diff options
| -rw-r--r-- | package/firmware/ipq-wifi/Makefile | 5 | ||||
| -rw-r--r-- | package/firmware/ipq-wifi/board-dlink_dap2610.qca4019 | bin | 0 -> 24316 bytes | |||
| -rwxr-xr-x | target/linux/ipq40xx/base-files/etc/board.d/02_network | 5 | ||||
| -rw-r--r-- | target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 8 | ||||
| -rw-r--r-- | target/linux/ipq40xx/config-4.19 | 1 | ||||
| -rw-r--r-- | target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-dap-2610.dts | 241 | ||||
| -rw-r--r-- | target/linux/ipq40xx/image/Makefile | 39 | ||||
| -rw-r--r-- | target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch | 3 |
8 files changed, 299 insertions, 3 deletions
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 161954fa1f..065cda160d 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -14,6 +14,8 @@ endef define Build/Compile endef +# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git +# to generate the board-* files here. # # This is intended to be used on an interim basis until device-specific # board data for new devices is available through the upstream compilation @@ -21,11 +23,11 @@ endef # Please send a mail with your device-specific board files upstream. # You can find instructions and examples on the linux-wireless wiki: # <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles> -# ALLWIFIBOARDS:= \ aruba_ap-303 \ avm_fritzrepeater-1200 \ + dlink_dap2610 \ ezviz_cs-w3-wd1200g-eup \ linksys_ea8300 \ qxwlan_e2600ac @@ -93,6 +95,7 @@ endef $(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303)) $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200)) +$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610)) $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) diff --git a/package/firmware/ipq-wifi/board-dlink_dap2610.qca4019 b/package/firmware/ipq-wifi/board-dlink_dap2610.qca4019 Binary files differnew file mode 100644 index 0000000000..08ed731a4c --- /dev/null +++ b/package/firmware/ipq-wifi/board-dlink_dap2610.qca4019 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 59a2be0fe6..9cfc43f1f9 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -47,6 +47,7 @@ ipq40xx_setup_interfaces() ;; aruba,ap-303|\ avm,fritzrepeater-1200|\ + dlink,dap-2610 |\ engenius,eap1300|\ meraki,mr33|\ netgear,ex6100v2|\ @@ -103,6 +104,10 @@ ipq40xx_setup_macs() cilab,meshpoint-one) label_mac=$(mtd_get_mac_binary "ART" 0x1006) ;; + dlink,dap-2610) + lan_mac=$(mtd_get_mac_ascii bdcfg lanmac) + label_mac=$lan_mac + ;; engenius,ens620ext) wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) lan_mac=$(macaddr_add "$wan_mac" 1) diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 34ea5a5411..22ac6eefc5 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -87,6 +87,10 @@ case "$FIRMWARE" in unielec,u4019-32m) caldata_extract "0:ART" 0x1000 0x2f20 ;; + dlink,dap-2610) + caldata_extract "ART" 0x1000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac) + ;; engenius,ens620ext) caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2) @@ -158,6 +162,10 @@ case "$FIRMWARE" in unielec,u4019-32m) caldata_extract "0:ART" 0x5000 0x2f20 ;; + dlink,dap-2610) + caldata_extract "ART" 0x5000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a) + ;; engenius,ens620ext) caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3) diff --git a/target/linux/ipq40xx/config-4.19 b/target/linux/ipq40xx/config-4.19 index e9c1bcd199..a28497aaec 100644 --- a/target/linux/ipq40xx/config-4.19 +++ b/target/linux/ipq40xx/config-4.19 @@ -305,6 +305,7 @@ CONFIG_MTD_SPI_NAND=y CONFIG_MTD_SPI_NOR=y CONFIG_MTD_SPLIT_FIRMWARE=y CONFIG_MTD_SPLIT_FIT_FW=y +CONFIG_MTD_SPLIT_WRGG_FW=y CONFIG_MTD_UBI=y CONFIG_MTD_UBI_BEB_LIMIT=20 CONFIG_MTD_UBI_BLOCK=y diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-dap-2610.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-dap-2610.dts new file mode 100644 index 0000000000..0fd4318527 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-dap-2610.dts @@ -0,0 +1,241 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "D-Link DAP 2610"; + compatible = "dlink,dap-2610"; + + aliases { + led-boot = &led_red; + led-failsafe = &led_red; + led-running = &led_green; + led-upgrade = &led_red; + }; + + soc { + edma@c080000 { + qcom,num_gmac = <1>; + status = "ok"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + rng@22000 { + status = "ok"; + }; + + crypto@8e3a000 { + status = "ok"; + }; + + watchdog@b017000 { + status = "ok"; + }; + + ess-switch@c000000 { + status = "ok"; + switch_lan_bmp = <0x20>; + switch_wan_bmp = <0x00>; + }; + + ess-psgmii@98000 { + status = "ok"; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_red: red { + label = "dap-2610:red:power"; + gpios = <&tlmm 4 GPIO_ACTIVE_LOW>; + }; + + led_green: green { + label = "dap-2610:green:power"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "ok"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fixed-partitions"; + + partition@0 { + label = "SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + partition@40000 { + label = "MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + partition@60000 { + label = "QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + partition@c0000 { + label = "CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + partition@d0000 { + label = "DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + partition@e0000 { + label = "APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + partition@f0000 { + label = "APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + partition@170000 { + label = "ART"; + reg = <0x170000 0x10000>; + read-only; + }; + partition@180000 { + compatible = "wrg"; + label = "firmware"; + reg = <0x180000 0xdc0000>; + }; + partition@fb0000 { + label = "rgbd"; + reg = <0xfb0000 0x10000>; + read-only; + }; + partition@fc0000 { + label = "bdcfg"; + reg = <0xfc0000 0x10000>; + read-only; + }; + partition@fd0000 { + label = "langpack"; + reg = <0xfd0000 0x20000>; + read-only; + }; + partition@ff0000 { + label = "certificate"; + reg = <0xff0000 0x10000>; + read-only; + }; + partition@f40000 { + label = "captival"; + reg = <0xf40000 0x70000>; + read-only; + }; + }; + }; +}; + +&blsp_dma { + status = "ok"; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "ok"; +}; + +&cryptobam { + status = "ok"; +}; + +&gmac0 { + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <1 0x20>; +}; + +&mdio { + status = "ok"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + mux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + mux_cs { + function = "gpio"; + pins = "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&wifi0 { + status = "ok"; + qcom,ath10k-calibration-variant = "dlink,dap-2610"; +}; + +&wifi1 { + status = "ok"; + qcom,ath10k-calibration-variant = "dlink,dap-2610"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 588a24c2fe..41a65280c3 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -1,7 +1,8 @@ include $(TOPDIR)/rules.mk include $(INCLUDE_DIR)/image.mk -DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION +DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION \ + WRGG_DEVNAME WRGG_SIGNATURE define Device/Default PROFILES := Default @@ -61,6 +62,15 @@ define Build/SenaoFW @cp $@.new $@ endef +define Build/wrgg-image + mkwrggimg -i $@ \ + -o $@.new \ + -d "$(WRGG_DEVNAME)" \ + -s "$(WRGG_SIGNATURE)" \ + -v "" -m "" -B "" + mv $@.new $@ +endef + define Device/8dev_jalapeno-common $(call Device/FitImage) $(call Device/UbiFit) @@ -227,6 +237,33 @@ define Device/compex_wpj428 endef TARGET_DEVICES += compex_wpj428 +define Device/dlink_dap-2610 + $(call Device/FitImageLzma) + DEVICE_VENDOR := D-Link + DEVICE_MODEL := DAP-2610 + SOC := qcom-ipq4018 + DEVICE_DTS_CONFIG := config@ap.dk01.1-c1 + BLOCKSIZE := 64k + WRGG_DEVNAME := /dev/mtdblock/8 + WRGG_SIGNATURE := wapac30_dkbs_dap2610 + IMAGE_SIZE := 14080k + IMAGES := sysupgrade.bin factory.bin + # Bootloader expects a special 160 byte header which is added by + # wrgg-image. + # Factory image size must be larger than 6MB, and size in wrgg header must + # match actual factory image size to be flashable from D-Link http server. + # Bootloader verifies checksum of wrgg image before booting, thus jffs2 + # cannot be part of the wrgg image. This is solved in the factory image by + # having the rootfs at the end of the image (without pad-rootfs). And in + # the sysupgrade image only the kernel is included in the wrgg checksum, + # but this is not flashable from the D-link http server. + # append-rootfs must start on an erase block boundary. + IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | append-metadata + DEVICE_PACKAGES := ipq-wifi-dlink_dap2610 +endef +TARGET_DEVICES += dlink_dap-2610 + define Device/engenius_eap1300 $(call Device/FitImage) DEVICE_VENDOR := EnGenius diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 099a2c7cdb..9c9a31e436 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,12 +10,13 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,40 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,41 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ + qcom-ipq4018-a42.dtb \ + qcom-ipq4018-ap120c-ac.dtb \ ++ qcom-ipq4018-dap-2610.dtb \ + qcom-ipq4018-cs-w3-wd1200g-eup.dtb \ + qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ |