diff options
42 files changed, 3854 insertions, 1 deletions
diff --git a/target/linux/ath79/Makefile b/target/linux/ath79/Makefile index 2a9857bfb1..288f0f5cd5 100644 --- a/target/linux/ath79/Makefile +++ b/target/linux/ath79/Makefile @@ -9,7 +9,6 @@ SUBTARGETS:=generic mikrotik nand tiny FEATURES:=ramdisk squashfs usbgadget KERNEL_PATCHVER:=5.4 -KERNEL_TESTING_PATCHVER:=5.4 include $(INCLUDE_DIR)/target.mk diff --git a/target/linux/ath79/config-5.10 b/target/linux/ath79/config-5.10 new file mode 100644 index 0000000000..4ea93d0837 --- /dev/null +++ b/target/linux/ath79/config-5.10 @@ -0,0 +1,199 @@ +CONFIG_AG71XX=y +# CONFIG_AG71XX_DEBUG is not set +CONFIG_AG71XX_DEBUG_FS=y +CONFIG_AR8216_PHY=y +CONFIG_AR8216_PHY_LEDS=y +CONFIG_ARCH_32BIT_OFF_T=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_MMAP_RND_BITS_MAX=15 +CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=15 +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ATH79=y +CONFIG_ATH79_WDT=y +CONFIG_BLK_MQ_PCI=y +CONFIG_CEVT_R4K=y +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMDLINE="rootfstype=squashfs,jffs2" +CONFIG_CMDLINE_BOOL=y +# CONFIG_CMDLINE_OVERRIDE is not set +CONFIG_COMMON_CLK=y +# CONFIG_COMMON_CLK_BOSTON is not set +CONFIG_COMPAT_32BIT_TIME=y +CONFIG_CPU_BIG_ENDIAN=y +CONFIG_CPU_GENERIC_DUMP_TLB=y +CONFIG_CPU_HAS_DIEI=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_RIXI=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R2=y +CONFIG_CPU_MIPSR2=y +CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y +CONFIG_CPU_R4K_CACHE_TLB=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +CONFIG_CPU_SUPPORTS_MSA=y +# CONFIG_CRYPTO_CHACHA_MIPS is not set +CONFIG_CRYPTO_LIB_POLY1305_RSIZE=2 +# CONFIG_CRYPTO_POLY1305_MIPS is not set +CONFIG_CRYPTO_RNG2=y +CONFIG_CSRC_R4K=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_DTC=y +CONFIG_EARLY_PRINTK=y +CONFIG_FIXED_PHY=y +CONFIG_FW_LOADER_PAGED_BUF=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_GETTIMEOFDAY=y +CONFIG_GENERIC_IOMAP=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_LIB_ASHLDI3=y +CONFIG_GENERIC_LIB_ASHRDI3=y +CONFIG_GENERIC_LIB_CMPDI2=y +CONFIG_GENERIC_LIB_LSHRDI3=y +CONFIG_GENERIC_LIB_UCMPDI2=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_PINCTRL_GROUPS=y +CONFIG_GENERIC_PINMUX_FUNCTIONS=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GPIO_74X164=y +CONFIG_GPIO_ATH79=y +CONFIG_GPIO_GENERIC=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDWARE_WATCHPOINTS=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HZ=250 +CONFIG_HZ_250=y +CONFIG_HZ_PERIODIC=y +CONFIG_IMAGE_CMDLINE_HACK=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_MIPS_CPU=y +CONFIG_IRQ_WORK=y +# CONFIG_KERNEL_ZSTD is not set +CONFIG_LEDS_GPIO=y +# CONFIG_LEDS_RESET is not set +CONFIG_LIBFDT=y +CONFIG_LLD_VERSION=0 +CONFIG_LOCK_DEBUGGING_SUPPORT=y +CONFIG_MDIO_BITBANG=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_GPIO=y +CONFIG_MEMFD_CREATE=y +CONFIG_MFD_SYSCON=y +CONFIG_MIGRATION=y +CONFIG_MIPS=y +CONFIG_MIPS_ASID_BITS=8 +CONFIG_MIPS_ASID_SHIFT=0 +CONFIG_MIPS_CBPF_JIT=y +CONFIG_MIPS_CLOCK_VSYSCALL=y +# CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND is not set +# CONFIG_MIPS_CMDLINE_DTB_EXTEND is not set +# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set +CONFIG_MIPS_CMDLINE_FROM_DTB=y +# CONFIG_MIPS_ELF_APPENDED_DTB is not set +# CONFIG_MIPS_GENERIC_KERNEL is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_MIPS_LD_CAN_LINK_VDSO=y +# CONFIG_MIPS_NO_APPENDED_DTB is not set +CONFIG_MIPS_RAW_APPENDED_DTB=y +CONFIG_MIPS_SPRAM=y +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_CFI_I2 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +CONFIG_MTD_PARSER_CYBERTAN=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_SPI_NOR=y +CONFIG_MTD_SPLIT_ELF_FW=y +CONFIG_MTD_SPLIT_LZMA_FW=y +CONFIG_MTD_SPLIT_SEAMA_FW=y +CONFIG_MTD_SPLIT_TPLINK_FW=y +CONFIG_MTD_SPLIT_UIMAGE_FW=y +CONFIG_MTD_SPLIT_WRGG_FW=y +CONFIG_MTD_VIRT_CONCAT=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y +CONFIG_NVMEM=y +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_PCI=y +CONFIG_PCI_AR71XX=y +CONFIG_PCI_AR724X=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DRIVERS_LEGACY=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +# CONFIG_PHY_AR7100_USB is not set +# CONFIG_PHY_AR7200_USB is not set +# CONFIG_PHY_ATH79_USB is not set +CONFIG_PINCTRL=y +CONFIG_RATIONAL=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_RESET_ATH79=y +CONFIG_RESET_CONTROLLER=y +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=1 +CONFIG_SERIAL_AR933X=y +CONFIG_SERIAL_AR933X_CONSOLE=y +CONFIG_SERIAL_AR933X_NR_UARTS=2 +CONFIG_SERIAL_MCTRL_GPIO=y +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SPI=y +CONFIG_SPI_AR934X=y +CONFIG_SPI_ATH79=y +CONFIG_SPI_BITBANG=y +CONFIG_SPI_GPIO=y +CONFIG_SPI_MASTER=y +CONFIG_SPI_MEM=y +# CONFIG_SPI_RB4XX is not set +CONFIG_SRCU=y +CONFIG_SWCONFIG=y +CONFIG_SWCONFIG_LEDS=y +CONFIG_SWPHY=y +CONFIG_SYSCTL_EXCEPTION_TRACE=y +CONFIG_SYS_HAS_CPU_MIPS32_R2=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_MIPS16=y +CONFIG_SYS_SUPPORTS_ZBOOT=y +CONFIG_SYS_SUPPORTS_ZBOOT_UART_PROM=y +CONFIG_TARGET_ISA_REV=2 +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TINY_SRCU=y +CONFIG_USB_SUPPORT=y +CONFIG_USE_OF=y diff --git a/target/linux/ath79/generic/target.mk b/target/linux/ath79/generic/target.mk index 4e53c89260..2ecaab3f36 100644 --- a/target/linux/ath79/generic/target.mk +++ b/target/linux/ath79/generic/target.mk @@ -2,6 +2,8 @@ BOARDNAME:=Generic DEFAULT_PACKAGES += wpad-basic-wolfssl +KERNEL_TESTING_PATCHVER:=5.10 + define Target/Description Build firmware images for generic Atheros AR71xx/AR913x/AR934x based boards. endef diff --git a/target/linux/ath79/nand/target.mk b/target/linux/ath79/nand/target.mk index 7ea9b57f45..ed3c381093 100644 --- a/target/linux/ath79/nand/target.mk +++ b/target/linux/ath79/nand/target.mk @@ -4,6 +4,8 @@ FEATURES += nand DEFAULT_PACKAGES += wpad-basic-wolfssl +KERNEL_TESTING_PATCHVER:=5.10 + define Target/Description Firmware for boards using Qualcomm Atheros, MIPS-based SoCs in the ar72xx and subsequent series, with support for NAND flash diff --git a/target/linux/ath79/patches-5.10/0003-leds-add-reset-controller-based-driver.patch b/target/linux/ath79/patches-5.10/0003-leds-add-reset-controller-based-driver.patch new file mode 100644 index 0000000000..a023d4c644 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0003-leds-add-reset-controller-based-driver.patch @@ -0,0 +1,186 @@ +From ecbd9c87f073f097d9fe56390353e64e963e866a Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Tue, 6 Mar 2018 10:03:03 +0100 +Subject: [PATCH 03/27] leds: add reset-controller based driver + +Signed-off-by: John Crispin <john@phrozen.org> +--- + drivers/leds/Kconfig | 11 ++++ + drivers/leds/Makefile | 1 + + drivers/leds/leds-reset.c | 137 ++++++++++++++++++++++++++++++++++++++++++++++ + 3 files changed, 149 insertions(+) + create mode 100644 drivers/leds/leds-reset.c + +--- a/drivers/leds/Kconfig ++++ b/drivers/leds/Kconfig +@@ -928,6 +928,17 @@ config LEDS_ACER_A500 + This option enables support for the Power Button LED of + Acer Iconia Tab A500. + ++config LEDS_RESET ++ tristate "LED support for reset-controller API" ++ depends on LEDS_CLASS ++ depends on RESET_CONTROLLER ++ help ++ This option enables support for LEDs connected to pins driven by reset ++ controllers. Yes, DNI actual built HW like that. ++ ++ To compile this driver as a module, choose M here: the module ++ will be called leds-reset. ++ + comment "LED Triggers" + source "drivers/leds/trigger/Kconfig" + +--- /dev/null ++++ b/drivers/leds/leds-reset.c +@@ -0,0 +1,140 @@ ++/* ++ * Copyright (C) 2018 John Crispin <john@phrozen.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++#include <linux/err.h> ++#include <linux/reset.h> ++#include <linux/kernel.h> ++#include <linux/leds.h> ++#include <linux/module.h> ++#include <linux/of.h> ++#include <linux/platform_device.h> ++#include <linux/reset.h> ++ ++struct reset_led_data { ++ struct led_classdev cdev; ++ struct reset_control *rst; ++}; ++ ++static inline struct reset_led_data * ++ cdev_to_reset_led_data(struct led_classdev *led_cdev) ++{ ++ return container_of(led_cdev, struct reset_led_data, cdev); ++} ++ ++static void reset_led_set(struct led_classdev *led_cdev, ++ enum led_brightness value) ++{ ++ struct reset_led_data *led_dat = cdev_to_reset_led_data(led_cdev); ++ ++ if (value == LED_OFF) ++ reset_control_assert(led_dat->rst); ++ else ++ reset_control_deassert(led_dat->rst); ++} ++ ++struct reset_leds_priv { ++ int num_leds; ++ struct reset_led_data leds[]; ++}; ++ ++static inline int sizeof_reset_leds_priv(int num_leds) ++{ ++ return sizeof(struct reset_leds_priv) + ++ (sizeof(struct reset_led_data) * num_leds); ++} ++ ++static struct reset_leds_priv *reset_leds_create(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct fwnode_handle *child; ++ struct reset_leds_priv *priv; ++ int count, ret; ++ ++ count = device_get_child_node_count(dev); ++ if (!count) ++ return ERR_PTR(-ENODEV); ++ ++ priv = devm_kzalloc(dev, sizeof_reset_leds_priv(count), GFP_KERNEL); ++ if (!priv) ++ return ERR_PTR(-ENOMEM); ++ ++ device_for_each_child_node(dev, child) { ++ struct reset_led_data *led = &priv->leds[priv->num_leds]; ++ struct device_node *np = to_of_node(child); ++ ++ ret = fwnode_property_read_string(child, "label", &led->cdev.name); ++ if (!led->cdev.name) { ++ fwnode_handle_put(child); ++ return ERR_PTR(-EINVAL); ++ } ++ led->rst = __of_reset_control_get(np, NULL, 0, 0, 0, true); ++ if (IS_ERR(led->rst)) ++ return ERR_PTR(-EINVAL); ++ ++ fwnode_property_read_string(child, "linux,default-trigger", ++ &led->cdev.default_trigger); ++ ++ led->cdev.brightness_set = reset_led_set; ++ ret = devm_led_classdev_register(&pdev->dev, &led->cdev); ++ if (ret < 0) ++ return ERR_PTR(ret); ++ led->cdev.dev->of_node = np; ++ priv->num_leds++; ++ } ++ ++ return priv; ++} ++ ++static const struct of_device_id of_reset_leds_match[] = { ++ { .compatible = "reset-leds", }, ++ {}, ++}; ++ ++MODULE_DEVICE_TABLE(of, of_reset_leds_match); ++ ++static int reset_led_probe(struct platform_device *pdev) ++{ ++ struct reset_leds_priv *priv; ++ ++ priv = reset_leds_create(pdev); ++ if (IS_ERR(priv)) ++ return PTR_ERR(priv); ++ ++ platform_set_drvdata(pdev, priv); ++ ++ return 0; ++} ++ ++static void reset_led_shutdown(struct platform_device *pdev) ++{ ++ struct reset_leds_priv *priv = platform_get_drvdata(pdev); ++ int i; ++ ++ for (i = 0; i < priv->num_leds; i++) { ++ struct reset_led_data *led = &priv->leds[i]; ++ ++ if (!(led->cdev.flags & LED_RETAIN_AT_SHUTDOWN)) ++ reset_led_set(&led->cdev, LED_OFF); ++ } ++} ++ ++static struct platform_driver reset_led_driver = { ++ .probe = reset_led_probe, ++ .shutdown = reset_led_shutdown, ++ .driver = { ++ .name = "leds-reset", ++ .of_match_table = of_reset_leds_match, ++ }, ++}; ++ ++module_platform_driver(reset_led_driver); ++ ++MODULE_AUTHOR("John Crispin <john@phrozen.org>"); ++MODULE_DESCRIPTION("reset controller LED driver"); ++MODULE_LICENSE("GPL"); ++MODULE_ALIAS("platform:leds-reset"); +--- a/drivers/leds/Makefile ++++ b/drivers/leds/Makefile +@@ -93,6 +93,7 @@ obj-$(CONFIG_LEDS_TURRIS_OMNIA) += leds + obj-$(CONFIG_LEDS_WM831X_STATUS) += leds-wm831x-status.o + obj-$(CONFIG_LEDS_WM8350) += leds-wm8350.o + obj-$(CONFIG_LEDS_WRAP) += leds-wrap.o ++obj-$(CONFIG_LEDS_RESET) += leds-reset.o + + # LED SPI Drivers + obj-$(CONFIG_LEDS_CR0014114) += leds-cr0014114.o diff --git a/target/linux/ath79/patches-5.10/0004-phy-add-ath79-usb-phys.patch b/target/linux/ath79/patches-5.10/0004-phy-add-ath79-usb-phys.patch new file mode 100644 index 0000000000..e319f738a5 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0004-phy-add-ath79-usb-phys.patch @@ -0,0 +1,333 @@ +From 08c9d6ceef01893678a5d2e8a15517c745417f21 Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Tue, 6 Mar 2018 10:04:05 +0100 +Subject: [PATCH 04/27] phy: add ath79 usb phys + +Signed-off-by: John Crispin <john@phrozen.org> +--- + drivers/phy/Kconfig | 16 ++++++ + drivers/phy/Makefile | 2 + + drivers/phy/phy-ar7100-usb.c | 124 +++++++++++++++++++++++++++++++++++++++++++ + drivers/phy/phy-ar7200-usb.c | 108 +++++++++++++++++++++++++++++++++++++ + 4 files changed, 250 insertions(+) + create mode 100644 drivers/phy/phy-ar7100-usb.c + create mode 100644 drivers/phy/phy-ar7200-usb.c + +--- a/drivers/phy/Kconfig ++++ b/drivers/phy/Kconfig +@@ -24,6 +24,22 @@ config GENERIC_PHY_MIPI_DPHY + Provides a number of helpers a core functions for MIPI D-PHY + drivers to us. + ++config PHY_AR7100_USB ++ tristate "Atheros AR7100 USB PHY driver" ++ depends on ATH79 || COMPILE_TEST ++ default y if USB_EHCI_HCD_PLATFORM ++ select PHY_SIMPLE ++ help ++ Enable this to support the USB PHY on Atheros AR7100 SoCs. ++ ++config PHY_AR7200_USB ++ tristate "Atheros AR7200 USB PHY driver" ++ depends on ATH79 || COMPILE_TEST ++ default y if USB_EHCI_HCD_PLATFORM ++ select PHY_SIMPLE ++ help ++ Enable this to support the USB PHY on Atheros AR7200 SoCs. ++ + config PHY_LPC18XX_USB_OTG + tristate "NXP LPC18xx/43xx SoC USB OTG PHY driver" + depends on OF && (ARCH_LPC18XX || COMPILE_TEST) +--- a/drivers/phy/Makefile ++++ b/drivers/phy/Makefile +@@ -4,6 +4,8 @@ + # + + obj-$(CONFIG_GENERIC_PHY) += phy-core.o ++obj-$(CONFIG_PHY_AR7100_USB) += phy-ar7100-usb.o ++obj-$(CONFIG_PHY_AR7200_USB) += phy-ar7200-usb.o + obj-$(CONFIG_GENERIC_PHY_MIPI_DPHY) += phy-core-mipi-dphy.o + obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o + obj-$(CONFIG_PHY_XGENE) += phy-xgene.o +--- /dev/null ++++ b/drivers/phy/phy-ar7100-usb.c +@@ -0,0 +1,140 @@ ++/* ++ * Copyright (C) 2018 John Crispin <john@phrozen.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ */ ++ ++#include <linux/module.h> ++#include <linux/platform_device.h> ++#include <linux/phy/phy.h> ++#include <linux/delay.h> ++#include <linux/reset.h> ++#include <linux/of_gpio.h> ++ ++#include <asm/mach-ath79/ath79.h> ++#include <asm/mach-ath79/ar71xx_regs.h> ++ ++struct ar7100_usb_phy { ++ struct reset_control *rst_phy; ++ struct reset_control *rst_host; ++ struct reset_control *rst_ohci_dll; ++ void __iomem *io_base; ++ struct phy *phy; ++ int gpio; ++}; ++ ++static int ar7100_usb_phy_power_off(struct phy *phy) ++{ ++ struct ar7100_usb_phy *priv = phy_get_drvdata(phy); ++ int err = 0; ++ ++ err |= reset_control_assert(priv->rst_host); ++ err |= reset_control_assert(priv->rst_phy); ++ err |= reset_control_assert(priv->rst_ohci_dll); ++ ++ return err; ++} ++ ++static int ar7100_usb_phy_power_on(struct phy *phy) ++{ ++ struct ar7100_usb_phy *priv = phy_get_drvdata(phy); ++ int err = 0; ++ ++ err |= ar7100_usb_phy_power_off(phy); ++ mdelay(100); ++ err |= reset_control_deassert(priv->rst_ohci_dll); ++ err |= reset_control_deassert(priv->rst_phy); ++ err |= reset_control_deassert(priv->rst_host); ++ mdelay(500); ++ iowrite32(0xf0000, priv->io_base + AR71XX_USB_CTRL_REG_CONFIG); ++ iowrite32(0x20c00, priv->io_base + AR71XX_USB_CTRL_REG_FLADJ); ++ ++ return err; ++} ++ ++static const struct phy_ops ar7100_usb_phy_ops = { ++ .power_on = ar7100_usb_phy_power_on, ++ .power_off = ar7100_usb_phy_power_off, ++ .owner = THIS_MODULE, ++}; ++ ++static int ar7100_usb_phy_probe(struct platform_device *pdev) ++{ ++ struct phy_provider *phy_provider; ++ struct resource *res; ++ struct ar7100_usb_phy *priv; ++ ++ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ priv->io_base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(priv->io_base)) ++ return PTR_ERR(priv->io_base); ++ ++ priv->rst_phy = devm_reset_control_get(&pdev->dev, "usb-phy"); ++ if (IS_ERR(priv->rst_phy)) { ++ dev_err(&pdev->dev, "phy reset is missing\n"); ++ return PTR_ERR(priv->rst_phy); ++ } ++ ++ priv->rst_host = devm_reset_control_get(&pdev->dev, "usb-host"); ++ if (IS_ERR(priv->rst_host)) { ++ dev_err(&pdev->dev, "host reset is missing\n"); ++ return PTR_ERR(priv->rst_host); ++ } ++ ++ priv->rst_ohci_dll = devm_reset_control_get(&pdev->dev, "usb-ohci-dll"); ++ if (IS_ERR(priv->rst_ohci_dll)) { ++ dev_err(&pdev->dev, "ohci-dll reset is missing\n"); ++ return PTR_ERR(priv->rst_host); ++ } ++ ++ priv->phy = devm_phy_create(&pdev->dev, NULL, &ar7100_usb_phy_ops); ++ if (IS_ERR(priv->phy)) { ++ dev_err(&pdev->dev, "failed to create PHY\n"); ++ return PTR_ERR(priv->phy); ++ } ++ ++ priv->gpio = of_get_gpio(pdev->dev.of_node, 0); ++ if (priv->gpio >= 0) { ++ int ret = devm_gpio_request(&pdev->dev, priv->gpio, dev_name(&pdev->dev)); ++ ++ if (ret) { ++ dev_err(&pdev->dev, "failed to request gpio\n"); ++ return ret; ++ } ++ gpio_export_with_name(priv->gpio, 0, dev_name(&pdev->dev)); ++ gpio_set_value(priv->gpio, 1); ++ } ++ ++ phy_set_drvdata(priv->phy, priv); ++ ++ phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); ++ ++ ++ return PTR_ERR_OR_ZERO(phy_provider); ++} ++ ++static const struct of_device_id ar7100_usb_phy_of_match[] = { ++ { .compatible = "qca,ar7100-usb-phy" }, ++ {} ++}; ++MODULE_DEVICE_TABLE(of, ar7100_usb_phy_of_match); ++ ++static struct platform_driver ar7100_usb_phy_driver = { ++ .probe = ar7100_usb_phy_probe, ++ .driver = { ++ .of_match_table = ar7100_usb_phy_of_match, ++ .name = "ar7100-usb-phy", ++ } ++}; ++module_platform_driver(ar7100_usb_phy_driver); ++ ++MODULE_DESCRIPTION("ATH79 USB PHY driver"); ++MODULE_AUTHOR("Alban Bedel <albeu@free.fr>"); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/drivers/phy/phy-ar7200-usb.c +@@ -0,0 +1,136 @@ ++/* ++ * Copyright (C) 2015 Alban Bedel <albeu@free.fr> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ */ ++ ++#include <linux/module.h> ++#include <linux/platform_device.h> ++#include <linux/phy/phy.h> ++#include <linux/reset.h> ++#include <linux/of_gpio.h> ++ ++struct ar7200_usb_phy { ++ struct reset_control *rst_phy; ++ struct reset_control *rst_phy_analog; ++ struct reset_control *suspend_override; ++ struct phy *phy; ++ int gpio; ++}; ++ ++static int ar7200_usb_phy_power_on(struct phy *phy) ++{ ++ struct ar7200_usb_phy *priv = phy_get_drvdata(phy); ++ int err = 0; ++ ++ if (priv->suspend_override) ++ err = reset_control_assert(priv->suspend_override); ++ if (priv->rst_phy) ++ err |= reset_control_deassert(priv->rst_phy); ++ if (priv->rst_phy_analog) ++ err |= reset_control_deassert(priv->rst_phy_analog); ++ ++ return err; ++} ++ ++static int ar7200_usb_phy_power_off(struct phy *phy) ++{ ++ struct ar7200_usb_phy *priv = phy_get_drvdata(phy); ++ int err = 0; ++ ++ if (priv->suspend_override) ++ err = reset_control_deassert(priv->suspend_override); ++ if (priv->rst_phy) ++ err |= reset_control_assert(priv->rst_phy); ++ if (priv->rst_phy_analog) ++ err |= reset_control_assert(priv->rst_phy_analog); ++ ++ return err; ++} ++ ++static const struct phy_ops ar7200_usb_phy_ops = { ++ .power_on = ar7200_usb_phy_power_on, ++ .power_off = ar7200_usb_phy_power_off, ++ .owner = THIS_MODULE, ++}; ++ ++static int ar7200_usb_phy_probe(struct platform_device *pdev) ++{ ++ struct phy_provider *phy_provider; ++ struct ar7200_usb_phy *priv; ++ ++ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ priv->rst_phy = devm_reset_control_get(&pdev->dev, "usb-phy"); ++ if (IS_ERR(priv->rst_phy)) { ++ if (PTR_ERR(priv->rst_phy) != -EPROBE_DEFER) ++ dev_err(&pdev->dev, "phy reset is missing\n"); ++ return PTR_ERR(priv->rst_phy); ++ } ++ ++ priv->rst_phy_analog = devm_reset_control_get_optional( ++ &pdev->dev, "usb-phy-analog"); ++ if (IS_ERR(priv->rst_phy_analog)) { ++ if (PTR_ERR(priv->rst_phy_analog) == -ENOENT) ++ priv->rst_phy_analog = NULL; ++ else ++ return PTR_ERR(priv->rst_phy_analog); ++ } ++ ++ priv->suspend_override = devm_reset_control_get_optional( ++ &pdev->dev, "usb-suspend-override"); ++ if (IS_ERR(priv->suspend_override)) { ++ if (PTR_ERR(priv->suspend_override) == -ENOENT) ++ priv->suspend_override = NULL; ++ else ++ return PTR_ERR(priv->suspend_override); ++ } ++ ++ priv->phy = devm_phy_create(&pdev->dev, NULL, &ar7200_usb_phy_ops); ++ if (IS_ERR(priv->phy)) { ++ dev_err(&pdev->dev, "failed to create PHY\n"); ++ return PTR_ERR(priv->phy); ++ } ++ ++ priv->gpio = of_get_gpio(pdev->dev.of_node, 0); ++ if (priv->gpio >= 0) { ++ int ret = devm_gpio_request(&pdev->dev, priv->gpio, dev_name(&pdev->dev)); ++ ++ if (ret) { ++ dev_err(&pdev->dev, "failed to request gpio\n"); ++ return ret; ++ } ++ gpio_export_with_name(priv->gpio, 0, dev_name(&pdev->dev)); ++ gpio_set_value(priv->gpio, 1); ++ } ++ ++ phy_set_drvdata(priv->phy, priv); ++ ++ phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); ++ ++ return PTR_ERR_OR_ZERO(phy_provider); ++} ++ ++static const struct of_device_id ar7200_usb_phy_of_match[] = { ++ { .compatible = "qca,ar7200-usb-phy" }, ++ {} ++}; ++MODULE_DEVICE_TABLE(of, ar7200_usb_phy_of_match); ++ ++static struct platform_driver ar7200_usb_phy_driver = { ++ .probe = ar7200_usb_phy_probe, ++ .driver = { ++ .of_match_table = ar7200_usb_phy_of_match, ++ .name = "ar7200-usb-phy", ++ } ++}; ++module_platform_driver(ar7200_usb_phy_driver); ++ ++MODULE_DESCRIPTION("ATH79 USB PHY driver"); ++MODULE_AUTHOR("Alban Bedel <albeu@free.fr>"); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/ath79/patches-5.10/0005-usb-add-more-OF-quirk-properties.patch b/target/linux/ath79/patches-5.10/0005-usb-add-more-OF-quirk-properties.patch new file mode 100644 index 0000000000..3c8740311d --- /dev/null +++ b/target/linux/ath79/patches-5.10/0005-usb-add-more-OF-quirk-properties.patch @@ -0,0 +1,24 @@ +From 2201818e5bd33f389beceb3943fdfcf5a698fc5b Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Tue, 6 Mar 2018 10:01:43 +0100 +Subject: [PATCH 05/27] usb: add more OF/quirk properties + +Signed-off-by: John Crispin <john@phrozen.org> +--- + drivers/usb/host/ehci-platform.c | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/drivers/usb/host/ehci-platform.c ++++ b/drivers/usb/host/ehci-platform.c +@@ -269,6 +269,11 @@ static int ehci_platform_probe(struct pl + ehci = hcd_to_ehci(hcd); + + if (pdata == &ehci_platform_defaults && dev->dev.of_node) { ++ of_property_read_u32(dev->dev.of_node, "caps-offset", &pdata->caps_offset); ++ ++ if (of_property_read_bool(dev->dev.of_node, "has-synopsys-hc-bug")) ++ pdata->has_synopsys_hc_bug = 1; ++ + if (of_property_read_bool(dev->dev.of_node, "big-endian-regs")) + ehci->big_endian_mmio = 1; + diff --git a/target/linux/ath79/patches-5.10/0007-irqchip-irq-ath79-intc-add-irq-cascade-driver-for-QC.patch b/target/linux/ath79/patches-5.10/0007-irqchip-irq-ath79-intc-add-irq-cascade-driver-for-QC.patch new file mode 100644 index 0000000000..ceda511c21 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0007-irqchip-irq-ath79-intc-add-irq-cascade-driver-for-QC.patch @@ -0,0 +1,168 @@ +From f3eacff2310a60348a755c50a8da6fc251fc8587 Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Tue, 6 Mar 2018 09:55:13 +0100 +Subject: [PATCH 07/33] irqchip/irq-ath79-intc: add irq cascade driver for + QCA9556 SoCs + +Signed-off-by: John Crispin <john@phrozen.org> +--- + drivers/irqchip/Makefile | 1 + + drivers/irqchip/irq-ath79-intc.c | 142 +++++++++++++++++++++++++++++++++++++++ + 2 files changed, 143 insertions(+) + create mode 100644 drivers/irqchip/irq-ath79-intc.c + +--- a/drivers/irqchip/Makefile ++++ b/drivers/irqchip/Makefile +@@ -4,6 +4,7 @@ obj-$(CONFIG_IRQCHIP) += irqchip.o + obj-$(CONFIG_AL_FIC) += irq-al-fic.o + obj-$(CONFIG_ALPINE_MSI) += irq-alpine-msi.o + obj-$(CONFIG_ATH79) += irq-ath79-cpu.o ++obj-$(CONFIG_ATH79) += irq-ath79-intc.o + obj-$(CONFIG_ATH79) += irq-ath79-misc.o + obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o + obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2836.o +--- /dev/null ++++ b/drivers/irqchip/irq-ath79-intc.c +@@ -0,0 +1,142 @@ ++/* ++ * Atheros AR71xx/AR724x/AR913x specific interrupt handling ++ * ++ * Copyright (C) 2018 John Crispin <john@phrozen.org> ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ */ ++ ++#include <linux/interrupt.h> ++#include <linux/irqchip.h> ++#include <linux/of.h> ++#include <linux/of_irq.h> ++#include <linux/irqdomain.h> ++ ++#include <asm/irq_cpu.h> ++#include <asm/mach-ath79/ath79.h> ++#include <asm/mach-ath79/ar71xx_regs.h> ++ ++#define ATH79_MAX_INTC_CASCADE 3 ++ ++struct ath79_intc { ++ struct irq_chip chip; ++ u32 irq; ++ u32 pending_mask; ++ u32 int_status; ++ u32 irq_mask[ATH79_MAX_INTC_CASCADE]; ++ u32 irq_wb_chan[ATH79_MAX_INTC_CASCADE]; ++}; ++ ++static void ath79_intc_irq_handler(struct irq_desc *desc) ++{ ++ struct irq_domain *domain = irq_desc_get_handler_data(desc); ++ struct ath79_intc *intc = domain->host_data; ++ u32 pending; ++ ++ pending = ath79_reset_rr(intc->int_status); ++ pending &= intc->pending_mask; ++ ++ if (pending) { ++ int i; ++ ++ for (i = 0; i < domain->hwirq_max; i++) ++ if (pending & intc->irq_mask[i]) { ++ if (intc->irq_wb_chan[i] != 0xffffffff) ++ ath79_ddr_wb_flush(intc->irq_wb_chan[i]); ++ generic_handle_irq(irq_find_mapping(domain, i)); ++ } ++ } else { ++ spurious_interrupt(); ++ } ++} ++ ++static void ath79_intc_irq_enable(struct irq_data *d) ++{ ++ struct ath79_intc *intc = d->domain->host_data; ++ enable_irq(intc->irq); ++} ++ ++static void ath79_intc_irq_disable(struct irq_data *d) ++{ ++ struct ath79_intc *intc = d->domain->host_data; ++ disable_irq(intc->irq); ++} ++ ++static int ath79_intc_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw) ++{ ++ struct ath79_intc *intc = d->host_data; ++ ++ irq_set_chip_and_handler(irq, &intc->chip, handle_level_irq); ++ ++ return 0; ++} ++ ++static const struct irq_domain_ops ath79_irq_domain_ops = { ++ .xlate = irq_domain_xlate_onecell, ++ .map = ath79_intc_map, ++}; ++ ++static int __init ath79_intc_of_init( ++ struct device_node *node, struct device_node *parent) ++{ ++ struct irq_domain *domain; ++ struct ath79_intc *intc; ++ int cnt, cntwb, i, err; ++ ++ cnt = of_property_count_u32_elems(node, "qca,pending-bits"); ++ if (cnt > ATH79_MAX_INTC_CASCADE) ++ panic("Too many INTC pending bits\n"); ++ ++ intc = kzalloc(sizeof(*intc), GFP_KERNEL); ++ if (!intc) ++ panic("Failed to allocate INTC memory\n"); ++ intc->chip = dummy_irq_chip; ++ intc->chip.name = "INTC"; ++ intc->chip.irq_disable = ath79_intc_irq_disable; ++ intc->chip.irq_enable = ath79_intc_irq_enable; ++ ++ if (of_property_read_u32(node, "qca,int-status-addr", &intc->int_status) < 0) { ++ panic("Missing address of interrupt status register\n"); ++ } ++ ++ of_property_read_u32_array(node, "qca,pending-bits", intc->irq_mask, cnt); ++ for (i = 0; i < cnt; i++) { ++ intc->pending_mask |= intc->irq_mask[i]; ++ intc->irq_wb_chan[i] = 0xffffffff; ++ } ++ ++ cntwb = of_count_phandle_with_args( ++ node, "qca,ddr-wb-channels", "#qca,ddr-wb-channel-cells"); ++ ++ for (i = 0; i < cntwb; i++) { ++ struct of_phandle_args args; ++ u32 irq = i; ++ ++ of_property_read_u32_index( ++ node, "qca,ddr-wb-channel-interrupts", i, &irq); ++ if (irq >= ATH79_MAX_INTC_CASCADE) ++ continue; ++ ++ err = of_parse_phandle_with_args( ++ node, "qca,ddr-wb-channels", ++ "#qca,ddr-wb-channel-cells", ++ i, &args); ++ if (err) ++ return err; ++ ++ intc->irq_wb_chan[irq] = args.args[0]; ++ } ++ ++ intc->irq = irq_of_parse_and_map(node, 0); ++ if (!intc->irq) ++ panic("Failed to get INTC IRQ"); ++ ++ domain = irq_domain_add_linear(node, cnt, &ath79_irq_domain_ops, intc); ++ irq_set_chained_handler_and_data(intc->irq, ath79_intc_irq_handler, domain); ++ ++ return 0; ++} ++IRQCHIP_DECLARE(ath79_intc, "qca,ar9340-intc", ++ ath79_intc_of_init); diff --git a/target/linux/ath79/patches-5.10/0008-irqchip-irq-ath79-cpu-drop-OF-init-helper.patch b/target/linux/ath79/patches-5.10/0008-irqchip-irq-ath79-cpu-drop-OF-init-helper.patch new file mode 100644 index 0000000000..13117d9a8e --- /dev/null +++ b/target/linux/ath79/patches-5.10/0008-irqchip-irq-ath79-cpu-drop-OF-init-helper.patch @@ -0,0 +1,23 @@ +From e029f998594f151008ecbfa024e2957edd2a5189 Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Tue, 6 Mar 2018 09:58:19 +0100 +Subject: [PATCH 08/33] irqchip/irq-ath79-cpu: drop !OF init helper + +Signed-off-by: John Crispin <john@phrozen.org> +--- + drivers/irqchip/irq-ath79-cpu.c | 7 ------- + 1 file changed, 7 deletions(-) + +--- a/drivers/irqchip/irq-ath79-cpu.c ++++ b/drivers/irqchip/irq-ath79-cpu.c +@@ -85,10 +85,3 @@ static int __init ar79_cpu_intc_of_init( + } + IRQCHIP_DECLARE(ar79_cpu_intc, "qca,ar7100-cpu-intc", + ar79_cpu_intc_of_init); +- +-void __init ath79_cpu_irq_init(unsigned irq_wb_chan2, unsigned irq_wb_chan3) +-{ +- irq_wb_chan[2] = irq_wb_chan2; +- irq_wb_chan[3] = irq_wb_chan3; +- mips_cpu_irq_init(); +-} diff --git a/target/linux/ath79/patches-5.10/0017-dt-bindings-PCI-qcom-ar7100-adds-binding-doc.patch b/target/linux/ath79/patches-5.10/0017-dt-bindings-PCI-qcom-ar7100-adds-binding-doc.patch new file mode 100644 index 0000000000..bf7eb691a5 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0017-dt-bindings-PCI-qcom-ar7100-adds-binding-doc.patch @@ -0,0 +1,57 @@ +From 4a4f869ec58ed8910b9b2e68d0eee50957e9bb20 Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Mon, 25 Jun 2018 15:52:10 +0200 +Subject: [PATCH 17/33] dt-bindings: PCI: qcom,ar7100: adds binding doc + +With the driver being converted from platform_data to pure OF, we need to +also add some docs. + +Cc: Rob Herring <robh+dt@kernel.org> +Cc: devicetree@vger.kernel.org +Signed-off-by: John Crispin <john@phrozen.org> +--- + .../devicetree/bindings/pci/qcom,ar7100-pci.txt | 38 ++++++++++++++++++++++ + 1 file changed, 38 insertions(+) + create mode 100644 Documentation/devicetree/bindings/pci/qcom,ar7100-pci.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/pci/qcom,ar7100-pci.txt +@@ -0,0 +1,38 @@ ++* Qualcomm Atheros AR7100 PCI express root complex ++ ++Required properties: ++- compatible: should contain "qcom,ar7100-pci" to identify the core. ++- reg: Should contain the register ranges as listed in the reg-names property. ++- reg-names: Definition: Must include the following entries ++ - "cfg_base" IO Memory ++- #address-cells: set to <3> ++- #size-cells: set to <2> ++- ranges: ranges for the PCI memory and I/O regions ++- interrupt-map-mask and interrupt-map: standard PCI ++ properties to define the mapping of the PCIe interface to interrupt ++ numbers. ++- #interrupt-cells: set to <1> ++- interrupt-controller: define to enable the builtin IRQ cascade. ++ ++Optional properties: ++- interrupt-parent: phandle to the MIPS IRQ controller ++ ++* Example for ar7100 ++ pcie-controller@180c0000 { ++ compatible = "qca,ar7100-pci"; ++ #address-cells = <3>; ++ #size-cells = <2>; ++ bus-range = <0x0 0x0>; ++ reg = <0x17010000 0x100>; ++ reg-names = "cfg_base"; ++ ranges = <0x2000000 0 0x10000000 0x10000000 0 0x07000000 ++ 0x1000000 0 0x00000000 0x00000000 0 0x00000001>; ++ interrupt-parent = <&cpuintc>; ++ interrupts = <2>; ++ ++ interrupt-controller; ++ #interrupt-cells = <1>; ++ ++ interrupt-map-mask = <0 0 0 1>; ++ interrupt-map = <0 0 0 0 &pcie0 0>; ++ }; diff --git a/target/linux/ath79/patches-5.10/0018-MIPS-pci-ar71xx-convert-to-OF.patch b/target/linux/ath79/patches-5.10/0018-MIPS-pci-ar71xx-convert-to-OF.patch new file mode 100644 index 0000000000..e600a4f0d9 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0018-MIPS-pci-ar71xx-convert-to-OF.patch @@ -0,0 +1,202 @@ +From 1855ab6b1d27f5b38a648baf57ff6a534afec26d Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Sat, 23 Jun 2018 15:07:23 +0200 +Subject: [PATCH 18/33] MIPS: pci-ar71xx: convert to OF + +With the ath79 target getting converted to pure OF, we can drop all the +platform data code and add the missing OF bits to the driver. We also add +a irq domain for the PCI/e controllers cascade, thus making it usable from +dts files. + +Signed-off-by: John Crispin <john@phrozen.org> +--- + arch/mips/pci/pci-ar71xx.c | 82 +++++++++++++++++++++++----------------------- + 1 file changed, 41 insertions(+), 41 deletions(-) + +--- a/arch/mips/pci/pci-ar71xx.c ++++ b/arch/mips/pci/pci-ar71xx.c +@@ -15,8 +15,11 @@ + #include <linux/pci.h> + #include <linux/pci_regs.h> + #include <linux/interrupt.h> ++#include <linux/irqchip/chained_irq.h> + #include <linux/init.h> + #include <linux/platform_device.h> ++#include <linux/of_irq.h> ++#include <linux/of_pci.h> + + #include <asm/mach-ath79/ar71xx_regs.h> + #include <asm/mach-ath79/ath79.h> +@@ -46,12 +49,13 @@ + #define AR71XX_PCI_IRQ_COUNT 5 + + struct ar71xx_pci_controller { ++ struct device_node *np; + void __iomem *cfg_base; + int irq; +- int irq_base; + struct pci_controller pci_ctrl; + struct resource io_res; + struct resource mem_res; ++ struct irq_domain *domain; + }; + + /* Byte lane enable bits */ +@@ -225,29 +229,30 @@ static struct pci_ops ar71xx_pci_ops = { + + static void ar71xx_pci_irq_handler(struct irq_desc *desc) + { +- struct ar71xx_pci_controller *apc; + void __iomem *base = ath79_reset_base; ++ struct irq_chip *chip = irq_desc_get_chip(desc); ++ struct ar71xx_pci_controller *apc = irq_desc_get_handler_data(desc); + u32 pending; + +- apc = irq_desc_get_handler_data(desc); +- ++ chained_irq_enter(chip, desc); + pending = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_STATUS) & + __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); + + if (pending & AR71XX_PCI_INT_DEV0) +- generic_handle_irq(apc->irq_base + 0); ++ generic_handle_irq(irq_linear_revmap(apc->domain, 1)); + + else if (pending & AR71XX_PCI_INT_DEV1) +- generic_handle_irq(apc->irq_base + 1); ++ generic_handle_irq(irq_linear_revmap(apc->domain, 2)); + + else if (pending & AR71XX_PCI_INT_DEV2) +- generic_handle_irq(apc->irq_base + 2); ++ generic_handle_irq(irq_linear_revmap(apc->domain, 3)); + + else if (pending & AR71XX_PCI_INT_CORE) +- generic_handle_irq(apc->irq_base + 4); ++ generic_handle_irq(irq_linear_revmap(apc->domain, 4)); + + else + spurious_interrupt(); ++ chained_irq_exit(chip, desc); + } + + static void ar71xx_pci_irq_unmask(struct irq_data *d) +@@ -258,7 +263,7 @@ static void ar71xx_pci_irq_unmask(struct + u32 t; + + apc = irq_data_get_irq_chip_data(d); +- irq = d->irq - apc->irq_base; ++ irq = irq_linear_revmap(apc->domain, d->irq); + + t = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); + __raw_writel(t | (1 << irq), base + AR71XX_RESET_REG_PCI_INT_ENABLE); +@@ -275,7 +280,7 @@ static void ar71xx_pci_irq_mask(struct i + u32 t; + + apc = irq_data_get_irq_chip_data(d); +- irq = d->irq - apc->irq_base; ++ irq = irq_linear_revmap(apc->domain, d->irq); + + t = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); + __raw_writel(t & ~(1 << irq), base + AR71XX_RESET_REG_PCI_INT_ENABLE); +@@ -291,24 +296,31 @@ static struct irq_chip ar71xx_pci_irq_ch + .irq_mask_ack = ar71xx_pci_irq_mask, + }; + ++static int ar71xx_pci_irq_map(struct irq_domain *d, ++ unsigned int irq, irq_hw_number_t hw) ++{ ++ struct ar71xx_pci_controller *apc = d->host_data; ++ ++ irq_set_chip_and_handler(irq, &ar71xx_pci_irq_chip, handle_level_irq); ++ irq_set_chip_data(irq, apc); ++ ++ return 0; ++} ++ ++static const struct irq_domain_ops ar71xx_pci_domain_ops = { ++ .xlate = irq_domain_xlate_onecell, ++ .map = ar71xx_pci_irq_map, ++}; ++ + static void ar71xx_pci_irq_init(struct ar71xx_pci_controller *apc) + { + void __iomem *base = ath79_reset_base; +- int i; + + __raw_writel(0, base + AR71XX_RESET_REG_PCI_INT_ENABLE); + __raw_writel(0, base + AR71XX_RESET_REG_PCI_INT_STATUS); + +- BUILD_BUG_ON(ATH79_PCI_IRQ_COUNT < AR71XX_PCI_IRQ_COUNT); +- +- apc->irq_base = ATH79_PCI_IRQ_BASE; +- for (i = apc->irq_base; +- i < apc->irq_base + AR71XX_PCI_IRQ_COUNT; i++) { +- irq_set_chip_and_handler(i, &ar71xx_pci_irq_chip, +- handle_level_irq); +- irq_set_chip_data(i, apc); +- } +- ++ apc->domain = irq_domain_add_linear(apc->np, AR71XX_PCI_IRQ_COUNT, ++ &ar71xx_pci_domain_ops, apc); + irq_set_chained_handler_and_data(apc->irq, ar71xx_pci_irq_handler, + apc); + } +@@ -325,6 +337,11 @@ static void ar71xx_pci_reset(void) + mdelay(100); + } + ++static const struct of_device_id ar71xx_pci_ids[] = { ++ { .compatible = "qca,ar7100-pci" }, ++ {}, ++}; ++ + static int ar71xx_pci_probe(struct platform_device *pdev) + { + struct ar71xx_pci_controller *apc; +@@ -345,26 +362,6 @@ static int ar71xx_pci_probe(struct platf + if (apc->irq < 0) + return -EINVAL; + +- res = platform_get_resource_byname(pdev, IORESOURCE_IO, "io_base"); +- if (!res) +- return -EINVAL; +- +- apc->io_res.parent = res; +- apc->io_res.name = "PCI IO space"; +- apc->io_res.start = res->start; +- apc->io_res.end = res->end; +- apc->io_res.flags = IORESOURCE_IO; +- +- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mem_base"); +- if (!res) +- return -EINVAL; +- +- apc->mem_res.parent = res; +- apc->mem_res.name = "PCI memory space"; +- apc->mem_res.start = res->start; +- apc->mem_res.end = res->end; +- apc->mem_res.flags = IORESOURCE_MEM; +- + ar71xx_pci_reset(); + + /* setup COMMAND register */ +@@ -377,9 +374,11 @@ static int ar71xx_pci_probe(struct platf + + ar71xx_pci_irq_init(apc); + ++ apc->np = pdev->dev.of_node; + apc->pci_ctrl.pci_ops = &ar71xx_pci_ops; + apc->pci_ctrl.mem_resource = &apc->mem_res; + apc->pci_ctrl.io_resource = &apc->io_res; ++ pci_load_of_ranges(&apc->pci_ctrl, pdev->dev.of_node); + + register_pci_controller(&apc->pci_ctrl); + +@@ -390,6 +389,7 @@ static struct platform_driver ar71xx_pci + .probe = ar71xx_pci_probe, + .driver = { + .name = "ar71xx-pci", ++ .of_match_table = of_match_ptr(ar71xx_pci_ids), + }, + }; + diff --git a/target/linux/ath79/patches-5.10/0019-dt-bindings-PCI-qcom-ar7240-adds-binding-doc.patch b/target/linux/ath79/patches-5.10/0019-dt-bindings-PCI-qcom-ar7240-adds-binding-doc.patch new file mode 100644 index 0000000000..a0af79cb4d --- /dev/null +++ b/target/linux/ath79/patches-5.10/0019-dt-bindings-PCI-qcom-ar7240-adds-binding-doc.patch @@ -0,0 +1,61 @@ +From ea27764bc3ef2a05decf3ae05edffc289cd0d93c Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Mon, 25 Jun 2018 15:52:02 +0200 +Subject: [PATCH 19/33] dt-bindings: PCI: qcom,ar7240: adds binding doc + +With the driver being converted from platform_data to pure OF, we need to +also add some docs. + +Cc: Rob Herring <robh+dt@kernel.org> +Cc: devicetree@vger.kernel.org +Signed-off-by: John Crispin <john@phrozen.org> +--- + .../devicetree/bindings/pci/qcom,ar7240-pci.txt | 42 ++++++++++++++++++++++ + 1 file changed, 42 insertions(+) + create mode 100644 Documentation/devicetree/bindings/pci/qcom,ar7240-pci.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/pci/qcom,ar7240-pci.txt +@@ -0,0 +1,42 @@ ++* Qualcomm Atheros AR724X PCI express root complex ++ ++Required properties: ++- compatible: should contain "qcom,ar7240-pci" to identify the core. ++- reg: Should contain the register ranges as listed in the reg-names property. ++- reg-names: Definition: Must include the following entries ++ - "crp_base" Configuration registers ++ - "ctrl_base" Control registers ++ - "cfg_base" IO Memory ++- #address-cells: set to <3> ++- #size-cells: set to <2> ++- ranges: ranges for the PCI memory and I/O regions ++- interrupt-map-mask and interrupt-map: standard PCI ++ properties to define the mapping of the PCIe interface to interrupt ++ numbers. ++- #interrupt-cells: set to <1> ++- interrupt-parent: phandle to the MIPS IRQ controller ++ ++Optional properties: ++- interrupt-controller: define to enable the builtin IRQ cascade. ++ ++* Example for qca9557 ++ pcie-controller@180c0000 { ++ compatible = "qcom,ar7240-pci"; ++ #address-cells = <3>; ++ #size-cells = <2>; ++ bus-range = <0x0 0x0>; ++ reg = <0x180c0000 0x1000>, ++ <0x180f0000 0x100>, ++ <0x14000000 0x1000>; ++ reg-names = "crp_base", "ctrl_base", "cfg_base"; ++ ranges = <0x2000000 0 0x10000000 0x10000000 0 0x04000000 ++ 0x1000000 0 0x00000000 0x00000000 0 0x00000001>; ++ interrupt-parent = <&intc2>; ++ interrupts = <1>; ++ ++ interrupt-controller; ++ #interrupt-cells = <1>; ++ ++ interrupt-map-mask = <0 0 0 1>; ++ interrupt-map = <0 0 0 0 &pcie0 0>; ++ }; diff --git a/target/linux/ath79/patches-5.10/0020-MIPS-pci-ar724x-convert-to-OF.patch b/target/linux/ath79/patches-5.10/0020-MIPS-pci-ar724x-convert-to-OF.patch new file mode 100644 index 0000000000..b8a877c63d --- /dev/null +++ b/target/linux/ath79/patches-5.10/0020-MIPS-pci-ar724x-convert-to-OF.patch @@ -0,0 +1,205 @@ +From a522ee0199d5d3ea114ca2e211f6ac398d3e8e0b Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Sat, 23 Jun 2018 15:07:37 +0200 +Subject: [PATCH 20/33] MIPS: pci-ar724x: convert to OF + +With the ath79 target getting converted to pure OF, we can drop all the +platform data code and add the missing OF bits to the driver. We also add +a irq domain for the PCI/e controllers cascade, thus making it usable from +dts files. + +Signed-off-by: John Crispin <john@phrozen.org> +--- + arch/mips/pci/pci-ar724x.c | 88 ++++++++++++++++++++++------------------------ + 1 file changed, 42 insertions(+), 46 deletions(-) + +--- a/arch/mips/pci/pci-ar724x.c ++++ b/arch/mips/pci/pci-ar724x.c +@@ -11,8 +11,11 @@ + #include <linux/init.h> + #include <linux/delay.h> + #include <linux/platform_device.h> ++#include <linux/irqchip/chained_irq.h> + #include <asm/mach-ath79/ath79.h> + #include <asm/mach-ath79/ar71xx_regs.h> ++#include <linux/of_irq.h> ++#include <linux/of_pci.h> + + #define AR724X_PCI_REG_APP 0x00 + #define AR724X_PCI_REG_RESET 0x18 +@@ -42,17 +45,20 @@ struct ar724x_pci_controller { + void __iomem *crp_base; + + int irq; +- int irq_base; + + bool link_up; + bool bar0_is_cached; + u32 bar0_value; + ++ struct device_node *np; + struct pci_controller pci_controller; ++ struct irq_domain *domain; + struct resource io_res; + struct resource mem_res; + }; + ++static struct irq_chip ar724x_pci_irq_chip; ++ + static inline bool ar724x_pci_check_link(struct ar724x_pci_controller *apc) + { + u32 reset; +@@ -228,35 +234,31 @@ static struct pci_ops ar724x_pci_ops = { + + static void ar724x_pci_irq_handler(struct irq_desc *desc) + { +- struct ar724x_pci_controller *apc; +- void __iomem *base; ++ struct irq_chip *chip = irq_desc_get_chip(desc); ++ struct ar724x_pci_controller *apc = irq_desc_get_handler_data(desc); + u32 pending; + +- apc = irq_desc_get_handler_data(desc); +- base = apc->ctrl_base; +- +- pending = __raw_readl(base + AR724X_PCI_REG_INT_STATUS) & +- __raw_readl(base + AR724X_PCI_REG_INT_MASK); ++ chained_irq_enter(chip, desc); ++ pending = __raw_readl(apc->ctrl_base + AR724X_PCI_REG_INT_STATUS) & ++ __raw_readl(apc->ctrl_base + AR724X_PCI_REG_INT_MASK); + + if (pending & AR724X_PCI_INT_DEV0) +- generic_handle_irq(apc->irq_base + 0); +- ++ generic_handle_irq(irq_linear_revmap(apc->domain, 1)); + else + spurious_interrupt(); ++ chained_irq_exit(chip, desc); + } + + static void ar724x_pci_irq_unmask(struct irq_data *d) + { + struct ar724x_pci_controller *apc; + void __iomem *base; +- int offset; + u32 t; + + apc = irq_data_get_irq_chip_data(d); + base = apc->ctrl_base; +- offset = apc->irq_base - d->irq; + +- switch (offset) { ++ switch (irq_linear_revmap(apc->domain, d->irq)) { + case 0: + t = __raw_readl(base + AR724X_PCI_REG_INT_MASK); + __raw_writel(t | AR724X_PCI_INT_DEV0, +@@ -270,14 +272,12 @@ static void ar724x_pci_irq_mask(struct i + { + struct ar724x_pci_controller *apc; + void __iomem *base; +- int offset; + u32 t; + + apc = irq_data_get_irq_chip_data(d); + base = apc->ctrl_base; +- offset = apc->irq_base - d->irq; + +- switch (offset) { ++ switch (irq_linear_revmap(apc->domain, d->irq)) { + case 0: + t = __raw_readl(base + AR724X_PCI_REG_INT_MASK); + __raw_writel(t & ~AR724X_PCI_INT_DEV0, +@@ -302,26 +302,34 @@ static struct irq_chip ar724x_pci_irq_ch + .irq_mask_ack = ar724x_pci_irq_mask, + }; + ++static int ar724x_pci_irq_map(struct irq_domain *d, ++ unsigned int irq, irq_hw_number_t hw) ++{ ++ struct ar724x_pci_controller *apc = d->host_data; ++ ++ irq_set_chip_and_handler(irq, &ar724x_pci_irq_chip, handle_level_irq); ++ irq_set_chip_data(irq, apc); ++ ++ return 0; ++} ++ ++static const struct irq_domain_ops ar724x_pci_domain_ops = { ++ .xlate = irq_domain_xlate_onecell, ++ .map = ar724x_pci_irq_map, ++}; ++ + static void ar724x_pci_irq_init(struct ar724x_pci_controller *apc, + int id) + { + void __iomem *base; +- int i; + + base = apc->ctrl_base; + + __raw_writel(0, base + AR724X_PCI_REG_INT_MASK); + __raw_writel(0, base + AR724X_PCI_REG_INT_STATUS); + +- apc->irq_base = ATH79_PCI_IRQ_BASE + (id * AR724X_PCI_IRQ_COUNT); +- +- for (i = apc->irq_base; +- i < apc->irq_base + AR724X_PCI_IRQ_COUNT; i++) { +- irq_set_chip_and_handler(i, &ar724x_pci_irq_chip, +- handle_level_irq); +- irq_set_chip_data(i, apc); +- } +- ++ apc->domain = irq_domain_add_linear(apc->np, 2, ++ &ar724x_pci_domain_ops, apc); + irq_set_chained_handler_and_data(apc->irq, ar724x_pci_irq_handler, + apc); + } +@@ -391,29 +399,11 @@ static int ar724x_pci_probe(struct platf + if (apc->irq < 0) + return -EINVAL; + +- res = platform_get_resource_byname(pdev, IORESOURCE_IO, "io_base"); +- if (!res) +- return -EINVAL; +- +- apc->io_res.parent = res; +- apc->io_res.name = "PCI IO space"; +- apc->io_res.start = res->start; +- apc->io_res.end = res->end; +- apc->io_res.flags = IORESOURCE_IO; +- +- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mem_base"); +- if (!res) +- return -EINVAL; +- +- apc->mem_res.parent = res; +- apc->mem_res.name = "PCI memory space"; +- apc->mem_res.start = res->start; +- apc->mem_res.end = res->end; +- apc->mem_res.flags = IORESOURCE_MEM; +- ++ apc->np = pdev->dev.of_node; + apc->pci_controller.pci_ops = &ar724x_pci_ops; + apc->pci_controller.io_resource = &apc->io_res; + apc->pci_controller.mem_resource = &apc->mem_res; ++ pci_load_of_ranges(&apc->pci_controller, pdev->dev.of_node); + + /* + * Do the full PCIE Root Complex Initialization Sequence if the PCIe +@@ -435,10 +425,16 @@ static int ar724x_pci_probe(struct platf + return 0; + } + ++static const struct of_device_id ar724x_pci_ids[] = { ++ { .compatible = "qcom,ar7240-pci" }, ++ {}, ++}; ++ + static struct platform_driver ar724x_pci_driver = { + .probe = ar724x_pci_probe, + .driver = { + .name = "ar724x-pci", ++ .of_match_table = of_match_ptr(ar724x_pci_ids), + }, + }; + diff --git a/target/linux/ath79/patches-5.10/0032-MIPS-ath79-sanitize-symbols.patch b/target/linux/ath79/patches-5.10/0032-MIPS-ath79-sanitize-symbols.patch new file mode 100644 index 0000000000..14dddd5147 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0032-MIPS-ath79-sanitize-symbols.patch @@ -0,0 +1,93 @@ +From 3fc8585cf76022dba7496627074d42af88c30718 Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Sat, 23 Jun 2018 15:16:55 +0200 +Subject: [PATCH 32/33] MIPS: ath79: sanitize symbols + +We no longer need to select which SoCs are supported as the whole arch +code is always built. So lets drop all the SoC symbols + +Signed-off-by: John Crispin <john@phrozen.org> +--- + arch/mips/Kconfig | 2 ++ + arch/mips/ath79/Kconfig | 44 +++++--------------------------------------- + arch/mips/pci/Makefile | 2 +- + 3 files changed, 8 insertions(+), 40 deletions(-) + +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -217,6 +217,8 @@ config ATH79 + select SYS_SUPPORTS_BIG_ENDIAN + select SYS_SUPPORTS_MIPS16 + select SYS_SUPPORTS_ZBOOT_UART_PROM ++ select HAVE_PCI ++ select USB_ARCH_HAS_EHCI + select USE_OF + select USB_EHCI_ROOT_HUB_TT if USB_EHCI_HCD_PLATFORM + help +--- a/arch/mips/ath79/Kconfig ++++ b/arch/mips/ath79/Kconfig +@@ -1,48 +1,14 @@ + # SPDX-License-Identifier: GPL-2.0 + if ATH79 + +-config SOC_AR71XX +- select HAVE_PCI +- def_bool n +- +-config SOC_AR724X +- select HAVE_PCI +- select PCI_AR724X if PCI +- def_bool n +- +-config SOC_AR913X +- def_bool n +- +-config SOC_AR933X +- def_bool n +- +-config SOC_AR934X +- select HAVE_PCI +- select PCI_AR724X if PCI +- def_bool n +- +-config SOC_QCA955X +- select HAVE_PCI +- select PCI_AR724X if PCI ++config PCI_AR71XX ++ bool "PCI support for AR7100 type SoCs" ++ depends on PCI + def_bool n + + config PCI_AR724X +- def_bool n +- +-config ATH79_DEV_GPIO_BUTTONS +- def_bool n +- +-config ATH79_DEV_LEDS_GPIO +- def_bool n +- +-config ATH79_DEV_SPI +- def_bool n +- +-config ATH79_DEV_USB +- def_bool n +- +-config ATH79_DEV_WMAC +- depends on (SOC_AR913X || SOC_AR933X || SOC_AR934X || SOC_QCA955X) ++ bool "PCI support for AR724x type SoCs" ++ depends on PCI + def_bool n + + endif +--- a/arch/mips/pci/Makefile ++++ b/arch/mips/pci/Makefile +@@ -23,7 +23,7 @@ obj-$(CONFIG_BCM63XX) += pci-bcm63xx.o + ops-bcm63xx.o + obj-$(CONFIG_MIPS_ALCHEMY) += pci-alchemy.o + obj-$(CONFIG_PCI_AR2315) += pci-ar2315.o +-obj-$(CONFIG_SOC_AR71XX) += pci-ar71xx.o ++obj-$(CONFIG_PCI_AR71XX) += pci-ar71xx.o + obj-$(CONFIG_PCI_AR724X) += pci-ar724x.o + obj-$(CONFIG_MIPS_PCI_VIRTIO) += pci-virtio-guest.o + obj-$(CONFIG_PCI_XTALK_BRIDGE) += pci-xtalk-bridge.o diff --git a/target/linux/ath79/patches-5.10/0033-spi-ath79-drop-pdata-support.patch b/target/linux/ath79/patches-5.10/0033-spi-ath79-drop-pdata-support.patch new file mode 100644 index 0000000000..8fd99bd333 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0033-spi-ath79-drop-pdata-support.patch @@ -0,0 +1,71 @@ +From c4e197bbcecc7233aa9e553e7047fa50e4e1fe77 Mon Sep 17 00:00:00 2001 +From: John Crispin <john@phrozen.org> +Date: Mon, 25 Jun 2018 15:52:34 +0200 +Subject: [PATCH 33/33] spi: ath79: drop pdata support + +The target is being converted to pure OF. We can therefore drop all of the +platform data code from the driver. + +Cc: linux-spi@vger.kernel.org +Acked-by: Mark Brown <broonie@kernel.org> +Signed-off-by: John Crispin <john@phrozen.org> +--- + include/linux/platform_data/spi-ath79.h | 16 ------------------- + drivers/spi/spi-ath79.c | 8 -------- + 2 files changed, 27 deletions(-) + delete mode 100644 arch/mips/include/asm/mach-ath79/ath79_spi_platform.h + +--- a/include/linux/platform_data/spi-ath79.h ++++ /dev/null +@@ -1,16 +0,0 @@ +-/* SPDX-License-Identifier: GPL-2.0-only */ +-/* +- * Platform data definition for Atheros AR71XX/AR724X/AR913X SPI controller +- * +- * Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org> +- */ +- +-#ifndef _ATH79_SPI_PLATFORM_H +-#define _ATH79_SPI_PLATFORM_H +- +-struct ath79_spi_platform_data { +- unsigned bus_num; +- unsigned num_chipselect; +-}; +- +-#endif /* _ATH79_SPI_PLATFORM_H */ +--- a/drivers/spi/spi-ath79.c ++++ b/drivers/spi/spi-ath79.c +@@ -19,7 +19,6 @@ + #include <linux/bitops.h> + #include <linux/clk.h> + #include <linux/err.h> +-#include <linux/platform_data/spi-ath79.h> + + #define DRV_NAME "ath79-spi" + +@@ -138,7 +137,6 @@ static int ath79_spi_probe(struct platfo + { + struct spi_master *master; + struct ath79_spi *sp; +- struct ath79_spi_platform_data *pdata; + unsigned long rate; + int ret; + +@@ -152,16 +150,10 @@ static int ath79_spi_probe(struct platfo + master->dev.of_node = pdev->dev.of_node; + platform_set_drvdata(pdev, sp); + +- pdata = dev_get_platdata(&pdev->dev); +- + master->use_gpio_descriptors = true; + master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32); + master->setup = spi_bitbang_setup; + master->cleanup = spi_bitbang_cleanup; +- if (pdata) { +- master->bus_num = pdata->bus_num; +- master->num_chipselect = pdata->num_chipselect; +- } + + sp->bitbang.master = master; + sp->bitbang.chipselect = ath79_spi_chipselect; diff --git a/target/linux/ath79/patches-5.10/0034-MIPS-ath79-ath9k-exports.patch b/target/linux/ath79/patches-5.10/0034-MIPS-ath79-ath9k-exports.patch new file mode 100644 index 0000000000..71acc22210 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0034-MIPS-ath79-ath9k-exports.patch @@ -0,0 +1,27 @@ +--- a/arch/mips/ath79/common.c ++++ b/arch/mips/ath79/common.c +@@ -31,11 +31,13 @@ EXPORT_SYMBOL_GPL(ath79_ddr_freq); + + enum ath79_soc_type ath79_soc; + unsigned int ath79_soc_rev; ++EXPORT_SYMBOL_GPL(ath79_soc_rev); + + void __iomem *ath79_pll_base; + void __iomem *ath79_reset_base; + EXPORT_SYMBOL_GPL(ath79_reset_base); +-static void __iomem *ath79_ddr_base; ++void __iomem *ath79_ddr_base; ++EXPORT_SYMBOL_GPL(ath79_ddr_base); + static void __iomem *ath79_ddr_wb_flush_base; + static void __iomem *ath79_ddr_pci_win_base; + +--- a/arch/mips/include/asm/mach-ath79/ath79.h ++++ b/arch/mips/include/asm/mach-ath79/ath79.h +@@ -149,6 +149,7 @@ void ath79_ddr_wb_flush(unsigned int reg + void ath79_ddr_set_pci_windows(void); + + extern void __iomem *ath79_pll_base; ++extern void __iomem *ath79_ddr_base; + extern void __iomem *ath79_reset_base; + + static inline void ath79_pll_wr(unsigned reg, u32 val) diff --git a/target/linux/ath79/patches-5.10/0036-GPIO-add-named-gpio-exports.patch b/target/linux/ath79/patches-5.10/0036-GPIO-add-named-gpio-exports.patch new file mode 100644 index 0000000000..d4ea379159 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0036-GPIO-add-named-gpio-exports.patch @@ -0,0 +1,165 @@ +From 4267880319bc1a2270d352e0ded6d6386242a7ef Mon Sep 17 00:00:00 2001 +From: John Crispin <blogic@openwrt.org> +Date: Tue, 12 Aug 2014 20:49:27 +0200 +Subject: [PATCH 24/53] GPIO: add named gpio exports + +Signed-off-by: John Crispin <blogic@openwrt.org> +--- + drivers/gpio/gpiolib-of.c | 68 +++++++++++++++++++++++++++++++++++++++++ + drivers/gpio/gpiolib-sysfs.c | 10 +++++- + include/asm-generic/gpio.h | 6 ++++ + include/linux/gpio/consumer.h | 8 +++++ + 4 files changed, 91 insertions(+), 1 deletion(-) + +--- a/drivers/gpio/gpiolib-of.c ++++ b/drivers/gpio/gpiolib-of.c +@@ -19,6 +19,8 @@ + #include <linux/pinctrl/pinctrl.h> + #include <linux/slab.h> + #include <linux/gpio/machine.h> ++#include <linux/init.h> ++#include <linux/platform_device.h> + + #include "gpiolib.h" + #include "gpiolib-of.h" +@@ -915,3 +917,68 @@ void of_gpiochip_remove(struct gpio_chip + { + of_node_put(chip->of_node); + } ++ ++static struct of_device_id gpio_export_ids[] = { ++ { .compatible = "gpio-export" }, ++ { /* sentinel */ } ++}; ++ ++static int of_gpio_export_probe(struct platform_device *pdev) ++{ ++ struct device_node *np = pdev->dev.of_node; ++ struct device_node *cnp; ++ u32 val; ++ int nb = 0; ++ ++ for_each_child_of_node(np, cnp) { ++ const char *name = NULL; ++ int gpio; ++ bool dmc; ++ int max_gpio = 1; ++ int i; ++ ++ of_property_read_string(cnp, "gpio-export,name", &name); ++ ++ if (!name) ++ max_gpio = of_gpio_count(cnp); ++ ++ for (i = 0; i < max_gpio; i++) { ++ unsigned flags = 0; ++ enum of_gpio_flags of_flags; ++ ++ gpio = of_get_gpio_flags(cnp, i, &of_flags); ++ if (!gpio_is_valid(gpio)) ++ return gpio; ++ ++ if (of_flags == OF_GPIO_ACTIVE_LOW) ++ flags |= GPIOF_ACTIVE_LOW; ++ ++ if (!of_property_read_u32(cnp, "gpio-export,output", &val)) ++ flags |= val ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; ++ else ++ flags |= GPIOF_IN; ++ ++ if (devm_gpio_request_one(&pdev->dev, gpio, flags, name ? name : of_node_full_name(np))) ++ continue; ++ ++ dmc = of_property_read_bool(cnp, "gpio-export,direction_may_change"); ++ gpio_export_with_name(gpio, dmc, name); ++ nb++; ++ } ++ } ++ ++ dev_info(&pdev->dev, "%d gpio(s) exported\n", nb); ++ ++ return 0; ++} ++ ++static struct platform_driver gpio_export_driver = { ++ .driver = { ++ .name = "gpio-export", ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(gpio_export_ids), ++ }, ++ .probe = of_gpio_export_probe, ++}; ++ ++module_platform_driver(gpio_export_driver); +--- a/drivers/gpio/gpiolib-sysfs.c ++++ b/drivers/gpio/gpiolib-sysfs.c +@@ -563,7 +563,7 @@ static struct class gpio_class = { + * + * Returns zero on success, else an error. + */ +-int gpiod_export(struct gpio_desc *desc, bool direction_may_change) ++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name) + { + struct gpio_chip *chip; + struct gpio_device *gdev; +@@ -625,6 +625,8 @@ int gpiod_export(struct gpio_desc *desc, + offset = gpio_chip_hwgpio(desc); + if (chip->names && chip->names[offset]) + ioname = chip->names[offset]; ++ if (name) ++ ioname = name; + + dev = device_create_with_groups(&gpio_class, &gdev->dev, + MKDEV(0, 0), data, gpio_groups, +@@ -646,6 +648,12 @@ err_unlock: + gpiod_dbg(desc, "%s: status %d\n", __func__, status); + return status; + } ++EXPORT_SYMBOL_GPL(__gpiod_export); ++ ++int gpiod_export(struct gpio_desc *desc, bool direction_may_change) ++{ ++ return __gpiod_export(desc, direction_may_change, NULL); ++} + EXPORT_SYMBOL_GPL(gpiod_export); + + static int match_export(struct device *dev, const void *desc) +--- a/include/asm-generic/gpio.h ++++ b/include/asm-generic/gpio.h +@@ -127,6 +127,12 @@ static inline int gpio_export(unsigned g + return gpiod_export(gpio_to_desc(gpio), direction_may_change); + } + ++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name); ++static inline int gpio_export_with_name(unsigned gpio, bool direction_may_change, const char *name) ++{ ++ return __gpiod_export(gpio_to_desc(gpio), direction_may_change, name); ++} ++ + static inline int gpio_export_link(struct device *dev, const char *name, + unsigned gpio) + { +--- a/include/linux/gpio/consumer.h ++++ b/include/linux/gpio/consumer.h +@@ -668,6 +668,7 @@ static inline void devm_acpi_dev_remove_ + + #if IS_ENABLED(CONFIG_GPIOLIB) && IS_ENABLED(CONFIG_GPIO_SYSFS) + ++int _gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name); + int gpiod_export(struct gpio_desc *desc, bool direction_may_change); + int gpiod_export_link(struct device *dev, const char *name, + struct gpio_desc *desc); +@@ -675,6 +676,13 @@ void gpiod_unexport(struct gpio_desc *de + + #else /* CONFIG_GPIOLIB && CONFIG_GPIO_SYSFS */ + ++static inline int _gpiod_export(struct gpio_desc *desc, ++ bool direction_may_change, ++ const char *name) ++{ ++ return -ENOSYS; ++} ++ + static inline int gpiod_export(struct gpio_desc *desc, + bool direction_may_change) + { diff --git a/target/linux/ath79/patches-5.10/0036-MIPS-ath79-remove-irq-code-from-pci.patch b/target/linux/ath79/patches-5.10/0036-MIPS-ath79-remove-irq-code-from-pci.patch new file mode 100644 index 0000000000..80fcd0a7f5 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0036-MIPS-ath79-remove-irq-code-from-pci.patch @@ -0,0 +1,139 @@ +--- a/arch/mips/pci/pci-ar71xx.c ++++ b/arch/mips/pci/pci-ar71xx.c +@@ -51,11 +51,9 @@ + struct ar71xx_pci_controller { + struct device_node *np; + void __iomem *cfg_base; +- int irq; + struct pci_controller pci_ctrl; + struct resource io_res; + struct resource mem_res; +- struct irq_domain *domain; + }; + + /* Byte lane enable bits */ +@@ -227,104 +225,6 @@ static struct pci_ops ar71xx_pci_ops = { + .write = ar71xx_pci_write_config, + }; + +-static void ar71xx_pci_irq_handler(struct irq_desc *desc) +-{ +- void __iomem *base = ath79_reset_base; +- struct irq_chip *chip = irq_desc_get_chip(desc); +- struct ar71xx_pci_controller *apc = irq_desc_get_handler_data(desc); +- u32 pending; +- +- chained_irq_enter(chip, desc); +- pending = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_STATUS) & +- __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); +- +- if (pending & AR71XX_PCI_INT_DEV0) +- generic_handle_irq(irq_linear_revmap(apc->domain, 1)); +- +- else if (pending & AR71XX_PCI_INT_DEV1) +- generic_handle_irq(irq_linear_revmap(apc->domain, 2)); +- +- else if (pending & AR71XX_PCI_INT_DEV2) +- generic_handle_irq(irq_linear_revmap(apc->domain, 3)); +- +- else if (pending & AR71XX_PCI_INT_CORE) +- generic_handle_irq(irq_linear_revmap(apc->domain, 4)); +- +- else +- spurious_interrupt(); +- chained_irq_exit(chip, desc); +-} +- +-static void ar71xx_pci_irq_unmask(struct irq_data *d) +-{ +- struct ar71xx_pci_controller *apc; +- unsigned int irq; +- void __iomem *base = ath79_reset_base; +- u32 t; +- +- apc = irq_data_get_irq_chip_data(d); +- irq = irq_linear_revmap(apc->domain, d->irq); +- +- t = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); +- __raw_writel(t | (1 << irq), base + AR71XX_RESET_REG_PCI_INT_ENABLE); +- +- /* flush write */ +- __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); +-} +- +-static void ar71xx_pci_irq_mask(struct irq_data *d) +-{ +- struct ar71xx_pci_controller *apc; +- unsigned int irq; +- void __iomem *base = ath79_reset_base; +- u32 t; +- +- apc = irq_data_get_irq_chip_data(d); +- irq = irq_linear_revmap(apc->domain, d->irq); +- +- t = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); +- __raw_writel(t & ~(1 << irq), base + AR71XX_RESET_REG_PCI_INT_ENABLE); +- +- /* flush write */ +- __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE); +-} +- +-static struct irq_chip ar71xx_pci_irq_chip = { +- .name = "AR71XX PCI", +- .irq_mask = ar71xx_pci_irq_mask, +- .irq_unmask = ar71xx_pci_irq_unmask, +- .irq_mask_ack = ar71xx_pci_irq_mask, +-}; +- +-static int ar71xx_pci_irq_map(struct irq_domain *d, +- unsigned int irq, irq_hw_number_t hw) +-{ +- struct ar71xx_pci_controller *apc = d->host_data; +- +- irq_set_chip_and_handler(irq, &ar71xx_pci_irq_chip, handle_level_irq); +- irq_set_chip_data(irq, apc); +- +- return 0; +-} +- +-static const struct irq_domain_ops ar71xx_pci_domain_ops = { +- .xlate = irq_domain_xlate_onecell, +- .map = ar71xx_pci_irq_map, +-}; +- +-static void ar71xx_pci_irq_init(struct ar71xx_pci_controller *apc) +-{ +- void __iomem *base = ath79_reset_base; +- +- __raw_writel(0, base + AR71XX_RESET_REG_PCI_INT_ENABLE); +- __raw_writel(0, base + AR71XX_RESET_REG_PCI_INT_STATUS); +- +- apc->domain = irq_domain_add_linear(apc->np, AR71XX_PCI_IRQ_COUNT, +- &ar71xx_pci_domain_ops, apc); +- irq_set_chained_handler_and_data(apc->irq, ar71xx_pci_irq_handler, +- apc); +-} +- + static void ar71xx_pci_reset(void) + { + ath79_device_reset_set(AR71XX_RESET_PCI_BUS | AR71XX_RESET_PCI_CORE); +@@ -358,10 +258,6 @@ static int ar71xx_pci_probe(struct platf + if (IS_ERR(apc->cfg_base)) + return PTR_ERR(apc->cfg_base); + +- apc->irq = platform_get_irq(pdev, 0); +- if (apc->irq < 0) +- return -EINVAL; +- + ar71xx_pci_reset(); + + /* setup COMMAND register */ +@@ -372,8 +268,6 @@ static int ar71xx_pci_probe(struct platf + /* clear bus errors */ + ar71xx_pci_check_error(apc, 1); + +- ar71xx_pci_irq_init(apc); +- + apc->np = pdev->dev.of_node; + apc->pci_ctrl.pci_ops = &ar71xx_pci_ops; + apc->pci_ctrl.mem_resource = &apc->mem_res; diff --git a/target/linux/ath79/patches-5.10/0037-missing-registers.patch b/target/linux/ath79/patches-5.10/0037-missing-registers.patch new file mode 100644 index 0000000000..9067e4ca7b --- /dev/null +++ b/target/linux/ath79/patches-5.10/0037-missing-registers.patch @@ -0,0 +1,21 @@ +commit f3ffac90bc7266b7d917616f3233f58e8c08a196 +Author: Christian Lamparter <chunkeey@gmail.com> +Date: Fri Aug 10 23:24:47 2018 +0200 + + ath79: gmac: add parsers for rxd(v)- and tx(d|en)-delay for AR9344 + + Signed-off-by: Christian Lamparter <chunkeey@gmail.com> + +--- a/arch/mips/include/asm/mach-ath79/ar71xx_regs.h ++++ b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h +@@ -1226,6 +1226,10 @@ + #define AR934X_ETH_CFG_RDV_DELAY BIT(16) + #define AR934X_ETH_CFG_RDV_DELAY_MASK 0x3 + #define AR934X_ETH_CFG_RDV_DELAY_SHIFT 16 ++#define AR934X_ETH_CFG_TXD_DELAY_MASK 0x3 ++#define AR934X_ETH_CFG_TXD_DELAY_SHIFT 18 ++#define AR934X_ETH_CFG_TXE_DELAY_MASK 0x3 ++#define AR934X_ETH_CFG_TXE_DELAY_SHIFT 20 + + /* + * QCA953X GMAC Interface diff --git a/target/linux/ath79/patches-5.10/0038-MIPS-ath79-add-missing-QCA955x-GMAC-registers.patch b/target/linux/ath79/patches-5.10/0038-MIPS-ath79-add-missing-QCA955x-GMAC-registers.patch new file mode 100644 index 0000000000..bc09062dc5 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0038-MIPS-ath79-add-missing-QCA955x-GMAC-registers.patch @@ -0,0 +1,90 @@ +From 60efe35257b063ce584968f9f80b437030ce6ba6 Mon Sep 17 00:00:00 2001 +From: David Bauer <mail@david-bauer.net> +Date: Mon, 18 Mar 2019 00:54:06 +0100 +Subject: [PATCH] MIPS: ath79: add missing QCA955x GMAC registers + +This adds missing GMAC register definitions for the Qualcomm Atheros +QCA955X series MIPS SoCs. + +They originate from the platforms U-Boot code and the AVM FRITZ!WLAN +Repeater 450E's GPL tarball. + +Signed-off-by: David Bauer <mail@david-bauer.net> +--- + .../mips/include/asm/mach-ath79/ar71xx_regs.h | 54 +++++++++++++++++++ + 1 file changed, 54 insertions(+) + +--- a/arch/mips/include/asm/mach-ath79/ar71xx_regs.h ++++ b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h +@@ -1246,7 +1246,12 @@ + */ + + #define QCA955X_GMAC_REG_ETH_CFG 0x00 ++#define QCA955X_GMAC_REG_SGMII_RESET 0x14 + #define QCA955X_GMAC_REG_SGMII_SERDES 0x18 ++#define QCA955X_GMAC_REG_MR_AN_CONTROL 0x1c ++#define QCA955X_GMAC_REG_MR_AN_STATUS 0x20 ++#define QCA955X_GMAC_REG_SGMII_CONFIG 0x34 ++#define QCA955X_GMAC_REG_SGMII_DEBUG 0x58 + + #define QCA955X_ETH_CFG_RGMII_EN BIT(0) + #define QCA955X_ETH_CFG_MII_GE0 BIT(1) +@@ -1268,9 +1273,58 @@ + #define QCA955X_ETH_CFG_TXE_DELAY_MASK 0x3 + #define QCA955X_ETH_CFG_TXE_DELAY_SHIFT 20 + ++#define QCA955X_SGMII_RESET_RX_CLK_N_RESET 0 ++#define QCA955X_SGMII_RESET_RX_CLK_N BIT(0) ++#define QCA955X_SGMII_RESET_TX_CLK_N BIT(1) ++#define QCA955X_SGMII_RESET_RX_125M_N BIT(2) ++#define QCA955X_SGMII_RESET_TX_125M_N BIT(3) ++#define QCA955X_SGMII_RESET_HW_RX_125M_N BIT(4) ++ + #define QCA955X_SGMII_SERDES_LOCK_DETECT_STATUS BIT(15) + #define QCA955X_SGMII_SERDES_RES_CALIBRATION_SHIFT 23 + #define QCA955X_SGMII_SERDES_RES_CALIBRATION_MASK 0xf ++ ++#define QCA955X_MR_AN_CONTROL_SPEED_SEL1 BIT(6) ++#define QCA955X_MR_AN_CONTROL_DUPLEX_MODE BIT(8) ++#define QCA955X_MR_AN_CONTROL_RESTART_AN BIT(9) ++#define QCA955X_MR_AN_CONTROL_POWER_DOWN BIT(11) ++#define QCA955X_MR_AN_CONTROL_AN_ENABLE BIT(12) ++#define QCA955X_MR_AN_CONTROL_SPEED_SEL0 BIT(13) ++#define QCA955X_MR_AN_CONTROL_LOOPBACK BIT(14) ++#define QCA955X_MR_AN_CONTROL_PHY_RESET BIT(15) ++ ++#define QCA955X_MR_AN_STATUS_EXT_CAP BIT(0) ++#define QCA955X_MR_AN_STATUS_LINK_UP BIT(2) ++#define QCA955X_MR_AN_STATUS_AN_ABILITY BIT(3) ++#define QCA955X_MR_AN_STATUS_REMOTE_FAULT BIT(4) ++#define QCA955X_MR_AN_STATUS_AN_COMPLETE BIT(5) ++#define QCA955X_MR_AN_STATUS_NO_PREAMBLE BIT(6) ++#define QCA955X_MR_AN_STATUS_BASE_PAGE BIT(7) ++ ++#define QCA955X_SGMII_CONFIG_MODE_CTRL_SHIFT 0 ++#define QCA955X_SGMII_CONFIG_MODE_CTRL_MASK 0x7 ++#define QCA955X_SGMII_CONFIG_ENABLE_SGMII_TX_PAUSE BIT(3) ++#define QCA955X_SGMII_CONFIG_MR_REG4_CHANGED BIT(4) ++#define QCA955X_SGMII_CONFIG_FORCE_SPEED BIT(5) ++#define QCA955X_SGMII_CONFIG_SPEED_SHIFT 6 ++#define QCA955X_SGMII_CONFIG_SPEED_MASK 0xc0 ++#define QCA955X_SGMII_CONFIG_REMOTE_PHY_LOOPBACK BIT(8) ++#define QCA955X_SGMII_CONFIG_NEXT_PAGE_LOADED BIT(9) ++#define QCA955X_SGMII_CONFIG_MDIO_ENABLE BIT(10) ++#define QCA955X_SGMII_CONFIG_MDIO_PULSE BIT(11) ++#define QCA955X_SGMII_CONFIG_MDIO_COMPLETE BIT(12) ++#define QCA955X_SGMII_CONFIG_PRBS_ENABLE BIT(13) ++#define QCA955X_SGMII_CONFIG_BERT_ENABLE BIT(14) ++ ++#define QCA955X_SGMII_DEBUG_TX_STATE_MASK 0xff ++#define QCA955X_SGMII_DEBUG_TX_STATE_SHIFT 0 ++#define QCA955X_SGMII_DEBUG_RX_STATE_MASK 0xff00 ++#define QCA955X_SGMII_DEBUG_RX_STATE_SHIFT 8 ++#define QCA955X_SGMII_DEBUG_RX_SYNC_STATE_MASK 0xff0000 ++#define QCA955X_SGMII_DEBUG_RX_SYNC_STATE_SHIFT 16 ++#define QCA955X_SGMII_DEBUG_ARB_STATE_MASK 0xf000000 ++#define QCA955X_SGMII_DEBUG_ARB_STATE_SHIFT 24 ++ + /* + * QCA956X GMAC Interface + */ diff --git a/target/linux/ath79/patches-5.10/0039-MIPS-ath79-export-UART1-reference-clock.patch b/target/linux/ath79/patches-5.10/0039-MIPS-ath79-export-UART1-reference-clock.patch new file mode 100644 index 0000000000..edf888c7e7 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0039-MIPS-ath79-export-UART1-reference-clock.patch @@ -0,0 +1,52 @@ +--- a/arch/mips/ath79/clock.c ++++ b/arch/mips/ath79/clock.c +@@ -40,6 +40,7 @@ static const char * const clk_names[ATH7 + [ATH79_CLK_AHB] = "ahb", + [ATH79_CLK_REF] = "ref", + [ATH79_CLK_MDIO] = "mdio", ++ [ATH79_CLK_UART1] = "uart1", + }; + + static const char * __init ath79_clk_name(int type) +@@ -344,6 +345,9 @@ static void __init ar934x_clocks_init(vo + if (clk_ctrl & AR934X_PLL_SWITCH_CLOCK_CONTROL_MDIO_CLK_SEL) + ath79_set_clk(ATH79_CLK_MDIO, 100 * 1000 * 1000); + ++ if (clk_ctrl & AR934X_PLL_SWITCH_CLOCK_CONTROL_UART1_CLK_SEL) ++ ath79_set_clk(ATH79_CLK_UART1, 100 * 1000 * 1000); ++ + iounmap(dpll_base); + } + +@@ -649,6 +653,9 @@ static void __init ath79_clocks_init_dt( + if (!clks[ATH79_CLK_MDIO]) + clks[ATH79_CLK_MDIO] = clks[ATH79_CLK_REF]; + ++ if (!clks[ATH79_CLK_UART1]) ++ clks[ATH79_CLK_UART1] = clks[ATH79_CLK_REF]; ++ + if (of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data)) { + pr_err("%pOF: could not register clk provider\n", np); + goto err_iounmap; +--- a/arch/mips/include/asm/mach-ath79/ar71xx_regs.h ++++ b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h +@@ -348,6 +348,7 @@ + #define AR934X_PLL_CPU_DDR_CLK_CTRL_AHBCLK_FROM_DDRPLL BIT(24) + + #define AR934X_PLL_SWITCH_CLOCK_CONTROL_MDIO_CLK_SEL BIT(6) ++#define AR934X_PLL_SWITCH_CLOCK_CONTROL_UART1_CLK_SEL BIT(7) + + #define QCA953X_PLL_CPU_CONFIG_REG 0x00 + #define QCA953X_PLL_DDR_CONFIG_REG 0x04 +--- a/include/dt-bindings/clock/ath79-clk.h ++++ b/include/dt-bindings/clock/ath79-clk.h +@@ -11,7 +11,8 @@ + #define ATH79_CLK_AHB 2 + #define ATH79_CLK_REF 3 + #define ATH79_CLK_MDIO 4 ++#define ATH79_CLK_UART1 5 + +-#define ATH79_CLK_END 5 ++#define ATH79_CLK_END 6 + + #endif /* __DT_BINDINGS_ATH79_CLK_H */ diff --git a/target/linux/ath79/patches-5.10/004-register_gpio_driver_earlier.patch b/target/linux/ath79/patches-5.10/004-register_gpio_driver_earlier.patch new file mode 100644 index 0000000000..fa4b05f724 --- /dev/null +++ b/target/linux/ath79/patches-5.10/004-register_gpio_driver_earlier.patch @@ -0,0 +1,18 @@ +HACK: register the GPIO driver earlier to ensure that gpio_request calls +from mach files succeed. + +--- a/drivers/gpio/gpio-ath79.c ++++ b/drivers/gpio/gpio-ath79.c +@@ -310,7 +310,11 @@ static struct platform_driver ath79_gpio + .probe = ath79_gpio_probe, + }; + +-module_platform_driver(ath79_gpio_driver); ++static int __init ath79_gpio_init(void) ++{ ++ return platform_driver_register(&ath79_gpio_driver); ++} ++postcore_initcall(ath79_gpio_init); + + MODULE_DESCRIPTION("Atheros AR71XX/AR724X/AR913X GPIO API support"); + MODULE_LICENSE("GPL v2"); diff --git a/target/linux/ath79/patches-5.10/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch b/target/linux/ath79/patches-5.10/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch new file mode 100644 index 0000000000..a57ac24f29 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch @@ -0,0 +1,28 @@ +From b142b1beb199f62d47370c98a3dd8e13f792e9c0 Mon Sep 17 00:00:00 2001 +From: David Bauer <mail@david-bauer.net> +Date: Thu, 27 Feb 2020 23:03:20 +0100 +Subject: [PATCH] spi: ath79: remove spi-master setup and cleanup assignment + +This removes the assignment of setup and cleanup functions for the ath79 +target. Assigning the setup-method will lead to 'setup_transfer' not +being assigned in spi_bitbang_init. + +Also drop the redundant cleanup assignment, as this also happens in +spi_bitbang_init. + +Signed-off-by: David Bauer <mail@david-bauer.net> +--- + drivers/spi/spi-ath79.c | 2 -- + 1 file changed, 2 deletions(-) + +--- a/drivers/spi/spi-ath79.c ++++ b/drivers/spi/spi-ath79.c +@@ -152,8 +152,6 @@ static int ath79_spi_probe(struct platfo + + master->use_gpio_descriptors = true; + master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32); +- master->setup = spi_bitbang_setup; +- master->cleanup = spi_bitbang_cleanup; + + sp->bitbang.master = master; + sp->bitbang.chipselect = ath79_spi_chipselect; diff --git a/target/linux/ath79/patches-5.10/0051-spi-ath79-always-call-chipselect-function.patch b/target/linux/ath79/patches-5.10/0051-spi-ath79-always-call-chipselect-function.patch new file mode 100644 index 0000000000..746f9035a6 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0051-spi-ath79-always-call-chipselect-function.patch @@ -0,0 +1,21 @@ +From: David Bauer <mail@david-bauer.net> +Date: Wed, 17 Feb 2021 02:44:55 +0100 +Subject: [PATCH] spi: ath79: always call chipselect function + +api-bitbang has to call the chipselect function on the ath79 SPI driver +in order to communicate with the SPI slave device. + +Fixes commit 4a07b8bcd503 ("spi: bitbang: Make chipselect callback optional") + +Signed-off-by: David Bauer <mail@david-bauer.net> + +--- a/drivers/spi/spi-ath79.c ++++ b/drivers/spi/spi-ath79.c +@@ -152,6 +152,7 @@ static int ath79_spi_probe(struct platfo + + master->use_gpio_descriptors = true; + master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32); ++ master->flags = SPI_MASTER_GPIO_SS; + + sp->bitbang.master = master; + sp->bitbang.chipselect = ath79_spi_chipselect; diff --git a/target/linux/ath79/patches-5.10/0052-mtd-spi-nor-add-block-protection-flags-to-macronix.patch b/target/linux/ath79/patches-5.10/0052-mtd-spi-nor-add-block-protection-flags-to-macronix.patch new file mode 100644 index 0000000000..d416276f0d --- /dev/null +++ b/target/linux/ath79/patches-5.10/0052-mtd-spi-nor-add-block-protection-flags-to-macronix.patch @@ -0,0 +1,26 @@ +From 158f9796335b393980afb8e9796eb8d44106652a Mon Sep 17 00:00:00 2001 +From: David Bauer <mail@david-bauer.net> +Date: Mon, 26 Oct 2020 15:10:47 +0100 +Subject: [PATCH 1/2] mtd: spi-nor: add block protection flags to macronix + +Macronix flash chips support block protection by using BP bits in the +read status register. Add the corresponding flag to indicate block +protection support. + +Otherwise, locked blocks are not unlocked when requested. + +Signed-off-by: David Bauer <mail@david-bauer.net> +--- + drivers/mtd/spi-nor/macronix.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/mtd/spi-nor/macronix.c ++++ b/drivers/mtd/spi-nor/macronix.c +@@ -94,6 +94,7 @@ static const struct flash_info macronix_ + + static void macronix_default_init(struct spi_nor *nor) + { ++ nor->flags |= SNOR_F_HAS_LOCK; + nor->params->quad_enable = spi_nor_sr1_bit6_quad_enable; + nor->params->set_4byte_addr_mode = spi_nor_set_4byte_addr_mode; + nor->flags |= SNOR_F_HAS_LOCK; diff --git a/target/linux/ath79/patches-5.10/0053-mtd-spi-nor-use-4-bit-BP-for-large-Macronix-flash.patch b/target/linux/ath79/patches-5.10/0053-mtd-spi-nor-use-4-bit-BP-for-large-Macronix-flash.patch new file mode 100644 index 0000000000..bb393e52eb --- /dev/null +++ b/target/linux/ath79/patches-5.10/0053-mtd-spi-nor-use-4-bit-BP-for-large-Macronix-flash.patch @@ -0,0 +1,85 @@ +From 59f88b8d4447be809d0b5e7a283290d06848d3bc Mon Sep 17 00:00:00 2001 +From: David Bauer <mail@david-bauer.net> +Date: Sun, 25 Oct 2020 01:14:22 +0200 +Subject: [PATCH 2/2] mtd: spi-nor: use 4 bit BP for large Macronix flash + +Macronix SPI-NOR chips with 128 or more 64k blocks have 4 block +protection bits in their status register. Add the corresponding +flag in order to clear these bits when unloking the flash. + +Otherwise, the flash might not be writable depending on the state the +bootloader left the flash in. + +Fixes commit 62593cf40b23 ("mtd: spi-nor: refactor block protection functions") + +Signed-off-by: David Bauer <mail@david-bauer.net> +--- + drivers/mtd/spi-nor/macronix.c | 31 ++++++++++++++++++------------- + 1 file changed, 18 insertions(+), 13 deletions(-) + +--- a/drivers/mtd/spi-nor/macronix.c ++++ b/drivers/mtd/spi-nor/macronix.c +@@ -50,8 +50,8 @@ static const struct flash_info macronix_ + { "mx25u4035", INFO(0xc22533, 0, 64 * 1024, 8, SECT_4K) }, + { "mx25u8035", INFO(0xc22534, 0, 64 * 1024, 16, SECT_4K) }, + { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) }, +- { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, SECT_4K) }, +- { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, ++ { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_4BIT_BP) }, ++ { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, SPI_NOR_4BIT_BP) }, + { "mx25r1635f", INFO(0xc22815, 0, 64 * 1024, 32, + SECT_4K | SPI_NOR_DUAL_READ | + SPI_NOR_QUAD_READ) }, +@@ -60,36 +60,41 @@ static const struct flash_info macronix_ + SPI_NOR_QUAD_READ) }, + { "mx25u12835f", INFO(0xc22538, 0, 64 * 1024, 256, + SECT_4K | SPI_NOR_DUAL_READ | +- SPI_NOR_QUAD_READ) }, ++ SPI_NOR_QUAD_READ | SPI_NOR_4BIT_BP) }, + { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, +- SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) ++ SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | ++ SPI_NOR_4BIT_BP) + .fixups = &mx25l25635_fixups }, + { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, +- SECT_4K | SPI_NOR_4B_OPCODES) }, ++ SECT_4K | SPI_NOR_4B_OPCODES | ++ SPI_NOR_4BIT_BP) }, + { "mx25u51245g", INFO(0xc2253a, 0, 64 * 1024, 1024, + SECT_4K | SPI_NOR_DUAL_READ | +- SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, ++ SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | ++ SPI_NOR_4BIT_BP) }, + { "mx25v8035f", INFO(0xc22314, 0, 64 * 1024, 16, + SECT_4K | SPI_NOR_DUAL_READ | + SPI_NOR_QUAD_READ) }, +- { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) }, ++ { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, SPI_NOR_4BIT_BP) }, + { "mx25l51245g", INFO(0xc2201a, 0, 64 * 1024, 1024, + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | +- SPI_NOR_4B_OPCODES) }, ++ SPI_NOR_4B_OPCODES | SPI_NOR_4BIT_BP) }, + { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, + SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | +- SPI_NOR_4B_OPCODES) }, ++ SPI_NOR_4B_OPCODES | SPI_NOR_4BIT_BP) }, + { "mx66u51235f", INFO(0xc2253a, 0, 64 * 1024, 1024, + SECT_4K | SPI_NOR_DUAL_READ | +- SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, ++ SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | ++ SPI_NOR_4BIT_BP) }, + { "mx66l1g45g", INFO(0xc2201b, 0, 64 * 1024, 2048, + SECT_4K | SPI_NOR_DUAL_READ | +- SPI_NOR_QUAD_READ) }, ++ SPI_NOR_QUAD_READ | SPI_NOR_4BIT_BP) }, + { "mx66l1g55g", INFO(0xc2261b, 0, 64 * 1024, 2048, +- SPI_NOR_QUAD_READ) }, ++ SPI_NOR_QUAD_READ | SPI_NOR_4BIT_BP) }, + { "mx66u2g45g", INFO(0xc2253c, 0, 64 * 1024, 4096, + SECT_4K | SPI_NOR_DUAL_READ | +- SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, ++ SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | ++ SPI_NOR_4BIT_BP) }, + }; + + static void macronix_default_init(struct spi_nor *nor) diff --git a/target/linux/ath79/patches-5.10/0054-spi-always-write-cs.patch b/target/linux/ath79/patches-5.10/0054-spi-always-write-cs.patch new file mode 100644 index 0000000000..1e461cee0a --- /dev/null +++ b/target/linux/ath79/patches-5.10/0054-spi-always-write-cs.patch @@ -0,0 +1,31 @@ +Upstream commit d40f0b6f2e21 ("spi: Avoid settingthe chip select if +we don't need to") causes the SPI CS only to be asserted once and not +if it's state stays the same. + +This seems to cause problems with the SPI on the AR724x and the AR913x +(but not the AR71xx). AR934x and subsequent chips do not look affected. + +ToDo: + - Analyze if this is a hardware bug or a bug in the software. + - Send a cleaned up patch upstream. + +Signed-off-by: David Bauer <mail@david-bauer.net> + +--- a/drivers/spi/spi.c ++++ b/drivers/spi/spi.c +@@ -791,6 +791,7 @@ static void spi_set_cs(struct spi_device + { + bool enable1 = enable; + ++#if 0 + /* + * Avoid calling into the driver (or doing delays) if the chip select + * isn't actually changing from the last time this was called. +@@ -801,6 +802,7 @@ static void spi_set_cs(struct spi_device + + spi->controller->last_cs_enable = enable; + spi->controller->last_cs_mode_high = spi->mode & SPI_CS_HIGH; ++#endif + + if (!spi->controller->set_cs_timing) { + if (enable1) diff --git a/target/linux/ath79/patches-5.10/0062-MIPS-pci-ar724x-add-QCA9550-reset-sequence.patch b/target/linux/ath79/patches-5.10/0062-MIPS-pci-ar724x-add-QCA9550-reset-sequence.patch new file mode 100644 index 0000000000..13955c62a2 --- /dev/null +++ b/target/linux/ath79/patches-5.10/0062-MIPS-pci-ar724x-add-QCA9550-reset-sequence.patch @@ -0,0 +1,130 @@ +From: David Bauer <mail@david-bauer.net> +Date: Sat, 11 Apr 2020 14:03:12 +0200 +Subject: MIPS: pci-ar724x: add QCA9550 reset sequence + +The QCA9550 family of SoCs have a slightly different reset +sequence compared to older chips. + +Normally the bootloader performs this sequence, however +some bootloader implementation expect the operating system +to clear the reset. + +Also get the resets from OF to support handling of the second +PCIe root-complex on the QCA9558. + +Signed-off-by: David Bauer <mail@david-bauer.net> + +--- a/arch/mips/include/asm/mach-ath79/ar71xx_regs.h ++++ b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h +@@ -391,6 +391,7 @@ + #define QCA955X_PLL_CPU_CONFIG_REG 0x00 + #define QCA955X_PLL_DDR_CONFIG_REG 0x04 + #define QCA955X_PLL_CLK_CTRL_REG 0x08 ++#define QCA955X_PLL_PCIE_CONFIG_REG 0x0c + #define QCA955X_PLL_ETH_XMII_CONTROL_REG 0x28 + #define QCA955X_PLL_ETH_SGMII_CONTROL_REG 0x48 + #define QCA955X_PLL_ETH_SGMII_SERDES_REG 0x4c +@@ -476,6 +477,9 @@ + #define QCA956X_PLL_CLK_CTRL_CPU_DDRCLK_FROM_CPUPLL BIT(21) + #define QCA956X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL BIT(24) + ++#define QCA955X_PLL_PCIE_CONFIG_PLL_PWD BIT(30) ++#define QCA955X_PLL_PCIE_CONFIG_PLL_BYPASS BIT(16) ++ + #define QCA956X_PLL_SWITCH_CLOCK_SPARE_I2C_CLK_SELB BIT(5) + #define QCA956X_PLL_SWITCH_CLOCK_SPARE_MDIO_CLK_SEL0_1 BIT(6) + #define QCA956X_PLL_SWITCH_CLOCK_SPARE_UART1_CLK_SEL BIT(7) +--- a/arch/mips/pci/pci-ar724x.c ++++ b/arch/mips/pci/pci-ar724x.c +@@ -8,6 +8,7 @@ + + #include <linux/irq.h> + #include <linux/pci.h> ++#include <linux/reset.h> + #include <linux/init.h> + #include <linux/delay.h> + #include <linux/platform_device.h> +@@ -55,6 +56,9 @@ struct ar724x_pci_controller { + struct irq_domain *domain; + struct resource io_res; + struct resource mem_res; ++ ++ struct reset_control *hc_reset; ++ struct reset_control *phy_reset; + }; + + static struct irq_chip ar724x_pci_irq_chip; +@@ -340,18 +344,30 @@ static void ar724x_pci_hw_init(struct ar + int wait = 0; + + /* deassert PCIe host controller and PCIe PHY reset */ +- ath79_device_reset_clear(AR724X_RESET_PCIE); +- ath79_device_reset_clear(AR724X_RESET_PCIE_PHY); ++ reset_control_deassert(apc->hc_reset); ++ reset_control_deassert(apc->phy_reset); + +- /* remove the reset of the PCIE PLL */ +- ppl = ath79_pll_rr(AR724X_PLL_REG_PCIE_CONFIG); +- ppl &= ~AR724X_PLL_REG_PCIE_CONFIG_PPL_RESET; +- ath79_pll_wr(AR724X_PLL_REG_PCIE_CONFIG, ppl); +- +- /* deassert bypass for the PCIE PLL */ +- ppl = ath79_pll_rr(AR724X_PLL_REG_PCIE_CONFIG); +- ppl &= ~AR724X_PLL_REG_PCIE_CONFIG_PPL_BYPASS; +- ath79_pll_wr(AR724X_PLL_REG_PCIE_CONFIG, ppl); ++ if (of_device_is_compatible(apc->np, "qcom,qca9550-pci")) { ++ /* remove the reset of the PCIE PLL */ ++ ppl = ath79_pll_rr(QCA955X_PLL_PCIE_CONFIG_REG); ++ ppl &= ~QCA955X_PLL_PCIE_CONFIG_PLL_PWD; ++ ath79_pll_wr(QCA955X_PLL_PCIE_CONFIG_REG, ppl); ++ ++ /* deassert bypass for the PCIE PLL */ ++ ppl = ath79_pll_rr(QCA955X_PLL_PCIE_CONFIG_REG); ++ ppl &= ~QCA955X_PLL_PCIE_CONFIG_PLL_BYPASS; ++ ath79_pll_wr(QCA955X_PLL_PCIE_CONFIG_REG, ppl); ++ } else { ++ /* remove the reset of the PCIE PLL */ ++ ppl = ath79_pll_rr(AR724X_PLL_REG_PCIE_CONFIG); ++ ppl &= ~AR724X_PLL_REG_PCIE_CONFIG_PPL_RESET; ++ ath79_pll_wr(AR724X_PLL_REG_PCIE_CONFIG, ppl); ++ ++ /* deassert bypass for the PCIE PLL */ ++ ppl = ath79_pll_rr(AR724X_PLL_REG_PCIE_CONFIG); ++ ppl &= ~AR724X_PLL_REG_PCIE_CONFIG_PPL_BYPASS; ++ ath79_pll_wr(AR724X_PLL_REG_PCIE_CONFIG, ppl); ++ } + + /* set PCIE Application Control to ready */ + app = __raw_readl(apc->ctrl_base + AR724X_PCI_REG_APP); +@@ -399,6 +415,14 @@ static int ar724x_pci_probe(struct platf + if (apc->irq < 0) + return -EINVAL; + ++ apc->hc_reset = devm_reset_control_get_exclusive(&pdev->dev, "hc"); ++ if (IS_ERR(apc->hc_reset)) ++ return PTR_ERR(apc->hc_reset); ++ ++ apc->phy_reset = devm_reset_control_get_exclusive(&pdev->dev, "phy"); ++ if (IS_ERR(apc->phy_reset)) ++ return PTR_ERR(apc->phy_reset); ++ + apc->np = pdev->dev.of_node; + apc->pci_controller.pci_ops = &ar724x_pci_ops; + apc->pci_controller.io_resource = &apc->io_res; +@@ -409,7 +433,7 @@ static int ar724x_pci_probe(struct platf + * Do the full PCIE Root Complex Initialization Sequence if the PCIe + * host controller is in reset. + */ +- if (ath79_reset_rr(AR724X_RESET_REG_RESET_MODULE) & AR724X_RESET_PCIE) ++ if (reset_control_status(apc->hc_reset)) + ar724x_pci_hw_init(apc); + + apc->link_up = ar724x_pci_check_link(apc); +@@ -427,6 +451,7 @@ static int ar724x_pci_probe(struct platf + + static const struct of_device_id ar724x_pci_ids[] = { + { .compatible = "qcom,ar7240-pci" }, ++ { .compatible = "qcom,qca9550-pci" }, + {}, + }; + diff --git a/target/linux/ath79/patches-5.10/404-mtd-cybertan-trx-parser.patch b/target/linux/ath79/patches-5.10/404-mtd-cybertan-trx-parser.patch new file mode 100644 index 0000000000..1ebf87c610 --- /dev/null +++ b/target/linux/ath79/patches-5.10/404-mtd-cybertan-trx-parser.patch @@ -0,0 +1,27 @@ +--- a/drivers/mtd/parsers/Makefile ++++ b/drivers/mtd/parsers/Makefile +@@ -5,6 +5,7 @@ obj-$(CONFIG_MTD_BCM63XX_PARTS) += bcm6 + obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o + obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o + obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o ++obj-$(CONFIG_MTD_PARSER_CYBERTAN) += parser_cybertan.o + obj-$(CONFIG_MTD_PARSER_IMAGETAG) += parser_imagetag.o + obj-$(CONFIG_MTD_AFS_PARTS) += afs.o + obj-$(CONFIG_MTD_PARSER_TRX) += parser_trx.o +--- a/drivers/mtd/parsers/Kconfig ++++ b/drivers/mtd/parsers/Kconfig +@@ -83,6 +83,14 @@ config MTD_OF_PARTS + flash memory node, as described in + Documentation/devicetree/bindings/mtd/partition.txt. + ++config MTD_PARSER_CYBERTAN ++ tristate "Parser for Cybertan format partitions" ++ depends on MTD && (ATH79 || COMPILE_TEST) ++ help ++ Cybertan has a proprietory header than encompasses a Broadcom trx ++ header. This driver will parse the header and take care of the ++ special offsets that result in the extra headers. ++ + config MTD_PARSER_IMAGETAG + tristate "Parser for BCM963XX Image Tag format partitions" + depends on BCM63XX || BMIPS_GENERIC || COMPILE_TEST diff --git a/target/linux/ath79/patches-5.10/408-mtd-redboot_partition_scan.patch b/target/linux/ath79/patches-5.10/408-mtd-redboot_partition_scan.patch new file mode 100644 index 0000000000..8f3ee32f57 --- /dev/null +++ b/target/linux/ath79/patches-5.10/408-mtd-redboot_partition_scan.patch @@ -0,0 +1,44 @@ +--- a/drivers/mtd/parsers/redboot.c ++++ b/drivers/mtd/parsers/redboot.c +@@ -85,12 +85,18 @@ static int parse_redboot_partitions(stru + + parse_redboot_of(master); + ++ buf = vmalloc(master->erasesize); ++ if (!buf) ++ return -ENOMEM; ++ ++ restart: + if ( directory < 0 ) { + offset = master->size + directory * master->erasesize; + while (mtd_block_isbad(master, offset)) { + if (!offset) { + nogood: + printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n"); ++ vfree(buf); + return -EIO; + } + offset -= master->erasesize; +@@ -103,10 +109,6 @@ static int parse_redboot_partitions(stru + goto nogood; + } + } +- buf = vmalloc(master->erasesize); +- +- if (!buf) +- return -ENOMEM; + + printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n", + master->name, offset); +@@ -179,6 +181,11 @@ static int parse_redboot_partitions(stru + } + if (i == numslots) { + /* Didn't find it */ ++ if (offset + master->erasesize < master->size) { ++ /* not at the end of the flash yet, maybe next block :) */ ++ directory++; ++ goto restart; ++ } + printk(KERN_NOTICE "No RedBoot partition table detected in %s\n", + master->name); + ret = 0; diff --git a/target/linux/ath79/patches-5.10/410-spi-ath79-Implement-the-spi_mem-interface.patch b/target/linux/ath79/patches-5.10/410-spi-ath79-Implement-the-spi_mem-interface.patch new file mode 100644 index 0000000000..2a6b9857fb --- /dev/null +++ b/target/linux/ath79/patches-5.10/410-spi-ath79-Implement-the-spi_mem-interface.patch @@ -0,0 +1,68 @@ +From 8d8cdb4a6ccee5b62cc0dc64651c3946364514dc Mon Sep 17 00:00:00 2001 +From: Luiz Angelo Daros de Luca <luizluca@gmail.com> +Date: Mon, 10 Feb 2020 16:11:27 -0300 +Subject: [PATCH] spi: ath79: Implement the spi_mem interface + +Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> +--- + drivers/spi/spi-ath79.c | 35 +++++++++++++++++++++++++++++++++++ + 1 file changed, 35 insertions(+) + +--- a/drivers/spi/spi-ath79.c ++++ b/drivers/spi/spi-ath79.c +@@ -15,6 +15,7 @@ + #include <linux/platform_device.h> + #include <linux/io.h> + #include <linux/spi/spi.h> ++#include <linux/spi/spi-mem.h> + #include <linux/spi/spi_bitbang.h> + #include <linux/bitops.h> + #include <linux/clk.h> +@@ -133,6 +134,39 @@ static u32 ath79_spi_txrx_mode0(struct s + return ath79_spi_rr(sp, AR71XX_SPI_REG_RDS); + } + ++static int ath79_exec_mem_op(struct spi_mem *mem, ++ const struct spi_mem_op *op) ++{ ++ struct ath79_spi *sp = ath79_spidev_to_sp(mem->spi); ++ ++ /* Ensures that reading is performed on device connected ++ to hardware cs0 */ ++ if (mem->spi->chip_select || mem->spi->cs_gpiod) ++ return -ENOTSUPP; ++ ++ /* Only use for fast-read op. */ ++ if (op->cmd.opcode != 0x0b || op->data.dir != SPI_MEM_DATA_IN || ++ op->addr.nbytes != 3 || op->dummy.nbytes != 1) ++ return -ENOTSUPP; ++ ++ /* disable GPIO mode */ ++ ath79_spi_wr(sp, AR71XX_SPI_REG_FS, 0); ++ ++ memcpy_fromio(op->data.buf.in, sp->base + op->addr.val, op->data.nbytes); ++ ++ /* enable GPIO mode */ ++ ath79_spi_wr(sp, AR71XX_SPI_REG_FS, AR71XX_SPI_FS_GPIO); ++ ++ /* restore IOC register */ ++ ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base); ++ ++ return 0; ++} ++ ++static const struct spi_controller_mem_ops ath79_mem_ops = { ++ .exec_op = ath79_exec_mem_op, ++}; ++ + static int ath79_spi_probe(struct platform_device *pdev) + { + struct spi_master *master; +@@ -163,6 +197,7 @@ static int ath79_spi_probe(struct platfo + ret = PTR_ERR(sp->base); + goto err_put_master; + } ++ master->mem_ops = &ath79_mem_ops; + + sp->clk = devm_clk_get(&pdev->dev, "ahb"); + if (IS_ERR(sp->clk)) { diff --git a/target/linux/ath79/patches-5.10/420-net-use-downstream-ag71xx.patch b/target/linux/ath79/patches-5.10/420-net-use-downstream-ag71xx.patch new file mode 100644 index 0000000000..7ce3f0d29c --- /dev/null +++ b/target/linux/ath79/patches-5.10/420-net-use-downstream-ag71xx.patch @@ -0,0 +1,28 @@ +--- a/drivers/net/ethernet/atheros/Kconfig ++++ b/drivers/net/ethernet/atheros/Kconfig +@@ -17,13 +17,7 @@ config NET_VENDOR_ATHEROS + + if NET_VENDOR_ATHEROS + +-config AG71XX +- tristate "Atheros AR7XXX/AR9XXX built-in ethernet mac support" +- depends on ATH79 +- select PHYLINK +- help +- If you wish to compile a kernel for AR7XXX/91XXX and enable +- ethernet support, then you should always answer Y to this. ++source "drivers/net/ethernet/atheros/ag71xx/Kconfig" + + config ATL2 + tristate "Atheros L2 Fast Ethernet support" +--- a/drivers/net/ethernet/atheros/Makefile ++++ b/drivers/net/ethernet/atheros/Makefile +@@ -3,7 +3,7 @@ + # Makefile for the Atheros network device drivers. + # + +-obj-$(CONFIG_AG71XX) += ag71xx.o ++obj-$(CONFIG_AG71XX) += ag71xx/ + obj-$(CONFIG_ATL1) += atlx/ + obj-$(CONFIG_ATL2) += atlx/ + obj-$(CONFIG_ATL1E) += atl1e/ diff --git a/target/linux/ath79/patches-5.10/425-at803x-allow-sgmii-aneg-override.patch b/target/linux/ath79/patches-5.10/425-at803x-allow-sgmii-aneg-override.patch new file mode 100644 index 0000000000..396b1ee7a2 --- /dev/null +++ b/target/linux/ath79/patches-5.10/425-at803x-allow-sgmii-aneg-override.patch @@ -0,0 +1,16 @@ +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -383,6 +383,13 @@ static int at803x_aneg_done(struct phy_d + if (!(phy_read(phydev, AT803X_PSSR) & AT803X_PSSR_MR_AN_COMPLETE)) { + phydev_warn(phydev, "803x_aneg_done: SGMII link is not ok\n"); + aneg_done = 0; ++#ifdef CONFIG_OF_MDIO ++ if (phydev->mdio.dev.of_node && ++ of_property_read_bool(phydev->mdio.dev.of_node, ++ "at803x-override-sgmii-link-check")) { ++ aneg_done = 1; ++ } ++#endif + } + /* switch back to copper page */ + phy_write(phydev, AT803X_REG_CHIP_CONFIG, ccr | AT803X_BT_BX_REG_SEL); diff --git a/target/linux/ath79/patches-5.10/430-drivers-link-spi-before-mtd.patch b/target/linux/ath79/patches-5.10/430-drivers-link-spi-before-mtd.patch new file mode 100644 index 0000000000..4c6558db90 --- /dev/null +++ b/target/linux/ath79/patches-5.10/430-drivers-link-spi-before-mtd.patch @@ -0,0 +1,12 @@ +--- a/drivers/Makefile ++++ b/drivers/Makefile +@@ -80,8 +80,8 @@ obj-y += scsi/ + obj-y += nvme/ + obj-$(CONFIG_ATA) += ata/ + obj-$(CONFIG_TARGET_CORE) += target/ +-obj-$(CONFIG_MTD) += mtd/ + obj-$(CONFIG_SPI) += spi/ ++obj-$(CONFIG_MTD) += mtd/ + obj-$(CONFIG_SPMI) += spmi/ + obj-$(CONFIG_HSI) += hsi/ + obj-$(CONFIG_SLIMBUS) += slimbus/ diff --git a/target/linux/ath79/patches-5.10/440-mtd-ar934x-nand-driver.patch b/target/linux/ath79/patches-5.10/440-mtd-ar934x-nand-driver.patch new file mode 100644 index 0000000000..1e2d573ebf --- /dev/null +++ b/target/linux/ath79/patches-5.10/440-mtd-ar934x-nand-driver.patch @@ -0,0 +1,25 @@ +--- a/drivers/mtd/nand/raw/Kconfig ++++ b/drivers/mtd/nand/raw/Kconfig +@@ -556,4 +556,12 @@ config MTD_NAND_DISKONCHIP_BBTWRITE + load time (assuming you build diskonchip as a module) with the module + parameter "inftl_bbt_write=1". + ++config MTD_NAND_AR934X ++ tristate "Support for NAND controller on Qualcomm Atheros AR934x/QCA955x SoCs" ++ depends on ATH79 || COMPILE_TEST ++ depends on HAS_IOMEM ++ help ++ Enables support for NAND controller on Qualcomm Atheros SoCs. ++ This controller is found on AR934x and QCA955x SoCs. ++ + endif # MTD_RAW_NAND +--- a/drivers/mtd/nand/raw/Makefile ++++ b/drivers/mtd/nand/raw/Makefile +@@ -58,6 +58,7 @@ obj-$(CONFIG_MTD_NAND_STM32_FMC2) += stm + obj-$(CONFIG_MTD_NAND_MESON) += meson_nand.o + obj-$(CONFIG_MTD_NAND_CADENCE) += cadence-nand-controller.o + obj-$(CONFIG_MTD_NAND_ARASAN) += arasan-nand-controller.o ++obj-$(CONFIG_MTD_NAND_AR934X) += ar934x_nand.o + + nand-objs := nand_base.o nand_legacy.o nand_bbt.o nand_timings.o nand_ids.o + nand-objs += nand_onfi.o diff --git a/target/linux/ath79/patches-5.10/470-MIPS-ath79-swizzle-pci-address-for-ar71xx.patch b/target/linux/ath79/patches-5.10/470-MIPS-ath79-swizzle-pci-address-for-ar71xx.patch new file mode 100644 index 0000000000..924faec509 --- /dev/null +++ b/target/linux/ath79/patches-5.10/470-MIPS-ath79-swizzle-pci-address-for-ar71xx.patch @@ -0,0 +1,98 @@ +--- /dev/null ++++ b/arch/mips/include/asm/mach-ath79/mangle-port.h +@@ -0,0 +1,37 @@ ++/* ++ * Copyright (C) 2012 Gabor Juhos <juhosg@openwrt.org> ++ * ++ * This file was derived from: inlude/asm-mips/mach-generic/mangle-port.h ++ * Copyright (C) 2003, 2004 Ralf Baechle ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ */ ++ ++#ifndef __ASM_MACH_ATH79_MANGLE_PORT_H ++#define __ASM_MACH_ATH79_MANGLE_PORT_H ++ ++#ifdef CONFIG_PCI_AR71XX ++extern unsigned long (ath79_pci_swizzle_b)(unsigned long port); ++extern unsigned long (ath79_pci_swizzle_w)(unsigned long port); ++#else ++#define ath79_pci_swizzle_b(port) (port) ++#define ath79_pci_swizzle_w(port) (port) ++#endif ++ ++#define __swizzle_addr_b(port) ath79_pci_swizzle_b(port) ++#define __swizzle_addr_w(port) ath79_pci_swizzle_w(port) ++#define __swizzle_addr_l(port) (port) ++#define __swizzle_addr_q(port) (port) ++ ++# define ioswabb(a, x) (x) ++# define __mem_ioswabb(a, x) (x) ++# define ioswabw(a, x) (x) ++# define __mem_ioswabw(a, x) cpu_to_le16(x) ++# define ioswabl(a, x) (x) ++# define __mem_ioswabl(a, x) cpu_to_le32(x) ++# define ioswabq(a, x) (x) ++# define __mem_ioswabq(a, x) cpu_to_le64(x) ++ ++#endif /* __ASM_MACH_ATH79_MANGLE_PORT_H */ +--- a/arch/mips/pci/pci-ar71xx.c ++++ b/arch/mips/pci/pci-ar71xx.c +@@ -68,6 +68,45 @@ static const u32 ar71xx_pci_read_mask[8] + 0, 0xff, 0xffff, 0, 0xffffffff, 0, 0, 0 + }; + ++static unsigned long (*__ath79_pci_swizzle_b)(unsigned long port); ++static unsigned long (*__ath79_pci_swizzle_w)(unsigned long port); ++ ++static inline bool ar71xx_is_pci_addr(unsigned long port) ++{ ++ unsigned long phys = CPHYSADDR(port); ++ ++ return (phys >= AR71XX_PCI_MEM_BASE && ++ phys < AR71XX_PCI_MEM_BASE + AR71XX_PCI_MEM_SIZE); ++} ++ ++static unsigned long ar71xx_pci_swizzle_b(unsigned long port) ++{ ++ return ar71xx_is_pci_addr(port) ? port ^ 3 : port; ++} ++ ++static unsigned long ar71xx_pci_swizzle_w(unsigned long port) ++{ ++ return ar71xx_is_pci_addr(port) ? port ^ 2 : port; ++} ++ ++unsigned long ath79_pci_swizzle_b(unsigned long port) ++{ ++ if (__ath79_pci_swizzle_b) ++ return __ath79_pci_swizzle_b(port); ++ ++ return port; ++} ++EXPORT_SYMBOL(ath79_pci_swizzle_b); ++ ++unsigned long ath79_pci_swizzle_w(unsigned long port) ++{ ++ if (__ath79_pci_swizzle_w) ++ return __ath79_pci_swizzle_w(port); ++ ++ return port; ++} ++EXPORT_SYMBOL(ath79_pci_swizzle_w); ++ + static inline u32 ar71xx_pci_get_ble(int where, int size, int local) + { + u32 t; +@@ -276,6 +315,9 @@ static int ar71xx_pci_probe(struct platf + + register_pci_controller(&apc->pci_ctrl); + ++ __ath79_pci_swizzle_b = ar71xx_pci_swizzle_b; ++ __ath79_pci_swizzle_w = ar71xx_pci_swizzle_w; ++ + return 0; + } + diff --git a/target/linux/ath79/patches-5.10/900-mdio_bitbang_ignore_ta_value.patch b/target/linux/ath79/patches-5.10/900-mdio_bitbang_ignore_ta_value.patch new file mode 100644 index 0000000000..928f241abd --- /dev/null +++ b/target/linux/ath79/patches-5.10/900-mdio_bitbang_ignore_ta_value.patch @@ -0,0 +1,32 @@ +--- a/drivers/net/mdio/mdio-bitbang.c ++++ b/drivers/net/mdio/mdio-bitbang.c +@@ -152,7 +152,7 @@ static int mdiobb_cmd_addr(struct mdiobb + static int mdiobb_read(struct mii_bus *bus, int phy, int reg) + { + struct mdiobb_ctrl *ctrl = bus->priv; +- int ret, i; ++ int ret; + + if (reg & MII_ADDR_C45) { + reg = mdiobb_cmd_addr(ctrl, phy, reg); +@@ -162,19 +162,7 @@ static int mdiobb_read(struct mii_bus *b + + ctrl->ops->set_mdio_dir(ctrl, 0); + +- /* check the turnaround bit: the PHY should be driving it to zero, if this +- * PHY is listed in phy_ignore_ta_mask as having broken TA, skip that +- */ +- if (mdiobb_get_bit(ctrl) != 0 && +- !(bus->phy_ignore_ta_mask & (1 << phy))) { +- /* PHY didn't drive TA low -- flush any bits it +- * may be trying to send. +- */ +- for (i = 0; i < 32; i++) +- mdiobb_get_bit(ctrl); +- +- return 0xffff; +- } ++ mdiobb_get_bit(ctrl); + + ret = mdiobb_get_num(ctrl, 16); + mdiobb_get_bit(ctrl); diff --git a/target/linux/ath79/patches-5.10/901-phy-mdio-bitbang-prevent-rescheduling-during-command.patch b/target/linux/ath79/patches-5.10/901-phy-mdio-bitbang-prevent-rescheduling-during-command.patch new file mode 100644 index 0000000000..5b3260eecb --- /dev/null +++ b/target/linux/ath79/patches-5.10/901-phy-mdio-bitbang-prevent-rescheduling-during-command.patch @@ -0,0 +1,61 @@ +From 66e584435ac0de6e0abeb6d7166fe4fe25d6bb73 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 16 Jun 2015 13:15:08 +0200 +Subject: [PATCH] phy/mdio-bitbang: prevent rescheduling during command + +It seems some phys have some maximum timings for accessing the MDIO line, +resulting in bit errors under cpu stress. Prevent this from happening by +disabling interrupts when sending commands. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + drivers/net/mdio/mdio-bitbang.c | 9 +++++++++ + 1 file changed, 9 insertions(+) + +--- a/drivers/net/mdio/mdio-bitbang.c ++++ b/drivers/net/mdio/mdio-bitbang.c +@@ -14,6 +14,7 @@ + * Vitaly Bordug <vbordug@ru.mvista.com> + */ + ++#include <linux/irqflags.h> + #include <linux/module.h> + #include <linux/mdio-bitbang.h> + #include <linux/types.h> +@@ -153,7 +154,9 @@ static int mdiobb_read(struct mii_bus *b + { + struct mdiobb_ctrl *ctrl = bus->priv; + int ret; ++ unsigned long flags; + ++ local_irq_save(flags); + if (reg & MII_ADDR_C45) { + reg = mdiobb_cmd_addr(ctrl, phy, reg); + mdiobb_cmd(ctrl, MDIO_C45_READ, phy, reg); +@@ -166,13 +169,17 @@ static int mdiobb_read(struct mii_bus *b + + ret = mdiobb_get_num(ctrl, 16); + mdiobb_get_bit(ctrl); ++ local_irq_restore(flags); ++ + return ret; + } + + static int mdiobb_write(struct mii_bus *bus, int phy, int reg, u16 val) + { + struct mdiobb_ctrl *ctrl = bus->priv; ++ unsigned long flags; + ++ local_irq_save(flags); + if (reg & MII_ADDR_C45) { + reg = mdiobb_cmd_addr(ctrl, phy, reg); + mdiobb_cmd(ctrl, MDIO_C45_WRITE, phy, reg); +@@ -187,6 +194,8 @@ static int mdiobb_write(struct mii_bus * + + ctrl->ops->set_mdio_dir(ctrl, 0); + mdiobb_get_bit(ctrl); ++ local_irq_restore(flags); ++ + return 0; + } + diff --git a/target/linux/ath79/patches-5.10/910-unaligned_access_hacks.patch b/target/linux/ath79/patches-5.10/910-unaligned_access_hacks.patch new file mode 100644 index 0000000000..2440fbbb73 --- /dev/null +++ b/target/linux/ath79/patches-5.10/910-unaligned_access_hacks.patch @@ -0,0 +1,869 @@ +--- a/arch/mips/include/asm/checksum.h ++++ b/arch/mips/include/asm/checksum.h +@@ -134,26 +134,30 @@ static inline __sum16 ip_fast_csum(const + const unsigned int *stop = word + ihl; + unsigned int csum; + int carry; ++ unsigned int w; + +- csum = word[0]; +- csum += word[1]; +- carry = (csum < word[1]); ++ csum = net_hdr_word(word++); ++ ++ w = net_hdr_word(word++); ++ csum += w; ++ carry = (csum < w); + csum += carry; + +- csum += word[2]; +- carry = (csum < word[2]); ++ w = net_hdr_word(word++); ++ csum += w; ++ carry = (csum < w); + csum += carry; + +- csum += word[3]; +- carry = (csum < word[3]); ++ w = net_hdr_word(word++); ++ csum += w; ++ carry = (csum < w); + csum += carry; + +- word += 4; + do { +- csum += *word; +- carry = (csum < *word); ++ w = net_hdr_word(word++); ++ csum += w; ++ carry = (csum < w); + csum += carry; +- word++; + } while (word != stop); + + return csum_fold(csum); +@@ -214,73 +218,6 @@ static inline __sum16 ip_compute_csum(co + return csum_fold(csum_partial(buff, len, 0)); + } + +-#define _HAVE_ARCH_IPV6_CSUM +-static __inline__ __sum16 csum_ipv6_magic(const struct in6_addr *saddr, +- const struct in6_addr *daddr, +- __u32 len, __u8 proto, +- __wsum sum) +-{ +- __wsum tmp; +- +- __asm__( +- " .set push # csum_ipv6_magic\n" +- " .set noreorder \n" +- " .set noat \n" +- " addu %0, %5 # proto (long in network byte order)\n" +- " sltu $1, %0, %5 \n" +- " addu %0, $1 \n" +- +- " addu %0, %6 # csum\n" +- " sltu $1, %0, %6 \n" +- " lw %1, 0(%2) # four words source address\n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " lw %1, 4(%2) \n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " lw %1, 8(%2) \n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " lw %1, 12(%2) \n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " lw %1, 0(%3) \n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " lw %1, 4(%3) \n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " lw %1, 8(%3) \n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " lw %1, 12(%3) \n" +- " addu %0, $1 \n" +- " addu %0, %1 \n" +- " sltu $1, %0, %1 \n" +- +- " addu %0, $1 # Add final carry\n" +- " .set pop" +- : "=&r" (sum), "=&r" (tmp) +- : "r" (saddr), "r" (daddr), +- "0" (htonl(len)), "r" (htonl(proto)), "r" (sum)); +- +- return csum_fold(sum); +-} +- + #include <asm-generic/checksum.h> + #endif /* CONFIG_GENERIC_CSUM */ + +--- a/include/uapi/linux/ip.h ++++ b/include/uapi/linux/ip.h +@@ -103,7 +103,7 @@ struct iphdr { + __be32 saddr; + __be32 daddr; + /*The options start here. */ +-}; ++} __attribute__((packed, aligned(2))); + + + struct ip_auth_hdr { +--- a/include/uapi/linux/ipv6.h ++++ b/include/uapi/linux/ipv6.h +@@ -131,7 +131,7 @@ struct ipv6hdr { + + struct in6_addr saddr; + struct in6_addr daddr; +-}; ++} __attribute__((packed, aligned(2))); + + + /* index values for the variables in ipv6_devconf */ +--- a/include/uapi/linux/tcp.h ++++ b/include/uapi/linux/tcp.h +@@ -55,7 +55,7 @@ struct tcphdr { + __be16 window; + __sum16 check; + __be16 urg_ptr; +-}; ++} __attribute__((packed, aligned(2))); + + /* + * The union cast uses a gcc extension to avoid aliasing problems +@@ -65,7 +65,7 @@ struct tcphdr { + union tcp_word_hdr { + struct tcphdr hdr; + __be32 words[5]; +-}; ++} __attribute__((packed, aligned(2))); + + #define tcp_flag_word(tp) ( ((union tcp_word_hdr *)(tp))->words [3]) + +--- a/include/uapi/linux/udp.h ++++ b/include/uapi/linux/udp.h +@@ -25,7 +25,7 @@ struct udphdr { + __be16 dest; + __be16 len; + __sum16 check; +-}; ++} __attribute__((packed, aligned(2))); + + /* UDP socket options */ + #define UDP_CORK 1 /* Never send partially complete segments */ +--- a/net/netfilter/nf_conntrack_core.c ++++ b/net/netfilter/nf_conntrack_core.c +@@ -271,8 +271,8 @@ nf_ct_get_tuple(const struct sk_buff *sk + + switch (l3num) { + case NFPROTO_IPV4: +- tuple->src.u3.ip = ap[0]; +- tuple->dst.u3.ip = ap[1]; ++ tuple->src.u3.ip = net_hdr_word(ap++); ++ tuple->dst.u3.ip = net_hdr_word(ap); + break; + case NFPROTO_IPV6: + memcpy(tuple->src.u3.ip6, ap, sizeof(tuple->src.u3.ip6)); +--- a/include/uapi/linux/icmp.h ++++ b/include/uapi/linux/icmp.h +@@ -82,7 +82,7 @@ struct icmphdr { + } frag; + __u8 reserved[4]; + } un; +-}; ++} __attribute__((packed, aligned(2))); + + + /* +--- a/include/uapi/linux/in6.h ++++ b/include/uapi/linux/in6.h +@@ -43,7 +43,7 @@ struct in6_addr { + #define s6_addr16 in6_u.u6_addr16 + #define s6_addr32 in6_u.u6_addr32 + #endif +-}; ++} __attribute__((packed, aligned(2))); + #endif /* __UAPI_DEF_IN6_ADDR */ + + #if __UAPI_DEF_SOCKADDR_IN6 +--- a/net/ipv6/tcp_ipv6.c ++++ b/net/ipv6/tcp_ipv6.c +@@ -35,6 +35,7 @@ + #include <linux/ipsec.h> + #include <linux/times.h> + #include <linux/slab.h> ++#include <asm/unaligned.h> + #include <linux/uaccess.h> + #include <linux/ipv6.h> + #include <linux/icmpv6.h> +@@ -849,10 +850,10 @@ static void tcp_v6_send_response(const s + topt = (__be32 *)(t1 + 1); + + if (tsecr) { +- *topt++ = htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) | +- (TCPOPT_TIMESTAMP << 8) | TCPOLEN_TIMESTAMP); +- *topt++ = htonl(tsval); +- *topt++ = htonl(tsecr); ++ put_unaligned_be32((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) | ++ (TCPOPT_TIMESTAMP << 8) | TCPOLEN_TIMESTAMP, topt++); ++ put_unaligned_be32(tsval, topt++); ++ put_unaligned_be32(tsecr, topt++); + } + + #ifdef CONFIG_TCP_MD5SIG +--- a/include/linux/ipv6.h ++++ b/include/linux/ipv6.h +@@ -6,6 +6,7 @@ + + #define ipv6_optlen(p) (((p)->hdrlen+1) << 3) + #define ipv6_authlen(p) (((p)->hdrlen+2) << 2) ++ + /* + * This structure contains configuration options per IPv6 link. + */ +--- a/net/ipv6/datagram.c ++++ b/net/ipv6/datagram.c +@@ -476,7 +476,7 @@ int ipv6_recv_error(struct sock *sk, str + ipv6_iface_scope_id(&sin->sin6_addr, + IP6CB(skb)->iif); + } else { +- ipv6_addr_set_v4mapped(*(__be32 *)(nh + serr->addr_offset), ++ ipv6_addr_set_v4mapped(net_hdr_word(nh + serr->addr_offset), + &sin->sin6_addr); + sin->sin6_scope_id = 0; + } +@@ -830,12 +830,12 @@ int ip6_datagram_send_ctl(struct net *ne + } + + if (fl6->flowlabel&IPV6_FLOWINFO_MASK) { +- if ((fl6->flowlabel^*(__be32 *)CMSG_DATA(cmsg))&~IPV6_FLOWINFO_MASK) { ++ if ((fl6->flowlabel^net_hdr_word(CMSG_DATA(cmsg)))&~IPV6_FLOWINFO_MASK) { + err = -EINVAL; + goto exit_f; + } + } +- fl6->flowlabel = IPV6_FLOWINFO_MASK & *(__be32 *)CMSG_DATA(cmsg); ++ fl6->flowlabel = IPV6_FLOWINFO_MASK & net_hdr_word(CMSG_DATA(cmsg)); + break; + + case IPV6_2292HOPOPTS: +--- a/net/ipv6/exthdrs.c ++++ b/net/ipv6/exthdrs.c +@@ -752,7 +752,7 @@ static bool ipv6_hop_jumbo(struct sk_buf + goto drop; + } + +- pkt_len = ntohl(*(__be32 *)(nh + optoff + 2)); ++ pkt_len = ntohl(net_hdr_word(nh + optoff + 2)); + if (pkt_len <= IPV6_MAXPLEN) { + __IP6_INC_STATS(net, idev, IPSTATS_MIB_INHDRERRORS); + icmpv6_param_prob(skb, ICMPV6_HDR_FIELD, optoff+2); +--- a/include/linux/types.h ++++ b/include/linux/types.h +@@ -225,5 +225,11 @@ struct callback_head { + typedef void (*rcu_callback_t)(struct rcu_head *head); + typedef void (*call_rcu_func_t)(struct rcu_head *head, rcu_callback_t func); + ++struct net_hdr_word { ++ u32 words[1]; ++} __attribute__((packed, aligned(2))); ++ ++#define net_hdr_word(_p) (((struct net_hdr_word *) (_p))->words[0]) ++ + #endif /* __ASSEMBLY__ */ + #endif /* _LINUX_TYPES_H */ +--- a/net/ipv4/af_inet.c ++++ b/net/ipv4/af_inet.c +@@ -1441,8 +1441,8 @@ struct sk_buff *inet_gro_receive(struct + if (unlikely(ip_fast_csum((u8 *)iph, 5))) + goto out_unlock; + +- id = ntohl(*(__be32 *)&iph->id); +- flush = (u16)((ntohl(*(__be32 *)iph) ^ skb_gro_len(skb)) | (id & ~IP_DF)); ++ id = ntohl(net_hdr_word(&iph->id)); ++ flush = (u16)((ntohl(net_hdr_word(iph)) ^ skb_gro_len(skb)) | (id & ~IP_DF)); + id >>= 16; + + list_for_each_entry(p, head, list) { +--- a/net/ipv4/tcp_output.c ++++ b/net/ipv4/tcp_output.c +@@ -460,48 +460,53 @@ static void tcp_options_write(__be32 *pt + u16 options = opts->options; /* mungable copy */ + + if (unlikely(OPTION_MD5 & options)) { +- *ptr++ = htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) | +- (TCPOPT_MD5SIG << 8) | TCPOLEN_MD5SIG); ++ net_hdr_word(ptr++) = ++ htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) | ++ (TCPOPT_MD5SIG << 8) | TCPOLEN_MD5SIG); + /* overload cookie hash location */ + opts->hash_location = (__u8 *)ptr; + ptr += 4; + } + + if (unlikely(opts->mss)) { +- *ptr++ = htonl((TCPOPT_MSS << 24) | +- (TCPOLEN_MSS << 16) | +- opts->mss); ++ net_hdr_word(ptr++) = ++ htonl((TCPOPT_MSS << 24) | (TCPOLEN_MSS << 16) | ++ opts->mss); + } + + if (likely(OPTION_TS & options)) { + if (unlikely(OPTION_SACK_ADVERTISE & options)) { +- *ptr++ = htonl((TCPOPT_SACK_PERM << 24) | +- (TCPOLEN_SACK_PERM << 16) | +- (TCPOPT_TIMESTAMP << 8) | +- TCPOLEN_TIMESTAMP); ++ net_hdr_word(ptr++) = ++ htonl((TCPOPT_SACK_PERM << 24) | ++ (TCPOLEN_SACK_PERM << 16) | ++ (TCPOPT_TIMESTAMP << 8) | ++ TCPOLEN_TIMESTAMP); + options &= ~OPTION_SACK_ADVERTISE; + } else { +- *ptr++ = htonl((TCPOPT_NOP << 24) | +- (TCPOPT_NOP << 16) | +- (TCPOPT_TIMESTAMP << 8) | +- TCPOLEN_TIMESTAMP); ++ net_hdr_word(ptr++) = ++ htonl((TCPOPT_NOP << 24) | ++ (TCPOPT_NOP << 16) | ++ (TCPOPT_TIMESTAMP << 8) | ++ TCPOLEN_TIMESTAMP); + } +- *ptr++ = htonl(opts->tsval); +- *ptr++ = htonl(opts->tsecr); ++ net_hdr_word(ptr++) = htonl(opts->tsval); ++ net_hdr_word(ptr++) = htonl(opts->tsecr); + } + + if (unlikely(OPTION_SACK_ADVERTISE & options)) { +- *ptr++ = htonl((TCPOPT_NOP << 24) | +- (TCPOPT_NOP << 16) | +- (TCPOPT_SACK_PERM << 8) | +- TCPOLEN_SACK_PERM); ++ net_hdr_word(ptr++) = ++ htonl((TCPOPT_NOP << 24) | ++ (TCPOPT_NOP << 16) | ++ (TCPOPT_SACK_PERM << 8) | ++ TCPOLEN_SACK_PERM); + } + + if (unlikely(OPTION_WSCALE & options)) { +- *ptr++ = htonl((TCPOPT_NOP << 24) | +- (TCPOPT_WINDOW << 16) | +- (TCPOLEN_WINDOW << 8) | +- opts->ws); ++ net_hdr_word(ptr++) = ++ htonl((TCPOPT_NOP << 24) | ++ (TCPOPT_WINDOW << 16) | ++ (TCPOLEN_WINDOW << 8) | ++ opts->ws); + } + + if (unlikely(opts->num_sack_blocks)) { +@@ -509,16 +514,17 @@ static void tcp_options_write(__be32 *pt + tp->duplicate_sack : tp->selective_acks; + int this_sack; + +- *ptr++ = htonl((TCPOPT_NOP << 24) | +- (TCPOPT_NOP << 16) | +- (TCPOPT_SACK << 8) | +- (TCPOLEN_SACK_BASE + (opts->num_sack_blocks * ++ net_hdr_word(ptr++) = ++ htonl((TCPOPT_NOP << 24) | ++ (TCPOPT_NOP << 16) | ++ (TCPOPT_SACK << 8) | ++ (TCPOLEN_SACK_BASE + (opts->num_sack_blocks * + TCPOLEN_SACK_PERBLOCK))); + + for (this_sack = 0; this_sack < opts->num_sack_blocks; + ++this_sack) { +- *ptr++ = htonl(sp[this_sack].start_seq); +- *ptr++ = htonl(sp[this_sack].end_seq); ++ net_hdr_word(ptr++) = htonl(sp[this_sack].start_seq); ++ net_hdr_word(ptr++) = htonl(sp[this_sack].end_seq); + } + + tp->rx_opt.dsack = 0; +@@ -531,13 +537,14 @@ static void tcp_options_write(__be32 *pt + + if (foc->exp) { + len = TCPOLEN_EXP_FASTOPEN_BASE + foc->len; +- *ptr = htonl((TCPOPT_EXP << 24) | (len << 16) | ++ net_hdr_word(ptr) = ++ htonl((TCPOPT_EXP << 24) | (len << 16) | + TCPOPT_FASTOPEN_MAGIC); + p += TCPOLEN_EXP_FASTOPEN_BASE; + } else { + len = TCPOLEN_FASTOPEN_BASE + foc->len; +- *p++ = TCPOPT_FASTOPEN; +- *p++ = len; ++ net_hdr_word(p++) = TCPOPT_FASTOPEN; ++ net_hdr_word(p++) = len; + } + + memcpy(p, foc->val, foc->len); +--- a/include/uapi/linux/igmp.h ++++ b/include/uapi/linux/igmp.h +@@ -33,7 +33,7 @@ struct igmphdr { + __u8 code; /* For newer IGMP */ + __sum16 csum; + __be32 group; +-}; ++} __attribute__((packed, aligned(2))); + + /* V3 group record types [grec_type] */ + #define IGMPV3_MODE_IS_INCLUDE 1 +@@ -49,7 +49,7 @@ struct igmpv3_grec { + __be16 grec_nsrcs; + __be32 grec_mca; + __be32 grec_src[0]; +-}; ++} __attribute__((packed, aligned(2))); + + struct igmpv3_report { + __u8 type; +@@ -58,7 +58,7 @@ struct igmpv3_report { + __be16 resv2; + __be16 ngrec; + struct igmpv3_grec grec[0]; +-}; ++} __attribute__((packed, aligned(2))); + + struct igmpv3_query { + __u8 type; +@@ -79,7 +79,7 @@ struct igmpv3_query { + __u8 qqic; + __be16 nsrcs; + __be32 srcs[0]; +-}; ++} __attribute__((packed, aligned(2))); + + #define IGMP_HOST_MEMBERSHIP_QUERY 0x11 /* From RFC1112 */ + #define IGMP_HOST_MEMBERSHIP_REPORT 0x12 /* Ditto */ +--- a/net/core/flow_dissector.c ++++ b/net/core/flow_dissector.c +@@ -212,7 +212,7 @@ __be32 __skb_flow_get_ports(const struct + ports = __skb_header_pointer(skb, thoff + poff, + sizeof(_ports), data, hlen, &_ports); + if (ports) +- return *ports; ++ return (__be32)net_hdr_word(ports); + } + + return 0; +--- a/include/uapi/linux/icmpv6.h ++++ b/include/uapi/linux/icmpv6.h +@@ -77,7 +77,7 @@ struct icmp6hdr { + #define icmp6_addrconf_other icmp6_dataun.u_nd_ra.other + #define icmp6_rt_lifetime icmp6_dataun.u_nd_ra.rt_lifetime + #define icmp6_router_pref icmp6_dataun.u_nd_ra.router_pref +-}; ++} __attribute__((packed, aligned(2))); + + + #define ICMPV6_ROUTER_PREF_LOW 0x3 +--- a/include/net/ndisc.h ++++ b/include/net/ndisc.h +@@ -92,7 +92,7 @@ struct ra_msg { + struct icmp6hdr icmph; + __be32 reachable_time; + __be32 retrans_timer; +-}; ++} __attribute__((packed, aligned(2))); + + struct rd_msg { + struct icmp6hdr icmph; +@@ -371,10 +371,10 @@ static inline u32 ndisc_hashfn(const voi + { + const u32 *p32 = pkey; + +- return (((p32[0] ^ hash32_ptr(dev)) * hash_rnd[0]) + +- (p32[1] * hash_rnd[1]) + +- (p32[2] * hash_rnd[2]) + +- (p32[3] * hash_rnd[3])); ++ return (((net_hdr_word(&p32[0]) ^ hash32_ptr(dev)) * hash_rnd[0]) + ++ (net_hdr_word(&p32[1]) * hash_rnd[1]) + ++ (net_hdr_word(&p32[2]) * hash_rnd[2]) + ++ (net_hdr_word(&p32[3]) * hash_rnd[3])); + } + + static inline struct neighbour *__ipv6_neigh_lookup_noref(struct net_device *dev, const void *pkey) +--- a/net/sched/cls_u32.c ++++ b/net/sched/cls_u32.c +@@ -155,7 +155,7 @@ next_knode: + data = skb_header_pointer(skb, toff, 4, &hdata); + if (!data) + goto out; +- if ((*data ^ key->val) & key->mask) { ++ if ((net_hdr_word(data) ^ key->val) & key->mask) { + n = rcu_dereference_bh(n->next); + goto next_knode; + } +@@ -206,8 +206,8 @@ check_terminal: + &hdata); + if (!data) + goto out; +- sel = ht->divisor & u32_hash_fold(*data, &n->sel, +- n->fshift); ++ sel = ht->divisor & u32_hash_fold(net_hdr_word(data), ++ &n->sel, n->fshift); + } + if (!(n->sel.flags & (TC_U32_VAROFFSET | TC_U32_OFFSET | TC_U32_EAT))) + goto next_ht; +--- a/net/ipv6/ip6_offload.c ++++ b/net/ipv6/ip6_offload.c +@@ -240,7 +240,7 @@ INDIRECT_CALLABLE_SCOPE struct sk_buff * + continue; + + iph2 = (struct ipv6hdr *)(p->data + off); +- first_word = *(__be32 *)iph ^ *(__be32 *)iph2; ++ first_word = net_hdr_word(iph) ^ net_hdr_word(iph2); + + /* All fields must match except length and Traffic Class. + * XXX skbs on the gro_list have all been parsed and pulled +--- a/include/net/addrconf.h ++++ b/include/net/addrconf.h +@@ -47,7 +47,7 @@ struct prefix_info { + __be32 reserved2; + + struct in6_addr prefix; +-}; ++} __attribute__((packed, aligned(2))); + + #include <linux/ipv6.h> + #include <linux/netdevice.h> +--- a/include/net/inet_ecn.h ++++ b/include/net/inet_ecn.h +@@ -140,9 +140,9 @@ static inline int IP6_ECN_set_ce(struct + if (INET_ECN_is_not_ect(ipv6_get_dsfield(iph))) + return 0; + +- from = *(__be32 *)iph; ++ from = net_hdr_word(iph); + to = from | htonl(INET_ECN_CE << 20); +- *(__be32 *)iph = to; ++ net_hdr_word(iph) = to; + if (skb->ip_summed == CHECKSUM_COMPLETE) + skb->csum = csum_add(csum_sub(skb->csum, (__force __wsum)from), + (__force __wsum)to); +--- a/include/net/ipv6.h ++++ b/include/net/ipv6.h +@@ -146,7 +146,7 @@ struct frag_hdr { + __u8 reserved; + __be16 frag_off; + __be32 identification; +-}; ++} __attribute__((packed, aligned(2))); + + #define IP6_MF 0x0001 + #define IP6_OFFSET 0xFFF8 +@@ -557,8 +557,8 @@ static inline void __ipv6_addr_set_half( + } + #endif + #endif +- addr[0] = wh; +- addr[1] = wl; ++ net_hdr_word(&addr[0]) = wh; ++ net_hdr_word(&addr[1]) = wl; + } + + static inline void ipv6_addr_set(struct in6_addr *addr, +@@ -617,6 +617,8 @@ static inline bool ipv6_prefix_equal(con + const __be32 *a1 = addr1->s6_addr32; + const __be32 *a2 = addr2->s6_addr32; + unsigned int pdw, pbi; ++ /* Used for last <32-bit fraction of prefix */ ++ u32 pbia1, pbia2; + + /* check complete u32 in prefix */ + pdw = prefixlen >> 5; +@@ -625,7 +627,9 @@ static inline bool ipv6_prefix_equal(con + + /* check incomplete u32 in prefix */ + pbi = prefixlen & 0x1f; +- if (pbi && ((a1[pdw] ^ a2[pdw]) & htonl((0xffffffff) << (32 - pbi)))) ++ pbia1 = net_hdr_word(&a1[pdw]); ++ pbia2 = net_hdr_word(&a2[pdw]); ++ if (pbi && ((pbia1 ^ pbia2) & htonl((0xffffffff) << (32 - pbi)))) + return false; + + return true; +@@ -741,13 +745,13 @@ static inline void ipv6_addr_set_v4mappe + */ + static inline int __ipv6_addr_diff32(const void *token1, const void *token2, int addrlen) + { +- const __be32 *a1 = token1, *a2 = token2; ++ const struct in6_addr *a1 = token1, *a2 = token2; + int i; + + addrlen >>= 2; + + for (i = 0; i < addrlen; i++) { +- __be32 xb = a1[i] ^ a2[i]; ++ __be32 xb = a1->s6_addr32[i] ^ a2->s6_addr32[i]; + if (xb) + return i * 32 + 31 - __fls(ntohl(xb)); + } +@@ -934,17 +938,18 @@ static inline int ip6_multipath_hash_pol + static inline void ip6_flow_hdr(struct ipv6hdr *hdr, unsigned int tclass, + __be32 flowlabel) + { +- *(__be32 *)hdr = htonl(0x60000000 | (tclass << 20)) | flowlabel; ++ net_hdr_word((__be32 *)hdr) = ++ htonl(0x60000000 | (tclass << 20)) | flowlabel; + } + + static inline __be32 ip6_flowinfo(const struct ipv6hdr *hdr) + { +- return *(__be32 *)hdr & IPV6_FLOWINFO_MASK; ++ return net_hdr_word((__be32 *)hdr) & IPV6_FLOWINFO_MASK; + } + + static inline __be32 ip6_flowlabel(const struct ipv6hdr *hdr) + { +- return *(__be32 *)hdr & IPV6_FLOWLABEL_MASK; ++ return net_hdr_word((__be32 *)hdr) & IPV6_FLOWLABEL_MASK; + } + + static inline u8 ip6_tclass(__be32 flowinfo) +--- a/include/net/secure_seq.h ++++ b/include/net/secure_seq.h +@@ -3,6 +3,7 @@ + #define _NET_SECURE_SEQ + + #include <linux/types.h> ++#include <linux/in6.h> + + u32 secure_ipv4_port_ephemeral(__be32 saddr, __be32 daddr, __be16 dport); + u32 secure_ipv6_port_ephemeral(const __be32 *saddr, const __be32 *daddr, +--- a/include/uapi/linux/in.h ++++ b/include/uapi/linux/in.h +@@ -84,7 +84,7 @@ enum { + /* Internet address. */ + struct in_addr { + __be32 s_addr; +-}; ++} __attribute__((packed, aligned(2))); + #endif + + #define IP_TOS 1 +--- a/net/ipv6/ip6_fib.c ++++ b/net/ipv6/ip6_fib.c +@@ -140,7 +140,7 @@ static __be32 addr_bit_set(const void *t + * See include/asm-generic/bitops/le.h. + */ + return (__force __be32)(1 << ((~fn_bit ^ BITOP_BE32_SWIZZLE) & 0x1f)) & +- addr[fn_bit >> 5]; ++ net_hdr_word(&addr[fn_bit >> 5]); + } + + struct fib6_info *fib6_info_alloc(gfp_t gfp_flags, bool with_fib6_nh) +--- a/net/netfilter/nf_conntrack_proto_tcp.c ++++ b/net/netfilter/nf_conntrack_proto_tcp.c +@@ -415,7 +415,7 @@ static void tcp_sack(const struct sk_buf + + /* Fast path for timestamp-only option */ + if (length == TCPOLEN_TSTAMP_ALIGNED +- && *(__be32 *)ptr == htonl((TCPOPT_NOP << 24) ++ && net_hdr_word(ptr) == htonl((TCPOPT_NOP << 24) + | (TCPOPT_NOP << 16) + | (TCPOPT_TIMESTAMP << 8) + | TCPOLEN_TIMESTAMP)) +--- a/net/xfrm/xfrm_input.c ++++ b/net/xfrm/xfrm_input.c +@@ -162,8 +162,8 @@ int xfrm_parse_spi(struct sk_buff *skb, + if (!pskb_may_pull(skb, hlen)) + return -EINVAL; + +- *spi = *(__be32 *)(skb_transport_header(skb) + offset); +- *seq = *(__be32 *)(skb_transport_header(skb) + offset_seq); ++ *spi = net_hdr_word(skb_transport_header(skb) + offset); ++ *seq = net_hdr_word(skb_transport_header(skb) + offset_seq); + return 0; + } + EXPORT_SYMBOL(xfrm_parse_spi); +--- a/net/ipv4/tcp_input.c ++++ b/net/ipv4/tcp_input.c +@@ -3976,14 +3976,16 @@ static bool tcp_parse_aligned_timestamp( + { + const __be32 *ptr = (const __be32 *)(th + 1); + +- if (*ptr == htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) +- | (TCPOPT_TIMESTAMP << 8) | TCPOLEN_TIMESTAMP)) { ++ if (net_hdr_word(ptr) == ++ htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) | ++ (TCPOPT_TIMESTAMP << 8) | TCPOLEN_TIMESTAMP)) { + tp->rx_opt.saw_tstamp = 1; + ++ptr; +- tp->rx_opt.rcv_tsval = ntohl(*ptr); ++ tp->rx_opt.rcv_tsval = get_unaligned_be32(ptr); + ++ptr; +- if (*ptr) +- tp->rx_opt.rcv_tsecr = ntohl(*ptr) - tp->tsoffset; ++ if (net_hdr_word(ptr)) ++ tp->rx_opt.rcv_tsecr = get_unaligned_be32(ptr) - ++ tp->tsoffset; + else + tp->rx_opt.rcv_tsecr = 0; + return true; +--- a/include/uapi/linux/if_pppox.h ++++ b/include/uapi/linux/if_pppox.h +@@ -51,6 +51,7 @@ struct pppoe_addr { + */ + struct pptp_addr { + __u16 call_id; ++ __u16 pad; + struct in_addr sin_addr; + }; + +--- a/net/ipv6/netfilter/nf_log_ipv6.c ++++ b/net/ipv6/netfilter/nf_log_ipv6.c +@@ -63,9 +63,9 @@ static void dump_ipv6_packet(struct net + /* Max length: 44 "LEN=65535 TC=255 HOPLIMIT=255 FLOWLBL=FFFFF " */ + nf_log_buf_add(m, "LEN=%zu TC=%u HOPLIMIT=%u FLOWLBL=%u ", + ntohs(ih->payload_len) + sizeof(struct ipv6hdr), +- (ntohl(*(__be32 *)ih) & 0x0ff00000) >> 20, ++ (ntohl(net_hdr_word(ih)) & 0x0ff00000) >> 20, + ih->hop_limit, +- (ntohl(*(__be32 *)ih) & 0x000fffff)); ++ (ntohl(net_hdr_word(ih)) & 0x000fffff)); + + fragment = 0; + ptr = ip6hoff + sizeof(struct ipv6hdr); +--- a/include/net/neighbour.h ++++ b/include/net/neighbour.h +@@ -274,8 +274,10 @@ static inline bool neigh_key_eq128(const + const u32 *n32 = (const u32 *)n->primary_key; + const u32 *p32 = pkey; + +- return ((n32[0] ^ p32[0]) | (n32[1] ^ p32[1]) | +- (n32[2] ^ p32[2]) | (n32[3] ^ p32[3])) == 0; ++ return ((n32[0] ^ net_hdr_word(&p32[0])) | ++ (n32[1] ^ net_hdr_word(&p32[1])) | ++ (n32[2] ^ net_hdr_word(&p32[2])) | ++ (n32[3] ^ net_hdr_word(&p32[3]))) == 0; + } + + static inline struct neighbour *___neigh_lookup_noref( +--- a/include/uapi/linux/netfilter_arp/arp_tables.h ++++ b/include/uapi/linux/netfilter_arp/arp_tables.h +@@ -70,7 +70,7 @@ struct arpt_arp { + __u8 flags; + /* Inverse flags */ + __u16 invflags; +-}; ++} __attribute__((aligned(4))); + + /* Values for "flag" field in struct arpt_ip (general arp structure). + * No flags defined yet. +--- a/net/core/utils.c ++++ b/net/core/utils.c +@@ -460,8 +460,14 @@ void inet_proto_csum_replace16(__sum16 * + bool pseudohdr) + { + __be32 diff[] = { +- ~from[0], ~from[1], ~from[2], ~from[3], +- to[0], to[1], to[2], to[3], ++ ~net_hdr_word(&from[0]), ++ ~net_hdr_word(&from[1]), ++ ~net_hdr_word(&from[2]), ++ ~net_hdr_word(&from[3]), ++ net_hdr_word(&to[0]), ++ net_hdr_word(&to[1]), ++ net_hdr_word(&to[2]), ++ net_hdr_word(&to[3]), + }; + if (skb->ip_summed != CHECKSUM_PARTIAL) { + *sum = csum_fold(csum_partial(diff, sizeof(diff), +--- a/include/linux/etherdevice.h ++++ b/include/linux/etherdevice.h +@@ -489,7 +489,7 @@ static inline bool is_etherdev_addr(cons + * @b: Pointer to Ethernet header + * + * Compare two Ethernet headers, returns 0 if equal. +- * This assumes that the network header (i.e., IP header) is 4-byte ++ * This assumes that the network header (i.e., IP header) is 2-byte + * aligned OR the platform can handle unaligned access. This is the + * case for all packets coming into netif_receive_skb or similar + * entry points. +@@ -512,11 +512,12 @@ static inline unsigned long compare_ethe + fold |= *(unsigned long *)(a + 6) ^ *(unsigned long *)(b + 6); + return fold; + #else +- u32 *a32 = (u32 *)((u8 *)a + 2); +- u32 *b32 = (u32 *)((u8 *)b + 2); ++ const u16 *a16 = a; ++ const u16 *b16 = b; + +- return (*(u16 *)a ^ *(u16 *)b) | (a32[0] ^ b32[0]) | +- (a32[1] ^ b32[1]) | (a32[2] ^ b32[2]); ++ return (a16[0] ^ b16[0]) | (a16[1] ^ b16[1]) | (a16[2] ^ b16[2]) | ++ (a16[3] ^ b16[3]) | (a16[4] ^ b16[4]) | (a16[5] ^ b16[5]) | ++ (a16[6] ^ b16[6]); + #endif + } + +--- a/net/ipv4/tcp_offload.c ++++ b/net/ipv4/tcp_offload.c +@@ -223,7 +223,7 @@ struct sk_buff *tcp_gro_receive(struct l + + th2 = tcp_hdr(p); + +- if (*(u32 *)&th->source ^ *(u32 *)&th2->source) { ++ if (net_hdr_word(&th->source) ^ net_hdr_word(&th2->source)) { + NAPI_GRO_CB(p)->same_flow = 0; + continue; + } +@@ -241,8 +241,8 @@ found: + ~(TCP_FLAG_CWR | TCP_FLAG_FIN | TCP_FLAG_PSH)); + flush |= (__force int)(th->ack_seq ^ th2->ack_seq); + for (i = sizeof(*th); i < thlen; i += 4) +- flush |= *(u32 *)((u8 *)th + i) ^ +- *(u32 *)((u8 *)th2 + i); ++ flush |= net_hdr_word((u8 *)th + i) ^ ++ net_hdr_word((u8 *)th2 + i); + + /* When we receive our second frame we can made a decision on if we + * continue this flow as an atomic flow with a fixed ID or if we use +--- a/net/ipv6/netfilter/ip6table_mangle.c ++++ b/net/ipv6/netfilter/ip6table_mangle.c +@@ -47,7 +47,7 @@ ip6t_mangle_out(struct sk_buff *skb, con + hop_limit = ipv6_hdr(skb)->hop_limit; + + /* flowlabel and prio (includes version, which shouldn't change either */ +- flowlabel = *((u_int32_t *)ipv6_hdr(skb)); ++ flowlabel = net_hdr_word(ipv6_hdr(skb)); + + ret = ip6t_do_table(skb, state, state->net->ipv6.ip6table_mangle); + +@@ -56,7 +56,7 @@ ip6t_mangle_out(struct sk_buff *skb, con + !ipv6_addr_equal(&ipv6_hdr(skb)->daddr, &daddr) || + skb->mark != mark || + ipv6_hdr(skb)->hop_limit != hop_limit || +- flowlabel != *((u_int32_t *)ipv6_hdr(skb)))) { ++ flowlabel != net_hdr_word(ipv6_hdr(skb)))) { + err = ip6_route_me_harder(state->net, state->sk, skb); + if (err < 0) + ret = NF_DROP_ERR(err); diff --git a/target/linux/ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch b/target/linux/ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch new file mode 100644 index 0000000000..dac2064cbb --- /dev/null +++ b/target/linux/ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch @@ -0,0 +1,54 @@ +From 4d3c17975c7814884a721fe693b3adf5c426d759 Mon Sep 17 00:00:00 2001 +From: Hauke Mehrtens <hauke@hauke-m.de> +Date: Tue, 10 Nov 2015 22:18:39 +0100 +Subject: [RFC] serial: core: add support for boot console with arbitrary + baud rates + +The Arduino Yun uses a baud rate of 250000 by default. The serial is +going over the Atmel ATmega and is used to connect to this chip. +Without this patch Linux wants to switch the console to 9600 Baud. + +With this patch Linux will use the configured baud rate and not a +default one specified in uart_register_driver(). + +Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> +[rebased to 4.14, slightly reworded commit message] +Signed-off-by: Sungbo Eo <mans0n@gorani.run> +--- + drivers/tty/serial/serial_core.c | 6 +++++- + include/linux/console.h | 1 + + 2 files changed, 6 insertions(+), 1 deletions(-) + +--- a/drivers/tty/serial/serial_core.c ++++ b/drivers/tty/serial/serial_core.c +@@ -220,6 +220,8 @@ static int uart_port_startup(struct tty_ + if (retval == 0) { + if (uart_console(uport) && uport->cons->cflag) { + tty->termios.c_cflag = uport->cons->cflag; ++ tty->termios.c_ospeed = uport->cons->baud; ++ tty->termios.c_ispeed = uport->cons->baud; + uport->cons->cflag = 0; + } + /* +@@ -2108,8 +2110,10 @@ uart_set_options(struct uart_port *port, + * Allow the setting of the UART parameters with a NULL console + * too: + */ +- if (co) ++ if (co) { + co->cflag = termios.c_cflag; ++ co->baud = baud; ++ } + + return 0; + } +--- a/include/linux/console.h ++++ b/include/linux/console.h +@@ -153,6 +153,7 @@ struct console { + short flags; + short index; + int cflag; ++ int baud; + void *data; + struct console *next; + }; diff --git a/target/linux/ath79/patches-5.10/930-ar8216-make-reg-access-atomic.patch b/target/linux/ath79/patches-5.10/930-ar8216-make-reg-access-atomic.patch new file mode 100644 index 0000000000..02f763534e --- /dev/null +++ b/target/linux/ath79/patches-5.10/930-ar8216-make-reg-access-atomic.patch @@ -0,0 +1,59 @@ +From b3797d1a92afe97c173b00fdb7824cedba24eef0 Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo <gch981213@gmail.com> +Date: Sun, 20 Sep 2020 01:00:45 +0800 +Subject: [PATCH] ath79: ar8216: make switch register access atomic + +due to some unknown reason these register accesses sometimes fail +on the integrated switch without this patch. + +THIS ONLY WORKS ON ATH79 AND MAY BREAK THE DRIVER ON OTHER PLATFORMS! +The mdio bus on ath79 works in polling mode and doesn't rely on +any interrupt. This patch breaks the driver on any mdio master +with interrupts used. + +--- +--- a/drivers/net/phy/ar8216.c ++++ b/drivers/net/phy/ar8216.c +@@ -252,6 +252,7 @@ ar8xxx_mii_write32(struct ar8xxx_priv *p + u32 + ar8xxx_read(struct ar8xxx_priv *priv, int reg) + { ++ unsigned long flags; + struct mii_bus *bus = priv->mii_bus; + u16 r1, r2, page; + u32 val; +@@ -259,11 +260,13 @@ ar8xxx_read(struct ar8xxx_priv *priv, in + split_addr((u32) reg, &r1, &r2, &page); + + mutex_lock(&bus->mdio_lock); ++ local_irq_save(flags); + + bus->write(bus, 0x18, 0, page); + wait_for_page_switch(); + val = ar8xxx_mii_read32(priv, 0x10 | r2, r1); + ++ local_irq_restore(flags); + mutex_unlock(&bus->mdio_lock); + + return val; +@@ -272,17 +275,20 @@ ar8xxx_read(struct ar8xxx_priv *priv, in + void + ar8xxx_write(struct ar8xxx_priv *priv, int reg, u32 val) + { ++ unsigned long flags; + struct mii_bus *bus = priv->mii_bus; + u16 r1, r2, page; + + split_addr((u32) reg, &r1, &r2, &page); + + mutex_lock(&bus->mdio_lock); ++ local_irq_save(flags); + + bus->write(bus, 0x18, 0, page); + wait_for_page_switch(); + ar8xxx_mii_write32(priv, 0x10 | r2, r1, val); + ++ local_irq_restore(flags); + mutex_unlock(&bus->mdio_lock); + } + diff --git a/target/linux/ath79/tiny/target.mk b/target/linux/ath79/tiny/target.mk index 91f135b56e..74b3e966c4 100644 --- a/target/linux/ath79/tiny/target.mk +++ b/target/linux/ath79/tiny/target.mk @@ -3,6 +3,8 @@ FEATURES += small_flash DEFAULT_PACKAGES += wpad-basic-wolfssl +KERNEL_TESTING_PATCHVER:=5.10 + define Target/Description Build firmware images for Atheros AR71xx/AR913x/AR934x based boards with small flash endef |