /* and we have to set CLC register*/ - CLEAR_BIT(pAsc->asc_clc, ASCCLC_DISS); - SET_BITFIELD(pAsc->asc_clc, ASCCLC_RMCMASK, ASCCLC_RMCOFFSET, 0x0001); - - /* initialy we are in async mode */ - pAsc->asc_con = ASCCON_M_8ASYNC; - - /* select input port */ - pAsc->asc_pisel = (CONSOLE_TTY & 0x1); - -#ifdef ASC_FIFO_PRESENT - /* TXFIFO's filling level */ - SET_BITFIELD(pAsc->asc_txfcon, ASCTXFCON_TXFITLMASK, - ASCTXFCON_TXFITLOFF, INCAASC_TXFIFO_FL); - /* enable TXFIFO */ - SET_BIT(pAsc->asc_txfcon, ASCTXFCON_TXFEN); - - /* RXFIFO's filling level */ - SET_BITFIELD(pAsc->asc_txfcon, ASCRXFCON_RXFITLMASK, - ASCRXFCON_RXFITLOFF, INCAASC_RXFIFO_FL); - /* enable RXFIFO */ - SET_BIT(pAsc->asc_rxfcon, ASCRXFCON_RXFEN); -#endif - - /* enable error signals */ - SET_BIT(pAsc->asc_con, ASCCON_FEN); - SET_BIT(pAsc->asc_con, ASCCON_OEN); - -#ifdef CONFIG_INCA_IP - /* acknowledge ASC interrupts */ - ASC_INTERRUPTS_CLEAR(INCAASC_IRQ_LINE_ALL); - - /* disable ASC interrupts */ - ASC_INTERRUPTS_DISABLE(INCAASC_IRQ_LINE_ALL); -#endif - -#ifdef ASC_FIFO_PRESENT - /* set FIFOs into the transparent mode */ - SET_BIT(pAsc->asc_txfcon, ASCTXFCON_TXTMEN); - SET_BIT(pAsc->asc_rxfcon, ASCRXFCON_RXTMEN); -#endif - - /* set baud rate */ - serial_setbrg(); - - /* set the options */ - serial_setopt(); - - return 0; -} - -void serial_setbrg (void) -{ - ulong uiReloadValue, fdv; - ulong f_ASC; - -#ifdef CONFIG_INCA_IP - f_ASC = incaip_get_fpiclk(); -#else - f_ASC = ASC_CLOCK_RATE; -#endif - -#ifndef INCAASC_USE_FDV - fdv = 2; - uiReloadValue = (f_ASC / (fdv * 16 * CONFIG_BAUDRATE)) - 1; -#else - fdv = INCAASC_FDV_HIGH_BAUDRATE; - uiReloadValue = (f_ASC / (8192 * CONFIG_BAUDRATE / fdv)) - 1; -#endif /* INCAASC_USE_FDV */ - - if ( (uiReloadValue < 0) || (uiReloadValue > 8191) ) - { -#ifndef INCAASC_USE_FDV - fdv = 3; - uiReloadValue = (f_ASC / (fdv * 16 * CONFIG_BAUDRATE)) - 1; -#else - fdv = INCAASC_FDV_LOW_BAUDRATE; - uiReloadValue = (f_ASC / (8192 * CONFIG_BAUDRATE / fdv)) - 1; -#endif /* INCAASC_USE_FDV */ - - if ( (uiReloadValue < 0) || (uiReloadValue > 8191) ) - { - return; /* can't impossibly generate that baud rate */ - } - } - - /* Disable Baud Rate Generator; BG should only be written when R=0 */ - CLEAR_BIT(pAsc->asc_con, ASCCON_R); - -#ifndef INCAASC_USE_FDV - /* - * Disable Fractional Divider (FDE) - * Divide clock by reload-value + constant (BRS) - */ - /* FDE = 0 */ - CLEAR_BIT(pAsc->asc_con, ASCCON_FDE); - - if ( fdv == 2 ) - CLEAR_BIT(pAsc->asc_con, ASCCON_BRS); /* BRS = 0 */ - else - SET_BIT(pAsc->asc_con, ASCCON_BRS); /* BRS = 1 */ - -#else /* INCAASC_USE_FDV */ - - /* Enable Fractional Divider */ - SET_BIT(pAsc->asc_con, ASCCON_FDE); /* FDE = 1 */ - - /* Set fractional divider value */ - pAsc->asc_fdv = fdv & ASCFDV_VALUE_MASK; - -#endif /* INCAASC_USE_FDV */ - - /* Set reload value in BG */ - pAsc->asc_bg = uiReloadValue; - - /* Enable Baud Rate Generator */ - SET_BIT(pAsc->asc_con, ASCCON_R); /* R = 1 */ -} - -/******************************************************************************* -* -* serial_setopt - set the serial options -* -* Set the channel operating mode to that specified. Following options -* are supported: CREAD, CSIZE, PARENB, and PARODD. -* -* Note, this routine disables the transmitter. The calling routine -* may have to re-enable it. -* -* RETURNS: -* Returns 0 to indicate success, otherwise -1 is returned -*/ - -static int serial_setopt (void) -{ - ulong con; - - switch ( ASC_OPTIONS & ASCOPT_CSIZE ) - { - /* 7-bit-data */ - case ASCOPT_CS7: - con = ASCCON_M_7ASYNCPAR; /* 7-bit-data and parity bit */ - break; - - /* 8-bit-data */ - case ASCOPT_CS8: - if ( ASC_OPTIONS & ASCOPT_PARENB ) - con = ASCCON_M_8ASYNCPAR; /* 8-bit-data and parity bit */ - else - con = ASCCON_M_8ASYNC; /* 8-bit-data no parity */ - break; - - /* - * only 7 and 8-bit frames are supported - * if we don't use IOCTL extensions - */ - default: - return -1; - } - - if ( ASC_OPTIONS & ASCOPT_STOPB ) - SET_BIT(con, ASCCON_STP); /* 2 stop bits */ - else - CLEAR_BIT(con, ASCCON_STP); /* 1 stop bit */ - - if ( ASC_OPTIONS & ASCOPT_PARENB ) - SET_BIT(con, ASCCON_PEN); /* enable parity checking */ - else - CLEAR_BIT(con, ASCCON_PEN); /* disable parity checking */ - - if ( ASC_OPTIONS & ASCOPT_PARODD ) - SET_BIT(con, ASCCON_ODD); /* odd parity */ - else - CLEAR_BIT(con, ASCCON_ODD); /* even parity */ - - if ( ASC_OPTIONS & ASCOPT_CREAD ) - SET_BIT(pAsc->asc_whbcon, ASCWHBCON_SETREN); /* Receiver enable */ - - pAsc->asc_con |= con; - - return 0; -} - -void serial_putc (const char c) -{ -#ifdef ASC_FIFO_PRESENT - uint txFl = 0; -#else - uint timeout = 0; -#endif - - if (c == '\n') serial_putc ('\r'); - -#ifdef ASC_FIFO_PRESENT - /* check do we have a free space in the TX FIFO */ - /* get current filling level */ - do - { - txFl = ( pAsc->asc_fstat & ASCFSTAT_TXFFLMASK ) >> ASCFSTAT_TXFFLOFF; - } - while ( txFl == INCAASC_TXFIFO_FULL ); -#else - - while(!(*(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) & - FBS_ISR_AB)) - { - if (timeout++ > TOUT_LOOP) - { - break; - } - } -#endif - - pAsc->asc_tbuf = c; /* write char to Transmit Buffer Register */ - -#ifndef ASC_FIFO_PRESENT - *(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) = FBS_ISR_AB | - FBS_ISR_AT; -#endif - - /* check for errors */ - if ( pAsc->asc_con & ASCCON_OE ) - { - SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLROE); - return; - } -} - -void serial_puts (const char *s) -{ - while (*s) - { - serial_putc (*s++); - } -} - -int serial_getc (void) -{ - ulong symbol_mask; - char c; - - while (!serial_tstc()); - - symbol_mask = - ((ASC_OPTIONS & ASCOPT_CSIZE) == ASCOPT_CS7) ? (0x7f) : (0xff); - - c = (char)(pAsc->asc_rbuf & symbol_mask); - -#ifndef ASC_FIFO_PRESENT - *(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) = FBS_ISR_AR; -#endif - - return c; -} - -int serial_tstc (void) -{ - int res = 1; - -#ifdef ASC_FIFO_PRESENT - if ( (pAsc->asc_fstat & ASCFSTAT_RXFFLMASK) == 0 ) - { - res = 0; - } -#else - if (!(*(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) & - FBS_ISR_AR)) - - { - res = 0; - } -#endif - else if ( pAsc->asc_con & ASCCON_FE ) - { - SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLRFE); - res = 0; - } - else if ( pAsc->asc_con & ASCCON_PE ) - { - SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLRPE); - res = 0; - } - else if ( pAsc->asc_con & ASCCON_OE ) - { - SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLROE); - res = 0; - } - - return res; -} -#endif /* CONFIG_PURPLE || CONFIG_INCA_IP */ |