183 files changed, 0 insertions, 111722 deletions

diff --git a/target/linux/mediatek/files-5.4/drivers/leds/leds-ubnt-ledbar.c b/target/linux/mediatek/files-5.4/drivers/leds/leds-ubnt-ledbar.c
deleted file mode 100644
index 1f50038b8c..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/leds/leds-ubnt-ledbar.c
+++ /dev/null
@@ -1,210 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-
-#include <linux/delay.h>
-#include <linux/i2c.h>
-#include <linux/init.h>
-#include <linux/leds.h>
-#include <linux/module.h>
-#include <linux/mutex.h>
-#include <linux/of.h>
-#include <linux/of_gpio.h>
-#include <linux/gpio/consumer.h>
-
-/**
- * Driver for the Ubiquiti RGB LED controller (LEDBAR).
- * This Controller is based on a Holtek HT32F52241 and connected
- * via I2C.
- *
- *  - The Controller needs an enable signal set to high when
- *    performing a transaction. On the U6-LR, this is located
- *    at Pin 18 (R6902)
- *
- *  - The Pin is also printed when calling the "usetled" function
- *    contained in the ubntapp bootloader application.
- */
-
-#define UBNT_LEDBAR_MAX_BRIGHTNESS		0xff
-
-#define UBNT_LEDBAR_TRANSACTION_LENGTH	8
-#define UBNT_LEDBAR_TRANSACTION_SUCCESS	0xaa
-
-#define UBNT_LEDBAR_TRANSACTION_BLUE_IDX	2
-#define UBNT_LEDBAR_TRANSACTION_GREEN_IDX	3
-#define UBNT_LEDBAR_TRANSACTION_RED_IDX		4
-
-struct ubnt_ledbar {
-	struct mutex lock;
-	struct i2c_client *client;
-	struct led_classdev led_red;
-	struct led_classdev led_green;
-	struct led_classdev led_blue;
-	struct gpio_desc *enable_gpio;
-};
-
-static int ubnt_ledbar_perform_transaction(struct ubnt_ledbar *ledbar,
-					   char *transaction)
-{
-	int ret;
-	int i;
-
-	for (i = 0; i < UBNT_LEDBAR_TRANSACTION_LENGTH; i++)
-		i2c_smbus_write_byte(ledbar->client, transaction[i]);
-
-	return i2c_smbus_read_byte(ledbar->client);
-}
-
-static int ubnt_ledbar_apply_state(struct ubnt_ledbar *ledbar)
-{
-	char setup_msg[UBNT_LEDBAR_TRANSACTION_LENGTH] = {0x40, 0x10, 0x00, 0x00,
-							  0x00, 0x00, 0x00, 0x11};
-	char led_msg[UBNT_LEDBAR_TRANSACTION_LENGTH] = {0x40, 0x00, 0x00, 0x00,
-							0x00, 0x00, 0x01, 0x00};
-	char i2c_response;
-	int ret = 0;
-
-	mutex_lock(&ledbar->lock);
-
-	led_msg[UBNT_LEDBAR_TRANSACTION_BLUE_IDX] = ledbar->led_blue.brightness;
-	led_msg[UBNT_LEDBAR_TRANSACTION_GREEN_IDX] = ledbar->led_green.brightness;
-	led_msg[UBNT_LEDBAR_TRANSACTION_RED_IDX] = ledbar->led_red.brightness;
-
-	gpiod_set_raw_value(ledbar->enable_gpio, 1);
-
-	msleep(10);
-
-	i2c_response = ubnt_ledbar_perform_transaction(ledbar, setup_msg);
-	if (i2c_response != UBNT_LEDBAR_TRANSACTION_SUCCESS) {
-		dev_err(&ledbar->client->dev, "Error initializing LED transaction: %02x\n", ret);
-		ret = -EINVAL;
-		goto out_gpio;
-	}
-
-	i2c_response = ubnt_ledbar_perform_transaction(ledbar, led_msg);
-	if (i2c_response != UBNT_LEDBAR_TRANSACTION_SUCCESS) {
-		dev_err(&ledbar->client->dev, "Failed LED transaction: %02x\n", ret);
-		ret = -EINVAL;
-		goto out_gpio;
-	}
-
-	msleep(10);
-out_gpio:
-	gpiod_set_raw_value(ledbar->enable_gpio, 0);
-
-	mutex_unlock(&ledbar->lock);
-
-	return ret;
-}
-
-#define UBNT_LEDBAR_CONTROL_RGBS(name)				\
-static int ubnt_ledbar_set_##name##_brightness(struct led_classdev *led_cdev,\
-					enum led_brightness value)	\
-{									\
-	struct ubnt_ledbar *ledbar = \
-			container_of(led_cdev, struct ubnt_ledbar, led_##name); \
-	int ret; \
-	led_cdev->brightness = value; \
-	ret = ubnt_ledbar_apply_state(ledbar); \
-	return ret; \
-}
-
-UBNT_LEDBAR_CONTROL_RGBS(red);
-UBNT_LEDBAR_CONTROL_RGBS(green);
-UBNT_LEDBAR_CONTROL_RGBS(blue);
-
-
-static int ubnt_ledbar_init_led(struct device_node *np, struct ubnt_ledbar *ledbar,
-				struct led_classdev *led_cdev)
-{
-	struct led_init_data init_data = {};
-	int ret;
-
-	if (!np)
-		return 0;
-
-	init_data.fwnode = of_fwnode_handle(np);
-
-	led_cdev->max_brightness = UBNT_LEDBAR_MAX_BRIGHTNESS;
-
-	ret = devm_led_classdev_register_ext(&ledbar->client->dev, led_cdev,
-					     &init_data);
-	if (ret)
-		dev_err(&ledbar->client->dev, "led register err: %d\n", ret);
-
-	return ret;
-}
-
-
-static int ubnt_ledbar_probe(struct i2c_client *client,
-			     const struct i2c_device_id *id)
-{
-	struct device_node *np = client->dev.of_node;
-	struct ubnt_ledbar *ledbar;
-	int ret;
-
-	ledbar = devm_kzalloc(&client->dev, sizeof(*ledbar), GFP_KERNEL);
-	if (!ledbar)
-		return -ENOMEM;
-
-	ledbar->enable_gpio = devm_gpiod_get(&client->dev, "enable", GPIOD_OUT_LOW);
-
-	if (IS_ERR(ledbar->enable_gpio)) {
-		ret = PTR_ERR(ledbar->enable_gpio);
-		dev_err(&client->dev, "Failed to get enable gpio: %d\n", ret);
-		return ret;
-	}
-
-	gpiod_direction_output(ledbar->enable_gpio, 0);
-
-	ledbar->client = client;
-
-	mutex_init(&ledbar->lock);
-
-	i2c_set_clientdata(client, ledbar);
-
-	ledbar->led_red.brightness_set_blocking = ubnt_ledbar_set_red_brightness;
-	ubnt_ledbar_init_led(of_get_child_by_name(np, "red"), ledbar, &ledbar->led_red);
-
-	ledbar->led_green.brightness_set_blocking = ubnt_ledbar_set_green_brightness;
-	ubnt_ledbar_init_led(of_get_child_by_name(np, "green"), ledbar, &ledbar->led_green);
-
-	ledbar->led_blue.brightness_set_blocking = ubnt_ledbar_set_blue_brightness;
-	ubnt_ledbar_init_led(of_get_child_by_name(np, "blue"), ledbar, &ledbar->led_blue);
-
-	return ubnt_ledbar_apply_state(ledbar);
-}
-
-static int ubnt_ledbar_remove(struct i2c_client *client)
-{
-	struct ubnt_ledbar *ledbar = i2c_get_clientdata(client);
-
-	mutex_destroy(&ledbar->lock);
-
-	return 0;
-}
-
-static const struct i2c_device_id ubnt_ledbar_id[] = {
-	{ "ubnt-ledbar", 0 },
-	{ }
-};
-MODULE_DEVICE_TABLE(i2c, ubnt_ledbar_id);
-
-static const struct of_device_id of_ubnt_ledbar_match[] = {
-	{ .compatible = "ubnt,ledbar", },
-	{},
-};
-MODULE_DEVICE_TABLE(of, of_ubnt_ledbar_match);
-
-static struct i2c_driver ubnt_ledbar_driver = {
-	.driver = {
-		.name	= "ubnt-ledbar",
-		.of_match_table = of_ubnt_ledbar_match,
-	},
-	.probe		= ubnt_ledbar_probe,
-	.remove		= ubnt_ledbar_remove,
-	.id_table	= ubnt_ledbar_id,
-};
-module_i2c_driver(ubnt_ledbar_driver);
-
-MODULE_DESCRIPTION("Ubiquiti LEDBAR driver");
-MODULE_AUTHOR("David Bauer <mail@david-bauer.net>");
-MODULE_LICENSE("GPL v2");
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/Kconfig b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/Kconfig
deleted file mode 100644
index d9e0230cf0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/Kconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-
-config MT753X_GSW
-	tristate "Driver for the MediaTek MT753x switch"
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/Makefile b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/Makefile
deleted file mode 100644
index 7aae451cd1..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-#
-# Makefile for MediaTek MT753x gigabit switch
-#
-
-obj-$(CONFIG_MT753X_GSW)	+= mt753x.o
-
-mt753x-$(CONFIG_SWCONFIG)	+= mt753x_swconfig.o
-
-mt753x-y			+= mt753x_mdio.o mt7530.o mt7531.o \
-					mt753x_common.o mt753x_vlan.o \
-					mt753x_nl.o
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7530.c b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7530.c
deleted file mode 100644
index 6a94d0d2f4..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7530.c
+++ /dev/null
@@ -1,631 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-#include <linux/kernel.h>
-#include <linux/delay.h>
-
-#include "mt753x.h"
-#include "mt753x_regs.h"
-
-/* MT7530 registers */
-
-/* Unique fields of PMCR for MT7530 */
-#define FORCE_MODE			BIT(15)
-
-/* Unique fields of GMACCR for MT7530 */
-#define VLAN_SUPT_NO_S			14
-#define VLAN_SUPT_NO_M			0x1c000
-#define LATE_COL_DROP			BIT(13)
-
-/* Unique fields of (M)HWSTRAP for MT7530 */
-#define BOND_OPTION			BIT(24)
-#define P5_PHY0_SEL			BIT(20)
-#define CHG_TRAP			BIT(16)
-#define LOOPDET_DIS			BIT(14)
-#define P5_INTF_SEL_GMAC5		BIT(13)
-#define SMI_ADDR_S			11
-#define SMI_ADDR_M			0x1800
-#define XTAL_FSEL_S			9
-#define XTAL_FSEL_M			0x600
-#define P6_INTF_DIS			BIT(8)
-#define P5_INTF_MODE_RGMII		BIT(7)
-#define P5_INTF_DIS_S			BIT(6)
-#define C_MDIO_BPS_S			BIT(5)
-#define EEPROM_EN_S			BIT(4)
-
-/* PHY EEE Register bitmap of define */
-#define PHY_DEV07			0x07
-#define PHY_DEV07_REG_03C		0x3c
-
-/* PHY Extend Register 0x14 bitmap of define */
-#define PHY_EXT_REG_14			0x14
-
-/* Fields of PHY_EXT_REG_14 */
-#define PHY_EN_DOWN_SHFIT		BIT(4)
-
-/* PHY Token Ring Register 0x10 bitmap of define */
-#define PHY_TR_REG_10			0x10
-
-/* PHY Token Ring Register 0x12 bitmap of define */
-#define PHY_TR_REG_12			0x12
-
-/* PHY LPI PCS/DSP Control Register bitmap of define */
-#define PHY_LPI_REG_11			0x11
-
-/* PHY DEV 0x1e Register bitmap of define */
-#define PHY_DEV1E			0x1e
-#define PHY_DEV1E_REG_123		0x123
-#define PHY_DEV1E_REG_A6		0xa6
-
-/* Values of XTAL_FSEL */
-#define XTAL_20MHZ			1
-#define XTAL_40MHZ			2
-#define XTAL_25MHZ			3
-
-#define P6ECR				0x7830
-#define P6_INTF_MODE_TRGMII		BIT(0)
-
-#define TRGMII_TXCTRL			0x7a40
-#define TRAIN_TXEN			BIT(31)
-#define TXC_INV				BIT(30)
-#define TX_DOEO				BIT(29)
-#define TX_RST				BIT(28)
-
-#define TRGMII_TD0_CTRL			0x7a50
-#define TRGMII_TD1_CTRL			0x7a58
-#define TRGMII_TD2_CTRL			0x7a60
-#define TRGMII_TD3_CTRL			0x7a68
-#define TRGMII_TXCTL_CTRL		0x7a70
-#define TRGMII_TCK_CTRL			0x7a78
-#define TRGMII_TD_CTRL(n)		(0x7a50 + (n) * 8)
-#define NUM_TRGMII_CTRL			6
-#define TX_DMPEDRV			BIT(31)
-#define TX_DM_SR			BIT(15)
-#define TX_DMERODT			BIT(14)
-#define TX_DMOECTL			BIT(13)
-#define TX_TAP_S			8
-#define TX_TAP_M			0xf00
-#define TX_TRAIN_WD_S			0
-#define TX_TRAIN_WD_M			0xff
-
-#define TRGMII_TD0_ODT			0x7a54
-#define TRGMII_TD1_ODT			0x7a5c
-#define TRGMII_TD2_ODT			0x7a64
-#define TRGMII_TD3_ODT			0x7a6c
-#define TRGMII_TXCTL_ODT		0x7574
-#define TRGMII_TCK_ODT			0x757c
-#define TRGMII_TD_ODT(n)		(0x7a54 + (n) * 8)
-#define NUM_TRGMII_ODT			6
-#define TX_DM_DRVN_PRE_S		30
-#define TX_DM_DRVN_PRE_M		0xc0000000
-#define TX_DM_DRVP_PRE_S		28
-#define TX_DM_DRVP_PRE_M		0x30000000
-#define TX_DM_TDSEL_S			24
-#define TX_DM_TDSEL_M			0xf000000
-#define TX_ODTEN			BIT(23)
-#define TX_DME_PRE			BIT(20)
-#define TX_DM_DRVNT0			BIT(19)
-#define TX_DM_DRVPT0			BIT(18)
-#define TX_DM_DRVNTE			BIT(17)
-#define TX_DM_DRVPTE			BIT(16)
-#define TX_DM_ODTN_S			12
-#define TX_DM_ODTN_M			0x7000
-#define TX_DM_ODTP_S			8
-#define TX_DM_ODTP_M			0x700
-#define TX_DM_DRVN_S			4
-#define TX_DM_DRVN_M			0xf0
-#define TX_DM_DRVP_S			0
-#define TX_DM_DRVP_M			0x0f
-
-#define P5RGMIIRXCR			0x7b00
-#define CSR_RGMII_RCTL_CFG_S		24
-#define CSR_RGMII_RCTL_CFG_M		0x7000000
-#define CSR_RGMII_RXD_CFG_S		16
-#define CSR_RGMII_RXD_CFG_M		0x70000
-#define CSR_RGMII_EDGE_ALIGN		BIT(8)
-#define CSR_RGMII_RXC_90DEG_CFG_S	4
-#define CSR_RGMII_RXC_90DEG_CFG_M	0xf0
-#define CSR_RGMII_RXC_0DEG_CFG_S	0
-#define CSR_RGMII_RXC_0DEG_CFG_M	0x0f
-
-#define P5RGMIITXCR			0x7b04
-#define CSR_RGMII_TXEN_CFG_S		16
-#define CSR_RGMII_TXEN_CFG_M		0x70000
-#define CSR_RGMII_TXD_CFG_S		8
-#define CSR_RGMII_TXD_CFG_M		0x700
-#define CSR_RGMII_TXC_CFG_S		0
-#define CSR_RGMII_TXC_CFG_M		0x1f
-
-#define CHIP_REV			0x7ffc
-#define CHIP_NAME_S			16
-#define CHIP_NAME_M			0xffff0000
-#define CHIP_REV_S			0
-#define CHIP_REV_M			0x0f
-
-/* MMD registers */
-#define CORE_PLL_GROUP2			0x401
-#define RG_SYSPLL_EN_NORMAL		BIT(15)
-#define RG_SYSPLL_VODEN			BIT(14)
-#define RG_SYSPLL_POSDIV_S		5
-#define RG_SYSPLL_POSDIV_M		0x60
-
-#define CORE_PLL_GROUP4			0x403
-#define RG_SYSPLL_DDSFBK_EN		BIT(12)
-#define RG_SYSPLL_BIAS_EN		BIT(11)
-#define RG_SYSPLL_BIAS_LPF_EN		BIT(10)
-
-#define CORE_PLL_GROUP5			0x404
-#define RG_LCDDS_PCW_NCPO1_S		0
-#define RG_LCDDS_PCW_NCPO1_M		0xffff
-
-#define CORE_PLL_GROUP6			0x405
-#define RG_LCDDS_PCW_NCPO0_S		0
-#define RG_LCDDS_PCW_NCPO0_M		0xffff
-
-#define CORE_PLL_GROUP7			0x406
-#define RG_LCDDS_PWDB			BIT(15)
-#define RG_LCDDS_ISO_EN			BIT(13)
-#define RG_LCCDS_C_S			4
-#define RG_LCCDS_C_M			0x70
-#define RG_LCDDS_PCW_NCPO_CHG		BIT(3)
-
-#define CORE_PLL_GROUP10		0x409
-#define RG_LCDDS_SSC_DELTA_S		0
-#define RG_LCDDS_SSC_DELTA_M		0xfff
-
-#define CORE_PLL_GROUP11		0x40a
-#define RG_LCDDS_SSC_DELTA1_S		0
-#define RG_LCDDS_SSC_DELTA1_M		0xfff
-
-#define CORE_GSWPLL_GCR_1		0x040d
-#define GSWPLL_PREDIV_S			14
-#define GSWPLL_PREDIV_M			0xc000
-#define GSWPLL_POSTDIV_200M_S		12
-#define GSWPLL_POSTDIV_200M_M		0x3000
-#define GSWPLL_EN_PRE			BIT(11)
-#define GSWPLL_FBKSEL			BIT(10)
-#define GSWPLL_BP			BIT(9)
-#define GSWPLL_BR			BIT(8)
-#define GSWPLL_FBKDIV_200M_S		0
-#define GSWPLL_FBKDIV_200M_M		0xff
-
-#define CORE_GSWPLL_GCR_2		0x040e
-#define GSWPLL_POSTDIV_500M_S		8
-#define GSWPLL_POSTDIV_500M_M		0x300
-#define GSWPLL_FBKDIV_500M_S		0
-#define GSWPLL_FBKDIV_500M_M		0xff
-
-#define TRGMII_GSW_CLK_CG		0x0410
-#define TRGMIICK_EN			BIT(1)
-#define GSWCK_EN			BIT(0)
-
-static int mt7530_mii_read(struct gsw_mt753x *gsw, int phy, int reg)
-{
-	if (phy < MT753X_NUM_PHYS)
-		phy = (gsw->phy_base + phy) & MT753X_SMI_ADDR_MASK;
-
-	return mdiobus_read(gsw->host_bus, phy, reg);
-}
-
-static void mt7530_mii_write(struct gsw_mt753x *gsw, int phy, int reg, u16 val)
-{
-	if (phy < MT753X_NUM_PHYS)
-		phy = (gsw->phy_base + phy) & MT753X_SMI_ADDR_MASK;
-
-	mdiobus_write(gsw->host_bus, phy, reg, val);
-}
-
-static int mt7530_mmd_read(struct gsw_mt753x *gsw, int addr, int devad, u16 reg)
-{
-	u16 val;
-
-	if (addr < MT753X_NUM_PHYS)
-		addr = (gsw->phy_base + addr) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->host_bus->mdio_lock);
-
-	gsw->host_bus->write(gsw->host_bus, addr, MII_MMD_ACC_CTL_REG,
-			     (MMD_ADDR << MMD_CMD_S) |
-			     ((devad << MMD_DEVAD_S) & MMD_DEVAD_M));
-
-	gsw->host_bus->write(gsw->host_bus, addr, MII_MMD_ADDR_DATA_REG, reg);
-
-	gsw->host_bus->write(gsw->host_bus, addr, MII_MMD_ACC_CTL_REG,
-			     (MMD_DATA << MMD_CMD_S) |
-			     ((devad << MMD_DEVAD_S) & MMD_DEVAD_M));
-
-	val = gsw->host_bus->read(gsw->host_bus, addr, MII_MMD_ADDR_DATA_REG);
-
-	mutex_unlock(&gsw->host_bus->mdio_lock);
-
-	return val;
-}
-
-static void mt7530_mmd_write(struct gsw_mt753x *gsw, int addr, int devad,
-			     u16 reg, u16 val)
-{
-	if (addr < MT753X_NUM_PHYS)
-		addr = (gsw->phy_base + addr) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->host_bus->mdio_lock);
-
-	gsw->host_bus->write(gsw->host_bus, addr, MII_MMD_ACC_CTL_REG,
-		      (MMD_ADDR << MMD_CMD_S) |
-		      ((devad << MMD_DEVAD_S) & MMD_DEVAD_M));
-
-	gsw->host_bus->write(gsw->host_bus, addr, MII_MMD_ADDR_DATA_REG, reg);
-
-	gsw->host_bus->write(gsw->host_bus, addr, MII_MMD_ACC_CTL_REG,
-		      (MMD_DATA << MMD_CMD_S) |
-		      ((devad << MMD_DEVAD_S) & MMD_DEVAD_M));
-
-	gsw->host_bus->write(gsw->host_bus, addr, MII_MMD_ADDR_DATA_REG, val);
-
-	mutex_unlock(&gsw->host_bus->mdio_lock);
-}
-
-static void mt7530_core_reg_write(struct gsw_mt753x *gsw, u32 reg, u32 val)
-{
-	gsw->mmd_write(gsw, 0, 0x1f, reg, val);
-}
-
-static void mt7530_trgmii_setting(struct gsw_mt753x *gsw)
-{
-	u16 i;
-
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP5, 0x0780);
-	mdelay(1);
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP6, 0);
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP10, 0x87);
-	mdelay(1);
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP11, 0x87);
-
-	/* PLL BIAS enable */
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP4,
-			      RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN);
-	mdelay(1);
-
-	/* PLL LPF enable */
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP4,
-			      RG_SYSPLL_DDSFBK_EN |
-			      RG_SYSPLL_BIAS_EN | RG_SYSPLL_BIAS_LPF_EN);
-
-	/* sys PLL enable */
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP2,
-			      RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
-			      (1 << RG_SYSPLL_POSDIV_S));
-
-	/* LCDDDS PWDS */
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP7,
-			      (3 << RG_LCCDS_C_S) |
-			      RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
-	mdelay(1);
-
-	/* Enable MT7530 TRGMII clock */
-	mt7530_core_reg_write(gsw, TRGMII_GSW_CLK_CG, GSWCK_EN | TRGMIICK_EN);
-
-	/* lower Tx Driving */
-	for (i = 0 ; i < NUM_TRGMII_ODT; i++)
-		mt753x_reg_write(gsw, TRGMII_TD_ODT(i),
-				 (4 << TX_DM_DRVP_S) | (4 << TX_DM_DRVN_S));
-}
-
-static void mt7530_rgmii_setting(struct gsw_mt753x *gsw)
-{
-	u32 val;
-
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP5, 0x0c80);
-	mdelay(1);
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP6, 0);
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP10, 0x87);
-	mdelay(1);
-	mt7530_core_reg_write(gsw, CORE_PLL_GROUP11, 0x87);
-
-	val = mt753x_reg_read(gsw, TRGMII_TXCTRL);
-	val &= ~TXC_INV;
-	mt753x_reg_write(gsw, TRGMII_TXCTRL, val);
-
-	mt753x_reg_write(gsw, TRGMII_TCK_CTRL,
-			 (8 << TX_TAP_S) | (0x55 << TX_TRAIN_WD_S));
-}
-
-static int mt7530_mac_port_setup(struct gsw_mt753x *gsw)
-{
-	u32 hwstrap, p6ecr = 0, p5mcr, p6mcr, phyad;
-
-	hwstrap = mt753x_reg_read(gsw, MHWSTRAP);
-	hwstrap &= ~(P6_INTF_DIS | P5_INTF_MODE_RGMII | P5_INTF_DIS_S);
-	hwstrap |= P5_INTF_SEL_GMAC5;
-	if (!gsw->port5_cfg.enabled) {
-		p5mcr = FORCE_MODE;
-		hwstrap |= P5_INTF_DIS_S;
-	} else {
-		p5mcr = (IPG_96BIT_WITH_SHORT_IPG << IPG_CFG_S) |
-			MAC_MODE | MAC_TX_EN | MAC_RX_EN |
-			BKOFF_EN | BACKPR_EN;
-
-		if (gsw->port5_cfg.force_link) {
-			p5mcr |= FORCE_MODE | FORCE_LINK | FORCE_RX_FC |
-				 FORCE_TX_FC;
-			p5mcr |= gsw->port5_cfg.speed << FORCE_SPD_S;
-
-			if (gsw->port5_cfg.duplex)
-				p5mcr |= FORCE_DPX;
-		}
-
-		switch (gsw->port5_cfg.phy_mode) {
-		case PHY_INTERFACE_MODE_MII:
-		case PHY_INTERFACE_MODE_GMII:
-			break;
-		case PHY_INTERFACE_MODE_RGMII:
-			hwstrap |= P5_INTF_MODE_RGMII;
-			break;
-		default:
-			dev_info(gsw->dev, "%s is not supported by port5\n",
-				 phy_modes(gsw->port5_cfg.phy_mode));
-			p5mcr = FORCE_MODE;
-			hwstrap |= P5_INTF_DIS_S;
-		}
-
-		/* Port5 to PHY direct mode */
-		if (of_property_read_u32(gsw->port5_cfg.np, "phy-address",
-					 &phyad))
-			goto parse_p6;
-
-		if (phyad != 0 && phyad != 4) {
-			dev_info(gsw->dev,
-				 "Only PHY 0/4 can be connected to Port 5\n");
-			goto parse_p6;
-		}
-
-		hwstrap &= ~P5_INTF_SEL_GMAC5;
-		if (phyad == 0)
-			hwstrap |= P5_PHY0_SEL;
-		else
-			hwstrap &= ~P5_PHY0_SEL;
-	}
-
-parse_p6:
-	if (!gsw->port6_cfg.enabled) {
-		p6mcr = FORCE_MODE;
-		hwstrap |= P6_INTF_DIS;
-	} else {
-		p6mcr = (IPG_96BIT_WITH_SHORT_IPG << IPG_CFG_S) |
-			MAC_MODE | MAC_TX_EN | MAC_RX_EN |
-			BKOFF_EN | BACKPR_EN;
-
-		if (gsw->port6_cfg.force_link) {
-			p6mcr |= FORCE_MODE | FORCE_LINK | FORCE_RX_FC |
-				 FORCE_TX_FC;
-			p6mcr |= gsw->port6_cfg.speed << FORCE_SPD_S;
-
-			if (gsw->port6_cfg.duplex)
-				p6mcr |= FORCE_DPX;
-		}
-
-		switch (gsw->port6_cfg.phy_mode) {
-		case PHY_INTERFACE_MODE_RGMII:
-			p6ecr = BIT(1);
-			break;
-		case PHY_INTERFACE_MODE_TRGMII:
-			/* set MT7530 central align */
-			p6ecr = BIT(0);
-			break;
-		default:
-			dev_info(gsw->dev, "%s is not supported by port6\n",
-				 phy_modes(gsw->port6_cfg.phy_mode));
-			p6mcr = FORCE_MODE;
-			hwstrap |= P6_INTF_DIS;
-		}
-	}
-
-	mt753x_reg_write(gsw, MHWSTRAP, hwstrap);
-	mt753x_reg_write(gsw, P6ECR, p6ecr);
-
-	mt753x_reg_write(gsw, PMCR(5), p5mcr);
-	mt753x_reg_write(gsw, PMCR(6), p6mcr);
-
-	return 0;
-}
-
-static void mt7530_core_pll_setup(struct gsw_mt753x *gsw)
-{
-	u32 hwstrap;
-
-	hwstrap = mt753x_reg_read(gsw, HWSTRAP);
-
-	switch ((hwstrap & XTAL_FSEL_M) >> XTAL_FSEL_S) {
-	case XTAL_40MHZ:
-		/* Disable MT7530 core clock */
-		mt7530_core_reg_write(gsw, TRGMII_GSW_CLK_CG, 0);
-
-		/* disable MT7530 PLL */
-		mt7530_core_reg_write(gsw, CORE_GSWPLL_GCR_1,
-				      (2 << GSWPLL_POSTDIV_200M_S) |
-				      (32 << GSWPLL_FBKDIV_200M_S));
-
-		/* For MT7530 core clock = 500Mhz */
-		mt7530_core_reg_write(gsw, CORE_GSWPLL_GCR_2,
-				      (1 << GSWPLL_POSTDIV_500M_S) |
-				      (25 << GSWPLL_FBKDIV_500M_S));
-
-		/* Enable MT7530 PLL */
-		mt7530_core_reg_write(gsw, CORE_GSWPLL_GCR_1,
-				      (2 << GSWPLL_POSTDIV_200M_S) |
-				      (32 << GSWPLL_FBKDIV_200M_S) |
-				      GSWPLL_EN_PRE);
-
-		usleep_range(20, 40);
-
-		/* Enable MT7530 core clock */
-		mt7530_core_reg_write(gsw, TRGMII_GSW_CLK_CG, GSWCK_EN);
-		break;
-	default:
-		/* TODO: PLL settings for 20/25MHz */
-		break;
-	}
-
-	hwstrap = mt753x_reg_read(gsw, HWSTRAP);
-	hwstrap |= CHG_TRAP;
-	if (gsw->direct_phy_access)
-		hwstrap &= ~C_MDIO_BPS_S;
-	else
-		hwstrap |= C_MDIO_BPS_S;
-
-	mt753x_reg_write(gsw, MHWSTRAP, hwstrap);
-
-	if (gsw->port6_cfg.enabled &&
-	    gsw->port6_cfg.phy_mode == PHY_INTERFACE_MODE_TRGMII) {
-		mt7530_trgmii_setting(gsw);
-	} else {
-		/* RGMII */
-		mt7530_rgmii_setting(gsw);
-	}
-
-	/* delay setting for 10/1000M */
-	mt753x_reg_write(gsw, P5RGMIIRXCR,
-			 CSR_RGMII_EDGE_ALIGN |
-			 (2 << CSR_RGMII_RXC_0DEG_CFG_S));
-	mt753x_reg_write(gsw, P5RGMIITXCR, 0x14 << CSR_RGMII_TXC_CFG_S);
-}
-
-static int mt7530_sw_detect(struct gsw_mt753x *gsw, struct chip_rev *crev)
-{
-	u32 rev;
-
-	rev = mt753x_reg_read(gsw, CHIP_REV);
-
-	if (((rev & CHIP_NAME_M) >> CHIP_NAME_S) == MT7530) {
-		if (crev) {
-			crev->rev = rev & CHIP_REV_M;
-			crev->name = "MT7530";
-		}
-
-		return 0;
-	}
-
-	return -ENODEV;
-}
-
-static void mt7530_phy_setting(struct gsw_mt753x *gsw)
-{
-	int i;
-	u32 val;
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		/* Disable EEE */
-		gsw->mmd_write(gsw, i, PHY_DEV07, PHY_DEV07_REG_03C, 0);
-
-		/* Enable HW auto downshift */
-		gsw->mii_write(gsw, i, 0x1f, 0x1);
-		val = gsw->mii_read(gsw, i, PHY_EXT_REG_14);
-		val |= PHY_EN_DOWN_SHFIT;
-		gsw->mii_write(gsw, i, PHY_EXT_REG_14, val);
-
-		/* Increase SlvDPSready time */
-		gsw->mii_write(gsw, i, 0x1f, 0x52b5);
-		gsw->mii_write(gsw, i, PHY_TR_REG_10, 0xafae);
-		gsw->mii_write(gsw, i, PHY_TR_REG_12, 0x2f);
-		gsw->mii_write(gsw, i, PHY_TR_REG_10, 0x8fae);
-
-		/* Increase post_update_timer */
-		gsw->mii_write(gsw, i, 0x1f, 0x3);
-		gsw->mii_write(gsw, i, PHY_LPI_REG_11, 0x4b);
-		gsw->mii_write(gsw, i, 0x1f, 0);
-
-		/* Adjust 100_mse_threshold */
-		gsw->mmd_write(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_123, 0xffff);
-
-		/* Disable mcc */
-		gsw->mmd_write(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_A6, 0x300);
-	}
-}
-
-static inline bool get_phy_access_mode(const struct device_node *np)
-{
-	return of_property_read_bool(np, "mt7530,direct-phy-access");
-}
-
-static int mt7530_sw_init(struct gsw_mt753x *gsw)
-{
-	int i;
-	u32 val;
-
-	gsw->direct_phy_access = get_phy_access_mode(gsw->dev->of_node);
-
-	/* Force MT7530 to use (in)direct PHY access */
-	val = mt753x_reg_read(gsw, HWSTRAP);
-	val |= CHG_TRAP;
-	if (gsw->direct_phy_access)
-		val &= ~C_MDIO_BPS_S;
-	else
-		val |= C_MDIO_BPS_S;
-	mt753x_reg_write(gsw, MHWSTRAP, val);
-
-	/* Read PHY address base from HWSTRAP */
-	gsw->phy_base  = (((val & SMI_ADDR_M) >> SMI_ADDR_S) << 3) + 8;
-	gsw->phy_base &= MT753X_SMI_ADDR_MASK;
-
-	if (gsw->direct_phy_access) {
-		gsw->mii_read = mt7530_mii_read;
-		gsw->mii_write = mt7530_mii_write;
-		gsw->mmd_read = mt7530_mmd_read;
-		gsw->mmd_write = mt7530_mmd_write;
-	} else {
-		gsw->mii_read = mt753x_mii_read;
-		gsw->mii_write = mt753x_mii_write;
-		gsw->mmd_read = mt753x_mmd_ind_read;
-		gsw->mmd_write = mt753x_mmd_ind_write;
-	}
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		val = gsw->mii_read(gsw, i, MII_BMCR);
-		val |= BMCR_PDOWN;
-		gsw->mii_write(gsw, i, MII_BMCR, val);
-	}
-
-	/* Force MAC link down before reset */
-	mt753x_reg_write(gsw, PMCR(5), FORCE_MODE);
-	mt753x_reg_write(gsw, PMCR(6), FORCE_MODE);
-
-	/* Switch soft reset */
-	/* BUG: sw reset causes gsw int flooding */
-	mt753x_reg_write(gsw, SYS_CTRL, SW_PHY_RST | SW_SYS_RST | SW_REG_RST);
-	usleep_range(10, 20);
-
-	/* global mac control settings configuration */
-	mt753x_reg_write(gsw, GMACCR,
-			 LATE_COL_DROP | (15 << MTCC_LMT_S) |
-			 (2 << MAX_RX_JUMBO_S) | RX_PKT_LEN_MAX_JUMBO);
-
-	mt7530_core_pll_setup(gsw);
-	mt7530_mac_port_setup(gsw);
-
-	return 0;
-}
-
-static int mt7530_sw_post_init(struct gsw_mt753x *gsw)
-{
-	int i;
-	u32 val;
-
-	mt7530_phy_setting(gsw);
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		val = gsw->mii_read(gsw, i, MII_BMCR);
-		val &= ~BMCR_PDOWN;
-		gsw->mii_write(gsw, i, MII_BMCR, val);
-	}
-
-	return 0;
-}
-
-struct mt753x_sw_id mt7530_id = {
-	.model = MT7530,
-	.detect = mt7530_sw_detect,
-	.init = mt7530_sw_init,
-	.post_init = mt7530_sw_post_init
-};
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7530.h b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7530.h
deleted file mode 100644
index 40243d4e5a..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7530.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2018 MediaTek Inc.
- */
-
-#ifndef _MT7530_H_
-#define _MT7530_H_
-
-#include "mt753x.h"
-
-extern struct mt753x_sw_id mt7530_id;
-
-#endif /* _MT7530_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7531.c b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7531.c
deleted file mode 100644
index 7ebf09c102..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7531.c
+++ /dev/null
@@ -1,918 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Zhanguo Ju <zhanguo.ju@mediatek.com>
- */
-
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/hrtimer.h>
-
-#include "mt753x.h"
-#include "mt753x_regs.h"
-
-/* MT7531 registers */
-#define SGMII_REG_BASE			0x5000
-#define SGMII_REG_PORT_BASE		0x1000
-#define SGMII_REG(p, r)			(SGMII_REG_BASE + \
-					(p) * SGMII_REG_PORT_BASE + (r))
-#define PCS_CONTROL_1(p)		SGMII_REG(p, 0x00)
-#define SGMII_MODE(p)			SGMII_REG(p, 0x20)
-#define QPHY_PWR_STATE_CTRL(p)		SGMII_REG(p, 0xe8)
-#define PHYA_CTRL_SIGNAL3(p)		SGMII_REG(p, 0x128)
-
-/* Fields of PCS_CONTROL_1 */
-#define SGMII_LINK_STATUS		BIT(18)
-#define SGMII_AN_ENABLE			BIT(12)
-#define SGMII_AN_RESTART		BIT(9)
-
-/* Fields of SGMII_MODE */
-#define SGMII_REMOTE_FAULT_DIS		BIT(8)
-#define SGMII_IF_MODE_FORCE_DUPLEX	BIT(4)
-#define SGMII_IF_MODE_FORCE_SPEED_S	0x2
-#define SGMII_IF_MODE_FORCE_SPEED_M	0x0c
-#define SGMII_IF_MODE_ADVERT_AN		BIT(1)
-
-/* Values of SGMII_IF_MODE_FORCE_SPEED */
-#define SGMII_IF_MODE_FORCE_SPEED_10	0
-#define SGMII_IF_MODE_FORCE_SPEED_100	1
-#define SGMII_IF_MODE_FORCE_SPEED_1000	2
-
-/* Fields of QPHY_PWR_STATE_CTRL */
-#define PHYA_PWD			BIT(4)
-
-/* Fields of PHYA_CTRL_SIGNAL3 */
-#define RG_TPHY_SPEED_S			2
-#define RG_TPHY_SPEED_M			0x0c
-
-/* Values of RG_TPHY_SPEED */
-#define RG_TPHY_SPEED_1000		0
-#define RG_TPHY_SPEED_2500		1
-
-/* Unique fields of (M)HWSTRAP for MT7531 */
-#define XTAL_FSEL_S			7
-#define XTAL_FSEL_M			BIT(7)
-#define PHY_EN				BIT(6)
-#define CHG_STRAP			BIT(8)
-
-/* Efuse Register Define */
-#define GBE_EFUSE			0x7bc8
-#define GBE_SEL_EFUSE_EN		BIT(0)
-
-/* PHY ENABLE Register bitmap define */
-#define PHY_DEV1F			0x1f
-#define PHY_DEV1F_REG_44		0x44
-#define PHY_DEV1F_REG_104		0x104
-#define PHY_DEV1F_REG_10A		0x10a
-#define PHY_DEV1F_REG_10B		0x10b
-#define PHY_DEV1F_REG_10C		0x10c
-#define PHY_DEV1F_REG_10D		0x10d
-#define PHY_DEV1F_REG_268		0x268
-#define PHY_DEV1F_REG_269		0x269
-#define PHY_DEV1F_REG_403		0x403
-
-/* Fields of PHY_DEV1F_REG_403 */
-#define GBE_EFUSE_SETTING		BIT(3)
-#define PHY_EN_BYPASS_MODE		BIT(4)
-#define POWER_ON_OFF			BIT(5)
-#define PHY_PLL_M			GENMASK(9, 8)
-#define PHY_PLL_SEL(x)			(((x) << 8) & GENMASK(9, 8))
-
-/* PHY EEE Register bitmap of define */
-#define PHY_DEV07			0x07
-#define PHY_DEV07_REG_03C		0x3c
-
-/* PHY Extend Register 0x14 bitmap of define */
-#define PHY_EXT_REG_14			0x14
-
-/* Fields of PHY_EXT_REG_14 */
-#define PHY_EN_DOWN_SHFIT		BIT(4)
-
-/* PHY Extend Register 0x17 bitmap of define */
-#define PHY_EXT_REG_17			0x17
-
-/* Fields of PHY_EXT_REG_17 */
-#define PHY_LINKDOWN_POWER_SAVING_EN	BIT(4)
-
-/* PHY Token Ring Register 0x10 bitmap of define */
-#define PHY_TR_REG_10			0x10
-
-/* PHY Token Ring Register 0x12 bitmap of define */
-#define PHY_TR_REG_12			0x12
-
-/* PHY DEV 0x1e Register bitmap of define */
-#define PHY_DEV1E			0x1e
-#define PHY_DEV1E_REG_13		0x13
-#define PHY_DEV1E_REG_14		0x14
-#define PHY_DEV1E_REG_41		0x41
-#define PHY_DEV1E_REG_A6		0xa6
-#define PHY_DEV1E_REG_0C6		0x0c6
-#define PHY_DEV1E_REG_0FE		0x0fe
-#define PHY_DEV1E_REG_123		0x123
-#define PHY_DEV1E_REG_189		0x189
-
-/* Fields of PHY_DEV1E_REG_0C6 */
-#define PHY_POWER_SAVING_S		8
-#define PHY_POWER_SAVING_M		0x300
-#define PHY_POWER_SAVING_TX		0x0
-
-/* Fields of PHY_DEV1E_REG_189 */
-#define DESCRAMBLER_CLEAR_EN		0x1
-
-/* Values of XTAL_FSEL_S */
-#define XTAL_40MHZ			0
-#define XTAL_25MHZ			1
-
-#define PLLGP_EN			0x7820
-#define EN_COREPLL			BIT(2)
-#define SW_CLKSW			BIT(1)
-#define SW_PLLGP			BIT(0)
-
-#define PLLGP_CR0			0x78a8
-#define RG_COREPLL_EN			BIT(22)
-#define RG_COREPLL_POSDIV_S		23
-#define RG_COREPLL_POSDIV_M		0x3800000
-#define RG_COREPLL_SDM_PCW_S		1
-#define RG_COREPLL_SDM_PCW_M		0x3ffffe
-#define RG_COREPLL_SDM_PCW_CHG		BIT(0)
-
-/* TOP Signals Status Register */
-#define TOP_SIG_SR			0x780c
-#define PAD_DUAL_SGMII_EN		BIT(1)
-
-/* RGMII and SGMII PLL clock */
-#define ANA_PLLGP_CR2			0x78b0
-#define ANA_PLLGP_CR5			0x78bc
-
-/* GPIO mode define */
-#define GPIO_MODE_REGS(x)		(0x7c0c + (((x) / 8) * 4))
-#define GPIO_MODE_S			4
-
-/* GPIO GROUP IOLB SMT0 Control */
-#define SMT0_IOLB			0x7f04
-#define SMT_IOLB_5_SMI_MDC_EN		BIT(5)
-
-/* Unique fields of PMCR for MT7531 */
-#define FORCE_MODE_EEE1G		BIT(25)
-#define FORCE_MODE_EEE100		BIT(26)
-#define FORCE_MODE_TX_FC		BIT(27)
-#define FORCE_MODE_RX_FC		BIT(28)
-#define FORCE_MODE_DPX			BIT(29)
-#define FORCE_MODE_SPD			BIT(30)
-#define FORCE_MODE_LNK			BIT(31)
-#define FORCE_MODE			BIT(15)
-
-#define CHIP_REV			0x781C
-#define CHIP_NAME_S			16
-#define CHIP_NAME_M			0xffff0000
-#define CHIP_REV_S			0
-#define CHIP_REV_M			0x0f
-#define CHIP_REV_E1			0x0
-
-#define CLKGEN_CTRL			0x7500
-#define CLK_SKEW_OUT_S			8
-#define CLK_SKEW_OUT_M			0x300
-#define CLK_SKEW_IN_S			6
-#define CLK_SKEW_IN_M			0xc0
-#define RXCLK_NO_DELAY			BIT(5)
-#define TXCLK_NO_REVERSE		BIT(4)
-#define GP_MODE_S			1
-#define GP_MODE_M			0x06
-#define GP_CLK_EN			BIT(0)
-
-/* Values of GP_MODE */
-#define GP_MODE_RGMII			0
-#define GP_MODE_MII			1
-#define GP_MODE_REV_MII			2
-
-/* Values of CLK_SKEW_IN */
-#define CLK_SKEW_IN_NO_CHANGE		0
-#define CLK_SKEW_IN_DELAY_100PPS	1
-#define CLK_SKEW_IN_DELAY_200PPS	2
-#define CLK_SKEW_IN_REVERSE		3
-
-/* Values of CLK_SKEW_OUT */
-#define CLK_SKEW_OUT_NO_CHANGE		0
-#define CLK_SKEW_OUT_DELAY_100PPS	1
-#define CLK_SKEW_OUT_DELAY_200PPS	2
-#define CLK_SKEW_OUT_REVERSE		3
-
-/* Proprietory Control Register of Internal Phy device 0x1e */
-#define RXADC_CONTROL_3			0xc2
-#define RXADC_LDO_CONTROL_2		0xd3
-
-/* Proprietory Control Register of Internal Phy device 0x1f */
-#define TXVLD_DA_271			0x271
-#define TXVLD_DA_272			0x272
-#define TXVLD_DA_273			0x273
-
-/* DSP Channel and NOD_ADDR*/
-#define DSP_CH				0x2
-#define DSP_NOD_ADDR			0xD
-
-/* gpio pinmux pins and functions define */
-static int gpio_int_pins[] = {0};
-static int gpio_int_funcs[] = {1};
-static int gpio_mdc_pins[] = {11, 20};
-static int gpio_mdc_funcs[] = {2, 2};
-static int gpio_mdio_pins[] = {12, 21};
-static int gpio_mdio_funcs[] = {2, 2};
-
-static int mt7531_set_port_sgmii_force_mode(struct gsw_mt753x *gsw, u32 port,
-					    struct mt753x_port_cfg *port_cfg)
-{
-	u32 speed, port_base, val;
-	ktime_t timeout;
-	u32 timeout_us;
-
-	if (port < 5 || port >= MT753X_NUM_PORTS) {
-		dev_info(gsw->dev, "port %d is not a SGMII port\n", port);
-		return -EINVAL;
-	}
-
-	port_base = port - 5;
-
-	switch (port_cfg->speed) {
-	case MAC_SPD_1000:
-		speed = RG_TPHY_SPEED_1000;
-		break;
-	case MAC_SPD_2500:
-		speed = RG_TPHY_SPEED_2500;
-		break;
-	default:
-		dev_info(gsw->dev, "invalid SGMII speed idx %d for port %d\n",
-			 port_cfg->speed, port);
-
-		speed = RG_TPHY_SPEED_1000;
-	}
-
-	/* Step 1: Speed select register setting */
-	val = mt753x_reg_read(gsw, PHYA_CTRL_SIGNAL3(port_base));
-	val &= ~RG_TPHY_SPEED_M;
-	val |= speed << RG_TPHY_SPEED_S;
-	mt753x_reg_write(gsw, PHYA_CTRL_SIGNAL3(port_base), val);
-
-	/* Step 2 : Disable AN */
-	val = mt753x_reg_read(gsw, PCS_CONTROL_1(port_base));
-	val &= ~SGMII_AN_ENABLE;
-	mt753x_reg_write(gsw, PCS_CONTROL_1(port_base), val);
-
-	/* Step 3: SGMII force mode setting */
-	val = mt753x_reg_read(gsw, SGMII_MODE(port_base));
-	val &= ~SGMII_IF_MODE_ADVERT_AN;
-	val &= ~SGMII_IF_MODE_FORCE_SPEED_M;
-	val |= SGMII_IF_MODE_FORCE_SPEED_1000 << SGMII_IF_MODE_FORCE_SPEED_S;
-	val |= SGMII_IF_MODE_FORCE_DUPLEX;
-	/* For sgmii force mode, 0 is full duplex and 1 is half duplex */
-	if (port_cfg->duplex)
-		val &= ~SGMII_IF_MODE_FORCE_DUPLEX;
-
-	mt753x_reg_write(gsw, SGMII_MODE(port_base), val);
-
-	/* Step 4: XXX: Disable Link partner's AN and set force mode */
-
-	/* Step 5: XXX: Special setting for PHYA ==> reserved for flexible */
-
-	/* Step 6 : Release PHYA power down state */
-	val = mt753x_reg_read(gsw, QPHY_PWR_STATE_CTRL(port_base));
-	val &= ~PHYA_PWD;
-	mt753x_reg_write(gsw, QPHY_PWR_STATE_CTRL(port_base), val);
-
-	/* Step 7 : Polling SGMII_LINK_STATUS */
-	timeout_us = 2000000;
-	timeout = ktime_add_us(ktime_get(), timeout_us);
-	while (1) {
-		val = mt753x_reg_read(gsw, PCS_CONTROL_1(port_base));
-		val &= SGMII_LINK_STATUS;
-
-		if (val)
-			break;
-
-		if (ktime_compare(ktime_get(), timeout) > 0)
-			return -ETIMEDOUT;
-	}
-
-	return 0;
-}
-
-static int mt7531_set_port_sgmii_an_mode(struct gsw_mt753x *gsw, u32 port,
-					 struct mt753x_port_cfg *port_cfg)
-{
-	u32 speed, port_base, val;
-	ktime_t timeout;
-	u32 timeout_us;
-
-	if (port < 5 || port >= MT753X_NUM_PORTS) {
-		dev_info(gsw->dev, "port %d is not a SGMII port\n", port);
-		return -EINVAL;
-	}
-
-	port_base = port - 5;
-
-	switch (port_cfg->speed) {
-	case MAC_SPD_1000:
-		speed = RG_TPHY_SPEED_1000;
-		break;
-	case MAC_SPD_2500:
-		speed = RG_TPHY_SPEED_2500;
-		break;
-	default:
-		dev_info(gsw->dev, "invalid SGMII speed idx %d for port %d\n",
-			 port_cfg->speed, port);
-
-		speed = RG_TPHY_SPEED_1000;
-	}
-
-	/* Step 1: Speed select register setting */
-	val = mt753x_reg_read(gsw, PHYA_CTRL_SIGNAL3(port_base));
-	val &= ~RG_TPHY_SPEED_M;
-	val |= speed << RG_TPHY_SPEED_S;
-	mt753x_reg_write(gsw, PHYA_CTRL_SIGNAL3(port_base), val);
-
-	/* Step 2: Remote fault disable */
-	val = mt753x_reg_read(gsw, SGMII_MODE(port));
-	val |= SGMII_REMOTE_FAULT_DIS;
-	mt753x_reg_write(gsw, SGMII_MODE(port), val);
-
-	/* Step 3: Setting Link partner's AN enable = 1 */
-
-	/* Step 4: Setting Link partner's device ability for speed/duplex */
-
-	/* Step 5: AN re-start */
-	val = mt753x_reg_read(gsw, PCS_CONTROL_1(port));
-	val |= SGMII_AN_RESTART;
-	mt753x_reg_write(gsw, PCS_CONTROL_1(port), val);
-
-	/* Step 6: Special setting for PHYA ==> reserved for flexible */
-
-	/* Step 7 : Polling SGMII_LINK_STATUS */
-	timeout_us = 2000000;
-	timeout = ktime_add_us(ktime_get(), timeout_us);
-	while (1) {
-		val = mt753x_reg_read(gsw, PCS_CONTROL_1(port_base));
-		val &= SGMII_LINK_STATUS;
-
-		if (val)
-			break;
-
-		if (ktime_compare(ktime_get(), timeout) > 0)
-			return -ETIMEDOUT;
-	}
-
-	return 0;
-}
-
-static int mt7531_set_port_rgmii(struct gsw_mt753x *gsw, u32 port)
-{
-	u32 val;
-
-	if (port != 5) {
-		dev_info(gsw->dev, "RGMII mode is not available for port %d\n",
-			 port);
-		return -EINVAL;
-	}
-
-	val = mt753x_reg_read(gsw, CLKGEN_CTRL);
-	val |= GP_CLK_EN;
-	val &= ~GP_MODE_M;
-	val |= GP_MODE_RGMII << GP_MODE_S;
-	val |= TXCLK_NO_REVERSE;
-	val |= RXCLK_NO_DELAY;
-	val &= ~CLK_SKEW_IN_M;
-	val |= CLK_SKEW_IN_NO_CHANGE << CLK_SKEW_IN_S;
-	val &= ~CLK_SKEW_OUT_M;
-	val |= CLK_SKEW_OUT_NO_CHANGE << CLK_SKEW_OUT_S;
-	mt753x_reg_write(gsw, CLKGEN_CTRL, val);
-
-	return 0;
-}
-
-static int mt7531_mac_port_setup(struct gsw_mt753x *gsw, u32 port,
-				 struct mt753x_port_cfg *port_cfg)
-{
-	u32 pmcr;
-	u32 speed;
-
-	if (port < 5 || port >= MT753X_NUM_PORTS) {
-		dev_info(gsw->dev, "port %d is not a MAC port\n", port);
-		return -EINVAL;
-	}
-
-	if (port_cfg->enabled) {
-		pmcr = (IPG_96BIT_WITH_SHORT_IPG << IPG_CFG_S) |
-		       MAC_MODE | MAC_TX_EN | MAC_RX_EN |
-		       BKOFF_EN | BACKPR_EN;
-
-		if (port_cfg->force_link) {
-			/* PMCR's speed field 0x11 is reserved,
-			 * sw should set 0x10
-			 */
-			speed = port_cfg->speed;
-			if (port_cfg->speed == MAC_SPD_2500)
-				speed = MAC_SPD_1000;
-
-			pmcr |= FORCE_MODE_LNK | FORCE_LINK |
-				FORCE_MODE_SPD | FORCE_MODE_DPX |
-				FORCE_MODE_RX_FC | FORCE_MODE_TX_FC |
-				FORCE_RX_FC | FORCE_TX_FC |
-				(speed << FORCE_SPD_S);
-
-			if (port_cfg->duplex)
-				pmcr |= FORCE_DPX;
-		}
-	} else {
-		pmcr = FORCE_MODE_LNK;
-	}
-
-	switch (port_cfg->phy_mode) {
-	case PHY_INTERFACE_MODE_RGMII:
-		mt7531_set_port_rgmii(gsw, port);
-		break;
-	case PHY_INTERFACE_MODE_SGMII:
-		if (port_cfg->force_link)
-			mt7531_set_port_sgmii_force_mode(gsw, port, port_cfg);
-		else
-			mt7531_set_port_sgmii_an_mode(gsw, port, port_cfg);
-		break;
-	default:
-		if (port_cfg->enabled)
-			dev_info(gsw->dev, "%s is not supported by port %d\n",
-				 phy_modes(port_cfg->phy_mode), port);
-
-		pmcr = FORCE_MODE_LNK;
-	}
-
-	mt753x_reg_write(gsw, PMCR(port), pmcr);
-
-	return 0;
-}
-
-static void mt7531_core_pll_setup(struct gsw_mt753x *gsw)
-{
-	u32 hwstrap;
-	u32 val;
-
-	val = mt753x_reg_read(gsw, TOP_SIG_SR);
-	if (val & PAD_DUAL_SGMII_EN)
-		return;
-
-	hwstrap = mt753x_reg_read(gsw, HWSTRAP);
-
-	switch ((hwstrap & XTAL_FSEL_M) >> XTAL_FSEL_S) {
-	case XTAL_25MHZ:
-		/* Step 1 : Disable MT7531 COREPLL */
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val &= ~EN_COREPLL;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-
-		/* Step 2: switch to XTAL output */
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val |= SW_CLKSW;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_EN;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		/* Step 3: disable PLLGP and enable program PLLGP */
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val |= SW_PLLGP;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-
-		/* Step 4: program COREPLL output frequency to 500MHz */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_POSDIV_M;
-		val |= 2 << RG_COREPLL_POSDIV_S;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-		usleep_range(25, 35);
-
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_SDM_PCW_M;
-		val |= 0x140000 << RG_COREPLL_SDM_PCW_S;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		/* Set feedback divide ratio update signal to high */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val |= RG_COREPLL_SDM_PCW_CHG;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-		/* Wait for at least 16 XTAL clocks */
-		usleep_range(10, 20);
-
-		/* Step 5: set feedback divide ratio update signal to low */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_SDM_PCW_CHG;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		/* Enable 325M clock for SGMII */
-		mt753x_reg_write(gsw, ANA_PLLGP_CR5, 0xad0000);
-
-		/* Enable 250SSC clock for RGMII */
-		mt753x_reg_write(gsw, ANA_PLLGP_CR2, 0x4f40000);
-
-		/* Step 6: Enable MT7531 PLL */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val |= RG_COREPLL_EN;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val |= EN_COREPLL;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-		usleep_range(25, 35);
-
-		break;
-	case XTAL_40MHZ:
-		/* Step 1 : Disable MT7531 COREPLL */
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val &= ~EN_COREPLL;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-
-		/* Step 2: switch to XTAL output */
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val |= SW_CLKSW;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_EN;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		/* Step 3: disable PLLGP and enable program PLLGP */
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val |= SW_PLLGP;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-
-		/* Step 4: program COREPLL output frequency to 500MHz */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_POSDIV_M;
-		val |= 2 << RG_COREPLL_POSDIV_S;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-		usleep_range(25, 35);
-
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_SDM_PCW_M;
-		val |= 0x190000 << RG_COREPLL_SDM_PCW_S;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		/* Set feedback divide ratio update signal to high */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val |= RG_COREPLL_SDM_PCW_CHG;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-		/* Wait for at least 16 XTAL clocks */
-		usleep_range(10, 20);
-
-		/* Step 5: set feedback divide ratio update signal to low */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val &= ~RG_COREPLL_SDM_PCW_CHG;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		/* Enable 325M clock for SGMII */
-		mt753x_reg_write(gsw, ANA_PLLGP_CR5, 0xad0000);
-
-		/* Enable 250SSC clock for RGMII */
-		mt753x_reg_write(gsw, ANA_PLLGP_CR2, 0x4f40000);
-
-		/* Step 6: Enable MT7531 PLL */
-		val = mt753x_reg_read(gsw, PLLGP_CR0);
-		val |= RG_COREPLL_EN;
-		mt753x_reg_write(gsw, PLLGP_CR0, val);
-
-		val = mt753x_reg_read(gsw, PLLGP_EN);
-		val |= EN_COREPLL;
-		mt753x_reg_write(gsw, PLLGP_EN, val);
-		usleep_range(25, 35);
-		break;
-	}
-}
-
-static int mt7531_internal_phy_calibration(struct gsw_mt753x *gsw)
-{
-	return 0;
-}
-
-static int mt7531_sw_detect(struct gsw_mt753x *gsw, struct chip_rev *crev)
-{
-	u32 rev, topsig;
-
-	rev = mt753x_reg_read(gsw, CHIP_REV);
-
-	if (((rev & CHIP_NAME_M) >> CHIP_NAME_S) == MT7531) {
-		if (crev) {
-			topsig = mt753x_reg_read(gsw, TOP_SIG_SR);
-
-			crev->rev = rev & CHIP_REV_M;
-			crev->name = topsig & PAD_DUAL_SGMII_EN ?
-				     "MT7531AE" : "MT7531BE";
-		}
-
-		return 0;
-	}
-
-	return -ENODEV;
-}
-
-static void pinmux_set_mux_7531(struct gsw_mt753x *gsw, u32 pin, u32 mode)
-{
-	u32 val;
-
-	val = mt753x_reg_read(gsw, GPIO_MODE_REGS(pin));
-	val &= ~(0xf << (pin & 7) * GPIO_MODE_S);
-	val |= mode << (pin & 7) * GPIO_MODE_S;
-	mt753x_reg_write(gsw, GPIO_MODE_REGS(pin), val);
-}
-
-static int mt7531_set_gpio_pinmux(struct gsw_mt753x *gsw)
-{
-	u32 group = 0;
-	struct device_node *np = gsw->dev->of_node;
-
-	/* Set GPIO 0 interrupt mode */
-	pinmux_set_mux_7531(gsw, gpio_int_pins[0], gpio_int_funcs[0]);
-
-	of_property_read_u32(np, "mediatek,mdio_master_pinmux", &group);
-
-	/* group = 0: do nothing, 1: 1st group (AE), 2: 2nd group (BE) */
-	if (group > 0 && group <= 2) {
-		group--;
-		pinmux_set_mux_7531(gsw, gpio_mdc_pins[group],
-				    gpio_mdc_funcs[group]);
-		pinmux_set_mux_7531(gsw, gpio_mdio_pins[group],
-				    gpio_mdio_funcs[group]);
-	}
-
-	return 0;
-}
-
-static void mt7531_phy_pll_setup(struct gsw_mt753x *gsw)
-{
-	u32 hwstrap;
-	u32 val;
-
-	hwstrap = mt753x_reg_read(gsw, HWSTRAP);
-
-	switch ((hwstrap & XTAL_FSEL_M) >> XTAL_FSEL_S) {
-	case XTAL_25MHZ:
-		/* disable pll auto calibration */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_104, 0x608);
-
-		/* change pll sel */
-		val = gsw->mmd_read(gsw, 0, PHY_DEV1F,
-				     PHY_DEV1F_REG_403);
-		val &= ~(PHY_PLL_M);
-		val |= PHY_PLL_SEL(3);
-		gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_403, val);
-
-		/* set divider ratio */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F,
-			       PHY_DEV1F_REG_10A, 0x1009);
-
-		/* set divider ratio */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_10B, 0x7c6);
-
-		/* capacitance and resistance adjustment */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F,
-			       PHY_DEV1F_REG_10C, 0xa8be);
-
-		break;
-	case XTAL_40MHZ:
-		/* disable pll auto calibration */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_104, 0x608);
-
-		/* change pll sel */
-		val = gsw->mmd_read(gsw, 0, PHY_DEV1F,
-				     PHY_DEV1F_REG_403);
-		val &= ~(PHY_PLL_M);
-		val |= PHY_PLL_SEL(3);
-		gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_403, val);
-
-		/* set divider ratio */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F,
-			       PHY_DEV1F_REG_10A, 0x1018);
-
-		/* set divider ratio */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_10B, 0xc676);
-
-		/* capacitance and resistance adjustment */
-		gsw->mmd_write(gsw, 0, PHY_DEV1F,
-			       PHY_DEV1F_REG_10C, 0xd8be);
-		break;
-	}
-
-	/* power down pll. additional delay is not required via mdio access */
-	gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_10D, 0x10);
-
-	/* power up pll */
-	gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_10D, 0x14);
-}
-
-static void mt7531_phy_setting(struct gsw_mt753x *gsw)
-{
-	int i;
-	u32 val;
-
-	/* Adjust DAC TX Delay */
-	gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_44, 0xc0);
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		/* Disable EEE */
-		gsw->mmd_write(gsw, i, PHY_DEV07, PHY_DEV07_REG_03C, 0);
-
-		/* Enable HW auto downshift */
-		gsw->mii_write(gsw, i, 0x1f, 0x1);
-		val = gsw->mii_read(gsw, i, PHY_EXT_REG_14);
-		val |= PHY_EN_DOWN_SHFIT;
-		gsw->mii_write(gsw, i, PHY_EXT_REG_14, val);
-
-		/* Increase SlvDPSready time */
-		gsw->mii_write(gsw, i, 0x1f, 0x52b5);
-		gsw->mii_write(gsw, i, PHY_TR_REG_10, 0xafae);
-		gsw->mii_write(gsw, i, PHY_TR_REG_12, 0x2f);
-		gsw->mii_write(gsw, i, PHY_TR_REG_10, 0x8fae);
-		gsw->mii_write(gsw, i, 0x1f, 0);
-
-		/* Adjust 100_mse_threshold */
-		gsw->mmd_write(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_123, 0xffff);
-
-		/* Disable mcc */
-		gsw->mmd_write(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_A6, 0x300);
-
-		/* PHY link down power saving enable */
-		val = gsw->mii_read(gsw, i, PHY_EXT_REG_17);
-		val |= PHY_LINKDOWN_POWER_SAVING_EN;
-		gsw->mii_write(gsw, i, PHY_EXT_REG_17, val);
-
-		val = gsw->mmd_read(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_0C6);
-		val &= ~PHY_POWER_SAVING_M;
-		val |= PHY_POWER_SAVING_TX << PHY_POWER_SAVING_S;
-		gsw->mmd_write(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_0C6, val);
-
-		/* Set TX Pair delay selection */
-		gsw->mmd_write(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_13, 0x404);
-		gsw->mmd_write(gsw, i, PHY_DEV1E, PHY_DEV1E_REG_14, 0x404);
-	}
-}
-
-static void mt7531_adjust_line_driving(struct gsw_mt753x *gsw, u32 port)
-{
-	/* For ADC timing margin window for LDO calibration */
-	gsw->mmd_write(gsw, port, PHY_DEV1E, RXADC_LDO_CONTROL_2, 0x2222);
-
-	/* Adjust AD sample timing */
-	gsw->mmd_write(gsw, port, PHY_DEV1E, RXADC_CONTROL_3, 0x4444);
-
-	/* Adjust Line driver current for different mode */
-	gsw->mmd_write(gsw, port, PHY_DEV1F, TXVLD_DA_271, 0x2ca5);
-
-	/* Adjust Line driver current for different mode */
-	gsw->mmd_write(gsw, port, PHY_DEV1F, TXVLD_DA_272, 0xc6b);
-
-	/* Adjust Line driver amplitude for 10BT */
-	gsw->mmd_write(gsw, port, PHY_DEV1F, TXVLD_DA_273, 0x3000);
-
-	/* Adjust RX Echo path filter */
-	gsw->mmd_write(gsw, port, PHY_DEV1E, PHY_DEV1E_REG_0FE, 0x2);
-
-	/* Adjust RX HVGA bias current */
-	gsw->mmd_write(gsw, port, PHY_DEV1E, PHY_DEV1E_REG_41, 0x3333);
-
-	/* Adjust TX class AB driver 1 */
-	gsw->mmd_write(gsw, port, PHY_DEV1F, PHY_DEV1F_REG_268, 0x388);
-
-	/* Adjust TX class AB driver 2 */
-	gsw->mmd_write(gsw, port, PHY_DEV1F, PHY_DEV1F_REG_269, 0x4448);
-}
-
-static void mt7531_eee_setting(struct gsw_mt753x *gsw, u32 port)
-{
-	u32 tr_reg_control;
-	u32 val;
-
-	/* Disable generate signal to clear the scramble_lock when lpi mode */
-	val = gsw->mmd_read(gsw, port, PHY_DEV1E, PHY_DEV1E_REG_189);
-	val &= ~DESCRAMBLER_CLEAR_EN;
-	gsw->mmd_write(gsw, port, PHY_DEV1E, PHY_DEV1E_REG_189, val);
-
-	/* roll back CR*/
-	gsw->mii_write(gsw, port, 0x1f, 0x52b5);
-	gsw->mmd_write(gsw, port, 0x1e, 0x2d1, 0);
-	tr_reg_control = (1 << 15) | (0 << 13) | (DSP_CH << 11) |
-			 (DSP_NOD_ADDR << 7) | (0x8 << 1);
-	gsw->mii_write(gsw, port, 17, 0x1b);
-	gsw->mii_write(gsw, port, 18, 0);
-	gsw->mii_write(gsw, port, 16, tr_reg_control);
-	tr_reg_control = (1 << 15) | (0 << 13) | (DSP_CH << 11) |
-			 (DSP_NOD_ADDR << 7) | (0xf << 1);
-	gsw->mii_write(gsw, port, 17, 0);
-	gsw->mii_write(gsw, port, 18, 0);
-	gsw->mii_write(gsw, port, 16, tr_reg_control);
-
-	tr_reg_control = (1 << 15) | (0 << 13) | (DSP_CH << 11) |
-			 (DSP_NOD_ADDR << 7) | (0x10 << 1);
-	gsw->mii_write(gsw, port, 17, 0x500);
-	gsw->mii_write(gsw, port, 18, 0);
-	gsw->mii_write(gsw, port, 16, tr_reg_control);
-	gsw->mii_write(gsw, port, 0x1f, 0);
-}
-
-static int mt7531_sw_init(struct gsw_mt753x *gsw)
-{
-	int i;
-	u32 val;
-
-	gsw->phy_base = (gsw->smi_addr + 1) & MT753X_SMI_ADDR_MASK;
-
-	gsw->mii_read = mt753x_mii_read;
-	gsw->mii_write = mt753x_mii_write;
-	gsw->mmd_read = mt753x_mmd_read;
-	gsw->mmd_write = mt753x_mmd_write;
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		val = gsw->mii_read(gsw, i, MII_BMCR);
-		val |= BMCR_ISOLATE;
-		gsw->mii_write(gsw, i, MII_BMCR, val);
-	}
-
-	/* Force MAC link down before reset */
-	mt753x_reg_write(gsw, PMCR(5), FORCE_MODE_LNK);
-	mt753x_reg_write(gsw, PMCR(6), FORCE_MODE_LNK);
-
-	/* Switch soft reset */
-	mt753x_reg_write(gsw, SYS_CTRL, SW_SYS_RST | SW_REG_RST);
-	usleep_range(10, 20);
-
-	/* Enable MDC input Schmitt Trigger */
-	val = mt753x_reg_read(gsw, SMT0_IOLB);
-	mt753x_reg_write(gsw, SMT0_IOLB, val | SMT_IOLB_5_SMI_MDC_EN);
-
-	/* Set 7531 gpio pinmux */
-	mt7531_set_gpio_pinmux(gsw);
-
-	/* Global mac control settings */
-	mt753x_reg_write(gsw, GMACCR,
-			 (15 << MTCC_LMT_S) | (11 << MAX_RX_JUMBO_S) |
-			 RX_PKT_LEN_MAX_JUMBO);
-
-	mt7531_core_pll_setup(gsw);
-	mt7531_mac_port_setup(gsw, 5, &gsw->port5_cfg);
-	mt7531_mac_port_setup(gsw, 6, &gsw->port6_cfg);
-
-	return 0;
-}
-
-static int mt7531_sw_post_init(struct gsw_mt753x *gsw)
-{
-	int i;
-	u32 val;
-
-	mt7531_phy_pll_setup(gsw);
-
-	/* Internal PHYs are disabled by default. SW should enable them.
-	 * Note that this may already be enabled in bootloader stage.
-	 */
-	val = gsw->mmd_read(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_403);
-	val |= PHY_EN_BYPASS_MODE;
-	val &= ~POWER_ON_OFF;
-	gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_403, val);
-
-	mt7531_phy_setting(gsw);
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		val = gsw->mii_read(gsw, i, MII_BMCR);
-		val &= ~BMCR_ISOLATE;
-		gsw->mii_write(gsw, i, MII_BMCR, val);
-	}
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++)
-		mt7531_adjust_line_driving(gsw, i);
-
-	for (i = 0; i < MT753X_NUM_PHYS; i++)
-		mt7531_eee_setting(gsw, i);
-
-	val = mt753x_reg_read(gsw, CHIP_REV);
-	val &= CHIP_REV_M;
-	if (val == CHIP_REV_E1) {
-		mt7531_internal_phy_calibration(gsw);
-	} else {
-		val = mt753x_reg_read(gsw, GBE_EFUSE);
-		if (val & GBE_SEL_EFUSE_EN) {
-			val = gsw->mmd_read(gsw, 0, PHY_DEV1F,
-					    PHY_DEV1F_REG_403);
-			val &= ~GBE_EFUSE_SETTING;
-			gsw->mmd_write(gsw, 0, PHY_DEV1F, PHY_DEV1F_REG_403,
-				       val);
-		} else {
-			mt7531_internal_phy_calibration(gsw);
-		}
-	}
-
-	return 0;
-}
-
-struct mt753x_sw_id mt7531_id = {
-	.model = MT7531,
-	.detect = mt7531_sw_detect,
-	.init = mt7531_sw_init,
-	.post_init = mt7531_sw_post_init
-};
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Zhanguo Ju <zhanguo.ju@mediatek.com>");
-MODULE_DESCRIPTION("Driver for MediaTek MT753x Gigabit Switch");
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7531.h b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7531.h
deleted file mode 100644
index 52c8a49fd3..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt7531.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2018 MediaTek Inc.
- */
-
-#ifndef _MT7531_H_
-#define _MT7531_H_
-
-#include "mt753x.h"
-
-extern struct mt753x_sw_id mt7531_id;
-
-#endif /* _MT7531_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x.h b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x.h
deleted file mode 100644
index 837a415648..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x.h
+++ /dev/null
@@ -1,213 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-#ifndef _MT753X_H_
-#define _MT753X_H_
-
-#include <linux/list.h>
-#include <linux/mutex.h>
-#include <linux/netdevice.h>
-#include <linux/of_mdio.h>
-#include <linux/workqueue.h>
-#include <linux/gpio/consumer.h>
-
-#ifdef CONFIG_SWCONFIG
-#include <linux/switch.h>
-#endif
-
-#include "mt753x_vlan.h"
-
-#define MT753X_DFL_CPU_PORT	6
-#define MT753X_NUM_PHYS		5
-
-#define MT753X_DFL_SMI_ADDR	0x1f
-#define MT753X_SMI_ADDR_MASK	0x1f
-
-struct gsw_mt753x;
-
-enum mt753x_model {
-	MT7530 = 0x7530,
-	MT7531 = 0x7531
-};
-
-struct mt753x_port_cfg {
-	struct device_node *np;
-	int phy_mode;
-	u32 enabled: 1;
-	u32 force_link: 1;
-	u32 speed: 2;
-	u32 duplex: 1;
-};
-
-struct mt753x_phy {
-	struct gsw_mt753x *gsw;
-	struct net_device netdev;
-	struct phy_device *phydev;
-};
-
-struct gsw_mt753x {
-	u32 id;
-
-	struct device *dev;
-	struct mii_bus *host_bus;
-	struct mii_bus *gphy_bus;
-	struct mutex mii_lock;	/* MII access lock */
-	u32 smi_addr;
-	u32 phy_base;
-	int direct_phy_access;
-
-	enum mt753x_model model;
-	const char *name;
-
-	struct mt753x_port_cfg port5_cfg;
-	struct mt753x_port_cfg port6_cfg;
-
-	int phy_status_poll;
-	struct mt753x_phy phys[MT753X_NUM_PHYS];
-
-	int phy_link_sts;
-
-	int irq;
-	int reset_pin;
-	struct work_struct irq_worker;
-
-#ifdef CONFIG_SWCONFIG
-	struct switch_dev swdev;
-	u32 cpu_port;
-#endif
-
-	int global_vlan_enable;
-	struct mt753x_vlan_entry vlan_entries[MT753X_NUM_VLANS];
-	struct mt753x_port_entry port_entries[MT753X_NUM_PORTS];
-
-	int (*mii_read)(struct gsw_mt753x *gsw, int phy, int reg);
-	void (*mii_write)(struct gsw_mt753x *gsw, int phy, int reg, u16 val);
-
-	int (*mmd_read)(struct gsw_mt753x *gsw, int addr, int devad, u16 reg);
-	void (*mmd_write)(struct gsw_mt753x *gsw, int addr, int devad, u16 reg,
-			  u16 val);
-
-	struct list_head list;
-};
-
-struct chip_rev {
-	const char *name;
-	u32 rev;
-};
-
-struct mt753x_sw_id {
-	enum mt753x_model model;
-	int (*detect)(struct gsw_mt753x *gsw, struct chip_rev *crev);
-	int (*init)(struct gsw_mt753x *gsw);
-	int (*post_init)(struct gsw_mt753x *gsw);
-};
-
-extern struct list_head mt753x_devs;
-
-struct gsw_mt753x *mt753x_get_gsw(u32 id);
-struct gsw_mt753x *mt753x_get_first_gsw(void);
-void mt753x_put_gsw(void);
-void mt753x_lock_gsw(void);
-
-u32 mt753x_reg_read(struct gsw_mt753x *gsw, u32 reg);
-void mt753x_reg_write(struct gsw_mt753x *gsw, u32 reg, u32 val);
-
-int mt753x_mii_read(struct gsw_mt753x *gsw, int phy, int reg);
-void mt753x_mii_write(struct gsw_mt753x *gsw, int phy, int reg, u16 val);
-
-int mt753x_mmd_read(struct gsw_mt753x *gsw, int addr, int devad, u16 reg);
-void mt753x_mmd_write(struct gsw_mt753x *gsw, int addr, int devad, u16 reg,
-		      u16 val);
-
-int mt753x_mmd_ind_read(struct gsw_mt753x *gsw, int addr, int devad, u16 reg);
-void mt753x_mmd_ind_write(struct gsw_mt753x *gsw, int addr, int devad, u16 reg,
-			  u16 val);
-
-void mt753x_irq_worker(struct work_struct *work);
-void mt753x_irq_enable(struct gsw_mt753x *gsw);
-
-/* MDIO Indirect Access Registers */
-#define MII_MMD_ACC_CTL_REG		0x0d
-#define MMD_CMD_S			14
-#define MMD_CMD_M			0xc000
-#define MMD_DEVAD_S			0
-#define MMD_DEVAD_M			0x1f
-
-/* MMD_CMD: MMD commands */
-#define MMD_ADDR			0
-#define MMD_DATA			1
-
-#define MII_MMD_ADDR_DATA_REG		0x0e
-
-/* Procedure of MT753x Internal Register Access
- *
- * 1. Internal Register Address
- *
- *    The MT753x has a 16-bit register address and each register is 32-bit.
- *    This means the lowest two bits are not used as the register address is
- *    4-byte aligned.
- *
- *    Rest of the valid bits are divided into two parts:
- *      Bit 15..6 is the Page address
- *      Bit 5..2 is the low address
- *
- *    -------------------------------------------------------------------
- *    | 15  14  13  12  11  10   9   8   7   6 | 5   4   3   2 | 1   0  |
- *    |----------------------------------------|---------------|--------|
- *    |              Page Address              |    Address    | Unused |
- *    -------------------------------------------------------------------
- *
- * 2. MDIO access timing
- *
- *    The MT753x uses the following MDIO timing for a single register read
- *
- *      Phase 1: Write Page Address
- *    -------------------------------------------------------------------
- *    | ST | OP | PHY_ADDR | TYPE | RSVD | TA |  RSVD |    PAGE_ADDR    |
- *    -------------------------------------------------------------------
- *    | 01 | 01 |   11111  |   1  | 1111 | xx | 00000 | REG_ADDR[15..6] |
- *    -------------------------------------------------------------------
- *
- *      Phase 2: Write low Address & Read low word
- *    -------------------------------------------------------------------
- *    | ST | OP | PHY_ADDR | TYPE |    LOW_ADDR    | TA |      DATA     |
- *    -------------------------------------------------------------------
- *    | 01 | 10 |   11111  |   0  | REG_ADDR[5..2] | xx |  DATA[15..0]  |
- *    -------------------------------------------------------------------
- *
- *      Phase 3: Read high word
- *    -------------------------------------------------------------------
- *    | ST | OP | PHY_ADDR | TYPE | RSVD | TA |           DATA          |
- *    -------------------------------------------------------------------
- *    | 01 | 10 |   11111  |   1  | 0000 | xx |       DATA[31..16]      |
- *    -------------------------------------------------------------------
- *
- *    The MT753x uses the following MDIO timing for a single register write
- *
- *      Phase 1: Write Page Address (The same as read)
- *
- *      Phase 2: Write low Address and low word
- *    -------------------------------------------------------------------
- *    | ST | OP | PHY_ADDR | TYPE |    LOW_ADDR    | TA |      DATA     |
- *    -------------------------------------------------------------------
- *    | 01 | 01 |   11111  |   0  | REG_ADDR[5..2] | xx |  DATA[15..0]  |
- *    -------------------------------------------------------------------
- *
- *      Phase 3: write high word
- *    -------------------------------------------------------------------
- *    | ST | OP | PHY_ADDR | TYPE | RSVD | TA |           DATA          |
- *    -------------------------------------------------------------------
- *    | 01 | 01 |   11111  |   1  | 0000 | xx |       DATA[31..16]      |
- *    -------------------------------------------------------------------
- *
- */
-
-/* Internal Register Address fields */
-#define MT753X_REG_PAGE_ADDR_S		6
-#define MT753X_REG_PAGE_ADDR_M		0xffc0
-#define MT753X_REG_ADDR_S		2
-#define MT753X_REG_ADDR_M		0x3c
-#endif /* _MT753X_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_common.c b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_common.c
deleted file mode 100644
index 4015ddf125..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_common.c
+++ /dev/null
@@ -1,90 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-#include <linux/kernel.h>
-#include <linux/delay.h>
-
-#include "mt753x.h"
-#include "mt753x_regs.h"
-
-void mt753x_irq_enable(struct gsw_mt753x *gsw)
-{
-	u32 val;
-	int i;
-
-	/* Record initial PHY link status */
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		val = gsw->mii_read(gsw, i, MII_BMSR);
-		if (val & BMSR_LSTATUS)
-			gsw->phy_link_sts |= BIT(i);
-	}
-
-	val = BIT(MT753X_NUM_PHYS) - 1;
-
-	mt753x_reg_write(gsw, SYS_INT_EN, val);
-}
-
-static void display_port_link_status(struct gsw_mt753x *gsw, u32 port)
-{
-	u32 pmsr, speed_bits;
-	const char *speed;
-
-	pmsr = mt753x_reg_read(gsw, PMSR(port));
-
-	speed_bits = (pmsr & MAC_SPD_STS_M) >> MAC_SPD_STS_S;
-
-	switch (speed_bits) {
-	case MAC_SPD_10:
-		speed = "10Mbps";
-		break;
-	case MAC_SPD_100:
-		speed = "100Mbps";
-		break;
-	case MAC_SPD_1000:
-		speed = "1Gbps";
-		break;
-	case MAC_SPD_2500:
-		speed = "2.5Gbps";
-		break;
-	}
-
-	if (pmsr & MAC_LNK_STS) {
-		dev_info(gsw->dev, "Port %d Link is Up - %s/%s\n",
-			 port, speed, (pmsr & MAC_DPX_STS) ? "Full" : "Half");
-	} else {
-		dev_info(gsw->dev, "Port %d Link is Down\n", port);
-	}
-}
-
-void mt753x_irq_worker(struct work_struct *work)
-{
-	struct gsw_mt753x *gsw;
-	u32 sts, physts, laststs;
-	int i;
-
-	gsw = container_of(work, struct gsw_mt753x, irq_worker);
-
-	sts = mt753x_reg_read(gsw, SYS_INT_STS);
-
-	/* Check for changed PHY link status */
-	for (i = 0; i < MT753X_NUM_PHYS; i++) {
-		if (!(sts & PHY_LC_INT(i)))
-			continue;
-
-		laststs = gsw->phy_link_sts & BIT(i);
-		physts = !!(gsw->mii_read(gsw, i, MII_BMSR) & BMSR_LSTATUS);
-		physts <<= i;
-
-		if (physts ^ laststs) {
-			gsw->phy_link_sts ^= BIT(i);
-			display_port_link_status(gsw, i);
-		}
-	}
-
-	mt753x_reg_write(gsw, SYS_INT_STS, sts);
-
-	enable_irq(gsw->irq);
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_mdio.c b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_mdio.c
deleted file mode 100644
index a3f0c5d3f0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_mdio.c
+++ /dev/null
@@ -1,598 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/reset.h>
-#include <linux/hrtimer.h>
-#include <linux/mii.h>
-#include <linux/of_mdio.h>
-#include <linux/of_platform.h>
-#include <linux/of_gpio.h>
-#include <linux/of_net.h>
-#include <linux/of_irq.h>
-#include <linux/phy.h>
-
-#include "mt753x.h"
-#include "mt753x_swconfig.h"
-#include "mt753x_regs.h"
-#include "mt753x_nl.h"
-#include "mt7530.h"
-#include "mt7531.h"
-
-static u32 mt753x_id;
-struct list_head mt753x_devs;
-static DEFINE_MUTEX(mt753x_devs_lock);
-
-static struct mt753x_sw_id *mt753x_sw_ids[] = {
-	&mt7530_id,
-	&mt7531_id,
-};
-
-u32 mt753x_reg_read(struct gsw_mt753x *gsw, u32 reg)
-{
-	u32 high, low;
-
-	mutex_lock(&gsw->host_bus->mdio_lock);
-
-	gsw->host_bus->write(gsw->host_bus, gsw->smi_addr, 0x1f,
-		(reg & MT753X_REG_PAGE_ADDR_M) >> MT753X_REG_PAGE_ADDR_S);
-
-	low = gsw->host_bus->read(gsw->host_bus, gsw->smi_addr,
-		(reg & MT753X_REG_ADDR_M) >> MT753X_REG_ADDR_S);
-
-	high = gsw->host_bus->read(gsw->host_bus, gsw->smi_addr, 0x10);
-
-	mutex_unlock(&gsw->host_bus->mdio_lock);
-
-	return (high << 16) | (low & 0xffff);
-}
-
-void mt753x_reg_write(struct gsw_mt753x *gsw, u32 reg, u32 val)
-{
-	mutex_lock(&gsw->host_bus->mdio_lock);
-
-	gsw->host_bus->write(gsw->host_bus, gsw->smi_addr, 0x1f,
-		(reg & MT753X_REG_PAGE_ADDR_M) >> MT753X_REG_PAGE_ADDR_S);
-
-	gsw->host_bus->write(gsw->host_bus, gsw->smi_addr,
-		(reg & MT753X_REG_ADDR_M) >> MT753X_REG_ADDR_S, val & 0xffff);
-
-	gsw->host_bus->write(gsw->host_bus, gsw->smi_addr, 0x10, val >> 16);
-
-	mutex_unlock(&gsw->host_bus->mdio_lock);
-}
-
-/* Indirect MDIO clause 22/45 access */
-static int mt753x_mii_rw(struct gsw_mt753x *gsw, int phy, int reg, u16 data,
-			 u32 cmd, u32 st)
-{
-	ktime_t timeout;
-	u32 val, timeout_us;
-	int ret = 0;
-
-	timeout_us = 100000;
-	timeout = ktime_add_us(ktime_get(), timeout_us);
-	while (1) {
-		val = mt753x_reg_read(gsw, PHY_IAC);
-
-		if ((val & PHY_ACS_ST) == 0)
-			break;
-
-		if (ktime_compare(ktime_get(), timeout) > 0)
-			return -ETIMEDOUT;
-	}
-
-	val = (st << MDIO_ST_S) |
-	      ((cmd << MDIO_CMD_S) & MDIO_CMD_M) |
-	      ((phy << MDIO_PHY_ADDR_S) & MDIO_PHY_ADDR_M) |
-	      ((reg << MDIO_REG_ADDR_S) & MDIO_REG_ADDR_M);
-
-	if (cmd == MDIO_CMD_WRITE || cmd == MDIO_CMD_ADDR)
-		val |= data & MDIO_RW_DATA_M;
-
-	mt753x_reg_write(gsw, PHY_IAC, val | PHY_ACS_ST);
-
-	timeout_us = 100000;
-	timeout = ktime_add_us(ktime_get(), timeout_us);
-	while (1) {
-		val = mt753x_reg_read(gsw, PHY_IAC);
-
-		if ((val & PHY_ACS_ST) == 0)
-			break;
-
-		if (ktime_compare(ktime_get(), timeout) > 0)
-			return -ETIMEDOUT;
-	}
-
-	if (cmd == MDIO_CMD_READ || cmd == MDIO_CMD_READ_C45) {
-		val = mt753x_reg_read(gsw, PHY_IAC);
-		ret = val & MDIO_RW_DATA_M;
-	}
-
-	return ret;
-}
-
-int mt753x_mii_read(struct gsw_mt753x *gsw, int phy, int reg)
-{
-	int val;
-
-	if (phy < MT753X_NUM_PHYS)
-		phy = (gsw->phy_base + phy) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->mii_lock);
-	val = mt753x_mii_rw(gsw, phy, reg, 0, MDIO_CMD_READ, MDIO_ST_C22);
-	mutex_unlock(&gsw->mii_lock);
-
-	return val;
-}
-
-void mt753x_mii_write(struct gsw_mt753x *gsw, int phy, int reg, u16 val)
-{
-	if (phy < MT753X_NUM_PHYS)
-		phy = (gsw->phy_base + phy) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->mii_lock);
-	mt753x_mii_rw(gsw, phy, reg, val, MDIO_CMD_WRITE, MDIO_ST_C22);
-	mutex_unlock(&gsw->mii_lock);
-}
-
-int mt753x_mmd_read(struct gsw_mt753x *gsw, int addr, int devad, u16 reg)
-{
-	int val;
-
-	if (addr < MT753X_NUM_PHYS)
-		addr = (gsw->phy_base + addr) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->mii_lock);
-	mt753x_mii_rw(gsw, addr, devad, reg, MDIO_CMD_ADDR, MDIO_ST_C45);
-	val = mt753x_mii_rw(gsw, addr, devad, 0, MDIO_CMD_READ_C45,
-			    MDIO_ST_C45);
-	mutex_unlock(&gsw->mii_lock);
-
-	return val;
-}
-
-void mt753x_mmd_write(struct gsw_mt753x *gsw, int addr, int devad, u16 reg,
-		      u16 val)
-{
-	if (addr < MT753X_NUM_PHYS)
-		addr = (gsw->phy_base + addr) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->mii_lock);
-	mt753x_mii_rw(gsw, addr, devad, reg, MDIO_CMD_ADDR, MDIO_ST_C45);
-	mt753x_mii_rw(gsw, addr, devad, val, MDIO_CMD_WRITE, MDIO_ST_C45);
-	mutex_unlock(&gsw->mii_lock);
-}
-
-int mt753x_mmd_ind_read(struct gsw_mt753x *gsw, int addr, int devad, u16 reg)
-{
-	u16 val;
-
-	if (addr < MT753X_NUM_PHYS)
-		addr = (gsw->phy_base + addr) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->mii_lock);
-
-	mt753x_mii_rw(gsw, addr, MII_MMD_ACC_CTL_REG,
-		      (MMD_ADDR << MMD_CMD_S) |
-		      ((devad << MMD_DEVAD_S) & MMD_DEVAD_M),
-		      MDIO_CMD_WRITE, MDIO_ST_C22);
-
-	mt753x_mii_rw(gsw, addr, MII_MMD_ADDR_DATA_REG, reg,
-		      MDIO_CMD_WRITE, MDIO_ST_C22);
-
-	mt753x_mii_rw(gsw, addr, MII_MMD_ACC_CTL_REG,
-		      (MMD_DATA << MMD_CMD_S) |
-		      ((devad << MMD_DEVAD_S) & MMD_DEVAD_M),
-		      MDIO_CMD_WRITE, MDIO_ST_C22);
-
-	val = mt753x_mii_rw(gsw, addr, MII_MMD_ADDR_DATA_REG, 0,
-			    MDIO_CMD_READ, MDIO_ST_C22);
-
-	mutex_unlock(&gsw->mii_lock);
-
-	return val;
-}
-
-void mt753x_mmd_ind_write(struct gsw_mt753x *gsw, int addr, int devad, u16 reg,
-			  u16 val)
-{
-	if (addr < MT753X_NUM_PHYS)
-		addr = (gsw->phy_base + addr) & MT753X_SMI_ADDR_MASK;
-
-	mutex_lock(&gsw->mii_lock);
-
-	mt753x_mii_rw(gsw, addr, MII_MMD_ACC_CTL_REG,
-		      (MMD_ADDR << MMD_CMD_S) |
-		      ((devad << MMD_DEVAD_S) & MMD_DEVAD_M),
-		      MDIO_CMD_WRITE, MDIO_ST_C22);
-
-	mt753x_mii_rw(gsw, addr, MII_MMD_ADDR_DATA_REG, reg,
-		      MDIO_CMD_WRITE, MDIO_ST_C22);
-
-	mt753x_mii_rw(gsw, addr, MII_MMD_ACC_CTL_REG,
-		      (MMD_DATA << MMD_CMD_S) |
-		      ((devad << MMD_DEVAD_S) & MMD_DEVAD_M),
-		      MDIO_CMD_WRITE, MDIO_ST_C22);
-
-	mt753x_mii_rw(gsw, addr, MII_MMD_ADDR_DATA_REG, val,
-		      MDIO_CMD_WRITE, MDIO_ST_C22);
-
-	mutex_unlock(&gsw->mii_lock);
-}
-
-static inline int mt753x_get_duplex(const struct device_node *np)
-{
-	return of_property_read_bool(np, "full-duplex");
-}
-
-static void mt753x_load_port_cfg(struct gsw_mt753x *gsw)
-{
-	struct device_node *port_np;
-	struct device_node *fixed_link_node;
-	struct mt753x_port_cfg *port_cfg;
-	u32 port;
-
-	for_each_child_of_node(gsw->dev->of_node, port_np) {
-		if (!of_device_is_compatible(port_np, "mediatek,mt753x-port"))
-			continue;
-
-		if (!of_device_is_available(port_np))
-			continue;
-
-		if (of_property_read_u32(port_np, "reg", &port))
-			continue;
-
-		switch (port) {
-		case 5:
-			port_cfg = &gsw->port5_cfg;
-			break;
-		case 6:
-			port_cfg = &gsw->port6_cfg;
-			break;
-		default:
-			continue;
-		}
-
-		if (port_cfg->enabled) {
-			dev_info(gsw->dev, "duplicated node for port%d\n",
-				 port_cfg->phy_mode);
-			continue;
-		}
-
-		port_cfg->np = port_np;
-
-		port_cfg->phy_mode = of_get_phy_mode(port_np);
-		if (port_cfg->phy_mode < 0) {
-			dev_info(gsw->dev, "incorrect phy-mode %d\n", port);
-			continue;
-		}
-
-		fixed_link_node = of_get_child_by_name(port_np, "fixed-link");
-		if (fixed_link_node) {
-			u32 speed;
-
-			port_cfg->force_link = 1;
-			port_cfg->duplex = mt753x_get_duplex(fixed_link_node);
-
-			if (of_property_read_u32(fixed_link_node, "speed",
-						 &speed)) {
-				speed = 0;
-				continue;
-			}
-
-			of_node_put(fixed_link_node);
-
-			switch (speed) {
-			case 10:
-				port_cfg->speed = MAC_SPD_10;
-				break;
-			case 100:
-				port_cfg->speed = MAC_SPD_100;
-				break;
-			case 1000:
-				port_cfg->speed = MAC_SPD_1000;
-				break;
-			case 2500:
-				port_cfg->speed = MAC_SPD_2500;
-				break;
-			default:
-				dev_info(gsw->dev, "incorrect speed %d\n",
-					 speed);
-				continue;
-			}
-		}
-
-		port_cfg->enabled = 1;
-	}
-}
-
-static void mt753x_add_gsw(struct gsw_mt753x *gsw)
-{
-	mutex_lock(&mt753x_devs_lock);
-	gsw->id = mt753x_id++;
-	INIT_LIST_HEAD(&gsw->list);
-	list_add_tail(&gsw->list, &mt753x_devs);
-	mutex_unlock(&mt753x_devs_lock);
-}
-
-static void mt753x_remove_gsw(struct gsw_mt753x *gsw)
-{
-	mutex_lock(&mt753x_devs_lock);
-	list_del(&gsw->list);
-	mutex_unlock(&mt753x_devs_lock);
-}
-
-
-struct gsw_mt753x *mt753x_get_gsw(u32 id)
-{
-	struct gsw_mt753x *dev;
-
-	mutex_lock(&mt753x_devs_lock);
-
-	list_for_each_entry(dev, &mt753x_devs, list) {
-		if (dev->id == id)
-			return dev;
-	}
-
-	mutex_unlock(&mt753x_devs_lock);
-
-	return NULL;
-}
-
-struct gsw_mt753x *mt753x_get_first_gsw(void)
-{
-	struct gsw_mt753x *dev;
-
-	mutex_lock(&mt753x_devs_lock);
-
-	list_for_each_entry(dev, &mt753x_devs, list)
-		return dev;
-
-	mutex_unlock(&mt753x_devs_lock);
-
-	return NULL;
-}
-
-void mt753x_put_gsw(void)
-{
-	mutex_unlock(&mt753x_devs_lock);
-}
-
-void mt753x_lock_gsw(void)
-{
-	mutex_lock(&mt753x_devs_lock);
-}
-
-static int mt753x_hw_reset(struct gsw_mt753x *gsw)
-{
-	struct device_node *np = gsw->dev->of_node;
-	struct reset_control *rstc;
-	int mcm;
-	int ret = -EINVAL;
-
-	mcm = of_property_read_bool(np, "mediatek,mcm");
-	if (mcm) {
-		rstc = devm_reset_control_get(gsw->dev, "mcm");
-		ret = IS_ERR(rstc);
-		if (IS_ERR(rstc)) {
-			dev_err(gsw->dev, "Missing reset ctrl of switch\n");
-			return ret;
-		}
-
-		reset_control_assert(rstc);
-		msleep(30);
-		reset_control_deassert(rstc);
-
-		gsw->reset_pin = -1;
-		return 0;
-	}
-
-	gsw->reset_pin = of_get_named_gpio(np, "reset-gpios", 0);
-	if (gsw->reset_pin < 0) {
-		dev_err(gsw->dev, "Missing reset pin of switch\n");
-		return ret;
-	}
-
-	ret = devm_gpio_request(gsw->dev, gsw->reset_pin, "mt753x-reset");
-	if (ret) {
-		dev_info(gsw->dev, "Failed to request gpio %d\n",
-			 gsw->reset_pin);
-		return ret;
-	}
-
-	gpio_direction_output(gsw->reset_pin, 0);
-	msleep(30);
-	gpio_set_value(gsw->reset_pin, 1);
-	msleep(500);
-
-	return 0;
-}
-
-static irqreturn_t mt753x_irq_handler(int irq, void *dev)
-{
-	struct gsw_mt753x *gsw = dev;
-
-	disable_irq_nosync(gsw->irq);
-
-	schedule_work(&gsw->irq_worker);
-
-	return IRQ_HANDLED;
-}
-
-static int mt753x_probe(struct platform_device *pdev)
-{
-	struct gsw_mt753x *gsw;
-	struct mt753x_sw_id *sw;
-	struct device_node *np = pdev->dev.of_node;
-	struct device_node *mdio;
-	struct mii_bus *mdio_bus;
-	int ret = -EINVAL;
-	struct chip_rev rev;
-	struct mt753x_mapping *map;
-	int i;
-
-	mdio = of_parse_phandle(np, "mediatek,mdio", 0);
-	if (!mdio)
-		return -EINVAL;
-
-	mdio_bus = of_mdio_find_bus(mdio);
-	if (!mdio_bus)
-		return -EPROBE_DEFER;
-
-	gsw = devm_kzalloc(&pdev->dev, sizeof(struct gsw_mt753x), GFP_KERNEL);
-	if (!gsw)
-		return -ENOMEM;
-
-	gsw->host_bus = mdio_bus;
-	gsw->dev = &pdev->dev;
-	mutex_init(&gsw->mii_lock);
-
-	/* Switch hard reset */
-	if (mt753x_hw_reset(gsw))
-		goto fail;
-
-	/* Fetch the SMI address dirst */
-	if (of_property_read_u32(np, "mediatek,smi-addr", &gsw->smi_addr))
-		gsw->smi_addr = MT753X_DFL_SMI_ADDR;
-
-	/* Get LAN/WAN port mapping */
-	map = mt753x_find_mapping(np);
-	if (map) {
-		mt753x_apply_mapping(gsw, map);
-		gsw->global_vlan_enable = 1;
-		dev_info(gsw->dev, "LAN/WAN VLAN setting=%s\n", map->name);
-	}
-
-	/* Load MAC port configurations */
-	mt753x_load_port_cfg(gsw);
-
-	/* Check for valid switch and then initialize */
-	for (i = 0; i < ARRAY_SIZE(mt753x_sw_ids); i++) {
-		if (!mt753x_sw_ids[i]->detect(gsw, &rev)) {
-			sw = mt753x_sw_ids[i];
-
-			gsw->name = rev.name;
-			gsw->model = sw->model;
-
-			dev_info(gsw->dev, "Switch is MediaTek %s rev %d",
-				 gsw->name, rev.rev);
-
-			/* Initialize the switch */
-			ret = sw->init(gsw);
-			if (ret)
-				goto fail;
-
-			break;
-		}
-	}
-
-	if (i >= ARRAY_SIZE(mt753x_sw_ids)) {
-		dev_err(gsw->dev, "No mt753x switch found\n");
-		goto fail;
-	}
-
-	gsw->irq = platform_get_irq(pdev, 0);
-	if (gsw->irq >= 0) {
-		ret = devm_request_irq(gsw->dev, gsw->irq, mt753x_irq_handler,
-				       0, dev_name(gsw->dev), gsw);
-		if (ret) {
-			dev_err(gsw->dev, "Failed to request irq %d\n",
-				gsw->irq);
-			goto fail;
-		}
-
-		INIT_WORK(&gsw->irq_worker, mt753x_irq_worker);
-	}
-
-	platform_set_drvdata(pdev, gsw);
-
-	gsw->phy_status_poll = of_property_read_bool(gsw->dev->of_node,
-						     "mediatek,phy-poll");
-
-	mt753x_add_gsw(gsw);
-
-	mt753x_swconfig_init(gsw);
-
-	if (sw->post_init)
-		sw->post_init(gsw);
-
-	if (gsw->irq >= 0)
-		mt753x_irq_enable(gsw);
-
-	return 0;
-
-fail:
-	devm_kfree(&pdev->dev, gsw);
-
-	return ret;
-}
-
-static int mt753x_remove(struct platform_device *pdev)
-{
-	struct gsw_mt753x *gsw = platform_get_drvdata(pdev);
-
-	if (gsw->irq >= 0)
-		cancel_work_sync(&gsw->irq_worker);
-
-	if (gsw->reset_pin >= 0)
-		devm_gpio_free(&pdev->dev, gsw->reset_pin);
-
-#ifdef CONFIG_SWCONFIG
-	mt753x_swconfig_destroy(gsw);
-#endif
-
-	mt753x_remove_gsw(gsw);
-
-	platform_set_drvdata(pdev, NULL);
-
-	return 0;
-}
-
-static const struct of_device_id mt753x_ids[] = {
-	{ .compatible = "mediatek,mt753x" },
-	{ },
-};
-
-MODULE_DEVICE_TABLE(of, mt753x_ids);
-
-static struct platform_driver mt753x_driver = {
-	.probe = mt753x_probe,
-	.remove = mt753x_remove,
-	.driver = {
-		.name = "mt753x",
-		.of_match_table = mt753x_ids,
-	},
-};
-
-static int __init mt753x_init(void)
-{
-	int ret;
-
-	INIT_LIST_HEAD(&mt753x_devs);
-	ret = platform_driver_register(&mt753x_driver);
-
-	mt753x_nl_init();
-
-	return ret;
-}
-module_init(mt753x_init);
-
-static void __exit mt753x_exit(void)
-{
-	mt753x_nl_exit();
-
-	platform_driver_unregister(&mt753x_driver);
-}
-module_exit(mt753x_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Weijie Gao <weijie.gao@mediatek.com>");
-MODULE_DESCRIPTION("Driver for MediaTek MT753x Gigabit Switch");
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_nl.c b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_nl.c
deleted file mode 100644
index ccde2c9209..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_nl.c
+++ /dev/null
@@ -1,382 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Sirui Zhao <Sirui.Zhao@mediatek.com>
- */
-
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <net/genetlink.h>
-
-#include "mt753x.h"
-#include "mt753x_nl.h"
-
-struct mt753x_nl_cmd_item {
-	enum mt753x_cmd cmd;
-	bool require_dev;
-	int (*process)(struct genl_info *info, struct gsw_mt753x *gsw);
-	u32 nr_required_attrs;
-	const enum mt753x_attr *required_attrs;
-};
-
-static int mt753x_nl_response(struct sk_buff *skb, struct genl_info *info);
-
-/*
-static const struct nla_policy mt753x_nl_cmd_policy[] = {
-	[MT753X_ATTR_TYPE_MESG] = { .type = NLA_STRING },
-	[MT753X_ATTR_TYPE_PHY] = { .type = NLA_S32 },
-	[MT753X_ATTR_TYPE_REG] = { .type = NLA_S32 },
-	[MT753X_ATTR_TYPE_VAL] = { .type = NLA_S32 },
-	[MT753X_ATTR_TYPE_DEV_NAME] = { .type = NLA_S32 },
-	[MT753X_ATTR_TYPE_DEV_ID] = { .type = NLA_S32 },
-	[MT753X_ATTR_TYPE_DEVAD] = { .type = NLA_S32 },
-};
-*/
-
-static const struct genl_ops mt753x_nl_ops[] = {
-	{
-		.cmd = MT753X_CMD_REQUEST,
-		.doit = mt753x_nl_response,
-//		.policy = mt753x_nl_cmd_policy,
-		.flags = GENL_ADMIN_PERM,
-	}, {
-		.cmd = MT753X_CMD_READ,
-		.doit = mt753x_nl_response,
-//		.policy = mt753x_nl_cmd_policy,
-		.flags = GENL_ADMIN_PERM,
-	}, {
-		.cmd = MT753X_CMD_WRITE,
-		.doit = mt753x_nl_response,
-//		.policy = mt753x_nl_cmd_policy,
-		.flags = GENL_ADMIN_PERM,
-	},
-};
-
-static struct genl_family mt753x_nl_family = {
-	.name =		MT753X_GENL_NAME,
-	.version =	MT753X_GENL_VERSION,
-	.maxattr =	MT753X_NR_ATTR_TYPE,
-	.ops =		mt753x_nl_ops,
-	.n_ops =	ARRAY_SIZE(mt753x_nl_ops),
-};
-
-static int mt753x_nl_list_devs(char *buff, int size)
-{
-	struct gsw_mt753x *gsw;
-	int len, total = 0;
-	char buf[80];
-
-	memset(buff, 0, size);
-
-	mt753x_lock_gsw();
-
-	list_for_each_entry(gsw, &mt753x_devs, list) {
-		len = snprintf(buf, sizeof(buf),
-			       "id: %d, model: %s, node: %s\n",
-			       gsw->id, gsw->name, gsw->dev->of_node->name);
-		strncat(buff, buf, size - total);
-		total += len;
-	}
-
-	mt753x_put_gsw();
-
-	return total;
-}
-
-static int mt753x_nl_prepare_reply(struct genl_info *info, u8 cmd,
-				   struct sk_buff **skbp)
-{
-	struct sk_buff *msg;
-	void *reply;
-
-	if (!info)
-		return -EINVAL;
-
-	msg = genlmsg_new(NLMSG_GOODSIZE, GFP_KERNEL);
-	if (!msg)
-		return -ENOMEM;
-
-	/* Construct send-back message header */
-	reply = genlmsg_put(msg, info->snd_portid, info->snd_seq,
-			    &mt753x_nl_family, 0, cmd);
-	if (!reply) {
-		nlmsg_free(msg);
-		return -EINVAL;
-	}
-
-	*skbp = msg;
-	return 0;
-}
-
-static int mt753x_nl_send_reply(struct sk_buff *skb, struct genl_info *info)
-{
-	struct genlmsghdr *genlhdr = nlmsg_data(nlmsg_hdr(skb));
-	void *reply = genlmsg_data(genlhdr);
-
-	/* Finalize a generic netlink message (update message header) */
-	genlmsg_end(skb, reply);
-
-	/* reply to a request */
-	return genlmsg_reply(skb, info);
-}
-
-static s32 mt753x_nl_get_s32(struct genl_info *info, enum mt753x_attr attr,
-			     s32 defval)
-{
-	struct nlattr *na;
-
-	na = info->attrs[attr];
-	if (na)
-		return nla_get_s32(na);
-
-	return defval;
-}
-
-static int mt753x_nl_get_u32(struct genl_info *info, enum mt753x_attr attr,
-			     u32 *val)
-{
-	struct nlattr *na;
-
-	na = info->attrs[attr];
-	if (na) {
-		*val = nla_get_u32(na);
-		return 0;
-	}
-
-	return -1;
-}
-
-static struct gsw_mt753x *mt753x_nl_parse_find_gsw(struct genl_info *info)
-{
-	struct gsw_mt753x *gsw;
-	struct nlattr *na;
-	int gsw_id;
-
-	na = info->attrs[MT753X_ATTR_TYPE_DEV_ID];
-	if (na) {
-		gsw_id = nla_get_s32(na);
-		if (gsw_id >= 0)
-			gsw = mt753x_get_gsw(gsw_id);
-		else
-			gsw = mt753x_get_first_gsw();
-	} else {
-		gsw = mt753x_get_first_gsw();
-	}
-
-	return gsw;
-}
-
-static int mt753x_nl_get_swdevs(struct genl_info *info, struct gsw_mt753x *gsw)
-{
-	struct sk_buff *rep_skb = NULL;
-	char dev_info[512];
-	int ret;
-
-	ret = mt753x_nl_list_devs(dev_info, sizeof(dev_info));
-	if (!ret) {
-		pr_info("No switch registered\n");
-		return -EINVAL;
-	}
-
-	ret = mt753x_nl_prepare_reply(info, MT753X_CMD_REPLY, &rep_skb);
-	if (ret < 0)
-		goto err;
-
-	ret = nla_put_string(rep_skb, MT753X_ATTR_TYPE_MESG, dev_info);
-	if (ret < 0)
-		goto err;
-
-	return mt753x_nl_send_reply(rep_skb, info);
-
-err:
-	if (rep_skb)
-		nlmsg_free(rep_skb);
-
-	return ret;
-}
-
-static int mt753x_nl_reply_read(struct genl_info *info, struct gsw_mt753x *gsw)
-{
-	struct sk_buff *rep_skb = NULL;
-	s32 phy, devad, reg;
-	int value;
-	int ret = 0;
-
-	phy = mt753x_nl_get_s32(info, MT753X_ATTR_TYPE_PHY, -1);
-	devad = mt753x_nl_get_s32(info, MT753X_ATTR_TYPE_DEVAD, -1);
-	reg = mt753x_nl_get_s32(info, MT753X_ATTR_TYPE_REG, -1);
-
-	if (reg < 0)
-		goto err;
-
-	ret = mt753x_nl_prepare_reply(info, MT753X_CMD_READ, &rep_skb);
-	if (ret < 0)
-		goto err;
-
-	if (phy >= 0) {
-		if (devad < 0)
-			value = gsw->mii_read(gsw, phy, reg);
-		else
-			value = gsw->mmd_read(gsw, phy, devad, reg);
-	} else {
-		value = mt753x_reg_read(gsw, reg);
-	}
-
-	ret = nla_put_s32(rep_skb, MT753X_ATTR_TYPE_REG, reg);
-	if (ret < 0)
-		goto err;
-
-	ret = nla_put_s32(rep_skb, MT753X_ATTR_TYPE_VAL, value);
-	if (ret < 0)
-		goto err;
-
-	return mt753x_nl_send_reply(rep_skb, info);
-
-err:
-	if (rep_skb)
-		nlmsg_free(rep_skb);
-
-	return ret;
-}
-
-static int mt753x_nl_reply_write(struct genl_info *info, struct gsw_mt753x *gsw)
-{
-	struct sk_buff *rep_skb = NULL;
-	s32 phy, devad, reg;
-	u32 value;
-	int ret = 0;
-
-	phy = mt753x_nl_get_s32(info, MT753X_ATTR_TYPE_PHY, -1);
-	devad = mt753x_nl_get_s32(info, MT753X_ATTR_TYPE_DEVAD, -1);
-	reg = mt753x_nl_get_s32(info, MT753X_ATTR_TYPE_REG, -1);
-
-	if (mt753x_nl_get_u32(info, MT753X_ATTR_TYPE_VAL, &value))
-		goto err;
-
-	if (reg < 0)
-		goto err;
-
-	ret = mt753x_nl_prepare_reply(info, MT753X_CMD_WRITE, &rep_skb);
-	if (ret < 0)
-		goto err;
-
-	if (phy >= 0) {
-		if (devad < 0)
-			gsw->mii_write(gsw, phy, reg, value);
-		else
-			gsw->mmd_write(gsw, phy, devad, reg, value);
-	} else {
-		mt753x_reg_write(gsw, reg, value);
-	}
-
-	ret = nla_put_s32(rep_skb, MT753X_ATTR_TYPE_REG, reg);
-	if (ret < 0)
-		goto err;
-
-	ret = nla_put_s32(rep_skb, MT753X_ATTR_TYPE_VAL, value);
-	if (ret < 0)
-		goto err;
-
-	return mt753x_nl_send_reply(rep_skb, info);
-
-err:
-	if (rep_skb)
-		nlmsg_free(rep_skb);
-
-	return ret;
-}
-
-static const enum mt753x_attr mt753x_nl_cmd_read_attrs[] = {
-	MT753X_ATTR_TYPE_REG
-};
-
-static const enum mt753x_attr mt753x_nl_cmd_write_attrs[] = {
-	MT753X_ATTR_TYPE_REG,
-	MT753X_ATTR_TYPE_VAL
-};
-
-static const struct mt753x_nl_cmd_item mt753x_nl_cmds[] = {
-	{
-		.cmd = MT753X_CMD_REQUEST,
-		.require_dev = false,
-		.process = mt753x_nl_get_swdevs
-	}, {
-		.cmd = MT753X_CMD_READ,
-		.require_dev = true,
-		.process = mt753x_nl_reply_read,
-		.required_attrs = mt753x_nl_cmd_read_attrs,
-		.nr_required_attrs = ARRAY_SIZE(mt753x_nl_cmd_read_attrs),
-	}, {
-		.cmd = MT753X_CMD_WRITE,
-		.require_dev = true,
-		.process = mt753x_nl_reply_write,
-		.required_attrs = mt753x_nl_cmd_write_attrs,
-		.nr_required_attrs = ARRAY_SIZE(mt753x_nl_cmd_write_attrs),
-	}
-};
-
-static int mt753x_nl_response(struct sk_buff *skb, struct genl_info *info)
-{
-	struct genlmsghdr *hdr = nlmsg_data(info->nlhdr);
-	const struct mt753x_nl_cmd_item *cmditem = NULL;
-	struct gsw_mt753x *gsw = NULL;
-	u32 sat_req_attrs = 0;
-	int i, ret;
-
-	for (i = 0; i < ARRAY_SIZE(mt753x_nl_cmds); i++) {
-		if (hdr->cmd == mt753x_nl_cmds[i].cmd) {
-			cmditem = &mt753x_nl_cmds[i];
-			break;
-		}
-	}
-
-	if (!cmditem) {
-		pr_info("mt753x-nl: unknown cmd %u\n", hdr->cmd);
-		return -EINVAL;
-	}
-
-	for (i = 0; i < cmditem->nr_required_attrs; i++) {
-		if (info->attrs[cmditem->required_attrs[i]])
-			sat_req_attrs++;
-	}
-
-	if (sat_req_attrs != cmditem->nr_required_attrs) {
-		pr_info("mt753x-nl: missing required attr(s) for cmd %u\n",
-			hdr->cmd);
-		return -EINVAL;
-	}
-
-	if (cmditem->require_dev) {
-		gsw = mt753x_nl_parse_find_gsw(info);
-		if (!gsw) {
-			pr_info("mt753x-nl: failed to find switch dev\n");
-			return -EINVAL;
-		}
-	}
-
-	ret = cmditem->process(info, gsw);
-
-	mt753x_put_gsw();
-
-	return ret;
-}
-
-int __init mt753x_nl_init(void)
-{
-	int ret;
-
-	ret = genl_register_family(&mt753x_nl_family);
-	if (ret) {
-		pr_info("mt753x-nl: genl_register_family_with_ops failed\n");
-		return ret;
-	}
-
-	return 0;
-}
-
-void __exit mt753x_nl_exit(void)
-{
-	genl_unregister_family(&mt753x_nl_family);
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_nl.h b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_nl.h
deleted file mode 100644
index 85dc9e791a..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_nl.h
+++ /dev/null
@@ -1,43 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Sirui Zhao <Sirui.Zhao@mediatek.com>
- */
-
-#ifndef _MT753X_NL_H_
-#define _MT753X_NL_H_
-
-#define MT753X_GENL_NAME		"mt753x"
-#define MT753X_GENL_VERSION		0x1
-
-enum mt753x_cmd {
-	MT753X_CMD_UNSPEC = 0,
-	MT753X_CMD_REQUEST,
-	MT753X_CMD_REPLY,
-	MT753X_CMD_READ,
-	MT753X_CMD_WRITE,
-
-	__MT753X_CMD_MAX,
-};
-
-enum mt753x_attr {
-	MT753X_ATTR_TYPE_UNSPEC = 0,
-	MT753X_ATTR_TYPE_MESG,
-	MT753X_ATTR_TYPE_PHY,
-	MT753X_ATTR_TYPE_DEVAD,
-	MT753X_ATTR_TYPE_REG,
-	MT753X_ATTR_TYPE_VAL,
-	MT753X_ATTR_TYPE_DEV_NAME,
-	MT753X_ATTR_TYPE_DEV_ID,
-
-	__MT753X_ATTR_TYPE_MAX,
-};
-
-#define MT753X_NR_ATTR_TYPE		(__MT753X_ATTR_TYPE_MAX - 1)
-
-#ifdef __KERNEL__
-int __init mt753x_nl_init(void);
-void __exit mt753x_nl_exit(void);
-#endif /* __KERNEL__ */
-
-#endif /* _MT753X_NL_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_regs.h b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_regs.h
deleted file mode 100644
index 3f23ae200e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_regs.h
+++ /dev/null
@@ -1,294 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-#ifndef _MT753X_REGS_H_
-#define _MT753X_REGS_H_
-
-#include <linux/bitops.h>
-
-/* Values of Egress TAG Control */
-#define ETAG_CTRL_UNTAG			0
-#define ETAG_CTRL_TAG			2
-#define ETAG_CTRL_SWAP			1
-#define ETAG_CTRL_STACK			3
-
-#define VTCR				0x90
-#define VAWD1				0x94
-#define VAWD2				0x98
-
-/* Fields of VTCR */
-#define VTCR_BUSY			BIT(31)
-#define IDX_INVLD			BIT(16)
-#define VTCR_FUNC_S			12
-#define VTCR_FUNC_M			0xf000
-#define VTCR_VID_S			0
-#define VTCR_VID_M			0xfff
-
-/* Values of VTCR_FUNC */
-#define VTCR_READ_VLAN_ENTRY		0
-#define VTCR_WRITE_VLAN_ENTRY		1
-#define VTCR_INVD_VLAN_ENTRY		2
-#define VTCR_ENABLE_VLAN_ENTRY		3
-#define VTCR_READ_ACL_ENTRY		4
-#define VTCR_WRITE_ACL_ENTRY		5
-#define VTCR_READ_TRTCM_TABLE		6
-#define VTCR_WRITE_TRTCM_TABLE		7
-#define VTCR_READ_ACL_MASK_ENTRY	8
-#define VTCR_WRITE_ACL_MASK_ENTRY	9
-#define VTCR_READ_ACL_RULE_ENTRY	10
-#define VTCR_WRITE_ACL_RULE_ENTRY	11
-#define VTCR_READ_ACL_RATE_ENTRY	12
-#define VTCR_WRITE_ACL_RATE_ENTRY	13
-
-/* VLAN entry fields */
-/* VAWD1 */
-#define PORT_STAG			BIT(31)
-#define IVL_MAC				BIT(30)
-#define EG_CON				BIT(29)
-#define VTAG_EN				BIT(28)
-#define COPY_PRI			BIT(27)
-#define USER_PRI_S			24
-#define USER_PRI_M			0x7000000
-#define PORT_MEM_S			16
-#define PORT_MEM_M			0xff0000
-#define S_TAG1_S			4
-#define S_TAG1_M			0xfff0
-#define FID_S				1
-#define FID_M				0x0e
-#define VENTRY_VALID			BIT(0)
-
-/* VAWD2 */
-#define S_TAG2_S			16
-#define S_TAG2_M			0xffff0000
-#define PORT_ETAG_S(p)			((p) * 2)
-#define PORT_ETAG_M			0x03
-
-#define PORT_CTRL_BASE			0x2000
-#define PORT_CTRL_PORT_OFFSET		0x100
-#define PORT_CTRL_REG(p, r)		(PORT_CTRL_BASE + \
-					(p) * PORT_CTRL_PORT_OFFSET +  (r))
-#define CKGCR(p)			PORT_CTRL_REG(p, 0x00)
-#define PCR(p)				PORT_CTRL_REG(p, 0x04)
-#define PIC(p)				PORT_CTRL_REG(p, 0x08)
-#define PSC(p)				PORT_CTRL_REG(p, 0x0c)
-#define PVC(p)				PORT_CTRL_REG(p, 0x10)
-#define PPBV1(p)			PORT_CTRL_REG(p, 0x14)
-#define PPBV2(p)			PORT_CTRL_REG(p, 0x18)
-#define BSR(p)				PORT_CTRL_REG(p, 0x1c)
-#define STAG01				PORT_CTRL_REG(p, 0x20)
-#define STAG23				PORT_CTRL_REG(p, 0x24)
-#define STAG45				PORT_CTRL_REG(p, 0x28)
-#define STAG67				PORT_CTRL_REG(p, 0x2c)
-
-#define PPBV(p, g)			(PPBV1(p) + ((g) / 2) * 4)
-
-/* Fields of PCR */
-#define MLDV2_EN			BIT(30)
-#define EG_TAG_S			28
-#define EG_TAG_M			0x30000000
-#define PORT_PRI_S			24
-#define PORT_PRI_M			0x7000000
-#define PORT_MATRIX_S			16
-#define PORT_MATRIX_M			0xff0000
-#define UP2DSCP_EN			BIT(12)
-#define UP2TAG_EN			BIT(11)
-#define ACL_EN				BIT(10)
-#define PORT_TX_MIR			BIT(9)
-#define PORT_RX_MIR			BIT(8)
-#define ACL_MIR				BIT(7)
-#define MIS_PORT_FW_S			4
-#define MIS_PORT_FW_M			0x70
-#define VLAN_MIS			BIT(2)
-#define PORT_VLAN_S			0
-#define PORT_VLAN_M			0x03
-
-/* Values of PORT_VLAN */
-#define PORT_MATRIX_MODE		0
-#define FALLBACK_MODE			1
-#define CHECK_MODE			2
-#define SECURITY_MODE			3
-
-/* Fields of PVC */
-#define STAG_VPID_S			16
-#define STAG_VPID_M			0xffff0000
-#define DIS_PVID			BIT(15)
-#define FORCE_PVID			BIT(14)
-#define PT_VPM				BIT(12)
-#define PT_OPTION			BIT(11)
-#define PVC_EG_TAG_S			8
-#define PVC_EG_TAG_M			0x700
-#define VLAN_ATTR_S			6
-#define VLAN_ATTR_M			0xc0
-#define PVC_PORT_STAG			BIT(5)
-#define BC_LKYV_EN			BIT(4)
-#define MC_LKYV_EN			BIT(3)
-#define UC_LKYV_EN			BIT(2)
-#define ACC_FRM_S			0
-#define ACC_FRM_M			0x03
-
-/* Values of VLAN_ATTR */
-#define VA_USER_PORT			0
-#define VA_STACK_PORT			1
-#define VA_TRANSLATION_PORT		2
-#define VA_TRANSPARENT_PORT		3
-
-/* Fields of PPBV */
-#define GRP_PORT_PRI_S(g)		(((g) % 2) * 16 + 13)
-#define GRP_PORT_PRI_M			0x07
-#define GRP_PORT_VID_S(g)		(((g) % 2) * 16)
-#define GRP_PORT_VID_M			0xfff
-
-#define PORT_MAC_CTRL_BASE		0x3000
-#define PORT_MAC_CTRL_PORT_OFFSET	0x100
-#define PORT_MAC_CTRL_REG(p, r)		(PORT_MAC_CTRL_BASE + \
-					(p) * PORT_MAC_CTRL_PORT_OFFSET + (r))
-#define PMCR(p)				PORT_MAC_CTRL_REG(p, 0x00)
-#define PMEEECR(p)			PORT_MAC_CTRL_REG(p, 0x04)
-#define PMSR(p)				PORT_MAC_CTRL_REG(p, 0x08)
-#define PINT_EN(p)			PORT_MAC_CTRL_REG(p, 0x10)
-#define PINT_STS(p)			PORT_MAC_CTRL_REG(p, 0x14)
-
-#define GMACCR				(PORT_MAC_CTRL_BASE + 0xe0)
-#define TXCRC_EN			BIT(19)
-#define RXCRC_EN			BIT(18)
-#define PRMBL_LMT_EN			BIT(17)
-#define MTCC_LMT_S			9
-#define MTCC_LMT_M			0x1e00
-#define MAX_RX_JUMBO_S			2
-#define MAX_RX_JUMBO_M			0x3c
-#define MAX_RX_PKT_LEN_S		0
-#define MAX_RX_PKT_LEN_M		0x3
-
-/* Values of MAX_RX_PKT_LEN */
-#define RX_PKT_LEN_1518			0
-#define RX_PKT_LEN_1536			1
-#define RX_PKT_LEN_1522			2
-#define RX_PKT_LEN_MAX_JUMBO		3
-
-/* Fields of PMCR */
-#define IPG_CFG_S			18
-#define IPG_CFG_M			0xc0000
-#define EXT_PHY				BIT(17)
-#define MAC_MODE			BIT(16)
-#define MAC_TX_EN			BIT(14)
-#define MAC_RX_EN			BIT(13)
-#define MAC_PRE				BIT(11)
-#define BKOFF_EN			BIT(9)
-#define BACKPR_EN			BIT(8)
-#define FORCE_EEE1G			BIT(7)
-#define FORCE_EEE1000			BIT(6)
-#define FORCE_RX_FC			BIT(5)
-#define FORCE_TX_FC			BIT(4)
-#define FORCE_SPD_S			2
-#define FORCE_SPD_M			0x0c
-#define FORCE_DPX			BIT(1)
-#define FORCE_LINK			BIT(0)
-
-/* Fields of PMSR */
-#define EEE1G_STS			BIT(7)
-#define EEE100_STS			BIT(6)
-#define RX_FC_STS			BIT(5)
-#define TX_FC_STS			BIT(4)
-#define MAC_SPD_STS_S			2
-#define MAC_SPD_STS_M			0x0c
-#define MAC_DPX_STS			BIT(1)
-#define MAC_LNK_STS			BIT(0)
-
-/* Values of MAC_SPD_STS */
-#define MAC_SPD_10			0
-#define MAC_SPD_100			1
-#define MAC_SPD_1000			2
-#define MAC_SPD_2500			3
-
-/* Values of IPG_CFG */
-#define IPG_96BIT			0
-#define IPG_96BIT_WITH_SHORT_IPG	1
-#define IPG_64BIT			2
-
-#define MIB_COUNTER_BASE		0x4000
-#define MIB_COUNTER_PORT_OFFSET		0x100
-#define MIB_COUNTER_REG(p, r)		(MIB_COUNTER_BASE + \
-					(p) * MIB_COUNTER_PORT_OFFSET + (r))
-#define STATS_TDPC			0x00
-#define STATS_TCRC			0x04
-#define STATS_TUPC			0x08
-#define STATS_TMPC			0x0C
-#define STATS_TBPC			0x10
-#define STATS_TCEC			0x14
-#define STATS_TSCEC			0x18
-#define STATS_TMCEC			0x1C
-#define STATS_TDEC			0x20
-#define STATS_TLCEC			0x24
-#define STATS_TXCEC			0x28
-#define STATS_TPPC			0x2C
-#define STATS_TL64PC			0x30
-#define STATS_TL65PC			0x34
-#define STATS_TL128PC			0x38
-#define STATS_TL256PC			0x3C
-#define STATS_TL512PC			0x40
-#define STATS_TL1024PC			0x44
-#define STATS_TOC			0x48
-#define STATS_RDPC			0x60
-#define STATS_RFPC			0x64
-#define STATS_RUPC			0x68
-#define STATS_RMPC			0x6C
-#define STATS_RBPC			0x70
-#define STATS_RAEPC			0x74
-#define STATS_RCEPC			0x78
-#define STATS_RUSPC			0x7C
-#define STATS_RFEPC			0x80
-#define STATS_ROSPC			0x84
-#define STATS_RJEPC			0x88
-#define STATS_RPPC			0x8C
-#define STATS_RL64PC			0x90
-#define STATS_RL65PC			0x94
-#define STATS_RL128PC			0x98
-#define STATS_RL256PC			0x9C
-#define STATS_RL512PC			0xA0
-#define STATS_RL1024PC			0xA4
-#define STATS_ROC			0xA8
-#define STATS_RDPC_CTRL			0xB0
-#define STATS_RDPC_ING			0xB4
-#define STATS_RDPC_ARL			0xB8
-
-#define SYS_CTRL			0x7000
-#define SW_PHY_RST			BIT(2)
-#define SW_SYS_RST			BIT(1)
-#define SW_REG_RST			BIT(0)
-
-#define SYS_INT_EN			0x7008
-#define SYS_INT_STS			0x700c
-#define MAC_PC_INT			BIT(16)
-#define PHY_INT(p)			BIT((p) + 8)
-#define PHY_LC_INT(p)			BIT(p)
-
-#define PHY_IAC				0x701c
-#define PHY_ACS_ST			BIT(31)
-#define MDIO_REG_ADDR_S			25
-#define MDIO_REG_ADDR_M			0x3e000000
-#define MDIO_PHY_ADDR_S			20
-#define MDIO_PHY_ADDR_M			0x1f00000
-#define MDIO_CMD_S			18
-#define MDIO_CMD_M			0xc0000
-#define MDIO_ST_S			16
-#define MDIO_ST_M			0x30000
-#define MDIO_RW_DATA_S			0
-#define MDIO_RW_DATA_M			0xffff
-
-/* MDIO_CMD: MDIO commands */
-#define MDIO_CMD_ADDR			0
-#define MDIO_CMD_WRITE			1
-#define MDIO_CMD_READ			2
-#define MDIO_CMD_READ_C45		3
-
-/* MDIO_ST: MDIO start field */
-#define MDIO_ST_C45			0
-#define MDIO_ST_C22			1
-
-#define HWSTRAP				0x7800
-#define MHWSTRAP			0x7804
-
-#endif /* _MT753X_REGS_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_swconfig.c b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_swconfig.c
deleted file mode 100644
index 342ad576b2..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_swconfig.c
+++ /dev/null
@@ -1,510 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-#include <linux/if.h>
-#include <linux/list.h>
-#include <linux/if_ether.h>
-#include <linux/skbuff.h>
-#include <linux/netdevice.h>
-#include <linux/netlink.h>
-#include <linux/bitops.h>
-#include <net/genetlink.h>
-#include <linux/delay.h>
-#include <linux/phy.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/lockdep.h>
-#include <linux/workqueue.h>
-#include <linux/of_device.h>
-
-#include "mt753x.h"
-#include "mt753x_swconfig.h"
-#include "mt753x_regs.h"
-
-#define MT753X_PORT_MIB_TXB_ID	18	/* TxByte */
-#define MT753X_PORT_MIB_RXB_ID	37	/* RxByte */
-
-#define MIB_DESC(_s, _o, _n)   \
-	{                       \
-		.size = (_s),   \
-		.offset = (_o), \
-		.name = (_n),   \
-	}
-
-struct mt753x_mib_desc {
-	unsigned int size;
-	unsigned int offset;
-	const char *name;
-};
-
-static const struct mt753x_mib_desc mt753x_mibs[] = {
-	MIB_DESC(1, STATS_TDPC, "TxDrop"),
-	MIB_DESC(1, STATS_TCRC, "TxCRC"),
-	MIB_DESC(1, STATS_TUPC, "TxUni"),
-	MIB_DESC(1, STATS_TMPC, "TxMulti"),
-	MIB_DESC(1, STATS_TBPC, "TxBroad"),
-	MIB_DESC(1, STATS_TCEC, "TxCollision"),
-	MIB_DESC(1, STATS_TSCEC, "TxSingleCol"),
-	MIB_DESC(1, STATS_TMCEC, "TxMultiCol"),
-	MIB_DESC(1, STATS_TDEC, "TxDefer"),
-	MIB_DESC(1, STATS_TLCEC, "TxLateCol"),
-	MIB_DESC(1, STATS_TXCEC, "TxExcCol"),
-	MIB_DESC(1, STATS_TPPC, "TxPause"),
-	MIB_DESC(1, STATS_TL64PC, "Tx64Byte"),
-	MIB_DESC(1, STATS_TL65PC, "Tx65Byte"),
-	MIB_DESC(1, STATS_TL128PC, "Tx128Byte"),
-	MIB_DESC(1, STATS_TL256PC, "Tx256Byte"),
-	MIB_DESC(1, STATS_TL512PC, "Tx512Byte"),
-	MIB_DESC(1, STATS_TL1024PC, "Tx1024Byte"),
-	MIB_DESC(2, STATS_TOC, "TxByte"),
-	MIB_DESC(1, STATS_RDPC, "RxDrop"),
-	MIB_DESC(1, STATS_RFPC, "RxFiltered"),
-	MIB_DESC(1, STATS_RUPC, "RxUni"),
-	MIB_DESC(1, STATS_RMPC, "RxMulti"),
-	MIB_DESC(1, STATS_RBPC, "RxBroad"),
-	MIB_DESC(1, STATS_RAEPC, "RxAlignErr"),
-	MIB_DESC(1, STATS_RCEPC, "RxCRC"),
-	MIB_DESC(1, STATS_RUSPC, "RxUnderSize"),
-	MIB_DESC(1, STATS_RFEPC, "RxFragment"),
-	MIB_DESC(1, STATS_ROSPC, "RxOverSize"),
-	MIB_DESC(1, STATS_RJEPC, "RxJabber"),
-	MIB_DESC(1, STATS_RPPC, "RxPause"),
-	MIB_DESC(1, STATS_RL64PC, "Rx64Byte"),
-	MIB_DESC(1, STATS_RL65PC, "Rx65Byte"),
-	MIB_DESC(1, STATS_RL128PC, "Rx128Byte"),
-	MIB_DESC(1, STATS_RL256PC, "Rx256Byte"),
-	MIB_DESC(1, STATS_RL512PC, "Rx512Byte"),
-	MIB_DESC(1, STATS_RL1024PC, "Rx1024Byte"),
-	MIB_DESC(2, STATS_ROC, "RxByte"),
-	MIB_DESC(1, STATS_RDPC_CTRL, "RxCtrlDrop"),
-	MIB_DESC(1, STATS_RDPC_ING, "RxIngDrop"),
-	MIB_DESC(1, STATS_RDPC_ARL, "RxARLDrop")
-};
-
-enum {
-	/* Global attributes. */
-	MT753X_ATTR_ENABLE_VLAN,
-};
-
-static int mt753x_get_vlan_enable(struct switch_dev *dev,
-				  const struct switch_attr *attr,
-				  struct switch_val *val)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	val->value.i = gsw->global_vlan_enable;
-
-	return 0;
-}
-
-static int mt753x_set_vlan_enable(struct switch_dev *dev,
-				  const struct switch_attr *attr,
-				  struct switch_val *val)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	gsw->global_vlan_enable = val->value.i != 0;
-
-	return 0;
-}
-
-static int mt753x_get_port_pvid(struct switch_dev *dev, int port, int *val)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	if (port >= MT753X_NUM_PORTS)
-		return -EINVAL;
-
-	*val = mt753x_reg_read(gsw, PPBV1(port));
-	*val &= GRP_PORT_VID_M;
-
-	return 0;
-}
-
-static int mt753x_set_port_pvid(struct switch_dev *dev, int port, int pvid)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	if (port >= MT753X_NUM_PORTS)
-		return -EINVAL;
-
-	if (pvid < MT753X_MIN_VID || pvid > MT753X_MAX_VID)
-		return -EINVAL;
-
-	gsw->port_entries[port].pvid = pvid;
-
-	return 0;
-}
-
-static int mt753x_get_vlan_ports(struct switch_dev *dev, struct switch_val *val)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-	u32 member;
-	u32 etags;
-	int i;
-
-	val->len = 0;
-
-	if (val->port_vlan < 0 || val->port_vlan >= MT753X_NUM_VLANS)
-		return -EINVAL;
-
-	mt753x_vlan_ctrl(gsw, VTCR_READ_VLAN_ENTRY, val->port_vlan);
-
-	member = mt753x_reg_read(gsw, VAWD1);
-	member &= PORT_MEM_M;
-	member >>= PORT_MEM_S;
-
-	etags = mt753x_reg_read(gsw, VAWD2);
-
-	for (i = 0; i < MT753X_NUM_PORTS; i++) {
-		struct switch_port *p;
-		int etag;
-
-		if (!(member & BIT(i)))
-			continue;
-
-		p = &val->value.ports[val->len++];
-		p->id = i;
-
-		etag = (etags >> PORT_ETAG_S(i)) & PORT_ETAG_M;
-
-		if (etag == ETAG_CTRL_TAG)
-			p->flags |= BIT(SWITCH_PORT_FLAG_TAGGED);
-		else if (etag != ETAG_CTRL_UNTAG)
-			dev_info(gsw->dev,
-				 "vlan egress tag control neither untag nor tag.\n");
-	}
-
-	return 0;
-}
-
-static int mt753x_set_vlan_ports(struct switch_dev *dev, struct switch_val *val)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-	u8 member = 0;
-	u8 etags = 0;
-	int i;
-
-	if (val->port_vlan < 0 || val->port_vlan >= MT753X_NUM_VLANS ||
-	    val->len > MT753X_NUM_PORTS)
-		return -EINVAL;
-
-	for (i = 0; i < val->len; i++) {
-		struct switch_port *p = &val->value.ports[i];
-
-		if (p->id >= MT753X_NUM_PORTS)
-			return -EINVAL;
-
-		member |= BIT(p->id);
-
-		if (p->flags & BIT(SWITCH_PORT_FLAG_TAGGED))
-			etags |= BIT(p->id);
-	}
-
-	gsw->vlan_entries[val->port_vlan].member = member;
-	gsw->vlan_entries[val->port_vlan].etags = etags;
-
-	return 0;
-}
-
-static int mt753x_set_vid(struct switch_dev *dev,
-			  const struct switch_attr *attr,
-			  struct switch_val *val)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-	int vlan;
-	u16 vid;
-
-	vlan = val->port_vlan;
-	vid = (u16)val->value.i;
-
-	if (vlan < 0 || vlan >= MT753X_NUM_VLANS)
-		return -EINVAL;
-
-	if (vid < MT753X_MIN_VID || vid > MT753X_MAX_VID)
-		return -EINVAL;
-
-	gsw->vlan_entries[vlan].vid = vid;
-	return 0;
-}
-
-static int mt753x_get_vid(struct switch_dev *dev,
-			  const struct switch_attr *attr,
-			  struct switch_val *val)
-{
-	val->value.i = val->port_vlan;
-	return 0;
-}
-
-static int mt753x_get_port_link(struct switch_dev *dev, int port,
-				struct switch_port_link *link)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-	u32 speed, pmsr;
-
-	if (port < 0 || port >= MT753X_NUM_PORTS)
-		return -EINVAL;
-
-	pmsr = mt753x_reg_read(gsw, PMSR(port));
-
-	link->link = pmsr & MAC_LNK_STS;
-	link->duplex = pmsr & MAC_DPX_STS;
-	speed = (pmsr & MAC_SPD_STS_M) >> MAC_SPD_STS_S;
-
-	switch (speed) {
-	case MAC_SPD_10:
-		link->speed = SWITCH_PORT_SPEED_10;
-		break;
-	case MAC_SPD_100:
-		link->speed = SWITCH_PORT_SPEED_100;
-		break;
-	case MAC_SPD_1000:
-		link->speed = SWITCH_PORT_SPEED_1000;
-		break;
-	case MAC_SPD_2500:
-		/* TODO: swconfig has no support for 2500 now */
-		link->speed = SWITCH_PORT_SPEED_UNKNOWN;
-		break;
-	}
-
-	return 0;
-}
-
-static int mt753x_set_port_link(struct switch_dev *dev, int port,
-				struct switch_port_link *link)
-{
-#ifndef MODULE
-	if (port >= MT753X_NUM_PHYS)
-		return -EINVAL;
-
-	return switch_generic_set_link(dev, port, link);
-#else
-	return -ENOTSUPP;
-#endif
-}
-
-static u64 get_mib_counter(struct gsw_mt753x *gsw, int i, int port)
-{
-	unsigned int offset;
-	u64 lo, hi, hi2;
-
-	offset = mt753x_mibs[i].offset;
-
-	if (mt753x_mibs[i].size == 1)
-		return mt753x_reg_read(gsw, MIB_COUNTER_REG(port, offset));
-
-	do {
-		hi = mt753x_reg_read(gsw, MIB_COUNTER_REG(port, offset + 4));
-		lo = mt753x_reg_read(gsw, MIB_COUNTER_REG(port, offset));
-		hi2 = mt753x_reg_read(gsw, MIB_COUNTER_REG(port, offset + 4));
-	} while (hi2 != hi);
-
-	return (hi << 32) | lo;
-}
-
-static int mt753x_get_port_mib(struct switch_dev *dev,
-			       const struct switch_attr *attr,
-			       struct switch_val *val)
-{
-	static char buf[4096];
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-	int i, len = 0;
-
-	if (val->port_vlan >= MT753X_NUM_PORTS)
-		return -EINVAL;
-
-	len += snprintf(buf + len, sizeof(buf) - len,
-			"Port %d MIB counters\n", val->port_vlan);
-
-	for (i = 0; i < ARRAY_SIZE(mt753x_mibs); ++i) {
-		u64 counter;
-
-		len += snprintf(buf + len, sizeof(buf) - len,
-				"%-11s: ", mt753x_mibs[i].name);
-		counter = get_mib_counter(gsw, i, val->port_vlan);
-		len += snprintf(buf + len, sizeof(buf) - len, "%llu\n",
-				counter);
-	}
-
-	val->value.s = buf;
-	val->len = len;
-	return 0;
-}
-
-static int mt753x_get_port_stats(struct switch_dev *dev, int port,
-				 struct switch_port_stats *stats)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	if (port < 0 || port >= MT753X_NUM_PORTS)
-		return -EINVAL;
-
-	stats->tx_bytes = get_mib_counter(gsw, MT753X_PORT_MIB_TXB_ID, port);
-	stats->rx_bytes = get_mib_counter(gsw, MT753X_PORT_MIB_RXB_ID, port);
-
-	return 0;
-}
-
-static void mt753x_port_isolation(struct gsw_mt753x *gsw)
-{
-	int i;
-
-	for (i = 0; i < MT753X_NUM_PORTS; i++)
-		mt753x_reg_write(gsw, PCR(i),
-				 BIT(gsw->cpu_port) << PORT_MATRIX_S);
-
-	mt753x_reg_write(gsw, PCR(gsw->cpu_port), PORT_MATRIX_M);
-
-	for (i = 0; i < MT753X_NUM_PORTS; i++)
-		mt753x_reg_write(gsw, PVC(i),
-				 (0x8100 << STAG_VPID_S) |
-				 (VA_TRANSPARENT_PORT << VLAN_ATTR_S));
-}
-
-static int mt753x_apply_config(struct switch_dev *dev)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	if (!gsw->global_vlan_enable) {
-		mt753x_port_isolation(gsw);
-		return 0;
-	}
-
-	mt753x_apply_vlan_config(gsw);
-
-	return 0;
-}
-
-static int mt753x_reset_switch(struct switch_dev *dev)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-	int i;
-
-	memset(gsw->port_entries, 0, sizeof(gsw->port_entries));
-	memset(gsw->vlan_entries, 0, sizeof(gsw->vlan_entries));
-
-	/* set default vid of each vlan to the same number of vlan, so the vid
-	 * won't need be set explicitly.
-	 */
-	for (i = 0; i < MT753X_NUM_VLANS; i++)
-		gsw->vlan_entries[i].vid = i;
-
-	return 0;
-}
-
-static int mt753x_phy_read16(struct switch_dev *dev, int addr, u8 reg,
-			     u16 *value)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	*value = gsw->mii_read(gsw, addr, reg);
-
-	return 0;
-}
-
-static int mt753x_phy_write16(struct switch_dev *dev, int addr, u8 reg,
-			      u16 value)
-{
-	struct gsw_mt753x *gsw = container_of(dev, struct gsw_mt753x, swdev);
-
-	gsw->mii_write(gsw, addr, reg, value);
-
-	return 0;
-}
-
-static const struct switch_attr mt753x_global[] = {
-	{
-		.type = SWITCH_TYPE_INT,
-		.name = "enable_vlan",
-		.description = "VLAN mode (1:enabled)",
-		.max = 1,
-		.id = MT753X_ATTR_ENABLE_VLAN,
-		.get = mt753x_get_vlan_enable,
-		.set = mt753x_set_vlan_enable,
-	}
-};
-
-static const struct switch_attr mt753x_port[] = {
-	{
-		.type = SWITCH_TYPE_STRING,
-		.name = "mib",
-		.description = "Get MIB counters for port",
-		.get = mt753x_get_port_mib,
-		.set = NULL,
-	},
-};
-
-static const struct switch_attr mt753x_vlan[] = {
-	{
-		.type = SWITCH_TYPE_INT,
-		.name = "vid",
-		.description = "VLAN ID (0-4094)",
-		.set = mt753x_set_vid,
-		.get = mt753x_get_vid,
-		.max = 4094,
-	},
-};
-
-static const struct switch_dev_ops mt753x_swdev_ops = {
-	.attr_global = {
-		.attr = mt753x_global,
-		.n_attr = ARRAY_SIZE(mt753x_global),
-	},
-	.attr_port = {
-		.attr = mt753x_port,
-		.n_attr = ARRAY_SIZE(mt753x_port),
-	},
-	.attr_vlan = {
-		.attr = mt753x_vlan,
-		.n_attr = ARRAY_SIZE(mt753x_vlan),
-	},
-	.get_vlan_ports = mt753x_get_vlan_ports,
-	.set_vlan_ports = mt753x_set_vlan_ports,
-	.get_port_pvid = mt753x_get_port_pvid,
-	.set_port_pvid = mt753x_set_port_pvid,
-	.get_port_link = mt753x_get_port_link,
-	.set_port_link = mt753x_set_port_link,
-	.get_port_stats = mt753x_get_port_stats,
-	.apply_config = mt753x_apply_config,
-	.reset_switch = mt753x_reset_switch,
-	.phy_read16 = mt753x_phy_read16,
-	.phy_write16 = mt753x_phy_write16,
-};
-
-int mt753x_swconfig_init(struct gsw_mt753x *gsw)
-{
-	struct device_node *np = gsw->dev->of_node;
-	struct switch_dev *swdev;
-	int ret;
-
-	if (of_property_read_u32(np, "mediatek,cpuport", &gsw->cpu_port))
-		gsw->cpu_port = MT753X_DFL_CPU_PORT;
-
-	swdev = &gsw->swdev;
-
-	swdev->name = gsw->name;
-	swdev->alias = gsw->name;
-	swdev->cpu_port = gsw->cpu_port;
-	swdev->ports = MT753X_NUM_PORTS;
-	swdev->vlans = MT753X_NUM_VLANS;
-	swdev->ops = &mt753x_swdev_ops;
-
-	ret = register_switch(swdev, NULL);
-	if (ret) {
-		dev_notice(gsw->dev, "Failed to register switch %s\n",
-			   swdev->name);
-		return ret;
-	}
-
-	mt753x_apply_config(swdev);
-
-	return 0;
-}
-
-void mt753x_swconfig_destroy(struct gsw_mt753x *gsw)
-{
-	unregister_switch(&gsw->swdev);
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_swconfig.h b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_swconfig.h
deleted file mode 100644
index f000364ee8..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_swconfig.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2018 MediaTek Inc.
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-#ifndef _MT753X_SWCONFIG_H_
-#define _MT753X_SWCONFIG_H_
-
-#ifdef CONFIG_SWCONFIG
-#include <linux/switch.h>
-#include "mt753x.h"
-
-int mt753x_swconfig_init(struct gsw_mt753x *gsw);
-void mt753x_swconfig_destroy(struct gsw_mt753x *gsw);
-#else
-static inline int mt753x_swconfig_init(struct gsw_mt753x *gsw)
-{
-	mt753x_apply_vlan_config(gsw);
-
-	return 0;
-}
-
-static inline void mt753x_swconfig_destroy(struct gsw_mt753x *gsw)
-{
-}
-#endif
-
-#endif /* _MT753X_SWCONFIG_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_vlan.c b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_vlan.c
deleted file mode 100644
index 4d88eee8de..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_vlan.c
+++ /dev/null
@@ -1,183 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2018 MediaTek Inc.
- */
-
-#include "mt753x.h"
-#include "mt753x_regs.h"
-
-struct mt753x_mapping mt753x_def_mapping[] = {
-	{
-		.name = "llllw",
-		.pvids = { 1, 1, 1, 1, 2, 2, 1 },
-		.members = { 0, 0x4f, 0x30 },
-		.etags = { 0, 0, 0 },
-		.vids = { 0, 1, 2 },
-	}, {
-		.name = "wllll",
-		.pvids = { 2, 1, 1, 1, 1, 2, 1 },
-		.members = { 0, 0x5e, 0x21 },
-		.etags = { 0, 0, 0 },
-		.vids = { 0, 1, 2 },
-	}, {
-		.name = "lwlll",
-		.pvids = { 1, 2, 1, 1, 1, 2, 1 },
-		.members = { 0, 0x5d, 0x22 },
-		.etags = { 0, 0, 0 },
-		.vids = { 0, 1, 2 },
-	},
-};
-
-void mt753x_vlan_ctrl(struct gsw_mt753x *gsw, u32 cmd, u32 val)
-{
-	int i;
-
-	mt753x_reg_write(gsw, VTCR,
-			 VTCR_BUSY | ((cmd << VTCR_FUNC_S) & VTCR_FUNC_M) |
-			 (val & VTCR_VID_M));
-
-	for (i = 0; i < 300; i++) {
-		u32 val = mt753x_reg_read(gsw, VTCR);
-
-		if ((val & VTCR_BUSY) == 0)
-			break;
-
-		usleep_range(1000, 1100);
-	}
-
-	if (i == 300)
-		dev_info(gsw->dev, "vtcr timeout\n");
-}
-
-static void mt753x_write_vlan_entry(struct gsw_mt753x *gsw, int vlan, u16 vid,
-				    u8 ports, u8 etags)
-{
-	int port;
-	u32 val;
-
-	/* vlan port membership */
-	if (ports)
-		mt753x_reg_write(gsw, VAWD1,
-				 IVL_MAC | VTAG_EN | VENTRY_VALID |
-				 ((ports << PORT_MEM_S) & PORT_MEM_M));
-	else
-		mt753x_reg_write(gsw, VAWD1, 0);
-
-	/* egress mode */
-	val = 0;
-	for (port = 0; port < MT753X_NUM_PORTS; port++) {
-		if (etags & BIT(port))
-			val |= ETAG_CTRL_TAG << PORT_ETAG_S(port);
-		else
-			val |= ETAG_CTRL_UNTAG << PORT_ETAG_S(port);
-	}
-	mt753x_reg_write(gsw, VAWD2, val);
-
-	/* write to vlan table */
-	mt753x_vlan_ctrl(gsw, VTCR_WRITE_VLAN_ENTRY, vid);
-}
-
-void mt753x_apply_vlan_config(struct gsw_mt753x *gsw)
-{
-	int i, j;
-	u8 tag_ports;
-	u8 untag_ports;
-
-	/* set all ports as security mode */
-	for (i = 0; i < MT753X_NUM_PORTS; i++)
-		mt753x_reg_write(gsw, PCR(i),
-				 PORT_MATRIX_M | SECURITY_MODE);
-
-	/* check if a port is used in tag/untag vlan egress mode */
-	tag_ports = 0;
-	untag_ports = 0;
-
-	for (i = 0; i < MT753X_NUM_VLANS; i++) {
-		u8 member = gsw->vlan_entries[i].member;
-		u8 etags = gsw->vlan_entries[i].etags;
-
-		if (!member)
-			continue;
-
-		for (j = 0; j < MT753X_NUM_PORTS; j++) {
-			if (!(member & BIT(j)))
-				continue;
-
-			if (etags & BIT(j))
-				tag_ports |= 1u << j;
-			else
-				untag_ports |= 1u << j;
-		}
-	}
-
-	/* set all untag-only ports as transparent and the rest as user port */
-	for (i = 0; i < MT753X_NUM_PORTS; i++) {
-		u32 pvc_mode = 0x8100 << STAG_VPID_S;
-
-		if (untag_ports & BIT(i) && !(tag_ports & BIT(i)))
-			pvc_mode = (0x8100 << STAG_VPID_S) |
-				(VA_TRANSPARENT_PORT << VLAN_ATTR_S);
-
-		mt753x_reg_write(gsw, PVC(i), pvc_mode);
-	}
-
-	/* first clear the switch vlan table */
-	for (i = 0; i < MT753X_NUM_VLANS; i++)
-		mt753x_write_vlan_entry(gsw, i, i, 0, 0);
-
-	/* now program only vlans with members to avoid
-	 * clobbering remapped entries in later iterations
-	 */
-	for (i = 0; i < MT753X_NUM_VLANS; i++) {
-		u16 vid = gsw->vlan_entries[i].vid;
-		u8 member = gsw->vlan_entries[i].member;
-		u8 etags = gsw->vlan_entries[i].etags;
-
-		if (member)
-			mt753x_write_vlan_entry(gsw, i, vid, member, etags);
-	}
-
-	/* Port Default PVID */
-	for (i = 0; i < MT753X_NUM_PORTS; i++) {
-		int vlan = gsw->port_entries[i].pvid;
-		u16 pvid = 0;
-		u32 val;
-
-		if (vlan < MT753X_NUM_VLANS && gsw->vlan_entries[vlan].member)
-			pvid = gsw->vlan_entries[vlan].vid;
-
-		val = mt753x_reg_read(gsw, PPBV1(i));
-		val &= ~GRP_PORT_VID_M;
-		val |= pvid;
-		mt753x_reg_write(gsw, PPBV1(i), val);
-	}
-}
-
-struct mt753x_mapping *mt753x_find_mapping(struct device_node *np)
-{
-	const char *map;
-	int i;
-
-	if (of_property_read_string(np, "mediatek,portmap", &map))
-		return NULL;
-
-	for (i = 0; i < ARRAY_SIZE(mt753x_def_mapping); i++)
-		if (!strcmp(map, mt753x_def_mapping[i].name))
-			return &mt753x_def_mapping[i];
-
-	return NULL;
-}
-
-void mt753x_apply_mapping(struct gsw_mt753x *gsw, struct mt753x_mapping *map)
-{
-	int i = 0;
-
-	for (i = 0; i < MT753X_NUM_PORTS; i++)
-		gsw->port_entries[i].pvid = map->pvids[i];
-
-	for (i = 0; i < MT753X_NUM_VLANS; i++) {
-		gsw->vlan_entries[i].member = map->members[i];
-		gsw->vlan_entries[i].etags = map->etags[i];
-		gsw->vlan_entries[i].vid = map->vids[i];
-	}
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_vlan.h b/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_vlan.h
deleted file mode 100644
index c726b8eacd..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/mtk/mt753x/mt753x_vlan.h
+++ /dev/null
@@ -1,40 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2018 MediaTek Inc.
- */
-
-#ifndef _MT753X_VLAN_H_
-#define _MT753X_VLAN_H_
-
-#define MT753X_NUM_PORTS	7
-#define MT753X_NUM_VLANS	4095
-#define MT753X_MAX_VID		4095
-#define MT753X_MIN_VID		0
-
-struct gsw_mt753x;
-
-struct mt753x_port_entry {
-	u16	pvid;
-};
-
-struct mt753x_vlan_entry {
-	u16	vid;
-	u8	member;
-	u8	etags;
-};
-
-struct mt753x_mapping {
-	char	*name;
-	u16	pvids[MT753X_NUM_PORTS];
-	u8	members[MT753X_NUM_VLANS];
-	u8	etags[MT753X_NUM_VLANS];
-	u16	vids[MT753X_NUM_VLANS];
-};
-
-extern struct mt753x_mapping mt753x_defaults[];
-
-void mt753x_vlan_ctrl(struct gsw_mt753x *gsw, u32 cmd, u32 val);
-void mt753x_apply_vlan_config(struct gsw_mt753x *gsw);
-struct mt753x_mapping *mt753x_find_mapping(struct device_node *np);
-void mt753x_apply_mapping(struct gsw_mt753x *gsw, struct mt753x_mapping *map);
-#endif /* _MT753X_VLAN_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/Makefile b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/Makefile
deleted file mode 100644
index 0f2891ead4..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/Makefile
+++ /dev/null
@@ -1,66 +0,0 @@
-obj-$(CONFIG_RTL8367S_GSW) += rtl8367s_gsw.o
-rtl8367s_gsw-objs := rtl8367s_mdio.o rtl8367s_dbg.o
-ifeq ($(CONFIG_SWCONFIG),y)
-rtl8367s_gsw-objs += rtl8367s.o
-endif
-rtl8367s_gsw-objs += rtl8367c/acl.o
-rtl8367s_gsw-objs += rtl8367c/cpu.o
-rtl8367s_gsw-objs += rtl8367c/dot1x.o
-rtl8367s_gsw-objs += rtl8367c/eee.o
-rtl8367s_gsw-objs += rtl8367c/igmp.o
-rtl8367s_gsw-objs += rtl8367c/interrupt.o
-rtl8367s_gsw-objs += rtl8367c/l2.o
-rtl8367s_gsw-objs += rtl8367c/leaky.o
-rtl8367s_gsw-objs += rtl8367c/led.o
-rtl8367s_gsw-objs += rtl8367c/mirror.o
-rtl8367s_gsw-objs += rtl8367c/oam.o
-rtl8367s_gsw-objs += rtl8367c/port.o
-rtl8367s_gsw-objs += rtl8367c/ptp.o
-rtl8367s_gsw-objs += rtl8367c/qos.o
-rtl8367s_gsw-objs += rtl8367c/rate.o
-rtl8367s_gsw-objs += rtl8367c/rldp.o
-rtl8367s_gsw-objs += rtl8367c/rtk_switch.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_acl.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_cputag.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_dot1x.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_eav.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_eee.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_fc.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_green.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_hsb.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_igmp.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_inbwctrl.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_interrupt.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_led.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_lut.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_meter.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_mib.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_mirror.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_misc.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_oam.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_phy.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_port.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_portIsolation.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_qos.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_rldp.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_rma.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_scheduling.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_storm.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_svlan.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_trunking.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_unknownMulticast.o
-rtl8367s_gsw-objs += rtl8367c/rtl8367c_asicdrv_vlan.o
-rtl8367s_gsw-objs += rtl8367c/smi.o
-rtl8367s_gsw-objs += rtl8367c/stat.o
-rtl8367s_gsw-objs += rtl8367c/storm.o
-rtl8367s_gsw-objs += rtl8367c/svlan.o
-rtl8367s_gsw-objs += rtl8367c/trap.o
-rtl8367s_gsw-objs += rtl8367c/trunk.o
-rtl8367s_gsw-objs += rtl8367c/vlan.o
-
-ccflags-y += -Werror -D_LITTLE_ENDIAN -DMDC_MDIO_OPERATION
-
-ccflags-y += -Idrivers/net/phy/rtk/rtl8367c/include
-ccflags-y += -Iinclude/linux/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/modules.builtin b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/modules.builtin
deleted file mode 100644
index 961a70a150..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/modules.builtin
+++ /dev/null
@@ -1 +0,0 @@
-kernel/drivers/net/phy/rtk/rtl8367s_gsw.ko
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/acl.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/acl.c
deleted file mode 100644
index 75e5a5e740..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/acl.c
+++ /dev/null
@@ -1,2061 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in ACL module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <acl.h>
-#include <vlan.h>
-#include <svlan.h>
-#include <rate.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_acl.h>
-#include <rtl8367c_asicdrv_hsb.h>
-#include <rtl8367c_asicdrv_vlan.h>
-#include <rtl8367c_asicdrv_svlan.h>
-#include <rtl8367c_asicdrv_cputag.h>
-#include <rtl8367c_asicdrv_mib.h>
-
-CONST_T rtk_uint8 filter_templateField[RTL8367C_ACLTEMPLATENO][RTL8367C_ACLRULEFIELDNO] = {
-    {ACL_DMAC0,             ACL_DMAC1,          ACL_DMAC2,          ACL_SMAC0,          ACL_SMAC1,          ACL_SMAC2,          ACL_ETHERTYPE,      ACL_FIELD_SELECT15},
-    {ACL_IP4SIP0,           ACL_IP4SIP1,        ACL_IP4DIP0,        ACL_IP4DIP1,        ACL_FIELD_SELECT13, ACL_FIELD_SELECT14, ACL_FIELD_SELECT02, ACL_FIELD_SELECT15},
-    {ACL_IP6SIP0WITHIPV4,   ACL_IP6SIP1WITHIPV4,ACL_FIELD_SELECT03, ACL_FIELD_SELECT04, ACL_FIELD_SELECT05, ACL_FIELD_SELECT06, ACL_FIELD_SELECT07, ACL_FIELD_SELECT08},
-    {ACL_IP6DIP0WITHIPV4,   ACL_IP6DIP1WITHIPV4,ACL_FIELD_SELECT09, ACL_FIELD_SELECT10, ACL_FIELD_SELECT11, ACL_FIELD_SELECT12, ACL_FIELD_SELECT13, ACL_FIELD_SELECT14},
-    {ACL_VIDRANGE,          ACL_IPRANGE,        ACL_PORTRANGE,      ACL_CTAG,           ACL_STAG,           ACL_FIELD_SELECT13, ACL_FIELD_SELECT14, ACL_FIELD_SELECT15}
-};
-
-CONST_T rtk_uint8 filter_advanceCaretagField[RTL8367C_ACLTEMPLATENO][2] = {
-    {TRUE,      7},
-    {TRUE,      7},
-    {FALSE,     0},
-    {FALSE,     0},
-    {TRUE,      7},
-};
-
-
-CONST_T rtk_uint8 filter_fieldTemplateIndex[FILTER_FIELD_END][RTK_FILTER_FIELD_USED_MAX] = {
-    {0x00, 0x01,0x02},
-    {0x03, 0x04,0x05},
-    {0x06},
-    {0x43},
-    {0x44},
-    {0x10, 0x11},
-    {0x12, 0x13},
-    {0x24},
-    {0x25},
-    {0x35},
-    {0x35},
-    {0x20, 0x21,0x22,0x23},
-    {0x30, 0x31,0x32,0x33},
-    {0x26},
-    {0x27},
-    {0x14},
-    {0x15},
-    {0x16},
-    {0x14},
-    {0x15},
-    {0x14},
-    {0x14},
-    {0x14},
-
-    {0x40},
-    {0x41},
-    {0x42},
-
-    {0x14},
-    {0x15},
-    {0x16},
-    {0x22},
-    {0x23},
-    {0x24},
-    {0x25},
-    {0x26},
-    {0x27},
-    {0x32},
-    {0x33},
-    {0x34},
-    {0x35},
-    {0x36},
-    {0x37},
-    {0x47},
-
-    {0xFF} /* Pattern Match */
-};
-
-CONST_T rtk_uint8 filter_fieldSize[FILTER_FIELD_END] = {
-    3, 3, 1, 1, 1,
-    2, 2, 1, 1, 1, 1, 4, 4, 1, 1,
-    1, 1, 1, 1, 1, 1, 1, 1,
-    1, 1, 1,
-    1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
-    8
-};
-
-CONST_T rtk_uint16 field_selector[RTL8367C_FIELDSEL_FORMAT_NUMBER][2] =
-{
-    {FIELDSEL_FORMAT_DEFAULT, 0},    /* Field Selector 0 */
-    {FIELDSEL_FORMAT_DEFAULT, 0},    /* Field Selector 1 */
-    {FIELDSEL_FORMAT_IPPAYLOAD, 12}, /* Field Selector 2 */
-    {FIELDSEL_FORMAT_IPV6, 10},      /* Field Selector 3 */
-    {FIELDSEL_FORMAT_IPV6, 8},       /* Field Selector 4 */
-    {FIELDSEL_FORMAT_IPV4, 0},       /* Field Selector 5 */
-    {FIELDSEL_FORMAT_IPV4, 8},       /* Field Selector 6 */
-    {FIELDSEL_FORMAT_IPV6, 0},       /* Field Selector 7 */
-    {FIELDSEL_FORMAT_IPV6, 6},       /* Field Selector 8 */
-    {FIELDSEL_FORMAT_IPV6, 26},      /* Field Selector 9 */
-    {FIELDSEL_FORMAT_IPV6, 24},      /* Field Selector 10 */
-    {FIELDSEL_FORMAT_DEFAULT, 0},    /* Field Selector 11 */
-    {FIELDSEL_FORMAT_IPV4, 6},       /* Field Selector 12 */
-    {FIELDSEL_FORMAT_IPPAYLOAD, 0},  /* Field Selector 13 */
-    {FIELDSEL_FORMAT_IPPAYLOAD, 2},  /* Field Selector 14 */
-    {FIELDSEL_FORMAT_DEFAULT, 0}     /* Field Selector 15 */
-};
-
-
-static rtk_api_ret_t _rtk_filter_igrAcl_writeDataField(rtl8367c_aclrule *aclRule, rtk_filter_field_t *fieldPtr);
-
-
-/* Function Name:
- *      rtk_filter_igrAcl_init
- * Description:
- *      ACL initialization function
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Pointer pFilter_field or pFilter_cfg point to NULL.
- * Note:
- *      This function enable and intialize ACL function
- */
-rtk_api_ret_t rtk_filter_igrAcl_init(void)
-{
-    rtl8367c_acltemplate_t       aclTemp;
-    rtk_uint32                 i, j;
-    rtk_api_ret_t          ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((ret = rtk_filter_igrAcl_cfg_delAll()) != RT_ERR_OK)
-        return ret;
-
-    for(i = 0; i < RTL8367C_ACLTEMPLATENO; i++)
-    {
-        for(j = 0; j < RTL8367C_ACLRULEFIELDNO;j++)
-            aclTemp.field[j] = filter_templateField[i][j];
-
-        if ((ret = rtl8367c_setAsicAclTemplate(i, &aclTemp)) != RT_ERR_OK)
-            return ret;
-    }
-
-    for(i = 0; i < RTL8367C_FIELDSEL_FORMAT_NUMBER; i++)
-    {
-        if ((ret = rtl8367c_setAsicFieldSelector(i, field_selector[i][0], field_selector[i][1])) != RT_ERR_OK)
-            return ret;
-    }
-
-    RTK_SCAN_ALL_PHY_PORTMASK(i)
-    {
-        if ((ret = rtl8367c_setAsicAcl(i, TRUE)) != RT_ERR_OK)
-            return ret;
-
-        if ((ret = rtl8367c_setAsicAclUnmatchedPermit(i, TRUE)) != RT_ERR_OK)
-            return ret;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_field_add
- * Description:
- *      Add comparison rule to an ACL configuration
- * Input:
- *      pFilter_cfg     - The ACL configuration that this function will add comparison rule
- *      pFilter_field   - The comparison rule that will be added.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Pointer pFilter_field or pFilter_cfg point to NULL.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      This function add a comparison rule (*pFilter_field) to an ACL configuration (*pFilter_cfg).
- *      Pointer pFilter_cfg points to an ACL configuration structure, this structure keeps multiple ACL
- *      comparison rules by means of linked list. Pointer pFilter_field will be added to linked
- *      list keeped by structure that pFilter_cfg points to.
- */
-rtk_api_ret_t rtk_filter_igrAcl_field_add(rtk_filter_cfg_t* pFilter_cfg, rtk_filter_field_t* pFilter_field)
-{
-    rtk_uint32 i;
-    rtk_filter_field_t *tailPtr;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pFilter_cfg || NULL == pFilter_field)
-        return RT_ERR_NULL_POINTER;
-
-    if(pFilter_field->fieldType >= FILTER_FIELD_END)
-        return RT_ERR_ENTRY_INDEX;
-
-
-    if(0 == pFilter_field->fieldTemplateNo)
-    {
-        pFilter_field->fieldTemplateNo = filter_fieldSize[pFilter_field->fieldType];
-
-        for(i = 0; i < pFilter_field->fieldTemplateNo; i++)
-        {
-            pFilter_field->fieldTemplateIdx[i] = filter_fieldTemplateIndex[pFilter_field->fieldType][i];
-        }
-    }
-
-    if(NULL == pFilter_cfg->fieldHead)
-    {
-        pFilter_cfg->fieldHead = pFilter_field;
-    }
-    else
-    {
-        if (pFilter_cfg->fieldHead->next == NULL)
-        {
-            pFilter_cfg->fieldHead->next = pFilter_field;
-        }
-        else
-        {
-            tailPtr = pFilter_cfg->fieldHead->next;
-            while( tailPtr->next != NULL)
-            {
-                tailPtr = tailPtr->next;
-            }
-            tailPtr->next = pFilter_field;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-static rtk_api_ret_t _rtk_filter_igrAcl_writeDataField(rtl8367c_aclrule *aclRule, rtk_filter_field_t *fieldPtr)
-{
-    rtk_uint32 i, tempIdx,fieldIdx, ipValue, ipMask;
-    rtk_uint32 ip6addr[RTK_IPV6_ADDR_WORD_LENGTH];
-    rtk_uint32 ip6mask[RTK_IPV6_ADDR_WORD_LENGTH];
-
-    for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-    {
-        tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-
-        aclRule[tempIdx].valid = TRUE;
-    }
-
-    switch (fieldPtr->fieldType)
-    {
-    /* use DMAC structure as representative for mac structure */
-    case FILTER_FIELD_DMAC:
-    case FILTER_FIELD_SMAC:
-
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.mac.value.octet[5 - i*2] | (fieldPtr->filter_pattern_union.mac.value.octet[5 - (i*2 + 1)] << 8);
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.mac.mask.octet[5 - i*2] | (fieldPtr->filter_pattern_union.mac.mask.octet[5 - (i*2 + 1)] << 8);
-        }
-        break;
-    case FILTER_FIELD_ETHERTYPE:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.etherType.value;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.etherType.mask;
-        }
-        break;
-    case FILTER_FIELD_IPV4_SIP:
-    case FILTER_FIELD_IPV4_DIP:
-
-        ipValue = fieldPtr->filter_pattern_union.sip.value;
-        ipMask = fieldPtr->filter_pattern_union.sip.mask;
-
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = (0xFFFF & (ipValue >> (i*16)));
-            aclRule[tempIdx].care_bits.field[fieldIdx] = (0xFFFF & (ipMask >> (i*16)));
-        }
-        break;
-    case FILTER_FIELD_IPV4_TOS:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.ipTos.value & 0xFF;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.ipTos.mask  & 0xFF;
-        }
-        break;
-    case FILTER_FIELD_IPV4_PROTOCOL:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.protocol.value & 0xFF;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.protocol.mask  & 0xFF;
-        }
-        break;
-    case FILTER_FIELD_IPV6_SIPV6:
-    case FILTER_FIELD_IPV6_DIPV6:
-        for(i = 0; i < RTK_IPV6_ADDR_WORD_LENGTH; i++)
-        {
-            ip6addr[i] = fieldPtr->filter_pattern_union.sipv6.value.addr[i];
-            ip6mask[i] = fieldPtr->filter_pattern_union.sipv6.mask.addr[i];
-        }
-
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            if(i < 2)
-            {
-                aclRule[tempIdx].data_bits.field[fieldIdx] = ((ip6addr[0] & (0xFFFF << (i * 16))) >> (i * 16));
-                aclRule[tempIdx].care_bits.field[fieldIdx] = ((ip6mask[0] & (0xFFFF << (i * 16))) >> (i * 16));
-            }
-            else
-            {
-                /*default acl template for ipv6 address supports MSB 32-bits and LSB 32-bits only*/
-                aclRule[tempIdx].data_bits.field[fieldIdx] = ((ip6addr[3] & (0xFFFF << ((i&1) * 16))) >> ((i&1) * 16));
-                aclRule[tempIdx].care_bits.field[fieldIdx] = ((ip6mask[3] & (0xFFFF << ((i&1) * 16))) >> ((i&1) * 16));
-            }
-        }
-
-        break;
-    case FILTER_FIELD_CTAG:
-    case FILTER_FIELD_STAG:
-
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = (fieldPtr->filter_pattern_union.l2tag.pri.value << 13) | (fieldPtr->filter_pattern_union.l2tag.cfi.value << 12) | fieldPtr->filter_pattern_union.l2tag.vid.value;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = (fieldPtr->filter_pattern_union.l2tag.pri.mask << 13) | (fieldPtr->filter_pattern_union.l2tag.cfi.mask << 12) | fieldPtr->filter_pattern_union.l2tag.vid.mask;
-        }
-        break;
-    case FILTER_FIELD_IPV4_FLAG:
-
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] &= 0x1FFF;
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.ipFlag.xf.value << 15);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.ipFlag.df.value << 14);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.ipFlag.mf.value << 13);
-
-            aclRule[tempIdx].care_bits.field[fieldIdx] &= 0x1FFF;
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.ipFlag.xf.mask << 15);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.ipFlag.df.mask << 14);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.ipFlag.mf.mask << 13);
-        }
-
-        break;
-    case FILTER_FIELD_IPV4_OFFSET:
-
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] &= 0xE000;
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= fieldPtr->filter_pattern_union.inData.value;
-
-            aclRule[tempIdx].care_bits.field[fieldIdx] &= 0xE000;
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= fieldPtr->filter_pattern_union.inData.mask;
-        }
-
-        break;
-
-    case FILTER_FIELD_IPV6_TRAFFIC_CLASS:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = (fieldPtr->filter_pattern_union.inData.value << 4)&0x0FF0;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = (fieldPtr->filter_pattern_union.inData.mask << 4)&0x0FF0;
-        }
-        break;
-    case FILTER_FIELD_IPV6_NEXT_HEADER:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.inData.value << 8;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.inData.mask << 8;
-        }
-        break;
-    case FILTER_FIELD_TCP_SPORT:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.tcpSrcPort.value;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.tcpSrcPort.mask;
-        }
-        break;
-    case FILTER_FIELD_TCP_DPORT:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.tcpDstPort.value;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.tcpDstPort.mask;
-        }
-        break;
-    case FILTER_FIELD_TCP_FLAG:
-
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.cwr.value << 7);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.ece.value << 6);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.urg.value << 5);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.ack.value << 4);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.psh.value << 3);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.rst.value << 2);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.syn.value << 1);
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= fieldPtr->filter_pattern_union.tcpFlag.fin.value;
-
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.cwr.mask << 7);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.ece.mask << 6);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.urg.mask << 5);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.ack.mask << 4);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.psh.mask << 3);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.rst.mask << 2);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.tcpFlag.syn.mask << 1);
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= fieldPtr->filter_pattern_union.tcpFlag.fin.mask;
-        }
-        break;
-    case FILTER_FIELD_UDP_SPORT:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.udpSrcPort.value;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.udpSrcPort.mask;
-        }
-        break;
-    case FILTER_FIELD_UDP_DPORT:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.udpDstPort.value;
-            aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.udpDstPort.mask;
-        }
-        break;
-    case FILTER_FIELD_ICMP_CODE:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] &= 0xFF00;
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= fieldPtr->filter_pattern_union.icmpCode.value;
-            aclRule[tempIdx].care_bits.field[fieldIdx] &= 0xFF00;
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= fieldPtr->filter_pattern_union.icmpCode.mask;
-        }
-        break;
-    case FILTER_FIELD_ICMP_TYPE:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] &= 0x00FF;
-            aclRule[tempIdx].data_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.icmpType.value << 8);
-            aclRule[tempIdx].care_bits.field[fieldIdx] &= 0x00FF;
-            aclRule[tempIdx].care_bits.field[fieldIdx] |= (fieldPtr->filter_pattern_union.icmpType.mask << 8);
-        }
-        break;
-    case FILTER_FIELD_IGMP_TYPE:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = (fieldPtr->filter_pattern_union.igmpType.value << 8);
-            aclRule[tempIdx].care_bits.field[fieldIdx] = (fieldPtr->filter_pattern_union.igmpType.mask << 8);
-        }
-        break;
-    case FILTER_FIELD_PATTERN_MATCH:
-        for(i = 0; i < fieldPtr->fieldTemplateNo; i++)
-        {
-            tempIdx = (fieldPtr->fieldTemplateIdx[i] & 0xF0) >> 4;
-            fieldIdx = fieldPtr->fieldTemplateIdx[i] & 0x0F;
-
-            aclRule[tempIdx].data_bits.field[fieldIdx] = ((fieldPtr->filter_pattern_union.pattern.value[i/2] >> (16 * (i%2))) & 0x0000FFFF );
-            aclRule[tempIdx].care_bits.field[fieldIdx] = ((fieldPtr->filter_pattern_union.pattern.mask[i/2] >> (16 * (i%2))) & 0x0000FFFF );
-        }
-        break;
-    case FILTER_FIELD_VID_RANGE:
-    case FILTER_FIELD_IP_RANGE:
-    case FILTER_FIELD_PORT_RANGE:
-    default:
-        tempIdx = (fieldPtr->fieldTemplateIdx[0] & 0xF0) >> 4;
-        fieldIdx = fieldPtr->fieldTemplateIdx[0] & 0x0F;
-
-        aclRule[tempIdx].data_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.inData.value;
-        aclRule[tempIdx].care_bits.field[fieldIdx] = fieldPtr->filter_pattern_union.inData.mask;
-        break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_add
- * Description:
- *      Add an ACL configuration to ASIC
- * Input:
- *      filter_id       - Start index of ACL configuration.
- *      pFilter_cfg     - The ACL configuration that this function will add comparison rule
- *      pFilter_action  - Action(s) of ACL configuration.
- * Output:
- *      ruleNum - number of rules written in acl table
- * Return:
- *      RT_ERR_OK                               - OK
- *      RT_ERR_FAILED                           - Failed
- *      RT_ERR_SMI                              - SMI access error
- *      RT_ERR_NULL_POINTER                     - Pointer pFilter_field or pFilter_cfg point to NULL.
- *      RT_ERR_INPUT                            - Invalid input parameters.
- *      RT_ERR_ENTRY_INDEX                      - Invalid filter_id .
- *      RT_ERR_NULL_POINTER                     - Pointer pFilter_action or pFilter_cfg point to NULL.
- *      RT_ERR_FILTER_INACL_ACT_NOT_SUPPORT     - Action is not supported in this chip.
- *      RT_ERR_FILTER_INACL_RULE_NOT_SUPPORT    - Rule is not supported.
- * Note:
- *      This function store pFilter_cfg, pFilter_action into ASIC. The starting
- *      index(es) is filter_id.
- */
-rtk_api_ret_t rtk_filter_igrAcl_cfg_add(rtk_filter_id_t filter_id, rtk_filter_cfg_t* pFilter_cfg, rtk_filter_action_t* pFilter_action, rtk_filter_number_t *ruleNum)
-{
-    rtk_api_ret_t               retVal;
-    rtk_uint32                  careTagData, careTagMask;
-    rtk_uint32                  i,vidx, svidx, actType, ruleId;
-    rtk_uint32                  aclActCtrl;
-    rtk_uint32                  cpuPort;
-    rtk_filter_field_t*         fieldPtr;
-    rtl8367c_aclrule            aclRule[RTL8367C_ACLTEMPLATENO];
-    rtl8367c_aclrule            tempRule;
-    rtl8367c_acl_act_t          aclAct;
-    rtk_uint32                  noRulesAdd;
-    rtk_uint32                  portmask;
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(filter_id > RTL8367C_ACLRULEMAX )
-        return RT_ERR_ENTRY_INDEX;
-
-    if((NULL == pFilter_cfg) || (NULL == pFilter_action) || (NULL == ruleNum))
-        return RT_ERR_NULL_POINTER;
-
-    fieldPtr = pFilter_cfg->fieldHead;
-
-    /* init RULE */
-    for(i = 0; i < RTL8367C_ACLTEMPLATENO; i++)
-    {
-        memset(&aclRule[i], 0, sizeof(rtl8367c_aclrule));
-
-        aclRule[i].data_bits.type= i;
-        aclRule[i].care_bits.type= 0x7;
-    }
-
-    while(NULL != fieldPtr)
-    {
-        _rtk_filter_igrAcl_writeDataField(aclRule, fieldPtr);
-
-        fieldPtr = fieldPtr->next;
-    }
-
-    /*set care tag mask in User Defined Field 15*/
-    /*Follow care tag should not be used while ACL template and User defined fields are fully control by system designer*/
-    /*those advanced packet type care tag is used in default template design structure only*/
-    careTagData = 0;
-    careTagMask = 0;
-
-    for(i = CARE_TAG_TCP; i < CARE_TAG_END; i++)
-    {
-        if(pFilter_cfg->careTag.tagType[i].mask)
-            careTagMask = careTagMask | (1 << (i-CARE_TAG_TCP));
-
-        if(pFilter_cfg->careTag.tagType[i].value)
-            careTagData = careTagData | (1 << (i-CARE_TAG_TCP));
-    }
-
-    if(careTagData || careTagMask)
-    {
-        i = 0;
-        while(i < RTL8367C_ACLTEMPLATENO)
-        {
-            if(aclRule[i].valid == 1 && filter_advanceCaretagField[i][0] == TRUE)
-            {
-
-                aclRule[i].data_bits.field[filter_advanceCaretagField[i][1]] = careTagData & 0xFFFF;
-                aclRule[i].care_bits.field[filter_advanceCaretagField[i][1]] = careTagMask & 0xFFFF;
-                break;
-            }
-            i++;
-        }
-        /*none of previous used template containing field 15*/
-        if(i == RTL8367C_ACLTEMPLATENO)
-        {
-            i = 0;
-            while(i < RTL8367C_ACLTEMPLATENO)
-            {
-                if(filter_advanceCaretagField[i][0] == TRUE)
-                {
-                    aclRule[i].data_bits.field[filter_advanceCaretagField[i][1]] = careTagData & 0xFFFF;
-                    aclRule[i].care_bits.field[filter_advanceCaretagField[i][1]] = careTagMask & 0xFFFF;
-                    aclRule[i].valid = 1;
-                    break;
-                }
-                i++;
-            }
-        }
-    }
-
-    /*Check rule number*/
-    noRulesAdd = 0;
-    for(i = 0; i < RTL8367C_ACLTEMPLATENO; i++)
-    {
-        if(1 == aclRule[i].valid)
-        {
-            noRulesAdd ++;
-        }
-    }
-
-    *ruleNum = noRulesAdd;
-
-    if((filter_id + noRulesAdd - 1) > RTL8367C_ACLRULEMAX)
-    {
-        return RT_ERR_ENTRY_INDEX;
-    }
-
-    /*set care tag mask in TAG Indicator*/
-    careTagData = 0;
-    careTagMask = 0;
-
-    for(i = 0; i <= CARE_TAG_IPV6;i++)
-    {
-        if(0 == pFilter_cfg->careTag.tagType[i].mask )
-        {
-            careTagMask &=  ~(1 << i);
-        }
-        else
-        {
-            careTagMask |= (1 << i);
-            if(0 == pFilter_cfg->careTag.tagType[i].value )
-                careTagData &= ~(1 << i);
-            else
-                careTagData |= (1 << i);
-        }
-    }
-
-    for(i = 0; i < RTL8367C_ACLTEMPLATENO; i++)
-    {
-        aclRule[i].data_bits.tag_exist = (careTagData) & ACL_RULE_CARETAG_MASK;
-        aclRule[i].care_bits.tag_exist = (careTagMask) & ACL_RULE_CARETAG_MASK;
-    }
-
-    RTK_CHK_PORTMASK_VALID(&pFilter_cfg->activeport.value);
-    RTK_CHK_PORTMASK_VALID(&pFilter_cfg->activeport.mask);
-
-    for(i = 0; i < RTL8367C_ACLTEMPLATENO; i++)
-    {
-        if(TRUE == aclRule[i].valid)
-        {
-            if(rtk_switch_portmask_L2P_get(&pFilter_cfg->activeport.value, &portmask) != RT_ERR_OK)
-                return RT_ERR_PORT_MASK;
-
-            aclRule[i].data_bits.active_portmsk = portmask;
-
-            if(rtk_switch_portmask_L2P_get(&pFilter_cfg->activeport.mask, &portmask) != RT_ERR_OK)
-                return RT_ERR_PORT_MASK;
-
-            aclRule[i].care_bits.active_portmsk = portmask;
-        }
-    }
-
-    if(pFilter_cfg->invert >= FILTER_INVERT_END )
-        return RT_ERR_INPUT;
-
-
-    /*Last action gets high priority if actions are the same*/
-    memset(&aclAct, 0, sizeof(rtl8367c_acl_act_t));
-    aclActCtrl = 0;
-    for(actType = 0; actType < FILTER_ENACT_END; actType ++)
-    {
-        if(pFilter_action->actEnable[actType])
-        {
-            switch (actType)
-            {
-            case FILTER_ENACT_CVLAN_INGRESS:
-                if(pFilter_action->filterCvlanVid > RTL8367C_EVIDMAX)
-                    return RT_ERR_INPUT;
-
-                if((retVal = rtk_vlan_checkAndCreateMbr(pFilter_action->filterCvlanVid, &vidx)) != RT_ERR_OK)
-                {
-                    return retVal;
-                }
-                aclAct.cact = FILTER_ENACT_CVLAN_TYPE(actType);
-                aclAct.cvidx_cact = vidx;
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_TAGONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_VLANONLY;
-                }
-
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-            case FILTER_ENACT_CVLAN_EGRESS:
-                if(pFilter_action->filterCvlanVid > RTL8367C_EVIDMAX)
-                    return RT_ERR_INPUT;
-
-                if((retVal = rtk_vlan_checkAndCreateMbr(pFilter_action->filterCvlanVid, &vidx)) != RT_ERR_OK)
-                    return retVal;
-
-                aclAct.cact = FILTER_ENACT_CVLAN_TYPE(actType);
-                aclAct.cvidx_cact = vidx;
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_TAGONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_VLANONLY;
-                }
-
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-             case FILTER_ENACT_CVLAN_SVID:
-
-                aclAct.cact = FILTER_ENACT_CVLAN_TYPE(actType);
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_TAGONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_VLANONLY;
-                }
-
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-             case FILTER_ENACT_POLICING_1:
-                if(pFilter_action->filterPolicingIdx[1] >= (RTK_METER_NUM + RTL8367C_MAX_LOG_CNT_NUM))
-                    return RT_ERR_INPUT;
-
-                aclAct.cact = FILTER_ENACT_CVLAN_TYPE(actType);
-                aclAct.cvidx_cact = pFilter_action->filterPolicingIdx[1];
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_TAGONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_VLANONLY;
-                }
-
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-
-            case FILTER_ENACT_SVLAN_INGRESS:
-            case FILTER_ENACT_SVLAN_EGRESS:
-
-                if((retVal = rtk_svlan_checkAndCreateMbr(pFilter_action->filterSvlanVid, &svidx)) != RT_ERR_OK)
-                    return retVal;
-
-                aclAct.sact = FILTER_ENACT_SVLAN_TYPE(actType);
-                aclAct.svidx_sact = svidx;
-                aclActCtrl |= FILTER_ENACT_SVLAN_MASK;
-                break;
-            case FILTER_ENACT_SVLAN_CVID:
-
-                aclAct.sact = FILTER_ENACT_SVLAN_TYPE(actType);
-                aclActCtrl |= FILTER_ENACT_SVLAN_MASK;
-                break;
-            case FILTER_ENACT_POLICING_2:
-                if(pFilter_action->filterPolicingIdx[2] >= (RTK_METER_NUM + RTL8367C_MAX_LOG_CNT_NUM))
-                    return RT_ERR_INPUT;
-
-                aclAct.sact = FILTER_ENACT_SVLAN_TYPE(actType);
-                aclAct.svidx_sact = pFilter_action->filterPolicingIdx[2];
-                aclActCtrl |= FILTER_ENACT_SVLAN_MASK;
-                break;
-            case FILTER_ENACT_POLICING_0:
-                if(pFilter_action->filterPolicingIdx[0] >= (RTK_METER_NUM + RTL8367C_MAX_LOG_CNT_NUM))
-                    return RT_ERR_INPUT;
-
-                aclAct.aclmeteridx = pFilter_action->filterPolicingIdx[0];
-                aclActCtrl |= FILTER_ENACT_POLICING_MASK;
-                break;
-            case FILTER_ENACT_PRIORITY:
-            case FILTER_ENACT_1P_REMARK:
-                if(pFilter_action->filterPriority > RTL8367C_PRIMAX)
-                    return RT_ERR_INPUT;
-
-                aclAct.priact = FILTER_ENACT_PRI_TYPE(actType);
-                aclAct.pridx = pFilter_action->filterPriority;
-                aclActCtrl |= FILTER_ENACT_PRIORITY_MASK;
-                break;
-            case FILTER_ENACT_DSCP_REMARK:
-                if(pFilter_action->filterPriority > RTL8367C_DSCPMAX)
-                    return RT_ERR_INPUT;
-
-                aclAct.priact = FILTER_ENACT_PRI_TYPE(actType);
-                aclAct.pridx = pFilter_action->filterPriority;
-                aclActCtrl |= FILTER_ENACT_PRIORITY_MASK;
-                break;
-            case FILTER_ENACT_POLICING_3:
-                if(pFilter_action->filterPriority >= (RTK_METER_NUM + RTL8367C_MAX_LOG_CNT_NUM))
-                    return RT_ERR_INPUT;
-
-                aclAct.priact = FILTER_ENACT_PRI_TYPE(actType);
-                aclAct.pridx = pFilter_action->filterPolicingIdx[3];
-                aclActCtrl |= FILTER_ENACT_PRIORITY_MASK;
-                break;
-            case FILTER_ENACT_DROP:
-
-                aclAct.fwdact = FILTER_ENACT_FWD_TYPE(FILTER_ENACT_REDIRECT);
-                aclAct.fwdact_ext = FALSE;
-
-                aclAct.fwdpmask = 0;
-                aclActCtrl |= FILTER_ENACT_FWD_MASK;
-                break;
-            case FILTER_ENACT_REDIRECT:
-                RTK_CHK_PORTMASK_VALID(&pFilter_action->filterPortmask);
-
-                aclAct.fwdact = FILTER_ENACT_FWD_TYPE(actType);
-                aclAct.fwdact_ext = FALSE;
-
-                if(rtk_switch_portmask_L2P_get(&pFilter_action->filterPortmask, &portmask) != RT_ERR_OK)
-                    return RT_ERR_PORT_MASK;
-                aclAct.fwdpmask = portmask;
-
-                aclActCtrl |= FILTER_ENACT_FWD_MASK;
-                break;
-
-            case FILTER_ENACT_ADD_DSTPORT:
-                RTK_CHK_PORTMASK_VALID(&pFilter_action->filterPortmask);
-
-                aclAct.fwdact = FILTER_ENACT_FWD_TYPE(actType);
-                aclAct.fwdact_ext = FALSE;
-
-                if(rtk_switch_portmask_L2P_get(&pFilter_action->filterPortmask, &portmask) != RT_ERR_OK)
-                    return RT_ERR_PORT_MASK;
-                aclAct.fwdpmask = portmask;
-
-                aclActCtrl |= FILTER_ENACT_FWD_MASK;
-                break;
-            case FILTER_ENACT_MIRROR:
-                RTK_CHK_PORTMASK_VALID(&pFilter_action->filterPortmask);
-
-                aclAct.fwdact = FILTER_ENACT_FWD_TYPE(actType);
-                aclAct.cact_ext = FALSE;
-
-                if(rtk_switch_portmask_L2P_get(&pFilter_action->filterPortmask, &portmask) != RT_ERR_OK)
-                    return RT_ERR_PORT_MASK;
-                aclAct.fwdpmask = portmask;
-
-                aclActCtrl |= FILTER_ENACT_FWD_MASK;
-                break;
-            case FILTER_ENACT_TRAP_CPU:
-
-                aclAct.fwdact = FILTER_ENACT_FWD_TYPE(actType);
-                aclAct.fwdact_ext = FALSE;
-
-                aclActCtrl |= FILTER_ENACT_FWD_MASK;
-                break;
-            case FILTER_ENACT_COPY_CPU:
-                if((retVal = rtl8367c_getAsicCputagTrapPort(&cpuPort)) != RT_ERR_OK)
-                    return retVal;
-
-                aclAct.fwdact = FILTER_ENACT_FWD_TYPE(FILTER_ENACT_MIRROR);
-                aclAct.fwdact_ext = FALSE;
-
-                aclAct.fwdpmask = 1 << cpuPort;
-                aclActCtrl |= FILTER_ENACT_FWD_MASK;
-                break;
-            case FILTER_ENACT_ISOLATION:
-                RTK_CHK_PORTMASK_VALID(&pFilter_action->filterPortmask);
-
-                aclAct.fwdact_ext = TRUE;
-
-                if(rtk_switch_portmask_L2P_get(&pFilter_action->filterPortmask, &portmask) != RT_ERR_OK)
-                    return RT_ERR_PORT_MASK;
-                aclAct.fwdpmask = portmask;
-
-                aclActCtrl |= FILTER_ENACT_FWD_MASK;
-                break;
-
-            case FILTER_ENACT_INTERRUPT:
-
-                aclAct.aclint = TRUE;
-                aclActCtrl |= FILTER_ENACT_INTGPIO_MASK;
-                break;
-            case FILTER_ENACT_GPO:
-
-                aclAct.gpio_en = TRUE;
-                aclAct.gpio_pin = pFilter_action->filterPin;
-                aclActCtrl |= FILTER_ENACT_INTGPIO_MASK;
-                break;
-             case FILTER_ENACT_EGRESSCTAG_TAG:
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_VLANONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_TAGONLY;
-                }
-                aclAct.tag_fmt = FILTER_CTAGFMT_TAG;
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-             case FILTER_ENACT_EGRESSCTAG_UNTAG:
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_VLANONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_TAGONLY;
-                }
-                aclAct.tag_fmt = FILTER_CTAGFMT_UNTAG;
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-             case FILTER_ENACT_EGRESSCTAG_KEEP:
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_VLANONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_TAGONLY;
-                }
-                aclAct.tag_fmt = FILTER_CTAGFMT_KEEP;
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-             case FILTER_ENACT_EGRESSCTAG_KEEPAND1PRMK:
-
-                if(aclActCtrl &(FILTER_ENACT_CVLAN_MASK))
-                {
-                    if(aclAct.cact_ext == FILTER_ENACT_CACTEXT_VLANONLY)
-                        aclAct.cact_ext = FILTER_ENACT_CACTEXT_BOTHVLANTAG;
-                }
-                else
-                {
-                    aclAct.cact_ext = FILTER_ENACT_CACTEXT_TAGONLY;
-                }
-                aclAct.tag_fmt = FILTER_CTAGFMT_KEEP1PRMK;
-                aclActCtrl |= FILTER_ENACT_CVLAN_MASK;
-                break;
-           default:
-                return RT_ERR_FILTER_INACL_ACT_NOT_SUPPORT;
-            }
-        }
-    }
-
-
-    /*check if free ACL rules are enough*/
-    for(i = filter_id; i < (filter_id + noRulesAdd); i++)
-    {
-        if((retVal = rtl8367c_getAsicAclRule(i, &tempRule)) != RT_ERR_OK )
-            return retVal;
-
-        if(tempRule.valid == TRUE)
-        {
-            return RT_ERR_TBL_FULL;
-        }
-    }
-
-    ruleId = 0;
-    for(i = 0; i < RTL8367C_ACLTEMPLATENO; i++)
-    {
-        if(aclRule[i].valid == TRUE)
-        {
-            /* write ACL action control */
-            if((retVal = rtl8367c_setAsicAclActCtrl(filter_id + ruleId, aclActCtrl)) != RT_ERR_OK )
-                return retVal;
-            /* write ACL action */
-            if((retVal = rtl8367c_setAsicAclAct(filter_id + ruleId, &aclAct)) != RT_ERR_OK )
-                return retVal;
-
-            /* write ACL not */
-            if((retVal = rtl8367c_setAsicAclNot(filter_id + ruleId, pFilter_cfg->invert)) != RT_ERR_OK )
-                return retVal;
-            /* write ACL rule */
-            if((retVal = rtl8367c_setAsicAclRule(filter_id + ruleId, &aclRule[i])) != RT_ERR_OK )
-                return retVal;
-
-            /* only the first rule will be written with input action control, aclActCtrl of other rules will be zero */
-            aclActCtrl = 0;
-            memset(&aclAct, 0, sizeof(rtl8367c_acl_act_t));
-
-            ruleId ++;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_del
- * Description:
- *      Delete an ACL configuration from ASIC
- * Input:
- *      filter_id   - Start index of ACL configuration.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_ENTRYIDX  - Invalid filter_id.
- * Note:
- *      This function delete a group of ACL rules starting from filter_id.
- */
-rtk_api_ret_t rtk_filter_igrAcl_cfg_del(rtk_filter_id_t filter_id)
-{
-    rtl8367c_aclrule initRule;
-    rtl8367c_acl_act_t  initAct;
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(filter_id > RTL8367C_ACLRULEMAX )
-        return RT_ERR_FILTER_ENTRYIDX;
-
-    memset(&initRule, 0, sizeof(rtl8367c_aclrule));
-    memset(&initAct, 0, sizeof(rtl8367c_acl_act_t));
-
-    if((ret = rtl8367c_setAsicAclRule(filter_id, &initRule)) != RT_ERR_OK)
-        return ret;
-    if((ret = rtl8367c_setAsicAclActCtrl(filter_id, FILTER_ENACT_INIT_MASK))!= RT_ERR_OK)
-        return ret;
-    if((ret = rtl8367c_setAsicAclAct(filter_id, &initAct)) != RT_ERR_OK)
-        return ret;
-    if((ret = rtl8367c_setAsicAclNot(filter_id, DISABLED)) != RT_ERR_OK )
-        return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_delAll
- * Description:
- *      Delete all ACL entries from ASIC
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      This function delete all ACL configuration from ASIC.
- */
-rtk_api_ret_t rtk_filter_igrAcl_cfg_delAll(void)
-{
-    rtk_uint32            i;
-    rtk_api_ret_t     ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    for(i = 0; i < RTL8367C_ACLRULENO; i++)
-    {
-        if((ret = rtl8367c_setAsicAclActCtrl(i, FILTER_ENACT_INIT_MASK))!= RT_ERR_OK)
-            return ret;
-        if((ret = rtl8367c_setAsicAclNot(i, DISABLED)) != RT_ERR_OK )
-            return ret;
-    }
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_ACL_RESET_CFG, RTL8367C_ACL_RESET_CFG_OFFSET, TRUE);;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_get
- * Description:
- *      Get one ingress acl configuration from ASIC.
- * Input:
- *      filter_id       - Start index of ACL configuration.
- * Output:
- *      pFilter_cfg     - buffer pointer of ingress acl data
- *      pFilter_action  - buffer pointer of ingress acl action
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Pointer pFilter_action or pFilter_cfg point to NULL.
- *      RT_ERR_FILTER_ENTRYIDX  - Invalid entry index.
- * Note:
- *      This function get configuration from ASIC.
- */
-rtk_api_ret_t rtk_filter_igrAcl_cfg_get(rtk_filter_id_t filter_id, rtk_filter_cfg_raw_t *pFilter_cfg, rtk_filter_action_t *pAction)
-{
-    rtk_api_ret_t               retVal;
-    rtk_uint32                  i, tmp;
-    rtl8367c_aclrule            aclRule;
-    rtl8367c_acl_act_t          aclAct;
-    rtk_uint32                  cpuPort;
-    rtl8367c_acltemplate_t      type;
-    rtl8367c_svlan_memconf_t    svlan_cfg;
-    rtl8367c_vlanconfiguser     vlanMC;
-    rtk_uint32                  phyPmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pFilter_cfg || NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    if(filter_id > RTL8367C_ACLRULEMAX)
-        return RT_ERR_ENTRY_INDEX;
-
-    if ((retVal = rtl8367c_getAsicAclRule(filter_id, &aclRule)) != RT_ERR_OK)
-        return retVal;
-
-    /* Check valid */
-    if(aclRule.valid == 0)
-    {
-        pFilter_cfg->valid = DISABLED;
-        return RT_ERR_OK;
-    }
-
-    phyPmask = aclRule.data_bits.active_portmsk;
-    if(rtk_switch_portmask_P2L_get(phyPmask,&(pFilter_cfg->activeport.value)) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    phyPmask = aclRule.care_bits.active_portmsk;
-    if(rtk_switch_portmask_P2L_get(phyPmask,&(pFilter_cfg->activeport.mask)) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    for(i = 0; i <= CARE_TAG_IPV6; i++)
-    {
-        if(aclRule.data_bits.tag_exist & (1 << i))
-            pFilter_cfg->careTag.tagType[i].value = 1;
-        else
-            pFilter_cfg->careTag.tagType[i].value = 0;
-
-        if (aclRule.care_bits.tag_exist & (1 << i))
-            pFilter_cfg->careTag.tagType[i].mask = 1;
-        else
-            pFilter_cfg->careTag.tagType[i].mask = 0;
-    }
-
-    if(filter_advanceCaretagField[aclRule.data_bits.type][0] == TRUE)
-    {
-        /* Advanced Care tag setting */
-        for(i = CARE_TAG_TCP; i < CARE_TAG_END; i++)
-        {
-            if(aclRule.data_bits.field[filter_advanceCaretagField[aclRule.data_bits.type][1]] & (0x0001 << (i-CARE_TAG_TCP)) )
-                pFilter_cfg->careTag.tagType[i].value = 1;
-            else
-                pFilter_cfg->careTag.tagType[i].value = 0;
-
-            if(aclRule.care_bits.field[filter_advanceCaretagField[aclRule.care_bits.type][1]] & (0x0001 << (i-CARE_TAG_TCP)) )
-                pFilter_cfg->careTag.tagType[i].mask = 1;
-            else
-                pFilter_cfg->careTag.tagType[i].mask = 0;
-        }
-    }
-
-    for(i = 0; i < RTL8367C_ACLRULEFIELDNO; i++)
-    {
-        pFilter_cfg->careFieldRaw[i] = aclRule.care_bits.field[i];
-        pFilter_cfg->dataFieldRaw[i] = aclRule.data_bits.field[i];
-    }
-
-    if ((retVal = rtl8367c_getAsicAclNot(filter_id, &tmp))!= RT_ERR_OK)
-        return retVal;
-
-    pFilter_cfg->invert = tmp;
-
-    pFilter_cfg->valid = aclRule.valid;
-
-    memset(pAction, 0, sizeof(rtk_filter_action_t));
-
-    if ((retVal = rtl8367c_getAsicAclActCtrl(filter_id, &tmp))!= RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicAclAct(filter_id, &aclAct)) != RT_ERR_OK)
-        return retVal;
-
-    if(tmp & FILTER_ENACT_FWD_MASK)
-    {
-        if(TRUE == aclAct.fwdact_ext)
-        {
-            pAction->actEnable[FILTER_ENACT_ISOLATION] = TRUE;
-
-            phyPmask = aclAct.fwdpmask;
-            if(rtk_switch_portmask_P2L_get(phyPmask,&(pAction->filterPortmask)) != RT_ERR_OK)
-                return RT_ERR_FAILED;
-        }
-        else if(aclAct.fwdact == RTL8367C_ACL_FWD_TRAP)
-        {
-            pAction->actEnable[FILTER_ENACT_TRAP_CPU] = TRUE;
-        }
-        else if (aclAct.fwdact == RTL8367C_ACL_FWD_MIRRORFUNTION )
-        {
-            pAction->actEnable[FILTER_ENACT_MIRROR] = TRUE;
-
-            phyPmask = aclAct.fwdpmask;
-            if(rtk_switch_portmask_P2L_get(phyPmask,&(pAction->filterPortmask)) != RT_ERR_OK)
-                return RT_ERR_FAILED;
-        }
-        else if (aclAct.fwdact == RTL8367C_ACL_FWD_REDIRECT)
-        {
-            if(aclAct.fwdpmask == 0 )
-                pAction->actEnable[FILTER_ENACT_DROP] = TRUE;
-            else
-            {
-                pAction->actEnable[FILTER_ENACT_REDIRECT] = TRUE;
-
-                phyPmask = aclAct.fwdpmask;
-                if(rtk_switch_portmask_P2L_get(phyPmask,&(pAction->filterPortmask)) != RT_ERR_OK)
-                    return RT_ERR_FAILED;
-            }
-        }
-        else if (aclAct.fwdact == RTL8367C_ACL_FWD_MIRROR)
-        {
-            if((retVal = rtl8367c_getAsicCputagTrapPort(&cpuPort)) != RT_ERR_OK)
-                return retVal;
-            if (aclAct.fwdpmask == (1 << cpuPort))
-            {
-                pAction->actEnable[FILTER_ENACT_COPY_CPU] = TRUE;
-            }
-            else
-            {
-                pAction->actEnable[FILTER_ENACT_ADD_DSTPORT] = TRUE;
-
-                phyPmask = aclAct.fwdpmask;
-                if(rtk_switch_portmask_P2L_get(phyPmask,&(pAction->filterPortmask)) != RT_ERR_OK)
-                    return RT_ERR_FAILED;
-            }
-        }
-        else
-        {
-            return RT_ERR_FAILED;
-        }
-    }
-
-    if(tmp & FILTER_ENACT_POLICING_MASK)
-    {
-        pAction->actEnable[FILTER_ENACT_POLICING_0] = TRUE;
-        pAction->filterPolicingIdx[0] = aclAct.aclmeteridx;
-    }
-
-    if(tmp & FILTER_ENACT_PRIORITY_MASK)
-    {
-        if(aclAct.priact == FILTER_ENACT_PRI_TYPE(FILTER_ENACT_PRIORITY))
-        {
-            pAction->actEnable[FILTER_ENACT_PRIORITY] = TRUE;
-            pAction->filterPriority = aclAct.pridx;
-        }
-        else if(aclAct.priact == FILTER_ENACT_PRI_TYPE(FILTER_ENACT_1P_REMARK))
-        {
-            pAction->actEnable[FILTER_ENACT_1P_REMARK] = TRUE;
-            pAction->filterPriority = aclAct.pridx;
-        }
-        else if(aclAct.priact == FILTER_ENACT_PRI_TYPE(FILTER_ENACT_DSCP_REMARK))
-        {
-            pAction->actEnable[FILTER_ENACT_DSCP_REMARK] = TRUE;
-            pAction->filterPriority = aclAct.pridx;
-        }
-        else if(aclAct.priact == FILTER_ENACT_PRI_TYPE(FILTER_ENACT_POLICING_3))
-        {
-            pAction->actEnable[FILTER_ENACT_POLICING_3] = TRUE;
-            pAction->filterPolicingIdx[3]  = aclAct.pridx;
-        }
-    }
-
-    if(tmp & FILTER_ENACT_SVLAN_MASK)
-    {
-        if(aclAct.sact == FILTER_ENACT_SVLAN_TYPE(FILTER_ENACT_SVLAN_INGRESS))
-        {
-            if((retVal = rtl8367c_getAsicSvlanMemberConfiguration(aclAct.svidx_sact, &svlan_cfg)) != RT_ERR_OK)
-                return retVal;
-
-            pAction->actEnable[FILTER_ENACT_SVLAN_INGRESS] = TRUE;
-            pAction->filterSvlanIdx = aclAct.svidx_sact;
-            pAction->filterSvlanVid = svlan_cfg.vs_svid;
-        }
-        else if(aclAct.sact == FILTER_ENACT_SVLAN_TYPE(FILTER_ENACT_SVLAN_EGRESS))
-        {
-            if((retVal = rtl8367c_getAsicSvlanMemberConfiguration(aclAct.svidx_sact, &svlan_cfg)) != RT_ERR_OK)
-                return retVal;
-
-            pAction->actEnable[FILTER_ENACT_SVLAN_EGRESS] = TRUE;
-            pAction->filterSvlanIdx = aclAct.svidx_sact;
-            pAction->filterSvlanVid = svlan_cfg.vs_svid;
-        }
-        else if(aclAct.sact == FILTER_ENACT_SVLAN_TYPE(FILTER_ENACT_SVLAN_CVID))
-            pAction->actEnable[FILTER_ENACT_SVLAN_CVID] = TRUE;
-        else if(aclAct.sact == FILTER_ENACT_SVLAN_TYPE(FILTER_ENACT_POLICING_2))
-        {
-            pAction->actEnable[FILTER_ENACT_POLICING_2] = TRUE;
-            pAction->filterPolicingIdx[2]  = aclAct.svidx_sact;
-        }
-    }
-
-
-    if(tmp & FILTER_ENACT_CVLAN_MASK)
-    {
-        if(FILTER_ENACT_CACTEXT_TAGONLY == aclAct.cact_ext ||
-            FILTER_ENACT_CACTEXT_BOTHVLANTAG == aclAct.cact_ext )
-        {
-            if(FILTER_CTAGFMT_UNTAG == aclAct.tag_fmt)
-            {
-                pAction->actEnable[FILTER_ENACT_EGRESSCTAG_UNTAG] = TRUE;
-            }
-            else if(FILTER_CTAGFMT_TAG == aclAct.tag_fmt)
-            {
-                pAction->actEnable[FILTER_ENACT_EGRESSCTAG_TAG] = TRUE;
-            }
-            else if(FILTER_CTAGFMT_KEEP == aclAct.tag_fmt)
-            {
-                pAction->actEnable[FILTER_ENACT_EGRESSCTAG_KEEP] = TRUE;
-            }
-             else if(FILTER_CTAGFMT_KEEP1PRMK== aclAct.tag_fmt)
-            {
-                pAction->actEnable[FILTER_ENACT_EGRESSCTAG_KEEPAND1PRMK] = TRUE;
-            }
-
-        }
-
-        if(FILTER_ENACT_CACTEXT_VLANONLY == aclAct.cact_ext ||
-            FILTER_ENACT_CACTEXT_BOTHVLANTAG == aclAct.cact_ext )
-        {
-            if(aclAct.cact == FILTER_ENACT_CVLAN_TYPE(FILTER_ENACT_CVLAN_INGRESS))
-            {
-                if((retVal = rtl8367c_getAsicVlanMemberConfig(aclAct.cvidx_cact, &vlanMC)) != RT_ERR_OK)
-                    return retVal;
-
-                pAction->actEnable[FILTER_ENACT_CVLAN_INGRESS] = TRUE;
-                pAction->filterCvlanIdx  = aclAct.cvidx_cact;
-                pAction->filterCvlanVid  = vlanMC.evid;
-            }
-            else if(aclAct.cact == FILTER_ENACT_CVLAN_TYPE(FILTER_ENACT_CVLAN_EGRESS))
-            {
-                if((retVal = rtl8367c_getAsicVlanMemberConfig(aclAct.cvidx_cact, &vlanMC)) != RT_ERR_OK)
-                    return retVal;
-
-                pAction->actEnable[FILTER_ENACT_CVLAN_EGRESS] = TRUE;
-                pAction->filterCvlanIdx  = aclAct.cvidx_cact;
-                pAction->filterCvlanVid  = vlanMC.evid;
-            }
-            else if(aclAct.cact == FILTER_ENACT_CVLAN_TYPE(FILTER_ENACT_CVLAN_SVID))
-            {
-                pAction->actEnable[FILTER_ENACT_CVLAN_SVID] = TRUE;
-            }
-            else if(aclAct.cact == FILTER_ENACT_CVLAN_TYPE(FILTER_ENACT_POLICING_1))
-            {
-                pAction->actEnable[FILTER_ENACT_POLICING_1] = TRUE;
-                pAction->filterPolicingIdx[1]  = aclAct.cvidx_cact;
-            }
-        }
-    }
-
-    if(tmp & FILTER_ENACT_INTGPIO_MASK)
-    {
-        if(TRUE == aclAct.aclint)
-        {
-            pAction->actEnable[FILTER_ENACT_INTERRUPT] = TRUE;
-        }
-
-        if(TRUE == aclAct.gpio_en)
-        {
-            pAction->actEnable[FILTER_ENACT_GPO] = TRUE;
-            pAction->filterPin = aclAct.gpio_pin;
-        }
-    }
-
-    /* Get field type of RAW data */
-    if ((retVal = rtl8367c_getAsicAclTemplate(aclRule.data_bits.type, &type))!= RT_ERR_OK)
-        return retVal;
-
-    for(i = 0; i < RTL8367C_ACLRULEFIELDNO; i++)
-    {
-        pFilter_cfg->fieldRawType[i] = type.field[i];
-    }/* end of for(i...) */
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_unmatchAction_set
- * Description:
- *      Set action to packets when no ACL configuration match
- * Input:
- *      port    - Port id.
- *      action  - Action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function sets action of packets when no ACL configruation matches.
- */
-rtk_api_ret_t rtk_filter_igrAcl_unmatchAction_set(rtk_port_t port, rtk_filter_unmatch_action_t action)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(action >= FILTER_UNMATCH_END)
-        return RT_ERR_INPUT;
-
-    if((ret = rtl8367c_setAsicAclUnmatchedPermit(rtk_switch_port_L2P_get(port), action)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_unmatchAction_get
- * Description:
- *      Get action to packets when no ACL configuration match
- * Input:
- *      port    - Port id.
- * Output:
- *      pAction - Action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function gets action of packets when no ACL configruation matches.
- */
-rtk_api_ret_t rtk_filter_igrAcl_unmatchAction_get(rtk_port_t port, rtk_filter_unmatch_action_t* pAction)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if((ret = rtl8367c_getAsicAclUnmatchedPermit(rtk_switch_port_L2P_get(port), pAction)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_state_set
- * Description:
- *      Set state of ingress ACL.
- * Input:
- *      port    - Port id.
- *      state   - Ingress ACL state.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function gets action of packets when no ACL configruation matches.
- */
-rtk_api_ret_t rtk_filter_igrAcl_state_set(rtk_port_t port, rtk_filter_state_t state)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(state >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if((ret = rtl8367c_setAsicAcl(rtk_switch_port_L2P_get(port), state)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_state_get
- * Description:
- *      Get state of ingress ACL.
- * Input:
- *      port    - Port id.
- * Output:
- *      pState  - Ingress ACL state.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function gets action of packets when no ACL configruation matches.
- */
-rtk_api_ret_t rtk_filter_igrAcl_state_get(rtk_port_t port, rtk_filter_state_t* pState)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pState)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if((ret = rtl8367c_getAsicAcl(rtk_switch_port_L2P_get(port), pState)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtk_filter_igrAcl_template_set
- * Description:
- *      Set template of ingress ACL.
- * Input:
- *      template - Ingress ACL template
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Invalid input parameters.
- * Note:
- *      This function set ACL template.
- */
-rtk_api_ret_t rtk_filter_igrAcl_template_set(rtk_filter_template_t *aclTemplate)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 idxField;
-    rtl8367c_acltemplate_t aclType;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(aclTemplate->index >= RTK_MAX_NUM_OF_FILTER_TYPE)
-        return RT_ERR_INPUT;
-
-    for(idxField = 0; idxField < RTK_MAX_NUM_OF_FILTER_FIELD; idxField++)
-    {
-        if(aclTemplate->fieldType[idxField] < FILTER_FIELD_RAW_DMAC_15_0 ||
-            (aclTemplate->fieldType[idxField] > FILTER_FIELD_RAW_CTAG && aclTemplate->fieldType[idxField] < FILTER_FIELD_RAW_IPV4_SIP_15_0 ) ||
-            (aclTemplate->fieldType[idxField] > FILTER_FIELD_RAW_IPV4_DIP_31_16 && aclTemplate->fieldType[idxField] < FILTER_FIELD_RAW_IPV6_SIP_15_0 ) ||
-            (aclTemplate->fieldType[idxField] > FILTER_FIELD_RAW_IPV6_DIP_31_16 && aclTemplate->fieldType[idxField] < FILTER_FIELD_RAW_VIDRANGE ) ||
-            (aclTemplate->fieldType[idxField] > FILTER_FIELD_RAW_FIELD_VALID && aclTemplate->fieldType[idxField] < FILTER_FIELD_RAW_FIELD_SELECT00 ) ||
-            aclTemplate->fieldType[idxField] >= FILTER_FIELD_RAW_END)
-        {
-            return RT_ERR_INPUT;
-        }
-    }
-
-    for(idxField = 0; idxField < RTK_MAX_NUM_OF_FILTER_FIELD; idxField++)
-    {
-        aclType.field[idxField] = aclTemplate->fieldType[idxField];
-    }
-
-    if((retVal = rtl8367c_setAsicAclTemplate(aclTemplate->index, &aclType)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_template_get
- * Description:
- *      Get template of ingress ACL.
- * Input:
- *      template - Ingress ACL template
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This function gets template of ACL.
- */
-rtk_api_ret_t rtk_filter_igrAcl_template_get(rtk_filter_template_t *aclTemplate)
-{
-    rtk_api_ret_t ret;
-    rtk_uint32 idxField;
-    rtl8367c_acltemplate_t aclType;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == aclTemplate)
-        return RT_ERR_NULL_POINTER;
-
-    if(aclTemplate->index >= RTK_MAX_NUM_OF_FILTER_TYPE)
-        return RT_ERR_INPUT;
-
-   if((ret = rtl8367c_getAsicAclTemplate(aclTemplate->index, &aclType)) != RT_ERR_OK)
-       return ret;
-
-    for(idxField = 0; idxField < RTK_MAX_NUM_OF_FILTER_FIELD; idxField ++)
-    {
-        aclTemplate->fieldType[idxField] = aclType.field[idxField];
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_field_sel_set
- * Description:
- *      Set user defined field selectors in HSB
- * Input:
- *      index       - index of field selector 0-15
- *      format      - Format of field selector
- *      offset      - Retrieving data offset
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      System support 16 user defined field selctors.
- *      Each selector can be enabled or disable.
- *      User can defined retrieving 16-bits in many predefiend
- *      standard l2/l3/l4 payload.
- */
-rtk_api_ret_t rtk_filter_igrAcl_field_sel_set(rtk_uint32 index, rtk_field_sel_t format, rtk_uint32 offset)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(index >= RTL8367C_FIELDSEL_FORMAT_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(format >= FORMAT_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(offset > RTL8367C_FIELDSEL_MAX_OFFSET)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((ret = rtl8367c_setAsicFieldSelector(index, (rtk_uint32)format, offset)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAcl_field_sel_get
- * Description:
- *      Get user defined field selectors in HSB
- * Input:
- *      index       - index of field selector 0-15
- * Output:
- *      pFormat     - Format of field selector
- *      pOffset     - Retrieving data offset
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_filter_igrAcl_field_sel_get(rtk_uint32 index, rtk_field_sel_t *pFormat, rtk_uint32 *pOffset)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pFormat || NULL == pOffset)
-        return RT_ERR_NULL_POINTER;
-
-    if(index >= RTL8367C_FIELDSEL_FORMAT_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((ret = rtl8367c_getAsicFieldSelector(index, pFormat, pOffset)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_iprange_set
- * Description:
- *      Set IP Range check
- * Input:
- *      index       - index of IP Range 0-15
- *      type        - IP Range check type, 0:Delete a entry, 1: IPv4_SIP, 2: IPv4_DIP, 3:IPv6_SIP, 4:IPv6_DIP
- *      upperIp     - The upper bound of IP range
- *      lowerIp     - The lower Bound of IP range
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      upperIp must be larger or equal than lowerIp.
- */
-rtk_api_ret_t rtk_filter_iprange_set(rtk_uint32 index, rtk_filter_iprange_t type, ipaddr_t upperIp, ipaddr_t lowerIp)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(type >= IPRANGE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(lowerIp > upperIp)
-        return RT_ERR_INPUT;
-
-    if((ret = rtl8367c_setAsicAclIpRange(index, type, upperIp, lowerIp)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_iprange_get
- * Description:
- *      Set IP Range check
- * Input:
- *      index       - index of IP Range 0-15
- * Output:
- *      pType        - IP Range check type, 0:Delete a entry, 1: IPv4_SIP, 2: IPv4_DIP, 3:IPv6_SIP, 4:IPv6_DIP
- *      pUpperIp     - The upper bound of IP range
- *      pLowerIp     - The lower Bound of IP range
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_filter_iprange_get(rtk_uint32 index, rtk_filter_iprange_t *pType, ipaddr_t *pUpperIp, ipaddr_t *pLowerIp)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if((NULL == pType) || (NULL == pUpperIp) || (NULL == pLowerIp))
-        return RT_ERR_NULL_POINTER;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((ret = rtl8367c_getAsicAclIpRange(index, pType, pUpperIp, pLowerIp)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_vidrange_set
- * Description:
- *      Set VID Range check
- * Input:
- *      index       - index of VID Range 0-15
- *      type        - IP Range check type, 0:Delete a entry, 1: CVID, 2: SVID
- *      upperVid    - The upper bound of VID range
- *      lowerVid    - The lower Bound of VID range
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      upperVid must be larger or equal than lowerVid.
- */
-rtk_api_ret_t rtk_filter_vidrange_set(rtk_uint32 index, rtk_filter_vidrange_t type, rtk_uint32 upperVid, rtk_uint32 lowerVid)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(type >= VIDRANGE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(lowerVid > upperVid)
-        return RT_ERR_INPUT;
-
-    if( (upperVid > RTL8367C_VIDMAX) || (lowerVid > RTL8367C_VIDMAX))
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((ret = rtl8367c_setAsicAclVidRange(index, type, upperVid, lowerVid)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_vidrange_get
- * Description:
- *      Get VID Range check
- * Input:
- *      index       - index of VID Range 0-15
- * Output:
- *      pType        - IP Range check type, 0:Unused, 1: CVID, 2: SVID
- *      pUpperVid    - The upper bound of VID range
- *      pLowerVid    - The lower Bound of VID range
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_filter_vidrange_get(rtk_uint32 index, rtk_filter_vidrange_t *pType, rtk_uint32 *pUpperVid, rtk_uint32 *pLowerVid)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if((NULL == pType) || (NULL == pUpperVid) || (NULL == pLowerVid))
-        return RT_ERR_NULL_POINTER;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((ret = rtl8367c_getAsicAclVidRange(index, pType, pUpperVid, pLowerVid)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_portrange_set
- * Description:
- *      Set Port Range check
- * Input:
- *      index       - index of Port Range 0-15
- *      type        - IP Range check type, 0:Delete a entry, 1: Source Port, 2: Destnation Port
- *      upperPort   - The upper bound of Port range
- *      lowerPort   - The lower Bound of Port range
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      upperPort must be larger or equal than lowerPort.
- */
-rtk_api_ret_t rtk_filter_portrange_set(rtk_uint32 index, rtk_filter_portrange_t type, rtk_uint32 upperPort, rtk_uint32 lowerPort)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(type >= PORTRANGE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(lowerPort > upperPort)
-        return RT_ERR_INPUT;
-
-    if(upperPort > RTL8367C_ACL_PORTRANGEMAX)
-        return RT_ERR_INPUT;
-
-    if(lowerPort > RTL8367C_ACL_PORTRANGEMAX)
-        return RT_ERR_INPUT;
-
-    if((ret = rtl8367c_setAsicAclPortRange(index, type, upperPort, lowerPort)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_portrange_get
- * Description:
- *      Set Port Range check
- * Input:
- *      index       - index of Port Range 0-15
- * Output:
- *      pType       - IP Range check type, 0:Delete a entry, 1: Source Port, 2: Destnation Port
- *      pUpperPort  - The upper bound of Port range
- *      pLowerPort  - The lower Bound of Port range
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_filter_portrange_get(rtk_uint32 index, rtk_filter_portrange_t *pType, rtk_uint32 *pUpperPort, rtk_uint32 *pLowerPort)
-{
-    rtk_api_ret_t ret;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if((NULL == pType) || (NULL == pUpperPort) || (NULL == pLowerPort))
-        return RT_ERR_NULL_POINTER;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((ret = rtl8367c_getAsicAclPortRange(index, pType, pUpperPort, pLowerPort)) != RT_ERR_OK)
-       return ret;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_filter_igrAclPolarity_set
- * Description:
- *      Set ACL Goip control palarity
- * Input:
- *      polarity - 1: High, 0: Low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      none
- */
-rtk_api_ret_t rtk_filter_igrAclPolarity_set(rtk_uint32 polarity)
-{
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(polarity > 1)
-        return RT_ERR_OUT_OF_RANGE;
-    return rtl8367c_setAsicAclGpioPolarity(polarity);
-}
-/* Function Name:
- *      rtk_filter_igrAclPolarity_get
- * Description:
- *      Get ACL Goip control palarity
- * Input:
- *      pPolarity - 1: High, 0: Low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      none
- */
-rtk_api_ret_t rtk_filter_igrAclPolarity_get(rtk_uint32* pPolarity)
-{
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPolarity)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicAclGpioPolarity(pPolarity);
-}
-
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/cpu.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/cpu.c
deleted file mode 100644
index d1cd95b37a..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/cpu.c
+++ /dev/null
@@ -1,537 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in CPU module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <cpu.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_cputag.h>
-
-/* Function Name:
- *      rtk_cpu_enable_set
- * Description:
- *      Set CPU port function enable/disable.
- * Input:
- *      enable - CPU port function enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can set CPU port function enable/disable.
- */
-rtk_api_ret_t rtk_cpu_enable_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicCputagEnable(enable)) != RT_ERR_OK)
-        return retVal;
-
-    if (DISABLED == enable)
-    {
-        if ((retVal = rtl8367c_setAsicCputagPortmask(0)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_enable_get
- * Description:
- *      Get CPU port and its setting.
- * Input:
- *      None
- * Output:
- *      pEnable - CPU port function enable
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_L2_NO_CPU_PORT   - CPU port is not exist
- * Note:
- *      The API can get CPU port function enable/disable.
- */
-rtk_api_ret_t rtk_cpu_enable_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicCputagEnable(pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_tagPort_set
- * Description:
- *      Set CPU port and CPU tag insert mode.
- * Input:
- *      port - Port id.
- *      mode - CPU tag insert for packets egress from CPU port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can set CPU port and inserting proprietary CPU tag mode (Length/Type 0x8899)
- *      to the frame that transmitting to CPU port.
- *      The inset cpu tag mode is as following:
- *      - CPU_INSERT_TO_ALL
- *      - CPU_INSERT_TO_TRAPPING
- *      - CPU_INSERT_TO_NONE
- */
-rtk_api_ret_t rtk_cpu_tagPort_set(rtk_port_t port, rtk_cpu_insert_t mode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (mode >= CPU_INSERT_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicCputagPortmask(1<<rtk_switch_port_L2P_get(port))) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicCputagTrapPort(rtk_switch_port_L2P_get(port))) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicCputagInsertMode(mode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_tagPort_get
- * Description:
- *      Get CPU port and CPU tag insert mode.
- * Input:
- *      None
- * Output:
- *      pPort - Port id.
- *      pMode - CPU tag insert for packets egress from CPU port, 0:all insert 1:Only for trapped packets 2:no insert.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_L2_NO_CPU_PORT   - CPU port is not exist
- * Note:
- *      The API can get configured CPU port and its setting.
- *      The inset cpu tag mode is as following:
- *      - CPU_INSERT_TO_ALL
- *      - CPU_INSERT_TO_TRAPPING
- *      - CPU_INSERT_TO_NONE
- */
-rtk_api_ret_t rtk_cpu_tagPort_get(rtk_port_t *pPort, rtk_cpu_insert_t *pMode)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk, port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPort)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pMode)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicCputagPortmask(&pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicCputagTrapPort(&port)) != RT_ERR_OK)
-        return retVal;
-
-    *pPort = rtk_switch_port_P2L_get(port);
-
-    if ((retVal = rtl8367c_getAsicCputagInsertMode(pMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_cpu_awarePort_set
- * Description:
- *      Set CPU aware port mask.
- * Input:
- *      portmask - Port mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK      - Invalid port mask.
- * Note:
- *      The API can set configured CPU aware port mask.
- */
-rtk_api_ret_t rtk_cpu_awarePort_set(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 phyMbrPmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Valid port mask */
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port mask valid */
-    RTK_CHK_PORTMASK_VALID(pPortmask);
-
-    if(rtk_switch_portmask_L2P_get(pPortmask, &phyMbrPmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    if ((retVal = rtl8367c_setAsicCputagPortmask(phyMbrPmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_awarePort_get
- * Description:
- *      Get CPU aware port mask.
- * Input:
- *      None
- * Output:
- *      pPortmask - Port mask.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      The API can get configured CPU aware port mask.
- */
-rtk_api_ret_t rtk_cpu_awarePort_get(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicCputagPortmask(&pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    if(rtk_switch_portmask_P2L_get(pmsk, pPortmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_tagPosition_set
- * Description:
- *      Set CPU tag position.
- * Input:
- *      position - CPU tag position.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can set CPU tag position.
- */
-rtk_api_ret_t rtk_cpu_tagPosition_set(rtk_cpu_position_t position)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (position >= CPU_POS_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicCputagPosition(position)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_tagPosition_get
- * Description:
- *      Get CPU tag position.
- * Input:
- *      None
- * Output:
- *      pPosition - CPU tag position.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can get CPU tag position.
- */
-rtk_api_ret_t rtk_cpu_tagPosition_get(rtk_cpu_position_t *pPosition)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPosition)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicCputagPosition(pPosition)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_tagLength_set
- * Description:
- *      Set CPU tag length.
- * Input:
- *      length - CPU tag length.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can set CPU tag length.
- */
-rtk_api_ret_t rtk_cpu_tagLength_set(rtk_cpu_tag_length_t length)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (length >= CPU_LEN_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicCputagMode(length)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_tagLength_get
- * Description:
- *      Get CPU tag length.
- * Input:
- *      None
- * Output:
- *      pLength - CPU tag length.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can get CPU tag length.
- */
-rtk_api_ret_t rtk_cpu_tagLength_get(rtk_cpu_tag_length_t *pLength)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pLength)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicCputagMode(pLength)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_priRemap_set
- * Description:
- *      Configure CPU priorities mapping to internal absolute priority.
- * Input:
- *      int_pri     - internal priority value.
- *      new_pri    - new internal priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of CPU tag assignment for internal asic priority, and it is used for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_cpu_priRemap_set(rtk_pri_t int_pri, rtk_pri_t new_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (new_pri > RTL8367C_PRIMAX || int_pri > RTL8367C_PRIMAX)
-        return  RT_ERR_VLAN_PRIORITY;
-
-    if ((retVal = rtl8367c_setAsicCputagPriorityRemapping(int_pri, new_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_priRemap_get
- * Description:
- *      Configure CPU priorities mapping to internal absolute priority.
- * Input:
- *      int_pri     - internal priority value.
- * Output:
- *      pNew_pri    - new internal priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of CPU tag assignment for internal asic priority, and it is used for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_cpu_priRemap_get(rtk_pri_t int_pri, rtk_pri_t *pNew_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pNew_pri)
-        return RT_ERR_NULL_POINTER;
-
-    if (int_pri > RTL8367C_PRIMAX)
-        return  RT_ERR_QOS_INT_PRIORITY;
-
-    if ((retVal = rtl8367c_getAsicCputagPriorityRemapping(int_pri, pNew_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_acceptLength_set
- * Description:
- *      Set CPU accept  length.
- * Input:
- *      length - CPU tag length.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can set CPU accept length.
- */
-rtk_api_ret_t rtk_cpu_acceptLength_set(rtk_cpu_rx_length_t length)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (length >= CPU_RX_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicCputagRxMinLength(length)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_cpu_acceptLength_get
- * Description:
- *      Get CPU accept length.
- * Input:
- *      None
- * Output:
- *      pLength - CPU tag length.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can get CPU accept length.
- */
-rtk_api_ret_t rtk_cpu_acceptLength_get(rtk_cpu_rx_length_t *pLength)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pLength)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicCputagRxMinLength(pLength)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/dot1x.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/dot1x.c
deleted file mode 100644
index c9b146a6d8..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/dot1x.c
+++ /dev/null
@@ -1,843 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 75783 $
- * $Date: 2017-02-13 14:54:53 +0800 (週一, 13 二月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in 1X module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <dot1x.h>
-#include <string.h>
-#include <vlan.h>
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_dot1x.h>
-#include <rtl8367c_asicdrv_rma.h>
-#include <rtl8367c_asicdrv_lut.h>
-#include <rtl8367c_asicdrv_vlan.h>
-
-/* Function Name:
- *      rtk_dot1x_unauthPacketOper_set
- * Description:
- *      Set 802.1x unauth action configuration.
- * Input:
- *      port            - Port id.
- *      unauth_action   - 802.1X unauth action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      This API can set 802.1x unauth action configuration.
- *      The unauth action is as following:
- *      - DOT1X_ACTION_DROP
- *      - DOT1X_ACTION_TRAP2CPU
- *      - DOT1X_ACTION_GUESTVLAN
- */
-rtk_api_ret_t rtk_dot1x_unauthPacketOper_set(rtk_port_t port, rtk_dot1x_unauth_action_t unauth_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (unauth_action >= DOT1X_ACTION_END)
-        return RT_ERR_DOT1X_PROC;
-
-    if ((retVal = rtl8367c_setAsic1xProcConfig(rtk_switch_port_L2P_get(port), unauth_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_unauthPacketOper_get
- * Description:
- *      Get 802.1x unauth action configuration.
- * Input:
- *      port - Port id.
- * Output:
- *      pUnauth_action - 802.1X unauth action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get 802.1x unauth action configuration.
- *      The unauth action is as following:
- *      - DOT1X_ACTION_DROP
- *      - DOT1X_ACTION_TRAP2CPU
- *      - DOT1X_ACTION_GUESTVLAN
- */
-rtk_api_ret_t rtk_dot1x_unauthPacketOper_get(rtk_port_t port, rtk_dot1x_unauth_action_t *pUnauth_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pUnauth_action)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsic1xProcConfig(rtk_switch_port_L2P_get(port), pUnauth_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_eapolFrame2CpuEnable_set
- * Description:
- *      Set 802.1x EAPOL packet trap to CPU configuration
- * Input:
- *      enable - The status of 802.1x EAPOL packet.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      To support 802.1x authentication functionality, EAPOL frame (ether type = 0x888E) has to
- *      be trapped to CPU.
- *      The status of EAPOL frame trap to CPU is as following:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_dot1x_eapolFrame2CpuEnable_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_getAsicRma(3, &rmacfg)) != RT_ERR_OK)
-        return retVal;
-
-    if (ENABLED == enable)
-        rmacfg.operation = RMAOP_TRAP_TO_CPU;
-    else if (DISABLED == enable)
-        rmacfg.operation = RMAOP_FORWARD;
-
-    if ((retVal = rtl8367c_setAsicRma(3, &rmacfg)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_eapolFrame2CpuEnable_get
- * Description:
- *      Get 802.1x EAPOL packet trap to CPU configuration
- * Input:
- *      None
- * Output:
- *      pEnable - The status of 802.1x EAPOL packet.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      To support 802.1x authentication functionality, EAPOL frame (ether type = 0x888E) has to
- *      be trapped to CPU.
- *      The status of EAPOL frame trap to CPU is as following:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_dot1x_eapolFrame2CpuEnable_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicRma(3, &rmacfg)) != RT_ERR_OK)
-        return retVal;
-
-    if (RMAOP_TRAP_TO_CPU == rmacfg.operation)
-        *pEnable = ENABLED;
-    else
-        *pEnable = DISABLED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_portBasedEnable_set
- * Description:
- *      Set 802.1x port-based enable configuration
- * Input:
- *      port - Port id.
- *      enable - The status of 802.1x port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_ENABLE               - Invalid enable input.
- *      RT_ERR_DOT1X_PORTBASEDPNEN  - 802.1X port-based enable error
- * Note:
- *      The API can update the port-based port enable register content. If a port is 802.1x
- *      port based network access control "enabled", it should be authenticated so packets
- *      from that port won't be dropped or trapped to CPU.
- *      The status of 802.1x port-based network access control is as following:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_dot1x_portBasedEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsic1xPBEnConfig(rtk_switch_port_L2P_get(port),enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_portBasedEnable_get
- * Description:
- *      Get 802.1x port-based enable configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - The status of 802.1x port.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get the 802.1x port-based port status.
- */
-rtk_api_ret_t rtk_dot1x_portBasedEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsic1xPBEnConfig(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_portBasedAuthStatus_set
- * Description:
- *      Set 802.1x port-based auth. port configuration
- * Input:
- *      port - Port id.
- *      port_auth - The status of 802.1x port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *     RT_ERR_DOT1X_PORTBASEDAUTH   - 802.1X port-based auth error
- * Note:
- *      The authenticated status of 802.1x port-based network access control is as following:
- *      - UNAUTH
- *      - AUTH
- */
-rtk_api_ret_t rtk_dot1x_portBasedAuthStatus_set(rtk_port_t port, rtk_dot1x_auth_status_t port_auth)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-     if (port_auth >= AUTH_STATUS_END)
-        return RT_ERR_DOT1X_PORTBASEDAUTH;
-
-    if ((retVal = rtl8367c_setAsic1xPBAuthConfig(rtk_switch_port_L2P_get(port), port_auth)) != RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_portBasedAuthStatus_get
- * Description:
- *      Get 802.1x port-based auth. port configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pPort_auth - The status of 802.1x port.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get 802.1x port-based port auth.information.
- */
-rtk_api_ret_t rtk_dot1x_portBasedAuthStatus_get(rtk_port_t port, rtk_dot1x_auth_status_t *pPort_auth)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPort_auth)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsic1xPBAuthConfig(rtk_switch_port_L2P_get(port), pPort_auth)) != RT_ERR_OK)
-        return retVal;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_portBasedDirection_set
- * Description:
- *      Set 802.1x port-based operational direction configuration
- * Input:
- *      port            - Port id.
- *      port_direction  - Operation direction
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_DOT1X_PORTBASEDOPDIR - 802.1X port-based operation direction error
- * Note:
- *      The operate controlled direction of 802.1x port-based network access control is as following:
- *      - BOTH
- *      - IN
- */
-rtk_api_ret_t rtk_dot1x_portBasedDirection_set(rtk_port_t port, rtk_dot1x_direction_t port_direction)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (port_direction >= DIRECTION_END)
-        return RT_ERR_DOT1X_PORTBASEDOPDIR;
-
-    if ((retVal = rtl8367c_setAsic1xPBOpdirConfig(rtk_switch_port_L2P_get(port), port_direction)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_portBasedDirection_get
- * Description:
- *      Get 802.1X port-based operational direction configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pPort_direction - Operation direction
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get 802.1x port-based operational direction information.
- */
-rtk_api_ret_t rtk_dot1x_portBasedDirection_get(rtk_port_t port, rtk_dot1x_direction_t *pPort_direction)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPort_direction)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsic1xPBOpdirConfig(rtk_switch_port_L2P_get(port), pPort_direction)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_macBasedEnable_set
- * Description:
- *      Set 802.1x mac-based port enable configuration
- * Input:
- *      port - Port id.
- *      enable - The status of 802.1x port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_ENABLE               - Invalid enable input.
- *      RT_ERR_DOT1X_MACBASEDPNEN   - 802.1X mac-based enable error
- * Note:
- *      If a port is 802.1x MAC based network access control "enabled", the incoming packets should
- *       be authenticated so packets from that port won't be dropped or trapped to CPU.
- *      The status of 802.1x MAC-based network access control is as following:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_dot1x_macBasedEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsic1xMBEnConfig(rtk_switch_port_L2P_get(port),enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_macBasedEnable_get
- * Description:
- *      Get 802.1x mac-based port enable configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - The status of 802.1x port.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      If a port is 802.1x MAC based network access control "enabled", the incoming packets should
- *      be authenticated so packets from that port wont be dropped or trapped to CPU.
- *      The status of 802.1x MAC-based network access control is as following:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_dot1x_macBasedEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsic1xMBEnConfig(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_macBasedAuthMac_add
- * Description:
- *      Add an authenticated MAC to ASIC
- * Input:
- *      port        - Port id.
- *      pAuth_mac   - The authenticated MAC.
- *      fid         - filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_ENABLE               - Invalid enable input.
- *      RT_ERR_DOT1X_MACBASEDPNEN   - 802.1X mac-based enable error
- * Note:
- *      The API can add a 802.1x authenticated MAC address to port. If the MAC does not exist in LUT,
- *      user can't add this MAC to auth status.
- */
-rtk_api_ret_t rtk_dot1x_macBasedAuthMac_add(rtk_port_t port, rtk_mac_t *pAuth_mac, rtk_fid_t fid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* must be unicast address */
-    if ((pAuth_mac == NULL) || (pAuth_mac->octet[0] & 0x1))
-        return RT_ERR_MAC;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (fid > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-
-    /* fill key (MAC,FID) to get L2 entry */
-    memcpy(l2Table.mac.octet, pAuth_mac->octet, ETHER_ADDR_LEN);
-    l2Table.fid = fid;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if ( RT_ERR_OK == retVal)
-    {
-        if (l2Table.spa != rtk_switch_port_L2P_get(port))
-            return RT_ERR_DOT1X_MAC_PORT_MISMATCH;
-
-        memcpy(l2Table.mac.octet, pAuth_mac->octet, ETHER_ADDR_LEN);
-        l2Table.fid = fid;
-        l2Table.efid = 0;
-        l2Table.auth = 1;
-        retVal = rtl8367c_setAsicL2LookupTb(&l2Table);
-        return retVal;
-    }
-    else
-        return retVal;
-
-}
-
-/* Function Name:
- *      rtk_dot1x_macBasedAuthMac_del
- * Description:
- *      Delete an authenticated MAC to ASIC
- * Input:
- *      port - Port id.
- *      pAuth_mac - The authenticated MAC.
- *      fid - filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_MAC          - Invalid MAC address.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can delete a 802.1x authenticated MAC address to port. It only change the auth status of
- *      the MAC and won't delete it from LUT.
- */
-rtk_api_ret_t rtk_dot1x_macBasedAuthMac_del(rtk_port_t port, rtk_mac_t *pAuth_mac, rtk_fid_t fid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* must be unicast address */
-    if ((pAuth_mac == NULL) || (pAuth_mac->octet[0] & 0x1))
-        return RT_ERR_MAC;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (fid > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-
-    /* fill key (MAC,FID) to get L2 entry */
-    memcpy(l2Table.mac.octet, pAuth_mac->octet, ETHER_ADDR_LEN);
-    l2Table.fid = fid;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal)
-    {
-        if (l2Table.spa != rtk_switch_port_L2P_get(port))
-            return RT_ERR_DOT1X_MAC_PORT_MISMATCH;
-
-        memcpy(l2Table.mac.octet, pAuth_mac->octet, ETHER_ADDR_LEN);
-        l2Table.fid = fid;
-        l2Table.auth = 0;
-        retVal = rtl8367c_setAsicL2LookupTb(&l2Table);
-        return retVal;
-    }
-    else
-        return retVal;
-
-}
-
-/* Function Name:
- *      rtk_dot1x_macBasedDirection_set
- * Description:
- *      Set 802.1x mac-based operational direction configuration
- * Input:
- *      mac_direction - Operation direction
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter.
- *      RT_ERR_DOT1X_MACBASEDOPDIR  - 802.1X mac-based operation direction error
- * Note:
- *      The operate controlled direction of 802.1x mac-based network access control is as following:
- *      - BOTH
- *      - IN
- */
-rtk_api_ret_t rtk_dot1x_macBasedDirection_set(rtk_dot1x_direction_t mac_direction)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (mac_direction >= DIRECTION_END)
-        return RT_ERR_DOT1X_MACBASEDOPDIR;
-
-    if ((retVal = rtl8367c_setAsic1xMBOpdirConfig(mac_direction)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_macBasedDirection_get
- * Description:
- *      Get 802.1x mac-based operational direction configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pMac_direction - Operation direction
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get 802.1x mac-based operational direction information.
- */
-rtk_api_ret_t rtk_dot1x_macBasedDirection_get(rtk_dot1x_direction_t *pMac_direction)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMac_direction)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsic1xMBOpdirConfig(pMac_direction)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      Set 802.1x guest VLAN configuration
- * Description:
- *      Set 802.1x mac-based operational direction configuration
- * Input:
- *      vid - 802.1x guest VLAN ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The operate controlled 802.1x guest VLAN
- */
-rtk_api_ret_t rtk_dot1x_guestVlan_set(rtk_vlan_t vid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 index;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* vid must be 0~4095 */
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    if((retVal = rtk_vlan_checkAndCreateMbr(vid, &index)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsic1xGuestVidx(index)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_guestVlan_get
- * Description:
- *      Get 802.1x guest VLAN configuration
- * Input:
- *      None
- * Output:
- *      pVid - 802.1x guest VLAN ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get 802.1x guest VLAN information.
- */
-rtk_api_ret_t rtk_dot1x_guestVlan_get(rtk_vlan_t *pVid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 gvidx;
-    rtl8367c_vlanconfiguser vlanMC;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pVid)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsic1xGuestVidx(&gvidx)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicVlanMemberConfig(gvidx, &vlanMC)) != RT_ERR_OK)
-        return retVal;
-
-    *pVid = vlanMC.evid;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_guestVlan2Auth_set
- * Description:
- *      Set 802.1x guest VLAN to auth host configuration
- * Input:
- *      enable - The status of guest VLAN to auth host.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The operational direction of 802.1x guest VLAN to auth host control is as following:
- *      - ENABLED
- *      - DISABLED
- */
-rtk_api_ret_t rtk_dot1x_guestVlan2Auth_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsic1xGVOpdir(enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_dot1x_guestVlan2Auth_get
- * Description:
- *      Get 802.1x guest VLAN to auth host configuration
- * Input:
- *      None
- * Output:
- *      pEnable - The status of guest VLAN to auth host.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get 802.1x guest VLAN to auth host information.
- */
-rtk_api_ret_t rtk_dot1x_guestVlan2Auth_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsic1xGVOpdir(pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/eee.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/eee.c
deleted file mode 100644
index cd14c2ce13..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/eee.c
+++ /dev/null
@@ -1,162 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 48156 $
- * $Date: 2014-05-29 16:39:06 +0800 (週四, 29 五月 2014) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in EEE module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <eee.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_eee.h>
-#include <rtl8367c_asicdrv_phy.h>
-
-/* Function Name:
- *      rtk_eee_init
- * Description:
- *      EEE function initialization.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API is used to initialize EEE status.
- */
-rtk_api_ret_t rtk_eee_init(void)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if((retVal = rtl8367c_setAsicRegBit(0x0018, 10, 1)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(0x0018, 11, 1)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_eee_portEnable_set
- * Description:
- *      Set enable status of EEE function.
- * Input:
- *      port - port id.
- *      enable - enable EEE status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_ID - Invalid port number.
- *      RT_ERR_ENABLE - Invalid enable input.
- * Note:
- *      This API can set EEE function to the specific port.
- *      The configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-rtk_api_ret_t rtk_eee_portEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-    rtk_uint32    phy_port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port is UTP port */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if (enable>=RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    phy_port = rtk_switch_port_L2P_get(port);
-
-    if ((retVal = rtl8367c_setAsicEee100M(phy_port,enable))!=RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicEeeGiga(phy_port,enable))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPHYReg(phy_port, RTL8367C_PHY_PAGE_ADDRESS, 0))!=RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_getAsicPHYReg(phy_port, 0, &regData))!=RT_ERR_OK)
-        return retVal;
-    regData |= 0x0200;
-    if ((retVal = rtl8367c_setAsicPHYReg(phy_port, 0, regData))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_eee_portEnable_get
- * Description:
- *      Get enable status of EEE function
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Back pressure status.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_ID - Invalid port number.
- * Note:
- *      This API can get EEE function to the specific port.
- *      The configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-
-rtk_api_ret_t rtk_eee_portEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData1, regData2;
-    rtk_uint32    phy_port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port is UTP port */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    phy_port = rtk_switch_port_L2P_get(port);
-
-    if ((retVal = rtl8367c_getAsicEee100M(phy_port,&regData1))!=RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_getAsicEeeGiga(phy_port,&regData2))!=RT_ERR_OK)
-        return retVal;
-
-    if (regData1==1&&regData2==1)
-        *pEnable = ENABLED;
-    else
-        *pEnable = DISABLED;
-
-    return RT_ERR_OK;
-}
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/i2c.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/i2c.c
deleted file mode 100644
index 17a5f3785b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/i2c.c
+++ /dev/null
@@ -1,436 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 63932 $
- * $Date: 2015-12-08 14:06:29 +0800 (周二, 08 �二月 2015) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in i2c module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <port.h>
-#include <string.h>
-#include <rtl8367c_reg.h>
-
-#include <rtl8367c_asicdrv_i2c.h>
-#include <rtk_switch.h>
-#include <rtl8367c_asicdrv.h>
-#include <rtk_types.h>
-#include <i2c.h>
-
-
-static rtk_I2C_16bit_mode_t rtk_i2c_mode = I2C_LSB_16BIT_MODE;
-
-
-/* Function Name:
- *      rtk_i2c_init
- * Description:
- *      I2C smart function initialization.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- * Note:
- *      This API is used to initialize EEE status.
- *      need used GPIO pins
- *      OpenDrain and clock
- */
-rtk_api_ret_t rtk_i2c_init(void)
-{
-    rtk_uint32 retVal;
-  switch_chip_t ChipID;
-  /* probe switch */
-  if((retVal = rtk_switch_probe(&ChipID)) != RT_ERR_OK)
-      return retVal;
-
-  if( ChipID == CHIP_RTL8370B )
-  {
-   /*set GPIO8, GPIO9, OpenDrain as I2C, clock = 252KHZ   */
-      if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_SYS_CTL, 0x5c3f)) != RT_ERR_OK)
-        return retVal;
-  }
-  else
-      return RT_ERR_FAILED;
-  return  RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_i2c_mode_set
- * Description:
- *      Set I2C data byte-order.
- * Input:
- *      i2cmode - byte-order mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      This API can set I2c traffic's byte-order .
- */
-rtk_api_ret_t rtk_i2c_mode_set( rtk_I2C_16bit_mode_t i2cmode )
-{
-    if(i2cmode >= I2C_Mode_END)
-    {
-        return RT_ERR_INPUT;
-    }
-    else if(i2cmode == I2C_70B_LSB_16BIT_MODE)
-    {
-        rtk_i2c_mode = I2C_70B_LSB_16BIT_MODE;
-
-        return RT_ERR_OK;
-    }
-    else if( i2cmode == I2C_LSB_16BIT_MODE)
-    {
-        rtk_i2c_mode = I2C_LSB_16BIT_MODE;
-        return RT_ERR_OK;
-    }
-    else
-        return RT_ERR_FAILED;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_i2c_mode_get
- * Description:
- *      Get i2c traffic byte-order setting.
- * Input:
- *      None
- * Output:
- *      pI2cMode - i2c byte-order
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_NULL_POINTER     - input parameter is null pointer
- * Note:
- *      The API can get i2c traffic byte-order setting.
- */
-rtk_api_ret_t rtk_i2c_mode_get( rtk_I2C_16bit_mode_t * pI2cMode)
-{
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-    if(NULL == pI2cMode)
-        return RT_ERR_NULL_POINTER;
-    if(rtk_i2c_mode == I2C_70B_LSB_16BIT_MODE)
-        *pI2cMode = 1;
-    else if ((rtk_i2c_mode == I2C_LSB_16BIT_MODE))
-        *pI2cMode = 0;
-    else
-        return RT_ERR_FAILED;
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_i2c_gpioPinGroup_set
- * Description:
- *      Set i2c SDA & SCL used GPIO pins group.
- * Input:
- *      pins_group - GPIO pins group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The API can set i2c used gpio pins group.
- *      There are three group pins could be used
- */
-rtk_api_ret_t rtk_i2c_gpioPinGroup_set( rtk_I2C_gpio_pin_t pins_group )
-{
-    rtk_uint32 retVal;
-
-
-    if( ( pins_group > I2C_GPIO_PIN_END )|| ( pins_group < I2C_GPIO_PIN_8_9) )
-        return RT_ERR_INPUT;
-
-    if( (retVal = rtl8367c_setAsicI2CGpioPinGroup(pins_group) ) != RT_ERR_OK )
-        return retVal ;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_i2c_gpioPinGroup_get
- * Description:
- *      Get i2c SDA & SCL used GPIO pins group.
- * Input:
- *      None
- * Output:
- *      pPins_group - GPIO pins group
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_NULL_POINTER     - input parameter is null pointer
- * Note:
- *      The API can get i2c used gpio pins group.
- *      There are three group pins could be used
- */
-rtk_api_ret_t rtk_i2c_gpioPinGroup_get( rtk_I2C_gpio_pin_t * pPins_group )
-{
-    rtk_uint32 retVal;
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPins_group)
-        return RT_ERR_NULL_POINTER;
-    if( (retVal = rtl8367c_getAsicI2CGpioPinGroup(pPins_group) ) != RT_ERR_OK )
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_i2c_data_read
- * Description:
- *      read i2c slave device register.
- * Input:
- *      deviceAddr   -   access Slave device address
- *      slaveRegAddr -   access Slave register address
- * Output:
- *      pRegData     -   read data
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_NULL_POINTER     - input parameter is null pointer
- * Note:
- *      The API can access i2c slave and read i2c slave device register.
- */
-rtk_api_ret_t rtk_i2c_data_read(rtk_uint8 deviceAddr, rtk_uint32 slaveRegAddr, rtk_uint32 *pRegData)
-{
-     rtk_uint32 retVal, counter=0;
-     rtk_uint8 controlByte_W, controlByte_R;
-     rtk_uint8 slaveRegAddr_L, slaveRegAddr_H = 0x0, temp;
-     rtk_uint8 regData_L, regData_H;
-
-   /* control byte :deviceAddress + W,  deviceAddress + R   */
-    controlByte_W = (rtk_uint8)(deviceAddr << 1) ;
-    controlByte_R = (rtk_uint8)(controlByte_W | 0x1);
-
-    slaveRegAddr_L = (rtk_uint8) (slaveRegAddr & 0x00FF) ;
-    slaveRegAddr_H = (rtk_uint8) (slaveRegAddr >>8) ;
-
-    if( rtk_i2c_mode == I2C_70B_LSB_16BIT_MODE)
-    {
-        temp = slaveRegAddr_L ;
-        slaveRegAddr_L = slaveRegAddr_H;
-        slaveRegAddr_H = temp;
-    }
-
-
-  /*check bus state: idle*/
-  for(counter = 3000; counter>0; counter--)
-  {
-    if ( (retVal = rtl8367c_setAsicI2C_checkBusIdle() ) == RT_ERR_OK)
-         break;
-  }
-  if( counter ==0 )
-      return retVal; /*i2c is busy*/
-
-   /*tx Start cmd*/
-   if( (retVal = rtl8367c_setAsicI2CStartCmd() ) != RT_ERR_OK )
-       return retVal ;
-
-
-  /*tx control _W*/
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(controlByte_W))!= RT_ERR_OK )
-      return retVal ;
-
-
-  /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-    /* tx slave buffer address low 8 bits */
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(slaveRegAddr_L))!= RT_ERR_OK )
-         return retVal  ;
-
-   /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-
-        /* tx slave buffer address high 8 bits */
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(slaveRegAddr_H))!= RT_ERR_OK )
-         return retVal  ;
-
-
-   /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-   /*tx Start cmd*/
-   if( (retVal = rtl8367c_setAsicI2CStartCmd() ) != RT_ERR_OK )
-       return retVal ;
-
-      /*tx control _R*/
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(controlByte_R))!= RT_ERR_OK )
-       return retVal ;
-
-
-  /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-    /* rx low 8bit data*/
-   if( ( retVal = rtl8367c_setAsicI2CRxOneCharCmd( &regData_L) ) != RT_ERR_OK )
-        return retVal;
-
-
-
-    /* tx ack to slave, keep receive */
-    if( (retVal = rtl8367c_setAsicI2CTxAckCmd()) != RT_ERR_OK )
-        return retVal;
-
-     /* rx high 8bit data*/
-    if( ( retVal = rtl8367c_setAsicI2CRxOneCharCmd( &regData_H) ) != RT_ERR_OK )
-        return retVal;
-
-
-
-    /* tx Noack to slave, Stop receive */
-     if( (retVal = rtl8367c_setAsicI2CTxNoAckCmd()) != RT_ERR_OK )
-        return retVal;
-
-
-    /*tx Stop cmd */
-    if( (retVal = rtl8367c_setAsicI2CStopCmd()) != RT_ERR_OK )
-        return retVal;
-
-    *pRegData = (regData_H << 8) | regData_L;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_i2c_data_write
- * Description:
- *      write data to i2c slave device register
- * Input:
- *      deviceAddr   -   access Slave device address
- *      slaveRegAddr -   access Slave register address
- *      regData      -   data to set
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- * Note:
- *      The API can access i2c slave and setting i2c slave device register.
- */
-rtk_api_ret_t rtk_i2c_data_write(rtk_uint8 deviceAddr, rtk_uint32 slaveRegAddr, rtk_uint32 regData)
-{
-     rtk_uint32 retVal,counter;
-     rtk_uint8 controlByte_W;
-     rtk_uint8 slaveRegAddr_L, slaveRegAddr_H = 0x0, temp;
-     rtk_uint8 regData_L, regData_H;
-
-  /* control byte :deviceAddress + W    */
-    controlByte_W = (rtk_uint8)(deviceAddr<< 1) ;
-
-    slaveRegAddr_L = (rtk_uint8) (slaveRegAddr & 0x00FF) ;
-    slaveRegAddr_H = (rtk_uint8) (slaveRegAddr >>8) ;
-
-    regData_H   = (rtk_uint8) (regData>> 8);
-    regData_L   = (rtk_uint8) (regData & 0x00FF);
-
-    if( rtk_i2c_mode == I2C_70B_LSB_16BIT_MODE)
-    {
-        temp = slaveRegAddr_L ;
-        slaveRegAddr_L = slaveRegAddr_H;
-        slaveRegAddr_H = temp;
-    }
-
-
-  /*check bus state: idle*/
-  for(counter = 3000; counter>0; counter--)
-  {
-    if ( (retVal = rtl8367c_setAsicI2C_checkBusIdle() ) == RT_ERR_OK)
-        break;
-  }
-
-  if( counter ==0 )
-      return retVal; /*i2c is busy*/
-
-
-   /*tx Start cmd*/
-   if( (retVal = rtl8367c_setAsicI2CStartCmd() ) != RT_ERR_OK )
-       return retVal ;
-
-
-  /*tx control _W*/
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(controlByte_W))!= RT_ERR_OK )
-      return retVal ;
-
-
-  /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-    /* tx slave buffer address low 8 bits */
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(slaveRegAddr_L))!= RT_ERR_OK )
-        return retVal;
-
-
-   /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-   /* tx slave buffer address high 8 bits */
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(slaveRegAddr_H))!= RT_ERR_OK )
-        return retVal;
-
-
-   /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-     /*tx Datavlue LSB*/
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(regData_L))!= RT_ERR_OK )
-        return retVal;
-
-
-   /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-   /*tx Datavlue MSB*/
-   if( (retVal = rtl8367c_setAsicI2CTxOneCharCmd(regData_H))!= RT_ERR_OK )
-        return retVal;
-
-
-   /*check if RX ack from slave*/
-   if( (retVal = rtl8367c_setAsicI2CcheckRxAck()) != RT_ERR_OK )
-        return retVal;
-
-
-    /*tx Stop cmd */
-    if( (retVal = rtl8367c_setAsicI2CStopCmd()) != RT_ERR_OK )
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/igmp.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/igmp.c
deleted file mode 100644
index 170cbdaaf0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/igmp.c
+++ /dev/null
@@ -1,1555 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in IGMP module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <igmp.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_igmp.h>
-#include <rtl8367c_asicdrv_lut.h>
-
-
-/* Function Name:
- *      rtk_igmp_init
- * Description:
- *      This API enables H/W IGMP and set a default initial configuration.
- * Input:
- *      None.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API enables H/W IGMP and set a default initial configuration.
- */
-rtk_api_ret_t rtk_igmp_init(void)
-{
-    rtk_api_ret_t retVal;
-    rtk_port_t port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_setAsicLutIpMulticastLookup(ENABLED))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicLutIpLookupMethod(1))!=RT_ERR_OK)
-        return retVal;
-
-    RTK_SCAN_ALL_PHY_PORTMASK(port)
-    {
-        if ((retVal = rtl8367c_setAsicIGMPv1Opeartion(port, PROTOCOL_OP_ASIC))!=RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicIGMPv2Opeartion(port, PROTOCOL_OP_ASIC))!=RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicIGMPv3Opeartion(port, PROTOCOL_OP_FLOOD))!=RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicMLDv1Opeartion(port, PROTOCOL_OP_ASIC))!=RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicMLDv2Opeartion(port, PROTOCOL_OP_FLOOD))!=RT_ERR_OK)
-            return retVal;
-    }
-
-    if ((retVal = rtl8367c_setAsicIGMPAllowDynamicRouterPort(rtk_switch_phyPortMask_get()))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPFastLeaveEn(ENABLED))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPReportLeaveFlood(1))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIgmp(ENABLED))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_state_set
- * Description:
- *      This API set H/W IGMP state.
- * Input:
- *      enabled     - H/W IGMP state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set H/W IGMP state.
- */
-rtk_api_ret_t rtk_igmp_state_set(rtk_enable_t enabled)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enabled >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIgmp(enabled))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_state_get
- * Description:
- *      This API get H/W IGMP state.
- * Input:
- *      None.
- * Output:
- *      pEnabled        - H/W IGMP state
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set current H/W IGMP state.
- */
-rtk_api_ret_t rtk_igmp_state_get(rtk_enable_t *pEnabled)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(pEnabled == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIgmp(pEnabled))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_static_router_port_set
- * Description:
- *      Configure static router port
- * Input:
- *      pPortmask    - Static Port mask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API set static router port
- */
-rtk_api_ret_t rtk_igmp_static_router_port_set(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Valid port mask */
-    if(pPortmask == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    RTK_CHK_PORTMASK_VALID(pPortmask);
-
-    if ((retVal = rtk_switch_portmask_L2P_get(pPortmask, &pmask))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPStaticRouterPort(pmask))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_static_router_port_get
- * Description:
- *      Get static router port
- * Input:
- *      None.
- * Output:
- *      pPortmask       - Static port mask
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API get static router port
- */
-rtk_api_ret_t rtk_igmp_static_router_port_get(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(pPortmask == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPStaticRouterPort(&pmask))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_protocol_set
- * Description:
- *      set IGMP/MLD protocol action
- * Input:
- *      port        - Port ID
- *      protocol    - IGMP/MLD protocol
- *      action      - Per-port and per-protocol IGMP action seeting
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API set IGMP/MLD protocol action
- */
-rtk_api_ret_t rtk_igmp_protocol_set(rtk_port_t port, rtk_igmp_protocol_t protocol, rtk_igmp_action_t action)
-{
-    rtk_uint32      operation;
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(protocol >= PROTOCOL_END)
-        return RT_ERR_INPUT;
-
-    if(action >= IGMP_ACTION_END)
-        return RT_ERR_INPUT;
-
-    switch(action)
-    {
-        case IGMP_ACTION_FORWARD:
-            operation = PROTOCOL_OP_FLOOD;
-            break;
-        case IGMP_ACTION_TRAP2CPU:
-            operation = PROTOCOL_OP_TRAP;
-            break;
-        case IGMP_ACTION_DROP:
-            operation = PROTOCOL_OP_DROP;
-            break;
-        case IGMP_ACTION_ASIC:
-            operation = PROTOCOL_OP_ASIC;
-            break;
-        default:
-            return RT_ERR_INPUT;
-    }
-
-    switch(protocol)
-    {
-        case PROTOCOL_IGMPv1:
-            if ((retVal = rtl8367c_setAsicIGMPv1Opeartion(rtk_switch_port_L2P_get(port), operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_IGMPv2:
-            if ((retVal = rtl8367c_setAsicIGMPv2Opeartion(rtk_switch_port_L2P_get(port), operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_IGMPv3:
-            if ((retVal = rtl8367c_setAsicIGMPv3Opeartion(rtk_switch_port_L2P_get(port), operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_MLDv1:
-            if ((retVal = rtl8367c_setAsicMLDv1Opeartion(rtk_switch_port_L2P_get(port), operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_MLDv2:
-            if ((retVal = rtl8367c_setAsicMLDv2Opeartion(rtk_switch_port_L2P_get(port), operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        default:
-            return RT_ERR_INPUT;
-
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_protocol_get
- * Description:
- *      set IGMP/MLD protocol action
- * Input:
- *      port        - Port ID
- *      protocol    - IGMP/MLD protocol
- *      action      - Per-port and per-protocol IGMP action seeting
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API set IGMP/MLD protocol action
- */
-rtk_api_ret_t rtk_igmp_protocol_get(rtk_port_t port, rtk_igmp_protocol_t protocol, rtk_igmp_action_t *pAction)
-{
-    rtk_uint32      operation;
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(protocol >= PROTOCOL_END)
-        return RT_ERR_INPUT;
-
-    if(pAction == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    switch(protocol)
-    {
-        case PROTOCOL_IGMPv1:
-            if ((retVal = rtl8367c_getAsicIGMPv1Opeartion(rtk_switch_port_L2P_get(port), &operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_IGMPv2:
-            if ((retVal = rtl8367c_getAsicIGMPv2Opeartion(rtk_switch_port_L2P_get(port), &operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_IGMPv3:
-            if ((retVal = rtl8367c_getAsicIGMPv3Opeartion(rtk_switch_port_L2P_get(port), &operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_MLDv1:
-            if ((retVal = rtl8367c_getAsicMLDv1Opeartion(rtk_switch_port_L2P_get(port), &operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        case PROTOCOL_MLDv2:
-            if ((retVal = rtl8367c_getAsicMLDv2Opeartion(rtk_switch_port_L2P_get(port), &operation))!=RT_ERR_OK)
-                return retVal;
-
-            break;
-        default:
-            return RT_ERR_INPUT;
-
-    }
-
-    switch(operation)
-    {
-        case PROTOCOL_OP_FLOOD:
-            *pAction = IGMP_ACTION_FORWARD;
-            break;
-        case PROTOCOL_OP_TRAP:
-            *pAction = IGMP_ACTION_TRAP2CPU;
-            break;
-        case PROTOCOL_OP_DROP:
-            *pAction = IGMP_ACTION_DROP;
-            break;
-        case PROTOCOL_OP_ASIC:
-            *pAction = IGMP_ACTION_ASIC;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_fastLeave_set
- * Description:
- *      set IGMP/MLD FastLeave state
- * Input:
- *      state       - ENABLED: Enable FastLeave, DISABLED: disable FastLeave
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API set IGMP/MLD FastLeave state
- */
-rtk_api_ret_t rtk_igmp_fastLeave_set(rtk_enable_t state)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(state >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPFastLeaveEn((rtk_uint32)state))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_fastLeave_get
- * Description:
- *      get IGMP/MLD FastLeave state
- * Input:
- *      None
- * Output:
- *      pState      - ENABLED: Enable FastLeave, DISABLED: disable FastLeave
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - NULL pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API get IGMP/MLD FastLeave state
- */
-rtk_api_ret_t rtk_igmp_fastLeave_get(rtk_enable_t *pState)
-{
-    rtk_uint32      fast_leave;
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(pState == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPFastLeaveEn(&fast_leave))!=RT_ERR_OK)
-        return retVal;
-
-    *pState = ((fast_leave == 1) ? ENABLED : DISABLED);
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_maxGroup_set
- * Description:
- *      Set per port multicast group learning limit.
- * Input:
- *      port        - Port ID
- *      group       - The number of multicast group learning limit.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_PORT_ID         - Error Port ID
- *      RT_ERR_OUT_OF_RANGE    - parameter out of range
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API set per port multicast group learning limit.
- */
-rtk_api_ret_t rtk_igmp_maxGroup_set(rtk_port_t port, rtk_uint32 group)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(group > RTL8367C_IGMP_MAX_GOUP)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if ((retVal = rtl8367c_setAsicIGMPPortMAXGroup(rtk_switch_port_L2P_get(port), group))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_maxGroup_get
- * Description:
- *      Get per port multicast group learning limit.
- * Input:
- *      port        - Port ID
- * Output:
- *      pGroup      - The number of multicast group learning limit.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_PORT_ID         - Error Port ID
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API get per port multicast group learning limit.
- */
-rtk_api_ret_t rtk_igmp_maxGroup_get(rtk_port_t port, rtk_uint32 *pGroup)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(pGroup == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPPortMAXGroup(rtk_switch_port_L2P_get(port), pGroup))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_currentGroup_get
- * Description:
- *      Get per port multicast group learning count.
- * Input:
- *      port        - Port ID
- * Output:
- *      pGroup      - The number of multicast group learning count.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_PORT_ID         - Error Port ID
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API get per port multicast group learning count.
- */
-rtk_api_ret_t rtk_igmp_currentGroup_get(rtk_port_t port, rtk_uint32 *pGroup)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(pGroup == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPPortCurrentGroup(rtk_switch_port_L2P_get(port), pGroup))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_tableFullAction_set
- * Description:
- *      set IGMP/MLD Table Full Action
- * Input:
- *      action      - Table Full Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_tableFullAction_set(rtk_igmp_tableFullAction_t action)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(action >= IGMP_TABLE_FULL_OP_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPTableFullOP((rtk_uint32)action))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_tableFullAction_get
- * Description:
- *      get IGMP/MLD Table Full Action
- * Input:
- *      None
- * Output:
- *      pAction     - Table Full Action
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_tableFullAction_get(rtk_igmp_tableFullAction_t *pAction)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPTableFullOP((rtk_uint32 *)pAction))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_checksumErrorAction_set
- * Description:
- *      set IGMP/MLD Checksum Error Action
- * Input:
- *      action      - Checksum error Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_checksumErrorAction_set(rtk_igmp_checksumErrorAction_t action)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(action >= IGMP_CRC_ERR_OP_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPCRCErrOP((rtk_uint32)action))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_igmp_checksumErrorAction_get
- * Description:
- *      get IGMP/MLD Checksum Error Action
- * Input:
- *      None
- * Output:
- *      pAction     - Checksum error Action
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_checksumErrorAction_get(rtk_igmp_checksumErrorAction_t *pAction)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPCRCErrOP((rtk_uint32 *)pAction))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_leaveTimer_set
- * Description:
- *      set IGMP/MLD Leave timer
- * Input:
- *      timer       - Leave timer
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_leaveTimer_set(rtk_uint32 timer)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(timer > RTL8367C_MAX_LEAVE_TIMER)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPLeaveTimer(timer))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_leaveTimer_get
- * Description:
- *      get IGMP/MLD Leave timer
- * Input:
- *      None
- * Output:
- *      pTimer      - Leave Timer.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_leaveTimer_get(rtk_uint32 *pTimer)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pTimer)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPLeaveTimer(pTimer))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_queryInterval_set
- * Description:
- *      set IGMP/MLD Query Interval
- * Input:
- *      interval     - Query Interval
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_queryInterval_set(rtk_uint32 interval)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(interval > RTL8367C_MAX_QUERY_INT)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPQueryInterval(interval))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_queryInterval_get
- * Description:
- *      get IGMP/MLD Query Interval
- * Input:
- *      None.
- * Output:
- *      pInterval   - Query Interval
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_queryInterval_get(rtk_uint32 *pInterval)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pInterval)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPQueryInterval(pInterval))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_robustness_set
- * Description:
- *      set IGMP/MLD Robustness value
- * Input:
- *      robustness     - Robustness value
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_robustness_set(rtk_uint32 robustness)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(robustness > RTL8367C_MAX_ROB_VAR)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPRobVar(robustness))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_robustness_get
- * Description:
- *      get IGMP/MLD Robustness value
- * Input:
- *      None
- * Output:
- *      pRobustness     - Robustness value.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_igmp_robustness_get(rtk_uint32 *pRobustness)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pRobustness)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPRobVar(pRobustness))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_dynamicRouterRortAllow_set
- * Description:
- *      Configure dynamic router port allow option
- * Input:
- *      pPortmask    - Dynamic Port allow mask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_dynamicRouterPortAllow_set(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    RTK_CHK_PORTMASK_VALID(pPortmask);
-
-    if ((retVal = rtk_switch_portmask_L2P_get(pPortmask, &pmask))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPAllowDynamicRouterPort(pmask))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_dynamicRouterRortAllow_get
- * Description:
- *      Get dynamic router port allow option
- * Input:
- *      None.
- * Output:
- *      pPortmask    - Dynamic Port allow mask
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_dynamicRouterPortAllow_get(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPAllowDynamicRouterPort(&pmask))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_dynamicRouterPort_get
- * Description:
- *      Get dynamic router port
- * Input:
- *      None.
- * Output:
- *      pDynamicRouterPort    - Dynamic Router Port
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_dynamicRouterPort_get(rtk_igmp_dynamicRouterPort_t *pDynamicRouterPort)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32 port;
-    rtk_uint32 timer;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pDynamicRouterPort)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPdynamicRouterPort1(&port, &timer))!= RT_ERR_OK)
-        return retVal;
-
-    if (port == RTL8367C_ROUTER_PORT_INVALID)
-    {
-        pDynamicRouterPort->dynamicRouterPort0Valid = DISABLED;
-        pDynamicRouterPort->dynamicRouterPort0      = 0;
-        pDynamicRouterPort->dynamicRouterPort0Timer = 0;
-    }
-    else
-    {
-        pDynamicRouterPort->dynamicRouterPort0Valid = ENABLED;
-        pDynamicRouterPort->dynamicRouterPort0      = rtk_switch_port_P2L_get(port);
-        pDynamicRouterPort->dynamicRouterPort0Timer = timer;
-    }
-
-    if ((retVal = rtl8367c_getAsicIGMPdynamicRouterPort2(&port, &timer))!= RT_ERR_OK)
-        return retVal;
-
-    if (port == RTL8367C_ROUTER_PORT_INVALID)
-    {
-        pDynamicRouterPort->dynamicRouterPort1Valid = DISABLED;
-        pDynamicRouterPort->dynamicRouterPort1      = 0;
-        pDynamicRouterPort->dynamicRouterPort1Timer = 0;
-    }
-    else
-    {
-        pDynamicRouterPort->dynamicRouterPort1Valid = ENABLED;
-        pDynamicRouterPort->dynamicRouterPort1      = rtk_switch_port_P2L_get(port);
-        pDynamicRouterPort->dynamicRouterPort1Timer = timer;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_suppressionEnable_set
- * Description:
- *      Configure IGMPv1/v2 & MLDv1 Report/Leave/Done suppression
- * Input:
- *      reportSuppression   - Report suppression
- *      leaveSuppression    - Leave suppression
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_suppressionEnable_set(rtk_enable_t reportSuppression, rtk_enable_t leaveSuppression)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(reportSuppression >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(leaveSuppression >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPSuppression((rtk_uint32)reportSuppression, (rtk_uint32)leaveSuppression))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_suppressionEnable_get
- * Description:
- *      Get IGMPv1/v2 & MLDv1 Report/Leave/Done suppression
- * Input:
- *      None
- * Output:
- *      pReportSuppression  - Report suppression
- *      pLeaveSuppression   - Leave suppression
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_suppressionEnable_get(rtk_enable_t *pReportSuppression, rtk_enable_t *pLeaveSuppression)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pReportSuppression)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pLeaveSuppression)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPSuppression((rtk_uint32 *)pReportSuppression, (rtk_uint32 *)pLeaveSuppression))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_portRxPktEnable_set
- * Description:
- *      Configure IGMP/MLD RX Packet configuration
- * Input:
- *      port       - Port ID
- *      pRxCfg     - RX Packet Configuration
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_portRxPktEnable_set(rtk_port_t port, rtk_igmp_rxPktEnable_t *pRxCfg)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pRxCfg)
-        return RT_ERR_NULL_POINTER;
-
-    if(pRxCfg->rxQuery >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(pRxCfg->rxReport >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(pRxCfg->rxLeave >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(pRxCfg->rxMRP >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(pRxCfg->rxMcast >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPQueryRX(rtk_switch_port_L2P_get(port), (rtk_uint32)pRxCfg->rxQuery))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPReportRX(rtk_switch_port_L2P_get(port), (rtk_uint32)pRxCfg->rxReport))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPLeaveRX(rtk_switch_port_L2P_get(port), (rtk_uint32)pRxCfg->rxLeave))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPMRPRX(rtk_switch_port_L2P_get(port), (rtk_uint32)pRxCfg->rxMRP))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicIGMPMcDataRX(rtk_switch_port_L2P_get(port), (rtk_uint32)pRxCfg->rxMcast))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_portRxPktEnable_get
- * Description:
- *      Get IGMP/MLD RX Packet configuration
- * Input:
- *      port       - Port ID
- *      pRxCfg     - RX Packet Configuration
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_portRxPktEnable_get(rtk_port_t port, rtk_igmp_rxPktEnable_t *pRxCfg)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pRxCfg)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPQueryRX(rtk_switch_port_L2P_get(port), (rtk_uint32 *)&(pRxCfg->rxQuery)))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicIGMPReportRX(rtk_switch_port_L2P_get(port), (rtk_uint32 *)&(pRxCfg->rxReport)))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicIGMPLeaveRX(rtk_switch_port_L2P_get(port), (rtk_uint32 *)&(pRxCfg->rxLeave)))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicIGMPMRPRX(rtk_switch_port_L2P_get(port), (rtk_uint32 *)&(pRxCfg->rxMRP)))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicIGMPMcDataRX(rtk_switch_port_L2P_get(port), (rtk_uint32 *)&(pRxCfg->rxMcast)))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_groupInfo_get
- * Description:
- *      Get IGMP/MLD Group database
- * Input:
- *      indes       - Index (0~255)
- * Output:
- *      pGroup      - Group database information.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_groupInfo_get(rtk_uint32 index, rtk_igmp_groupInfo_t *pGroup)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      valid;
-    rtl8367c_igmpgroup  grp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check index */
-    if(index > RTL8367C_IGMP_MAX_GOUP)
-        return RT_ERR_INPUT;
-
-    if(NULL == pGroup)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPGroup(index, &valid, &grp))!=RT_ERR_OK)
-        return retVal;
-
-    memset(pGroup, 0x00, sizeof(rtk_igmp_groupInfo_t));
-    pGroup->valid = valid;
-    pGroup->reportSuppFlag = grp.report_supp_flag;
-
-    if(grp.p0_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(0));
-        pGroup->timer[rtk_switch_port_P2L_get(0)] = grp.p0_timer;
-    }
-
-    if(grp.p1_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(1));
-        pGroup->timer[rtk_switch_port_P2L_get(1)] = grp.p1_timer;
-    }
-
-    if(grp.p2_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(2));
-        pGroup->timer[rtk_switch_port_P2L_get(2)] = grp.p2_timer;
-    }
-
-    if(grp.p3_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(3));
-        pGroup->timer[rtk_switch_port_P2L_get(3)] = grp.p3_timer;
-    }
-
-    if(grp.p4_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(4));
-        pGroup->timer[rtk_switch_port_P2L_get(4)] = grp.p4_timer;
-    }
-
-    if(grp.p5_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(5));
-        pGroup->timer[rtk_switch_port_P2L_get(5)] = grp.p5_timer;
-    }
-
-    if(grp.p6_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(6));
-        pGroup->timer[rtk_switch_port_P2L_get(6)] = grp.p6_timer;
-    }
-
-    if(grp.p7_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(7));
-        pGroup->timer[rtk_switch_port_P2L_get(7)] = grp.p7_timer;
-    }
-
-    if(grp.p8_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(8));
-        pGroup->timer[rtk_switch_port_P2L_get(8)] = grp.p8_timer;
-    }
-
-    if(grp.p9_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(9));
-        pGroup->timer[rtk_switch_port_P2L_get(9)] = grp.p9_timer;
-    }
-
-    if(grp.p10_timer != 0)
-    {
-        RTK_PORTMASK_PORT_SET((pGroup->member), rtk_switch_port_P2L_get(10));
-        pGroup->timer[rtk_switch_port_P2L_get(10)] = grp.p10_timer;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_ReportLeaveFwdAction_set
- * Description:
- *      Set Report Leave packet forwarding action
- * Input:
- *      action      - Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_ReportLeaveFwdAction_set(rtk_igmp_ReportLeaveFwdAct_t action)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    switch(action)
-    {
-        case IGMP_REPORT_LEAVE_TO_ROUTER:
-            regData = 1;
-            break;
-        case IGMP_REPORT_LEAVE_TO_ALLPORT:
-            regData = 2;
-            break;
-        case IGMP_REPORT_LEAVE_TO_ROUTER_PORT_ADV:
-            regData = 3;
-            break;
-        default:
-            return RT_ERR_INPUT;
-    }
-
-    if ((retVal = rtl8367c_setAsicIGMPReportLeaveFlood(regData))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_ReportLeaveFwdAction_get
- * Description:
- *      Get Report Leave packet forwarding action
- * Input:
- *      action      - Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null Pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_ReportLeaveFwdAction_get(rtk_igmp_ReportLeaveFwdAct_t *pAction)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPReportLeaveFlood(&regData))!=RT_ERR_OK)
-        return retVal;
-
-    switch(regData)
-    {
-        case 1:
-            *pAction = IGMP_REPORT_LEAVE_TO_ROUTER;
-            break;
-        case 2:
-            *pAction = IGMP_REPORT_LEAVE_TO_ALLPORT;
-            break;
-        case 3:
-            *pAction = IGMP_REPORT_LEAVE_TO_ROUTER_PORT_ADV;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_dropLeaveZeroEnable_set
- * Description:
- *      Set the function of droppping Leave packet with group IP = 0.0.0.0
- * Input:
- *      enabled      - Action 1: drop, 0:pass
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_dropLeaveZeroEnable_set(rtk_enable_t enabled)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(enabled >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPDropLeaveZero(enabled))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_igmp_dropLeaveZeroEnable_get
- * Description:
- *      Get the function of droppping Leave packet with group IP = 0.0.0.0
- * Input:
- *      None
- * Output:
- *      pEnabled.   - Action 1: drop, 0:pass
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null Pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_dropLeaveZeroEnable_get(rtk_enable_t *pEnabled)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPDropLeaveZero((rtk_uint32 *)pEnabled))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_igmp_bypassGroupRange_set
- * Description:
- *      Set Bypass group
- * Input:
- *      group       - bypassed group
- *      enabled     - enabled 1: Bypassed, 0: not bypass
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_bypassGroupRange_set(rtk_igmp_bypassGroup_t group, rtk_enable_t enabled)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(group >= IGMP_BYPASS_GROUP_END)
-        return RT_ERR_INPUT;
-
-    if(enabled >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicIGMPBypassGroup(group, enabled))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_igmp_bypassGroupRange_get
- * Description:
- *      get Bypass group
- * Input:
- *      group       - bypassed group
- * Output:
- *      pEnable     - enabled 1: Bypassed, 0: not bypass
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null Pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_igmp_bypassGroupRange_get(rtk_igmp_bypassGroup_t group, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(group >= IGMP_BYPASS_GROUP_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicIGMPBypassGroup(group, pEnable))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/acl.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/acl.h
deleted file mode 100644
index 6308da8d42..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/acl.h
+++ /dev/null
@@ -1,990 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes ACL module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_ACL_H__
-#define __RTK_API_ACL_H__
-
-/*
- * Data Type Declaration
- */
-#define RTK_FILTER_RAW_FIELD_NUMBER                8
-
-#define ACL_DEFAULT_ABILITY                         0
-#define ACL_DEFAULT_UNMATCH_PERMIT                  1
-
-#define ACL_RULE_FREE                               0
-#define ACL_RULE_INAVAILABLE                        1
-#define ACL_RULE_CARETAG_MASK                       0x1F
-#define FILTER_POLICING_MAX                         4
-#define FILTER_LOGGING_MAX                          8
-#define FILTER_PATTERN_MAX                          4
-
-#define FILTER_ENACT_CVLAN_MASK         0x01
-#define FILTER_ENACT_SVLAN_MASK         0x02
-#define FILTER_ENACT_PRIORITY_MASK      0x04
-#define FILTER_ENACT_POLICING_MASK      0x08
-#define FILTER_ENACT_FWD_MASK           0x10
-#define FILTER_ENACT_INTGPIO_MASK       0x20
-#define FILTER_ENACT_INIT_MASK          0x3F
-
-typedef enum rtk_filter_act_cactext_e
-{
-    FILTER_ENACT_CACTEXT_VLANONLY=0,
-    FILTER_ENACT_CACTEXT_BOTHVLANTAG,
-    FILTER_ENACT_CACTEXT_TAGONLY,
-    FILTER_ENACT_CACTEXT_END,
-
-
-}rtk_filter_act_cactext_t;
-
-typedef enum rtk_filter_act_ctagfmt_e
-{
-    FILTER_CTAGFMT_UNTAG=0,
-    FILTER_CTAGFMT_TAG,
-    FILTER_CTAGFMT_KEEP,
-    FILTER_CTAGFMT_KEEP1PRMK,
-
-
-}rtk_filter_act_ctag_t;
-
-
-
-
-
-#define RTK_MAX_NUM_OF_FILTER_TYPE                  5
-#define RTK_MAX_NUM_OF_FILTER_FIELD                 8
-
-#define RTK_DOT_1AS_TIMESTAMP_UNIT_IN_WORD_LENGTH   3UL
-#define RTK_IPV6_ADDR_WORD_LENGTH                   4UL
-
-#define FILTER_ENACT_CVLAN_TYPE(type)   (type - FILTER_ENACT_CVLAN_INGRESS)
-#define FILTER_ENACT_SVLAN_TYPE(type)   (type - FILTER_ENACT_SVLAN_INGRESS)
-#define FILTER_ENACT_FWD_TYPE(type)     (type - FILTER_ENACT_ADD_DSTPORT)
-#define FILTER_ENACT_PRI_TYPE(type)     (type - FILTER_ENACT_PRIORITY)
-
-#define RTK_FILTER_FIELD_USED_MAX                   8
-#define RTK_FILTER_FIELD_INDEX(template, index)     ((template << 4) + index)
-
-
-typedef enum rtk_filter_act_enable_e
-{
-    /* CVLAN */
-    FILTER_ENACT_CVLAN_INGRESS = 0,
-    FILTER_ENACT_CVLAN_EGRESS,
-    FILTER_ENACT_CVLAN_SVID,
-    FILTER_ENACT_POLICING_1,
-
-    /* SVLAN */
-    FILTER_ENACT_SVLAN_INGRESS,
-    FILTER_ENACT_SVLAN_EGRESS,
-    FILTER_ENACT_SVLAN_CVID,
-    FILTER_ENACT_POLICING_2,
-
-    /* Policing and Logging */
-    FILTER_ENACT_POLICING_0,
-
-    /* Forward */
-    FILTER_ENACT_COPY_CPU,
-    FILTER_ENACT_DROP,
-    FILTER_ENACT_ADD_DSTPORT,
-    FILTER_ENACT_REDIRECT,
-    FILTER_ENACT_MIRROR,
-    FILTER_ENACT_TRAP_CPU,
-    FILTER_ENACT_ISOLATION,
-
-    /* QoS */
-    FILTER_ENACT_PRIORITY,
-    FILTER_ENACT_DSCP_REMARK,
-    FILTER_ENACT_1P_REMARK,
-    FILTER_ENACT_POLICING_3,
-
-    /* Interrutp and GPO */
-    FILTER_ENACT_INTERRUPT,
-    FILTER_ENACT_GPO,
-
-    /*VLAN tag*/
-    FILTER_ENACT_EGRESSCTAG_UNTAG,
-    FILTER_ENACT_EGRESSCTAG_TAG,
-    FILTER_ENACT_EGRESSCTAG_KEEP,
-    FILTER_ENACT_EGRESSCTAG_KEEPAND1PRMK,
-
-    FILTER_ENACT_END,
-} rtk_filter_act_enable_t;
-
-
-typedef struct
-{
-    rtk_filter_act_enable_t actEnable[FILTER_ENACT_END];
-
-    /* CVLAN acton */
-    rtk_uint32      filterCvlanVid;
-    rtk_uint32      filterCvlanIdx;
-    /* SVLAN action */
-    rtk_uint32      filterSvlanVid;
-    rtk_uint32      filterSvlanIdx;
-
-    /* Policing action */
-    rtk_uint32      filterPolicingIdx[FILTER_POLICING_MAX];
-
-    /* Forwarding action */
-    rtk_portmask_t  filterPortmask;
-
-    /* QOS action */
-    rtk_uint32      filterPriority;
-
-    /*GPO*/
-    rtk_uint32      filterPin;
-
-} rtk_filter_action_t;
-
-typedef struct rtk_filter_flag_s
-{
-    rtk_uint32 value;
-    rtk_uint32 mask;
-} rtk_filter_flag_t;
-
-typedef enum rtk_filter_care_tag_index_e
-{
-    CARE_TAG_CTAG = 0,
-    CARE_TAG_STAG,
-    CARE_TAG_PPPOE,
-    CARE_TAG_IPV4,
-    CARE_TAG_IPV6,
-    CARE_TAG_TCP,
-    CARE_TAG_UDP,
-    CARE_TAG_ARP,
-    CARE_TAG_RSV1,
-    CARE_TAG_RSV2,
-    CARE_TAG_ICMP,
-    CARE_TAG_IGMP,
-    CARE_TAG_LLC,
-    CARE_TAG_RSV3,
-    CARE_TAG_HTTP,
-    CARE_TAG_RSV4,
-    CARE_TAG_RSV5,
-    CARE_TAG_DHCP,
-    CARE_TAG_DHCPV6,
-    CARE_TAG_SNMP,
-    CARE_TAG_OAM,
-    CARE_TAG_END,
-} rtk_filter_care_tag_index_t;
-
-typedef struct rtk_filter_care_tag_s
-{
-    rtk_filter_flag_t tagType[CARE_TAG_END];
-} rtk_filter_care_tag_t;
-
-typedef struct rtk_filter_field rtk_filter_field_t;
-
-typedef struct
-{
-    rtk_uint32 value[RTK_DOT_1AS_TIMESTAMP_UNIT_IN_WORD_LENGTH];
-} rtk_filter_dot1as_timestamp_t;
-
-typedef enum rtk_filter_field_data_type_e
-{
-    FILTER_FIELD_DATA_MASK = 0,
-    FILTER_FIELD_DATA_RANGE,
-    FILTER_FIELD_DATA_END ,
-} rtk_filter_field_data_type_t;
-
-typedef struct rtk_filter_ip_s
-{
-    rtk_uint32 dataType;
-    rtk_uint32 rangeStart;
-    rtk_uint32 rangeEnd;
-    rtk_uint32 value;
-    rtk_uint32 mask;
-} rtk_filter_ip_t;
-
-typedef struct rtk_filter_mac_s
-{
-    rtk_uint32 dataType;
-    rtk_mac_t value;
-    rtk_mac_t mask;
-    rtk_mac_t rangeStart;
-    rtk_mac_t rangeEnd;
-} rtk_filter_mac_t;
-
-typedef rtk_uint32 rtk_filter_op_t;
-
-typedef struct rtk_filter_value_s
-{
-    rtk_uint32 dataType;
-    rtk_uint32 value;
-    rtk_uint32 mask;
-    rtk_uint32 rangeStart;
-    rtk_uint32 rangeEnd;
-
-} rtk_filter_value_t;
-
-typedef struct rtk_filter_activeport_s
-{
-    rtk_portmask_t value;
-    rtk_portmask_t mask;
-
-} rtk_filter_activeport_t;
-
-
-
-typedef struct rtk_filter_tag_s
-{
-    rtk_filter_value_t pri;
-    rtk_filter_flag_t cfi;
-    rtk_filter_value_t vid;
-} rtk_filter_tag_t;
-
-typedef struct rtk_filter_ipFlag_s
-{
-    rtk_filter_flag_t xf;
-    rtk_filter_flag_t mf;
-    rtk_filter_flag_t df;
-} rtk_filter_ipFlag_t;
-
-typedef struct
-{
-    rtk_uint32 addr[RTK_IPV6_ADDR_WORD_LENGTH];
-} rtk_filter_ip6_addr_t;
-
-typedef struct
-{
-    rtk_uint32 dataType;
-    rtk_filter_ip6_addr_t value;
-    rtk_filter_ip6_addr_t mask;
-    rtk_filter_ip6_addr_t rangeStart;
-    rtk_filter_ip6_addr_t rangeEnd;
-} rtk_filter_ip6_t;
-
-typedef rtk_uint32 rtk_filter_number_t;
-
-typedef struct rtk_filter_pattern_s
-{
-    rtk_uint32 value[FILTER_PATTERN_MAX];
-    rtk_uint32 mask[FILTER_PATTERN_MAX];
-} rtk_filter_pattern_t;
-
-typedef struct rtk_filter_tcpFlag_s
-{
-    rtk_filter_flag_t urg;
-    rtk_filter_flag_t ack;
-    rtk_filter_flag_t psh;
-    rtk_filter_flag_t rst;
-    rtk_filter_flag_t syn;
-    rtk_filter_flag_t fin;
-    rtk_filter_flag_t ns;
-    rtk_filter_flag_t cwr;
-    rtk_filter_flag_t ece;
-} rtk_filter_tcpFlag_t;
-
-typedef rtk_uint32 rtk_filter_field_raw_t;
-
-typedef enum rtk_filter_field_temple_input_e
-{
-    FILTER_FIELD_TEMPLE_INPUT_TYPE = 0,
-    FILTER_FIELD_TEMPLE_INPUT_INDEX,
-    FILTER_FIELD_TEMPLE_INPUT_MAX ,
-} rtk_filter_field_temple_input_t;
-
-struct rtk_filter_field
-{
-    rtk_uint32 fieldType;
-
-    union
-    {
-        /* L2 struct */
-        rtk_filter_mac_t       dmac;
-        rtk_filter_mac_t       smac;
-        rtk_filter_value_t     etherType;
-        rtk_filter_tag_t       ctag;
-        rtk_filter_tag_t       relayCtag;
-        rtk_filter_tag_t       stag;
-        rtk_filter_tag_t       l2tag;
-        rtk_filter_dot1as_timestamp_t dot1asTimeStamp;
-        rtk_filter_mac_t       mac;
-
-        /* L3 struct */
-        rtk_filter_ip_t      sip;
-        rtk_filter_ip_t      dip;
-        rtk_filter_ip_t      ip;
-        rtk_filter_value_t   protocol;
-        rtk_filter_value_t   ipTos;
-        rtk_filter_ipFlag_t  ipFlag;
-        rtk_filter_value_t   ipOffset;
-        rtk_filter_ip6_t     sipv6;
-        rtk_filter_ip6_t     dipv6;
-        rtk_filter_ip6_t     ipv6;
-        rtk_filter_value_t   ipv6TrafficClass;
-        rtk_filter_value_t   ipv6NextHeader;
-        rtk_filter_value_t   flowLabel;
-
-        /* L4 struct */
-        rtk_filter_value_t   tcpSrcPort;
-        rtk_filter_value_t   tcpDstPort;
-        rtk_filter_tcpFlag_t tcpFlag;
-        rtk_filter_value_t   tcpSeqNumber;
-        rtk_filter_value_t   tcpAckNumber;
-        rtk_filter_value_t   udpSrcPort;
-        rtk_filter_value_t   udpDstPort;
-        rtk_filter_value_t   icmpCode;
-        rtk_filter_value_t   icmpType;
-        rtk_filter_value_t   igmpType;
-
-        /* pattern match */
-        rtk_filter_pattern_t pattern;
-
-        rtk_filter_value_t   inData;
-
-    } filter_pattern_union;
-
-    rtk_uint32 fieldTemplateNo;
-    rtk_uint32 fieldTemplateIdx[RTK_FILTER_FIELD_USED_MAX];
-
-    struct rtk_filter_field *next;
-};
-
-typedef enum rtk_filter_field_type_e
-{
-    FILTER_FIELD_DMAC = 0,
-    FILTER_FIELD_SMAC,
-    FILTER_FIELD_ETHERTYPE,
-    FILTER_FIELD_CTAG,
-    FILTER_FIELD_STAG,
-
-    FILTER_FIELD_IPV4_SIP,
-    FILTER_FIELD_IPV4_DIP,
-    FILTER_FIELD_IPV4_TOS,
-    FILTER_FIELD_IPV4_PROTOCOL,
-    FILTER_FIELD_IPV4_FLAG,
-    FILTER_FIELD_IPV4_OFFSET,
-    FILTER_FIELD_IPV6_SIPV6,
-    FILTER_FIELD_IPV6_DIPV6,
-    FILTER_FIELD_IPV6_TRAFFIC_CLASS,
-    FILTER_FIELD_IPV6_NEXT_HEADER,
-
-    FILTER_FIELD_TCP_SPORT,
-    FILTER_FIELD_TCP_DPORT,
-    FILTER_FIELD_TCP_FLAG,
-    FILTER_FIELD_UDP_SPORT,
-    FILTER_FIELD_UDP_DPORT,
-    FILTER_FIELD_ICMP_CODE,
-    FILTER_FIELD_ICMP_TYPE,
-    FILTER_FIELD_IGMP_TYPE,
-
-    FILTER_FIELD_VID_RANGE,
-    FILTER_FIELD_IP_RANGE,
-    FILTER_FIELD_PORT_RANGE,
-
-    FILTER_FIELD_USER_DEFINED00,
-    FILTER_FIELD_USER_DEFINED01,
-    FILTER_FIELD_USER_DEFINED02,
-    FILTER_FIELD_USER_DEFINED03,
-    FILTER_FIELD_USER_DEFINED04,
-    FILTER_FIELD_USER_DEFINED05,
-    FILTER_FIELD_USER_DEFINED06,
-    FILTER_FIELD_USER_DEFINED07,
-    FILTER_FIELD_USER_DEFINED08,
-    FILTER_FIELD_USER_DEFINED09,
-    FILTER_FIELD_USER_DEFINED10,
-    FILTER_FIELD_USER_DEFINED11,
-    FILTER_FIELD_USER_DEFINED12,
-    FILTER_FIELD_USER_DEFINED13,
-    FILTER_FIELD_USER_DEFINED14,
-    FILTER_FIELD_USER_DEFINED15,
-
-    FILTER_FIELD_PATTERN_MATCH,
-
-    FILTER_FIELD_END,
-} rtk_filter_field_type_t;
-
-
-typedef enum rtk_filter_field_type_raw_e
-{
-    FILTER_FIELD_RAW_UNUSED = 0,
-    FILTER_FIELD_RAW_DMAC_15_0,
-    FILTER_FIELD_RAW_DMAC_31_16,
-    FILTER_FIELD_RAW_DMAC_47_32,
-    FILTER_FIELD_RAW_SMAC_15_0,
-    FILTER_FIELD_RAW_SMAC_31_16,
-    FILTER_FIELD_RAW_SMAC_47_32,
-    FILTER_FIELD_RAW_ETHERTYPE,
-    FILTER_FIELD_RAW_STAG,
-    FILTER_FIELD_RAW_CTAG,
-
-    FILTER_FIELD_RAW_IPV4_SIP_15_0 = 0x10,
-    FILTER_FIELD_RAW_IPV4_SIP_31_16,
-    FILTER_FIELD_RAW_IPV4_DIP_15_0,
-    FILTER_FIELD_RAW_IPV4_DIP_31_16,
-
-
-    FILTER_FIELD_RAW_IPV6_SIP_15_0 = 0x20,
-    FILTER_FIELD_RAW_IPV6_SIP_31_16,
-    FILTER_FIELD_RAW_IPV6_DIP_15_0 = 0x28,
-    FILTER_FIELD_RAW_IPV6_DIP_31_16,
-
-    FILTER_FIELD_RAW_VIDRANGE = 0x30,
-    FILTER_FIELD_RAW_IPRANGE,
-    FILTER_FIELD_RAW_PORTRANGE,
-    FILTER_FIELD_RAW_FIELD_VALID,
-
-    FILTER_FIELD_RAW_FIELD_SELECT00 = 0x40,
-    FILTER_FIELD_RAW_FIELD_SELECT01,
-    FILTER_FIELD_RAW_FIELD_SELECT02,
-    FILTER_FIELD_RAW_FIELD_SELECT03,
-    FILTER_FIELD_RAW_FIELD_SELECT04,
-    FILTER_FIELD_RAW_FIELD_SELECT05,
-    FILTER_FIELD_RAW_FIELD_SELECT06,
-    FILTER_FIELD_RAW_FIELD_SELECT07,
-    FILTER_FIELD_RAW_FIELD_SELECT08,
-    FILTER_FIELD_RAW_FIELD_SELECT09,
-    FILTER_FIELD_RAW_FIELD_SELECT10,
-    FILTER_FIELD_RAW_FIELD_SELECT11,
-    FILTER_FIELD_RAW_FIELD_SELECT12,
-    FILTER_FIELD_RAW_FIELD_SELECT13,
-    FILTER_FIELD_RAW_FIELD_SELECT14,
-    FILTER_FIELD_RAW_FIELD_SELECT15,
-
-    FILTER_FIELD_RAW_END,
-} rtk_filter_field_type_raw_t;
-
-typedef enum rtk_filter_flag_care_type_e
-{
-    FILTER_FLAG_CARE_DONT_CARE = 0,
-    FILTER_FLAG_CARE_1,
-    FILTER_FLAG_CARE_0,
-    FILTER_FLAG_END
-} rtk_filter_flag_care_type_t;
-
-typedef rtk_uint32  rtk_filter_id_t;    /* filter id type */
-
-typedef enum rtk_filter_invert_e
-{
-    FILTER_INVERT_DISABLE = 0,
-    FILTER_INVERT_ENABLE,
-    FILTER_INVERT_END,
-} rtk_filter_invert_t;
-
-typedef rtk_uint32 rtk_filter_state_t;
-
-typedef rtk_uint32 rtk_filter_unmatch_action_t;
-
-typedef enum rtk_filter_unmatch_action_e
-{
-    FILTER_UNMATCH_DROP = 0,
-    FILTER_UNMATCH_PERMIT,
-    FILTER_UNMATCH_END,
-} rtk_filter_unmatch_action_type_t;
-
-typedef struct
-{
-    rtk_filter_field_t      *fieldHead;
-    rtk_filter_care_tag_t   careTag;
-    rtk_filter_activeport_t activeport;
-
-    rtk_filter_invert_t     invert;
-} rtk_filter_cfg_t;
-
-typedef struct
-{
-    rtk_filter_field_raw_t      dataFieldRaw[RTK_FILTER_RAW_FIELD_NUMBER];
-    rtk_filter_field_raw_t      careFieldRaw[RTK_FILTER_RAW_FIELD_NUMBER];
-    rtk_filter_field_type_raw_t fieldRawType[RTK_FILTER_RAW_FIELD_NUMBER];
-    rtk_filter_care_tag_t       careTag;
-    rtk_filter_activeport_t     activeport;
-
-    rtk_filter_invert_t         invert;
-    rtk_enable_t                valid;
-} rtk_filter_cfg_raw_t;
-
-typedef struct
-{
-    rtk_uint32 index;
-    rtk_filter_field_type_raw_t fieldType[RTK_FILTER_RAW_FIELD_NUMBER];
-} rtk_filter_template_t;
-
-typedef enum rtk_field_sel_e
-{
-    FORMAT_DEFAULT = 0,
-    FORMAT_RAW,
-    FORMAT_LLC,
-    FORMAT_IPV4,
-    FORMAT_ARP,
-    FORMAT_IPV6,
-    FORMAT_IPPAYLOAD,
-    FORMAT_L4PAYLOAD,
-    FORMAT_END
-}rtk_field_sel_t;
-
-typedef enum rtk_filter_iprange_e
-{
-    IPRANGE_UNUSED = 0,
-    IPRANGE_IPV4_SIP,
-    IPRANGE_IPV4_DIP,
-    IPRANGE_IPV6_SIP,
-    IPRANGE_IPV6_DIP,
-    IPRANGE_END
-}rtk_filter_iprange_t;
-
-typedef enum rtk_filter_vidrange_e
-{
-    VIDRANGE_UNUSED = 0,
-    VIDRANGE_CVID,
-    VIDRANGE_SVID,
-    VIDRANGE_END
-}rtk_filter_vidrange_t;
-
-typedef enum rtk_filter_portrange_e
-{
-    PORTRANGE_UNUSED = 0,
-    PORTRANGE_SPORT,
-    PORTRANGE_DPORT,
-    PORTRANGE_END
-}rtk_filter_portrange_t;
-
-/* Function Name:
- *      rtk_filter_igrAcl_init
- * Description:
- *      ACL initialization function
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Pointer pFilter_field or pFilter_cfg point to NULL.
- * Note:
- *      This function enable and intialize ACL function
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_init(void);
-
-/* Function Name:
- *      rtk_filter_igrAcl_field_add
- * Description:
- *      Add comparison rule to an ACL configuration
- * Input:
- *      pFilter_cfg     - The ACL configuration that this function will add comparison rule
- *      pFilter_field   - The comparison rule that will be added.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Pointer pFilter_field or pFilter_cfg point to NULL.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      This function add a comparison rule (*pFilter_field) to an ACL configuration (*pFilter_cfg).
- *      Pointer pFilter_cfg points to an ACL configuration structure, this structure keeps multiple ACL
- *      comparison rules by means of linked list. Pointer pFilter_field will be added to linked
- *      list keeped by structure that pFilter_cfg points to.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_field_add(rtk_filter_cfg_t *pFilter_cfg, rtk_filter_field_t *pFilter_field);
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_add
- * Description:
- *      Add an ACL configuration to ASIC
- * Input:
- *      filter_id       - Start index of ACL configuration.
- *      pFilter_cfg     - The ACL configuration that this function will add comparison rule
- *      pFilter_action  - Action(s) of ACL configuration.
- * Output:
- *      ruleNum - number of rules written in acl table
- * Return:
- *      RT_ERR_OK                               - OK
- *      RT_ERR_FAILED                           - Failed
- *      RT_ERR_SMI                              - SMI access error
- *      RT_ERR_NULL_POINTER                     - Pointer pFilter_field or pFilter_cfg point to NULL.
- *      RT_ERR_INPUT                            - Invalid input parameters.
- *      RT_ERR_ENTRY_INDEX                      - Invalid filter_id .
- *      RT_ERR_NULL_POINTER                     - Pointer pFilter_action or pFilter_cfg point to NULL.
- *      RT_ERR_FILTER_INACL_ACT_NOT_SUPPORT     - Action is not supported in this chip.
- *      RT_ERR_FILTER_INACL_RULE_NOT_SUPPORT    - Rule is not supported.
- * Note:
- *      This function store pFilter_cfg, pFilter_action into ASIC. The starting
- *      index(es) is filter_id.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_cfg_add(rtk_filter_id_t filter_id, rtk_filter_cfg_t *pFilter_cfg, rtk_filter_action_t *pAction, rtk_filter_number_t *ruleNum);
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_del
- * Description:
- *      Delete an ACL configuration from ASIC
- * Input:
- *      filter_id   - Start index of ACL configuration.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_ENTRYIDX  - Invalid filter_id.
- * Note:
- *      This function delete a group of ACL rules starting from filter_id.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_cfg_del(rtk_filter_id_t filter_id);
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_delAll
- * Description:
- *      Delete all ACL entries from ASIC
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      This function delete all ACL configuration from ASIC.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_cfg_delAll(void);
-
-/* Function Name:
- *      rtk_filter_igrAcl_cfg_get
- * Description:
- *      Get one ingress acl configuration from ASIC.
- * Input:
- *      filter_id       - Start index of ACL configuration.
- * Output:
- *      pFilter_cfg     - buffer pointer of ingress acl data
- *      pFilter_action  - buffer pointer of ingress acl action
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Pointer pFilter_action or pFilter_cfg point to NULL.
- *      RT_ERR_FILTER_ENTRYIDX  - Invalid entry index.
- * Note:
- *      This function delete all ACL configuration from ASIC.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_cfg_get(rtk_filter_id_t filter_id, rtk_filter_cfg_raw_t *pFilter_cfg, rtk_filter_action_t *pAction);
-
-/* Function Name:
- *      rtk_filter_igrAcl_unmatchAction_set
- * Description:
- *      Set action to packets when no ACL configuration match
- * Input:
- *      port    - Port id.
- *      action  - Action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function sets action of packets when no ACL configruation matches.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_unmatchAction_set(rtk_port_t port, rtk_filter_unmatch_action_t action);
-
-/* Function Name:
- *      rtk_filter_igrAcl_unmatchAction_get
- * Description:
- *      Get action to packets when no ACL configuration match
- * Input:
- *      port    - Port id.
- * Output:
- *      pAction - Action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function gets action of packets when no ACL configruation matches.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_unmatchAction_get(rtk_port_t port, rtk_filter_unmatch_action_t* action);
-
-/* Function Name:
- *      rtk_filter_igrAcl_state_set
- * Description:
- *      Set state of ingress ACL.
- * Input:
- *      port    - Port id.
- *      state   - Ingress ACL state.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function gets action of packets when no ACL configruation matches.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_state_set(rtk_port_t port, rtk_filter_state_t state);
-
-/* Function Name:
- *      rtk_filter_igrAcl_state_get
- * Description:
- *      Get state of ingress ACL.
- * Input:
- *      port    - Port id.
- * Output:
- *      pState  - Ingress ACL state.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port id.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This function gets action of packets when no ACL configruation matches.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_state_get(rtk_port_t port, rtk_filter_state_t* state);
-
-/* Function Name:
- *      rtk_filter_igrAcl_template_set
- * Description:
- *      Set template of ingress ACL.
- * Input:
- *      template - Ingress ACL template
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Invalid input parameters.
- * Note:
- *      This function set ACL template.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_template_set(rtk_filter_template_t *aclTemplate);
-
-/* Function Name:
- *      rtk_filter_igrAcl_template_get
- * Description:
- *      Get template of ingress ACL.
- * Input:
- *      template - Ingress ACL template
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This function gets template of ACL.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_template_get(rtk_filter_template_t *aclTemplate);
-
-/* Function Name:
- *      rtk_filter_igrAcl_field_sel_set
- * Description:
- *      Set user defined field selectors in HSB
- * Input:
- *      index       - index of field selector 0-15
- *      format      - Format of field selector
- *      offset      - Retrieving data offset
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      System support 16 user defined field selctors.
- *      Each selector can be enabled or disable.
- *      User can defined retrieving 16-bits in many predefiend
- *      standard l2/l3/l4 payload.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_field_sel_set(rtk_uint32 index, rtk_field_sel_t format, rtk_uint32 offset);
-
-/* Function Name:
- *      rtk_filter_igrAcl_field_sel_get
- * Description:
- *      Get user defined field selectors in HSB
- * Input:
- *      index       - index of field selector 0-15
- * Output:
- *      pFormat     - Format of field selector
- *      pOffset     - Retrieving data offset
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_filter_igrAcl_field_sel_get(rtk_uint32 index, rtk_field_sel_t *pFormat, rtk_uint32 *pOffset);
-
-/* Function Name:
- *      rtk_filter_iprange_set
- * Description:
- *      Set IP Range check
- * Input:
- *      index       - index of IP Range 0-15
- *      type        - IP Range check type, 0:Delete a entry, 1: IPv4_SIP, 2: IPv4_DIP, 3:IPv6_SIP, 4:IPv6_DIP
- *      upperIp     - The upper bound of IP range
- *      lowerIp     - The lower Bound of IP range
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      upperIp must be larger or equal than lowerIp.
- */
-extern rtk_api_ret_t rtk_filter_iprange_set(rtk_uint32 index, rtk_filter_iprange_t type, ipaddr_t upperIp, ipaddr_t lowerIp);
-
-/* Function Name:
- *      rtk_filter_iprange_get
- * Description:
- *      Set IP Range check
- * Input:
- *      index       - index of IP Range 0-15
- * Output:
- *      pType        - IP Range check type, 0:Delete a entry, 1: IPv4_SIP, 2: IPv4_DIP, 3:IPv6_SIP, 4:IPv6_DIP
- *      pUpperIp     - The upper bound of IP range
- *      pLowerIp     - The lower Bound of IP range
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- * Note:
- *      upperIp must be larger or equal than lowerIp.
- */
-extern rtk_api_ret_t rtk_filter_iprange_get(rtk_uint32 index, rtk_filter_iprange_t *pType, ipaddr_t *pUpperIp, ipaddr_t *pLowerIp);
-
-/* Function Name:
- *      rtk_filter_vidrange_set
- * Description:
- *      Set VID Range check
- * Input:
- *      index       - index of VID Range 0-15
- *      type        - IP Range check type, 0:Delete a entry, 1: CVID, 2: SVID
- *      upperVid    - The upper bound of VID range
- *      lowerVid    - The lower Bound of VID range
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      upperVid must be larger or equal than lowerVid.
- */
-extern rtk_api_ret_t rtk_filter_vidrange_set(rtk_uint32 index, rtk_filter_vidrange_t type, rtk_uint32 upperVid, rtk_uint32 lowerVid);
-
-/* Function Name:
- *      rtk_filter_vidrange_get
- * Description:
- *      Get VID Range check
- * Input:
- *      index       - index of VID Range 0-15
- * Output:
- *      pType        - IP Range check type, 0:Unused, 1: CVID, 2: SVID
- *      pUpperVid    - The upper bound of VID range
- *      pLowerVid    - The lower Bound of VID range
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_filter_vidrange_get(rtk_uint32 index, rtk_filter_vidrange_t *pType, rtk_uint32 *pUpperVid, rtk_uint32 *pLowerVid);
-
-/* Function Name:
- *      rtk_filter_portrange_set
- * Description:
- *      Set Port Range check
- * Input:
- *      index       - index of Port Range 0-15
- *      type        - IP Range check type, 0:Delete a entry, 1: Source Port, 2: Destnation Port
- *      upperPort   - The upper bound of Port range
- *      lowerPort   - The lower Bound of Port range
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      upperPort must be larger or equal than lowerPort.
- */
-extern rtk_api_ret_t rtk_filter_portrange_set(rtk_uint32 index, rtk_filter_portrange_t type, rtk_uint32 upperPort, rtk_uint32 lowerPort);
-
-/* Function Name:
- *      rtk_filter_portrange_get
- * Description:
- *      Set Port Range check
- * Input:
- *      index       - index of Port Range 0-15
- * Output:
- *      pType       - IP Range check type, 0:Delete a entry, 1: Source Port, 2: Destnation Port
- *      pUpperPort  - The upper bound of Port range
- *      pLowerPort  - The lower Bound of Port range
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_OUT_OF_RANGE    - The parameter is out of range
- *      RT_ERR_INPUT           - Input error
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_filter_portrange_get(rtk_uint32 index, rtk_filter_portrange_t *pType, rtk_uint32 *pUpperPort, rtk_uint32 *pLowerPort);
-
-/* Function Name:
- *      rtk_filter_igrAclPolarity_set
- * Description:
- *      Set ACL Goip control palarity
- * Input:
- *      polarity - 1: High, 0: Low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      none
- */
-extern rtk_api_ret_t rtk_filter_igrAclPolarity_set(rtk_uint32 polarity);
-
-/* Function Name:
- *      rtk_filter_igrAclPolarity_get
- * Description:
- *      Get ACL Goip control palarity
- * Input:
- *      pPolarity - 1: High, 0: Low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      none
- */
-extern rtk_api_ret_t rtk_filter_igrAclPolarity_get(rtk_uint32* pPolarity);
-
-
-#endif /* __RTK_API_ACL_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/cpu.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/cpu.h
deleted file mode 100644
index 5544aca7b2..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/cpu.h
+++ /dev/null
@@ -1,327 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes CPU module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_CPU_H__
-#define __RTK_API_CPU_H__
-
-
-/*
- * Data Type Declaration
- */
-typedef enum rtk_cpu_insert_e
-{
-    CPU_INSERT_TO_ALL = 0,
-    CPU_INSERT_TO_TRAPPING,
-    CPU_INSERT_TO_NONE,
-    CPU_INSERT_END
-}rtk_cpu_insert_t;
-
-typedef enum rtk_cpu_position_e
-{
-    CPU_POS_AFTER_SA = 0,
-    CPU_POS_BEFORE_CRC,
-    CPU_POS_END
-}rtk_cpu_position_t;
-
-typedef enum rtk_cpu_tag_length_e
-{
-    CPU_LEN_8BYTES = 0,
-    CPU_LEN_4BYTES,
-    CPU_LEN_END
-}rtk_cpu_tag_length_t;
-
-
-typedef enum rtk_cpu_rx_length_e
-{
-    CPU_RX_72BYTES = 0,
-    CPU_RX_64BYTES,
-    CPU_RX_END
-}rtk_cpu_rx_length_t;
-
-
-/* Function Name:
- *      rtk_cpu_enable_set
- * Description:
- *      Set CPU port function enable/disable.
- * Input:
- *      enable - CPU port function enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can set CPU port function enable/disable.
- */
-extern rtk_api_ret_t rtk_cpu_enable_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_cpu_enable_get
- * Description:
- *      Get CPU port and its setting.
- * Input:
- *      None
- * Output:
- *      pEnable - CPU port function enable
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_L2_NO_CPU_PORT   - CPU port is not exist
- * Note:
- *      The API can get CPU port function enable/disable.
- */
-extern rtk_api_ret_t rtk_cpu_enable_get(rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_cpu_tagPort_set
- * Description:
- *      Set CPU port and CPU tag insert mode.
- * Input:
- *      port - Port id.
- *      mode - CPU tag insert for packets egress from CPU port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can set CPU port and inserting proprietary CPU tag mode (Length/Type 0x8899)
- *      to the frame that transmitting to CPU port.
- *      The inset cpu tag mode is as following:
- *      - CPU_INSERT_TO_ALL
- *      - CPU_INSERT_TO_TRAPPING
- *      - CPU_INSERT_TO_NONE
- */
-extern rtk_api_ret_t rtk_cpu_tagPort_set(rtk_port_t port, rtk_cpu_insert_t mode);
-
-/* Function Name:
- *      rtk_cpu_tagPort_get
- * Description:
- *      Get CPU port and CPU tag insert mode.
- * Input:
- *      None
- * Output:
- *      pPort - Port id.
- *      pMode - CPU tag insert for packets egress from CPU port, 0:all insert 1:Only for trapped packets 2:no insert.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_L2_NO_CPU_PORT   - CPU port is not exist
- * Note:
- *      The API can get configured CPU port and its setting.
- *      The inset cpu tag mode is as following:
- *      - CPU_INSERT_TO_ALL
- *      - CPU_INSERT_TO_TRAPPING
- *      - CPU_INSERT_TO_NONE
- */
-extern rtk_api_ret_t rtk_cpu_tagPort_get(rtk_port_t *pPort, rtk_cpu_insert_t *pMode);
-
-/* Function Name:
- *      rtk_cpu_awarePort_set
- * Description:
- *      Set CPU aware port mask.
- * Input:
- *      portmask - Port mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK      - Invalid port mask.
- * Note:
- *      The API can set configured CPU aware port mask.
- */
-extern rtk_api_ret_t rtk_cpu_awarePort_set(rtk_portmask_t *pPortmask);
-
-
-/* Function Name:
- *      rtk_cpu_awarePort_get
- * Description:
- *      Get CPU aware port mask.
- * Input:
- *      None
- * Output:
- *      pPortmask - Port mask.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      The API can get configured CPU aware port mask.
- */
-extern rtk_api_ret_t rtk_cpu_awarePort_get(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_cpu_tagPosition_set
- * Description:
- *      Set CPU tag position.
- * Input:
- *      position - CPU tag position.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can set CPU tag position.
- */
-extern rtk_api_ret_t rtk_cpu_tagPosition_set(rtk_cpu_position_t position);
-
-/* Function Name:
- *      rtk_cpu_tagPosition_get
- * Description:
- *      Get CPU tag position.
- * Input:
- *      None
- * Output:
- *      pPosition - CPU tag position.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can get CPU tag position.
- */
-extern rtk_api_ret_t rtk_cpu_tagPosition_get(rtk_cpu_position_t *pPosition);
-
-/* Function Name:
- *      rtk_cpu_tagLength_set
- * Description:
- *      Set CPU tag length.
- * Input:
- *      length - CPU tag length.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can set CPU tag length.
- */
-extern rtk_api_ret_t rtk_cpu_tagLength_set(rtk_cpu_tag_length_t length);
-
-/* Function Name:
- *      rtk_cpu_tagLength_get
- * Description:
- *      Get CPU tag length.
- * Input:
- *      None
- * Output:
- *      pLength - CPU tag length.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can get CPU tag length.
- */
-extern rtk_api_ret_t rtk_cpu_tagLength_get(rtk_cpu_tag_length_t *pLength);
-
-/* Function Name:
- *      rtk_cpu_acceptLength_set
- * Description:
- *      Set CPU accept  length.
- * Input:
- *      length - CPU tag length.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can set CPU accept length.
- */
-extern rtk_api_ret_t rtk_cpu_acceptLength_set(rtk_cpu_rx_length_t length);
-
-/* Function Name:
- *      rtk_cpu_acceptLength_get
- * Description:
- *      Get CPU accept length.
- * Input:
- *      None
- * Output:
- *      pLength - CPU tag length.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT      - Invalid input.
- * Note:
- *      The API can get CPU accept length.
- */
-extern rtk_api_ret_t rtk_cpu_acceptLength_get(rtk_cpu_rx_length_t *pLength);
-
-/* Function Name:
- *      rtk_cpu_priRemap_set
- * Description:
- *      Configure CPU priorities mapping to internal absolute priority.
- * Input:
- *      int_pri     - internal priority value.
- *      new_pri    - new internal priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of CPU tag assignment for internal asic priority, and it is used for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_cpu_priRemap_set(rtk_pri_t int_pri, rtk_pri_t new_pri);
-
-/* Function Name:
- *      rtk_cpu_priRemap_get
- * Description:
- *      Configure CPU priorities mapping to internal absolute priority.
- * Input:
- *      int_pri     - internal priority value.
- * Output:
- *      pNew_pri    - new internal priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of CPU tag assignment for internal asic priority, and it is used for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_cpu_priRemap_get(rtk_pri_t int_pri, rtk_pri_t *pNew_pri);
-
-
-#endif /* __RTK_API_CPU_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/dot1x.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/dot1x.h
deleted file mode 100644
index ef0a05a04b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/dot1x.h
+++ /dev/null
@@ -1,470 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes 1X module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_DOT1X_H__
-#define __RTK_API_DOT1X_H__
-
-
-/* Type of port-based dot1x auth/unauth*/
-typedef enum rtk_dot1x_auth_status_e
-{
-    UNAUTH = 0,
-    AUTH,
-    AUTH_STATUS_END
-} rtk_dot1x_auth_status_t;
-
-typedef enum rtk_dot1x_direction_e
-{
-    DIR_BOTH = 0,
-    DIR_IN,
-    DIRECTION_END
-} rtk_dot1x_direction_t;
-
-/* unauth pkt action */
-typedef enum rtk_dot1x_unauth_action_e
-{
-    DOT1X_ACTION_DROP = 0,
-    DOT1X_ACTION_TRAP2CPU,
-    DOT1X_ACTION_GUESTVLAN,
-    DOT1X_ACTION_END
-} rtk_dot1x_unauth_action_t;
-
-/* Function Name:
- *      rtk_dot1x_unauthPacketOper_set
- * Description:
- *      Set 802.1x unauth action configuration.
- * Input:
- *      port            - Port id.
- *      unauth_action   - 802.1X unauth action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      This API can set 802.1x unauth action configuration.
- *      The unauth action is as following:
- *      - DOT1X_ACTION_DROP
- *      - DOT1X_ACTION_TRAP2CPU
- *      - DOT1X_ACTION_GUESTVLAN
- */
-extern rtk_api_ret_t rtk_dot1x_unauthPacketOper_set(rtk_port_t port, rtk_dot1x_unauth_action_t unauth_action);
-
-/* Function Name:
- *      rtk_dot1x_unauthPacketOper_get
- * Description:
- *      Get 802.1x unauth action configuration.
- * Input:
- *      port - Port id.
- * Output:
- *      pUnauth_action - 802.1X unauth action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get 802.1x unauth action configuration.
- *      The unauth action is as following:
- *      - DOT1X_ACTION_DROP
- *      - DOT1X_ACTION_TRAP2CPU
- *      - DOT1X_ACTION_GUESTVLAN
- */
-extern rtk_api_ret_t rtk_dot1x_unauthPacketOper_get(rtk_port_t port, rtk_dot1x_unauth_action_t *pUnauth_action);
-
-/* Function Name:
- *      rtk_dot1x_eapolFrame2CpuEnable_set
- * Description:
- *      Set 802.1x EAPOL packet trap to CPU configuration
- * Input:
- *      enable - The status of 802.1x EAPOL packet.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      To support 802.1x authentication functionality, EAPOL frame (ether type = 0x888E) has to
- *      be trapped to CPU.
- *      The status of EAPOL frame trap to CPU is as following:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_dot1x_eapolFrame2CpuEnable_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_dot1x_eapolFrame2CpuEnable_get
- * Description:
- *      Get 802.1x EAPOL packet trap to CPU configuration
- * Input:
- *      None
- * Output:
- *      pEnable - The status of 802.1x EAPOL packet.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      To support 802.1x authentication functionality, EAPOL frame (ether type = 0x888E) has to
- *      be trapped to CPU.
- *      The status of EAPOL frame trap to CPU is as following:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_dot1x_eapolFrame2CpuEnable_get(rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_dot1x_portBasedEnable_set
- * Description:
- *      Set 802.1x port-based enable configuration
- * Input:
- *      port - Port id.
- *      enable - The status of 802.1x port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_ENABLE               - Invalid enable input.
- *      RT_ERR_DOT1X_PORTBASEDPNEN  - 802.1X port-based enable error
- * Note:
- *      The API can update the port-based port enable register content. If a port is 802.1x
- *      port based network access control "enabled", it should be authenticated so packets
- *      from that port won't be dropped or trapped to CPU.
- *      The status of 802.1x port-based network access control is as following:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_dot1x_portBasedEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_dot1x_portBasedEnable_get
- * Description:
- *      Get 802.1x port-based enable configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - The status of 802.1x port.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get the 802.1x port-based port status.
- */
-extern rtk_api_ret_t rtk_dot1x_portBasedEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_dot1x_portBasedAuthStatus_set
- * Description:
- *      Set 802.1x port-based auth. port configuration
- * Input:
- *      port - Port id.
- *      port_auth - The status of 802.1x port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *     RT_ERR_DOT1X_PORTBASEDAUTH   - 802.1X port-based auth error
- * Note:
- *      The authenticated status of 802.1x port-based network access control is as following:
- *      - UNAUTH
- *      - AUTH
- */
-extern rtk_api_ret_t rtk_dot1x_portBasedAuthStatus_set(rtk_port_t port, rtk_dot1x_auth_status_t port_auth);
-
-/* Function Name:
- *      rtk_dot1x_portBasedAuthStatus_get
- * Description:
- *      Get 802.1x port-based auth. port configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pPort_auth - The status of 802.1x port.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get 802.1x port-based port auth.information.
- */
-extern rtk_api_ret_t rtk_dot1x_portBasedAuthStatus_get(rtk_port_t port, rtk_dot1x_auth_status_t *pPort_auth);
-
-/* Function Name:
- *      rtk_dot1x_portBasedDirection_set
- * Description:
- *      Set 802.1x port-based operational direction configuration
- * Input:
- *      port            - Port id.
- *      port_direction  - Operation direction
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_DOT1X_PORTBASEDOPDIR - 802.1X port-based operation direction error
- * Note:
- *      The operate controlled direction of 802.1x port-based network access control is as following:
- *      - BOTH
- *      - IN
- */
-extern rtk_api_ret_t rtk_dot1x_portBasedDirection_set(rtk_port_t port, rtk_dot1x_direction_t port_direction);
-
-/* Function Name:
- *      rtk_dot1x_portBasedDirection_get
- * Description:
- *      Get 802.1X port-based operational direction configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pPort_direction - Operation direction
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get 802.1x port-based operational direction information.
- */
-extern rtk_api_ret_t rtk_dot1x_portBasedDirection_get(rtk_port_t port, rtk_dot1x_direction_t *pPort_direction);
-
-/* Function Name:
- *      rtk_dot1x_macBasedEnable_set
- * Description:
- *      Set 802.1x mac-based port enable configuration
- * Input:
- *      port - Port id.
- *      enable - The status of 802.1x port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_ENABLE               - Invalid enable input.
- *      RT_ERR_DOT1X_MACBASEDPNEN   - 802.1X mac-based enable error
- * Note:
- *      If a port is 802.1x MAC based network access control "enabled", the incoming packets should
- *       be authenticated so packets from that port won't be dropped or trapped to CPU.
- *      The status of 802.1x MAC-based network access control is as following:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_dot1x_macBasedEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_dot1x_macBasedEnable_get
- * Description:
- *      Get 802.1x mac-based port enable configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - The status of 802.1x port.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      If a port is 802.1x MAC based network access control "enabled", the incoming packets should
- *      be authenticated so packets from that port wont be dropped or trapped to CPU.
- *      The status of 802.1x MAC-based network access control is as following:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_dot1x_macBasedEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_dot1x_macBasedAuthMac_add
- * Description:
- *      Add an authenticated MAC to ASIC
- * Input:
- *      port        - Port id.
- *      pAuth_mac   - The authenticated MAC.
- *      fid         - filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_ENABLE               - Invalid enable input.
- *      RT_ERR_DOT1X_MACBASEDPNEN   - 802.1X mac-based enable error
- * Note:
- *      The API can add a 802.1x authenticated MAC address to port. If the MAC does not exist in LUT,
- *      user can't add this MAC to auth status.
- */
-extern rtk_api_ret_t rtk_dot1x_macBasedAuthMac_add(rtk_port_t port, rtk_mac_t *pAuth_mac, rtk_fid_t fid);
-
-/* Function Name:
- *      rtk_dot1x_macBasedAuthMac_del
- * Description:
- *      Delete an authenticated MAC to ASIC
- * Input:
- *      port - Port id.
- *      pAuth_mac - The authenticated MAC.
- *      fid - filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_MAC          - Invalid MAC address.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can delete a 802.1x authenticated MAC address to port. It only change the auth status of
- *      the MAC and won't delete it from LUT.
- */
-extern rtk_api_ret_t rtk_dot1x_macBasedAuthMac_del(rtk_port_t port, rtk_mac_t *pAuth_mac, rtk_fid_t fid);
-
-/* Function Name:
- *      rtk_dot1x_macBasedDirection_set
- * Description:
- *      Set 802.1x mac-based operational direction configuration
- * Input:
- *      mac_direction - Operation direction
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter.
- *      RT_ERR_DOT1X_MACBASEDOPDIR  - 802.1X mac-based operation direction error
- * Note:
- *      The operate controlled direction of 802.1x mac-based network access control is as following:
- *      - BOTH
- *      - IN
- */
-extern rtk_api_ret_t rtk_dot1x_macBasedDirection_set(rtk_dot1x_direction_t mac_direction);
-
-/* Function Name:
- *      rtk_dot1x_macBasedDirection_get
- * Description:
- *      Get 802.1x mac-based operational direction configuration
- * Input:
- *      port - Port id.
- * Output:
- *      pMac_direction - Operation direction
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get 802.1x mac-based operational direction information.
- */
-extern rtk_api_ret_t rtk_dot1x_macBasedDirection_get(rtk_dot1x_direction_t *pMac_direction);
-
-/* Function Name:
- *      Set 802.1x guest VLAN configuration
- * Description:
- *      Set 802.1x mac-based operational direction configuration
- * Input:
- *      vid - 802.1x guest VLAN ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The operate controlled 802.1x guest VLAN
- */
-extern rtk_api_ret_t rtk_dot1x_guestVlan_set(rtk_vlan_t vid);
-
-/* Function Name:
- *      rtk_dot1x_guestVlan_get
- * Description:
- *      Get 802.1x guest VLAN configuration
- * Input:
- *      None
- * Output:
- *      pVid - 802.1x guest VLAN ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get 802.1x guest VLAN information.
- */
-extern rtk_api_ret_t rtk_dot1x_guestVlan_get(rtk_vlan_t *pVid);
-
-/* Function Name:
- *      rtk_dot1x_guestVlan2Auth_set
- * Description:
- *      Set 802.1x guest VLAN to auth host configuration
- * Input:
- *      enable - The status of guest VLAN to auth host.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The operational direction of 802.1x guest VLAN to auth host control is as following:
- *      - ENABLED
- *      - DISABLED
- */
-extern rtk_api_ret_t rtk_dot1x_guestVlan2Auth_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_dot1x_guestVlan2Auth_get
- * Description:
- *      Get 802.1x guest VLAN to auth host configuration
- * Input:
- *      None
- * Output:
- *      pEnable - The status of guest VLAN to auth host.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get 802.1x guest VLAN to auth host information.
- */
-extern rtk_api_ret_t rtk_dot1x_guestVlan2Auth_get(rtk_enable_t *pEnable);
-
-
-#endif /* __RTK_API_DOT1X_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/eee.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/eee.h
deleted file mode 100644
index b670998c8c..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/eee.h
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes EEE module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_EEE_H__
-#define __RTK_API_EEE_H__
-
-/* Function Name:
- *      rtk_eee_init
- * Description:
- *      EEE function initialization.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API is used to initialize EEE status.
- */
-extern rtk_api_ret_t rtk_eee_init(void);
-
-/* Function Name:
- *      rtk_eee_portEnable_set
- * Description:
- *      Set enable status of EEE function.
- * Input:
- *      port - port id.
- *      enable - enable EEE status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_ID - Invalid port number.
- *      RT_ERR_ENABLE - Invalid enable input.
- * Note:
- *      This API can set EEE function to the specific port.
- *      The configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_eee_portEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_eee_portEnable_get
- * Description:
- *      Get port admin configuration of the specific port.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Back pressure status.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_ID - Invalid port number.
- * Note:
- *      This API can set EEE function to the specific port.
- *      The configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_eee_portEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-
-#endif /* __RTK_API_EEE_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/i2c.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/i2c.h
deleted file mode 100644
index 2c7f0756ae..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/i2c.h
+++ /dev/null
@@ -1,168 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes I2C module high-layer API defination
- *
- */
-
-
-#ifndef __RTK_API_I2C_H__
-#define __RTK_API_I2C_H__
-#include <rtk_types.h>
-
-#define I2C_GPIO_MAX_GROUP (3)
-
-typedef enum rtk_I2C_16bit_mode_e{
-    I2C_LSB_16BIT_MODE = 0,
-    I2C_70B_LSB_16BIT_MODE,
-    I2C_Mode_END
-}rtk_I2C_16bit_mode_t;
-
-
-typedef enum rtk_I2C_gpio_pin_e{
-    I2C_GPIO_PIN_8_9 = 0,
-    I2C_GPIO_PIN_15_16 ,
-    I2C_GPIO_PIN_35_36 ,
-    I2C_GPIO_PIN_END
-}rtk_I2C_gpio_pin_t;
-
-
-/* Function Name:
- *      rtk_i2c_data_read
- * Description:
- *      read i2c slave device register.
- * Input:
- *      deviceAddr   -   access Slave device address
- *      slaveRegAddr -   access Slave register address
- * Output:
- *      pRegData     -   read data
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_NULL_POINTER     - input parameter is null pointer
- * Note:
- *      The API can access i2c slave and read i2c slave device register.
- */
-extern rtk_api_ret_t rtk_i2c_data_read(rtk_uint8 deviceAddr, rtk_uint32 slaveRegAddr, rtk_uint32 *pRegData);
-
-/* Function Name:
- *      rtk_i2c_data_write
- * Description:
- *      write data to i2c slave device register
- * Input:
- *      deviceAddr   -   access Slave device address
- *      slaveRegAddr -   access Slave register address
- *      regData      -   data to set
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- * Note:
- *      The API can access i2c slave and setting i2c slave device register.
- */
-extern rtk_api_ret_t rtk_i2c_data_write(rtk_uint8 deviceAddr, rtk_uint32 slaveRegAddr, rtk_uint32 regData);
-
-
-/* Function Name:
- *      rtk_i2c_init
- * Description:
- *      I2C smart function initialization.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- * Note:
- *      This API is used to initialize EEE status.
- *      need used GPIO pins
- *      OpenDrain and clock
- */
-extern rtk_api_ret_t rtk_i2c_init(void);
-
-/* Function Name:
- *      rtk_i2c_mode_set
- * Description:
- *      Set I2C data byte-order.
- * Input:
- *      i2cmode - byte-order mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      This API can set I2c traffic's byte-order .
- */
-extern rtk_api_ret_t rtk_i2c_mode_set( rtk_I2C_16bit_mode_t i2cmode);
-
-/* Function Name:
- *      rtk_i2c_mode_get
- * Description:
- *      Get i2c traffic byte-order setting.
- * Input:
- *      None
- * Output:
- *      pI2cMode - i2c byte-order
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_NULL_POINTER     - input parameter is null pointer
- * Note:
- *      The API can get i2c traffic byte-order setting.
- */
-extern rtk_api_ret_t rtk_i2c_mode_get( rtk_I2C_16bit_mode_t * pI2cMode);
-
-
-/* Function Name:
- *      rtk_i2c_gpioPinGroup_set
- * Description:
- *      Set i2c SDA & SCL used GPIO pins group.
- * Input:
- *      pins_group - GPIO pins group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The API can set i2c used gpio pins group.
- *      There are three group pins could be used
- */
-extern rtk_api_ret_t rtk_i2c_gpioPinGroup_set( rtk_I2C_gpio_pin_t pins_group);
-
-/* Function Name:
- *      rtk_i2c_gpioPinGroup_get
- * Description:
- *      Get i2c SDA & SCL used GPIO pins group.
- * Input:
- *      None
- * Output:
- *      pPins_group - GPIO pins group
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_NULL_POINTER     - input parameter is null pointer
- * Note:
- *      The API can get i2c used gpio pins group.
- *      There are three group pins could be used
- */
-extern rtk_api_ret_t rtk_i2c_gpioPinGroup_get(rtk_I2C_gpio_pin_t * pPins_group);
-
-
-
-
-
-
-
-#endif
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/igmp.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/igmp.h
deleted file mode 100644
index f088b0ccdd..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/igmp.h
+++ /dev/null
@@ -1,769 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes IGMP module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_IGMP_H__
-#define __RTK_API_IGMP_H__
-
-/*
- * Data Type Declaration
- */
-typedef enum rtk_igmp_type_e
-{
-    IGMP_IPV4 = 0,
-    IGMP_PPPOE_IPV4,
-    IGMP_MLD,
-    IGMP_PPPOE_MLD,
-    IGMP_TYPE_END
-} rtk_igmp_type_t;
-
-typedef enum rtk_trap_igmp_action_e
-{
-    IGMP_ACTION_FORWARD = 0,
-    IGMP_ACTION_TRAP2CPU,
-    IGMP_ACTION_DROP,
-    IGMP_ACTION_ASIC,
-    IGMP_ACTION_END
-} rtk_igmp_action_t;
-
-typedef enum rtk_igmp_protocol_e
-{
-    PROTOCOL_IGMPv1 = 0,
-    PROTOCOL_IGMPv2,
-    PROTOCOL_IGMPv3,
-    PROTOCOL_MLDv1,
-    PROTOCOL_MLDv2,
-    PROTOCOL_END
-} rtk_igmp_protocol_t;
-
-typedef enum rtk_igmp_tableFullAction_e
-{
-    IGMP_TABLE_FULL_FORWARD = 0,
-    IGMP_TABLE_FULL_DROP,
-    IGMP_TABLE_FULL_TRAP,
-    IGMP_TABLE_FULL_OP_END
-}rtk_igmp_tableFullAction_t;
-
-typedef enum rtk_igmp_checksumErrorAction_e
-{
-    IGMP_CRC_ERR_DROP = 0,
-    IGMP_CRC_ERR_TRAP,
-    IGMP_CRC_ERR_FORWARD,
-    IGMP_CRC_ERR_OP_END
-}rtk_igmp_checksumErrorAction_t;
-
-typedef enum rtk_igmp_bypassGroup_e
-{
-    IGMP_BYPASS_224_0_0_X = 0,
-    IGMP_BYPASS_224_0_1_X,
-    IGMP_BYPASS_239_255_255_X,
-    IGMP_BYPASS_IPV6_00XX,
-    IGMP_BYPASS_GROUP_END
-}rtk_igmp_bypassGroup_t;
-
-
-typedef struct rtk_igmp_dynamicRouterPort_s
-{
-    rtk_enable_t    dynamicRouterPort0Valid;
-    rtk_port_t      dynamicRouterPort0;
-    rtk_uint32      dynamicRouterPort0Timer;
-    rtk_enable_t    dynamicRouterPort1Valid;
-    rtk_port_t      dynamicRouterPort1;
-    rtk_uint32      dynamicRouterPort1Timer;
-
-}rtk_igmp_dynamicRouterPort_t;
-
-typedef struct rtk_igmp_rxPktEnable_s
-{
-    rtk_enable_t rxQuery;
-    rtk_enable_t rxReport;
-    rtk_enable_t rxLeave;
-    rtk_enable_t rxMRP;
-    rtk_enable_t rxMcast;
-}rtk_igmp_rxPktEnable_t;
-
-typedef struct rtk_igmp_groupInfo_s
-{
-    rtk_enable_t    valid;
-    rtk_portmask_t  member;
-    rtk_uint32      timer[RTK_PORT_MAX];
-    rtk_uint32      reportSuppFlag;
-}rtk_igmp_groupInfo_t;
-
-typedef enum rtk_igmp_ReportLeaveFwdAct_e
-{
-    IGMP_REPORT_LEAVE_TO_ROUTER = 0,
-    IGMP_REPORT_LEAVE_TO_ALLPORT,
-    IGMP_REPORT_LEAVE_TO_ROUTER_PORT_ADV,
-    IGMP_REPORT_LEAVE_ACT_END
-}rtk_igmp_ReportLeaveFwdAct_t;
-
-/* Function Name:
- *      rtk_igmp_init
- * Description:
- *      This API enables H/W IGMP and set a default initial configuration.
- * Input:
- *      None.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API enables H/W IGMP and set a default initial configuration.
- */
-extern rtk_api_ret_t rtk_igmp_init(void);
-
-/* Function Name:
- *      rtk_igmp_state_set
- * Description:
- *      This API set H/W IGMP state.
- * Input:
- *      enabled     - H/W IGMP state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set H/W IGMP state.
- */
-extern rtk_api_ret_t rtk_igmp_state_set(rtk_enable_t enabled);
-
-/* Function Name:
- *      rtk_igmp_state_get
- * Description:
- *      This API get H/W IGMP state.
- * Input:
- *      None.
- * Output:
- *      pEnabled        - H/W IGMP state
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set current H/W IGMP state.
- */
-extern rtk_api_ret_t rtk_igmp_state_get(rtk_enable_t *pEnabled);
-
-/* Function Name:
- *      rtk_igmp_static_router_port_set
- * Description:
- *      Configure static router port
- * Input:
- *      pPortmask    - Static Port mask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API set static router port
- */
-extern rtk_api_ret_t rtk_igmp_static_router_port_set(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_igmp_static_router_port_get
- * Description:
- *      Get static router port
- * Input:
- *      None.
- * Output:
- *      pPortmask       - Static port mask
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API get static router port
- */
-extern rtk_api_ret_t rtk_igmp_static_router_port_get(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_igmp_protocol_set
- * Description:
- *      set IGMP/MLD protocol action
- * Input:
- *      port        - Port ID
- *      protocol    - IGMP/MLD protocol
- *      action      - Per-port and per-protocol IGMP action seeting
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API set IGMP/MLD protocol action
- */
-extern rtk_api_ret_t rtk_igmp_protocol_set(rtk_port_t port, rtk_igmp_protocol_t protocol, rtk_igmp_action_t action);
-
-/* Function Name:
- *      rtk_igmp_protocol_get
- * Description:
- *      set IGMP/MLD protocol action
- * Input:
- *      port        - Port ID
- *      protocol    - IGMP/MLD protocol
- *      action      - Per-port and per-protocol IGMP action seeting
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *      This API set IGMP/MLD protocol action
- */
-extern rtk_api_ret_t rtk_igmp_protocol_get(rtk_port_t port, rtk_igmp_protocol_t protocol, rtk_igmp_action_t *pAction);
-
-/* Function Name:
- *      rtk_igmp_fastLeave_set
- * Description:
- *      set IGMP/MLD FastLeave state
- * Input:
- *      state       - ENABLED: Enable FastLeave, DISABLED: disable FastLeave
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API set IGMP/MLD FastLeave state
- */
-extern rtk_api_ret_t rtk_igmp_fastLeave_set(rtk_enable_t state);
-
-/* Function Name:
- *      rtk_igmp_fastLeave_get
- * Description:
- *      get IGMP/MLD FastLeave state
- * Input:
- *      None
- * Output:
- *      pState      - ENABLED: Enable FastLeave, DISABLED: disable FastLeave
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - NULL pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API get IGMP/MLD FastLeave state
- */
-extern rtk_api_ret_t rtk_igmp_fastLeave_get(rtk_enable_t *pState);
-
-/* Function Name:
- *      rtk_igmp_maxGroup_set
- * Description:
- *      Set per port multicast group learning limit.
- * Input:
- *      port        - Port ID
- *      group       - The number of multicast group learning limit.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_PORT_ID         - Error Port ID
- *      RT_ERR_OUT_OF_RANGE    - parameter out of range
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API set per port multicast group learning limit.
- */
-extern rtk_api_ret_t rtk_igmp_maxGroup_set(rtk_port_t port, rtk_uint32 group);
-
-/* Function Name:
- *      rtk_igmp_maxGroup_get
- * Description:
- *      Get per port multicast group learning limit.
- * Input:
- *      port        - Port ID
- * Output:
- *      pGroup      - The number of multicast group learning limit.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_PORT_ID         - Error Port ID
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API get per port multicast group learning limit.
- */
-extern rtk_api_ret_t rtk_igmp_maxGroup_get(rtk_port_t port, rtk_uint32 *pGroup);
-
-/* Function Name:
- *      rtk_igmp_currentGroup_get
- * Description:
- *      Get per port multicast group learning count.
- * Input:
- *      port        - Port ID
- * Output:
- *      pGroup      - The number of multicast group learning count.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_PORT_ID         - Error Port ID
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API get per port multicast group learning count.
- */
-extern rtk_api_ret_t rtk_igmp_currentGroup_get(rtk_port_t port, rtk_uint32 *pGroup);
-
-/* Function Name:
- *      rtk_igmp_tableFullAction_set
- * Description:
- *      set IGMP/MLD Table Full Action
- * Input:
- *      action      - Table Full Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_tableFullAction_set(rtk_igmp_tableFullAction_t action);
-
-/* Function Name:
- *      rtk_igmp_tableFullAction_get
- * Description:
- *      get IGMP/MLD Table Full Action
- * Input:
- *      None
- * Output:
- *      pAction     - Table Full Action
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_tableFullAction_get(rtk_igmp_tableFullAction_t *pAction);
-
-/* Function Name:
- *      rtk_igmp_checksumErrorAction_set
- * Description:
- *      set IGMP/MLD Checksum Error Action
- * Input:
- *      action      - Checksum error Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_checksumErrorAction_set(rtk_igmp_checksumErrorAction_t action);
-
-/* Function Name:
- *      rtk_igmp_checksumErrorAction_get
- * Description:
- *      get IGMP/MLD Checksum Error Action
- * Input:
- *      None
- * Output:
- *      pAction     - Checksum error Action
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_checksumErrorAction_get(rtk_igmp_checksumErrorAction_t *pAction);
-
-/* Function Name:
- *      rtk_igmp_leaveTimer_set
- * Description:
- *      set IGMP/MLD Leave timer
- * Input:
- *      timer       - Leave timer
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_leaveTimer_set(rtk_uint32 timer);
-
-/* Function Name:
- *      rtk_igmp_leaveTimer_get
- * Description:
- *      get IGMP/MLD Leave timer
- * Input:
- *      None
- * Output:
- *      pTimer      - Leave Timer.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_leaveTimer_get(rtk_uint32 *pTimer);
-
-/* Function Name:
- *      rtk_igmp_queryInterval_set
- * Description:
- *      set IGMP/MLD Query Interval
- * Input:
- *      interval     - Query Interval
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_queryInterval_set(rtk_uint32 interval);
-
-/* Function Name:
- *      rtk_igmp_queryInterval_get
- * Description:
- *      get IGMP/MLD Query Interval
- * Input:
- *      None.
- * Output:
- *      pInterval   - Query Interval
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_queryInterval_get(rtk_uint32 *pInterval);
-
-/* Function Name:
- *      rtk_igmp_robustness_set
- * Description:
- *      set IGMP/MLD Robustness value
- * Input:
- *      robustness     - Robustness value
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_robustness_set(rtk_uint32 robustness);
-
-/* Function Name:
- *      rtk_igmp_robustness_get
- * Description:
- *      get IGMP/MLD Robustness value
- * Input:
- *      None
- * Output:
- *      pRobustness     - Robustness value.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_igmp_robustness_get(rtk_uint32 *pRobustness);
-
-/* Function Name:
- *      rtk_igmp_dynamicRouterRortAllow_set
- * Description:
- *      Configure dynamic router port allow option
- * Input:
- *      pPortmask    - Dynamic Port allow mask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_dynamicRouterPortAllow_set(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_igmp_dynamicRouterRortAllow_get
- * Description:
- *      Get dynamic router port allow option
- * Input:
- *      None.
- * Output:
- *      pPortmask    - Dynamic Port allow mask
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_dynamicRouterPortAllow_get(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_igmp_dynamicRouterPort_get
- * Description:
- *      Get dynamic router port
- * Input:
- *      None.
- * Output:
- *      pDynamicRouterPort    - Dynamic Router Port
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_NULL_POINTER    - Null pointer
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_PORT_MASK       - Error parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_dynamicRouterPort_get(rtk_igmp_dynamicRouterPort_t *pDynamicRouterPort);
-
-/* Function Name:
- *      rtk_igmp_suppressionEnable_set
- * Description:
- *      Configure IGMPv1/v2 & MLDv1 Report/Leave/Done suppression
- * Input:
- *      reportSuppression   - Report suppression
- *      leaveSuppression    - Leave suppression
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_suppressionEnable_set(rtk_enable_t reportSuppression, rtk_enable_t leaveSuppression);
-
-/* Function Name:
- *      rtk_igmp_suppressionEnable_get
- * Description:
- *      Get IGMPv1/v2 & MLDv1 Report/Leave/Done suppression
- * Input:
- *      None
- * Output:
- *      pReportSuppression  - Report suppression
- *      pLeaveSuppression   - Leave suppression
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_suppressionEnable_get(rtk_enable_t *pReportSuppression, rtk_enable_t *pLeaveSuppression);
-
-/* Function Name:
- *      rtk_igmp_portRxPktEnable_set
- * Description:
- *      Configure IGMP/MLD RX Packet configuration
- * Input:
- *      port       - Port ID
- *      pRxCfg     - RX Packet Configuration
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_portRxPktEnable_set(rtk_port_t port, rtk_igmp_rxPktEnable_t *pRxCfg);
-
-/* Function Name:
- *      rtk_igmp_portRxPktEnable_get
- * Description:
- *      Get IGMP/MLD RX Packet configuration
- * Input:
- *      port       - Port ID
- *      pRxCfg     - RX Packet Configuration
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_portRxPktEnable_get(rtk_port_t port, rtk_igmp_rxPktEnable_t *pRxCfg);
-
-/* Function Name:
- *      rtk_igmp_groupInfo_get
- * Description:
- *      Get IGMP/MLD Group database
- * Input:
- *      indes       - Index (0~255)
- * Output:
- *      pGroup      - Group database information.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_groupInfo_get(rtk_uint32 index, rtk_igmp_groupInfo_t *pGroup);
-
-/* Function Name:
- *      rtk_igmp_ReportLeaveFwdAction_set
- * Description:
- *      Set Report Leave packet forwarding action
- * Input:
- *      action      - Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_ReportLeaveFwdAction_set(rtk_igmp_ReportLeaveFwdAct_t action);
-
-/* Function Name:
- *      rtk_igmp_ReportLeaveFwdAction_get
- * Description:
- *      Get Report Leave packet forwarding action
- * Input:
- *      action      - Action
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null Pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_ReportLeaveFwdAction_get(rtk_igmp_ReportLeaveFwdAct_t *pAction);
-
-/* Function Name:
- *      rtk_igmp_dropLeaveZeroEnable_set
- * Description:
- *      Set the function of droppping Leave packet with group IP = 0.0.0.0
- * Input:
- *      enabled      - Action 1: drop, 0:pass
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_dropLeaveZeroEnable_set(rtk_enable_t enabled);
-
-/* Function Name:
- *      rtk_igmp_dropLeaveZeroEnable_get
- * Description:
- *      Get the function of droppping Leave packet with group IP = 0.0.0.0
- * Input:
- *      None
- * Output:
- *      pEnabled.   - Action 1: drop, 0:pass
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null Pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_dropLeaveZeroEnable_get(rtk_enable_t *pEnabled);
-
-/* Function Name:
- *      rtk_igmp_bypassGroupRange_set
- * Description:
- *      Set Bypass group
- * Input:
- *      group       - bypassed group
- *      enabled     - enabled 1: Bypassed, 0: not bypass
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_bypassGroupRange_set(rtk_igmp_bypassGroup_t group, rtk_enable_t enabled);
-
-/* Function Name:
- *      rtk_igmp_bypassGroupRange_get
- * Description:
- *      get Bypass group
- * Input:
- *      group       - bypassed group
- * Output:
- *      pEnable     - enabled 1: Bypassed, 0: not bypass
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error Input
- *      RT_ERR_NULL_POINTER    - Null Pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_igmp_bypassGroupRange_get(rtk_igmp_bypassGroup_t group, rtk_enable_t *pEnable);
-
-#endif /* __RTK_API_IGMP_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/interrupt.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/interrupt.h
deleted file mode 100644
index f2689ebc70..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/interrupt.h
+++ /dev/null
@@ -1,254 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes Interrupt module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_INTERRUPT_H__
-#define __RTK_API_INTERRUPT_H__
-
-
-/*
- * Data Type Declaration
- */
-#define RTK_MAX_NUM_OF_INTERRUPT_TYPE               1
-
-
-typedef struct  rtk_int_status_s
-{
-    rtk_uint16 value[RTK_MAX_NUM_OF_INTERRUPT_TYPE];
-} rtk_int_status_t;
-
-typedef struct rtk_int_info_s
-{
-    rtk_portmask_t  portMask;
-    rtk_uint32      meterMask;
-    rtk_uint32      systemLearnOver;
-}rtk_int_info_t;
-
-typedef enum rtk_int_type_e
-{
-    INT_TYPE_LINK_STATUS = 0,
-    INT_TYPE_METER_EXCEED,
-    INT_TYPE_LEARN_LIMIT,
-    INT_TYPE_LINK_SPEED,
-    INT_TYPE_CONGEST,
-    INT_TYPE_GREEN_FEATURE,
-    INT_TYPE_LOOP_DETECT,
-    INT_TYPE_8051,
-    INT_TYPE_CABLE_DIAG,
-    INT_TYPE_ACL,
-    INT_TYPE_RESERVED, /* Unused */
-    INT_TYPE_SLIENT,
-    INT_TYPE_END
-}rtk_int_type_t;
-
-typedef enum rtk_int_advType_e
-{
-    ADV_L2_LEARN_PORT_MASK = 0,
-    ADV_SPEED_CHANGE_PORT_MASK,
-    ADV_SPECIAL_CONGESTION_PORT_MASK,
-    ADV_PORT_LINKDOWN_PORT_MASK,
-    ADV_PORT_LINKUP_PORT_MASK,
-    ADV_METER_EXCEED_MASK,
-    ADV_RLDP_LOOPED,
-    ADV_RLDP_RELEASED,
-    ADV_END,
-} rtk_int_advType_t;
-
-typedef enum rtk_int_polarity_e
-{
-    INT_POLAR_HIGH = 0,
-    INT_POLAR_LOW,
-    INT_POLAR_END
-} rtk_int_polarity_t;
-
-/* Function Name:
- *      rtk_int_polarity_set
- * Description:
- *      Set interrupt polarity configuration.
- * Input:
- *      type - Interruptpolarity type.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set interrupt polarity configuration.
- */
-extern rtk_api_ret_t rtk_int_polarity_set(rtk_int_polarity_t type);
-
-/* Function Name:
- *      rtk_int_polarity_get
- * Description:
- *      Get interrupt polarity configuration.
- * Input:
- *      None
- * Output:
- *      pType - Interruptpolarity type.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API can get interrupt polarity configuration.
- */
-extern rtk_api_ret_t rtk_int_polarity_get(rtk_int_polarity_t *pType);
-
-/* Function Name:
- *      rtk_int_control_set
- * Description:
- *      Set interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- *      enable - Interrupt status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The API can set interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS
- *      - INT_TYPE_METER_EXCEED
- *      - INT_TYPE_LEARN_LIMIT
- *      - INT_TYPE_LINK_SPEED
- *      - INT_TYPE_CONGEST
- *      - INT_TYPE_GREEN_FEATURE
- *      - INT_TYPE_LOOP_DETECT
- *      - INT_TYPE_8051,
- *      - INT_TYPE_CABLE_DIAG,
- *      - INT_TYPE_ACL,
- *      - INT_TYPE_SLIENT
- */
-extern rtk_api_ret_t rtk_int_control_set(rtk_int_type_t type, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_int_control_get
- * Description:
- *      Get interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- * Output:
- *      pEnable - Interrupt status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS
- *      - INT_TYPE_METER_EXCEED
- *      - INT_TYPE_LEARN_LIMIT
- *      - INT_TYPE_LINK_SPEED
- *      - INT_TYPE_CONGEST
- *      - INT_TYPE_GREEN_FEATURE
- *      - INT_TYPE_LOOP_DETECT
- *      - INT_TYPE_8051,
- *      - INT_TYPE_CABLE_DIAG,
- *      - INT_TYPE_ACL,
- *      - INT_TYPE_SLIENT
- */
-extern rtk_api_ret_t rtk_int_control_get(rtk_int_type_t type, rtk_enable_t* pEnable);
-
-/* Function Name:
- *      rtk_int_status_set
- * Description:
- *      Set interrupt trigger status to clean.
- * Input:
- *      None
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- * Note:
- *      The API can clean interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS    (value[0] (Bit0))
- *      - INT_TYPE_METER_EXCEED   (value[0] (Bit1))
- *      - INT_TYPE_LEARN_LIMIT    (value[0] (Bit2))
- *      - INT_TYPE_LINK_SPEED     (value[0] (Bit3))
- *      - INT_TYPE_CONGEST        (value[0] (Bit4))
- *      - INT_TYPE_GREEN_FEATURE  (value[0] (Bit5))
- *      - INT_TYPE_LOOP_DETECT    (value[0] (Bit6))
- *      - INT_TYPE_8051           (value[0] (Bit7))
- *      - INT_TYPE_CABLE_DIAG     (value[0] (Bit8))
- *      - INT_TYPE_ACL            (value[0] (Bit9))
- *      - INT_TYPE_SLIENT         (value[0] (Bit11))
- *      The status will be cleared after execute this API.
- */
-extern rtk_api_ret_t rtk_int_status_set(rtk_int_status_t *pStatusMask);
-
-/* Function Name:
- *      rtk_int_status_get
- * Description:
- *      Get interrupt trigger status.
- * Input:
- *      None
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS    (value[0] (Bit0))
- *      - INT_TYPE_METER_EXCEED   (value[0] (Bit1))
- *      - INT_TYPE_LEARN_LIMIT    (value[0] (Bit2))
- *      - INT_TYPE_LINK_SPEED     (value[0] (Bit3))
- *      - INT_TYPE_CONGEST        (value[0] (Bit4))
- *      - INT_TYPE_GREEN_FEATURE  (value[0] (Bit5))
- *      - INT_TYPE_LOOP_DETECT    (value[0] (Bit6))
- *      - INT_TYPE_8051           (value[0] (Bit7))
- *      - INT_TYPE_CABLE_DIAG     (value[0] (Bit8))
- *      - INT_TYPE_ACL            (value[0] (Bit9))
- *      - INT_TYPE_SLIENT         (value[0] (Bit11))
- *
- */
-extern rtk_api_ret_t rtk_int_status_get(rtk_int_status_t* pStatusMask);
-
-/* Function Name:
- *      rtk_int_advanceInfo_get
- * Description:
- *      Get interrupt advanced information.
- * Input:
- *      adv_type - Advanced interrupt type.
- * Output:
- *      info - Information per type.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get advanced information when interrupt happened.
- *      The status will be cleared after execute this API.
- */
-extern rtk_api_ret_t rtk_int_advanceInfo_get(rtk_int_advType_t adv_type, rtk_int_info_t* info);
-
-
-#endif /* __RTK_API_INTERRUPT_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/l2.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/l2.h
deleted file mode 100644
index e0ccdbe3d7..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/l2.h
+++ /dev/null
@@ -1,1181 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes L2 module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_L2_H__
-#define __RTK_API_L2_H__
-
-
-/*
- * Data Type Declaration
- */
-#define RTK_MAX_NUM_OF_LEARN_LIMIT                  (rtk_switch_maxLutAddrNumber_get())
-
-#define RTK_MAC_ADDR_LEN                            6
-#define RTK_MAX_LUT_ADDRESS                         (RTK_MAX_NUM_OF_LEARN_LIMIT)
-#define RTK_MAX_LUT_ADDR_ID                         (RTK_MAX_LUT_ADDRESS - 1)
-
-typedef rtk_uint32 rtk_l2_age_time_t;
-
-typedef enum rtk_l2_flood_type_e
-{
-    FLOOD_UNKNOWNDA = 0,
-    FLOOD_UNKNOWNMC,
-    FLOOD_BC,
-    FLOOD_END
-} rtk_l2_flood_type_t;
-
-typedef rtk_uint32 rtk_l2_flushItem_t;
-
-typedef enum rtk_l2_flushType_e
-{
-    FLUSH_TYPE_BY_PORT = 0,       /* physical port       */
-    FLUSH_TYPE_BY_PORT_VID,       /* physical port + VID */
-    FLUSH_TYPE_BY_PORT_FID,       /* physical port + FID */
-    FLUSH_TYPE_END
-} rtk_l2_flushType_t;
-
-typedef struct rtk_l2_flushCfg_s
-{
-    rtk_enable_t    flushByVid;
-    rtk_vlan_t      vid;
-    rtk_enable_t    flushByFid;
-    rtk_uint32      fid;
-    rtk_enable_t    flushByPort;
-    rtk_port_t      port;
-    rtk_enable_t    flushByMac;
-    rtk_mac_t       ucastAddr;
-    rtk_enable_t    flushStaticAddr;
-    rtk_enable_t    flushAddrOnAllPorts; /* this is used when flushByVid */
-} rtk_l2_flushCfg_t;
-
-typedef enum rtk_l2_read_method_e{
-
-    READMETHOD_MAC = 0,
-    READMETHOD_ADDRESS,
-    READMETHOD_NEXT_ADDRESS,
-    READMETHOD_NEXT_L2UC,
-    READMETHOD_NEXT_L2MC,
-    READMETHOD_NEXT_L3MC,
-    READMETHOD_NEXT_L2L3MC,
-    READMETHOD_NEXT_L2UCSPA,
-    READMETHOD_END
-}rtk_l2_read_method_t;
-
-/* l2 limit learning count action */
-typedef enum rtk_l2_limitLearnCntAction_e
-{
-    LIMIT_LEARN_CNT_ACTION_DROP = 0,
-    LIMIT_LEARN_CNT_ACTION_FORWARD,
-    LIMIT_LEARN_CNT_ACTION_TO_CPU,
-    LIMIT_LEARN_CNT_ACTION_END
-} rtk_l2_limitLearnCntAction_t;
-
-typedef enum rtk_l2_ipmc_lookup_type_e
-{
-    LOOKUP_MAC = 0,
-    LOOKUP_IP,
-    LOOKUP_IP_VID,
-    LOOKUP_END
-} rtk_l2_ipmc_lookup_type_t;
-
-/* l2 address table - unicast data structure */
-typedef struct rtk_l2_ucastAddr_s
-{
-    rtk_mac_t       mac;
-    rtk_uint32      ivl;
-    rtk_uint32      cvid;
-    rtk_uint32      fid;
-    rtk_uint32      efid;
-    rtk_uint32      port;
-    rtk_uint32      sa_block;
-    rtk_uint32      da_block;
-    rtk_uint32      auth;
-    rtk_uint32      is_static;
-    rtk_uint32      priority;
-    rtk_uint32      sa_pri_en;
-    rtk_uint32      fwd_pri_en;
-    rtk_uint32      address;
-}rtk_l2_ucastAddr_t;
-
-/* l2 address table - multicast data structure */
-typedef struct rtk_l2_mcastAddr_s
-{
-    rtk_uint32      vid;
-    rtk_mac_t       mac;
-    rtk_uint32      fid;
-    rtk_portmask_t  portmask;
-    rtk_uint32      ivl;
-    rtk_uint32      priority;
-    rtk_uint32      fwd_pri_en;
-    rtk_uint32      igmp_asic;
-    rtk_uint32      igmp_index;
-    rtk_uint32      address;
-}rtk_l2_mcastAddr_t;
-
-/* l2 address table - ip multicast data structure */
-typedef struct rtk_l2_ipMcastAddr_s
-{
-    ipaddr_t        dip;
-    ipaddr_t        sip;
-    rtk_portmask_t  portmask;
-    rtk_uint32      priority;
-    rtk_uint32      fwd_pri_en;
-    rtk_uint32      igmp_asic;
-    rtk_uint32      igmp_index;
-    rtk_uint32      address;
-}rtk_l2_ipMcastAddr_t;
-
-/* l2 address table - ip VID multicast data structure */
-typedef struct rtk_l2_ipVidMcastAddr_s
-{
-    ipaddr_t        dip;
-    ipaddr_t        sip;
-    rtk_uint32      vid;
-    rtk_portmask_t  portmask;
-    rtk_uint32      address;
-}rtk_l2_ipVidMcastAddr_t;
-
-typedef struct rtk_l2_addr_table_s
-{
-    rtk_uint32  index;
-    ipaddr_t    sip;
-    ipaddr_t    dip;
-    rtk_mac_t   mac;
-    rtk_uint32  sa_block;
-    rtk_uint32  auth;
-    rtk_portmask_t  portmask;
-    rtk_uint32  age;
-    rtk_uint32  ivl;
-    rtk_uint32  cvid;
-    rtk_uint32  fid;
-    rtk_uint32  is_ipmul;
-    rtk_uint32  is_static;
-    rtk_uint32  is_ipvidmul;
-    rtk_uint32  l3_vid;
-}rtk_l2_addr_table_t;
-
-typedef enum rtk_l2_clearStatus_e
-{
-    L2_CLEAR_STATE_FINISH = 0,
-    L2_CLEAR_STATE_BUSY,
-    L2_CLEAR_STATE_END
-}rtk_l2_clearStatus_t;
-
-/* Function Name:
- *      rtk_l2_init
- * Description:
- *      Initialize l2 module of the specified device.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      Initialize l2 module before calling any l2 APIs.
- */
-extern rtk_api_ret_t rtk_l2_init(void);
-
-/* Function Name:
- *      rtk_l2_addr_add
- * Description:
- *      Add LUT unicast entry.
- * Input:
- *      pMac - 6 bytes unicast(I/G bit is 0) mac address to be written into LUT.
- *      pL2_data - Unicast entry parameter
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_MAC              - Invalid MAC address.
- *      RT_ERR_L2_FID           - Invalid FID .
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      If the unicast mac address already existed in LUT, it will udpate the status of the entry.
- *      Otherwise, it will find an empty or asic auto learned entry to write. If all the entries
- *      with the same hash value can't be replaced, ASIC will return a RT_ERR_L2_INDEXTBL_FULL error.
- */
-extern rtk_api_ret_t rtk_l2_addr_add(rtk_mac_t *pMac, rtk_l2_ucastAddr_t *pL2_data);
-
-/* Function Name:
- *      rtk_l2_addr_get
- * Description:
- *      Get LUT unicast entry.
- * Input:
- *      pMac    - 6 bytes unicast(I/G bit is 0) mac address to be written into LUT.
- * Output:
- *      pL2_data - Unicast entry parameter
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the unicast mac address existed in LUT, it will return the port and fid where
- *      the mac is learned. Otherwise, it will return a RT_ERR_L2_ENTRY_NOTFOUND error.
- */
-extern rtk_api_ret_t rtk_l2_addr_get(rtk_mac_t *pMac, rtk_l2_ucastAddr_t *pL2_data);
-
-/* Function Name:
- *      rtk_l2_addr_next_get
- * Description:
- *      Get Next LUT unicast entry.
- * Input:
- *      read_method     - The reading method.
- *      port            - The port number if the read_metohd is READMETHOD_NEXT_L2UCSPA
- *      pAddress        - The Address ID
- * Output:
- *      pL2_data - Unicast entry parameter
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next unicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all entries is LUT.
- */
-extern rtk_api_ret_t rtk_l2_addr_next_get(rtk_l2_read_method_t read_method, rtk_port_t port, rtk_uint32 *pAddress, rtk_l2_ucastAddr_t *pL2_data);
-
-/* Function Name:
- *      rtk_l2_addr_del
- * Description:
- *      Delete LUT unicast entry.
- * Input:
- *      pMac - 6 bytes unicast(I/G bit is 0) mac address to be written into LUT.
- *      fid - Filtering database
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the mac has existed in the LUT, it will be deleted. Otherwise, it will return RT_ERR_L2_ENTRY_NOTFOUND.
- */
-extern rtk_api_ret_t rtk_l2_addr_del(rtk_mac_t *pMac, rtk_l2_ucastAddr_t *pL2_data);
-
-/* Function Name:
- *      rtk_l2_mcastAddr_add
- * Description:
- *      Add LUT multicast entry.
- * Input:
- *      pMcastAddr  - L2 multicast entry structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_MAC              - Invalid MAC address.
- *      RT_ERR_L2_FID           - Invalid FID .
- *      RT_ERR_L2_VID           - Invalid VID .
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      If the multicast mac address already existed in the LUT, it will udpate the
- *      port mask of the entry. Otherwise, it will find an empty or asic auto learned
- *      entry to write. If all the entries with the same hash value can't be replaced,
- *      ASIC will return a RT_ERR_L2_INDEXTBL_FULL error.
- */
-extern rtk_api_ret_t rtk_l2_mcastAddr_add(rtk_l2_mcastAddr_t *pMcastAddr);
-
-/* Function Name:
- *      rtk_l2_mcastAddr_get
- * Description:
- *      Get LUT multicast entry.
- * Input:
- *      pMcastAddr  - L2 multicast entry structure
- * Output:
- *      pMcastAddr  - L2 multicast entry structure
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_VID               - Invalid VID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the multicast mac address existed in the LUT, it will return the port where
- *      the mac is learned. Otherwise, it will return a RT_ERR_L2_ENTRY_NOTFOUND error.
- */
-extern rtk_api_ret_t rtk_l2_mcastAddr_get(rtk_l2_mcastAddr_t *pMcastAddr);
-
-/* Function Name:
- *      rtk_l2_mcastAddr_next_get
- * Description:
- *      Get Next L2 Multicast entry.
- * Input:
- *      pAddress        - The Address ID
- * Output:
- *      pMcastAddr  - L2 multicast entry structure
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next L2 multicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all multicast entries is LUT.
- */
-extern rtk_api_ret_t rtk_l2_mcastAddr_next_get(rtk_uint32 *pAddress, rtk_l2_mcastAddr_t *pMcastAddr);
-
-/* Function Name:
- *      rtk_l2_mcastAddr_del
- * Description:
- *      Delete LUT multicast entry.
- * Input:
- *      pMcastAddr  - L2 multicast entry structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_VID               - Invalid VID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the mac has existed in the LUT, it will be deleted. Otherwise, it will return RT_ERR_L2_ENTRY_NOTFOUND.
- */
-extern rtk_api_ret_t rtk_l2_mcastAddr_del(rtk_l2_mcastAddr_t *pMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_add
- * Description:
- *      Add Lut IP multicast entry
- * Input:
- *      pIpMcastAddr    - IP Multicast entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      System supports L2 entry with IP multicast DIP/SIP to forward IP multicasting frame as user
- *      desired. If this function is enabled, then system will be looked up L2 IP multicast entry to
- *      forward IP multicast frame directly without flooding.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastAddr_add(rtk_l2_ipMcastAddr_t *pIpMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_get
- * Description:
- *      Get LUT IP multicast entry.
- * Input:
- *      pIpMcastAddr    - IP Multicast entry
- * Output:
- *      pIpMcastAddr    - IP Multicast entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      The API can get Lut table of IP multicast entry.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastAddr_get(rtk_l2_ipMcastAddr_t *pIpMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_next_get
- * Description:
- *      Get Next IP Multicast entry.
- * Input:
- *      pAddress        - The Address ID
- * Output:
- *      pIpMcastAddr    - IP Multicast entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next IP multicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all IP multicast entries is LUT.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastAddr_next_get(rtk_uint32 *pAddress, rtk_l2_ipMcastAddr_t *pIpMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_del
- * Description:
- *      Delete a ip multicast address entry from the specified device.
- * Input:
- *      pIpMcastAddr    - IP Multicast entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      The API can delete a IP multicast address entry from the specified device.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastAddr_del(rtk_l2_ipMcastAddr_t *pIpMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_add
- * Description:
- *      Add Lut IP multicast+VID entry
- * Input:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_ipVidMcastAddr_add(rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_get
- * Description:
- *      Get LUT IP multicast+VID entry.
- * Input:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Output:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_ipVidMcastAddr_get(rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_next_get
- * Description:
- *      Get Next IP Multicast+VID entry.
- * Input:
- *      pAddress        - The Address ID
- * Output:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next IP multicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all IP multicast entries is LUT.
- */
-extern rtk_api_ret_t rtk_l2_ipVidMcastAddr_next_get(rtk_uint32 *pAddress, rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_del
- * Description:
- *      Delete a ip multicast+VID address entry from the specified device.
- * Input:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_ipVidMcastAddr_del(rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr);
-
-/* Function Name:
- *      rtk_l2_ucastAddr_flush
- * Description:
- *      Flush L2 mac address by type in the specified device (both dynamic and static).
- * Input:
- *      pConfig - flush configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      flushByVid          - 1: Flush by VID, 0: Don't flush by VID
- *      vid                 - VID (0 ~ 4095)
- *      flushByFid          - 1: Flush by FID, 0: Don't flush by FID
- *      fid                 - FID (0 ~ 15)
- *      flushByPort         - 1: Flush by Port, 0: Don't flush by Port
- *      port                - Port ID
- *      flushByMac          - Not Supported
- *      ucastAddr           - Not Supported
- *      flushStaticAddr     - 1: Flush both Static and Dynamic entries, 0: Flush only Dynamic entries
- *      flushAddrOnAllPorts - 1: Flush VID-matched entries at all ports, 0: Flush VID-matched entries per port.
- */
-extern rtk_api_ret_t rtk_l2_ucastAddr_flush(rtk_l2_flushCfg_t *pConfig);
-
-/* Function Name:
- *      rtk_l2_table_clear
- * Description:
- *      Flush all static & dynamic entries in LUT.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_table_clear(void);
-
-/* Function Name:
- *      rtk_l2_table_clearStatus_get
- * Description:
- *      Get table clear status
- * Input:
- *      None
- * Output:
- *      pStatus - Clear status, 1:Busy, 0:finish
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_table_clearStatus_get(rtk_l2_clearStatus_t *pStatus);
-
-/* Function Name:
- *      rtk_l2_flushLinkDownPortAddrEnable_set
- * Description:
- *      Set HW flush linkdown port mac configuration of the specified device.
- * Input:
- *      port - Port id.
- *      enable - link down flush status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The status of flush linkdown port address is as following:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_l2_flushLinkDownPortAddrEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_l2_flushLinkDownPortAddrEnable_get
- * Description:
- *      Get HW flush linkdown port mac configuration of the specified device.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - link down flush status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The status of flush linkdown port address is as following:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_l2_flushLinkDownPortAddrEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_l2_agingEnable_set
- * Description:
- *      Set L2 LUT aging status per port setting.
- * Input:
- *      port    - Port id.
- *      enable  - Aging status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can be used to set L2 LUT aging status per port.
- */
-extern rtk_api_ret_t rtk_l2_agingEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_l2_agingEnable_get
- * Description:
- *      Get L2 LUT aging status per port setting.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Aging status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can be used to get L2 LUT aging function per port.
- */
-extern rtk_api_ret_t rtk_l2_agingEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_l2_limitLearningCnt_set
- * Description:
- *      Set per-Port auto learning limit number
- * Input:
- *      port    - Port id.
- *      mac_cnt - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_LIMITED_L2ENTRY_NUM  - Invalid auto learning limit number
- * Note:
- *      The API can set per-port ASIC auto learning limit number from 0(disable learning)
- *      to 8k.
- */
-extern rtk_api_ret_t rtk_l2_limitLearningCnt_set(rtk_port_t port, rtk_mac_cnt_t mac_cnt);
-
-/* Function Name:
- *      rtk_l2_limitLearningCnt_get
- * Description:
- *      Get per-Port auto learning limit number
- * Input:
- *      port - Port id.
- * Output:
- *      pMac_cnt - Auto learning entries limit number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get per-port ASIC auto learning limit number.
- */
-extern rtk_api_ret_t rtk_l2_limitLearningCnt_get(rtk_port_t port, rtk_mac_cnt_t *pMac_cnt);
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCnt_set
- * Description:
- *      Set System auto learning limit number
- * Input:
- *      mac_cnt - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_LIMITED_L2ENTRY_NUM  - Invalid auto learning limit number
- * Note:
- *      The API can set system ASIC auto learning limit number from 0(disable learning)
- *      to 2112.
- */
-extern rtk_api_ret_t rtk_l2_limitSystemLearningCnt_set(rtk_mac_cnt_t mac_cnt);
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCnt_get
- * Description:
- *      Get System auto learning limit number
- * Input:
- *      None
- * Output:
- *      pMac_cnt - Auto learning entries limit number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get system ASIC auto learning limit number.
- */
-extern rtk_api_ret_t rtk_l2_limitSystemLearningCnt_get(rtk_mac_cnt_t *pMac_cnt);
-
-/* Function Name:
- *      rtk_l2_limitLearningCntAction_set
- * Description:
- *      Configure auto learn over limit number action.
- * Input:
- *      port - Port id.
- *      action - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_NOT_ALLOWED  - Invalid learn over action
- * Note:
- *      The API can set SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-extern rtk_api_ret_t rtk_l2_limitLearningCntAction_set(rtk_port_t port, rtk_l2_limitLearnCntAction_t action);
-
-/* Function Name:
- *      rtk_l2_limitLearningCntAction_get
- * Description:
- *      Get auto learn over limit number action.
- * Input:
- *      port - Port id.
- * Output:
- *      pAction - Learn over action
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-extern rtk_api_ret_t rtk_l2_limitLearningCntAction_get(rtk_port_t port, rtk_l2_limitLearnCntAction_t *pAction);
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntAction_set
- * Description:
- *      Configure system auto learn over limit number action.
- * Input:
- *      port - Port id.
- *      action - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_NOT_ALLOWED  - Invalid learn over action
- * Note:
- *      The API can set SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-extern rtk_api_ret_t rtk_l2_limitSystemLearningCntAction_set(rtk_l2_limitLearnCntAction_t action);
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntAction_get
- * Description:
- *      Get system auto learn over limit number action.
- * Input:
- *      None.
- * Output:
- *      pAction - Learn over action
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-extern rtk_api_ret_t rtk_l2_limitSystemLearningCntAction_get(rtk_l2_limitLearnCntAction_t *pAction);
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntPortMask_set
- * Description:
- *      Configure system auto learn portmask
- * Input:
- *      pPortmask - Port Mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid port mask.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_limitSystemLearningCntPortMask_set(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntPortMask_get
- * Description:
- *      get system auto learn portmask
- * Input:
- *      None
- * Output:
- *      pPortmask - Port Mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Null pointer.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_limitSystemLearningCntPortMask_get(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_l2_learningCnt_get
- * Description:
- *      Get per-Port current auto learning number
- * Input:
- *      port - Port id.
- * Output:
- *      pMac_cnt - ASIC auto learning entries number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get per-port ASIC auto learning number
- */
-extern rtk_api_ret_t rtk_l2_learningCnt_get(rtk_port_t port, rtk_mac_cnt_t *pMac_cnt);
-
-/* Function Name:
- *      rtk_l2_floodPortMask_set
- * Description:
- *      Set flooding portmask
- * Input:
- *      type - flooding type.
- *      pFlood_portmask - flooding porkmask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set the flooding mask.
- *      The flooding type is as following:
- *      - FLOOD_UNKNOWNDA
- *      - FLOOD_UNKNOWNMC
- *      - FLOOD_BC
- */
-extern rtk_api_ret_t rtk_l2_floodPortMask_set(rtk_l2_flood_type_t floood_type, rtk_portmask_t *pFlood_portmask);
-
-/* Function Name:
- *      rtk_l2_floodPortMask_get
- * Description:
- *      Get flooding portmask
- * Input:
- *      type - flooding type.
- * Output:
- *      pFlood_portmask - flooding porkmask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get the flooding mask.
- *      The flooding type is as following:
- *      - FLOOD_UNKNOWNDA
- *      - FLOOD_UNKNOWNMC
- *      - FLOOD_BC
- */
-extern rtk_api_ret_t rtk_l2_floodPortMask_get(rtk_l2_flood_type_t floood_type, rtk_portmask_t *pFlood_portmask);
-
-/* Function Name:
- *      rtk_l2_localPktPermit_set
- * Description:
- *      Set permittion of frames if source port and destination port are the same.
- * Input:
- *      port - Port id.
- *      permit - permittion status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid permit value.
- * Note:
- *      This API is setted to permit frame if its source port is equal to destination port.
- */
-extern rtk_api_ret_t rtk_l2_localPktPermit_set(rtk_port_t port, rtk_enable_t permit);
-
-/* Function Name:
- *      rtk_l2_localPktPermit_get
- * Description:
- *      Get permittion of frames if source port and destination port are the same.
- * Input:
- *      port - Port id.
- * Output:
- *      pPermit - permittion status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API is to get permittion status for frames if its source port is equal to destination port.
- */
-extern rtk_api_ret_t rtk_l2_localPktPermit_get(rtk_port_t port, rtk_enable_t *pPermit);
-
-/* Function Name:
- *      rtk_l2_aging_set
- * Description:
- *      Set LUT agging out speed
- * Input:
- *      aging_time - Agging out time.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can set LUT agging out period for each entry and the range is from 14s to 800s.
- */
-extern rtk_api_ret_t rtk_l2_aging_set(rtk_l2_age_time_t aging_time);
-
-/* Function Name:
- *      rtk_l2_aging_get
- * Description:
- *      Get LUT agging out time
- * Input:
- *      None
- * Output:
- *      pEnable - Aging status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get LUT agging out period for each entry.
- */
-extern rtk_api_ret_t rtk_l2_aging_get(rtk_l2_age_time_t *pAging_time);
-
-/* Function Name:
- *      rtk_l2_ipMcastAddrLookup_set
- * Description:
- *      Set Lut IP multicast lookup function
- * Input:
- *      type - Lookup type for IPMC packet.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      This API can work with rtk_l2_ipMcastAddrLookupException_add.
- *      If users set the lookup type to DIP, the group in exception table
- *      will be lookup by DIP+SIP
- *      If users set the lookup type to DIP+SIP, the group in exception table
- *      will be lookup by only DIP
- */
-extern rtk_api_ret_t rtk_l2_ipMcastAddrLookup_set(rtk_l2_ipmc_lookup_type_t type);
-
-/* Function Name:
- *      rtk_l2_ipMcastAddrLookup_get
- * Description:
- *      Get Lut IP multicast lookup function
- * Input:
- *      None.
- * Output:
- *      pType - Lookup type for IPMC packet.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastAddrLookup_get(rtk_l2_ipmc_lookup_type_t *pType);
-
-/* Function Name:
- *      rtk_l2_ipMcastForwardRouterPort_set
- * Description:
- *      Set IPMC packet forward to rounter port also or not
- * Input:
- *      enabled - 1: Inlcude router port, 0, exclude router port
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_ipMcastForwardRouterPort_set(rtk_enable_t enabled);
-
-/* Function Name:
- *      rtk_l2_ipMcastForwardRouterPort_get
- * Description:
- *      Get IPMC packet forward to rounter port also or not
- * Input:
- *      None.
- * Output:
- *      pEnabled    - 1: Inlcude router port, 0, exclude router port
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_l2_ipMcastForwardRouterPort_get(rtk_enable_t *pEnabled);
-
-/* Function Name:
- *      rtk_l2_ipMcastGroupEntry_add
- * Description:
- *      Add an IP Multicast entry to group table
- * Input:
- *      ip_addr     - IP address
- *      vid         - VLAN ID
- *      pPortmask   - portmask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- *      RT_ERR_TBL_FULL    - Table Full
- * Note:
- *      Add an entry to IP Multicast Group table.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastGroupEntry_add(ipaddr_t ip_addr, rtk_uint32 vid, rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_l2_ipMcastGroupEntry_del
- * Description:
- *      Delete an entry from IP Multicast group table
- * Input:
- *      ip_addr     - IP address
- *      vid         - VLAN ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- *      RT_ERR_TBL_FULL    - Table Full
- * Note:
- *      Delete an entry from IP Multicast group table.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastGroupEntry_del(ipaddr_t ip_addr, rtk_uint32 vid);
-
-/* Function Name:
- *      rtk_l2_ipMcastGroupEntry_get
- * Description:
- *      get an entry from IP Multicast group table
- * Input:
- *      ip_addr     - IP address
- *      vid         - VLAN ID
- * Output:
- *      pPortmask   - member port mask
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- *      RT_ERR_TBL_FULL    - Table Full
- * Note:
- *      Delete an entry from IP Multicast group table.
- */
-extern rtk_api_ret_t rtk_l2_ipMcastGroupEntry_get(ipaddr_t ip_addr, rtk_uint32 vid, rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_l2_entry_get
- * Description:
- *      Get LUT unicast entry.
- * Input:
- *      pL2_entry - Index field in the structure.
- * Output:
- *      pL2_entry - other fields such as MAC, port, age...
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_L2_EMPTY_ENTRY   - Empty LUT entry.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      This API is used to get address by index from 0~2111.
- */
-extern rtk_api_ret_t rtk_l2_entry_get(rtk_l2_addr_table_t *pL2_entry);
-
-
-#endif /* __RTK_API_L2_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/leaky.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/leaky.h
deleted file mode 100644
index 13ef60df83..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/leaky.h
+++ /dev/null
@@ -1,371 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes Leaky module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_LEAKY_H__
-#define __RTK_API_LEAKY_H__
-
-
-typedef enum rtk_leaky_type_e
-{
-    LEAKY_BRG_GROUP = 0,
-    LEAKY_FD_PAUSE,
-    LEAKY_SP_MCAST,
-    LEAKY_1X_PAE,
-    LEAKY_UNDEF_BRG_04,
-    LEAKY_UNDEF_BRG_05,
-    LEAKY_UNDEF_BRG_06,
-    LEAKY_UNDEF_BRG_07,
-    LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
-    LEAKY_UNDEF_BRG_09,
-    LEAKY_UNDEF_BRG_0A,
-    LEAKY_UNDEF_BRG_0B,
-    LEAKY_UNDEF_BRG_0C,
-    LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
-    LEAKY_8021AB,
-    LEAKY_UNDEF_BRG_0F,
-    LEAKY_BRG_MNGEMENT,
-    LEAKY_UNDEFINED_11,
-    LEAKY_UNDEFINED_12,
-    LEAKY_UNDEFINED_13,
-    LEAKY_UNDEFINED_14,
-    LEAKY_UNDEFINED_15,
-    LEAKY_UNDEFINED_16,
-    LEAKY_UNDEFINED_17,
-    LEAKY_UNDEFINED_18,
-    LEAKY_UNDEFINED_19,
-    LEAKY_UNDEFINED_1A,
-    LEAKY_UNDEFINED_1B,
-    LEAKY_UNDEFINED_1C,
-    LEAKY_UNDEFINED_1D,
-    LEAKY_UNDEFINED_1E,
-    LEAKY_UNDEFINED_1F,
-    LEAKY_GMRP,
-    LEAKY_GVRP,
-    LEAKY_UNDEF_GARP_22,
-    LEAKY_UNDEF_GARP_23,
-    LEAKY_UNDEF_GARP_24,
-    LEAKY_UNDEF_GARP_25,
-    LEAKY_UNDEF_GARP_26,
-    LEAKY_UNDEF_GARP_27,
-    LEAKY_UNDEF_GARP_28,
-    LEAKY_UNDEF_GARP_29,
-    LEAKY_UNDEF_GARP_2A,
-    LEAKY_UNDEF_GARP_2B,
-    LEAKY_UNDEF_GARP_2C,
-    LEAKY_UNDEF_GARP_2D,
-    LEAKY_UNDEF_GARP_2E,
-    LEAKY_UNDEF_GARP_2F,
-    LEAKY_IGMP,
-    LEAKY_IPMULTICAST,
-    LEAKY_CDP,
-    LEAKY_CSSTP,
-    LEAKY_LLDP,
-    LEAKY_END,
-}rtk_leaky_type_t;
-
-/* Function Name:
- *      rtk_leaky_vlan_set
- * Description:
- *      Set VLAN leaky.
- * Input:
- *      type - Packet type for VLAN leaky.
- *      enable - Leaky status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      This API can set VLAN leaky for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-extern rtk_api_ret_t rtk_leaky_vlan_set(rtk_leaky_type_t type, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_leaky_vlan_get
- * Description:
- *      Get VLAN leaky.
- * Input:
- *      type - Packet type for VLAN leaky.
- * Output:
- *      pEnable - Leaky status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get VLAN leaky status for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP  packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-extern rtk_api_ret_t rtk_leaky_vlan_get(rtk_leaky_type_t type, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_leaky_portIsolation_set
- * Description:
- *      Set port isolation leaky.
- * Input:
- *      type - Packet type for port isolation leaky.
- *      enable - Leaky status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      This API can set port isolation leaky for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP  packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-extern rtk_api_ret_t rtk_leaky_portIsolation_set(rtk_leaky_type_t type, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_leaky_portIsolation_get
- * Description:
- *      Get port isolation leaky.
- * Input:
- *      type - Packet type for port isolation leaky.
- * Output:
- *      pEnable - Leaky status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get port isolation leaky status for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP  packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-extern rtk_api_ret_t rtk_leaky_portIsolation_get(rtk_leaky_type_t type, rtk_enable_t *pEnable);
-
-#endif /* __RTK_API_LEAKY_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h
deleted file mode 100644
index 71acc7c92c..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h
+++ /dev/null
@@ -1,481 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes LED module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_LED_H__
-#define __RTK_API_LED_H__
-
-typedef enum rtk_led_operation_e
-{
-    LED_OP_SCAN=0,
-    LED_OP_PARALLEL,
-    LED_OP_SERIAL,
-    LED_OP_END,
-}rtk_led_operation_t;
-
-
-typedef enum rtk_led_active_e
-{
-    LED_ACTIVE_HIGH=0,
-    LED_ACTIVE_LOW,
-    LED_ACTIVE_END,
-}rtk_led_active_t;
-
-typedef enum rtk_led_config_e
-{
-    LED_CONFIG_LEDOFF=0,
-    LED_CONFIG_DUPCOL,
-    LED_CONFIG_LINK_ACT,
-    LED_CONFIG_SPD1000,
-    LED_CONFIG_SPD100,
-    LED_CONFIG_SPD10,
-    LED_CONFIG_SPD1000ACT,
-    LED_CONFIG_SPD100ACT,
-    LED_CONFIG_SPD10ACT,
-    LED_CONFIG_SPD10010ACT,
-    LED_CONFIG_LOOPDETECT,
-    LED_CONFIG_EEE,
-    LED_CONFIG_LINKRX,
-    LED_CONFIG_LINKTX,
-    LED_CONFIG_MASTER,
-    LED_CONFIG_ACT,
-    LED_CONFIG_END,
-}rtk_led_congig_t;
-
-typedef struct rtk_led_ability_s
-{
-    rtk_enable_t link_10m;
-    rtk_enable_t link_100m;
-    rtk_enable_t link_500m;
-    rtk_enable_t link_1000m;
-    rtk_enable_t act_rx;
-    rtk_enable_t act_tx;
-}rtk_led_ability_t;
-
-typedef enum rtk_led_blink_rate_e
-{
-    LED_BLINKRATE_32MS=0,
-    LED_BLINKRATE_64MS,
-    LED_BLINKRATE_128MS,
-    LED_BLINKRATE_256MS,
-    LED_BLINKRATE_512MS,
-    LED_BLINKRATE_1024MS,
-    LED_BLINKRATE_48MS,
-    LED_BLINKRATE_96MS,
-    LED_BLINKRATE_END,
-}rtk_led_blink_rate_t;
-
-typedef enum rtk_led_group_e
-{
-    LED_GROUP_0 = 0,
-    LED_GROUP_1,
-    LED_GROUP_2,
-    LED_GROUP_END
-}rtk_led_group_t;
-
-
-typedef enum rtk_led_force_mode_e
-{
-    LED_FORCE_NORMAL=0,
-    LED_FORCE_BLINK,
-    LED_FORCE_OFF,
-    LED_FORCE_ON,
-    LED_FORCE_END
-}rtk_led_force_mode_t;
-
-typedef enum rtk_led_serialOutput_e
-{
-    SERIAL_LED_NONE = 0,
-    SERIAL_LED_0,
-    SERIAL_LED_0_1,
-    SERIAL_LED_0_2,
-    SERIAL_LED_END,
-}rtk_led_serialOutput_t;
-
-
-/* Function Name:
- *      rtk_led_enable_set
- * Description:
- *      Set Led enable congiuration
- * Input:
- *      group       - LED group id.
- *      pPortmask    - LED enable port mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can be used to enable LED per port per group.
- */
-extern rtk_api_ret_t rtk_led_enable_set(rtk_led_group_t group, rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_led_enable_get
- * Description:
- *      Get Led enable congiuration
- * Input:
- *      group - LED group id.
- * Output:
- *      pPortmask - LED enable port mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can be used to get LED enable status.
- */
-extern rtk_api_ret_t rtk_led_enable_get(rtk_led_group_t group, rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_led_operation_set
- * Description:
- *      Set Led operation mode
- * Input:
- *      mode - LED operation mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set Led operation mode.
- *      The modes that can be set are as following:
- *      - LED_OP_SCAN,
- *      - LED_OP_PARALLEL,
- *      - LED_OP_SERIAL,
- */
-extern rtk_api_ret_t rtk_led_operation_set(rtk_led_operation_t mode);
-
-/* Function Name:
- *      rtk_led_operation_get
- * Description:
- *      Get Led operation mode
- * Input:
- *      None
- * Output:
- *      pMode - Support LED operation mode.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get Led operation mode.
- *      The modes that can be set are as following:
- *      - LED_OP_SCAN,
- *      - LED_OP_PARALLEL,
- *      - LED_OP_SERIAL,
- */
-extern rtk_api_ret_t rtk_led_operation_get(rtk_led_operation_t *pMode);
-
-/* Function Name:
- *      rtk_led_modeForce_set
- * Description:
- *      Set Led group to congiuration force mode
- * Input:
- *      port    - port ID
- *      group   - Support LED group id.
- *      mode    - Support LED force mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Error Port ID
- * Note:
- *      The API can force to one force mode.
- *      The force modes that can be set are as following:
- *      - LED_FORCE_NORMAL,
- *      - LED_FORCE_BLINK,
- *      - LED_FORCE_OFF,
- *      - LED_FORCE_ON.
- */
-extern rtk_api_ret_t rtk_led_modeForce_set(rtk_port_t port, rtk_led_group_t group, rtk_led_force_mode_t mode);
-
-/* Function Name:
- *      rtk_led_modeForce_get
- * Description:
- *      Get Led group to congiuration force mode
- * Input:
- *      port  - port ID
- *      group - Support LED group id.
- *      pMode - Support LED force mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Error Port ID
- * Note:
- *      The API can get forced Led group mode.
- *      The force modes that can be set are as following:
- *      - LED_FORCE_NORMAL,
- *      - LED_FORCE_BLINK,
- *      - LED_FORCE_OFF,
- *      - LED_FORCE_ON.
- */
-extern rtk_api_ret_t rtk_led_modeForce_get(rtk_port_t port, rtk_led_group_t group, rtk_led_force_mode_t *pMode);
-
-/* Function Name:
- *      rtk_led_blinkRate_set
- * Description:
- *      Set LED blinking rate
- * Input:
- *      blinkRate - blinking rate.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      ASIC support 6 types of LED blinking rates at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms.
- */
-extern rtk_api_ret_t rtk_led_blinkRate_set(rtk_led_blink_rate_t blinkRate);
-
-/* Function Name:
- *      rtk_led_blinkRate_get
- * Description:
- *      Get LED blinking rate at mode 0 to mode 3
- * Input:
- *      None
- * Output:
- *      pBlinkRate - blinking rate.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      There are  6 types of LED blinking rates at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms.
- */
-extern rtk_api_ret_t rtk_led_blinkRate_get(rtk_led_blink_rate_t *pBlinkRate);
-
-/* Function Name:
- *      rtk_led_groupConfig_set
- * Description:
- *      Set per group Led to congiuration mode
- * Input:
- *      group   - LED group.
- *      config  - LED configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set LED indicated information configuration for each LED group with 1 to 1 led mapping to each port.
- *      - Definition  LED Statuses      Description
- *      - 0000        LED_Off           LED pin Tri-State.
- *      - 0001        Dup/Col           Collision, Full duplex Indicator.
- *      - 0010        Link/Act          Link, Activity Indicator.
- *      - 0011        Spd1000           1000Mb/s Speed Indicator.
- *      - 0100        Spd100            100Mb/s Speed Indicator.
- *      - 0101        Spd10             10Mb/s Speed Indicator.
- *      - 0110        Spd1000/Act       1000Mb/s Speed/Activity Indicator.
- *      - 0111        Spd100/Act        100Mb/s Speed/Activity Indicator.
- *      - 1000        Spd10/Act         10Mb/s Speed/Activity Indicator.
- *      - 1001        Spd100 (10)/Act   10/100Mb/s Speed/Activity Indicator.
- *      - 1010        LoopDetect        LoopDetect Indicator.
- *      - 1011        EEE               EEE Indicator.
- *      - 1100        Link/Rx           Link, Activity Indicator.
- *      - 1101        Link/Tx           Link, Activity Indicator.
- *      - 1110        Master            Link on Master Indicator.
- *      - 1111        Act               Activity Indicator. Low for link established.
- */
-extern rtk_api_ret_t rtk_led_groupConfig_set(rtk_led_group_t group, rtk_led_congig_t config);
-
-/* Function Name:
- *      rtk_led_groupConfig_get
- * Description:
- *      Get Led group congiuration mode
- * Input:
- *      group - LED group.
- * Output:
- *      pConfig - LED configuration.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *       The API can get LED indicated information configuration for each LED group.
- */
-extern rtk_api_ret_t rtk_led_groupConfig_get(rtk_led_group_t group, rtk_led_congig_t *pConfig);
-
-/* Function Name:
- *      rtk_led_groupAbility_set
- * Description:
- *      Configure per group Led ability
- * Input:
- *      group    - LED group.
- *      pAbility - LED ability
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      None.
- */
-
-extern rtk_api_ret_t rtk_led_groupAbility_set(rtk_led_group_t group, rtk_led_ability_t *pAbility);
-
-/* Function Name:
- *      rtk_led_groupAbility_get
- * Description:
- *      Get per group Led ability
- * Input:
- *      group    - LED group.
- *      pAbility - LED ability
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      None.
- */
-
-extern rtk_api_ret_t rtk_led_groupAbility_get(rtk_led_group_t group, rtk_led_ability_t *pAbility);
-
-/* Function Name:
- *      rtk_led_serialMode_set
- * Description:
- *      Set Led serial mode active congiuration
- * Input:
- *      active - LED group.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set LED serial mode active congiuration.
- */
-extern rtk_api_ret_t rtk_led_serialMode_set(rtk_led_active_t active);
-
-/* Function Name:
- *      rtk_led_serialMode_get
- * Description:
- *      Get Led group congiuration mode
- * Input:
- *      group - LED group.
- * Output:
- *      pConfig - LED configuration.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *       The API can get LED serial mode active configuration.
- */
-extern rtk_api_ret_t rtk_led_serialMode_get(rtk_led_active_t *pActive);
-
-/* Function Name:
- *      rtk_led_OutputEnable_set
- * Description:
- *      This API set LED I/O state.
- * Input:
- *      enabled     - LED I/O state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set LED I/O state.
- */
-extern rtk_api_ret_t rtk_led_OutputEnable_set(rtk_enable_t state);
-
-
-/* Function Name:
- *      rtk_led_OutputEnable_get
- * Description:
- *      This API get LED I/O state.
- * Input:
- *      None.
- * Output:
- *      pEnabled        - LED I/O state
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set current LED I/O  state.
- */
-extern rtk_api_ret_t rtk_led_OutputEnable_get(rtk_enable_t *pState);
-
-/* Function Name:
- *      rtk_led_serialModePortmask_set
- * Description:
- *      This API configure Serial LED output Group and portmask
- * Input:
- *      output          - output group
- *      pPortmask       - output portmask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_led_serialModePortmask_set(rtk_led_serialOutput_t output, rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_led_serialModePortmask_get
- * Description:
- *      This API get Serial LED output Group and portmask
- * Input:
- *      None.
- * Output:
- *      pOutput         - output group
- *      pPortmask       - output portmask
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_led_serialModePortmask_get(rtk_led_serialOutput_t *pOutput, rtk_portmask_t *pPortmask);
-
-#endif /* __RTK_API_LED_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/mirror.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/mirror.h
deleted file mode 100644
index 1e984b7d80..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/mirror.h
+++ /dev/null
@@ -1,272 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes Mirror module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_MIRROR_H__
-#define __RTK_API_MIRROR_H__
-
-typedef enum rtk_mirror_keep_e
-{
-    MIRROR_FOLLOW_VLAN = 0,
-    MIRROR_KEEP_ORIGINAL,
-    MIRROR_KEEP_END
-}rtk_mirror_keep_t;
-
-
-/* Function Name:
- *      rtk_mirror_portBased_set
- * Description:
- *      Set port mirror function.
- * Input:
- *      mirroring_port          - Monitor port.
- *      pMirrored_rx_portmask   - Rx mirror port mask.
- *      pMirrored_tx_portmask   - Tx mirror port mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      The API is to set mirror function of source port and mirror port.
- *      The mirror port can only be set to one port and the TX and RX mirror ports
- *      should be identical.
- */
-extern rtk_api_ret_t rtk_mirror_portBased_set(rtk_port_t mirroring_port, rtk_portmask_t *pMirrored_rx_portmask, rtk_portmask_t *pMirrored_tx_portmask);
-
-/* Function Name:
- *      rtk_mirror_portBased_get
- * Description:
- *      Get port mirror function.
- * Input:
- *      None
- * Output:
- *      pMirroring_port         - Monitor port.
- *      pMirrored_rx_portmask   - Rx mirror port mask.
- *      pMirrored_tx_portmask   - Tx mirror port mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror function of source port and mirror port.
- */
-extern rtk_api_ret_t rtk_mirror_portBased_get(rtk_port_t* pMirroring_port, rtk_portmask_t *pMirrored_rx_portmask, rtk_portmask_t *pMirrored_tx_portmask);
-
-/* Function Name:
- *      rtk_mirror_portIso_set
- * Description:
- *      Set mirror port isolation.
- * Input:
- *      enable |Mirror isolation status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set mirror isolation function that prevent normal forwarding packets to miror port.
- */
-extern rtk_api_ret_t rtk_mirror_portIso_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_mirror_portIso_get
- * Description:
- *      Get mirror port isolation.
- * Input:
- *      None
- * Output:
- *      pEnable |Mirror isolation status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror isolation status.
- */
-extern rtk_api_ret_t rtk_mirror_portIso_get(rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_mirror_vlanLeaky_set
- * Description:
- *      Set mirror VLAN leaky.
- * Input:
- *      txenable -TX leaky enable.
- *      rxenable - RX leaky enable.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set mirror VLAN leaky function forwarding packets to miror port.
- */
-extern rtk_api_ret_t rtk_mirror_vlanLeaky_set(rtk_enable_t txenable, rtk_enable_t rxenable);
-
-
-/* Function Name:
- *      rtk_mirror_vlanLeaky_get
- * Description:
- *      Get mirror VLAN leaky.
- * Input:
- *      None
- * Output:
- *      pTxenable - TX leaky enable.
- *      pRxenable - RX leaky enable.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror VLAN leaky status.
- */
-extern rtk_api_ret_t rtk_mirror_vlanLeaky_get(rtk_enable_t *pTxenable, rtk_enable_t *pRxenable);
-
-/* Function Name:
- *      rtk_mirror_isolationLeaky_set
- * Description:
- *      Set mirror Isolation leaky.
- * Input:
- *      txenable -TX leaky enable.
- *      rxenable - RX leaky enable.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set mirror VLAN leaky function forwarding packets to miror port.
- */
-extern rtk_api_ret_t rtk_mirror_isolationLeaky_set(rtk_enable_t txenable, rtk_enable_t rxenable);
-
-/* Function Name:
- *      rtk_mirror_isolationLeaky_get
- * Description:
- *      Get mirror isolation leaky.
- * Input:
- *      None
- * Output:
- *      pTxenable - TX leaky enable.
- *      pRxenable - RX leaky enable.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror isolation leaky status.
- */
-extern rtk_api_ret_t rtk_mirror_isolationLeaky_get(rtk_enable_t *pTxenable, rtk_enable_t *pRxenable);
-
-/* Function Name:
- *      rtk_mirror_keep_set
- * Description:
- *      Set mirror packet format keep.
- * Input:
- *      mode - -mirror keep mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set  -mirror keep mode.
- *      The mirror keep mode is as following:
- *      - MIRROR_FOLLOW_VLAN
- *      - MIRROR_KEEP_ORIGINAL
- *      - MIRROR_KEEP_END
- */
-extern rtk_api_ret_t rtk_mirror_keep_set(rtk_mirror_keep_t mode);
-
-
-/* Function Name:
- *      rtk_mirror_keep_get
- * Description:
- *      Get mirror packet format keep.
- * Input:
- *      None
- * Output:
- *      pMode -mirror keep mode.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror keep mode.
-  *      The mirror keep mode is as following:
- *      - MIRROR_FOLLOW_VLAN
- *      - MIRROR_KEEP_ORIGINAL
- *      - MIRROR_KEEP_END
- */
-extern rtk_api_ret_t rtk_mirror_keep_get(rtk_mirror_keep_t *pMode);
-
-/* Function Name:
- *      rtk_mirror_override_set
- * Description:
- *      Set port mirror override function.
- * Input:
- *      rxMirror        - 1: output mirrored packet, 0: output normal forward packet
- *      txMirror        - 1: output mirrored packet, 0: output normal forward packet
- *      aclMirror       - 1: output mirrored packet, 0: output normal forward packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API is to set mirror override function.
- *      This function control the output format when a port output
- *      normal forward & mirrored packet at the same time.
- */
-extern rtk_api_ret_t rtk_mirror_override_set(rtk_enable_t rxMirror, rtk_enable_t txMirror, rtk_enable_t aclMirror);
-
-/* Function Name:
- *      rtk_mirror_override_get
- * Description:
- *      Get port mirror override function.
- * Input:
- *      None
- * Output:
- *      pRxMirror       - 1: output mirrored packet, 0: output normal forward packet
- *      pTxMirror       - 1: output mirrored packet, 0: output normal forward packet
- *      pAclMirror      - 1: output mirrored packet, 0: output normal forward packet
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Null Pointer
- * Note:
- *      The API is to Get mirror override function.
- *      This function control the output format when a port output
- *      normal forward & mirrored packet at the same time.
- */
-extern rtk_api_ret_t rtk_mirror_override_get(rtk_enable_t *pRxMirror, rtk_enable_t *pTxMirror, rtk_enable_t *pAclMirror);
-
-#endif /* __RTK_API_MIRROR_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/oam.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/oam.h
deleted file mode 100644
index 1fc14bd62f..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/oam.h
+++ /dev/null
@@ -1,188 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes the following modules and sub-modules
- *           (1) OAM (802.3ah) configuration
- *
- */
-
-#ifndef __RTK_OAM_H__
-#define __RTK_OAM_H__
-
-/*
- * Symbol Definition
- */
-
-
-/*
- * Data Declaration
- */
-
-
-/*
- * Macro Declaration
- */
-
-typedef enum rtk_oam_parser_act_e
-{
-    OAM_PARSER_ACTION_FORWARD = 0,
-    OAM_PARSER_ACTION_LOOPBACK,
-    OAM_PARSER_ACTION_DISCARD,
-    OAM_PARSER_ACTION_END,
-
-} rtk_oam_parser_act_t;
-
-typedef enum rtk_oam_multiplexer_act_e
-{
-    OAM_MULTIPLEXER_ACTION_FORWARD = 0,
-    OAM_MULTIPLEXER_ACTION_DISCARD,
-    OAM_MULTIPLEXER_ACTION_CPUONLY,
-    OAM_MULTIPLEXER_ACTION_END,
-
-} rtk_oam_multiplexer_act_t;
-
-
-/*
- * Function Declaration
- */
-
-/* Function Name:
- *      rtk_oam_init
- * Description:
- *      Initialize oam module.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- * Note:
- *      Must initialize oam module before calling any oam APIs.
- */
-extern rtk_api_ret_t rtk_oam_init(void);
-
-/* Function Name:
- *      rtk_oam_state_set
- * Description:
- *      This API set OAM state.
- * Input:
- *      enabled     -OAMstate
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set OAM state.
- */
-extern rtk_api_ret_t rtk_oam_state_set(rtk_enable_t enabled);
-
-/* Function Name:
- *      rtk_oam_state_get
- * Description:
- *      This API get OAM state.
- * Input:
- *      None.
- * Output:
- *      pEnabled        - H/W IGMP state
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set current OAM state.
- */
-extern rtk_api_ret_t rtk_oam_state_get(rtk_enable_t *pEnabled);
-
-
-/* Module Name : OAM */
-
-/* Function Name:
- *      rtk_oam_parserAction_set
- * Description:
- *      Set OAM parser action
- * Input:
- *      port    - port id
- *      action  - parser action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_oam_parserAction_set(rtk_port_t port, rtk_oam_parser_act_t action);
-
-/* Function Name:
- *      rtk_oam_parserAction_set
- * Description:
- *      Get OAM parser action
- * Input:
- *      port    - port id
- * Output:
- *      pAction  - parser action
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_oam_parserAction_get(rtk_port_t port, rtk_oam_parser_act_t *pAction);
-
-
-/* Function Name:
- *      rtk_oam_multiplexerAction_set
- * Description:
- *      Set OAM multiplexer action
- * Input:
- *      port    - port id
- *      action  - parser action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_oam_multiplexerAction_set(rtk_port_t port, rtk_oam_multiplexer_act_t action);
-
-/* Function Name:
- *      rtk_oam_multiplexerAction_set
- * Description:
- *      Get OAM multiplexer action
- * Input:
- *      port    - port id
- * Output:
- *      pAction  - parser action
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_oam_multiplexerAction_get(rtk_port_t port, rtk_oam_multiplexer_act_t *pAction);
-
-
-#endif /* __RTK_OAM_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/port.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/port.h
deleted file mode 100644
index fcac1bcb84..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/port.h
+++ /dev/null
@@ -1,959 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes port module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_PORT_H__
-#define __RTK_API_PORT_H__
-
-/*
- * Data Type Declaration
- */
-
-#define PHY_CONTROL_REG                             0
-#define PHY_STATUS_REG                              1
-#define PHY_AN_ADVERTISEMENT_REG                    4
-#define PHY_AN_LINKPARTNER_REG                      5
-#define PHY_1000_BASET_CONTROL_REG                  9
-#define PHY_1000_BASET_STATUS_REG                   10
-#define PHY_RESOLVED_REG                            26
-
-#define RTK_EFID_MAX                                0x7
-
-#define RTK_FIBER_FORCE_1000M                       3
-#define RTK_FIBER_FORCE_100M                        5
-#define RTK_FIBER_FORCE_100M1000M                   7
-
-#define RTK_INDRECT_ACCESS_CRTL                     0x1f00
-#define RTK_INDRECT_ACCESS_STATUS                   0x1f01
-#define RTK_INDRECT_ACCESS_ADDRESS                  0x1f02
-#define RTK_INDRECT_ACCESS_WRITE_DATA               0x1f03
-#define RTK_INDRECT_ACCESS_READ_DATA                0x1f04
-#define RTK_INDRECT_ACCESS_DELAY                    0x1f80
-#define RTK_INDRECT_ACCESS_BURST                    0x1f81
-#define RTK_RW_MASK                                 0x2
-#define RTK_CMD_MASK                                0x1
-#define RTK_PHY_BUSY_OFFSET                         2
-
-
-typedef enum rtk_mode_ext_e
-{
-    MODE_EXT_DISABLE = 0,
-    MODE_EXT_RGMII,
-    MODE_EXT_MII_MAC,
-    MODE_EXT_MII_PHY,
-    MODE_EXT_TMII_MAC,
-    MODE_EXT_TMII_PHY,
-    MODE_EXT_GMII,
-    MODE_EXT_RMII_MAC,
-    MODE_EXT_RMII_PHY,
-    MODE_EXT_SGMII,
-    MODE_EXT_HSGMII,
-    MODE_EXT_1000X_100FX,
-    MODE_EXT_1000X,
-    MODE_EXT_100FX,
-    MODE_EXT_RGMII_2,
-    MODE_EXT_MII_MAC_2,
-    MODE_EXT_MII_PHY_2,
-    MODE_EXT_TMII_MAC_2,
-    MODE_EXT_TMII_PHY_2,
-    MODE_EXT_RMII_MAC_2,
-    MODE_EXT_RMII_PHY_2,
-    MODE_EXT_END
-} rtk_mode_ext_t;
-
-typedef enum rtk_port_duplex_e
-{
-    PORT_HALF_DUPLEX = 0,
-    PORT_FULL_DUPLEX,
-    PORT_DUPLEX_END
-} rtk_port_duplex_t;
-
-typedef enum rtk_port_linkStatus_e
-{
-    PORT_LINKDOWN = 0,
-    PORT_LINKUP,
-    PORT_LINKSTATUS_END
-} rtk_port_linkStatus_t;
-
-typedef struct  rtk_port_mac_ability_s
-{
-    rtk_uint32 forcemode;
-    rtk_uint32 speed;
-    rtk_uint32 duplex;
-    rtk_uint32 link;
-    rtk_uint32 nway;
-    rtk_uint32 txpause;
-    rtk_uint32 rxpause;
-}rtk_port_mac_ability_t;
-
-typedef struct rtk_port_phy_ability_s
-{
-    rtk_uint32    AutoNegotiation;  /*PHY register 0.12 setting for auto-negotiation process*/
-    rtk_uint32    Half_10;          /*PHY register 4.5 setting for 10BASE-TX half duplex capable*/
-    rtk_uint32    Full_10;          /*PHY register 4.6 setting for 10BASE-TX full duplex capable*/
-    rtk_uint32    Half_100;         /*PHY register 4.7 setting for 100BASE-TX half duplex capable*/
-    rtk_uint32    Full_100;         /*PHY register 4.8 setting for 100BASE-TX full duplex capable*/
-    rtk_uint32    Full_1000;        /*PHY register 9.9 setting for 1000BASE-T full duplex capable*/
-    rtk_uint32    FC;               /*PHY register 4.10 setting for flow control capability*/
-    rtk_uint32    AsyFC;            /*PHY register 4.11 setting for  asymmetric flow control capability*/
-} rtk_port_phy_ability_t;
-
-typedef rtk_uint32  rtk_port_phy_data_t;     /* phy page  */
-
-typedef enum rtk_port_phy_mdix_mode_e
-{
-    PHY_AUTO_CROSSOVER_MODE= 0,
-    PHY_FORCE_MDI_MODE,
-    PHY_FORCE_MDIX_MODE,
-    PHY_FORCE_MODE_END
-} rtk_port_phy_mdix_mode_t;
-
-typedef enum rtk_port_phy_mdix_status_e
-{
-    PHY_STATUS_AUTO_MDI_MODE= 0,
-    PHY_STATUS_AUTO_MDIX_MODE,
-    PHY_STATUS_FORCE_MDI_MODE,
-    PHY_STATUS_FORCE_MDIX_MODE,
-    PHY_STATUS_FORCE_MODE_END
-} rtk_port_phy_mdix_status_t;
-
-typedef rtk_uint32  rtk_port_phy_page_t;     /* phy page  */
-
-typedef enum rtk_port_phy_reg_e
-{
-    PHY_REG_CONTROL             = 0,
-    PHY_REG_STATUS,
-    PHY_REG_IDENTIFIER_1,
-    PHY_REG_IDENTIFIER_2,
-    PHY_REG_AN_ADVERTISEMENT,
-    PHY_REG_AN_LINKPARTNER,
-    PHY_REG_1000_BASET_CONTROL  = 9,
-    PHY_REG_1000_BASET_STATUS,
-    PHY_REG_END                 = 32
-} rtk_port_phy_reg_t;
-
-typedef enum rtk_port_phy_test_mode_e
-{
-    PHY_TEST_MODE_NORMAL= 0,
-    PHY_TEST_MODE_1,
-    PHY_TEST_MODE_2,
-    PHY_TEST_MODE_3,
-    PHY_TEST_MODE_4,
-    PHY_TEST_MODE_END
-} rtk_port_phy_test_mode_t;
-
-typedef enum rtk_port_speed_e
-{
-    PORT_SPEED_10M = 0,
-    PORT_SPEED_100M,
-    PORT_SPEED_1000M,
-    PORT_SPEED_500M,
-    PORT_SPEED_2500M,
-    PORT_SPEED_END
-} rtk_port_speed_t;
-
-typedef enum rtk_port_media_e
-{
-    PORT_MEDIA_COPPER = 0,
-    PORT_MEDIA_FIBER,
-    PORT_MEDIA_END
-}rtk_port_media_t;
-
-typedef struct rtk_rtctResult_s
-{
-    rtk_port_speed_t    linkType;
-    union
-    {
-        struct fe_result_s
-        {
-            rtk_uint32      isRxShort;
-            rtk_uint32      isTxShort;
-            rtk_uint32      isRxOpen;
-            rtk_uint32      isTxOpen;
-            rtk_uint32      isRxMismatch;
-            rtk_uint32      isTxMismatch;
-            rtk_uint32      isRxLinedriver;
-            rtk_uint32      isTxLinedriver;
-            rtk_uint32      rxLen;
-            rtk_uint32      txLen;
-        } fe_result;
-
-        struct ge_result_s
-        {
-            rtk_uint32      channelAShort;
-            rtk_uint32      channelBShort;
-            rtk_uint32      channelCShort;
-            rtk_uint32      channelDShort;
-
-            rtk_uint32      channelAOpen;
-            rtk_uint32      channelBOpen;
-            rtk_uint32      channelCOpen;
-            rtk_uint32      channelDOpen;
-
-            rtk_uint32      channelAMismatch;
-            rtk_uint32      channelBMismatch;
-            rtk_uint32      channelCMismatch;
-            rtk_uint32      channelDMismatch;
-
-            rtk_uint32      channelALinedriver;
-            rtk_uint32      channelBLinedriver;
-            rtk_uint32      channelCLinedriver;
-            rtk_uint32      channelDLinedriver;
-
-            rtk_uint32      channelALen;
-            rtk_uint32      channelBLen;
-            rtk_uint32      channelCLen;
-            rtk_uint32      channelDLen;
-        } ge_result;
-    }result;
-} rtk_rtctResult_t;
-
-/* Function Name:
- *      rtk_port_phyAutoNegoAbility_set
- * Description:
- *      Set ethernet PHY auto-negotiation desired ability.
- * Input:
- *      port        - port id.
- *      pAbility    - Ability structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      If Full_1000 bit is set to 1, the AutoNegotiation will be automatic set to 1. While both AutoNegotiation and Full_1000 are set to 0, the PHY speed and duplex selection will
- *      be set as following 100F > 100H > 10F > 10H priority sequence.
- */
-extern rtk_api_ret_t rtk_port_phyAutoNegoAbility_set(rtk_port_t port, rtk_port_phy_ability_t *pAbility);
-
-/* Function Name:
- *      rtk_port_phyAutoNegoAbility_get
- * Description:
- *      Get PHY ability through PHY registers.
- * Input:
- *      port - Port id.
- * Output:
- *      pAbility - Ability structure
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      Get the capablity of specified PHY.
- */
-extern rtk_api_ret_t rtk_port_phyAutoNegoAbility_get(rtk_port_t port, rtk_port_phy_ability_t *pAbility);
-
-/* Function Name:
- *      rtk_port_phyForceModeAbility_set
- * Description:
- *      Set the port speed/duplex mode/pause/asy_pause in the PHY force mode.
- * Input:
- *      port        - port id.
- *      pAbility    - Ability structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      While both AutoNegotiation and Full_1000 are set to 0, the PHY speed and duplex selection will
- *      be set as following 100F > 100H > 10F > 10H priority sequence.
- */
-extern rtk_api_ret_t rtk_port_phyForceModeAbility_set(rtk_port_t port, rtk_port_phy_ability_t *pAbility);
-
-/* Function Name:
- *      rtk_port_phyForceModeAbility_get
- * Description:
- *      Get PHY ability through PHY registers.
- * Input:
- *      port - Port id.
- * Output:
- *      pAbility - Ability structure
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      Get the capablity of specified PHY.
- */
-extern rtk_api_ret_t rtk_port_phyForceModeAbility_get(rtk_port_t port, rtk_port_phy_ability_t *pAbility);
-
-/* Function Name:
- *      rtk_port_phyStatus_get
- * Description:
- *      Get ethernet PHY linking status
- * Input:
- *      port - Port id.
- * Output:
- *      linkStatus  - PHY link status
- *      speed       - PHY link speed
- *      duplex      - PHY duplex mode
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      API will return auto negotiation status of phy.
- */
-extern rtk_api_ret_t rtk_port_phyStatus_get(rtk_port_t port, rtk_port_linkStatus_t *pLinkStatus, rtk_port_speed_t *pSpeed, rtk_port_duplex_t *pDuplex);
-
-/* Function Name:
- *      rtk_port_macForceLink_set
- * Description:
- *      Set port force linking configuration.
- * Input:
- *      port            - port id.
- *      pPortability    - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can set Port/MAC force mode properties.
- */
-extern rtk_api_ret_t rtk_port_macForceLink_set(rtk_port_t port, rtk_port_mac_ability_t *pPortability);
-
-/* Function Name:
- *      rtk_port_macForceLink_get
- * Description:
- *      Get port force linking configuration.
- * Input:
- *      port - Port id.
- * Output:
- *      pPortability - port ability configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get Port/MAC force mode properties.
- */
-extern rtk_api_ret_t rtk_port_macForceLink_get(rtk_port_t port, rtk_port_mac_ability_t *pPortability);
-
-/* Function Name:
- *      rtk_port_macForceLinkExt_set
- * Description:
- *      Set external interface force linking configuration.
- * Input:
- *      port            - external port ID
- *      mode            - external interface mode
- *      pPortability    - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set external interface force mode properties.
- *      The external interface can be set to:
- *      - MODE_EXT_DISABLE,
- *      - MODE_EXT_RGMII,
- *      - MODE_EXT_MII_MAC,
- *      - MODE_EXT_MII_PHY,
- *      - MODE_EXT_TMII_MAC,
- *      - MODE_EXT_TMII_PHY,
- *      - MODE_EXT_GMII,
- *      - MODE_EXT_RMII_MAC,
- *      - MODE_EXT_RMII_PHY,
- *      - MODE_EXT_SGMII,
- *      - MODE_EXT_HSGMII,
- *      - MODE_EXT_1000X_100FX,
- *      - MODE_EXT_1000X,
- *      - MODE_EXT_100FX,
- */
-extern rtk_api_ret_t rtk_port_macForceLinkExt_set(rtk_port_t port, rtk_mode_ext_t mode, rtk_port_mac_ability_t *pPortability);
-
-/* Function Name:
- *      rtk_port_macForceLinkExt_get
- * Description:
- *      Set external interface force linking configuration.
- * Input:
- *      port            - external port ID
- * Output:
- *      pMode           - external interface mode
- *      pPortability    - port ability configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get external interface force mode properties.
- */
-extern rtk_api_ret_t rtk_port_macForceLinkExt_get(rtk_port_t port, rtk_mode_ext_t *pMode, rtk_port_mac_ability_t *pPortability);
-
-/* Function Name:
- *      rtk_port_macStatus_get
- * Description:
- *      Get port link status.
- * Input:
- *      port - Port id.
- * Output:
- *      pPortstatus - port ability configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get Port/PHY properties.
- */
-extern rtk_api_ret_t rtk_port_macStatus_get(rtk_port_t port, rtk_port_mac_ability_t *pPortstatus);
-
-/* Function Name:
- *      rtk_port_macLocalLoopbackEnable_set
- * Description:
- *      Set Port Local Loopback. (Redirect TX to RX.)
- * Input:
- *      port    - Port id.
- *      enable  - Loopback state, 0:disable, 1:enable
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can enable/disable Local loopback in MAC.
- *      For UTP port, This API will also enable the digital
- *      loopback bit in PHY register for sync of speed between
- *      PHY and MAC. For EXT port, users need to force the
- *      link state by themself.
- */
-extern rtk_api_ret_t rtk_port_macLocalLoopbackEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_port_macLocalLoopbackEnable_get
- * Description:
- *      Get Port Local Loopback. (Redirect TX to RX.)
- * Input:
- *      port    - Port id.
- * Output:
- *      pEnable  - Loopback state, 0:disable, 1:enable
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_port_macLocalLoopbackEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_port_phyReg_set
- * Description:
- *      Set PHY register data of the specific port.
- * Input:
- *      port    - port id.
- *      reg     - Register id
- *      regData - Register data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      This API can set PHY register data of the specific port.
- */
-extern rtk_api_ret_t rtk_port_phyReg_set(rtk_port_t port, rtk_port_phy_reg_t reg, rtk_port_phy_data_t value);
-
-/* Function Name:
- *      rtk_port_phyReg_get
- * Description:
- *      Get PHY register data of the specific port.
- * Input:
- *      port    - Port id.
- *      reg     - Register id
- * Output:
- *      pData   - Register data
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      This API can get PHY register data of the specific port.
- */
-extern rtk_api_ret_t rtk_port_phyReg_get(rtk_port_t port, rtk_port_phy_reg_t reg, rtk_port_phy_data_t *pData);
-
-/* Function Name:
- *      rtk_port_backpressureEnable_set
- * Description:
- *      Set the half duplex backpressure enable status of the specific port.
- * Input:
- *      port    - port id.
- *      enable  - Back pressure status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can set the half duplex backpressure enable status of the specific port.
- *      The half duplex backpressure enable status of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_port_backpressureEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_port_backpressureEnable_get
- * Description:
- *      Get the half duplex backpressure enable status of the specific port.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Back pressure status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get the half duplex backpressure enable status of the specific port.
- *      The half duplex backpressure enable status of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_port_backpressureEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_port_adminEnable_set
- * Description:
- *      Set port admin configuration of the specific port.
- * Input:
- *      port    - port id.
- *      enable  - Back pressure status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can set port admin configuration of the specific port.
- *      The port admin configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_port_adminEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_port_adminEnable_get
- * Description:
- *      Get port admin configurationof the specific port.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Back pressure status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get port admin configuration of the specific port.
- *      The port admin configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_port_adminEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_port_isolation_set
- * Description:
- *      Set permitted port isolation portmask
- * Input:
- *      port         - port id.
- *      pPortmask    - Permit port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      This API set the port mask that a port can trasmit packet to of each port
- *      A port can only transmit packet to ports included in permitted portmask
- */
-extern rtk_api_ret_t rtk_port_isolation_set(rtk_port_t port, rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_port_isolation_get
- * Description:
- *      Get permitted port isolation portmask
- * Input:
- *      port - Port id.
- * Output:
- *      pPortmask - Permit port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API get the port mask that a port can trasmit packet to of each port
- *      A port can only transmit packet to ports included in permitted portmask
- */
-extern rtk_api_ret_t rtk_port_isolation_get(rtk_port_t port, rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_port_rgmiiDelayExt_set
- * Description:
- *      Set RGMII interface delay value for TX and RX.
- * Input:
- *      txDelay - TX delay value, 1 for delay 2ns and 0 for no-delay
- *      rxDelay - RX delay value, 0~7 for delay setup.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set external interface 2 RGMII delay.
- *      In TX delay, there are 2 selection: no-delay and 2ns delay.
- *      In RX dekay, there are 8 steps for delay tunning. 0 for no-delay, and 7 for maximum delay.
- */
-extern rtk_api_ret_t rtk_port_rgmiiDelayExt_set(rtk_port_t port, rtk_data_t txDelay, rtk_data_t rxDelay);
-
-/* Function Name:
- *      rtk_port_rgmiiDelayExt_get
- * Description:
- *      Get RGMII interface delay value for TX and RX.
- * Input:
- *      None
- * Output:
- *      pTxDelay - TX delay value
- *      pRxDelay - RX delay value
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set external interface 2 RGMII delay.
- *      In TX delay, there are 2 selection: no-delay and 2ns delay.
- *      In RX dekay, there are 8 steps for delay tunning. 0 for n0-delay, and 7 for maximum delay.
- */
-extern rtk_api_ret_t rtk_port_rgmiiDelayExt_get(rtk_port_t port, rtk_data_t *pTxDelay, rtk_data_t *pRxDelay);
-
-/* Function Name:
- *      rtk_port_phyEnableAll_set
- * Description:
- *      Set all PHY enable status.
- * Input:
- *      enable - PHY Enable State.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can set all PHY status.
- *      The configuration of all PHY is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_port_phyEnableAll_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_port_phyEnableAll_get
- * Description:
- *      Get all PHY enable status.
- * Input:
- *      None
- * Output:
- *      pEnable - PHY Enable State.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      This API can set all PHY status.
- *      The configuration of all PHY is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_port_phyEnableAll_get(rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_port_efid_set
- * Description:
- *      Set port-based enhanced filtering database
- * Input:
- *      port - Port id.
- *      efid - Specified enhanced filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_L2_FID - Invalid fid.
- *      RT_ERR_INPUT - Invalid input parameter.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can set port-based enhanced filtering database.
- */
-extern rtk_api_ret_t rtk_port_efid_set(rtk_port_t port, rtk_data_t efid);
-
-/* Function Name:
- *      rtk_port_efid_get
- * Description:
- *      Get port-based enhanced filtering database
- * Input:
- *      port - Port id.
- * Output:
- *      pEfid - Specified enhanced filtering database.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can get port-based enhanced filtering database status.
- */
-extern rtk_api_ret_t rtk_port_efid_get(rtk_port_t port, rtk_data_t *pEfid);
-
-/* Function Name:
- *      rtk_port_phyComboPortMedia_set
- * Description:
- *      Set Combo port media type
- * Input:
- *      port    - Port id. (Should be Port 4)
- *      media   - Media (COPPER or FIBER)
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_PORT_ID          - Invalid port ID.
- * Note:
- *      The API can Set Combo port media type.
- */
-extern rtk_api_ret_t rtk_port_phyComboPortMedia_set(rtk_port_t port, rtk_port_media_t media);
-
-/* Function Name:
- *      rtk_port_phyComboPortMedia_get
- * Description:
- *      Get Combo port media type
- * Input:
- *      port    - Port id. (Should be Port 4)
- * Output:
- *      pMedia  - Media (COPPER or FIBER)
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_PORT_ID          - Invalid port ID.
- * Note:
- *      The API can Set Combo port media type.
- */
-extern rtk_api_ret_t rtk_port_phyComboPortMedia_get(rtk_port_t port, rtk_port_media_t *pMedia);
-
-/* Function Name:
- *      rtk_port_rtctEnable_set
- * Description:
- *      Enable RTCT test
- * Input:
- *      pPortmask    - Port mask of RTCT enabled port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_MASK        - Invalid port mask.
- * Note:
- *      The API can enable RTCT Test
- */
-extern rtk_api_ret_t rtk_port_rtctEnable_set(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_port_rtctDisable_set
- * Description:
- *      Disable RTCT test
- * Input:
- *      pPortmask    - Port mask of RTCT disabled port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_MASK        - Invalid port mask.
- * Note:
- *      The API can disable RTCT Test
- */
-rtk_api_ret_t rtk_port_rtctDisable_set(rtk_portmask_t *pPortmask);
-
-
-/* Function Name:
- *      rtk_port_rtctResult_get
- * Description:
- *      Get the result of RTCT test
- * Input:
- *      port        - Port ID
- * Output:
- *      pRtctResult - The result of RTCT result
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- *      RT_ERR_PHY_RTCT_NOT_FINISH  - Testing does not finish.
- * Note:
- *      The API can get RTCT test result.
- *      RTCT test may takes 4.8 seconds to finish its test at most.
- *      Thus, if this API return RT_ERR_PHY_RTCT_NOT_FINISH or
- *      other error code, the result can not be referenced and
- *      user should call this API again until this API returns
- *      a RT_ERR_OK.
- *      The result is stored at pRtctResult->ge_result
- *      pRtctResult->linkType is unused.
- *      The unit of channel length is 2.5cm. Ex. 300 means 300 * 2.5 = 750cm = 7.5M
- */
-extern rtk_api_ret_t rtk_port_rtctResult_get(rtk_port_t port, rtk_rtctResult_t *pRtctResult);
-
-/* Function Name:
- *      rtk_port_sds_reset
- * Description:
- *      Reset Serdes
- * Input:
- *      port        - Port ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API can reset Serdes
- */
-extern rtk_api_ret_t rtk_port_sds_reset(rtk_port_t port);
-
-/* Function Name:
- *      rtk_port_sgmiiLinkStatus_get
- * Description:
- *      Get SGMII status
- * Input:
- *      port        - Port ID
- * Output:
- *      pSignalDetect   - Signal detect
- *      pSync           - Sync
- *      pLink           - Link
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API can reset Serdes
- */
-extern rtk_api_ret_t rtk_port_sgmiiLinkStatus_get(rtk_port_t port, rtk_data_t *pSignalDetect, rtk_data_t *pSync, rtk_port_linkStatus_t *pLink);
-
-/* Function Name:
- *      rtk_port_sgmiiNway_set
- * Description:
- *      Configure SGMII/HSGMII port Nway state
- * Input:
- *      port        - Port ID
- *      state       - Nway state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API configure SGMII/HSGMII port Nway state
- */
-extern rtk_api_ret_t rtk_port_sgmiiNway_set(rtk_port_t port, rtk_enable_t state);
-
-/* Function Name:
- *      rtk_port_sgmiiNway_get
- * Description:
- *      Get SGMII/HSGMII port Nway state
- * Input:
- *      port        - Port ID
- * Output:
- *      pState      - Nway state
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API can get SGMII/HSGMII port Nway state
- */
-extern rtk_api_ret_t rtk_port_sgmiiNway_get(rtk_port_t port, rtk_enable_t *pState);
-
-#endif /* __RTK_API_PORT_H__ */
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/ptp.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/ptp.h
deleted file mode 100644
index 6c4aca5a58..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/ptp.h
+++ /dev/null
@@ -1,511 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes time module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_PTP_H__
-#define __RTK_API_PTP_H__
-
-/*
- * Symbol Definition
- */
-#define RTK_MAX_NUM_OF_NANO_SECOND                     0x3B9AC9FF
-#define RTK_PTP_INTR_MASK                                          0xFF
-#define RTK_MAX_NUM_OF_TPID                                    0xFFFF
-
-/* Message Type */
-typedef enum rtk_ptp_msgType_e
-{
-    PTP_MSG_TYPE_TX_SYNC = 0,
-    PTP_MSG_TYPE_TX_DELAY_REQ,
-    PTP_MSG_TYPE_TX_PDELAY_REQ,
-    PTP_MSG_TYPE_TX_PDELAY_RESP,
-    PTP_MSG_TYPE_RX_SYNC,
-    PTP_MSG_TYPE_RX_DELAY_REQ,
-    PTP_MSG_TYPE_RX_PDELAY_REQ,
-    PTP_MSG_TYPE_RX_PDELAY_RESP,
-    PTP_MSG_TYPE_END
-} rtk_ptp_msgType_t;
-
-typedef enum rtk_ptp_intType_e
-{
-    PTP_INT_TYPE_TX_SYNC = 0,
-    PTP_INT_TYPE_TX_DELAY_REQ,
-    PTP_INT_TYPE_TX_PDELAY_REQ,
-    PTP_INT_TYPE_TX_PDELAY_RESP,
-    PTP_INT_TYPE_RX_SYNC,
-    PTP_INT_TYPE_RX_DELAY_REQ,
-    PTP_INT_TYPE_RX_PDELAY_REQ,
-    PTP_INT_TYPE_RX_PDELAY_RESP,
-    PTP_INT_TYPE_ALL,
-    PTP_INT_TYPE_END
-}rtk_ptp_intType_t;
-
-typedef enum rtk_ptp_sys_adjust_e
-{
-    SYS_ADJUST_PLUS = 0,
-    SYS_ADJUST_MINUS,
-    SYS_ADJUST_END
-} rtk_ptp_sys_adjust_t;
-
-
-/* Reference Time */
-typedef struct rtk_ptp_timeStamp_s
-{
-    rtk_uint32 sec;
-    rtk_uint32 nsec;
-} rtk_ptp_timeStamp_t;
-
-typedef struct rtk_ptp_info_s
-{
-    rtk_uint32 sequenceId;
-    rtk_ptp_timeStamp_t   timeStamp;
-} rtk_ptp_info_t;
-
-typedef rtk_uint32 rtk_ptp_tpid_t;
-
-typedef rtk_uint32  rtk_ptp_intStatus_t;     /* interrupt status mask  */
-
-/*
- * Data Declaration
- */
-
-/*
- * Function Declaration
- */
-/* Function Name:
- *      rtk_time_init
- * Description:
- *      PTP function initialization.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API is used to initialize EEE status.
- */
-extern rtk_api_ret_t rtk_ptp_init(void);
-
-/* Function Name:
- *      rtk_ptp_mac_set
- * Description:
- *      Configure PTP mac address.
- * Input:
- *      mac - mac address to parser PTP packets.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_mac_set(rtk_mac_t mac);
-
-/* Function Name:
- *      rtk_ptp_mac_get
- * Description:
- *      Get PTP mac address.
- * Input:
- *      None
- * Output:
- *      pMac - mac address to parser PTP packets.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_mac_get(rtk_mac_t *pMac);
-
-/* Function Name:
- *      rtk_ptp_tpid_set
- * Description:
- *      Configure PTP accepted outer & inner tag TPID.
- * Input:
- *      outerId - Ether type of S-tag frame parsing in PTP ports.
- *      innerId - Ether type of C-tag frame parsing in PTP ports.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_tpid_set(rtk_ptp_tpid_t outerId, rtk_ptp_tpid_t innerId);
-
-/* Function Name:
- *      rtk_ptp_tpid_get
- * Description:
- *      Get PTP accepted outer & inner tag TPID.
- * Input:
- *      None
- * Output:
- *      pOuterId - Ether type of S-tag frame parsing in PTP ports.
- *      pInnerId - Ether type of C-tag frame parsing in PTP ports.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_tpid_get(rtk_ptp_tpid_t *pOuterId, rtk_ptp_tpid_t *pInnerId);
-
-/* Function Name:
- *      rtk_ptp_refTime_set
- * Description:
- *      Set the reference time of the specified device.
- * Input:
- *      timeStamp - reference timestamp value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT    - invalid input parameter
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_refTime_set(rtk_ptp_timeStamp_t timeStamp);
-
-/* Function Name:
- *      rtk_ptp_refTime_get
- * Description:
- *      Get the reference time of the specified device.
- * Input:
- * Output:
- *      pTimeStamp - pointer buffer of the reference time
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_NOT_INIT     - The module is not initial
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_refTime_get(rtk_ptp_timeStamp_t *pTimeStamp);
-
-/* Function Name:
- *      rtk_ptp_refTimeAdjust_set
- * Description:
- *      Adjust the reference time.
- * Input:
- *      unit      - unit id
- *      sign      - significant
- *      timeStamp - reference timestamp value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID  - invalid unit id
- *      RT_ERR_NOT_INIT - The module is not initial
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      sign=0 for positive adjustment, sign=1 for negative adjustment.
- */
-extern rtk_api_ret_t rtk_ptp_refTimeAdjust_set(rtk_ptp_sys_adjust_t sign, rtk_ptp_timeStamp_t timeStamp);
-
-/* Function Name:
- *      rtk_ptp_refTimeEnable_set
- * Description:
- *      Set the enable state of reference time of the specified device.
- * Input:
- *      enable - status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_refTimeEnable_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_ptp_refTimeEnable_get
- * Description:
- *      Get the enable state of reference time of the specified device.
- * Input:
- * Output:
- *      pEnable - status
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_NOT_INIT     - The module is not initial
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_refTimeEnable_get(rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_ptp_portEnable_set
- * Description:
- *      Set PTP status of the specified port.
- * Input:
- *      port   - port id
- *      enable - status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT     - invalid port id
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_portEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_ptp_portEnable_get
- * Description:
- *      Get PTP status of the specified port.
- * Input:
- *      port    - port id
- * Output:
- *      pEnable - status
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT         - invalid port id
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_portEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_ptp_portTimestamp_get
- * Description:
- *      Get PTP timstamp according to the PTP identifier on the dedicated port from the specified device.
- * Input:
- *      unit       - unit id
- *      port       - port id
- *      type       - PTP message type
- * Output:
- *      pInfo      - pointer buffer of sequence ID and timestamp
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- *      RT_ERR_INPUT        - invalid input parameter
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_portTimestamp_get( rtk_port_t port, rtk_ptp_msgType_t type, rtk_ptp_info_t *pInfo);
-
-/* Function Name:
- *      rtk_ptp_intControl_set
- * Description:
- *      Set PTP interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- *      enable - Interrupt status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The API can set PTP interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *          PTP_INT_TYPE_TX_SYNC = 0,
- *          PTP_INT_TYPE_TX_DELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_RESP,
- *          PTP_INT_TYPE_RX_SYNC,
- *          PTP_INT_TYPE_RX_DELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_RESP,
- *          PTP_INT_TYPE_ALL,
- */
-extern rtk_api_ret_t rtk_ptp_intControl_set(rtk_ptp_intType_t type, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_ptp_intControl_get
- * Description:
- *      Get PTP interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- * Output:
- *      pEnable - Interrupt status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *          PTP_INT_TYPE_TX_SYNC = 0,
- *          PTP_INT_TYPE_TX_DELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_RESP,
- *          PTP_INT_TYPE_RX_SYNC,
- *          PTP_INT_TYPE_RX_DELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_RESP,
- */
-extern rtk_api_ret_t rtk_ptp_intControl_get(rtk_ptp_intType_t type, rtk_enable_t *pEnable);
-
-
-/* Function Name:
- *      rtk_ptp_intStatus_get
- * Description:
- *      Get PTP port interrupt trigger status.
- * Input:
- *      port           - physical port
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - PORT 0  INT    (value[0] (Bit0))
- *      - PORT 1  INT    (value[0] (Bit1))
- *      - PORT 2  INT    (value[0] (Bit2))
- *      - PORT 3  INT    (value[0] (Bit3))
- *      - PORT 4  INT   (value[0] (Bit4))
-
- *
- */
-extern rtk_api_ret_t rtk_ptp_intStatus_get(rtk_ptp_intStatus_t *pStatusMask);
-
-/* Function Name:
- *      rtk_ptp_portIntStatus_set
- * Description:
- *      Set PTP port interrupt trigger status to clean.
- * Input:
- *      port           - physical port
- *      statusMask - Interrupt status bit mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- * Note:
- *      The API can clean interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - PTP_INT_TYPE_TX_SYNC              (value[0] (Bit0))
- *      - PTP_INT_TYPE_TX_DELAY_REQ      (value[0] (Bit1))
- *      - PTP_INT_TYPE_TX_PDELAY_REQ    (value[0] (Bit2))
- *      - PTP_INT_TYPE_TX_PDELAY_RESP   (value[0] (Bit3))
- *      - PTP_INT_TYPE_RX_SYNC              (value[0] (Bit4))
- *      - PTP_INT_TYPE_RX_DELAY_REQ      (value[0] (Bit5))
- *      - PTP_INT_TYPE_RX_PDELAY_REQ    (value[0] (Bit6))
- *      - PTP_INT_TYPE_RX_PDELAY_RESP   (value[0] (Bit7))
- *      The status will be cleared after execute this API.
- */
-extern rtk_api_ret_t rtk_ptp_portIntStatus_set(rtk_port_t port, rtk_ptp_intStatus_t statusMask);
-
-/* Function Name:
- *      rtk_ptp_portIntStatus_get
- * Description:
- *      Get PTP port interrupt trigger status.
- * Input:
- *      port           - physical port
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - PTP_INT_TYPE_TX_SYNC              (value[0] (Bit0))
- *      - PTP_INT_TYPE_TX_DELAY_REQ      (value[0] (Bit1))
- *      - PTP_INT_TYPE_TX_PDELAY_REQ    (value[0] (Bit2))
- *      - PTP_INT_TYPE_TX_PDELAY_RESP   (value[0] (Bit3))
- *      - PTP_INT_TYPE_RX_SYNC              (value[0] (Bit4))
- *      - PTP_INT_TYPE_RX_DELAY_REQ      (value[0] (Bit5))
- *      - PTP_INT_TYPE_RX_PDELAY_REQ    (value[0] (Bit6))
- *      - PTP_INT_TYPE_RX_PDELAY_RESP   (value[0] (Bit7))
- *
- */
-extern rtk_api_ret_t rtk_ptp_portIntStatus_get(rtk_port_t port, rtk_ptp_intStatus_t *pStatusMask);
-
-/* Function Name:
- *      rtk_ptp_portPtpTrap_set
- * Description:
- *      Set PTP packet trap of the specified port.
- * Input:
- *      port   - port id
- *      enable - status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT     - invalid port id
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_portTrap_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_ptp_portPtpEnable_get
- * Description:
- *      Get PTP packet trap of the specified port.
- * Input:
- *      port    - port id
- * Output:
- *      pEnable - status
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT         - invalid port id
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_ptp_portTrap_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-#endif /* __RTK_API_PTP_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/qos.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/qos.h
deleted file mode 100644
index 4be417486f..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/qos.h
+++ /dev/null
@@ -1,781 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes QoS module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_QOS_H__
-#define __RTK_API_QOS_H__
-
-/*
- * Data Type Declaration
- */
-#define QOS_DEFAULT_TICK_PERIOD                     (19-1)
-#define QOS_DEFAULT_BYTE_PER_TOKEN                  34
-#define QOS_DEFAULT_LK_THRESHOLD                    (34*3) /* Why use 0x400? */
-
-
-#define QOS_DEFAULT_INGRESS_BANDWIDTH               0x3FFF /* 0x3FFF => unlimit */
-#define QOS_DEFAULT_EGRESS_BANDWIDTH                0x3D08 /*( 0x3D08 + 1) * 64Kbps => 1Gbps*/
-#define QOS_DEFAULT_PREIFP                          1
-#define QOS_DEFAULT_PACKET_USED_PAGES_FC            0x60
-#define QOS_DEFAULT_PACKET_USED_FC_EN               0
-#define QOS_DEFAULT_QUEUE_BASED_FC_EN               1
-
-#define QOS_DEFAULT_PRIORITY_SELECT_PORT            8
-#define QOS_DEFAULT_PRIORITY_SELECT_1Q              0
-#define QOS_DEFAULT_PRIORITY_SELECT_ACL             0
-#define QOS_DEFAULT_PRIORITY_SELECT_DSCP            0
-
-#define QOS_DEFAULT_DSCP_MAPPING_PRIORITY           0
-
-#define QOS_DEFAULT_1Q_REMARKING_ABILITY            0
-#define QOS_DEFAULT_DSCP_REMARKING_ABILITY          0
-#define QOS_DEFAULT_QUEUE_GAP                       20
-#define QOS_DEFAULT_QUEUE_NO_MAX                    6
-#define QOS_DEFAULT_AVERAGE_PACKET_RATE             0x3FFF
-#define QOS_DEFAULT_BURST_SIZE_IN_APR               0x3F
-#define QOS_DEFAULT_PEAK_PACKET_RATE                2
-#define QOS_DEFAULT_SCHEDULER_ABILITY_APR           1     /*disable*/
-#define QOS_DEFAULT_SCHEDULER_ABILITY_PPR           1    /*disable*/
-#define QOS_DEFAULT_SCHEDULER_ABILITY_WFQ           1    /*disable*/
-
-#define QOS_WEIGHT_MAX                              127
-
-#define RTK_MAX_NUM_OF_PRIORITY                     8
-#define RTK_MAX_NUM_OF_QUEUE                        8
-
-#define RTK_PRIMAX                                             7
-#define RTK_QIDMAX                                             7
-#define RTK_DSCPMAX                                         63
-
-
-/* enum Priority Selection Index */
-typedef enum rtk_qos_priDecTbl_e
-{
-    PRIDECTBL_IDX0 = 0,
-    PRIDECTBL_IDX1,
-    PRIDECTBL_END,
-}rtk_qos_priDecTbl_t;
-
-
-/* Types of 802.1p remarking source */
-typedef enum rtk_qos_1pRmkSrc_e
-{
-    DOT1P_RMK_SRC_USER_PRI,
-    DOT1P_RMK_SRC_TAG_PRI,
-    DOT1P_RMK_SRC_END
-} rtk_qos_1pRmkSrc_t;
-
-
-/* Types of DSCP remarking source */
-typedef enum rtk_qos_dscpRmkSrc_e
-{
-    DSCP_RMK_SRC_INT_PRI,
-    DSCP_RMK_SRC_DSCP,
-    DSCP_RMK_SRC_USER_PRI,
-    DSCP_RMK_SRC_END
-} rtk_qos_dscpRmkSrc_t;
-
-
-
-
-typedef struct rtk_priority_select_s
-{
-    rtk_uint32 port_pri;
-    rtk_uint32 dot1q_pri;
-    rtk_uint32 acl_pri;
-    rtk_uint32 dscp_pri;
-    rtk_uint32 cvlan_pri;
-    rtk_uint32 svlan_pri;
-    rtk_uint32 dmac_pri;
-    rtk_uint32 smac_pri;
-} rtk_priority_select_t;
-
-typedef struct rtk_qos_pri2queue_s
-{
-    rtk_uint32 pri2queue[RTK_MAX_NUM_OF_PRIORITY];
-} rtk_qos_pri2queue_t;
-
-typedef struct rtk_qos_queue_weights_s
-{
-    rtk_uint32 weights[RTK_MAX_NUM_OF_QUEUE];
-} rtk_qos_queue_weights_t;
-
-typedef enum rtk_qos_scheduling_type_e
-{
-    WFQ = 0,        /* Weighted-Fair-Queue */
-    WRR,            /* Weighted-Round-Robin */
-    SCHEDULING_TYPE_END
-} rtk_qos_scheduling_type_t;
-
-typedef rtk_uint32  rtk_queue_num_t;    /* queue number*/
-
-/* Function Name:
- *      rtk_qos_init
- * Description:
- *      Configure Qos default settings with queue number assigment to each port.
- * Input:
- *      queueNum - Queue number of each port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_QUEUE_NUM    - Invalid queue number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API will initialize related Qos setting with queue number assigment.
- *      The queue number is from 1 to 8.
- */
-extern rtk_api_ret_t rtk_qos_init(rtk_queue_num_t queueNum);
-
-/* Function Name:
- *      rtk_qos_priSel_set
- * Description:
- *      Configure the priority order among different priority mechanism.
- * Input:
- *      index - Priority decision table index (0~1)
- *      pPriDec - Priority assign for port, dscp, 802.1p, cvlan, svlan, acl based priority decision.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_SEL_PRI_SOURCE   - Invalid priority decision source parameter.
- * Note:
- *      ASIC will follow user priority setting of mechanisms to select mapped queue priority for receiving frame.
- *      If two priority mechanisms are the same, the ASIC will chose the highest priority from mechanisms to
- *      assign queue priority to receiving frame.
- *      The priority sources are:
- *      - PRIDEC_PORT
- *      - PRIDEC_ACL
- *      - PRIDEC_DSCP
- *      - PRIDEC_1Q
- *      - PRIDEC_1AD
- *      - PRIDEC_CVLAN
- *      - PRIDEC_DA
- *      - PRIDEC_SA
- */
-extern rtk_api_ret_t rtk_qos_priSel_set(rtk_qos_priDecTbl_t index, rtk_priority_select_t *pPriDec);
-
-
-/* Function Name:
- *      rtk_qos_priSel_get
- * Description:
- *      Get the priority order configuration among different priority mechanism.
- * Input:
- *      index - Priority decision table index (0~1)
- * Output:
- *      pPriDec - Priority assign for port, dscp, 802.1p, cvlan, svlan, acl based priority decision .
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      ASIC will follow user priority setting of mechanisms to select mapped queue priority for receiving frame.
- *      If two priority mechanisms are the same, the ASIC will chose the highest priority from mechanisms to
- *      assign queue priority to receiving frame.
- *      The priority sources are:
- *      - PRIDEC_PORT,
- *      - PRIDEC_ACL,
- *      - PRIDEC_DSCP,
- *      - PRIDEC_1Q,
- *      - PRIDEC_1AD,
- *      - PRIDEC_CVLAN,
- *      - PRIDEC_DA,
- *      - PRIDEC_SA,
- */
-extern rtk_api_ret_t rtk_qos_priSel_get(rtk_qos_priDecTbl_t index, rtk_priority_select_t *pPriDec);
-
-/* Function Name:
- *      rtk_qos_1pPriRemap_set
- * Description:
- *      Configure 1Q priorities mapping to internal absolute priority.
- * Input:
- *      dot1p_pri   - 802.1p priority value.
- *      int_pri     - internal priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of 802.1Q assignment for internal asic priority, and it is used for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_qos_1pPriRemap_set(rtk_pri_t dot1p_pri, rtk_pri_t int_pri);
-
-/* Function Name:
- *      rtk_qos_1pPriRemap_get
- * Description:
- *      Get 1Q priorities mapping to internal absolute priority.
- * Input:
- *      dot1p_pri - 802.1p priority value .
- * Output:
- *      pInt_pri - internal priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_VLAN_PRIORITY    - Invalid priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of 802.1Q assigment for internal asic priority, and it is uesed for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_qos_1pPriRemap_get(rtk_pri_t dot1p_pri, rtk_pri_t *pInt_pri);
-
-
-/* Function Name:
- *      rtk_qos_1pRemarkSrcSel_set
- * Description:
- *      Set remarking source of 802.1p remarking.
- * Input:
- *      type      - remarking source
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID  - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
-
- * Note:
- *      The API can configure 802.1p remark functionality to map original 802.1p value or internal
- *      priority to TX DSCP value.
- */
-extern rtk_api_ret_t rtk_qos_1pRemarkSrcSel_set(rtk_qos_1pRmkSrc_t type);
-
-/* Function Name:
- *      rtk_qos_1pRemarkSrcSel_get
- * Description:
- *      Get remarking source of 802.1p remarking.
- * Input:
- *      none
- * Output:
- *      pType      - remarking source
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
- *      RT_ERR_NULL_POINTER     - input parameter may be null pointer
-
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_qos_1pRemarkSrcSel_get(rtk_qos_1pRmkSrc_t *pType);
-
-/* Function Name:
- *      rtk_qos_dscpPriRemap_set
- * Description:
- *      Map dscp value to internal priority.
- * Input:
- *      dscp    - Dscp value of receiving frame
- *      int_pri - internal priority value .
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid DSCP value.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The Differentiated Service Code Point is a selector for router's per-hop behaviors. As a selector, there is no implication that a numerically
- *      greater DSCP implies a better network service. As can be seen, the DSCP totally overlaps the old precedence field of TOS. So if values of
- *      DSCP are carefully chosen then backward compatibility can be achieved.
- */
-extern rtk_api_ret_t rtk_qos_dscpPriRemap_set(rtk_dscp_t dscp, rtk_pri_t int_pri);
-
-/* Function Name:
- *      rtk_qos_dscpPriRemap_get
- * Description:
- *      Get dscp value to internal priority.
- * Input:
- *      dscp - Dscp value of receiving frame
- * Output:
- *      pInt_pri - internal priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid DSCP value.
- * Note:
- *      The Differentiated Service Code Point is a selector for router's per-hop behaviors. As a selector, there is no implication that a numerically
- *      greater DSCP implies a better network service. As can be seen, the DSCP totally overlaps the old precedence field of TOS. So if values of
- *      DSCP are carefully chosen then backward compatibility can be achieved.
- */
-extern rtk_api_ret_t rtk_qos_dscpPriRemap_get(rtk_dscp_t dscp, rtk_pri_t *pInt_pri);
-
-/* Function Name:
- *      rtk_qos_portPri_set
- * Description:
- *      Configure priority usage to each port.
- * Input:
- *      port - Port id.
- *      int_pri - internal priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_SEL_PORT_PRI - Invalid port priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can set priority of port assignments for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_qos_portPri_set(rtk_port_t port, rtk_pri_t int_pri) ;
-
-/* Function Name:
- *      rtk_qos_portPri_get
- * Description:
- *      Get priority usage to each port.
- * Input:
- *      port - Port id.
- * Output:
- *      pInt_pri - internal priority value.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get priority of port assignments for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_qos_portPri_get(rtk_port_t port, rtk_pri_t *pInt_pri) ;
-
-/* Function Name:
- *      rtk_qos_queueNum_set
- * Description:
- *      Set output queue number for each port.
- * Input:
- *      port    - Port id.
- *      index   - Mapping queue number (1~8)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_QUEUE_NUM    - Invalid queue number.
- * Note:
- *      The API can set the output queue number of the specified port. The queue number is from 1 to 8.
- */
-extern rtk_api_ret_t rtk_qos_queueNum_set(rtk_port_t port, rtk_queue_num_t queue_num);
-
-/* Function Name:
- *      rtk_qos_queueNum_get
- * Description:
- *      Get output queue number.
- * Input:
- *      port - Port id.
- * Output:
- *      pQueue_num - Mapping queue number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API will return the output queue number of the specified port. The queue number is from 1 to 8.
- */
-extern rtk_api_ret_t rtk_qos_queueNum_get(rtk_port_t port, rtk_queue_num_t *pQueue_num);
-
-/* Function Name:
- *      rtk_qos_priMap_set
- * Description:
- *      Set output queue number for each port.
- * Input:
- *      queue_num   - Queue number usage.
- *      pPri2qid    - Priority mapping to queue ID.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_QUEUE_NUM        - Invalid queue number.
- *      RT_ERR_QUEUE_ID         - Invalid queue id.
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      ASIC supports priority mapping to queue with different queue number from 1 to 8.
- *      For different queue numbers usage, ASIC supports different internal available queue IDs.
- */
-extern rtk_api_ret_t rtk_qos_priMap_set(rtk_queue_num_t queue_num, rtk_qos_pri2queue_t *pPri2qid);
-
-
-/* Function Name:
- *      rtk_qos_priMap_get
- * Description:
- *      Get priority to queue ID mapping table parameters.
- * Input:
- *      queue_num - Queue number usage.
- * Output:
- *      pPri2qid - Priority mapping to queue ID.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_QUEUE_NUM    - Invalid queue number.
- * Note:
- *      The API can return the mapping queue id of the specified priority and queue number.
- *      The queue number is from 1 to 8.
- */
-extern rtk_api_ret_t rtk_qos_priMap_get(rtk_queue_num_t queue_num, rtk_qos_pri2queue_t *pPri2qid);
-
-/* Function Name:
- *      rtk_qos_schedulingQueue_set
- * Description:
- *      Set weight and type of queues in dedicated port.
- * Input:
- *      port        - Port id.
- *      pQweights   - The array of weights for WRR/WFQ queue (0 for STRICT_PRIORITY queue).
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_QUEUE_WEIGHT - Invalid queue weight.
- * Note:
- *      The API can set weight and type, strict priority or weight fair queue (WFQ) for
- *      dedicated port for using queues. If queue id is not included in queue usage,
- *      then its type and weight setting in dummy for setting. There are priorities
- *      as queue id in strict queues. It means strict queue id 5 carrying higher priority
- *      than strict queue id 4. The WFQ queue weight is from 1 to 128, and weight 0 is
- *      for strict priority queue type.
- */
-extern rtk_api_ret_t rtk_qos_schedulingQueue_set(rtk_port_t port, rtk_qos_queue_weights_t *pQweights);
-
-/* Function Name:
- *      rtk_qos_schedulingQueue_get
- * Description:
- *      Get weight and type of queues in dedicated port.
- * Input:
- *      port - Port id.
- * Output:
- *      pQweights - The array of weights for WRR/WFQ queue (0 for STRICT_PRIORITY queue).
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get weight and type, strict priority or weight fair queue (WFQ) for dedicated port for using queues.
- *      The WFQ queue weight is from 1 to 128, and weight 0 is for strict priority queue type.
- */
-extern rtk_api_ret_t rtk_qos_schedulingQueue_get(rtk_port_t port, rtk_qos_queue_weights_t *pQweights);
-
-/* Function Name:
- *      rtk_qos_1pRemarkEnable_set
- * Description:
- *      Set 1p Remarking state
- * Input:
- *      port        - Port id.
- *      enable      - State of per-port 1p Remarking
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable parameter.
- * Note:
- *      The API can enable or disable 802.1p remarking ability for whole system.
- *      The status of 802.1p remark:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_qos_1pRemarkEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_qos_1pRemarkEnable_get
- * Description:
- *      Get 802.1p remarking ability.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Status of 802.1p remark.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get 802.1p remarking ability.
- *      The status of 802.1p remark:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_qos_1pRemarkEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_qos_1pRemark_set
- * Description:
- *      Set 802.1p remarking parameter.
- * Input:
- *      int_pri     - Internal priority value.
- *      dot1p_pri   - 802.1p priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can set 802.1p parameters source priority and new priority.
- */
-extern rtk_api_ret_t rtk_qos_1pRemark_set(rtk_pri_t int_pri, rtk_pri_t dot1p_pri);
-
-/* Function Name:
- *      rtk_qos_1pRemark_get
- * Description:
- *      Get 802.1p remarking parameter.
- * Input:
- *      int_pri - Internal priority value.
- * Output:
- *      pDot1p_pri - 802.1p priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can get 802.1p remarking parameters. It would return new priority of ingress priority.
- */
-extern rtk_api_ret_t rtk_qos_1pRemark_get(rtk_pri_t int_pri, rtk_pri_t *pDot1p_pri);
-
-/* Function Name:
- *      rtk_qos_dscpRemarkEnable_set
- * Description:
- *      Set DSCP remarking ability.
- * Input:
- *      port    - Port id.
- *      enable  - status of DSCP remark.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- *      RT_ERR_ENABLE           - Invalid enable parameter.
- * Note:
- *      The API can enable or disable DSCP remarking ability for whole system.
- *      The status of DSCP remark:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_qos_dscpRemarkEnable_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_qos_dscpRemarkEnable_get
- * Description:
- *      Get DSCP remarking ability.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - status of DSCP remarking.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get DSCP remarking ability.
- *      The status of DSCP remark:
- *      - DISABLED
- *      - ENABLED
- */
-extern rtk_api_ret_t rtk_qos_dscpRemarkEnable_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_qos_dscpRemark_set
- * Description:
- *      Set DSCP remarking parameter.
- * Input:
- *      int_pri - Internal priority value.
- *      dscp    - DSCP value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid DSCP value.
- * Note:
- *      The API can set DSCP value and mapping priority.
- */
-extern rtk_api_ret_t rtk_qos_dscpRemark_set(rtk_pri_t int_pri, rtk_dscp_t dscp);
-
-/* Function Name:
- *      rtk_qos_dscpRemark_get
- * Description:
- *      Get DSCP remarking parameter.
- * Input:
- *      int_pri - Internal priority value.
- * Output:
- *      Dscp - DSCP value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can get DSCP parameters. It would return DSCP value for mapping priority.
- */
-extern rtk_api_ret_t rtk_qos_dscpRemark_get(rtk_pri_t int_pri, rtk_dscp_t *pDscp);
-
-/* Function Name:
- *      rtk_qos_dscpRemarkSrcSel_set
- * Description:
- *      Set remarking source of DSCP remarking.
- * Input:
- *      type      - remarking source
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID  - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
-
- * Note:
- *      The API can configure DSCP remark functionality to map original DSCP value or internal
- *      priority to TX DSCP value.
- */
-extern rtk_api_ret_t rtk_qos_dscpRemarkSrcSel_set(rtk_qos_dscpRmkSrc_t type);
-
-
-/* Function Name:
- *      rtk_qos_dcpRemarkSrcSel_get
- * Description:
- *      Get remarking source of DSCP remarking.
- * Input:
- *      none
- * Output:
- *      pType      - remarking source
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
- *      RT_ERR_NULL_POINTER     - input parameter may be null pointer
-
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_qos_dscpRemarkSrcSel_get(rtk_qos_dscpRmkSrc_t *pType);
-
-
-/* Function Name:
- *      rtk_qos_dscpRemark2Dscp_set
- * Description:
- *      Set DSCP to remarked DSCP mapping.
- * Input:
- *      dscp    - DSCP value
- *      rmkDscp - remarked DSCP value
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid dscp value
- * Note:
- *      dscp parameter can be DSCP value or internal priority according to configuration of API
- *      dal_apollomp_qos_dscpRemarkSrcSel_set(), because DSCP remark functionality can map original DSCP
- *      value or internal priority to TX DSCP value.
- */
-extern rtk_api_ret_t rtk_qos_dscpRemark2Dscp_set(rtk_dscp_t dscp, rtk_dscp_t rmkDscp);
-
-/* Function Name:
- *      rtk_qos_dscpRemark2Dscp_get
- * Description:
- *      Get DSCP to remarked DSCP mapping.
- * Input:
- *      dscp    - DSCP value
- * Output:
- *      pDscp   - remarked DSCP value
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid dscp value
- *      RT_ERR_NULL_POINTER     - NULL pointer
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_qos_dscpRemark2Dscp_get(rtk_dscp_t dscp, rtk_dscp_t *pDscp);
-
-/* Function Name:
- *      rtk_qos_portPriSelIndex_set
- * Description:
- *      Configure priority decision index to each port.
- * Input:
- *      port - Port id.
- *      index - priority decision index.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_ENTRY_INDEX - Invalid entry index.
- * Note:
- *      The API can set priority of port assignments for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_qos_portPriSelIndex_set(rtk_port_t port, rtk_qos_priDecTbl_t index);
-
-/* Function Name:
- *      rtk_qos_portPriSelIndex_get
- * Description:
- *      Get priority decision index from each port.
- * Input:
- *      port - Port id.
- * Output:
- *      pIndex - priority decision index.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get priority of port assignments for queue usage and packet scheduling.
- */
-extern rtk_api_ret_t rtk_qos_portPriSelIndex_get(rtk_port_t port, rtk_qos_priDecTbl_t *pIndex);
-
-#endif /* __RTK_API_QOS_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rate.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rate.h
deleted file mode 100644
index 231ed01bb0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rate.h
+++ /dev/null
@@ -1,305 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes rate module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_RATE_H__
-#define __RTK_API_RATE_H__
-
-/*
- * Include Files
- */
-//#include <rtk_types.h>
-
-/*
- * Data Type Declaration
- */
-#define RTK_MAX_METER_ID            (rtk_switch_maxMeterId_get())
-#define RTK_METER_NUM               (RTK_MAX_METER_ID + 1)
-
-typedef enum rtk_meter_type_e{
-    METER_TYPE_KBPS = 0,    /* Kbps */
-    METER_TYPE_PPS,         /* Packet per second */
-    METER_TYPE_END
-}rtk_meter_type_t;
-
-
-/*
- * Function Declaration
- */
-
- /* Rate */
-/* Function Name:
- *      rtk_rate_shareMeter_set
- * Description:
- *      Set meter configuration
- * Input:
- *      index       - shared meter index
- *      type        - shared meter type
- *      rate        - rate of share meter
- *      ifg_include - include IFG or not, ENABLE:include DISABLE:exclude
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- *      RT_ERR_RATE             - Invalid rate
- *      RT_ERR_INPUT            - Invalid input parameters
- * Note:
- *      The API can set shared meter rate and ifg include for each meter.
- *      The rate unit is 1 kbps and the range is from 8k to 1048568k if type is METER_TYPE_KBPS and
- *      the granularity of rate is 8 kbps.
- *      The rate unit is packets per second and the range is 1 ~ 0x1FFF if type is METER_TYPE_PPS.
- *      The ifg_include parameter is used
- *      for rate calculation with/without inter-frame-gap and preamble.
- */
-rtk_api_ret_t rtk_rate_shareMeter_set(rtk_meter_id_t index, rtk_meter_type_t type, rtk_rate_t rate, rtk_enable_t ifg_include);
-
-/* Function Name:
- *      rtk_rate_shareMeter_get
- * Description:
- *      Get meter configuration
- * Input:
- *      index        - shared meter index
- * Output:
- *      pType        - Meter Type
- *      pRate        - pointer of rate of share meter
- *      pIfg_include - include IFG or not, ENABLE:include DISABLE:exclude
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_shareMeter_get(rtk_meter_id_t index, rtk_meter_type_t *pType, rtk_rate_t *pRate, rtk_enable_t *pIfg_include);
-
-/* Function Name:
- *      rtk_rate_shareMeterBucket_set
- * Description:
- *      Set meter Bucket Size
- * Input:
- *      index        - shared meter index
- *      bucket_size  - Bucket Size
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_INPUT            - Error Input
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      The API can set shared meter bucket size.
- */
-extern rtk_api_ret_t rtk_rate_shareMeterBucket_set(rtk_meter_id_t index, rtk_uint32 bucket_size);
-
-/* Function Name:
- *      rtk_rate_shareMeterBucket_get
- * Description:
- *      Get meter Bucket Size
- * Input:
- *      index        - shared meter index
- * Output:
- *      pBucket_size - Bucket Size
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      The API can get shared meter bucket size.
- */
-extern rtk_api_ret_t rtk_rate_shareMeterBucket_get(rtk_meter_id_t index, rtk_uint32 *pBucket_size);
-
-/* Function Name:
- *      rtk_rate_igrBandwidthCtrlRate_set
- * Description:
- *      Set port ingress bandwidth control
- * Input:
- *      port        - Port id
- *      rate        - Rate of share meter
- *      ifg_include - include IFG or not, ENABLE:include DISABLE:exclude
- *      fc_enable   - enable flow control or not, ENABLE:use flow control DISABLE:drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid IFG parameter.
- *      RT_ERR_INBW_RATE    - Invalid ingress rate parameter.
- * Note:
- *      The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *      The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-extern rtk_api_ret_t rtk_rate_igrBandwidthCtrlRate_set( rtk_port_t port, rtk_rate_t rate,  rtk_enable_t ifg_include, rtk_enable_t fc_enable);
-
-/* Function Name:
- *      rtk_rate_igrBandwidthCtrlRate_get
- * Description:
- *      Get port ingress bandwidth control
- * Input:
- *      port - Port id
- * Output:
- *      pRate           - Rate of share meter
- *      pIfg_include    - Rate's calculation including IFG, ENABLE:include DISABLE:exclude
- *      pFc_enable      - enable flow control or not, ENABLE:use flow control DISABLE:drop
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *     The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *     The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-extern rtk_api_ret_t rtk_rate_igrBandwidthCtrlRate_get(rtk_port_t port, rtk_rate_t *pRate, rtk_enable_t *pIfg_include, rtk_enable_t *pFc_enable);
-
-/* Function Name:
- *      rtk_rate_egrBandwidthCtrlRate_set
- * Description:
- *      Set port egress bandwidth control
- * Input:
- *      port        - Port id
- *      rate        - Rate of egress bandwidth
- *      ifg_include - include IFG or not, ENABLE:include DISABLE:exclude
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_QOS_EBW_RATE - Invalid egress bandwidth/rate
- * Note:
- *     The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *     The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-extern rtk_api_ret_t rtk_rate_egrBandwidthCtrlRate_set(rtk_port_t port, rtk_rate_t rate,  rtk_enable_t ifg_includ);
-
-/* Function Name:
- *      rtk_rate_egrBandwidthCtrlRate_get
- * Description:
- *      Get port egress bandwidth control
- * Input:
- *      port - Port id
- * Output:
- *      pRate           - Rate of egress bandwidth
- *      pIfg_include    - Rate's calculation including IFG, ENABLE:include DISABLE:exclude
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *     The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *     The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-extern rtk_api_ret_t rtk_rate_egrBandwidthCtrlRate_get(rtk_port_t port, rtk_rate_t *pRate, rtk_enable_t *pIfg_include);
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlEnable_set
- * Description:
- *      Set enable status of egress bandwidth control on specified queue.
- * Input:
- *      port   - port id
- *      queue  - queue id
- *      enable - enable status of egress queue bandwidth control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_INPUT            - invalid input parameter
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rate_egrQueueBwCtrlEnable_set(rtk_port_t port, rtk_qid_t queue, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlRate_get
- * Description:
- *      Get rate of egress bandwidth control on specified queue.
- * Input:
- *      port  - port id
- *      queue - queue id
- *      pIndex - shared meter index
- * Output:
- *      pRate - pointer to rate of egress queue bandwidth control
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter id
- * Note:
- *    None.
- */
-extern rtk_api_ret_t rtk_rate_egrQueueBwCtrlEnable_get(rtk_port_t port, rtk_qid_t queue, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlRate_set
- * Description:
- *      Set rate of egress bandwidth control on specified queue.
- * Input:
- *      port  - port id
- *      queue - queue id
- *      index - shared meter index
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter id
- * Note:
- *    The actual rate control is set in shared meters.
- *    The unit of granularity is 8Kbps.
- */
-extern rtk_api_ret_t rtk_rate_egrQueueBwCtrlRate_set(rtk_port_t port, rtk_qid_t queue, rtk_meter_id_t index);
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlRate_get
- * Description:
- *      Get rate of egress bandwidth control on specified queue.
- * Input:
- *      port  - port id
- *      queue - queue id
- *      pIndex - shared meter index
- * Output:
- *      pRate - pointer to rate of egress queue bandwidth control
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter id
- * Note:
- *    The actual rate control is set in shared meters.
- *    The unit of granularity is 8Kbps.
- */
-extern rtk_api_ret_t rtk_rate_egrQueueBwCtrlRate_get(rtk_port_t port, rtk_qid_t queue, rtk_meter_id_t *pIndex);
-
-#endif /* __RTK_API_RATE_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rldp.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rldp.h
deleted file mode 100644
index 111de0c093..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rldp.h
+++ /dev/null
@@ -1,264 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : Declaration of RLDP and RLPP API
- *
- * Feature : The file have include the following module and sub-modules
- *           1) RLDP and RLPP configuration and status
- *
- */
-
-
-#ifndef __RTK_RLDP_H__
-#define __RTK_RLDP_H__
-
-
-/*
- * Include Files
- */
-
-
-/*
- * Symbol Definition
- */
-typedef enum rtk_rldp_trigger_e
-{
-    RTK_RLDP_TRIGGER_SAMOVING = 0,
-    RTK_RLDP_TRIGGER_PERIOD,
-    RTK_RLDP_TRIGGER_END
-} rtk_rldp_trigger_t;
-
-typedef enum rtk_rldp_cmpType_e
-{
-    RTK_RLDP_CMPTYPE_MAGIC = 0,     /* Compare the RLDP with magic only */
-    RTK_RLDP_CMPTYPE_MAGIC_ID,      /* Compare the RLDP with both magic + ID */
-    RTK_RLDP_CMPTYPE_END
-} rtk_rldp_cmpType_t;
-
-typedef enum rtk_rldp_loopStatus_e
-{
-    RTK_RLDP_LOOPSTS_NONE = 0,
-    RTK_RLDP_LOOPSTS_LOOPING,
-    RTK_RLDP_LOOPSTS_END
-} rtk_rldp_loopStatus_t;
-
-typedef enum rtk_rlpp_trapType_e
-{
-    RTK_RLPP_TRAPTYPE_NONE = 0,
-    RTK_RLPP_TRAPTYPE_CPU,
-    RTK_RLPP_TRAPTYPE_END
-} rtk_rlpp_trapType_t;
-
-typedef struct rtk_rldp_config_s
-{
-    rtk_enable_t        rldp_enable;
-    rtk_rldp_trigger_t trigger_mode;
-    rtk_mac_t           magic;
-    rtk_rldp_cmpType_t  compare_type;
-    rtk_uint32              interval_check; /* Checking interval for check state */
-    rtk_uint32              num_check;      /* Checking number for check state */
-    rtk_uint32              interval_loop;  /* Checking interval for loop state */
-    rtk_uint32              num_loop;       /* Checking number for loop state */
-} rtk_rldp_config_t;
-
-typedef struct rtk_rldp_portConfig_s
-{
-    rtk_enable_t        tx_enable;
-} rtk_rldp_portConfig_t;
-
-typedef struct rtk_rldp_status_s
-{
-    rtk_mac_t           id;
-} rtk_rldp_status_t;
-
-typedef struct rtk_rldp_portStatus_s
-{
-    rtk_rldp_loopStatus_t   loop_status;
-    rtk_rldp_loopStatus_t   loop_enter;
-    rtk_rldp_loopStatus_t   loop_leave;
-} rtk_rldp_portStatus_t;
-
-/*
- * Data Declaration
- */
-
-
-/*
- * Macro Declaration
- */
-
-#define RTK_RLDP_INTERVAL_MAX  0xffff
-#define RTK_RLDP_NUM_MAX       0xff
-
-
-/*
- * Function Declaration
- */
-
-/* Module Name : RLDP */
-
-
-/* Function Name:
- *      rtk_rldp_config_set
- * Description:
- *      Set RLDP module configuration
- * Input:
- *      pConfig - configuration structure of RLDP
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rldp_config_set(rtk_rldp_config_t *pConfig);
-
-
-/* Function Name:
- *      rtk_rldp_config_get
- * Description:
- *      Get RLDP module configuration
- * Input:
- *      None
- * Output:
- *      pConfig - configuration structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rldp_config_get(rtk_rldp_config_t *pConfig);
-
-
-/* Function Name:
- *      rtk_rldp_portConfig_set
- * Description:
- *      Set per port RLDP module configuration
- * Input:
- *      port   - port number to be configured
- *      pPortConfig - per port configuration structure of RLDP
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rldp_portConfig_set(rtk_port_t port, rtk_rldp_portConfig_t *pPortConfig);
-
-
-/* Function Name:
- *      rtk_rldp_portConfig_get
- * Description:
- *      Get per port RLDP module configuration
- * Input:
- *      port    - port number to be get
- * Output:
- *      pPortConfig - per port configuration structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rldp_portConfig_get(rtk_port_t port, rtk_rldp_portConfig_t *pPortConfig);
-
-
-/* Function Name:
- *      rtk_rldp_status_get
- * Description:
- *      Get RLDP module status
- * Input:
- *      None
- * Output:
- *      pStatus - status structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rldp_status_get(rtk_rldp_status_t *pStatus);
-
-
-/* Function Name:
- *      rtk_rldp_portStatus_get
- * Description:
- *      Get RLDP module status
- * Input:
- *      port    - port number to be get
- * Output:
- *      pPortStatus - per port status structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rldp_portStatus_get(rtk_port_t port, rtk_rldp_portStatus_t *pPortStatus);
-
-
-/* Function Name:
- *      rtk_rldp_portStatus_clear
- * Description:
- *      Clear RLDP module status
- * Input:
- *      port    - port number to be clear
- *      pPortStatus - per port status structure of RLDP
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      Clear operation effect loop_enter and loop_leave only, other field in
- *      the structure are don't care
- */
-extern rtk_api_ret_t rtk_rldp_portStatus_set(rtk_port_t port, rtk_rldp_portStatus_t *pPortStatus);
-
-
-/* Function Name:
- *      rtk_rldp_portLoopPair_get
- * Description:
- *      Get RLDP port loop pairs
- * Input:
- *      port    - port number to be get
- * Output:
- *      pPortmask - per port related loop ports
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_rldp_portLoopPair_get(rtk_port_t port, rtk_portmask_t *pPortmask);
-
-#endif /* __RTK_RLDP_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_error.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_error.h
deleted file mode 100644
index dc9c0bed35..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_error.h
+++ /dev/null
@@ -1,229 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : Definition the error number in the SDK.
- * Feature : error definition
- *
- */
-
-#ifndef __COMMON_RT_ERROR_H__
-#define __COMMON_RT_ERROR_H__
-
-/*
- * Include Files
- */
-
-/*
- * Data Type Declaration
- */
-typedef enum rt_error_code_e
-{
-    RT_ERR_FAILED = -1,                             /* General Error                                                                    */
-
-    /* 0x0000xxxx for common error code */
-    RT_ERR_OK = 0,                                  /* 0x00000000, OK                                                                   */
-    RT_ERR_INPUT,                                   /* 0x00000001, invalid input parameter                                              */
-    RT_ERR_UNIT_ID,                                 /* 0x00000002, invalid unit id                                                      */
-    RT_ERR_PORT_ID,                                 /* 0x00000003, invalid port id                                                      */
-    RT_ERR_PORT_MASK,                               /* 0x00000004, invalid port mask                                                    */
-    RT_ERR_PORT_LINKDOWN,                           /* 0x00000005, link down port status                                                */
-    RT_ERR_ENTRY_INDEX,                             /* 0x00000006, invalid entry index                                                  */
-    RT_ERR_NULL_POINTER,                            /* 0x00000007, input parameter is null pointer                                      */
-    RT_ERR_QUEUE_ID,                                /* 0x00000008, invalid queue id                                                     */
-    RT_ERR_QUEUE_NUM,                               /* 0x00000009, invalid queue number                                                 */
-    RT_ERR_BUSYWAIT_TIMEOUT,                        /* 0x0000000a, busy watting time out                                                */
-    RT_ERR_MAC,                                     /* 0x0000000b, invalid mac address                                                  */
-    RT_ERR_OUT_OF_RANGE,                            /* 0x0000000c, input parameter out of range                                         */
-    RT_ERR_CHIP_NOT_SUPPORTED,                      /* 0x0000000d, functions not supported by this chip model                           */
-    RT_ERR_SMI,                                     /* 0x0000000e, SMI error                                                            */
-    RT_ERR_NOT_INIT,                                /* 0x0000000f, The module is not initial                                            */
-    RT_ERR_CHIP_NOT_FOUND,                          /* 0x00000010, The chip can not found                                               */
-    RT_ERR_NOT_ALLOWED,                             /* 0x00000011, actions not allowed by the function                                  */
-    RT_ERR_DRIVER_NOT_FOUND,                        /* 0x00000012, The driver can not found                                             */
-    RT_ERR_SEM_LOCK_FAILED,                         /* 0x00000013, Failed to lock semaphore                                             */
-    RT_ERR_SEM_UNLOCK_FAILED,                       /* 0x00000014, Failed to unlock semaphore                                           */
-    RT_ERR_ENABLE,                                  /* 0x00000015, invalid enable parameter                                             */
-    RT_ERR_TBL_FULL,                                /* 0x00000016, input table full                                                     */
-
-    /* 0x0001xxxx for vlan */
-    RT_ERR_VLAN_VID = 0x00010000,                   /* 0x00010000, invalid vid                                                          */
-    RT_ERR_VLAN_PRIORITY,                           /* 0x00010001, invalid 1p priority                                                  */
-    RT_ERR_VLAN_EMPTY_ENTRY,                        /* 0x00010002, emtpy entry of vlan table                                            */
-    RT_ERR_VLAN_ACCEPT_FRAME_TYPE,                  /* 0x00010003, invalid accept frame type                                            */
-    RT_ERR_VLAN_EXIST,                              /* 0x00010004, vlan is exist                                                        */
-    RT_ERR_VLAN_ENTRY_NOT_FOUND,                    /* 0x00010005, specified vlan entry not found                                       */
-    RT_ERR_VLAN_PORT_MBR_EXIST,                     /* 0x00010006, member port exist in the specified vlan                              */
-    RT_ERR_VLAN_PROTO_AND_PORT,                     /* 0x00010008, invalid protocol and port based vlan                              */
-
-    /* 0x0002xxxx for svlan */
-    RT_ERR_SVLAN_ENTRY_INDEX = 0x00020000,          /* 0x00020000, invalid svid entry no                                                */
-    RT_ERR_SVLAN_ETHER_TYPE,                        /* 0x00020001, invalid SVLAN ether type                                             */
-    RT_ERR_SVLAN_TABLE_FULL,                        /* 0x00020002, no empty entry in SVLAN table                                        */
-    RT_ERR_SVLAN_ENTRY_NOT_FOUND,                   /* 0x00020003, specified svlan entry not found                                      */
-    RT_ERR_SVLAN_EXIST,                             /* 0x00020004, SVLAN entry is exist                                                 */
-    RT_ERR_SVLAN_VID,                               /* 0x00020005, invalid svid                                                         */
-
-    /* 0x0003xxxx for MSTP */
-    RT_ERR_MSTI = 0x00030000,                       /* 0x00030000, invalid msti                                                         */
-    RT_ERR_MSTP_STATE,                              /* 0x00030001, invalid spanning tree status                                         */
-    RT_ERR_MSTI_EXIST,                              /* 0x00030002, MSTI exist                                                           */
-    RT_ERR_MSTI_NOT_EXIST,                          /* 0x00030003, MSTI not exist                                                       */
-
-    /* 0x0004xxxx for BUCKET */
-    RT_ERR_TIMESLOT = 0x00040000,                   /* 0x00040000, invalid time slot                                                    */
-    RT_ERR_TOKEN,                                   /* 0x00040001, invalid token amount                                                 */
-    RT_ERR_RATE,                                    /* 0x00040002, invalid rate                                                         */
-    RT_ERR_TICK,                                    /* 0x00040003, invalid tick                                                 */
-
-    /* 0x0005xxxx for RMA */
-    RT_ERR_RMA_ADDR = 0x00050000,                   /* 0x00050000, invalid rma mac address                                              */
-    RT_ERR_RMA_ACTION,                              /* 0x00050001, invalid rma action                                                   */
-
-    /* 0x0006xxxx for L2 */
-    RT_ERR_L2_HASH_KEY = 0x00060000,                /* 0x00060000, invalid L2 Hash key                                                  */
-    RT_ERR_L2_HASH_INDEX,                           /* 0x00060001, invalid L2 Hash index                                                */
-    RT_ERR_L2_CAM_INDEX,                            /* 0x00060002, invalid L2 CAM index                                                 */
-    RT_ERR_L2_ENRTYSEL,                             /* 0x00060003, invalid EntrySel                                                     */
-    RT_ERR_L2_INDEXTABLE_INDEX,                     /* 0x00060004, invalid L2 index table(=portMask table) index                        */
-    RT_ERR_LIMITED_L2ENTRY_NUM,                     /* 0x00060005, invalid limited L2 entry number                                      */
-    RT_ERR_L2_AGGREG_PORT,                          /* 0x00060006, this aggregated port is not the lowest physical
-                                                                   port of its aggregation group                                        */
-    RT_ERR_L2_FID,                                  /* 0x00060007, invalid fid                                                          */
-    RT_ERR_L2_VID,                                 /* 0x00060008, invalid cvid                                                         */
-    RT_ERR_L2_NO_EMPTY_ENTRY,                       /* 0x00060009, no empty entry in L2 table                                           */
-    RT_ERR_L2_ENTRY_NOTFOUND,                       /* 0x0006000a, specified entry not found                                            */
-    RT_ERR_L2_INDEXTBL_FULL,                        /* 0x0006000b, the L2 index table is full                                           */
-    RT_ERR_L2_INVALID_FLOWTYPE,                     /* 0x0006000c, invalid L2 flow type                                                 */
-    RT_ERR_L2_L2UNI_PARAM,                          /* 0x0006000d, invalid L2 unicast parameter                                         */
-    RT_ERR_L2_L2MULTI_PARAM,                        /* 0x0006000e, invalid L2 multicast parameter                                       */
-    RT_ERR_L2_IPMULTI_PARAM,                        /* 0x0006000f, invalid L2 ip multicast parameter                                    */
-    RT_ERR_L2_PARTIAL_HASH_KEY,                     /* 0x00060010, invalid L2 partial Hash key                                          */
-    RT_ERR_L2_EMPTY_ENTRY,                          /* 0x00060011, the entry is empty(invalid)                                          */
-    RT_ERR_L2_FLUSH_TYPE,                           /* 0x00060012, the flush type is invalid                                            */
-    RT_ERR_L2_NO_CPU_PORT,                          /* 0x00060013, CPU port not exist                                                   */
-
-    /* 0x0007xxxx for FILTER (PIE) */
-    RT_ERR_FILTER_BLOCKNUM = 0x00070000,            /* 0x00070000, invalid block number                                                 */
-    RT_ERR_FILTER_ENTRYIDX,                         /* 0x00070001, invalid entry index                                                  */
-    RT_ERR_FILTER_CUTLINE,                          /* 0x00070002, invalid cutline value                                                */
-    RT_ERR_FILTER_FLOWTBLBLOCK,                     /* 0x00070003, block belongs to flow table                                          */
-    RT_ERR_FILTER_INACLBLOCK,                       /* 0x00070004, block belongs to ingress ACL                                         */
-    RT_ERR_FILTER_ACTION,                           /* 0x00070005, action doesn't consist to entry type                                 */
-    RT_ERR_FILTER_INACL_RULENUM,                    /* 0x00070006, invalid ACL rulenum                                                  */
-    RT_ERR_FILTER_INACL_TYPE,                       /* 0x00070007, entry type isn't an ingress ACL rule                                 */
-    RT_ERR_FILTER_INACL_EXIST,                      /* 0x00070008, ACL entry is already exit                                            */
-    RT_ERR_FILTER_INACL_EMPTY,                      /* 0x00070009, ACL entry is empty                                                   */
-    RT_ERR_FILTER_FLOWTBL_TYPE,                     /* 0x0007000a, entry type isn't an flow table rule                                  */
-    RT_ERR_FILTER_FLOWTBL_RULENUM,                  /* 0x0007000b, invalid flow table rulenum                                           */
-    RT_ERR_FILTER_FLOWTBL_EMPTY,                    /* 0x0007000c, flow table entry is empty                                            */
-    RT_ERR_FILTER_FLOWTBL_EXIST,                    /* 0x0007000d, flow table entry is already exist                                    */
-    RT_ERR_FILTER_METER_ID,                         /* 0x0007000e, invalid metering id                                                  */
-    RT_ERR_FILTER_LOG_ID,                           /* 0x0007000f, invalid log id                                                       */
-    RT_ERR_FILTER_INACL_NONE_BEGIN_IDX,             /* 0x00070010, entry index is not starting index of a group of rules                */
-    RT_ERR_FILTER_INACL_ACT_NOT_SUPPORT,            /* 0x00070011, action not support                                                    */
-    RT_ERR_FILTER_INACL_RULE_NOT_SUPPORT,           /* 0x00070012, rule not support                                                   */
-
-    /* 0x0008xxxx for ACL Rate Limit */
-    RT_ERR_ACLRL_HTHR = 0x00080000,                 /* 0x00080000, invalid high threshold                                               */
-    RT_ERR_ACLRL_TIMESLOT,                          /* 0x00080001, invalid time slot                                                    */
-    RT_ERR_ACLRL_TOKEN,                             /* 0x00080002, invalid token amount                                                 */
-    RT_ERR_ACLRL_RATE,                              /* 0x00080003, invalid rate                                                         */
-
-    /* 0x0009xxxx for Link aggregation */
-    RT_ERR_LA_CPUPORT = 0x00090000,                 /* 0x00090000, CPU port can not be aggregated port                                  */
-    RT_ERR_LA_TRUNK_ID,                             /* 0x00090001, invalid trunk id                                                     */
-    RT_ERR_LA_PORTMASK,                             /* 0x00090002, invalid port mask                                                    */
-    RT_ERR_LA_HASHMASK,                             /* 0x00090003, invalid hash mask                                                    */
-    RT_ERR_LA_DUMB,                                 /* 0x00090004, this API should be used in 802.1ad dumb mode                         */
-    RT_ERR_LA_PORTNUM_DUMB,                         /* 0x00090005, it can only aggregate at most four ports when 802.1ad dumb mode      */
-    RT_ERR_LA_PORTNUM_NORMAL,                       /* 0x00090006, it can only aggregate at most eight ports when 802.1ad normal mode   */
-    RT_ERR_LA_MEMBER_OVERLAP,                       /* 0x00090007, the specified port mask is overlapped with other group               */
-    RT_ERR_LA_NOT_MEMBER_PORT,                      /* 0x00090008, the port is not a member port of the trunk                           */
-    RT_ERR_LA_TRUNK_NOT_EXIST,                      /* 0x00090009, the trunk doesn't exist                                              */
-
-
-    /* 0x000axxxx for storm filter */
-    RT_ERR_SFC_TICK_PERIOD = 0x000a0000,            /* 0x000a0000, invalid SFC tick period                                              */
-    RT_ERR_SFC_UNKNOWN_GROUP,                       /* 0x000a0001, Unknown Storm filter group                                           */
-
-    /* 0x000bxxxx for pattern match */
-    RT_ERR_PM_MASK = 0x000b0000,                    /* 0x000b0000, invalid pattern length. Pattern length should be 8                   */
-    RT_ERR_PM_LENGTH,                               /* 0x000b0001, invalid pattern match mask, first byte must care                     */
-    RT_ERR_PM_MODE,                                 /* 0x000b0002, invalid pattern match mode                                           */
-
-    /* 0x000cxxxx for input bandwidth control */
-    RT_ERR_INBW_TICK_PERIOD = 0x000c0000,           /* 0x000c0000, invalid tick period for input bandwidth control                      */
-    RT_ERR_INBW_TOKEN_AMOUNT,                       /* 0x000c0001, invalid amount of token for input bandwidth control                  */
-    RT_ERR_INBW_FCON_VALUE,                         /* 0x000c0002, invalid flow control ON threshold value for input bandwidth control  */
-    RT_ERR_INBW_FCOFF_VALUE,                        /* 0x000c0003, invalid flow control OFF threshold value for input bandwidth control */
-    RT_ERR_INBW_FC_ALLOWANCE,                       /* 0x000c0004, invalid allowance of incomming packet for input bandwidth control    */
-    RT_ERR_INBW_RATE,                               /* 0x000c0005, invalid input bandwidth                                              */
-
-    /* 0x000dxxxx for QoS */
-    RT_ERR_QOS_1P_PRIORITY = 0x000d0000,            /* 0x000d0000, invalid 802.1P priority                                              */
-    RT_ERR_QOS_DSCP_VALUE,                          /* 0x000d0001, invalid DSCP value                                                   */
-    RT_ERR_QOS_INT_PRIORITY,                        /* 0x000d0002, invalid internal priority                                            */
-    RT_ERR_QOS_SEL_DSCP_PRI,                        /* 0x000d0003, invalid DSCP selection priority                                      */
-    RT_ERR_QOS_SEL_PORT_PRI,                        /* 0x000d0004, invalid port selection priority                                      */
-    RT_ERR_QOS_SEL_IN_ACL_PRI,                      /* 0x000d0005, invalid ingress ACL selection priority                               */
-    RT_ERR_QOS_SEL_CLASS_PRI,                       /* 0x000d0006, invalid classifier selection priority                                */
-    RT_ERR_QOS_EBW_RATE,                            /* 0x000d0007, invalid egress bandwidth rate                                        */
-    RT_ERR_QOS_SCHE_TYPE,                           /* 0x000d0008, invalid QoS scheduling type                                          */
-    RT_ERR_QOS_QUEUE_WEIGHT,                        /* 0x000d0009, invalid Queue weight                                                 */
-    RT_ERR_QOS_SEL_PRI_SOURCE,                      /* 0x000d000a, invalid selection of priority source                                                 */
-
-    /* 0x000exxxx for port ability */
-    RT_ERR_PHY_PAGE_ID = 0x000e0000,                /* 0x000e0000, invalid PHY page id                                                  */
-    RT_ERR_PHY_REG_ID,                              /* 0x000e0001, invalid PHY reg id                                                   */
-    RT_ERR_PHY_DATAMASK,                            /* 0x000e0002, invalid PHY data mask                                                */
-    RT_ERR_PHY_AUTO_NEGO_MODE,                      /* 0x000e0003, invalid PHY auto-negotiation mode*/
-    RT_ERR_PHY_SPEED,                               /* 0x000e0004, invalid PHY speed setting                                            */
-    RT_ERR_PHY_DUPLEX,                              /* 0x000e0005, invalid PHY duplex setting                                           */
-    RT_ERR_PHY_FORCE_ABILITY,                       /* 0x000e0006, invalid PHY force mode ability parameter                             */
-    RT_ERR_PHY_FORCE_1000,                          /* 0x000e0007, invalid PHY force mode 1G speed setting                              */
-    RT_ERR_PHY_TXRX,                                /* 0x000e0008, invalid PHY tx/rx                                                    */
-    RT_ERR_PHY_ID,                                  /* 0x000e0009, invalid PHY id                                                       */
-    RT_ERR_PHY_RTCT_NOT_FINISH,                     /* 0x000e000a, PHY RTCT in progress                                                 */
-
-    /* 0x000fxxxx for mirror */
-    RT_ERR_MIRROR_DIRECTION = 0x000f0000,           /* 0x000f0000, invalid error mirror direction                                       */
-    RT_ERR_MIRROR_SESSION_FULL,                     /* 0x000f0001, mirroring session is full                                            */
-    RT_ERR_MIRROR_SESSION_NOEXIST,                  /* 0x000f0002, mirroring session not exist                                          */
-    RT_ERR_MIRROR_PORT_EXIST,                       /* 0x000f0003, mirroring port already exists                                        */
-    RT_ERR_MIRROR_PORT_NOT_EXIST,                   /* 0x000f0004, mirroring port does not exists                                       */
-    RT_ERR_MIRROR_PORT_FULL,                        /* 0x000f0005, Exceeds maximum number of supported mirroring port                   */
-
-    /* 0x0010xxxx for stat */
-    RT_ERR_STAT_INVALID_GLOBAL_CNTR = 0x00100000,   /* 0x00100000, Invalid Global Counter                                               */
-    RT_ERR_STAT_INVALID_PORT_CNTR,                  /* 0x00100001, Invalid Port Counter                                                 */
-    RT_ERR_STAT_GLOBAL_CNTR_FAIL,                   /* 0x00100002, Could not retrieve/reset Global Counter                              */
-    RT_ERR_STAT_PORT_CNTR_FAIL,                     /* 0x00100003, Could not retrieve/reset Port Counter                                */
-    RT_ERR_STAT_INVALID_CNTR,                       /* 0x00100004, Invalid Counter                                                      */
-    RT_ERR_STAT_CNTR_FAIL,                          /* 0x00100005, Could not retrieve/reset Counter                                     */
-
-    /* 0x0011xxxx for dot1x */
-    RT_ERR_DOT1X_INVALID_DIRECTION = 0x00110000,    /* 0x00110000, Invalid Authentication Direction                                     */
-    RT_ERR_DOT1X_PORTBASEDPNEN,                     /* 0x00110001, Port-based enable port error                                         */
-    RT_ERR_DOT1X_PORTBASEDAUTH,                     /* 0x00110002, Port-based auth port error                                           */
-    RT_ERR_DOT1X_PORTBASEDOPDIR,                    /* 0x00110003, Port-based opdir error                                               */
-    RT_ERR_DOT1X_MACBASEDPNEN,                      /* 0x00110004, MAC-based enable port error                                          */
-    RT_ERR_DOT1X_MACBASEDOPDIR,                     /* 0x00110005, MAC-based opdir error                                                */
-    RT_ERR_DOT1X_PROC,                              /* 0x00110006, unauthorized behavior error                                          */
-    RT_ERR_DOT1X_GVLANIDX,                          /* 0x00110007, guest vlan index error                                               */
-    RT_ERR_DOT1X_GVLANTALK,                         /* 0x00110008, guest vlan OPDIR error                                               */
-    RT_ERR_DOT1X_MAC_PORT_MISMATCH,                 /* 0x00110009, Auth MAC and port mismatch eror                                      */
-
-    RT_ERR_END                                       /* The symbol is the latest symbol                                                  */
-} rt_error_code_t;
-
-
-#endif /* __COMMON_RT_ERROR_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_hal.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_hal.h
deleted file mode 100644
index 6ddb23f2ed..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_hal.h
+++ /dev/null
@@ -1,44 +0,0 @@
-#ifndef __RTK_HAL_H__
-#define __RTK_HAL_H__
-#include "ra_ioctl.h"
-
-#define RTK_SW_VID_RANGE        16
-void rtk_hal_switch_init(void);
-void rtk_hal_dump_mib(void);
-void rtk_hal_dump_full_mib(void);
-int rtk_hal_dump_vlan(void);
-void rtk_hal_clear_vlan(void);
-int rtk_hal_set_vlan(struct ra_switch_ioctl_data *data);
-int rtk_hal_set_ingress_rate(struct ra_switch_ioctl_data *data);
-int rtk_hal_set_egress_rate(struct ra_switch_ioctl_data *data);
-void rtk_hal_dump_table(void);
-void rtk_hal_clear_table(void);
-void rtk_hal_get_phy_status(struct ra_switch_ioctl_data *data);
-void rtk_hal_set_port_mirror(struct ra_switch_ioctl_data *data);
-void rtk_hal_read_reg(struct ra_switch_ioctl_data *data);
-void rtk_hal_write_reg(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_en(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_set_table2type(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_get_table2type(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_set_port2table(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_get_port2table(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_set_port2pri(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_get_port2pri(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_set_dscp2pri(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_get_dscp2pri(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_set_pri2queue(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_get_pri2queue(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_set_queue_weight(struct ra_switch_ioctl_data *data);
-void rtk_hal_qos_get_queue_weight(struct ra_switch_ioctl_data *data);
-void rtk_hal_enable_igmpsnoop(struct ra_switch_ioctl_data *data);
-void rtk_hal_disable_igmpsnoop(void);
-void rtk_hal_set_phy_test_mode(struct ra_switch_ioctl_data *data);
-void rtk_hal_get_phy_reg(struct ra_switch_ioctl_data *data);
-void rtk_hal_set_phy_reg(struct ra_switch_ioctl_data *data);
-void rtk_hal_vlan_tag(struct ra_switch_ioctl_data *data);
-void rtk_hal_vlan_portpvid_set(rtk_port_t port, rtk_vlan_t pvid, rtk_pri_t priority);
-void rtk_hal_add_table(struct ra_switch_ioctl_data *data);
-void rtk_hal_del_table(struct ra_switch_ioctl_data *data);
-void rtk_hal_vlan_mode(struct ra_switch_ioctl_data *data);
-void rtk_hal_set_port_trunk(struct ra_switch_ioctl_data *data);
-#endif
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_switch.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_switch.h
deleted file mode 100644
index b0ca13682c..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_switch.h
+++ /dev/null
@@ -1,737 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76336 $
- * $Date: 2017-03-09 10:41:21 +0800 (週四, 09 三月 2017) $
- *
- * Purpose : RTK switch high-level API
- * Feature : Here is a list of all functions and variables in this module.
- *
- */
-
-#ifndef __RTK_SWITCH_H__
-#define __RTK_SWITCH_H__
-
-#include <rtk_types.h>
-
-#define UNDEFINE_PHY_PORT   (0xFF)
-#define RTK_SWITCH_PORT_NUM (32)
-
-#define MAXPKTLEN_CFG_ID_MAX (1)
-
-#define RTK_SWITCH_MAX_PKTLEN (0x3FFF)
-
-typedef enum init_state_e
-{
-    INIT_NOT_COMPLETED = 0,
-    INIT_COMPLETED,
-    INIT_STATE_END
-} init_state_t;
-
-typedef enum switch_chip_e
-{
-    CHIP_RTL8367C = 0,
-    CHIP_RTL8370B,
-    CHIP_RTL8364B,
-    CHIP_RTL8363SC_VB,
-    CHIP_END
-}switch_chip_t;
-
-typedef enum port_type_e
-{
-    UTP_PORT = 0,
-    EXT_PORT,
-    UNKNOWN_PORT = 0xFF,
-    PORT_TYPE_END
-}port_type_t;
-
-typedef struct rtk_switch_halCtrl_s
-{
-    switch_chip_t   switch_type;
-    rtk_uint32      l2p_port[RTK_SWITCH_PORT_NUM];
-    rtk_uint32      p2l_port[RTK_SWITCH_PORT_NUM];
-    port_type_t     log_port_type[RTK_SWITCH_PORT_NUM];
-    rtk_uint32      ptp_port[RTK_SWITCH_PORT_NUM];
-    rtk_uint32      valid_portmask;
-    rtk_uint32      valid_utp_portmask;
-    rtk_uint32      valid_ext_portmask;
-    rtk_uint32      valid_cpu_portmask;
-    rtk_uint32      min_phy_port;
-    rtk_uint32      max_phy_port;
-    rtk_uint32      phy_portmask;
-    rtk_uint32      combo_logical_port;
-    rtk_uint32      hsg_logical_port;
-    rtk_uint32      sg_logical_portmask;
-    rtk_uint32      max_meter_id;
-    rtk_uint32      max_lut_addr_num;
-    rtk_uint32      trunk_group_mask;
-
-}rtk_switch_halCtrl_t;
-
-typedef enum rtk_switch_maxPktLen_linkSpeed_e {
-     MAXPKTLEN_LINK_SPEED_FE = 0,
-     MAXPKTLEN_LINK_SPEED_GE,
-     MAXPKTLEN_LINK_SPEED_END,
-} rtk_switch_maxPktLen_linkSpeed_t;
-
-
-/* UTIL MACRO */
-#define RTK_CHK_INIT_STATE()                                \
-    do                                                      \
-    {                                                       \
-        if(rtk_switch_initialState_get() != INIT_COMPLETED) \
-        {                                                   \
-            return RT_ERR_NOT_INIT;                         \
-        }                                                   \
-    }while(0)
-
-#define RTK_CHK_PORT_VALID(__port__)                            \
-    do                                                          \
-    {                                                           \
-        if(rtk_switch_logicalPortCheck(__port__) != RT_ERR_OK)  \
-        {                                                       \
-            return RT_ERR_PORT_ID;                              \
-        }                                                       \
-    }while(0)
-
-#define RTK_CHK_PORT_IS_UTP(__port__)                           \
-    do                                                          \
-    {                                                           \
-        if(rtk_switch_isUtpPort(__port__) != RT_ERR_OK)         \
-        {                                                       \
-            return RT_ERR_PORT_ID;                              \
-        }                                                       \
-    }while(0)
-
-#define RTK_CHK_PORT_IS_EXT(__port__)                           \
-    do                                                          \
-    {                                                           \
-        if(rtk_switch_isExtPort(__port__) != RT_ERR_OK)         \
-        {                                                       \
-            return RT_ERR_PORT_ID;                              \
-        }                                                       \
-    }while(0)
-
-#define RTK_CHK_PORT_IS_COMBO(__port__)                         \
-    do                                                          \
-    {                                                           \
-        if(rtk_switch_isComboPort(__port__) != RT_ERR_OK)       \
-        {                                                       \
-            return RT_ERR_PORT_ID;                              \
-        }                                                       \
-    }while(0)
-
-#define RTK_CHK_PORT_IS_PTP(__port__)                           \
-    do                                                          \
-    {                                                           \
-        if(rtk_switch_isPtpPort(__port__) != RT_ERR_OK)         \
-        {                                                       \
-            return RT_ERR_PORT_ID;                              \
-        }                                                       \
-    }while(0)
-
-#define RTK_CHK_PORTMASK_VALID(__portmask__)                        \
-    do                                                              \
-    {                                                               \
-        if(rtk_switch_isPortMaskValid(__portmask__) != RT_ERR_OK)   \
-        {                                                           \
-            return RT_ERR_PORT_MASK;                                \
-        }                                                           \
-    }while(0)
-
-#define RTK_CHK_PORTMASK_VALID_ONLY_UTP(__portmask__)               \
-    do                                                              \
-    {                                                               \
-        if(rtk_switch_isPortMaskUtp(__portmask__) != RT_ERR_OK)     \
-        {                                                           \
-            return RT_ERR_PORT_MASK;                                \
-        }                                                           \
-    }while(0)
-
-#define RTK_CHK_PORTMASK_VALID_ONLY_EXT(__portmask__)               \
-    do                                                              \
-    {                                                               \
-        if(rtk_switch_isPortMaskExt(__portmask__) != RT_ERR_OK)     \
-        {                                                           \
-            return RT_ERR_PORT_MASK;                                \
-        }                                                           \
-    }while(0)
-
-#define RTK_CHK_TRUNK_GROUP_VALID(__grpId__)                        \
-    do                                                              \
-    {                                                               \
-        if(rtk_switch_isValidTrunkGrpId(__grpId__) != RT_ERR_OK)    \
-        {                                                           \
-            return RT_ERR_LA_TRUNK_ID;                              \
-        }                                                           \
-    }while(0)
-
-#define RTK_PORTMASK_IS_PORT_SET(__portmask__, __port__)    (((__portmask__).bits[0] & (0x00000001 << __port__)) ? 1 : 0)
-#define RTK_PORTMASK_IS_EMPTY(__portmask__)                 (((__portmask__).bits[0] == 0) ? 1 : 0)
-#define RTK_PORTMASK_CLEAR(__portmask__)                    ((__portmask__).bits[0] = 0)
-#define RTK_PORTMASK_PORT_SET(__portmask__, __port__)       ((__portmask__).bits[0] |= (0x00000001 << __port__))
-#define RTK_PORTMASK_PORT_CLEAR(__portmask__, __port__)     ((__portmask__).bits[0] &= ~(0x00000001 << __port__))
-#define RTK_PORTMASK_ALLPORT_SET(__portmask__)              (rtk_switch_logPortMask_get(&__portmask__))
-#define RTK_PORTMASK_SCAN(__portmask__, __port__)           for(__port__ = 0; __port__ < RTK_SWITCH_PORT_NUM; __port__++)  if(RTK_PORTMASK_IS_PORT_SET(__portmask__, __port__))
-#define RTK_PORTMASK_COMPARE(__portmask_A__, __portmask_B__)    ((__portmask_A__).bits[0] - (__portmask_B__).bits[0])
-
-#define RTK_SCAN_ALL_PHY_PORTMASK(__port__)                 for(__port__ = 0; __port__ < RTK_SWITCH_PORT_NUM; __port__++)  if( (rtk_switch_phyPortMask_get() & (0x00000001 << __port__)))
-#define RTK_SCAN_ALL_LOG_PORT(__port__)                     for(__port__ = 0; __port__ < RTK_SWITCH_PORT_NUM; __port__++)  if( rtk_switch_logicalPortCheck(__port__) == RT_ERR_OK)
-#define RTK_SCAN_ALL_LOG_PORTMASK(__portmask__)             for((__portmask__).bits[0] = 0; (__portmask__).bits[0] < 0x7FFFF; (__portmask__).bits[0]++)  if( rtk_switch_isPortMaskValid(&__portmask__) == RT_ERR_OK)
-
-/* Port mask defination */
-#define RTK_PHY_PORTMASK_ALL                                (rtk_switch_phyPortMask_get())
-
-/* Port defination*/
-#define RTK_MAX_LOGICAL_PORT_ID                             (rtk_switch_maxLogicalPort_get())
-
-/* Function Name:
- *      rtk_switch_probe
- * Description:
- *      Probe switch
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Switch probed
- *      RT_ERR_FAILED   - Switch Unprobed.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_probe(switch_chip_t *pSwitchChip);
-
-/* Function Name:
- *      rtk_switch_initialState_set
- * Description:
- *      Set initial status
- * Input:
- *      state   - Initial state;
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Initialized
- *      RT_ERR_FAILED   - Uninitialized
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_initialState_set(init_state_t state);
-
-/* Function Name:
- *      rtk_switch_initialState_get
- * Description:
- *      Get initial status
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      INIT_COMPLETED     - Initialized
- *      INIT_NOT_COMPLETED - Uninitialized
- * Note:
- *
- */
-extern init_state_t rtk_switch_initialState_get(void);
-
-/* Function Name:
- *      rtk_switch_logicalPortCheck
- * Description:
- *      Check logical port ID.
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is correct
- *      RT_ERR_FAILED   - Port ID is not correct
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_logicalPortCheck(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_isUtpPort
- * Description:
- *      Check is logical port a UTP port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a UTP port
- *      RT_ERR_FAILED   - Port ID is not a UTP port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isUtpPort(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_isExtPort
- * Description:
- *      Check is logical port a Extension port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a EXT port
- *      RT_ERR_FAILED   - Port ID is not a EXT port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isExtPort(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_isHsgPort
- * Description:
- *      Check is logical port a HSG port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a HSG port
- *      RT_ERR_FAILED   - Port ID is not a HSG port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isHsgPort(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_isSgmiiPort
- * Description:
- *      Check is logical port a SGMII port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a SGMII port
- *      RT_ERR_FAILED   - Port ID is not a SGMII port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isSgmiiPort(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_isCPUPort
- * Description:
- *      Check is logical port a CPU port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a CPU port
- *      RT_ERR_FAILED   - Port ID is not a CPU port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isCPUPort(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_isComboPort
- * Description:
- *      Check is logical port a Combo port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a combo port
- *      RT_ERR_FAILED   - Port ID is not a combo port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isComboPort(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_ComboPort_get
- * Description:
- *      Get Combo port ID
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      Port ID of combo port
- * Note:
- *
- */
-extern rtk_uint32 rtk_switch_ComboPort_get(void);
-
-/* Function Name:
- *      rtk_switch_isPtpPort
- * Description:
- *      Check is logical port a PTP port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a PTP port
- *      RT_ERR_FAILED   - Port ID is not a PTP port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isPtpPort(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_port_L2P_get
- * Description:
- *      Get physical port ID
- * Input:
- *      logicalPort       - logical port ID
- * Output:
- *      None
- * Return:
- *      Physical port ID
- * Note:
- *
- */
-extern rtk_uint32 rtk_switch_port_L2P_get(rtk_port_t logicalPort);
-
-/* Function Name:
- *      rtk_switch_port_P2L_get
- * Description:
- *      Get logical port ID
- * Input:
- *      physicalPort       - physical port ID
- * Output:
- *      None
- * Return:
- *      logical port ID
- * Note:
- *
- */
-extern rtk_port_t rtk_switch_port_P2L_get(rtk_uint32 physicalPort);
-
-/* Function Name:
- *      rtk_switch_isPortMaskValid
- * Description:
- *      Check portmask is valid or not
- * Input:
- *      pPmask       - logical port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - port mask is valid
- *      RT_ERR_FAILED       - port mask is not valid
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isPortMaskValid(rtk_portmask_t *pPmask);
-
-/* Function Name:
- *      rtk_switch_isPortMaskUtp
- * Description:
- *      Check all ports in portmask are only UTP port
- * Input:
- *      pPmask       - logical port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Only UTP port in port mask
- *      RT_ERR_FAILED       - Not only UTP port in port mask
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isPortMaskUtp(rtk_portmask_t *pPmask);
-
-/* Function Name:
- *      rtk_switch_isPortMaskExt
- * Description:
- *      Check all ports in portmask are only EXT port
- * Input:
- *      pPmask       - logical port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Only EXT port in port mask
- *      RT_ERR_FAILED       - Not only EXT port in port mask
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_isPortMaskExt(rtk_portmask_t *pPmask);
-
-/* Function Name:
- *      rtk_switch_portmask_L2P_get
- * Description:
- *      Get physicl portmask from logical portmask
- * Input:
- *      pLogicalPmask       - logical port mask
- * Output:
- *      pPhysicalPortmask   - physical port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- *      RT_ERR_PORT_MASK    - Error port mask
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_portmask_L2P_get(rtk_portmask_t *pLogicalPmask, rtk_uint32 *pPhysicalPortmask);
-
-/* Function Name:
- *      rtk_switch_portmask_P2L_get
- * Description:
- *      Get logical portmask from physical portmask
- * Input:
- *      physicalPortmask    - physical port mask
- * Output:
- *      pLogicalPmask       - logical port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- *      RT_ERR_PORT_MASK    - Error port mask
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_switch_portmask_P2L_get(rtk_uint32 physicalPortmask, rtk_portmask_t *pLogicalPmask);
-
-/* Function Name:
- *      rtk_switch_phyPortMask_get
- * Description:
- *      Get physical portmask
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      0x00                - Not Initialize
- *      Other value         - Physical port mask
- * Note:
- *
- */
-rtk_uint32 rtk_switch_phyPortMask_get(void);
-
-/* Function Name:
- *      rtk_switch_logPortMask_get
- * Description:
- *      Get Logical portmask
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_logPortMask_get(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_switch_init
- * Description:
- *      Set chip to default configuration enviroment
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API can set chip registers to default configuration for different release chip model.
- */
-extern rtk_api_ret_t rtk_switch_init(void);
-
-/* Function Name:
- *      rtk_switch_portMaxPktLen_set
- * Description:
- *      Set Max packet length
- * Input:
- *      port    - Port ID
- *      speed   - Speed
- *      cfgId   - Configuration ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-extern rtk_api_ret_t rtk_switch_portMaxPktLen_set(rtk_port_t port, rtk_switch_maxPktLen_linkSpeed_t speed, rtk_uint32 cfgId);
-
-/* Function Name:
- *      rtk_switch_portMaxPktLen_get
- * Description:
- *      Get Max packet length
- * Input:
- *      port    - Port ID
- *      speed   - Speed
- * Output:
- *      pCfgId  - Configuration ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-extern rtk_api_ret_t rtk_switch_portMaxPktLen_get(rtk_port_t port, rtk_switch_maxPktLen_linkSpeed_t speed, rtk_uint32 *pCfgId);
-
-/* Function Name:
- *      rtk_switch_maxPktLenCfg_set
- * Description:
- *      Set Max packet length configuration
- * Input:
- *      cfgId   - Configuration ID
- *      pktLen  - Max packet length
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-extern rtk_api_ret_t rtk_switch_maxPktLenCfg_set(rtk_uint32 cfgId, rtk_uint32 pktLen);
-
-/* Function Name:
- *      rtk_switch_maxPktLenCfg_get
- * Description:
- *      Get Max packet length configuration
- * Input:
- *      cfgId   - Configuration ID
- *      pPktLen - Max packet length
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-extern rtk_api_ret_t rtk_switch_maxPktLenCfg_get(rtk_uint32 cfgId, rtk_uint32 *pPktLen);
-
-/* Function Name:
- *      rtk_switch_greenEthernet_set
- * Description:
- *      Set all Ports Green Ethernet state.
- * Input:
- *      enable - Green Ethernet state.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - OK
- *      RT_ERR_FAILED   - Failed
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_ENABLE   - Invalid enable input.
- * Note:
- *      This API can set all Ports Green Ethernet state.
- *      The configuration is as following:
- *      - DISABLE
- *      - ENABLE
- */
-extern rtk_api_ret_t rtk_switch_greenEthernet_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_switch_greenEthernet_get
- * Description:
- *      Get all Ports Green Ethernet state.
- * Input:
- *      None
- * Output:
- *      pEnable - Green Ethernet state.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API can get Green Ethernet state.
- */
-extern rtk_api_ret_t rtk_switch_greenEthernet_get(rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_switch_maxLogicalPort_get
- * Description:
- *      Get Max logical port ID
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      Max logical port
- * Note:
- *      This API can get max logical port
- */
-extern rtk_port_t rtk_switch_maxLogicalPort_get(void);
-
-/* Function Name:
- *      rtk_switch_maxMeterId_get
- * Description:
- *      Get Max Meter ID
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      0x00                - Not Initialize
- *      Other value         - Max Meter ID
- * Note:
- *
- */
-extern rtk_uint32 rtk_switch_maxMeterId_get(void);
-
-/* Function Name:
- *      rtk_switch_maxLutAddrNumber_get
- * Description:
- *      Get Max LUT Address number
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      0x00                - Not Initialize
- *      Other value         - Max LUT Address number
- * Note:
- *
- */
-extern rtk_uint32 rtk_switch_maxLutAddrNumber_get(void);
-
-/* Function Name:
- *      rtk_switch_isValidTrunkGrpId
- * Description:
- *      Check if trunk group is valid or not
- * Input:
- *      grpId       - Group ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Trunk Group ID is valid
- *      RT_ERR_LA_TRUNK_ID  - Trunk Group ID is not valid
- * Note:
- *
- */
-rtk_uint32 rtk_switch_isValidTrunkGrpId(rtk_uint32 grpId);
-
-#endif
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_types.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_types.h
deleted file mode 100644
index 589ecb7811..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtk_types.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level type enum definition.
- * Feature :
- *
- */
-
-#ifndef _RTL8367C_TYPES_H_
-#define _RTL8367C_TYPES_H_
-
-//#include <stdio.h>
-
-typedef unsigned long long      rtk_uint64;
-typedef long long               rtk_int64;
-typedef unsigned int            rtk_uint32;
-typedef int                     rtk_int32;
-typedef unsigned short          rtk_uint16;
-typedef short                   rtk_int16;
-typedef unsigned char           rtk_uint8;
-typedef char                    rtk_int8;
-
-#define CONST_T     const
-
-#define RTK_TOTAL_NUM_OF_WORD_FOR_1BIT_PORT_LIST    1
-
-#define RTK_MAX_NUM_OF_PORT                         8
-#define RTK_PORT_ID_MAX                             (RTK_MAX_NUM_OF_PORT-1)
-#define RTK_PHY_ID_MAX                              (RTK_MAX_NUM_OF_PORT-4)
-#define RTK_MAX_PORT_MASK                           0xFF
-
-#define RTK_WHOLE_SYSTEM                            0xFF
-
-typedef struct rtk_portmask_s
-{
-    rtk_uint32  bits[RTK_TOTAL_NUM_OF_WORD_FOR_1BIT_PORT_LIST];
-} rtk_portmask_t;
-
-typedef enum rtk_enable_e
-{
-    DISABLED = 0,
-    ENABLED,
-    RTK_ENABLE_END
-} rtk_enable_t;
-
-#ifndef ETHER_ADDR_LEN
-#define ETHER_ADDR_LEN      6
-#endif
-
-/* ethernet address type */
-typedef struct  rtk_mac_s
-{
-    rtk_uint8 octet[ETHER_ADDR_LEN];
-} rtk_mac_t;
-
-typedef rtk_uint32  rtk_pri_t;      /* priority vlaue */
-typedef rtk_uint32  rtk_qid_t;      /* queue id type */
-typedef rtk_uint32  rtk_data_t;
-typedef rtk_uint32  rtk_dscp_t;     /* dscp vlaue */
-typedef rtk_uint32  rtk_fid_t;      /* filter id type */
-typedef rtk_uint32  rtk_vlan_t;     /* vlan id type */
-typedef rtk_uint32  rtk_mac_cnt_t;  /* MAC count type  */
-typedef rtk_uint32  rtk_meter_id_t; /* meter id type  */
-typedef rtk_uint32  rtk_rate_t;     /* rate type  */
-
-typedef enum rtk_port_e
-{
-    UTP_PORT0 = 0,
-    UTP_PORT1,
-    UTP_PORT2,
-    UTP_PORT3,
-    UTP_PORT4,
-    UTP_PORT5,
-    UTP_PORT6,
-    UTP_PORT7,
-
-    EXT_PORT0 = 16,
-    EXT_PORT1,
-    EXT_PORT2,
-
-    UNDEFINE_PORT = 30,
-    RTK_PORT_MAX = 31
-} rtk_port_t;
-
-
-#ifndef _RTL_TYPES_H
-
-#if 0
-typedef unsigned long long      uint64;
-typedef long long               int64;
-typedef unsigned int            uint32;
-typedef int                     int32;
-typedef unsigned short          uint16;
-typedef short                   int16;
-typedef unsigned char           uint8;
-typedef char                    int8;
-#endif
-
-typedef rtk_uint32                  ipaddr_t;
-typedef rtk_uint32                  memaddr;
-
-#ifndef ETHER_ADDR_LEN
-#define ETHER_ADDR_LEN      6
-#endif
-
-typedef struct ether_addr_s {
-    rtk_uint8 octet[ETHER_ADDR_LEN];
-} ether_addr_t;
-
-#ifdef __KERNEL__
-#define rtlglue_printf printk
-#else
-#define rtlglue_printf printf
-#endif
-#define PRINT           rtlglue_printf
-#endif /*_RTL_TYPES_H*/
-
-/* type abstraction */
-#ifdef EMBEDDED_SUPPORT
-
-typedef rtk_int16                   rtk_api_ret_t;
-typedef rtk_int16                   ret_t;
-typedef rtk_uint32                  rtk_u_long;
-
-#else
-
-typedef rtk_int32                   rtk_api_ret_t;
-typedef rtk_int32                   ret_t;
-typedef rtk_uint64                  rtk_u_long_t;
-
-#endif
-
-#ifndef NULL
-#define NULL 0
-#endif
-
-#ifndef TRUE
-#define TRUE 1
-#endif
-
-#ifndef FALSE
-#define FALSE 0
-#endif
-
-#define CONST           const
-#endif /* _RTL8367C_TYPES_H_ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv.h
deleted file mode 100644
index 55cb41b067..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv.h
+++ /dev/null
@@ -1,129 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature :
- *
- */
-
-
-#ifndef _RTL8367C_ASICDRV_H_
-#define _RTL8367C_ASICDRV_H_
-
-#include <rtk_types.h>
-#include <rtk_error.h>
-#include <rtl8367c_reg.h>
-#include <rtl8367c_base.h>
-
-#define RTL8367C_REGBITLENGTH               16
-#define RTL8367C_REGDATAMAX                 0xFFFF
-
-#define RTL8367C_VIDMAX                     0xFFF
-#define RTL8367C_EVIDMAX                    0x1FFF
-#define RTL8367C_CVIDXNO                    32
-#define RTL8367C_CVIDXMAX                   (RTL8367C_CVIDXNO-1)
-
-#define RTL8367C_PRIMAX                     7
-#define RTL8367C_DSCPMAX                    63
-
-#define RTL8367C_PORTNO                     11
-#define RTL8367C_PORTIDMAX                  (RTL8367C_PORTNO-1)
-#define RTL8367C_PMSKMAX                    ((1<<(RTL8367C_PORTNO))-1)
-#define RTL8367C_PORTMASK                   0x7FF
-
-#define RTL8367C_PHYNO                      5
-#define RTL8367C_PHYIDMAX                  (RTL8367C_PHYNO-1)
-
-#define RTL8367C_SVIDXNO                    64
-#define RTL8367C_SVIDXMAX                   (RTL8367C_SVIDXNO-1)
-#define RTL8367C_MSTIMAX                    15
-
-#define RTL8367C_METERNO                    64
-#define RTL8367C_METERMAX                   (RTL8367C_METERNO-1)
-#define RTL8367C_METERBUCKETSIZEMAX         0xFFFF
-
-#define RTL8367C_QUEUENO                    8
-#define RTL8367C_QIDMAX                     (RTL8367C_QUEUENO-1)
-
-#define RTL8367C_PHY_BUSY_CHECK_COUNTER     1000
-
-#define RTL8367C_QOS_GRANULARTY_MAX         0x7FFFF
-#define RTL8367C_QOS_GRANULARTY_LSB_MASK    0xFFFF
-#define RTL8367C_QOS_GRANULARTY_LSB_OFFSET  0
-#define RTL8367C_QOS_GRANULARTY_MSB_MASK    0x70000
-#define RTL8367C_QOS_GRANULARTY_MSB_OFFSET  16
-
-#define RTL8367C_QOS_GRANULARTY_UNIT_KBPS   8
-
-#define RTL8367C_QOS_RATE_INPUT_MAX         (0x1FFFF * 8)
-#define RTL8367C_QOS_RATE_INPUT_MAX_HSG     (0x7FFFF * 8)
-#define RTL8367C_QOS_RATE_INPUT_MIN         8
-#define RTL8367C_QOS_PPS_INPUT_MAX          (0x7FFFF)
-#define RTL8367C_QOS_PPS_INPUT_MIN          1
-
-#define RTL8367C_QUEUE_MASK                 0xFF
-
-#define RTL8367C_EFIDMAX                    0x7
-#define RTL8367C_FIDMAX                     0xF
-
-#define RTL8367C_EAV_SECONDMAX                  0xFFFFFFFF
-#define RTL8367C_EAV_NANOSECONDMAX          0x3B9AC9FF
-
-
-/* the above macro is generated by genDotH */
-#define RTL8367C_VALID_REG_NO               3869
-
-/*=======================================================================
- *  Enum
- *========================================================================*/
-enum RTL8367C_TABLE_ACCESS_OP
-{
-    TB_OP_READ = 0,
-    TB_OP_WRITE
-};
-
-enum RTL8367C_TABLE_ACCESS_TARGET
-{
-    TB_TARGET_ACLRULE = 1,
-    TB_TARGET_ACLACT,
-    TB_TARGET_CVLAN,
-    TB_TARGET_L2,
-    TB_TARGET_IGMP_GROUP
-};
-
-#define RTL8367C_TABLE_ACCESS_REG_DATA(op, target)    ((op << 3) | target)
-
-/*=======================================================================
- *  Structures
- *========================================================================*/
-
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-extern ret_t rtl8367c_setAsicRegBit(rtk_uint32 reg, rtk_uint32 bit, rtk_uint32 value);
-extern ret_t rtl8367c_getAsicRegBit(rtk_uint32 reg, rtk_uint32 bit, rtk_uint32 *pValue);
-
-extern ret_t rtl8367c_setAsicRegBits(rtk_uint32 reg, rtk_uint32 bits, rtk_uint32 value);
-extern ret_t rtl8367c_getAsicRegBits(rtk_uint32 reg, rtk_uint32 bits, rtk_uint32 *pValue);
-
-extern ret_t rtl8367c_setAsicReg(rtk_uint32 reg, rtk_uint32 value);
-extern ret_t rtl8367c_getAsicReg(rtk_uint32 reg, rtk_uint32 *pValue);
-
-#ifdef __cplusplus
-}
-#endif
-
-
-
-#endif /*#ifndef _RTL8367C_ASICDRV_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_acl.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_acl.h
deleted file mode 100644
index 8ae69ac332..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_acl.h
+++ /dev/null
@@ -1,231 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : ACL related function drivers
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_ACL_H_
-#define _RTL8367C_ASICDRV_ACL_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_ACLRULENO                  96
-
-#define RTL8367C_ACLRULEMAX                 (RTL8367C_ACLRULENO-1)
-#define RTL8367C_ACLRULEFIELDNO             8
-#define RTL8367C_ACLTEMPLATENO              5
-#define RTL8367C_ACLTYPEMAX                 (RTL8367C_ACLTEMPLATENO-1)
-
-#define RTL8367C_ACLRULETBLEN               9
-#define RTL8367C_ACLACTTBLEN                4
-#define RTL8367C_ACLRULETBADDR(type, rule)  ((type << 6) | rule)
-#define RTL8367C_ACLRULETBADDR2(type, rule) ((type << 5) | (rule + 64))
-
-#define ACL_ACT_CVLAN_ENABLE_MASK           0x1
-#define ACL_ACT_SVLAN_ENABLE_MASK           0x2
-#define ACL_ACT_PRIORITY_ENABLE_MASK        0x4
-#define ACL_ACT_POLICING_ENABLE_MASK        0x8
-#define ACL_ACT_FWD_ENABLE_MASK             0x10
-#define ACL_ACT_INTGPIO_ENABLE_MASK         0x20
-
-#define RTL8367C_ACLRULETAGBITS             5
-
-#define RTL8367C_ACLRANGENO                 16
-
-#define RTL8367C_ACLRANGEMAX                (RTL8367C_ACLRANGENO-1)
-
-#define RTL8367C_ACL_PORTRANGEMAX           (0xFFFF)
-#define RTL8367C_ACL_ACT_TABLE_LEN          (4)
-
-enum ACLTCAMTYPES
-{
-    CAREBITS= 0,
-    DATABITS
-};
-
-typedef enum aclFwdAct
-{
-    RTL8367C_ACL_FWD_MIRROR = 0,
-    RTL8367C_ACL_FWD_REDIRECT,
-    RTL8367C_ACL_FWD_MIRRORFUNTION,
-    RTL8367C_ACL_FWD_TRAP,
-} rtl8367c_aclFwd_t;
-
-enum ACLFIELDTYPES
-{
-    ACL_UNUSED,
-    ACL_DMAC0,
-    ACL_DMAC1,
-    ACL_DMAC2,
-    ACL_SMAC0,
-    ACL_SMAC1,
-    ACL_SMAC2,
-    ACL_ETHERTYPE,
-    ACL_STAG,
-    ACL_CTAG,
-    ACL_IP4SIP0 = 0x10,
-    ACL_IP4SIP1,
-    ACL_IP4DIP0,
-    ACL_IP4DIP1,
-    ACL_IP6SIP0WITHIPV4 = 0x20,
-    ACL_IP6SIP1WITHIPV4,
-    ACL_IP6DIP0WITHIPV4 = 0x28,
-    ACL_IP6DIP1WITHIPV4,
-    ACL_VIDRANGE = 0x30,
-    ACL_IPRANGE,
-    ACL_PORTRANGE,
-    ACL_FIELD_VALID,
-    ACL_FIELD_SELECT00 = 0x40,
-    ACL_FIELD_SELECT01,
-    ACL_FIELD_SELECT02,
-    ACL_FIELD_SELECT03,
-    ACL_FIELD_SELECT04,
-    ACL_FIELD_SELECT05,
-    ACL_FIELD_SELECT06,
-    ACL_FIELD_SELECT07,
-    ACL_FIELD_SELECT08,
-    ACL_FIELD_SELECT09,
-    ACL_FIELD_SELECT10,
-    ACL_FIELD_SELECT11,
-    ACL_FIELD_SELECT12,
-    ACL_FIELD_SELECT13,
-    ACL_FIELD_SELECT14,
-    ACL_FIELD_SELECT15,
-    ACL_TCPSPORT = 0x80,
-    ACL_TCPDPORT,
-    ACL_TCPFLAG,
-    ACL_UDPSPORT,
-    ACL_UDPDPORT,
-    ACL_ICMPCODETYPE,
-    ACL_IGMPTYPE,
-    ACL_SPORT,
-    ACL_DPORT,
-    ACL_IP4TOSPROTO,
-    ACL_IP4FLAGOFF,
-    ACL_TCNH,
-    ACL_CPUTAG,
-    ACL_L2PAYLOAD,
-    ACL_IP6SIP0,
-    ACL_IP6SIP1,
-    ACL_IP6SIP2,
-    ACL_IP6SIP3,
-    ACL_IP6SIP4,
-    ACL_IP6SIP5,
-    ACL_IP6SIP6,
-    ACL_IP6SIP7,
-    ACL_IP6DIP0,
-    ACL_IP6DIP1,
-    ACL_IP6DIP2,
-    ACL_IP6DIP3,
-    ACL_IP6DIP4,
-    ACL_IP6DIP5,
-    ACL_IP6DIP6,
-    ACL_IP6DIP7,
-    ACL_TYPE_END
-};
-
-struct acl_rule_smi_st{
-    rtk_uint16 rule_info;
-    rtk_uint16 field[RTL8367C_ACLRULEFIELDNO];
-};
-
-struct acl_rule_smi_ext_st{
-    rtk_uint16 rule_info;
-};
-
-typedef struct ACLRULESMI{
-    struct acl_rule_smi_st  care_bits;
-    rtk_uint16      valid:1;
-    struct acl_rule_smi_st  data_bits;
-
-    struct acl_rule_smi_ext_st care_bits_ext;
-    struct acl_rule_smi_ext_st data_bits_ext;
-}rtl8367c_aclrulesmi;
-
-struct acl_rule_st{
-    rtk_uint16 active_portmsk:11;
-    rtk_uint16 type:3;
-    rtk_uint16 tag_exist:5;
-    rtk_uint16 field[RTL8367C_ACLRULEFIELDNO];
-};
-
-typedef struct ACLRULE{
-    struct acl_rule_st  data_bits;
-    rtk_uint16      valid:1;
-    struct acl_rule_st  care_bits;
-}rtl8367c_aclrule;
-
-
-typedef struct rtl8367c_acltemplate_s{
-    rtk_uint8 field[8];
-}rtl8367c_acltemplate_t;
-
-
-typedef struct acl_act_s{
-    rtk_uint16 cvidx_cact:7;
-    rtk_uint16 cact:2;
-    rtk_uint16 svidx_sact:7;
-    rtk_uint16 sact:2;
-
-
-    rtk_uint16 aclmeteridx:7;
-    rtk_uint16 fwdpmask:11;
-    rtk_uint16 fwdact:2;
-
-    rtk_uint16 pridx:7;
-    rtk_uint16 priact:2;
-    rtk_uint16 gpio_pin:4;
-    rtk_uint16 gpio_en:1;
-    rtk_uint16 aclint:1;
-
-    rtk_uint16 cact_ext:2;
-    rtk_uint16 fwdact_ext:1;
-    rtk_uint16 tag_fmt:2;
-}rtl8367c_acl_act_t;
-
-typedef struct acl_rule_union_s
-{
-    rtl8367c_aclrule aclRule;
-    rtl8367c_acl_act_t aclAct;
-    rtk_uint32 aclActCtrl;
-    rtk_uint32 aclNot;
-}rtl8367c_acl_rule_union_t;
-
-
-extern ret_t rtl8367c_setAsicAcl(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicAcl(rtk_uint32 port, rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicAclUnmatchedPermit(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicAclUnmatchedPermit(rtk_uint32 port, rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicAclRule(rtk_uint32 index, rtl8367c_aclrule *pAclRule);
-extern ret_t rtl8367c_getAsicAclRule(rtk_uint32 index, rtl8367c_aclrule *pAclRule);
-extern ret_t rtl8367c_setAsicAclNot(rtk_uint32 index, rtk_uint32 not);
-extern ret_t rtl8367c_getAsicAclNot(rtk_uint32 index, rtk_uint32* pNot);
-extern ret_t rtl8367c_setAsicAclTemplate(rtk_uint32 index, rtl8367c_acltemplate_t* pAclType);
-extern ret_t rtl8367c_getAsicAclTemplate(rtk_uint32 index, rtl8367c_acltemplate_t *pAclType);
-extern ret_t rtl8367c_setAsicAclAct(rtk_uint32 index, rtl8367c_acl_act_t* pAclAct);
-extern ret_t rtl8367c_getAsicAclAct(rtk_uint32 index, rtl8367c_acl_act_t *pAclAct);
-extern ret_t rtl8367c_setAsicAclActCtrl(rtk_uint32 index, rtk_uint32 aclActCtrl);
-extern ret_t rtl8367c_getAsicAclActCtrl(rtk_uint32 index, rtk_uint32 *aclActCtrl);
-extern ret_t rtl8367c_setAsicAclPortRange(rtk_uint32 index, rtk_uint32 type, rtk_uint32 upperPort, rtk_uint32 lowerPort);
-extern ret_t rtl8367c_getAsicAclPortRange(rtk_uint32 index, rtk_uint32* pType, rtk_uint32* pUpperPort, rtk_uint32* pLowerPort);
-extern ret_t rtl8367c_setAsicAclVidRange(rtk_uint32 index, rtk_uint32 type, rtk_uint32 upperVid, rtk_uint32 lowerVid);
-extern ret_t rtl8367c_getAsicAclVidRange(rtk_uint32 index, rtk_uint32* pType, rtk_uint32* pUpperVid, rtk_uint32* pLowerVid);
-extern ret_t rtl8367c_setAsicAclIpRange(rtk_uint32 index, rtk_uint32 type, ipaddr_t upperIp, ipaddr_t lowerIp);
-extern ret_t rtl8367c_getAsicAclIpRange(rtk_uint32 index, rtk_uint32* pType, ipaddr_t* pUpperIp, ipaddr_t* pLowerIp);
-extern ret_t rtl8367c_setAsicAclGpioPolarity(rtk_uint32 polarity);
-extern ret_t rtl8367c_getAsicAclGpioPolarity(rtk_uint32* pPolarity);
-
-#endif /*_RTL8367C_ASICDRV_ACL_H_*/
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_cputag.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_cputag.h
deleted file mode 100644
index f7a460145e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_cputag.h
+++ /dev/null
@@ -1,49 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Proprietary CPU-tag related function drivers
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_CPUTAG_H_
-#define _RTL8367C_ASICDRV_CPUTAG_H_
-
-#include <rtl8367c_asicdrv.h>
-
-enum CPUTAG_INSERT_MODE
-{
-    CPUTAG_INSERT_TO_ALL = 0,
-    CPUTAG_INSERT_TO_TRAPPING,
-    CPUTAG_INSERT_TO_NO,
-    CPUTAG_INSERT_END
-};
-
-extern ret_t rtl8367c_setAsicCputagEnable(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicCputagEnable(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicCputagTrapPort(rtk_uint32 port);
-extern ret_t rtl8367c_getAsicCputagTrapPort(rtk_uint32 *pPort);
-extern ret_t rtl8367c_setAsicCputagPortmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicCputagPortmask(rtk_uint32 *pPmsk);
-extern ret_t rtl8367c_setAsicCputagInsertMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicCputagInsertMode(rtk_uint32 *pMode);
-extern ret_t rtl8367c_setAsicCputagPriorityRemapping(rtk_uint32 srcPri, rtk_uint32 newPri);
-extern ret_t rtl8367c_getAsicCputagPriorityRemapping(rtk_uint32 srcPri, rtk_uint32 *pNewPri);
-extern ret_t rtl8367c_setAsicCputagPosition(rtk_uint32 postion);
-extern ret_t rtl8367c_getAsicCputagPosition(rtk_uint32* pPostion);
-extern ret_t rtl8367c_setAsicCputagMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicCputagMode(rtk_uint32 *pMode);
-extern ret_t rtl8367c_setAsicCputagRxMinLength(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicCputagRxMinLength(rtk_uint32 *pMode);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_CPUTAG_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_dot1x.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_dot1x.h
deleted file mode 100644
index 7639ae782b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_dot1x.h
+++ /dev/null
@@ -1,52 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : 802.1X related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_DOT1X_H_
-#define _RTL8367C_ASICDRV_DOT1X_H_
-
-#include <rtl8367c_asicdrv.h>
-
-enum DOT1X_UNAUTH_BEHAV
-{
-    DOT1X_UNAUTH_DROP = 0,
-    DOT1X_UNAUTH_TRAP,
-    DOT1X_UNAUTH_GVLAN,
-    DOT1X_UNAUTH_END
-};
-
-extern ret_t rtl8367c_setAsic1xPBEnConfig(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsic1xPBEnConfig(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsic1xPBAuthConfig(rtk_uint32 port, rtk_uint32 auth);
-extern ret_t rtl8367c_getAsic1xPBAuthConfig(rtk_uint32 port, rtk_uint32 *pAuth);
-extern ret_t rtl8367c_setAsic1xPBOpdirConfig(rtk_uint32 port, rtk_uint32 opdir);
-extern ret_t rtl8367c_getAsic1xPBOpdirConfig(rtk_uint32 port, rtk_uint32 *pOpdir);
-extern ret_t rtl8367c_setAsic1xMBEnConfig(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsic1xMBEnConfig(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsic1xMBOpdirConfig(rtk_uint32 opdir);
-extern ret_t rtl8367c_getAsic1xMBOpdirConfig(rtk_uint32 *pOpdir);
-extern ret_t rtl8367c_setAsic1xProcConfig(rtk_uint32 port, rtk_uint32 proc);
-extern ret_t rtl8367c_getAsic1xProcConfig(rtk_uint32 port, rtk_uint32 *pProc);
-extern ret_t rtl8367c_setAsic1xGuestVidx(rtk_uint32 index);
-extern ret_t rtl8367c_getAsic1xGuestVidx(rtk_uint32 *pIndex);
-extern ret_t rtl8367c_setAsic1xGVOpdir(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsic1xGVOpdir(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsic1xTrapPriority(rtk_uint32 priority);
-extern ret_t rtl8367c_getAsic1xTrapPriority(rtk_uint32 *pPriority);
-
-
-#endif /*_RTL8367C_ASICDRV_DOT1X_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_eav.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_eav.h
deleted file mode 100644
index b633f66fb0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_eav.h
+++ /dev/null
@@ -1,109 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Ethernet AV related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_EAV_H_
-#define _RTL8367C_ASICDRV_EAV_H_
-
-#include <rtl8367c_asicdrv.h>
-
-typedef enum RTL8367C_PTP_TIME_CMD_E
-{
-    PTP_TIME_READ = 0,
-    PTP_TIME_WRITE,
-    PTP_TIME_INC,
-    PTP_TIME_DEC,
-    PTP_TIME_CMD_END
-}RTL8367C_PTP_TIME_CMD;
-
-typedef enum RTL8367C_PTP_TIME_ADJ_E
-{
-    PTP_TIME_ADJ_INC = 0,
-    PTP_TIME_ADJ_DEC,
-    PTP_TIME_ADJ_END
-}RTL8367C_PTP_TIME_ADJ;
-
-typedef enum RTL8367C_PTP_TIME_CTRL_E
-{
-    PTP_TIME_CTRL_STOP = 0,
-    PTP_TIME_CTRL_START,
-    PTP_TIME_CTRL_END
-}RTL8367C_PTP_TIME_CTRL;
-
-typedef enum RTL8367C_PTP_INTR_IMRS_E
-{
-    PTP_IMRS_TX_SYNC,
-    PTP_IMRS_TX_DELAY_REQ,
-    PTP_IMRS_TX_PDELAY_REQ,
-    PTP_IMRS_TX_PDELAY_RESP,
-    PTP_IMRS_RX_SYNC,
-    PTP_IMRS_RX_DELAY_REQ,
-    PTP_IMRS_RX_PDELAY_REQ,
-    PTP_IMRS_RX_PDELAY_RESP,
-    PTP_IMRS_END,
-}RTL8367C_PTP_INTR_IMRS;
-
-
-typedef enum RTL8367C_PTP_PKT_TYPE_E
-{
-    PTP_PKT_TYPE_TX_SYNC,
-    PTP_PKT_TYPE_TX_DELAY_REQ,
-    PTP_PKT_TYPE_TX_PDELAY_REQ,
-    PTP_PKT_TYPE_TX_PDELAY_RESP,
-    PTP_PKT_TYPE_RX_SYNC,
-    PTP_PKT_TYPE_RX_DELAY_REQ,
-    PTP_PKT_TYPE_RX_PDELAY_REQ,
-    PTP_PKT_TYPE_RX_PDELAY_RESP,
-    PTP_PKT_TYPE_END,
-}RTL8367C_PTP_PKT_TYPE;
-
-typedef struct  rtl8367c_ptp_time_stamp_s{
-    rtk_uint32 sequence_id;
-    rtk_uint32 second;
-    rtk_uint32 nano_second;
-}rtl8367c_ptp_time_stamp_t;
-
-#define RTL8367C_PTP_INTR_MASK        0xFF
-
-#define RTL8367C_PTP_PORT_MASK        0x3FF
-
-extern ret_t rtl8367c_setAsicEavMacAddress(ether_addr_t mac);
-extern ret_t rtl8367c_getAsicEavMacAddress(ether_addr_t *pMac);
-extern ret_t rtl8367c_setAsicEavTpid(rtk_uint32 outerTag, rtk_uint32 innerTag);
-extern ret_t rtl8367c_getAsicEavTpid(rtk_uint32* pOuterTag, rtk_uint32* pInnerTag);
-extern ret_t rtl8367c_setAsicEavSysTime(rtk_uint32 second, rtk_uint32 nanoSecond);
-extern ret_t rtl8367c_getAsicEavSysTime(rtk_uint32* pSecond, rtk_uint32* pNanoSecond);
-extern ret_t rtl8367c_setAsicEavSysTimeAdjust(rtk_uint32 type, rtk_uint32 second, rtk_uint32 nanoSecond);
-extern ret_t rtl8367c_setAsicEavSysTimeCtrl(rtk_uint32 control);
-extern ret_t rtl8367c_getAsicEavSysTimeCtrl(rtk_uint32* pControl);
-extern ret_t rtl8367c_setAsicEavInterruptMask(rtk_uint32 imr);
-extern ret_t rtl8367c_getAsicEavInterruptMask(rtk_uint32* pImr);
-extern ret_t rtl8367c_getAsicEavInterruptStatus(rtk_uint32* pIms);
-extern ret_t rtl8367c_setAsicEavPortInterruptStatus(rtk_uint32 port, rtk_uint32 ims);
-extern ret_t rtl8367c_getAsicEavPortInterruptStatus(rtk_uint32 port, rtk_uint32* pIms);
-extern ret_t rtl8367c_setAsicEavPortEnable(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicEavPortEnable(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_getAsicEavPortTimeStamp(rtk_uint32 port, rtk_uint32 type, rtl8367c_ptp_time_stamp_t* timeStamp);
-
-extern ret_t rtl8367c_setAsicEavTrap(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicEavTrap(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicEavEnable(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicEavEnable(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicEavPriRemapping(rtk_uint32 srcpriority, rtk_uint32 priority);
-extern ret_t rtl8367c_getAsicEavPriRemapping(rtk_uint32 srcpriority, rtk_uint32 *pPriority);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_EAV_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_eee.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_eee.h
deleted file mode 100644
index 6bedce62b0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_eee.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 48989 $
- * $Date: 2014-07-01 15:45:24 +0800 (¶g¤G, 01 ¤C¤ë 2014) $
- *
- * Purpose : RTL8370 switch high-level API for RTL8367C
- * Feature :
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_EEE_H_
-#define _RTL8367C_ASICDRV_EEE_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define EEE_OCP_PHY_ADDR    (0xA5D0)
-
-extern ret_t rtl8367c_setAsicEee100M(rtk_uint32 port, rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicEee100M(rtk_uint32 port, rtk_uint32 *enable);
-extern ret_t rtl8367c_setAsicEeeGiga(rtk_uint32 port, rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicEeeGiga(rtk_uint32 port, rtk_uint32 *enable);
-
-
-#endif /*_RTL8367C_ASICDRV_EEE_H_*/
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_fc.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_fc.h
deleted file mode 100644
index ce67cdebac..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_fc.h
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Flow control related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_FC_H_
-#define _RTL8367C_ASICDRV_FC_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_PAGE_NUMBER    0x600
-
-
-enum FLOW_CONTROL_TYPE
-{
-    FC_EGRESS = 0,
-    FC_INGRESS,
-};
-
-enum FC_JUMBO_SIZE
-{
-    FC_JUMBO_SIZE_3K = 0,
-    FC_JUMBO_SIZE_4K,
-    FC_JUMBO_SIZE_6K,
-    FC_JUMBO_SIZE_9K,
-    FC_JUMBO_SIZE_END,
-
-};
-
-
-extern ret_t rtl8367c_setAsicFlowControlSelect(rtk_uint32 select);
-extern ret_t rtl8367c_getAsicFlowControlSelect(rtk_uint32 *pSelect);
-extern ret_t rtl8367c_setAsicFlowControlJumboMode(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicFlowControlJumboMode(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicFlowControlJumboModeSize(rtk_uint32 size);
-extern ret_t rtl8367c_getAsicFlowControlJumboModeSize(rtk_uint32* pSize);
-extern ret_t rtl8367c_setAsicFlowControlQueueEgressEnable(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicFlowControlQueueEgressEnable(rtk_uint32 port, rtk_uint32 qid, rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicFlowControlDropAll(rtk_uint32 dropall);
-extern ret_t rtl8367c_getAsicFlowControlDropAll(rtk_uint32* pDropall);
-extern ret_t rtl8367c_setAsicFlowControlPauseAllThreshold(rtk_uint32 threshold);
-extern ret_t rtl8367c_getAsicFlowControlPauseAllThreshold(rtk_uint32 *pThreshold);
-extern ret_t rtl8367c_setAsicFlowControlSystemThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlSystemThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlSharedThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlSharedThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlPortThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlPortThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlPortPrivateThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlPortPrivateThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlSystemDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlSystemDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlSharedDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlSharedDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlPortDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlPortDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlPortPrivateDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlPortPrivateDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlSystemJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlSystemJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlSharedJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlSharedJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlPortJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlPortJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-extern ret_t rtl8367c_setAsicFlowControlPortPrivateJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold);
-extern ret_t rtl8367c_getAsicFlowControlPortPrivateJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold);
-
-extern ret_t rtl8367c_setAsicEgressFlowControlPortDropGap(rtk_uint32 gap);
-extern ret_t rtl8367c_getAsicEgressFlowControlPortDropGap(rtk_uint32 *pGap);
-extern ret_t rtl8367c_setAsicEgressFlowControlQueueDropGap(rtk_uint32 gap);
-extern ret_t rtl8367c_getAsicEgressFlowControlQueueDropGap(rtk_uint32 *pGap);
-extern ret_t rtl8367c_setAsicEgressFlowControlPortDropThreshold(rtk_uint32 port, rtk_uint32 threshold);
-extern ret_t rtl8367c_getAsicEgressFlowControlPortDropThreshold(rtk_uint32 port, rtk_uint32 *pThreshold);
-extern ret_t rtl8367c_setAsicEgressFlowControlQueueDropThreshold(rtk_uint32 qid, rtk_uint32 threshold);
-extern ret_t rtl8367c_getAsicEgressFlowControlQueueDropThreshold(rtk_uint32 qid, rtk_uint32 *pThreshold);
-extern ret_t rtl8367c_getAsicEgressQueueEmptyPortMask(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_getAsicTotalPage(rtk_uint32 *pPageCount);
-extern ret_t rtl8367c_getAsicPulbicPage(rtk_uint32 *pPageCount);
-extern ret_t rtl8367c_getAsicMaxTotalPage(rtk_uint32 *pPageCount);
-extern ret_t rtl8367c_getAsicMaxPulbicPage(rtk_uint32 *pPageCount);
-extern ret_t rtl8367c_getAsicPortPage(rtk_uint32 port, rtk_uint32 *pPageCount);
-extern ret_t rtl8367c_getAsicPortPageMax(rtk_uint32 port, rtk_uint32 *pPageCount);
-extern ret_t rtl8367c_setAsicFlowControlEgressPortIndep(rtk_uint32 port, rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicFlowControlEgressPortIndep(rtk_uint32 port, rtk_uint32 *pEnable);
-
-#endif /*_RTL8367C_ASICDRV_FC_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_green.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_green.h
deleted file mode 100644
index 38fd085d06..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_green.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Green ethernet related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_GREEN_H_
-#define _RTL8367C_ASICDRV_GREEN_H_
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_phy.h>
-
-#define PHY_POWERSAVING_REG                         24
-
-extern ret_t rtl8367c_setAsicGreenTrafficType(rtk_uint32 priority, rtk_uint32 traffictype);
-extern ret_t rtl8367c_getAsicGreenTrafficType(rtk_uint32 priority, rtk_uint32* pTraffictype);
-extern ret_t rtl8367c_getAsicGreenPortPage(rtk_uint32 port, rtk_uint32* pPage);
-extern ret_t rtl8367c_getAsicGreenHighPriorityTraffic(rtk_uint32 port, rtk_uint32* pIndicator);
-extern ret_t rtl8367c_setAsicGreenHighPriorityTraffic(rtk_uint32 port);
-extern ret_t rtl8367c_setAsicGreenEthernet(rtk_uint32 port, rtk_uint32 green);
-extern ret_t rtl8367c_getAsicGreenEthernet(rtk_uint32 port, rtk_uint32* green);
-extern ret_t rtl8367c_setAsicPowerSaving(rtk_uint32 phy, rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicPowerSaving(rtk_uint32 phy, rtk_uint32* enable);
-#endif /*#ifndef _RTL8367C_ASICDRV_GREEN_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_hsb.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_hsb.h
deleted file mode 100644
index f4f9bb377b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_hsb.h
+++ /dev/null
@@ -1,43 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Field selector related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV__HSB_H_
-#define _RTL8367C_ASICDRV__HSB_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_FIELDSEL_FORMAT_NUMBER      (16)
-#define RTL8367C_FIELDSEL_MAX_OFFSET         (255)
-
-enum FIELDSEL_FORMAT_FORMAT
-{
-    FIELDSEL_FORMAT_DEFAULT = 0,
-    FIELDSEL_FORMAT_RAW,
-    FIELDSEL_FORMAT_LLC,
-    FIELDSEL_FORMAT_IPV4,
-    FIELDSEL_FORMAT_ARP,
-    FIELDSEL_FORMAT_IPV6,
-    FIELDSEL_FORMAT_IPPAYLOAD,
-    FIELDSEL_FORMAT_L4PAYLOAD,
-    FIELDSEL_FORMAT_END
-};
-
-extern ret_t rtl8367c_setAsicFieldSelector(rtk_uint32 index, rtk_uint32 format, rtk_uint32 offset);
-extern ret_t rtl8367c_getAsicFieldSelector(rtk_uint32 index, rtk_uint32* pFormat, rtk_uint32* pOffset);
-
-#endif /*_RTL8367C_ASICDRV__HSB_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_i2c.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_i2c.h
deleted file mode 100644
index d5b095a0e5..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_i2c.h
+++ /dev/null
@@ -1,47 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 38651 $
- * $Date: 2016-02-27 14:32:56 +0800 (©P¤T, 17 ¥|¤ë 2016) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : I2C related functions
- *
- */
-
-
-#ifndef _RTL8367C_ASICDRV_I2C_H_
-#define _RTL8367C_ASICDRV_I2C_H_
-#include <rtk_types.h>
-#include <rtl8367c_asicdrv.h>
-
-
-#define TIMEROUT_FOR_MICROSEMI (0x400)
-
-#define GPIO_INPUT 1
-#define GPIO_OUTPUT 2
-
-extern ret_t rtl8367c_setAsicI2C_checkBusIdle(void);
-extern ret_t rtl8367c_setAsicI2CStartCmd(void);
-extern ret_t rtl8367c_setAsicI2CStopCmd(void);
-extern ret_t rtl8367c_setAsicI2CTxOneCharCmd(rtk_uint8 oneChar);
-extern ret_t rtl8367c_setAsicI2CcheckRxAck(void);
-extern ret_t rtl8367c_setAsicI2CRxOneCharCmd(rtk_uint8 *pValue);
-extern ret_t rtl8367c_setAsicI2CTxAckCmd(void);
-extern ret_t rtl8367c_setAsicI2CTxNoAckCmd(void);
-extern ret_t rtl8367c_setAsicI2CSoftRSTseqCmd(void);
-extern ret_t rtl8367c_setAsicI2CGpioPinGroup(rtk_uint32 pinGroup_ID);
-extern ret_t rtl8367c_getAsicI2CGpioPinGroup(rtk_uint32 * pPinGroup_ID);
-
-
-
-
-
-#endif /*#ifndef _RTL8367C_ASICDRV_I2C_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_igmp.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_igmp.h
deleted file mode 100644
index b879b6b520..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_igmp.h
+++ /dev/null
@@ -1,169 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : IGMP related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_IGMP_H_
-#define _RTL8367C_ASICDRV_IGMP_H_
-
-/****************************************************************/
-/* Header File inclusion                                        */
-/****************************************************************/
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_MAX_LEAVE_TIMER        (7)
-#define RTL8367C_MAX_QUERY_INT          (0xFFFF)
-#define RTL8367C_MAX_ROB_VAR            (7)
-
-#define RTL8367C_IGMP_GOUP_NO           (256)
-#define RTL8367C_IGMP_MAX_GOUP          (0xFF)
-#define RTL8367C_IGMP_GRP_BLEN          (3)
-#define RTL8367C_ROUTER_PORT_INVALID    (0xF)
-
-enum RTL8367C_IGMPTABLE_FULL_OP
-{
-    TABLE_FULL_FORWARD = 0,
-    TABLE_FULL_DROP,
-    TABLE_FULL_TRAP,
-    TABLE_FULL_OP_END
-};
-
-enum RTL8367C_CRC_ERR_OP
-{
-    CRC_ERR_DROP = 0,
-    CRC_ERR_TRAP,
-    CRC_ERR_FORWARD,
-    CRC_ERR_OP_END
-};
-
-enum RTL8367C_IGMP_MLD_PROTOCOL_OP
-{
-    PROTOCOL_OP_ASIC = 0,
-    PROTOCOL_OP_FLOOD,
-    PROTOCOL_OP_TRAP,
-    PROTOCOL_OP_DROP,
-    PROTOCOL_OP_END
-};
-
-enum RTL8367C_IGMP_MLD_BYPASS_GROUP
-{
-    BYPASS_224_0_0_X = 0,
-    BYPASS_224_0_1_X,
-    BYPASS_239_255_255_X,
-    BYPASS_IPV6_00XX,
-    BYPASS_GROUP_END
-};
-
-typedef struct
-{
-    rtk_uint32 p0_timer;
-    rtk_uint32 p1_timer;
-    rtk_uint32 p2_timer;
-    rtk_uint32 p3_timer;
-    rtk_uint32 p4_timer;
-    rtk_uint32 p5_timer;
-    rtk_uint32 p6_timer;
-    rtk_uint32 p7_timer;
-    rtk_uint32 p8_timer;
-    rtk_uint32 p9_timer;
-    rtk_uint32 p10_timer;
-    rtk_uint32 report_supp_flag;
-
-}rtl8367c_igmpgroup;
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * This program is the proprietary software of Realtek Semiconductor
- * Corporation and/or its licensors, and only be used, duplicated,
- * modified or distributed under the authorized license from Realtek.
- *
- * ANY USE OF THE SOFTWARE OTHER THAN AS AUTHORIZED UNDER
- * THIS LICENSE OR COPYRIGHT LAW IS PROHIBITED.
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : IGMP related functions
- *
- */
-#include <rtl8367c_asicdrv_igmp.h>
-
-ret_t rtl8367c_setAsicIgmp(rtk_uint32 enabled);
-ret_t rtl8367c_getAsicIgmp(rtk_uint32 *pEnabled);
-ret_t rtl8367c_setAsicIpMulticastVlanLeaky(rtk_uint32 port, rtk_uint32 enabled );
-ret_t rtl8367c_getAsicIpMulticastVlanLeaky(rtk_uint32 port, rtk_uint32 *pEnabled );
-ret_t rtl8367c_setAsicIGMPTableFullOP(rtk_uint32 operation);
-ret_t rtl8367c_getAsicIGMPTableFullOP(rtk_uint32 *pOperation);
-ret_t rtl8367c_setAsicIGMPCRCErrOP(rtk_uint32 operation);
-ret_t rtl8367c_getAsicIGMPCRCErrOP(rtk_uint32 *pOperation);
-ret_t rtl8367c_setAsicIGMPFastLeaveEn(rtk_uint32 enabled);
-ret_t rtl8367c_getAsicIGMPFastLeaveEn(rtk_uint32 *pEnabled);
-ret_t rtl8367c_setAsicIGMPLeaveTimer(rtk_uint32 leave_timer);
-ret_t rtl8367c_getAsicIGMPLeaveTimer(rtk_uint32 *pLeave_timer);
-ret_t rtl8367c_setAsicIGMPQueryInterval(rtk_uint32 interval);
-ret_t rtl8367c_getAsicIGMPQueryInterval(rtk_uint32 *pInterval);
-ret_t rtl8367c_setAsicIGMPRobVar(rtk_uint32 rob_var);
-ret_t rtl8367c_getAsicIGMPRobVar(rtk_uint32 *pRob_var);
-ret_t rtl8367c_setAsicIGMPStaticRouterPort(rtk_uint32 pmsk);
-ret_t rtl8367c_getAsicIGMPStaticRouterPort(rtk_uint32 *pMsk);
-ret_t rtl8367c_setAsicIGMPAllowDynamicRouterPort(rtk_uint32 pmsk);
-ret_t rtl8367c_getAsicIGMPAllowDynamicRouterPort(rtk_uint32 *pPmsk);
-ret_t rtl8367c_getAsicIGMPdynamicRouterPort1(rtk_uint32 *pPort, rtk_uint32 *pTimer);
-ret_t rtl8367c_getAsicIGMPdynamicRouterPort2(rtk_uint32 *pPort, rtk_uint32 *pTimer);
-ret_t rtl8367c_setAsicIGMPSuppression(rtk_uint32 report_supp_enabled, rtk_uint32 leave_supp_enabled);
-ret_t rtl8367c_getAsicIGMPSuppression(rtk_uint32 *pReport_supp_enabled, rtk_uint32 *pLeave_supp_enabled);
-ret_t rtl8367c_setAsicIGMPQueryRX(rtk_uint32 port, rtk_uint32 allow_query);
-ret_t rtl8367c_getAsicIGMPQueryRX(rtk_uint32 port, rtk_uint32 *pAllow_query);
-ret_t rtl8367c_setAsicIGMPReportRX(rtk_uint32 port, rtk_uint32 allow_report);
-ret_t rtl8367c_getAsicIGMPReportRX(rtk_uint32 port, rtk_uint32 *pAllow_report);
-ret_t rtl8367c_setAsicIGMPLeaveRX(rtk_uint32 port, rtk_uint32 allow_leave);
-ret_t rtl8367c_getAsicIGMPLeaveRX(rtk_uint32 port, rtk_uint32 *pAllow_leave);
-ret_t rtl8367c_setAsicIGMPMRPRX(rtk_uint32 port, rtk_uint32 allow_mrp);
-ret_t rtl8367c_getAsicIGMPMRPRX(rtk_uint32 port, rtk_uint32 *pAllow_mrp);
-ret_t rtl8367c_setAsicIGMPMcDataRX(rtk_uint32 port, rtk_uint32 allow_mcdata);
-ret_t rtl8367c_getAsicIGMPMcDataRX(rtk_uint32 port, rtk_uint32 *pAllow_mcdata);
-ret_t rtl8367c_setAsicIGMPv1Opeartion(rtk_uint32 port, rtk_uint32 igmpv1_op);
-ret_t rtl8367c_getAsicIGMPv1Opeartion(rtk_uint32 port, rtk_uint32 *pIgmpv1_op);
-ret_t rtl8367c_setAsicIGMPv2Opeartion(rtk_uint32 port, rtk_uint32 igmpv2_op);
-ret_t rtl8367c_getAsicIGMPv2Opeartion(rtk_uint32 port, rtk_uint32 *pIgmpv2_op);
-ret_t rtl8367c_setAsicIGMPv3Opeartion(rtk_uint32 port, rtk_uint32 igmpv3_op);
-ret_t rtl8367c_getAsicIGMPv3Opeartion(rtk_uint32 port, rtk_uint32 *pIgmpv3_op);
-ret_t rtl8367c_setAsicMLDv1Opeartion(rtk_uint32 port, rtk_uint32 mldv1_op);
-ret_t rtl8367c_getAsicMLDv1Opeartion(rtk_uint32 port, rtk_uint32 *pMldv1_op);
-ret_t rtl8367c_setAsicMLDv2Opeartion(rtk_uint32 port, rtk_uint32 mldv2_op);
-ret_t rtl8367c_getAsicMLDv2Opeartion(rtk_uint32 port, rtk_uint32 *pMldv2_op);
-ret_t rtl8367c_setAsicIGMPPortMAXGroup(rtk_uint32 port, rtk_uint32 max_group);
-ret_t rtl8367c_getAsicIGMPPortMAXGroup(rtk_uint32 port, rtk_uint32 *pMax_group);
-ret_t rtl8367c_getAsicIGMPPortCurrentGroup(rtk_uint32 port, rtk_uint32 *pCurrent_group);
-ret_t rtl8367c_getAsicIGMPGroup(rtk_uint32 idx, rtk_uint32 *pValid, rtl8367c_igmpgroup *pGrp);
-ret_t rtl8367c_setAsicIpMulticastPortIsoLeaky(rtk_uint32 port, rtk_uint32 enabled);
-ret_t rtl8367c_getAsicIpMulticastPortIsoLeaky(rtk_uint32 port, rtk_uint32 *pEnabled);
-ret_t rtl8367c_setAsicIGMPReportLeaveFlood(rtk_uint32 flood);
-ret_t rtl8367c_getAsicIGMPReportLeaveFlood(rtk_uint32 *pFlood);
-ret_t rtl8367c_setAsicIGMPDropLeaveZero(rtk_uint32 drop);
-ret_t rtl8367c_getAsicIGMPDropLeaveZero(rtk_uint32 *pDrop);
-ret_t rtl8367c_setAsicIGMPBypassStormCTRL(rtk_uint32 bypass);
-ret_t rtl8367c_getAsicIGMPBypassStormCTRL(rtk_uint32 *pBypass);
-ret_t rtl8367c_setAsicIGMPIsoLeaky(rtk_uint32 leaky);
-ret_t rtl8367c_getAsicIGMPIsoLeaky(rtk_uint32 *pLeaky);
-ret_t rtl8367c_setAsicIGMPVLANLeaky(rtk_uint32 leaky);
-ret_t rtl8367c_getAsicIGMPVLANLeaky(rtk_uint32 *pLeaky);
-ret_t rtl8367c_setAsicIGMPBypassGroup(rtk_uint32 bypassType, rtk_uint32 enabled);
-ret_t rtl8367c_getAsicIGMPBypassGroup(rtk_uint32 bypassType, rtk_uint32 *pEnabled);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_IGMP_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_inbwctrl.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_inbwctrl.h
deleted file mode 100644
index 10f3545322..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_inbwctrl.h
+++ /dev/null
@@ -1,30 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Ingress bandwidth control related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_INBWCTRL_H_
-#define _RTL8367C_ASICDRV_INBWCTRL_H_
-
-#include <rtl8367c_asicdrv.h>
-
-extern ret_t rtl8367c_setAsicPortIngressBandwidth(rtk_uint32 port, rtk_uint32 bandwidth, rtk_uint32 preifg, rtk_uint32 enableFC);
-extern ret_t rtl8367c_getAsicPortIngressBandwidth(rtk_uint32 port, rtk_uint32* pBandwidth, rtk_uint32* pPreifg, rtk_uint32* pEnableFC );
-extern ret_t rtl8367c_setAsicPortIngressBandwidthBypass(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortIngressBandwidthBypass(rtk_uint32* pEnabled);
-
-
-#endif /*_RTL8367C_ASICDRV_INBWCTRL_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_interrupt.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_interrupt.h
deleted file mode 100644
index 8b78014ab0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_interrupt.h
+++ /dev/null
@@ -1,66 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Interrupt related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_INTERRUPT_H_
-#define _RTL8367C_ASICDRV_INTERRUPT_H_
-
-#include <rtl8367c_asicdrv.h>
-
-typedef enum RTL8367C_INTR_IMRS_E
-{
-    IMRS_LINK_CHANGE,
-    IMRS_METER_EXCEED,
-    IMRS_L2_LEARN,
-    IMRS_SPEED_CHANGE,
-    IMRS_SPECIAL_CONGESTION,
-    IMRS_GREEN_FEATURE,
-    IMRS_LOOP_DETECTION,
-    IMRS_8051,
-    IMRS_CABLE_DIAG,
-    IMRS_ACL,
-    IMRS_RESERVED, /* Unused */
-    IMRS_SLIENT,
-    IMRS_END,
-}RTL8367C_INTR_IMRS;
-
-typedef enum RTL8367C_INTR_INDICATOR_E
-{
-    INTRST_L2_LEARN = 0,
-    INTRST_SPEED_CHANGE,
-    INTRST_SPECIAL_CONGESTION,
-    INTRST_PORT_LINKDOWN,
-    INTRST_PORT_LINKUP,
-    INTRST_METER0_15,
-    INTRST_METER16_31,
-    INTRST_RLDP_LOOPED,
-    INTRST_RLDP_RELEASED,
-    INTRST_SYS_LEARN,
-    INTRST_END,
-}RTL8367C_INTR_INDICATOR;
-
-extern ret_t rtl8367c_setAsicInterruptPolarity(rtk_uint32 polarity);
-extern ret_t rtl8367c_getAsicInterruptPolarity(rtk_uint32* pPolarity);
-extern ret_t rtl8367c_setAsicInterruptMask(rtk_uint32 imr);
-extern ret_t rtl8367c_getAsicInterruptMask(rtk_uint32* pImr);
-extern ret_t rtl8367c_setAsicInterruptStatus(rtk_uint32 ims);
-extern ret_t rtl8367c_getAsicInterruptStatus(rtk_uint32* pIms);
-extern ret_t rtl8367c_setAsicInterruptRelatedStatus(rtk_uint32 type, rtk_uint32 status);
-extern ret_t rtl8367c_getAsicInterruptRelatedStatus(rtk_uint32 type, rtk_uint32* pStatus);
-
-
-#endif /*#ifndef _RTL8367C_ASICDRV_INTERRUPT_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_led.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_led.h
deleted file mode 100644
index a7f8e20643..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_led.h
+++ /dev/null
@@ -1,138 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : LED related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_LED_H_
-#define _RTL8367C_ASICDRV_LED_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_LEDGROUPNO                 3
-#define RTL8367C_LEDGROUPMASK               0x7
-#define RTL8367C_LED_FORCE_MODE_BASE        RTL8367C_REG_CPU_FORCE_LED0_CFG0
-#define RTL8367C_LED_FORCE_CTRL             RTL8367C_REG_CPU_FORCE_LED_CFG
-
-enum RTL8367C_LEDOP{
-
-    LEDOP_SCAN0=0,
-    LEDOP_SCAN1,
-    LEDOP_PARALLEL,
-    LEDOP_SERIAL,
-    LEDOP_END,
-};
-
-enum RTL8367C_LEDSERACT{
-
-    LEDSERACT_HIGH=0,
-    LEDSERACT_LOW,
-    LEDSERACT_MAX,
-};
-
-enum RTL8367C_LEDSER{
-
-    LEDSER_16G=0,
-    LEDSER_8G,
-    LEDSER_MAX,
-};
-
-enum RTL8367C_LEDCONF{
-
-    LEDCONF_LEDOFF=0,
-    LEDCONF_DUPCOL,
-    LEDCONF_LINK_ACT,
-    LEDCONF_SPD1000,
-    LEDCONF_SPD100,
-    LEDCONF_SPD10,
-    LEDCONF_SPD1000ACT,
-    LEDCONF_SPD100ACT,
-    LEDCONF_SPD10ACT,
-    LEDCONF_SPD10010ACT,
-    LEDCONF_LOOPDETECT,
-    LEDCONF_EEE,
-    LEDCONF_LINKRX,
-    LEDCONF_LINKTX,
-    LEDCONF_MASTER,
-    LEDCONF_ACT,
-    LEDCONF_END
-};
-
-enum RTL8367C_LEDBLINKRATE{
-
-    LEDBLINKRATE_32MS=0,
-    LEDBLINKRATE_64MS,
-    LEDBLINKRATE_128MS,
-    LEDBLINKRATE_256MS,
-    LEDBLINKRATE_512MS,
-    LEDBLINKRATE_1024MS,
-    LEDBLINKRATE_48MS,
-    LEDBLINKRATE_96MS,
-    LEDBLINKRATE_END,
-};
-
-enum RTL8367C_LEDFORCEMODE{
-
-    LEDFORCEMODE_NORMAL=0,
-    LEDFORCEMODE_BLINK,
-    LEDFORCEMODE_OFF,
-    LEDFORCEMODE_ON,
-    LEDFORCEMODE_END,
-};
-
-enum RTL8367C_LEDFORCERATE{
-
-    LEDFORCERATE_512MS=0,
-    LEDFORCERATE_1024MS,
-    LEDFORCERATE_2048MS,
-    LEDFORCERATE_NORMAL,
-    LEDFORCERATE_END,
-
-};
-
-enum RTL8367C_LEDMODE
-{
-    RTL8367C_LED_MODE_0 = 0,
-    RTL8367C_LED_MODE_1,
-    RTL8367C_LED_MODE_2,
-    RTL8367C_LED_MODE_3,
-    RTL8367C_LED_MODE_END
-};
-
-extern ret_t rtl8367c_setAsicLedIndicateInfoConfig(rtk_uint32 ledno, rtk_uint32 config);
-extern ret_t rtl8367c_getAsicLedIndicateInfoConfig(rtk_uint32 ledno, rtk_uint32* pConfig);
-extern ret_t rtl8367c_setAsicForceLed(rtk_uint32 port, rtk_uint32 group, rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicForceLed(rtk_uint32 port, rtk_uint32 group, rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicForceGroupLed(rtk_uint32 groupmask, rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicForceGroupLed(rtk_uint32* groupmask, rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicLedBlinkRate(rtk_uint32 blinkRate);
-extern ret_t rtl8367c_getAsicLedBlinkRate(rtk_uint32* pBlinkRate);
-extern ret_t rtl8367c_setAsicLedForceBlinkRate(rtk_uint32 blinkRate);
-extern ret_t rtl8367c_getAsicLedForceBlinkRate(rtk_uint32* pBlinkRate);
-extern ret_t rtl8367c_setAsicLedGroupMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicLedGroupMode(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicLedGroupEnable(rtk_uint32 group, rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicLedGroupEnable(rtk_uint32 group, rtk_uint32 *portmask);
-extern ret_t rtl8367c_setAsicLedOperationMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicLedOperationMode(rtk_uint32 *mode);
-extern ret_t rtl8367c_setAsicLedSerialModeConfig(rtk_uint32 active, rtk_uint32 serimode);
-extern ret_t rtl8367c_getAsicLedSerialModeConfig(rtk_uint32 *active, rtk_uint32 *serimode);
-extern ret_t rtl8367c_setAsicLedOutputEnable(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicLedOutputEnable(rtk_uint32 *ptr_enabled);
-extern ret_t rtl8367c_setAsicLedSerialOutput(rtk_uint32 output, rtk_uint32 pmask);
-extern ret_t rtl8367c_getAsicLedSerialOutput(rtk_uint32 *pOutput, rtk_uint32 *pPmask);
-
-
-#endif /*#ifndef _RTL8367C_ASICDRV_LED_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_lut.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_lut.h
deleted file mode 100644
index c94ea07601..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_lut.h
+++ /dev/null
@@ -1,159 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : LUT related functions
- *
- */
-
-
-#ifndef _RTL8367C_ASICDRV_LUT_H_
-#define _RTL8367C_ASICDRV_LUT_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_LUT_AGETIMERMAX        (7)
-#define RTL8367C_LUT_AGESPEEDMAX        (3)
-#define RTL8367C_LUT_LEARNLIMITMAX      (0x1040)
-#define RTL8367C_LUT_ADDRMAX            (0x103F)
-#define RTL8367C_LUT_IPMCGRP_TABLE_MAX  (0x3F)
-#define RTL8367C_LUT_ENTRY_SIZE         (6)
-#define RTL8367C_LUT_BUSY_CHECK_NO      (10)
-
-#define RTL8367C_LUT_TABLE_SIZE         (6)
-
-enum RTL8367C_LUTHASHMETHOD{
-
-    LUTHASHMETHOD_SVL=0,
-    LUTHASHMETHOD_IVL,
-    LUTHASHMETHOD_END,
-};
-
-
-enum RTL8367C_LRNOVERACT{
-
-    LRNOVERACT_FORWARD=0,
-    LRNOVERACT_DROP,
-    LRNOVERACT_TRAP,
-    LRNOVERACT_END,
-};
-
-enum RTL8367C_LUTREADMETHOD{
-
-    LUTREADMETHOD_MAC =0,
-    LUTREADMETHOD_ADDRESS,
-    LUTREADMETHOD_NEXT_ADDRESS,
-    LUTREADMETHOD_NEXT_L2UC,
-    LUTREADMETHOD_NEXT_L2MC,
-    LUTREADMETHOD_NEXT_L3MC,
-    LUTREADMETHOD_NEXT_L2L3MC,
-    LUTREADMETHOD_NEXT_L2UCSPA,
-};
-
-enum RTL8367C_FLUSHMODE
-{
-    FLUSHMDOE_PORT = 0,
-    FLUSHMDOE_VID,
-    FLUSHMDOE_FID,
-    FLUSHMDOE_END,
-};
-
-enum RTL8367C_FLUSHTYPE
-{
-    FLUSHTYPE_DYNAMIC = 0,
-    FLUSHTYPE_BOTH,
-    FLUSHTYPE_END,
-};
-
-
-typedef struct LUTTABLE{
-
-    ipaddr_t sip;
-    ipaddr_t dip;
-    ether_addr_t mac;
-    rtk_uint16 ivl_svl:1;
-    rtk_uint16 cvid_fid:12;
-    rtk_uint16 fid:4;
-    rtk_uint16 efid:3;
-
-    rtk_uint16 nosalearn:1;
-    rtk_uint16 da_block:1;
-    rtk_uint16 sa_block:1;
-    rtk_uint16 auth:1;
-    rtk_uint16 lut_pri:3;
-    rtk_uint16 sa_en:1;
-    rtk_uint16 fwd_en:1;
-    rtk_uint16 mbr:11;
-    rtk_uint16 spa:4;
-    rtk_uint16 age:3;
-    rtk_uint16 l3lookup:1;
-    rtk_uint16 igmp_asic:1;
-    rtk_uint16 igmpidx:8;
-
-    rtk_uint16 lookup_hit:1;
-    rtk_uint16 lookup_busy:1;
-    rtk_uint16 address:13;
-
-    rtk_uint16 l3vidlookup:1;
-    rtk_uint16 l3_vid:12;
-
-    rtk_uint16 wait_time;
-
-}rtl8367c_luttb;
-
-extern ret_t rtl8367c_setAsicLutIpMulticastLookup(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicLutIpMulticastLookup(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicLutIpMulticastVidLookup(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicLutIpMulticastVidLookup(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicLutAgeTimerSpeed(rtk_uint32 timer, rtk_uint32 speed);
-extern ret_t rtl8367c_getAsicLutAgeTimerSpeed(rtk_uint32* pTimer, rtk_uint32* pSpeed);
-extern ret_t rtl8367c_setAsicLutCamTbUsage(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicLutCamTbUsage(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_getAsicLutCamType(rtk_uint32* pType);
-extern ret_t rtl8367c_setAsicLutLearnLimitNo(rtk_uint32 port, rtk_uint32 number);
-extern ret_t rtl8367c_getAsicLutLearnLimitNo(rtk_uint32 port, rtk_uint32* pNumber);
-extern ret_t rtl8367c_setAsicSystemLutLearnLimitNo(rtk_uint32 number);
-extern ret_t rtl8367c_getAsicSystemLutLearnLimitNo(rtk_uint32 *pNumber);
-extern ret_t rtl8367c_setAsicLutLearnOverAct(rtk_uint32 action);
-extern ret_t rtl8367c_getAsicLutLearnOverAct(rtk_uint32* pAction);
-extern ret_t rtl8367c_setAsicSystemLutLearnOverAct(rtk_uint32 action);
-extern ret_t rtl8367c_getAsicSystemLutLearnOverAct(rtk_uint32 *pAction);
-extern ret_t rtl8367c_setAsicSystemLutLearnPortMask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicSystemLutLearnPortMask(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicL2LookupTb(rtl8367c_luttb *pL2Table);
-extern ret_t rtl8367c_getAsicL2LookupTb(rtk_uint32 method, rtl8367c_luttb *pL2Table);
-extern ret_t rtl8367c_getAsicLutLearnNo(rtk_uint32 port, rtk_uint32* pNumber);
-extern ret_t rtl8367c_setAsicLutIpLookupMethod(rtk_uint32 type);
-extern ret_t rtl8367c_getAsicLutIpLookupMethod(rtk_uint32* pType);
-extern ret_t rtl8367c_setAsicLutForceFlush(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicLutForceFlushStatus(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicLutFlushMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicLutFlushMode(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicLutFlushType(rtk_uint32 type);
-extern ret_t rtl8367c_getAsicLutFlushType(rtk_uint32* pType);
-extern ret_t rtl8367c_setAsicLutFlushVid(rtk_uint32 vid);
-extern ret_t rtl8367c_getAsicLutFlushVid(rtk_uint32* pVid);
-extern ret_t rtl8367c_setAsicLutFlushFid(rtk_uint32 fid);
-extern ret_t rtl8367c_getAsicLutFlushFid(rtk_uint32* pFid);
-extern ret_t rtl8367c_setAsicLutDisableAging(rtk_uint32 port, rtk_uint32 disabled);
-extern ret_t rtl8367c_getAsicLutDisableAging(rtk_uint32 port, rtk_uint32 *pDisabled);
-extern ret_t rtl8367c_setAsicLutIPMCGroup(rtk_uint32 index, ipaddr_t group_addr, rtk_uint32 vid, rtk_uint32 pmask, rtk_uint32 valid);
-extern ret_t rtl8367c_getAsicLutIPMCGroup(rtk_uint32 index, ipaddr_t *pGroup_addr, rtk_uint32 *pVid, rtk_uint32 *pPmask, rtk_uint32 *pValid);
-extern ret_t rtl8367c_setAsicLutLinkDownForceAging(rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicLutLinkDownForceAging(rtk_uint32 *pEnable);
-extern ret_t rtl8367c_setAsicLutFlushAll(void);
-extern ret_t rtl8367c_getAsicLutFlushAllStatus(rtk_uint32 *pBusyStatus);
-extern ret_t rtl8367c_setAsicLutIpmcFwdRouterPort(rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicLutIpmcFwdRouterPort(rtk_uint32 *pEnable);
-
-#endif /*_RTL8367C_ASICDRV_LUT_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_meter.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_meter.h
deleted file mode 100644
index ba761a94f8..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_meter.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Shared meter related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_METER_H_
-#define _RTL8367C_ASICDRV_METER_H_
-
-#include <rtl8367c_asicdrv.h>
-
-
-extern ret_t rtl8367c_setAsicShareMeter(rtk_uint32 index, rtk_uint32 rate, rtk_uint32 ifg);
-extern ret_t rtl8367c_getAsicShareMeter(rtk_uint32 index, rtk_uint32 *pRate, rtk_uint32 *pIfg);
-extern ret_t rtl8367c_setAsicShareMeterBucketSize(rtk_uint32 index, rtk_uint32 lbThreshold);
-extern ret_t rtl8367c_getAsicShareMeterBucketSize(rtk_uint32 index, rtk_uint32 *pLbThreshold);
-extern ret_t rtl8367c_setAsicShareMeterType(rtk_uint32 index, rtk_uint32 type);
-extern ret_t rtl8367c_getAsicShareMeterType(rtk_uint32 index, rtk_uint32 *pType);
-extern ret_t rtl8367c_setAsicMeterExceedStatus(rtk_uint32 index);
-extern ret_t rtl8367c_getAsicMeterExceedStatus(rtk_uint32 index, rtk_uint32* pStatus);
-
-#endif /*_RTL8367C_ASICDRV_FC_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_mib.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_mib.h
deleted file mode 100644
index ca46e0f470..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_mib.h
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : MIB related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_MIB_H_
-#define _RTL8367C_ASICDRV_MIB_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_MIB_PORT_OFFSET                (0x7C)
-#define RTL8367C_MIB_LEARNENTRYDISCARD_OFFSET   (0x420)
-
-#define RTL8367C_MAX_LOG_CNT_NUM                (32)
-#define RTL8367C_MIB_MAX_LOG_CNT_IDX            (RTL8367C_MAX_LOG_CNT_NUM - 1)
-#define RTL8367C_MIB_LOG_CNT_OFFSET             (0x3E0)
-#define RTL8367C_MIB_MAX_LOG_MODE_IDX           (16-1)
-
-typedef enum RTL8367C_MIBCOUNTER_E{
-
-    /* RX */
-    ifInOctets = 0,
-
-    dot3StatsFCSErrors,
-    dot3StatsSymbolErrors,
-    dot3InPauseFrames,
-    dot3ControlInUnknownOpcodes,
-
-    etherStatsFragments,
-    etherStatsJabbers,
-    ifInUcastPkts,
-    etherStatsDropEvents,
-
-    ifInMulticastPkts,
-    ifInBroadcastPkts,
-    inMldChecksumError,
-    inIgmpChecksumError,
-    inMldSpecificQuery,
-    inMldGeneralQuery,
-    inIgmpSpecificQuery,
-    inIgmpGeneralQuery,
-    inMldLeaves,
-    inIgmpLeaves,
-
-    /* TX/RX */
-    etherStatsOctets,
-
-    etherStatsUnderSizePkts,
-    etherOversizeStats,
-    etherStatsPkts64Octets,
-    etherStatsPkts65to127Octets,
-    etherStatsPkts128to255Octets,
-    etherStatsPkts256to511Octets,
-    etherStatsPkts512to1023Octets,
-    etherStatsPkts1024to1518Octets,
-
-    /* TX */
-    ifOutOctets,
-
-    dot3StatsSingleCollisionFrames,
-    dot3StatMultipleCollisionFrames,
-    dot3sDeferredTransmissions,
-    dot3StatsLateCollisions,
-    etherStatsCollisions,
-    dot3StatsExcessiveCollisions,
-    dot3OutPauseFrames,
-    ifOutDiscards,
-
-    /* ALE */
-    dot1dTpPortInDiscards,
-    ifOutUcastPkts,
-    ifOutMulticastPkts,
-    ifOutBroadcastPkts,
-    outOampduPkts,
-    inOampduPkts,
-
-    inIgmpJoinsSuccess,
-    inIgmpJoinsFail,
-    inMldJoinsSuccess,
-    inMldJoinsFail,
-    inReportSuppressionDrop,
-    inLeaveSuppressionDrop,
-    outIgmpReports,
-    outIgmpLeaves,
-    outIgmpGeneralQuery,
-    outIgmpSpecificQuery,
-    outMldReports,
-    outMldLeaves,
-    outMldGeneralQuery,
-    outMldSpecificQuery,
-    inKnownMulticastPkts,
-
-    /*Device only */
-    dot1dTpLearnedEntryDiscards,
-    RTL8367C_MIBS_NUMBER,
-
-}RTL8367C_MIBCOUNTER;
-
-
-extern ret_t rtl8367c_setAsicMIBsCounterReset(rtk_uint32 greset, rtk_uint32 qmreset, rtk_uint32 pmask);
-extern ret_t rtl8367c_getAsicMIBsCounter(rtk_uint32 port,RTL8367C_MIBCOUNTER mibIdx, rtk_uint64* pCounter);
-extern ret_t rtl8367c_getAsicMIBsLogCounter(rtk_uint32 index, rtk_uint32 *pCounter);
-extern ret_t rtl8367c_getAsicMIBsControl(rtk_uint32* pMask);
-
-extern ret_t rtl8367c_setAsicMIBsResetValue(rtk_uint32 value);
-extern ret_t rtl8367c_getAsicMIBsResetValue(rtk_uint32* value);
-
-extern ret_t rtl8367c_setAsicMIBsUsageMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicMIBsUsageMode(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicMIBsTimer(rtk_uint32 timer);
-extern ret_t rtl8367c_getAsicMIBsTimer(rtk_uint32* pTimer);
-extern ret_t rtl8367c_setAsicMIBsLoggingMode(rtk_uint32 index, rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicMIBsLoggingMode(rtk_uint32 index, rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicMIBsLoggingType(rtk_uint32 index, rtk_uint32 type);
-extern ret_t rtl8367c_getAsicMIBsLoggingType(rtk_uint32 index, rtk_uint32* pType);
-extern ret_t rtl8367c_setAsicMIBsResetLoggingCounter(rtk_uint32 index);
-extern ret_t rtl8367c_setAsicMIBsLength(rtk_uint32 txLengthMode, rtk_uint32 rxLengthMode);
-extern ret_t rtl8367c_getAsicMIBsLength(rtk_uint32 *pTxLengthMode, rtk_uint32 *pRxLengthMode);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_MIB_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_mirror.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_mirror.h
deleted file mode 100644
index 23b788d7a6..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_mirror.h
+++ /dev/null
@@ -1,49 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port mirror related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_MIRROR_H_
-#define _RTL8367C_ASICDRV_MIRROR_H_
-
-#include <rtl8367c_asicdrv.h>
-
-extern ret_t rtl8367c_setAsicPortMirror(rtk_uint32 source, rtk_uint32 monitor);
-extern ret_t rtl8367c_getAsicPortMirror(rtk_uint32 *pSource, rtk_uint32 *pMonitor);
-extern ret_t rtl8367c_setAsicPortMirrorRxFunction(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortMirrorRxFunction(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicPortMirrorTxFunction(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortMirrorTxFunction(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicPortMirrorIsolation(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortMirrorIsolation(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicPortMirrorPriority(rtk_uint32 priority);
-extern ret_t rtl8367c_getAsicPortMirrorPriority(rtk_uint32* pPriority);
-extern ret_t rtl8367c_setAsicPortMirrorMask(rtk_uint32 SourcePortmask);
-extern ret_t rtl8367c_getAsicPortMirrorMask(rtk_uint32 *pSourcePortmask);
-extern ret_t rtl8367c_setAsicPortMirrorVlanRxLeaky(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortMirrorVlanRxLeaky(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicPortMirrorVlanTxLeaky(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortMirrorVlanTxLeaky(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicPortMirrorIsolationRxLeaky(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortMirrorIsolationRxLeaky(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicPortMirrorIsolationTxLeaky(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortMirrorIsolationTxLeaky(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicPortMirrorRealKeep(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicPortMirrorRealKeep(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicPortMirrorOverride(rtk_uint32 rxMirror, rtk_uint32 txMirror, rtk_uint32 aclMirror);
-extern ret_t rtl8367c_getAsicPortMirrorOverride(rtk_uint32 *pRxMirror, rtk_uint32 *pTxMirror, rtk_uint32 *pAclMirror);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_MIRROR_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_misc.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_misc.h
deleted file mode 100644
index c666a7b58b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_misc.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Miscellaneous functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_MISC_H_
-#define _RTL8367C_ASICDRV_MISC_H_
-
-#include <rtl8367c_asicdrv.h>
-
-extern ret_t rtl8367c_setAsicMacAddress(ether_addr_t mac);
-extern ret_t rtl8367c_getAsicMacAddress(ether_addr_t *pMac);
-extern ret_t rtl8367c_getAsicDebugInfo(rtk_uint32 port, rtk_uint32 *pDebugifo);
-extern ret_t rtl8367c_setAsicPortJamMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicPortJamMode(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicMaxLengthCfg(rtk_uint32 cfgId, rtk_uint32 maxLength);
-extern ret_t rtl8367c_getAsicMaxLengthCfg(rtk_uint32 cfgId, rtk_uint32 *pMaxLength);
-extern ret_t rtl8367c_setAsicMaxLength(rtk_uint32 port, rtk_uint32 type, rtk_uint32 cfgId);
-extern ret_t rtl8367c_getAsicMaxLength(rtk_uint32 port, rtk_uint32 type, rtk_uint32 *pCfgId);
-
-#endif /*_RTL8367C_ASICDRV_MISC_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_oam.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_oam.h
deleted file mode 100644
index c09dc76988..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_oam.h
+++ /dev/null
@@ -1,47 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 42321 $
- * $Date: 2013-08-26 13:51:29 +0800 (¶g¤@, 26 ¤K¤ë 2013) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : OAM related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_OAM_H_
-#define _RTL8367C_ASICDRV_OAM_H_
-
-#include <rtl8367c_asicdrv.h>
-
-enum OAMPARACT
-{
-    OAM_PARFWD = 0,
-    OAM_PARLB,
-    OAM_PARDISCARD,
-    OAM_PARFWDCPU
-};
-
-enum OAMMULACT
-{
-    OAM_MULFWD = 0,
-    OAM_MULDISCARD,
-    OAM_MULCPU
-};
-
-extern ret_t rtl8367c_setAsicOamParser(rtk_uint32 port, rtk_uint32 parser);
-extern ret_t rtl8367c_getAsicOamParser(rtk_uint32 port, rtk_uint32* pParser);
-extern ret_t rtl8367c_setAsicOamMultiplexer(rtk_uint32 port, rtk_uint32 multiplexer);
-extern ret_t rtl8367c_getAsicOamMultiplexer(rtk_uint32 port, rtk_uint32* pMultiplexer);
-extern ret_t rtl8367c_setAsicOamCpuPri(rtk_uint32 priority);
-extern ret_t rtl8367c_getAsicOamCpuPri(rtk_uint32 *pPriority);
-extern ret_t rtl8367c_setAsicOamEnable(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicOamEnable(rtk_uint32 *pEnabled);
-#endif /*_RTL8367C_ASICDRV_OAM_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_phy.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_phy.h
deleted file mode 100644
index e993d6edf7..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_phy.h
+++ /dev/null
@@ -1,43 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : PHY related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_PHY_H_
-#define _RTL8367C_ASICDRV_PHY_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_PHY_REGNOMAX           0x1F
-#define RTL8367C_PHY_EXTERNALMAX        0x7
-
-#define RTL8367C_PHY_BASE               0x2000
-#define RTL8367C_PHY_EXT_BASE           0xA000
-
-#define RTL8367C_PHY_OFFSET             5
-#define RTL8367C_PHY_EXT_OFFSET         9
-
-#define RTL8367C_PHY_PAGE_ADDRESS       31
-
-
-extern ret_t rtl8367c_setAsicPHYReg(rtk_uint32 phyNo, rtk_uint32 phyAddr, rtk_uint32 regData );
-extern ret_t rtl8367c_getAsicPHYReg(rtk_uint32 phyNo, rtk_uint32 phyAddr, rtk_uint32* pRegData );
-extern ret_t rtl8367c_setAsicPHYOCPReg(rtk_uint32 phyNo, rtk_uint32 ocpAddr, rtk_uint32 ocpData );
-extern ret_t rtl8367c_getAsicPHYOCPReg(rtk_uint32 phyNo, rtk_uint32 ocpAddr, rtk_uint32 *pRegData );
-extern ret_t rtl8367c_setAsicSdsReg(rtk_uint32 sdsId, rtk_uint32 sdsReg, rtk_uint32 sdsPage,  rtk_uint32 value);
-extern ret_t rtl8367c_getAsicSdsReg(rtk_uint32 sdsId, rtk_uint32 sdsReg, rtk_uint32 sdsPage, rtk_uint32 *value);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_PHY_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_port.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_port.h
deleted file mode 100644
index ad99d8560b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_port.h
+++ /dev/null
@@ -1,237 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76333 $
- * $Date: 2017-03-09 09:33:15 +0800 (¶g¥|, 09 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port security related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_PORTSECURITY_H_
-#define _RTL8367C_ASICDRV_PORTSECURITY_H_
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_unknownMulticast.h>
-#include <rtl8367c_asicdrv_phy.h>
-
-/****************************************************************/
-/* Type Definition                                              */
-/****************************************************************/
-
-#define RTL8367C_MAC7       7
-#define RTL8367C_EXTNO       3
-
-#define RTL8367C_RTCT_PAGE          (11)
-#define RTL8367C_RTCT_RESULT_A_REG  (27)
-#define RTL8367C_RTCT_RESULT_B_REG  (28)
-#define RTL8367C_RTCT_RESULT_C_REG  (29)
-#define RTL8367C_RTCT_RESULT_D_REG  (30)
-#define RTL8367C_RTCT_STATUS_REG    (26)
-
-enum L2_SECURITY_BEHAVE
-{
-    L2_BEHAVE_FLOODING = 0,
-    L2_BEHAVE_DROP,
-    L2_BEHAVE_TRAP,
-    L2_BEHAVE_END
-};
-
-enum L2_UNDA_BEHAVE
-{
-    L2_UNDA_BEHAVE_FLOODING_PMASK = 0,
-    L2_UNDA_BEHAVE_DROP,
-    L2_UNDA_BEHAVE_TRAP,
-    L2_UNDA_BEHAVE_FLOODING,
-    L2_UNDA_BEHAVE_END
-};
-
-enum L2_SECURITY_SA_BEHAVE
-{
-    L2_BEHAVE_SA_FLOODING = 0,
-    L2_BEHAVE_SA_DROP,
-    L2_BEHAVE_SA_TRAP,
-    L2_BEHAVE_SA_COPY28051,
-    L2_BEHAVE_SA_END
-};
-
-/* enum for port current link speed */
-enum SPEEDMODE
-{
-    SPD_10M = 0,
-    SPD_100M,
-    SPD_1000M,
-    SPD_2500M
-};
-
-/* enum for mac link mode */
-enum LINKMODE
-{
-    MAC_NORMAL = 0,
-    MAC_FORCE,
-};
-
-/* enum for port current link duplex mode */
-enum DUPLEXMODE
-{
-    HALF_DUPLEX = 0,
-    FULL_DUPLEX
-};
-
-/* enum for port current MST mode */
-enum MSTMODE
-{
-    SLAVE_MODE= 0,
-    MASTER_MODE
-};
-
-
-enum EXTMODE
-{
-    EXT_DISABLE = 0,
-    EXT_RGMII,
-    EXT_MII_MAC,
-    EXT_MII_PHY,
-    EXT_TMII_MAC,
-    EXT_TMII_PHY,
-    EXT_GMII,
-    EXT_RMII_MAC,
-    EXT_RMII_PHY,
-    EXT_SGMII,
-    EXT_HSGMII,
-    EXT_1000X_100FX,
-    EXT_1000X,
-    EXT_100FX,
-    EXT_RGMII_2,
-    EXT_MII_MAC_2,
-    EXT_MII_PHY_2,
-    EXT_TMII_MAC_2,
-    EXT_TMII_PHY_2,
-    EXT_RMII_MAC_2,
-    EXT_RMII_PHY_2,
-    EXT_END
-};
-
-enum DOSTYPE
-{
-    DOS_DAEQSA = 0,
-    DOS_LANDATTACKS,
-    DOS_BLATATTACKS,
-    DOS_SYNFINSCAN,
-    DOS_XMASCAN,
-    DOS_NULLSCAN,
-    DOS_SYN1024,
-    DOS_TCPSHORTHDR,
-    DOS_TCPFRAGERROR,
-    DOS_ICMPFRAGMENT,
-    DOS_END,
-
-};
-
-typedef struct  rtl8367c_port_ability_s{
-    rtk_uint16 forcemode;
-    rtk_uint16 mstfault;
-    rtk_uint16 mstmode;
-    rtk_uint16 nway;
-    rtk_uint16 txpause;
-    rtk_uint16 rxpause;
-    rtk_uint16 link;
-    rtk_uint16 duplex;
-    rtk_uint16 speed;
-}rtl8367c_port_ability_t;
-
-typedef struct  rtl8367c_port_status_s{
-
-    rtk_uint16 lpi1000;
-    rtk_uint16 lpi100;
-    rtk_uint16 mstfault;
-    rtk_uint16 mstmode;
-    rtk_uint16 nway;
-    rtk_uint16 txpause;
-    rtk_uint16 rxpause;
-    rtk_uint16 link;
-    rtk_uint16 duplex;
-    rtk_uint16 speed;
-
-}rtl8367c_port_status_t;
-
-typedef struct rtct_result_s
-{
-    rtk_uint32      channelAShort;
-    rtk_uint32      channelBShort;
-    rtk_uint32      channelCShort;
-    rtk_uint32      channelDShort;
-
-    rtk_uint32      channelAOpen;
-    rtk_uint32      channelBOpen;
-    rtk_uint32      channelCOpen;
-    rtk_uint32      channelDOpen;
-
-    rtk_uint32      channelAMismatch;
-    rtk_uint32      channelBMismatch;
-    rtk_uint32      channelCMismatch;
-    rtk_uint32      channelDMismatch;
-
-    rtk_uint32      channelALinedriver;
-    rtk_uint32      channelBLinedriver;
-    rtk_uint32      channelCLinedriver;
-    rtk_uint32      channelDLinedriver;
-
-    rtk_uint32      channelALen;
-    rtk_uint32      channelBLen;
-    rtk_uint32      channelCLen;
-    rtk_uint32      channelDLen;
-} rtl8367c_port_rtct_result_t;
-
-
-/****************************************************************/
-/* Driver Proto Type Definition                                 */
-/****************************************************************/
-extern ret_t rtl8367c_setAsicPortUnknownDaBehavior(rtk_uint32 port, rtk_uint32 behavior);
-extern ret_t rtl8367c_getAsicPortUnknownDaBehavior(rtk_uint32 port, rtk_uint32 *pBehavior);
-extern ret_t rtl8367c_setAsicPortUnknownSaBehavior(rtk_uint32 behavior);
-extern ret_t rtl8367c_getAsicPortUnknownSaBehavior(rtk_uint32 *pBehavior);
-extern ret_t rtl8367c_setAsicPortUnmatchedSaBehavior(rtk_uint32 behavior);
-extern ret_t rtl8367c_getAsicPortUnmatchedSaBehavior(rtk_uint32 *pBehavior);
-extern ret_t rtl8367c_setAsicPortUnmatchedSaMoving(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortUnmatchedSaMoving(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicPortUnknownDaFloodingPortmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicPortUnknownDaFloodingPortmask(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicPortUnknownMulticastFloodingPortmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicPortUnknownMulticastFloodingPortmask(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicPortBcastFloodingPortmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicPortBcastFloodingPortmask(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicPortBlockSpa(rtk_uint32 port, rtk_uint32 block);
-extern ret_t rtl8367c_getAsicPortBlockSpa(rtk_uint32 port, rtk_uint32 *pBlock);
-extern ret_t rtl8367c_setAsicPortForceLink(rtk_uint32 port, rtl8367c_port_ability_t *pPortAbility);
-extern ret_t rtl8367c_getAsicPortForceLink(rtk_uint32 port, rtl8367c_port_ability_t *pPortAbility);
-extern ret_t rtl8367c_getAsicPortStatus(rtk_uint32 port, rtl8367c_port_status_t *pPortStatus);
-extern ret_t rtl8367c_setAsicPortForceLinkExt(rtk_uint32 id, rtl8367c_port_ability_t *pPortAbility);
-extern ret_t rtl8367c_getAsicPortForceLinkExt(rtk_uint32 id, rtl8367c_port_ability_t *pPortAbility);
-extern ret_t rtl8367c_setAsicPortExtMode(rtk_uint32 id, rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicPortExtMode(rtk_uint32 id, rtk_uint32 *pMode);
-extern ret_t rtl8367c_setAsicPortDos(rtk_uint32 type, rtk_uint32 drop);
-extern ret_t rtl8367c_getAsicPortDos(rtk_uint32 type, rtk_uint32* pDrop);
-extern ret_t rtl8367c_setAsicPortEnableAll(rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicPortEnableAll(rtk_uint32 *pEnable);
-extern ret_t rtl8367c_setAsicPortSmallIpg(rtk_uint32 port, rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicPortSmallIpg(rtk_uint32 port, rtk_uint32* pEnable);
-extern ret_t rtl8367c_setAsicPortLoopback(rtk_uint32 port, rtk_uint32 enable);
-extern ret_t rtl8367c_getAsicPortLoopback(rtk_uint32 port, rtk_uint32 *pEnable);
-extern ret_t rtl8367c_setAsicPortRTCTEnable(rtk_uint32 portmask);
-extern ret_t rtl8367c_setAsicPortRTCTDisable(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicPortRTCTResult(rtk_uint32 port, rtl8367c_port_rtct_result_t *pResult);
-extern ret_t rtl8367c_sdsReset(rtk_uint32 id);
-extern ret_t rtl8367c_getSdsLinkStatus(rtk_uint32 ext_id, rtk_uint32 *pSignalDetect, rtk_uint32 *pSync, rtk_uint32 *pLink);
-extern ret_t rtl8367c_setSgmiiNway(rtk_uint32 ext_id, rtk_uint32 state);
-extern ret_t rtl8367c_getSgmiiNway(rtk_uint32 ext_id, rtk_uint32 *pState);
-
-#endif /*_RTL8367C_ASICDRV_PORTSECURITY_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_portIsolation.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_portIsolation.h
deleted file mode 100644
index e23d88e81f..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_portIsolation.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port isolation related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_PORTISOLATION_H_
-#define _RTL8367C_ASICDRV_PORTISOLATION_H_
-
-#include <rtl8367c_asicdrv.h>
-
-extern ret_t rtl8367c_setAsicPortIsolationPermittedPortmask(rtk_uint32 port, rtk_uint32 permitPortmask);
-extern ret_t rtl8367c_getAsicPortIsolationPermittedPortmask(rtk_uint32 port, rtk_uint32 *pPermitPortmask);
-extern ret_t rtl8367c_setAsicPortIsolationEfid(rtk_uint32 port, rtk_uint32 efid);
-extern ret_t rtl8367c_getAsicPortIsolationEfid(rtk_uint32 port, rtk_uint32 *pEfid);
-
-#endif /*_RTL8367C_ASICDRV_PORTISOLATION_H_*/
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_qos.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_qos.h
deleted file mode 100644
index 26042bfa13..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_qos.h
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Qos related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_QOS_H_
-#define _RTL8367C_ASICDRV_QOS_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_DECISIONPRIMAX    0xFF
-
-/* enum Priority Selection Types */
-enum PRIDECISION
-{
-    PRIDEC_PORT = 0,
-    PRIDEC_ACL,
-    PRIDEC_DSCP,
-    PRIDEC_1Q,
-    PRIDEC_1AD,
-    PRIDEC_CVLAN,
-    PRIDEC_DA,
-    PRIDEC_SA,
-    PRIDEC_END,
-};
-
-/* enum Priority Selection Index */
-enum RTL8367C_PRIDEC_TABLE
-{
-    PRIDEC_IDX0 = 0,
-    PRIDEC_IDX1,
-    PRIDEC_IDX_END,
-};
-
-enum RTL8367C_DOT1P_PRISEL
-{
-    DOT1P_PRISEL_USER =  0,
-    DOT1P_PRISEL_TAG,
-    DOT1P_PRISEL_END
-};
-
-enum RTL8367C_DSCP_PRISEL
-{
-    DSCP_PRISEL_INTERNAL =  0,
-    DSCP_PRISEL_DSCP,
-    DSCP_PRISEL_USER ,
-    DSCP_PRISEL_END
-};
-
-
-extern ret_t rtl8367c_setAsicRemarkingDot1pAbility(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicRemarkingDot1pAbility(rtk_uint32 port, rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicRemarkingDot1pParameter(rtk_uint32 priority, rtk_uint32 newPriority );
-extern ret_t rtl8367c_getAsicRemarkingDot1pParameter(rtk_uint32 priority, rtk_uint32 *pNewPriority );
-extern  ret_t rtl8367c_setAsicRemarkingDot1pSrc(rtk_uint32 type);
-extern  ret_t rtl8367c_getAsicRemarkingDot1pSrc(rtk_uint32 *pType);
-extern ret_t rtl8367c_setAsicRemarkingDscpAbility(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicRemarkingDscpAbility(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicRemarkingDscpParameter(rtk_uint32 priority, rtk_uint32 newDscp );
-extern ret_t rtl8367c_getAsicRemarkingDscpParameter(rtk_uint32 priority, rtk_uint32* pNewDscp );
-
-extern ret_t rtl8367c_setAsicPriorityDot1qRemapping(rtk_uint32 srcpriority, rtk_uint32 priority );
-extern ret_t rtl8367c_getAsicPriorityDot1qRemapping(rtk_uint32 srcpriority, rtk_uint32 *pPriority );
-extern ret_t rtl8367c_setAsicPriorityDscpBased(rtk_uint32 dscp, rtk_uint32 priority );
-extern ret_t rtl8367c_getAsicPriorityDscpBased(rtk_uint32 dscp, rtk_uint32 *pPriority );
-extern ret_t rtl8367c_setAsicPriorityPortBased(rtk_uint32 port, rtk_uint32 priority );
-extern ret_t rtl8367c_getAsicPriorityPortBased(rtk_uint32 port, rtk_uint32 *pPriority );
-extern ret_t rtl8367c_setAsicPriorityDecision(rtk_uint32 index, rtk_uint32 prisrc, rtk_uint32 decisionPri);
-extern ret_t rtl8367c_getAsicPriorityDecision(rtk_uint32 index, rtk_uint32 prisrc, rtk_uint32* pDecisionPri);
-extern ret_t rtl8367c_setAsicPriorityToQIDMappingTable(rtk_uint32 qnum, rtk_uint32 priority, rtk_uint32 qid );
-extern ret_t rtl8367c_getAsicPriorityToQIDMappingTable(rtk_uint32 qnum, rtk_uint32 priority, rtk_uint32* pQid);
-extern ret_t rtl8367c_setAsicOutputQueueMappingIndex(rtk_uint32 port, rtk_uint32 qnum );
-extern ret_t rtl8367c_getAsicOutputQueueMappingIndex(rtk_uint32 port, rtk_uint32 *pQnum );
-
-extern ret_t rtl8367c_setAsicRemarkingDscpSrc(rtk_uint32 type);
-extern ret_t rtl8367c_getAsicRemarkingDscpSrc(rtk_uint32 *pType);
-extern ret_t rtl8367c_setAsicRemarkingDscp2Dscp(rtk_uint32 dscp, rtk_uint32 rmkDscp);
-extern ret_t rtl8367c_getAsicRemarkingDscp2Dscp(rtk_uint32 dscp, rtk_uint32 *pRmkDscp);
-
-extern ret_t rtl8367c_setAsicPortPriorityDecisionIndex(rtk_uint32 port, rtk_uint32 index );
-extern ret_t rtl8367c_getAsicPortPriorityDecisionIndex(rtk_uint32 port, rtk_uint32 *pIndex );
-
-#endif /*#ifndef _RTL8367C_ASICDRV_QOS_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_rldp.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_rldp.h
deleted file mode 100644
index cde970b638..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_rldp.h
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 42321 $
- * $Date: 2013-08-26 13:51:29 +0800 (¶g¤@, 26 ¤K¤ë 2013) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : RLDP related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_RLDP_H_
-#define _RTL8367C_ASICDRV_RLDP_H_
-
-#include <rtl8367c_asicdrv.h>
-#include <string.h>
-
-extern ret_t rtl8367c_setAsicRldp(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicRldp(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicRldpEnable8051(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicRldpEnable8051(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicRldpCompareRandomNumber(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicRldpCompareRandomNumber(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicRldpIndicatorSource(rtk_uint32 src);
-extern ret_t rtl8367c_getAsicRldpIndicatorSource(rtk_uint32 *pSrc);
-extern ret_t rtl8367c_setAsicRldpCheckingStatePara(rtk_uint32 retryCount, rtk_uint32 retryPeriod);
-extern ret_t rtl8367c_getAsicRldpCheckingStatePara(rtk_uint32 *pRetryCount, rtk_uint32 *pRetryPeriod);
-extern ret_t rtl8367c_setAsicRldpLoopStatePara(rtk_uint32 retryCount, rtk_uint32 retryPeriod);
-extern ret_t rtl8367c_getAsicRldpLoopStatePara(rtk_uint32 *pRetryCount, rtk_uint32 *pRetryPeriod);
-extern ret_t rtl8367c_setAsicRldpTxPortmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicRldpTxPortmask(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicRldpMagicNum(ether_addr_t seed);
-extern ret_t rtl8367c_getAsicRldpMagicNum(ether_addr_t *pSeed);
-extern ret_t rtl8367c_getAsicRldpLoopedPortmask(rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicRldp8051Portmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicRldp8051Portmask(rtk_uint32 *pPortmask);
-
-
-extern ret_t rtl8367c_getAsicRldpRandomNumber(ether_addr_t *pRandNumber);
-extern ret_t rtl8367c_getAsicRldpLoopedPortPair(rtk_uint32 port, rtk_uint32 *pLoopedPair);
-extern ret_t rtl8367c_setAsicRlppTrap8051(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicRlppTrap8051(rtk_uint32 *pEnabled);
-
-extern ret_t rtl8367c_setAsicRldpLeaveLoopedPortmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicRldpLeaveLoopedPortmask(rtk_uint32 *pPortmask);
-
-extern ret_t rtl8367c_setAsicRldpEnterLoopedPortmask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicRldpEnterLoopedPortmask(rtk_uint32 *pPortmask);
-
-extern ret_t rtl8367c_setAsicRldpTriggerMode(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicRldpTriggerMode(rtk_uint32 *pEnabled);
-
-#endif /*_RTL8367C_ASICDRV_RLDP_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_rma.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_rma.h
deleted file mode 100644
index 10c707544f..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_rma.h
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 64716 $
- * $Date: 2015-12-31 16:31:55 +0800 (¶g¥|, 31 ¤Q¤G¤ë 2015) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : RMA related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_RMA_H_
-#define _RTL8367C_ASICDRV_RMA_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_RMAMAX                     0x2F
-
-enum RTL8367C_RMAOP
-{
-    RMAOP_FORWARD = 0,
-    RMAOP_TRAP_TO_CPU,
-    RMAOP_DROP,
-    RMAOP_FORWARD_EXCLUDE_CPU,
-    RMAOP_END
-};
-
-
-typedef struct  rtl8367c_rma_s{
-
-    rtk_uint16 operation;
-    rtk_uint16 discard_storm_filter;
-    rtk_uint16 trap_priority;
-    rtk_uint16 keep_format;
-    rtk_uint16 vlan_leaky;
-    rtk_uint16 portiso_leaky;
-
-}rtl8367c_rma_t;
-
-
-extern ret_t rtl8367c_setAsicRma(rtk_uint32 index, rtl8367c_rma_t* pRmacfg);
-extern ret_t rtl8367c_getAsicRma(rtk_uint32 index, rtl8367c_rma_t* pRmacfg);
-extern ret_t rtl8367c_setAsicRmaCdp(rtl8367c_rma_t* pRmacfg);
-extern ret_t rtl8367c_getAsicRmaCdp(rtl8367c_rma_t* pRmacfg);
-extern ret_t rtl8367c_setAsicRmaCsstp(rtl8367c_rma_t* pRmacfg);
-extern ret_t rtl8367c_getAsicRmaCsstp(rtl8367c_rma_t* pRmacfg);
-extern ret_t rtl8367c_setAsicRmaLldp(rtk_uint32 enabled, rtl8367c_rma_t* pRmacfg);
-extern ret_t rtl8367c_getAsicRmaLldp(rtk_uint32 *pEnabled, rtl8367c_rma_t* pRmacfg);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_RMA_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_scheduling.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_scheduling.h
deleted file mode 100644
index 919a4ca692..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_scheduling.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Packet Scheduling related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_SCHEDULING_H_
-#define _RTL8367C_ASICDRV_SCHEDULING_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_QWEIGHTMAX    0x7F
-#define RTL8367C_PORT_QUEUE_METER_INDEX_MAX    7
-
-/* enum for queue type */
-enum QUEUETYPE
-{
-    QTYPE_STRICT = 0,
-    QTYPE_WFQ,
-};
-extern ret_t rtl8367c_setAsicLeakyBucketParameter(rtk_uint32 tick, rtk_uint32 token);
-extern ret_t rtl8367c_getAsicLeakyBucketParameter(rtk_uint32 *tick, rtk_uint32 *token);
-extern ret_t rtl8367c_setAsicAprMeter(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 apridx);
-extern ret_t rtl8367c_getAsicAprMeter(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 *apridx);
-extern ret_t rtl8367c_setAsicPprMeter(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 ppridx);
-extern ret_t rtl8367c_getAsicPprMeter(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 *ppridx);
-extern ret_t rtl8367c_setAsicAprEnable(rtk_uint32 port, rtk_uint32 aprEnable);
-extern ret_t rtl8367c_getAsicAprEnable(rtk_uint32 port, rtk_uint32 *aprEnable);
-extern ret_t rtl8367c_setAsicPprEnable(rtk_uint32 port, rtk_uint32 pprEnable);
-extern ret_t rtl8367c_getAsicPprEnable(rtk_uint32 port, rtk_uint32 *pprEnable);
-
-extern ret_t rtl8367c_setAsicWFQWeight(rtk_uint32, rtk_uint32 queueid, rtk_uint32 weight );
-extern ret_t rtl8367c_getAsicWFQWeight(rtk_uint32, rtk_uint32 queueid, rtk_uint32 *weight );
-extern ret_t rtl8367c_setAsicWFQBurstSize(rtk_uint32 burstsize);
-extern ret_t rtl8367c_getAsicWFQBurstSize(rtk_uint32 *burstsize);
-
-extern ret_t rtl8367c_setAsicQueueType(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 queueType);
-extern ret_t rtl8367c_getAsicQueueType(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 *queueType);
-extern ret_t rtl8367c_setAsicQueueRate(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 ppridx, rtk_uint32 apridx );
-extern ret_t rtl8367c_getAsicQueueRate(rtk_uint32 port, rtk_uint32 qid, rtk_uint32* ppridx, rtk_uint32* apridx );
-extern ret_t rtl8367c_setAsicPortEgressRate(rtk_uint32 port, rtk_uint32 rate);
-extern ret_t rtl8367c_getAsicPortEgressRate(rtk_uint32 port, rtk_uint32 *rate);
-extern ret_t rtl8367c_setAsicPortEgressRateIfg(rtk_uint32 ifg);
-extern ret_t rtl8367c_getAsicPortEgressRateIfg(rtk_uint32 *ifg);
-
-#endif /*_RTL8367C_ASICDRV_SCHEDULING_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_storm.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_storm.h
deleted file mode 100644
index 3865b5225a..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_storm.h
+++ /dev/null
@@ -1,61 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Storm control filtering related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_STORM_H_
-#define _RTL8367C_ASICDRV_STORM_H_
-
-#include <rtl8367c_asicdrv.h>
-
-extern ret_t rtl8367c_setAsicStormFilterBroadcastEnable(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterBroadcastEnable(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterBroadcastMeter(rtk_uint32 port, rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterBroadcastMeter(rtk_uint32 port, rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterMulticastEnable(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterMulticastEnable(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterMulticastMeter(rtk_uint32 port, rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterMulticastMeter(rtk_uint32 port, rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterUnknownMulticastEnable(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterUnknownMulticastEnable(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterUnknownMulticastMeter(rtk_uint32 port, rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterUnknownMulticastMeter(rtk_uint32 port, rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterUnknownUnicastEnable(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterUnknownUnicastEnable(rtk_uint32 port, rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterUnknownUnicastMeter(rtk_uint32 port, rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterUnknownUnicastMeter(rtk_uint32 port, rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterExtBroadcastMeter(rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterExtBroadcastMeter(rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterExtMulticastMeter(rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterExtMulticastMeter(rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterExtUnknownMulticastMeter(rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterExtUnknownMulticastMeter(rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterExtUnknownUnicastMeter(rtk_uint32 meter);
-extern ret_t rtl8367c_getAsicStormFilterExtUnknownUnicastMeter(rtk_uint32 *pMeter);
-extern ret_t rtl8367c_setAsicStormFilterExtBroadcastEnable(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterExtBroadcastEnable(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterExtMulticastEnable(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterExtMulticastEnable(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterExtUnknownMulticastEnable(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterExtUnknownMulticastEnable(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterExtUnknownUnicastEnable(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicStormFilterExtUnknownUnicastEnable(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_setAsicStormFilterExtEnablePortMask(rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicStormFilterExtEnablePortMask(rtk_uint32 *pPortmask);
-
-
-#endif /*_RTL8367C_ASICDRV_STORM_H_*/
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_svlan.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_svlan.h
deleted file mode 100644
index 5a6a4a8329..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_svlan.h
+++ /dev/null
@@ -1,132 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : SVLAN related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_SVLAN_H_
-#define _RTL8367C_ASICDRV_SVLAN_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_C2SIDXNO               128
-#define RTL8367C_C2SIDXMAX              (RTL8367C_C2SIDXNO-1)
-#define RTL8367C_MC2SIDXNO              32
-#define RTL8367C_MC2SIDXMAX             (RTL8367C_MC2SIDXNO-1)
-#define RTL8367C_SP2CIDXNO              128
-#define RTL8367C_SP2CMAX                (RTL8367C_SP2CIDXNO-1)
-
-#define RTL8367C_SVLAN_MEMCONF_LEN      4
-#define RTL8367C_SVLAN_MC2S_LEN         5
-#define RTL8367C_SVLAN_SP2C_LEN         2
-
-enum RTL8367C_SPRISEL
-{
-    SPRISEL_INTERNALPRI =  0,
-    SPRISEL_CTAGPRI,
-    SPRISEL_VSPRI,
-    SPRISEL_PBPRI,
-    SPRISEL_END
-};
-
-enum RTL8367C_SUNACCEPT
-{
-    SUNACCEPT_DROP =  0,
-    SUNACCEPT_TRAP,
-    SUNACCEPT_SVLAN,
-    SUNACCEPT_END
-};
-
-enum RTL8367C_SVLAN_MC2S_MODE
-{
-    SVLAN_MC2S_MODE_MAC =  0,
-    SVLAN_MC2S_MODE_IP,
-    SVLAN_MC2S_MODE_END
-};
-
-
-typedef struct  rtl8367c_svlan_memconf_s{
-
-    rtk_uint16 vs_member:11;
-    rtk_uint16 vs_untag:11;
-
-    rtk_uint16 vs_fid_msti:4;
-    rtk_uint16 vs_priority:3;
-    rtk_uint16 vs_force_fid:1;
-    rtk_uint16 reserved:8;
-
-    rtk_uint16 vs_svid:12;
-    rtk_uint16 vs_efiden:1;
-    rtk_uint16 vs_efid:3;
-
-
-}rtl8367c_svlan_memconf_t;
-
-
-typedef struct  rtl8367c_svlan_mc2s_s{
-
-    rtk_uint16 valid:1;
-    rtk_uint16 format:1;
-    rtk_uint16 svidx:6;
-    rtk_uint32 sdata;
-    rtk_uint32 smask;
-}rtl8367c_svlan_mc2s_t;
-
-
-typedef struct  rtl8367c_svlan_s2c_s{
-
-    rtk_uint16 valid:1;
-    rtk_uint16 svidx:6;
-    rtk_uint16 dstport:4;
-    rtk_uint32 vid:12;
-}rtl8367c_svlan_s2c_t;
-
-extern ret_t rtl8367c_setAsicSvlanIngressUntag(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicSvlanIngressUntag(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicSvlanIngressUnmatch(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicSvlanIngressUnmatch(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicSvlanTrapPriority(rtk_uint32 priority);
-extern ret_t rtl8367c_getAsicSvlanTrapPriority(rtk_uint32* pPriority);
-extern ret_t rtl8367c_setAsicSvlanDefaultVlan(rtk_uint32 port, rtk_uint32 index);
-extern ret_t rtl8367c_getAsicSvlanDefaultVlan(rtk_uint32 port, rtk_uint32* pIndex);
-
-extern ret_t rtl8367c_setAsicSvlanMemberConfiguration(rtk_uint32 index,rtl8367c_svlan_memconf_t* pSvlanMemCfg);
-extern ret_t rtl8367c_getAsicSvlanMemberConfiguration(rtk_uint32 index,rtl8367c_svlan_memconf_t* pSvlanMemCfg);
-
-extern ret_t rtl8367c_setAsicSvlanPrioritySel(rtk_uint32 priSel);
-extern ret_t rtl8367c_getAsicSvlanPrioritySel(rtk_uint32* pPriSel);
-extern ret_t rtl8367c_setAsicSvlanTpid(rtk_uint32 protocolType);
-extern ret_t rtl8367c_getAsicSvlanTpid(rtk_uint32* pProtocolType);
-extern ret_t rtl8367c_setAsicSvlanUplinkPortMask(rtk_uint32 portMask);
-extern ret_t rtl8367c_getAsicSvlanUplinkPortMask(rtk_uint32* pPortmask);
-extern ret_t rtl8367c_setAsicSvlanEgressUnassign(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicSvlanEgressUnassign(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicSvlanC2SConf(rtk_uint32 index, rtk_uint32 evid, rtk_uint32 portmask, rtk_uint32 svidx);
-extern ret_t rtl8367c_getAsicSvlanC2SConf(rtk_uint32 index, rtk_uint32* pEvid, rtk_uint32* pPortmask, rtk_uint32* pSvidx);
-extern ret_t rtl8367c_setAsicSvlanMC2SConf(rtk_uint32 index,rtl8367c_svlan_mc2s_t* pSvlanMc2sCfg);
-extern ret_t rtl8367c_getAsicSvlanMC2SConf(rtk_uint32 index,rtl8367c_svlan_mc2s_t* pSvlanMc2sCfg);
-extern ret_t rtl8367c_setAsicSvlanSP2CConf(rtk_uint32 index,rtl8367c_svlan_s2c_t* pSvlanSp2cCfg);
-extern ret_t rtl8367c_getAsicSvlanSP2CConf(rtk_uint32 index,rtl8367c_svlan_s2c_t* pSvlanSp2cCfg);
-extern ret_t rtl8367c_setAsicSvlanDmacCvidSel(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicSvlanDmacCvidSel(rtk_uint32 port, rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicSvlanUntagVlan(rtk_uint32 index);
-extern ret_t rtl8367c_getAsicSvlanUntagVlan(rtk_uint32* pIndex);
-extern ret_t rtl8367c_setAsicSvlanUnmatchVlan(rtk_uint32 index);
-extern ret_t rtl8367c_getAsicSvlanUnmatchVlan(rtk_uint32* pIndex);
-extern ret_t rtl8367c_setAsicSvlanLookupType(rtk_uint32 type);
-extern ret_t rtl8367c_getAsicSvlanLookupType(rtk_uint32* pType);
-
-
-#endif /*#ifndef _RTL8367C_ASICDRV_SVLAN_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_trunking.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_trunking.h
deleted file mode 100644
index 2e3a682819..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_trunking.h
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port trunking related functions
- *
- */
-
-
-#ifndef _RTL8367C_ASICDRV_TRUNKING_H_
-#define _RTL8367C_ASICDRV_TRUNKING_H_
-
-#include <rtl8367c_asicdrv.h>
-
-#define RTL8367C_MAX_TRUNK_GID              (2)
-#define RTL8367C_TRUNKING_PORTNO            (4)
-#define RTL8367C_TRUNKING1_PORTN0           (2)
-#define RTL8367C_TRUNKING_HASHVALUE_MAX     (15)
-
-extern ret_t rtl8367c_setAsicTrunkingGroup(rtk_uint32 group, rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicTrunkingGroup(rtk_uint32 group, rtk_uint32* pPortmask);
-extern ret_t rtl8367c_setAsicTrunkingFlood(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicTrunkingFlood(rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicTrunkingHashSelect(rtk_uint32 hashsel);
-extern ret_t rtl8367c_getAsicTrunkingHashSelect(rtk_uint32* pHashsel);
-
-extern ret_t rtl8367c_getAsicQeueuEmptyStatus(rtk_uint32* pPortmask);
-
-extern ret_t rtl8367c_setAsicTrunkingMode(rtk_uint32 mode);
-extern ret_t rtl8367c_getAsicTrunkingMode(rtk_uint32* pMode);
-extern ret_t rtl8367c_setAsicTrunkingFc(rtk_uint32 group, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicTrunkingFc(rtk_uint32 group, rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicTrunkingHashTable(rtk_uint32 hashval, rtk_uint32 portId);
-extern ret_t rtl8367c_getAsicTrunkingHashTable(rtk_uint32 hashval, rtk_uint32* pPortId);
-extern ret_t rtl8367c_setAsicTrunkingHashTable1(rtk_uint32 hashval, rtk_uint32 portId);
-extern ret_t rtl8367c_getAsicTrunkingHashTable1(rtk_uint32 hashval, rtk_uint32* pPortId);
-
-#endif /*_RTL8367C_ASICDRV_TRUNKING_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_unknownMulticast.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_unknownMulticast.h
deleted file mode 100644
index d142d25cff..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_unknownMulticast.h
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Unkown multicast related functions
- *
- */
-
-#ifndef _RTL8367C_ASICDRV_UNKNOWNMULTICAST_H_
-#define _RTL8367C_ASICDRV_UNKNOWNMULTICAST_H_
-
-#include <rtl8367c_asicdrv.h>
-
-enum L2_UNKOWN_MULTICAST_BEHAVE
-{
-    L2_UNKOWN_MULTICAST_FLOODING = 0,
-    L2_UNKOWN_MULTICAST_DROP,
-    L2_UNKOWN_MULTICAST_TRAP,
-    L2_UNKOWN_MULTICAST_DROP_EXCLUDE_RMA,
-    L2_UNKOWN_MULTICAST_END
-};
-
-enum L3_UNKOWN_MULTICAST_BEHAVE
-{
-    L3_UNKOWN_MULTICAST_FLOODING = 0,
-    L3_UNKOWN_MULTICAST_DROP,
-    L3_UNKOWN_MULTICAST_TRAP,
-    L3_UNKOWN_MULTICAST_ROUTER,
-    L3_UNKOWN_MULTICAST_END
-};
-
-enum MULTICASTTYPE{
-    MULTICAST_TYPE_IPV4 = 0,
-    MULTICAST_TYPE_IPV6,
-    MULTICAST_TYPE_L2,
-    MULTICAST_TYPE_END
-};
-
-extern ret_t rtl8367c_setAsicUnknownL2MulticastBehavior(rtk_uint32 port, rtk_uint32 behave);
-extern ret_t rtl8367c_getAsicUnknownL2MulticastBehavior(rtk_uint32 port, rtk_uint32 *pBehave);
-extern ret_t rtl8367c_setAsicUnknownIPv4MulticastBehavior(rtk_uint32 port, rtk_uint32 behave);
-extern ret_t rtl8367c_getAsicUnknownIPv4MulticastBehavior(rtk_uint32 port, rtk_uint32 *pBehave);
-extern ret_t rtl8367c_setAsicUnknownIPv6MulticastBehavior(rtk_uint32 port, rtk_uint32 behave);
-extern ret_t rtl8367c_getAsicUnknownIPv6MulticastBehavior(rtk_uint32 port, rtk_uint32 *pBehave);
-extern ret_t rtl8367c_setAsicUnknownMulticastTrapPriority(rtk_uint32 priority);
-extern ret_t rtl8367c_getAsicUnknownMulticastTrapPriority(rtk_uint32 *pPriority);
-
-#endif /*_RTL8367C_ASICDRV_UNKNOWNMULTICAST_H_*/
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_vlan.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_vlan.h
deleted file mode 100644
index 61848650b5..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_asicdrv_vlan.h
+++ /dev/null
@@ -1,157 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : VLAN related functions
- *
- */
-
-
-#ifndef _RTL8367C_ASICDRV_VLAN_H_
-#define _RTL8367C_ASICDRV_VLAN_H_
-
-/****************************************************************/
-/* Header File inclusion                                        */
-/****************************************************************/
-#include <rtl8367c_asicdrv.h>
-
-/****************************************************************/
-/* Constant Definition                                          */
-/****************************************************************/
-#define RTL8367C_PROTOVLAN_GIDX_MAX 3
-#define RTL8367C_PROTOVLAN_GROUPNO  4
-
-#define RTL8367C_VLAN_BUSY_CHECK_NO     (10)
-
-#define RTL8367C_VLAN_MBRCFG_LEN    (4)
-#define RTL8367C_VLAN_4KTABLE_LEN   (3)
-
-/****************************************************************/
-/* Type Definition                                              */
-/****************************************************************/
-typedef struct  VLANCONFIGUSER
-{
-    rtk_uint16  evid;
-    rtk_uint16  mbr;
-    rtk_uint16  fid_msti;
-    rtk_uint16  envlanpol;
-    rtk_uint16  meteridx;
-    rtk_uint16  vbpen;
-    rtk_uint16  vbpri;
-}rtl8367c_vlanconfiguser;
-
-typedef struct  USER_VLANTABLE{
-
-    rtk_uint16  vid;
-    rtk_uint16  mbr;
-    rtk_uint16  untag;
-    rtk_uint16  fid_msti;
-    rtk_uint16  envlanpol;
-    rtk_uint16  meteridx;
-    rtk_uint16  vbpen;
-    rtk_uint16  vbpri;
-    rtk_uint16  ivl_svl;
-
-}rtl8367c_user_vlan4kentry;
-
-typedef enum
-{
-    FRAME_TYPE_BOTH = 0,
-    FRAME_TYPE_TAGGED_ONLY,
-    FRAME_TYPE_UNTAGGED_ONLY,
-    FRAME_TYPE_MAX_BOUND
-} rtl8367c_accframetype;
-
-typedef enum
-{
-    EG_TAG_MODE_ORI = 0,
-    EG_TAG_MODE_KEEP,
-    EG_TAG_MODE_PRI_TAG,
-    EG_TAG_MODE_REAL_KEEP,
-    EG_TAG_MODE_END
-} rtl8367c_egtagmode;
-
-typedef enum
-{
-    PPVLAN_FRAME_TYPE_ETHERNET = 0,
-    PPVLAN_FRAME_TYPE_LLC,
-    PPVLAN_FRAME_TYPE_RFC1042,
-    PPVLAN_FRAME_TYPE_END
-} rtl8367c_provlan_frametype;
-
-enum RTL8367C_STPST
-{
-    STPST_DISABLED = 0,
-    STPST_BLOCKING,
-    STPST_LEARNING,
-    STPST_FORWARDING
-};
-
-enum RTL8367C_RESVIDACT
-{
-    RES_VID_ACT_UNTAG = 0,
-    RES_VID_ACT_TAG,
-    RES_VID_ACT_END
-};
-
-typedef struct
-{
-    rtl8367c_provlan_frametype  frameType;
-    rtk_uint32                      etherType;
-} rtl8367c_protocolgdatacfg;
-
-typedef struct
-{
-    rtk_uint32 valid;
-    rtk_uint32 vlan_idx;
-    rtk_uint32 priority;
-} rtl8367c_protocolvlancfg;
-
-extern ret_t rtl8367c_setAsicVlanMemberConfig(rtk_uint32 index, rtl8367c_vlanconfiguser *pVlanCg);
-extern ret_t rtl8367c_getAsicVlanMemberConfig(rtk_uint32 index, rtl8367c_vlanconfiguser *pVlanCg);
-extern ret_t rtl8367c_setAsicVlan4kEntry(rtl8367c_user_vlan4kentry *pVlan4kEntry );
-extern ret_t rtl8367c_getAsicVlan4kEntry(rtl8367c_user_vlan4kentry *pVlan4kEntry );
-extern ret_t rtl8367c_setAsicVlanAccpetFrameType(rtk_uint32 port, rtl8367c_accframetype frameType);
-extern ret_t rtl8367c_getAsicVlanAccpetFrameType(rtk_uint32 port, rtl8367c_accframetype *pFrameType);
-extern ret_t rtl8367c_setAsicVlanIngressFilter(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicVlanIngressFilter(rtk_uint32 port, rtk_uint32 *pEnable);
-extern ret_t rtl8367c_setAsicVlanEgressTagMode(rtk_uint32 port, rtl8367c_egtagmode tagMode);
-extern ret_t rtl8367c_getAsicVlanEgressTagMode(rtk_uint32 port, rtl8367c_egtagmode *pTagMode);
-extern ret_t rtl8367c_setAsicVlanPortBasedVID(rtk_uint32 port, rtk_uint32 index, rtk_uint32 pri);
-extern ret_t rtl8367c_getAsicVlanPortBasedVID(rtk_uint32 port, rtk_uint32 *pIndex, rtk_uint32 *pPri);
-extern ret_t rtl8367c_setAsicVlanProtocolBasedGroupData(rtk_uint32 index, rtl8367c_protocolgdatacfg *pPbCfg);
-extern ret_t rtl8367c_getAsicVlanProtocolBasedGroupData(rtk_uint32 index, rtl8367c_protocolgdatacfg *pPbCfg);
-extern ret_t rtl8367c_setAsicVlanPortAndProtocolBased(rtk_uint32 port, rtk_uint32 index, rtl8367c_protocolvlancfg *pPpbCfg);
-extern ret_t rtl8367c_getAsicVlanPortAndProtocolBased(rtk_uint32 port, rtk_uint32 index, rtl8367c_protocolvlancfg *pPpbCfg);
-extern ret_t rtl8367c_setAsicVlanFilter(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicVlanFilter(rtk_uint32* pEnabled);
-
-extern ret_t rtl8367c_setAsicPortBasedFid(rtk_uint32 port, rtk_uint32 fid);
-extern ret_t rtl8367c_getAsicPortBasedFid(rtk_uint32 port, rtk_uint32* pFid);
-extern ret_t rtl8367c_setAsicPortBasedFidEn(rtk_uint32 port, rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicPortBasedFidEn(rtk_uint32 port, rtk_uint32* pEnabled);
-extern ret_t rtl8367c_setAsicSpanningTreeStatus(rtk_uint32 port, rtk_uint32 msti, rtk_uint32 state);
-extern ret_t rtl8367c_getAsicSpanningTreeStatus(rtk_uint32 port, rtk_uint32 msti, rtk_uint32* pState);
-extern ret_t rtl8367c_setAsicVlanUntagDscpPriorityEn(rtk_uint32 enabled);
-extern ret_t rtl8367c_getAsicVlanUntagDscpPriorityEn(rtk_uint32* enabled);
-extern ret_t rtl8367c_setAsicVlanTransparent(rtk_uint32 port, rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicVlanTransparent(rtk_uint32 port, rtk_uint32 *pPortmask);
-extern ret_t rtl8367c_setAsicVlanEgressKeep(rtk_uint32 port, rtk_uint32 portmask);
-extern ret_t rtl8367c_getAsicVlanEgressKeep(rtk_uint32 port, rtk_uint32* pPortmask);
-extern ret_t rtl8367c_setReservedVidAction(rtk_uint32 vid0Action, rtk_uint32 vid4095Action);
-extern ret_t rtl8367c_getReservedVidAction(rtk_uint32 *pVid0Action, rtk_uint32 *pVid4095Action);
-extern ret_t rtl8367c_setRealKeepRemarkEn(rtk_uint32 enabled);
-extern ret_t rtl8367c_getRealKeepRemarkEn(rtk_uint32 *pEnabled);
-extern ret_t rtl8367c_resetVlan(void);
-
-#endif /*#ifndef _RTL8367C_ASICDRV_VLAN_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_base.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_base.h
deleted file mode 100644
index 676ca8ed74..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_base.h
+++ /dev/null
@@ -1,596 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Regsiter MACRO related definition
- *
- */
-
-#ifndef _RTL8367C_BASE_H_
-#define _RTL8367C_BASE_H_
-
-#include <rtl8367c_reg.h>
-
-/* (16'h0000) port_reg */
-
-#define    RTL8367C_PORT_SPECIAL_CONGEST_MODE_TIMER_BASE        RTL8367C_REG_PKTGEN_PORT0_TIMER
-#define    RTL8367C_PORT_SPECIAL_CONGEST_MODE_TIMER_REG(port)    (RTL8367C_PORT_SPECIAL_CONGEST_MODE_TIMER_BASE + (port << 5))
-
-#define    RTL8367C_PORT_MISC_CFG_BASE                            RTL8367C_REG_PORT0_MISC_CFG
-#define    RTL8367C_PORT_MISC_CFG_REG(port)                        (RTL8367C_PORT_MISC_CFG_BASE + (port << 5))
-#define    RTL8367C_1QREMARK_ENABLE_OFFSET                         RTL8367C_PORT0_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET
-#define    RTL8367C_1QREMARK_ENABLE_MASK                        RTL8367C_PORT0_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK
-
-#define    RTL8367C_INGRESSBW_PORT_IFG_MASK                        RTL8367C_PORT0_MISC_CFG_INGRESSBW_IFG_MASK
-#define    RTL8367C_VLAN_EGRESS_MDOE_MASK                        RTL8367C_PORT0_MISC_CFG_VLAN_EGRESS_MODE_MASK
-#define    RTL8367C_SPECIALCONGEST_SUSTAIN_TIMER_MASK            RTL8367C_PORT0_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK
-
-#define    RTL8367C_INGRESSBW_PORT_RATE_LSB_BASE                RTL8367C_REG_INGRESSBW_PORT0_RATE_CTRL0
-#define    RTL8367C_INGRESSBW_PORT_RATE_LSB_REG(port)            (RTL8367C_INGRESSBW_PORT_RATE_LSB_BASE + (port << 5))
-
-#define    RTL8367C_PORT_SMALL_IPG_REG(port)                    (RTL8367C_REG_PORT0_MISC_CFG + (port*0x20))
-
-#define    RTL8367C_PORT_EEE_CFG_BASE                           RTL8367C_REG_PORT0_EEECFG
-#define    RTL8367C_PORT_EEE_CFG_REG(port)                      (RTL8367C_REG_PORT0_EEECFG + (port << 5))
-#define    RTL8367C_PORT_EEE_100M_OFFSET                        RTL8367C_PORT0_EEECFG_EEE_100M_OFFSET
-#define    RTL8367C_PORT_EEE_100M_MASK                          RTL8367C_PORT0_EEECFG_EEE_100M_MASK
-#define    RTL8367C_PORT_EEE_GIGA_OFFSET                        RTL8367C_PORT0_EEECFG_EEE_GIGA_500M_OFFSET
-#define    RTL8367C_PORT_EEE_GIGA_MASK                          RTL8367C_PORT0_EEECFG_EEE_GIGA_500M_MASK
-
-
-/* (16'h0200) outq_reg */
-
-#define    RTL8367C_FLOWCTRL_QUEUE_DROP_ON_BASE                    RTL8367C_REG_FLOWCTRL_QUEUE0_DROP_ON
-#define    RTL8367C_FLOWCTRL_QUEUE_DROP_ON_REG(queue)            (RTL8367C_FLOWCTRL_QUEUE_DROP_ON_BASE + queue)
-#define    RTL8367C_FLOWCTRL_QUEUE_DROP_ON_MASK                    RTL8367C_FLOWCTRL_QUEUE0_DROP_ON_MASK
-
-#define    RTL8367C_FLOWCTRL_PORT_DROP_ON_BASE                    RTL8367C_REG_FLOWCTRL_PORT0_DROP_ON
-#define    RTL8367C_FLOWCTRL_PORT_DROP_ON_REG(PORT)                (RTL8367C_FLOWCTRL_PORT_DROP_ON_BASE + PORT)
-#define    RTL8367C_FLOWCTRL_PORT_DROP_ON_MASK                    RTL8367C_FLOWCTRL_PORT0_DROP_ON_MASK
-
-#define    RTL8367C_FLOWCTRL_PORT_GAP_REG                        RTL8367C_REG_FLOWCTRL_PORT_GAP
-#define    RTL8367C_FLOWCTRL_QUEUE_GAP_REG                        RTL8367C_REG_FLOWCTRL_QUEUE_GAP
-#define    RTL8367C_FLOWCTRL_PORT_QEMPTY_REG                    RTL8367C_REG_PORT_QEMPTY
-
-/* (16'h0300) sch_reg */
-
-#define    RTL8367C_SCHEDULE_WFQ_BURST_SIZE_REG                    RTL8367C_REG_SCHEDULE_WFQ_BURST_SIZE
-
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_BASE                    RTL8367C_REG_SCHEDULE_QUEUE_TYPE_CTRL0
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_REG(port)                (RTL8367C_SCHEDULE_QUEUE_TYPE_BASE + (port >> 1))
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_OFFSET(port, queue)        (((port & 0x1) << 3) + queue)
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_MASK(port, queue)         RTL8367C_SCHEDULE_QUEUE_TYPE_OFFSET(port, queue)
-
-#define    RTL8367C_SCHEDULE_PORT_QUEUE_WFQ_WEIGHT_BASE            RTL8367C_REG_SCHEDULE_PORT0_QUEUE0_WFQ_WEIGHT
-#define    RTL8367C_SCHEDULE_PORT_QUEUE_WFQ_WEIGHT_REG(port, queue)    (RTL8367C_SCHEDULE_PORT_QUEUE_WFQ_WEIGHT_BASE + (port << 3) + queue)
-
-#define    RTL8367C_SCHEDULE_APR_CTRL_REG                       RTL8367C_REG_SCHEDULE_APR_CTRL0
-#define    RTL8367C_SCHEDULE_APR_CTRL_OFFSET(port)                (port)
-#define    RTL8367C_SCHEDULE_APR_CTRL_MASK(port)                (1 << RTL8367C_SCHEDULE_APR_CTRL_OFFSET(port))
-
-#define    RTL8367C_SCHEDULE_PORT_APR_METER_BASE                RTL8367C_REG_SCHEDULE_PORT0_APR_METER_CTRL0
-#define    RTL8367C_SCHEDULE_PORT_APR_METER_REG(port, queue)    (RTL8367C_SCHEDULE_PORT_APR_METER_BASE + (port << 2) + (queue / 5))
-#define    RTL8367C_SCHEDULE_PORT_APR_METER_OFFSET(queue)        (3 * (queue % 5))
-#define    RTL8367C_SCHEDULE_PORT_APR_METER_MASK(queue)            (RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE0_APR_METER_MASK << RTL8367C_SCHEDULE_PORT_APR_METER_OFFSET(queue))
-
-#define    RTL8367C_PORT_EGRESSBW_LSB_BASE                        RTL8367C_REG_PORT0_EGRESSBW_CTRL0
-#define    RTL8367C_PORT_EGRESSBW_LSB_REG(port)                    (RTL8367C_PORT_EGRESSBW_LSB_BASE + (port << 1))
-
-#define    RTL8367C_PORT_EGRESSBW_MSB_BASE                        RTL8367C_REG_PORT0_EGRESSBW_CTRL1
-#define    RTL8367C_PORT_EGRESSBW_MSB_REG(port)                    (RTL8367C_PORT_EGRESSBW_MSB_BASE + (port << 1))
-
-/* (16'h0500) table_reg */
-
-#define    RTL8367C_TABLE_ACCESS_CTRL_REG                        RTL8367C_REG_TABLE_ACCESS_CTRL
-
-#define    RTL8367C_TABLE_ACCESS_ADDR_REG                        RTL8367C_REG_TABLE_ACCESS_ADDR
-
-#define    RTL8367C_TABLE_ACCESS_STATUS_REG                        RTL8367C_REG_TABLE_LUT_ADDR
-
-#define    RTL8367C_TABLE_ACCESS_WRDATA_BASE                    RTL8367C_REG_TABLE_WRITE_DATA0
-#define    RTL8367C_TABLE_ACCESS_WRDATA_REG(index)                (RTL8367C_TABLE_ACCESS_WRDATA_BASE + index)
-
-#define    RTL8367C_TABLE_ACCESS_RDDATA_BASE                    RTL8367C_REG_TABLE_READ_DATA0
-#define    RTL8367C_TABLE_ACCESS_RDDATA_REG(index)                (RTL8367C_TABLE_ACCESS_RDDATA_BASE + index)
-
-
-
-/* (16'h0600) acl_reg */
-
-#define    RTL8367C_ACL_RULE_TEMPLATE_CTRL_BASE                    RTL8367C_REG_ACL_RULE_TEMPLATE0_CTRL0
-#define    RTL8367C_ACL_RULE_TEMPLATE_CTRL_REG(template)        (RTL8367C_ACL_RULE_TEMPLATE_CTRL_BASE + template * 0x4)
-#define    RTL8367C_ACL_TEMPLATE_FIELD_OFFSET(field)            ((field & 0x01) <<3)
-#define    RTL8367C_ACL_TEMPLATE_FIELD_MASK(field)                (0x3F << RTL8367C_ACL_TEMPLATE_FIELD_OFFSET(field))
-
-#define    RTL8367C_ACL_ACTION_CTRL_BASE                        RTL8367C_REG_ACL_ACTION_CTRL0
-#define    RTL8367C_ACL_ACTION_CTRL_REG(rule)                   (RTL8367C_ACL_ACTION_CTRL_BASE + (rule >> 1))
-#define    RTL8367C_ACL_ACTION_CTRL2_BASE                        RTL8367C_REG_ACL_ACTION_CTRL32
-#define    RTL8367C_ACL_ACTION_CTRL2_REG(rule)                  (RTL8367C_ACL_ACTION_CTRL2_BASE + ((rule-64) >> 1))
-
-#define    RTL8367C_ACL_OP_NOT_OFFSET(rule)                        (6 + ((rule & 0x1) << 3))
-#define    RTL8367C_ACL_OP_NOT_MASK(rule)                        (1 << RTL8367C_ACL_OP_NOT_OFFSET(rule))
-#define    RTL8367C_ACL_OP_ACTION_OFFSET(rule)                    ((rule & 0x1) << 3)
-#define    RTL8367C_ACL_OP_ACTION_MASK(rule)                    (0x3F << RTL8367C_ACL_OP_ACTION_OFFSET(rule))
-
-#define    RTL8367C_ACL_ENABLE_REG                                RTL8367C_REG_ACL_ENABLE
-#define    RTL8367C_ACL_UNMATCH_PERMIT_REG                        RTL8367C_REG_ACL_UNMATCH_PERMIT
-
-/* (16'h0700) cvlan_reg */
-
-#define    RTL8367C_VLAN_PVID_CTRL_BASE                            RTL8367C_REG_VLAN_PVID_CTRL0
-#define    RTL8367C_VLAN_PVID_CTRL_REG(port)                    (RTL8367C_VLAN_PVID_CTRL_BASE + (port >> 1))
-#define    RTL8367C_PORT_VIDX_OFFSET(port)                        ((port &1)<<3)
-#define    RTL8367C_PORT_VIDX_MASK(port)                        (RTL8367C_PORT0_VIDX_MASK << RTL8367C_PORT_VIDX_OFFSET(port))
-
-#define    RTL8367C_VLAN_PPB_VALID_BASE                            RTL8367C_REG_VLAN_PPB0_VALID
-#define    RTL8367C_VLAN_PPB_VALID_REG(item)                    (RTL8367C_VLAN_PPB_VALID_BASE + (item << 3))
-
-#define    RTL8367C_VLAN_PPB_CTRL_BASE                            RTL8367C_REG_VLAN_PPB0_CTRL0
-#define    RTL8367C_VLAN_PPB_CTRL_REG(item, port)               (RTL8367C_VLAN_PPB_CTRL_BASE + (item << 3) + (port / 3) )
-#define    RTL8367C_VLAN_PPB_CTRL_OFFSET(port)                    ((port % 3) * 5)
-#define    RTL8367C_VLAN_PPB_CTRL_MASK(port)                    (RTL8367C_VLAN_PPB0_CTRL0_PORT0_INDEX_MASK << RTL8367C_VLAN_PPB_CTRL_OFFSET(port))
-
-#define    RTL8367C_VLAN_PPB_FRAMETYPE_BASE                    RTL8367C_REG_VLAN_PPB0_CTRL2
-#define    RTL8367C_VLAN_PPB_FRAMETYPE_REG(item)               (RTL8367C_VLAN_PPB_FRAMETYPE_BASE + (item << 3))
-#define    RTL8367C_VLAN_PPB_FRAMETYPE_MASK                    RTL8367C_VLAN_PPB0_CTRL2_FRAME_TYPE_MASK
-
-#define    RTL8367C_VLAN_PPB_ETHERTYPR_BASE                        RTL8367C_REG_VLAN_PPB0_CTRL3
-#define    RTL8367C_VLAN_PPB_ETHERTYPR_REG(item)                (RTL8367C_VLAN_PPB_ETHERTYPR_BASE + (item << 3))
-
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION_BASE                RTL8367C_REG_VLAN_MEMBER_CONFIGURATION0_CTRL0
-
-
-#define    RTL8367C_VLAN_CTRL_REG                                RTL8367C_REG_VLAN_CTRL
-
-#define    RTL8367C_VLAN_INGRESS_REG                            RTL8367C_REG_VLAN_INGRESS
-
-#define    RTL8367C_VLAN_ACCEPT_FRAME_TYPE_BASE                    RTL8367C_REG_VLAN_ACCEPT_FRAME_TYPE_CTRL0
-#define    RTL8367C_VLAN_ACCEPT_FRAME_TYPE_REG(port)            (RTL8367C_VLAN_ACCEPT_FRAME_TYPE_BASE + (port >> 3))
-#define    RTL8367C_VLAN_ACCEPT_FRAME_TYPE_MASK(port)           (RTL8367C_PORT0_FRAME_TYPE_MASK << ((port & 0x7) << 1))
-
-#define    RTL8367C_PORT_EFID_BASE                                RTL8367C_REG_PORT_EFID_CTRL0
-#define    RTL8367C_PORT_EFID_REG(port)                            (RTL8367C_PORT_EFID_BASE + (port >> 2))
-#define    RTL8367C_PORT_EFID_OFFSET(port)                         ((port & 0x3) << 2)
-#define    RTL8367C_PORT_EFID_MASK(port)                        (RTL8367C_PORT0_EFID_MASK << RTL8367C_PORT_EFID_OFFSET(port))
-
-#define    RTL8367C_PORT_PBFIDEN_REG                            RTL8367C_REG_PORT_PBFIDEN
-
-#define    RTL8367C_PORT_PBFID_BASE                             RTL8367C_REG_PORT0_PBFID
-#define    RTL8367C_PORT_PBFID_REG(port)                        (RTL8367C_PORT_PBFID_BASE + port)
-
-/* (16'h0800) dpm_reg */
-
-#define    RTL8367C_RMA_CTRL_BASE                                RTL8367C_REG_RMA_CTRL00
-
-
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_BASE                RTL8367C_REG_VLAN_PORTBASED_PRIORITY_CTRL0
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_REG(port)            (RTL8367C_VLAN_PORTBASED_PRIORITY_BASE + (port >> 2))
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_OFFSET(port)        ((port & 0x3) << 2)
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_MASK(port)            (0x7 << RTL8367C_VLAN_PORTBASED_PRIORITY_OFFSET(port))
-
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM_BASE                    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM0_CTRL0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM_REG(port, item)        (RTL8367C_VLAN_PPB_PRIORITY_ITEM_BASE + (item << 2)+ (port>>2))
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM_OFFSET(port)            ((port & 0x3) <<2)
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM_MASK(port)            (RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT0_PRIORITY_MASK << RTL8367C_VLAN_PPB_PRIORITY_ITEM_OFFSET(port))
-
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_BASE                RTL8367C_REG_QOS_1Q_PRIORITY_REMAPPING_CTRL0
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_REG(pri)            (RTL8367C_QOS_1Q_PRIORITY_REMAPPING_BASE + (pri >> 2))
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_OFFSET(pri)        ((pri & 0x3) << 2)
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_MASK(pri)            (0x7 << RTL8367C_QOS_1Q_PRIORITY_REMAPPING_OFFSET(pri))
-
-#define    RTL8367C_QOS_DSCP_TO_PRIORITY_BASE                    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL0
-#define    RTL8367C_QOS_DSCP_TO_PRIORITY_REG(dscp)                (RTL8367C_QOS_DSCP_TO_PRIORITY_BASE + (dscp >> 2))
-#define    RTL8367C_QOS_DSCP_TO_PRIORITY_OFFSET(dscp)            ((dscp & 0x3) << 2)
-#define    RTL8367C_QOS_DSCP_TO_PRIORITY_MASK(dscp)                (0x7 << RTL8367C_QOS_DSCP_TO_PRIORITY_OFFSET(dscp))
-
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_BASE                    RTL8367C_REG_QOS_PORTBASED_PRIORITY_CTRL0
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_REG(port)            (RTL8367C_QOS_PORTBASED_PRIORITY_BASE + (port >> 2))
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_OFFSET(port)            ((port & 0x3) << 2)
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_MASK(port)            (0x7 << RTL8367C_QOS_PORTBASED_PRIORITY_OFFSET(port))
-
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_BASE            RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION_CTRL0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_REG(src)        (RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_BASE + (src >> 1))
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_OFFSET(src)  ((src & 1) << 3)
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_MASK(src)    (RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL0_QOS_PORT_WEIGHT_MASK << RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_OFFSET(src))
-
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_BASE            RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION2_CTRL0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_REG(src)        (RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_BASE + (src >> 1))
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_OFFSET(src)  ((src & 1) << 3)
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_MASK(src)    (RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL0_QOS_PORT_WEIGHT_MASK << RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_OFFSET(src))
-
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_IDX_CTRL            RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION_IDX
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_IDX(port)  (1 << port)
-
-#define    RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_BASE            RTL8367C_REG_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0
-#define    RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_REG(pri)        (RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_BASE + (pri >> 2))
-#define    RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_OFFSET(pri)  ((pri & 0x3) << 2)
-#define    RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_MASK(pri)    (RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY0_MASK << RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_OFFSET(pri))
-
-#define    RTL8367C_QOS_TRAP_PRIORITY_CTRL0_REG                RTL8367C_REG_QOS_TRAP_PRIORITY0
-
-#define    RTL8367C_QOS_TRAP_PRIORITY_CTRL1_REG                RTL8367C_REG_QOS_TRAP_PRIORITY1
-
-#define    RTL8367C_QOS_DSCP_TO_DSCP_BASE                             RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL0
-#define    RTL8367C_QOS_DSCP_TO_DSCP_REG(dscp)                     (RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL0 + (dscp >> 1))
-#define    RTL8367C_QOS_DSCP_TO_DSCP_OFFSET(dscp)                ((dscp & 0x1) << 8)
-#define    RTL8367C_QOS_DSCP_TO_DSCP_MASK(dscp)                   (0x3F << RTL8367C_QOS_DSCP_TO_DSCP_OFFSET(dscp))
-
-#define    RTL8367C_UNUCAST_FLOADING_PMSK_REG                    RTL8367C_REG_UNDA_FLOODING_PMSK
-
-#define    RTL8367C_UNMCAST_FLOADING_PMSK_REG                    RTL8367C_REG_UNMCAST_FLOADING_PMSK
-
-#define    RTL8367C_BCAST_FLOADING_PMSK_REG                        RTL8367C_REG_BCAST_FLOADING_PMSK
-
-#define    RTL8367C_PORT_ISOLATION_PORT_MASK_BASE                RTL8367C_REG_PORT_ISOLATION_PORT0_MASK
-#define    RTL8367C_PORT_ISOLATION_PORT_MASK_REG(port)            (RTL8367C_PORT_ISOLATION_PORT_MASK_BASE + port)
-
-#define    RTL8367C_FORCE_CTRL_REG                                RTL8367C_REG_FORCE_CTRL
-
-#define    RTL8367C_SOURCE_PORT_BLOCK_REG                        RTL8367C_REG_SOURCE_PORT_PERMIT
-
-#define    RTL8367C_IPMCAST_VLAN_LEAKY_REG                        RTL8367C_REG_IPMCAST_VLAN_LEAKY
-
-#define    RTL8367C_IPMCAST_PORTISO_LEAKY_REG                    RTL8367C_REG_IPMCAST_PORTISO_LEAKY
-
-#define    RTL8367C_PORT_SECURIT_CTRL_REG                        RTL8367C_REG_PORT_SECURITY_CTRL
-
-#define    RTL8367C_UNKNOWN_IPV4_MULTICAST_BASE                    RTL8367C_REG_UNKNOWN_IPV4_MULTICAST_CTRL0
-#define    RTL8367C_UNKNOWN_IPV4_MULTICAST_REG(port)            (RTL8367C_UNKNOWN_IPV4_MULTICAST_BASE + (port >> 3))
-#define    RTL8367C_UNKNOWN_IPV4_MULTICAST_OFFSET(port)            ((port & 0x7) << 1)
-#define    RTL8367C_UNKNOWN_IPV4_MULTICAST_MASK(port)            (RTL8367C_PORT0_UNKNOWN_IP4_MCAST_MASK << RTL8367C_UNKNOWN_IPV4_MULTICAST_OFFSET(port))
-
-#define    RTL8367C_UNKNOWN_IPV6_MULTICAST_BASE                    RTL8367C_REG_UNKNOWN_IPV6_MULTICAST_CTRL0
-#define    RTL8367C_UNKNOWN_IPV6_MULTICAST_REG(port)            (RTL8367C_UNKNOWN_IPV6_MULTICAST_BASE + (port >> 3))
-#define    RTL8367C_UNKNOWN_IPV6_MULTICAST_OFFSET(port)            ((port & 0x7) << 1)
-#define    RTL8367C_UNKNOWN_IPV6_MULTICAST_MASK(port)            (RTL8367C_PORT0_UNKNOWN_IP4_MCAST_MASK << RTL8367C_UNKNOWN_IPV6_MULTICAST_OFFSET(port))
-
-#define    RTL8367C_UNKNOWN_L2_MULTICAST_BASE                    RTL8367C_REG_UNKNOWN_L2_MULTICAST_CTRL0
-#define    RTL8367C_UNKNOWN_L2_MULTICAST_REG(port)                (RTL8367C_UNKNOWN_L2_MULTICAST_BASE + (port >> 3))
-#define    RTL8367C_UNKNOWN_L2_MULTICAST_OFFSET(port)            ((port & 0x7) << 1)
-#define    RTL8367C_UNKNOWN_L2_MULTICAST_MASK(port)                (RTL8367C_PORT0_UNKNOWN_L2_MCAST_MASK << RTL8367C_UNKNOWN_L2_MULTICAST_OFFSET(port))
-
-#define    RTL8367C_PORT_TRUNK_CTRL_REG                            RTL8367C_REG_PORT_TRUNK_CTRL
-#define    RTL8367C_PORT_TRUNK_HASH_MASK                           0x007F
-
-#define    RTL8367C_PORT_TRUNK_GROUP_MASK_REG    RTL8367C_REG_PORT_TRUNK_GROUP_MASK
-#define    RTL8367C_PORT_TRUNK_GROUP_MASK_OFFSET(group)    (group << 2)
-#define    RTL8367C_PORT_TRUNK_GROUP_MASK_MASK(group)    (RTL8367C_PORT_TRUNK_GROUP0_MASK_MASK << RTL8367C_PORT_TRUNK_GROUP_MASK_OFFSET(group))
-
-#define    RTL8367C_PORT_TRUNK_FLOWCTRL_REG                        RTL8367C_REG_PORT_TRUNK_FLOWCTRL
-
-#define    RTL8367C_QOS_PORT_QUEUE_NUMBER_BASE                    RTL8367C_REG_QOS_PORT_QUEUE_NUMBER_CTRL0
-#define    RTL8367C_QOS_PORT_QUEUE_NUMBER_REG(port)                (RTL8367C_QOS_PORT_QUEUE_NUMBER_BASE + (port >> 2))
-#define    RTL8367C_QOS_PORT_QUEUE_NUMBER_OFFSET(port)            ((port & 0x3) << 2)
-#define    RTL8367C_QOS_PORT_QUEUE_NUMBER_MASK(port)            (0x7 << RTL8367C_QOS_PORT_QUEUE_NUMBER_OFFSET(port))
-
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_BASE                    RTL8367C_REG_QOS_1Q_PRIORITY_TO_QID_CTRL0
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_REG(index, pri)        (RTL8367C_QOS_1Q_PRIORITY_TO_QID_BASE + (index << 1) + (pri >> 2))
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_OFFSET(pri)            ((pri & 0x3) << 2)
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_MASK(pri)            (RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK << RTL8367C_QOS_1Q_PRIORITY_TO_QID_OFFSET(pri))
-
-#define    RTL8367C_DEBUG_INFO_BASE                                RTL8367C_REG_PORT_DEBUG_INFO_CTRL0
-#define    RTL8367C_DEBUG_INFO_REG(port)                        (RTL8367C_DEBUG_INFO_BASE + (port >>1))
-#define    RTL8367C_DEBUG_INFO_OFFSET(port)                        ((port&1)<<3)
-#define    RTL8367C_DEBUG_INFO_MASK(port)                        (RTL8367C_PORT0_DEBUG_INFO_MASK << RTL8367C_DEBUG_INFO_OFFSET(port))
-
-/* (16'h0a00) l2_reg */
-
-#define    RTL8367C_VLAN_MSTI_BASE                                RTL8367C_REG_VLAN_MSTI0_CTRL0
-#define    RTL8367C_VLAN_MSTI_REG(tree, port)                    (RTL8367C_VLAN_MSTI_BASE + (tree << 1) + (port >> 3))
-#define    RTL8367C_VLAN_MSTI_OFFSET(port)                        ((port & 0x7) << 1)
-#define    RTL8367C_VLAN_MSTI_MASK(port)                        (RTL8367C_VLAN_MSTI0_CTRL0_PORT0_STATE_MASK << RTL8367C_VLAN_MSTI_OFFSET(port))
-
-#define    RTL8367C_LUT_PORT_LEARN_LIMITNO_BASE                    RTL8367C_REG_LUT_PORT0_LEARN_LIMITNO
-#define    RTL8367C_LUT_PORT_LEARN_LIMITNO_REG(port)            (RTL8367C_LUT_PORT_LEARN_LIMITNO_BASE + port)
-
-#define    RTL8367C_LUT_CFG_REG                                    RTL8367C_REG_LUT_CFG
-
-#define    RTL8367C_LUT_AGEOUT_CTRL_REG                            RTL8367C_REG_LUT_AGEOUT_CTRL
-
-#define    RTL8367C_FORCE_FLUSH_REG                                RTL8367C_REG_FORCE_FLUSH
-
-#define    RTL8367C_STORM_BCAST_REG                                RTL8367C_REG_STORM_BCAST
-
-#define    RTL8367C_STORM_MCAST_REG                                RTL8367C_REG_STORM_MCAST
-
-#define    RTL8367C_STORM_UNKNOWN_UCAST_REG                        RTL8367C_REG_STORM_UNKOWN_UCAST
-
-#define    RTL8367C_STORM_UNKNOWN_MCAST_REG                        RTL8367C_REG_STORM_UNKOWN_MCAST
-
-#define    RTL8367C_STORM_BCAST_METER_CTRL_BASE                    RTL8367C_REG_STORM_BCAST_METER_CTRL0
-#define    RTL8367C_STORM_BCAST_METER_CTRL_REG(port)            (RTL8367C_STORM_BCAST_METER_CTRL_BASE + (port >> 1))
-#define    RTL8367C_STORM_BCAST_METER_CTRL_OFFSET(port)            ((port & 0x1) << 3)
-#define    RTL8367C_STORM_BCAST_METER_CTRL_MASK(port)            (0xFF << RTL8367C_STORM_BCAST_METER_CTRL_OFFSET(port))
-
-#define    RTL8367C_STORM_MCAST_METER_CTRL_BASE                    RTL8367C_REG_STORM_MCAST_METER_CTRL0
-#define    RTL8367C_STORM_MCAST_METER_CTRL_REG(port)            (RTL8367C_STORM_MCAST_METER_CTRL_BASE + (port >> 1))
-#define    RTL8367C_STORM_MCAST_METER_CTRL_OFFSET(port)            ((port & 0x1) << 3)
-#define    RTL8367C_STORM_MCAST_METER_CTRL_MASK(port)            (0xFF << RTL8367C_STORM_MCAST_METER_CTRL_OFFSET(port))
-
-#define    RTL8367C_STORM_UNDA_METER_CTRL_BASE                    RTL8367C_REG_STORM_UNDA_METER_CTRL0
-#define    RTL8367C_STORM_UNDA_METER_CTRL_REG(port)                (RTL8367C_STORM_UNDA_METER_CTRL_BASE + (port >> 1))
-#define    RTL8367C_STORM_UNDA_METER_CTRL_OFFSET(port)            ((port & 0x1) << 3)
-#define    RTL8367C_STORM_UNDA_METER_CTRL_MASK(port)            (0xFF << RTL8367C_STORM_UNDA_METER_CTRL_OFFSET(port))
-
-#define    RTL8367C_STORM_UNMC_METER_CTRL_BASE                    RTL8367C_REG_STORM_UNMC_METER_CTRL0
-#define    RTL8367C_STORM_UNMC_METER_CTRL_REG(port)                (RTL8367C_STORM_UNMC_METER_CTRL_BASE + (port >> 1))
-#define    RTL8367C_STORM_UNMC_METER_CTRL_OFFSET(port)            ((port & 0x1) << 3)
-#define    RTL8367C_STORM_UNMC_METER_CTRL_MASK(port)            (0xFF << RTL8367C_STORM_UNMC_METER_CTRL_OFFSET(port))
-
-#define    RTL8367C_OAM_PARSER_OFFSET(port)                        (port*2)
-#define    RTL8367C_OAM_PARSER_MASK(port)                        (RTL8367C_PORT0_PARACT_MASK << RTL8367C_OAM_PARSER_OFFSET(port))
-
-#define    RTL8367C_OAM_MULTIPLEXER_OFFSET(port)                (port*2)
-#define    RTL8367C_OAM_MULTIPLEXER_MASK(port)                    (RTL8367C_PORT0_PARACT_MASK << RTL8367C_OAM_MULTIPLEXER_OFFSET(port))
-
-#define    RTL8367C_OAM_CTRL_REG                                RTL8367C_REG_OAM_CTRL
-
-#define    RTL8367C_DOT1X_PORT_ENABLE_REG                        RTL8367C_REG_DOT1X_PORT_ENABLE
-
-#define    RTL8367C_DOT1X_MAC_ENABLE_REG                        RTL8367C_REG_DOT1X_MAC_ENABLE
-
-#define    RTL8367C_DOT1X_PORT_AUTH_REG                            RTL8367C_REG_DOT1X_PORT_AUTH
-
-#define    RTL8367C_DOT1X_PORT_OPDIR_REG                        RTL8367C_REG_DOT1X_PORT_OPDIR
-
-#define    RTL8367C_DOT1X_UNAUTH_ACT_BASE                        RTL8367C_REG_DOT1X_UNAUTH_ACT_W0
-#define    RTL8367C_DOT1X_UNAUTH_ACT_OFFSET(port)                ((port & 0x7) << 1)
-#define    RTL8367C_DOT1X_UNAUTH_ACT_MASK(port)                    (RTL8367C_DOT1X_PORT0_UNAUTHBH_MASK << RTL8367C_DOT1X_UNAUTH_ACT_OFFSET(port))
-
-#define    RTL8367C_DOT1X_CFG_REG                                RTL8367C_REG_DOT1X_CFG
-
-#define    RTL8367C_REG_L2_LRN_CNT_BASE                            RTL8367C_REG_L2_LRN_CNT_CTRL0
-#define    RTL8367C_REG_L2_LRN_CNT_REG(port)                    (RTL8367C_REG_L2_LRN_CNT_BASE + port)
-
-/* (16'h0b00) mltvlan_reg */
-
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY_BASE_REG(index)        (RTL8367C_REG_SVLAN_MCAST2S_ENTRY0_CTRL0 + index*5)
-
-/* (16'h0c00) svlan_reg */
-
-#define    RTL8367C_SVLAN_MEMBERCFG_BASE_REG(index)                (RTL8367C_REG_SVLAN_MEMBERCFG0_CTRL1 + index*3)
-#define    RTL8367C_SVLAN_C2SCFG_BASE_REG(index)                  (RTL8367C_REG_SVLAN_C2SCFG0_CTRL0+ index*3)
-#define    RTL8367C_SVLAN_CFG_REG                                RTL8367C_REG_SVLAN_CFG
-
-/* (16'h0f00) hsactrl_reg */
-
-#define    RTL8367C_SVLAN_S2C_ENTRY_BASE_REG(index)                (RTL8367C_REG_SVLAN_SP2C_ENTRY0_CTRL0 + index*2)
-
-/* (16'h1000) mib_reg */
-
-#define    RTL8367C_MIB_COUNTER_BASE_REG                        RTL8367C_REG_MIB_COUNTER0
-
-#define    RTL8367C_MIB_ADDRESS_REG                                RTL8367C_REG_MIB_ADDRESS
-
-#define    RTL8367C_MIB_CTRL_REG                                RTL8367C_REG_MIB_CTRL0
-#define    RTL8367C_MIB_PORT07_MASK                                (0xFF<<RTL8367C_PORT0_RESET_OFFSET)
-
-/* (16'h1100) intrpt_reg */
-
-#define    RTL8367C_INTR_CTRL_REG                                RTL8367C_REG_INTR_CTRL
-
-#define    RTL8367C_INTR_IMR_REG                                RTL8367C_REG_INTR_IMR
-
-#define    RTL8367C_INTR_IMS_REG                                RTL8367C_REG_INTR_IMS
-
-#define    RTL8367C_INTR_INDICATOR_BASED                        RTL8367C_REG_LEARN_OVER_INDICATOR
-#define    RTL8367C_LEARN_OVER_INDICATOR_REG                    RTL8367C_REG_LEARN_OVER_INDICATOR
-
-#define    RTL8367C_SPEED_CHANGE_INDICATOR_REG                    RTL8367C_REG_SPEED_CHANGE_INDICATOR
-
-#define    RTL8367C_PORT_LINKDOWN_INDICATOR_REG                    RTL8367C_REG_PORT_LINKDOWN_INDICATOR
-
-#define    RTL8367C_PORT_LINKUP_INDICATOR_REG                    RTL8367C_REG_PORT_LINKUP_INDICATOR
-
-#define    RTL8367C_REG_METER_EXCEED_INDICATOR_BASE                RTL8367C_REG_METER_EXCEED_INDICATOR0
-#define    RTL8367C_REG_METER_EXCEED_INDICATOR_REG(meter)        (RTL8367C_REG_METER_EXCEED_INDICATOR_BASE + (meter >> 4))
-#define    RTL8367C_REG_METER_EXCEED_INDICATOR_OFFSET(meter)    (meter & 0xF)
-
-/* (16'h1200) swcore_reg */
-
-#define    RTL8367C_VS_TPID_REG                                    RTL8367C_REG_VS_TPID
-
-#define    RTL8367C_SWITCH_MAC_BASE                                RTL8367C_REG_SWITCH_MAC0
-
-#define    RTL8367C_REMARKING_CTRL_REG                            RTL8367C_REG_SWITCH_CTRL0
-
-#define    RTL8367C_QOS_DSCP_REMARK_BASE                        RTL8367C_REG_QOS_DSCP_REMARK_CTRL0
-#define    RTL8367C_QOS_DSCP_REMARK_REG(pri)                    (RTL8367C_QOS_DSCP_REMARK_BASE + (pri >> 1))
-#define    RTL8367C_QOS_DSCP_REMARK_OFFSET(pri)                    (((pri) & 0x1) << 3)
-#define    RTL8367C_QOS_DSCP_REMARK_MASK(pri)                    (0x3F << RTL8367C_QOS_DSCP_REMARK_OFFSET(pri))
-
-#define    RTL8367C_QOS_1Q_REMARK_BASE                            RTL8367C_REG_QOS_1Q_REMARK_CTRL0
-#define    RTL8367C_QOS_1Q_REMARK_REG(pri)                        (RTL8367C_QOS_1Q_REMARK_BASE + (pri >> 2))
-#define    RTL8367C_QOS_1Q_REMARK_OFFSET(pri)                    ((pri & 0x3) << 2)
-#define    RTL8367C_QOS_1Q_REMARK_MASK(pri)                        (0x7 << RTL8367C_QOS_1Q_REMARK_OFFSET(pri))
-
-#define    RTL8367C_PTKGEN_PAYLOAD_CTRL0_REG                    RTL8367C_REG_PTKGEN_PAYLOAD_CTRL0
-
-#define    RTL8367C_PTKGEN_PAYLOAD_CTRL1_REG                    RTL8367C_REG_PTKGEN_PAYLOAD_CTRL1
-
-#define    RTL8367C_SVLAN_UPLINK_PORTMASK_REG                    RTL8367C_REG_SVLAN_UPLINK_PORTMASK
-
-#define    RTL8367C_CPU_PORT_MASK_REG                            RTL8367C_REG_CPU_PORT_MASK
-
-#define    RTL8367C_CPU_CTRL_REG                                RTL8367C_REG_CPU_CTRL
-
-#define    RTL8367C_MIRROR_CTRL_REG                                RTL8367C_REG_MIRROR_CTRL
-
-
-#define    RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_BASE            RTL8367C_REG_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL0
-#define    RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG(port)        (RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_BASE + (port >> 1))
-#define    RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG_OFFSET(port)    ((port & 0x1) << 3)
-#define    RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG_MASK(port)    (RTL8367C_PORT0_QUEUE_MASK_MASK << RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG_OFFSET(port))
-
-
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_COUNTER_BASE                RTL8367C_REG_FLOWCTRL_PORT0_PAGE_COUNTER
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_COUNTER_REG(port)        (RTL8367C_FLOWCTRL_PORT_PAGE_COUNTER_BASE + port)
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_COUNTER_MASK                RTL8367C_FLOWCTRL_PORT0_PAGE_COUNTER_MASK
-
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_MAX_BASE                    RTL8367C_REG_FLOWCTRL_PORT0_PAGE_MAX
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_MAX_REG(port)            (RTL8367C_FLOWCTRL_PORT_PAGE_MAX_BASE + port)
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_MAX_MASK                    RTL8367C_FLOWCTRL_PORT0_PAGE_MAX_MASK
-
-#define    RTL8367C_FIELD_SELECTOR_REG(index)                    (RTL8367C_REG_FIELD_SELECTOR0 + index)
-#define    RTL8367C_FIELD_SELECTOR_ENABLE_OFFSET                 RTL8367C_FIELD_SELECTOR0_ENABLE_OFFSET
-#define    RTL8367C_FIELD_SELECTOR_ENABLE_MASK                    RTL8367C_FIELD_SELECTOR0_ENABLE_MASK
-#define    RTL8367C_FIELD_SELECTOR_FORMAT_OFFSET                RTL8367C_FIELD_SELECTOR0_FORMAT_OFFSET
-#define    RTL8367C_FIELD_SELECTOR_FORMAT_MASK                    RTL8367C_FIELD_SELECTOR0_FORMAT_MASK
-#define    RTL8367C_FIELD_SELECTOR_OFFSET_OFFSET                  RTL8367C_FIELD_SELECTOR0_OFFSET_OFFSET
-#define    RTL8367C_FIELD_SELECTOR_OFFSET_MASK                    RTL8367C_FIELD_SELECTOR0_OFFSET_MASK
-
-/* (16'h1300) chip_reg*/
-
-/* (16'h1400) mtrpool_reg */
-#define    RTL8367C_METER_RATE_BASE                                RTL8367C_REG_METER0_RATE_CTRL0
-#define    RTL8367C_METER_RATE_REG(meter)                        ((meter << 1) + RTL8367C_METER_RATE_BASE)
-
-#define    RTL8367C_METER_BUCKET_SIZE_BASE                        RTL8367C_REG_METER0_BUCKET_SIZE
-#define    RTL8367C_METER_BUCKET_SIZE_REG(meter)                (RTL8367C_METER_BUCKET_SIZE_BASE + meter)
-
-#define    RTL8367C_LEAKY_BUCKET_TICK_REG                        RTL8367C_REG_METER_CTRL0
-#define    RTL8367C_LEAKY_BUCKET_TICK_OFFSET                    RTL8367C_METER_TICK_OFFSET
-#define    RTL8367C_LEAKY_BUCKET_TICK_MASK                        RTL8367C_METER_TICK_MASK
-
-#define    RTL8367C_LEAKY_BUCKET_TOKEN_REG                        RTL8367C_REG_METER_CTRL1
-#define    RTL8367C_LEAKY_BUCKET_TOKEN_OFFSET                    RTL8367C_METER_CTRL1_OFFSET
-#define    RTL8367C_LEAKY_BUCKET_TOKEN_MASK                        RTL8367C_METER_CTRL1_MASK
-
-#define    RTL8367C_METER_OVERRATE_INDICATOR_BASE                RTL8367C_REG_METER_OVERRATE_INDICATOR0
-#define    RTL8367C_METER_OVERRATE_INDICATOR_REG(meter)            (RTL8367C_METER_OVERRATE_INDICATOR_BASE + (meter >> 4))
-#define    RTL8367C_METER_EXCEED_OFFSET(meter)                    (meter & 0xF)
-#define    RTL8367C_METER_EXCEED_MASK(meter)                    (1 << RTL8367C_METER_EXCEED_OFFSET(meter))
-
-#define    RTL8367C_METER_IFG_CTRL_BASE                            RTL8367C_REG_METER_IFG_CTRL0
-#define    RTL8367C_METER_IFG_CTRL_REG(meter)                    (RTL8367C_METER_IFG_CTRL_BASE + (meter >> 4))
-#define    RTL8367C_METER_IFG_OFFSET(meter)                        (meter & 0xF)
-#define    RTL8367C_METER_IFG_MASK(meter)                        (1 << RTL8367C_METER_IFG_OFFSET(meter))
-
-#define    RTL8367C_FLOWCTRL_CTRL_REG                            RTL8367C_REG_FLOWCTRL_CTRL0
-
-/* (16'h1800)8051_RLDP_EEE_reg */
-#define    RTL8367C_EEELLDP_CTRL0_REG                            RTL8367C_REG_EEELLDP_CTRL0
-
-#define    RTL8367C_EEELLDP_CTRL1_REG                            RTL8367C_REG_EEELLDP_CTRL1
-
-#define    RTL8367C_EEELLDP_PMSK_REG                            RTL8367C_REG_EEELLDP_PMSK
-
-#define    RTL8367C_EEELLDP_TX_FRAMEU_REG_BASE                    RTL8367C_REG_EEELLDP_FRAMEU00
-
-#define    RTL8367C_EEELLDP_TX_CAP_FRAMEL_REG_BASE                RTL8367C_REG_EEELLDP_CAP_FRAMEL00
-
-#define    RTL8367C_EEELLDP_RX_VALUE_PORT_BASE                    RTL8367C_REG_EEELLDP_RX_VALUE_P00_00
-#define    RTL8367C_EEELLDP_RX_VALUE_PORT_REG(port)                (RTL8367C_EEELLDP_RX_VALUE_PORT_BASE + (port * 9))
-
-#define    RTL8367C_RLDP_CTRL0_REG                                RTL8367C_REG_RLDP_CTRL0
-#define    RTL8367C_RLDP_MODE_OFFSET    14
-
-#define    RTL8367C_RLDP_RETRY_COUNT_REG                        RTL8367C_REG_RLDP_CTRL1
-
-#define    RTL8367C_RLDP_RETRY_PERIOD_LOOPSTATE_REG                RTL8367C_REG_RLDP_CTRL2
-
-#define    RTL8367C_RLDP_RETRY_PERIOD_CHKSTATE_REG                RTL8367C_REG_RLDP_CTRL3
-
-#define    RTL8367C_RLDP_TX_PMSK_REG                            RTL8367C_REG_RLDP_CTRL4
-
-#define    RTL8367C_RLDP_RAND_NUM_REG_BASE                        RTL8367C_REG_RLDP_RAND_NUM0
-
-#define    RTL8367C_RLDP_MAGIC_NUM_REG_BASE                        RTL8367C_REG_RLDP_MAGIC_NUM0
-
-#define    RTL8367C_RLDP_LOOP_PMSK_REG                            RTL8367C_REG_RLDP_LOOPSTATUS_INDICATOR
-
-#define    RTL8367C_RLDP_LOOP_PORT_BASE                            RTL8367C_REG_RLDP_LOOP_PORT_REG0
-#define    RTL8367C_RLDP_LOOP_PORT_REG(port)                    (RTL8367C_RLDP_LOOP_PORT_BASE + (port >> 1))
-#define    RTL8367C_RLDP_LOOP_PORT_OFFSET(port)                    ((port & 0x1) << 3)
-#define    RTL8367C_RLDP_LOOP_PORT_MASK(port)                    (RTL8367C_RLDP_LOOP_PORT_00_MASK << RTL8367C_RLDP_LOOP_PORT_OFFSET(port))
-
-#define    RTL8367C_PAGEMETER_PORT_BASE                            RTL8367C_REG_PAGEMETER_PORT0_CTRL0
-#define    RTL8367C_PAGEMETER_PORT_REG(port)                    (RTL8367C_PAGEMETER_PORT_BASE + 0x20*port)
-
-#define    RTL8367C_HIGHPRI_INDICATOR_REG                        RTL8367C_REG_HIGHPRI_INDICATOR
-#define    RTL8367C_PORT_INDICATOR_OFFSET(port)                    (port)
-#define    RTL8367C_PORT_INDICATOR_MASK(port)                    (RTL8367C_PORT0_INDICATOR_MASK << RTL8367C_PORT_INDICATOR_OFFSET(port))
-
-#define    RTL8367C_HIGHPRI_CFG_REG                                RTL8367C_REG_HIGHPRI_CFG
-
-#define    RTL8367C_EAV_PRIORITY_REMAPPING_BASE                    RTL8367C_REG_EAV_CTRL1
-#define    RTL8367C_EAV_PRIORITY_REMAPPING_REG(pri)                (RTL8367C_EAV_PRIORITY_REMAPPING_BASE + (pri >> 2))
-#define    RTL8367C_EAV_PRIORITY_REMAPPING_OFFSET(pri)            ((pri & 0x3) * RTL8367C_REMAP_EAV_PRI1_REGEN_OFFSET)
-#define    RTL8367C_EAV_PRIORITY_REMAPPING_MASK(pri)            (RTL8367C_REMAP_EAV_PRI0_REGEN_MASK << RTL8367C_EAV_PRIORITY_REMAPPING_OFFSET(pri))
-
-#define    RTL8367C_EEEP_CFG_BASE                                RTL8367C_REG_PORT0_EEECFG
-#define    RTL8367C_EEEP_CFG_REG(port)                            (RTL8367C_EEEP_CFG_BASE + (port*0x20))
-
-#define    RTL8367C_PKG_CFG_BASE                                RTL8367C_REG_PKTGEN_PORT0_CTRL
-#define    RTL8367C_PKG_CFG_REG(port)                            (RTL8367C_PKG_CFG_BASE + (port*0x20))
-
-#define    RTL8367C_PKG_DA_BASE                                    RTL8367C_REG_PKTGEN_PORT0_DA0
-#define    RTL8367C_PKG_DA_REG(port)                            (RTL8367C_PKG_DA_BASE + (port*0x20))
-
-#define    RTL8367C_PKG_SA_BASE                                    RTL8367C_REG_PKTGEN_PORT0_SA0
-#define    RTL8367C_PKG_SA_REG(port)                            (RTL8367C_PKG_SA_BASE + (port*0x20))
-
-#define    RTL8367C_PKG_NUM_BASE                                RTL8367C_REG_PKTGEN_PORT0_COUNTER0
-#define    RTL8367C_PKG_NUM_REG(port)                            (RTL8367C_PKG_NUM_BASE + (port*0x20))
-
-#define    RTL8367C_PKG_LENGTH_BASE                                RTL8367C_REG_PKTGEN_PORT0_TX_LENGTH
-#define    RTL8367C_PKG_LENGTH_REG(port)                        (RTL8367C_PKG_LENGTH_BASE + (port*0x20))
-
-/* (16'h1c00)IGMP_MLD_reg */
-#define    RTL8367C_IGMP_GROUP_USAGE_BASE                       RTL8367C_REG_IGMP_GROUP_USAGE_LIST0
-#define    RTL8367C_IGMP_GROUP_USAGE_REG(idx)                   (RTL8367C_IGMP_GROUP_USAGE_BASE + (idx / 16))
-
-#define    RTL8367C_FALLBACK_BASE                               RTL8367C_REG_FALLBACK_PORT0_CFG0
-#define    RTL8367C_FALLBACK_PORT_CFG_REG(port)                 (RTL8367C_FALLBACK_BASE + (port * 4))
-#define    RTL8367C_FALLBACK_PORT_MON_CNT_REG(port)             (RTL8367C_FALLBACK_BASE + 1 + (port * 4))
-#define    RTL8367C_FALLBACK_PORT_ERR_CNT_REG(port)             (RTL8367C_FALLBACK_BASE + 3 + (port * 4))
-
-
-/* (16'h6400)timer_1588 */
-#define    RTL8367C_EAV_CFG_BASE                                              RTL8367C_REG_P0_EAV_CFG
-#define    RTL8367C_EAV_PORT_CFG_REG(port)                              (RTL8367C_EAV_CFG_BASE + (port *0x10))
-#define    RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET                 RTL8367C_P0_EAV_CFG_PTP_PHY_EN_EN_OFFSET
-#define    RTL8367C_EAV_CFG_RX_PDELAY_RESP_OFFSET                RTL8367C_P0_EAV_CFG_RX_PDELAY_RESP_OFFSET
-#define    RTL8367C_EAV_CFG_RX_PDELAY_REQ_OFFSET                 RTL8367C_P0_EAV_CFG_RX_PDELAY_REQ_OFFSET
-#define    RTL8367C_EAV_CFG_RX_DELAY_REQ_OFFSET                   RTL8367C_P0_EAV_CFG_RX_DELAY_REQ_OFFSET
-#define    RTL8367C_EAV_CFG_RX_SYNC_OFFSET                            RTL8367C_P0_EAV_CFG_RX_SYNC_OFFSET
-#define    RTL8367C_EAV_CFG_TX_PDELAY_RESP_OFFSET                RTL8367C_P0_EAV_CFG_TX_PDELAY_RESP_OFFSET
-#define    RTL8367C_EAV_CFG_TX_PDELAY_REQ_OFFSET                 RTL8367C_P0_EAV_CFG_TX_PDELAY_REQ_OFFSET
-#define    RTL8367C_EAV_CFG_TX_DELAY_REQ_OFFSET                   RTL8367C_P0_EAV_CFG_TX_DELAY_REQ_OFFSET
-#define    RTL8367C_EAV_CFG_TX_SYNC_OFFSET                            RTL8367C_P0_EAV_CFG_TX_SYNC_OFFSET
-
-#define    RTL8367C_REG_TX_SYNC_SEQ_ID_BASE                       RTL8367C_REG_P0_TX_SYNC_SEQ_ID
-#define    RTL8367C_REG_TX_SYNC_SEQ_ID(port)                        (RTL8367C_REG_TX_SYNC_SEQ_ID_BASE + (port *0x10))
-#define    RTL8367C_REG_SEQ_ID(port, type)                              (RTL8367C_REG_TX_SYNC_SEQ_ID_BASE + type + (port *0x10))
-
-#define    RTL8367C_REG_TX_DELAY_REQ_SEQ_ID_BASE              RTL8367C_REG_P0_TX_DELAY_REQ_SEQ_ID
-#define    RTL8367C_REG_TX_PDELAY_REQ_SEQ_ID_BASE          RTL8367C_REG_P0_TX_PDELAY_REQ_SEQ_ID
-#define    RTL8367C_REG_TX_PDELAY_RESP_SEQ_ID_BASE        RTL8367C_REG_P0_TX_PDELAY_RESP_SEQ_ID
-#define    RTL8367C_REG_RX_SYNC_SEQ_ID_BASE                        RTL8367C_REG_P0_RX_SYNC_SEQ_ID
-#define    RTL8367C_REG_RX_DELAY_REQ_SEQ_ID_BASE            RTL8367C_REG_P0_RX_DELAY_REQ_SEQ_ID
-#define    RTL8367C_REG_RX_PDELAY_REQ_SEQ_ID_BASE        RTL8367C_REG_P0_RX_PDELAY_REQ_SEQ_ID
-#define    RTL8367C_REG_RX_PDELAY_RESP_SEQ_ID_BASE        RTL8367C_REG_P0_RX_PDELAY_RESP_SEQ_ID
-
-#define    RTL8367C_REG_PORT_NSEC_L_BASE                            RTL8367C_REG_P0_PORT_NSEC_15_0
-#define    RTL8367C_REG_PORT_NSEC_L(port)                            (RTL8367C_REG_PORT_NSEC_L_BASE + (port *0x10))
-#define    RTL8367C_REG_PORT_NSEC_H_BASE                            RTL8367C_REG_P0_PORT_NSEC_26_16
-#define    RTL8367C_REG_PORT_NSEC_H(port)                            (RTL8367C_REG_PORT_NSEC_H_BASE + (port *0x10))
-#define    RTL8367C_PORT_NSEC_H_OFFSET                                RTL8367C_P0_PORT_NSEC_26_16_OFFSET
-#define    RTL8367C_PORT_NSEC_H_MASK                                   RTL8367C_P0_PORT_NSEC_26_16_MASK
-
-#define    RTL8367C_REG_PORT_SEC_L_BASE                                RTL8367C_REG_P0_PORT_SEC_15_0
-#define    RTL8367C_REG_PORT_SEC_L(port)                            (RTL8367C_REG_PORT_SEC_L_BASE + (port *0x10))
-#define    RTL8367C_REG_PORT_SEC_H_BASE                            RTL8367C_REG_P0_PORT_SEC_31_16
-#define    RTL8367C_REG_PORT_SEC_H(port)                            (RTL8367C_REG_PORT_SEC_H_BASE + (port *0x10))
-
-#endif /*#ifndef _RTL8367C_BASE_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_reg.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_reg.h
deleted file mode 100644
index eb4f48b83e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/rtl8367c_reg.h
+++ /dev/null
@@ -1,22819 +0,0 @@
-#ifndef _RTL8367C_REG_H_
-#define _RTL8367C_REG_H_
-
-/************************************************************
-auto-generated register address and field data
-*************************************************************/
-
-/* (16'h0000)port_reg */
-
-#define    RTL8367C_REG_PORT0_CGST_HALF_CFG    0x0000
-#define    RTL8367C_PORT0_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT0_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT0_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT0_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT0_CTRL    0x0001
-#define    RTL8367C_PKTGEN_PORT0_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT0_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT0_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT0_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT0_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT0_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT0_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT0_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT0    0x0002
-#define    RTL8367C_TX_ERR_CNT_PORT0_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT0_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT0_DA0    0x0003
-
-#define    RTL8367C_REG_PKTGEN_PORT0_DA1    0x0004
-
-#define    RTL8367C_REG_PKTGEN_PORT0_DA2    0x0005
-
-#define    RTL8367C_REG_PKTGEN_PORT0_SA0    0x0006
-
-#define    RTL8367C_REG_PKTGEN_PORT0_SA1    0x0007
-
-#define    RTL8367C_REG_PKTGEN_PORT0_SA2    0x0008
-
-#define    RTL8367C_REG_PKTGEN_PORT0_COUNTER0    0x0009
-
-#define    RTL8367C_REG_PKTGEN_PORT0_COUNTER1    0x000a
-#define    RTL8367C_PKTGEN_PORT0_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT0_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT0_TX_LENGTH    0x000b
-#define    RTL8367C_PKTGEN_PORT0_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT0_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT0_TIMER    0x000d
-#define    RTL8367C_PKTGEN_PORT0_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT0_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT0_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT0_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT0_MISC_CFG    0x000e
-#define    RTL8367C_PORT0_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT0_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT0_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT0_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT0_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT0_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT0_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT0_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT0_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT0_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT0_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT0_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT0_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT0_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT0_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT0_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT0_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT0_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT0_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT0_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT0_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT0_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT0_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT0_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT0_RATE_CTRL0    0x000f
-
-#define    RTL8367C_REG_INGRESSBW_PORT0_RATE_CTRL1    0x0010
-#define    RTL8367C_INGRESSBW_PORT0_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT0_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT0_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT0_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT0_FORCE_RATE0    0x0011
-
-#define    RTL8367C_REG_PORT0_FORCE_RATE1    0x0012
-
-#define    RTL8367C_REG_PORT0_CURENT_RATE0    0x0013
-
-#define    RTL8367C_REG_PORT0_CURENT_RATE1    0x0014
-
-#define    RTL8367C_REG_PORT0_PAGE_COUNTER    0x0015
-#define    RTL8367C_PORT0_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT0_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT0_CTRL0    0x0016
-
-#define    RTL8367C_REG_PAGEMETER_PORT0_CTRL1    0x0017
-
-#define    RTL8367C_REG_PORT0_EEECFG    0x0018
-#define    RTL8367C_PORT0_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT0_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT0_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT0_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT0_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT0_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT0_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT0_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT0_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT0_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT0_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT0_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT0_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT0_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT0_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT0_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT0_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT0_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT0_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT0_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT0_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT0_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT0_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT0_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT0_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT0_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT0_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT0_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT0_EEETXMTR    0x0019
-
-#define    RTL8367C_REG_PORT0_EEERXMTR    0x001a
-
-#define    RTL8367C_REG_PORT0_EEEPTXMTR    0x001b
-
-#define    RTL8367C_REG_PORT0_EEEPRXMTR    0x001c
-
-#define    RTL8367C_REG_PTP_PORT0_CFG1    0x001e
-#define    RTL8367C_PTP_PORT0_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT0_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P0_MSIC1    0x001f
-#define    RTL8367C_P0_MSIC1_OFFSET    0
-#define    RTL8367C_P0_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT1_CGST_HALF_CFG    0x0020
-#define    RTL8367C_PORT1_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT1_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT1_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT1_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT1_CTRL    0x0021
-#define    RTL8367C_PKTGEN_PORT1_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT1_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT1_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT1_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT1_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT1_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT1_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT1_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT1    0x0022
-#define    RTL8367C_TX_ERR_CNT_PORT1_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT1_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT1_DA0    0x0023
-
-#define    RTL8367C_REG_PKTGEN_PORT1_DA1    0x0024
-
-#define    RTL8367C_REG_PKTGEN_PORT1_DA2    0x0025
-
-#define    RTL8367C_REG_PKTGEN_PORT1_SA0    0x0026
-
-#define    RTL8367C_REG_PKTGEN_PORT1_SA1    0x0027
-
-#define    RTL8367C_REG_PKTGEN_PORT1_SA2    0x0028
-
-#define    RTL8367C_REG_PKTGEN_PORT1_COUNTER0    0x0029
-
-#define    RTL8367C_REG_PKTGEN_PORT1_COUNTER1    0x002a
-#define    RTL8367C_PKTGEN_PORT1_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT1_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT1_TX_LENGTH    0x002b
-#define    RTL8367C_PKTGEN_PORT1_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT1_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT1_TIMER    0x002d
-#define    RTL8367C_PKTGEN_PORT1_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT1_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT1_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT1_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT1_MISC_CFG    0x002e
-#define    RTL8367C_PORT1_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT1_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT1_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT1_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT1_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT1_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT1_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT1_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT1_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT1_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT1_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT1_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT1_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT1_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT1_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT1_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT1_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT1_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT1_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT1_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT1_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT1_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT1_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT1_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT1_RATE_CTRL0    0x002f
-
-#define    RTL8367C_REG_INGRESSBW_PORT1_RATE_CTRL1    0x0030
-#define    RTL8367C_INGRESSBW_PORT1_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT1_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT1_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT1_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT1_FORCE_RATE0    0x0031
-
-#define    RTL8367C_REG_PORT1_FORCE_RATE1    0x0032
-
-#define    RTL8367C_REG_PORT1_CURENT_RATE0    0x0033
-
-#define    RTL8367C_REG_PORT1_CURENT_RATE1    0x0034
-
-#define    RTL8367C_REG_PORT1_PAGE_COUNTER    0x0035
-#define    RTL8367C_PORT1_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT1_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT1_CTRL0    0x0036
-
-#define    RTL8367C_REG_PAGEMETER_PORT1_CTRL1    0x0037
-
-#define    RTL8367C_REG_PORT1_EEECFG    0x0038
-#define    RTL8367C_PORT1_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT1_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT1_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT1_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT1_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT1_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT1_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT1_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT1_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT1_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT1_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT1_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT1_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT1_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT1_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT1_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT1_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT1_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT1_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT1_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT1_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT1_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT1_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT1_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT1_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT1_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT1_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT1_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT1_EEETXMTR    0x0039
-
-#define    RTL8367C_REG_PORT1_EEERXMTR    0x003a
-
-#define    RTL8367C_REG_PORT1_EEEPTXMTR    0x003b
-
-#define    RTL8367C_REG_PORT1_EEEPRXMTR    0x003c
-
-#define    RTL8367C_REG_PTP_PORT1_CFG1    0x003e
-#define    RTL8367C_PTP_PORT1_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT1_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P1_MSIC1    0x003f
-#define    RTL8367C_P1_MSIC1_OFFSET    0
-#define    RTL8367C_P1_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT2_CGST_HALF_CFG    0x0040
-#define    RTL8367C_PORT2_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT2_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT2_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT2_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT2_CTRL    0x0041
-#define    RTL8367C_PKTGEN_PORT2_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT2_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT2_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT2_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT2_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT2_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT2_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT2_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT2    0x0042
-#define    RTL8367C_TX_ERR_CNT_PORT2_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT2_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT2_DA0    0x0043
-
-#define    RTL8367C_REG_PKTGEN_PORT2_DA1    0x0044
-
-#define    RTL8367C_REG_PKTGEN_PORT2_DA2    0x0045
-
-#define    RTL8367C_REG_PKTGEN_PORT2_SA0    0x0046
-
-#define    RTL8367C_REG_PKTGEN_PORT2_SA1    0x0047
-
-#define    RTL8367C_REG_PKTGEN_PORT2_SA2    0x0048
-
-#define    RTL8367C_REG_PKTGEN_PORT2_COUNTER0    0x0049
-
-#define    RTL8367C_REG_PKTGEN_PORT2_COUNTER1    0x004a
-#define    RTL8367C_PKTGEN_PORT2_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT2_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT2_TX_LENGTH    0x004b
-#define    RTL8367C_PKTGEN_PORT2_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT2_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT2_TIMER    0x004d
-#define    RTL8367C_PKTGEN_PORT2_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT2_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT2_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT2_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT2_MISC_CFG    0x004e
-#define    RTL8367C_PORT2_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT2_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT2_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT2_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT2_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT2_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT2_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT2_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT2_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT2_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT2_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT2_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT2_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT2_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT2_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT2_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT2_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT2_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT2_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT2_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT2_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT2_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT2_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT2_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT2_RATE_CTRL0    0x004f
-
-#define    RTL8367C_REG_INGRESSBW_PORT2_RATE_CTRL1    0x0050
-#define    RTL8367C_INGRESSBW_PORT2_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT2_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT2_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT2_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT2_FORCE_RATE0    0x0051
-
-#define    RTL8367C_REG_PORT2_FORCE_RATE1    0x0052
-
-#define    RTL8367C_REG_PORT2_CURENT_RATE0    0x0053
-
-#define    RTL8367C_REG_PORT2_CURENT_RATE1    0x0054
-
-#define    RTL8367C_REG_PORT2_PAGE_COUNTER    0x0055
-#define    RTL8367C_PORT2_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT2_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT2_CTRL0    0x0056
-
-#define    RTL8367C_REG_PAGEMETER_PORT2_CTRL1    0x0057
-
-#define    RTL8367C_REG_PORT2_EEECFG    0x0058
-#define    RTL8367C_PORT2_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT2_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT2_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT2_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT2_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT2_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT2_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT2_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT2_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT2_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT2_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT2_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT2_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT2_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT2_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT2_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT2_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT2_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT2_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT2_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT2_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT2_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT2_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT2_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT2_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT2_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT2_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT2_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT2_EEETXMTR    0x0059
-
-#define    RTL8367C_REG_PORT2_EEERXMTR    0x005a
-
-#define    RTL8367C_REG_PORT2_EEEPTXMTR    0x005b
-
-#define    RTL8367C_REG_PORT2_EEEPRXMTR    0x005c
-
-#define    RTL8367C_REG_PTP_PORT2_CFG1    0x005e
-#define    RTL8367C_PTP_PORT2_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT2_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P2_MSIC1    0x005f
-#define    RTL8367C_P2_MSIC1_OFFSET    0
-#define    RTL8367C_P2_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT3_CGST_HALF_CFG    0x0060
-#define    RTL8367C_PORT3_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT3_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT3_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT3_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT3_CTRL    0x0061
-#define    RTL8367C_PKTGEN_PORT3_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT3_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT3_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT3_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT3_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT3_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT3_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT3_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT3    0x0062
-#define    RTL8367C_TX_ERR_CNT_PORT3_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT3_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT3_DA0    0x0063
-
-#define    RTL8367C_REG_PKTGEN_PORT3_DA1    0x0064
-
-#define    RTL8367C_REG_PKTGEN_PORT3_DA2    0x0065
-
-#define    RTL8367C_REG_PKTGEN_PORT3_SA0    0x0066
-
-#define    RTL8367C_REG_PKTGEN_PORT3_SA1    0x0067
-
-#define    RTL8367C_REG_PKTGEN_PORT3_SA2    0x0068
-
-#define    RTL8367C_REG_PKTGEN_PORT3_COUNTER0    0x0069
-
-#define    RTL8367C_REG_PKTGEN_PORT3_COUNTER1    0x006a
-#define    RTL8367C_PKTGEN_PORT3_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT3_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT3_TX_LENGTH    0x006b
-#define    RTL8367C_PKTGEN_PORT3_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT3_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT3_TIMER    0x006d
-#define    RTL8367C_PKTGEN_PORT3_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT3_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT3_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT3_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT3_MISC_CFG    0x006e
-#define    RTL8367C_PORT3_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT3_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT3_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT3_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT3_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT3_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT3_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT3_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT3_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT3_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT3_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT3_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT3_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT3_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT3_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT3_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT3_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT3_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT3_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT3_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT3_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT3_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT3_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT3_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT3_RATE_CTRL0    0x006f
-
-#define    RTL8367C_REG_INGRESSBW_PORT3_RATE_CTRL1    0x0070
-#define    RTL8367C_INGRESSBW_PORT3_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT3_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT3_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT3_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT3_FORCE_RATE0    0x0071
-
-#define    RTL8367C_REG_PORT3_FORCE_RATE1    0x0072
-
-#define    RTL8367C_REG_PORT3_CURENT_RATE0    0x0073
-
-#define    RTL8367C_REG_PORT3_CURENT_RATE1    0x0074
-
-#define    RTL8367C_REG_PORT3_PAGE_COUNTER    0x0075
-#define    RTL8367C_PORT3_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT3_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT3_CTRL0    0x0076
-
-#define    RTL8367C_REG_PAGEMETER_PORT3_CTRL1    0x0077
-
-#define    RTL8367C_REG_PORT3_EEECFG    0x0078
-#define    RTL8367C_PORT3_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT3_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT3_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT3_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT3_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT3_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT3_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT3_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT3_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT3_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT3_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT3_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT3_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT3_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT3_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT3_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT3_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT3_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT3_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT3_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT3_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT3_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT3_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT3_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT3_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT3_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT3_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT3_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT3_EEETXMTR    0x0079
-
-#define    RTL8367C_REG_PORT3_EEERXMTR    0x007a
-
-#define    RTL8367C_REG_PORT3_EEEPTXMTR    0x007b
-
-#define    RTL8367C_REG_PORT3_EEEPRXMTR    0x007c
-
-#define    RTL8367C_REG_PTP_PORT3_CFG1    0x007e
-#define    RTL8367C_PTP_PORT3_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT3_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P3_MSIC1    0x007f
-#define    RTL8367C_P3_MSIC1_OFFSET    0
-#define    RTL8367C_P3_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT4_CGST_HALF_CFG    0x0080
-#define    RTL8367C_PORT4_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT4_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT4_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT4_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT4_CTRL    0x0081
-#define    RTL8367C_PKTGEN_PORT4_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT4_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT4_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT4_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT4_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT4_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT4_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT4_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT4    0x0082
-#define    RTL8367C_TX_ERR_CNT_PORT4_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT4_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT4_DA0    0x0083
-
-#define    RTL8367C_REG_PKTGEN_PORT4_DA1    0x0084
-
-#define    RTL8367C_REG_PKTGEN_PORT4_DA2    0x0085
-
-#define    RTL8367C_REG_PKTGEN_PORT4_SA0    0x0086
-
-#define    RTL8367C_REG_PKTGEN_PORT4_SA1    0x0087
-
-#define    RTL8367C_REG_PKTGEN_PORT4_SA2    0x0088
-
-#define    RTL8367C_REG_PKTGEN_PORT4_COUNTER0    0x0089
-
-#define    RTL8367C_REG_PKTGEN_PORT4_COUNTER1    0x008a
-#define    RTL8367C_PKTGEN_PORT4_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT4_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT4_TX_LENGTH    0x008b
-#define    RTL8367C_PKTGEN_PORT4_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT4_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT4_TIMER    0x008d
-#define    RTL8367C_PKTGEN_PORT4_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT4_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT4_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT4_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT4_MISC_CFG    0x008e
-#define    RTL8367C_PORT4_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT4_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT4_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT4_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT4_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT4_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT4_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT4_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT4_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT4_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT4_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT4_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT4_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT4_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT4_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT4_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT4_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT4_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT4_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT4_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT4_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT4_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT4_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT4_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT4_RATE_CTRL0    0x008f
-
-#define    RTL8367C_REG_INGRESSBW_PORT4_RATE_CTRL1    0x0090
-#define    RTL8367C_INGRESSBW_PORT4_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT4_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT4_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT4_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT4_FORCE_RATE0    0x0091
-
-#define    RTL8367C_REG_PORT4_FORCE_RATE1    0x0092
-
-#define    RTL8367C_REG_PORT4_CURENT_RATE0    0x0093
-
-#define    RTL8367C_REG_PORT4_CURENT_RATE1    0x0094
-
-#define    RTL8367C_REG_PORT4_PAGE_COUNTER    0x0095
-#define    RTL8367C_PORT4_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT4_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT4_CTRL0    0x0096
-
-#define    RTL8367C_REG_PAGEMETER_PORT4_CTRL1    0x0097
-
-#define    RTL8367C_REG_PORT4_EEECFG    0x0098
-#define    RTL8367C_PORT4_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT4_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT4_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT4_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT4_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT4_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT4_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT4_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT4_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT4_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT4_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT4_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT4_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT4_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT4_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT4_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT4_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT4_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT4_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT4_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT4_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT4_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT4_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT4_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT4_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT4_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT4_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT4_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT4_EEETXMTR    0x0099
-
-#define    RTL8367C_REG_PORT4_EEERXMTR    0x009a
-
-#define    RTL8367C_REG_PORT4_EEEPTXMTR    0x009b
-
-#define    RTL8367C_REG_PORT4_EEEPRXMTR    0x009c
-
-#define    RTL8367C_REG_PTP_PORT4_CFG1    0x009e
-#define    RTL8367C_PTP_PORT4_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT4_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P4_MSIC1    0x009f
-#define    RTL8367C_P4_MSIC1_OFFSET    0
-#define    RTL8367C_P4_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT5_CGST_HALF_CFG    0x00a0
-#define    RTL8367C_PORT5_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT5_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT5_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT5_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT5_CTRL    0x00a1
-#define    RTL8367C_PKTGEN_PORT5_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT5_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT5_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT5_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT5_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT5_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT5_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT5_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT5    0x00a2
-#define    RTL8367C_TX_ERR_CNT_PORT5_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT5_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT5_DA0    0x00a3
-
-#define    RTL8367C_REG_PKTGEN_PORT5_DA1    0x00a4
-
-#define    RTL8367C_REG_PKTGEN_PORT5_DA2    0x00a5
-
-#define    RTL8367C_REG_PKTGEN_PORT5_SA0    0x00a6
-
-#define    RTL8367C_REG_PKTGEN_PORT5_SA1    0x00a7
-
-#define    RTL8367C_REG_PKTGEN_PORT5_SA2    0x00a8
-
-#define    RTL8367C_REG_PKTGEN_PORT5_COUNTER0    0x00a9
-
-#define    RTL8367C_REG_PKTGEN_PORT5_COUNTER1    0x00aa
-#define    RTL8367C_PKTGEN_PORT5_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT5_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT5_TX_LENGTH    0x00ab
-#define    RTL8367C_PKTGEN_PORT5_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT5_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT5_TIMER    0x00ad
-#define    RTL8367C_PKTGEN_PORT5_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT5_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT5_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT5_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT5_MISC_CFG    0x00ae
-#define    RTL8367C_PORT5_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT5_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT5_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT5_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT5_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT5_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT5_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT5_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT5_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT5_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT5_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT5_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT5_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT5_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT5_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT5_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT5_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT5_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT5_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT5_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT5_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT5_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT5_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT5_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT5_RATE_CTRL0    0x00af
-
-#define    RTL8367C_REG_INGRESSBW_PORT5_RATE_CTRL1    0x00b0
-#define    RTL8367C_INGRESSBW_PORT5_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT5_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT5_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT5_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT5_FORCE_RATE0    0x00b1
-
-#define    RTL8367C_REG_PORT5_FORCE_RATE1    0x00b2
-
-#define    RTL8367C_REG_PORT5_CURENT_RATE0    0x00b3
-
-#define    RTL8367C_REG_PORT5_CURENT_RATE1    0x00b4
-
-#define    RTL8367C_REG_PORT5_PAGE_COUNTER    0x00b5
-#define    RTL8367C_PORT5_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT5_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT5_CTRL0    0x00b6
-
-#define    RTL8367C_REG_PAGEMETER_PORT5_CTRL1    0x00b7
-
-#define    RTL8367C_REG_PORT5_EEECFG    0x00b8
-#define    RTL8367C_PORT5_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT5_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT5_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT5_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT5_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT5_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT5_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT5_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT5_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT5_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT5_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT5_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT5_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT5_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT5_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT5_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT5_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT5_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT5_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT5_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT5_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT5_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT5_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT5_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT5_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT5_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT5_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT5_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT5_EEETXMTR    0x00b9
-
-#define    RTL8367C_REG_PORT5_EEERXMTR    0x00ba
-
-#define    RTL8367C_REG_PORT5_EEEPTXMTR    0x00bb
-
-#define    RTL8367C_REG_PORT5_EEEPRXMTR    0x00bc
-
-#define    RTL8367C_REG_PTP_PORT5_CFG1    0x00be
-#define    RTL8367C_PTP_PORT5_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT5_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P5_MSIC1    0x00bf
-#define    RTL8367C_P5_MSIC1_OFFSET    0
-#define    RTL8367C_P5_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT6_CGST_HALF_CFG    0x00c0
-#define    RTL8367C_PORT6_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT6_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT6_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT6_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT6_CTRL    0x00c1
-#define    RTL8367C_PKTGEN_PORT6_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT6_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT6_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT6_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT6_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT6_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT6_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT6_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT6    0x00c2
-#define    RTL8367C_TX_ERR_CNT_PORT6_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT6_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT6_DA0    0x00c3
-
-#define    RTL8367C_REG_PKTGEN_PORT6_DA1    0x00c4
-
-#define    RTL8367C_REG_PKTGEN_PORT6_DA2    0x00c5
-
-#define    RTL8367C_REG_PKTGEN_PORT6_SA0    0x00c6
-
-#define    RTL8367C_REG_PKTGEN_PORT6_SA1    0x00c7
-
-#define    RTL8367C_REG_PKTGEN_PORT6_SA2    0x00c8
-
-#define    RTL8367C_REG_PKTGEN_PORT6_COUNTER0    0x00c9
-
-#define    RTL8367C_REG_PKTGEN_PORT6_COUNTER1    0x00ca
-#define    RTL8367C_PKTGEN_PORT6_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT6_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT6_TX_LENGTH    0x00cb
-#define    RTL8367C_PKTGEN_PORT6_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT6_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT6_TIMER    0x00cd
-#define    RTL8367C_PKTGEN_PORT6_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT6_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT6_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT6_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT6_MISC_CFG    0x00ce
-#define    RTL8367C_PORT6_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT6_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT6_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT6_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT6_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT6_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT6_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT6_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT6_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT6_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT6_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT6_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT6_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT6_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT6_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT6_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT6_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT6_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT6_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT6_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT6_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT6_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT6_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT6_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT6_RATE_CTRL0    0x00cf
-
-#define    RTL8367C_REG_INGRESSBW_PORT6_RATE_CTRL1    0x00d0
-#define    RTL8367C_INGRESSBW_PORT6_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT6_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT6_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT6_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT6_FORCE_RATE0    0x00d1
-
-#define    RTL8367C_REG_PORT6_FORCE_RATE1    0x00d2
-
-#define    RTL8367C_REG_PORT6_CURENT_RATE0    0x00d3
-
-#define    RTL8367C_REG_PORT6_CURENT_RATE1    0x00d4
-
-#define    RTL8367C_REG_PORT6_PAGE_COUNTER    0x00d5
-#define    RTL8367C_PORT6_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT6_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT6_CTRL0    0x00d6
-
-#define    RTL8367C_REG_PAGEMETER_PORT6_CTRL1    0x00d7
-
-#define    RTL8367C_REG_PORT6_EEECFG    0x00d8
-#define    RTL8367C_PORT6_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT6_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT6_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT6_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT6_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT6_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT6_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT6_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT6_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT6_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT6_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT6_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT6_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT6_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT6_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT6_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT6_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT6_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT6_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT6_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT6_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT6_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT6_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT6_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT6_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT6_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT6_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT6_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT6_EEETXMTR    0x00d9
-
-#define    RTL8367C_REG_PORT6_EEERXMTR    0x00da
-
-#define    RTL8367C_REG_PORT6_EEEPTXMTR    0x00db
-
-#define    RTL8367C_REG_PORT6_EEEPRXMTR    0x00dc
-
-#define    RTL8367C_REG_PTP_PORT6_CFG1    0x00de
-#define    RTL8367C_PTP_PORT6_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT6_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P6_MSIC1    0x00df
-#define    RTL8367C_P6_MSIC1_OFFSET    0
-#define    RTL8367C_P6_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT7_CGST_HALF_CFG    0x00e0
-#define    RTL8367C_PORT7_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT7_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT7_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT7_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT7_CTRL    0x00e1
-#define    RTL8367C_PKTGEN_PORT7_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT7_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT7_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT7_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT7_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT7_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT7_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT7_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT7    0x00e2
-#define    RTL8367C_TX_ERR_CNT_PORT7_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT7_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT7_DA0    0x00e3
-
-#define    RTL8367C_REG_PKTGEN_PORT7_DA1    0x00e4
-
-#define    RTL8367C_REG_PKTGEN_PORT7_DA2    0x00e5
-
-#define    RTL8367C_REG_PKTGEN_PORT7_SA0    0x00e6
-
-#define    RTL8367C_REG_PKTGEN_PORT7_SA1    0x00e7
-
-#define    RTL8367C_REG_PKTGEN_PORT7_SA2    0x00e8
-
-#define    RTL8367C_REG_PKTGEN_PORT7_COUNTER0    0x00e9
-
-#define    RTL8367C_REG_PKTGEN_PORT7_COUNTER1    0x00ea
-#define    RTL8367C_PKTGEN_PORT7_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT7_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT7_TX_LENGTH    0x00eb
-#define    RTL8367C_PKTGEN_PORT7_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT7_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT7_TIMER    0x00ed
-#define    RTL8367C_PKTGEN_PORT7_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT7_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT7_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT7_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT7_MISC_CFG    0x00ee
-#define    RTL8367C_PORT7_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT7_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT7_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT7_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT7_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT7_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT7_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT7_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT7_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT7_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT7_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT7_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT7_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT7_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT7_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT7_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT7_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT7_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT7_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT7_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT7_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT7_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT7_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT7_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT7_RATE_CTRL0    0x00ef
-
-#define    RTL8367C_REG_INGRESSBW_PORT7_RATE_CTRL1    0x00f0
-#define    RTL8367C_INGRESSBW_PORT7_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT7_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT7_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT7_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT7_FORCE_RATE0    0x00f1
-
-#define    RTL8367C_REG_PORT7_FORCE_RATE1    0x00f2
-
-#define    RTL8367C_REG_PORT7_CURENT_RATE0    0x00f3
-
-#define    RTL8367C_REG_PORT7_CURENT_RATE1    0x00f4
-
-#define    RTL8367C_REG_PORT7_PAGE_COUNTER    0x00f5
-#define    RTL8367C_PORT7_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT7_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT7_CTRL0    0x00f6
-
-#define    RTL8367C_REG_PAGEMETER_PORT7_CTRL1    0x00f7
-
-#define    RTL8367C_REG_PORT7_EEECFG    0x00f8
-#define    RTL8367C_PORT7_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT7_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT7_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT7_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT7_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT7_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT7_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT7_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT7_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT7_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT7_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT7_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT7_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT7_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT7_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT7_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT7_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT7_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT7_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT7_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT7_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT7_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT7_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT7_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT7_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT7_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT7_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT7_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT7_EEETXMTR    0x00f9
-
-#define    RTL8367C_REG_PORT7_EEERXMTR    0x00fa
-
-#define    RTL8367C_REG_PORT7_EEEPTXMTR    0x00fb
-
-#define    RTL8367C_REG_PORT7_EEEPRXMTR    0x00fc
-
-#define    RTL8367C_REG_PTP_PORT7_CFG1    0x00fe
-#define    RTL8367C_PTP_PORT7_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT7_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P7_MSIC1    0x00ff
-#define    RTL8367C_P7_MSIC1_OFFSET    0
-#define    RTL8367C_P7_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT8_CGST_HALF_CFG    0x0100
-#define    RTL8367C_PORT8_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT8_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT8_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT8_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT8_CTRL    0x0101
-#define    RTL8367C_PKTGEN_PORT8_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT8_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT8_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT8_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT8_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT8_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT8_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT8_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT8    0x0102
-#define    RTL8367C_TX_ERR_CNT_PORT8_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT8_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT8_DA0    0x0103
-
-#define    RTL8367C_REG_PKTGEN_PORT8_DA1    0x0104
-
-#define    RTL8367C_REG_PKTGEN_PORT8_DA2    0x0105
-
-#define    RTL8367C_REG_PKTGEN_PORT8_SA0    0x0106
-
-#define    RTL8367C_REG_PKTGEN_PORT8_SA1    0x0107
-
-#define    RTL8367C_REG_PKTGEN_PORT8_SA2    0x0108
-
-#define    RTL8367C_REG_PKTGEN_PORT8_COUNTER0    0x0109
-
-#define    RTL8367C_REG_PKTGEN_PORT8_COUNTER1    0x010a
-#define    RTL8367C_PKTGEN_PORT8_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT8_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT8_TX_LENGTH    0x010b
-#define    RTL8367C_PKTGEN_PORT8_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT8_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT8_TIMER    0x010d
-#define    RTL8367C_PKTGEN_PORT8_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT8_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT8_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT8_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT8_MISC_CFG    0x010e
-#define    RTL8367C_PORT8_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT8_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT8_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT8_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT8_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT8_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT8_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT8_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT8_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT8_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT8_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT8_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT8_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT8_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT8_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT8_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT8_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT8_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT8_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT8_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT8_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT8_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT8_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT8_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT8_RATE_CTRL0    0x010f
-
-#define    RTL8367C_REG_INGRESSBW_PORT8_RATE_CTRL1    0x0110
-#define    RTL8367C_INGRESSBW_PORT8_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT8_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT8_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT8_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT8_FORCE_RATE0    0x0111
-
-#define    RTL8367C_REG_PORT8_FORCE_RATE1    0x0112
-
-#define    RTL8367C_REG_PORT8_CURENT_RATE0    0x0113
-
-#define    RTL8367C_REG_PORT8_CURENT_RATE1    0x0114
-
-#define    RTL8367C_REG_PORT8_PAGE_COUNTER    0x0115
-#define    RTL8367C_PORT8_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT8_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT8_CTRL0    0x0116
-
-#define    RTL8367C_REG_PAGEMETER_PORT8_CTRL1    0x0117
-
-#define    RTL8367C_REG_PORT8_EEECFG    0x0118
-#define    RTL8367C_PORT8_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT8_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT8_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT8_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT8_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT8_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT8_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT8_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT8_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT8_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT8_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT8_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT8_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT8_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT8_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT8_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT8_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT8_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT8_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT8_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT8_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT8_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT8_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT8_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT8_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT8_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT8_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT8_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT8_EEETXMTR    0x0119
-
-#define    RTL8367C_REG_PORT8_EEERXMTR    0x011a
-
-#define    RTL8367C_REG_PORT8_EEEPTXMTR    0x011b
-
-#define    RTL8367C_REG_PORT8_EEEPRXMTR    0x011c
-
-#define    RTL8367C_REG_PTP_PORT8_CFG1    0x011e
-#define    RTL8367C_PTP_PORT8_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT8_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P8_MSIC1    0x011f
-#define    RTL8367C_P8_MSIC1_OFFSET    0
-#define    RTL8367C_P8_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT9_CGST_HALF_CFG    0x0120
-#define    RTL8367C_PORT9_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT9_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT9_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT9_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT9_CTRL    0x0121
-#define    RTL8367C_PKTGEN_PORT9_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT9_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT9_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT9_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT9_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT9_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT9_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT9_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT9    0x0122
-#define    RTL8367C_TX_ERR_CNT_PORT9_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT9_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT9_DA0    0x0123
-
-#define    RTL8367C_REG_PKTGEN_PORT9_DA1    0x0124
-
-#define    RTL8367C_REG_PKTGEN_PORT9_DA2    0x0125
-
-#define    RTL8367C_REG_PKTGEN_PORT9_SA0    0x0126
-
-#define    RTL8367C_REG_PKTGEN_PORT9_SA1    0x0127
-
-#define    RTL8367C_REG_PKTGEN_PORT9_SA2    0x0128
-
-#define    RTL8367C_REG_PKTGEN_PORT9_COUNTER0    0x0129
-
-#define    RTL8367C_REG_PKTGEN_PORT9_COUNTER1    0x012a
-#define    RTL8367C_PKTGEN_PORT9_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT9_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT9_TX_LENGTH    0x012b
-#define    RTL8367C_PKTGEN_PORT9_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT9_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT9_TIMER    0x012d
-#define    RTL8367C_PKTGEN_PORT9_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT9_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT9_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT9_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT9_MISC_CFG    0x012e
-#define    RTL8367C_PORT9_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT9_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT9_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT9_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT9_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT9_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT9_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT9_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT9_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT9_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT9_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT9_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT9_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT9_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT9_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT9_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT9_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT9_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT9_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT9_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT9_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT9_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT9_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT9_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT9_RATE_CTRL0    0x012f
-
-#define    RTL8367C_REG_INGRESSBW_PORT9_RATE_CTRL1    0x0130
-#define    RTL8367C_INGRESSBW_PORT9_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT9_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT9_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT9_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT9_FORCE_RATE0    0x0131
-
-#define    RTL8367C_REG_PORT9_FORCE_RATE1    0x0132
-
-#define    RTL8367C_REG_PORT9_CURENT_RATE0    0x0133
-
-#define    RTL8367C_REG_PORT9_CURENT_RATE1    0x0134
-
-#define    RTL8367C_REG_PORT9_PAGE_COUNTER    0x0135
-#define    RTL8367C_PORT9_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT9_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT9_CTRL0    0x0136
-
-#define    RTL8367C_REG_PAGEMETER_PORT9_CTRL1    0x0137
-
-#define    RTL8367C_REG_PORT9_EEECFG    0x0138
-#define    RTL8367C_PORT9_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT9_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT9_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT9_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT9_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT9_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT9_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT9_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT9_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT9_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT9_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT9_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT9_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT9_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT9_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT9_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT9_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT9_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT9_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT9_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT9_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT9_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT9_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT9_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT9_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT9_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT9_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT9_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT9_EEETXMTR    0x0139
-
-#define    RTL8367C_REG_PORT9_EEERXMTR    0x013a
-
-#define    RTL8367C_REG_PORT9_EEEPTXMTR    0x013b
-
-#define    RTL8367C_REG_PORT9_EEEPRXMTR    0x013c
-
-#define    RTL8367C_REG_PTP_PORT9_CFG1    0x013e
-#define    RTL8367C_PTP_PORT9_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT9_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P9_MSIC1    0x013f
-#define    RTL8367C_P9_MSIC1_OFFSET    0
-#define    RTL8367C_P9_MSIC1_MASK    0x1
-
-#define    RTL8367C_REG_PORT10_CGST_HALF_CFG    0x0140
-#define    RTL8367C_PORT10_CGST_HALF_CFG_CONGESTION_TIME_OFFSET    4
-#define    RTL8367C_PORT10_CGST_HALF_CFG_CONGESTION_TIME_MASK    0xF0
-#define    RTL8367C_PORT10_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT10_CGST_HALF_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_PKTGEN_PORT10_CTRL    0x0141
-#define    RTL8367C_PKTGEN_PORT10_CTRL_STATUS_OFFSET    15
-#define    RTL8367C_PKTGEN_PORT10_CTRL_STATUS_MASK    0x8000
-#define    RTL8367C_PKTGEN_PORT10_CTRL_PKTGEN_STS_OFFSET    13
-#define    RTL8367C_PKTGEN_PORT10_CTRL_PKTGEN_STS_MASK    0x2000
-#define    RTL8367C_PKTGEN_PORT10_CTRL_CRC_NO_ERROR_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT10_CTRL_CRC_NO_ERROR_MASK    0x10
-#define    RTL8367C_PKTGEN_PORT10_CTRL_CMD_START_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT10_CTRL_CMD_START_MASK    0x1
-
-#define    RTL8367C_REG_TX_ERR_CNT_PORT10    0x0142
-#define    RTL8367C_TX_ERR_CNT_PORT10_OFFSET    0
-#define    RTL8367C_TX_ERR_CNT_PORT10_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_PORT10_DA0    0x0143
-
-#define    RTL8367C_REG_PKTGEN_PORT10_DA1    0x0144
-
-#define    RTL8367C_REG_PKTGEN_PORT10_DA2    0x0145
-
-#define    RTL8367C_REG_PKTGEN_PORT10_SA0    0x0146
-
-#define    RTL8367C_REG_PKTGEN_PORT10_SA1    0x0147
-
-#define    RTL8367C_REG_PKTGEN_PORT10_SA2    0x0148
-
-#define    RTL8367C_REG_PKTGEN_PORT10_COUNTER0    0x0149
-
-#define    RTL8367C_REG_PKTGEN_PORT10_COUNTER1    0x014a
-#define    RTL8367C_PKTGEN_PORT10_COUNTER1_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT10_COUNTER1_MASK    0xFF
-
-#define    RTL8367C_REG_PKTGEN_PORT10_TX_LENGTH    0x014b
-#define    RTL8367C_PKTGEN_PORT10_TX_LENGTH_OFFSET    0
-#define    RTL8367C_PKTGEN_PORT10_TX_LENGTH_MASK    0x3FFF
-
-#define    RTL8367C_REG_PKTGEN_PORT10_TIMER    0x014d
-#define    RTL8367C_PKTGEN_PORT10_TIMER_TIMER_OFFSET    4
-#define    RTL8367C_PKTGEN_PORT10_TIMER_TIMER_MASK    0xF0
-#define    RTL8367C_PKTGEN_PORT10_TIMER_RX_DMA_ERR_FLAG_OFFSET    3
-#define    RTL8367C_PKTGEN_PORT10_TIMER_RX_DMA_ERR_FLAG_MASK    0x8
-
-#define    RTL8367C_REG_PORT10_MISC_CFG    0x014e
-#define    RTL8367C_PORT10_MISC_CFG_SMALL_TAG_IPG_OFFSET    15
-#define    RTL8367C_PORT10_MISC_CFG_SMALL_TAG_IPG_MASK    0x8000
-#define    RTL8367C_PORT10_MISC_CFG_TX_ITFSP_MODE_OFFSET    14
-#define    RTL8367C_PORT10_MISC_CFG_TX_ITFSP_MODE_MASK    0x4000
-#define    RTL8367C_PORT10_MISC_CFG_FLOWCTRL_INDEP_OFFSET    13
-#define    RTL8367C_PORT10_MISC_CFG_FLOWCTRL_INDEP_MASK    0x2000
-#define    RTL8367C_PORT10_MISC_CFG_DOT1Q_REMARK_ENABLE_OFFSET    12
-#define    RTL8367C_PORT10_MISC_CFG_DOT1Q_REMARK_ENABLE_MASK    0x1000
-#define    RTL8367C_PORT10_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET    11
-#define    RTL8367C_PORT10_MISC_CFG_INGRESSBW_FLOWCTRL_MASK    0x800
-#define    RTL8367C_PORT10_MISC_CFG_INGRESSBW_IFG_OFFSET    10
-#define    RTL8367C_PORT10_MISC_CFG_INGRESSBW_IFG_MASK    0x400
-#define    RTL8367C_PORT10_MISC_CFG_RX_SPC_OFFSET    9
-#define    RTL8367C_PORT10_MISC_CFG_RX_SPC_MASK    0x200
-#define    RTL8367C_PORT10_MISC_CFG_CRC_SKIP_OFFSET    8
-#define    RTL8367C_PORT10_MISC_CFG_CRC_SKIP_MASK    0x100
-#define    RTL8367C_PORT10_MISC_CFG_PKTGEN_TX_FIRST_OFFSET    7
-#define    RTL8367C_PORT10_MISC_CFG_PKTGEN_TX_FIRST_MASK    0x80
-#define    RTL8367C_PORT10_MISC_CFG_MAC_LOOPBACK_OFFSET    6
-#define    RTL8367C_PORT10_MISC_CFG_MAC_LOOPBACK_MASK    0x40
-#define    RTL8367C_PORT10_MISC_CFG_VLAN_EGRESS_MODE_OFFSET    4
-#define    RTL8367C_PORT10_MISC_CFG_VLAN_EGRESS_MODE_MASK    0x30
-#define    RTL8367C_PORT10_MISC_CFG_CONGESTION_SUSTAIN_TIME_OFFSET    0
-#define    RTL8367C_PORT10_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK    0xF
-
-#define    RTL8367C_REG_INGRESSBW_PORT10_RATE_CTRL0    0x014f
-
-#define    RTL8367C_REG_INGRESSBW_PORT10_RATE_CTRL1    0x0150
-#define    RTL8367C_INGRESSBW_PORT10_RATE_CTRL1_DUMMY_OFFSET    3
-#define    RTL8367C_INGRESSBW_PORT10_RATE_CTRL1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_INGRESSBW_PORT10_RATE_CTRL1_INGRESSBW_RATE16_OFFSET    0
-#define    RTL8367C_INGRESSBW_PORT10_RATE_CTRL1_INGRESSBW_RATE16_MASK    0x7
-
-#define    RTL8367C_REG_PORT10_FORCE_RATE0    0x0151
-
-#define    RTL8367C_REG_PORT10_FORCE_RATE1    0x0152
-
-#define    RTL8367C_REG_PORT10_CURENT_RATE0    0x0153
-
-#define    RTL8367C_REG_PORT10_CURENT_RATE1    0x0154
-
-#define    RTL8367C_REG_PORT10_PAGE_COUNTER    0x0155
-#define    RTL8367C_PORT10_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_PORT10_PAGE_COUNTER_MASK    0x7F
-
-#define    RTL8367C_REG_PAGEMETER_PORT10_CTRL0    0x0156
-
-#define    RTL8367C_REG_PAGEMETER_PORT10_CTRL1    0x0157
-
-#define    RTL8367C_REG_PORT10_EEECFG    0x0158
-#define    RTL8367C_PORT10_EEECFG_EEEP_ENABLE_TX_OFFSET    14
-#define    RTL8367C_PORT10_EEECFG_EEEP_ENABLE_TX_MASK    0x4000
-#define    RTL8367C_PORT10_EEECFG_EEEP_ENABLE_RX_OFFSET    13
-#define    RTL8367C_PORT10_EEECFG_EEEP_ENABLE_RX_MASK    0x2000
-#define    RTL8367C_PORT10_EEECFG_EEE_FORCE_OFFSET    12
-#define    RTL8367C_PORT10_EEECFG_EEE_FORCE_MASK    0x1000
-#define    RTL8367C_PORT10_EEECFG_EEE_100M_OFFSET    11
-#define    RTL8367C_PORT10_EEECFG_EEE_100M_MASK    0x800
-#define    RTL8367C_PORT10_EEECFG_EEE_GIGA_500M_OFFSET    10
-#define    RTL8367C_PORT10_EEECFG_EEE_GIGA_500M_MASK    0x400
-#define    RTL8367C_PORT10_EEECFG_EEE_TX_OFFSET    9
-#define    RTL8367C_PORT10_EEECFG_EEE_TX_MASK    0x200
-#define    RTL8367C_PORT10_EEECFG_EEE_RX_OFFSET    8
-#define    RTL8367C_PORT10_EEECFG_EEE_RX_MASK    0x100
-#define    RTL8367C_PORT10_EEECFG_EEE_DSP_RX_OFFSET    6
-#define    RTL8367C_PORT10_EEECFG_EEE_DSP_RX_MASK    0x40
-#define    RTL8367C_PORT10_EEECFG_EEE_LPI_OFFSET    5
-#define    RTL8367C_PORT10_EEECFG_EEE_LPI_MASK    0x20
-#define    RTL8367C_PORT10_EEECFG_EEE_TX_LPI_OFFSET    4
-#define    RTL8367C_PORT10_EEECFG_EEE_TX_LPI_MASK    0x10
-#define    RTL8367C_PORT10_EEECFG_EEE_RX_LPI_OFFSET    3
-#define    RTL8367C_PORT10_EEECFG_EEE_RX_LPI_MASK    0x8
-#define    RTL8367C_PORT10_EEECFG_EEE_PAUSE_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT10_EEECFG_EEE_PAUSE_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT10_EEECFG_EEE_WAKE_REQ_OFFSET    1
-#define    RTL8367C_PORT10_EEECFG_EEE_WAKE_REQ_MASK    0x2
-#define    RTL8367C_PORT10_EEECFG_EEE_SLEEP_REQ_OFFSET    0
-#define    RTL8367C_PORT10_EEECFG_EEE_SLEEP_REQ_MASK    0x1
-
-#define    RTL8367C_REG_PORT10_EEETXMTR    0x0159
-
-#define    RTL8367C_REG_PORT10_EEERXMTR    0x015a
-
-#define    RTL8367C_REG_PORT10_EEEPTXMTR    0x015b
-
-#define    RTL8367C_REG_PORT10_EEEPRXMTR    0x015c
-
-#define    RTL8367C_REG_PTP_PORT10_CFG1    0x015e
-#define    RTL8367C_PTP_PORT10_CFG1_OFFSET    7
-#define    RTL8367C_PTP_PORT10_CFG1_MASK    0xFF
-
-#define    RTL8367C_REG_P10_MSIC1    0x015f
-#define    RTL8367C_P10_MSIC1_OFFSET    0
-#define    RTL8367C_P10_MSIC1_MASK    0x1
-
-/* (16'h0200)outq_reg */
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE0_DROP_ON    0x0200
-#define    RTL8367C_FLOWCTRL_QUEUE0_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE0_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE1_DROP_ON    0x0201
-#define    RTL8367C_FLOWCTRL_QUEUE1_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE1_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE2_DROP_ON    0x0202
-#define    RTL8367C_FLOWCTRL_QUEUE2_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE2_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE3_DROP_ON    0x0203
-#define    RTL8367C_FLOWCTRL_QUEUE3_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE3_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE4_DROP_ON    0x0204
-#define    RTL8367C_FLOWCTRL_QUEUE4_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE4_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE5_DROP_ON    0x0205
-#define    RTL8367C_FLOWCTRL_QUEUE5_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE5_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE6_DROP_ON    0x0206
-#define    RTL8367C_FLOWCTRL_QUEUE6_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE6_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE7_DROP_ON    0x0207
-#define    RTL8367C_FLOWCTRL_QUEUE7_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE7_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT0_DROP_ON    0x0208
-#define    RTL8367C_FLOWCTRL_PORT0_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT0_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT1_DROP_ON    0x0209
-#define    RTL8367C_FLOWCTRL_PORT1_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT1_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT2_DROP_ON    0x020a
-#define    RTL8367C_FLOWCTRL_PORT2_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT2_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT3_DROP_ON    0x020b
-#define    RTL8367C_FLOWCTRL_PORT3_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT3_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT4_DROP_ON    0x020c
-#define    RTL8367C_FLOWCTRL_PORT4_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT4_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT5_DROP_ON    0x020d
-#define    RTL8367C_FLOWCTRL_PORT5_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT5_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT6_DROP_ON    0x020e
-#define    RTL8367C_FLOWCTRL_PORT6_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT6_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT7_DROP_ON    0x020f
-#define    RTL8367C_FLOWCTRL_PORT7_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT7_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT8_DROP_ON    0x0210
-#define    RTL8367C_FLOWCTRL_PORT8_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT8_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT9_DROP_ON    0x0211
-#define    RTL8367C_FLOWCTRL_PORT9_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT9_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT10_DROP_ON    0x0212
-#define    RTL8367C_FLOWCTRL_PORT10_DROP_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT10_DROP_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT_GAP    0x0218
-#define    RTL8367C_FLOWCTRL_PORT_GAP_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT_GAP_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE_GAP    0x0219
-#define    RTL8367C_FLOWCTRL_QUEUE_GAP_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE_GAP_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_QEMPTY    0x022d
-#define    RTL8367C_PORT_QEMPTY_OFFSET    0
-#define    RTL8367C_PORT_QEMPTY_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_DEBUG_CTRL0    0x022e
-#define    RTL8367C_FLOWCTRL_DEBUG_CTRL0_OFFSET    0
-#define    RTL8367C_FLOWCTRL_DEBUG_CTRL0_MASK    0xF
-
-#define    RTL8367C_REG_FLOWCTRL_DEBUG_CTRL1    0x022f
-#define    RTL8367C_TOTAL_OFFSET    9
-#define    RTL8367C_TOTAL_MASK    0x200
-#define    RTL8367C_PORT_MAX_OFFSET    8
-#define    RTL8367C_PORT_MAX_MASK    0x100
-#define    RTL8367C_QMAX_MASK_OFFSET    0
-#define    RTL8367C_QMAX_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE0_PAGE_COUNT    0x0230
-#define    RTL8367C_FLOWCTRL_QUEUE0_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE0_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE1_PAGE_COUNT    0x0231
-#define    RTL8367C_FLOWCTRL_QUEUE1_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE1_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE2_PAGE_COUNT    0x0232
-#define    RTL8367C_FLOWCTRL_QUEUE2_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE2_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE3_PAGE_COUNT    0x0233
-#define    RTL8367C_FLOWCTRL_QUEUE3_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE3_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE4_PAGE_COUNT    0x0234
-#define    RTL8367C_FLOWCTRL_QUEUE4_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE4_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE5_PAGE_COUNT    0x0235
-#define    RTL8367C_FLOWCTRL_QUEUE5_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE5_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE6_PAGE_COUNT    0x0236
-#define    RTL8367C_FLOWCTRL_QUEUE6_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE6_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE7_PAGE_COUNT    0x0237
-#define    RTL8367C_FLOWCTRL_QUEUE7_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE7_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT_PAGE_COUNT    0x0238
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE0_MAX_PAGE_COUNT    0x0239
-#define    RTL8367C_FLOWCTRL_QUEUE0_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE0_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE1_MAX_PAGE_COUNT    0x023a
-#define    RTL8367C_FLOWCTRL_QUEUE1_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE1_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE2_MAX_PAGE_COUNT    0x023b
-#define    RTL8367C_FLOWCTRL_QUEUE2_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE2_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE3_MAX_PAGE_COUNT    0x023c
-#define    RTL8367C_FLOWCTRL_QUEUE3_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE3_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE4_MAX_PAGE_COUNT    0x023d
-#define    RTL8367C_FLOWCTRL_QUEUE4_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE4_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE5_MAX_PAGE_COUNT    0x023e
-#define    RTL8367C_FLOWCTRL_QUEUE5_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE5_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE6_MAX_PAGE_COUNT    0x023f
-#define    RTL8367C_FLOWCTRL_QUEUE6_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE6_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_QUEUE7_MAX_PAGE_COUNT    0x0240
-#define    RTL8367C_FLOWCTRL_QUEUE7_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_QUEUE7_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT_MAX_PAGE_COUNT    0x0241
-#define    RTL8367C_FLOWCTRL_PORT_MAX_PAGE_COUNT_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT_MAX_PAGE_COUNT_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_TOTAL_PACKET_COUNT    0x0243
-
-#define    RTL8367C_REG_HIGH_QUEUE_MASK0    0x0244
-#define    RTL8367C_PORT1_HIGH_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT1_HIGH_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT0_HIGH_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT0_HIGH_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_HIGH_QUEUE_MASK1    0x0245
-#define    RTL8367C_PORT3_HIGH_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT3_HIGH_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT2_HIGH_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT2_HIGH_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_HIGH_QUEUE_MASK2    0x0246
-#define    RTL8367C_PORT5_HIGH_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT5_HIGH_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT4_HIGH_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT4_HIGH_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_HIGH_QUEUE_MASK3    0x0247
-#define    RTL8367C_PORT7_HIGH_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT7_HIGH_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT6_HIGH_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT6_HIGH_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_HIGH_QUEUE_MASK4    0x0248
-#define    RTL8367C_PORT9_HIGH_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT9_HIGH_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT8_HIGH_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT8_HIGH_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_HIGH_QUEUE_MASK5    0x0249
-#define    RTL8367C_HIGH_QUEUE_MASK5_OFFSET    0
-#define    RTL8367C_HIGH_QUEUE_MASK5_MASK    0xFF
-
-#define    RTL8367C_REG_LOW_QUEUE_TH    0x024c
-#define    RTL8367C_LOW_QUEUE_TH_OFFSET    0
-#define    RTL8367C_LOW_QUEUE_TH_MASK    0x7FF
-
-#define    RTL8367C_REG_TH_TX_PREFET    0x0250
-#define    RTL8367C_TH_TX_PREFET_OFFSET    0
-#define    RTL8367C_TH_TX_PREFET_MASK    0xFF
-
-#define    RTL8367C_REG_DUMMY_0251    0x0251
-
-#define    RTL8367C_REG_DUMMY_0252    0x0252
-
-#define    RTL8367C_REG_DUMMY_0253    0x0253
-
-#define    RTL8367C_REG_DUMMY_0254    0x0254
-
-#define    RTL8367C_REG_DUMMY_0255    0x0255
-
-#define    RTL8367C_REG_DUMMY_0256    0x0256
-
-#define    RTL8367C_REG_DUMMY_0257    0x0257
-
-#define    RTL8367C_REG_DUMMY_0258    0x0258
-
-#define    RTL8367C_REG_DUMMY_0259    0x0259
-
-#define    RTL8367C_REG_DUMMY_025A    0x025A
-
-#define    RTL8367C_REG_DUMMY_025B    0x025B
-
-#define    RTL8367C_REG_DUMMY_025C    0x025C
-
-#define    RTL8367C_REG_Q_TXPKT_CNT_CTL    0x025d
-#define    RTL8367C_QUEUE_PKT_CNT_CLR_OFFSET    4
-#define    RTL8367C_QUEUE_PKT_CNT_CLR_MASK    0x10
-#define    RTL8367C_PORT_ID_QUEUE_PKT_CNT_OFFSET    0
-#define    RTL8367C_PORT_ID_QUEUE_PKT_CNT_MASK    0xF
-
-#define    RTL8367C_REG_Q0_TXPKT_CNT_L    0x025e
-
-#define    RTL8367C_REG_Q0_TXPKT_CNT_H    0x025f
-
-#define    RTL8367C_REG_Q1_TXPKT_CNT_L    0x0260
-
-#define    RTL8367C_REG_Q1_TXPKT_CNT_H    0x0261
-
-#define    RTL8367C_REG_Q2_TXPKT_CNT_L    0x0262
-
-#define    RTL8367C_REG_Q2_TXPKT_CNT_H    0x0263
-
-#define    RTL8367C_REG_Q3_TXPKT_CNT_L    0x0264
-
-#define    RTL8367C_REG_Q3_TXPKT_CNT_H    0x0265
-
-#define    RTL8367C_REG_Q4_TXPKT_CNT_L    0x0266
-
-#define    RTL8367C_REG_Q4_TXPKT_CNT_H    0x0267
-
-#define    RTL8367C_REG_Q5_TXPKT_CNT_L    0x0268
-
-#define    RTL8367C_REG_Q5_TXPKT_CNT_H    0x0269
-
-#define    RTL8367C_REG_Q6_TXPKT_CNT_L    0x026a
-
-#define    RTL8367C_REG_Q6_TXPKT_CNT_H    0x026b
-
-#define    RTL8367C_REG_Q7_TXPKT_CNT_L    0x026c
-
-#define    RTL8367C_REG_Q7_TXPKT_CNT_H    0x026d
-
-/* (16'h0300)sch_reg */
-
-#define    RTL8367C_REG_SCHEDULE_WFQ_CTRL    0x0300
-#define    RTL8367C_SCHEDULE_WFQ_CTRL_OFFSET    0
-#define    RTL8367C_SCHEDULE_WFQ_CTRL_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_WFQ_BURST_SIZE    0x0301
-
-#define    RTL8367C_REG_SCHEDULE_QUEUE_TYPE_CTRL0    0x0302
-#define    RTL8367C_PORT1_QUEUE7_TYPE_OFFSET    15
-#define    RTL8367C_PORT1_QUEUE7_TYPE_MASK    0x8000
-#define    RTL8367C_PORT1_QUEUE6_TYPE_OFFSET    14
-#define    RTL8367C_PORT1_QUEUE6_TYPE_MASK    0x4000
-#define    RTL8367C_PORT1_QUEUE5_TYPE_OFFSET    13
-#define    RTL8367C_PORT1_QUEUE5_TYPE_MASK    0x2000
-#define    RTL8367C_PORT1_QUEUE4_TYPE_OFFSET    12
-#define    RTL8367C_PORT1_QUEUE4_TYPE_MASK    0x1000
-#define    RTL8367C_PORT1_QUEUE3_TYPE_OFFSET    11
-#define    RTL8367C_PORT1_QUEUE3_TYPE_MASK    0x800
-#define    RTL8367C_PORT1_QUEUE2_TYPE_OFFSET    10
-#define    RTL8367C_PORT1_QUEUE2_TYPE_MASK    0x400
-#define    RTL8367C_PORT1_QUEUE1_TYPE_OFFSET    9
-#define    RTL8367C_PORT1_QUEUE1_TYPE_MASK    0x200
-#define    RTL8367C_PORT1_QUEUE0_TYPE_OFFSET    8
-#define    RTL8367C_PORT1_QUEUE0_TYPE_MASK    0x100
-#define    RTL8367C_PORT0_QUEUE7_TYPE_OFFSET    7
-#define    RTL8367C_PORT0_QUEUE7_TYPE_MASK    0x80
-#define    RTL8367C_PORT0_QUEUE6_TYPE_OFFSET    6
-#define    RTL8367C_PORT0_QUEUE6_TYPE_MASK    0x40
-#define    RTL8367C_PORT0_QUEUE5_TYPE_OFFSET    5
-#define    RTL8367C_PORT0_QUEUE5_TYPE_MASK    0x20
-#define    RTL8367C_PORT0_QUEUE4_TYPE_OFFSET    4
-#define    RTL8367C_PORT0_QUEUE4_TYPE_MASK    0x10
-#define    RTL8367C_PORT0_QUEUE3_TYPE_OFFSET    3
-#define    RTL8367C_PORT0_QUEUE3_TYPE_MASK    0x8
-#define    RTL8367C_PORT0_QUEUE2_TYPE_OFFSET    2
-#define    RTL8367C_PORT0_QUEUE2_TYPE_MASK    0x4
-#define    RTL8367C_PORT0_QUEUE1_TYPE_OFFSET    1
-#define    RTL8367C_PORT0_QUEUE1_TYPE_MASK    0x2
-#define    RTL8367C_PORT0_QUEUE0_TYPE_OFFSET    0
-#define    RTL8367C_PORT0_QUEUE0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_QUEUE_TYPE_CTRL1    0x0303
-#define    RTL8367C_PORT3_QUEUE7_TYPE_OFFSET    15
-#define    RTL8367C_PORT3_QUEUE7_TYPE_MASK    0x8000
-#define    RTL8367C_PORT3_QUEUE6_TYPE_OFFSET    14
-#define    RTL8367C_PORT3_QUEUE6_TYPE_MASK    0x4000
-#define    RTL8367C_PORT3_QUEUE5_TYPE_OFFSET    13
-#define    RTL8367C_PORT3_QUEUE5_TYPE_MASK    0x2000
-#define    RTL8367C_PORT3_QUEUE4_TYPE_OFFSET    12
-#define    RTL8367C_PORT3_QUEUE4_TYPE_MASK    0x1000
-#define    RTL8367C_PORT3_QUEUE3_TYPE_OFFSET    11
-#define    RTL8367C_PORT3_QUEUE3_TYPE_MASK    0x800
-#define    RTL8367C_PORT3_QUEUE2_TYPE_OFFSET    10
-#define    RTL8367C_PORT3_QUEUE2_TYPE_MASK    0x400
-#define    RTL8367C_PORT3_QUEUE1_TYPE_OFFSET    9
-#define    RTL8367C_PORT3_QUEUE1_TYPE_MASK    0x200
-#define    RTL8367C_PORT3_QUEUE0_TYPE_OFFSET    8
-#define    RTL8367C_PORT3_QUEUE0_TYPE_MASK    0x100
-#define    RTL8367C_PORT2_QUEUE7_TYPE_OFFSET    7
-#define    RTL8367C_PORT2_QUEUE7_TYPE_MASK    0x80
-#define    RTL8367C_PORT2_QUEUE6_TYPE_OFFSET    6
-#define    RTL8367C_PORT2_QUEUE6_TYPE_MASK    0x40
-#define    RTL8367C_PORT2_QUEUE5_TYPE_OFFSET    5
-#define    RTL8367C_PORT2_QUEUE5_TYPE_MASK    0x20
-#define    RTL8367C_PORT2_QUEUE4_TYPE_OFFSET    4
-#define    RTL8367C_PORT2_QUEUE4_TYPE_MASK    0x10
-#define    RTL8367C_PORT2_QUEUE3_TYPE_OFFSET    3
-#define    RTL8367C_PORT2_QUEUE3_TYPE_MASK    0x8
-#define    RTL8367C_PORT2_QUEUE2_TYPE_OFFSET    2
-#define    RTL8367C_PORT2_QUEUE2_TYPE_MASK    0x4
-#define    RTL8367C_PORT2_QUEUE1_TYPE_OFFSET    1
-#define    RTL8367C_PORT2_QUEUE1_TYPE_MASK    0x2
-#define    RTL8367C_PORT2_QUEUE0_TYPE_OFFSET    0
-#define    RTL8367C_PORT2_QUEUE0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_QUEUE_TYPE_CTRL2    0x0304
-#define    RTL8367C_PORT5_QUEUE7_TYPE_OFFSET    15
-#define    RTL8367C_PORT5_QUEUE7_TYPE_MASK    0x8000
-#define    RTL8367C_PORT5_QUEUE6_TYPE_OFFSET    14
-#define    RTL8367C_PORT5_QUEUE6_TYPE_MASK    0x4000
-#define    RTL8367C_PORT5_QUEUE5_TYPE_OFFSET    13
-#define    RTL8367C_PORT5_QUEUE5_TYPE_MASK    0x2000
-#define    RTL8367C_PORT5_QUEUE4_TYPE_OFFSET    12
-#define    RTL8367C_PORT5_QUEUE4_TYPE_MASK    0x1000
-#define    RTL8367C_PORT5_QUEUE3_TYPE_OFFSET    11
-#define    RTL8367C_PORT5_QUEUE3_TYPE_MASK    0x800
-#define    RTL8367C_PORT5_QUEUE2_TYPE_OFFSET    10
-#define    RTL8367C_PORT5_QUEUE2_TYPE_MASK    0x400
-#define    RTL8367C_PORT5_QUEUE1_TYPE_OFFSET    9
-#define    RTL8367C_PORT5_QUEUE1_TYPE_MASK    0x200
-#define    RTL8367C_PORT5_QUEUE0_TYPE_OFFSET    8
-#define    RTL8367C_PORT5_QUEUE0_TYPE_MASK    0x100
-#define    RTL8367C_PORT4_QUEUE7_TYPE_OFFSET    7
-#define    RTL8367C_PORT4_QUEUE7_TYPE_MASK    0x80
-#define    RTL8367C_PORT4_QUEUE6_TYPE_OFFSET    6
-#define    RTL8367C_PORT4_QUEUE6_TYPE_MASK    0x40
-#define    RTL8367C_PORT4_QUEUE5_TYPE_OFFSET    5
-#define    RTL8367C_PORT4_QUEUE5_TYPE_MASK    0x20
-#define    RTL8367C_PORT4_QUEUE4_TYPE_OFFSET    4
-#define    RTL8367C_PORT4_QUEUE4_TYPE_MASK    0x10
-#define    RTL8367C_PORT4_QUEUE3_TYPE_OFFSET    3
-#define    RTL8367C_PORT4_QUEUE3_TYPE_MASK    0x8
-#define    RTL8367C_PORT4_QUEUE2_TYPE_OFFSET    2
-#define    RTL8367C_PORT4_QUEUE2_TYPE_MASK    0x4
-#define    RTL8367C_PORT4_QUEUE1_TYPE_OFFSET    1
-#define    RTL8367C_PORT4_QUEUE1_TYPE_MASK    0x2
-#define    RTL8367C_PORT4_QUEUE0_TYPE_OFFSET    0
-#define    RTL8367C_PORT4_QUEUE0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_QUEUE_TYPE_CTRL3    0x0305
-#define    RTL8367C_PORT7_QUEUE7_TYPE_OFFSET    15
-#define    RTL8367C_PORT7_QUEUE7_TYPE_MASK    0x8000
-#define    RTL8367C_PORT7_QUEUE6_TYPE_OFFSET    14
-#define    RTL8367C_PORT7_QUEUE6_TYPE_MASK    0x4000
-#define    RTL8367C_PORT7_QUEUE5_TYPE_OFFSET    13
-#define    RTL8367C_PORT7_QUEUE5_TYPE_MASK    0x2000
-#define    RTL8367C_PORT7_QUEUE4_TYPE_OFFSET    12
-#define    RTL8367C_PORT7_QUEUE4_TYPE_MASK    0x1000
-#define    RTL8367C_PORT7_QUEUE3_TYPE_OFFSET    11
-#define    RTL8367C_PORT7_QUEUE3_TYPE_MASK    0x800
-#define    RTL8367C_PORT7_QUEUE2_TYPE_OFFSET    10
-#define    RTL8367C_PORT7_QUEUE2_TYPE_MASK    0x400
-#define    RTL8367C_PORT7_QUEUE1_TYPE_OFFSET    9
-#define    RTL8367C_PORT7_QUEUE1_TYPE_MASK    0x200
-#define    RTL8367C_PORT7_QUEUE0_TYPE_OFFSET    8
-#define    RTL8367C_PORT7_QUEUE0_TYPE_MASK    0x100
-#define    RTL8367C_PORT6_QUEUE7_TYPE_OFFSET    7
-#define    RTL8367C_PORT6_QUEUE7_TYPE_MASK    0x80
-#define    RTL8367C_PORT6_QUEUE6_TYPE_OFFSET    6
-#define    RTL8367C_PORT6_QUEUE6_TYPE_MASK    0x40
-#define    RTL8367C_PORT6_QUEUE5_TYPE_OFFSET    5
-#define    RTL8367C_PORT6_QUEUE5_TYPE_MASK    0x20
-#define    RTL8367C_PORT6_QUEUE4_TYPE_OFFSET    4
-#define    RTL8367C_PORT6_QUEUE4_TYPE_MASK    0x10
-#define    RTL8367C_PORT6_QUEUE3_TYPE_OFFSET    3
-#define    RTL8367C_PORT6_QUEUE3_TYPE_MASK    0x8
-#define    RTL8367C_PORT6_QUEUE2_TYPE_OFFSET    2
-#define    RTL8367C_PORT6_QUEUE2_TYPE_MASK    0x4
-#define    RTL8367C_PORT6_QUEUE1_TYPE_OFFSET    1
-#define    RTL8367C_PORT6_QUEUE1_TYPE_MASK    0x2
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_CTRL3_PORT6_QUEUE0_TYPE_OFFSET    0
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_CTRL3_PORT6_QUEUE0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_QUEUE_TYPE_CTRL4    0x0306
-#define    RTL8367C_PORT9_QUEUE7_TYPE_OFFSET    15
-#define    RTL8367C_PORT9_QUEUE7_TYPE_MASK    0x8000
-#define    RTL8367C_PORT9_QUEUE6_TYPE_OFFSET    14
-#define    RTL8367C_PORT9_QUEUE6_TYPE_MASK    0x4000
-#define    RTL8367C_PORT9_QUEUE5_TYPE_OFFSET    13
-#define    RTL8367C_PORT9_QUEUE5_TYPE_MASK    0x2000
-#define    RTL8367C_PORT9_QUEUE4_TYPE_OFFSET    12
-#define    RTL8367C_PORT9_QUEUE4_TYPE_MASK    0x1000
-#define    RTL8367C_PORT9_QUEUE3_TYPE_OFFSET    11
-#define    RTL8367C_PORT9_QUEUE3_TYPE_MASK    0x800
-#define    RTL8367C_PORT9_QUEUE2_TYPE_OFFSET    10
-#define    RTL8367C_PORT9_QUEUE2_TYPE_MASK    0x400
-#define    RTL8367C_PORT9_QUEUE1_TYPE_OFFSET    9
-#define    RTL8367C_PORT9_QUEUE1_TYPE_MASK    0x200
-#define    RTL8367C_PORT9_QUEUE0_TYPE_OFFSET    8
-#define    RTL8367C_PORT9_QUEUE0_TYPE_MASK    0x100
-#define    RTL8367C_PORT8_QUEUE7_TYPE_OFFSET    7
-#define    RTL8367C_PORT8_QUEUE7_TYPE_MASK    0x80
-#define    RTL8367C_PORT8_QUEUE6_TYPE_OFFSET    6
-#define    RTL8367C_PORT8_QUEUE6_TYPE_MASK    0x40
-#define    RTL8367C_PORT8_QUEUE5_TYPE_OFFSET    5
-#define    RTL8367C_PORT8_QUEUE5_TYPE_MASK    0x20
-#define    RTL8367C_PORT8_QUEUE4_TYPE_OFFSET    4
-#define    RTL8367C_PORT8_QUEUE4_TYPE_MASK    0x10
-#define    RTL8367C_PORT8_QUEUE3_TYPE_OFFSET    3
-#define    RTL8367C_PORT8_QUEUE3_TYPE_MASK    0x8
-#define    RTL8367C_PORT8_QUEUE2_TYPE_OFFSET    2
-#define    RTL8367C_PORT8_QUEUE2_TYPE_MASK    0x4
-#define    RTL8367C_PORT8_QUEUE1_TYPE_OFFSET    1
-#define    RTL8367C_PORT8_QUEUE1_TYPE_MASK    0x2
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_CTRL4_PORT6_QUEUE0_TYPE_OFFSET    0
-#define    RTL8367C_SCHEDULE_QUEUE_TYPE_CTRL4_PORT6_QUEUE0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_QUEUE_TYPE_CTRL5    0x0307
-#define    RTL8367C_PORT10_QUEUE7_TYPE_OFFSET    7
-#define    RTL8367C_PORT10_QUEUE7_TYPE_MASK    0x80
-#define    RTL8367C_PORT10_QUEUE6_TYPE_OFFSET    6
-#define    RTL8367C_PORT10_QUEUE6_TYPE_MASK    0x40
-#define    RTL8367C_PORT10_QUEUE5_TYPE_OFFSET    5
-#define    RTL8367C_PORT10_QUEUE5_TYPE_MASK    0x20
-#define    RTL8367C_PORT10_QUEUE4_TYPE_OFFSET    4
-#define    RTL8367C_PORT10_QUEUE4_TYPE_MASK    0x10
-#define    RTL8367C_PORT10_QUEUE3_TYPE_OFFSET    3
-#define    RTL8367C_PORT10_QUEUE3_TYPE_MASK    0x8
-#define    RTL8367C_PORT10_QUEUE2_TYPE_OFFSET    2
-#define    RTL8367C_PORT10_QUEUE2_TYPE_MASK    0x4
-#define    RTL8367C_PORT10_QUEUE1_TYPE_OFFSET    1
-#define    RTL8367C_PORT10_QUEUE1_TYPE_MASK    0x2
-#define    RTL8367C_PORT10_QUEUE0_TYPE_OFFSET    0
-#define    RTL8367C_PORT10_QUEUE0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_APR_CTRL0    0x030a
-#define    RTL8367C_PORT10_APR_ENABLE_OFFSET    10
-#define    RTL8367C_PORT10_APR_ENABLE_MASK    0x400
-#define    RTL8367C_PORT9_APR_ENABLE_OFFSET    9
-#define    RTL8367C_PORT9_APR_ENABLE_MASK    0x200
-#define    RTL8367C_PORT8_APR_ENABLE_OFFSET    8
-#define    RTL8367C_PORT8_APR_ENABLE_MASK    0x100
-#define    RTL8367C_PORT7_APR_ENABLE_OFFSET    7
-#define    RTL8367C_PORT7_APR_ENABLE_MASK    0x80
-#define    RTL8367C_PORT6_APR_ENABLE_OFFSET    6
-#define    RTL8367C_PORT6_APR_ENABLE_MASK    0x40
-#define    RTL8367C_PORT5_APR_ENABLE_OFFSET    5
-#define    RTL8367C_PORT5_APR_ENABLE_MASK    0x20
-#define    RTL8367C_PORT4_APR_ENABLE_OFFSET    4
-#define    RTL8367C_PORT4_APR_ENABLE_MASK    0x10
-#define    RTL8367C_PORT3_APR_ENABLE_OFFSET    3
-#define    RTL8367C_PORT3_APR_ENABLE_MASK    0x8
-#define    RTL8367C_PORT2_APR_ENABLE_OFFSET    2
-#define    RTL8367C_PORT2_APR_ENABLE_MASK    0x4
-#define    RTL8367C_PORT1_APR_ENABLE_OFFSET    1
-#define    RTL8367C_PORT1_APR_ENABLE_MASK    0x2
-#define    RTL8367C_PORT0_APR_ENABLE_OFFSET    0
-#define    RTL8367C_PORT0_APR_ENABLE_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE0_WFQ_WEIGHT    0x030c
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE1_WFQ_WEIGHT    0x030d
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE2_WFQ_WEIGHT    0x030e
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE3_WFQ_WEIGHT    0x030f
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE4_WFQ_WEIGHT    0x0310
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE5_WFQ_WEIGHT    0x0311
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE6_WFQ_WEIGHT    0x0312
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_QUEUE7_WFQ_WEIGHT    0x0313
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE0_WFQ_WEIGHT    0x0314
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE1_WFQ_WEIGHT    0x0315
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE2_WFQ_WEIGHT    0x0316
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE3_WFQ_WEIGHT    0x0317
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE4_WFQ_WEIGHT    0x0318
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE5_WFQ_WEIGHT    0x0319
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE6_WFQ_WEIGHT    0x031a
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_QUEUE7_WFQ_WEIGHT    0x031b
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE0_WFQ_WEIGHT    0x031c
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE1_WFQ_WEIGHT    0x031d
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE2_WFQ_WEIGHT    0x031e
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE3_WFQ_WEIGHT    0x031f
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE4_WFQ_WEIGHT    0x0320
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE5_WFQ_WEIGHT    0x0321
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE6_WFQ_WEIGHT    0x0322
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_QUEUE7_WFQ_WEIGHT    0x0323
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE0_WFQ_WEIGHT    0x0324
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE1_WFQ_WEIGHT    0x0325
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE2_WFQ_WEIGHT    0x0326
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE3_WFQ_WEIGHT    0x0327
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE4_WFQ_WEIGHT    0x0328
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE5_WFQ_WEIGHT    0x0329
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE6_WFQ_WEIGHT    0x032a
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_QUEUE7_WFQ_WEIGHT    0x032b
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE0_WFQ_WEIGHT    0x032c
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE1_WFQ_WEIGHT    0x032d
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE2_WFQ_WEIGHT    0x032e
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE3_WFQ_WEIGHT    0x032f
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE4_WFQ_WEIGHT    0x0330
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE5_WFQ_WEIGHT    0x0331
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE6_WFQ_WEIGHT    0x0332
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_QUEUE7_WFQ_WEIGHT    0x0333
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE0_WFQ_WEIGHT    0x0334
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE1_WFQ_WEIGHT    0x0335
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE2_WFQ_WEIGHT    0x0336
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE3_WFQ_WEIGHT    0x0337
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE4_WFQ_WEIGHT    0x0338
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE5_WFQ_WEIGHT    0x0339
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE6_WFQ_WEIGHT    0x033a
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_QUEUE7_WFQ_WEIGHT    0x033b
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE0_WFQ_WEIGHT    0x033c
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE1_WFQ_WEIGHT    0x033d
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE2_WFQ_WEIGHT    0x033e
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE3_WFQ_WEIGHT    0x033f
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE4_WFQ_WEIGHT    0x0340
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE5_WFQ_WEIGHT    0x0341
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE6_WFQ_WEIGHT    0x0342
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_QUEUE7_WFQ_WEIGHT    0x0343
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE0_WFQ_WEIGHT    0x0344
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE1_WFQ_WEIGHT    0x0345
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE2_WFQ_WEIGHT    0x0346
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE3_WFQ_WEIGHT    0x0347
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE4_WFQ_WEIGHT    0x0348
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE5_WFQ_WEIGHT    0x0349
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE6_WFQ_WEIGHT    0x034a
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_QUEUE7_WFQ_WEIGHT    0x034b
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE0_WFQ_WEIGHT    0x034c
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE1_WFQ_WEIGHT    0x034d
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE2_WFQ_WEIGHT    0x034e
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE3_WFQ_WEIGHT    0x034f
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE4_WFQ_WEIGHT    0x0350
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE5_WFQ_WEIGHT    0x0351
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE6_WFQ_WEIGHT    0x0352
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_QUEUE7_WFQ_WEIGHT    0x0353
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE0_WFQ_WEIGHT    0x0354
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE1_WFQ_WEIGHT    0x0355
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE2_WFQ_WEIGHT    0x0356
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE3_WFQ_WEIGHT    0x0357
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE4_WFQ_WEIGHT    0x0358
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE5_WFQ_WEIGHT    0x0359
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE6_WFQ_WEIGHT    0x035a
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_QUEUE7_WFQ_WEIGHT    0x035b
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE0_WFQ_WEIGHT    0x035c
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE1_WFQ_WEIGHT    0x035d
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE1_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE1_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE2_WFQ_WEIGHT    0x035e
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE2_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE2_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE3_WFQ_WEIGHT    0x035f
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE3_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE3_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE4_WFQ_WEIGHT    0x0360
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE4_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE4_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE5_WFQ_WEIGHT    0x0361
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE5_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE5_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE6_WFQ_WEIGHT    0x0362
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE6_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE6_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_QUEUE7_WFQ_WEIGHT    0x0363
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE7_WFQ_WEIGHT_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_QUEUE7_WFQ_WEIGHT_MASK    0x7F
-
-#define    RTL8367C_REG_PORT0_EGRESSBW_CTRL0    0x038c
-
-#define    RTL8367C_REG_PORT0_EGRESSBW_CTRL1    0x038d
-#define    RTL8367C_PORT0_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT0_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT1_EGRESSBW_CTRL0    0x038e
-
-#define    RTL8367C_REG_PORT1_EGRESSBW_CTRL1    0x038f
-#define    RTL8367C_PORT1_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT1_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT2_EGRESSBW_CTRL0    0x0390
-
-#define    RTL8367C_REG_PORT2_EGRESSBW_CTRL1    0x0391
-#define    RTL8367C_PORT2_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT2_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT3_EGRESSBW_CTRL0    0x0392
-
-#define    RTL8367C_REG_PORT3_EGRESSBW_CTRL1    0x0393
-#define    RTL8367C_PORT3_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT3_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT4_EGRESSBW_CTRL0    0x0394
-
-#define    RTL8367C_REG_PORT4_EGRESSBW_CTRL1    0x0395
-#define    RTL8367C_PORT4_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT4_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT5_EGRESSBW_CTRL0    0x0396
-
-#define    RTL8367C_REG_PORT5_EGRESSBW_CTRL1    0x0397
-#define    RTL8367C_PORT5_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT5_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT6_EGRESSBW_CTRL0    0x0398
-
-#define    RTL8367C_REG_PORT6_EGRESSBW_CTRL1    0x0399
-#define    RTL8367C_PORT6_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT6_EGRESSBW_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_PORT7_EGRESSBW_CTRL0    0x039a
-
-#define    RTL8367C_REG_PORT7_EGRESSBW_CTRL1    0x039b
-#define    RTL8367C_PORT7_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT7_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT8_EGRESSBW_CTRL0    0x039c
-
-#define    RTL8367C_REG_PORT8_EGRESSBW_CTRL1    0x039d
-#define    RTL8367C_PORT8_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT8_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_PORT9_EGRESSBW_CTRL0    0x039e
-
-#define    RTL8367C_REG_PORT9_EGRESSBW_CTRL1    0x039f
-#define    RTL8367C_PORT9_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT9_EGRESSBW_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_PORT10_EGRESSBW_CTRL0    0x03a0
-
-#define    RTL8367C_REG_PORT10_EGRESSBW_CTRL1    0x03a1
-#define    RTL8367C_PORT10_EGRESSBW_CTRL1_OFFSET    0
-#define    RTL8367C_PORT10_EGRESSBW_CTRL1_MASK    0x1
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_APR_METER_CTRL0    0x03ac
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT0_APR_METER_CTRL1    0x03ad
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT0_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_APR_METER_CTRL0    0x03b0
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT1_APR_METER_CTRL1    0x03b1
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT1_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_APR_METER_CTRL0    0x03b4
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT2_APR_METER_CTRL1    0x03b5
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT2_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_APR_METER_CTRL0    0x03b8
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT3_APR_METER_CTRL1    0x03b9
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT3_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_APR_METER_CTRL0    0x03bc
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT4_APR_METER_CTRL1    0x03bd
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT4_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_APR_METER_CTRL0    0x03c0
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT5_APR_METER_CTRL1    0x03c1
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT5_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_APR_METER_CTRL0    0x03c4
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT6_APR_METER_CTRL1    0x03c5
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT6_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_APR_METER_CTRL0    0x03c8
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT7_APR_METER_CTRL1    0x03c9
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT7_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_APR_METER_CTRL0    0x03ca
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT8_APR_METER_CTRL1    0x03cb
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT8_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_APR_METER_CTRL0    0x03cc
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT9_APR_METER_CTRL1    0x03cd
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT9_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_APR_METER_CTRL0    0x03ce
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE4_APR_METER_OFFSET    12
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE4_APR_METER_MASK    0x7000
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE3_APR_METER_OFFSET    9
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE3_APR_METER_MASK    0xE00
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE2_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE2_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE1_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE1_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE0_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL0_QUEUE0_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_SCHEDULE_PORT10_APR_METER_CTRL1    0x03cf
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL1_QUEUE7_APR_METER_OFFSET    6
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL1_QUEUE7_APR_METER_MASK    0x1C0
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL1_QUEUE6_APR_METER_OFFSET    3
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL1_QUEUE6_APR_METER_MASK    0x38
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL1_QUEUE5_APR_METER_OFFSET    0
-#define    RTL8367C_SCHEDULE_PORT10_APR_METER_CTRL1_QUEUE5_APR_METER_MASK    0x7
-
-#define    RTL8367C_REG_LINE_RATE_1G_L    0x03ec
-
-#define    RTL8367C_REG_LINE_RATE_1G_H    0x03ed
-#define    RTL8367C_LINE_RATE_1G_H_OFFSET    0
-#define    RTL8367C_LINE_RATE_1G_H_MASK    0x1
-
-#define    RTL8367C_REG_LINE_RATE_100_L    0x03ee
-
-#define    RTL8367C_REG_LINE_RATE_100_H    0x03ef
-#define    RTL8367C_LINE_RATE_100_H_OFFSET    0
-#define    RTL8367C_LINE_RATE_100_H_MASK    0x1
-
-#define    RTL8367C_REG_LINE_RATE_10_L    0x03f0
-
-#define    RTL8367C_REG_LINE_RATE_10_H    0x03f1
-#define    RTL8367C_LINE_RATE_10_H_OFFSET    0
-#define    RTL8367C_LINE_RATE_10_H_MASK    0x1
-
-#define    RTL8367C_REG_DUMMY_03f2    0x03f2
-
-#define    RTL8367C_REG_DUMMY_03f3    0x03f3
-
-#define    RTL8367C_REG_DUMMY_03f4    0x03f4
-
-#define    RTL8367C_REG_DUMMY_03f5    0x03f5
-
-#define    RTL8367C_REG_DUMMY_03f6    0x03f6
-
-#define    RTL8367C_REG_BYPASS_LINE_RATE    0x03f7
-#define    RTL8367C_BYPASS_PORT10_CONSTRAINT_OFFSET    5
-#define    RTL8367C_BYPASS_PORT10_CONSTRAINT_MASK    0x20
-#define    RTL8367C_BYPASS_PORT9_CONSTRAINT_OFFSET    4
-#define    RTL8367C_BYPASS_PORT9_CONSTRAINT_MASK    0x10
-#define    RTL8367C_BYPASS_PORT8_CONSTRAINT_OFFSET    3
-#define    RTL8367C_BYPASS_PORT8_CONSTRAINT_MASK    0x8
-#define    RTL8367C_BYPASS_PORT7_CONSTRAINT_OFFSET    2
-#define    RTL8367C_BYPASS_PORT7_CONSTRAINT_MASK    0x4
-#define    RTL8367C_BYPASS_PORT6_CONSTRAINT_OFFSET    1
-#define    RTL8367C_BYPASS_PORT6_CONSTRAINT_MASK    0x2
-#define    RTL8367C_BYPASS_PORT5_CONSTRAINT_OFFSET    0
-#define    RTL8367C_BYPASS_PORT5_CONSTRAINT_MASK    0x1
-
-#define    RTL8367C_REG_LINE_RATE_500_H    0x03f8
-#define    RTL8367C_LINE_RATE_500_H_OFFSET    0
-#define    RTL8367C_LINE_RATE_500_H_MASK    0x7
-
-#define    RTL8367C_REG_LINE_RATE_500_L    0x03f9
-
-#define    RTL8367C_REG_LINE_RATE_HSG_H    0x03fa
-#define    RTL8367C_LINE_RATE_HSG_H_OFFSET    0
-#define    RTL8367C_LINE_RATE_HSG_H_MASK    0x7
-
-#define    RTL8367C_REG_LINE_RATE_HSG_L    0x03fb
-
-/* (16'h0500)table_reg */
-
-#define    RTL8367C_REG_TABLE_ACCESS_CTRL    0x0500
-#define    RTL8367C_TABLE_ACCESS_CTRL_SPA_OFFSET    8
-#define    RTL8367C_TABLE_ACCESS_CTRL_SPA_MASK    0xF00
-#define    RTL8367C_ACCESS_METHOD_OFFSET    4
-#define    RTL8367C_ACCESS_METHOD_MASK    0x70
-#define    RTL8367C_COMMAND_TYPE_OFFSET    3
-#define    RTL8367C_COMMAND_TYPE_MASK    0x8
-#define    RTL8367C_TABLE_TYPE_OFFSET    0
-#define    RTL8367C_TABLE_TYPE_MASK    0x7
-
-#define    RTL8367C_REG_TABLE_ACCESS_ADDR    0x0501
-#define    RTL8367C_TABLE_ACCESS_ADDR_OFFSET    0
-#define    RTL8367C_TABLE_ACCESS_ADDR_MASK    0x1FFF
-
-#define    RTL8367C_REG_TABLE_LUT_ADDR    0x0502
-#define    RTL8367C_ADDRESS2_OFFSET    14
-#define    RTL8367C_ADDRESS2_MASK    0x4000
-#define    RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_OFFSET    13
-#define    RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_MASK    0x2000
-#define    RTL8367C_HIT_STATUS_OFFSET    12
-#define    RTL8367C_HIT_STATUS_MASK    0x1000
-#define    RTL8367C_TABLE_LUT_ADDR_TYPE_OFFSET    11
-#define    RTL8367C_TABLE_LUT_ADDR_TYPE_MASK    0x800
-#define    RTL8367C_TABLE_LUT_ADDR_ADDRESS_OFFSET    0
-#define    RTL8367C_TABLE_LUT_ADDR_ADDRESS_MASK    0x7FF
-
-#define    RTL8367C_REG_HSA_HSB_LATCH    0x0503
-#define    RTL8367C_LATCH_ALWAYS_OFFSET    15
-#define    RTL8367C_LATCH_ALWAYS_MASK    0x8000
-#define    RTL8367C_LATCH_FIRST_OFFSET    14
-#define    RTL8367C_LATCH_FIRST_MASK    0x4000
-#define    RTL8367C_SPA_EN_OFFSET    13
-#define    RTL8367C_SPA_EN_MASK    0x2000
-#define    RTL8367C_FORWARD_EN_OFFSET    12
-#define    RTL8367C_FORWARD_EN_MASK    0x1000
-#define    RTL8367C_REASON_EN_OFFSET    11
-#define    RTL8367C_REASON_EN_MASK    0x800
-#define    RTL8367C_HSA_HSB_LATCH_SPA_OFFSET    8
-#define    RTL8367C_HSA_HSB_LATCH_SPA_MASK    0x700
-#define    RTL8367C_FORWARD_OFFSET    6
-#define    RTL8367C_FORWARD_MASK    0xC0
-#define    RTL8367C_REASON_OFFSET    0
-#define    RTL8367C_REASON_MASK    0x3F
-
-#define    RTL8367C_REG_HSA_HSB_LATCH2    0x0504
-#define    RTL8367C_HSA_HSB_LATCH2_Reserved_OFFSET    1
-#define    RTL8367C_HSA_HSB_LATCH2_Reserved_MASK    0xFFFE
-#define    RTL8367C_SPA2_OFFSET    0
-#define    RTL8367C_SPA2_MASK    0x1
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA0    0x0510
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA1    0x0511
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA2    0x0512
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA3    0x0513
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA4    0x0514
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA5    0x0515
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA6    0x0516
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA7    0x0517
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA8    0x0518
-
-#define    RTL8367C_REG_TABLE_WRITE_DATA9    0x0519
-#define    RTL8367C_TABLE_WRITE_DATA9_OFFSET    0
-#define    RTL8367C_TABLE_WRITE_DATA9_MASK    0xF
-
-#define    RTL8367C_REG_TABLE_READ_DATA0    0x0520
-
-#define    RTL8367C_REG_TABLE_READ_DATA1    0x0521
-
-#define    RTL8367C_REG_TABLE_READ_DATA2    0x0522
-
-#define    RTL8367C_REG_TABLE_READ_DATA3    0x0523
-
-#define    RTL8367C_REG_TABLE_READ_DATA4    0x0524
-
-#define    RTL8367C_REG_TABLE_READ_DATA5    0x0525
-
-#define    RTL8367C_REG_TABLE_READ_DATA6    0x0526
-
-#define    RTL8367C_REG_TABLE_READ_DATA7    0x0527
-
-#define    RTL8367C_REG_TABLE_READ_DATA8    0x0528
-
-#define    RTL8367C_REG_TABLE_READ_DATA9    0x0529
-#define    RTL8367C_TABLE_READ_DATA9_OFFSET    0
-#define    RTL8367C_TABLE_READ_DATA9_MASK    0xF
-
-#define    RTL8367C_REG_TBL_DUMMY00    0x0550
-
-#define    RTL8367C_REG_TBL_DUMMY01    0x0551
-
-/* (16'h0600)acl_reg */
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE0_CTRL0    0x0600
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL0_FIELD1_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL0_FIELD1_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL0_FIELD0_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL0_FIELD0_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE0_CTRL1    0x0601
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL1_FIELD3_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL1_FIELD3_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL1_FIELD2_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL1_FIELD2_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE0_CTRL2    0x0602
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL2_FIELD5_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL2_FIELD5_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL2_FIELD4_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL2_FIELD4_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE0_CTRL3    0x0603
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL3_FIELD7_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL3_FIELD7_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL3_FIELD6_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE0_CTRL3_FIELD6_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE1_CTRL0    0x0604
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL0_FIELD1_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL0_FIELD1_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL0_FIELD0_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL0_FIELD0_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE1_CTRL1    0x0605
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL1_FIELD3_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL1_FIELD3_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL1_FIELD2_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL1_FIELD2_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE1_CTRL2    0x0606
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL2_FIELD5_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL2_FIELD5_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL2_FIELD4_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL2_FIELD4_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE1_CTRL3    0x0607
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL3_FIELD7_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL3_FIELD7_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL3_FIELD6_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE1_CTRL3_FIELD6_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE2_CTRL0    0x0608
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL0_FIELD1_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL0_FIELD1_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL0_FIELD0_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL0_FIELD0_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE2_CTRL1    0x0609
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL1_FIELD3_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL1_FIELD3_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL1_FIELD2_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL1_FIELD2_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE2_CTRL2    0x060a
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL2_FIELD5_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL2_FIELD5_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL2_FIELD4_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL2_FIELD4_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE2_CTRL3    0x060b
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL3_FIELD7_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL3_FIELD7_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL3_FIELD6_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE2_CTRL3_FIELD6_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE3_CTRL0    0x060c
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL0_FIELD1_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL0_FIELD1_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL0_FIELD0_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL0_FIELD0_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE3_CTRL1    0x060d
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL1_FIELD3_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL1_FIELD3_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL1_FIELD2_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL1_FIELD2_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE3_CTRL2    0x060e
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL2_FIELD5_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL2_FIELD5_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL2_FIELD4_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL2_FIELD4_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE3_CTRL3    0x060f
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL3_FIELD7_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL3_FIELD7_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL3_FIELD6_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE3_CTRL3_FIELD6_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE4_CTRL0    0x0610
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL0_FIELD1_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL0_FIELD1_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL0_FIELD0_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL0_FIELD0_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE4_CTRL1    0x0611
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL1_FIELD3_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL1_FIELD3_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL1_FIELD2_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL1_FIELD2_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE4_CTRL2    0x0612
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL2_FIELD5_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL2_FIELD5_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL2_FIELD4_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL2_FIELD4_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_RULE_TEMPLATE4_CTRL3    0x0613
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL3_FIELD7_OFFSET    8
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL3_FIELD7_MASK    0x7F00
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL3_FIELD6_OFFSET    0
-#define    RTL8367C_ACL_RULE_TEMPLATE4_CTRL3_FIELD6_MASK    0x7F
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL0    0x0614
-#define    RTL8367C_OP1_NOT_OFFSET    14
-#define    RTL8367C_OP1_NOT_MASK    0x4000
-#define    RTL8367C_ACT1_GPIO_OFFSET    13
-#define    RTL8367C_ACT1_GPIO_MASK    0x2000
-#define    RTL8367C_ACT1_FORWARD_OFFSET    12
-#define    RTL8367C_ACT1_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT1_POLICING_OFFSET    11
-#define    RTL8367C_ACT1_POLICING_MASK    0x800
-#define    RTL8367C_ACT1_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT1_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT1_SVID_OFFSET    9
-#define    RTL8367C_ACT1_SVID_MASK    0x200
-#define    RTL8367C_ACT1_CVID_OFFSET    8
-#define    RTL8367C_ACT1_CVID_MASK    0x100
-#define    RTL8367C_OP0_NOT_OFFSET    6
-#define    RTL8367C_OP0_NOT_MASK    0x40
-#define    RTL8367C_ACT0_GPIO_OFFSET    5
-#define    RTL8367C_ACT0_GPIO_MASK    0x20
-#define    RTL8367C_ACT0_FORWARD_OFFSET    4
-#define    RTL8367C_ACT0_FORWARD_MASK    0x10
-#define    RTL8367C_ACT0_POLICING_OFFSET    3
-#define    RTL8367C_ACT0_POLICING_MASK    0x8
-#define    RTL8367C_ACT0_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT0_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT0_SVID_OFFSET    1
-#define    RTL8367C_ACT0_SVID_MASK    0x2
-#define    RTL8367C_ACT0_CVID_OFFSET    0
-#define    RTL8367C_ACT0_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL1    0x0615
-#define    RTL8367C_OP3_NOT_OFFSET    14
-#define    RTL8367C_OP3_NOT_MASK    0x4000
-#define    RTL8367C_ACT3_GPIO_OFFSET    13
-#define    RTL8367C_ACT3_GPIO_MASK    0x2000
-#define    RTL8367C_ACT3_FORWARD_OFFSET    12
-#define    RTL8367C_ACT3_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT3_POLICING_OFFSET    11
-#define    RTL8367C_ACT3_POLICING_MASK    0x800
-#define    RTL8367C_ACT3_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT3_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT3_SVID_OFFSET    9
-#define    RTL8367C_ACT3_SVID_MASK    0x200
-#define    RTL8367C_ACT3_CVID_OFFSET    8
-#define    RTL8367C_ACT3_CVID_MASK    0x100
-#define    RTL8367C_OP2_NOT_OFFSET    6
-#define    RTL8367C_OP2_NOT_MASK    0x40
-#define    RTL8367C_ACT2_GPIO_OFFSET    5
-#define    RTL8367C_ACT2_GPIO_MASK    0x20
-#define    RTL8367C_ACT2_FORWARD_OFFSET    4
-#define    RTL8367C_ACT2_FORWARD_MASK    0x10
-#define    RTL8367C_ACT2_POLICING_OFFSET    3
-#define    RTL8367C_ACT2_POLICING_MASK    0x8
-#define    RTL8367C_ACT2_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT2_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT2_SVID_OFFSET    1
-#define    RTL8367C_ACT2_SVID_MASK    0x2
-#define    RTL8367C_ACT2_CVID_OFFSET    0
-#define    RTL8367C_ACT2_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL2    0x0616
-#define    RTL8367C_OP5_NOT_OFFSET    14
-#define    RTL8367C_OP5_NOT_MASK    0x4000
-#define    RTL8367C_ACT5_GPIO_OFFSET    13
-#define    RTL8367C_ACT5_GPIO_MASK    0x2000
-#define    RTL8367C_ACT5_FORWARD_OFFSET    12
-#define    RTL8367C_ACT5_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT5_POLICING_OFFSET    11
-#define    RTL8367C_ACT5_POLICING_MASK    0x800
-#define    RTL8367C_ACT5_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT5_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT5_SVID_OFFSET    9
-#define    RTL8367C_ACT5_SVID_MASK    0x200
-#define    RTL8367C_ACT5_CVID_OFFSET    8
-#define    RTL8367C_ACT5_CVID_MASK    0x100
-#define    RTL8367C_OP4_NOT_OFFSET    6
-#define    RTL8367C_OP4_NOT_MASK    0x40
-#define    RTL8367C_ACT4_GPIO_OFFSET    5
-#define    RTL8367C_ACT4_GPIO_MASK    0x20
-#define    RTL8367C_ACT4_FORWARD_OFFSET    4
-#define    RTL8367C_ACT4_FORWARD_MASK    0x10
-#define    RTL8367C_ACT4_POLICING_OFFSET    3
-#define    RTL8367C_ACT4_POLICING_MASK    0x8
-#define    RTL8367C_ACT4_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT4_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT4_SVID_OFFSET    1
-#define    RTL8367C_ACT4_SVID_MASK    0x2
-#define    RTL8367C_ACT4_CVID_OFFSET    0
-#define    RTL8367C_ACT4_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL3    0x0617
-#define    RTL8367C_OP7_NOT_OFFSET    14
-#define    RTL8367C_OP7_NOT_MASK    0x4000
-#define    RTL8367C_ACT7_GPIO_OFFSET    13
-#define    RTL8367C_ACT7_GPIO_MASK    0x2000
-#define    RTL8367C_ACT7_FORWARD_OFFSET    12
-#define    RTL8367C_ACT7_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT7_POLICING_OFFSET    11
-#define    RTL8367C_ACT7_POLICING_MASK    0x800
-#define    RTL8367C_ACT7_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT7_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT7_SVID_OFFSET    9
-#define    RTL8367C_ACT7_SVID_MASK    0x200
-#define    RTL8367C_ACT7_CVID_OFFSET    8
-#define    RTL8367C_ACT7_CVID_MASK    0x100
-#define    RTL8367C_OP6_NOT_OFFSET    6
-#define    RTL8367C_OP6_NOT_MASK    0x40
-#define    RTL8367C_ACT6_GPIO_OFFSET    5
-#define    RTL8367C_ACT6_GPIO_MASK    0x20
-#define    RTL8367C_ACT6_FORWARD_OFFSET    4
-#define    RTL8367C_ACT6_FORWARD_MASK    0x10
-#define    RTL8367C_ACT6_POLICING_OFFSET    3
-#define    RTL8367C_ACT6_POLICING_MASK    0x8
-#define    RTL8367C_ACT6_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT6_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT6_SVID_OFFSET    1
-#define    RTL8367C_ACT6_SVID_MASK    0x2
-#define    RTL8367C_ACT6_CVID_OFFSET    0
-#define    RTL8367C_ACT6_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL4    0x0618
-#define    RTL8367C_OP9_NOT_OFFSET    14
-#define    RTL8367C_OP9_NOT_MASK    0x4000
-#define    RTL8367C_ACT9_GPIO_OFFSET    13
-#define    RTL8367C_ACT9_GPIO_MASK    0x2000
-#define    RTL8367C_ACT9_FORWARD_OFFSET    12
-#define    RTL8367C_ACT9_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT9_POLICING_OFFSET    11
-#define    RTL8367C_ACT9_POLICING_MASK    0x800
-#define    RTL8367C_ACT9_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT9_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT9_SVID_OFFSET    9
-#define    RTL8367C_ACT9_SVID_MASK    0x200
-#define    RTL8367C_ACT9_CVID_OFFSET    8
-#define    RTL8367C_ACT9_CVID_MASK    0x100
-#define    RTL8367C_OP8_NOT_OFFSET    6
-#define    RTL8367C_OP8_NOT_MASK    0x40
-#define    RTL8367C_ACT8_GPIO_OFFSET    5
-#define    RTL8367C_ACT8_GPIO_MASK    0x20
-#define    RTL8367C_ACT8_FORWARD_OFFSET    4
-#define    RTL8367C_ACT8_FORWARD_MASK    0x10
-#define    RTL8367C_ACT8_POLICING_OFFSET    3
-#define    RTL8367C_ACT8_POLICING_MASK    0x8
-#define    RTL8367C_ACT8_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT8_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT8_SVID_OFFSET    1
-#define    RTL8367C_ACT8_SVID_MASK    0x2
-#define    RTL8367C_ACT8_CVID_OFFSET    0
-#define    RTL8367C_ACT8_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL5    0x0619
-#define    RTL8367C_OP11_NOT_OFFSET    14
-#define    RTL8367C_OP11_NOT_MASK    0x4000
-#define    RTL8367C_ACT11_GPIO_OFFSET    13
-#define    RTL8367C_ACT11_GPIO_MASK    0x2000
-#define    RTL8367C_ACT11_FORWARD_OFFSET    12
-#define    RTL8367C_ACT11_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT11_POLICING_OFFSET    11
-#define    RTL8367C_ACT11_POLICING_MASK    0x800
-#define    RTL8367C_ACT11_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT11_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT11_SVID_OFFSET    9
-#define    RTL8367C_ACT11_SVID_MASK    0x200
-#define    RTL8367C_ACT11_CVID_OFFSET    8
-#define    RTL8367C_ACT11_CVID_MASK    0x100
-#define    RTL8367C_OP10_NOT_OFFSET    6
-#define    RTL8367C_OP10_NOT_MASK    0x40
-#define    RTL8367C_ACT10_GPIO_OFFSET    5
-#define    RTL8367C_ACT10_GPIO_MASK    0x20
-#define    RTL8367C_ACT10_FORWARD_OFFSET    4
-#define    RTL8367C_ACT10_FORWARD_MASK    0x10
-#define    RTL8367C_ACT10_POLICING_OFFSET    3
-#define    RTL8367C_ACT10_POLICING_MASK    0x8
-#define    RTL8367C_ACT10_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT10_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT10_SVID_OFFSET    1
-#define    RTL8367C_ACT10_SVID_MASK    0x2
-#define    RTL8367C_ACT10_CVID_OFFSET    0
-#define    RTL8367C_ACT10_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL6    0x061a
-#define    RTL8367C_OP13_NOT_OFFSET    14
-#define    RTL8367C_OP13_NOT_MASK    0x4000
-#define    RTL8367C_ACT13_GPIO_OFFSET    13
-#define    RTL8367C_ACT13_GPIO_MASK    0x2000
-#define    RTL8367C_ACT13_FORWARD_OFFSET    12
-#define    RTL8367C_ACT13_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT13_POLICING_OFFSET    11
-#define    RTL8367C_ACT13_POLICING_MASK    0x800
-#define    RTL8367C_ACT13_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT13_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT13_SVID_OFFSET    9
-#define    RTL8367C_ACT13_SVID_MASK    0x200
-#define    RTL8367C_ACT13_CVID_OFFSET    8
-#define    RTL8367C_ACT13_CVID_MASK    0x100
-#define    RTL8367C_OP12_NOT_OFFSET    6
-#define    RTL8367C_OP12_NOT_MASK    0x40
-#define    RTL8367C_ACT12_GPIO_OFFSET    5
-#define    RTL8367C_ACT12_GPIO_MASK    0x20
-#define    RTL8367C_ACT12_FORWARD_OFFSET    4
-#define    RTL8367C_ACT12_FORWARD_MASK    0x10
-#define    RTL8367C_ACT12_POLICING_OFFSET    3
-#define    RTL8367C_ACT12_POLICING_MASK    0x8
-#define    RTL8367C_ACT12_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT12_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT12_SVID_OFFSET    1
-#define    RTL8367C_ACT12_SVID_MASK    0x2
-#define    RTL8367C_ACT12_CVID_OFFSET    0
-#define    RTL8367C_ACT12_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL7    0x061b
-#define    RTL8367C_OP15_NOT_OFFSET    14
-#define    RTL8367C_OP15_NOT_MASK    0x4000
-#define    RTL8367C_ACT15_GPIO_OFFSET    13
-#define    RTL8367C_ACT15_GPIO_MASK    0x2000
-#define    RTL8367C_ACT15_FORWARD_OFFSET    12
-#define    RTL8367C_ACT15_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT15_POLICING_OFFSET    11
-#define    RTL8367C_ACT15_POLICING_MASK    0x800
-#define    RTL8367C_ACT15_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT15_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT15_SVID_OFFSET    9
-#define    RTL8367C_ACT15_SVID_MASK    0x200
-#define    RTL8367C_ACT15_CVID_OFFSET    8
-#define    RTL8367C_ACT15_CVID_MASK    0x100
-#define    RTL8367C_OP14_NOT_OFFSET    6
-#define    RTL8367C_OP14_NOT_MASK    0x40
-#define    RTL8367C_ACT14_GPIO_OFFSET    5
-#define    RTL8367C_ACT14_GPIO_MASK    0x20
-#define    RTL8367C_ACT14_FORWARD_OFFSET    4
-#define    RTL8367C_ACT14_FORWARD_MASK    0x10
-#define    RTL8367C_ACT14_POLICING_OFFSET    3
-#define    RTL8367C_ACT14_POLICING_MASK    0x8
-#define    RTL8367C_ACT14_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT14_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT14_SVID_OFFSET    1
-#define    RTL8367C_ACT14_SVID_MASK    0x2
-#define    RTL8367C_ACT14_CVID_OFFSET    0
-#define    RTL8367C_ACT14_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL8    0x061c
-#define    RTL8367C_OP17_NOT_OFFSET    14
-#define    RTL8367C_OP17_NOT_MASK    0x4000
-#define    RTL8367C_ACT17_GPIO_OFFSET    13
-#define    RTL8367C_ACT17_GPIO_MASK    0x2000
-#define    RTL8367C_ACT17_FORWARD_OFFSET    12
-#define    RTL8367C_ACT17_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT17_POLICING_OFFSET    11
-#define    RTL8367C_ACT17_POLICING_MASK    0x800
-#define    RTL8367C_ACT17_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT17_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT17_SVID_OFFSET    9
-#define    RTL8367C_ACT17_SVID_MASK    0x200
-#define    RTL8367C_ACT17_CVID_OFFSET    8
-#define    RTL8367C_ACT17_CVID_MASK    0x100
-#define    RTL8367C_OP16_NOT_OFFSET    6
-#define    RTL8367C_OP16_NOT_MASK    0x40
-#define    RTL8367C_ACT16_GPIO_OFFSET    5
-#define    RTL8367C_ACT16_GPIO_MASK    0x20
-#define    RTL8367C_ACT16_FORWARD_OFFSET    4
-#define    RTL8367C_ACT16_FORWARD_MASK    0x10
-#define    RTL8367C_ACT16_POLICING_OFFSET    3
-#define    RTL8367C_ACT16_POLICING_MASK    0x8
-#define    RTL8367C_ACT16_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT16_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT16_SVID_OFFSET    1
-#define    RTL8367C_ACT16_SVID_MASK    0x2
-#define    RTL8367C_ACT16_CVID_OFFSET    0
-#define    RTL8367C_ACT16_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL9    0x061d
-#define    RTL8367C_OP19_NOT_OFFSET    14
-#define    RTL8367C_OP19_NOT_MASK    0x4000
-#define    RTL8367C_ACT19_GPIO_OFFSET    13
-#define    RTL8367C_ACT19_GPIO_MASK    0x2000
-#define    RTL8367C_ACT19_FORWARD_OFFSET    12
-#define    RTL8367C_ACT19_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT19_POLICING_OFFSET    11
-#define    RTL8367C_ACT19_POLICING_MASK    0x800
-#define    RTL8367C_ACT19_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT19_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT19_SVID_OFFSET    9
-#define    RTL8367C_ACT19_SVID_MASK    0x200
-#define    RTL8367C_ACT19_CVID_OFFSET    8
-#define    RTL8367C_ACT19_CVID_MASK    0x100
-#define    RTL8367C_OP18_NOT_OFFSET    6
-#define    RTL8367C_OP18_NOT_MASK    0x40
-#define    RTL8367C_ACT18_GPIO_OFFSET    5
-#define    RTL8367C_ACT18_GPIO_MASK    0x20
-#define    RTL8367C_ACT18_FORWARD_OFFSET    4
-#define    RTL8367C_ACT18_FORWARD_MASK    0x10
-#define    RTL8367C_ACT18_POLICING_OFFSET    3
-#define    RTL8367C_ACT18_POLICING_MASK    0x8
-#define    RTL8367C_ACT18_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT18_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT18_SVID_OFFSET    1
-#define    RTL8367C_ACT18_SVID_MASK    0x2
-#define    RTL8367C_ACT18_CVID_OFFSET    0
-#define    RTL8367C_ACT18_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL10    0x061e
-#define    RTL8367C_OP21_NOT_OFFSET    14
-#define    RTL8367C_OP21_NOT_MASK    0x4000
-#define    RTL8367C_ACT21_GPIO_OFFSET    13
-#define    RTL8367C_ACT21_GPIO_MASK    0x2000
-#define    RTL8367C_ACT21_FORWARD_OFFSET    12
-#define    RTL8367C_ACT21_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT21_POLICING_OFFSET    11
-#define    RTL8367C_ACT21_POLICING_MASK    0x800
-#define    RTL8367C_ACT21_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT21_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT21_SVID_OFFSET    9
-#define    RTL8367C_ACT21_SVID_MASK    0x200
-#define    RTL8367C_ACT21_CVID_OFFSET    8
-#define    RTL8367C_ACT21_CVID_MASK    0x100
-#define    RTL8367C_OP20_NOT_OFFSET    6
-#define    RTL8367C_OP20_NOT_MASK    0x40
-#define    RTL8367C_ACT20_GPIO_OFFSET    5
-#define    RTL8367C_ACT20_GPIO_MASK    0x20
-#define    RTL8367C_ACT20_FORWARD_OFFSET    4
-#define    RTL8367C_ACT20_FORWARD_MASK    0x10
-#define    RTL8367C_ACT20_POLICING_OFFSET    3
-#define    RTL8367C_ACT20_POLICING_MASK    0x8
-#define    RTL8367C_ACT20_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT20_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT20_SVID_OFFSET    1
-#define    RTL8367C_ACT20_SVID_MASK    0x2
-#define    RTL8367C_ACT20_CVID_OFFSET    0
-#define    RTL8367C_ACT20_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL11    0x061f
-#define    RTL8367C_OP23_NOT_OFFSET    14
-#define    RTL8367C_OP23_NOT_MASK    0x4000
-#define    RTL8367C_ACT23_GPIO_OFFSET    13
-#define    RTL8367C_ACT23_GPIO_MASK    0x2000
-#define    RTL8367C_ACT23_FORWARD_OFFSET    12
-#define    RTL8367C_ACT23_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT23_POLICING_OFFSET    11
-#define    RTL8367C_ACT23_POLICING_MASK    0x800
-#define    RTL8367C_ACT23_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT23_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT23_SVID_OFFSET    9
-#define    RTL8367C_ACT23_SVID_MASK    0x200
-#define    RTL8367C_ACT23_CVID_OFFSET    8
-#define    RTL8367C_ACT23_CVID_MASK    0x100
-#define    RTL8367C_OP22_NOT_OFFSET    6
-#define    RTL8367C_OP22_NOT_MASK    0x40
-#define    RTL8367C_ACT22_GPIO_OFFSET    5
-#define    RTL8367C_ACT22_GPIO_MASK    0x20
-#define    RTL8367C_ACT22_FORWARD_OFFSET    4
-#define    RTL8367C_ACT22_FORWARD_MASK    0x10
-#define    RTL8367C_ACT22_POLICING_OFFSET    3
-#define    RTL8367C_ACT22_POLICING_MASK    0x8
-#define    RTL8367C_ACT22_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT22_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT22_SVID_OFFSET    1
-#define    RTL8367C_ACT22_SVID_MASK    0x2
-#define    RTL8367C_ACT22_CVID_OFFSET    0
-#define    RTL8367C_ACT22_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL12    0x0620
-#define    RTL8367C_OP25_NOT_OFFSET    14
-#define    RTL8367C_OP25_NOT_MASK    0x4000
-#define    RTL8367C_ACT25_GPIO_OFFSET    13
-#define    RTL8367C_ACT25_GPIO_MASK    0x2000
-#define    RTL8367C_ACT25_FORWARD_OFFSET    12
-#define    RTL8367C_ACT25_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT25_POLICING_OFFSET    11
-#define    RTL8367C_ACT25_POLICING_MASK    0x800
-#define    RTL8367C_ACT25_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT25_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT25_SVID_OFFSET    9
-#define    RTL8367C_ACT25_SVID_MASK    0x200
-#define    RTL8367C_ACT25_CVID_OFFSET    8
-#define    RTL8367C_ACT25_CVID_MASK    0x100
-#define    RTL8367C_OP24_NOT_OFFSET    6
-#define    RTL8367C_OP24_NOT_MASK    0x40
-#define    RTL8367C_ACT24_GPIO_OFFSET    5
-#define    RTL8367C_ACT24_GPIO_MASK    0x20
-#define    RTL8367C_ACT24_FORWARD_OFFSET    4
-#define    RTL8367C_ACT24_FORWARD_MASK    0x10
-#define    RTL8367C_ACT24_POLICING_OFFSET    3
-#define    RTL8367C_ACT24_POLICING_MASK    0x8
-#define    RTL8367C_ACT24_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT24_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT24_SVID_OFFSET    1
-#define    RTL8367C_ACT24_SVID_MASK    0x2
-#define    RTL8367C_ACT24_CVID_OFFSET    0
-#define    RTL8367C_ACT24_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL13    0x0621
-#define    RTL8367C_OP27_NOT_OFFSET    14
-#define    RTL8367C_OP27_NOT_MASK    0x4000
-#define    RTL8367C_ACT27_GPIO_OFFSET    13
-#define    RTL8367C_ACT27_GPIO_MASK    0x2000
-#define    RTL8367C_ACT27_FORWARD_OFFSET    12
-#define    RTL8367C_ACT27_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT27_POLICING_OFFSET    11
-#define    RTL8367C_ACT27_POLICING_MASK    0x800
-#define    RTL8367C_ACT27_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT27_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT27_SVID_OFFSET    9
-#define    RTL8367C_ACT27_SVID_MASK    0x200
-#define    RTL8367C_ACT27_CVID_OFFSET    8
-#define    RTL8367C_ACT27_CVID_MASK    0x100
-#define    RTL8367C_OP26_NOT_OFFSET    6
-#define    RTL8367C_OP26_NOT_MASK    0x40
-#define    RTL8367C_ACT26_GPIO_OFFSET    5
-#define    RTL8367C_ACT26_GPIO_MASK    0x20
-#define    RTL8367C_ACT26_FORWARD_OFFSET    4
-#define    RTL8367C_ACT26_FORWARD_MASK    0x10
-#define    RTL8367C_ACT26_POLICING_OFFSET    3
-#define    RTL8367C_ACT26_POLICING_MASK    0x8
-#define    RTL8367C_ACT26_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT26_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT26_SVID_OFFSET    1
-#define    RTL8367C_ACT26_SVID_MASK    0x2
-#define    RTL8367C_ACT26_CVID_OFFSET    0
-#define    RTL8367C_ACT26_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL14    0x0622
-#define    RTL8367C_OP29_NOT_OFFSET    14
-#define    RTL8367C_OP29_NOT_MASK    0x4000
-#define    RTL8367C_ACT29_GPIO_OFFSET    13
-#define    RTL8367C_ACT29_GPIO_MASK    0x2000
-#define    RTL8367C_ACT29_FORWARD_OFFSET    12
-#define    RTL8367C_ACT29_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT29_POLICING_OFFSET    11
-#define    RTL8367C_ACT29_POLICING_MASK    0x800
-#define    RTL8367C_ACT29_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT29_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT29_SVID_OFFSET    9
-#define    RTL8367C_ACT29_SVID_MASK    0x200
-#define    RTL8367C_ACT29_CVID_OFFSET    8
-#define    RTL8367C_ACT29_CVID_MASK    0x100
-#define    RTL8367C_OP28_NOT_OFFSET    6
-#define    RTL8367C_OP28_NOT_MASK    0x40
-#define    RTL8367C_ACT28_GPIO_OFFSET    5
-#define    RTL8367C_ACT28_GPIO_MASK    0x20
-#define    RTL8367C_ACT28_FORWARD_OFFSET    4
-#define    RTL8367C_ACT28_FORWARD_MASK    0x10
-#define    RTL8367C_ACT28_POLICING_OFFSET    3
-#define    RTL8367C_ACT28_POLICING_MASK    0x8
-#define    RTL8367C_ACT28_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT28_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT28_SVID_OFFSET    1
-#define    RTL8367C_ACT28_SVID_MASK    0x2
-#define    RTL8367C_ACT28_CVID_OFFSET    0
-#define    RTL8367C_ACT28_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL15    0x0623
-#define    RTL8367C_OP31_NOT_OFFSET    14
-#define    RTL8367C_OP31_NOT_MASK    0x4000
-#define    RTL8367C_ACT31_GPIO_OFFSET    13
-#define    RTL8367C_ACT31_GPIO_MASK    0x2000
-#define    RTL8367C_ACT31_FORWARD_OFFSET    12
-#define    RTL8367C_ACT31_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT31_POLICING_OFFSET    11
-#define    RTL8367C_ACT31_POLICING_MASK    0x800
-#define    RTL8367C_ACT31_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT31_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT31_SVID_OFFSET    9
-#define    RTL8367C_ACT31_SVID_MASK    0x200
-#define    RTL8367C_ACT31_CVID_OFFSET    8
-#define    RTL8367C_ACT31_CVID_MASK    0x100
-#define    RTL8367C_OP30_NOT_OFFSET    6
-#define    RTL8367C_OP30_NOT_MASK    0x40
-#define    RTL8367C_ACT30_GPIO_OFFSET    5
-#define    RTL8367C_ACT30_GPIO_MASK    0x20
-#define    RTL8367C_ACT30_FORWARD_OFFSET    4
-#define    RTL8367C_ACT30_FORWARD_MASK    0x10
-#define    RTL8367C_ACT30_POLICING_OFFSET    3
-#define    RTL8367C_ACT30_POLICING_MASK    0x8
-#define    RTL8367C_ACT30_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT30_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT30_SVID_OFFSET    1
-#define    RTL8367C_ACT30_SVID_MASK    0x2
-#define    RTL8367C_ACT30_CVID_OFFSET    0
-#define    RTL8367C_ACT30_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL16    0x0624
-#define    RTL8367C_OP33_NOT_OFFSET    14
-#define    RTL8367C_OP33_NOT_MASK    0x4000
-#define    RTL8367C_ACT33_GPIO_OFFSET    13
-#define    RTL8367C_ACT33_GPIO_MASK    0x2000
-#define    RTL8367C_ACT33_FORWARD_OFFSET    12
-#define    RTL8367C_ACT33_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT33_POLICING_OFFSET    11
-#define    RTL8367C_ACT33_POLICING_MASK    0x800
-#define    RTL8367C_ACT33_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT33_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT33_SVID_OFFSET    9
-#define    RTL8367C_ACT33_SVID_MASK    0x200
-#define    RTL8367C_ACT33_CVID_OFFSET    8
-#define    RTL8367C_ACT33_CVID_MASK    0x100
-#define    RTL8367C_OP32_NOT_OFFSET    6
-#define    RTL8367C_OP32_NOT_MASK    0x40
-#define    RTL8367C_ACT32_GPIO_OFFSET    5
-#define    RTL8367C_ACT32_GPIO_MASK    0x20
-#define    RTL8367C_ACT32_FORWARD_OFFSET    4
-#define    RTL8367C_ACT32_FORWARD_MASK    0x10
-#define    RTL8367C_ACT32_POLICING_OFFSET    3
-#define    RTL8367C_ACT32_POLICING_MASK    0x8
-#define    RTL8367C_ACT32_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT32_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT32_SVID_OFFSET    1
-#define    RTL8367C_ACT32_SVID_MASK    0x2
-#define    RTL8367C_ACT32_CVID_OFFSET    0
-#define    RTL8367C_ACT32_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL17    0x0625
-#define    RTL8367C_OP35_NOT_OFFSET    14
-#define    RTL8367C_OP35_NOT_MASK    0x4000
-#define    RTL8367C_ACT35_GPIO_OFFSET    13
-#define    RTL8367C_ACT35_GPIO_MASK    0x2000
-#define    RTL8367C_ACT35_FORWARD_OFFSET    12
-#define    RTL8367C_ACT35_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT35_POLICING_OFFSET    11
-#define    RTL8367C_ACT35_POLICING_MASK    0x800
-#define    RTL8367C_ACT35_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT35_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT35_SVID_OFFSET    9
-#define    RTL8367C_ACT35_SVID_MASK    0x200
-#define    RTL8367C_ACT35_CVID_OFFSET    8
-#define    RTL8367C_ACT35_CVID_MASK    0x100
-#define    RTL8367C_OP34_NOT_OFFSET    6
-#define    RTL8367C_OP34_NOT_MASK    0x40
-#define    RTL8367C_ACT34_GPIO_OFFSET    5
-#define    RTL8367C_ACT34_GPIO_MASK    0x20
-#define    RTL8367C_ACT34_FORWARD_OFFSET    4
-#define    RTL8367C_ACT34_FORWARD_MASK    0x10
-#define    RTL8367C_ACT34_POLICING_OFFSET    3
-#define    RTL8367C_ACT34_POLICING_MASK    0x8
-#define    RTL8367C_ACT34_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT34_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT34_SVID_OFFSET    1
-#define    RTL8367C_ACT34_SVID_MASK    0x2
-#define    RTL8367C_ACT34_CVID_OFFSET    0
-#define    RTL8367C_ACT34_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL18    0x0626
-#define    RTL8367C_OP37_NOT_OFFSET    14
-#define    RTL8367C_OP37_NOT_MASK    0x4000
-#define    RTL8367C_ACT37_GPIO_OFFSET    13
-#define    RTL8367C_ACT37_GPIO_MASK    0x2000
-#define    RTL8367C_ACT37_FORWARD_OFFSET    12
-#define    RTL8367C_ACT37_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT37_POLICING_OFFSET    11
-#define    RTL8367C_ACT37_POLICING_MASK    0x800
-#define    RTL8367C_ACT37_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT37_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT37_SVID_OFFSET    9
-#define    RTL8367C_ACT37_SVID_MASK    0x200
-#define    RTL8367C_ACT37_CVID_OFFSET    8
-#define    RTL8367C_ACT37_CVID_MASK    0x100
-#define    RTL8367C_OP36_NOT_OFFSET    6
-#define    RTL8367C_OP36_NOT_MASK    0x40
-#define    RTL8367C_ACT36_GPIO_OFFSET    5
-#define    RTL8367C_ACT36_GPIO_MASK    0x20
-#define    RTL8367C_ACT36_FORWARD_OFFSET    4
-#define    RTL8367C_ACT36_FORWARD_MASK    0x10
-#define    RTL8367C_ACT36_POLICING_OFFSET    3
-#define    RTL8367C_ACT36_POLICING_MASK    0x8
-#define    RTL8367C_ACT36_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT36_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT36_SVID_OFFSET    1
-#define    RTL8367C_ACT36_SVID_MASK    0x2
-#define    RTL8367C_ACT36_CVID_OFFSET    0
-#define    RTL8367C_ACT36_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL19    0x0627
-#define    RTL8367C_OP39_NOT_OFFSET    14
-#define    RTL8367C_OP39_NOT_MASK    0x4000
-#define    RTL8367C_ACT39_GPIO_OFFSET    13
-#define    RTL8367C_ACT39_GPIO_MASK    0x2000
-#define    RTL8367C_ACT39_FORWARD_OFFSET    12
-#define    RTL8367C_ACT39_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT39_POLICING_OFFSET    11
-#define    RTL8367C_ACT39_POLICING_MASK    0x800
-#define    RTL8367C_ACT39_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT39_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT39_SVID_OFFSET    9
-#define    RTL8367C_ACT39_SVID_MASK    0x200
-#define    RTL8367C_ACT39_CVID_OFFSET    8
-#define    RTL8367C_ACT39_CVID_MASK    0x100
-#define    RTL8367C_OP38_NOT_OFFSET    6
-#define    RTL8367C_OP38_NOT_MASK    0x40
-#define    RTL8367C_ACT38_GPIO_OFFSET    5
-#define    RTL8367C_ACT38_GPIO_MASK    0x20
-#define    RTL8367C_ACT38_FORWARD_OFFSET    4
-#define    RTL8367C_ACT38_FORWARD_MASK    0x10
-#define    RTL8367C_ACT38_POLICING_OFFSET    3
-#define    RTL8367C_ACT38_POLICING_MASK    0x8
-#define    RTL8367C_ACT38_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT38_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT38_SVID_OFFSET    1
-#define    RTL8367C_ACT38_SVID_MASK    0x2
-#define    RTL8367C_ACT38_CVID_OFFSET    0
-#define    RTL8367C_ACT38_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL20    0x0628
-#define    RTL8367C_OP41_NOT_OFFSET    14
-#define    RTL8367C_OP41_NOT_MASK    0x4000
-#define    RTL8367C_ACT41_GPIO_OFFSET    13
-#define    RTL8367C_ACT41_GPIO_MASK    0x2000
-#define    RTL8367C_ACT41_FORWARD_OFFSET    12
-#define    RTL8367C_ACT41_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT41_POLICING_OFFSET    11
-#define    RTL8367C_ACT41_POLICING_MASK    0x800
-#define    RTL8367C_ACT41_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT41_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT41_SVID_OFFSET    9
-#define    RTL8367C_ACT41_SVID_MASK    0x200
-#define    RTL8367C_ACT41_CVID_OFFSET    8
-#define    RTL8367C_ACT41_CVID_MASK    0x100
-#define    RTL8367C_OP40_NOT_OFFSET    6
-#define    RTL8367C_OP40_NOT_MASK    0x40
-#define    RTL8367C_ACT40_GPIO_OFFSET    5
-#define    RTL8367C_ACT40_GPIO_MASK    0x20
-#define    RTL8367C_ACT40_FORWARD_OFFSET    4
-#define    RTL8367C_ACT40_FORWARD_MASK    0x10
-#define    RTL8367C_ACT40_POLICING_OFFSET    3
-#define    RTL8367C_ACT40_POLICING_MASK    0x8
-#define    RTL8367C_ACT40_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT40_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT40_SVID_OFFSET    1
-#define    RTL8367C_ACT40_SVID_MASK    0x2
-#define    RTL8367C_ACT40_CVID_OFFSET    0
-#define    RTL8367C_ACT40_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL21    0x0629
-#define    RTL8367C_OP43_NOT_OFFSET    14
-#define    RTL8367C_OP43_NOT_MASK    0x4000
-#define    RTL8367C_ACT43_GPIO_OFFSET    13
-#define    RTL8367C_ACT43_GPIO_MASK    0x2000
-#define    RTL8367C_ACT43_FORWARD_OFFSET    12
-#define    RTL8367C_ACT43_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT43_POLICING_OFFSET    11
-#define    RTL8367C_ACT43_POLICING_MASK    0x800
-#define    RTL8367C_ACT43_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT43_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT43_SVID_OFFSET    9
-#define    RTL8367C_ACT43_SVID_MASK    0x200
-#define    RTL8367C_ACT43_CVID_OFFSET    8
-#define    RTL8367C_ACT43_CVID_MASK    0x100
-#define    RTL8367C_OP42_NOT_OFFSET    6
-#define    RTL8367C_OP42_NOT_MASK    0x40
-#define    RTL8367C_ACT42_GPIO_OFFSET    5
-#define    RTL8367C_ACT42_GPIO_MASK    0x20
-#define    RTL8367C_ACT42_FORWARD_OFFSET    4
-#define    RTL8367C_ACT42_FORWARD_MASK    0x10
-#define    RTL8367C_ACT42_POLICING_OFFSET    3
-#define    RTL8367C_ACT42_POLICING_MASK    0x8
-#define    RTL8367C_ACT42_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT42_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT42_SVID_OFFSET    1
-#define    RTL8367C_ACT42_SVID_MASK    0x2
-#define    RTL8367C_ACT42_CVID_OFFSET    0
-#define    RTL8367C_ACT42_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL22    0x062a
-#define    RTL8367C_OP45_NOT_OFFSET    14
-#define    RTL8367C_OP45_NOT_MASK    0x4000
-#define    RTL8367C_ACT45_GPIO_OFFSET    13
-#define    RTL8367C_ACT45_GPIO_MASK    0x2000
-#define    RTL8367C_ACT45_FORWARD_OFFSET    12
-#define    RTL8367C_ACT45_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT45_POLICING_OFFSET    11
-#define    RTL8367C_ACT45_POLICING_MASK    0x800
-#define    RTL8367C_ACT45_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT45_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT45_SVID_OFFSET    9
-#define    RTL8367C_ACT45_SVID_MASK    0x200
-#define    RTL8367C_ACT45_CVID_OFFSET    8
-#define    RTL8367C_ACT45_CVID_MASK    0x100
-#define    RTL8367C_OP44_NOT_OFFSET    6
-#define    RTL8367C_OP44_NOT_MASK    0x40
-#define    RTL8367C_ACT44_GPIO_OFFSET    5
-#define    RTL8367C_ACT44_GPIO_MASK    0x20
-#define    RTL8367C_ACT44_FORWARD_OFFSET    4
-#define    RTL8367C_ACT44_FORWARD_MASK    0x10
-#define    RTL8367C_ACT44_POLICING_OFFSET    3
-#define    RTL8367C_ACT44_POLICING_MASK    0x8
-#define    RTL8367C_ACT44_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT44_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT44_SVID_OFFSET    1
-#define    RTL8367C_ACT44_SVID_MASK    0x2
-#define    RTL8367C_ACT44_CVID_OFFSET    0
-#define    RTL8367C_ACT44_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL23    0x062b
-#define    RTL8367C_OP47_NOT_OFFSET    14
-#define    RTL8367C_OP47_NOT_MASK    0x4000
-#define    RTL8367C_ACT47_GPIO_OFFSET    13
-#define    RTL8367C_ACT47_GPIO_MASK    0x2000
-#define    RTL8367C_ACT47_FORWARD_OFFSET    12
-#define    RTL8367C_ACT47_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT47_POLICING_OFFSET    11
-#define    RTL8367C_ACT47_POLICING_MASK    0x800
-#define    RTL8367C_ACT47_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT47_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT47_SVID_OFFSET    9
-#define    RTL8367C_ACT47_SVID_MASK    0x200
-#define    RTL8367C_ACT47_CVID_OFFSET    8
-#define    RTL8367C_ACT47_CVID_MASK    0x100
-#define    RTL8367C_OP46_NOT_OFFSET    6
-#define    RTL8367C_OP46_NOT_MASK    0x40
-#define    RTL8367C_ACT46_GPIO_OFFSET    5
-#define    RTL8367C_ACT46_GPIO_MASK    0x20
-#define    RTL8367C_ACT46_FORWARD_OFFSET    4
-#define    RTL8367C_ACT46_FORWARD_MASK    0x10
-#define    RTL8367C_ACT46_POLICING_OFFSET    3
-#define    RTL8367C_ACT46_POLICING_MASK    0x8
-#define    RTL8367C_ACT46_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT46_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT46_SVID_OFFSET    1
-#define    RTL8367C_ACT46_SVID_MASK    0x2
-#define    RTL8367C_ACT46_CVID_OFFSET    0
-#define    RTL8367C_ACT46_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL24    0x062c
-#define    RTL8367C_OP49_NOT_OFFSET    14
-#define    RTL8367C_OP49_NOT_MASK    0x4000
-#define    RTL8367C_ACT49_GPIO_OFFSET    13
-#define    RTL8367C_ACT49_GPIO_MASK    0x2000
-#define    RTL8367C_ACT49_FORWARD_OFFSET    12
-#define    RTL8367C_ACT49_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT49_POLICING_OFFSET    11
-#define    RTL8367C_ACT49_POLICING_MASK    0x800
-#define    RTL8367C_ACT49_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT49_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT49_SVID_OFFSET    9
-#define    RTL8367C_ACT49_SVID_MASK    0x200
-#define    RTL8367C_ACT49_CVID_OFFSET    8
-#define    RTL8367C_ACT49_CVID_MASK    0x100
-#define    RTL8367C_OP48_NOT_OFFSET    6
-#define    RTL8367C_OP48_NOT_MASK    0x40
-#define    RTL8367C_ACT48_GPIO_OFFSET    5
-#define    RTL8367C_ACT48_GPIO_MASK    0x20
-#define    RTL8367C_ACT48_FORWARD_OFFSET    4
-#define    RTL8367C_ACT48_FORWARD_MASK    0x10
-#define    RTL8367C_ACT48_POLICING_OFFSET    3
-#define    RTL8367C_ACT48_POLICING_MASK    0x8
-#define    RTL8367C_ACT48_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT48_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT48_SVID_OFFSET    1
-#define    RTL8367C_ACT48_SVID_MASK    0x2
-#define    RTL8367C_ACT48_CVID_OFFSET    0
-#define    RTL8367C_ACT48_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL25    0x062d
-#define    RTL8367C_OP51_NOT_OFFSET    14
-#define    RTL8367C_OP51_NOT_MASK    0x4000
-#define    RTL8367C_ACT51_GPIO_OFFSET    13
-#define    RTL8367C_ACT51_GPIO_MASK    0x2000
-#define    RTL8367C_ACT51_FORWARD_OFFSET    12
-#define    RTL8367C_ACT51_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT51_POLICING_OFFSET    11
-#define    RTL8367C_ACT51_POLICING_MASK    0x800
-#define    RTL8367C_ACT51_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT51_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT51_SVID_OFFSET    9
-#define    RTL8367C_ACT51_SVID_MASK    0x200
-#define    RTL8367C_ACT51_CVID_OFFSET    8
-#define    RTL8367C_ACT51_CVID_MASK    0x100
-#define    RTL8367C_OP50_NOT_OFFSET    6
-#define    RTL8367C_OP50_NOT_MASK    0x40
-#define    RTL8367C_ACT50_GPIO_OFFSET    5
-#define    RTL8367C_ACT50_GPIO_MASK    0x20
-#define    RTL8367C_ACT50_FORWARD_OFFSET    4
-#define    RTL8367C_ACT50_FORWARD_MASK    0x10
-#define    RTL8367C_ACT50_POLICING_OFFSET    3
-#define    RTL8367C_ACT50_POLICING_MASK    0x8
-#define    RTL8367C_ACT50_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT50_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT50_SVID_OFFSET    1
-#define    RTL8367C_ACT50_SVID_MASK    0x2
-#define    RTL8367C_ACT50_CVID_OFFSET    0
-#define    RTL8367C_ACT50_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL26    0x062e
-#define    RTL8367C_OP53_NOT_OFFSET    14
-#define    RTL8367C_OP53_NOT_MASK    0x4000
-#define    RTL8367C_ACT53_GPIO_OFFSET    13
-#define    RTL8367C_ACT53_GPIO_MASK    0x2000
-#define    RTL8367C_ACT53_FORWARD_OFFSET    12
-#define    RTL8367C_ACT53_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT53_POLICING_OFFSET    11
-#define    RTL8367C_ACT53_POLICING_MASK    0x800
-#define    RTL8367C_ACT53_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT53_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT53_SVID_OFFSET    9
-#define    RTL8367C_ACT53_SVID_MASK    0x200
-#define    RTL8367C_ACT53_CVID_OFFSET    8
-#define    RTL8367C_ACT53_CVID_MASK    0x100
-#define    RTL8367C_OP52_NOT_OFFSET    6
-#define    RTL8367C_OP52_NOT_MASK    0x40
-#define    RTL8367C_ACT52_GPIO_OFFSET    5
-#define    RTL8367C_ACT52_GPIO_MASK    0x20
-#define    RTL8367C_ACT52_FORWARD_OFFSET    4
-#define    RTL8367C_ACT52_FORWARD_MASK    0x10
-#define    RTL8367C_ACT52_POLICING_OFFSET    3
-#define    RTL8367C_ACT52_POLICING_MASK    0x8
-#define    RTL8367C_ACT52_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT52_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT52_SVID_OFFSET    1
-#define    RTL8367C_ACT52_SVID_MASK    0x2
-#define    RTL8367C_ACT52_CVID_OFFSET    0
-#define    RTL8367C_ACT52_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL27    0x062f
-#define    RTL8367C_OP55_NOT_OFFSET    14
-#define    RTL8367C_OP55_NOT_MASK    0x4000
-#define    RTL8367C_ACT55_GPIO_OFFSET    13
-#define    RTL8367C_ACT55_GPIO_MASK    0x2000
-#define    RTL8367C_ACT55_FORWARD_OFFSET    12
-#define    RTL8367C_ACT55_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT55_POLICING_OFFSET    11
-#define    RTL8367C_ACT55_POLICING_MASK    0x800
-#define    RTL8367C_ACT55_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT55_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT55_SVID_OFFSET    9
-#define    RTL8367C_ACT55_SVID_MASK    0x200
-#define    RTL8367C_ACT55_CVID_OFFSET    8
-#define    RTL8367C_ACT55_CVID_MASK    0x100
-#define    RTL8367C_OP54_NOT_OFFSET    6
-#define    RTL8367C_OP54_NOT_MASK    0x40
-#define    RTL8367C_ACT54_GPIO_OFFSET    5
-#define    RTL8367C_ACT54_GPIO_MASK    0x20
-#define    RTL8367C_ACT54_FORWARD_OFFSET    4
-#define    RTL8367C_ACT54_FORWARD_MASK    0x10
-#define    RTL8367C_ACT54_POLICING_OFFSET    3
-#define    RTL8367C_ACT54_POLICING_MASK    0x8
-#define    RTL8367C_ACT54_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT54_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT54_SVID_OFFSET    1
-#define    RTL8367C_ACT54_SVID_MASK    0x2
-#define    RTL8367C_ACT54_CVID_OFFSET    0
-#define    RTL8367C_ACT54_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL28    0x0630
-#define    RTL8367C_OP57_NOT_OFFSET    14
-#define    RTL8367C_OP57_NOT_MASK    0x4000
-#define    RTL8367C_ACT57_GPIO_OFFSET    13
-#define    RTL8367C_ACT57_GPIO_MASK    0x2000
-#define    RTL8367C_ACT57_FORWARD_OFFSET    12
-#define    RTL8367C_ACT57_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT57_POLICING_OFFSET    11
-#define    RTL8367C_ACT57_POLICING_MASK    0x800
-#define    RTL8367C_ACT57_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT57_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT57_SVID_OFFSET    9
-#define    RTL8367C_ACT57_SVID_MASK    0x200
-#define    RTL8367C_ACT57_CVID_OFFSET    8
-#define    RTL8367C_ACT57_CVID_MASK    0x100
-#define    RTL8367C_OP56_NOT_OFFSET    6
-#define    RTL8367C_OP56_NOT_MASK    0x40
-#define    RTL8367C_ACT56_GPIO_OFFSET    5
-#define    RTL8367C_ACT56_GPIO_MASK    0x20
-#define    RTL8367C_ACT56_FORWARD_OFFSET    4
-#define    RTL8367C_ACT56_FORWARD_MASK    0x10
-#define    RTL8367C_ACT56_POLICING_OFFSET    3
-#define    RTL8367C_ACT56_POLICING_MASK    0x8
-#define    RTL8367C_ACT56_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT56_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT56_SVID_OFFSET    1
-#define    RTL8367C_ACT56_SVID_MASK    0x2
-#define    RTL8367C_ACT56_CVID_OFFSET    0
-#define    RTL8367C_ACT56_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL29    0x0631
-#define    RTL8367C_OP59_NOT_OFFSET    14
-#define    RTL8367C_OP59_NOT_MASK    0x4000
-#define    RTL8367C_ACT59_GPIO_OFFSET    13
-#define    RTL8367C_ACT59_GPIO_MASK    0x2000
-#define    RTL8367C_ACT59_FORWARD_OFFSET    12
-#define    RTL8367C_ACT59_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT59_POLICING_OFFSET    11
-#define    RTL8367C_ACT59_POLICING_MASK    0x800
-#define    RTL8367C_ACT59_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT59_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT59_SVID_OFFSET    9
-#define    RTL8367C_ACT59_SVID_MASK    0x200
-#define    RTL8367C_ACT59_CVID_OFFSET    8
-#define    RTL8367C_ACT59_CVID_MASK    0x100
-#define    RTL8367C_OP58_NOT_OFFSET    6
-#define    RTL8367C_OP58_NOT_MASK    0x40
-#define    RTL8367C_ACT58_GPIO_OFFSET    5
-#define    RTL8367C_ACT58_GPIO_MASK    0x20
-#define    RTL8367C_ACT58_FORWARD_OFFSET    4
-#define    RTL8367C_ACT58_FORWARD_MASK    0x10
-#define    RTL8367C_ACT58_POLICING_OFFSET    3
-#define    RTL8367C_ACT58_POLICING_MASK    0x8
-#define    RTL8367C_ACT58_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT58_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT58_SVID_OFFSET    1
-#define    RTL8367C_ACT58_SVID_MASK    0x2
-#define    RTL8367C_ACT58_CVID_OFFSET    0
-#define    RTL8367C_ACT58_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL30    0x0632
-#define    RTL8367C_OP61_NOT_OFFSET    14
-#define    RTL8367C_OP61_NOT_MASK    0x4000
-#define    RTL8367C_ACT61_GPIO_OFFSET    13
-#define    RTL8367C_ACT61_GPIO_MASK    0x2000
-#define    RTL8367C_ACT61_FORWARD_OFFSET    12
-#define    RTL8367C_ACT61_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT61_POLICING_OFFSET    11
-#define    RTL8367C_ACT61_POLICING_MASK    0x800
-#define    RTL8367C_ACT61_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT61_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT61_SVID_OFFSET    9
-#define    RTL8367C_ACT61_SVID_MASK    0x200
-#define    RTL8367C_ACT61_CVID_OFFSET    8
-#define    RTL8367C_ACT61_CVID_MASK    0x100
-#define    RTL8367C_OP60_NOT_OFFSET    6
-#define    RTL8367C_OP60_NOT_MASK    0x40
-#define    RTL8367C_ACT60_GPIO_OFFSET    5
-#define    RTL8367C_ACT60_GPIO_MASK    0x20
-#define    RTL8367C_ACT60_FORWARD_OFFSET    4
-#define    RTL8367C_ACT60_FORWARD_MASK    0x10
-#define    RTL8367C_ACT60_POLICING_OFFSET    3
-#define    RTL8367C_ACT60_POLICING_MASK    0x8
-#define    RTL8367C_ACT60_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT60_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT60_SVID_OFFSET    1
-#define    RTL8367C_ACT60_SVID_MASK    0x2
-#define    RTL8367C_ACT60_CVID_OFFSET    0
-#define    RTL8367C_ACT60_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL31    0x0633
-#define    RTL8367C_OP63_NOT_OFFSET    14
-#define    RTL8367C_OP63_NOT_MASK    0x4000
-#define    RTL8367C_ACT63_GPIO_OFFSET    13
-#define    RTL8367C_ACT63_GPIO_MASK    0x2000
-#define    RTL8367C_ACT63_FORWARD_OFFSET    12
-#define    RTL8367C_ACT63_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT63_POLICING_OFFSET    11
-#define    RTL8367C_ACT63_POLICING_MASK    0x800
-#define    RTL8367C_ACT63_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT63_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT63_SVID_OFFSET    9
-#define    RTL8367C_ACT63_SVID_MASK    0x200
-#define    RTL8367C_ACT63_CVID_OFFSET    8
-#define    RTL8367C_ACT63_CVID_MASK    0x100
-#define    RTL8367C_OP62_NOT_OFFSET    6
-#define    RTL8367C_OP62_NOT_MASK    0x40
-#define    RTL8367C_ACT62_GPIO_OFFSET    5
-#define    RTL8367C_ACT62_GPIO_MASK    0x20
-#define    RTL8367C_ACT62_FORWARD_OFFSET    4
-#define    RTL8367C_ACT62_FORWARD_MASK    0x10
-#define    RTL8367C_ACT62_POLICING_OFFSET    3
-#define    RTL8367C_ACT62_POLICING_MASK    0x8
-#define    RTL8367C_ACT62_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT62_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT62_SVID_OFFSET    1
-#define    RTL8367C_ACT62_SVID_MASK    0x2
-#define    RTL8367C_ACT62_CVID_OFFSET    0
-#define    RTL8367C_ACT62_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL0    0x0635
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL1    0x0636
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL2    0x0637
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY0_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY0_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY1_CTRL0    0x0638
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY1_CTRL1    0x0639
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY1_CTRL2    0x063a
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY1_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY1_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY2_CTRL0    0x063b
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY2_CTRL1    0x063c
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY2_CTRL2    0x063d
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY2_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY2_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY3_CTRL0    0x063e
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY3_CTRL1    0x063f
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY3_CTRL2    0x0640
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY3_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY3_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY4_CTRL0    0x0641
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY4_CTRL1    0x0642
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY4_CTRL2    0x0643
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY4_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY4_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY5_CTRL0    0x0644
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY5_CTRL1    0x0645
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY5_CTRL2    0x0646
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY5_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY5_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY6_CTRL0    0x0647
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY6_CTRL1    0x0648
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY6_CTRL2    0x0649
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY6_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY6_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY7_CTRL0    0x064a
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY7_CTRL1    0x064b
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY7_CTRL2    0x064c
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY7_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY7_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY8_CTRL0    0x064d
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY8_CTRL1    0x064e
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY8_CTRL2    0x064f
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY8_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY8_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY9_CTRL0    0x0650
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY9_CTRL1    0x0651
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY9_CTRL2    0x0652
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY9_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY9_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY10_CTRL0    0x0653
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY10_CTRL1    0x0654
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY10_CTRL2    0x0655
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY10_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY10_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY11_CTRL0    0x0656
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY11_CTRL1    0x0657
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY11_CTRL2    0x0658
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY11_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY11_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY12_CTRL0    0x0659
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY12_CTRL1    0x065a
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY12_CTRL2    0x065b
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY12_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY12_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY13_CTRL0    0x065c
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY13_CTRL1    0x065d
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY13_CTRL2    0x065e
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY13_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY13_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY14_CTRL0    0x065f
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY14_CTRL1    0x0660
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY14_CTRL2    0x0661
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY14_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY14_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY15_CTRL0    0x0662
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY15_CTRL1    0x0663
-
-#define    RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY15_CTRL2    0x0664
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY15_CTRL2_OFFSET    0
-#define    RTL8367C_ACL_SDPORT_RANGE_ENTRY15_CTRL2_MASK    0x3
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY0_CTRL0    0x0665
-#define    RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY0_CTRL1    0x0666
-#define    RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY1_CTRL0    0x0667
-#define    RTL8367C_ACL_VID_RANGE_ENTRY1_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY1_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY1_CTRL1    0x0668
-#define    RTL8367C_ACL_VID_RANGE_ENTRY1_CTRL1_CHECK1_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY1_CTRL1_CHECK1_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY1_CTRL1_CHECK1_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY1_CTRL1_CHECK1_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY2_CTRL0    0x0669
-#define    RTL8367C_ACL_VID_RANGE_ENTRY2_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY2_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY2_CTRL1    0x066a
-#define    RTL8367C_ACL_VID_RANGE_ENTRY2_CTRL1_CHECK2_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY2_CTRL1_CHECK2_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY2_CTRL1_CHECK2_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY2_CTRL1_CHECK2_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY3_CTRL0    0x066b
-#define    RTL8367C_ACL_VID_RANGE_ENTRY3_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY3_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY3_CTRL1    0x066c
-#define    RTL8367C_ACL_VID_RANGE_ENTRY3_CTRL1_CHECK3_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY3_CTRL1_CHECK3_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY3_CTRL1_CHECK3_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY3_CTRL1_CHECK3_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY4_CTRL0    0x066d
-#define    RTL8367C_ACL_VID_RANGE_ENTRY4_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY4_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY4_CTRL1    0x066e
-#define    RTL8367C_ACL_VID_RANGE_ENTRY4_CTRL1_CHECK4_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY4_CTRL1_CHECK4_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY4_CTRL1_CHECK4_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY4_CTRL1_CHECK4_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY5_CTRL0    0x066f
-#define    RTL8367C_ACL_VID_RANGE_ENTRY5_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY5_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY5_CTRL1    0x0670
-#define    RTL8367C_ACL_VID_RANGE_ENTRY5_CTRL1_CHECK5_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY5_CTRL1_CHECK5_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY5_CTRL1_CHECK5_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY5_CTRL1_CHECK5_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY6_CTRL0    0x0671
-#define    RTL8367C_ACL_VID_RANGE_ENTRY6_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY6_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY6_CTRL1    0x0672
-#define    RTL8367C_ACL_VID_RANGE_ENTRY6_CTRL1_CHECK6_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY6_CTRL1_CHECK6_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY6_CTRL1_CHECK6_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY6_CTRL1_CHECK6_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY7_CTRL0    0x0673
-#define    RTL8367C_ACL_VID_RANGE_ENTRY7_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY7_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY7_CTRL1    0x0674
-#define    RTL8367C_ACL_VID_RANGE_ENTRY7_CTRL1_CHECK7_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY7_CTRL1_CHECK7_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY7_CTRL1_CHECK7_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY7_CTRL1_CHECK7_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY8_CTRL0    0x0675
-#define    RTL8367C_ACL_VID_RANGE_ENTRY8_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY8_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY8_CTRL1    0x0676
-#define    RTL8367C_ACL_VID_RANGE_ENTRY8_CTRL1_CHECK8_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY8_CTRL1_CHECK8_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY8_CTRL1_CHECK8_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY8_CTRL1_CHECK8_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY9_CTRL0    0x0677
-#define    RTL8367C_ACL_VID_RANGE_ENTRY9_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY9_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY9_CTRL1    0x0678
-#define    RTL8367C_ACL_VID_RANGE_ENTRY9_CTRL1_CHECK9_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY9_CTRL1_CHECK9_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY9_CTRL1_CHECK9_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY9_CTRL1_CHECK9_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY10_CTRL0    0x0679
-#define    RTL8367C_ACL_VID_RANGE_ENTRY10_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY10_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY10_CTRL1    0x067a
-#define    RTL8367C_ACL_VID_RANGE_ENTRY10_CTRL1_CHECK10_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY10_CTRL1_CHECK10_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY10_CTRL1_CHECK10_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY10_CTRL1_CHECK10_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY11_CTRL0    0x067b
-#define    RTL8367C_ACL_VID_RANGE_ENTRY11_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY11_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY11_CTRL1    0x067c
-#define    RTL8367C_ACL_VID_RANGE_ENTRY11_CTRL1_CHECK11_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY11_CTRL1_CHECK11_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY11_CTRL1_CHECK11_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY11_CTRL1_CHECK11_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY12_CTRL0    0x067d
-#define    RTL8367C_ACL_VID_RANGE_ENTRY12_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY12_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY12_CTRL1    0x067e
-#define    RTL8367C_ACL_VID_RANGE_ENTRY12_CTRL1_CHECK12_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY12_CTRL1_CHECK12_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY12_CTRL1_CHECK12_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY12_CTRL1_CHECK12_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY13_CTRL0    0x067f
-#define    RTL8367C_ACL_VID_RANGE_ENTRY13_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY13_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY13_CTRL1    0x0680
-#define    RTL8367C_ACL_VID_RANGE_ENTRY13_CTRL1_CHECK13_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY13_CTRL1_CHECK13_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY13_CTRL1_CHECK13_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY13_CTRL1_CHECK13_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY14_CTRL0    0x0681
-#define    RTL8367C_ACL_VID_RANGE_ENTRY14_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY14_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY14_CTRL1    0x0682
-#define    RTL8367C_ACL_VID_RANGE_ENTRY14_CTRL1_CHECK14_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY14_CTRL1_CHECK14_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY14_CTRL1_CHECK14_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY14_CTRL1_CHECK14_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY15_CTRL0    0x0683
-#define    RTL8367C_ACL_VID_RANGE_ENTRY15_CTRL0_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY15_CTRL0_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_VID_RANGE_ENTRY15_CTRL1    0x0684
-#define    RTL8367C_ACL_VID_RANGE_ENTRY15_CTRL1_CHECK15_TYPE_OFFSET    12
-#define    RTL8367C_ACL_VID_RANGE_ENTRY15_CTRL1_CHECK15_TYPE_MASK    0x3000
-#define    RTL8367C_ACL_VID_RANGE_ENTRY15_CTRL1_CHECK15_HIGH_OFFSET    0
-#define    RTL8367C_ACL_VID_RANGE_ENTRY15_CTRL1_CHECK15_HIGH_MASK    0xFFF
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL0    0x0685
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL1    0x0686
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL2    0x0687
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL3    0x0688
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL4    0x0689
-#define    RTL8367C_ACL_IP_RANGE_ENTRY0_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY0_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY1_CTRL0    0x068a
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY1_CTRL1    0x068b
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY1_CTRL2    0x068c
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY1_CTRL3    0x068d
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY1_CTRL4    0x068e
-#define    RTL8367C_ACL_IP_RANGE_ENTRY1_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY1_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY2_CTRL0    0x068f
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY2_CTRL1    0x0690
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY2_CTRL2    0x0691
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY2_CTRL3    0x0692
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY2_CTRL4    0x0693
-#define    RTL8367C_ACL_IP_RANGE_ENTRY2_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY2_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY3_CTRL0    0x0694
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY3_CTRL1    0x0695
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY3_CTRL2    0x0696
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY3_CTRL3    0x0697
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY3_CTRL4    0x0698
-#define    RTL8367C_ACL_IP_RANGE_ENTRY3_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY3_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY4_CTRL0    0x0699
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY4_CTRL1    0x069a
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY4_CTRL2    0x069b
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY4_CTRL3    0x069c
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY4_CTRL4    0x069d
-#define    RTL8367C_ACL_IP_RANGE_ENTRY4_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY4_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY5_CTRL0    0x069e
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY5_CTRL1    0x069f
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY5_CTRL2    0x06a0
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY5_CTRL3    0x06a1
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY5_CTRL4    0x06a2
-#define    RTL8367C_ACL_IP_RANGE_ENTRY5_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY5_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY6_CTRL0    0x06a3
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY6_CTRL1    0x06a4
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY6_CTRL2    0x06a5
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY6_CTRL3    0x06a6
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY6_CTRL4    0x06a7
-#define    RTL8367C_ACL_IP_RANGE_ENTRY6_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY6_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY7_CTRL0    0x06a8
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY7_CTRL1    0x06a9
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY7_CTRL2    0x06aa
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY7_CTRL3    0x06ab
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY7_CTRL4    0x06ac
-#define    RTL8367C_ACL_IP_RANGE_ENTRY7_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY7_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY8_CTRL0    0x06ad
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY8_CTRL1    0x06ae
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY8_CTRL2    0x06af
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY8_CTRL3    0x06b0
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY8_CTRL4    0x06b1
-#define    RTL8367C_ACL_IP_RANGE_ENTRY8_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY8_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY9_CTRL0    0x06b2
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY9_CTRL1    0x06b3
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY9_CTRL2    0x06b4
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY9_CTRL3    0x06b5
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY9_CTRL4    0x06b6
-#define    RTL8367C_ACL_IP_RANGE_ENTRY9_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY9_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY10_CTRL0    0x06b7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY10_CTRL1    0x06b8
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY10_CTRL2    0x06b9
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY10_CTRL3    0x06ba
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY10_CTRL4    0x06bb
-#define    RTL8367C_ACL_IP_RANGE_ENTRY10_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY10_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY11_CTRL0    0x06bc
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY11_CTRL1    0x06bd
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY11_CTRL2    0x06be
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY11_CTRL3    0x06bf
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY11_CTRL4    0x06c0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY11_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY11_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY12_CTRL0    0x06c1
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY12_CTRL1    0x06c2
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY12_CTRL2    0x06c3
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY12_CTRL3    0x06c4
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY12_CTRL4    0x06c5
-#define    RTL8367C_ACL_IP_RANGE_ENTRY12_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY12_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY13_CTRL0    0x06c6
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY13_CTRL1    0x06c7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY13_CTRL2    0x06c8
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY13_CTRL3    0x06c9
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY13_CTRL4    0x06ca
-#define    RTL8367C_ACL_IP_RANGE_ENTRY13_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY13_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY14_CTRL0    0x06cb
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY14_CTRL1    0x06cc
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY14_CTRL2    0x06cd
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY14_CTRL3    0x06ce
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY14_CTRL4    0x06cf
-#define    RTL8367C_ACL_IP_RANGE_ENTRY14_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY14_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY15_CTRL0    0x06d0
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY15_CTRL1    0x06d1
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY15_CTRL2    0x06d2
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY15_CTRL3    0x06d3
-
-#define    RTL8367C_REG_ACL_IP_RANGE_ENTRY15_CTRL4    0x06d4
-#define    RTL8367C_ACL_IP_RANGE_ENTRY15_CTRL4_OFFSET    0
-#define    RTL8367C_ACL_IP_RANGE_ENTRY15_CTRL4_MASK    0x7
-
-#define    RTL8367C_REG_ACL_ENABLE    0x06d5
-#define    RTL8367C_PORT10_ENABLE_OFFSET    10
-#define    RTL8367C_PORT10_ENABLE_MASK    0x400
-#define    RTL8367C_PORT9_ENABLE_OFFSET    9
-#define    RTL8367C_PORT9_ENABLE_MASK    0x200
-#define    RTL8367C_PORT8_ENABLE_OFFSET    8
-#define    RTL8367C_PORT8_ENABLE_MASK    0x100
-#define    RTL8367C_PORT7_ENABLE_OFFSET    7
-#define    RTL8367C_PORT7_ENABLE_MASK    0x80
-#define    RTL8367C_PORT6_ENABLE_OFFSET    6
-#define    RTL8367C_PORT6_ENABLE_MASK    0x40
-#define    RTL8367C_PORT5_ENABLE_OFFSET    5
-#define    RTL8367C_PORT5_ENABLE_MASK    0x20
-#define    RTL8367C_PORT4_ENABLE_OFFSET    4
-#define    RTL8367C_PORT4_ENABLE_MASK    0x10
-#define    RTL8367C_PORT3_ENABLE_OFFSET    3
-#define    RTL8367C_PORT3_ENABLE_MASK    0x8
-#define    RTL8367C_PORT2_ENABLE_OFFSET    2
-#define    RTL8367C_PORT2_ENABLE_MASK    0x4
-#define    RTL8367C_PORT1_ENABLE_OFFSET    1
-#define    RTL8367C_PORT1_ENABLE_MASK    0x2
-#define    RTL8367C_PORT0_ENABLE_OFFSET    0
-#define    RTL8367C_PORT0_ENABLE_MASK    0x1
-
-#define    RTL8367C_REG_ACL_UNMATCH_PERMIT    0x06d6
-#define    RTL8367C_PORT10_PERMIT_OFFSET    10
-#define    RTL8367C_PORT10_PERMIT_MASK    0x400
-#define    RTL8367C_PORT9_PERMIT_OFFSET    9
-#define    RTL8367C_PORT9_PERMIT_MASK    0x200
-#define    RTL8367C_PORT8_PERMIT_OFFSET    8
-#define    RTL8367C_PORT8_PERMIT_MASK    0x100
-#define    RTL8367C_PORT7_PERMIT_OFFSET    7
-#define    RTL8367C_PORT7_PERMIT_MASK    0x80
-#define    RTL8367C_PORT6_PERMIT_OFFSET    6
-#define    RTL8367C_PORT6_PERMIT_MASK    0x40
-#define    RTL8367C_PORT5_PERMIT_OFFSET    5
-#define    RTL8367C_PORT5_PERMIT_MASK    0x20
-#define    RTL8367C_PORT4_PERMIT_OFFSET    4
-#define    RTL8367C_PORT4_PERMIT_MASK    0x10
-#define    RTL8367C_PORT3_PERMIT_OFFSET    3
-#define    RTL8367C_PORT3_PERMIT_MASK    0x8
-#define    RTL8367C_PORT2_PERMIT_OFFSET    2
-#define    RTL8367C_PORT2_PERMIT_MASK    0x4
-#define    RTL8367C_PORT1_PERMIT_OFFSET    1
-#define    RTL8367C_PORT1_PERMIT_MASK    0x2
-#define    RTL8367C_PORT0_PERMIT_OFFSET    0
-#define    RTL8367C_PORT0_PERMIT_MASK    0x1
-
-#define    RTL8367C_REG_ACL_GPIO_POLARITY    0x06d7
-#define    RTL8367C_ACL_GPIO_POLARITY_OFFSET    0
-#define    RTL8367C_ACL_GPIO_POLARITY_MASK    0x1
-
-#define    RTL8367C_REG_ACL_LOG_CNT_TYPE    0x06d8
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER15_TYPE_OFFSET    15
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER15_TYPE_MASK    0x8000
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER14_TYPE_OFFSET    14
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER14_TYPE_MASK    0x4000
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER13_TYPE_OFFSET    13
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER13_TYPE_MASK    0x2000
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER12_TYPE_OFFSET    12
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER12_TYPE_MASK    0x1000
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER11_TYPE_OFFSET    11
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER11_TYPE_MASK    0x800
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER10_TYPE_OFFSET    10
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER10_TYPE_MASK    0x400
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER9_TYPE_OFFSET    9
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER9_TYPE_MASK    0x200
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER8_TYPE_OFFSET    8
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER8_TYPE_MASK    0x100
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER7_TYPE_OFFSET    7
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER7_TYPE_MASK    0x80
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER6_TYPE_OFFSET    6
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER6_TYPE_MASK    0x40
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER5_TYPE_OFFSET    5
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER5_TYPE_MASK    0x20
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER4_TYPE_OFFSET    4
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER4_TYPE_MASK    0x10
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER3_TYPE_OFFSET    3
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER3_TYPE_MASK    0x8
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER2_TYPE_OFFSET    2
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER2_TYPE_MASK    0x4
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER1_TYPE_OFFSET    1
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER1_TYPE_MASK    0x2
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER0_TYPE_OFFSET    0
-#define    RTL8367C_ACL_LOG_CNT_TYPE_COUNTER0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_ACL_RESET_CFG    0x06d9
-#define    RTL8367C_ACL_RESET_CFG_OFFSET    0
-#define    RTL8367C_ACL_RESET_CFG_MASK    0x1
-
-#define    RTL8367C_REG_ACL_DUMMY00    0x06E0
-
-#define    RTL8367C_REG_ACL_DUMMY01    0x06E1
-
-#define    RTL8367C_REG_ACL_DUMMY02    0x06E2
-
-#define    RTL8367C_REG_ACL_DUMMY03    0x06E3
-
-#define    RTL8367C_REG_ACL_DUMMY04    0x06E4
-
-#define    RTL8367C_REG_ACL_DUMMY05    0x06E5
-
-#define    RTL8367C_REG_ACL_DUMMY06    0x06E6
-
-#define    RTL8367C_REG_ACL_DUMMY07    0x06E7
-
-#define    RTL8367C_REG_ACL_REASON_01    0x06E8
-#define    RTL8367C_ACL_ACT_1_OFFSET    8
-#define    RTL8367C_ACL_ACT_1_MASK    0xFF00
-#define    RTL8367C_ACL_ACT_0_OFFSET    0
-#define    RTL8367C_ACL_ACT_0_MASK    0xFF
-
-#define    RTL8367C_REG_ACL_REASON_23    0x06E9
-#define    RTL8367C_ACL_ACT_3_OFFSET    8
-#define    RTL8367C_ACL_ACT_3_MASK    0xFF00
-#define    RTL8367C_ACL_ACT_2_OFFSET    0
-#define    RTL8367C_ACL_ACT_2_MASK    0xFF
-
-#define    RTL8367C_REG_ACL_REASON_45    0x06EA
-#define    RTL8367C_ACL_ACT_5_OFFSET    8
-#define    RTL8367C_ACL_ACT_5_MASK    0xFF00
-#define    RTL8367C_ACL_ACT_4_OFFSET    0
-#define    RTL8367C_ACL_ACT_4_MASK    0xFF
-
-#define    RTL8367C_REG_ACL_ACCESS_MODE    0x06EB
-#define    RTL8367C_ACL_ACCESS_MODE_OFFSET    0
-#define    RTL8367C_ACL_ACCESS_MODE_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL32    0x06F0
-#define    RTL8367C_OP65_NOT_OFFSET    14
-#define    RTL8367C_OP65_NOT_MASK    0x4000
-#define    RTL8367C_ACT65_GPIO_OFFSET    13
-#define    RTL8367C_ACT65_GPIO_MASK    0x2000
-#define    RTL8367C_ACT65_FORWARD_OFFSET    12
-#define    RTL8367C_ACT65_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT65_POLICING_OFFSET    11
-#define    RTL8367C_ACT65_POLICING_MASK    0x800
-#define    RTL8367C_ACT65_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT65_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT65_SVID_OFFSET    9
-#define    RTL8367C_ACT65_SVID_MASK    0x200
-#define    RTL8367C_ACT65_CVID_OFFSET    8
-#define    RTL8367C_ACT65_CVID_MASK    0x100
-#define    RTL8367C_OP64_NOT_OFFSET    6
-#define    RTL8367C_OP64_NOT_MASK    0x40
-#define    RTL8367C_ACT64_GPIO_OFFSET    5
-#define    RTL8367C_ACT64_GPIO_MASK    0x20
-#define    RTL8367C_ACT64_FORWARD_OFFSET    4
-#define    RTL8367C_ACT64_FORWARD_MASK    0x10
-#define    RTL8367C_ACT64_POLICING_OFFSET    3
-#define    RTL8367C_ACT64_POLICING_MASK    0x8
-#define    RTL8367C_ACT64_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT64_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT64_SVID_OFFSET    1
-#define    RTL8367C_ACT64_SVID_MASK    0x2
-#define    RTL8367C_ACT64_CVID_OFFSET    0
-#define    RTL8367C_ACT64_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL33    0x06F1
-#define    RTL8367C_OP67_NOT_OFFSET    14
-#define    RTL8367C_OP67_NOT_MASK    0x4000
-#define    RTL8367C_ACT67_GPIO_OFFSET    13
-#define    RTL8367C_ACT67_GPIO_MASK    0x2000
-#define    RTL8367C_ACT67_FORWARD_OFFSET    12
-#define    RTL8367C_ACT67_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT67_POLICING_OFFSET    11
-#define    RTL8367C_ACT67_POLICING_MASK    0x800
-#define    RTL8367C_ACT67_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT67_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT67_SVID_OFFSET    9
-#define    RTL8367C_ACT67_SVID_MASK    0x200
-#define    RTL8367C_ACT67_CVID_OFFSET    8
-#define    RTL8367C_ACT67_CVID_MASK    0x100
-#define    RTL8367C_OP66_NOT_OFFSET    6
-#define    RTL8367C_OP66_NOT_MASK    0x40
-#define    RTL8367C_ACT66_GPIO_OFFSET    5
-#define    RTL8367C_ACT66_GPIO_MASK    0x20
-#define    RTL8367C_ACT66_FORWARD_OFFSET    4
-#define    RTL8367C_ACT66_FORWARD_MASK    0x10
-#define    RTL8367C_ACT66_POLICING_OFFSET    3
-#define    RTL8367C_ACT66_POLICING_MASK    0x8
-#define    RTL8367C_ACT66_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT66_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT66_SVID_OFFSET    1
-#define    RTL8367C_ACT66_SVID_MASK    0x2
-#define    RTL8367C_ACT66_CVID_OFFSET    0
-#define    RTL8367C_ACT66_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL34    0x06F2
-#define    RTL8367C_OP69_NOT_OFFSET    14
-#define    RTL8367C_OP69_NOT_MASK    0x4000
-#define    RTL8367C_ACT69_GPIO_OFFSET    13
-#define    RTL8367C_ACT69_GPIO_MASK    0x2000
-#define    RTL8367C_ACT69_FORWARD_OFFSET    12
-#define    RTL8367C_ACT69_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT69_POLICING_OFFSET    11
-#define    RTL8367C_ACT69_POLICING_MASK    0x800
-#define    RTL8367C_ACT69_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT69_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT69_SVID_OFFSET    9
-#define    RTL8367C_ACT69_SVID_MASK    0x200
-#define    RTL8367C_ACT69_CVID_OFFSET    8
-#define    RTL8367C_ACT69_CVID_MASK    0x100
-#define    RTL8367C_OP68_NOT_OFFSET    6
-#define    RTL8367C_OP68_NOT_MASK    0x40
-#define    RTL8367C_ACT68_GPIO_OFFSET    5
-#define    RTL8367C_ACT68_GPIO_MASK    0x20
-#define    RTL8367C_ACT68_FORWARD_OFFSET    4
-#define    RTL8367C_ACT68_FORWARD_MASK    0x10
-#define    RTL8367C_ACT68_POLICING_OFFSET    3
-#define    RTL8367C_ACT68_POLICING_MASK    0x8
-#define    RTL8367C_ACT68_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT68_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT68_SVID_OFFSET    1
-#define    RTL8367C_ACT68_SVID_MASK    0x2
-#define    RTL8367C_ACT68_CVID_OFFSET    0
-#define    RTL8367C_ACT68_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL35    0x06F3
-#define    RTL8367C_OP71_NOT_OFFSET    14
-#define    RTL8367C_OP71_NOT_MASK    0x4000
-#define    RTL8367C_ACT71_GPIO_OFFSET    13
-#define    RTL8367C_ACT71_GPIO_MASK    0x2000
-#define    RTL8367C_ACT71_FORWARD_OFFSET    12
-#define    RTL8367C_ACT71_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT71_POLICING_OFFSET    11
-#define    RTL8367C_ACT71_POLICING_MASK    0x800
-#define    RTL8367C_ACT71_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT71_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT71_SVID_OFFSET    9
-#define    RTL8367C_ACT71_SVID_MASK    0x200
-#define    RTL8367C_ACT71_CVID_OFFSET    8
-#define    RTL8367C_ACT71_CVID_MASK    0x100
-#define    RTL8367C_OP70_NOT_OFFSET    6
-#define    RTL8367C_OP70_NOT_MASK    0x40
-#define    RTL8367C_ACT70_GPIO_OFFSET    5
-#define    RTL8367C_ACT70_GPIO_MASK    0x20
-#define    RTL8367C_ACT70_FORWARD_OFFSET    4
-#define    RTL8367C_ACT70_FORWARD_MASK    0x10
-#define    RTL8367C_ACT70_POLICING_OFFSET    3
-#define    RTL8367C_ACT70_POLICING_MASK    0x8
-#define    RTL8367C_ACT70_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT70_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT70_SVID_OFFSET    1
-#define    RTL8367C_ACT70_SVID_MASK    0x2
-#define    RTL8367C_ACT70_CVID_OFFSET    0
-#define    RTL8367C_ACT70_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL36    0x06F4
-#define    RTL8367C_OP73_NOT_OFFSET    14
-#define    RTL8367C_OP73_NOT_MASK    0x4000
-#define    RTL8367C_ACT73_GPIO_OFFSET    13
-#define    RTL8367C_ACT73_GPIO_MASK    0x2000
-#define    RTL8367C_ACT73_FORWARD_OFFSET    12
-#define    RTL8367C_ACT73_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT73_POLICING_OFFSET    11
-#define    RTL8367C_ACT73_POLICING_MASK    0x800
-#define    RTL8367C_ACT73_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT73_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT73_SVID_OFFSET    9
-#define    RTL8367C_ACT73_SVID_MASK    0x200
-#define    RTL8367C_ACT73_CVID_OFFSET    8
-#define    RTL8367C_ACT73_CVID_MASK    0x100
-#define    RTL8367C_OP72_NOT_OFFSET    6
-#define    RTL8367C_OP72_NOT_MASK    0x40
-#define    RTL8367C_ACT72_GPIO_OFFSET    5
-#define    RTL8367C_ACT72_GPIO_MASK    0x20
-#define    RTL8367C_ACT72_FORWARD_OFFSET    4
-#define    RTL8367C_ACT72_FORWARD_MASK    0x10
-#define    RTL8367C_ACT72_POLICING_OFFSET    3
-#define    RTL8367C_ACT72_POLICING_MASK    0x8
-#define    RTL8367C_ACT72_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT72_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT72_SVID_OFFSET    1
-#define    RTL8367C_ACT72_SVID_MASK    0x2
-#define    RTL8367C_ACT72_CVID_OFFSET    0
-#define    RTL8367C_ACT72_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL37    0x06F5
-#define    RTL8367C_OP75_NOT_OFFSET    14
-#define    RTL8367C_OP75_NOT_MASK    0x4000
-#define    RTL8367C_ACT75_GPIO_OFFSET    13
-#define    RTL8367C_ACT75_GPIO_MASK    0x2000
-#define    RTL8367C_ACT75_FORWARD_OFFSET    12
-#define    RTL8367C_ACT75_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT75_POLICING_OFFSET    11
-#define    RTL8367C_ACT75_POLICING_MASK    0x800
-#define    RTL8367C_ACT75_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT75_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT75_SVID_OFFSET    9
-#define    RTL8367C_ACT75_SVID_MASK    0x200
-#define    RTL8367C_ACT75_CVID_OFFSET    8
-#define    RTL8367C_ACT75_CVID_MASK    0x100
-#define    RTL8367C_OP74_NOT_OFFSET    6
-#define    RTL8367C_OP74_NOT_MASK    0x40
-#define    RTL8367C_ACT74_GPIO_OFFSET    5
-#define    RTL8367C_ACT74_GPIO_MASK    0x20
-#define    RTL8367C_ACT74_FORWARD_OFFSET    4
-#define    RTL8367C_ACT74_FORWARD_MASK    0x10
-#define    RTL8367C_ACT74_POLICING_OFFSET    3
-#define    RTL8367C_ACT74_POLICING_MASK    0x8
-#define    RTL8367C_ACT74_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT74_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT74_SVID_OFFSET    1
-#define    RTL8367C_ACT74_SVID_MASK    0x2
-#define    RTL8367C_ACT74_CVID_OFFSET    0
-#define    RTL8367C_ACT74_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL38    0x06F6
-#define    RTL8367C_OP77_NOT_OFFSET    14
-#define    RTL8367C_OP77_NOT_MASK    0x4000
-#define    RTL8367C_ACT77_GPIO_OFFSET    13
-#define    RTL8367C_ACT77_GPIO_MASK    0x2000
-#define    RTL8367C_ACT77_FORWARD_OFFSET    12
-#define    RTL8367C_ACT77_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT77_POLICING_OFFSET    11
-#define    RTL8367C_ACT77_POLICING_MASK    0x800
-#define    RTL8367C_ACT77_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT77_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT77_SVID_OFFSET    9
-#define    RTL8367C_ACT77_SVID_MASK    0x200
-#define    RTL8367C_ACT77_CVID_OFFSET    8
-#define    RTL8367C_ACT77_CVID_MASK    0x100
-#define    RTL8367C_OP76_NOT_OFFSET    6
-#define    RTL8367C_OP76_NOT_MASK    0x40
-#define    RTL8367C_ACT76_GPIO_OFFSET    5
-#define    RTL8367C_ACT76_GPIO_MASK    0x20
-#define    RTL8367C_ACT76_FORWARD_OFFSET    4
-#define    RTL8367C_ACT76_FORWARD_MASK    0x10
-#define    RTL8367C_ACT76_POLICING_OFFSET    3
-#define    RTL8367C_ACT76_POLICING_MASK    0x8
-#define    RTL8367C_ACT76_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT76_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT76_SVID_OFFSET    1
-#define    RTL8367C_ACT76_SVID_MASK    0x2
-#define    RTL8367C_ACT76_CVID_OFFSET    0
-#define    RTL8367C_ACT76_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL39    0x06F7
-#define    RTL8367C_OP79_NOT_OFFSET    14
-#define    RTL8367C_OP79_NOT_MASK    0x4000
-#define    RTL8367C_ACT79_GPIO_OFFSET    13
-#define    RTL8367C_ACT79_GPIO_MASK    0x2000
-#define    RTL8367C_ACT79_FORWARD_OFFSET    12
-#define    RTL8367C_ACT79_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT79_POLICING_OFFSET    11
-#define    RTL8367C_ACT79_POLICING_MASK    0x800
-#define    RTL8367C_ACT79_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT79_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT79_SVID_OFFSET    9
-#define    RTL8367C_ACT79_SVID_MASK    0x200
-#define    RTL8367C_ACT79_CVID_OFFSET    8
-#define    RTL8367C_ACT79_CVID_MASK    0x100
-#define    RTL8367C_OP78_NOT_OFFSET    6
-#define    RTL8367C_OP78_NOT_MASK    0x40
-#define    RTL8367C_ACT78_GPIO_OFFSET    5
-#define    RTL8367C_ACT78_GPIO_MASK    0x20
-#define    RTL8367C_ACT78_FORWARD_OFFSET    4
-#define    RTL8367C_ACT78_FORWARD_MASK    0x10
-#define    RTL8367C_ACT78_POLICING_OFFSET    3
-#define    RTL8367C_ACT78_POLICING_MASK    0x8
-#define    RTL8367C_ACT78_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT78_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT78_SVID_OFFSET    1
-#define    RTL8367C_ACT78_SVID_MASK    0x2
-#define    RTL8367C_ACT78_CVID_OFFSET    0
-#define    RTL8367C_ACT78_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL40    0x06F8
-#define    RTL8367C_OP81_NOT_OFFSET    14
-#define    RTL8367C_OP81_NOT_MASK    0x4000
-#define    RTL8367C_ACT81_GPIO_OFFSET    13
-#define    RTL8367C_ACT81_GPIO_MASK    0x2000
-#define    RTL8367C_ACT81_FORWARD_OFFSET    12
-#define    RTL8367C_ACT81_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT81_POLICING_OFFSET    11
-#define    RTL8367C_ACT81_POLICING_MASK    0x800
-#define    RTL8367C_ACT81_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT81_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT81_SVID_OFFSET    9
-#define    RTL8367C_ACT81_SVID_MASK    0x200
-#define    RTL8367C_ACT81_CVID_OFFSET    8
-#define    RTL8367C_ACT81_CVID_MASK    0x100
-#define    RTL8367C_OP80_NOT_OFFSET    6
-#define    RTL8367C_OP80_NOT_MASK    0x40
-#define    RTL8367C_ACT80_GPIO_OFFSET    5
-#define    RTL8367C_ACT80_GPIO_MASK    0x20
-#define    RTL8367C_ACT80_FORWARD_OFFSET    4
-#define    RTL8367C_ACT80_FORWARD_MASK    0x10
-#define    RTL8367C_ACT80_POLICING_OFFSET    3
-#define    RTL8367C_ACT80_POLICING_MASK    0x8
-#define    RTL8367C_ACT80_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT80_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT80_SVID_OFFSET    1
-#define    RTL8367C_ACT80_SVID_MASK    0x2
-#define    RTL8367C_ACT80_CVID_OFFSET    0
-#define    RTL8367C_ACT80_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL41    0x06F9
-#define    RTL8367C_OP83_NOT_OFFSET    14
-#define    RTL8367C_OP83_NOT_MASK    0x4000
-#define    RTL8367C_ACT83_GPIO_OFFSET    13
-#define    RTL8367C_ACT83_GPIO_MASK    0x2000
-#define    RTL8367C_ACT83_FORWARD_OFFSET    12
-#define    RTL8367C_ACT83_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT83_POLICING_OFFSET    11
-#define    RTL8367C_ACT83_POLICING_MASK    0x800
-#define    RTL8367C_ACT83_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT83_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT83_SVID_OFFSET    9
-#define    RTL8367C_ACT83_SVID_MASK    0x200
-#define    RTL8367C_ACT83_CVID_OFFSET    8
-#define    RTL8367C_ACT83_CVID_MASK    0x100
-#define    RTL8367C_OP82_NOT_OFFSET    6
-#define    RTL8367C_OP82_NOT_MASK    0x40
-#define    RTL8367C_ACT82_GPIO_OFFSET    5
-#define    RTL8367C_ACT82_GPIO_MASK    0x20
-#define    RTL8367C_ACT82_FORWARD_OFFSET    4
-#define    RTL8367C_ACT82_FORWARD_MASK    0x10
-#define    RTL8367C_ACT82_POLICING_OFFSET    3
-#define    RTL8367C_ACT82_POLICING_MASK    0x8
-#define    RTL8367C_ACT82_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT82_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT82_SVID_OFFSET    1
-#define    RTL8367C_ACT82_SVID_MASK    0x2
-#define    RTL8367C_ACT82_CVID_OFFSET    0
-#define    RTL8367C_ACT82_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL42    0x06FA
-#define    RTL8367C_OP85_NOT_OFFSET    14
-#define    RTL8367C_OP85_NOT_MASK    0x4000
-#define    RTL8367C_ACT85_GPIO_OFFSET    13
-#define    RTL8367C_ACT85_GPIO_MASK    0x2000
-#define    RTL8367C_ACT85_FORWARD_OFFSET    12
-#define    RTL8367C_ACT85_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT85_POLICING_OFFSET    11
-#define    RTL8367C_ACT85_POLICING_MASK    0x800
-#define    RTL8367C_ACT85_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT85_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT85_SVID_OFFSET    9
-#define    RTL8367C_ACT85_SVID_MASK    0x200
-#define    RTL8367C_ACT85_CVID_OFFSET    8
-#define    RTL8367C_ACT85_CVID_MASK    0x100
-#define    RTL8367C_OP84_NOT_OFFSET    6
-#define    RTL8367C_OP84_NOT_MASK    0x40
-#define    RTL8367C_ACT84_GPIO_OFFSET    5
-#define    RTL8367C_ACT84_GPIO_MASK    0x20
-#define    RTL8367C_ACT84_FORWARD_OFFSET    4
-#define    RTL8367C_ACT84_FORWARD_MASK    0x10
-#define    RTL8367C_ACT84_POLICING_OFFSET    3
-#define    RTL8367C_ACT84_POLICING_MASK    0x8
-#define    RTL8367C_ACT84_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT84_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT84_SVID_OFFSET    1
-#define    RTL8367C_ACT84_SVID_MASK    0x2
-#define    RTL8367C_ACT84_CVID_OFFSET    0
-#define    RTL8367C_ACT84_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL43    0x06FB
-#define    RTL8367C_OP87_NOT_OFFSET    14
-#define    RTL8367C_OP87_NOT_MASK    0x4000
-#define    RTL8367C_ACT87_GPIO_OFFSET    13
-#define    RTL8367C_ACT87_GPIO_MASK    0x2000
-#define    RTL8367C_ACT87_FORWARD_OFFSET    12
-#define    RTL8367C_ACT87_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT87_POLICING_OFFSET    11
-#define    RTL8367C_ACT87_POLICING_MASK    0x800
-#define    RTL8367C_ACT87_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT87_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT87_SVID_OFFSET    9
-#define    RTL8367C_ACT87_SVID_MASK    0x200
-#define    RTL8367C_ACT87_CVID_OFFSET    8
-#define    RTL8367C_ACT87_CVID_MASK    0x100
-#define    RTL8367C_OP86_NOT_OFFSET    6
-#define    RTL8367C_OP86_NOT_MASK    0x40
-#define    RTL8367C_ACT86_GPIO_OFFSET    5
-#define    RTL8367C_ACT86_GPIO_MASK    0x20
-#define    RTL8367C_ACT86_FORWARD_OFFSET    4
-#define    RTL8367C_ACT86_FORWARD_MASK    0x10
-#define    RTL8367C_ACT86_POLICING_OFFSET    3
-#define    RTL8367C_ACT86_POLICING_MASK    0x8
-#define    RTL8367C_ACT86_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT86_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT86_SVID_OFFSET    1
-#define    RTL8367C_ACT86_SVID_MASK    0x2
-#define    RTL8367C_ACT86_CVID_OFFSET    0
-#define    RTL8367C_ACT86_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL44    0x06FC
-#define    RTL8367C_OP89_NOT_OFFSET    14
-#define    RTL8367C_OP89_NOT_MASK    0x4000
-#define    RTL8367C_ACT89_GPIO_OFFSET    13
-#define    RTL8367C_ACT89_GPIO_MASK    0x2000
-#define    RTL8367C_ACT89_FORWARD_OFFSET    12
-#define    RTL8367C_ACT89_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT89_POLICING_OFFSET    11
-#define    RTL8367C_ACT89_POLICING_MASK    0x800
-#define    RTL8367C_ACT89_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT89_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT89_SVID_OFFSET    9
-#define    RTL8367C_ACT89_SVID_MASK    0x200
-#define    RTL8367C_ACT89_CVID_OFFSET    8
-#define    RTL8367C_ACT89_CVID_MASK    0x100
-#define    RTL8367C_OP88_NOT_OFFSET    6
-#define    RTL8367C_OP88_NOT_MASK    0x40
-#define    RTL8367C_ACT88_GPIO_OFFSET    5
-#define    RTL8367C_ACT88_GPIO_MASK    0x20
-#define    RTL8367C_ACT88_FORWARD_OFFSET    4
-#define    RTL8367C_ACT88_FORWARD_MASK    0x10
-#define    RTL8367C_ACT88_POLICING_OFFSET    3
-#define    RTL8367C_ACT88_POLICING_MASK    0x8
-#define    RTL8367C_ACT88_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT88_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT88_SVID_OFFSET    1
-#define    RTL8367C_ACT88_SVID_MASK    0x2
-#define    RTL8367C_ACT88_CVID_OFFSET    0
-#define    RTL8367C_ACT88_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL45    0x06FD
-#define    RTL8367C_OP91_NOT_OFFSET    14
-#define    RTL8367C_OP91_NOT_MASK    0x4000
-#define    RTL8367C_ACT91_GPIO_OFFSET    13
-#define    RTL8367C_ACT91_GPIO_MASK    0x2000
-#define    RTL8367C_ACT91_FORWARD_OFFSET    12
-#define    RTL8367C_ACT91_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT91_POLICING_OFFSET    11
-#define    RTL8367C_ACT91_POLICING_MASK    0x800
-#define    RTL8367C_ACT91_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT91_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT91_SVID_OFFSET    9
-#define    RTL8367C_ACT91_SVID_MASK    0x200
-#define    RTL8367C_ACT91_CVID_OFFSET    8
-#define    RTL8367C_ACT91_CVID_MASK    0x100
-#define    RTL8367C_OP90_NOT_OFFSET    6
-#define    RTL8367C_OP90_NOT_MASK    0x40
-#define    RTL8367C_ACT90_GPIO_OFFSET    5
-#define    RTL8367C_ACT90_GPIO_MASK    0x20
-#define    RTL8367C_ACT90_FORWARD_OFFSET    4
-#define    RTL8367C_ACT90_FORWARD_MASK    0x10
-#define    RTL8367C_ACT90_POLICING_OFFSET    3
-#define    RTL8367C_ACT90_POLICING_MASK    0x8
-#define    RTL8367C_ACT90_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT90_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT90_SVID_OFFSET    1
-#define    RTL8367C_ACT90_SVID_MASK    0x2
-#define    RTL8367C_ACT90_CVID_OFFSET    0
-#define    RTL8367C_ACT90_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL46    0x06FE
-#define    RTL8367C_OP93_NOT_OFFSET    14
-#define    RTL8367C_OP93_NOT_MASK    0x4000
-#define    RTL8367C_ACT93_GPIO_OFFSET    13
-#define    RTL8367C_ACT93_GPIO_MASK    0x2000
-#define    RTL8367C_ACT93_FORWARD_OFFSET    12
-#define    RTL8367C_ACT93_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT93_POLICING_OFFSET    11
-#define    RTL8367C_ACT93_POLICING_MASK    0x800
-#define    RTL8367C_ACT93_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT93_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT93_SVID_OFFSET    9
-#define    RTL8367C_ACT93_SVID_MASK    0x200
-#define    RTL8367C_ACT93_CVID_OFFSET    8
-#define    RTL8367C_ACT93_CVID_MASK    0x100
-#define    RTL8367C_OP92_NOT_OFFSET    6
-#define    RTL8367C_OP92_NOT_MASK    0x40
-#define    RTL8367C_ACT92_GPIO_OFFSET    5
-#define    RTL8367C_ACT92_GPIO_MASK    0x20
-#define    RTL8367C_ACT92_FORWARD_OFFSET    4
-#define    RTL8367C_ACT92_FORWARD_MASK    0x10
-#define    RTL8367C_ACT92_POLICING_OFFSET    3
-#define    RTL8367C_ACT92_POLICING_MASK    0x8
-#define    RTL8367C_ACT92_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT92_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT92_SVID_OFFSET    1
-#define    RTL8367C_ACT92_SVID_MASK    0x2
-#define    RTL8367C_ACT92_CVID_OFFSET    0
-#define    RTL8367C_ACT92_CVID_MASK    0x1
-
-#define    RTL8367C_REG_ACL_ACTION_CTRL47    0x06FF
-#define    RTL8367C_OP95_NOT_OFFSET    14
-#define    RTL8367C_OP95_NOT_MASK    0x4000
-#define    RTL8367C_ACT95_GPIO_OFFSET    13
-#define    RTL8367C_ACT95_GPIO_MASK    0x2000
-#define    RTL8367C_ACT95_FORWARD_OFFSET    12
-#define    RTL8367C_ACT95_FORWARD_MASK    0x1000
-#define    RTL8367C_ACT95_POLICING_OFFSET    11
-#define    RTL8367C_ACT95_POLICING_MASK    0x800
-#define    RTL8367C_ACT95_PRIORITY_OFFSET    10
-#define    RTL8367C_ACT95_PRIORITY_MASK    0x400
-#define    RTL8367C_ACT95_SVID_OFFSET    9
-#define    RTL8367C_ACT95_SVID_MASK    0x200
-#define    RTL8367C_ACT95_CVID_OFFSET    8
-#define    RTL8367C_ACT95_CVID_MASK    0x100
-#define    RTL8367C_OP94_NOT_OFFSET    6
-#define    RTL8367C_OP94_NOT_MASK    0x40
-#define    RTL8367C_ACT94_GPIO_OFFSET    5
-#define    RTL8367C_ACT94_GPIO_MASK    0x20
-#define    RTL8367C_ACT94_FORWARD_OFFSET    4
-#define    RTL8367C_ACT94_FORWARD_MASK    0x10
-#define    RTL8367C_ACT94_POLICING_OFFSET    3
-#define    RTL8367C_ACT94_POLICING_MASK    0x8
-#define    RTL8367C_ACT94_PRIORITY_OFFSET    2
-#define    RTL8367C_ACT94_PRIORITY_MASK    0x4
-#define    RTL8367C_ACT94_SVID_OFFSET    1
-#define    RTL8367C_ACT94_SVID_MASK    0x2
-#define    RTL8367C_ACT94_CVID_OFFSET    0
-#define    RTL8367C_ACT94_CVID_MASK    0x1
-
-/* (16'h0700)cvlan_reg */
-
-#define    RTL8367C_REG_VLAN_PVID_CTRL0    0x0700
-#define    RTL8367C_PORT1_VIDX_OFFSET    8
-#define    RTL8367C_PORT1_VIDX_MASK    0x1F00
-#define    RTL8367C_PORT0_VIDX_OFFSET    0
-#define    RTL8367C_PORT0_VIDX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PVID_CTRL1    0x0701
-#define    RTL8367C_PORT3_VIDX_OFFSET    8
-#define    RTL8367C_PORT3_VIDX_MASK    0x1F00
-#define    RTL8367C_PORT2_VIDX_OFFSET    0
-#define    RTL8367C_PORT2_VIDX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PVID_CTRL2    0x0702
-#define    RTL8367C_PORT5_VIDX_OFFSET    8
-#define    RTL8367C_PORT5_VIDX_MASK    0x1F00
-#define    RTL8367C_PORT4_VIDX_OFFSET    0
-#define    RTL8367C_PORT4_VIDX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PVID_CTRL3    0x0703
-#define    RTL8367C_PORT7_VIDX_OFFSET    8
-#define    RTL8367C_PORT7_VIDX_MASK    0x1F00
-#define    RTL8367C_PORT6_VIDX_OFFSET    0
-#define    RTL8367C_PORT6_VIDX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PVID_CTRL4    0x0704
-#define    RTL8367C_PORT9_VIDX_OFFSET    8
-#define    RTL8367C_PORT9_VIDX_MASK    0x1F00
-#define    RTL8367C_PORT8_VIDX_OFFSET    0
-#define    RTL8367C_PORT8_VIDX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PVID_CTRL5    0x0705
-#define    RTL8367C_VLAN_PVID_CTRL5_OFFSET    0
-#define    RTL8367C_VLAN_PVID_CTRL5_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB0_VALID    0x0708
-#define    RTL8367C_VLAN_PPB0_VALID_VALID_EXT_OFFSET    8
-#define    RTL8367C_VLAN_PPB0_VALID_VALID_EXT_MASK    0x700
-#define    RTL8367C_VLAN_PPB0_VALID_VALID_OFFSET    0
-#define    RTL8367C_VLAN_PPB0_VALID_VALID_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_PPB0_CTRL0    0x0709
-#define    RTL8367C_VLAN_PPB0_CTRL0_PORT2_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB0_CTRL0_PORT2_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB0_CTRL0_PORT1_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB0_CTRL0_PORT1_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB0_CTRL0_PORT0_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB0_CTRL0_PORT0_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB0_CTRL1    0x070a
-#define    RTL8367C_VLAN_PPB0_CTRL1_PORT5_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB0_CTRL1_PORT5_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB0_CTRL1_PORT4_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB0_CTRL1_PORT4_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB0_CTRL1_PORT3_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB0_CTRL1_PORT3_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB0_CTRL2    0x070b
-#define    RTL8367C_VLAN_PPB0_CTRL2_FRAME_TYPE_OFFSET    10
-#define    RTL8367C_VLAN_PPB0_CTRL2_FRAME_TYPE_MASK    0xC00
-#define    RTL8367C_VLAN_PPB0_CTRL2_PORT7_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB0_CTRL2_PORT7_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB0_CTRL2_PORT6_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB0_CTRL2_PORT6_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB0_CTRL4    0x070c
-#define    RTL8367C_VLAN_PPB0_CTRL4_PORT10_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB0_CTRL4_PORT10_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB0_CTRL4_PORT9_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB0_CTRL4_PORT9_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB0_CTRL4_PORT8_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB0_CTRL4_PORT8_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB0_CTRL3    0x070f
-
-#define    RTL8367C_REG_VLAN_PPB1_VALID    0x0710
-#define    RTL8367C_VLAN_PPB1_VALID_VALID_EXT_OFFSET    8
-#define    RTL8367C_VLAN_PPB1_VALID_VALID_EXT_MASK    0x700
-#define    RTL8367C_VLAN_PPB1_VALID_VALID_OFFSET    0
-#define    RTL8367C_VLAN_PPB1_VALID_VALID_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_PPB1_CTRL0    0x0711
-#define    RTL8367C_VLAN_PPB1_CTRL0_PORT2_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB1_CTRL0_PORT2_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB1_CTRL0_PORT1_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB1_CTRL0_PORT1_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB1_CTRL0_PORT0_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB1_CTRL0_PORT0_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB1_CTRL1    0x0712
-#define    RTL8367C_VLAN_PPB1_CTRL1_PORT5_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB1_CTRL1_PORT5_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB1_CTRL1_PORT4_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB1_CTRL1_PORT4_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB1_CTRL1_PORT3_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB1_CTRL1_PORT3_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB1_CTRL2    0x0713
-#define    RTL8367C_VLAN_PPB1_CTRL2_FRAME_TYPE_OFFSET    10
-#define    RTL8367C_VLAN_PPB1_CTRL2_FRAME_TYPE_MASK    0xC00
-#define    RTL8367C_VLAN_PPB1_CTRL2_PORT7_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB1_CTRL2_PORT7_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB1_CTRL2_PORT6_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB1_CTRL2_PORT6_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB1_CTRL4    0x0714
-#define    RTL8367C_VLAN_PPB1_CTRL4_PORT10_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB1_CTRL4_PORT10_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB1_CTRL4_PORT9_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB1_CTRL4_PORT9_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB1_CTRL4_PORT8_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB1_CTRL4_PORT8_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB1_CTRL3    0x0717
-
-#define    RTL8367C_REG_VLAN_PPB2_VALID    0x0718
-#define    RTL8367C_VLAN_PPB2_VALID_VALID_EXT_OFFSET    8
-#define    RTL8367C_VLAN_PPB2_VALID_VALID_EXT_MASK    0x700
-#define    RTL8367C_VLAN_PPB2_VALID_VALID_OFFSET    0
-#define    RTL8367C_VLAN_PPB2_VALID_VALID_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_PPB2_CTRL0    0x0719
-#define    RTL8367C_VLAN_PPB2_CTRL0_PORT2_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB2_CTRL0_PORT2_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB2_CTRL0_PORT1_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB2_CTRL0_PORT1_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB2_CTRL0_PORT0_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB2_CTRL0_PORT0_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB2_CTRL1    0x071a
-#define    RTL8367C_VLAN_PPB2_CTRL1_PORT5_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB2_CTRL1_PORT5_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB2_CTRL1_PORT4_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB2_CTRL1_PORT4_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB2_CTRL1_PORT3_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB2_CTRL1_PORT3_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB2_CTRL2    0x071b
-#define    RTL8367C_VLAN_PPB2_CTRL2_FRAME_TYPE_OFFSET    10
-#define    RTL8367C_VLAN_PPB2_CTRL2_FRAME_TYPE_MASK    0xC00
-#define    RTL8367C_VLAN_PPB2_CTRL2_PORT7_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB2_CTRL2_PORT7_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB2_CTRL2_PORT6_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB2_CTRL2_PORT6_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB2_CTRL4    0x071c
-#define    RTL8367C_VLAN_PPB2_CTRL4_PORT10_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB2_CTRL4_PORT10_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB2_CTRL4_PORT9_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB2_CTRL4_PORT9_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB2_CTRL4_PORT8_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB2_CTRL4_PORT8_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB2_CTRL3    0x071f
-
-#define    RTL8367C_REG_VLAN_PPB3_VALID    0x0720
-#define    RTL8367C_VLAN_PPB3_VALID_VALID_EXT_OFFSET    8
-#define    RTL8367C_VLAN_PPB3_VALID_VALID_EXT_MASK    0x700
-#define    RTL8367C_VLAN_PPB3_VALID_VALID_OFFSET    0
-#define    RTL8367C_VLAN_PPB3_VALID_VALID_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_PPB3_CTRL0    0x0721
-#define    RTL8367C_VLAN_PPB3_CTRL0_PORT2_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB3_CTRL0_PORT2_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB3_CTRL0_PORT1_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB3_CTRL0_PORT1_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB3_CTRL0_PORT0_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB3_CTRL0_PORT0_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB3_CTRL1    0x0722
-#define    RTL8367C_VLAN_PPB3_CTRL1_PORT5_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB3_CTRL1_PORT5_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB3_CTRL1_PORT4_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB3_CTRL1_PORT4_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB3_CTRL1_PORT3_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB3_CTRL1_PORT3_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB3_CTRL2    0x0723
-#define    RTL8367C_VLAN_PPB3_CTRL2_FRAME_TYPE_OFFSET    10
-#define    RTL8367C_VLAN_PPB3_CTRL2_FRAME_TYPE_MASK    0xC00
-#define    RTL8367C_VLAN_PPB3_CTRL2_PORT7_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB3_CTRL2_PORT7_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB3_CTRL2_PORT6_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB3_CTRL2_PORT6_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB3_CTRL4    0x0724
-#define    RTL8367C_VLAN_PPB3_CTRL4_PORT10_INDEX_OFFSET    10
-#define    RTL8367C_VLAN_PPB3_CTRL4_PORT10_INDEX_MASK    0x7C00
-#define    RTL8367C_VLAN_PPB3_CTRL4_PORT9_INDEX_OFFSET    5
-#define    RTL8367C_VLAN_PPB3_CTRL4_PORT9_INDEX_MASK    0x3E0
-#define    RTL8367C_VLAN_PPB3_CTRL4_PORT8_INDEX_OFFSET    0
-#define    RTL8367C_VLAN_PPB3_CTRL4_PORT8_INDEX_MASK    0x1F
-
-#define    RTL8367C_REG_VLAN_PPB3_CTRL3    0x0727
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION0_CTRL0    0x0728
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION0_CTRL1    0x0729
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION0_CTRL2    0x072a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION0_CTRL3    0x072b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION0_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION1_CTRL0    0x072c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION1_CTRL1    0x072d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION1_CTRL2    0x072e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION1_CTRL3    0x072f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION1_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION2_CTRL0    0x0730
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION2_CTRL1    0x0731
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION2_CTRL2    0x0732
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION2_CTRL3    0x0733
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION2_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION3_CTRL0    0x0734
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION3_CTRL1    0x0735
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION3_CTRL2    0x0736
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION3_CTRL3    0x0737
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION3_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION4_CTRL0    0x0738
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION4_CTRL1    0x0739
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION4_CTRL2    0x073a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION4_CTRL3    0x073b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION4_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION5_CTRL0    0x073c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION5_CTRL1    0x073d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION5_CTRL2    0x073e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION5_CTRL3    0x073f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION5_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION6_CTRL0    0x0740
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION6_CTRL1    0x0741
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION6_CTRL2    0x0742
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION6_CTRL3    0x0743
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION6_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION7_CTRL0    0x0744
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION7_CTRL1    0x0745
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION7_CTRL2    0x0746
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION7_CTRL3    0x0747
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION7_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION8_CTRL0    0x0748
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION8_CTRL1    0x0749
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION8_CTRL2    0x074a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION8_CTRL3    0x074b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION8_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION9_CTRL0    0x074c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION9_CTRL1    0x074d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION9_CTRL2    0x074e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION9_CTRL3    0x074f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION9_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION10_CTRL0    0x0750
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION10_CTRL1    0x0751
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION10_CTRL2    0x0752
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION10_CTRL3    0x0753
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION10_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION11_CTRL0    0x0754
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION11_CTRL1    0x0755
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION11_CTRL2    0x0756
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION11_CTRL3    0x0757
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION11_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION12_CTRL0    0x0758
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION12_CTRL1    0x0759
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION12_CTRL2    0x075a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION12_CTRL3    0x075b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION12_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION13_CTRL0    0x075c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION13_CTRL1    0x075d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION13_CTRL2    0x075e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION13_CTRL3    0x075f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION13_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION14_CTRL0    0x0760
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION14_CTRL1    0x0761
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION14_CTRL2    0x0762
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION14_CTRL3    0x0763
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION14_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION15_CTRL0    0x0764
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION15_CTRL1    0x0765
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION15_CTRL2    0x0766
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION15_CTRL3    0x0767
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION15_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION16_CTRL0    0x0768
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION16_CTRL1    0x0769
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION16_CTRL2    0x076a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION16_CTRL3    0x076b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION16_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION17_CTRL0    0x076c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION17_CTRL1    0x076d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION17_CTRL2    0x076e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION17_CTRL3    0x076f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION17_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION18_CTRL0    0x0770
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION18_CTRL1    0x0771
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION18_CTRL2    0x0772
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION18_CTRL3    0x0773
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION18_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION19_CTRL0    0x0774
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION19_CTRL1    0x0775
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION19_CTRL2    0x0776
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION19_CTRL3    0x0777
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION19_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION20_CTRL0    0x0778
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION20_CTRL1    0x0779
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION20_CTRL2    0x077a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION20_CTRL3    0x077b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION20_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION21_CTRL0    0x077c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION21_CTRL1    0x077d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION21_CTRL2    0x077e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION21_CTRL3    0x077f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION21_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION22_CTRL0    0x0780
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION22_CTRL1    0x0781
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION22_CTRL2    0x0782
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION22_CTRL3    0x0783
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION22_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION23_CTRL0    0x0784
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION23_CTRL1    0x0785
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION23_CTRL2    0x0786
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION23_CTRL3    0x0787
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION23_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION24_CTRL0    0x0788
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION24_CTRL1    0x0789
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION24_CTRL2    0x078a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION24_CTRL3    0x078b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION24_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION25_CTRL0    0x078c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION25_CTRL1    0x078d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION25_CTRL2    0x078e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION25_CTRL3    0x078f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION25_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION26_CTRL0    0x0790
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION26_CTRL1    0x0791
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION26_CTRL2    0x0792
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION26_CTRL3    0x0793
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION26_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION27_CTRL0    0x0794
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION27_CTRL1    0x0795
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION27_CTRL2    0x0796
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION27_CTRL3    0x0797
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION27_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION28_CTRL0    0x0798
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION28_CTRL1    0x0799
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION28_CTRL2    0x079a
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION28_CTRL3    0x079b
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION28_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION29_CTRL0    0x079c
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION29_CTRL1    0x079d
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION29_CTRL2    0x079e
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION29_CTRL3    0x079f
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION29_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION30_CTRL0    0x07a0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION30_CTRL1    0x07a1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION30_CTRL2    0x07a2
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION30_CTRL3    0x07a3
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION30_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION31_CTRL0    0x07a4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL0_MBR_EXT_OFFSET    8
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL0_MBR_EXT_MASK    0x700
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL0_MBR_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL0_MBR_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION31_CTRL1    0x07a5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL1_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION31_CTRL2    0x07a6
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_METERIDX_EXT_OFFSET    10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_METERIDX_EXT_MASK    0x400
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_METERIDX_OFFSET    5
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_METERIDX_MASK    0x3E0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_ENVLANPOL_OFFSET    4
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_ENVLANPOL_MASK    0x10
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_VBPRI_OFFSET    1
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_VBPRI_MASK    0xE
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_VBPEN_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL2_VBPEN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_MEMBER_CONFIGURATION31_CTRL3    0x07a7
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_MEMBER_CONFIGURATION31_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_VLAN_CTRL    0x07a8
-#define    RTL8367C_VLAN_CTRL_OFFSET    0
-#define    RTL8367C_VLAN_CTRL_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_INGRESS    0x07a9
-#define    RTL8367C_VLAN_INGRESS_OFFSET    0
-#define    RTL8367C_VLAN_INGRESS_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_ACCEPT_FRAME_TYPE_CTRL0    0x07aa
-#define    RTL8367C_PORT7_FRAME_TYPE_OFFSET    14
-#define    RTL8367C_PORT7_FRAME_TYPE_MASK    0xC000
-#define    RTL8367C_PORT6_FRAME_TYPE_OFFSET    12
-#define    RTL8367C_PORT6_FRAME_TYPE_MASK    0x3000
-#define    RTL8367C_PORT5_FRAME_TYPE_OFFSET    10
-#define    RTL8367C_PORT5_FRAME_TYPE_MASK    0xC00
-#define    RTL8367C_PORT4_FRAME_TYPE_OFFSET    8
-#define    RTL8367C_PORT4_FRAME_TYPE_MASK    0x300
-#define    RTL8367C_PORT3_FRAME_TYPE_OFFSET    6
-#define    RTL8367C_PORT3_FRAME_TYPE_MASK    0xC0
-#define    RTL8367C_PORT2_FRAME_TYPE_OFFSET    4
-#define    RTL8367C_PORT2_FRAME_TYPE_MASK    0x30
-#define    RTL8367C_PORT1_FRAME_TYPE_OFFSET    2
-#define    RTL8367C_PORT1_FRAME_TYPE_MASK    0xC
-#define    RTL8367C_PORT0_FRAME_TYPE_OFFSET    0
-#define    RTL8367C_PORT0_FRAME_TYPE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_ACCEPT_FRAME_TYPE_CTRL1    0x07ab
-#define    RTL8367C_PORT10_FRAME_TYPE_OFFSET    4
-#define    RTL8367C_PORT10_FRAME_TYPE_MASK    0x30
-#define    RTL8367C_PORT9_FRAME_TYPE_OFFSET    2
-#define    RTL8367C_PORT9_FRAME_TYPE_MASK    0xC
-#define    RTL8367C_PORT8_FRAME_TYPE_OFFSET    0
-#define    RTL8367C_PORT8_FRAME_TYPE_MASK    0x3
-
-#define    RTL8367C_REG_PORT_PBFIDEN    0x07ac
-#define    RTL8367C_PORT_PBFIDEN_OFFSET    0
-#define    RTL8367C_PORT_PBFIDEN_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT0_PBFID    0x07ad
-#define    RTL8367C_PORT0_PBFID_OFFSET    0
-#define    RTL8367C_PORT0_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT1_PBFID    0x07ae
-#define    RTL8367C_PORT1_PBFID_OFFSET    0
-#define    RTL8367C_PORT1_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT2_PBFID    0x07af
-#define    RTL8367C_PORT2_PBFID_OFFSET    0
-#define    RTL8367C_PORT2_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT3_PBFID    0x07b0
-#define    RTL8367C_PORT3_PBFID_OFFSET    0
-#define    RTL8367C_PORT3_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT4_PBFID    0x07b1
-#define    RTL8367C_PORT4_PBFID_OFFSET    0
-#define    RTL8367C_PORT4_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT5_PBFID    0x07b2
-#define    RTL8367C_PORT5_PBFID_OFFSET    0
-#define    RTL8367C_PORT5_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT6_PBFID    0x07b3
-#define    RTL8367C_PORT6_PBFID_OFFSET    0
-#define    RTL8367C_PORT6_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT7_PBFID    0x07b4
-#define    RTL8367C_PORT7_PBFID_OFFSET    0
-#define    RTL8367C_PORT7_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_VLAN_EXT_CTRL    0x07b5
-#define    RTL8367C_VLAN_1P_REMARK_BYPASS_REALKEEP_OFFSET    2
-#define    RTL8367C_VLAN_1P_REMARK_BYPASS_REALKEEP_MASK    0x4
-#define    RTL8367C_VLAN_VID4095_TYPE_OFFSET    1
-#define    RTL8367C_VLAN_VID4095_TYPE_MASK    0x2
-#define    RTL8367C_VLAN_VID0_TYPE_OFFSET    0
-#define    RTL8367C_VLAN_VID0_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_EXT_CTRL2    0x07b6
-#define    RTL8367C_VLAN_EXT_CTRL2_OFFSET    0
-#define    RTL8367C_VLAN_EXT_CTRL2_MASK    0x1
-
-#define    RTL8367C_REG_PORT8_PBFID    0x07b7
-#define    RTL8367C_PORT8_PBFID_OFFSET    0
-#define    RTL8367C_PORT8_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT9_PBFID    0x07b8
-#define    RTL8367C_PORT9_PBFID_OFFSET    0
-#define    RTL8367C_PORT9_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_PORT10_PBFID    0x07b9
-#define    RTL8367C_PORT10_PBFID_OFFSET    0
-#define    RTL8367C_PORT10_PBFID_MASK    0xF
-
-#define    RTL8367C_REG_CVLAN_DUMMY00    0x07E0
-
-#define    RTL8367C_REG_CVLAN_DUMMY01    0x07E1
-
-#define    RTL8367C_REG_CVLAN_DUMMY02    0x07E2
-
-#define    RTL8367C_REG_CVLAN_DUMMY03    0x07E3
-
-#define    RTL8367C_REG_CVLAN_DUMMY04    0x07E4
-
-#define    RTL8367C_REG_CVLAN_DUMMY05    0x07E5
-
-#define    RTL8367C_REG_CVLAN_DUMMY06    0x07E6
-
-#define    RTL8367C_REG_CVLAN_DUMMY07    0x07E7
-
-#define    RTL8367C_REG_CVLAN_DUMMY08    0x07E8
-
-#define    RTL8367C_REG_CVLAN_DUMMY09    0x07E9
-
-#define    RTL8367C_REG_CVLAN_DUMMY10    0x07EA
-
-#define    RTL8367C_REG_CVLAN_DUMMY11    0x07EB
-
-#define    RTL8367C_REG_CVLAN_DUMMY12    0x07EC
-
-#define    RTL8367C_REG_CVLAN_DUMMY13    0x07ED
-
-#define    RTL8367C_REG_CVLAN_DUMMY14    0x07EE
-
-#define    RTL8367C_REG_CVLAN_DUMMY15    0x07EF
-
-/* (16'h0800)dpm_reg */
-
-#define    RTL8367C_REG_RMA_CTRL00    0x0800
-#define    RTL8367C_RMA_CTRL00_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL00_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL00_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL00_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_TRAP_PRIORITY_OFFSET    3
-#define    RTL8367C_TRAP_PRIORITY_MASK    0x38
-#define    RTL8367C_RMA_CTRL00_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL00_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL00_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL00_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL00_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL00_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL01    0x0801
-#define    RTL8367C_RMA_CTRL01_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL01_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL01_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL01_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL01_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL01_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL01_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL01_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL01_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL01_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL02    0x0802
-#define    RTL8367C_RMA_CTRL02_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL02_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL02_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL02_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL02_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL02_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL02_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL02_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL02_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL02_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL03    0x0803
-#define    RTL8367C_RMA_CTRL03_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL03_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL03_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL03_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL03_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL03_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL03_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL03_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL03_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL03_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL04    0x0804
-#define    RTL8367C_RMA_CTRL04_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL04_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL04_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL04_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL04_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL04_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL04_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL04_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL04_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL04_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL08    0x0808
-#define    RTL8367C_RMA_CTRL08_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL08_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL08_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL08_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL08_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL08_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL08_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL08_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL08_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL08_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL0D    0x080d
-#define    RTL8367C_RMA_CTRL0D_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL0D_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL0D_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL0D_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL0D_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL0D_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL0D_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL0D_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL0D_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL0D_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL0E    0x080e
-#define    RTL8367C_RMA_CTRL0E_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL0E_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL0E_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL0E_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL0E_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL0E_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL0E_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL0E_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL0E_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL0E_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL10    0x0810
-#define    RTL8367C_RMA_CTRL10_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL10_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL10_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL10_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL10_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL10_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL10_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL10_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL10_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL10_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL11    0x0811
-#define    RTL8367C_RMA_CTRL11_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL11_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL11_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL11_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL11_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL11_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL11_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL11_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL11_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL11_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL12    0x0812
-#define    RTL8367C_RMA_CTRL12_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL12_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL12_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL12_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL12_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL12_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL12_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL12_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL12_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL12_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL13    0x0813
-#define    RTL8367C_RMA_CTRL13_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL13_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL13_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL13_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL13_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL13_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL13_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL13_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL13_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL13_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL18    0x0818
-#define    RTL8367C_RMA_CTRL18_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL18_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL18_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL18_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL18_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL18_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL18_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL18_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL18_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL18_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL1A    0x081a
-#define    RTL8367C_RMA_CTRL1A_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL1A_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL1A_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL1A_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL1A_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL1A_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL1A_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL1A_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL1A_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL1A_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL20    0x0820
-#define    RTL8367C_RMA_CTRL20_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL20_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL20_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL20_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL20_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL20_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL20_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL20_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL20_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL20_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL21    0x0821
-#define    RTL8367C_RMA_CTRL21_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL21_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL21_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL21_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL21_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL21_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL21_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL21_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL21_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL21_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL22    0x0822
-#define    RTL8367C_RMA_CTRL22_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL22_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL22_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL22_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL22_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL22_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL22_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL22_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL22_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL22_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL_CDP    0x0830
-#define    RTL8367C_RMA_CTRL_CDP_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL_CDP_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL_CDP_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL_CDP_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL_CDP_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL_CDP_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL_CDP_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL_CDP_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL_CDP_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL_CDP_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL_CSSTP    0x0831
-#define    RTL8367C_RMA_CTRL_CSSTP_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL_CSSTP_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL_CSSTP_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL_CSSTP_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL_CSSTP_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL_CSSTP_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL_CSSTP_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL_CSSTP_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL_CSSTP_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL_CSSTP_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_CTRL_LLDP    0x0832
-#define    RTL8367C_RMA_CTRL_LLDP_OPERATION_OFFSET    7
-#define    RTL8367C_RMA_CTRL_LLDP_OPERATION_MASK    0x180
-#define    RTL8367C_RMA_CTRL_LLDP_DISCARD_STORM_FILTER_OFFSET    6
-#define    RTL8367C_RMA_CTRL_LLDP_DISCARD_STORM_FILTER_MASK    0x40
-#define    RTL8367C_RMA_CTRL_LLDP_KEEP_FORMAT_OFFSET    2
-#define    RTL8367C_RMA_CTRL_LLDP_KEEP_FORMAT_MASK    0x4
-#define    RTL8367C_RMA_CTRL_LLDP_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_RMA_CTRL_LLDP_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_RMA_CTRL_LLDP_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_RMA_CTRL_LLDP_PORTISO_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_RMA_LLDP_EN    0x0833
-#define    RTL8367C_RMA_LLDP_EN_OFFSET    0
-#define    RTL8367C_RMA_LLDP_EN_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_PORTBASED_PRIORITY_CTRL0    0x0851
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT3_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT3_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT2_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT2_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT1_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT1_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT0_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL0_PORT0_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PORTBASED_PRIORITY_CTRL1    0x0852
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT7_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT7_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT6_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT6_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT5_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT5_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT4_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL1_PORT4_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PORTBASED_PRIORITY_CTRL2    0x0853
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL2_PORT10_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL2_PORT10_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL2_PORT9_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL2_PORT9_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL2_PORT8_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PORTBASED_PRIORITY_CTRL2_PORT8_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM0_CTRL0    0x0855
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT3_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT3_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT2_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT2_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT1_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT1_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT0_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL0_PORT0_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM0_CTRL1    0x0856
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT7_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT7_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT6_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT6_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT5_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT5_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT4_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL1_PORT4_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM0_CTRL2    0x0857
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL2_PORT10_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL2_PORT10_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL2_PORT9_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL2_PORT9_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL2_PORT8_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM0_CTRL2_PORT8_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM1_CTRL0    0x0859
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT3_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT3_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT2_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT2_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT1_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT1_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT0_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL0_PORT0_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM1_CTRL1    0x085a
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT7_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT7_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT6_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT6_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT5_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT5_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT4_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL1_PORT4_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM1_CTRL2    0x085b
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL2_PORT10_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL2_PORT10_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL2_PORT9_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL2_PORT9_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL2_PORT8_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM1_CTRL2_PORT8_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM2_CTRL0    0x085d
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT3_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT3_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT2_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT2_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT1_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT1_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT0_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL0_PORT0_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM2_CTRL1    0x085e
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT7_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT7_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT6_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT6_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT5_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT5_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT4_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL1_PORT4_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM2_CTRL2    0x085f
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL2_PORT10_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL2_PORT10_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL2_PORT9_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL2_PORT9_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL2_PORT8_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM2_CTRL2_PORT8_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM3_CTRL0    0x0861
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT3_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT3_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT2_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT2_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT1_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT1_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT0_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL0_PORT0_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM3_CTRL1    0x0862
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT7_PRIORITY_OFFSET    12
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT7_PRIORITY_MASK    0x7000
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT6_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT6_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT5_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT5_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT4_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL1_PORT4_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_PPB_PRIORITY_ITEM3_CTRL2    0x0863
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL2_PORT10_PRIORITY_OFFSET    8
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL2_PORT10_PRIORITY_MASK    0x700
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL2_PORT9_PRIORITY_OFFSET    4
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL2_PORT9_PRIORITY_MASK    0x70
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL2_PORT8_PRIORITY_OFFSET    0
-#define    RTL8367C_VLAN_PPB_PRIORITY_ITEM3_CTRL2_PORT8_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_1Q_PRIORITY_REMAPPING_CTRL0    0x0865
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY3_OFFSET    12
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY3_MASK    0x7000
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY2_OFFSET    8
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY2_MASK    0x700
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY1_OFFSET    4
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY1_MASK    0x70
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY0_OFFSET    0
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL0_PRIORITY0_MASK    0x7
-
-#define    RTL8367C_REG_QOS_1Q_PRIORITY_REMAPPING_CTRL1    0x0866
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY7_OFFSET    12
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY7_MASK    0x7000
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY6_OFFSET    8
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY6_MASK    0x700
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY5_OFFSET    4
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY5_MASK    0x70
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY4_OFFSET    0
-#define    RTL8367C_QOS_1Q_PRIORITY_REMAPPING_CTRL1_PRIORITY4_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL0    0x0867
-#define    RTL8367C_DSCP3_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP3_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP2_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP2_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP1_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP1_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP0_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP0_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL1    0x0868
-#define    RTL8367C_DSCP7_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP7_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP6_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP6_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP5_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP5_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP4_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP4_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL2    0x0869
-#define    RTL8367C_DSCP11_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP11_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP10_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP10_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP9_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP9_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP8_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP8_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL3    0x086a
-#define    RTL8367C_DSCP15_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP15_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP14_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP14_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP13_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP13_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP12_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP12_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL4    0x086b
-#define    RTL8367C_DSCP19_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP19_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP18_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP18_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP17_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP17_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP16_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP16_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL5    0x086c
-#define    RTL8367C_DSCP23_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP23_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP22_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP22_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP21_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP21_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP20_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP20_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL6    0x086d
-#define    RTL8367C_DSCP27_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP27_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP26_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP26_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP25_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP25_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP24_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP24_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL7    0x086e
-#define    RTL8367C_DSCP31_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP31_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP30_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP30_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP29_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP29_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP28_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP28_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL8    0x086f
-#define    RTL8367C_DSCP35_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP35_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP34_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP34_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP33_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP33_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP32_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP32_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL9    0x0870
-#define    RTL8367C_DSCP39_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP39_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP38_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP38_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP37_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP37_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP36_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP36_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL10    0x0871
-#define    RTL8367C_DSCP43_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP43_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP42_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP42_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP41_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP41_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP40_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP40_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL11    0x0872
-#define    RTL8367C_DSCP47_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP47_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP46_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP46_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP45_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP45_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP44_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP44_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL12    0x0873
-#define    RTL8367C_DSCP51_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP51_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP50_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP50_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP49_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP49_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP48_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP48_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL13    0x0874
-#define    RTL8367C_DSCP55_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP55_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP54_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP54_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP53_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP53_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP52_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP52_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL14    0x0875
-#define    RTL8367C_DSCP59_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP59_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP58_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP58_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP57_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP57_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP56_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP56_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_DSCP_TO_PRIORITY_CTRL15    0x0876
-#define    RTL8367C_DSCP63_PRIORITY_OFFSET    12
-#define    RTL8367C_DSCP63_PRIORITY_MASK    0x7000
-#define    RTL8367C_DSCP62_PRIORITY_OFFSET    8
-#define    RTL8367C_DSCP62_PRIORITY_MASK    0x700
-#define    RTL8367C_DSCP61_PRIORITY_OFFSET    4
-#define    RTL8367C_DSCP61_PRIORITY_MASK    0x70
-#define    RTL8367C_DSCP60_PRIORITY_OFFSET    0
-#define    RTL8367C_DSCP60_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_PORTBASED_PRIORITY_CTRL0    0x0877
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT3_PRIORITY_OFFSET    12
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT3_PRIORITY_MASK    0x7000
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT2_PRIORITY_OFFSET    8
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT2_PRIORITY_MASK    0x700
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT1_PRIORITY_OFFSET    4
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT1_PRIORITY_MASK    0x70
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT0_PRIORITY_OFFSET    0
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL0_PORT0_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_PORTBASED_PRIORITY_CTRL1    0x0878
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT7_PRIORITY_OFFSET    12
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT7_PRIORITY_MASK    0x7000
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT6_PRIORITY_OFFSET    8
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT6_PRIORITY_MASK    0x700
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT5_PRIORITY_OFFSET    4
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT5_PRIORITY_MASK    0x70
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT4_PRIORITY_OFFSET    0
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL1_PORT4_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_DUMMY0879    0x0879
-#define    RTL8367C_DUMMY0879_OFFSET    0
-#define    RTL8367C_DUMMY0879_MASK    0x1
-
-#define    RTL8367C_REG_QOS_PORTBASED_PRIORITY_CTRL2    0x087a
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL2_PORT10_PRIORITY_OFFSET    8
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL2_PORT10_PRIORITY_MASK    0x700
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL2_PORT9_PRIORITY_OFFSET    4
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL2_PORT9_PRIORITY_MASK    0x70
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL2_PORT8_PRIORITY_OFFSET    0
-#define    RTL8367C_QOS_PORTBASED_PRIORITY_CTRL2_PORT8_PRIORITY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION_CTRL0    0x087b
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL0_QOS_ACL_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL0_QOS_ACL_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL0_QOS_PORT_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL0_QOS_PORT_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION_CTRL1    0x087c
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL1_QOS_DOT1Q_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL1_QOS_DOT1Q_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL1_QOS_DSCP_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL1_QOS_DSCP_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION_CTRL2    0x087d
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL2_QOS_CVLAN_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL2_QOS_CVLAN_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL2_QOS_SVLAN_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL2_QOS_SVLAN_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION_CTRL3    0x087e
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL3_QOS_SA_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL3_QOS_SA_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL3_QOS_LUTFWD_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_CTRL3_QOS_LUTFWD_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0    0x087f
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY3_OFFSET    12
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY3_MASK    0x7000
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY2_OFFSET    8
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY2_MASK    0x700
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY1_OFFSET    4
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY1_MASK    0x70
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY0_OFFSET    0
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL0_PRIORITY0_MASK    0x7
-
-#define    RTL8367C_REG_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1    0x0880
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY7_OFFSET    12
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY7_MASK    0x7000
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY6_OFFSET    8
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY6_MASK    0x700
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY5_OFFSET    4
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY5_MASK    0x70
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY4_OFFSET    0
-#define    RTL8367C_QOS_PRIORITY_REMAPPING_IN_CPU_CTRL1_PRIORITY4_MASK    0x7
-
-#define    RTL8367C_REG_QOS_TRAP_PRIORITY0    0x0881
-#define    RTL8367C_UNKNOWN_MC_PRIORTY_OFFSET    12
-#define    RTL8367C_UNKNOWN_MC_PRIORTY_MASK    0x7000
-#define    RTL8367C_SVLAN_PRIOIRTY_OFFSET    8
-#define    RTL8367C_SVLAN_PRIOIRTY_MASK    0x700
-#define    RTL8367C_OAM_PRIOIRTY_OFFSET    4
-#define    RTL8367C_OAM_PRIOIRTY_MASK    0x70
-#define    RTL8367C_DOT1X_PRIORTY_OFFSET    0
-#define    RTL8367C_DOT1X_PRIORTY_MASK    0x7
-
-#define    RTL8367C_REG_QOS_TRAP_PRIORITY1    0x0882
-#define    RTL8367C_DW8051_TRAP_PRI_OFFSET    4
-#define    RTL8367C_DW8051_TRAP_PRI_MASK    0x70
-#define    RTL8367C_EEELLDP_TRAP_PRI_OFFSET    0
-#define    RTL8367C_EEELLDP_TRAP_PRI_MASK    0x7
-
-#define    RTL8367C_REG_MAX_LENGTH_CFG    0x0883
-#define    RTL8367C_MAX_LENGTH_GIGA_OFFSET    8
-#define    RTL8367C_MAX_LENGTH_GIGA_MASK    0xFF00
-#define    RTL8367C_MAX_LENGTH_10_100M_OFFSET    0
-#define    RTL8367C_MAX_LENGTH_10_100M_MASK    0xFF
-
-#define    RTL8367C_REG_MAX_LEN_RX_TX    0x0884
-#define    RTL8367C_MAX_LEN_RX_TX_OFFSET    0
-#define    RTL8367C_MAX_LEN_RX_TX_MASK    0x3
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION2_CTRL0    0x0885
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL0_QOS_ACL_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL0_QOS_ACL_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL0_QOS_PORT_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL0_QOS_PORT_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION2_CTRL1    0x0886
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL1_QOS_DOT1Q_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL1_QOS_DOT1Q_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL1_QOS_DSCP_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL1_QOS_DSCP_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION2_CTRL2    0x0887
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL2_QOS_CVLAN_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL2_QOS_CVLAN_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL2_QOS_SVLAN_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL2_QOS_SVLAN_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION2_CTRL3    0x0888
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL3_QOS_SA_WEIGHT_OFFSET    8
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL3_QOS_SA_WEIGHT_MASK    0xFF00
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL3_QOS_LUTFWD_WEIGHT_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_CTRL3_QOS_LUTFWD_WEIGHT_MASK    0xFF
-
-#define    RTL8367C_REG_QOS_INTERNAL_PRIORITY_DECISION_IDX    0x0889
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_IDX_OFFSET    0
-#define    RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_IDX_MASK    0x7FF
-
-#define    RTL8367C_REG_MAX_LENGTH_CFG_EXT    0x088a
-#define    RTL8367C_MAX_LENGTH_GIGA_EXT_OFFSET    3
-#define    RTL8367C_MAX_LENGTH_GIGA_EXT_MASK    0x38
-#define    RTL8367C_MAX_LENGTH_10_100M_EXT_OFFSET    0
-#define    RTL8367C_MAX_LENGTH_10_100M_EXT_MASK    0x7
-
-#define    RTL8367C_REG_MAX_LEN_RX_TX_CFG0    0x088c
-#define    RTL8367C_MAX_LEN_RX_TX_CFG0_OFFSET    0
-#define    RTL8367C_MAX_LEN_RX_TX_CFG0_MASK    0x3FFF
-
-#define    RTL8367C_REG_MAX_LEN_RX_TX_CFG1    0x088d
-#define    RTL8367C_MAX_LEN_RX_TX_CFG1_OFFSET    0
-#define    RTL8367C_MAX_LEN_RX_TX_CFG1_MASK    0x3FFF
-
-#define    RTL8367C_REG_UNDA_FLOODING_PMSK    0x0890
-#define    RTL8367C_UNDA_FLOODING_PMSK_OFFSET    0
-#define    RTL8367C_UNDA_FLOODING_PMSK_MASK    0x7FF
-
-#define    RTL8367C_REG_UNMCAST_FLOADING_PMSK    0x0891
-#define    RTL8367C_UNMCAST_FLOADING_PMSK_OFFSET    0
-#define    RTL8367C_UNMCAST_FLOADING_PMSK_MASK    0x7FF
-
-#define    RTL8367C_REG_BCAST_FLOADING_PMSK    0x0892
-#define    RTL8367C_BCAST_FLOADING_PMSK_OFFSET    0
-#define    RTL8367C_BCAST_FLOADING_PMSK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL2    0x08a0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH7_OFFSET    14
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH7_MASK    0xC000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH6_OFFSET    12
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH6_MASK    0x3000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH5_OFFSET    10
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH5_MASK    0xC00
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH4_OFFSET    8
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH4_MASK    0x300
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH3_OFFSET    6
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH3_MASK    0xC0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH2_OFFSET    4
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH2_MASK    0x30
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH1_OFFSET    2
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH1_MASK    0xC
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH0_OFFSET    0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH0_MASK    0x3
-
-#define    RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL3    0x08a1
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH15_OFFSET    14
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH15_MASK    0xC000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH14_OFFSET    12
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH14_MASK    0x3000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH13_OFFSET    10
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH13_MASK    0xC00
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH12_OFFSET    8
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH12_MASK    0x300
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH11_OFFSET    6
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH11_MASK    0xC0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH10_OFFSET    4
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH10_MASK    0x30
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH9_OFFSET    2
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH9_MASK    0xC
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH8_OFFSET    0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH8_MASK    0x3
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT0_MASK    0x08a2
-#define    RTL8367C_PORT_ISOLATION_PORT0_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT0_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT1_MASK    0x08a3
-#define    RTL8367C_PORT_ISOLATION_PORT1_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT1_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT2_MASK    0x08a4
-#define    RTL8367C_PORT_ISOLATION_PORT2_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT2_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT3_MASK    0x08a5
-#define    RTL8367C_PORT_ISOLATION_PORT3_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT3_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT4_MASK    0x08a6
-#define    RTL8367C_PORT_ISOLATION_PORT4_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT4_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT5_MASK    0x08a7
-#define    RTL8367C_PORT_ISOLATION_PORT5_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT5_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT6_MASK    0x08a8
-#define    RTL8367C_PORT_ISOLATION_PORT6_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT6_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT7_MASK    0x08a9
-#define    RTL8367C_PORT_ISOLATION_PORT7_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT7_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT8_MASK    0x08aa
-#define    RTL8367C_PORT_ISOLATION_PORT8_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT8_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT9_MASK    0x08ab
-#define    RTL8367C_PORT_ISOLATION_PORT9_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT9_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_ISOLATION_PORT10_MASK    0x08ac
-#define    RTL8367C_PORT_ISOLATION_PORT10_MASK_OFFSET    0
-#define    RTL8367C_PORT_ISOLATION_PORT10_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_CTRL    0x08b4
-#define    RTL8367C_FORCE_CTRL_OFFSET    0
-#define    RTL8367C_FORCE_CTRL_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT0_MASK    0x08b5
-#define    RTL8367C_FORCE_PORT0_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT0_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT1_MASK    0x08b6
-#define    RTL8367C_FORCE_PORT1_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT1_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT2_MASK    0x08b7
-#define    RTL8367C_FORCE_PORT2_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT2_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT3_MASK    0x08b8
-#define    RTL8367C_FORCE_PORT3_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT3_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT4_MASK    0x08b9
-#define    RTL8367C_FORCE_PORT4_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT4_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT5_MASK    0x08ba
-#define    RTL8367C_FORCE_PORT5_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT5_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT6_MASK    0x08bb
-#define    RTL8367C_FORCE_PORT6_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT6_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT7_MASK    0x08bc
-#define    RTL8367C_FORCE_PORT7_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT7_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT8_MASK    0x08bd
-#define    RTL8367C_FORCE_PORT8_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT8_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT9_MASK    0x08be
-#define    RTL8367C_FORCE_PORT9_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT9_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_FORCE_PORT10_MASK    0x08bf
-#define    RTL8367C_FORCE_PORT10_MASK_OFFSET    0
-#define    RTL8367C_FORCE_PORT10_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_SOURCE_PORT_PERMIT    0x08c5
-#define    RTL8367C_SOURCE_PORT_PERMIT_OFFSET    0
-#define    RTL8367C_SOURCE_PORT_PERMIT_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMCAST_VLAN_LEAKY    0x08c6
-#define    RTL8367C_IPMCAST_VLAN_LEAKY_OFFSET    0
-#define    RTL8367C_IPMCAST_VLAN_LEAKY_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMCAST_PORTISO_LEAKY    0x08c7
-#define    RTL8367C_IPMCAST_PORTISO_LEAKY_OFFSET    0
-#define    RTL8367C_IPMCAST_PORTISO_LEAKY_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_SECURITY_CTRL    0x08c8
-#define    RTL8367C_UNKNOWN_UNICAST_DA_BEHAVE_OFFSET    6
-#define    RTL8367C_UNKNOWN_UNICAST_DA_BEHAVE_MASK    0xC0
-#define    RTL8367C_LUT_LEARN_OVER_ACT_OFFSET    4
-#define    RTL8367C_LUT_LEARN_OVER_ACT_MASK    0x30
-#define    RTL8367C_UNMATCHED_SA_BEHAVE_OFFSET    2
-#define    RTL8367C_UNMATCHED_SA_BEHAVE_MASK    0xC
-#define    RTL8367C_UNKNOWN_SA_BEHAVE_OFFSET    0
-#define    RTL8367C_UNKNOWN_SA_BEHAVE_MASK    0x3
-
-#define    RTL8367C_REG_UNKNOWN_IPV4_MULTICAST_CTRL0    0x08c9
-#define    RTL8367C_PORT7_UNKNOWN_IP4_MCAST_OFFSET    14
-#define    RTL8367C_PORT7_UNKNOWN_IP4_MCAST_MASK    0xC000
-#define    RTL8367C_PORT6_UNKNOWN_IP4_MCAST_OFFSET    12
-#define    RTL8367C_PORT6_UNKNOWN_IP4_MCAST_MASK    0x3000
-#define    RTL8367C_PORT5_UNKNOWN_IP4_MCAST_OFFSET    10
-#define    RTL8367C_PORT5_UNKNOWN_IP4_MCAST_MASK    0xC00
-#define    RTL8367C_PORT4_UNKNOWN_IP4_MCAST_OFFSET    8
-#define    RTL8367C_PORT4_UNKNOWN_IP4_MCAST_MASK    0x300
-#define    RTL8367C_PORT3_UNKNOWN_IP4_MCAST_OFFSET    6
-#define    RTL8367C_PORT3_UNKNOWN_IP4_MCAST_MASK    0xC0
-#define    RTL8367C_PORT2_UNKNOWN_IP4_MCAST_OFFSET    4
-#define    RTL8367C_PORT2_UNKNOWN_IP4_MCAST_MASK    0x30
-#define    RTL8367C_PORT1_UNKNOWN_IP4_MCAST_OFFSET    2
-#define    RTL8367C_PORT1_UNKNOWN_IP4_MCAST_MASK    0xC
-#define    RTL8367C_PORT0_UNKNOWN_IP4_MCAST_OFFSET    0
-#define    RTL8367C_PORT0_UNKNOWN_IP4_MCAST_MASK    0x3
-
-#define    RTL8367C_REG_UNKNOWN_IPV4_MULTICAST_CTRL1    0x08ca
-#define    RTL8367C_PORT10_UNKNOWN_IP4_MCAST_OFFSET    4
-#define    RTL8367C_PORT10_UNKNOWN_IP4_MCAST_MASK    0x30
-#define    RTL8367C_PORT9_UNKNOWN_IP4_MCAST_OFFSET    2
-#define    RTL8367C_PORT9_UNKNOWN_IP4_MCAST_MASK    0xC
-#define    RTL8367C_PORT8_UNKNOWN_IP4_MCAST_OFFSET    0
-#define    RTL8367C_PORT8_UNKNOWN_IP4_MCAST_MASK    0x3
-
-#define    RTL8367C_REG_UNKNOWN_IPV6_MULTICAST_CTRL0    0x08cb
-#define    RTL8367C_PORT7_UNKNOWN_IP6_MCAST_OFFSET    14
-#define    RTL8367C_PORT7_UNKNOWN_IP6_MCAST_MASK    0xC000
-#define    RTL8367C_PORT6_UNKNOWN_IP6_MCAST_OFFSET    12
-#define    RTL8367C_PORT6_UNKNOWN_IP6_MCAST_MASK    0x3000
-#define    RTL8367C_PORT5_UNKNOWN_IP6_MCAST_OFFSET    10
-#define    RTL8367C_PORT5_UNKNOWN_IP6_MCAST_MASK    0xC00
-#define    RTL8367C_PORT4_UNKNOWN_IP6_MCAST_OFFSET    8
-#define    RTL8367C_PORT4_UNKNOWN_IP6_MCAST_MASK    0x300
-#define    RTL8367C_PORT3_UNKNOWN_IP6_MCAST_OFFSET    6
-#define    RTL8367C_PORT3_UNKNOWN_IP6_MCAST_MASK    0xC0
-#define    RTL8367C_PORT2_UNKNOWN_IP6_MCAST_OFFSET    4
-#define    RTL8367C_PORT2_UNKNOWN_IP6_MCAST_MASK    0x30
-#define    RTL8367C_PORT1_UNKNOWN_IP6_MCAST_OFFSET    2
-#define    RTL8367C_PORT1_UNKNOWN_IP6_MCAST_MASK    0xC
-#define    RTL8367C_PORT0_UNKNOWN_IP6_MCAST_OFFSET    0
-#define    RTL8367C_PORT0_UNKNOWN_IP6_MCAST_MASK    0x3
-
-#define    RTL8367C_REG_UNKNOWN_IPV6_MULTICAST_CTRL1    0x08cc
-#define    RTL8367C_PORT10_UNKNOWN_IP6_MCAST_OFFSET    4
-#define    RTL8367C_PORT10_UNKNOWN_IP6_MCAST_MASK    0x30
-#define    RTL8367C_PORT9_UNKNOWN_IP6_MCAST_OFFSET    2
-#define    RTL8367C_PORT9_UNKNOWN_IP6_MCAST_MASK    0xC
-#define    RTL8367C_PORT8_UNKNOWN_IP6_MCAST_OFFSET    0
-#define    RTL8367C_PORT8_UNKNOWN_IP6_MCAST_MASK    0x3
-
-#define    RTL8367C_REG_UNKNOWN_L2_MULTICAST_CTRL0    0x08cd
-#define    RTL8367C_PORT7_UNKNOWN_L2_MCAST_OFFSET    14
-#define    RTL8367C_PORT7_UNKNOWN_L2_MCAST_MASK    0xC000
-#define    RTL8367C_PORT6_UNKNOWN_L2_MCAST_OFFSET    12
-#define    RTL8367C_PORT6_UNKNOWN_L2_MCAST_MASK    0x3000
-#define    RTL8367C_PORT5_UNKNOWN_L2_MCAST_OFFSET    10
-#define    RTL8367C_PORT5_UNKNOWN_L2_MCAST_MASK    0xC00
-#define    RTL8367C_PORT4_UNKNOWN_L2_MCAST_OFFSET    8
-#define    RTL8367C_PORT4_UNKNOWN_L2_MCAST_MASK    0x300
-#define    RTL8367C_PORT3_UNKNOWN_L2_MCAST_OFFSET    6
-#define    RTL8367C_PORT3_UNKNOWN_L2_MCAST_MASK    0xC0
-#define    RTL8367C_PORT2_UNKNOWN_L2_MCAST_OFFSET    4
-#define    RTL8367C_PORT2_UNKNOWN_L2_MCAST_MASK    0x30
-#define    RTL8367C_PORT1_UNKNOWN_L2_MCAST_OFFSET    2
-#define    RTL8367C_PORT1_UNKNOWN_L2_MCAST_MASK    0xC
-#define    RTL8367C_PORT0_UNKNOWN_L2_MCAST_OFFSET    0
-#define    RTL8367C_PORT0_UNKNOWN_L2_MCAST_MASK    0x3
-
-#define    RTL8367C_REG_PORT_TRUNK_DROP_CTRL    0x08ce
-#define    RTL8367C_PORT_TRUNK_DROP_CTRL_OFFSET    0
-#define    RTL8367C_PORT_TRUNK_DROP_CTRL_MASK    0x1
-
-#define    RTL8367C_REG_PORT_TRUNK_CTRL    0x08cf
-#define    RTL8367C_PORT_TRUNK_DUMB_OFFSET    8
-#define    RTL8367C_PORT_TRUNK_DUMB_MASK    0x100
-#define    RTL8367C_PORT_TRUNK_FLOOD_OFFSET    7
-#define    RTL8367C_PORT_TRUNK_FLOOD_MASK    0x80
-#define    RTL8367C_DPORT_HASH_OFFSET    6
-#define    RTL8367C_DPORT_HASH_MASK    0x40
-#define    RTL8367C_SPORT_HASH_OFFSET    5
-#define    RTL8367C_SPORT_HASH_MASK    0x20
-#define    RTL8367C_DIP_HASH_OFFSET    4
-#define    RTL8367C_DIP_HASH_MASK    0x10
-#define    RTL8367C_SIP_HASH_OFFSET    3
-#define    RTL8367C_SIP_HASH_MASK    0x8
-#define    RTL8367C_DMAC_HASH_OFFSET    2
-#define    RTL8367C_DMAC_HASH_MASK    0x4
-#define    RTL8367C_SMAC_HASH_OFFSET    1
-#define    RTL8367C_SMAC_HASH_MASK    0x2
-#define    RTL8367C_SPA_HASH_OFFSET    0
-#define    RTL8367C_SPA_HASH_MASK    0x1
-
-#define    RTL8367C_REG_PORT_TRUNK_GROUP_MASK    0x08d0
-#define    RTL8367C_PORT_TRUNK_GROUP2_MASK_OFFSET    8
-#define    RTL8367C_PORT_TRUNK_GROUP2_MASK_MASK    0x300
-#define    RTL8367C_PORT_TRUNK_GROUP1_MASK_OFFSET    4
-#define    RTL8367C_PORT_TRUNK_GROUP1_MASK_MASK    0xF0
-#define    RTL8367C_PORT_TRUNK_GROUP0_MASK_OFFSET    0
-#define    RTL8367C_PORT_TRUNK_GROUP0_MASK_MASK    0xF
-
-#define    RTL8367C_REG_PORT_TRUNK_FLOWCTRL    0x08d1
-#define    RTL8367C_EN_FLOWCTRL_TG2_OFFSET    2
-#define    RTL8367C_EN_FLOWCTRL_TG2_MASK    0x4
-#define    RTL8367C_EN_FLOWCTRL_TG1_OFFSET    1
-#define    RTL8367C_EN_FLOWCTRL_TG1_MASK    0x2
-#define    RTL8367C_EN_FLOWCTRL_TG0_OFFSET    0
-#define    RTL8367C_EN_FLOWCTRL_TG0_MASK    0x1
-
-#define    RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL0    0x08d2
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH7_OFFSET    14
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH7_MASK    0xC000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH6_OFFSET    12
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH6_MASK    0x3000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH5_OFFSET    10
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH5_MASK    0xC00
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH4_OFFSET    8
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH4_MASK    0x300
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH3_OFFSET    6
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH3_MASK    0xC0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH2_OFFSET    4
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH2_MASK    0x30
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH1_OFFSET    2
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH1_MASK    0xC
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH0_OFFSET    0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH0_MASK    0x3
-
-#define    RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL1    0x08d3
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH15_OFFSET    14
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH15_MASK    0xC000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH14_OFFSET    12
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH14_MASK    0x3000
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH13_OFFSET    10
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH13_MASK    0xC00
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH12_OFFSET    8
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH12_MASK    0x300
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH11_OFFSET    6
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH11_MASK    0xC0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH10_OFFSET    4
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH10_MASK    0x30
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH9_OFFSET    2
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH9_MASK    0xC
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH8_OFFSET    0
-#define    RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH8_MASK    0x3
-
-#define    RTL8367C_REG_DOS_CFG    0x08d4
-#define    RTL8367C_DROP_ICMPFRAGMENT_OFFSET    9
-#define    RTL8367C_DROP_ICMPFRAGMENT_MASK    0x200
-#define    RTL8367C_DROP_TCPFRAGERROR_OFFSET    8
-#define    RTL8367C_DROP_TCPFRAGERROR_MASK    0x100
-#define    RTL8367C_DROP_TCPSHORTHDR_OFFSET    7
-#define    RTL8367C_DROP_TCPSHORTHDR_MASK    0x80
-#define    RTL8367C_DROP_SYN1024_OFFSET    6
-#define    RTL8367C_DROP_SYN1024_MASK    0x40
-#define    RTL8367C_DROP_NULLSCAN_OFFSET    5
-#define    RTL8367C_DROP_NULLSCAN_MASK    0x20
-#define    RTL8367C_DROP_XMASCAN_OFFSET    4
-#define    RTL8367C_DROP_XMASCAN_MASK    0x10
-#define    RTL8367C_DROP_SYNFINSCAN_OFFSET    3
-#define    RTL8367C_DROP_SYNFINSCAN_MASK    0x8
-#define    RTL8367C_DROP_BLATATTACKS_OFFSET    2
-#define    RTL8367C_DROP_BLATATTACKS_MASK    0x4
-#define    RTL8367C_DROP_LANDATTACKS_OFFSET    1
-#define    RTL8367C_DROP_LANDATTACKS_MASK    0x2
-#define    RTL8367C_DROP_DAEQSA_OFFSET    0
-#define    RTL8367C_DROP_DAEQSA_MASK    0x1
-
-#define    RTL8367C_REG_UNKNOWN_L2_MULTICAST_CTRL1    0x08d5
-#define    RTL8367C_PORT10_UNKNOWN_L2_MCAST_OFFSET    4
-#define    RTL8367C_PORT10_UNKNOWN_L2_MCAST_MASK    0x30
-#define    RTL8367C_PORT9_UNKNOWN_L2_MCAST_OFFSET    2
-#define    RTL8367C_PORT9_UNKNOWN_L2_MCAST_MASK    0xC
-#define    RTL8367C_PORT8_UNKNOWN_L2_MCAST_OFFSET    0
-#define    RTL8367C_PORT8_UNKNOWN_L2_MCAST_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4    0x08d6
-#define    RTL8367C_PORT9_VLAN_KEEP_MASK_OFFSET    8
-#define    RTL8367C_PORT9_VLAN_KEEP_MASK_MASK    0xFF00
-#define    RTL8367C_PORT8_VLAN_KEEP_MASK_OFFSET    0
-#define    RTL8367C_PORT8_VLAN_KEEP_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL5    0x08d7
-#define    RTL8367C_VLAN_EGRESS_KEEP_CTRL5_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_KEEP_CTRL5_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL0_EXT    0x08d8
-#define    RTL8367C_PORT1_VLAN_KEEP_MASK_EXT_OFFSET    3
-#define    RTL8367C_PORT1_VLAN_KEEP_MASK_EXT_MASK    0x38
-#define    RTL8367C_PORT0_VLAN_KEEP_MASK_EXT_OFFSET    0
-#define    RTL8367C_PORT0_VLAN_KEEP_MASK_EXT_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL1_EXT    0x08d9
-#define    RTL8367C_PORT3_VLAN_KEEP_MASK_EXT_OFFSET    3
-#define    RTL8367C_PORT3_VLAN_KEEP_MASK_EXT_MASK    0x38
-#define    RTL8367C_PORT2_VLAN_KEEP_MASK_EXT_OFFSET    0
-#define    RTL8367C_PORT2_VLAN_KEEP_MASK_EXT_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL2_EXT    0x08da
-#define    RTL8367C_PORT5_VLAN_KEEP_MASK_EXT_OFFSET    3
-#define    RTL8367C_PORT5_VLAN_KEEP_MASK_EXT_MASK    0x38
-#define    RTL8367C_PORT4_VLAN_KEEP_MASK_EXT_OFFSET    0
-#define    RTL8367C_PORT4_VLAN_KEEP_MASK_EXT_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL3_EXT    0x08db
-#define    RTL8367C_PORT7_VLAN_KEEP_MASK_EXT_OFFSET    3
-#define    RTL8367C_PORT7_VLAN_KEEP_MASK_EXT_MASK    0x38
-#define    RTL8367C_PORT6_VLAN_KEEP_MASK_EXT_OFFSET    0
-#define    RTL8367C_PORT6_VLAN_KEEP_MASK_EXT_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4_EXT    0x08dc
-#define    RTL8367C_PORT9_VLAN_KEEP_MASK_EXT_OFFSET    3
-#define    RTL8367C_PORT9_VLAN_KEEP_MASK_EXT_MASK    0x38
-#define    RTL8367C_PORT8_VLAN_KEEP_MASK_EXT_OFFSET    0
-#define    RTL8367C_PORT8_VLAN_KEEP_MASK_EXT_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL5_EXT    0x08dd
-#define    RTL8367C_VLAN_EGRESS_KEEP_CTRL5_EXT_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_KEEP_CTRL5_EXT_MASK    0x7
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL10    0x08de
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL10_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL10_MASK    0x7FF
-
-#define    RTL8367C_REG_FPGA_VER_CEN    0x08e0
-
-#define    RTL8367C_REG_FPGA_TIME_CEN    0x08e1
-
-#define    RTL8367C_REG_FPGA_DATE_CEN    0x08e2
-
-#define    RTL8367C_REG_QOS_PORT_QUEUE_NUMBER_CTRL0    0x0900
-#define    RTL8367C_PORT3_NUMBER_OFFSET    12
-#define    RTL8367C_PORT3_NUMBER_MASK    0x7000
-#define    RTL8367C_PORT2_NUMBER_OFFSET    8
-#define    RTL8367C_PORT2_NUMBER_MASK    0x700
-#define    RTL8367C_PORT1_NUMBER_OFFSET    4
-#define    RTL8367C_PORT1_NUMBER_MASK    0x70
-#define    RTL8367C_PORT0_NUMBER_OFFSET    0
-#define    RTL8367C_PORT0_NUMBER_MASK    0x7
-
-#define    RTL8367C_REG_QOS_PORT_QUEUE_NUMBER_CTRL1    0x0901
-#define    RTL8367C_PORT7_NUMBER_OFFSET    12
-#define    RTL8367C_PORT7_NUMBER_MASK    0x7000
-#define    RTL8367C_PORT6_NUMBER_OFFSET    8
-#define    RTL8367C_PORT6_NUMBER_MASK    0x700
-#define    RTL8367C_PORT5_NUMBER_OFFSET    4
-#define    RTL8367C_PORT5_NUMBER_MASK    0x70
-#define    RTL8367C_PORT4_NUMBER_OFFSET    0
-#define    RTL8367C_PORT4_NUMBER_MASK    0x7
-
-#define    RTL8367C_REG_QOS_PORT_QUEUE_NUMBER_CTRL2    0x0902
-#define    RTL8367C_PORT10_NUMBER_OFFSET    8
-#define    RTL8367C_PORT10_NUMBER_MASK    0x700
-#define    RTL8367C_PORT9_NUMBER_OFFSET    4
-#define    RTL8367C_PORT9_NUMBER_MASK    0x70
-#define    RTL8367C_PORT8_NUMBER_OFFSET    0
-#define    RTL8367C_PORT8_NUMBER_MASK    0x7
-
-#define    RTL8367C_REG_QOS_1Q_PRIORITY_TO_QID_CTRL0    0x0904
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_1Q_PRIORITY_TO_QID_CTRL1    0x0905
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_1Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_2Q_PRIORITY_TO_QID_CTRL0    0x0906
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_2Q_PRIORITY_TO_QID_CTRL1    0x0907
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_2Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_3Q_PRIORITY_TO_QID_CTRL0    0x0908
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_3Q_PRIORITY_TO_QID_CTRL1    0x0909
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_3Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_4Q_PRIORITY_TO_QID_CTRL0    0x090a
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_4Q_PRIORITY_TO_QID_CTRL1    0x090b
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_4Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_5Q_PRIORITY_TO_QID_CTRL0    0x090c
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_5Q_PRIORITY_TO_QID_CTRL1    0x090d
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_5Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_6Q_PRIORITY_TO_QID_CTRL0    0x090e
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_6Q_PRIORITY_TO_QID_CTRL1    0x090f
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_6Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_7Q_PRIORITY_TO_QID_CTRL0    0x0910
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_7Q_PRIORITY_TO_QID_CTRL1    0x0911
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_7Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_8Q_PRIORITY_TO_QID_CTRL0    0x0912
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY3_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY2_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY1_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL0_PRIORITY0_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_QOS_8Q_PRIORITY_TO_QID_CTRL1    0x0913
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_OFFSET    12
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY7_TO_QID_MASK    0x7000
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_OFFSET    8
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY6_TO_QID_MASK    0x700
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_OFFSET    4
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY5_TO_QID_MASK    0x70
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_OFFSET    0
-#define    RTL8367C_QOS_8Q_PRIORITY_TO_QID_CTRL1_PRIORITY4_TO_QID_MASK    0x7
-
-#define    RTL8367C_REG_HIGHPRI_INDICATOR    0x0915
-#define    RTL8367C_PORT10_INDICATOR_OFFSET    10
-#define    RTL8367C_PORT10_INDICATOR_MASK    0x400
-#define    RTL8367C_PORT9_INDICATOR_OFFSET    9
-#define    RTL8367C_PORT9_INDICATOR_MASK    0x200
-#define    RTL8367C_PORT8_INDICATOR_OFFSET    8
-#define    RTL8367C_PORT8_INDICATOR_MASK    0x100
-#define    RTL8367C_PORT7_INDICATOR_OFFSET    7
-#define    RTL8367C_PORT7_INDICATOR_MASK    0x80
-#define    RTL8367C_PORT6_INDICATOR_OFFSET    6
-#define    RTL8367C_PORT6_INDICATOR_MASK    0x40
-#define    RTL8367C_PORT5_INDICATOR_OFFSET    5
-#define    RTL8367C_PORT5_INDICATOR_MASK    0x20
-#define    RTL8367C_PORT4_INDICATOR_OFFSET    4
-#define    RTL8367C_PORT4_INDICATOR_MASK    0x10
-#define    RTL8367C_PORT3_INDICATOR_OFFSET    3
-#define    RTL8367C_PORT3_INDICATOR_MASK    0x8
-#define    RTL8367C_PORT2_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT2_INDICATOR_MASK    0x4
-#define    RTL8367C_PORT1_INDICATOR_OFFSET    1
-#define    RTL8367C_PORT1_INDICATOR_MASK    0x2
-#define    RTL8367C_PORT0_INDICATOR_OFFSET    0
-#define    RTL8367C_PORT0_INDICATOR_MASK    0x1
-
-#define    RTL8367C_REG_HIGHPRI_CFG    0x0916
-#define    RTL8367C_HIGHPRI_CFG_OFFSET    0
-#define    RTL8367C_HIGHPRI_CFG_MASK    0xFF
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL0    0x0917
-#define    RTL8367C_PORT1_DEBUG_INFO_OFFSET    8
-#define    RTL8367C_PORT1_DEBUG_INFO_MASK    0xFF00
-#define    RTL8367C_PORT0_DEBUG_INFO_OFFSET    0
-#define    RTL8367C_PORT0_DEBUG_INFO_MASK    0xFF
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL1    0x0918
-#define    RTL8367C_PORT3_DEBUG_INFO_OFFSET    8
-#define    RTL8367C_PORT3_DEBUG_INFO_MASK    0xFF00
-#define    RTL8367C_PORT2_DEBUG_INFO_OFFSET    0
-#define    RTL8367C_PORT2_DEBUG_INFO_MASK    0xFF
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL2    0x0919
-#define    RTL8367C_PORT5_DEBUG_INFO_OFFSET    8
-#define    RTL8367C_PORT5_DEBUG_INFO_MASK    0xFF00
-#define    RTL8367C_PORT4_DEBUG_INFO_OFFSET    0
-#define    RTL8367C_PORT4_DEBUG_INFO_MASK    0xFF
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL3    0x091a
-#define    RTL8367C_PORT7_DEBUG_INFO_OFFSET    8
-#define    RTL8367C_PORT7_DEBUG_INFO_MASK    0xFF00
-#define    RTL8367C_PORT6_DEBUG_INFO_OFFSET    0
-#define    RTL8367C_PORT6_DEBUG_INFO_MASK    0xFF
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL4    0x091b
-#define    RTL8367C_PORT9_DEBUG_INFO_OFFSET    8
-#define    RTL8367C_PORT9_DEBUG_INFO_MASK    0xFF00
-#define    RTL8367C_PORT8_DEBUG_INFO_OFFSET    0
-#define    RTL8367C_PORT8_DEBUG_INFO_MASK    0xFF
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL5    0x091c
-#define    RTL8367C_PORT10_DEBUG_INFO_OFFSET    0
-#define    RTL8367C_PORT10_DEBUG_INFO_MASK    0xFF
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL6    0x091d
-#define    RTL8367C_PORT7_DEBUG_INDICATOR_OFFSET    14
-#define    RTL8367C_PORT7_DEBUG_INDICATOR_MASK    0xC000
-#define    RTL8367C_PORT6_DEBUG_INDICATOR_OFFSET    12
-#define    RTL8367C_PORT6_DEBUG_INDICATOR_MASK    0x3000
-#define    RTL8367C_PORT5_DEBUG_INDICATOR_OFFSET    10
-#define    RTL8367C_PORT5_DEBUG_INDICATOR_MASK    0xC00
-#define    RTL8367C_PORT4_DEBUG_INDICATOR_OFFSET    8
-#define    RTL8367C_PORT4_DEBUG_INDICATOR_MASK    0x300
-#define    RTL8367C_PORT3_DEBUG_INDICATOR_OFFSET    6
-#define    RTL8367C_PORT3_DEBUG_INDICATOR_MASK    0xC0
-#define    RTL8367C_PORT2_DEBUG_INDICATOR_OFFSET    4
-#define    RTL8367C_PORT2_DEBUG_INDICATOR_MASK    0x30
-#define    RTL8367C_PORT1_DEBUG_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT1_DEBUG_INDICATOR_MASK    0xC
-#define    RTL8367C_PORT0_DEBUG_INDICATOR_OFFSET    0
-#define    RTL8367C_PORT0_DEBUG_INDICATOR_MASK    0x3
-
-#define    RTL8367C_REG_PORT_DEBUG_INFO_CTRL7    0x091e
-#define    RTL8367C_PORT10_DEBUG_INDICATOR_OFFSET    4
-#define    RTL8367C_PORT10_DEBUG_INDICATOR_MASK    0x30
-#define    RTL8367C_PORT9_DEBUG_INDICATOR_OFFSET    2
-#define    RTL8367C_PORT9_DEBUG_INDICATOR_MASK    0xC
-#define    RTL8367C_PORT8_DEBUG_INDICATOR_OFFSET    0
-#define    RTL8367C_PORT8_DEBUG_INDICATOR_MASK    0x3
-
-#define    RTL8367C_REG_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL0    0x0930
-#define    RTL8367C_PORT1_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT1_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT0_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT0_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL1    0x0931
-#define    RTL8367C_PORT3_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT3_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT2_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT2_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL2    0x0932
-#define    RTL8367C_PORT5_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT5_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT4_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT4_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL3    0x0933
-#define    RTL8367C_PORT7_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT7_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT6_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT6_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL4    0x0934
-#define    RTL8367C_PORT9_QUEUE_MASK_OFFSET    8
-#define    RTL8367C_PORT9_QUEUE_MASK_MASK    0xFF00
-#define    RTL8367C_PORT8_QUEUE_MASK_OFFSET    0
-#define    RTL8367C_PORT8_QUEUE_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL5    0x0935
-#define    RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL5_OFFSET    0
-#define    RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_CTRL5_MASK    0xFF
-
-#define    RTL8367C_REG_FLOWCRTL_EGRESS_PORT_ENABLE    0x0938
-#define    RTL8367C_FLOWCRTL_EGRESS_PORT_ENABLE_OFFSET    0
-#define    RTL8367C_FLOWCRTL_EGRESS_PORT_ENABLE_MASK    0xFF
-
-#define    RTL8367C_REG_EAV_CTRL    0x0939
-#define    RTL8367C_EAV_TRAP_CPU_OFFSET    1
-#define    RTL8367C_EAV_TRAP_CPU_MASK    0x2
-#define    RTL8367C_EAV_TRAP_8051_OFFSET    0
-#define    RTL8367C_EAV_TRAP_8051_MASK    0x1
-
-#define    RTL8367C_REG_UNTAG_DSCP_PRI_CFG    0x093a
-#define    RTL8367C_UNTAG_DSCP_PRI_CFG_OFFSET    0
-#define    RTL8367C_UNTAG_DSCP_PRI_CFG_MASK    0x1
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL0    0x093b
-#define    RTL8367C_PORT1_VLAN_KEEP_MASK_OFFSET    8
-#define    RTL8367C_PORT1_VLAN_KEEP_MASK_MASK    0xFF00
-#define    RTL8367C_PORT0_VLAN_KEEP_MASK_OFFSET    0
-#define    RTL8367C_PORT0_VLAN_KEEP_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL1    0x093c
-#define    RTL8367C_PORT3_VLAN_KEEP_MASK_OFFSET    8
-#define    RTL8367C_PORT3_VLAN_KEEP_MASK_MASK    0xFF00
-#define    RTL8367C_PORT2_VLAN_KEEP_MASK_OFFSET    0
-#define    RTL8367C_PORT2_VLAN_KEEP_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL2    0x093d
-#define    RTL8367C_PORT5_VLAN_KEEP_MASK_OFFSET    8
-#define    RTL8367C_PORT5_VLAN_KEEP_MASK_MASK    0xFF00
-#define    RTL8367C_PORT4_VLAN_KEEP_MASK_OFFSET    0
-#define    RTL8367C_PORT4_VLAN_KEEP_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL3    0x093e
-#define    RTL8367C_PORT7_VLAN_KEEP_MASK_OFFSET    8
-#define    RTL8367C_PORT7_VLAN_KEEP_MASK_MASK    0xFF00
-#define    RTL8367C_PORT6_VLAN_KEEP_MASK_OFFSET    0
-#define    RTL8367C_PORT6_VLAN_KEEP_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_VLAN_TRANSPARENT_EN_CFG    0x093f
-#define    RTL8367C_VLAN_TRANSPARENT_EN_CFG_OFFSET    0
-#define    RTL8367C_VLAN_TRANSPARENT_EN_CFG_MASK    0x1
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY0_H    0x0940
-#define    RTL8367C_IPMC_GROUP_ENTRY0_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY0_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY0_L    0x0941
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY1_H    0x0942
-#define    RTL8367C_IPMC_GROUP_ENTRY1_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY1_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY1_L    0x0943
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY2_H    0x0944
-#define    RTL8367C_IPMC_GROUP_ENTRY2_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY2_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY2_L    0x0945
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY3_H    0x0946
-#define    RTL8367C_IPMC_GROUP_ENTRY3_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY3_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY3_L    0x0947
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY4_H    0x0948
-#define    RTL8367C_IPMC_GROUP_ENTRY4_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY4_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY4_L    0x0949
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY5_H    0x094a
-#define    RTL8367C_IPMC_GROUP_ENTRY5_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY5_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY5_L    0x094b
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY6_H    0x094c
-#define    RTL8367C_IPMC_GROUP_ENTRY6_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY6_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY6_L    0x094d
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY7_H    0x094e
-#define    RTL8367C_IPMC_GROUP_ENTRY7_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY7_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY7_L    0x094f
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY8_H    0x0950
-#define    RTL8367C_IPMC_GROUP_ENTRY8_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY8_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY8_L    0x0951
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY9_H    0x0952
-#define    RTL8367C_IPMC_GROUP_ENTRY9_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY9_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY9_L    0x0953
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY10_H    0x0954
-#define    RTL8367C_IPMC_GROUP_ENTRY10_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY10_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY10_L    0x0955
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY11_H    0x0956
-#define    RTL8367C_IPMC_GROUP_ENTRY11_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY11_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY11_L    0x0957
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY12_H    0x0958
-#define    RTL8367C_IPMC_GROUP_ENTRY12_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY12_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY12_L    0x0959
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY13_H    0x095a
-#define    RTL8367C_IPMC_GROUP_ENTRY13_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY13_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY13_L    0x095b
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY14_H    0x095c
-#define    RTL8367C_IPMC_GROUP_ENTRY14_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY14_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY14_L    0x095d
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY15_H    0x095e
-#define    RTL8367C_IPMC_GROUP_ENTRY15_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY15_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY15_L    0x095f
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY16_H    0x0960
-#define    RTL8367C_IPMC_GROUP_ENTRY16_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY16_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY16_L    0x0961
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY17_H    0x0962
-#define    RTL8367C_IPMC_GROUP_ENTRY17_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY17_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY17_L    0x0963
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY18_H    0x0964
-#define    RTL8367C_IPMC_GROUP_ENTRY18_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY18_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY18_L    0x0965
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY19_H    0x0966
-#define    RTL8367C_IPMC_GROUP_ENTRY19_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY19_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY19_L    0x0967
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY20_H    0x0968
-#define    RTL8367C_IPMC_GROUP_ENTRY20_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY20_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY20_L    0x0969
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY21_H    0x096a
-#define    RTL8367C_IPMC_GROUP_ENTRY21_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY21_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY21_L    0x096b
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY22_H    0x096c
-#define    RTL8367C_IPMC_GROUP_ENTRY22_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY22_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY22_L    0x096d
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY23_H    0x096e
-#define    RTL8367C_IPMC_GROUP_ENTRY23_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY23_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY23_L    0x096f
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY24_H    0x0970
-#define    RTL8367C_IPMC_GROUP_ENTRY24_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY24_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY24_L    0x0971
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY25_H    0x0972
-#define    RTL8367C_IPMC_GROUP_ENTRY25_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY25_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY25_L    0x0973
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY26_H    0x0974
-#define    RTL8367C_IPMC_GROUP_ENTRY26_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY26_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY26_L    0x0975
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY27_H    0x0976
-#define    RTL8367C_IPMC_GROUP_ENTRY27_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY27_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY27_L    0x0977
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY28_H    0x0978
-#define    RTL8367C_IPMC_GROUP_ENTRY28_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY28_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY28_L    0x0979
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY29_H    0x097a
-#define    RTL8367C_IPMC_GROUP_ENTRY29_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY29_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY29_L    0x097b
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY30_H    0x097c
-#define    RTL8367C_IPMC_GROUP_ENTRY30_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY30_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY30_L    0x097d
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY31_H    0x097e
-#define    RTL8367C_IPMC_GROUP_ENTRY31_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY31_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY31_L    0x097f
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY32_H    0x0980
-#define    RTL8367C_IPMC_GROUP_ENTRY32_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY32_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY32_L    0x0981
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY33_H    0x0982
-#define    RTL8367C_IPMC_GROUP_ENTRY33_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY33_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY33_L    0x0983
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY34_H    0x0984
-#define    RTL8367C_IPMC_GROUP_ENTRY34_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY34_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY34_L    0x0985
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY35_H    0x0986
-#define    RTL8367C_IPMC_GROUP_ENTRY35_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY35_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY35_L    0x0987
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY36_H    0x0988
-#define    RTL8367C_IPMC_GROUP_ENTRY36_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY36_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY36_L    0x0989
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY37_H    0x098a
-#define    RTL8367C_IPMC_GROUP_ENTRY37_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY37_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY37_L    0x098b
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY38_H    0x098c
-#define    RTL8367C_IPMC_GROUP_ENTRY38_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY38_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY38_L    0x098d
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY39_H    0x098e
-#define    RTL8367C_IPMC_GROUP_ENTRY39_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY39_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY39_L    0x098f
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY40_H    0x0990
-#define    RTL8367C_IPMC_GROUP_ENTRY40_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY40_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY40_L    0x0991
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY41_H    0x0992
-#define    RTL8367C_IPMC_GROUP_ENTRY41_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY41_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY41_L    0x0993
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY42_H    0x0994
-#define    RTL8367C_IPMC_GROUP_ENTRY42_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY42_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY42_L    0x0995
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY43_H    0x0996
-#define    RTL8367C_IPMC_GROUP_ENTRY43_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY43_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY43_L    0x0997
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY44_H    0x0998
-#define    RTL8367C_IPMC_GROUP_ENTRY44_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY44_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY44_L    0x0999
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY45_H    0x099a
-#define    RTL8367C_IPMC_GROUP_ENTRY45_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY45_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY45_L    0x099b
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY46_H    0x099c
-#define    RTL8367C_IPMC_GROUP_ENTRY46_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY46_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY46_L    0x099d
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY47_H    0x099e
-#define    RTL8367C_IPMC_GROUP_ENTRY47_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY47_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY47_L    0x099f
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY48_H    0x09a0
-#define    RTL8367C_IPMC_GROUP_ENTRY48_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY48_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY48_L    0x09a1
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY49_H    0x09a2
-#define    RTL8367C_IPMC_GROUP_ENTRY49_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY49_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY49_L    0x09a3
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY50_H    0x09a4
-#define    RTL8367C_IPMC_GROUP_ENTRY50_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY50_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY50_L    0x09a5
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY51_H    0x09a6
-#define    RTL8367C_IPMC_GROUP_ENTRY51_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY51_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY51_L    0x09a7
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY52_H    0x09a8
-#define    RTL8367C_IPMC_GROUP_ENTRY52_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY52_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY52_L    0x09a9
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY53_H    0x09aa
-#define    RTL8367C_IPMC_GROUP_ENTRY53_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY53_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY53_L    0x09ab
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY54_H    0x09ac
-#define    RTL8367C_IPMC_GROUP_ENTRY54_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY54_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY54_L    0x09ad
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY55_H    0x09ae
-#define    RTL8367C_IPMC_GROUP_ENTRY55_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY55_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY55_L    0x09af
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY56_H    0x09b0
-#define    RTL8367C_IPMC_GROUP_ENTRY56_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY56_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY56_L    0x09b1
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY57_H    0x09b2
-#define    RTL8367C_IPMC_GROUP_ENTRY57_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY57_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY57_L    0x09b3
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY58_H    0x09b4
-#define    RTL8367C_IPMC_GROUP_ENTRY58_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY58_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY58_L    0x09b5
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY59_H    0x09b6
-#define    RTL8367C_IPMC_GROUP_ENTRY59_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY59_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY59_L    0x09b7
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY60_H    0x09b8
-#define    RTL8367C_IPMC_GROUP_ENTRY60_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY60_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY60_L    0x09b9
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY61_H    0x09ba
-#define    RTL8367C_IPMC_GROUP_ENTRY61_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY61_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY61_L    0x09bb
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY62_H    0x09bc
-#define    RTL8367C_IPMC_GROUP_ENTRY62_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY62_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY62_L    0x09bd
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY63_H    0x09be
-#define    RTL8367C_IPMC_GROUP_ENTRY63_H_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_ENTRY63_H_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_ENTRY63_L    0x09bf
-
-#define    RTL8367C_REG_UNKNOWN_UNICAST_DA_PORT_BEHAVE    0x09C0
-#define    RTL8367C_Port7_ACTION_OFFSET    14
-#define    RTL8367C_Port7_ACTION_MASK    0xC000
-#define    RTL8367C_Port6_ACTION_OFFSET    12
-#define    RTL8367C_Port6_ACTION_MASK    0x3000
-#define    RTL8367C_Port5_ACTION_OFFSET    10
-#define    RTL8367C_Port5_ACTION_MASK    0xC00
-#define    RTL8367C_Port4_ACTION_OFFSET    8
-#define    RTL8367C_Port4_ACTION_MASK    0x300
-#define    RTL8367C_Port3_ACTION_OFFSET    6
-#define    RTL8367C_Port3_ACTION_MASK    0xC0
-#define    RTL8367C_Port2_ACTION_OFFSET    4
-#define    RTL8367C_Port2_ACTION_MASK    0x30
-#define    RTL8367C_Port1_ACTION_OFFSET    2
-#define    RTL8367C_Port1_ACTION_MASK    0xC
-#define    RTL8367C_Port0_ACTION_OFFSET    0
-#define    RTL8367C_Port0_ACTION_MASK    0x3
-
-#define    RTL8367C_REG_MIRROR_CTRL3    0x09C1
-#define    RTL8367C_MIRROR_ACL_OVERRIDE_EN_OFFSET    2
-#define    RTL8367C_MIRROR_ACL_OVERRIDE_EN_MASK    0x4
-#define    RTL8367C_MIRROR_TX_OVERRIDE_EN_OFFSET    1
-#define    RTL8367C_MIRROR_TX_OVERRIDE_EN_MASK    0x2
-#define    RTL8367C_MIRROR_RX_OVERRIDE_EN_OFFSET    0
-#define    RTL8367C_MIRROR_RX_OVERRIDE_EN_MASK    0x1
-
-#define    RTL8367C_REG_DPM_DUMMY02    0x09C2
-
-#define    RTL8367C_REG_DPM_DUMMY03    0x09C3
-
-#define    RTL8367C_REG_DPM_DUMMY04    0x09C4
-
-#define    RTL8367C_REG_DPM_DUMMY05    0x09C5
-
-#define    RTL8367C_REG_DPM_DUMMY06    0x09C6
-
-#define    RTL8367C_REG_DPM_DUMMY07    0x09C7
-
-#define    RTL8367C_REG_DPM_DUMMY08    0x09C8
-
-#define    RTL8367C_REG_DPM_DUMMY09    0x09C9
-
-#define    RTL8367C_REG_DPM_DUMMY10    0x09CA
-
-#define    RTL8367C_REG_DPM_DUMMY11    0x09CB
-
-#define    RTL8367C_REG_DPM_DUMMY12    0x09CC
-
-#define    RTL8367C_REG_DPM_DUMMY13    0x09CD
-
-#define    RTL8367C_REG_DPM_DUMMY14    0x09CE
-
-#define    RTL8367C_REG_DPM_DUMMY15    0x09CF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL0    0x09D0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL0_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL0_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL1    0x09D1
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL1_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL1_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL2    0x09D2
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL2_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL2_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL3    0x09D3
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL3_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL3_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL4    0x09D4
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL4_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL4_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL5    0x09D5
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL5_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL5_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL6    0x09D6
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL6_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL6_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL7    0x09D7
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL7_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL7_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL8    0x09D8
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL8_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL8_MASK    0x7FF
-
-#define    RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL9    0x09D9
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL9_OFFSET    0
-#define    RTL8367C_VLAN_EGRESS_TRANS_CTRL9_MASK    0x7FF
-
-#define    RTL8367C_REG_MIRROR_CTRL2    0x09DA
-#define    RTL8367C_MIRROR_REALKEEP_EN_OFFSET    4
-#define    RTL8367C_MIRROR_REALKEEP_EN_MASK    0x10
-#define    RTL8367C_MIRROR_RX_ISOLATION_LEAKY_OFFSET    3
-#define    RTL8367C_MIRROR_RX_ISOLATION_LEAKY_MASK    0x8
-#define    RTL8367C_MIRROR_TX_ISOLATION_LEAKY_OFFSET    2
-#define    RTL8367C_MIRROR_TX_ISOLATION_LEAKY_MASK    0x4
-#define    RTL8367C_MIRROR_RX_VLAN_LEAKY_OFFSET    1
-#define    RTL8367C_MIRROR_RX_VLAN_LEAKY_MASK    0x2
-#define    RTL8367C_MIRROR_TX_VLAN_LEAKY_OFFSET    0
-#define    RTL8367C_MIRROR_TX_VLAN_LEAKY_MASK    0x1
-
-#define    RTL8367C_REG_OUTPUT_DROP_CFG    0x09DB
-#define    RTL8367C_ENABLE_PMASK_EXT_OFFSET    13
-#define    RTL8367C_ENABLE_PMASK_EXT_MASK    0xE000
-#define    RTL8367C_ENABLE_BC_OFFSET    12
-#define    RTL8367C_ENABLE_BC_MASK    0x1000
-#define    RTL8367C_ENABLE_MC_OFFSET    11
-#define    RTL8367C_ENABLE_MC_MASK    0x800
-#define    RTL8367C_ENABLE_UC_OFFSET    10
-#define    RTL8367C_ENABLE_UC_MASK    0x400
-#define    RTL8367C_ENABLE_PMASK_OFFSET    0
-#define    RTL8367C_ENABLE_PMASK_MASK    0xFF
-
-#define    RTL8367C_REG_UNKNOWN_UNICAST_DA_PORT_BEHAVE_EXT    0x09DC
-#define    RTL8367C_PORT10_ACTION_OFFSET    4
-#define    RTL8367C_PORT10_ACTION_MASK    0x30
-#define    RTL8367C_PORT9_ACTION_OFFSET    2
-#define    RTL8367C_PORT9_ACTION_MASK    0xC
-#define    RTL8367C_PORT8_ACTION_OFFSET    0
-#define    RTL8367C_PORT8_ACTION_MASK    0x3
-
-#define    RTL8367C_REG_RMK_CFG_SEL_CTRL    0x09DF
-#define    RTL8367C_RMK_1Q_CFG_SEL_OFFSET    2
-#define    RTL8367C_RMK_1Q_CFG_SEL_MASK    0x4
-#define    RTL8367C_RMK_DSCP_CFG_SEL_OFFSET    0
-#define    RTL8367C_RMK_DSCP_CFG_SEL_MASK    0x3
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL0    0x09E0
-#define    RTL8367C_DSCP1_DSCP_OFFSET    8
-#define    RTL8367C_DSCP1_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP0_DSCP_OFFSET    0
-#define    RTL8367C_DSCP0_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL1    0x09E1
-#define    RTL8367C_DSCP3_DSCP_OFFSET    8
-#define    RTL8367C_DSCP3_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP2_DSCP_OFFSET    0
-#define    RTL8367C_DSCP2_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL2    0x09E2
-#define    RTL8367C_DSCP5_DSCP_OFFSET    8
-#define    RTL8367C_DSCP5_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP4_DSCP_OFFSET    0
-#define    RTL8367C_DSCP4_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL3    0x09E3
-#define    RTL8367C_DSCP7_DSCP_OFFSET    8
-#define    RTL8367C_DSCP7_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP6_DSCP_OFFSET    0
-#define    RTL8367C_DSCP6_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL4    0x09E4
-#define    RTL8367C_DSCP9_DSCP_OFFSET    8
-#define    RTL8367C_DSCP9_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP8_DSCP_OFFSET    0
-#define    RTL8367C_DSCP8_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL5    0x09E5
-#define    RTL8367C_DSCP11_DSCP_OFFSET    8
-#define    RTL8367C_DSCP11_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP10_DSCP_OFFSET    0
-#define    RTL8367C_DSCP10_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL6    0x09E6
-#define    RTL8367C_DSCP13_DSCP_OFFSET    8
-#define    RTL8367C_DSCP13_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP12_DSCP_OFFSET    0
-#define    RTL8367C_DSCP12_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL7    0x09E7
-#define    RTL8367C_DSCP15_DSCP_OFFSET    8
-#define    RTL8367C_DSCP15_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP14_DSCP_OFFSET    0
-#define    RTL8367C_DSCP14_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL8    0x09E8
-#define    RTL8367C_DSCP17_DSCP_OFFSET    8
-#define    RTL8367C_DSCP17_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP16_DSCP_OFFSET    0
-#define    RTL8367C_DSCP16_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL9    0x09E9
-#define    RTL8367C_DSCP19_DSCP_OFFSET    8
-#define    RTL8367C_DSCP19_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP18_DSCP_OFFSET    0
-#define    RTL8367C_DSCP18_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL10    0x09EA
-#define    RTL8367C_DSCP21_DSCP_OFFSET    8
-#define    RTL8367C_DSCP21_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP20_DSCP_OFFSET    0
-#define    RTL8367C_DSCP20_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL11    0x09EB
-#define    RTL8367C_DSCP23_DSCP_OFFSET    8
-#define    RTL8367C_DSCP23_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP22_DSCP_OFFSET    0
-#define    RTL8367C_DSCP22_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL12    0x09EC
-#define    RTL8367C_DSCP25_DSCP_OFFSET    8
-#define    RTL8367C_DSCP25_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP24_DSCP_OFFSET    0
-#define    RTL8367C_DSCP24_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL13    0x09ED
-#define    RTL8367C_DSCP27_DSCP_OFFSET    8
-#define    RTL8367C_DSCP27_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP26_DSCP_OFFSET    0
-#define    RTL8367C_DSCP26_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL14    0x09EE
-#define    RTL8367C_DSCP29_DSCP_OFFSET    8
-#define    RTL8367C_DSCP29_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP28_DSCP_OFFSET    0
-#define    RTL8367C_DSCP28_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL15    0x09EF
-#define    RTL8367C_DSCP31_DSCP_OFFSET    8
-#define    RTL8367C_DSCP31_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP30_DSCP_OFFSET    0
-#define    RTL8367C_DSCP30_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL16    0x09F0
-#define    RTL8367C_DSCP33_DSCP_OFFSET    8
-#define    RTL8367C_DSCP33_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP32_DSCP_OFFSET    0
-#define    RTL8367C_DSCP32_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL17    0x09F1
-#define    RTL8367C_DSCP35_DSCP_OFFSET    8
-#define    RTL8367C_DSCP35_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP34_DSCP_OFFSET    0
-#define    RTL8367C_DSCP34_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL18    0x09F2
-#define    RTL8367C_DSCP37_DSCP_OFFSET    8
-#define    RTL8367C_DSCP37_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP36_DSCP_OFFSET    0
-#define    RTL8367C_DSCP36_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL19    0x09F3
-#define    RTL8367C_DSCP39_DSCP_OFFSET    8
-#define    RTL8367C_DSCP39_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP38_DSCP_OFFSET    0
-#define    RTL8367C_DSCP38_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL20    0x09F4
-#define    RTL8367C_DSCP41_DSCP_OFFSET    8
-#define    RTL8367C_DSCP41_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP40_DSCP_OFFSET    0
-#define    RTL8367C_DSCP40_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL21    0x09F5
-#define    RTL8367C_DSCP43_DSCP_OFFSET    8
-#define    RTL8367C_DSCP43_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP42_DSCP_OFFSET    0
-#define    RTL8367C_DSCP42_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL22    0x09F6
-#define    RTL8367C_DSCP45_DSCP_OFFSET    8
-#define    RTL8367C_DSCP45_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP44_DSCP_OFFSET    0
-#define    RTL8367C_DSCP44_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL23    0x09F7
-#define    RTL8367C_DSCP47_DSCP_OFFSET    8
-#define    RTL8367C_DSCP47_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP46_DSCP_OFFSET    0
-#define    RTL8367C_DSCP46_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL24    0x09F8
-#define    RTL8367C_DSCP49_DSCP_OFFSET    8
-#define    RTL8367C_DSCP49_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP48_DSCP_OFFSET    0
-#define    RTL8367C_DSCP48_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL25    0x09F9
-#define    RTL8367C_DSCP51_DSCP_OFFSET    8
-#define    RTL8367C_DSCP51_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP50_DSCP_OFFSET    0
-#define    RTL8367C_DSCP50_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL26    0x09FA
-#define    RTL8367C_DSCP53_DSCP_OFFSET    8
-#define    RTL8367C_DSCP53_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP52_DSCP_OFFSET    0
-#define    RTL8367C_DSCP52_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL27    0x09FB
-#define    RTL8367C_DSCP55_DSCP_OFFSET    8
-#define    RTL8367C_DSCP55_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP54_DSCP_OFFSET    0
-#define    RTL8367C_DSCP54_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL28    0x09FC
-#define    RTL8367C_DSCP57_DSCP_OFFSET    8
-#define    RTL8367C_DSCP57_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP56_DSCP_OFFSET    0
-#define    RTL8367C_DSCP56_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL29    0x09FD
-#define    RTL8367C_DSCP59_DSCP_OFFSET    8
-#define    RTL8367C_DSCP59_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP58_DSCP_OFFSET    0
-#define    RTL8367C_DSCP58_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL30    0x09FE
-#define    RTL8367C_DSCP61_DSCP_OFFSET    8
-#define    RTL8367C_DSCP61_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP60_DSCP_OFFSET    0
-#define    RTL8367C_DSCP60_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_DSCP_CTRL31    0x09FF
-#define    RTL8367C_DSCP63_DSCP_OFFSET    8
-#define    RTL8367C_DSCP63_DSCP_MASK    0x3F00
-#define    RTL8367C_DSCP62_DSCP_OFFSET    0
-#define    RTL8367C_DSCP62_DSCP_MASK    0x3F
-
-/* (16'h0a00)l2_reg */
-
-#define    RTL8367C_REG_VLAN_MSTI0_CTRL0    0x0a00
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI0_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI0_CTRL1    0x0a01
-#define    RTL8367C_VLAN_MSTI0_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI0_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI0_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI0_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI0_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI0_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI1_CTRL0    0x0a02
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI1_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI1_CTRL1    0x0a03
-#define    RTL8367C_VLAN_MSTI1_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI1_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI1_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI1_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI1_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI1_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI2_CTRL0    0x0a04
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI2_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI2_CTRL1    0x0a05
-#define    RTL8367C_VLAN_MSTI2_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI2_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI2_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI2_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI2_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI2_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI3_CTRL0    0x0a06
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI3_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI3_CTRL1    0x0a07
-#define    RTL8367C_VLAN_MSTI3_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI3_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI3_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI3_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI3_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI3_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI4_CTRL0    0x0a08
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI4_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI4_CTRL1    0x0a09
-#define    RTL8367C_VLAN_MSTI4_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI4_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI4_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI4_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI4_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI4_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI5_CTRL0    0x0a0a
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI5_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI5_CTRL1    0x0a0b
-#define    RTL8367C_VLAN_MSTI5_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI5_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI5_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI5_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI5_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI5_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI6_CTRL0    0x0a0c
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI6_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI6_CTRL1    0x0a0d
-#define    RTL8367C_VLAN_MSTI6_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI6_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI6_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI6_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI6_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI6_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI7_CTRL0    0x0a0e
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI7_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI7_CTRL1    0x0a0f
-#define    RTL8367C_VLAN_MSTI7_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI7_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI7_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI7_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI7_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI7_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI8_CTRL0    0x0a10
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI8_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI8_CTRL1    0x0a11
-#define    RTL8367C_VLAN_MSTI8_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI8_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI8_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI8_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI8_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI8_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI9_CTRL0    0x0a12
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI9_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI9_CTRL1    0x0a13
-#define    RTL8367C_VLAN_MSTI9_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI9_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI9_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI9_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI9_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI9_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI10_CTRL0    0x0a14
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI10_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI10_CTRL1    0x0a15
-#define    RTL8367C_VLAN_MSTI10_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI10_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI10_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI10_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI10_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI10_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI11_CTRL0    0x0a16
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI11_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI11_CTRL1    0x0a17
-#define    RTL8367C_VLAN_MSTI11_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI11_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI11_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI11_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI11_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI11_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI12_CTRL0    0x0a18
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI12_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI12_CTRL1    0x0a19
-#define    RTL8367C_VLAN_MSTI12_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI12_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI12_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI12_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI12_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI12_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI13_CTRL0    0x0a1a
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI13_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI13_CTRL1    0x0a1b
-#define    RTL8367C_VLAN_MSTI13_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI13_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI13_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI13_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI13_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI13_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI14_CTRL0    0x0a1c
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI14_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI14_CTRL1    0x0a1d
-#define    RTL8367C_VLAN_MSTI14_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI14_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI14_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI14_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI14_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI14_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI15_CTRL0    0x0a1e
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT7_STATE_OFFSET    14
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT7_STATE_MASK    0xC000
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT6_STATE_OFFSET    12
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT6_STATE_MASK    0x3000
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT5_STATE_OFFSET    10
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT5_STATE_MASK    0xC00
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT4_STATE_OFFSET    8
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT4_STATE_MASK    0x300
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT3_STATE_OFFSET    6
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT3_STATE_MASK    0xC0
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT2_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT2_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT1_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT1_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT0_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI15_CTRL0_PORT0_STATE_MASK    0x3
-
-#define    RTL8367C_REG_VLAN_MSTI15_CTRL1    0x0a1f
-#define    RTL8367C_VLAN_MSTI15_CTRL1_PORT10_STATE_OFFSET    4
-#define    RTL8367C_VLAN_MSTI15_CTRL1_PORT10_STATE_MASK    0x30
-#define    RTL8367C_VLAN_MSTI15_CTRL1_PORT9_STATE_OFFSET    2
-#define    RTL8367C_VLAN_MSTI15_CTRL1_PORT9_STATE_MASK    0xC
-#define    RTL8367C_VLAN_MSTI15_CTRL1_PORT8_STATE_OFFSET    0
-#define    RTL8367C_VLAN_MSTI15_CTRL1_PORT8_STATE_MASK    0x3
-
-#define    RTL8367C_REG_LUT_PORT0_LEARN_LIMITNO    0x0a20
-#define    RTL8367C_LUT_PORT0_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT0_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT1_LEARN_LIMITNO    0x0a21
-#define    RTL8367C_LUT_PORT1_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT1_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT2_LEARN_LIMITNO    0x0a22
-#define    RTL8367C_LUT_PORT2_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT2_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT3_LEARN_LIMITNO    0x0a23
-#define    RTL8367C_LUT_PORT3_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT3_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT4_LEARN_LIMITNO    0x0a24
-#define    RTL8367C_LUT_PORT4_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT4_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT5_LEARN_LIMITNO    0x0a25
-#define    RTL8367C_LUT_PORT5_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT5_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT6_LEARN_LIMITNO    0x0a26
-#define    RTL8367C_LUT_PORT6_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT6_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT7_LEARN_LIMITNO    0x0a27
-#define    RTL8367C_LUT_PORT7_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT7_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_SYS_LEARN_LIMITNO    0x0a28
-#define    RTL8367C_LUT_SYS_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_SYS_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_LRN_SYS_LMT_CTRL    0x0a29
-#define    RTL8367C_LUT_SYSTEM_LEARN_PMASK1_OFFSET    12
-#define    RTL8367C_LUT_SYSTEM_LEARN_PMASK1_MASK    0x7000
-#define    RTL8367C_LUT_SYSTEM_LEARN_OVER_ACT_OFFSET    10
-#define    RTL8367C_LUT_SYSTEM_LEARN_OVER_ACT_MASK    0xC00
-#define    RTL8367C_LUT_SYSTEM_LEARN_PMASK_OFFSET    0
-#define    RTL8367C_LUT_SYSTEM_LEARN_PMASK_MASK    0xFF
-
-#define    RTL8367C_REG_LUT_PORT8_LEARN_LIMITNO    0x0a2a
-#define    RTL8367C_LUT_PORT8_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT8_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT9_LEARN_LIMITNO    0x0a2b
-#define    RTL8367C_LUT_PORT9_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT9_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_PORT10_LEARN_LIMITNO    0x0a2c
-#define    RTL8367C_LUT_PORT10_LEARN_LIMITNO_OFFSET    0
-#define    RTL8367C_LUT_PORT10_LEARN_LIMITNO_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_CFG    0x0a30
-#define    RTL8367C_AGE_SPEED_OFFSET    8
-#define    RTL8367C_AGE_SPEED_MASK    0x300
-#define    RTL8367C_BCAM_DISABLE_OFFSET    6
-#define    RTL8367C_BCAM_DISABLE_MASK    0x40
-#define    RTL8367C_LINKDOWN_AGEOUT_OFFSET    5
-#define    RTL8367C_LINKDOWN_AGEOUT_MASK    0x20
-#define    RTL8367C_LUT_IPMC_HASH_OFFSET    4
-#define    RTL8367C_LUT_IPMC_HASH_MASK    0x10
-#define    RTL8367C_LUT_IPMC_LOOKUP_OP_OFFSET    3
-#define    RTL8367C_LUT_IPMC_LOOKUP_OP_MASK    0x8
-#define    RTL8367C_AGE_TIMER_OFFSET    0
-#define    RTL8367C_AGE_TIMER_MASK    0x7
-
-#define    RTL8367C_REG_LUT_AGEOUT_CTRL    0x0a31
-#define    RTL8367C_LUT_AGEOUT_CTRL_OFFSET    0
-#define    RTL8367C_LUT_AGEOUT_CTRL_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_EFID_CTRL0    0x0a32
-#define    RTL8367C_PORT3_EFID_OFFSET    12
-#define    RTL8367C_PORT3_EFID_MASK    0x7000
-#define    RTL8367C_PORT2_EFID_OFFSET    8
-#define    RTL8367C_PORT2_EFID_MASK    0x700
-#define    RTL8367C_PORT1_EFID_OFFSET    4
-#define    RTL8367C_PORT1_EFID_MASK    0x70
-#define    RTL8367C_PORT0_EFID_OFFSET    0
-#define    RTL8367C_PORT0_EFID_MASK    0x7
-
-#define    RTL8367C_REG_PORT_EFID_CTRL1    0x0a33
-#define    RTL8367C_PORT7_EFID_OFFSET    12
-#define    RTL8367C_PORT7_EFID_MASK    0x7000
-#define    RTL8367C_PORT6_EFID_OFFSET    8
-#define    RTL8367C_PORT6_EFID_MASK    0x700
-#define    RTL8367C_PORT5_EFID_OFFSET    4
-#define    RTL8367C_PORT5_EFID_MASK    0x70
-#define    RTL8367C_PORT4_EFID_OFFSET    0
-#define    RTL8367C_PORT4_EFID_MASK    0x7
-
-#define    RTL8367C_REG_PORT_EFID_CTRL2    0x0a34
-#define    RTL8367C_PORT10_EFID_OFFSET    8
-#define    RTL8367C_PORT10_EFID_MASK    0x700
-#define    RTL8367C_PORT9_EFID_OFFSET    4
-#define    RTL8367C_PORT9_EFID_MASK    0x70
-#define    RTL8367C_PORT8_EFID_OFFSET    0
-#define    RTL8367C_PORT8_EFID_MASK    0x7
-
-#define    RTL8367C_REG_FORCE_FLUSH1    0x0a35
-#define    RTL8367C_BUSY_STATUS1_OFFSET    3
-#define    RTL8367C_BUSY_STATUS1_MASK    0x38
-#define    RTL8367C_PORTMASK1_OFFSET    0
-#define    RTL8367C_PORTMASK1_MASK    0x7
-
-#define    RTL8367C_REG_FORCE_FLUSH    0x0a36
-#define    RTL8367C_BUSY_STATUS_OFFSET    8
-#define    RTL8367C_BUSY_STATUS_MASK    0xFF00
-#define    RTL8367C_FORCE_FLUSH_PORTMASK_OFFSET    0
-#define    RTL8367C_FORCE_FLUSH_PORTMASK_MASK    0xFF
-
-#define    RTL8367C_REG_L2_FLUSH_CTRL1    0x0a37
-#define    RTL8367C_LUT_FLUSH_FID_OFFSET    12
-#define    RTL8367C_LUT_FLUSH_FID_MASK    0xF000
-#define    RTL8367C_LUT_FLUSH_VID_OFFSET    0
-#define    RTL8367C_LUT_FLUSH_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_L2_FLUSH_CTRL2    0x0a38
-#define    RTL8367C_LUT_FLUSH_TYPE_OFFSET    2
-#define    RTL8367C_LUT_FLUSH_TYPE_MASK    0x4
-#define    RTL8367C_LUT_FLUSH_MODE_OFFSET    0
-#define    RTL8367C_LUT_FLUSH_MODE_MASK    0x3
-
-#define    RTL8367C_REG_L2_FLUSH_CTRL3    0x0a39
-#define    RTL8367C_L2_FLUSH_CTRL3_OFFSET    0
-#define    RTL8367C_L2_FLUSH_CTRL3_MASK    0x1
-
-#define    RTL8367C_REG_LUT_CFG2    0x0a3a
-#define    RTL8367C_LUT_IPMC_FWD_RPORT_OFFSET    1
-#define    RTL8367C_LUT_IPMC_FWD_RPORT_MASK    0x2
-#define    RTL8367C_LUT_IPMC_VID_HASH_OFFSET    0
-#define    RTL8367C_LUT_IPMC_VID_HASH_MASK    0x1
-
-#define    RTL8367C_REG_FLUSH_STATUS    0x0a3f
-#define    RTL8367C_FLUSH_STATUS_OFFSET    0
-#define    RTL8367C_FLUSH_STATUS_MASK    0x1
-
-#define    RTL8367C_REG_STORM_BCAST    0x0a40
-#define    RTL8367C_STORM_BCAST_OFFSET    0
-#define    RTL8367C_STORM_BCAST_MASK    0x7FF
-
-#define    RTL8367C_REG_STORM_MCAST    0x0a41
-#define    RTL8367C_STORM_MCAST_OFFSET    0
-#define    RTL8367C_STORM_MCAST_MASK    0x7FF
-
-#define    RTL8367C_REG_STORM_UNKOWN_UCAST    0x0a42
-#define    RTL8367C_STORM_UNKOWN_UCAST_OFFSET    0
-#define    RTL8367C_STORM_UNKOWN_UCAST_MASK    0x7FF
-
-#define    RTL8367C_REG_STORM_UNKOWN_MCAST    0x0a43
-#define    RTL8367C_STORM_UNKOWN_MCAST_OFFSET    0
-#define    RTL8367C_STORM_UNKOWN_MCAST_MASK    0x7FF
-
-#define    RTL8367C_REG_STORM_BCAST_METER_CTRL0    0x0a44
-#define    RTL8367C_STORM_BCAST_METER_CTRL0_PORT1_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_BCAST_METER_CTRL0_PORT1_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_BCAST_METER_CTRL0_PORT0_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_BCAST_METER_CTRL0_PORT0_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_BCAST_METER_CTRL1    0x0a45
-#define    RTL8367C_STORM_BCAST_METER_CTRL1_PORT3_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_BCAST_METER_CTRL1_PORT3_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_BCAST_METER_CTRL1_PORT2_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_BCAST_METER_CTRL1_PORT2_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_BCAST_METER_CTRL2    0x0a46
-#define    RTL8367C_STORM_BCAST_METER_CTRL2_PORT5_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_BCAST_METER_CTRL2_PORT5_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_BCAST_METER_CTRL2_PORT4_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_BCAST_METER_CTRL2_PORT4_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_BCAST_METER_CTRL3    0x0a47
-#define    RTL8367C_STORM_BCAST_METER_CTRL3_PORT7_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_BCAST_METER_CTRL3_PORT7_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_BCAST_METER_CTRL3_PORT6_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_BCAST_METER_CTRL3_PORT6_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_BCAST_METER_CTRL4    0x0a48
-#define    RTL8367C_STORM_BCAST_METER_CTRL4_PORT9_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_BCAST_METER_CTRL4_PORT9_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_BCAST_METER_CTRL4_PORT8_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_BCAST_METER_CTRL4_PORT8_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_BCAST_METER_CTRL5    0x0a49
-#define    RTL8367C_STORM_BCAST_METER_CTRL5_OFFSET    0
-#define    RTL8367C_STORM_BCAST_METER_CTRL5_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_MCAST_METER_CTRL0    0x0a4c
-#define    RTL8367C_STORM_MCAST_METER_CTRL0_PORT1_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_MCAST_METER_CTRL0_PORT1_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_MCAST_METER_CTRL0_PORT0_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_MCAST_METER_CTRL0_PORT0_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_MCAST_METER_CTRL1    0x0a4d
-#define    RTL8367C_STORM_MCAST_METER_CTRL1_PORT3_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_MCAST_METER_CTRL1_PORT3_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_MCAST_METER_CTRL1_PORT2_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_MCAST_METER_CTRL1_PORT2_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_MCAST_METER_CTRL2    0x0a4e
-#define    RTL8367C_STORM_MCAST_METER_CTRL2_PORT5_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_MCAST_METER_CTRL2_PORT5_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_MCAST_METER_CTRL2_PORT4_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_MCAST_METER_CTRL2_PORT4_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_MCAST_METER_CTRL3    0x0a4f
-#define    RTL8367C_STORM_MCAST_METER_CTRL3_PORT7_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_MCAST_METER_CTRL3_PORT7_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_MCAST_METER_CTRL3_PORT6_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_MCAST_METER_CTRL3_PORT6_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_MCAST_METER_CTRL4    0x0a50
-#define    RTL8367C_STORM_MCAST_METER_CTRL4_PORT9_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_MCAST_METER_CTRL4_PORT9_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_MCAST_METER_CTRL4_PORT8_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_MCAST_METER_CTRL4_PORT8_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_MCAST_METER_CTRL5    0x0a51
-#define    RTL8367C_STORM_MCAST_METER_CTRL5_OFFSET    0
-#define    RTL8367C_STORM_MCAST_METER_CTRL5_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNDA_METER_CTRL0    0x0a54
-#define    RTL8367C_STORM_UNDA_METER_CTRL0_PORT1_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNDA_METER_CTRL0_PORT1_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNDA_METER_CTRL0_PORT0_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNDA_METER_CTRL0_PORT0_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNDA_METER_CTRL1    0x0a55
-#define    RTL8367C_STORM_UNDA_METER_CTRL1_PORT3_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNDA_METER_CTRL1_PORT3_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNDA_METER_CTRL1_PORT2_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNDA_METER_CTRL1_PORT2_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNDA_METER_CTRL2    0x0a56
-#define    RTL8367C_STORM_UNDA_METER_CTRL2_PORT5_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNDA_METER_CTRL2_PORT5_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNDA_METER_CTRL2_PORT4_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNDA_METER_CTRL2_PORT4_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNDA_METER_CTRL3    0x0a57
-#define    RTL8367C_STORM_UNDA_METER_CTRL3_PORT7_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNDA_METER_CTRL3_PORT7_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNDA_METER_CTRL3_PORT6_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNDA_METER_CTRL3_PORT6_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNDA_METER_CTRL4    0x0a58
-#define    RTL8367C_STORM_UNDA_METER_CTRL4_PORT9_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNDA_METER_CTRL4_PORT9_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNDA_METER_CTRL4_PORT8_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNDA_METER_CTRL4_PORT8_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNDA_METER_CTRL5    0x0a59
-#define    RTL8367C_STORM_UNDA_METER_CTRL5_OFFSET    0
-#define    RTL8367C_STORM_UNDA_METER_CTRL5_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNMC_METER_CTRL0    0x0a5c
-#define    RTL8367C_STORM_UNMC_METER_CTRL0_PORT1_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNMC_METER_CTRL0_PORT1_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNMC_METER_CTRL0_PORT0_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNMC_METER_CTRL0_PORT0_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNMC_METER_CTRL1    0x0a5d
-#define    RTL8367C_STORM_UNMC_METER_CTRL1_PORT3_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNMC_METER_CTRL1_PORT3_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNMC_METER_CTRL1_PORT2_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNMC_METER_CTRL1_PORT2_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNMC_METER_CTRL2    0x0a5e
-#define    RTL8367C_STORM_UNMC_METER_CTRL2_PORT5_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNMC_METER_CTRL2_PORT5_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNMC_METER_CTRL2_PORT4_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNMC_METER_CTRL2_PORT4_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNMC_METER_CTRL3    0x0a5f
-#define    RTL8367C_STORM_UNMC_METER_CTRL3_PORT7_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNMC_METER_CTRL3_PORT7_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNMC_METER_CTRL3_PORT6_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNMC_METER_CTRL3_PORT6_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_EXT_CFG    0x0a60
-#define    RTL8367C_STORM_EXT_EN_PORTMASK_EXT_OFFSET    14
-#define    RTL8367C_STORM_EXT_EN_PORTMASK_EXT_MASK    0x4000
-#define    RTL8367C_STORM_UNKNOWN_MCAST_EXT_EN_OFFSET    13
-#define    RTL8367C_STORM_UNKNOWN_MCAST_EXT_EN_MASK    0x2000
-#define    RTL8367C_STORM_UNKNOWN_UCAST_EXT_EN_OFFSET    12
-#define    RTL8367C_STORM_UNKNOWN_UCAST_EXT_EN_MASK    0x1000
-#define    RTL8367C_STORM_MCAST_EXT_EN_OFFSET    11
-#define    RTL8367C_STORM_MCAST_EXT_EN_MASK    0x800
-#define    RTL8367C_STORM_BCAST_EXT_EN_OFFSET    10
-#define    RTL8367C_STORM_BCAST_EXT_EN_MASK    0x400
-#define    RTL8367C_STORM_EXT_EN_PORTMASK_OFFSET    0
-#define    RTL8367C_STORM_EXT_EN_PORTMASK_MASK    0x3FF
-
-#define    RTL8367C_REG_STORM_EXT_MTRIDX_CFG0    0x0a61
-#define    RTL8367C_MC_STORM_EXT_METERIDX_OFFSET    8
-#define    RTL8367C_MC_STORM_EXT_METERIDX_MASK    0x3F00
-#define    RTL8367C_BC_STORM_EXT_METERIDX_OFFSET    0
-#define    RTL8367C_BC_STORM_EXT_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_EXT_MTRIDX_CFG1    0x0a62
-#define    RTL8367C_UNMC_STORM_EXT_METERIDX_OFFSET    8
-#define    RTL8367C_UNMC_STORM_EXT_METERIDX_MASK    0x3F00
-#define    RTL8367C_UNUC_STORM_EXT_METERIDX_OFFSET    0
-#define    RTL8367C_UNUC_STORM_EXT_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNMC_METER_CTRL4    0x0a63
-#define    RTL8367C_STORM_UNMC_METER_CTRL4_PORT9_METERIDX_OFFSET    8
-#define    RTL8367C_STORM_UNMC_METER_CTRL4_PORT9_METERIDX_MASK    0x3F00
-#define    RTL8367C_STORM_UNMC_METER_CTRL4_PORT8_METERIDX_OFFSET    0
-#define    RTL8367C_STORM_UNMC_METER_CTRL4_PORT8_METERIDX_MASK    0x3F
-
-#define    RTL8367C_REG_STORM_UNMC_METER_CTRL5    0x0a64
-#define    RTL8367C_STORM_UNMC_METER_CTRL5_OFFSET    0
-#define    RTL8367C_STORM_UNMC_METER_CTRL5_MASK    0x3F
-
-#define    RTL8367C_REG_OAM_PARSER_CTRL0    0x0a70
-#define    RTL8367C_PORT7_PARACT_OFFSET    14
-#define    RTL8367C_PORT7_PARACT_MASK    0xC000
-#define    RTL8367C_PORT6_PARACT_OFFSET    12
-#define    RTL8367C_PORT6_PARACT_MASK    0x3000
-#define    RTL8367C_PORT5_PARACT_OFFSET    10
-#define    RTL8367C_PORT5_PARACT_MASK    0xC00
-#define    RTL8367C_PORT4_PARACT_OFFSET    8
-#define    RTL8367C_PORT4_PARACT_MASK    0x300
-#define    RTL8367C_PORT3_PARACT_OFFSET    6
-#define    RTL8367C_PORT3_PARACT_MASK    0xC0
-#define    RTL8367C_PORT2_PARACT_OFFSET    4
-#define    RTL8367C_PORT2_PARACT_MASK    0x30
-#define    RTL8367C_PORT1_PARACT_OFFSET    2
-#define    RTL8367C_PORT1_PARACT_MASK    0xC
-#define    RTL8367C_PORT0_PARACT_OFFSET    0
-#define    RTL8367C_PORT0_PARACT_MASK    0x3
-
-#define    RTL8367C_REG_OAM_PARSER_CTRL1    0x0a71
-#define    RTL8367C_PORT10_PARACT_OFFSET    4
-#define    RTL8367C_PORT10_PARACT_MASK    0x30
-#define    RTL8367C_PORT9_PARACT_OFFSET    2
-#define    RTL8367C_PORT9_PARACT_MASK    0xC
-#define    RTL8367C_PORT8_PARACT_OFFSET    0
-#define    RTL8367C_PORT8_PARACT_MASK    0x3
-
-#define    RTL8367C_REG_OAM_MULTIPLEXER_CTRL0    0x0a72
-#define    RTL8367C_PORT7_MULACT_OFFSET    14
-#define    RTL8367C_PORT7_MULACT_MASK    0xC000
-#define    RTL8367C_PORT6_MULACT_OFFSET    12
-#define    RTL8367C_PORT6_MULACT_MASK    0x3000
-#define    RTL8367C_PORT5_MULACT_OFFSET    10
-#define    RTL8367C_PORT5_MULACT_MASK    0xC00
-#define    RTL8367C_PORT4_MULACT_OFFSET    8
-#define    RTL8367C_PORT4_MULACT_MASK    0x300
-#define    RTL8367C_PORT3_MULACT_OFFSET    6
-#define    RTL8367C_PORT3_MULACT_MASK    0xC0
-#define    RTL8367C_PORT2_MULACT_OFFSET    4
-#define    RTL8367C_PORT2_MULACT_MASK    0x30
-#define    RTL8367C_PORT1_MULACT_OFFSET    2
-#define    RTL8367C_PORT1_MULACT_MASK    0xC
-#define    RTL8367C_PORT0_MULACT_OFFSET    0
-#define    RTL8367C_PORT0_MULACT_MASK    0x3
-
-#define    RTL8367C_REG_OAM_MULTIPLEXER_CTRL1    0x0a73
-#define    RTL8367C_PORT10_MULACT_OFFSET    4
-#define    RTL8367C_PORT10_MULACT_MASK    0x30
-#define    RTL8367C_PORT9_MULACT_OFFSET    2
-#define    RTL8367C_PORT9_MULACT_MASK    0xC
-#define    RTL8367C_PORT8_MULACT_OFFSET    0
-#define    RTL8367C_PORT8_MULACT_MASK    0x3
-
-#define    RTL8367C_REG_OAM_CTRL    0x0a74
-#define    RTL8367C_OAM_CTRL_OFFSET    0
-#define    RTL8367C_OAM_CTRL_MASK    0x1
-
-#define    RTL8367C_REG_DOT1X_PORT_ENABLE    0x0a80
-#define    RTL8367C_DOT1X_PORT_ENABLE_OFFSET    0
-#define    RTL8367C_DOT1X_PORT_ENABLE_MASK    0x7FF
-
-#define    RTL8367C_REG_DOT1X_MAC_ENABLE    0x0a81
-#define    RTL8367C_DOT1X_MAC_ENABLE_OFFSET    0
-#define    RTL8367C_DOT1X_MAC_ENABLE_MASK    0x7FF
-
-#define    RTL8367C_REG_DOT1X_PORT_AUTH    0x0a82
-#define    RTL8367C_DOT1X_PORT_AUTH_OFFSET    0
-#define    RTL8367C_DOT1X_PORT_AUTH_MASK    0x7FF
-
-#define    RTL8367C_REG_DOT1X_PORT_OPDIR    0x0a83
-#define    RTL8367C_DOT1X_PORT_OPDIR_OFFSET    0
-#define    RTL8367C_DOT1X_PORT_OPDIR_MASK    0x7FF
-
-#define    RTL8367C_REG_DOT1X_UNAUTH_ACT_W0    0x0a84
-#define    RTL8367C_DOT1X_PORT7_UNAUTHBH_OFFSET    14
-#define    RTL8367C_DOT1X_PORT7_UNAUTHBH_MASK    0xC000
-#define    RTL8367C_DOT1X_PORT6_UNAUTHBH_OFFSET    12
-#define    RTL8367C_DOT1X_PORT6_UNAUTHBH_MASK    0x3000
-#define    RTL8367C_DOT1X_PORT5_UNAUTHBH_OFFSET    10
-#define    RTL8367C_DOT1X_PORT5_UNAUTHBH_MASK    0xC00
-#define    RTL8367C_DOT1X_PORT4_UNAUTHBH_OFFSET    8
-#define    RTL8367C_DOT1X_PORT4_UNAUTHBH_MASK    0x300
-#define    RTL8367C_DOT1X_PORT3_UNAUTHBH_OFFSET    6
-#define    RTL8367C_DOT1X_PORT3_UNAUTHBH_MASK    0xC0
-#define    RTL8367C_DOT1X_PORT2_UNAUTHBH_OFFSET    4
-#define    RTL8367C_DOT1X_PORT2_UNAUTHBH_MASK    0x30
-#define    RTL8367C_DOT1X_PORT1_UNAUTHBH_OFFSET    2
-#define    RTL8367C_DOT1X_PORT1_UNAUTHBH_MASK    0xC
-#define    RTL8367C_DOT1X_PORT0_UNAUTHBH_OFFSET    0
-#define    RTL8367C_DOT1X_PORT0_UNAUTHBH_MASK    0x3
-
-#define    RTL8367C_REG_DOT1X_UNAUTH_ACT_W1    0x0a85
-#define    RTL8367C_DOT1X_PORT10_UNAUTHBH_OFFSET    4
-#define    RTL8367C_DOT1X_PORT10_UNAUTHBH_MASK    0x30
-#define    RTL8367C_DOT1X_PORT9_UNAUTHBH_OFFSET    2
-#define    RTL8367C_DOT1X_PORT9_UNAUTHBH_MASK    0xC
-#define    RTL8367C_DOT1X_PORT8_UNAUTHBH_OFFSET    0
-#define    RTL8367C_DOT1X_PORT8_UNAUTHBH_MASK    0x3
-
-#define    RTL8367C_REG_DOT1X_CFG    0x0a86
-#define    RTL8367C_DOT1X_GVOPDIR_OFFSET    6
-#define    RTL8367C_DOT1X_GVOPDIR_MASK    0x40
-#define    RTL8367C_DOT1X_MAC_OPDIR_OFFSET    5
-#define    RTL8367C_DOT1X_MAC_OPDIR_MASK    0x20
-#define    RTL8367C_DOT1X_GVIDX_OFFSET    0
-#define    RTL8367C_DOT1X_GVIDX_MASK    0x1F
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL0    0x0a87
-#define    RTL8367C_L2_LRN_CNT_CTRL0_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL0_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL1    0x0a88
-#define    RTL8367C_L2_LRN_CNT_CTRL1_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL1_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL2    0x0a89
-#define    RTL8367C_L2_LRN_CNT_CTRL2_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL3    0x0a8a
-#define    RTL8367C_L2_LRN_CNT_CTRL3_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL3_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL4    0x0a8b
-#define    RTL8367C_L2_LRN_CNT_CTRL4_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL4_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL5    0x0a8c
-#define    RTL8367C_L2_LRN_CNT_CTRL5_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL5_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL6    0x0a8d
-#define    RTL8367C_L2_LRN_CNT_CTRL6_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL6_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL7    0x0a8e
-#define    RTL8367C_L2_LRN_CNT_CTRL7_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL7_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL8    0x0a8f
-#define    RTL8367C_L2_LRN_CNT_CTRL8_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL8_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL9    0x0a90
-#define    RTL8367C_L2_LRN_CNT_CTRL9_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL9_MASK    0x1FFF
-
-#define    RTL8367C_REG_L2_LRN_CNT_CTRL10    0x0a92
-#define    RTL8367C_L2_LRN_CNT_CTRL10_OFFSET    0
-#define    RTL8367C_L2_LRN_CNT_CTRL10_MASK    0x1FFF
-
-#define    RTL8367C_REG_LUT_LRN_UNDER_STATUS    0x0a91
-#define    RTL8367C_LUT_LRN_UNDER_STATUS_OFFSET    0
-#define    RTL8367C_LUT_LRN_UNDER_STATUS_MASK    0x7FF
-
-#define    RTL8367C_REG_L2_SA_MOVING_FORBID    0x0aa0
-#define    RTL8367C_L2_SA_MOVING_FORBID_OFFSET    0
-#define    RTL8367C_L2_SA_MOVING_FORBID_MASK    0x7FF
-
-#define    RTL8367C_REG_DRPORT_LEARN_CTRL    0x0aa1
-#define    RTL8367C_FORBID1_OFFSET    1
-#define    RTL8367C_FORBID1_MASK    0x2
-#define    RTL8367C_FORBID0_OFFSET    0
-#define    RTL8367C_FORBID0_MASK    0x1
-
-#define    RTL8367C_REG_L2_DUMMY02    0x0aa2
-
-#define    RTL8367C_REG_L2_DUMMY03    0x0aa3
-
-#define    RTL8367C_REG_L2_DUMMY04    0x0aa4
-
-#define    RTL8367C_REG_L2_DUMMY05    0x0aa5
-
-#define    RTL8367C_REG_L2_DUMMY06    0x0aa6
-
-#define    RTL8367C_REG_L2_DUMMY07    0x0aa7
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_00    0x0AC0
-#define    RTL8367C_IPMC_GROUP_PMSK_00_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_00_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_01    0x0AC1
-#define    RTL8367C_IPMC_GROUP_PMSK_01_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_01_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_02    0x0AC2
-#define    RTL8367C_IPMC_GROUP_PMSK_02_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_02_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_03    0x0AC3
-#define    RTL8367C_IPMC_GROUP_PMSK_03_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_03_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_04    0x0AC4
-#define    RTL8367C_IPMC_GROUP_PMSK_04_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_04_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_05    0x0AC5
-#define    RTL8367C_IPMC_GROUP_PMSK_05_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_05_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_06    0x0AC6
-#define    RTL8367C_IPMC_GROUP_PMSK_06_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_06_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_07    0x0AC7
-#define    RTL8367C_IPMC_GROUP_PMSK_07_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_07_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_08    0x0AC8
-#define    RTL8367C_IPMC_GROUP_PMSK_08_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_08_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_09    0x0AC9
-#define    RTL8367C_IPMC_GROUP_PMSK_09_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_09_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_10    0x0ACA
-#define    RTL8367C_IPMC_GROUP_PMSK_10_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_10_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_11    0x0ACB
-#define    RTL8367C_IPMC_GROUP_PMSK_11_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_11_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_12    0x0ACC
-#define    RTL8367C_IPMC_GROUP_PMSK_12_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_12_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_13    0x0ACD
-#define    RTL8367C_IPMC_GROUP_PMSK_13_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_13_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_14    0x0ACE
-#define    RTL8367C_IPMC_GROUP_PMSK_14_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_14_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_15    0x0ACF
-#define    RTL8367C_IPMC_GROUP_PMSK_15_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_15_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_16    0x0AD0
-#define    RTL8367C_IPMC_GROUP_PMSK_16_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_16_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_17    0x0AD1
-#define    RTL8367C_IPMC_GROUP_PMSK_17_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_17_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_18    0x0AD2
-#define    RTL8367C_IPMC_GROUP_PMSK_18_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_18_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_19    0x0AD3
-#define    RTL8367C_IPMC_GROUP_PMSK_19_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_19_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_20    0x0AD4
-#define    RTL8367C_IPMC_GROUP_PMSK_20_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_20_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_21    0x0AD5
-#define    RTL8367C_IPMC_GROUP_PMSK_21_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_21_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_22    0x0AD6
-#define    RTL8367C_IPMC_GROUP_PMSK_22_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_22_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_23    0x0AD7
-#define    RTL8367C_IPMC_GROUP_PMSK_23_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_23_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_24    0x0AD8
-#define    RTL8367C_IPMC_GROUP_PMSK_24_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_24_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_25    0x0AD9
-#define    RTL8367C_IPMC_GROUP_PMSK_25_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_25_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_26    0x0ADA
-#define    RTL8367C_IPMC_GROUP_PMSK_26_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_26_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_27    0x0ADB
-#define    RTL8367C_IPMC_GROUP_PMSK_27_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_27_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_28    0x0ADC
-#define    RTL8367C_IPMC_GROUP_PMSK_28_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_28_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_29    0x0ADD
-#define    RTL8367C_IPMC_GROUP_PMSK_29_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_29_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_30    0x0ADE
-#define    RTL8367C_IPMC_GROUP_PMSK_30_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_30_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_31    0x0ADF
-#define    RTL8367C_IPMC_GROUP_PMSK_31_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_31_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_32    0x0AE0
-#define    RTL8367C_IPMC_GROUP_PMSK_32_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_32_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_33    0x0AE1
-#define    RTL8367C_IPMC_GROUP_PMSK_33_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_33_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_34    0x0AE2
-#define    RTL8367C_IPMC_GROUP_PMSK_34_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_34_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_35    0x0AE3
-#define    RTL8367C_IPMC_GROUP_PMSK_35_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_35_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_36    0x0AE4
-#define    RTL8367C_IPMC_GROUP_PMSK_36_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_36_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_37    0x0AE5
-#define    RTL8367C_IPMC_GROUP_PMSK_37_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_37_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_38    0x0AE6
-#define    RTL8367C_IPMC_GROUP_PMSK_38_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_38_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_39    0x0AE7
-#define    RTL8367C_IPMC_GROUP_PMSK_39_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_39_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_40    0x0AE8
-#define    RTL8367C_IPMC_GROUP_PMSK_40_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_40_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_41    0x0AE9
-#define    RTL8367C_IPMC_GROUP_PMSK_41_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_41_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_42    0x0AEA
-#define    RTL8367C_IPMC_GROUP_PMSK_42_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_42_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_43    0x0AEB
-#define    RTL8367C_IPMC_GROUP_PMSK_43_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_43_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_44    0x0AEC
-#define    RTL8367C_IPMC_GROUP_PMSK_44_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_44_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_45    0x0AED
-#define    RTL8367C_IPMC_GROUP_PMSK_45_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_45_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_46    0x0AEE
-#define    RTL8367C_IPMC_GROUP_PMSK_46_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_46_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_47    0x0AEF
-#define    RTL8367C_IPMC_GROUP_PMSK_47_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_47_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_48    0x0AF0
-#define    RTL8367C_IPMC_GROUP_PMSK_48_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_48_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_49    0x0AF1
-#define    RTL8367C_IPMC_GROUP_PMSK_49_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_49_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_50    0x0AF2
-#define    RTL8367C_IPMC_GROUP_PMSK_50_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_50_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_51    0x0AF3
-#define    RTL8367C_IPMC_GROUP_PMSK_51_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_51_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_52    0x0AF4
-#define    RTL8367C_IPMC_GROUP_PMSK_52_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_52_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_53    0x0AF5
-#define    RTL8367C_IPMC_GROUP_PMSK_53_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_53_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_54    0x0AF6
-#define    RTL8367C_IPMC_GROUP_PMSK_54_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_54_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_55    0x0AF7
-#define    RTL8367C_IPMC_GROUP_PMSK_55_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_55_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_56    0x0AF8
-#define    RTL8367C_IPMC_GROUP_PMSK_56_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_56_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_57    0x0AF9
-#define    RTL8367C_IPMC_GROUP_PMSK_57_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_57_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_58    0x0AFA
-#define    RTL8367C_IPMC_GROUP_PMSK_58_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_58_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_59    0x0AFB
-#define    RTL8367C_IPMC_GROUP_PMSK_59_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_59_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_60    0x0AFC
-#define    RTL8367C_IPMC_GROUP_PMSK_60_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_60_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_61    0x0AFD
-#define    RTL8367C_IPMC_GROUP_PMSK_61_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_61_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_62    0x0AFE
-#define    RTL8367C_IPMC_GROUP_PMSK_62_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_62_MASK    0x7FF
-
-#define    RTL8367C_REG_IPMC_GROUP_PMSK_63    0x0AFF
-#define    RTL8367C_IPMC_GROUP_PMSK_63_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_PMSK_63_MASK    0x7FF
-
-/* (16'h0b00)mltvlan_reg */
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY0_CTRL0    0x0b00
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY0_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY0_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY0_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY0_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY0_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY0_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY0_CTRL1    0x0b01
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY0_CTRL2    0x0b02
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY0_CTRL3    0x0b03
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY0_CTRL4    0x0b04
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY1_CTRL0    0x0b05
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY1_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY1_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY1_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY1_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY1_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY1_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY1_CTRL1    0x0b06
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY1_CTRL2    0x0b07
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY1_CTRL3    0x0b08
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY1_CTRL4    0x0b09
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY2_CTRL0    0x0b0a
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY2_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY2_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY2_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY2_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY2_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY2_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY2_CTRL1    0x0b0b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY2_CTRL2    0x0b0c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY2_CTRL3    0x0b0d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY2_CTRL4    0x0b0e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY3_CTRL0    0x0b0f
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY3_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY3_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY3_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY3_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY3_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY3_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY3_CTRL1    0x0b10
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY3_CTRL2    0x0b11
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY3_CTRL3    0x0b12
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY3_CTRL4    0x0b13
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY4_CTRL0    0x0b14
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY4_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY4_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY4_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY4_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY4_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY4_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY4_CTRL1    0x0b15
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY4_CTRL2    0x0b16
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY4_CTRL3    0x0b17
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY4_CTRL4    0x0b18
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY5_CTRL0    0x0b19
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY5_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY5_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY5_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY5_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY5_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY5_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY5_CTRL1    0x0b1a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY5_CTRL2    0x0b1b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY5_CTRL3    0x0b1c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY5_CTRL4    0x0b1d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY6_CTRL0    0x0b1e
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY6_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY6_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY6_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY6_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY6_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY6_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY6_CTRL1    0x0b1f
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY6_CTRL2    0x0b20
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY6_CTRL3    0x0b21
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY6_CTRL4    0x0b22
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY7_CTRL0    0x0b23
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY7_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY7_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY7_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY7_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY7_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY7_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY7_CTRL1    0x0b24
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY7_CTRL2    0x0b25
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY7_CTRL3    0x0b26
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY7_CTRL4    0x0b27
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY8_CTRL0    0x0b28
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY8_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY8_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY8_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY8_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY8_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY8_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY8_CTRL1    0x0b29
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY8_CTRL2    0x0b2a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY8_CTRL3    0x0b2b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY8_CTRL4    0x0b2c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY9_CTRL0    0x0b2d
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY9_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY9_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY9_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY9_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY9_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY9_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY9_CTRL1    0x0b2e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY9_CTRL2    0x0b2f
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY9_CTRL3    0x0b30
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY9_CTRL4    0x0b31
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY10_CTRL0    0x0b32
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY10_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY10_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY10_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY10_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY10_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY10_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY10_CTRL1    0x0b33
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY10_CTRL2    0x0b34
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY10_CTRL3    0x0b35
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY10_CTRL4    0x0b36
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY11_CTRL0    0x0b37
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY11_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY11_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY11_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY11_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY11_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY11_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY11_CTRL1    0x0b38
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY11_CTRL2    0x0b39
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY11_CTRL3    0x0b3a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY11_CTRL4    0x0b3b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY12_CTRL0    0x0b3c
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY12_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY12_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY12_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY12_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY12_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY12_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY12_CTRL1    0x0b3d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY12_CTRL2    0x0b3e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY12_CTRL3    0x0b3f
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY12_CTRL4    0x0b40
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY13_CTRL0    0x0b41
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY13_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY13_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY13_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY13_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY13_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY13_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY13_CTRL1    0x0b42
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY13_CTRL2    0x0b43
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY13_CTRL3    0x0b44
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY13_CTRL4    0x0b45
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY14_CTRL0    0x0b46
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY14_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY14_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY14_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY14_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY14_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY14_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY14_CTRL1    0x0b47
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY14_CTRL2    0x0b48
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY14_CTRL3    0x0b49
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY14_CTRL4    0x0b4a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY15_CTRL0    0x0b4b
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY15_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY15_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY15_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY15_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY15_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY15_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY15_CTRL1    0x0b4c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY15_CTRL2    0x0b4d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY15_CTRL3    0x0b4e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY15_CTRL4    0x0b4f
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY16_CTRL0    0x0b50
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY16_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY16_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY16_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY16_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY16_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY16_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY16_CTRL1    0x0b51
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY16_CTRL2    0x0b52
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY16_CTRL3    0x0b53
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY16_CTRL4    0x0b54
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY17_CTRL0    0x0b55
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY17_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY17_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY17_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY17_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY17_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY17_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY17_CTRL1    0x0b56
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY17_CTRL2    0x0b57
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY17_CTRL3    0x0b58
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY17_CTRL4    0x0b59
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY18_CTRL0    0x0b5a
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY18_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY18_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY18_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY18_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY18_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY18_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY18_CTRL1    0x0b5b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY18_CTRL2    0x0b5c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY18_CTRL3    0x0b5d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY18_CTRL4    0x0b5e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY19_CTRL0    0x0b5f
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY19_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY19_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY19_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY19_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY19_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY19_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY19_CTRL1    0x0b60
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY19_CTRL2    0x0b61
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY19_CTRL3    0x0b62
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY19_CTRL4    0x0b63
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY20_CTRL0    0x0b64
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY20_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY20_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY20_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY20_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY20_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY20_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY20_CTRL1    0x0b65
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY20_CTRL2    0x0b66
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY20_CTRL3    0x0b67
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY20_CTRL4    0x0b68
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY21_CTRL0    0x0b69
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY21_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY21_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY21_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY21_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY21_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY21_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY21_CTRL1    0x0b6a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY21_CTRL2    0x0b6b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY21_CTRL3    0x0b6c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY21_CTRL4    0x0b6d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY22_CTRL0    0x0b6e
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY22_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY22_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY22_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY22_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY22_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY22_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY22_CTRL1    0x0b6f
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY22_CTRL2    0x0b70
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY22_CTRL3    0x0b71
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY22_CTRL4    0x0b72
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY23_CTRL0    0x0b73
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY23_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY23_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY23_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY23_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY23_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY23_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY23_CTRL1    0x0b74
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY23_CTRL2    0x0b75
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY23_CTRL3    0x0b76
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY23_CTRL4    0x0b77
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY24_CTRL0    0x0b78
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY24_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY24_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY24_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY24_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY24_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY24_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY24_CTRL1    0x0b79
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY24_CTRL2    0x0b7a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY24_CTRL3    0x0b7b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY24_CTRL4    0x0b7c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY25_CTRL0    0x0b7d
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY25_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY25_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY25_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY25_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY25_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY25_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY25_CTRL1    0x0b7e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY25_CTRL2    0x0b7f
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY25_CTRL3    0x0b80
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY25_CTRL4    0x0b81
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY26_CTRL0    0x0b82
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY26_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY26_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY26_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY26_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY26_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY26_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY26_CTRL1    0x0b83
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY26_CTRL2    0x0b84
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY26_CTRL3    0x0b85
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY26_CTRL4    0x0b86
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY27_CTRL0    0x0b87
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY27_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY27_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY27_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY27_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY27_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY27_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY27_CTRL1    0x0b88
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY27_CTRL2    0x0b89
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY27_CTRL3    0x0b8a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY27_CTRL4    0x0b8b
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY28_CTRL0    0x0b8c
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY28_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY28_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY28_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY28_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY28_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY28_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY28_CTRL1    0x0b8d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY28_CTRL2    0x0b8e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY28_CTRL3    0x0b8f
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY28_CTRL4    0x0b90
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY29_CTRL0    0x0b91
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY29_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY29_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY29_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY29_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY29_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY29_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY29_CTRL1    0x0b92
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY29_CTRL2    0x0b93
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY29_CTRL3    0x0b94
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY29_CTRL4    0x0b95
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY30_CTRL0    0x0b96
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY30_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY30_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY30_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY30_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY30_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY30_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY30_CTRL1    0x0b97
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY30_CTRL2    0x0b98
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY30_CTRL3    0x0b99
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY30_CTRL4    0x0b9a
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY31_CTRL0    0x0b9b
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY31_CTRL0_VALID_OFFSET    7
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY31_CTRL0_VALID_MASK    0x80
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY31_CTRL0_FORMAT_OFFSET    6
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY31_CTRL0_FORMAT_MASK    0x40
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY31_CTRL0_SVIDX_OFFSET    0
-#define    RTL8367C_SVLAN_MCAST2S_ENTRY31_CTRL0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY31_CTRL1    0x0b9c
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY31_CTRL2    0x0b9d
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY31_CTRL3    0x0b9e
-
-#define    RTL8367C_REG_SVLAN_MCAST2S_ENTRY31_CTRL4    0x0b9f
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_0    0x0ba0
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_1    0x0ba1
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_2    0x0ba2
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_3    0x0ba3
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_4    0x0ba4
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_5    0x0ba5
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_6    0x0ba6
-
-#define    RTL8367C_REG_MLTVLAN_DUMMY_7    0x0ba7
-
-/* (16'h0c00)svlan_reg */
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG0_CTRL1    0x0c01
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG0_CTRL2    0x0c02
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG0_CTRL3    0x0c03
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG1_CTRL1    0x0c04
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG1_CTRL2    0x0c05
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG1_CTRL3    0x0c06
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG2_CTRL1    0x0c07
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG2_CTRL2    0x0c08
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG2_CTRL3    0x0c09
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG3_CTRL1    0x0c0a
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG3_CTRL2    0x0c0b
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG3_CTRL3    0x0c0c
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG4_CTRL1    0x0c0d
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG4_CTRL2    0x0c0e
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG4_CTRL3    0x0c0f
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG5_CTRL1    0x0c10
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG5_CTRL2    0x0c11
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG5_CTRL3    0x0c12
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG6_CTRL1    0x0c13
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG6_CTRL2    0x0c14
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG6_CTRL3    0x0c15
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG7_CTRL1    0x0c16
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG7_CTRL2    0x0c17
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG7_CTRL3    0x0c18
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG8_CTRL1    0x0c19
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG8_CTRL2    0x0c1a
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG8_CTRL3    0x0c1b
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG9_CTRL1    0x0c1c
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG9_CTRL2    0x0c1d
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG9_CTRL3    0x0c1e
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG10_CTRL1    0x0c1f
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG10_CTRL2    0x0c20
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG10_CTRL3    0x0c21
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG11_CTRL1    0x0c22
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG11_CTRL2    0x0c23
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG11_CTRL3    0x0c24
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG12_CTRL1    0x0c25
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG12_CTRL2    0x0c26
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG12_CTRL3    0x0c27
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG13_CTRL1    0x0c28
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG13_CTRL2    0x0c29
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG13_CTRL3    0x0c2a
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG14_CTRL1    0x0c2b
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG14_CTRL2    0x0c2c
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG14_CTRL3    0x0c2d
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG15_CTRL1    0x0c2e
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG15_CTRL2    0x0c2f
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG15_CTRL3    0x0c30
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG16_CTRL1    0x0c31
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG16_CTRL2    0x0c32
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG16_CTRL3    0x0c33
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG17_CTRL1    0x0c34
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG17_CTRL2    0x0c35
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG17_CTRL3    0x0c36
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG18_CTRL1    0x0c37
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG18_CTRL2    0x0c38
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG18_CTRL3    0x0c39
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG19_CTRL1    0x0c3a
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG19_CTRL2    0x0c3b
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG19_CTRL3    0x0c3c
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG20_CTRL1    0x0c3d
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG20_CTRL2    0x0c3e
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG20_CTRL3    0x0c3f
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG21_CTRL1    0x0c40
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG21_CTRL2    0x0c41
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG21_CTRL3    0x0c42
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG22_CTRL1    0x0c43
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG22_CTRL2    0x0c44
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG22_CTRL3    0x0c45
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG23_CTRL1    0x0c46
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG23_CTRL2    0x0c47
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG23_CTRL3    0x0c48
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG24_CTRL1    0x0c49
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG24_CTRL2    0x0c4a
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG24_CTRL3    0x0c4b
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG25_CTRL1    0x0c4c
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG25_CTRL2    0x0c4d
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG25_CTRL3    0x0c4e
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG26_CTRL1    0x0c4f
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG26_CTRL2    0x0c50
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG26_CTRL3    0x0c51
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG27_CTRL1    0x0c52
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG27_CTRL2    0x0c53
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG27_CTRL3    0x0c54
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG28_CTRL1    0x0c55
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG28_CTRL2    0x0c56
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG28_CTRL3    0x0c57
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG29_CTRL1    0x0c58
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG29_CTRL2    0x0c59
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG29_CTRL3    0x0c5a
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG30_CTRL1    0x0c5b
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG30_CTRL2    0x0c5c
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG30_CTRL3    0x0c5d
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG31_CTRL1    0x0c5e
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG31_CTRL2    0x0c5f
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG31_CTRL3    0x0c60
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG32_CTRL1    0x0c61
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG32_CTRL2    0x0c62
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG32_CTRL3    0x0c63
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG33_CTRL1    0x0c64
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG33_CTRL2    0x0c65
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG33_CTRL3    0x0c66
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG34_CTRL1    0x0c67
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG34_CTRL2    0x0c68
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG34_CTRL3    0x0c69
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG35_CTRL1    0x0c6a
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG35_CTRL2    0x0c6b
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG35_CTRL3    0x0c6c
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG36_CTRL1    0x0c6d
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG36_CTRL2    0x0c6e
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG36_CTRL3    0x0c6f
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG37_CTRL1    0x0c70
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG37_CTRL2    0x0c71
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG37_CTRL3    0x0c72
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG38_CTRL1    0x0c73
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG38_CTRL2    0x0c74
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG38_CTRL3    0x0c75
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG39_CTRL1    0x0c76
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG39_CTRL2    0x0c77
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG39_CTRL3    0x0c78
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG40_CTRL1    0x0c79
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG40_CTRL2    0x0c7a
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG40_CTRL3    0x0c7b
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG41_CTRL1    0x0c7c
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG41_CTRL2    0x0c7d
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG41_CTRL3    0x0c7e
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG42_CTRL1    0x0c7f
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG42_CTRL2    0x0c80
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG42_CTRL3    0x0c81
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG43_CTRL1    0x0c82
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG43_CTRL2    0x0c83
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG43_CTRL3    0x0c84
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG44_CTRL1    0x0c85
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG44_CTRL2    0x0c86
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG44_CTRL3    0x0c87
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG45_CTRL1    0x0c88
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG45_CTRL2    0x0c89
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG45_CTRL3    0x0c8a
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG46_CTRL1    0x0c8b
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG46_CTRL2    0x0c8c
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG46_CTRL3    0x0c8d
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG47_CTRL1    0x0c8e
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG47_CTRL2    0x0c8f
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG47_CTRL3    0x0c90
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG48_CTRL1    0x0c91
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG48_CTRL2    0x0c92
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG48_CTRL3    0x0c93
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG49_CTRL1    0x0c94
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG49_CTRL2    0x0c95
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG49_CTRL3    0x0c96
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG50_CTRL1    0x0c97
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG50_CTRL2    0x0c98
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG50_CTRL3    0x0c99
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG51_CTRL1    0x0c9a
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG51_CTRL2    0x0c9b
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG51_CTRL3    0x0c9c
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG52_CTRL1    0x0c9d
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG52_CTRL2    0x0c9e
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG52_CTRL3    0x0c9f
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG53_CTRL1    0x0ca0
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG53_CTRL2    0x0ca1
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG53_CTRL3    0x0ca2
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG54_CTRL1    0x0ca3
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG54_CTRL2    0x0ca4
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG54_CTRL3    0x0ca5
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG55_CTRL1    0x0ca6
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG55_CTRL2    0x0ca7
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG55_CTRL3    0x0ca8
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG56_CTRL1    0x0ca9
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG56_CTRL2    0x0caa
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG56_CTRL3    0x0cab
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG57_CTRL1    0x0cac
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG57_CTRL2    0x0cad
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG57_CTRL3    0x0cae
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG58_CTRL1    0x0caf
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG58_CTRL2    0x0cb0
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG58_CTRL3    0x0cb1
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG59_CTRL1    0x0cb2
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG59_CTRL2    0x0cb3
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG59_CTRL3    0x0cb4
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG60_CTRL1    0x0cb5
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG60_CTRL2    0x0cb6
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG60_CTRL3    0x0cb7
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG61_CTRL1    0x0cb8
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG61_CTRL2    0x0cb9
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG61_CTRL3    0x0cba
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG62_CTRL1    0x0cbb
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG62_CTRL2    0x0cbc
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG62_CTRL3    0x0cbd
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG63_CTRL1    0x0cbe
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL1_VS_UNTAGSET_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL1_VS_UNTAGSET_MASK    0xFF00
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL1_VS_SMBR_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL1_VS_SMBR_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG63_CTRL2    0x0cbf
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL2_VS_FIDEN_OFFSET    7
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL2_VS_FIDEN_MASK    0x80
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL2_VS_SPRI_OFFSET    4
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL2_VS_SPRI_MASK    0x70
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL2_VS_FID_MSTI_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL2_VS_FID_MSTI_MASK    0xF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG63_CTRL3    0x0cc0
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL3_VS_EFID_OFFSET    13
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL3_VS_EFID_MASK    0xE000
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL3_VS_EFIDEN_OFFSET    12
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL3_VS_EFIDEN_MASK    0x1000
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL3_VS_SVID_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL3_VS_SVID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG0_CTRL4    0x0cc1
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG0_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG1_CTRL4    0x0cc2
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG1_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG2_CTRL4    0x0cc3
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG2_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG3_CTRL4    0x0cc4
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG3_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG4_CTRL4    0x0cc5
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG4_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG5_CTRL4    0x0cc6
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG5_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG6_CTRL4    0x0cc7
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG6_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG7_CTRL4    0x0cc8
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG7_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG8_CTRL4    0x0cc9
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG8_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG9_CTRL4    0x0cca
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG9_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG10_CTRL4    0x0ccb
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG10_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG11_CTRL4    0x0ccc
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG11_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG12_CTRL4    0x0ccd
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG12_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG13_CTRL4    0x0cce
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG13_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG14_CTRL4    0x0ccf
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG14_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG15_CTRL4    0x0cd0
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG15_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG16_CTRL4    0x0cd1
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG16_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG17_CTRL4    0x0cd2
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG17_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG18_CTRL4    0x0cd3
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG18_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG19_CTRL4    0x0cd4
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG19_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG20_CTRL4    0x0cd5
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG20_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG21_CTRL4    0x0cd6
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG21_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG22_CTRL4    0x0cd7
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG22_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG23_CTRL4    0x0cd8
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG23_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG24_CTRL4    0x0cd9
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG24_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG25_CTRL4    0x0cda
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG25_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG26_CTRL4    0x0cdb
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG26_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG27_CTRL4    0x0cdc
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG27_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG28_CTRL4    0x0cdd
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG28_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG29_CTRL4    0x0cde
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG29_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG30_CTRL4    0x0cdf
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG30_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG31_CTRL4    0x0ce0
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG31_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG32_CTRL4    0x0ce1
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG32_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG33_CTRL4    0x0ce2
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG33_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG34_CTRL4    0x0ce3
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG34_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG35_CTRL4    0x0ce4
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG35_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG36_CTRL4    0x0ce5
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG36_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG37_CTRL4    0x0ce6
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG37_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG38_CTRL4    0x0ce7
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG38_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG39_CTRL4    0x0ce8
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG39_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG40_CTRL4    0x0ce9
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG40_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG41_CTRL4    0x0cea
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG41_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG42_CTRL4    0x0ceb
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG42_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG43_CTRL4    0x0cec
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG43_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG44_CTRL4    0x0ced
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG44_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG45_CTRL4    0x0cee
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG45_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG46_CTRL4    0x0cef
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG46_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG47_CTRL4    0x0cf0
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG47_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG48_CTRL4    0x0cf1
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG48_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG49_CTRL4    0x0cf2
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG49_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG50_CTRL4    0x0cf3
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG50_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG51_CTRL4    0x0cf4
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG51_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG52_CTRL4    0x0cf5
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG52_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG53_CTRL4    0x0cf6
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG53_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG54_CTRL4    0x0cf7
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG54_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG55_CTRL4    0x0cf8
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG55_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG56_CTRL4    0x0cf9
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG56_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG57_CTRL4    0x0cfa
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG57_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG58_CTRL4    0x0cfb
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG58_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG59_CTRL4    0x0cfc
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG59_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG60_CTRL4    0x0cfd
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG60_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG61_CTRL4    0x0cfe
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG61_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG62_CTRL4    0x0cff
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG62_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_C2SCFG0_CTRL0    0x0d00
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG0_CTRL1    0x0d01
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG0_CTRL2    0x0d02
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG0_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG1_CTRL0    0x0d03
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG1_CTRL1    0x0d04
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG1_CTRL2    0x0d05
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG1_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG2_CTRL0    0x0d06
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG2_CTRL1    0x0d07
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG2_CTRL2    0x0d08
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG2_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG3_CTRL0    0x0d09
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG3_CTRL1    0x0d0a
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG3_CTRL2    0x0d0b
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG3_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG4_CTRL0    0x0d0c
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG4_CTRL1    0x0d0d
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG4_CTRL2    0x0d0e
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG4_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG5_CTRL0    0x0d0f
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG5_CTRL1    0x0d10
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG5_CTRL2    0x0d11
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG5_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG6_CTRL0    0x0d12
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG6_CTRL1    0x0d13
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG6_CTRL2    0x0d14
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG6_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG7_CTRL0    0x0d15
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG7_CTRL1    0x0d16
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG7_CTRL2    0x0d17
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG7_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG8_CTRL0    0x0d18
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG8_CTRL1    0x0d19
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG8_CTRL2    0x0d1a
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG8_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG9_CTRL0    0x0d1b
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG9_CTRL1    0x0d1c
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG9_CTRL2    0x0d1d
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG9_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG10_CTRL0    0x0d1e
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG10_CTRL1    0x0d1f
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG10_CTRL2    0x0d20
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG10_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG11_CTRL0    0x0d21
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG11_CTRL1    0x0d22
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG11_CTRL2    0x0d23
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG11_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG12_CTRL0    0x0d24
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG12_CTRL1    0x0d25
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG12_CTRL2    0x0d26
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG12_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG13_CTRL0    0x0d27
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG13_CTRL1    0x0d28
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG13_CTRL2    0x0d29
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG13_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG14_CTRL0    0x0d2a
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG14_CTRL1    0x0d2b
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG14_CTRL2    0x0d2c
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG14_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG15_CTRL0    0x0d2d
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG15_CTRL1    0x0d2e
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG15_CTRL2    0x0d2f
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG15_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG16_CTRL0    0x0d30
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG16_CTRL1    0x0d31
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG16_CTRL2    0x0d32
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG16_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG17_CTRL0    0x0d33
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG17_CTRL1    0x0d34
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG17_CTRL2    0x0d35
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG17_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG18_CTRL0    0x0d36
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG18_CTRL1    0x0d37
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG18_CTRL2    0x0d38
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG18_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG19_CTRL0    0x0d39
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG19_CTRL1    0x0d3a
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG19_CTRL2    0x0d3b
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG19_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG20_CTRL0    0x0d3c
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG20_CTRL1    0x0d3d
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG20_CTRL2    0x0d3e
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG20_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG21_CTRL0    0x0d3f
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG21_CTRL1    0x0d40
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG21_CTRL2    0x0d41
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG21_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG22_CTRL0    0x0d42
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG22_CTRL1    0x0d43
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG22_CTRL2    0x0d44
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG22_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG23_CTRL0    0x0d45
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG23_CTRL1    0x0d46
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG23_CTRL2    0x0d47
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG23_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG24_CTRL0    0x0d48
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG24_CTRL1    0x0d49
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG24_CTRL2    0x0d4a
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG24_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG25_CTRL0    0x0d4b
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG25_CTRL1    0x0d4c
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG25_CTRL2    0x0d4d
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG25_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG26_CTRL0    0x0d4e
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG26_CTRL1    0x0d4f
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG26_CTRL2    0x0d50
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG26_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG27_CTRL0    0x0d51
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG27_CTRL1    0x0d52
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG27_CTRL2    0x0d53
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG27_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG28_CTRL0    0x0d54
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG28_CTRL1    0x0d55
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG28_CTRL2    0x0d56
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG28_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG29_CTRL0    0x0d57
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG29_CTRL1    0x0d58
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG29_CTRL2    0x0d59
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG29_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG30_CTRL0    0x0d5a
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG30_CTRL1    0x0d5b
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG30_CTRL2    0x0d5c
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG30_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG31_CTRL0    0x0d5d
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG31_CTRL1    0x0d5e
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG31_CTRL2    0x0d5f
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG31_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG32_CTRL0    0x0d60
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG32_CTRL1    0x0d61
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG32_CTRL2    0x0d62
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG32_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG33_CTRL0    0x0d63
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG33_CTRL1    0x0d64
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG33_CTRL2    0x0d65
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG33_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG34_CTRL0    0x0d66
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG34_CTRL1    0x0d67
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG34_CTRL2    0x0d68
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG34_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG35_CTRL0    0x0d69
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG35_CTRL1    0x0d6a
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG35_CTRL2    0x0d6b
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG35_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG36_CTRL0    0x0d6c
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG36_CTRL1    0x0d6d
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG36_CTRL2    0x0d6e
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG36_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG37_CTRL0    0x0d6f
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG37_CTRL1    0x0d70
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG37_CTRL2    0x0d71
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG37_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG38_CTRL0    0x0d72
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG38_CTRL1    0x0d73
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG38_CTRL2    0x0d74
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG38_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG39_CTRL0    0x0d75
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG39_CTRL1    0x0d76
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG39_CTRL2    0x0d77
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG39_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG40_CTRL0    0x0d78
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG40_CTRL1    0x0d79
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG40_CTRL2    0x0d7a
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG40_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG41_CTRL0    0x0d7b
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG41_CTRL1    0x0d7c
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG41_CTRL2    0x0d7d
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG41_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG42_CTRL0    0x0d7e
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG42_CTRL1    0x0d7f
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG42_CTRL2    0x0d80
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG42_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG43_CTRL0    0x0d81
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG43_CTRL1    0x0d82
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG43_CTRL2    0x0d83
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG43_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG44_CTRL0    0x0d84
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG44_CTRL1    0x0d85
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG44_CTRL2    0x0d86
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG44_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG45_CTRL0    0x0d87
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG45_CTRL1    0x0d88
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG45_CTRL2    0x0d89
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG45_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG46_CTRL0    0x0d8a
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG46_CTRL1    0x0d8b
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG46_CTRL2    0x0d8c
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG46_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG47_CTRL0    0x0d8d
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG47_CTRL1    0x0d8e
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG47_CTRL2    0x0d8f
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG47_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG48_CTRL0    0x0d90
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG48_CTRL1    0x0d91
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG48_CTRL2    0x0d92
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG48_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG49_CTRL0    0x0d93
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG49_CTRL1    0x0d94
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG49_CTRL2    0x0d95
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG49_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG50_CTRL0    0x0d96
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG50_CTRL1    0x0d97
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG50_CTRL2    0x0d98
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG50_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG51_CTRL0    0x0d99
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG51_CTRL1    0x0d9a
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG51_CTRL2    0x0d9b
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG51_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG52_CTRL0    0x0d9c
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG52_CTRL1    0x0d9d
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG52_CTRL2    0x0d9e
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG52_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG53_CTRL0    0x0d9f
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG53_CTRL1    0x0da0
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG53_CTRL2    0x0da1
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG53_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG54_CTRL0    0x0da2
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG54_CTRL1    0x0da3
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG54_CTRL2    0x0da4
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG54_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG55_CTRL0    0x0da5
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG55_CTRL1    0x0da6
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG55_CTRL2    0x0da7
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG55_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG56_CTRL0    0x0da8
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG56_CTRL1    0x0da9
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG56_CTRL2    0x0daa
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG56_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG57_CTRL0    0x0dab
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG57_CTRL1    0x0dac
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG57_CTRL2    0x0dad
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG57_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG58_CTRL0    0x0dae
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG58_CTRL1    0x0daf
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG58_CTRL2    0x0db0
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG58_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG59_CTRL0    0x0db1
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG59_CTRL1    0x0db2
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG59_CTRL2    0x0db3
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG59_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG60_CTRL0    0x0db4
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG60_CTRL1    0x0db5
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG60_CTRL2    0x0db6
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG60_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG61_CTRL0    0x0db7
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG61_CTRL1    0x0db8
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG61_CTRL2    0x0db9
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG61_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG62_CTRL0    0x0dba
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG62_CTRL1    0x0dbb
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG62_CTRL2    0x0dbc
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG62_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG63_CTRL0    0x0dbd
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG63_CTRL1    0x0dbe
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG63_CTRL2    0x0dbf
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG63_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG64_CTRL0    0x0dc0
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG64_CTRL1    0x0dc1
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG64_CTRL2    0x0dc2
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG64_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG65_CTRL0    0x0dc3
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG65_CTRL1    0x0dc4
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG65_CTRL2    0x0dc5
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG65_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG66_CTRL0    0x0dc6
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG66_CTRL1    0x0dc7
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG66_CTRL2    0x0dc8
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG66_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG67_CTRL0    0x0dc9
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG67_CTRL1    0x0dca
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG67_CTRL2    0x0dcb
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG67_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG68_CTRL0    0x0dcc
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG68_CTRL1    0x0dcd
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG68_CTRL2    0x0dce
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG68_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG69_CTRL0    0x0dcf
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG69_CTRL1    0x0dd0
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG69_CTRL2    0x0dd1
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG69_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG70_CTRL0    0x0dd2
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG70_CTRL1    0x0dd3
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG70_CTRL2    0x0dd4
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG70_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG71_CTRL0    0x0dd5
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG71_CTRL1    0x0dd6
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG71_CTRL2    0x0dd7
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG71_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG72_CTRL0    0x0dd8
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG72_CTRL1    0x0dd9
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG72_CTRL2    0x0dda
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG72_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG73_CTRL0    0x0ddb
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG73_CTRL1    0x0ddc
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG73_CTRL2    0x0ddd
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG73_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG74_CTRL0    0x0dde
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG74_CTRL1    0x0ddf
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG74_CTRL2    0x0de0
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG74_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG75_CTRL0    0x0de1
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG75_CTRL1    0x0de2
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG75_CTRL2    0x0de3
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG75_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG76_CTRL0    0x0de4
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG76_CTRL1    0x0de5
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG76_CTRL2    0x0de6
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG76_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG77_CTRL0    0x0de7
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG77_CTRL1    0x0de8
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG77_CTRL2    0x0de9
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG77_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG78_CTRL0    0x0dea
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG78_CTRL1    0x0deb
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG78_CTRL2    0x0dec
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG78_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG79_CTRL0    0x0ded
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG79_CTRL1    0x0dee
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG79_CTRL2    0x0def
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG79_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG80_CTRL0    0x0df0
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG80_CTRL1    0x0df1
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG80_CTRL2    0x0df2
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG80_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG81_CTRL0    0x0df3
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG81_CTRL1    0x0df4
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG81_CTRL2    0x0df5
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG81_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG82_CTRL0    0x0df6
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG82_CTRL1    0x0df7
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG82_CTRL2    0x0df8
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG82_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG83_CTRL0    0x0df9
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG83_CTRL1    0x0dfa
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG83_CTRL2    0x0dfb
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG83_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG84_CTRL0    0x0dfc
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG84_CTRL1    0x0dfd
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG84_CTRL2    0x0dfe
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG84_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG85_CTRL0    0x0dff
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG85_CTRL1    0x0e00
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG85_CTRL2    0x0e01
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG85_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG86_CTRL0    0x0e02
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG86_CTRL1    0x0e03
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG86_CTRL2    0x0e04
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG86_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG87_CTRL0    0x0e05
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG87_CTRL1    0x0e06
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG87_CTRL2    0x0e07
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG87_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG88_CTRL0    0x0e08
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG88_CTRL1    0x0e09
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG88_CTRL2    0x0e0a
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG88_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG89_CTRL0    0x0e0b
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG89_CTRL1    0x0e0c
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG89_CTRL2    0x0e0d
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG89_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG90_CTRL0    0x0e0e
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG90_CTRL1    0x0e0f
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG90_CTRL2    0x0e10
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG90_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG91_CTRL0    0x0e11
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG91_CTRL1    0x0e12
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG91_CTRL2    0x0e13
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG91_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG92_CTRL0    0x0e14
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG92_CTRL1    0x0e15
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG92_CTRL2    0x0e16
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG92_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG93_CTRL0    0x0e17
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG93_CTRL1    0x0e18
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG93_CTRL2    0x0e19
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG93_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG94_CTRL0    0x0e1a
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG94_CTRL1    0x0e1b
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG94_CTRL2    0x0e1c
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG94_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG95_CTRL0    0x0e1d
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG95_CTRL1    0x0e1e
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG95_CTRL2    0x0e1f
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG95_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG96_CTRL0    0x0e20
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG96_CTRL1    0x0e21
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG96_CTRL2    0x0e22
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG96_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG97_CTRL0    0x0e23
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG97_CTRL1    0x0e24
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG97_CTRL2    0x0e25
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG97_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG98_CTRL0    0x0e26
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG98_CTRL1    0x0e27
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG98_CTRL2    0x0e28
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG98_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG99_CTRL0    0x0e29
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG99_CTRL1    0x0e2a
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG99_CTRL2    0x0e2b
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG99_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG100_CTRL0    0x0e2c
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG100_CTRL1    0x0e2d
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG100_CTRL2    0x0e2e
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG100_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG101_CTRL0    0x0e2f
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG101_CTRL1    0x0e30
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG101_CTRL2    0x0e31
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG101_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG102_CTRL0    0x0e32
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG102_CTRL1    0x0e33
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG102_CTRL2    0x0e34
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG102_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG103_CTRL0    0x0e35
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG103_CTRL1    0x0e36
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG103_CTRL2    0x0e37
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG103_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG104_CTRL0    0x0e38
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG104_CTRL1    0x0e39
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG104_CTRL2    0x0e3a
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG104_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG105_CTRL0    0x0e3b
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG105_CTRL1    0x0e3c
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG105_CTRL2    0x0e3d
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG105_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG106_CTRL0    0x0e3e
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG106_CTRL1    0x0e3f
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG106_CTRL2    0x0e40
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG106_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG107_CTRL0    0x0e41
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG107_CTRL1    0x0e42
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG107_CTRL2    0x0e43
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG107_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG108_CTRL0    0x0e44
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG108_CTRL1    0x0e45
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG108_CTRL2    0x0e46
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG108_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG109_CTRL0    0x0e47
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG109_CTRL1    0x0e48
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG109_CTRL2    0x0e49
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG109_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG110_CTRL0    0x0e4a
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG110_CTRL1    0x0e4b
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG110_CTRL2    0x0e4c
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG110_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG111_CTRL0    0x0e4d
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG111_CTRL1    0x0e4e
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG111_CTRL2    0x0e4f
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG111_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG112_CTRL0    0x0e50
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG112_CTRL1    0x0e51
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG112_CTRL2    0x0e52
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG112_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG113_CTRL0    0x0e53
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG113_CTRL1    0x0e54
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG113_CTRL2    0x0e55
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG113_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG114_CTRL0    0x0e56
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG114_CTRL1    0x0e57
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG114_CTRL2    0x0e58
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG114_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG115_CTRL0    0x0e59
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG115_CTRL1    0x0e5a
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG115_CTRL2    0x0e5b
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG115_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG116_CTRL0    0x0e5c
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG116_CTRL1    0x0e5d
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG116_CTRL2    0x0e5e
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG116_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG117_CTRL0    0x0e5f
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG117_CTRL1    0x0e60
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG117_CTRL2    0x0e61
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG117_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG118_CTRL0    0x0e62
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG118_CTRL1    0x0e63
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG118_CTRL2    0x0e64
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG118_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG119_CTRL0    0x0e65
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG119_CTRL1    0x0e66
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG119_CTRL2    0x0e67
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG119_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG120_CTRL0    0x0e68
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG120_CTRL1    0x0e69
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG120_CTRL2    0x0e6a
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG120_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG121_CTRL0    0x0e6b
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG121_CTRL1    0x0e6c
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG121_CTRL2    0x0e6d
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG121_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG122_CTRL0    0x0e6e
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG122_CTRL1    0x0e6f
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG122_CTRL2    0x0e70
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG122_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG123_CTRL0    0x0e71
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG123_CTRL1    0x0e72
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG123_CTRL2    0x0e73
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG123_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG124_CTRL0    0x0e74
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG124_CTRL1    0x0e75
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG124_CTRL2    0x0e76
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG124_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG125_CTRL0    0x0e77
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG125_CTRL1    0x0e78
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG125_CTRL2    0x0e79
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG125_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG126_CTRL0    0x0e7a
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG126_CTRL1    0x0e7b
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG126_CTRL2    0x0e7c
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG126_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG127_CTRL0    0x0e7d
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL0_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL0_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_C2SCFG127_CTRL1    0x0e7e
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL1_C2SENPMSK_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL1_C2SENPMSK_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL1_C2SENPMSK_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL1_C2SENPMSK_MASK    0xFF
-
-#define    RTL8367C_REG_SVLAN_C2SCFG127_CTRL2    0x0e7f
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL2_OFFSET    0
-#define    RTL8367C_SVLAN_C2SCFG127_CTRL2_MASK    0x1FFF
-
-#define    RTL8367C_REG_SVLAN_CFG    0x0e80
-#define    RTL8367C_VS_PORT7_DMACVIDSEL_OFFSET    14
-#define    RTL8367C_VS_PORT7_DMACVIDSEL_MASK    0x4000
-#define    RTL8367C_VS_PORT6_DMACVIDSEL_OFFSET    13
-#define    RTL8367C_VS_PORT6_DMACVIDSEL_MASK    0x2000
-#define    RTL8367C_VS_PORT5_DMACVIDSEL_OFFSET    12
-#define    RTL8367C_VS_PORT5_DMACVIDSEL_MASK    0x1000
-#define    RTL8367C_VS_PORT4_DMACVIDSEL_OFFSET    11
-#define    RTL8367C_VS_PORT4_DMACVIDSEL_MASK    0x800
-#define    RTL8367C_VS_PORT3_DMACVIDSEL_OFFSET    10
-#define    RTL8367C_VS_PORT3_DMACVIDSEL_MASK    0x400
-#define    RTL8367C_VS_PORT2_DMACVIDSEL_OFFSET    9
-#define    RTL8367C_VS_PORT2_DMACVIDSEL_MASK    0x200
-#define    RTL8367C_VS_PORT1_DMACVIDSEL_OFFSET    8
-#define    RTL8367C_VS_PORT1_DMACVIDSEL_MASK    0x100
-#define    RTL8367C_VS_PORT0_DMACVIDSEL_OFFSET    7
-#define    RTL8367C_VS_PORT0_DMACVIDSEL_MASK    0x80
-#define    RTL8367C_VS_UIFSEG_OFFSET    6
-#define    RTL8367C_VS_UIFSEG_MASK    0x40
-#define    RTL8367C_VS_UNMAT_OFFSET    4
-#define    RTL8367C_VS_UNMAT_MASK    0x30
-#define    RTL8367C_VS_UNTAG_OFFSET    2
-#define    RTL8367C_VS_UNTAG_MASK    0xC
-#define    RTL8367C_VS_SPRISEL_OFFSET    0
-#define    RTL8367C_VS_SPRISEL_MASK    0x3
-
-#define    RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL0    0x0e81
-#define    RTL8367C_VS_PORT1_SVIDX_OFFSET    8
-#define    RTL8367C_VS_PORT1_SVIDX_MASK    0x3F00
-#define    RTL8367C_VS_PORT0_SVIDX_OFFSET    0
-#define    RTL8367C_VS_PORT0_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL1    0x0e82
-#define    RTL8367C_VS_PORT3_SVIDX_OFFSET    8
-#define    RTL8367C_VS_PORT3_SVIDX_MASK    0x3F00
-#define    RTL8367C_VS_PORT2_SVIDX_OFFSET    0
-#define    RTL8367C_VS_PORT2_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL2    0x0e83
-#define    RTL8367C_VS_PORT5_SVIDX_OFFSET    8
-#define    RTL8367C_VS_PORT5_SVIDX_MASK    0x3F00
-#define    RTL8367C_VS_PORT4_SVIDX_OFFSET    0
-#define    RTL8367C_VS_PORT4_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL3    0x0e84
-#define    RTL8367C_VS_PORT7_SVIDX_OFFSET    8
-#define    RTL8367C_VS_PORT7_SVIDX_MASK    0x3F00
-#define    RTL8367C_VS_PORT6_SVIDX_OFFSET    0
-#define    RTL8367C_VS_PORT6_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_UNTAG_UNMAT_CFG    0x0e85
-#define    RTL8367C_VS_UNTAG_SVIDX_OFFSET    8
-#define    RTL8367C_VS_UNTAG_SVIDX_MASK    0x3F00
-#define    RTL8367C_VS_UNMAT_SVIDX_OFFSET    0
-#define    RTL8367C_VS_UNMAT_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_LOOKUP_TYPE    0x0e86
-#define    RTL8367C_SVLAN_LOOKUP_TYPE_OFFSET    0
-#define    RTL8367C_SVLAN_LOOKUP_TYPE_MASK    0x1
-
-#define    RTL8367C_REG_IPMC_GROUP_VALID_15_0    0x0e87
-
-#define    RTL8367C_REG_IPMC_GROUP_VALID_31_16    0x0e88
-
-#define    RTL8367C_REG_IPMC_GROUP_VALID_47_32    0x0e89
-
-#define    RTL8367C_REG_IPMC_GROUP_VALID_63_48    0x0e8a
-
-#define    RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL4    0x0e8b
-#define    RTL8367C_VS_PORT9_SVIDX_OFFSET    8
-#define    RTL8367C_VS_PORT9_SVIDX_MASK    0x3F00
-#define    RTL8367C_VS_PORT8_SVIDX_OFFSET    0
-#define    RTL8367C_VS_PORT8_SVIDX_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL5    0x0e8c
-#define    RTL8367C_SVLAN_PORTBASED_SVIDX_CTRL5_OFFSET    0
-#define    RTL8367C_SVLAN_PORTBASED_SVIDX_CTRL5_MASK    0x3F
-
-#define    RTL8367C_REG_SVLAN_CFG_EXT    0x0e8d
-#define    RTL8367C_VS_PORT10_DMACVIDSEL_OFFSET    2
-#define    RTL8367C_VS_PORT10_DMACVIDSEL_MASK    0x4
-#define    RTL8367C_VS_PORT9_DMACVIDSEL_OFFSET    1
-#define    RTL8367C_VS_PORT9_DMACVIDSEL_MASK    0x2
-#define    RTL8367C_VS_PORT8_DMACVIDSEL_OFFSET    0
-#define    RTL8367C_VS_PORT8_DMACVIDSEL_MASK    0x1
-
-#define    RTL8367C_REG_SVLAN_MEMBERCFG63_CTRL4    0x0e8e
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL4_VS_UNTAGSET_EXT_OFFSET    8
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL4_VS_UNTAGSET_EXT_MASK    0x700
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL4_VS_SMBR_EXT_OFFSET    0
-#define    RTL8367C_SVLAN_MEMBERCFG63_CTRL4_VS_SMBR_EXT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_DUMMY_0    0x0e90
-
-#define    RTL8367C_REG_SVLAN_DUMMY_1    0x0e91
-
-#define    RTL8367C_REG_SVLAN_DUMMY_2    0x0e92
-
-#define    RTL8367C_REG_SVLAN_DUMMY_3    0x0e93
-
-#define    RTL8367C_REG_SVLAN_DUMMY_4    0x0e94
-
-#define    RTL8367C_REG_SVLAN_DUMMY_5    0x0e95
-
-#define    RTL8367C_REG_SVLAN_DUMMY_6    0x0e96
-
-#define    RTL8367C_REG_SVLAN_DUMMY_7    0x0e97
-
-#define    RTL8367C_REG_SVLAN_DUMMY_8    0x0e98
-
-#define    RTL8367C_REG_SVLAN_DUMMY_9    0x0e99
-
-#define    RTL8367C_REG_SVLAN_DUMMY_10    0x0e9a
-
-#define    RTL8367C_REG_SVLAN_DUMMY_11    0x0e9b
-
-#define    RTL8367C_REG_SVLAN_DUMMY_12    0x0e9c
-
-#define    RTL8367C_REG_SVLAN_DUMMY_13    0x0e9d
-
-#define    RTL8367C_REG_SVLAN_DUMMY_14    0x0e9e
-
-#define    RTL8367C_REG_SVLAN_DUMMY_15    0x0e9f
-
-#define    RTL8367C_REG_SVLAN_DUMMY_16    0x0ea0
-
-#define    RTL8367C_REG_SVLAN_DUMMY_17    0x0ea1
-
-#define    RTL8367C_REG_SVLAN_DUMMY_18    0x0ea2
-
-#define    RTL8367C_REG_SVLAN_DUMMY_19    0x0ea3
-
-#define    RTL8367C_REG_SVLAN_DUMMY_20    0x0ea4
-
-#define    RTL8367C_REG_SVLAN_DUMMY_21    0x0ea5
-
-#define    RTL8367C_REG_SVLAN_DUMMY_22    0x0ea6
-
-#define    RTL8367C_REG_SVLAN_DUMMY_23    0x0ea7
-
-#define    RTL8367C_REG_SVLAN_DUMMY_24    0x0ea8
-
-#define    RTL8367C_REG_SVLAN_DUMMY_25    0x0ea9
-
-#define    RTL8367C_REG_SVLAN_DUMMY_26    0x0eaa
-
-#define    RTL8367C_REG_SVLAN_DUMMY_27    0x0eab
-
-#define    RTL8367C_REG_SVLAN_DUMMY_28    0x0eac
-
-#define    RTL8367C_REG_SVLAN_DUMMY_29    0x0ead
-
-#define    RTL8367C_REG_SVLAN_DUMMY_30    0x0eae
-
-#define    RTL8367C_REG_SVLAN_DUMMY_31    0x0eaf
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_00    0x0eb0
-#define    RTL8367C_IPMC_GROUP_VID_00_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_00_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_01    0x0eb1
-#define    RTL8367C_IPMC_GROUP_VID_01_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_01_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_02    0x0eb2
-#define    RTL8367C_IPMC_GROUP_VID_02_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_02_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_03    0x0eb3
-#define    RTL8367C_IPMC_GROUP_VID_03_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_03_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_04    0x0eb4
-#define    RTL8367C_IPMC_GROUP_VID_04_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_04_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_05    0x0eb5
-#define    RTL8367C_IPMC_GROUP_VID_05_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_05_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_06    0x0eb6
-#define    RTL8367C_IPMC_GROUP_VID_06_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_06_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_07    0x0eb7
-#define    RTL8367C_IPMC_GROUP_VID_07_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_07_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_08    0x0eb8
-#define    RTL8367C_IPMC_GROUP_VID_08_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_08_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_09    0x0eb9
-#define    RTL8367C_IPMC_GROUP_VID_09_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_09_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_10    0x0eba
-#define    RTL8367C_IPMC_GROUP_VID_10_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_10_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_11    0x0ebb
-#define    RTL8367C_IPMC_GROUP_VID_11_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_11_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_12    0x0ebc
-#define    RTL8367C_IPMC_GROUP_VID_12_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_12_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_13    0x0ebd
-#define    RTL8367C_IPMC_GROUP_VID_13_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_13_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_14    0x0ebe
-#define    RTL8367C_IPMC_GROUP_VID_14_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_14_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_15    0x0ebf
-#define    RTL8367C_IPMC_GROUP_VID_15_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_15_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_16    0x0ec0
-#define    RTL8367C_IPMC_GROUP_VID_16_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_16_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_17    0x0ec1
-#define    RTL8367C_IPMC_GROUP_VID_17_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_17_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_18    0x0ec2
-#define    RTL8367C_IPMC_GROUP_VID_18_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_18_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_19    0x0ec3
-#define    RTL8367C_IPMC_GROUP_VID_19_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_19_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_20    0x0ec4
-#define    RTL8367C_IPMC_GROUP_VID_20_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_20_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_21    0x0ec5
-#define    RTL8367C_IPMC_GROUP_VID_21_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_21_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_22    0x0ec6
-#define    RTL8367C_IPMC_GROUP_VID_22_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_22_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_23    0x0ec7
-#define    RTL8367C_IPMC_GROUP_VID_23_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_23_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_24    0x0ec8
-#define    RTL8367C_IPMC_GROUP_VID_24_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_24_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_25    0x0ec9
-#define    RTL8367C_IPMC_GROUP_VID_25_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_25_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_26    0x0eca
-#define    RTL8367C_IPMC_GROUP_VID_26_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_26_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_27    0x0ecb
-#define    RTL8367C_IPMC_GROUP_VID_27_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_27_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_28    0x0ecc
-#define    RTL8367C_IPMC_GROUP_VID_28_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_28_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_29    0x0ecd
-#define    RTL8367C_IPMC_GROUP_VID_29_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_29_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_30    0x0ece
-#define    RTL8367C_IPMC_GROUP_VID_30_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_30_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_31    0x0ecf
-#define    RTL8367C_IPMC_GROUP_VID_31_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_31_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_32    0x0ed0
-#define    RTL8367C_IPMC_GROUP_VID_32_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_32_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_33    0x0ed1
-#define    RTL8367C_IPMC_GROUP_VID_33_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_33_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_34    0x0ed2
-#define    RTL8367C_IPMC_GROUP_VID_34_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_34_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_35    0x0ed3
-#define    RTL8367C_IPMC_GROUP_VID_35_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_35_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_36    0x0ed4
-#define    RTL8367C_IPMC_GROUP_VID_36_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_36_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_37    0x0ed5
-#define    RTL8367C_IPMC_GROUP_VID_37_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_37_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_38    0x0ed6
-#define    RTL8367C_IPMC_GROUP_VID_38_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_38_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_39    0x0ed7
-#define    RTL8367C_IPMC_GROUP_VID_39_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_39_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_40    0x0ed8
-#define    RTL8367C_IPMC_GROUP_VID_40_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_40_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_41    0x0ed9
-#define    RTL8367C_IPMC_GROUP_VID_41_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_41_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_42    0x0eda
-#define    RTL8367C_IPMC_GROUP_VID_42_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_42_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_43    0x0edb
-#define    RTL8367C_IPMC_GROUP_VID_43_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_43_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_44    0x0edc
-#define    RTL8367C_IPMC_GROUP_VID_44_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_44_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_45    0x0edd
-#define    RTL8367C_IPMC_GROUP_VID_45_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_45_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_46    0x0ede
-#define    RTL8367C_IPMC_GROUP_VID_46_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_46_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_47    0x0edf
-#define    RTL8367C_IPMC_GROUP_VID_47_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_47_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_48    0x0ef0
-#define    RTL8367C_IPMC_GROUP_VID_48_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_48_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_49    0x0ef1
-#define    RTL8367C_IPMC_GROUP_VID_49_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_49_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_50    0x0ef2
-#define    RTL8367C_IPMC_GROUP_VID_50_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_50_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_51    0x0ef3
-#define    RTL8367C_IPMC_GROUP_VID_51_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_51_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_52    0x0ef4
-#define    RTL8367C_IPMC_GROUP_VID_52_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_52_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_53    0x0ef5
-#define    RTL8367C_IPMC_GROUP_VID_53_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_53_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_54    0x0ef6
-#define    RTL8367C_IPMC_GROUP_VID_54_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_54_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_55    0x0ef7
-#define    RTL8367C_IPMC_GROUP_VID_55_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_55_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_56    0x0ef8
-#define    RTL8367C_IPMC_GROUP_VID_56_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_56_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_57    0x0ef9
-#define    RTL8367C_IPMC_GROUP_VID_57_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_57_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_58    0x0efa
-#define    RTL8367C_IPMC_GROUP_VID_58_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_58_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_59    0x0efb
-#define    RTL8367C_IPMC_GROUP_VID_59_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_59_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_60    0x0efc
-#define    RTL8367C_IPMC_GROUP_VID_60_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_60_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_61    0x0efd
-#define    RTL8367C_IPMC_GROUP_VID_61_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_61_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_62    0x0efe
-#define    RTL8367C_IPMC_GROUP_VID_62_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_62_MASK    0xFFF
-
-#define    RTL8367C_REG_IPMC_GROUP_VID_63    0x0eff
-#define    RTL8367C_IPMC_GROUP_VID_63_OFFSET    0
-#define    RTL8367C_IPMC_GROUP_VID_63_MASK    0xFFF
-
-/* (16'h0f00)hsactrl_reg */
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY0_CTRL0    0x0f00
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY0_CTRL1    0x0f01
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY0_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY1_CTRL0    0x0f02
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY1_CTRL1    0x0f03
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY1_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY2_CTRL0    0x0f04
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY2_CTRL1    0x0f05
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY2_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY3_CTRL0    0x0f06
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY3_CTRL1    0x0f07
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY3_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY4_CTRL0    0x0f08
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY4_CTRL1    0x0f09
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY4_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY5_CTRL0    0x0f0a
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY5_CTRL1    0x0f0b
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY5_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY6_CTRL0    0x0f0c
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY6_CTRL1    0x0f0d
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY6_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY7_CTRL0    0x0f0e
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY7_CTRL1    0x0f0f
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY7_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY8_CTRL0    0x0f10
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY8_CTRL1    0x0f11
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY8_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY9_CTRL0    0x0f12
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY9_CTRL1    0x0f13
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY9_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY10_CTRL0    0x0f14
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY10_CTRL1    0x0f15
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY10_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY11_CTRL0    0x0f16
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY11_CTRL1    0x0f17
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY11_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY12_CTRL0    0x0f18
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY12_CTRL1    0x0f19
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY12_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY13_CTRL0    0x0f1a
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY13_CTRL1    0x0f1b
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY13_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY14_CTRL0    0x0f1c
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY14_CTRL1    0x0f1d
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY14_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY15_CTRL0    0x0f1e
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY15_CTRL1    0x0f1f
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY15_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY16_CTRL0    0x0f20
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY16_CTRL1    0x0f21
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY16_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY17_CTRL0    0x0f22
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY17_CTRL1    0x0f23
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY17_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY18_CTRL0    0x0f24
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY18_CTRL1    0x0f25
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY18_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY19_CTRL0    0x0f26
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY19_CTRL1    0x0f27
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY19_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY20_CTRL0    0x0f28
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY20_CTRL1    0x0f29
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY20_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY21_CTRL0    0x0f2a
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY21_CTRL1    0x0f2b
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY21_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY22_CTRL0    0x0f2c
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY22_CTRL1    0x0f2d
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY22_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY23_CTRL0    0x0f2e
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY23_CTRL1    0x0f2f
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY23_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY24_CTRL0    0x0f30
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY24_CTRL1    0x0f31
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY24_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY25_CTRL0    0x0f32
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY25_CTRL1    0x0f33
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY25_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY26_CTRL0    0x0f34
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY26_CTRL1    0x0f35
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY26_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY27_CTRL0    0x0f36
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY27_CTRL1    0x0f37
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY27_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY28_CTRL0    0x0f38
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY28_CTRL1    0x0f39
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY28_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY29_CTRL0    0x0f3a
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY29_CTRL1    0x0f3b
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY29_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY30_CTRL0    0x0f3c
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY30_CTRL1    0x0f3d
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY30_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY31_CTRL0    0x0f3e
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY31_CTRL1    0x0f3f
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY31_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY32_CTRL0    0x0f40
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY32_CTRL1    0x0f41
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY32_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY33_CTRL0    0x0f42
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY33_CTRL1    0x0f43
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY33_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY34_CTRL0    0x0f44
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY34_CTRL1    0x0f45
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY34_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY35_CTRL0    0x0f46
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY35_CTRL1    0x0f47
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY35_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY36_CTRL0    0x0f48
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY36_CTRL1    0x0f49
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY36_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY37_CTRL0    0x0f4a
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY37_CTRL1    0x0f4b
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY37_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY38_CTRL0    0x0f4c
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY38_CTRL1    0x0f4d
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY38_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY39_CTRL0    0x0f4e
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY39_CTRL1    0x0f4f
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY39_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY40_CTRL0    0x0f50
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY40_CTRL1    0x0f51
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY40_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY41_CTRL0    0x0f52
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY41_CTRL1    0x0f53
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY41_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY42_CTRL0    0x0f54
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY42_CTRL1    0x0f55
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY42_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY43_CTRL0    0x0f56
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY43_CTRL1    0x0f57
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY43_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY44_CTRL0    0x0f58
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY44_CTRL1    0x0f59
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY44_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY45_CTRL0    0x0f5a
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY45_CTRL1    0x0f5b
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY45_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY46_CTRL0    0x0f5c
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY46_CTRL1    0x0f5d
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY46_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY47_CTRL0    0x0f5e
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY47_CTRL1    0x0f5f
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY47_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY48_CTRL0    0x0f60
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY48_CTRL1    0x0f61
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY48_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY49_CTRL0    0x0f62
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY49_CTRL1    0x0f63
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY49_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY50_CTRL0    0x0f64
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY50_CTRL1    0x0f65
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY50_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY51_CTRL0    0x0f66
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY51_CTRL1    0x0f67
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY51_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY52_CTRL0    0x0f68
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY52_CTRL1    0x0f69
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY52_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY53_CTRL0    0x0f6a
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY53_CTRL1    0x0f6b
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY53_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY54_CTRL0    0x0f6c
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY54_CTRL1    0x0f6d
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY54_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY55_CTRL0    0x0f6e
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY55_CTRL1    0x0f6f
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY55_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY56_CTRL0    0x0f70
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY56_CTRL1    0x0f71
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY56_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY57_CTRL0    0x0f72
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY57_CTRL1    0x0f73
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY57_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY58_CTRL0    0x0f74
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY58_CTRL1    0x0f75
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY58_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY59_CTRL0    0x0f76
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY59_CTRL1    0x0f77
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY59_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY60_CTRL0    0x0f78
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY60_CTRL1    0x0f79
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY60_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY61_CTRL0    0x0f7a
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY61_CTRL1    0x0f7b
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY61_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY62_CTRL0    0x0f7c
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY62_CTRL1    0x0f7d
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY62_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY63_CTRL0    0x0f7e
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY63_CTRL1    0x0f7f
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY63_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY64_CTRL0    0x0f80
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY64_CTRL1    0x0f81
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY64_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY65_CTRL0    0x0f82
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY65_CTRL1    0x0f83
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY65_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY66_CTRL0    0x0f84
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY66_CTRL1    0x0f85
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY66_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY67_CTRL0    0x0f86
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY67_CTRL1    0x0f87
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY67_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY68_CTRL0    0x0f88
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY68_CTRL1    0x0f89
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY68_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY69_CTRL0    0x0f8a
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY69_CTRL1    0x0f8b
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY69_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY70_CTRL0    0x0f8c
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY70_CTRL1    0x0f8d
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY70_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY71_CTRL0    0x0f8e
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY71_CTRL1    0x0f8f
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY71_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY72_CTRL0    0x0f90
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY72_CTRL1    0x0f91
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY72_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY73_CTRL0    0x0f92
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY73_CTRL1    0x0f93
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY73_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY74_CTRL0    0x0f94
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY74_CTRL1    0x0f95
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY74_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY75_CTRL0    0x0f96
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY75_CTRL1    0x0f97
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY75_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY76_CTRL0    0x0f98
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY76_CTRL1    0x0f99
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY76_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY77_CTRL0    0x0f9a
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY77_CTRL1    0x0f9b
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY77_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY78_CTRL0    0x0f9c
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY78_CTRL1    0x0f9d
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY78_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY79_CTRL0    0x0f9e
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY79_CTRL1    0x0f9f
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY79_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY80_CTRL0    0x0fa0
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY80_CTRL1    0x0fa1
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY80_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY81_CTRL0    0x0fa2
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY81_CTRL1    0x0fa3
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY81_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY82_CTRL0    0x0fa4
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY82_CTRL1    0x0fa5
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY82_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY83_CTRL0    0x0fa6
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY83_CTRL1    0x0fa7
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY83_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY84_CTRL0    0x0fa8
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY84_CTRL1    0x0fa9
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY84_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY85_CTRL0    0x0faa
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY85_CTRL1    0x0fab
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY85_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY86_CTRL0    0x0fac
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY86_CTRL1    0x0fad
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY86_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY87_CTRL0    0x0fae
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY87_CTRL1    0x0faf
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY87_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY88_CTRL0    0x0fb0
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY88_CTRL1    0x0fb1
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY88_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY89_CTRL0    0x0fb2
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY89_CTRL1    0x0fb3
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY89_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY90_CTRL0    0x0fb4
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY90_CTRL1    0x0fb5
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY90_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY91_CTRL0    0x0fb6
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY91_CTRL1    0x0fb7
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY91_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY92_CTRL0    0x0fb8
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY92_CTRL1    0x0fb9
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY92_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY93_CTRL0    0x0fba
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY93_CTRL1    0x0fbb
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY93_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY94_CTRL0    0x0fbc
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY94_CTRL1    0x0fbd
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY94_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY95_CTRL0    0x0fbe
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY95_CTRL1    0x0fbf
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY95_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY96_CTRL0    0x0fc0
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY96_CTRL1    0x0fc1
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY96_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY97_CTRL0    0x0fc2
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY97_CTRL1    0x0fc3
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY97_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY98_CTRL0    0x0fc4
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY98_CTRL1    0x0fc5
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY98_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY99_CTRL0    0x0fc6
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY99_CTRL1    0x0fc7
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY99_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY100_CTRL0    0x0fc8
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY100_CTRL1    0x0fc9
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY100_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY101_CTRL0    0x0fca
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY101_CTRL1    0x0fcb
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY101_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY102_CTRL0    0x0fcc
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY102_CTRL1    0x0fcd
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY102_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY103_CTRL0    0x0fce
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY103_CTRL1    0x0fcf
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY103_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY104_CTRL0    0x0fd0
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY104_CTRL1    0x0fd1
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY104_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY105_CTRL0    0x0fd2
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY105_CTRL1    0x0fd3
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY105_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY106_CTRL0    0x0fd4
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY106_CTRL1    0x0fd5
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY106_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY107_CTRL0    0x0fd6
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY107_CTRL1    0x0fd7
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY107_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY108_CTRL0    0x0fd8
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY108_CTRL1    0x0fd9
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY108_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY109_CTRL0    0x0fda
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY109_CTRL1    0x0fdb
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY109_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY110_CTRL0    0x0fdc
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY110_CTRL1    0x0fdd
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY110_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY111_CTRL0    0x0fde
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY111_CTRL1    0x0fdf
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY111_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY112_CTRL0    0x0fe0
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY112_CTRL1    0x0fe1
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY112_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY113_CTRL0    0x0fe2
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY113_CTRL1    0x0fe3
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY113_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY114_CTRL0    0x0fe4
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY114_CTRL1    0x0fe5
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY114_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY115_CTRL0    0x0fe6
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY115_CTRL1    0x0fe7
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY115_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY116_CTRL0    0x0fe8
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY116_CTRL1    0x0fe9
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY116_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY117_CTRL0    0x0fea
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY117_CTRL1    0x0feb
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY117_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY118_CTRL0    0x0fec
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY118_CTRL1    0x0fed
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY118_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY119_CTRL0    0x0fee
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY119_CTRL1    0x0fef
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY119_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY120_CTRL0    0x0ff0
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY120_CTRL1    0x0ff1
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY120_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY121_CTRL0    0x0ff2
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY121_CTRL1    0x0ff3
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY121_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY122_CTRL0    0x0ff4
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY122_CTRL1    0x0ff5
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY122_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY123_CTRL0    0x0ff6
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY123_CTRL1    0x0ff7
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY123_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY124_CTRL0    0x0ff8
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY124_CTRL1    0x0ff9
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY124_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY125_CTRL0    0x0ffa
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY125_CTRL1    0x0ffb
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY125_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY126_CTRL0    0x0ffc
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY126_CTRL1    0x0ffd
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY126_CTRL1_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY127_CTRL0    0x0ffe
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL0_DST_PORT1_OFFSET    9
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL0_DST_PORT1_MASK    0x200
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL0_SVIDX_OFFSET    3
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL0_SVIDX_MASK    0x1F8
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL0_DST_PORT_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL0_DST_PORT_MASK    0x7
-
-#define    RTL8367C_REG_SVLAN_SP2C_ENTRY127_CTRL1    0x0fff
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL1_VALID_OFFSET    12
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL1_VALID_MASK    0x1000
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL1_VID_OFFSET    0
-#define    RTL8367C_SVLAN_SP2C_ENTRY127_CTRL1_VID_MASK    0xFFF
-
-/* (16'h1000)mib_reg */
-
-#define    RTL8367C_REG_MIB_COUNTER0    0x1000
-
-#define    RTL8367C_REG_MIB_COUNTER1    0x1001
-
-#define    RTL8367C_REG_MIB_COUNTER2    0x1002
-
-#define    RTL8367C_REG_MIB_COUNTER3    0x1003
-
-#define    RTL8367C_REG_MIB_ADDRESS    0x1004
-#define    RTL8367C_MIB_ADDRESS_OFFSET    0
-#define    RTL8367C_MIB_ADDRESS_MASK    0x1FF
-
-#define    RTL8367C_REG_MIB_CTRL0    0x1005
-#define    RTL8367C_PORT10_RESET_OFFSET    15
-#define    RTL8367C_PORT10_RESET_MASK    0x8000
-#define    RTL8367C_PORT9_RESET_OFFSET    14
-#define    RTL8367C_PORT9_RESET_MASK    0x4000
-#define    RTL8367C_PORT8_RESET_OFFSET    13
-#define    RTL8367C_PORT8_RESET_MASK    0x2000
-#define    RTL8367C_RESET_VALUE_OFFSET    12
-#define    RTL8367C_RESET_VALUE_MASK    0x1000
-#define    RTL8367C_GLOBAL_RESET_OFFSET    11
-#define    RTL8367C_GLOBAL_RESET_MASK    0x800
-#define    RTL8367C_QM_RESET_OFFSET    10
-#define    RTL8367C_QM_RESET_MASK    0x400
-#define    RTL8367C_PORT7_RESET_OFFSET    9
-#define    RTL8367C_PORT7_RESET_MASK    0x200
-#define    RTL8367C_PORT6_RESET_OFFSET    8
-#define    RTL8367C_PORT6_RESET_MASK    0x100
-#define    RTL8367C_PORT5_RESET_OFFSET    7
-#define    RTL8367C_PORT5_RESET_MASK    0x80
-#define    RTL8367C_PORT4_RESET_OFFSET    6
-#define    RTL8367C_PORT4_RESET_MASK    0x40
-#define    RTL8367C_PORT3_RESET_OFFSET    5
-#define    RTL8367C_PORT3_RESET_MASK    0x20
-#define    RTL8367C_PORT2_RESET_OFFSET    4
-#define    RTL8367C_PORT2_RESET_MASK    0x10
-#define    RTL8367C_PORT1_RESET_OFFSET    3
-#define    RTL8367C_PORT1_RESET_MASK    0x8
-#define    RTL8367C_PORT0_RESET_OFFSET    2
-#define    RTL8367C_PORT0_RESET_MASK    0x4
-#define    RTL8367C_RESET_FLAG_OFFSET    1
-#define    RTL8367C_RESET_FLAG_MASK    0x2
-#define    RTL8367C_MIB_CTRL0_BUSY_FLAG_OFFSET    0
-#define    RTL8367C_MIB_CTRL0_BUSY_FLAG_MASK    0x1
-
-#define    RTL8367C_REG_MIB_CTRL1    0x1007
-#define    RTL8367C_COUNTER15_RESET_OFFSET    15
-#define    RTL8367C_COUNTER15_RESET_MASK    0x8000
-#define    RTL8367C_COUNTER14_RESET_OFFSET    14
-#define    RTL8367C_COUNTER14_RESET_MASK    0x4000
-#define    RTL8367C_COUNTER13_RESET_OFFSET    13
-#define    RTL8367C_COUNTER13_RESET_MASK    0x2000
-#define    RTL8367C_COUNTER12_RESET_OFFSET    12
-#define    RTL8367C_COUNTER12_RESET_MASK    0x1000
-#define    RTL8367C_COUNTER11_RESET_OFFSET    11
-#define    RTL8367C_COUNTER11_RESET_MASK    0x800
-#define    RTL8367C_COUNTER10_RESET_OFFSET    10
-#define    RTL8367C_COUNTER10_RESET_MASK    0x400
-#define    RTL8367C_COUNTER9_RESET_OFFSET    9
-#define    RTL8367C_COUNTER9_RESET_MASK    0x200
-#define    RTL8367C_COUNTER8_RESET_OFFSET    8
-#define    RTL8367C_COUNTER8_RESET_MASK    0x100
-#define    RTL8367C_COUNTER7_RESET_OFFSET    7
-#define    RTL8367C_COUNTER7_RESET_MASK    0x80
-#define    RTL8367C_COUNTER6_RESET_OFFSET    6
-#define    RTL8367C_COUNTER6_RESET_MASK    0x40
-#define    RTL8367C_COUNTER5_RESET_OFFSET    5
-#define    RTL8367C_COUNTER5_RESET_MASK    0x20
-#define    RTL8367C_COUNTER4_RESET_OFFSET    4
-#define    RTL8367C_COUNTER4_RESET_MASK    0x10
-#define    RTL8367C_COUNTER3_RESET_OFFSET    3
-#define    RTL8367C_COUNTER3_RESET_MASK    0x8
-#define    RTL8367C_COUNTER2_RESET_OFFSET    2
-#define    RTL8367C_COUNTER2_RESET_MASK    0x4
-#define    RTL8367C_COUNTER1_RESET_OFFSET    1
-#define    RTL8367C_COUNTER1_RESET_MASK    0x2
-#define    RTL8367C_COUNTER0_RESET_OFFSET    0
-#define    RTL8367C_COUNTER0_RESET_MASK    0x1
-
-#define    RTL8367C_REG_MIB_CTRL2    0x1008
-#define    RTL8367C_COUNTER31_RESET_OFFSET    15
-#define    RTL8367C_COUNTER31_RESET_MASK    0x8000
-#define    RTL8367C_COUNTER30_RESET_OFFSET    14
-#define    RTL8367C_COUNTER30_RESET_MASK    0x4000
-#define    RTL8367C_COUNTER29_RESET_OFFSET    13
-#define    RTL8367C_COUNTER29_RESET_MASK    0x2000
-#define    RTL8367C_COUNTER28_RESET_OFFSET    12
-#define    RTL8367C_COUNTER28_RESET_MASK    0x1000
-#define    RTL8367C_COUNTER27_RESET_OFFSET    11
-#define    RTL8367C_COUNTER27_RESET_MASK    0x800
-#define    RTL8367C_COUNTER26_RESET_OFFSET    10
-#define    RTL8367C_COUNTER26_RESET_MASK    0x400
-#define    RTL8367C_COUNTER25_RESET_OFFSET    9
-#define    RTL8367C_COUNTER25_RESET_MASK    0x200
-#define    RTL8367C_COUNTER24_RESET_OFFSET    8
-#define    RTL8367C_COUNTER24_RESET_MASK    0x100
-#define    RTL8367C_COUNTER23_RESET_OFFSET    7
-#define    RTL8367C_COUNTER23_RESET_MASK    0x80
-#define    RTL8367C_COUNTER22_RESET_OFFSET    6
-#define    RTL8367C_COUNTER22_RESET_MASK    0x40
-#define    RTL8367C_COUNTER21_RESET_OFFSET    5
-#define    RTL8367C_COUNTER21_RESET_MASK    0x20
-#define    RTL8367C_COUNTER20_RESET_OFFSET    4
-#define    RTL8367C_COUNTER20_RESET_MASK    0x10
-#define    RTL8367C_COUNTER19_RESET_OFFSET    3
-#define    RTL8367C_COUNTER19_RESET_MASK    0x8
-#define    RTL8367C_COUNTER18_RESET_OFFSET    2
-#define    RTL8367C_COUNTER18_RESET_MASK    0x4
-#define    RTL8367C_COUNTER17_RESET_OFFSET    1
-#define    RTL8367C_COUNTER17_RESET_MASK    0x2
-#define    RTL8367C_COUNTER16_RESET_OFFSET    0
-#define    RTL8367C_COUNTER16_RESET_MASK    0x1
-
-#define    RTL8367C_REG_MIB_CTRL3    0x1009
-#define    RTL8367C_COUNTER15_MODE_OFFSET    15
-#define    RTL8367C_COUNTER15_MODE_MASK    0x8000
-#define    RTL8367C_COUNTER14_MODE_OFFSET    14
-#define    RTL8367C_COUNTER14_MODE_MASK    0x4000
-#define    RTL8367C_COUNTER13_MODE_OFFSET    13
-#define    RTL8367C_COUNTER13_MODE_MASK    0x2000
-#define    RTL8367C_COUNTER12_MODE_OFFSET    12
-#define    RTL8367C_COUNTER12_MODE_MASK    0x1000
-#define    RTL8367C_COUNTER11_MODE_OFFSET    11
-#define    RTL8367C_COUNTER11_MODE_MASK    0x800
-#define    RTL8367C_COUNTER10_MODE_OFFSET    10
-#define    RTL8367C_COUNTER10_MODE_MASK    0x400
-#define    RTL8367C_COUNTER9_MODE_OFFSET    9
-#define    RTL8367C_COUNTER9_MODE_MASK    0x200
-#define    RTL8367C_COUNTER8_MODE_OFFSET    8
-#define    RTL8367C_COUNTER8_MODE_MASK    0x100
-#define    RTL8367C_COUNTER7_MODE_OFFSET    7
-#define    RTL8367C_COUNTER7_MODE_MASK    0x80
-#define    RTL8367C_COUNTER6_MODE_OFFSET    6
-#define    RTL8367C_COUNTER6_MODE_MASK    0x40
-#define    RTL8367C_COUNTER5_MODE_OFFSET    5
-#define    RTL8367C_COUNTER5_MODE_MASK    0x20
-#define    RTL8367C_COUNTER4_MODE_OFFSET    4
-#define    RTL8367C_COUNTER4_MODE_MASK    0x10
-#define    RTL8367C_COUNTER3_MODE_OFFSET    3
-#define    RTL8367C_COUNTER3_MODE_MASK    0x8
-#define    RTL8367C_COUNTER2_MODE_OFFSET    2
-#define    RTL8367C_COUNTER2_MODE_MASK    0x4
-#define    RTL8367C_COUNTER1_MODE_OFFSET    1
-#define    RTL8367C_COUNTER1_MODE_MASK    0x2
-#define    RTL8367C_COUNTER0_MODE_OFFSET    0
-#define    RTL8367C_COUNTER0_MODE_MASK    0x1
-
-#define    RTL8367C_REG_MIB_CTRL4    0x100a
-#define    RTL8367C_MIB_USAGE_MODE_OFFSET    8
-#define    RTL8367C_MIB_USAGE_MODE_MASK    0x100
-#define    RTL8367C_MIB_TIMER_OFFSET    0
-#define    RTL8367C_MIB_TIMER_MASK    0xFF
-
-#define    RTL8367C_REG_MIB_CTRL5    0x100b
-#define    RTL8367C_MIB_CTRL5_COUNTER15_TYPE_OFFSET    15
-#define    RTL8367C_MIB_CTRL5_COUNTER15_TYPE_MASK    0x8000
-#define    RTL8367C_MIB_CTRL5_COUNTER14_TYPE_OFFSET    14
-#define    RTL8367C_MIB_CTRL5_COUNTER14_TYPE_MASK    0x4000
-#define    RTL8367C_MIB_CTRL5_COUNTER13_TYPE_OFFSET    13
-#define    RTL8367C_MIB_CTRL5_COUNTER13_TYPE_MASK    0x2000
-#define    RTL8367C_MIB_CTRL5_COUNTER12_TYPE_OFFSET    12
-#define    RTL8367C_MIB_CTRL5_COUNTER12_TYPE_MASK    0x1000
-#define    RTL8367C_MIB_CTRL5_COUNTER11_TYPE_OFFSET    11
-#define    RTL8367C_MIB_CTRL5_COUNTER11_TYPE_MASK    0x800
-#define    RTL8367C_MIB_CTRL5_COUNTER10_TYPE_OFFSET    10
-#define    RTL8367C_MIB_CTRL5_COUNTER10_TYPE_MASK    0x400
-#define    RTL8367C_MIB_CTRL5_COUNTER9_TYPE_OFFSET    9
-#define    RTL8367C_MIB_CTRL5_COUNTER9_TYPE_MASK    0x200
-#define    RTL8367C_MIB_CTRL5_COUNTER8_TYPE_OFFSET    8
-#define    RTL8367C_MIB_CTRL5_COUNTER8_TYPE_MASK    0x100
-#define    RTL8367C_MIB_CTRL5_COUNTER7_TYPE_OFFSET    7
-#define    RTL8367C_MIB_CTRL5_COUNTER7_TYPE_MASK    0x80
-#define    RTL8367C_MIB_CTRL5_COUNTER6_TYPE_OFFSET    6
-#define    RTL8367C_MIB_CTRL5_COUNTER6_TYPE_MASK    0x40
-#define    RTL8367C_MIB_CTRL5_COUNTER5_TYPE_OFFSET    5
-#define    RTL8367C_MIB_CTRL5_COUNTER5_TYPE_MASK    0x20
-#define    RTL8367C_MIB_CTRL5_COUNTER4_TYPE_OFFSET    4
-#define    RTL8367C_MIB_CTRL5_COUNTER4_TYPE_MASK    0x10
-#define    RTL8367C_MIB_CTRL5_COUNTER3_TYPE_OFFSET    3
-#define    RTL8367C_MIB_CTRL5_COUNTER3_TYPE_MASK    0x8
-#define    RTL8367C_MIB_CTRL5_COUNTER2_TYPE_OFFSET    2
-#define    RTL8367C_MIB_CTRL5_COUNTER2_TYPE_MASK    0x4
-#define    RTL8367C_MIB_CTRL5_COUNTER1_TYPE_OFFSET    1
-#define    RTL8367C_MIB_CTRL5_COUNTER1_TYPE_MASK    0x2
-#define    RTL8367C_MIB_CTRL5_COUNTER0_TYPE_OFFSET    0
-#define    RTL8367C_MIB_CTRL5_COUNTER0_TYPE_MASK    0x1
-
-/* (16'h1100)intrpt_reg */
-
-#define    RTL8367C_REG_INTR_CTRL    0x1100
-#define    RTL8367C_INTR_CTRL_OFFSET    0
-#define    RTL8367C_INTR_CTRL_MASK    0x1
-
-#define    RTL8367C_REG_INTR_IMR    0x1101
-#define    RTL8367C_INTR_IMR_SLIENT_START_2_OFFSET    12
-#define    RTL8367C_INTR_IMR_SLIENT_START_2_MASK    0x1000
-#define    RTL8367C_INTR_IMR_SLIENT_START_OFFSET    11
-#define    RTL8367C_INTR_IMR_SLIENT_START_MASK    0x800
-#define    RTL8367C_INTR_IMR_ACL_ACTION_OFFSET    9
-#define    RTL8367C_INTR_IMR_ACL_ACTION_MASK    0x200
-#define    RTL8367C_INTR_IMR_CABLE_DIAG_FIN_OFFSET    8
-#define    RTL8367C_INTR_IMR_CABLE_DIAG_FIN_MASK    0x100
-#define    RTL8367C_INTR_IMR_INTERRUPT_8051_OFFSET    7
-#define    RTL8367C_INTR_IMR_INTERRUPT_8051_MASK    0x80
-#define    RTL8367C_INTR_IMR_LOOP_DETECTION_OFFSET    6
-#define    RTL8367C_INTR_IMR_LOOP_DETECTION_MASK    0x40
-#define    RTL8367C_INTR_IMR_GREEN_TIMER_OFFSET    5
-#define    RTL8367C_INTR_IMR_GREEN_TIMER_MASK    0x20
-#define    RTL8367C_INTR_IMR_SPECIAL_CONGEST_OFFSET    4
-#define    RTL8367C_INTR_IMR_SPECIAL_CONGEST_MASK    0x10
-#define    RTL8367C_INTR_IMR_SPEED_CHANGE_OFFSET    3
-#define    RTL8367C_INTR_IMR_SPEED_CHANGE_MASK    0x8
-#define    RTL8367C_INTR_IMR_LEARN_OVER_OFFSET    2
-#define    RTL8367C_INTR_IMR_LEARN_OVER_MASK    0x4
-#define    RTL8367C_INTR_IMR_METER_EXCEEDED_OFFSET    1
-#define    RTL8367C_INTR_IMR_METER_EXCEEDED_MASK    0x2
-#define    RTL8367C_INTR_IMR_LINK_CHANGE_OFFSET    0
-#define    RTL8367C_INTR_IMR_LINK_CHANGE_MASK    0x1
-
-#define    RTL8367C_REG_INTR_IMS    0x1102
-#define    RTL8367C_INTR_IMS_SLIENT_START_2_OFFSET    12
-#define    RTL8367C_INTR_IMS_SLIENT_START_2_MASK    0x1000
-#define    RTL8367C_INTR_IMS_SLIENT_START_OFFSET    11
-#define    RTL8367C_INTR_IMS_SLIENT_START_MASK    0x800
-#define    RTL8367C_INTR_IMS_ACL_ACTION_OFFSET    9
-#define    RTL8367C_INTR_IMS_ACL_ACTION_MASK    0x200
-#define    RTL8367C_INTR_IMS_CABLE_DIAG_FIN_OFFSET    8
-#define    RTL8367C_INTR_IMS_CABLE_DIAG_FIN_MASK    0x100
-#define    RTL8367C_INTR_IMS_INTERRUPT_8051_OFFSET    7
-#define    RTL8367C_INTR_IMS_INTERRUPT_8051_MASK    0x80
-#define    RTL8367C_INTR_IMS_LOOP_DETECTION_OFFSET    6
-#define    RTL8367C_INTR_IMS_LOOP_DETECTION_MASK    0x40
-#define    RTL8367C_INTR_IMS_GREEN_TIMER_OFFSET    5
-#define    RTL8367C_INTR_IMS_GREEN_TIMER_MASK    0x20
-#define    RTL8367C_INTR_IMS_SPECIAL_CONGEST_OFFSET    4
-#define    RTL8367C_INTR_IMS_SPECIAL_CONGEST_MASK    0x10
-#define    RTL8367C_INTR_IMS_SPEED_CHANGE_OFFSET    3
-#define    RTL8367C_INTR_IMS_SPEED_CHANGE_MASK    0x8
-#define    RTL8367C_INTR_IMS_LEARN_OVER_OFFSET    2
-#define    RTL8367C_INTR_IMS_LEARN_OVER_MASK    0x4
-#define    RTL8367C_INTR_IMS_METER_EXCEEDED_OFFSET    1
-#define    RTL8367C_INTR_IMS_METER_EXCEEDED_MASK    0x2
-#define    RTL8367C_INTR_IMS_LINK_CHANGE_OFFSET    0
-#define    RTL8367C_INTR_IMS_LINK_CHANGE_MASK    0x1
-
-#define    RTL8367C_REG_LEARN_OVER_INDICATOR    0x1103
-#define    RTL8367C_LEARN_OVER_INDICATOR_OFFSET    0
-#define    RTL8367C_LEARN_OVER_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_SPEED_CHANGE_INDICATOR    0x1104
-#define    RTL8367C_SPEED_CHANGE_INDICATOR_OFFSET    0
-#define    RTL8367C_SPEED_CHANGE_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_SPECIAL_CONGEST_INDICATOR    0x1105
-#define    RTL8367C_SPECIAL_CONGEST_INDICATOR_OFFSET    0
-#define    RTL8367C_SPECIAL_CONGEST_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_LINKDOWN_INDICATOR    0x1106
-#define    RTL8367C_PORT_LINKDOWN_INDICATOR_OFFSET    0
-#define    RTL8367C_PORT_LINKDOWN_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_LINKUP_INDICATOR    0x1107
-#define    RTL8367C_PORT_LINKUP_INDICATOR_OFFSET    0
-#define    RTL8367C_PORT_LINKUP_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_SYSTEM_LEARN_OVER_INDICATOR    0x1108
-#define    RTL8367C_SYSTEM_LEARN_OVER_INDICATOR_OFFSET    0
-#define    RTL8367C_SYSTEM_LEARN_OVER_INDICATOR_MASK    0x1
-
-#define    RTL8367C_REG_INTR_IMR_8051    0x1118
-#define    RTL8367C_INTR_IMR_8051_SLIENT_START_2_OFFSET    13
-#define    RTL8367C_INTR_IMR_8051_SLIENT_START_2_MASK    0x2000
-#define    RTL8367C_INTR_IMR_8051_SLIENT_START_OFFSET    12
-#define    RTL8367C_INTR_IMR_8051_SLIENT_START_MASK    0x1000
-#define    RTL8367C_INTR_IMR_8051_ACL_ACTION_OFFSET    10
-#define    RTL8367C_INTR_IMR_8051_ACL_ACTION_MASK    0x400
-#define    RTL8367C_INTR_IMR_8051_SAMOVING_8051_OFFSET    9
-#define    RTL8367C_INTR_IMR_8051_SAMOVING_8051_MASK    0x200
-#define    RTL8367C_INTR_IMR_8051_CABLE_DIAG_FIN_8051_OFFSET    8
-#define    RTL8367C_INTR_IMR_8051_CABLE_DIAG_FIN_8051_MASK    0x100
-#define    RTL8367C_INTR_IMR_8051_EEELLDP_8051_OFFSET    7
-#define    RTL8367C_INTR_IMR_8051_EEELLDP_8051_MASK    0x80
-#define    RTL8367C_INTR_IMR_8051_LOOP_DETECTION_8051_OFFSET    6
-#define    RTL8367C_INTR_IMR_8051_LOOP_DETECTION_8051_MASK    0x40
-#define    RTL8367C_INTR_IMR_8051_GREEN_TIMER_8051_OFFSET    5
-#define    RTL8367C_INTR_IMR_8051_GREEN_TIMER_8051_MASK    0x20
-#define    RTL8367C_INTR_IMR_8051_SPECIAL_CONGEST_8051_OFFSET    4
-#define    RTL8367C_INTR_IMR_8051_SPECIAL_CONGEST_8051_MASK    0x10
-#define    RTL8367C_INTR_IMR_8051_SPEED_CHANGE_8051_OFFSET    3
-#define    RTL8367C_INTR_IMR_8051_SPEED_CHANGE_8051_MASK    0x8
-#define    RTL8367C_INTR_IMR_8051_LEARN_OVER_8051_OFFSET    2
-#define    RTL8367C_INTR_IMR_8051_LEARN_OVER_8051_MASK    0x4
-#define    RTL8367C_INTR_IMR_8051_METER_EXCEEDED_8051_OFFSET    1
-#define    RTL8367C_INTR_IMR_8051_METER_EXCEEDED_8051_MASK    0x2
-#define    RTL8367C_INTR_IMR_8051_LINK_CHANGE_8051_OFFSET    0
-#define    RTL8367C_INTR_IMR_8051_LINK_CHANGE_8051_MASK    0x1
-
-#define    RTL8367C_REG_INTR_IMS_8051    0x1119
-#define    RTL8367C_INTR_IMS_8051_SLIENT_START_2_OFFSET    13
-#define    RTL8367C_INTR_IMS_8051_SLIENT_START_2_MASK    0x2000
-#define    RTL8367C_INTR_IMS_8051_SLIENT_START_OFFSET    12
-#define    RTL8367C_INTR_IMS_8051_SLIENT_START_MASK    0x1000
-#define    RTL8367C_INTR_IMS_8051_ACL_ACTION_OFFSET    10
-#define    RTL8367C_INTR_IMS_8051_ACL_ACTION_MASK    0x400
-#define    RTL8367C_INTR_IMS_8051_SAMOVING_8051_OFFSET    9
-#define    RTL8367C_INTR_IMS_8051_SAMOVING_8051_MASK    0x200
-#define    RTL8367C_INTR_IMS_8051_CABLE_DIAG_FIN_8051_OFFSET    8
-#define    RTL8367C_INTR_IMS_8051_CABLE_DIAG_FIN_8051_MASK    0x100
-#define    RTL8367C_INTR_IMS_8051_EEELLDP_8051_OFFSET    7
-#define    RTL8367C_INTR_IMS_8051_EEELLDP_8051_MASK    0x80
-#define    RTL8367C_INTR_IMS_8051_LOOP_DETECTION_8051_OFFSET    6
-#define    RTL8367C_INTR_IMS_8051_LOOP_DETECTION_8051_MASK    0x40
-#define    RTL8367C_INTR_IMS_8051_GREEN_TIMER_8051_OFFSET    5
-#define    RTL8367C_INTR_IMS_8051_GREEN_TIMER_8051_MASK    0x20
-#define    RTL8367C_INTR_IMS_8051_SPECIAL_CONGEST_8051_OFFSET    4
-#define    RTL8367C_INTR_IMS_8051_SPECIAL_CONGEST_8051_MASK    0x10
-#define    RTL8367C_INTR_IMS_8051_SPEED_CHANGE_8051_OFFSET    3
-#define    RTL8367C_INTR_IMS_8051_SPEED_CHANGE_8051_MASK    0x8
-#define    RTL8367C_INTR_IMS_8051_LEARN_OVER_8051_OFFSET    2
-#define    RTL8367C_INTR_IMS_8051_LEARN_OVER_8051_MASK    0x4
-#define    RTL8367C_INTR_IMS_8051_METER_EXCEEDED_8051_OFFSET    1
-#define    RTL8367C_INTR_IMS_8051_METER_EXCEEDED_8051_MASK    0x2
-#define    RTL8367C_INTR_IMS_8051_LINK_CHANGE_8051_OFFSET    0
-#define    RTL8367C_INTR_IMS_8051_LINK_CHANGE_8051_MASK    0x1
-
-#define    RTL8367C_REG_DW8051_INT_CPU    0x111a
-#define    RTL8367C_DW8051_INT_CPU_OFFSET    0
-#define    RTL8367C_DW8051_INT_CPU_MASK    0x1
-
-#define    RTL8367C_REG_LEARN_OVER_INDICATOR_8051    0x1120
-#define    RTL8367C_LEARN_OVER_INDICATOR_8051_OFFSET    0
-#define    RTL8367C_LEARN_OVER_INDICATOR_8051_MASK    0x7FF
-
-#define    RTL8367C_REG_SPEED_CHANGE_INDICATOR_8051    0x1121
-#define    RTL8367C_SPEED_CHANGE_INDICATOR_8051_OFFSET    0
-#define    RTL8367C_SPEED_CHANGE_INDICATOR_8051_MASK    0x7FF
-
-#define    RTL8367C_REG_SPECIAL_CONGEST_INDICATOR_8051    0x1122
-#define    RTL8367C_SPECIAL_CONGEST_INDICATOR_8051_OFFSET    0
-#define    RTL8367C_SPECIAL_CONGEST_INDICATOR_8051_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_LINKDOWN_INDICATOR_8051    0x1123
-#define    RTL8367C_PORT_LINKDOWN_INDICATOR_8051_OFFSET    0
-#define    RTL8367C_PORT_LINKDOWN_INDICATOR_8051_MASK    0x7FF
-
-#define    RTL8367C_REG_PORT_LINKUP_INDICATOR_8051    0x1124
-#define    RTL8367C_PORT_LINKUP_INDICATOR_8051_OFFSET    0
-#define    RTL8367C_PORT_LINKUP_INDICATOR_8051_MASK    0x7FF
-
-#define    RTL8367C_REG_DUMMY_1125    0x1125
-
-#define    RTL8367C_REG_DUMMY_1126    0x1126
-
-#define    RTL8367C_REG_DUMMY_1127    0x1127
-
-#define    RTL8367C_REG_DUMMY_1128    0x1128
-
-#define    RTL8367C_REG_DUMMY_1129    0x1129
-
-#define    RTL8367C_REG_INTR_IMS_BUFFER_RESET    0x112a
-#define    RTL8367C_INTR_IMS_BUFFER_RESET_IMR_BUFF_RESET_OFFSET    1
-#define    RTL8367C_INTR_IMS_BUFFER_RESET_IMR_BUFF_RESET_MASK    0x2
-#define    RTL8367C_INTR_IMS_BUFFER_RESET_BUFFER_RESET_OFFSET    0
-#define    RTL8367C_INTR_IMS_BUFFER_RESET_BUFFER_RESET_MASK    0x1
-
-#define    RTL8367C_REG_INTR_IMS_8051_BUFFER_RESET    0x112b
-#define    RTL8367C_INTR_IMS_8051_BUFFER_RESET_IMR_BUFF_RESET_OFFSET    1
-#define    RTL8367C_INTR_IMS_8051_BUFFER_RESET_IMR_BUFF_RESET_MASK    0x2
-#define    RTL8367C_INTR_IMS_8051_BUFFER_RESET_BUFFER_RESET_OFFSET    0
-#define    RTL8367C_INTR_IMS_8051_BUFFER_RESET_BUFFER_RESET_MASK    0x1
-
-#define    RTL8367C_REG_GPHY_INTRPT_8051    0x112c
-#define    RTL8367C_IMS_GPHY_8051_H_OFFSET    13
-#define    RTL8367C_IMS_GPHY_8051_H_MASK    0xE000
-#define    RTL8367C_IMR_GPHY_8051_H_OFFSET    10
-#define    RTL8367C_IMR_GPHY_8051_H_MASK    0x1C00
-#define    RTL8367C_IMS_GPHY_8051_OFFSET    5
-#define    RTL8367C_IMS_GPHY_8051_MASK    0x3E0
-#define    RTL8367C_IMR_GPHY_8051_OFFSET    0
-#define    RTL8367C_IMR_GPHY_8051_MASK    0x1F
-
-#define    RTL8367C_REG_GPHY_INTRPT    0x112d
-#define    RTL8367C_IMS_GPHY_H_OFFSET    13
-#define    RTL8367C_IMS_GPHY_H_MASK    0xE000
-#define    RTL8367C_IMR_GPHY_H_OFFSET    10
-#define    RTL8367C_IMR_GPHY_H_MASK    0x1C00
-#define    RTL8367C_IMS_GPHY_OFFSET    5
-#define    RTL8367C_IMS_GPHY_MASK    0x3E0
-#define    RTL8367C_IMR_GPHY_OFFSET    0
-#define    RTL8367C_IMR_GPHY_MASK    0x1F
-
-#define    RTL8367C_REG_THERMAL_INTRPT    0x112e
-#define    RTL8367C_IMS_TM_HIGH_OFFSET    3
-#define    RTL8367C_IMS_TM_HIGH_MASK    0x8
-#define    RTL8367C_IMR_TM_HIGH_OFFSET    2
-#define    RTL8367C_IMR_TM_HIGH_MASK    0x4
-#define    RTL8367C_IMS_TM_LOW_OFFSET    1
-#define    RTL8367C_IMS_TM_LOW_MASK    0x2
-#define    RTL8367C_IMR_TM_LOW_OFFSET    0
-#define    RTL8367C_IMR_TM_LOW_MASK    0x1
-
-#define    RTL8367C_REG_THERMAL_INTRPT_8051    0x112f
-#define    RTL8367C_IMS_TM_HIGH_8051_OFFSET    3
-#define    RTL8367C_IMS_TM_HIGH_8051_MASK    0x8
-#define    RTL8367C_IMR_TM_HIGH_8051_OFFSET    2
-#define    RTL8367C_IMR_TM_HIGH_8051_MASK    0x4
-#define    RTL8367C_IMS_TM_LOW_8051_OFFSET    1
-#define    RTL8367C_IMS_TM_LOW_8051_MASK    0x2
-#define    RTL8367C_IMR_TM_LOW_8051_OFFSET    0
-#define    RTL8367C_IMR_TM_LOW_8051_MASK    0x1
-
-#define    RTL8367C_REG_SDS_LINK_CHG_INT    0x1130
-#define    RTL8367C_IMS_SDS_LINK_STS_C7_OFFSET    15
-#define    RTL8367C_IMS_SDS_LINK_STS_C7_MASK    0x8000
-#define    RTL8367C_IMS_SDS_LINK_STS_C6_OFFSET    14
-#define    RTL8367C_IMS_SDS_LINK_STS_C6_MASK    0x4000
-#define    RTL8367C_IMS_SDS_LINK_STS_C5_OFFSET    13
-#define    RTL8367C_IMS_SDS_LINK_STS_C5_MASK    0x2000
-#define    RTL8367C_IMS_SDS_LINK_STS_C4_OFFSET    12
-#define    RTL8367C_IMS_SDS_LINK_STS_C4_MASK    0x1000
-#define    RTL8367C_IMS_SDS_LINK_STS_C3_OFFSET    11
-#define    RTL8367C_IMS_SDS_LINK_STS_C3_MASK    0x800
-#define    RTL8367C_IMS_SDS_LINK_STS_C2_OFFSET    10
-#define    RTL8367C_IMS_SDS_LINK_STS_C2_MASK    0x400
-#define    RTL8367C_IMS_SDS_LINK_STS_C1_OFFSET    9
-#define    RTL8367C_IMS_SDS_LINK_STS_C1_MASK    0x200
-#define    RTL8367C_IMS_SDS_LINK_STS_C0_OFFSET    8
-#define    RTL8367C_IMS_SDS_LINK_STS_C0_MASK    0x100
-#define    RTL8367C_IMR_SDS_LINK_STS_C7_OFFSET    7
-#define    RTL8367C_IMR_SDS_LINK_STS_C7_MASK    0x80
-#define    RTL8367C_IMR_SDS_LINK_STS_C6_OFFSET    6
-#define    RTL8367C_IMR_SDS_LINK_STS_C6_MASK    0x40
-#define    RTL8367C_IMR_SDS_LINK_STS_C5_OFFSET    5
-#define    RTL8367C_IMR_SDS_LINK_STS_C5_MASK    0x20
-#define    RTL8367C_IMR_SDS_LINK_STS_C4_OFFSET    4
-#define    RTL8367C_IMR_SDS_LINK_STS_C4_MASK    0x10
-#define    RTL8367C_IMR_SDS_LINK_STS_C3_OFFSET    3
-#define    RTL8367C_IMR_SDS_LINK_STS_C3_MASK    0x8
-#define    RTL8367C_IMR_SDS_LINK_STS_C2_OFFSET    2
-#define    RTL8367C_IMR_SDS_LINK_STS_C2_MASK    0x4
-#define    RTL8367C_IMR_SDS_LINK_STS_C1_OFFSET    1
-#define    RTL8367C_IMR_SDS_LINK_STS_C1_MASK    0x2
-#define    RTL8367C_IMR_SDS_LINK_STS_C0_OFFSET    0
-#define    RTL8367C_IMR_SDS_LINK_STS_C0_MASK    0x1
-
-#define    RTL8367C_REG_SDS_LINK_CHG_INT_8051    0x1131
-#define    RTL8367C_IMS_SDS_LINK_STS_C7_8051_OFFSET    15
-#define    RTL8367C_IMS_SDS_LINK_STS_C7_8051_MASK    0x8000
-#define    RTL8367C_IMS_SDS_LINK_STS_C6_8051_OFFSET    14
-#define    RTL8367C_IMS_SDS_LINK_STS_C6_8051_MASK    0x4000
-#define    RTL8367C_IMS_SDS_LINK_STS_C5_8051_OFFSET    13
-#define    RTL8367C_IMS_SDS_LINK_STS_C5_8051_MASK    0x2000
-#define    RTL8367C_IMS_SDS_LINK_STS_C4_8051_OFFSET    12
-#define    RTL8367C_IMS_SDS_LINK_STS_C4_8051_MASK    0x1000
-#define    RTL8367C_IMS_SDS_LINK_STS_C3_8051_OFFSET    11
-#define    RTL8367C_IMS_SDS_LINK_STS_C3_8051_MASK    0x800
-#define    RTL8367C_IMS_SDS_LINK_STS_C2_8051_OFFSET    10
-#define    RTL8367C_IMS_SDS_LINK_STS_C2_8051_MASK    0x400
-#define    RTL8367C_IMS_SDS_LINK_STS_C1_8051_OFFSET    9
-#define    RTL8367C_IMS_SDS_LINK_STS_C1_8051_MASK    0x200
-#define    RTL8367C_IMS_SDS_LINK_STS_C0_8051_OFFSET    8
-#define    RTL8367C_IMS_SDS_LINK_STS_C0_8051_MASK    0x100
-#define    RTL8367C_IMR_SDS_LINK_STS_C7_8051_OFFSET    7
-#define    RTL8367C_IMR_SDS_LINK_STS_C7_8051_MASK    0x80
-#define    RTL8367C_IMR_SDS_LINK_STS_C6_8051_OFFSET    6
-#define    RTL8367C_IMR_SDS_LINK_STS_C6_8051_MASK    0x40
-#define    RTL8367C_IMR_SDS_LINK_STS_C5_8051_OFFSET    5
-#define    RTL8367C_IMR_SDS_LINK_STS_C5_8051_MASK    0x20
-#define    RTL8367C_IMR_SDS_LINK_STS_C4_8051_OFFSET    4
-#define    RTL8367C_IMR_SDS_LINK_STS_C4_8051_MASK    0x10
-#define    RTL8367C_IMR_SDS_LINK_STS_C3_8051_OFFSET    3
-#define    RTL8367C_IMR_SDS_LINK_STS_C3_8051_MASK    0x8
-#define    RTL8367C_IMR_SDS_LINK_STS_C2_8051_OFFSET    2
-#define    RTL8367C_IMR_SDS_LINK_STS_C2_8051_MASK    0x4
-#define    RTL8367C_IMR_SDS_LINK_STS_C1_8051_OFFSET    1
-#define    RTL8367C_IMR_SDS_LINK_STS_C1_8051_MASK    0x2
-#define    RTL8367C_IMR_SDS_LINK_STS_C0_8051_OFFSET    0
-#define    RTL8367C_IMR_SDS_LINK_STS_C0_8051_MASK    0x1
-
-/* (16'h1200)swcore_reg */
-
-#define    RTL8367C_REG_MAX_LENGTH_LIMINT_IPG    0x1200
-#define    RTL8367C_MAX_LENTH_CTRL_OFFSET    13
-#define    RTL8367C_MAX_LENTH_CTRL_MASK    0x6000
-#define    RTL8367C_PAGES_BEFORE_FCDROP_OFFSET    6
-#define    RTL8367C_PAGES_BEFORE_FCDROP_MASK    0x1FC0
-#define    RTL8367C_CHECK_MIN_IPG_RXDV_OFFSET    5
-#define    RTL8367C_CHECK_MIN_IPG_RXDV_MASK    0x20
-#define    RTL8367C_LIMIT_IPG_CFG_OFFSET    0
-#define    RTL8367C_LIMIT_IPG_CFG_MASK    0x1F
-
-#define    RTL8367C_REG_IOL_RXDROP_CFG    0x1201
-#define    RTL8367C_RX_IOL_MAX_LENGTH_CFG_OFFSET    13
-#define    RTL8367C_RX_IOL_MAX_LENGTH_CFG_MASK    0x2000
-#define    RTL8367C_RX_IOL_ERROR_LENGTH_CFG_OFFSET    12
-#define    RTL8367C_RX_IOL_ERROR_LENGTH_CFG_MASK    0x1000
-#define    RTL8367C_RX_NODROP_PAUSE_CFG_OFFSET    8
-#define    RTL8367C_RX_NODROP_PAUSE_CFG_MASK    0x100
-#define    RTL8367C_RX_DV_CNT_CFG_OFFSET    0
-#define    RTL8367C_RX_DV_CNT_CFG_MASK    0x3F
-
-#define    RTL8367C_REG_VS_TPID    0x1202
-
-#define    RTL8367C_REG_INBW_BOUND    0x1203
-#define    RTL8367C_LBOUND_OFFSET    4
-#define    RTL8367C_LBOUND_MASK    0xF0
-#define    RTL8367C_HBOUND_OFFSET    0
-#define    RTL8367C_HBOUND_MASK    0xF
-
-#define    RTL8367C_REG_CFG_TX_ITFSP_OP    0x1204
-#define    RTL8367C_MASK_OFFSET    1
-#define    RTL8367C_MASK_MASK    0x2
-#define    RTL8367C_OP_OFFSET    0
-#define    RTL8367C_OP_MASK    0x1
-
-#define    RTL8367C_REG_INBW_BOUND2    0x1205
-#define    RTL8367C_LBOUND2_H_OFFSET    9
-#define    RTL8367C_LBOUND2_H_MASK    0x200
-#define    RTL8367C_HBOUND2_H_OFFSET    8
-#define    RTL8367C_HBOUND2_H_MASK    0x100
-#define    RTL8367C_LBOUND2_OFFSET    4
-#define    RTL8367C_LBOUND2_MASK    0xF0
-#define    RTL8367C_HBOUND2_OFFSET    0
-#define    RTL8367C_HBOUND2_MASK    0xF
-
-#define    RTL8367C_REG_CFG_48PASS1_DROP    0x1206
-#define    RTL8367C_CFG_48PASS1_DROP_OFFSET    0
-#define    RTL8367C_CFG_48PASS1_DROP_MASK    0x1
-
-#define    RTL8367C_REG_CFG_BACKPRESSURE    0x1207
-#define    RTL8367C_LONGTXE_OFFSET    12
-#define    RTL8367C_LONGTXE_MASK    0x1000
-#define    RTL8367C_EN_BYPASS_ERROR_OFFSET    8
-#define    RTL8367C_EN_BYPASS_ERROR_MASK    0x100
-#define    RTL8367C_EN_BACKPRESSURE_OFFSET    4
-#define    RTL8367C_EN_BACKPRESSURE_MASK    0x10
-#define    RTL8367C_EN_48_PASS_1_OFFSET    0
-#define    RTL8367C_EN_48_PASS_1_MASK    0x1
-
-#define    RTL8367C_REG_CFG_UNHIOL    0x1208
-#define    RTL8367C_IOL_BACKOFF_OFFSET    12
-#define    RTL8367C_IOL_BACKOFF_MASK    0x1000
-#define    RTL8367C_BACKOFF_RANDOM_TIME_OFFSET    8
-#define    RTL8367C_BACKOFF_RANDOM_TIME_MASK    0x100
-#define    RTL8367C_DISABLE_BACK_OFF_OFFSET    4
-#define    RTL8367C_DISABLE_BACK_OFF_MASK    0x10
-#define    RTL8367C_IPG_COMPENSATION_OFFSET    0
-#define    RTL8367C_IPG_COMPENSATION_MASK    0x1
-
-#define    RTL8367C_REG_SWITCH_MAC0    0x1209
-
-#define    RTL8367C_REG_SWITCH_MAC1    0x120a
-
-#define    RTL8367C_REG_SWITCH_MAC2    0x120b
-
-#define    RTL8367C_REG_SWITCH_CTRL0    0x120c
-#define    RTL8367C_REMARKING_DSCP_ENABLE_OFFSET    8
-#define    RTL8367C_REMARKING_DSCP_ENABLE_MASK    0x100
-#define    RTL8367C_SHORT_IPG_OFFSET    4
-#define    RTL8367C_SHORT_IPG_MASK    0x10
-#define    RTL8367C_PAUSE_MAX128_OFFSET    0
-#define    RTL8367C_PAUSE_MAX128_MASK    0x1
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_CTRL0    0x120d
-#define    RTL8367C_INTPRI1_DSCP_OFFSET    8
-#define    RTL8367C_INTPRI1_DSCP_MASK    0x3F00
-#define    RTL8367C_INTPRI0_DSCP_OFFSET    0
-#define    RTL8367C_INTPRI0_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_CTRL1    0x120e
-#define    RTL8367C_INTPRI3_DSCP_OFFSET    8
-#define    RTL8367C_INTPRI3_DSCP_MASK    0x3F00
-#define    RTL8367C_INTPRI2_DSCP_OFFSET    0
-#define    RTL8367C_INTPRI2_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_CTRL2    0x120f
-#define    RTL8367C_INTPRI5_DSCP_OFFSET    8
-#define    RTL8367C_INTPRI5_DSCP_MASK    0x3F00
-#define    RTL8367C_INTPRI4_DSCP_OFFSET    0
-#define    RTL8367C_INTPRI4_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_DSCP_REMARK_CTRL3    0x1210
-#define    RTL8367C_INTPRI7_DSCP_OFFSET    8
-#define    RTL8367C_INTPRI7_DSCP_MASK    0x3F00
-#define    RTL8367C_INTPRI6_DSCP_OFFSET    0
-#define    RTL8367C_INTPRI6_DSCP_MASK    0x3F
-
-#define    RTL8367C_REG_QOS_1Q_REMARK_CTRL0    0x1211
-#define    RTL8367C_INTPRI3_PRI_OFFSET    12
-#define    RTL8367C_INTPRI3_PRI_MASK    0x7000
-#define    RTL8367C_INTPRI2_PRI_OFFSET    8
-#define    RTL8367C_INTPRI2_PRI_MASK    0x700
-#define    RTL8367C_INTPRI1_PRI_OFFSET    4
-#define    RTL8367C_INTPRI1_PRI_MASK    0x70
-#define    RTL8367C_INTPRI0_PRI_OFFSET    0
-#define    RTL8367C_INTPRI0_PRI_MASK    0x7
-
-#define    RTL8367C_REG_QOS_1Q_REMARK_CTRL1    0x1212
-#define    RTL8367C_INTPRI7_PRI_OFFSET    12
-#define    RTL8367C_INTPRI7_PRI_MASK    0x7000
-#define    RTL8367C_INTPRI6_PRI_OFFSET    8
-#define    RTL8367C_INTPRI6_PRI_MASK    0x700
-#define    RTL8367C_INTPRI5_PRI_OFFSET    4
-#define    RTL8367C_INTPRI5_PRI_MASK    0x70
-#define    RTL8367C_INTPRI4_PRI_OFFSET    0
-#define    RTL8367C_INTPRI4_PRI_MASK    0x7
-
-#define    RTL8367C_REG_PKTGEN_COMMAND    0x1213
-#define    RTL8367C_PKTGEN_STOP_OFFSET    8
-#define    RTL8367C_PKTGEN_STOP_MASK    0x100
-#define    RTL8367C_PKTGEN_START_OFFSET    4
-#define    RTL8367C_PKTGEN_START_MASK    0x10
-#define    RTL8367C_PKTGEN_BYPASS_FLOWCONTROL_OFFSET    0
-#define    RTL8367C_PKTGEN_BYPASS_FLOWCONTROL_MASK    0x1
-
-#define    RTL8367C_REG_SW_DUMMY0    0x1214
-#define    RTL8367C_SW_DUMMY0_DUMMY_OFFSET    4
-#define    RTL8367C_SW_DUMMY0_DUMMY_MASK    0xFFF0
-#define    RTL8367C_EEE_DEFER_TXLPI_OFFSET    3
-#define    RTL8367C_EEE_DEFER_TXLPI_MASK    0x8
-#define    RTL8367C_INGRESSBW_BYPASS_EN_OFFSET    2
-#define    RTL8367C_INGRESSBW_BYPASS_EN_MASK    0x4
-#define    RTL8367C_CFG_RX_MIN_OFFSET    0
-#define    RTL8367C_CFG_RX_MIN_MASK    0x3
-
-#define    RTL8367C_REG_SW_DUMMY1    0x1215
-
-#define    RTL8367C_REG_PKTGEN_PAUSE_TIME    0x1216
-
-#define    RTL8367C_REG_SVLAN_UPLINK_PORTMASK    0x1218
-#define    RTL8367C_SVLAN_UPLINK_PORTMASK_OFFSET    0
-#define    RTL8367C_SVLAN_UPLINK_PORTMASK_MASK    0x7FF
-
-#define    RTL8367C_REG_CPU_PORT_MASK    0x1219
-#define    RTL8367C_CPU_PORT_MASK_OFFSET    0
-#define    RTL8367C_CPU_PORT_MASK_MASK    0x7FF
-
-#define    RTL8367C_REG_CPU_CTRL    0x121a
-#define    RTL8367C_CPU_TRAP_PORT_EXT_OFFSET    10
-#define    RTL8367C_CPU_TRAP_PORT_EXT_MASK    0x400
-#define    RTL8367C_CPU_TAG_FORMAT_OFFSET    9
-#define    RTL8367C_CPU_TAG_FORMAT_MASK    0x200
-#define    RTL8367C_IOL_16DROP_OFFSET    8
-#define    RTL8367C_IOL_16DROP_MASK    0x100
-#define    RTL8367C_CPU_TAG_RXBYTECOUNT_OFFSET    7
-#define    RTL8367C_CPU_TAG_RXBYTECOUNT_MASK    0x80
-#define    RTL8367C_CPU_TAG_POSITION_OFFSET    6
-#define    RTL8367C_CPU_TAG_POSITION_MASK    0x40
-#define    RTL8367C_CPU_TRAP_PORT_OFFSET    3
-#define    RTL8367C_CPU_TRAP_PORT_MASK    0x38
-#define    RTL8367C_CPU_INSERTMODE_OFFSET    1
-#define    RTL8367C_CPU_INSERTMODE_MASK    0x6
-#define    RTL8367C_CPU_EN_OFFSET    0
-#define    RTL8367C_CPU_EN_MASK    0x1
-
-#define    RTL8367C_REG_MIRROR_CTRL    0x121c
-#define    RTL8367C_MIRROR_CTRL_DUMMY_OFFSET    12
-#define    RTL8367C_MIRROR_CTRL_DUMMY_MASK    0xF000
-#define    RTL8367C_MIRROR_ISO_OFFSET    11
-#define    RTL8367C_MIRROR_ISO_MASK    0x800
-#define    RTL8367C_MIRROR_TX_OFFSET    10
-#define    RTL8367C_MIRROR_TX_MASK    0x400
-#define    RTL8367C_MIRROR_RX_OFFSET    9
-#define    RTL8367C_MIRROR_RX_MASK    0x200
-#define    RTL8367C_MIRROR_MONITOR_PORT_OFFSET    4
-#define    RTL8367C_MIRROR_MONITOR_PORT_MASK    0xF0
-#define    RTL8367C_MIRROR_SOURCE_PORT_OFFSET    0
-#define    RTL8367C_MIRROR_SOURCE_PORT_MASK    0xF
-
-#define    RTL8367C_REG_FLOWCTRL_CTRL0    0x121d
-#define    RTL8367C_FLOWCTRL_TYPE_OFFSET    15
-#define    RTL8367C_FLOWCTRL_TYPE_MASK    0x8000
-#define    RTL8367C_DROP_ALL_THRESHOLD_OFFSET    5
-#define    RTL8367C_DROP_ALL_THRESHOLD_MASK    0x7FE0
-#define    RTL8367C_DROP_ALL_THRESHOLD_MSB_OFFSET    4
-#define    RTL8367C_DROP_ALL_THRESHOLD_MSB_MASK    0x10
-#define    RTL8367C_ITFSP_REG_OFFSET    0
-#define    RTL8367C_ITFSP_REG_MASK    0x7
-
-#define    RTL8367C_REG_FLOWCTRL_ALL_ON    0x121e
-#define    RTL8367C_CFG_RLDPACT_OFFSET    12
-#define    RTL8367C_CFG_RLDPACT_MASK    0x1000
-#define    RTL8367C_FLOWCTRL_ALL_ON_THRESHOLD_OFFSET    0
-#define    RTL8367C_FLOWCTRL_ALL_ON_THRESHOLD_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_SYS_ON    0x121f
-#define    RTL8367C_FLOWCTRL_SYS_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_SYS_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_SYS_OFF    0x1220
-#define    RTL8367C_FLOWCTRL_SYS_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_SYS_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_SHARE_ON    0x1221
-#define    RTL8367C_FLOWCTRL_SHARE_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_SHARE_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_SHARE_OFF    0x1222
-#define    RTL8367C_FLOWCTRL_SHARE_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_SHARE_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_SYS_ON    0x1223
-#define    RTL8367C_FLOWCTRL_FCOFF_SYS_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_SYS_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_SYS_OFF    0x1224
-#define    RTL8367C_FLOWCTRL_FCOFF_SYS_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_SYS_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_SHARE_ON    0x1225
-#define    RTL8367C_FLOWCTRL_FCOFF_SHARE_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_SHARE_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_SHARE_OFF    0x1226
-#define    RTL8367C_FLOWCTRL_FCOFF_SHARE_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_SHARE_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT_ON    0x1227
-#define    RTL8367C_FLOWCTRL_PORT_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT_OFF    0x1228
-#define    RTL8367C_FLOWCTRL_PORT_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT_PRIVATE_ON    0x1229
-#define    RTL8367C_FLOWCTRL_PORT_PRIVATE_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT_PRIVATE_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT_PRIVATE_OFF    0x122a
-#define    RTL8367C_FLOWCTRL_PORT_PRIVATE_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT_PRIVATE_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_RRCP_CTRL0    0x122b
-#define    RTL8367C_COL_SEL_OFFSET    14
-#define    RTL8367C_COL_SEL_MASK    0x4000
-#define    RTL8367C_CRS_SEL_OFFSET    13
-#define    RTL8367C_CRS_SEL_MASK    0x2000
-#define    RTL8367C_RRCP_PBVLAN_EN_OFFSET    11
-#define    RTL8367C_RRCP_PBVLAN_EN_MASK    0x800
-#define    RTL8367C_RRCPV3_SECURITY_CRC_OFFSET    10
-#define    RTL8367C_RRCPV3_SECURITY_CRC_MASK    0x400
-#define    RTL8367C_RRCPV3_HANDLE_OFFSET    8
-#define    RTL8367C_RRCPV3_HANDLE_MASK    0x300
-#define    RTL8367C_RRCPV1_MALFORMED_ACT_OFFSET    5
-#define    RTL8367C_RRCPV1_MALFORMED_ACT_MASK    0x60
-#define    RTL8367C_RRCP_VLANLEAKY_OFFSET    4
-#define    RTL8367C_RRCP_VLANLEAKY_MASK    0x10
-#define    RTL8367C_RRCPV1_SECURITY_CRC_GET_OFFSET    3
-#define    RTL8367C_RRCPV1_SECURITY_CRC_GET_MASK    0x8
-#define    RTL8367C_RRCPV1_SECURITY_CRC_SET_OFFSET    2
-#define    RTL8367C_RRCPV1_SECURITY_CRC_SET_MASK    0x4
-#define    RTL8367C_RRCPV1_HANDLE_OFFSET    1
-#define    RTL8367C_RRCPV1_HANDLE_MASK    0x2
-#define    RTL8367C_RRCP_ENABLE_OFFSET    0
-#define    RTL8367C_RRCP_ENABLE_MASK    0x1
-
-#define    RTL8367C_REG_RRCP_CTRL1    0x122c
-#define    RTL8367C_RRCP_ADMIN_PMSK_OFFSET    8
-#define    RTL8367C_RRCP_ADMIN_PMSK_MASK    0xFF00
-#define    RTL8367C_RRCP_AUTH_PMSK_OFFSET    0
-#define    RTL8367C_RRCP_AUTH_PMSK_MASK    0xFF
-
-#define    RTL8367C_REG_RRCP_CTRL2    0x122d
-#define    RTL8367C_RRCPV1_HELLOFWD_TAG_OFFSET    9
-#define    RTL8367C_RRCPV1_HELLOFWD_TAG_MASK    0x600
-#define    RTL8367C_RRCP_FWD_TAG_OFFSET    7
-#define    RTL8367C_RRCP_FWD_TAG_MASK    0x180
-#define    RTL8367C_RRCPV1_REPLY_TAG_OFFSET    6
-#define    RTL8367C_RRCPV1_REPLY_TAG_MASK    0x40
-#define    RTL8367C_RRCPV1_HELLO_COUNT_OFFSET    3
-#define    RTL8367C_RRCPV1_HELLO_COUNT_MASK    0x38
-#define    RTL8367C_RRCPV1_HELLO_PEDIOD_OFFSET    0
-#define    RTL8367C_RRCPV1_HELLO_PEDIOD_MASK    0x3
-
-#define    RTL8367C_REG_RRCP_CTRL3    0x122e
-#define    RTL8367C_RRCP_TAG_PRIORITY_OFFSET    13
-#define    RTL8367C_RRCP_TAG_PRIORITY_MASK    0xE000
-#define    RTL8367C_RRCP_TAG_VID_OFFSET    0
-#define    RTL8367C_RRCP_TAG_VID_MASK    0xFFF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_PORT_ON    0x122f
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_PORT_OFF    0x1230
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_PORT_PRIVATE_ON    0x1231
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_FCOFF_PORT_PRIVATE_OFF    0x1232
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_SYS_ON    0x1233
-#define    RTL8367C_FLOWCTRL_JUMBO_SYS_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_SYS_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_SYS_OFF    0x1234
-#define    RTL8367C_FLOWCTRL_JUMBO_SYS_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_SYS_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_SHARE_ON    0x1235
-#define    RTL8367C_FLOWCTRL_JUMBO_SHARE_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_SHARE_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_SHARE_OFF    0x1236
-#define    RTL8367C_FLOWCTRL_JUMBO_SHARE_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_SHARE_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_PORT_ON    0x1237
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_PORT_OFF    0x1238
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_ON    0x1239
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_ON_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_ON_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF    0x123a
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF_OFFSET    0
-#define    RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_JUMBO_SIZE    0x123b
-#define    RTL8367C_JUMBO_MODE_OFFSET    2
-#define    RTL8367C_JUMBO_MODE_MASK    0x4
-#define    RTL8367C_JUMBO_SIZE_OFFSET    0
-#define    RTL8367C_JUMBO_SIZE_MASK    0x3
-
-#define    RTL8367C_REG_FLOWCTRL_TOTAL_PAGE_COUNTER    0x124c
-#define    RTL8367C_FLOWCTRL_TOTAL_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_TOTAL_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PUBLIC_PAGE_COUNTER    0x124d
-#define    RTL8367C_FLOWCTRL_PUBLIC_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PUBLIC_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_TOTAL_PAGE_MAX    0x124e
-#define    RTL8367C_FLOWCTRL_TOTAL_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_TOTAL_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PUBLIC_PAGE_MAX    0x124f
-#define    RTL8367C_FLOWCTRL_PUBLIC_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PUBLIC_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT0_PAGE_COUNTER    0x1250
-#define    RTL8367C_FLOWCTRL_PORT0_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT0_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT1_PAGE_COUNTER    0x1251
-#define    RTL8367C_FLOWCTRL_PORT1_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT1_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT2_PAGE_COUNTER    0x1252
-#define    RTL8367C_FLOWCTRL_PORT2_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT2_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT3_PAGE_COUNTER    0x1253
-#define    RTL8367C_FLOWCTRL_PORT3_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT3_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT4_PAGE_COUNTER    0x1254
-#define    RTL8367C_FLOWCTRL_PORT4_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT4_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT5_PAGE_COUNTER    0x1255
-#define    RTL8367C_FLOWCTRL_PORT5_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT5_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT6_PAGE_COUNTER    0x1256
-#define    RTL8367C_FLOWCTRL_PORT6_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT6_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT7_PAGE_COUNTER    0x1257
-#define    RTL8367C_FLOWCTRL_PORT7_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT7_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PUBLIC_FCOFF_PAGE_COUNTER    0x1258
-#define    RTL8367C_FLOWCTRL_PUBLIC_FCOFF_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PUBLIC_FCOFF_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PUBLIC_JUMBO_PAGE_COUNTER    0x1259
-#define    RTL8367C_FLOWCTRL_PUBLIC_JUMBO_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PUBLIC_JUMBO_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_MAX_PUBLIC_FCOFF_PAGE_COUNTER    0x125a
-#define    RTL8367C_FLOWCTRL_MAX_PUBLIC_FCOFF_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_MAX_PUBLIC_FCOFF_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_MAX_PUBLIC_JUMBO_PAGE_COUNTER    0x125b
-#define    RTL8367C_FLOWCTRL_MAX_PUBLIC_JUMBO_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_MAX_PUBLIC_JUMBO_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT0_PAGE_MAX    0x1260
-#define    RTL8367C_FLOWCTRL_PORT0_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT0_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT1_PAGE_MAX    0x1261
-#define    RTL8367C_FLOWCTRL_PORT1_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT1_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT2_PAGE_MAX    0x1262
-#define    RTL8367C_FLOWCTRL_PORT2_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT2_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT3_PAGE_MAX    0x1263
-#define    RTL8367C_FLOWCTRL_PORT3_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT3_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT4_PAGE_MAX    0x1264
-#define    RTL8367C_FLOWCTRL_PORT4_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT4_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT5_PAGE_MAX    0x1265
-#define    RTL8367C_FLOWCTRL_PORT5_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT5_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT6_PAGE_MAX    0x1266
-#define    RTL8367C_FLOWCTRL_PORT6_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT6_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT7_PAGE_MAX    0x1267
-#define    RTL8367C_FLOWCTRL_PORT7_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT7_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PAGE_COUNT_CLEAR    0x1268
-#define    RTL8367C_DIS_SKIP_FP_OFFSET    1
-#define    RTL8367C_DIS_SKIP_FP_MASK    0x2
-#define    RTL8367C_PAGE_COUNT_CLEAR_OFFSET    0
-#define    RTL8367C_PAGE_COUNT_CLEAR_MASK    0x1
-
-#define    RTL8367C_REG_FLOWCTRL_PORT8_PAGE_MAX    0x1269
-#define    RTL8367C_FLOWCTRL_PORT8_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT8_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT9_PAGE_MAX    0x126a
-#define    RTL8367C_FLOWCTRL_PORT9_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT9_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT10_PAGE_MAX    0x126b
-#define    RTL8367C_FLOWCTRL_PORT10_PAGE_MAX_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT10_PAGE_MAX_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT8_PAGE_COUNTER    0x126c
-#define    RTL8367C_FLOWCTRL_PORT8_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT8_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT9_PAGE_COUNTER    0x126d
-#define    RTL8367C_FLOWCTRL_PORT9_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT9_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_FLOWCTRL_PORT10_PAGE_COUNTER    0x126e
-#define    RTL8367C_FLOWCTRL_PORT10_PAGE_COUNTER_OFFSET    0
-#define    RTL8367C_FLOWCTRL_PORT10_PAGE_COUNTER_MASK    0x7FF
-
-#define    RTL8367C_REG_RRCP_CTRL1_H    0x126f
-#define    RTL8367C_RRCP_ADMIN_PMSK_P10_8_OFFSET    3
-#define    RTL8367C_RRCP_ADMIN_PMSK_P10_8_MASK    0x38
-#define    RTL8367C_RRCP_AUTH_PMSK_P10_8_OFFSET    0
-#define    RTL8367C_RRCP_AUTH_PMSK_P10_8_MASK    0x7
-
-#define    RTL8367C_REG_EMA_CTRL0    0x1270
-#define    RTL8367C_CFG_DVSE_VIAROM_OFFSET    13
-#define    RTL8367C_CFG_DVSE_VIAROM_MASK    0x2000
-#define    RTL8367C_CFG_DVSE_MIBRAM_OFFSET    12
-#define    RTL8367C_CFG_DVSE_MIBRAM_MASK    0x1000
-#define    RTL8367C_CFG_DVSE_IROM_OFFSET    11
-#define    RTL8367C_CFG_DVSE_IROM_MASK    0x800
-#define    RTL8367C_CFG_DVSE_ERAM_OFFSET    10
-#define    RTL8367C_CFG_DVSE_ERAM_MASK    0x400
-#define    RTL8367C_CFG_DVSE_IRAM_OFFSET    9
-#define    RTL8367C_CFG_DVSE_IRAM_MASK    0x200
-#define    RTL8367C_CFG_DVSE_NICRAM_OFFSET    8
-#define    RTL8367C_CFG_DVSE_NICRAM_MASK    0x100
-#define    RTL8367C_CFG_DVSE_CVLANRAM_OFFSET    7
-#define    RTL8367C_CFG_DVSE_CVLANRAM_MASK    0x80
-#define    RTL8367C_CFG_DVSE_ACTRAM_OFFSET    6
-#define    RTL8367C_CFG_DVSE_ACTRAM_MASK    0x40
-#define    RTL8367C_CFG_DVSE_INQRAM_OFFSET    5
-#define    RTL8367C_CFG_DVSE_INQRAM_MASK    0x20
-#define    RTL8367C_CFG_DVSE_HSARAM_OFFSET    4
-#define    RTL8367C_CFG_DVSE_HSARAM_MASK    0x10
-#define    RTL8367C_CFG_DVSE_OUTQRAM_OFFSET    3
-#define    RTL8367C_CFG_DVSE_OUTQRAM_MASK    0x8
-#define    RTL8367C_CFG_DVSE_HTRAM_OFFSET    2
-#define    RTL8367C_CFG_DVSE_HTRAM_MASK    0x4
-#define    RTL8367C_CFG_DVSE_PBRAM_OFFSET    1
-#define    RTL8367C_CFG_DVSE_PBRAM_MASK    0x2
-#define    RTL8367C_CFG_DVSE_L2RAM_OFFSET    0
-#define    RTL8367C_CFG_DVSE_L2RAM_MASK    0x1
-
-#define    RTL8367C_REG_EMA_CTRL1    0x1271
-#define    RTL8367C_CFG_DVS_OUTQRAM_OFFSET    12
-#define    RTL8367C_CFG_DVS_OUTQRAM_MASK    0xF000
-#define    RTL8367C_CFG_DVS_HTRAM_OFFSET    8
-#define    RTL8367C_CFG_DVS_HTRAM_MASK    0x700
-#define    RTL8367C_CFG_DVS_PBRAM_OFFSET    4
-#define    RTL8367C_CFG_DVS_PBRAM_MASK    0xF0
-#define    RTL8367C_CFG_DVS_L2RAM_OFFSET    0
-#define    RTL8367C_CFG_DVS_L2RAM_MASK    0xF
-
-#define    RTL8367C_REG_EMA_CTRL2    0x1272
-#define    RTL8367C_CFG_DVS_CVLANRAM_OFFSET    12
-#define    RTL8367C_CFG_DVS_CVLANRAM_MASK    0xF000
-#define    RTL8367C_CFG_DVS_ACTRAM_OFFSET    8
-#define    RTL8367C_CFG_DVS_ACTRAM_MASK    0xF00
-#define    RTL8367C_CFG_DVS_INQRAM_OFFSET    4
-#define    RTL8367C_CFG_DVS_INQRAM_MASK    0xF0
-#define    RTL8367C_CFG_DVS_HSARAM_OFFSET    0
-#define    RTL8367C_CFG_DVS_HSARAM_MASK    0xF
-
-#define    RTL8367C_REG_EMA_CTRL3    0x1273
-#define    RTL8367C_CFG_DVS_IROM_OFFSET    12
-#define    RTL8367C_CFG_DVS_IROM_MASK    0xF000
-#define    RTL8367C_CFG_DVS_ERAM_OFFSET    8
-#define    RTL8367C_CFG_DVS_ERAM_MASK    0xF00
-#define    RTL8367C_CFG_DVS_IRAM_OFFSET    4
-#define    RTL8367C_CFG_DVS_IRAM_MASK    0xF0
-#define    RTL8367C_CFG_DVS_NICRAM_OFFSET    0
-#define    RTL8367C_CFG_DVS_NICRAM_MASK    0xF
-
-#define    RTL8367C_REG_EMA_CTRL4    0x1274
-#define    RTL8367C_CFG_DVS_VIAROM_OFFSET    4
-#define    RTL8367C_CFG_DVS_VIAROM_MASK    0xF0
-#define    RTL8367C_CFG_DVS_MIBRAM_OFFSET    0
-#define    RTL8367C_CFG_DVS_MIBRAM_MASK    0xF
-
-#define    RTL8367C_REG_DIAG_MODE    0x1275
-#define    RTL8367C_DIAG_MODE_OFFSET    0
-#define    RTL8367C_DIAG_MODE_MASK    0x1F
-
-#define    RTL8367C_REG_BIST_MODE    0x1276
-
-#define    RTL8367C_REG_STS_BIST_DONE    0x1277
-
-#define    RTL8367C_REG_STS_BIST_RLT0    0x1278
-#define    RTL8367C_STS_BIST_RLT0_OFFSET    0
-#define    RTL8367C_STS_BIST_RLT0_MASK    0x1
-
-#define    RTL8367C_REG_STS_BIST_RLT1    0x1279
-
-#define    RTL8367C_REG_STS_BIST_RLT2    0x127a
-
-#define    RTL8367C_REG_STS_BIST_RLT3    0x127b
-#define    RTL8367C_STS_BIST_RLT3_OFFSET    0
-#define    RTL8367C_STS_BIST_RLT3_MASK    0x3FF
-
-#define    RTL8367C_REG_STS_BIST_RLT4    0x127c
-#define    RTL8367C_STS_BIST_RLT4_OFFSET    0
-#define    RTL8367C_STS_BIST_RLT4_MASK    0x7
-
-#define    RTL8367C_REG_VIAROM_MISR    0x127d
-
-#define    RTL8367C_REG_DRF_BIST_MODE    0x1280
-#define    RTL8367C_DRF_TCAMDEL_OFFSET    15
-#define    RTL8367C_DRF_TCAMDEL_MASK    0x8000
-#define    RTL8367C_CFG_DRF_BIST_MODE_OFFSET    0
-#define    RTL8367C_CFG_DRF_BIST_MODE_MASK    0x7FFF
-
-#define    RTL8367C_REG_STS_DRF_BIST    0x1281
-#define    RTL8367C_STS_DRF_BIST_OFFSET    0
-#define    RTL8367C_STS_DRF_BIST_MASK    0x7FFF
-
-#define    RTL8367C_REG_STS_DRF_BIST_RLT0    0x1282
-#define    RTL8367C_STS_DRF_BIST_RLT0_OFFSET    0
-#define    RTL8367C_STS_DRF_BIST_RLT0_MASK    0x1
-
-#define    RTL8367C_REG_STS_DRF_BIST_RLT1    0x1283
-
-#define    RTL8367C_REG_STS_DRF_BIST_RLT2    0x1284
-
-#define    RTL8367C_REG_STS_DRF_BIST_RLT3    0x1285
-#define    RTL8367C_STS_DRF_BIST_RLT3_OFFSET    0
-#define    RTL8367C_STS_DRF_BIST_RLT3_MASK    0x3FF
-
-#define    RTL8367C_REG_STS_DRF_BIST_RLT4    0x1286
-#define    RTL8367C_STS_DRF_BIST_RLT4_OFFSET    0
-#define    RTL8367C_STS_DRF_BIST_RLT4_MASK    0x7FFF
-
-#define    RTL8367C_REG_RAM_DRF_CTRL    0x1289
-#define    RTL8367C_RAM_DRF_CTRL_OFFSET    0
-#define    RTL8367C_RAM_DRF_CTRL_MASK    0x1
-
-#define    RTL8367C_REG_MIB_RMON_LEN_CTRL    0x128a
-#define    RTL8367C_RX_LENGTH_CTRL_OFFSET    1
-#define    RTL8367C_RX_LENGTH_CTRL_MASK    0x2
-#define    RTL8367C_TX_LENGTH_CTRL_OFFSET    0
-#define    RTL8367C_TX_LENGTH_CTRL_MASK    0x1
-
-#define    RTL8367C_REG_COND0_BISR_OUT0    0x1290
-
-#define    RTL8367C_REG_COND0_BISR_OUT1    0x1291
-
-#define    RTL8367C_REG_COND0_BISR_OUT2    0x1292
-
-#define    RTL8367C_REG_COND0_BISR_OUT3    0x1293
-
-#define    RTL8367C_REG_COND0_BISR_OUT4    0x1294
-#define    RTL8367C_COND0_BISR_OUT4_OFFSET    0
-#define    RTL8367C_COND0_BISR_OUT4_MASK    0x3F
-
-#define    RTL8367C_REG_COND0_BISR_OUT5    0x1295
-#define    RTL8367C_COND0_BISR_OUT5_OFFSET    0
-#define    RTL8367C_COND0_BISR_OUT5_MASK    0x7
-
-#define    RTL8367C_REG_CHG_DUPLEX_CFG    0x1296
-#define    RTL8367C_CHG_COL_CNT_PORT_OFFSET    13
-#define    RTL8367C_CHG_COL_CNT_PORT_MASK    0xE000
-#define    RTL8367C_CHG_COL_CNT_OFFSET    8
-#define    RTL8367C_CHG_COL_CNT_MASK    0x1F00
-#define    RTL8367C_CFG_CHG_DUP_EN_OFFSET    7
-#define    RTL8367C_CFG_CHG_DUP_EN_MASK    0x80
-#define    RTL8367C_CFG_CHG_DUP_THR_OFFSET    2
-#define    RTL8367C_CFG_CHG_DUP_THR_MASK    0x7C
-#define    RTL8367C_CFG_CHG_DUP_CONGEST_OFFSET    1
-#define    RTL8367C_CFG_CHG_DUP_CONGEST_MASK    0x2
-#define    RTL8367C_CFG_CHG_DUP_REF_OFFSET    0
-#define    RTL8367C_CFG_CHG_DUP_REF_MASK    0x1
-
-#define    RTL8367C_REG_COND0_BIST_PASS    0x1297
-#define    RTL8367C_COND0_DRF_BIST_NOFAIL_OFFSET    1
-#define    RTL8367C_COND0_DRF_BIST_NOFAIL_MASK    0x2
-#define    RTL8367C_COND0_BIST_NOFAIL_OFFSET    0
-#define    RTL8367C_COND0_BIST_NOFAIL_MASK    0x1
-
-#define    RTL8367C_REG_COND1_BISR_OUT0    0x1298
-
-#define    RTL8367C_REG_COND1_BISR_OUT1    0x1299
-
-#define    RTL8367C_REG_COND1_BISR_OUT2    0x129a
-
-#define    RTL8367C_REG_COND1_BISR_OUT3    0x129b
-
-#define    RTL8367C_REG_COND1_BISR_OUT4    0x129c
-#define    RTL8367C_COND1_BISR_OUT4_OFFSET    0
-#define    RTL8367C_COND1_BISR_OUT4_MASK    0x3F
-
-#define    RTL8367C_REG_COND1_BISR_OUT5    0x129d
-#define    RTL8367C_COND1_BISR_OUT5_OFFSET    0
-#define    RTL8367C_COND1_BISR_OUT5_MASK    0x7
-
-#define    RTL8367C_REG_COND1_BIST_PASS    0x129f
-#define    RTL8367C_COND1_DRF_BIST_NOFAIL_OFFSET    1
-#define    RTL8367C_COND1_DRF_BIST_NOFAIL_MASK    0x2
-#define    RTL8367C_COND1_BIST_NOFAIL_OFFSET    0
-#define    RTL8367C_COND1_BIST_NOFAIL_MASK    0x1
-
-#define    RTL8367C_REG_EEE_TX_THR_Giga_500M    0x12a0
-
-#define    RTL8367C_REG_EEE_TX_THR_FE    0x12a1
-
-#define    RTL8367C_REG_EEE_MISC    0x12a3
-#define    RTL8367C_EEE_REQ_SET1_OFFSET    13
-#define    RTL8367C_EEE_REQ_SET1_MASK    0x2000
-#define    RTL8367C_EEE_REQ_SET0_OFFSET    12
-#define    RTL8367C_EEE_REQ_SET0_MASK    0x1000
-#define    RTL8367C_EEE_WAKE_SET1_OFFSET    9
-#define    RTL8367C_EEE_WAKE_SET1_MASK    0x200
-#define    RTL8367C_EEE_Wake_SET0_OFFSET    8
-#define    RTL8367C_EEE_Wake_SET0_MASK    0x100
-#define    RTL8367C_EEE_TU_GIGA_500M_OFFSET    4
-#define    RTL8367C_EEE_TU_GIGA_500M_MASK    0x30
-#define    RTL8367C_EEE_TU_100M_OFFSET    2
-#define    RTL8367C_EEE_TU_100M_MASK    0xC
-
-#define    RTL8367C_REG_EEE_GIGA_CTRL0    0x12a4
-#define    RTL8367C_EEE_TW_GIGA_OFFSET    8
-#define    RTL8367C_EEE_TW_GIGA_MASK    0xFF00
-#define    RTL8367C_EEE_TR_GIGA_500M_OFFSET    0
-#define    RTL8367C_EEE_TR_GIGA_500M_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_GIGA_CTRL1    0x12a5
-#define    RTL8367C_EEE_TD_GIGA_500M_OFFSET    8
-#define    RTL8367C_EEE_TD_GIGA_500M_MASK    0xFF00
-#define    RTL8367C_EEE_TP_GIGA_OFFSET    0
-#define    RTL8367C_EEE_TP_GIGA_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_100M_CTRL0    0x12a6
-#define    RTL8367C_EEE_TW_100M_OFFSET    8
-#define    RTL8367C_EEE_TW_100M_MASK    0xFF00
-#define    RTL8367C_EEE_TR_100M_OFFSET    0
-#define    RTL8367C_EEE_TR_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_100M_CTRL1    0x12a7
-#define    RTL8367C_EEE_TD_100M_OFFSET    8
-#define    RTL8367C_EEE_TD_100M_MASK    0xFF00
-#define    RTL8367C_EEE_TP_100M_OFFSET    0
-#define    RTL8367C_EEE_TP_100M_MASK    0xFF
-
-#define    RTL8367C_REG_RX_FC_REG    0x12aa
-#define    RTL8367C_EN_EEE_HALF_DUP_OFFSET    8
-#define    RTL8367C_EN_EEE_HALF_DUP_MASK    0x100
-#define    RTL8367C_RX_PGCNT_OFFSET    0
-#define    RTL8367C_RX_PGCNT_MASK    0xFF
-
-#define    RTL8367C_REG_MAX_FIFO_SIZE    0x12af
-#define    RTL8367C_MAX_FIFO_SIZE_OFFSET    0
-#define    RTL8367C_MAX_FIFO_SIZE_MASK    0xF
-
-#define    RTL8367C_REG_EEEP_RX_RATE_GIGA    0x12b0
-
-#define    RTL8367C_REG_EEEP_RX_RATE_100M    0x12b1
-
-#define    RTL8367C_REG_DUMMY_REG_12_2    0x12b2
-
-#define    RTL8367C_REG_EEEP_TX_RATE_GIGA    0x12b3
-
-#define    RTL8367C_REG_EEEP_TX_RATE_100M    0x12b4
-
-#define    RTL8367C_REG_DUMMY_REG_12_3    0x12b5
-
-#define    RTL8367C_REG_EEEP_GIGA_CTRL0    0x12b6
-#define    RTL8367C_EEEP_TR_GIGA_OFFSET    8
-#define    RTL8367C_EEEP_TR_GIGA_MASK    0xFF00
-#define    RTL8367C_EEEP_RW_GIGA_MST_OFFSET    0
-#define    RTL8367C_EEEP_RW_GIGA_MST_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_GIGA_CTRL1    0x12b7
-#define    RTL8367C_EEEP_TW_GIGA_OFFSET    8
-#define    RTL8367C_EEEP_TW_GIGA_MASK    0xFF00
-#define    RTL8367C_EEEP_TP_GIGA_OFFSET    0
-#define    RTL8367C_EEEP_TP_GIGA_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_GIGA_CTRL2    0x12b8
-#define    RTL8367C_EEEP_TXEN_GIGA_OFFSET    12
-#define    RTL8367C_EEEP_TXEN_GIGA_MASK    0x1000
-#define    RTL8367C_EEEP_TU_GIGA_OFFSET    8
-#define    RTL8367C_EEEP_TU_GIGA_MASK    0x300
-#define    RTL8367C_EEEP_TS_GIGA_OFFSET    0
-#define    RTL8367C_EEEP_TS_GIGA_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_100M_CTRL0    0x12b9
-#define    RTL8367C_EEEP_TR_100M_OFFSET    8
-#define    RTL8367C_EEEP_TR_100M_MASK    0xFF00
-#define    RTL8367C_EEEP_RW_100M_OFFSET    0
-#define    RTL8367C_EEEP_RW_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_100M_CTRL1    0x12ba
-#define    RTL8367C_EEEP_TW_100M_OFFSET    8
-#define    RTL8367C_EEEP_TW_100M_MASK    0xFF00
-#define    RTL8367C_EEEP_TP_100M_OFFSET    0
-#define    RTL8367C_EEEP_TP_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_100M_CTRL2    0x12bb
-#define    RTL8367C_EEEP_TXEN_100M_OFFSET    12
-#define    RTL8367C_EEEP_TXEN_100M_MASK    0x1000
-#define    RTL8367C_EEEP_TU_100M_OFFSET    8
-#define    RTL8367C_EEEP_TU_100M_MASK    0x300
-#define    RTL8367C_EEEP_TS_100M_OFFSET    0
-#define    RTL8367C_EEEP_TS_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_CTRL0    0x12bc
-#define    RTL8367C_EEEP_CTRL0_DUMMY_OFFSET    8
-#define    RTL8367C_EEEP_CTRL0_DUMMY_MASK    0xFF00
-#define    RTL8367C_EEEP_SLEEP_STEP_OFFSET    0
-#define    RTL8367C_EEEP_SLEEP_STEP_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_CTRL1    0x12bd
-#define    RTL8367C_EEEP_TXR_GIGA_OFFSET    8
-#define    RTL8367C_EEEP_TXR_GIGA_MASK    0xFF00
-#define    RTL8367C_EEEP_TXR_100M_OFFSET    0
-#define    RTL8367C_EEEP_TXR_100M_MASK    0xFF
-
-#define    RTL8367C_REG_BACK_PRESSURE_IPG    0x12be
-#define    RTL8367C_BACK_PRESSURE_IPG_OFFSET    0
-#define    RTL8367C_BACK_PRESSURE_IPG_MASK    0x3
-
-#define    RTL8367C_REG_TX_ESD_LEVEL    0x12bf
-#define    RTL8367C_TX_ESD_LEVEL_MODE_OFFSET    8
-#define    RTL8367C_TX_ESD_LEVEL_MODE_MASK    0x100
-#define    RTL8367C_LEVEL_OFFSET    0
-#define    RTL8367C_LEVEL_MASK    0xFF
-
-#define    RTL8367C_REG_RRCP_CTRL4    0x12e0
-
-#define    RTL8367C_REG_RRCP_CTRL5    0x12e1
-
-#define    RTL8367C_REG_RRCP_CTRL6    0x12e2
-
-#define    RTL8367C_REG_RRCP_CTRL7    0x12e3
-
-#define    RTL8367C_REG_RRCP_CTRL8    0x12e4
-
-#define    RTL8367C_REG_RRCP_CTRL9    0x12e5
-
-#define    RTL8367C_REG_RRCP_CTRL10    0x12e6
-
-#define    RTL8367C_REG_FIELD_SELECTOR0    0x12e7
-#define    RTL8367C_FIELD_SELECTOR0_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR0_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR0_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR0_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR1    0x12e8
-#define    RTL8367C_FIELD_SELECTOR1_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR1_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR1_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR1_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR2    0x12e9
-#define    RTL8367C_FIELD_SELECTOR2_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR2_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR2_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR2_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR3    0x12ea
-#define    RTL8367C_FIELD_SELECTOR3_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR3_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR3_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR3_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR4    0x12eb
-#define    RTL8367C_FIELD_SELECTOR4_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR4_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR4_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR4_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR5    0x12ec
-#define    RTL8367C_FIELD_SELECTOR5_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR5_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR5_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR5_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR6    0x12ed
-#define    RTL8367C_FIELD_SELECTOR6_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR6_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR6_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR6_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR7    0x12ee
-#define    RTL8367C_FIELD_SELECTOR7_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR7_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR7_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR7_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR8    0x12ef
-#define    RTL8367C_FIELD_SELECTOR8_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR8_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR8_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR8_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR9    0x12f0
-#define    RTL8367C_FIELD_SELECTOR9_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR9_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR9_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR9_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR10    0x12f1
-#define    RTL8367C_FIELD_SELECTOR10_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR10_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR10_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR10_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR11    0x12f2
-#define    RTL8367C_FIELD_SELECTOR11_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR11_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR11_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR11_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR12    0x12f3
-#define    RTL8367C_FIELD_SELECTOR12_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR12_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR12_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR12_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR13    0x12f4
-#define    RTL8367C_FIELD_SELECTOR13_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR13_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR13_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR13_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR14    0x12f5
-#define    RTL8367C_FIELD_SELECTOR14_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR14_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR14_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR14_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_FIELD_SELECTOR15    0x12f6
-#define    RTL8367C_FIELD_SELECTOR15_FORMAT_OFFSET    8
-#define    RTL8367C_FIELD_SELECTOR15_FORMAT_MASK    0x700
-#define    RTL8367C_FIELD_SELECTOR15_OFFSET_OFFSET    0
-#define    RTL8367C_FIELD_SELECTOR15_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_HWPKT_GEN_MISC_H    0x12f7
-#define    RTL8367C_PKT_GEN_SUSPEND_P10_8_OFFSET    3
-#define    RTL8367C_PKT_GEN_SUSPEND_P10_8_MASK    0x38
-#define    RTL8367C_PKT_GEN_STATUS_P10_8_OFFSET    0
-#define    RTL8367C_PKT_GEN_STATUS_P10_8_MASK    0x7
-
-#define    RTL8367C_REG_MIRROR_SRC_PMSK    0x12fb
-#define    RTL8367C_MIRROR_SRC_PMSK_OFFSET    0
-#define    RTL8367C_MIRROR_SRC_PMSK_MASK    0x7FF
-
-#define    RTL8367C_REG_EEE_BURSTSIZE    0x12fc
-
-#define    RTL8367C_REG_EEE_IFG_CFG    0x12fd
-#define    RTL8367C_EEE_IFG_CFG_OFFSET    0
-#define    RTL8367C_EEE_IFG_CFG_MASK    0x1
-
-#define    RTL8367C_REG_FPGA_VER_MAC    0x12fe
-
-#define    RTL8367C_REG_HWPKT_GEN_MISC    0x12ff
-#define    RTL8367C_PKT_GEN_SUSPEND_OFFSET    8
-#define    RTL8367C_PKT_GEN_SUSPEND_MASK    0xFF00
-#define    RTL8367C_PKT_GEN_STATUS_OFFSET    0
-#define    RTL8367C_PKT_GEN_STATUS_MASK    0xFF
-
-/* (16'h1300)chip_reg */
-
-#define    RTL8367C_REG_CHIP_NUMBER    0x1300
-
-#define    RTL8367C_REG_CHIP_VER    0x1301
-#define    RTL8367C_VERID_OFFSET    12
-#define    RTL8367C_VERID_MASK    0xF000
-#define    RTL8367C_MCID_OFFSET    8
-#define    RTL8367C_MCID_MASK    0xF00
-#define    RTL8367C_MODEL_ID_OFFSET    4
-#define    RTL8367C_MODEL_ID_MASK    0xF0
-#define    RTL8367C_AFE_VERSION_OFFSET    0
-#define    RTL8367C_AFE_VERSION_MASK    0x1
-
-#define    RTL8367C_REG_CHIP_DEBUG0    0x1303
-#define    RTL8367C_SEL33_EXT2_OFFSET    10
-#define    RTL8367C_SEL33_EXT2_MASK    0x400
-#define    RTL8367C_SEL33_EXT1_OFFSET    9
-#define    RTL8367C_SEL33_EXT1_MASK    0x200
-#define    RTL8367C_SEL33_EXT0_OFFSET    8
-#define    RTL8367C_SEL33_EXT0_MASK    0x100
-#define    RTL8367C_DRI_OTHER_OFFSET    7
-#define    RTL8367C_DRI_OTHER_MASK    0x80
-#define    RTL8367C_DRI_EXT1_RG_OFFSET    6
-#define    RTL8367C_DRI_EXT1_RG_MASK    0x40
-#define    RTL8367C_DRI_EXT0_RG_OFFSET    5
-#define    RTL8367C_DRI_EXT0_RG_MASK    0x20
-#define    RTL8367C_DRI_EXT1_OFFSET    4
-#define    RTL8367C_DRI_EXT1_MASK    0x10
-#define    RTL8367C_DRI_EXT0_OFFSET    3
-#define    RTL8367C_DRI_EXT0_MASK    0x8
-#define    RTL8367C_SLR_OTHER_OFFSET    2
-#define    RTL8367C_SLR_OTHER_MASK    0x4
-#define    RTL8367C_SLR_EXT1_OFFSET    1
-#define    RTL8367C_SLR_EXT1_MASK    0x2
-#define    RTL8367C_SLR_EXT0_OFFSET    0
-#define    RTL8367C_SLR_EXT0_MASK    0x1
-
-#define    RTL8367C_REG_CHIP_DEBUG1    0x1304
-#define    RTL8367C_RG1_DN_OFFSET    12
-#define    RTL8367C_RG1_DN_MASK    0x7000
-#define    RTL8367C_RG1_DP_OFFSET    8
-#define    RTL8367C_RG1_DP_MASK    0x700
-#define    RTL8367C_RG0_DN_OFFSET    4
-#define    RTL8367C_RG0_DN_MASK    0x70
-#define    RTL8367C_RG0_DP_OFFSET    0
-#define    RTL8367C_RG0_DP_MASK    0x7
-
-#define    RTL8367C_REG_DIGITAL_INTERFACE_SELECT    0x1305
-#define    RTL8367C_ORG_COL_OFFSET    15
-#define    RTL8367C_ORG_COL_MASK    0x8000
-#define    RTL8367C_ORG_CRS_OFFSET    14
-#define    RTL8367C_ORG_CRS_MASK    0x4000
-#define    RTL8367C_SKIP_MII_1_RXER_OFFSET    13
-#define    RTL8367C_SKIP_MII_1_RXER_MASK    0x2000
-#define    RTL8367C_SKIP_MII_0_RXER_OFFSET    12
-#define    RTL8367C_SKIP_MII_0_RXER_MASK    0x1000
-#define    RTL8367C_SELECT_GMII_1_OFFSET    4
-#define    RTL8367C_SELECT_GMII_1_MASK    0xF0
-#define    RTL8367C_SELECT_GMII_0_OFFSET    0
-#define    RTL8367C_SELECT_GMII_0_MASK    0xF
-
-#define    RTL8367C_REG_EXT0_RGMXF    0x1306
-#define    RTL8367C_EXT0_RGTX_INV_OFFSET    6
-#define    RTL8367C_EXT0_RGTX_INV_MASK    0x40
-#define    RTL8367C_EXT0_RGRX_INV_OFFSET    5
-#define    RTL8367C_EXT0_RGRX_INV_MASK    0x20
-#define    RTL8367C_EXT0_RGMXF_OFFSET    0
-#define    RTL8367C_EXT0_RGMXF_MASK    0x1F
-
-#define    RTL8367C_REG_EXT1_RGMXF    0x1307
-#define    RTL8367C_EXT1_RGTX_INV_OFFSET    6
-#define    RTL8367C_EXT1_RGTX_INV_MASK    0x40
-#define    RTL8367C_EXT1_RGRX_INV_OFFSET    5
-#define    RTL8367C_EXT1_RGRX_INV_MASK    0x20
-#define    RTL8367C_EXT1_RGMXF_OFFSET    0
-#define    RTL8367C_EXT1_RGMXF_MASK    0x1F
-
-#define    RTL8367C_REG_BISR_CTRL    0x1308
-#define    RTL8367C_BISR_CTRL_OFFSET    0
-#define    RTL8367C_BISR_CTRL_MASK    0x7
-
-#define    RTL8367C_REG_SLF_IF    0x1309
-#define    RTL8367C_LINK_DOWN_CLR_FIFO_OFFSET    7
-#define    RTL8367C_LINK_DOWN_CLR_FIFO_MASK    0x80
-#define    RTL8367C_LOOPBACK_OFFSET    6
-#define    RTL8367C_LOOPBACK_MASK    0x40
-#define    RTL8367C_WATER_LEVEL_OFFSET    4
-#define    RTL8367C_WATER_LEVEL_MASK    0x30
-#define    RTL8367C_SLF_IF_OFFSET    0
-#define    RTL8367C_SLF_IF_MASK    0x3
-
-#define    RTL8367C_REG_I2C_CLOCK_DIV    0x130a
-#define    RTL8367C_I2C_CLOCK_DIV_OFFSET    0
-#define    RTL8367C_I2C_CLOCK_DIV_MASK    0x3FF
-
-#define    RTL8367C_REG_MDX_MDC_DIV    0x130b
-#define    RTL8367C_MDX_MDC_DIV_OFFSET    0
-#define    RTL8367C_MDX_MDC_DIV_MASK    0x3FF
-
-#define    RTL8367C_REG_MISCELLANEOUS_CONFIGURE0    0x130c
-#define    RTL8367C_ADCCKI_FROM_PAD_OFFSET    14
-#define    RTL8367C_ADCCKI_FROM_PAD_MASK    0x4000
-#define    RTL8367C_ADCCKI_EN_OFFSET    13
-#define    RTL8367C_ADCCKI_EN_MASK    0x2000
-#define    RTL8367C_FLASH_ENABLE_OFFSET    12
-#define    RTL8367C_FLASH_ENABLE_MASK    0x1000
-#define    RTL8367C_EEE_ENABLE_OFFSET    11
-#define    RTL8367C_EEE_ENABLE_MASK    0x800
-#define    RTL8367C_NIC_ENABLE_OFFSET    10
-#define    RTL8367C_NIC_ENABLE_MASK    0x400
-#define    RTL8367C_FT_ENABLE_OFFSET    9
-#define    RTL8367C_FT_ENABLE_MASK    0x200
-#define    RTL8367C_OLT_ENABLE_OFFSET    8
-#define    RTL8367C_OLT_ENABLE_MASK    0x100
-#define    RTL8367C_RTCT_EN_OFFSET    7
-#define    RTL8367C_RTCT_EN_MASK    0x80
-#define    RTL8367C_PON_LIGHT_EN_OFFSET    6
-#define    RTL8367C_PON_LIGHT_EN_MASK    0x40
-#define    RTL8367C_DW8051_EN_OFFSET    5
-#define    RTL8367C_DW8051_EN_MASK    0x20
-#define    RTL8367C_AUTOLOAD_EN_OFFSET    4
-#define    RTL8367C_AUTOLOAD_EN_MASK    0x10
-#define    RTL8367C_NRESTORE_EN_OFFSET    3
-#define    RTL8367C_NRESTORE_EN_MASK    0x8
-#define    RTL8367C_DIS_PON_TABLE_INIT_OFFSET    2
-#define    RTL8367C_DIS_PON_TABLE_INIT_MASK    0x4
-#define    RTL8367C_DIS_PON_BIST_OFFSET    1
-#define    RTL8367C_DIS_PON_BIST_MASK    0x2
-#define    RTL8367C_EFUSE_EN_OFFSET    0
-#define    RTL8367C_EFUSE_EN_MASK    0x1
-
-#define    RTL8367C_REG_MISCELLANEOUS_CONFIGURE1    0x130d
-#define    RTL8367C_EEPROM_DEV_ADR_OFFSET    8
-#define    RTL8367C_EEPROM_DEV_ADR_MASK    0x7F00
-#define    RTL8367C_EEPROM_MSB_OFFSET    7
-#define    RTL8367C_EEPROM_MSB_MASK    0x80
-#define    RTL8367C_EEPROM_ADDRESS_16B_OFFSET    6
-#define    RTL8367C_EEPROM_ADDRESS_16B_MASK    0x40
-#define    RTL8367C_EEPROM_DWONLOAD_COMPLETE_OFFSET    3
-#define    RTL8367C_EEPROM_DWONLOAD_COMPLETE_MASK    0x8
-#define    RTL8367C_SPI_SLAVE_EN_OFFSET    2
-#define    RTL8367C_SPI_SLAVE_EN_MASK    0x4
-#define    RTL8367C_SMI_SEL_OFFSET    0
-#define    RTL8367C_SMI_SEL_MASK    0x3
-
-#define    RTL8367C_REG_PHY_AD    0x130f
-#define    RTL8367C_EN_PHY_MAX_POWER_OFFSET    14
-#define    RTL8367C_EN_PHY_MAX_POWER_MASK    0x4000
-#define    RTL8367C_EN_PHY_SEL_DEG_OFFSET    13
-#define    RTL8367C_EN_PHY_SEL_DEG_MASK    0x2000
-#define    RTL8367C_EXTPHY_AD_OFFSET    8
-#define    RTL8367C_EXTPHY_AD_MASK    0x1F00
-#define    RTL8367C_EN_PHY_LOW_POWER_MODE_OFFSET    7
-#define    RTL8367C_EN_PHY_LOW_POWER_MODE_MASK    0x80
-#define    RTL8367C_EN_PHY_GREEN_OFFSET    6
-#define    RTL8367C_EN_PHY_GREEN_MASK    0x40
-#define    RTL8367C_PDNPHY_OFFSET    5
-#define    RTL8367C_PDNPHY_MASK    0x20
-#define    RTL8367C_INTPHY_AD_OFFSET    0
-#define    RTL8367C_INTPHY_AD_MASK    0x1F
-
-#define    RTL8367C_REG_DIGITAL_INTERFACE0_FORCE    0x1310
-#define    RTL8367C_GMII_0_FORCE_OFFSET    12
-#define    RTL8367C_GMII_0_FORCE_MASK    0x1000
-#define    RTL8367C_RGMII_0_FORCE_OFFSET    0
-#define    RTL8367C_RGMII_0_FORCE_MASK    0xFFF
-
-#define    RTL8367C_REG_DIGITAL_INTERFACE1_FORCE    0x1311
-#define    RTL8367C_GMII_1_FORCE_OFFSET    12
-#define    RTL8367C_GMII_1_FORCE_MASK    0x1000
-#define    RTL8367C_RGMII_1_FORCE_OFFSET    0
-#define    RTL8367C_RGMII_1_FORCE_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC0_FORCE_SELECT    0x1312
-#define    RTL8367C_EN_MAC0_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC0_FORCE_MASK    0x1000
-#define    RTL8367C_MAC0_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC0_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC1_FORCE_SELECT    0x1313
-#define    RTL8367C_EN_MAC1_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC1_FORCE_MASK    0x1000
-#define    RTL8367C_MAC1_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC1_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC2_FORCE_SELECT    0x1314
-#define    RTL8367C_EN_MAC2_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC2_FORCE_MASK    0x1000
-#define    RTL8367C_MAC2_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC2_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC3_FORCE_SELECT    0x1315
-#define    RTL8367C_EN_MAC3_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC3_FORCE_MASK    0x1000
-#define    RTL8367C_MAC3_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC3_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC4_FORCE_SELECT    0x1316
-#define    RTL8367C_EN_MAC4_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC4_FORCE_MASK    0x1000
-#define    RTL8367C_MAC4_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC4_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC5_FORCE_SELECT    0x1317
-#define    RTL8367C_EN_MAC5_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC5_FORCE_MASK    0x1000
-#define    RTL8367C_MAC5_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC5_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC6_FORCE_SELECT    0x1318
-#define    RTL8367C_EN_MAC6_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC6_FORCE_MASK    0x1000
-#define    RTL8367C_MAC6_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC6_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_MAC7_FORCE_SELECT    0x1319
-#define    RTL8367C_EN_MAC7_FORCE_OFFSET    12
-#define    RTL8367C_EN_MAC7_FORCE_MASK    0x1000
-#define    RTL8367C_MAC7_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_MAC7_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_M10_FORCE_SELECT    0x131c
-#define    RTL8367C_EN_M10_FORCE_OFFSET    12
-#define    RTL8367C_EN_M10_FORCE_MASK    0x1000
-#define    RTL8367C_M10_FORCE_ABLTY_OFFSET    0
-#define    RTL8367C_M10_FORCE_ABLTY_MASK    0xFFF
-
-#define    RTL8367C_REG_CHIP_RESET    0x1322
-#define    RTL8367C_GPHY_RESET_OFFSET    6
-#define    RTL8367C_GPHY_RESET_MASK    0x40
-#define    RTL8367C_NIC_RST_OFFSET    5
-#define    RTL8367C_NIC_RST_MASK    0x20
-#define    RTL8367C_DW8051_RST_OFFSET    4
-#define    RTL8367C_DW8051_RST_MASK    0x10
-#define    RTL8367C_SDS_RST_OFFSET    3
-#define    RTL8367C_SDS_RST_MASK    0x8
-#define    RTL8367C_CONFIG_RST_OFFSET    2
-#define    RTL8367C_CONFIG_RST_MASK    0x4
-#define    RTL8367C_SW_RST_OFFSET    1
-#define    RTL8367C_SW_RST_MASK    0x2
-#define    RTL8367C_CHIP_RST_OFFSET    0
-#define    RTL8367C_CHIP_RST_MASK    0x1
-
-#define    RTL8367C_REG_DIGITAL_DEBUG_0    0x1323
-
-#define    RTL8367C_REG_DIGITAL_DEBUG_1    0x1324
-
-#define    RTL8367C_REG_INTERNAL_PHY_MDC_DRIVER    0x1325
-#define    RTL8367C_INTERNAL_PHY_MDC_DRIVER_OFFSET    0
-#define    RTL8367C_INTERNAL_PHY_MDC_DRIVER_MASK    0x3FF
-
-#define    RTL8367C_REG_LINKDOWN_TIME_CTRL    0x1326
-#define    RTL8367C_LINKDOWN_TIME_CFG_OFFSET    9
-#define    RTL8367C_LINKDOWN_TIME_CFG_MASK    0x7E00
-#define    RTL8367C_LINKDOWN_TIME_ENABLE_OFFSET    8
-#define    RTL8367C_LINKDOWN_TIME_ENABLE_MASK    0x100
-#define    RTL8367C_LINKDOWN_TIME_OFFSET    0
-#define    RTL8367C_LINKDOWN_TIME_MASK    0xFF
-
-#define    RTL8367C_REG_PHYACK_TIMEOUT    0x1331
-
-#define    RTL8367C_REG_MDXACK_TIMEOUT    0x1333
-
-#define    RTL8367C_REG_DW8051_RDY    0x1336
-#define    RTL8367C_VIAROM_WRITE_EN_OFFSET    9
-#define    RTL8367C_VIAROM_WRITE_EN_MASK    0x200
-#define    RTL8367C_SPIF_CK2_OFFSET    8
-#define    RTL8367C_SPIF_CK2_MASK    0x100
-#define    RTL8367C_RRCP_MDOE_OFFSET    7
-#define    RTL8367C_RRCP_MDOE_MASK    0x80
-#define    RTL8367C_DW8051_RATE_OFFSET    4
-#define    RTL8367C_DW8051_RATE_MASK    0x70
-#define    RTL8367C_IROM_MSB_OFFSET    2
-#define    RTL8367C_IROM_MSB_MASK    0xC
-#define    RTL8367C_ACS_IROM_ENABLE_OFFSET    1
-#define    RTL8367C_ACS_IROM_ENABLE_MASK    0x2
-#define    RTL8367C_DW8051_READY_OFFSET    0
-#define    RTL8367C_DW8051_READY_MASK    0x1
-
-#define    RTL8367C_REG_BIST_CTRL    0x133c
-#define    RTL8367C_DRF_BIST_DONE_ALL_OFFSET    5
-#define    RTL8367C_DRF_BIST_DONE_ALL_MASK    0x20
-#define    RTL8367C_DRF_BIST_PAUSE_ALL_OFFSET    4
-#define    RTL8367C_DRF_BIST_PAUSE_ALL_MASK    0x10
-#define    RTL8367C_BIST_DOAN_ALL_OFFSET    3
-#define    RTL8367C_BIST_DOAN_ALL_MASK    0x8
-#define    RTL8367C_BIST_PASS_OFFSET    0
-#define    RTL8367C_BIST_PASS_MASK    0x7
-
-#define    RTL8367C_REG_DIAG_MODE2    0x133d
-#define    RTL8367C_DIAG_MODE2_ACTRAM_OFFSET    1
-#define    RTL8367C_DIAG_MODE2_ACTRAM_MASK    0x2
-#define    RTL8367C_DIAG_MODE2_BCAM_ACTION_OFFSET    0
-#define    RTL8367C_DIAG_MODE2_BCAM_ACTION_MASK    0x1
-
-#define    RTL8367C_REG_MDX_PHY_REG0    0x133e
-#define    RTL8367C_PHY_BRD_MASK_OFFSET    4
-#define    RTL8367C_PHY_BRD_MASK_MASK    0x1F0
-#define    RTL8367C_MDX_INDACC_PAGE_OFFSET    0
-#define    RTL8367C_MDX_INDACC_PAGE_MASK    0xF
-
-#define    RTL8367C_REG_MDX_PHY_REG1    0x133f
-#define    RTL8367C_PHY_BRD_MODE_OFFSET    5
-#define    RTL8367C_PHY_BRD_MODE_MASK    0x20
-#define    RTL8367C_BRD_PHYAD_OFFSET    0
-#define    RTL8367C_BRD_PHYAD_MASK    0x1F
-
-#define    RTL8367C_REG_DEBUG_SIGNAL_SELECT_SW    0x1340
-
-#define    RTL8367C_REG_DEBUG_SIGNAL_SELECT_B    0x1341
-#define    RTL8367C_DEBUG_MX_OFFSET    9
-#define    RTL8367C_DEBUG_MX_MASK    0xE00
-#define    RTL8367C_DEBUG_SHIFT_MISC_OFFSET    6
-#define    RTL8367C_DEBUG_SHIFT_MISC_MASK    0x1C0
-#define    RTL8367C_DEBUG_SHIFT_SW_OFFSET    3
-#define    RTL8367C_DEBUG_SHIFT_SW_MASK    0x38
-#define    RTL8367C_DEBUG_SHIFT_GPHY_OFFSET    0
-#define    RTL8367C_DEBUG_SHIFT_GPHY_MASK    0x7
-
-#define    RTL8367C_REG_DEBUG_SIGNAL_I    0x1343
-
-#define    RTL8367C_REG_DEBUG_SIGNAL_H    0x1344
-
-#define    RTL8367C_REG_DBGO_SEL_GPHY    0x1345
-
-#define    RTL8367C_REG_DBGO_SEL_MISC    0x1346
-
-#define    RTL8367C_REG_BYPASS_ABLTY_LOCK    0x1349
-#define    RTL8367C_BYPASS_ABLTY_LOCK_OFFSET    0
-#define    RTL8367C_BYPASS_ABLTY_LOCK_MASK    0xFF
-
-#define    RTL8367C_REG_BYPASS_ABLTY_LOCK_EXT    0x134a
-#define    RTL8367C_BYPASS_P10_ABILIITY_LOCK_OFFSET    3
-#define    RTL8367C_BYPASS_P10_ABILIITY_LOCK_MASK    0x8
-#define    RTL8367C_BYPASS_EXT_ABILITY_LOCK_OFFSET    0
-#define    RTL8367C_BYPASS_EXT_ABILITY_LOCK_MASK    0x7
-
-#define    RTL8367C_REG_ACL_GPIO    0x134f
-#define    RTL8367C_ACL_GPIO_13_OFFSET    13
-#define    RTL8367C_ACL_GPIO_13_MASK    0x2000
-#define    RTL8367C_ACL_GPIO_12_OFFSET    12
-#define    RTL8367C_ACL_GPIO_12_MASK    0x1000
-#define    RTL8367C_ACL_GPIO_11_OFFSET    11
-#define    RTL8367C_ACL_GPIO_11_MASK    0x800
-#define    RTL8367C_ACL_GPIO_10_OFFSET    10
-#define    RTL8367C_ACL_GPIO_10_MASK    0x400
-#define    RTL8367C_ACL_GPIO_9_OFFSET    9
-#define    RTL8367C_ACL_GPIO_9_MASK    0x200
-#define    RTL8367C_ACL_GPIO_8_OFFSET    8
-#define    RTL8367C_ACL_GPIO_8_MASK    0x100
-#define    RTL8367C_ACL_GPIO_7_OFFSET    7
-#define    RTL8367C_ACL_GPIO_7_MASK    0x80
-#define    RTL8367C_ACL_GPIO_6_OFFSET    6
-#define    RTL8367C_ACL_GPIO_6_MASK    0x40
-#define    RTL8367C_ACL_GPIO_5_OFFSET    5
-#define    RTL8367C_ACL_GPIO_5_MASK    0x20
-#define    RTL8367C_ACL_GPIO_4_OFFSET    4
-#define    RTL8367C_ACL_GPIO_4_MASK    0x10
-#define    RTL8367C_ACL_GPIO_3_OFFSET    3
-#define    RTL8367C_ACL_GPIO_3_MASK    0x8
-#define    RTL8367C_ACL_GPIO_2_OFFSET    2
-#define    RTL8367C_ACL_GPIO_2_MASK    0x4
-#define    RTL8367C_ACL_GPIO_1_OFFSET    1
-#define    RTL8367C_ACL_GPIO_1_MASK    0x2
-#define    RTL8367C_ACL_GPIO_0_OFFSET    0
-#define    RTL8367C_ACL_GPIO_0_MASK    0x1
-
-#define    RTL8367C_REG_EN_GPIO    0x1350
-#define    RTL8367C_EN_GPIO_13_OFFSET    13
-#define    RTL8367C_EN_GPIO_13_MASK    0x2000
-#define    RTL8367C_EN_GPIO_12_OFFSET    12
-#define    RTL8367C_EN_GPIO_12_MASK    0x1000
-#define    RTL8367C_EN_GPIO_11_OFFSET    11
-#define    RTL8367C_EN_GPIO_11_MASK    0x800
-#define    RTL8367C_EN_GPIO_10_OFFSET    10
-#define    RTL8367C_EN_GPIO_10_MASK    0x400
-#define    RTL8367C_EN_GPIO_9_OFFSET    9
-#define    RTL8367C_EN_GPIO_9_MASK    0x200
-#define    RTL8367C_EN_GPIO_8_OFFSET    8
-#define    RTL8367C_EN_GPIO_8_MASK    0x100
-#define    RTL8367C_EN_GPIO_7_OFFSET    7
-#define    RTL8367C_EN_GPIO_7_MASK    0x80
-#define    RTL8367C_EN_GPIO_6_OFFSET    6
-#define    RTL8367C_EN_GPIO_6_MASK    0x40
-#define    RTL8367C_EN_GPIO_5_OFFSET    5
-#define    RTL8367C_EN_GPIO_5_MASK    0x20
-#define    RTL8367C_EN_GPIO_4_OFFSET    4
-#define    RTL8367C_EN_GPIO_4_MASK    0x10
-#define    RTL8367C_EN_GPIO_3_OFFSET    3
-#define    RTL8367C_EN_GPIO_3_MASK    0x8
-#define    RTL8367C_EN_GPIO_2_OFFSET    2
-#define    RTL8367C_EN_GPIO_2_MASK    0x4
-#define    RTL8367C_EN_GPIO_1_OFFSET    1
-#define    RTL8367C_EN_GPIO_1_MASK    0x2
-#define    RTL8367C_EN_GPIO_0_OFFSET    0
-#define    RTL8367C_EN_GPIO_0_MASK    0x1
-
-#define    RTL8367C_REG_CFG_MULTI_PIN    0x1351
-#define    RTL8367C_CFG_MULTI_PIN_OFFSET    0
-#define    RTL8367C_CFG_MULTI_PIN_MASK    0x3
-
-#define    RTL8367C_REG_PORT0_STATUS    0x1352
-#define    RTL8367C_PORT0_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT0_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT0_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT0_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT0_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT0_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT0_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT0_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT0_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT0_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT0_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT0_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT0_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT0_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT0_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT0_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT0_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT0_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT0_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT0_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT1_STATUS    0x1353
-#define    RTL8367C_PORT1_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT1_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT1_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT1_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT1_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT1_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT1_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT1_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT1_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT1_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT1_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT1_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT1_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT1_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT1_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT1_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT1_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT1_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT1_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT1_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT2_STATUS    0x1354
-#define    RTL8367C_PORT2_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT2_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT2_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT2_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT2_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT2_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT2_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT2_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT2_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT2_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT2_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT2_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT2_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT2_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT2_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT2_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT2_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT2_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT2_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT2_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT3_STATUS    0x1355
-#define    RTL8367C_PORT3_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT3_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT3_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT3_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT3_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT3_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT3_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT3_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT3_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT3_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT3_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT3_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT3_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT3_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT3_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT3_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT3_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT3_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT3_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT3_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT4_STATUS    0x1356
-#define    RTL8367C_PORT4_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT4_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT4_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT4_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT4_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT4_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT4_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT4_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT4_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT4_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT4_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT4_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT4_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT4_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT4_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT4_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT4_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT4_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT4_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT4_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT5_STATUS    0x1357
-#define    RTL8367C_PORT5_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT5_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT5_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT5_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT5_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT5_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT5_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT5_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT5_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT5_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT5_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT5_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT5_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT5_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT5_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT5_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT5_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT5_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT5_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT5_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT6_STATUS    0x1358
-#define    RTL8367C_PORT6_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT6_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT6_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT6_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT6_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT6_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT6_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT6_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT6_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT6_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT6_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT6_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT6_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT6_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT6_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT6_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT6_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT6_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT6_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT6_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT7_STATUS    0x1359
-#define    RTL8367C_PORT7_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT7_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT7_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT7_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT7_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT7_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT7_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT7_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT7_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT7_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT7_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT7_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT7_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT7_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT7_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT7_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT7_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT7_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT7_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT7_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT8_STATUS    0x135a
-#define    RTL8367C_PORT8_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT8_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT8_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT8_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT8_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT8_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT8_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT8_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT8_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT8_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT8_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT8_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT8_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT8_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT8_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT8_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT8_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT8_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT8_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT8_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT9_STATUS    0x135b
-#define    RTL8367C_PORT9_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT9_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT9_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT9_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT9_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT9_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT9_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT9_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT9_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT9_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT9_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT9_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT9_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT9_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT9_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT9_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT9_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT9_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT9_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT9_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_PORT10_STATUS    0x135c
-#define    RTL8367C_PORT10_STATUS_EN_1000_LPI_OFFSET    11
-#define    RTL8367C_PORT10_STATUS_EN_1000_LPI_MASK    0x800
-#define    RTL8367C_PORT10_STATUS_EN_100_LPI_OFFSET    10
-#define    RTL8367C_PORT10_STATUS_EN_100_LPI_MASK    0x400
-#define    RTL8367C_PORT10_STATUS_NWAY_FAULT_OFFSET    9
-#define    RTL8367C_PORT10_STATUS_NWAY_FAULT_MASK    0x200
-#define    RTL8367C_PORT10_STATUS_LINK_ON_MASTER_OFFSET    8
-#define    RTL8367C_PORT10_STATUS_LINK_ON_MASTER_MASK    0x100
-#define    RTL8367C_PORT10_STATUS_NWAY_CAP_OFFSET    7
-#define    RTL8367C_PORT10_STATUS_NWAY_CAP_MASK    0x80
-#define    RTL8367C_PORT10_STATUS_TX_FLOWCTRL_CAP_OFFSET    6
-#define    RTL8367C_PORT10_STATUS_TX_FLOWCTRL_CAP_MASK    0x40
-#define    RTL8367C_PORT10_STATUS_RX_FLOWCTRL_CAP_OFFSET    5
-#define    RTL8367C_PORT10_STATUS_RX_FLOWCTRL_CAP_MASK    0x20
-#define    RTL8367C_PORT10_STATUS_LINK_STATE_OFFSET    4
-#define    RTL8367C_PORT10_STATUS_LINK_STATE_MASK    0x10
-#define    RTL8367C_PORT10_STATUS_FULL_DUPLUX_CAP_OFFSET    2
-#define    RTL8367C_PORT10_STATUS_FULL_DUPLUX_CAP_MASK    0x4
-#define    RTL8367C_PORT10_STATUS_LINK_SPEED_OFFSET    0
-#define    RTL8367C_PORT10_STATUS_LINK_SPEED_MASK    0x3
-
-#define    RTL8367C_REG_UPS_CTRL0    0x1362
-#define    RTL8367C_P3_REF_SD_BIT0_OFFSET    8
-#define    RTL8367C_P3_REF_SD_BIT0_MASK    0xFF00
-#define    RTL8367C_P2_REF_SD_OFFSET    0
-#define    RTL8367C_P2_REF_SD_MASK    0xFF
-
-#define    RTL8367C_REG_UPS_CTRL1    0x1363
-#define    RTL8367C_UPS_OUT_OFFSET    8
-#define    RTL8367C_UPS_OUT_MASK    0xFF00
-#define    RTL8367C_UPS_WRITE_PULSE_OFFSET    1
-#define    RTL8367C_UPS_WRITE_PULSE_MASK    0x2
-#define    RTL8367C_UPS_EN_OFFSET    0
-#define    RTL8367C_UPS_EN_MASK    0x1
-
-#define    RTL8367C_REG_UPS_CTRL2    0x1364
-#define    RTL8367C_IGNOE_MAC8_LINK_OFFSET    15
-#define    RTL8367C_IGNOE_MAC8_LINK_MASK    0x8000
-#define    RTL8367C_AGREE_SLEEP_OFFSET    14
-#define    RTL8367C_AGREE_SLEEP_MASK    0x4000
-#define    RTL8367C_WAIT_FOR_AGREEMENT_OFFSET    13
-#define    RTL8367C_WAIT_FOR_AGREEMENT_MASK    0x2000
-#define    RTL8367C_WAKE_UP_BY_LINK_OFFSET    12
-#define    RTL8367C_WAKE_UP_BY_LINK_MASK    0x1000
-#define    RTL8367C_WAKE_UP_BY_PHY_OFFSET    11
-#define    RTL8367C_WAKE_UP_BY_PHY_MASK    0x800
-#define    RTL8367C_SLOW_CLK_TGL_RATE_OFFSET    7
-#define    RTL8367C_SLOW_CLK_TGL_RATE_MASK    0x780
-#define    RTL8367C_PLL_G1_CTRL_EN_OFFSET    6
-#define    RTL8367C_PLL_G1_CTRL_EN_MASK    0x40
-#define    RTL8367C_PLL_G0_CTRL_EN_OFFSET    5
-#define    RTL8367C_PLL_G0_CTRL_EN_MASK    0x20
-#define    RTL8367C_SLOW_DOWN_PLL_EN_OFFSET    4
-#define    RTL8367C_SLOW_DOWN_PLL_EN_MASK    0x10
-#define    RTL8367C_SLOW_DOWN_CLK_EN_OFFSET    3
-#define    RTL8367C_SLOW_DOWN_CLK_EN_MASK    0x8
-#define    RTL8367C_GATING_CLK_SDS_EN_OFFSET    2
-#define    RTL8367C_GATING_CLK_SDS_EN_MASK    0x4
-#define    RTL8367C_GATING_CLK_CHIP_EN_OFFSET    1
-#define    RTL8367C_GATING_CLK_CHIP_EN_MASK    0x2
-#define    RTL8367C_GATING_SW_EN_OFFSET    0
-#define    RTL8367C_GATING_SW_EN_MASK    0x1
-
-#define    RTL8367C_REG_GATING_CLK_1    0x1365
-#define    RTL8367C_ALDPS_MODE_4_OFFSET    15
-#define    RTL8367C_ALDPS_MODE_4_MASK    0x8000
-#define    RTL8367C_ALDPS_MODE_3_OFFSET    14
-#define    RTL8367C_ALDPS_MODE_3_MASK    0x4000
-#define    RTL8367C_ALDPS_MODE_2_OFFSET    13
-#define    RTL8367C_ALDPS_MODE_2_MASK    0x2000
-#define    RTL8367C_ALDPS_MODE_1_OFFSET    12
-#define    RTL8367C_ALDPS_MODE_1_MASK    0x1000
-#define    RTL8367C_ALDPS_MODE_0_OFFSET    11
-#define    RTL8367C_ALDPS_MODE_0_MASK    0x800
-#define    RTL8367C_UPS_DBGO_OFFSET    10
-#define    RTL8367C_UPS_DBGO_MASK    0x400
-#define    RTL8367C_IFMX_AFF_NOT_FF_OUT_OFFSET    9
-#define    RTL8367C_IFMX_AFF_NOT_FF_OUT_MASK    0x200
-#define    RTL8367C_WATER_LEVEL_FD_OFFSET    6
-#define    RTL8367C_WATER_LEVEL_FD_MASK    0x1C0
-#define    RTL8367C_WATER_LEVEL_Y2X_OFFSET    3
-#define    RTL8367C_WATER_LEVEL_Y2X_MASK    0x38
-#define    RTL8367C_WATER_LEVEL_X2Y_2_OFFSET    2
-#define    RTL8367C_WATER_LEVEL_X2Y_2_MASK    0x4
-#define    RTL8367C_IGNOE_MAC10_LINK_OFFSET    1
-#define    RTL8367C_IGNOE_MAC10_LINK_MASK    0x2
-#define    RTL8367C_IGNOE_MAC9_LINK_OFFSET    0
-#define    RTL8367C_IGNOE_MAC9_LINK_MASK    0x1
-
-#define    RTL8367C_REG_UPS_CTRL4    0x1366
-#define    RTL8367C_PROB_EN_OFFSET    6
-#define    RTL8367C_PROB_EN_MASK    0x40
-#define    RTL8367C_PLL_DOWN_OFFSET    1
-#define    RTL8367C_PLL_DOWN_MASK    0x2
-#define    RTL8367C_XTAL_DOWN_OFFSET    0
-#define    RTL8367C_XTAL_DOWN_MASK    0x1
-
-#define    RTL8367C_REG_UPS_CTRL5    0x1367
-#define    RTL8367C_FRC_CPU_ACPT_OFFSET    3
-#define    RTL8367C_FRC_CPU_ACPT_MASK    0x8
-#define    RTL8367C_UPS_CPU_ACPT_OFFSET    2
-#define    RTL8367C_UPS_CPU_ACPT_MASK    0x4
-#define    RTL8367C_UPS_DBG_4_OFFSET    0
-#define    RTL8367C_UPS_DBG_4_MASK    0x3
-
-#define    RTL8367C_REG_UPS_CTRL6    0x1368
-#define    RTL8367C_UPS_CTRL6_OFFSET    0
-#define    RTL8367C_UPS_CTRL6_MASK    0xF
-
-#define    RTL8367C_REG_EFUSE_CMD_70B    0x1369
-
-#define    RTL8367C_REG_EFUSE_CMD    0x1370
-#define    RTL8367C_EFUSE_TIME_OUT_FLAG_OFFSET    3
-#define    RTL8367C_EFUSE_TIME_OUT_FLAG_MASK    0x8
-#define    RTL8367C_EFUSE_ACCESS_BUSY_OFFSET    2
-#define    RTL8367C_EFUSE_ACCESS_BUSY_MASK    0x4
-#define    RTL8367C_EFUSE_COMMAND_EN_OFFSET    1
-#define    RTL8367C_EFUSE_COMMAND_EN_MASK    0x2
-#define    RTL8367C_EFUSE_WR_OFFSET    0
-#define    RTL8367C_EFUSE_WR_MASK    0x1
-
-#define    RTL8367C_REG_EFUSE_ADR    0x1371
-#define    RTL8367C_DUMMY_15_10_OFFSET    8
-#define    RTL8367C_DUMMY_15_10_MASK    0xFF00
-#define    RTL8367C_EFUSE_ADDRESS_OFFSET    0
-#define    RTL8367C_EFUSE_ADDRESS_MASK    0xFF
-
-#define    RTL8367C_REG_EFUSE_WDAT    0x1372
-
-#define    RTL8367C_REG_EFUSE_RDAT    0x1373
-
-#define    RTL8367C_REG_I2C_CTRL    0x1374
-#define    RTL8367C_MDX_MST_FAIL_LAT_OFFSET    1
-#define    RTL8367C_MDX_MST_FAIL_LAT_MASK    0x2
-#define    RTL8367C_MDX_MST_FAIL_CLRPS_OFFSET    0
-#define    RTL8367C_MDX_MST_FAIL_CLRPS_MASK    0x1
-
-#define    RTL8367C_REG_EEE_CFG    0x1375
-#define    RTL8367C_CFG_BYPASS_GATELPTD_OFFSET    11
-#define    RTL8367C_CFG_BYPASS_GATELPTD_MASK    0x800
-#define    RTL8367C_EEE_ABT_ADDR2_OFFSET    6
-#define    RTL8367C_EEE_ABT_ADDR2_MASK    0x7C0
-#define    RTL8367C_EEE_ABT_ADDR1_OFFSET    1
-#define    RTL8367C_EEE_ABT_ADDR1_MASK    0x3E
-#define    RTL8367C_EEE_POLL_EN_OFFSET    0
-#define    RTL8367C_EEE_POLL_EN_MASK    0x1
-
-#define    RTL8367C_REG_EEE_PAGE    0x1376
-
-#define    RTL8367C_REG_EEE_EXT_PAGE    0x1377
-
-#define    RTL8367C_REG_EEE_EN_SPD1000    0x1378
-
-#define    RTL8367C_REG_EEE_EN_SPD100    0x1379
-
-#define    RTL8367C_REG_EEE_LP_SPD1000    0x137a
-
-#define    RTL8367C_REG_EEE_LP_SPD100    0x137b
-
-#define    RTL8367C_REG_DW8051_PRO_REG0    0x13a0
-
-#define    RTL8367C_REG_DW8051_PRO_REG1    0x13a1
-
-#define    RTL8367C_REG_DW8051_PRO_REG2    0x13a2
-
-#define    RTL8367C_REG_DW8051_PRO_REG3    0x13a3
-
-#define    RTL8367C_REG_DW8051_PRO_REG4    0x13a4
-
-#define    RTL8367C_REG_DW8051_PRO_REG5    0x13a5
-
-#define    RTL8367C_REG_DW8051_PRO_REG6    0x13a6
-
-#define    RTL8367C_REG_DW8051_PRO_REG7    0x13a7
-
-#define    RTL8367C_REG_PROTECT_ID    0x13c0
-
-#define    RTL8367C_REG_CHIP_VER_INTL    0x13c1
-#define    RTL8367C_CHIP_VER_INTL_OFFSET    0
-#define    RTL8367C_CHIP_VER_INTL_MASK    0xF
-
-#define    RTL8367C_REG_MAGIC_ID    0x13c2
-
-#define    RTL8367C_REG_DIGITAL_INTERFACE_SELECT_1    0x13c3
-#define    RTL8367C_SKIP_MII_2_RXER_OFFSET    4
-#define    RTL8367C_SKIP_MII_2_RXER_MASK    0x10
-#define    RTL8367C_SELECT_GMII_2_OFFSET    0
-#define    RTL8367C_SELECT_GMII_2_MASK    0xF
-
-#define    RTL8367C_REG_DIGITAL_INTERFACE2_FORCE    0x13c4
-#define    RTL8367C_GMII_2_FORCE_OFFSET    12
-#define    RTL8367C_GMII_2_FORCE_MASK    0x1000
-#define    RTL8367C_RGMII_2_FORCE_OFFSET    0
-#define    RTL8367C_RGMII_2_FORCE_MASK    0xFFF
-
-#define    RTL8367C_REG_EXT2_RGMXF    0x13c5
-#define    RTL8367C_EXT2_RGTX_INV_OFFSET    6
-#define    RTL8367C_EXT2_RGTX_INV_MASK    0x40
-#define    RTL8367C_EXT2_RGRX_INV_OFFSET    5
-#define    RTL8367C_EXT2_RGRX_INV_MASK    0x20
-#define    RTL8367C_EXT2_RGMXF_OFFSET    0
-#define    RTL8367C_EXT2_RGMXF_MASK    0x1F
-
-#define    RTL8367C_REG_ROUTER_UPS_CFG    0x13c6
-#define    RTL8367C_UPS_Status_OFFSET    1
-#define    RTL8367C_UPS_Status_MASK    0x2
-#define    RTL8367C_SoftStart_OFFSET    0
-#define    RTL8367C_SoftStart_MASK    0x1
-
-#define    RTL8367C_REG_CTRL_GPIO    0x13c7
-#define    RTL8367C_CTRL_GPIO_13_OFFSET    13
-#define    RTL8367C_CTRL_GPIO_13_MASK    0x2000
-#define    RTL8367C_CTRL_GPIO_12_OFFSET    12
-#define    RTL8367C_CTRL_GPIO_12_MASK    0x1000
-#define    RTL8367C_CTRL_GPIO_11_OFFSET    11
-#define    RTL8367C_CTRL_GPIO_11_MASK    0x800
-#define    RTL8367C_CTRL_GPIO_10_OFFSET    10
-#define    RTL8367C_CTRL_GPIO_10_MASK    0x400
-#define    RTL8367C_CTRL_GPIO_9_OFFSET    9
-#define    RTL8367C_CTRL_GPIO_9_MASK    0x200
-#define    RTL8367C_CTRL_GPIO_8_OFFSET    8
-#define    RTL8367C_CTRL_GPIO_8_MASK    0x100
-#define    RTL8367C_CTRL_GPIO_7_OFFSET    7
-#define    RTL8367C_CTRL_GPIO_7_MASK    0x80
-#define    RTL8367C_CTRL_GPIO_6_OFFSET    6
-#define    RTL8367C_CTRL_GPIO_6_MASK    0x40
-#define    RTL8367C_CTRL_GPIO_5_OFFSET    5
-#define    RTL8367C_CTRL_GPIO_5_MASK    0x20
-#define    RTL8367C_CTRL_GPIO_4_OFFSET    4
-#define    RTL8367C_CTRL_GPIO_4_MASK    0x10
-#define    RTL8367C_CTRL_GPIO_3_OFFSET    3
-#define    RTL8367C_CTRL_GPIO_3_MASK    0x8
-#define    RTL8367C_CTRL_GPIO_2_OFFSET    2
-#define    RTL8367C_CTRL_GPIO_2_MASK    0x4
-#define    RTL8367C_CTRL_GPIO_1_OFFSET    1
-#define    RTL8367C_CTRL_GPIO_1_MASK    0x2
-#define    RTL8367C_CTRL_GPIO_0_OFFSET    0
-#define    RTL8367C_CTRL_GPIO_0_MASK    0x1
-
-#define    RTL8367C_REG_SEL_GPIO    0x13c8
-#define    RTL8367C_SEL_GPIO_13_OFFSET    13
-#define    RTL8367C_SEL_GPIO_13_MASK    0x2000
-#define    RTL8367C_SEL_GPIO_12_OFFSET    12
-#define    RTL8367C_SEL_GPIO_12_MASK    0x1000
-#define    RTL8367C_SEL_GPIO_11_OFFSET    11
-#define    RTL8367C_SEL_GPIO_11_MASK    0x800
-#define    RTL8367C_SEL_GPIO_10_OFFSET    10
-#define    RTL8367C_SEL_GPIO_10_MASK    0x400
-#define    RTL8367C_SEL_GPIO_9_OFFSET    9
-#define    RTL8367C_SEL_GPIO_9_MASK    0x200
-#define    RTL8367C_SEL_GPIO_8_OFFSET    8
-#define    RTL8367C_SEL_GPIO_8_MASK    0x100
-#define    RTL8367C_SEL_GPIO_7_OFFSET    7
-#define    RTL8367C_SEL_GPIO_7_MASK    0x80
-#define    RTL8367C_SEL_GPIO_6_OFFSET    6
-#define    RTL8367C_SEL_GPIO_6_MASK    0x40
-#define    RTL8367C_SEL_GPIO_5_OFFSET    5
-#define    RTL8367C_SEL_GPIO_5_MASK    0x20
-#define    RTL8367C_SEL_GPIO_4_OFFSET    4
-#define    RTL8367C_SEL_GPIO_4_MASK    0x10
-#define    RTL8367C_SEL_GPIO_3_OFFSET    3
-#define    RTL8367C_SEL_GPIO_3_MASK    0x8
-#define    RTL8367C_SEL_GPIO_2_OFFSET    2
-#define    RTL8367C_SEL_GPIO_2_MASK    0x4
-#define    RTL8367C_SEL_GPIO_1_OFFSET    1
-#define    RTL8367C_SEL_GPIO_1_MASK    0x2
-#define    RTL8367C_SEL_GPIO_0_OFFSET    0
-#define    RTL8367C_SEL_GPIO_0_MASK    0x1
-
-#define    RTL8367C_REG_STATUS_GPIO    0x13c9
-#define    RTL8367C_STATUS_GPIO_OFFSET    0
-#define    RTL8367C_STATUS_GPIO_MASK    0x3FFF
-
-#define    RTL8367C_REG_SYNC_ETH_CFG    0x13e0
-#define    RTL8367C_DUMMY2_OFFSET    9
-#define    RTL8367C_DUMMY2_MASK    0xFE00
-#define    RTL8367C_RFC2819_TYPE_OFFSET    8
-#define    RTL8367C_RFC2819_TYPE_MASK    0x100
-#define    RTL8367C_DUMMY1_OFFSET    7
-#define    RTL8367C_DUMMY1_MASK    0x80
-#define    RTL8367C_FIBER_SYNCE125_L_SEL_OFFSET    6
-#define    RTL8367C_FIBER_SYNCE125_L_SEL_MASK    0x40
-#define    RTL8367C_SYNC_ETH_EN_RTT2_OFFSET    5
-#define    RTL8367C_SYNC_ETH_EN_RTT2_MASK    0x20
-#define    RTL8367C_SYNC_ETH_EN_RTT1_OFFSET    4
-#define    RTL8367C_SYNC_ETH_EN_RTT1_MASK    0x10
-#define    RTL8367C_SYNC_ETH_SEL_DPLL_OFFSET    3
-#define    RTL8367C_SYNC_ETH_SEL_DPLL_MASK    0x8
-#define    RTL8367C_SYNC_ETH_SEL_PHYREF_OFFSET    2
-#define    RTL8367C_SYNC_ETH_SEL_PHYREF_MASK    0x4
-#define    RTL8367C_SYNC_ETH_SEL_XTAL_OFFSET    1
-#define    RTL8367C_SYNC_ETH_SEL_XTAL_MASK    0x2
-#define    RTL8367C_DUMMY0_OFFSET    0
-#define    RTL8367C_DUMMY0_MASK    0x1
-
-#define    RTL8367C_REG_LED_DRI_CFG    0x13e1
-#define    RTL8367C_LED_DRI_CFG_DUMMY_OFFSET    1
-#define    RTL8367C_LED_DRI_CFG_DUMMY_MASK    0xFFFE
-#define    RTL8367C_LED_DRIVING_OFFSET    0
-#define    RTL8367C_LED_DRIVING_MASK    0x1
-
-#define    RTL8367C_REG_CHIP_DEBUG2    0x13e2
-#define    RTL8367C_RG2_DN_OFFSET    6
-#define    RTL8367C_RG2_DN_MASK    0x1C0
-#define    RTL8367C_RG2_DP_OFFSET    3
-#define    RTL8367C_RG2_DP_MASK    0x38
-#define    RTL8367C_DRI_EXT2_RG_OFFSET    2
-#define    RTL8367C_DRI_EXT2_RG_MASK    0x4
-#define    RTL8367C_DRI_EXT2_OFFSET    1
-#define    RTL8367C_DRI_EXT2_MASK    0x2
-#define    RTL8367C_SLR_EXT2_OFFSET    0
-#define    RTL8367C_SLR_EXT2_MASK    0x1
-
-#define    RTL8367C_REG_DIGITAL_DEBUG_2    0x13e3
-
-#define    RTL8367C_REG_FIBER_RTL_OUI_CFG0    0x13e4
-#define    RTL8367C_FIBER_RTL_OUI_CFG0_OFFSET    0
-#define    RTL8367C_FIBER_RTL_OUI_CFG0_MASK    0xFF
-
-#define    RTL8367C_REG_FIBER_RTL_OUI_CFG1    0x13e5
-
-#define    RTL8367C_REG_FIBER_CFG_0    0x13e6
-#define    RTL8367C_REV_NUM_OFFSET    8
-#define    RTL8367C_REV_NUM_MASK    0xF00
-#define    RTL8367C_MODEL_NUM_OFFSET    0
-#define    RTL8367C_MODEL_NUM_MASK    0x3F
-
-#define    RTL8367C_REG_FIBER_CFG_1    0x13e7
-#define    RTL8367C_SDS_FRC_REG4_OFFSET    12
-#define    RTL8367C_SDS_FRC_REG4_MASK    0x1000
-#define    RTL8367C_SDS_FRC_REG4_FIB100_OFFSET    11
-#define    RTL8367C_SDS_FRC_REG4_FIB100_MASK    0x800
-#define    RTL8367C_SEL_MASK_ONL_OFFSET    5
-#define    RTL8367C_SEL_MASK_ONL_MASK    0x20
-#define    RTL8367C_DIS_QUALITY_IN_MASK_OFFSET    4
-#define    RTL8367C_DIS_QUALITY_IN_MASK_MASK    0x10
-#define    RTL8367C_SDS_FRC_MODE_OFFSET    3
-#define    RTL8367C_SDS_FRC_MODE_MASK    0x8
-#define    RTL8367C_SDS_MODE_OFFSET    0
-#define    RTL8367C_SDS_MODE_MASK    0x7
-
-#define    RTL8367C_REG_FIBER_CFG_2    0x13e8
-#define    RTL8367C_SEL_SDET_PS_OFFSET    12
-#define    RTL8367C_SEL_SDET_PS_MASK    0xF000
-#define    RTL8367C_UTP_DIS_RX_OFFSET    10
-#define    RTL8367C_UTP_DIS_RX_MASK    0xC00
-#define    RTL8367C_UTP_FRC_LD_OFFSET    8
-#define    RTL8367C_UTP_FRC_LD_MASK    0x300
-#define    RTL8367C_SDS_RX_DISABLE_OFFSET    6
-#define    RTL8367C_SDS_RX_DISABLE_MASK    0xC0
-#define    RTL8367C_SDS_TX_DISABLE_OFFSET    4
-#define    RTL8367C_SDS_TX_DISABLE_MASK    0x30
-#define    RTL8367C_FIBER_CFG_2_SDS_PWR_ISO_OFFSET    2
-#define    RTL8367C_FIBER_CFG_2_SDS_PWR_ISO_MASK    0xC
-#define    RTL8367C_SDS_FRC_LD_OFFSET    0
-#define    RTL8367C_SDS_FRC_LD_MASK    0x3
-
-#define    RTL8367C_REG_FIBER_CFG_3    0x13e9
-#define    RTL8367C_FIBER_CFG_3_OFFSET    0
-#define    RTL8367C_FIBER_CFG_3_MASK    0xFFF
-
-#define    RTL8367C_REG_FIBER_CFG_4    0x13ea
-
-#define    RTL8367C_REG_UTP_FIB_DET    0x13eb
-#define    RTL8367C_FORCE_SEL_FIBER_OFFSET    14
-#define    RTL8367C_FORCE_SEL_FIBER_MASK    0xC000
-#define    RTL8367C_FIB_FINAL_TIMER_OFFSET    12
-#define    RTL8367C_FIB_FINAL_TIMER_MASK    0x3000
-#define    RTL8367C_FIB_LINK_TIMER_OFFSET    10
-#define    RTL8367C_FIB_LINK_TIMER_MASK    0xC00
-#define    RTL8367C_FIB_SDET_TIMER_OFFSET    8
-#define    RTL8367C_FIB_SDET_TIMER_MASK    0x300
-#define    RTL8367C_UTP_LINK_TIMER_OFFSET    6
-#define    RTL8367C_UTP_LINK_TIMER_MASK    0xC0
-#define    RTL8367C_UTP_SDET_TIMER_OFFSET    4
-#define    RTL8367C_UTP_SDET_TIMER_MASK    0x30
-#define    RTL8367C_FORCE_AUTODET_OFFSET    3
-#define    RTL8367C_FORCE_AUTODET_MASK    0x8
-#define    RTL8367C_AUTODET_FSM_CLR_OFFSET    2
-#define    RTL8367C_AUTODET_FSM_CLR_MASK    0x4
-#define    RTL8367C_UTP_FIRST_OFFSET    1
-#define    RTL8367C_UTP_FIRST_MASK    0x2
-#define    RTL8367C_UTP_FIB_DISAUTODET_OFFSET    0
-#define    RTL8367C_UTP_FIB_DISAUTODET_MASK    0x1
-
-#define    RTL8367C_REG_NRESTORE_MAGIC_NUM    0x13ec
-#define    RTL8367C_NRESTORE_MAGIC_NUM_MASK    0xFFFF
-#define    RTL8367C_EEPROM_PROGRAM_CYCLE_OFFSET    0
-#define    RTL8367C_EEPROM_PROGRAM_CYCLE_MASK    0x3
-
-#define    RTL8367C_REG_MAC_ACTIVE    0x13ee
-#define    RTL8367C_MAC_ACTIVE_H_OFFSET    9
-#define    RTL8367C_MAC_ACTIVE_H_MASK    0xE00
-#define    RTL8367C_FORCE_MAC_ACTIVE_OFFSET    8
-#define    RTL8367C_FORCE_MAC_ACTIVE_MASK    0x100
-#define    RTL8367C_MAC_ACTIVE_OFFSET    0
-#define    RTL8367C_MAC_ACTIVE_MASK    0xFF
-
-#define    RTL8367C_REG_SERDES_RESULT    0x13ef
-#define    RTL8367C_FIB100_DET_1_OFFSET    12
-#define    RTL8367C_FIB100_DET_1_MASK    0x1000
-#define    RTL8367C_FIB_ISO_1_OFFSET    11
-#define    RTL8367C_FIB_ISO_1_MASK    0x800
-#define    RTL8367C_SDS_ANFAULT_1_OFFSET    10
-#define    RTL8367C_SDS_ANFAULT_1_MASK    0x400
-#define    RTL8367C_SDS_INTB_1_OFFSET    9
-#define    RTL8367C_SDS_INTB_1_MASK    0x200
-#define    RTL8367C_SDS_LINK_OK_1_OFFSET    8
-#define    RTL8367C_SDS_LINK_OK_1_MASK    0x100
-#define    RTL8367C_FIB100_DET_OFFSET    4
-#define    RTL8367C_FIB100_DET_MASK    0x10
-#define    RTL8367C_FIB_ISO_OFFSET    3
-#define    RTL8367C_FIB_ISO_MASK    0x8
-#define    RTL8367C_SDS_ANFAULT_OFFSET    2
-#define    RTL8367C_SDS_ANFAULT_MASK    0x4
-#define    RTL8367C_SDS_INTB_OFFSET    1
-#define    RTL8367C_SDS_INTB_MASK    0x2
-#define    RTL8367C_SDS_LINK_OK_OFFSET    0
-#define    RTL8367C_SDS_LINK_OK_MASK    0x1
-
-#define    RTL8367C_REG_CHIP_ECO    0x13f0
-#define    RTL8367C_CFG_CHIP_ECO_OFFSET    1
-#define    RTL8367C_CFG_CHIP_ECO_MASK    0xFFFE
-#define    RTL8367C_CFG_CKOUTEN_OFFSET    0
-#define    RTL8367C_CFG_CKOUTEN_MASK    0x1
-
-#define    RTL8367C_REG_WAKELPI_SLOT_PRD    0x13f1
-#define    RTL8367C_WAKELPI_SLOT_PRD_OFFSET    0
-#define    RTL8367C_WAKELPI_SLOT_PRD_MASK    0x1F
-
-#define    RTL8367C_REG_WAKELPI_SLOT_PG0    0x13f2
-#define    RTL8367C_WAKELPI_SLOT_P1_OFFSET    8
-#define    RTL8367C_WAKELPI_SLOT_P1_MASK    0x1F00
-#define    RTL8367C_WAKELPI_SLOT_P0_OFFSET    0
-#define    RTL8367C_WAKELPI_SLOT_P0_MASK    0x1F
-
-#define    RTL8367C_REG_WAKELPI_SLOT_PG1    0x13f3
-#define    RTL8367C_WAKELPI_SLOT_P3_OFFSET    8
-#define    RTL8367C_WAKELPI_SLOT_P3_MASK    0x1F00
-#define    RTL8367C_WAKELPI_SLOT_P2_OFFSET    0
-#define    RTL8367C_WAKELPI_SLOT_P2_MASK    0x1F
-
-#define    RTL8367C_REG_WAKELPI_SLOT_PG2    0x13f4
-#define    RTL8367C_WAKELPI_SLOT_P5_OFFSET    8
-#define    RTL8367C_WAKELPI_SLOT_P5_MASK    0x1F00
-#define    RTL8367C_WAKELPI_SLOT_P4_OFFSET    0
-#define    RTL8367C_WAKELPI_SLOT_P4_MASK    0x1F
-
-#define    RTL8367C_REG_WAKELPI_SLOT_PG3    0x13f5
-#define    RTL8367C_WAKELPI_SLOT_P7_OFFSET    8
-#define    RTL8367C_WAKELPI_SLOT_P7_MASK    0x1F00
-#define    RTL8367C_WAKELPI_SLOT_P6_OFFSET    0
-#define    RTL8367C_WAKELPI_SLOT_P6_MASK    0x1F
-
-#define    RTL8367C_REG_SYNC_FIFO_0    0x13f6
-#define    RTL8367C_SYNC_FIFO_TX_OFFSET    8
-#define    RTL8367C_SYNC_FIFO_TX_MASK    0x700
-#define    RTL8367C_SYNC_FIFO_RX_OFFSET    0
-#define    RTL8367C_SYNC_FIFO_RX_MASK    0xFF
-
-#define    RTL8367C_REG_SYNC_FIFO_1    0x13f7
-#define    RTL8367C_SYNC_FIFO_RX_ERR_P10_8_OFFSET    11
-#define    RTL8367C_SYNC_FIFO_RX_ERR_P10_8_MASK    0x3800
-#define    RTL8367C_SYNC_FIFO_TX_ERR_OFFSET    8
-#define    RTL8367C_SYNC_FIFO_TX_ERR_MASK    0x700
-#define    RTL8367C_SYNC_FIFO_RX_ERR_OFFSET    0
-#define    RTL8367C_SYNC_FIFO_RX_ERR_MASK    0xFF
-
-#define    RTL8367C_REG_RGM_EEE    0x13f8
-#define    RTL8367C_EXT2_PAD_STOP_EN_OFFSET    14
-#define    RTL8367C_EXT2_PAD_STOP_EN_MASK    0x4000
-#define    RTL8367C_EXT1_PAD_STOP_EN_OFFSET    13
-#define    RTL8367C_EXT1_PAD_STOP_EN_MASK    0x2000
-#define    RTL8367C_EXT0_PAD_STOP_EN_OFFSET    12
-#define    RTL8367C_EXT0_PAD_STOP_EN_MASK    0x1000
-#define    RTL8367C_EXT2_CYCLE_PAD_OFFSET    8
-#define    RTL8367C_EXT2_CYCLE_PAD_MASK    0xF00
-#define    RTL8367C_EXT1_CYCLE_PAD_OFFSET    4
-#define    RTL8367C_EXT1_CYCLE_PAD_MASK    0xF0
-#define    RTL8367C_EXT0_CYCLE_PAD_OFFSET    0
-#define    RTL8367C_EXT0_CYCLE_PAD_MASK    0xF
-
-#define    RTL8367C_REG_EXT_TXC_DLY    0x13f9
-#define    RTL8367C_EXT1_GMII_TX_DELAY_OFFSET    12
-#define    RTL8367C_EXT1_GMII_TX_DELAY_MASK    0x7000
-#define    RTL8367C_EXT0_GMII_TX_DELAY_OFFSET    9
-#define    RTL8367C_EXT0_GMII_TX_DELAY_MASK    0xE00
-#define    RTL8367C_EXT2_RGMII_TX_DELAY_OFFSET    6
-#define    RTL8367C_EXT2_RGMII_TX_DELAY_MASK    0x1C0
-#define    RTL8367C_EXT1_RGMII_TX_DELAY_OFFSET    3
-#define    RTL8367C_EXT1_RGMII_TX_DELAY_MASK    0x38
-#define    RTL8367C_EXT0_RGMII_TX_DELAY_OFFSET    0
-#define    RTL8367C_EXT0_RGMII_TX_DELAY_MASK    0x7
-
-#define    RTL8367C_REG_IO_MISC_CTRL    0x13fa
-#define    RTL8367C_IO_BUZZER_EN_OFFSET    3
-#define    RTL8367C_IO_BUZZER_EN_MASK    0x8
-#define    RTL8367C_IO_INTRPT_EN_OFFSET    2
-#define    RTL8367C_IO_INTRPT_EN_MASK    0x4
-#define    RTL8367C_IO_NRESTORE_EN_OFFSET    1
-#define    RTL8367C_IO_NRESTORE_EN_MASK    0x2
-#define    RTL8367C_IO_UART_EN_OFFSET    0
-#define    RTL8367C_IO_UART_EN_MASK    0x1
-
-#define    RTL8367C_REG_CHIP_DUMMY_NO    0x13fb
-#define    RTL8367C_CHIP_DUMMY_NO_OFFSET    0
-#define    RTL8367C_CHIP_DUMMY_NO_MASK    0xF
-
-#define    RTL8367C_REG_RC_CALIB_CFG    0x13fc
-#define    RTL8367C_TRIG_BURN_EFUSE_OFFSET    9
-#define    RTL8367C_TRIG_BURN_EFUSE_MASK    0x200
-#define    RTL8367C_AMP_CALIB_FAIL_OFFSET    8
-#define    RTL8367C_AMP_CALIB_FAIL_MASK    0x100
-#define    RTL8367C_R_CALIB_FAIL_OFFSET    7
-#define    RTL8367C_R_CALIB_FAIL_MASK    0x80
-#define    RTL8367C_CFG_CALIB_MODE_OFFSET    6
-#define    RTL8367C_CFG_CALIB_MODE_MASK    0x40
-#define    RTL8367C_CENTER_PORT_SEL_OFFSET    3
-#define    RTL8367C_CENTER_PORT_SEL_MASK    0x38
-#define    RTL8367C_CALIB_FINISH_OFFSET    2
-#define    RTL8367C_CALIB_FINISH_MASK    0x4
-#define    RTL8367C_CFG_CALIB_OPTION_OFFSET    1
-#define    RTL8367C_CFG_CALIB_OPTION_MASK    0x2
-#define    RTL8367C_CFG_CALIB_EN_OFFSET    0
-#define    RTL8367C_CFG_CALIB_EN_MASK    0x1
-
-#define    RTL8367C_REG_WAKELPI_SLOT_PG4    0x13fd
-#define    RTL8367C_WAKELPI_SLOT_P9_OFFSET    8
-#define    RTL8367C_WAKELPI_SLOT_P9_MASK    0x1F00
-#define    RTL8367C_WAKELPI_SLOT_P8_OFFSET    0
-#define    RTL8367C_WAKELPI_SLOT_P8_MASK    0x1F
-
-#define    RTL8367C_REG_WAKELPI_SLOT_PG5    0x13fe
-#define    RTL8367C_WAKELPI_SLOT_PG5_OFFSET    0
-#define    RTL8367C_WAKELPI_SLOT_PG5_MASK    0x1F
-
-/* (16'h1400)mtrpool_reg */
-
-#define    RTL8367C_REG_METER0_RATE_CTRL0    0x1400
-
-#define    RTL8367C_REG_METER0_RATE_CTRL1    0x1401
-#define    RTL8367C_METER0_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER0_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER1_RATE_CTRL0    0x1402
-
-#define    RTL8367C_REG_METER1_RATE_CTRL1    0x1403
-#define    RTL8367C_METER1_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER1_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER2_RATE_CTRL0    0x1404
-
-#define    RTL8367C_REG_METER2_RATE_CTRL1    0x1405
-#define    RTL8367C_METER2_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER2_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER3_RATE_CTRL0    0x1406
-
-#define    RTL8367C_REG_METER3_RATE_CTRL1    0x1407
-#define    RTL8367C_METER3_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER3_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER4_RATE_CTRL0    0x1408
-
-#define    RTL8367C_REG_METER4_RATE_CTRL1    0x1409
-#define    RTL8367C_METER4_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER4_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER5_RATE_CTRL0    0x140a
-
-#define    RTL8367C_REG_METER5_RATE_CTRL1    0x140b
-#define    RTL8367C_METER5_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER5_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER6_RATE_CTRL0    0x140c
-
-#define    RTL8367C_REG_METER6_RATE_CTRL1    0x140d
-#define    RTL8367C_METER6_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER6_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER7_RATE_CTRL0    0x140e
-
-#define    RTL8367C_REG_METER7_RATE_CTRL1    0x140f
-#define    RTL8367C_METER7_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER7_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER8_RATE_CTRL0    0x1410
-
-#define    RTL8367C_REG_METER8_RATE_CTRL1    0x1411
-#define    RTL8367C_METER8_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER8_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER9_RATE_CTRL0    0x1412
-
-#define    RTL8367C_REG_METER9_RATE_CTRL1    0x1413
-#define    RTL8367C_METER9_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER9_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER10_RATE_CTRL0    0x1414
-
-#define    RTL8367C_REG_METER10_RATE_CTRL1    0x1415
-#define    RTL8367C_METER10_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER10_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER11_RATE_CTRL0    0x1416
-
-#define    RTL8367C_REG_METER11_RATE_CTRL1    0x1417
-#define    RTL8367C_METER11_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER11_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER12_RATE_CTRL0    0x1418
-
-#define    RTL8367C_REG_METER12_RATE_CTRL1    0x1419
-#define    RTL8367C_METER12_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER12_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER13_RATE_CTRL0    0x141a
-
-#define    RTL8367C_REG_METER13_RATE_CTRL1    0x141b
-#define    RTL8367C_METER13_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER13_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER14_RATE_CTRL0    0x141c
-
-#define    RTL8367C_REG_METER14_RATE_CTRL1    0x141d
-#define    RTL8367C_METER14_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER14_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER15_RATE_CTRL0    0x141e
-
-#define    RTL8367C_REG_METER15_RATE_CTRL1    0x141f
-#define    RTL8367C_METER15_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER15_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER16_RATE_CTRL0    0x1420
-
-#define    RTL8367C_REG_METER16_RATE_CTRL1    0x1421
-#define    RTL8367C_METER16_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER16_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER17_RATE_CTRL0    0x1422
-
-#define    RTL8367C_REG_METER17_RATE_CTRL1    0x1423
-#define    RTL8367C_METER17_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER17_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER18_RATE_CTRL0    0x1424
-
-#define    RTL8367C_REG_METER18_RATE_CTRL1    0x1425
-#define    RTL8367C_METER18_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER18_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER19_RATE_CTRL0    0x1426
-
-#define    RTL8367C_REG_METER19_RATE_CTRL1    0x1427
-#define    RTL8367C_METER19_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER19_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER20_RATE_CTRL0    0x1428
-
-#define    RTL8367C_REG_METER20_RATE_CTRL1    0x1429
-#define    RTL8367C_METER20_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER20_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER21_RATE_CTRL0    0x142a
-
-#define    RTL8367C_REG_METER21_RATE_CTRL1    0x142b
-#define    RTL8367C_METER21_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER21_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER22_RATE_CTRL0    0x142c
-
-#define    RTL8367C_REG_METER22_RATE_CTRL1    0x142d
-#define    RTL8367C_METER22_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER22_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER23_RATE_CTRL0    0x142e
-
-#define    RTL8367C_REG_METER23_RATE_CTRL1    0x142f
-#define    RTL8367C_METER23_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER23_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER24_RATE_CTRL0    0x1430
-
-#define    RTL8367C_REG_METER24_RATE_CTRL1    0x1431
-#define    RTL8367C_METER24_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER24_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER25_RATE_CTRL0    0x1432
-
-#define    RTL8367C_REG_METER25_RATE_CTRL1    0x1433
-#define    RTL8367C_METER25_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER25_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER26_RATE_CTRL0    0x1434
-
-#define    RTL8367C_REG_METER26_RATE_CTRL1    0x1435
-#define    RTL8367C_METER26_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER26_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER27_RATE_CTRL0    0x1436
-
-#define    RTL8367C_REG_METER27_RATE_CTRL1    0x1437
-#define    RTL8367C_METER27_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER27_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER28_RATE_CTRL0    0x1438
-
-#define    RTL8367C_REG_METER28_RATE_CTRL1    0x1439
-#define    RTL8367C_METER28_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER28_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER29_RATE_CTRL0    0x143a
-
-#define    RTL8367C_REG_METER29_RATE_CTRL1    0x143b
-#define    RTL8367C_METER29_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER29_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER30_RATE_CTRL0    0x143c
-
-#define    RTL8367C_REG_METER30_RATE_CTRL1    0x143d
-#define    RTL8367C_METER30_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER30_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER31_RATE_CTRL0    0x143e
-
-#define    RTL8367C_REG_METER31_RATE_CTRL1    0x143f
-#define    RTL8367C_METER31_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER31_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER_MODE_SETTING0    0x1440
-
-#define    RTL8367C_REG_METER_MODE_SETTING1    0x1441
-
-#define    RTL8367C_REG_METER_MODE_TOKEN_CFG    0x1442
-#define    RTL8367C_METER_MODE_TOKEN_CFG_OFFSET    0
-#define    RTL8367C_METER_MODE_TOKEN_CFG_MASK    0x7FF
-
-#define    RTL8367C_REG_METER0_BUCKET_SIZE    0x1600
-
-#define    RTL8367C_REG_METER1_BUCKET_SIZE    0x1601
-
-#define    RTL8367C_REG_METER2_BUCKET_SIZE    0x1602
-
-#define    RTL8367C_REG_METER3_BUCKET_SIZE    0x1603
-
-#define    RTL8367C_REG_METER4_BUCKET_SIZE    0x1604
-
-#define    RTL8367C_REG_METER5_BUCKET_SIZE    0x1605
-
-#define    RTL8367C_REG_METER6_BUCKET_SIZE    0x1606
-
-#define    RTL8367C_REG_METER7_BUCKET_SIZE    0x1607
-
-#define    RTL8367C_REG_METER8_BUCKET_SIZE    0x1608
-
-#define    RTL8367C_REG_METER9_BUCKET_SIZE    0x1609
-
-#define    RTL8367C_REG_METER10_BUCKET_SIZE    0x160a
-
-#define    RTL8367C_REG_METER11_BUCKET_SIZE    0x160b
-
-#define    RTL8367C_REG_METER12_BUCKET_SIZE    0x160c
-
-#define    RTL8367C_REG_METER13_BUCKET_SIZE    0x160d
-
-#define    RTL8367C_REG_METER14_BUCKET_SIZE    0x160e
-
-#define    RTL8367C_REG_METER15_BUCKET_SIZE    0x160f
-
-#define    RTL8367C_REG_METER16_BUCKET_SIZE    0x1610
-
-#define    RTL8367C_REG_METER17_BUCKET_SIZE    0x1611
-
-#define    RTL8367C_REG_METER18_BUCKET_SIZE    0x1612
-
-#define    RTL8367C_REG_METER19_BUCKET_SIZE    0x1613
-
-#define    RTL8367C_REG_METER20_BUCKET_SIZE    0x1614
-
-#define    RTL8367C_REG_METER21_BUCKET_SIZE    0x1615
-
-#define    RTL8367C_REG_METER22_BUCKET_SIZE    0x1616
-
-#define    RTL8367C_REG_METER23_BUCKET_SIZE    0x1617
-
-#define    RTL8367C_REG_METER24_BUCKET_SIZE    0x1618
-
-#define    RTL8367C_REG_METER25_BUCKET_SIZE    0x1619
-
-#define    RTL8367C_REG_METER26_BUCKET_SIZE    0x161a
-
-#define    RTL8367C_REG_METER27_BUCKET_SIZE    0x161b
-
-#define    RTL8367C_REG_METER28_BUCKET_SIZE    0x161c
-
-#define    RTL8367C_REG_METER29_BUCKET_SIZE    0x161d
-
-#define    RTL8367C_REG_METER30_BUCKET_SIZE    0x161e
-
-#define    RTL8367C_REG_METER31_BUCKET_SIZE    0x161f
-
-#define    RTL8367C_REG_METER_CTRL0    0x1700
-#define    RTL8367C_METER_OP_OFFSET    8
-#define    RTL8367C_METER_OP_MASK    0x100
-#define    RTL8367C_METER_TICK_OFFSET    0
-#define    RTL8367C_METER_TICK_MASK    0xFF
-
-#define    RTL8367C_REG_METER_CTRL1    0x1701
-#define    RTL8367C_METER_CTRL1_OFFSET    0
-#define    RTL8367C_METER_CTRL1_MASK    0xFF
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR0    0x1702
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR1    0x1703
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR0_8051    0x1704
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR1_8051    0x1705
-
-#define    RTL8367C_REG_METER_IFG_CTRL0    0x1712
-#define    RTL8367C_METER15_IFG_OFFSET    15
-#define    RTL8367C_METER15_IFG_MASK    0x8000
-#define    RTL8367C_METER14_IFG_OFFSET    14
-#define    RTL8367C_METER14_IFG_MASK    0x4000
-#define    RTL8367C_METER13_IFG_OFFSET    13
-#define    RTL8367C_METER13_IFG_MASK    0x2000
-#define    RTL8367C_METER12_IFG_OFFSET    12
-#define    RTL8367C_METER12_IFG_MASK    0x1000
-#define    RTL8367C_METER11_IFG_OFFSET    11
-#define    RTL8367C_METER11_IFG_MASK    0x800
-#define    RTL8367C_METER10_IFG_OFFSET    10
-#define    RTL8367C_METER10_IFG_MASK    0x400
-#define    RTL8367C_METER9_IFG_OFFSET    9
-#define    RTL8367C_METER9_IFG_MASK    0x200
-#define    RTL8367C_METER8_IFG_OFFSET    8
-#define    RTL8367C_METER8_IFG_MASK    0x100
-#define    RTL8367C_METER7_IFG_OFFSET    7
-#define    RTL8367C_METER7_IFG_MASK    0x80
-#define    RTL8367C_METER6_IFG_OFFSET    6
-#define    RTL8367C_METER6_IFG_MASK    0x40
-#define    RTL8367C_METER5_IFG_OFFSET    5
-#define    RTL8367C_METER5_IFG_MASK    0x20
-#define    RTL8367C_METER4_IFG_OFFSET    4
-#define    RTL8367C_METER4_IFG_MASK    0x10
-#define    RTL8367C_METER3_IFG_OFFSET    3
-#define    RTL8367C_METER3_IFG_MASK    0x8
-#define    RTL8367C_METER2_IFG_OFFSET    2
-#define    RTL8367C_METER2_IFG_MASK    0x4
-#define    RTL8367C_METER1_IFG_OFFSET    1
-#define    RTL8367C_METER1_IFG_MASK    0x2
-#define    RTL8367C_METER0_IFG_OFFSET    0
-#define    RTL8367C_METER0_IFG_MASK    0x1
-
-#define    RTL8367C_REG_METER_IFG_CTRL1    0x1713
-#define    RTL8367C_METER31_IFG_OFFSET    15
-#define    RTL8367C_METER31_IFG_MASK    0x8000
-#define    RTL8367C_METER30_IFG_OFFSET    14
-#define    RTL8367C_METER30_IFG_MASK    0x4000
-#define    RTL8367C_METER29_IFG_OFFSET    13
-#define    RTL8367C_METER29_IFG_MASK    0x2000
-#define    RTL8367C_METER28_IFG_OFFSET    12
-#define    RTL8367C_METER28_IFG_MASK    0x1000
-#define    RTL8367C_METER27_IFG_OFFSET    11
-#define    RTL8367C_METER27_IFG_MASK    0x800
-#define    RTL8367C_METER26_IFG_OFFSET    10
-#define    RTL8367C_METER26_IFG_MASK    0x400
-#define    RTL8367C_METER25_IFG_OFFSET    9
-#define    RTL8367C_METER25_IFG_MASK    0x200
-#define    RTL8367C_METER24_IFG_OFFSET    8
-#define    RTL8367C_METER24_IFG_MASK    0x100
-#define    RTL8367C_METER23_IFG_OFFSET    7
-#define    RTL8367C_METER23_IFG_MASK    0x80
-#define    RTL8367C_METER22_IFG_OFFSET    6
-#define    RTL8367C_METER22_IFG_MASK    0x40
-#define    RTL8367C_METER21_IFG_OFFSET    5
-#define    RTL8367C_METER21_IFG_MASK    0x20
-#define    RTL8367C_METER20_IFG_OFFSET    4
-#define    RTL8367C_METER20_IFG_MASK    0x10
-#define    RTL8367C_METER19_IFG_OFFSET    3
-#define    RTL8367C_METER19_IFG_MASK    0x8
-#define    RTL8367C_METER18_IFG_OFFSET    2
-#define    RTL8367C_METER18_IFG_MASK    0x4
-#define    RTL8367C_METER17_IFG_OFFSET    1
-#define    RTL8367C_METER17_IFG_MASK    0x2
-#define    RTL8367C_METER16_IFG_OFFSET    0
-#define    RTL8367C_METER16_IFG_MASK    0x1
-
-#define    RTL8367C_REG_METER_CTRL2    0x1722
-#define    RTL8367C_cfg_mtr_tick_8g_OFFSET    8
-#define    RTL8367C_cfg_mtr_tick_8g_MASK    0xFF00
-#define    RTL8367C_cfg_mtr_dec_cnt_8g_OFFSET    0
-#define    RTL8367C_cfg_mtr_dec_cnt_8g_MASK    0xFF
-
-#define    RTL8367C_REG_DUMMY_1723    0x1723
-
-#define    RTL8367C_REG_DUMMY_1724    0x1724
-
-#define    RTL8367C_REG_DUMMY_1725    0x1725
-
-#define    RTL8367C_REG_DUMMY_1726    0x1726
-
-#define    RTL8367C_REG_DUMMY_1727    0x1727
-
-#define    RTL8367C_REG_DUMMY_1728    0x1728
-
-#define    RTL8367C_REG_DUMMY_1729    0x1729
-
-#define    RTL8367C_REG_DUMMY_172A    0x172a
-
-#define    RTL8367C_REG_DUMMY_172B    0x172b
-
-#define    RTL8367C_REG_DUMMY_172C    0x172c
-
-#define    RTL8367C_REG_DUMMY_172D    0x172d
-
-#define    RTL8367C_REG_DUMMY_172E    0x172e
-
-#define    RTL8367C_REG_DUMMY_172F    0x172f
-
-#define    RTL8367C_REG_DUMMY_1730    0x1730
-
-#define    RTL8367C_REG_DUMMY_1731    0x1731
-
-#define    RTL8367C_REG_METER32_RATE_CTRL0    0x1740
-
-#define    RTL8367C_REG_METER32_RATE_CTRL1    0x1741
-#define    RTL8367C_METER32_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER32_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER33_RATE_CTRL0    0x1742
-
-#define    RTL8367C_REG_METER33_RATE_CTRL1    0x1743
-#define    RTL8367C_METER33_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER33_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER34_RATE_CTRL0    0x1744
-
-#define    RTL8367C_REG_METER34_RATE_CTRL1    0x1745
-#define    RTL8367C_METER34_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER34_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER35_RATE_CTRL0    0x1746
-
-#define    RTL8367C_REG_METER35_RATE_CTRL1    0x1747
-#define    RTL8367C_METER35_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER35_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER36_RATE_CTRL0    0x1748
-
-#define    RTL8367C_REG_METER36_RATE_CTRL1    0x1749
-#define    RTL8367C_METER36_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER36_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER37_RATE_CTRL0    0x174a
-
-#define    RTL8367C_REG_METER37_RATE_CTRL1    0x174b
-#define    RTL8367C_METER37_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER37_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER38_RATE_CTRL0    0x174c
-
-#define    RTL8367C_REG_METER38_RATE_CTRL1    0x174d
-#define    RTL8367C_METER38_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER38_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER39_RATE_CTRL0    0x174e
-
-#define    RTL8367C_REG_METER39_RATE_CTRL1    0x174f
-#define    RTL8367C_METER39_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER39_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER40_RATE_CTRL0    0x1750
-
-#define    RTL8367C_REG_METER40_RATE_CTRL1    0x1751
-#define    RTL8367C_METER40_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER40_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER41_RATE_CTRL0    0x1752
-
-#define    RTL8367C_REG_METER41_RATE_CTRL1    0x1753
-#define    RTL8367C_METER41_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER41_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER42_RATE_CTRL0    0x1754
-
-#define    RTL8367C_REG_METER42_RATE_CTRL1    0x1755
-#define    RTL8367C_METER42_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER42_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER43_RATE_CTRL0    0x1756
-
-#define    RTL8367C_REG_METER43_RATE_CTRL1    0x1757
-#define    RTL8367C_METER43_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER43_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER44_RATE_CTRL0    0x1758
-
-#define    RTL8367C_REG_METER44_RATE_CTRL1    0x1759
-#define    RTL8367C_METER44_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER44_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER45_RATE_CTRL0    0x175a
-
-#define    RTL8367C_REG_METER45_RATE_CTRL1    0x175b
-#define    RTL8367C_METER45_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER45_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER46_RATE_CTRL0    0x175c
-
-#define    RTL8367C_REG_METER46_RATE_CTRL1    0x175d
-#define    RTL8367C_METER46_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER46_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER47_RATE_CTRL0    0x175e
-
-#define    RTL8367C_REG_METER47_RATE_CTRL1    0x175f
-#define    RTL8367C_METER47_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER47_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER48_RATE_CTRL0    0x1760
-
-#define    RTL8367C_REG_METER48_RATE_CTRL1    0x1761
-#define    RTL8367C_METER48_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER48_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER49_RATE_CTRL0    0x1762
-
-#define    RTL8367C_REG_METER49_RATE_CTRL1    0x1763
-#define    RTL8367C_METER49_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER49_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER50_RATE_CTRL0    0x1764
-
-#define    RTL8367C_REG_METER50_RATE_CTRL1    0x1765
-#define    RTL8367C_METER50_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER50_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER51_RATE_CTRL0    0x1766
-
-#define    RTL8367C_REG_METER51_RATE_CTRL1    0x1767
-#define    RTL8367C_METER51_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER51_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER52_RATE_CTRL0    0x1768
-
-#define    RTL8367C_REG_METER52_RATE_CTRL1    0x1769
-#define    RTL8367C_METER52_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER52_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER53_RATE_CTRL0    0x176a
-
-#define    RTL8367C_REG_METER53_RATE_CTRL1    0x176b
-#define    RTL8367C_METER53_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER53_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER54_RATE_CTRL0    0x176c
-
-#define    RTL8367C_REG_METER54_RATE_CTRL1    0x176d
-#define    RTL8367C_METER54_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER54_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER55_RATE_CTRL0    0x176e
-
-#define    RTL8367C_REG_METER55_RATE_CTRL1    0x176f
-#define    RTL8367C_METER55_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER55_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER56_RATE_CTRL0    0x1770
-
-#define    RTL8367C_REG_METER56_RATE_CTRL1    0x1771
-#define    RTL8367C_METER56_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER56_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER57_RATE_CTRL0    0x1772
-
-#define    RTL8367C_REG_METER57_RATE_CTRL1    0x1773
-#define    RTL8367C_METER57_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER57_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER58_RATE_CTRL0    0x1774
-
-#define    RTL8367C_REG_METER58_RATE_CTRL1    0x1775
-#define    RTL8367C_METER58_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER58_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER59_RATE_CTRL0    0x1776
-
-#define    RTL8367C_REG_METER59_RATE_CTRL1    0x1777
-#define    RTL8367C_METER59_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER59_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER60_RATE_CTRL0    0x1778
-
-#define    RTL8367C_REG_METER60_RATE_CTRL1    0x1779
-#define    RTL8367C_METER60_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER60_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER61_RATE_CTRL0    0x177a
-
-#define    RTL8367C_REG_METER61_RATE_CTRL1    0x177b
-#define    RTL8367C_METER61_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER61_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER62_RATE_CTRL0    0x177c
-
-#define    RTL8367C_REG_METER62_RATE_CTRL1    0x177d
-#define    RTL8367C_METER62_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER62_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER63_RATE_CTRL0    0x177e
-
-#define    RTL8367C_REG_METER63_RATE_CTRL1    0x177f
-#define    RTL8367C_METER63_RATE_CTRL1_OFFSET    0
-#define    RTL8367C_METER63_RATE_CTRL1_MASK    0x7
-
-#define    RTL8367C_REG_METER_MODE_SETTING2    0x1780
-
-#define    RTL8367C_REG_METER_MODE_SETTING3    0x1781
-
-#define    RTL8367C_REG_METER32_BUCKET_SIZE    0x1790
-
-#define    RTL8367C_REG_METER33_BUCKET_SIZE    0x1791
-
-#define    RTL8367C_REG_METER34_BUCKET_SIZE    0x1792
-
-#define    RTL8367C_REG_METER35_BUCKET_SIZE    0x1793
-
-#define    RTL8367C_REG_METER36_BUCKET_SIZE    0x1794
-
-#define    RTL8367C_REG_METER37_BUCKET_SIZE    0x1795
-
-#define    RTL8367C_REG_METER38_BUCKET_SIZE    0x1796
-
-#define    RTL8367C_REG_METER39_BUCKET_SIZE    0x1797
-
-#define    RTL8367C_REG_METER40_BUCKET_SIZE    0x1798
-
-#define    RTL8367C_REG_METER41_BUCKET_SIZE    0x1799
-
-#define    RTL8367C_REG_METER42_BUCKET_SIZE    0x179a
-
-#define    RTL8367C_REG_METER43_BUCKET_SIZE    0x179b
-
-#define    RTL8367C_REG_METER44_BUCKET_SIZE    0x179c
-
-#define    RTL8367C_REG_METER45_BUCKET_SIZE    0x179d
-
-#define    RTL8367C_REG_METER46_BUCKET_SIZE    0x179e
-
-#define    RTL8367C_REG_METER47_BUCKET_SIZE    0x179f
-
-#define    RTL8367C_REG_METER48_BUCKET_SIZE    0x17a0
-
-#define    RTL8367C_REG_METER49_BUCKET_SIZE    0x17a1
-
-#define    RTL8367C_REG_METER50_BUCKET_SIZE    0x17a2
-
-#define    RTL8367C_REG_METER51_BUCKET_SIZE    0x17a3
-
-#define    RTL8367C_REG_METER52_BUCKET_SIZE    0x17a4
-
-#define    RTL8367C_REG_METER53_BUCKET_SIZE    0x17a5
-
-#define    RTL8367C_REG_METER54_BUCKET_SIZE    0x17a6
-
-#define    RTL8367C_REG_METER55_BUCKET_SIZE    0x17a7
-
-#define    RTL8367C_REG_METER56_BUCKET_SIZE    0x17a8
-
-#define    RTL8367C_REG_METER57_BUCKET_SIZE    0x17a9
-
-#define    RTL8367C_REG_METER58_BUCKET_SIZE    0x17aa
-
-#define    RTL8367C_REG_METER59_BUCKET_SIZE    0x17ab
-
-#define    RTL8367C_REG_METER60_BUCKET_SIZE    0x17ac
-
-#define    RTL8367C_REG_METER61_BUCKET_SIZE    0x17ad
-
-#define    RTL8367C_REG_METER62_BUCKET_SIZE    0x17ae
-
-#define    RTL8367C_REG_METER63_BUCKET_SIZE    0x17af
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR2    0x17b0
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR3    0x17b1
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR2_8051    0x17b2
-
-#define    RTL8367C_REG_METER_OVERRATE_INDICATOR3_8051    0x17b3
-
-#define    RTL8367C_REG_METER_IFG_CTRL2    0x17b4
-#define    RTL8367C_METER47_IFG_OFFSET    15
-#define    RTL8367C_METER47_IFG_MASK    0x8000
-#define    RTL8367C_METER46_IFG_OFFSET    14
-#define    RTL8367C_METER46_IFG_MASK    0x4000
-#define    RTL8367C_METER45_IFG_OFFSET    13
-#define    RTL8367C_METER45_IFG_MASK    0x2000
-#define    RTL8367C_METER44_IFG_OFFSET    12
-#define    RTL8367C_METER44_IFG_MASK    0x1000
-#define    RTL8367C_METER43_IFG_OFFSET    11
-#define    RTL8367C_METER43_IFG_MASK    0x800
-#define    RTL8367C_METER42_IFG_OFFSET    10
-#define    RTL8367C_METER42_IFG_MASK    0x400
-#define    RTL8367C_METER41_IFG_OFFSET    9
-#define    RTL8367C_METER41_IFG_MASK    0x200
-#define    RTL8367C_METER40_IFG_OFFSET    8
-#define    RTL8367C_METER40_IFG_MASK    0x100
-#define    RTL8367C_METER39_IFG_OFFSET    7
-#define    RTL8367C_METER39_IFG_MASK    0x80
-#define    RTL8367C_METER38_IFG_OFFSET    6
-#define    RTL8367C_METER38_IFG_MASK    0x40
-#define    RTL8367C_METER37_IFG_OFFSET    5
-#define    RTL8367C_METER37_IFG_MASK    0x20
-#define    RTL8367C_METER36_IFG_OFFSET    4
-#define    RTL8367C_METER36_IFG_MASK    0x10
-#define    RTL8367C_METER35_IFG_OFFSET    3
-#define    RTL8367C_METER35_IFG_MASK    0x8
-#define    RTL8367C_METER34_IFG_OFFSET    2
-#define    RTL8367C_METER34_IFG_MASK    0x4
-#define    RTL8367C_METER33_IFG_OFFSET    1
-#define    RTL8367C_METER33_IFG_MASK    0x2
-#define    RTL8367C_METER32_IFG_OFFSET    0
-#define    RTL8367C_METER32_IFG_MASK    0x1
-
-#define    RTL8367C_REG_METER_IFG_CTRL3    0x17b5
-#define    RTL8367C_METER63_IFG_OFFSET    15
-#define    RTL8367C_METER63_IFG_MASK    0x8000
-#define    RTL8367C_METER62_IFG_OFFSET    14
-#define    RTL8367C_METER62_IFG_MASK    0x4000
-#define    RTL8367C_METER61_IFG_OFFSET    13
-#define    RTL8367C_METER61_IFG_MASK    0x2000
-#define    RTL8367C_METER60_IFG_OFFSET    12
-#define    RTL8367C_METER60_IFG_MASK    0x1000
-#define    RTL8367C_METER59_IFG_OFFSET    11
-#define    RTL8367C_METER59_IFG_MASK    0x800
-#define    RTL8367C_METER58_IFG_OFFSET    10
-#define    RTL8367C_METER58_IFG_MASK    0x400
-#define    RTL8367C_METER57_IFG_OFFSET    9
-#define    RTL8367C_METER57_IFG_MASK    0x200
-#define    RTL8367C_METER56_IFG_OFFSET    8
-#define    RTL8367C_METER56_IFG_MASK    0x100
-#define    RTL8367C_METER55_IFG_OFFSET    7
-#define    RTL8367C_METER55_IFG_MASK    0x80
-#define    RTL8367C_METER54_IFG_OFFSET    6
-#define    RTL8367C_METER54_IFG_MASK    0x40
-#define    RTL8367C_METER53_IFG_OFFSET    5
-#define    RTL8367C_METER53_IFG_MASK    0x20
-#define    RTL8367C_METER52_IFG_OFFSET    4
-#define    RTL8367C_METER52_IFG_MASK    0x10
-#define    RTL8367C_METER51_IFG_OFFSET    3
-#define    RTL8367C_METER51_IFG_MASK    0x8
-#define    RTL8367C_METER50_IFG_OFFSET    2
-#define    RTL8367C_METER50_IFG_MASK    0x4
-#define    RTL8367C_METER49_IFG_OFFSET    1
-#define    RTL8367C_METER49_IFG_MASK    0x2
-#define    RTL8367C_METER48_IFG_OFFSET    0
-#define    RTL8367C_METER48_IFG_MASK    0x1
-
-#define    RTL8367C_REG_METER_MISC    0x17b6
-#define    RTL8367C_METER_MISC_OFFSET    0
-#define    RTL8367C_METER_MISC_MASK    0x1
-
-/* (16'h1800)8051_RLDP_EEE_reg */
-
-#define    RTL8367C_REG_EEELLDP_CTRL0    0x1820
-#define    RTL8367C_EEELLDP_SUBTYPE_OFFSET    6
-#define    RTL8367C_EEELLDP_SUBTYPE_MASK    0x3FC0
-#define    RTL8367C_EEELLDP_TRAP_8051_OFFSET    2
-#define    RTL8367C_EEELLDP_TRAP_8051_MASK    0x4
-#define    RTL8367C_EEELLDP_TRAP_CPU_OFFSET    1
-#define    RTL8367C_EEELLDP_TRAP_CPU_MASK    0x2
-#define    RTL8367C_EEELLDP_ENABLE_OFFSET    0
-#define    RTL8367C_EEELLDP_ENABLE_MASK    0x1
-
-#define    RTL8367C_REG_EEELLDP_PMSK    0x1822
-#define    RTL8367C_EEELLDP_PMSK_OFFSET    0
-#define    RTL8367C_EEELLDP_PMSK_MASK    0x7FF
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_08    0x1843
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_07    0x1844
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_06    0x1845
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_05    0x1846
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_04    0x1847
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_03    0x1848
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_02    0x1849
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_01    0x184a
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P00_00    0x184b
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_08    0x184c
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_07    0x184d
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_06    0x184e
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_05    0x184f
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_04    0x1850
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_03    0x1851
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_02    0x1852
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_01    0x1853
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P01_00    0x1854
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_08    0x1855
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_07    0x1856
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_06    0x1857
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_05    0x1858
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_04    0x1859
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_03    0x185a
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_02    0x185b
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_01    0x185c
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P02_00    0x185d
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_08    0x185e
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_07    0x185f
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_06    0x1860
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_05    0x1861
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_04    0x1862
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_03    0x1863
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_02    0x1864
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_01    0x1865
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P03_00    0x1866
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_08    0x1867
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_07    0x1868
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_06    0x1869
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_05    0x186a
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_04    0x186b
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_03    0x186c
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_02    0x186d
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_01    0x186e
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P04_00    0x186f
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_08    0x1870
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_07    0x1871
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_06    0x1872
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_05    0x1873
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_04    0x1874
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_03    0x1875
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_02    0x1876
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_01    0x1877
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P05_00    0x1878
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_08    0x1879
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_07    0x187a
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_06    0x187b
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_05    0x187c
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_04    0x187d
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_03    0x187e
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_02    0x187f
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_01    0x1880
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P06_00    0x1881
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_08    0x1882
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_07    0x1883
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_06    0x1884
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_05    0x1885
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_04    0x1886
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_03    0x1887
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_02    0x1888
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_01    0x1889
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P07_00    0x188a
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_08    0x188b
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_07    0x188c
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_06    0x188d
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_05    0x188e
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_04    0x188f
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_03    0x1890
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_02    0x1891
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_01    0x1892
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P08_00    0x1893
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_08    0x1894
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_07    0x1895
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_06    0x1896
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_05    0x1897
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_04    0x1898
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_03    0x1899
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_02    0x189a
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_01    0x189b
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P09_00    0x189c
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_08    0x189d
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_07    0x189e
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_06    0x189f
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_05    0x18a0
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_04    0x18a1
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_03    0x18a2
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_02    0x18a3
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_01    0x18a4
-
-#define    RTL8367C_REG_EEELLDP_RX_VALUE_P10_00    0x18a5
-
-#define    RTL8367C_REG_RLDP_CTRL0    0x18e0
-#define    RTL8367C_RLDP_TRIGGER_MODE_OFFSET    14
-#define    RTL8367C_RLDP_TRIGGER_MODE_MASK    0x4000
-#define    RTL8367C_RLDP_8051_LOOP_PORTMSK_OFFSET    6
-#define    RTL8367C_RLDP_8051_LOOP_PORTMSK_MASK    0x3FC0
-#define    RTL8367C_RLPP_8051_TRAP_OFFSET    5
-#define    RTL8367C_RLPP_8051_TRAP_MASK    0x20
-#define    RTL8367C_RLDP_INDICATOR_SOURCE_OFFSET    4
-#define    RTL8367C_RLDP_INDICATOR_SOURCE_MASK    0x10
-#define    RTL8367C_RLDP_GEN_RANDOM_OFFSET    3
-#define    RTL8367C_RLDP_GEN_RANDOM_MASK    0x8
-#define    RTL8367C_RLDP_COMP_ID_OFFSET    2
-#define    RTL8367C_RLDP_COMP_ID_MASK    0x4
-#define    RTL8367C_RLDP_8051_ENABLE_OFFSET    1
-#define    RTL8367C_RLDP_8051_ENABLE_MASK    0x2
-#define    RTL8367C_RLDP_ENABLE_OFFSET    0
-#define    RTL8367C_RLDP_ENABLE_MASK    0x1
-
-#define    RTL8367C_REG_RLDP_CTRL1    0x18e1
-#define    RTL8367C_RLDP_RETRY_COUNT_LOOPSTATE_OFFSET    8
-#define    RTL8367C_RLDP_RETRY_COUNT_LOOPSTATE_MASK    0xFF00
-#define    RTL8367C_RLDP_RETRY_COUNT_CHKSTATE_OFFSET    0
-#define    RTL8367C_RLDP_RETRY_COUNT_CHKSTATE_MASK    0xFF
-
-#define    RTL8367C_REG_RLDP_CTRL2    0x18e2
-
-#define    RTL8367C_REG_RLDP_CTRL3    0x18e3
-
-#define    RTL8367C_REG_RLDP_CTRL4    0x18e4
-#define    RTL8367C_RLDP_CTRL4_OFFSET    0
-#define    RTL8367C_RLDP_CTRL4_MASK    0x7FF
-
-#define    RTL8367C_REG_RLDP_RAND_NUM0    0x18e5
-
-#define    RTL8367C_REG_RLDP_RAND_NUM1    0x18e6
-
-#define    RTL8367C_REG_RLDP_RAND_NUM2    0x18e7
-
-#define    RTL8367C_REG_RLDP_MAGIC_NUM0    0x18e8
-
-#define    RTL8367C_REG_RLDP_MAGIC_NUM1    0x18e9
-
-#define    RTL8367C_REG_RLDP_MAGIC_NUM2    0x18ea
-
-#define    RTL8367C_REG_RLDP_LOOPED_INDICATOR    0x18eb
-#define    RTL8367C_RLDP_LOOPED_INDICATOR_OFFSET    0
-#define    RTL8367C_RLDP_LOOPED_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_RLDP_LOOP_PORT_REG0    0x18ec
-#define    RTL8367C_RLDP_LOOP_PORT_01_OFFSET    8
-#define    RTL8367C_RLDP_LOOP_PORT_01_MASK    0xF00
-#define    RTL8367C_RLDP_LOOP_PORT_00_OFFSET    0
-#define    RTL8367C_RLDP_LOOP_PORT_00_MASK    0xF
-
-#define    RTL8367C_REG_RLDP_LOOP_PORT_REG1    0x18ed
-#define    RTL8367C_RLDP_LOOP_PORT_03_OFFSET    8
-#define    RTL8367C_RLDP_LOOP_PORT_03_MASK    0xF00
-#define    RTL8367C_RLDP_LOOP_PORT_02_OFFSET    0
-#define    RTL8367C_RLDP_LOOP_PORT_02_MASK    0xF
-
-#define    RTL8367C_REG_RLDP_LOOP_PORT_REG2    0x18ee
-#define    RTL8367C_RLDP_LOOP_PORT_05_OFFSET    8
-#define    RTL8367C_RLDP_LOOP_PORT_05_MASK    0xF00
-#define    RTL8367C_RLDP_LOOP_PORT_04_OFFSET    0
-#define    RTL8367C_RLDP_LOOP_PORT_04_MASK    0xF
-
-#define    RTL8367C_REG_RLDP_LOOP_PORT_REG3    0x18ef
-#define    RTL8367C_RLDP_LOOP_PORT_07_OFFSET    8
-#define    RTL8367C_RLDP_LOOP_PORT_07_MASK    0xF00
-#define    RTL8367C_RLDP_LOOP_PORT_06_OFFSET    0
-#define    RTL8367C_RLDP_LOOP_PORT_06_MASK    0xF
-
-#define    RTL8367C_REG_RLDP_RELEASED_INDICATOR    0x18f0
-#define    RTL8367C_RLDP_RELEASED_INDICATOR_OFFSET    0
-#define    RTL8367C_RLDP_RELEASED_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_RLDP_LOOPSTATUS_INDICATOR    0x18f1
-#define    RTL8367C_RLDP_LOOPSTATUS_INDICATOR_OFFSET    0
-#define    RTL8367C_RLDP_LOOPSTATUS_INDICATOR_MASK    0x7FF
-
-#define    RTL8367C_REG_RLDP_LOOP_PORT_REG4    0x18f2
-#define    RTL8367C_RLDP_LOOP_PORT_9_OFFSET    8
-#define    RTL8367C_RLDP_LOOP_PORT_9_MASK    0xF00
-#define    RTL8367C_RLDP_LOOP_PORT_8_OFFSET    0
-#define    RTL8367C_RLDP_LOOP_PORT_8_MASK    0xF
-
-#define    RTL8367C_REG_RLDP_LOOP_PORT_REG5    0x18f3
-#define    RTL8367C_RLDP_LOOP_PORT_REG5_OFFSET    0
-#define    RTL8367C_RLDP_LOOP_PORT_REG5_MASK    0xF
-
-#define    RTL8367C_REG_RLDP_CTRL5    0x18f4
-#define    RTL8367C_RLDP_CTRL5_OFFSET    0
-#define    RTL8367C_RLDP_CTRL5_MASK    0x7
-
-/* (16'h1900)EEE_EEEP_reg */
-
-#define    RTL8367C_REG_EEE_500M_CTRL0    0x1900
-#define    RTL8367C_EEE_500M_CTRL0_OFFSET    0
-#define    RTL8367C_EEE_500M_CTRL0_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_RXIDLE_GIGA_CTRL    0x1901
-#define    RTL8367C_EEE_RXIDLE_GIGA_EN_OFFSET    8
-#define    RTL8367C_EEE_RXIDLE_GIGA_EN_MASK    0x100
-#define    RTL8367C_EEE_RXIDLE_GIGA_OFFSET    0
-#define    RTL8367C_EEE_RXIDLE_GIGA_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_RXIDLE_500M_CTRL    0x1902
-#define    RTL8367C_EEE_RXIDLE_500M_EN_OFFSET    8
-#define    RTL8367C_EEE_RXIDLE_500M_EN_MASK    0x100
-#define    RTL8367C_EEE_RXIDLE_500M_OFFSET    0
-#define    RTL8367C_EEE_RXIDLE_500M_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_DECISION_GIGA_500M    0x1903
-#define    RTL8367C_EEE_DECISION_GIGA_OFFSET    8
-#define    RTL8367C_EEE_DECISION_GIGA_MASK    0xFF00
-#define    RTL8367C_EEE_DECISION_500M_OFFSET    0
-#define    RTL8367C_EEE_DECISION_500M_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_DECISION_100M    0x1904
-#define    RTL8367C_EEE_DECISION_100M_OFFSET    0
-#define    RTL8367C_EEE_DECISION_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_DEFER_TXLPI    0x1905
-#define    RTL8367C_EEEP_DEFER_TXLPI_OFFSET    0
-#define    RTL8367C_EEEP_DEFER_TXLPI_MASK    0x1
-
-#define    RTL8367C_REG_EEEP_EN    0x1906
-#define    RTL8367C_EEEP_SLAVE_EN_OFFSET    3
-#define    RTL8367C_EEEP_SLAVE_EN_MASK    0x8
-#define    RTL8367C_EEEP_100M_OFFSET    2
-#define    RTL8367C_EEEP_100M_MASK    0x4
-#define    RTL8367C_EEEP_500M_OFFSET    1
-#define    RTL8367C_EEEP_500M_MASK    0x2
-#define    RTL8367C_EEEP_GIGA_OFFSET    0
-#define    RTL8367C_EEEP_GIGA_MASK    0x1
-
-#define    RTL8367C_REG_EEEP_TI_GIGA_500M    0x1907
-#define    RTL8367C_EEEP_TI_GIGA_OFFSET    8
-#define    RTL8367C_EEEP_TI_GIGA_MASK    0xFF00
-#define    RTL8367C_EEEP_TI_500M_OFFSET    0
-#define    RTL8367C_EEEP_TI_500M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_TI_100M    0x1908
-#define    RTL8367C_EEEP_TI_100M_OFFSET    0
-#define    RTL8367C_EEEP_TI_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_CTRL2    0x1909
-#define    RTL8367C_EEEP_CTRL2_OFFSET    0
-#define    RTL8367C_EEEP_CTRL2_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_RX_RATE_500M    0x190b
-
-#define    RTL8367C_REG_EEEP_RW_GIGA_SLV    0x190c
-#define    RTL8367C_EEEP_RW_GIGA_SLV_OFFSET    0
-#define    RTL8367C_EEEP_RW_GIGA_SLV_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_TMR_GIGA    0x190d
-#define    RTL8367C_RX_IDLE_EEEP_GIGA_OFFSET    8
-#define    RTL8367C_RX_IDLE_EEEP_GIGA_MASK    0xFF00
-#define    RTL8367C_RX_MIN_SLP_TMR_GIGA_OFFSET    0
-#define    RTL8367C_RX_MIN_SLP_TMR_GIGA_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_TMR_500M    0x190e
-#define    RTL8367C_RX_IDLE_EEEP_500M_OFFSET    8
-#define    RTL8367C_RX_IDLE_EEEP_500M_MASK    0xFF00
-#define    RTL8367C_RX_MIN_SLP_TMR_500M_OFFSET    0
-#define    RTL8367C_RX_MIN_SLP_TMR_500M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_TMR_100M    0x190f
-#define    RTL8367C_RX_IDLE_EEEP_100M_OFFSET    8
-#define    RTL8367C_RX_IDLE_EEEP_100M_MASK    0xFF00
-#define    RTL8367C_RX_MIN_SLP_TMR_100M_OFFSET    0
-#define    RTL8367C_RX_MIN_SLP_TMR_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_RW_500M_MST_SLV    0x1910
-#define    RTL8367C_EEEP_RW_500M_MST_OFFSET    8
-#define    RTL8367C_EEEP_RW_500M_MST_MASK    0xFF00
-#define    RTL8367C_EEEP_RW_500M_SLV_OFFSET    0
-#define    RTL8367C_EEEP_RW_500M_SLV_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_500M_CTRL0    0x1911
-#define    RTL8367C_EEEP_500M_CTRL0_OFFSET    0
-#define    RTL8367C_EEEP_500M_CTRL0_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_500M_CTRL1    0x1912
-#define    RTL8367C_EEEP_TW_500M_OFFSET    8
-#define    RTL8367C_EEEP_TW_500M_MASK    0xFF00
-#define    RTL8367C_EEEP_TP_500M_OFFSET    0
-#define    RTL8367C_EEEP_TP_500M_MASK    0xFF
-
-#define    RTL8367C_REG_EEEP_500M_CTRL2    0x1913
-#define    RTL8367C_EEEP_TXEN_500M_OFFSET    12
-#define    RTL8367C_EEEP_TXEN_500M_MASK    0x1000
-#define    RTL8367C_EEEP_TU_500M_OFFSET    8
-#define    RTL8367C_EEEP_TU_500M_MASK    0x300
-#define    RTL8367C_EEEP_TS_500M_OFFSET    0
-#define    RTL8367C_EEEP_TS_500M_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_NEW_CTRL0    0x1914
-#define    RTL8367C_LINK_UP_DELAY_OFFSET    3
-#define    RTL8367C_LINK_UP_DELAY_MASK    0x18
-#define    RTL8367C_EEE_TXLPI_ORI_OFFSET    2
-#define    RTL8367C_EEE_TXLPI_ORI_MASK    0x4
-#define    RTL8367C_REALTX_SEL_OFFSET    1
-#define    RTL8367C_REALTX_SEL_MASK    0x2
-#define    RTL8367C_EN_FC_EFCT_OFFSET    0
-#define    RTL8367C_EN_FC_EFCT_MASK    0x1
-
-#define    RTL8367C_REG_EEE_LONGIDLE_100M    0x1915
-#define    RTL8367C_EEE_LONGIDLE_100M_OFFSET    0
-#define    RTL8367C_EEE_LONGIDLE_100M_MASK    0x3FF
-
-#define    RTL8367C_REG_EEE_LONGIDLE_500M    0x1916
-#define    RTL8367C_EEE_LONGIDLE_500M_OFFSET    0
-#define    RTL8367C_EEE_LONGIDLE_500M_MASK    0x3FF
-
-#define    RTL8367C_REG_EEE_LONGIDLE_GIGA    0x1917
-#define    RTL8367C_EEE_LONGIDLE_GIGA_OFFSET    0
-#define    RTL8367C_EEE_LONGIDLE_GIGA_MASK    0x3FF
-
-#define    RTL8367C_REG_EEE_MINIPG_100M    0x1918
-
-#define    RTL8367C_REG_EEE_MINIPG_500M    0x1919
-
-#define    RTL8367C_REG_EEE_MINIPG_GIGA    0x191A
-
-#define    RTL8367C_REG_EEE_LONGIDLE_CTRL0    0x191B
-#define    RTL8367C_TX_IDLEN_REQ_100M_OFFSET    10
-#define    RTL8367C_TX_IDLEN_REQ_100M_MASK    0x400
-#define    RTL8367C_TX_IDLEN_REQ_500M_OFFSET    9
-#define    RTL8367C_TX_IDLEN_REQ_500M_MASK    0x200
-#define    RTL8367C_TX_IDLEN_REQ_GIGA_OFFSET    8
-#define    RTL8367C_TX_IDLEN_REQ_GIGA_MASK    0x100
-#define    RTL8367C_EEE_LONGIDLE_CTRL0_TX_LPI_MINIPG_100M_OFFSET    0
-#define    RTL8367C_EEE_LONGIDLE_CTRL0_TX_LPI_MINIPG_100M_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_LONGIDLE_CTRL1    0x191C
-#define    RTL8367C_EEE_LONGIDLE_CTRL1_TX_LPI_MINIPG_GELITE_OFFSET    8
-#define    RTL8367C_EEE_LONGIDLE_CTRL1_TX_LPI_MINIPG_GELITE_MASK    0xFF00
-#define    RTL8367C_EEE_LONGIDLE_CTRL1_TX_LPI_MINIPG_GIGA_OFFSET    0
-#define    RTL8367C_EEE_LONGIDLE_CTRL1_TX_LPI_MINIPG_GIGA_MASK    0xFF
-
-#define    RTL8367C_REG_EEE_TD_CTRL_H    0x191d
-#define    RTL8367C_REF_RXLPI_OFFSET    8
-#define    RTL8367C_REF_RXLPI_MASK    0x100
-#define    RTL8367C_LOW_Q_TX_DELAY_GE_500M_H_OFFSET    4
-#define    RTL8367C_LOW_Q_TX_DELAY_GE_500M_H_MASK    0xF0
-#define    RTL8367C_LOW_Q_TX_DELAY_FE_H_OFFSET    0
-#define    RTL8367C_LOW_Q_TX_DELAY_FE_H_MASK    0xF
-
-/* (16'h1a00)nic_reg */
-
-#define    RTL8367C_REG_NIC_RXRDRL    0x1a04
-#define    RTL8367C_NIC_RXRDRL_OFFSET    0
-#define    RTL8367C_NIC_RXRDRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_RXRDRH    0x1a05
-#define    RTL8367C_NIC_RXRDRH_OFFSET    0
-#define    RTL8367C_NIC_RXRDRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_TXASRL    0x1a08
-#define    RTL8367C_NIC_TXASRL_OFFSET    0
-#define    RTL8367C_NIC_TXASRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_TXASRH    0x1a09
-#define    RTL8367C_NIC_TXASRH_OFFSET    0
-#define    RTL8367C_NIC_TXASRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_RXCMDR    0x1a0c
-#define    RTL8367C_NIC_RXCMDR_OFFSET    0
-#define    RTL8367C_NIC_RXCMDR_MASK    0x1
-
-#define    RTL8367C_REG_NIC_TXCMDR    0x1a0d
-#define    RTL8367C_NIC_TXCMDR_OFFSET    0
-#define    RTL8367C_NIC_TXCMDR_MASK    0x1
-
-#define    RTL8367C_REG_NIC_IMS    0x1a0e
-#define    RTL8367C_NIC_RXIS_OFFSET    7
-#define    RTL8367C_NIC_RXIS_MASK    0x80
-#define    RTL8367C_NIC_TXIS_OFFSET    6
-#define    RTL8367C_NIC_TXIS_MASK    0x40
-#define    RTL8367C_NIC_TXES_OFFSET    5
-#define    RTL8367C_NIC_TXES_MASK    0x20
-#define    RTL8367C_NIC_IMS_DMY_OFFSET    4
-#define    RTL8367C_NIC_IMS_DMY_MASK    0x10
-#define    RTL8367C_NIC_RXBUS_OFFSET    3
-#define    RTL8367C_NIC_RXBUS_MASK    0x8
-#define    RTL8367C_NIC_TXBOS_OFFSET    2
-#define    RTL8367C_NIC_TXBOS_MASK    0x4
-#define    RTL8367C_NIC_RXMIS_OFFSET    1
-#define    RTL8367C_NIC_RXMIS_MASK    0x2
-#define    RTL8367C_NIC_TXNLS_OFFSET    0
-#define    RTL8367C_NIC_TXNLS_MASK    0x1
-
-#define    RTL8367C_REG_NIC_IMR    0x1a0f
-#define    RTL8367C_NIC_RXIE_OFFSET    7
-#define    RTL8367C_NIC_RXIE_MASK    0x80
-#define    RTL8367C_NIC_TXIE_OFFSET    6
-#define    RTL8367C_NIC_TXIE_MASK    0x40
-#define    RTL8367C_NIC_TXEE_OFFSET    5
-#define    RTL8367C_NIC_TXEE_MASK    0x20
-#define    RTL8367C_NIC_IMR_DMY_OFFSET    4
-#define    RTL8367C_NIC_IMR_DMY_MASK    0x10
-#define    RTL8367C_NIC_RXBUE_OFFSET    3
-#define    RTL8367C_NIC_RXBUE_MASK    0x8
-#define    RTL8367C_NIC_TXBOE_OFFSET    2
-#define    RTL8367C_NIC_TXBOE_MASK    0x4
-#define    RTL8367C_NIC_RXMIE_OFFSET    1
-#define    RTL8367C_NIC_RXMIE_MASK    0x2
-#define    RTL8367C_NIC_TXNLE_OFFSET    0
-#define    RTL8367C_NIC_TXNLE_MASK    0x1
-
-#define    RTL8367C_REG_NIC_RXCR0    0x1a14
-#define    RTL8367C_NIC_HFPPE_OFFSET    7
-#define    RTL8367C_NIC_HFPPE_MASK    0x80
-#define    RTL8367C_NIC_HFMPE_OFFSET    6
-#define    RTL8367C_NIC_HFMPE_MASK    0x40
-#define    RTL8367C_NIC_RXBPE_OFFSET    5
-#define    RTL8367C_NIC_RXBPE_MASK    0x20
-#define    RTL8367C_NIC_RXMPE_OFFSET    4
-#define    RTL8367C_NIC_RXMPE_MASK    0x10
-#define    RTL8367C_NIC_RXPPS_OFFSET    2
-#define    RTL8367C_NIC_RXPPS_MASK    0xC
-#define    RTL8367C_NIC_RXAPE_OFFSET    1
-#define    RTL8367C_NIC_RXAPE_MASK    0x2
-#define    RTL8367C_NIC_ARPPE_OFFSET    0
-#define    RTL8367C_NIC_ARPPE_MASK    0x1
-
-#define    RTL8367C_REG_NIC_RXCR1    0x1a15
-#define    RTL8367C_NIC_RL4CEPE_OFFSET    4
-#define    RTL8367C_NIC_RL4CEPE_MASK    0x10
-#define    RTL8367C_NIC_RL3CEPE_OFFSET    3
-#define    RTL8367C_NIC_RL3CEPE_MASK    0x8
-#define    RTL8367C_NIC_RCRCEPE_OFFSET    2
-#define    RTL8367C_NIC_RCRCEPE_MASK    0x4
-#define    RTL8367C_NIC_RMCRC_OFFSET    1
-#define    RTL8367C_NIC_RMCRC_MASK    0x2
-#define    RTL8367C_NIC_RXENABLE_OFFSET    0
-#define    RTL8367C_NIC_RXENABLE_MASK    0x1
-
-#define    RTL8367C_REG_NIC_TXCR    0x1a16
-#define    RTL8367C_NIC_LBE_OFFSET    2
-#define    RTL8367C_NIC_LBE_MASK    0x4
-#define    RTL8367C_NIC_TXMFM_OFFSET    1
-#define    RTL8367C_NIC_TXMFM_MASK    0x2
-#define    RTL8367C_NIC_TXENABLE_OFFSET    0
-#define    RTL8367C_NIC_TXENABLE_MASK    0x1
-
-#define    RTL8367C_REG_NIC_GCR    0x1a17
-#define    RTL8367C_DUMMY_7_6_OFFSET    6
-#define    RTL8367C_DUMMY_7_6_MASK    0xC0
-#define    RTL8367C_NIC_RXMTU_OFFSET    4
-#define    RTL8367C_NIC_RXMTU_MASK    0x30
-#define    RTL8367C_NIC_GCR_DUMMY_0_OFFSET    0
-#define    RTL8367C_NIC_GCR_DUMMY_0_MASK    0x1
-
-#define    RTL8367C_REG_NIC_MHR0    0x1a24
-#define    RTL8367C_NIC_MHR0_OFFSET    0
-#define    RTL8367C_NIC_MHR0_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_MHR1    0x1a25
-#define    RTL8367C_NIC_MHR1_OFFSET    0
-#define    RTL8367C_NIC_MHR1_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_MHR2    0x1a26
-#define    RTL8367C_NIC_MHR2_OFFSET    0
-#define    RTL8367C_NIC_MHR2_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_MHR3    0x1a27
-#define    RTL8367C_NIC_MHR3_OFFSET    0
-#define    RTL8367C_NIC_MHR3_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_MHR4    0x1a28
-#define    RTL8367C_NIC_MHR4_OFFSET    0
-#define    RTL8367C_NIC_MHR4_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_MHR5    0x1a29
-#define    RTL8367C_NIC_MHR5_OFFSET    0
-#define    RTL8367C_NIC_MHR5_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_MHR6    0x1a2a
-#define    RTL8367C_NIC_MHR6_OFFSET    0
-#define    RTL8367C_NIC_MHR6_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_MHR7    0x1a2b
-#define    RTL8367C_NIC_MHR7_OFFSET    0
-#define    RTL8367C_NIC_MHR7_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR0    0x1a2c
-#define    RTL8367C_NIC_PAHR0_OFFSET    0
-#define    RTL8367C_NIC_PAHR0_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR1    0x1a2d
-#define    RTL8367C_NIC_PAHR1_OFFSET    0
-#define    RTL8367C_NIC_PAHR1_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR2    0x1a2e
-#define    RTL8367C_NIC_PAHR2_OFFSET    0
-#define    RTL8367C_NIC_PAHR2_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR3    0x1a2f
-#define    RTL8367C_NIC_PAHR3_OFFSET    0
-#define    RTL8367C_NIC_PAHR3_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR4    0x1a30
-#define    RTL8367C_NIC_PAHR4_OFFSET    0
-#define    RTL8367C_NIC_PAHR4_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR5    0x1a31
-#define    RTL8367C_NIC_PAHR5_OFFSET    0
-#define    RTL8367C_NIC_PAHR5_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR6    0x1a32
-#define    RTL8367C_NIC_PAHR6_OFFSET    0
-#define    RTL8367C_NIC_PAHR6_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_PAHR7    0x1a33
-#define    RTL8367C_NIC_PAHR7_OFFSET    0
-#define    RTL8367C_NIC_PAHR7_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_TXSTOPRL    0x1a44
-#define    RTL8367C_NIC_TXSTOPRL_OFFSET    0
-#define    RTL8367C_NIC_TXSTOPRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_TXSTOPRH    0x1a45
-#define    RTL8367C_NIC_TXSTOPRH_OFFSET    0
-#define    RTL8367C_NIC_TXSTOPRH_MASK    0x3
-
-#define    RTL8367C_REG_NIC_RXSTOPRL    0x1a46
-#define    RTL8367C_NIC_RXSTOPRL_OFFSET    0
-#define    RTL8367C_NIC_RXSTOPRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_RXSTOPRH    0x1a47
-#define    RTL8367C_NIC_RXSTOPRH_OFFSET    0
-#define    RTL8367C_NIC_RXSTOPRH_MASK    0x3
-
-#define    RTL8367C_REG_NIC_RXFSTR    0x1a48
-#define    RTL8367C_NIC_RXFSTR_OFFSET    0
-#define    RTL8367C_NIC_RXFSTR_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_RXMBTRL    0x1a4c
-#define    RTL8367C_NIC_RXMBTRL_OFFSET    0
-#define    RTL8367C_NIC_RXMBTRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_RXMBTRH    0x1a4d
-#define    RTL8367C_NIC_RXMBTRH_OFFSET    0
-#define    RTL8367C_NIC_RXMBTRH_MASK    0x7F
-
-#define    RTL8367C_REG_NIC_RXMPTR    0x1a4e
-#define    RTL8367C_NIC_RXMPTR_OFFSET    0
-#define    RTL8367C_NIC_RXMPTR_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_T0TR    0x1a4f
-#define    RTL8367C_NIC_T0TR_OFFSET    0
-#define    RTL8367C_NIC_T0TR_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_CRXCPRL    0x1a50
-#define    RTL8367C_NIC_CRXCPRL_OFFSET    0
-#define    RTL8367C_NIC_CRXCPRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_CRXCPRH    0x1a51
-#define    RTL8367C_NIC_CRXCPRH_OFFSET    0
-#define    RTL8367C_NIC_CRXCPRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_CTXCPRL    0x1a52
-#define    RTL8367C_NIC_CTXCPRL_OFFSET    0
-#define    RTL8367C_NIC_CTXCPRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_CTXPCRH    0x1a53
-#define    RTL8367C_NIC_CTXPCRH_OFFSET    0
-#define    RTL8367C_NIC_CTXPCRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_SRXCURPKTRL    0x1a54
-#define    RTL8367C_NIC_SRXCURPKTRL_OFFSET    0
-#define    RTL8367C_NIC_SRXCURPKTRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_SRXCURPKTRH    0x1a55
-#define    RTL8367C_NIC_SRXCURPKTRH_OFFSET    0
-#define    RTL8367C_NIC_SRXCURPKTRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_STXCURPKTRL    0x1a56
-#define    RTL8367C_NIC_STXCURPKTRL_OFFSET    0
-#define    RTL8367C_NIC_STXCURPKTRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_STXCURPKTRH    0x1a57
-#define    RTL8367C_NIC_STXCURPKTRH_OFFSET    0
-#define    RTL8367C_NIC_STXCURPKTRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_STXPKTLENRL    0x1a58
-#define    RTL8367C_NIC_STXPKTLENRL_OFFSET    0
-#define    RTL8367C_NIC_STXPKTLENRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_STXPKTLENRH    0x1a59
-#define    RTL8367C_NIC_STXPKTLENRH_OFFSET    0
-#define    RTL8367C_NIC_STXPKTLENRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_STXCURUNITRL    0x1a5a
-#define    RTL8367C_NIC_STXCURUNITRL_OFFSET    0
-#define    RTL8367C_NIC_STXCURUNITRL_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_STXCURUNITRH    0x1a5b
-#define    RTL8367C_NIC_STXCURUNITRH_OFFSET    0
-#define    RTL8367C_NIC_STXCURUNITRH_MASK    0xFF
-
-#define    RTL8367C_REG_NIC_DROP_MODE    0x1a5c
-#define    RTL8367C_NIC_RXDV_MODE_OFFSET    1
-#define    RTL8367C_NIC_RXDV_MODE_MASK    0x2
-#define    RTL8367C_NIC_DROP_MODE_OFFSET    0
-#define    RTL8367C_NIC_DROP_MODE_MASK    0x1
-
-/* (16'h1b00)LED */
-
-#define    RTL8367C_REG_LED_SYS_CONFIG    0x1b00
-#define    RTL8367C_LED_SYS_CONFIG_DUMMY_15_OFFSET    15
-#define    RTL8367C_LED_SYS_CONFIG_DUMMY_15_MASK    0x8000
-#define    RTL8367C_LED_SERIAL_OUT_MODE_OFFSET    14
-#define    RTL8367C_LED_SERIAL_OUT_MODE_MASK    0x4000
-#define    RTL8367C_LED_EEE_LPI_MODE_OFFSET    13
-#define    RTL8367C_LED_EEE_LPI_MODE_MASK    0x2000
-#define    RTL8367C_LED_EEE_LPI_EN_OFFSET    12
-#define    RTL8367C_LED_EEE_LPI_EN_MASK    0x1000
-#define    RTL8367C_LED_EEE_LPI_10_OFFSET    11
-#define    RTL8367C_LED_EEE_LPI_10_MASK    0x800
-#define    RTL8367C_LED_EEE_CAP_10_OFFSET    10
-#define    RTL8367C_LED_EEE_CAP_10_MASK    0x400
-#define    RTL8367C_LED_LPI_SEL_OFFSET    8
-#define    RTL8367C_LED_LPI_SEL_MASK    0x300
-#define    RTL8367C_SERI_LED_ACT_LOW_OFFSET    7
-#define    RTL8367C_SERI_LED_ACT_LOW_MASK    0x80
-#define    RTL8367C_LED_POWERON_2_OFFSET    6
-#define    RTL8367C_LED_POWERON_2_MASK    0x40
-#define    RTL8367C_LED_POWERON_1_OFFSET    5
-#define    RTL8367C_LED_POWERON_1_MASK    0x20
-#define    RTL8367C_LED_POWERON_0_OFFSET    4
-#define    RTL8367C_LED_POWERON_0_MASK    0x10
-#define    RTL8367C_LED_IO_DISABLE_OFFSET    3
-#define    RTL8367C_LED_IO_DISABLE_MASK    0x8
-#define    RTL8367C_DUMMY_2_2_OFFSET    2
-#define    RTL8367C_DUMMY_2_2_MASK    0x4
-#define    RTL8367C_LED_SELECT_OFFSET    0
-#define    RTL8367C_LED_SELECT_MASK    0x3
-
-#define    RTL8367C_REG_LED_SYS_CONFIG2    0x1b01
-#define    RTL8367C_LED_SYS_CONFIG2_DUMMY_OFFSET    2
-#define    RTL8367C_LED_SYS_CONFIG2_DUMMY_MASK    0xFFFC
-#define    RTL8367C_GATE_LPTD_BYPASS_OFFSET    1
-#define    RTL8367C_GATE_LPTD_BYPASS_MASK    0x2
-#define    RTL8367C_LED_SPD_MODE_OFFSET    0
-#define    RTL8367C_LED_SPD_MODE_MASK    0x1
-
-#define    RTL8367C_REG_LED_MODE    0x1b02
-#define    RTL8367C_DLINK_TIME_OFFSET    15
-#define    RTL8367C_DLINK_TIME_MASK    0x8000
-#define    RTL8367C_LED_BUZZ_DUTY_OFFSET    14
-#define    RTL8367C_LED_BUZZ_DUTY_MASK    0x4000
-#define    RTL8367C_BUZZER_RATE_OFFSET    12
-#define    RTL8367C_BUZZER_RATE_MASK    0x3000
-#define    RTL8367C_LOOP_DETECT_MODE_OFFSET    11
-#define    RTL8367C_LOOP_DETECT_MODE_MASK    0x800
-#define    RTL8367C_SEL_PWRON_TIME_OFFSET    9
-#define    RTL8367C_SEL_PWRON_TIME_MASK    0x600
-#define    RTL8367C_EN_DLINK_LED_OFFSET    8
-#define    RTL8367C_EN_DLINK_LED_MASK    0x100
-#define    RTL8367C_LOOP_DETECT_RATE_OFFSET    6
-#define    RTL8367C_LOOP_DETECT_RATE_MASK    0xC0
-#define    RTL8367C_FORCE_RATE_OFFSET    4
-#define    RTL8367C_FORCE_RATE_MASK    0x30
-#define    RTL8367C_SEL_LEDRATE_OFFSET    1
-#define    RTL8367C_SEL_LEDRATE_MASK    0xE
-#define    RTL8367C_SPEED_UP_OFFSET    0
-#define    RTL8367C_SPEED_UP_MASK    0x1
-
-#define    RTL8367C_REG_LED_CONFIGURATION    0x1b03
-#define    RTL8367C_LED_CONFIGURATION_DUMMY_OFFSET    15
-#define    RTL8367C_LED_CONFIGURATION_DUMMY_MASK    0x8000
-#define    RTL8367C_LED_CONFIG_SEL_OFFSET    14
-#define    RTL8367C_LED_CONFIG_SEL_MASK    0x4000
-#define    RTL8367C_DATA_LED_OFFSET    12
-#define    RTL8367C_DATA_LED_MASK    0x3000
-#define    RTL8367C_LED2_CFG_OFFSET    8
-#define    RTL8367C_LED2_CFG_MASK    0xF00
-#define    RTL8367C_LED1_CFG_OFFSET    4
-#define    RTL8367C_LED1_CFG_MASK    0xF0
-#define    RTL8367C_LED0_CFG_OFFSET    0
-#define    RTL8367C_LED0_CFG_MASK    0xF
-
-#define    RTL8367C_REG_RTCT_RESULTS_CFG    0x1b04
-#define    RTL8367C_RTCT_2PAIR_FTT_OFFSET    15
-#define    RTL8367C_RTCT_2PAIR_FTT_MASK    0x8000
-#define    RTL8367C_RTCT_2PAIR_MODE_OFFSET    14
-#define    RTL8367C_RTCT_2PAIR_MODE_MASK    0x4000
-#define    RTL8367C_BLINK_EN_OFFSET    13
-#define    RTL8367C_BLINK_EN_MASK    0x2000
-#define    RTL8367C_TIMEOUT_OFFSET    12
-#define    RTL8367C_TIMEOUT_MASK    0x1000
-#define    RTL8367C_EN_CD_SAME_SHORT_OFFSET    11
-#define    RTL8367C_EN_CD_SAME_SHORT_MASK    0x800
-#define    RTL8367C_EN_CD_SAME_OPEN_OFFSET    10
-#define    RTL8367C_EN_CD_SAME_OPEN_MASK    0x400
-#define    RTL8367C_EN_CD_SAME_LINEDRIVER_OFFSET    9
-#define    RTL8367C_EN_CD_SAME_LINEDRIVER_MASK    0x200
-#define    RTL8367C_EN_CD_SAME_MISMATCH_OFFSET    8
-#define    RTL8367C_EN_CD_SAME_MISMATCH_MASK    0x100
-#define    RTL8367C_EN_CD_SHORT_OFFSET    7
-#define    RTL8367C_EN_CD_SHORT_MASK    0x80
-#define    RTL8367C_EN_AB_SHORT_OFFSET    6
-#define    RTL8367C_EN_AB_SHORT_MASK    0x40
-#define    RTL8367C_EN_CD_OPEN_OFFSET    5
-#define    RTL8367C_EN_CD_OPEN_MASK    0x20
-#define    RTL8367C_EN_AB_OPEN_OFFSET    4
-#define    RTL8367C_EN_AB_OPEN_MASK    0x10
-#define    RTL8367C_EN_CD_MISMATCH_OFFSET    3
-#define    RTL8367C_EN_CD_MISMATCH_MASK    0x8
-#define    RTL8367C_EN_AB_MISMATCH_OFFSET    2
-#define    RTL8367C_EN_AB_MISMATCH_MASK    0x4
-#define    RTL8367C_EN_CD_LINEDRIVER_OFFSET    1
-#define    RTL8367C_EN_CD_LINEDRIVER_MASK    0x2
-#define    RTL8367C_EN_AB_LINEDRIVER_OFFSET    0
-#define    RTL8367C_EN_AB_LINEDRIVER_MASK    0x1
-
-#define    RTL8367C_REG_RTCT_LED    0x1b05
-#define    RTL8367C_DUMMY_1b05a_OFFSET    12
-#define    RTL8367C_DUMMY_1b05a_MASK    0xF000
-#define    RTL8367C_RTCT_LED2_OFFSET    8
-#define    RTL8367C_RTCT_LED2_MASK    0xF00
-#define    RTL8367C_RTCT_LED1_OFFSET    4
-#define    RTL8367C_RTCT_LED1_MASK    0xF0
-#define    RTL8367C_RTCT_LED0_OFFSET    0
-#define    RTL8367C_RTCT_LED0_MASK    0xF
-
-#define    RTL8367C_REG_CPU_FORCE_LED_CFG    0x1b07
-#define    RTL8367C_DUMMY_1b07a_OFFSET    8
-#define    RTL8367C_DUMMY_1b07a_MASK    0xFF00
-#define    RTL8367C_LED_FORCE_MODE_OFFSET    2
-#define    RTL8367C_LED_FORCE_MODE_MASK    0xFC
-#define    RTL8367C_FORCE_MODE_OFFSET    0
-#define    RTL8367C_FORCE_MODE_MASK    0x3
-
-#define    RTL8367C_REG_CPU_FORCE_LED0_CFG0    0x1b08
-#define    RTL8367C_PORT7_LED0_MODE_OFFSET    14
-#define    RTL8367C_PORT7_LED0_MODE_MASK    0xC000
-#define    RTL8367C_PORT6_LED0_MODE_OFFSET    12
-#define    RTL8367C_PORT6_LED0_MODE_MASK    0x3000
-#define    RTL8367C_PORT5_LED0_MODE_OFFSET    10
-#define    RTL8367C_PORT5_LED0_MODE_MASK    0xC00
-#define    RTL8367C_PORT4_LED0_MODE_OFFSET    8
-#define    RTL8367C_PORT4_LED0_MODE_MASK    0x300
-#define    RTL8367C_PORT3_LED0_MODE_OFFSET    6
-#define    RTL8367C_PORT3_LED0_MODE_MASK    0xC0
-#define    RTL8367C_PORT2_LED0_MODE_OFFSET    4
-#define    RTL8367C_PORT2_LED0_MODE_MASK    0x30
-#define    RTL8367C_PORT1_LED0_MODE_OFFSET    2
-#define    RTL8367C_PORT1_LED0_MODE_MASK    0xC
-#define    RTL8367C_PORT0_LED0_MODE_OFFSET    0
-#define    RTL8367C_PORT0_LED0_MODE_MASK    0x3
-
-#define    RTL8367C_REG_CPU_FORCE_LED0_CFG1    0x1b09
-#define    RTL8367C_DUMMY_1b09a_OFFSET    4
-#define    RTL8367C_DUMMY_1b09a_MASK    0xFFF0
-#define    RTL8367C_PORT9_LED0_MODE_OFFSET    2
-#define    RTL8367C_PORT9_LED0_MODE_MASK    0xC
-#define    RTL8367C_PORT8_LED0_MODE_OFFSET    0
-#define    RTL8367C_PORT8_LED0_MODE_MASK    0x3
-
-#define    RTL8367C_REG_CPU_FORCE_LED1_CFG0    0x1b0a
-#define    RTL8367C_PORT7_LED1_MODE_OFFSET    14
-#define    RTL8367C_PORT7_LED1_MODE_MASK    0xC000
-#define    RTL8367C_PORT6_LED1_MODE_OFFSET    12
-#define    RTL8367C_PORT6_LED1_MODE_MASK    0x3000
-#define    RTL8367C_PORT5_LED1_MODE_OFFSET    10
-#define    RTL8367C_PORT5_LED1_MODE_MASK    0xC00
-#define    RTL8367C_PORT4_LED1_MODE_OFFSET    8
-#define    RTL8367C_PORT4_LED1_MODE_MASK    0x300
-#define    RTL8367C_PORT3_LED1_MODE_OFFSET    6
-#define    RTL8367C_PORT3_LED1_MODE_MASK    0xC0
-#define    RTL8367C_PORT2_LED1_MODE_OFFSET    4
-#define    RTL8367C_PORT2_LED1_MODE_MASK    0x30
-#define    RTL8367C_PORT1_LED1_MODE_OFFSET    2
-#define    RTL8367C_PORT1_LED1_MODE_MASK    0xC
-#define    RTL8367C_PORT0_LED1_MODE_OFFSET    0
-#define    RTL8367C_PORT0_LED1_MODE_MASK    0x3
-
-#define    RTL8367C_REG_CPU_FORCE_LED1_CFG1    0x1b0b
-#define    RTL8367C_DUMMY_1b0ba_OFFSET    4
-#define    RTL8367C_DUMMY_1b0ba_MASK    0xFFF0
-#define    RTL8367C_PORT9_LED1_MODE_OFFSET    2
-#define    RTL8367C_PORT9_LED1_MODE_MASK    0xC
-#define    RTL8367C_PORT8_LED1_MODE_OFFSET    0
-#define    RTL8367C_PORT8_LED1_MODE_MASK    0x3
-
-#define    RTL8367C_REG_CPU_FORCE_LED2_CFG0    0x1b0c
-#define    RTL8367C_PORT7_LED2_MODE_OFFSET    14
-#define    RTL8367C_PORT7_LED2_MODE_MASK    0xC000
-#define    RTL8367C_PORT6_LED2_MODE_OFFSET    12
-#define    RTL8367C_PORT6_LED2_MODE_MASK    0x3000
-#define    RTL8367C_PORT5_LED2_MODE_OFFSET    10
-#define    RTL8367C_PORT5_LED2_MODE_MASK    0xC00
-#define    RTL8367C_PORT4_LED2_MODE_OFFSET    8
-#define    RTL8367C_PORT4_LED2_MODE_MASK    0x300
-#define    RTL8367C_PORT3_LED2_MODE_OFFSET    6
-#define    RTL8367C_PORT3_LED2_MODE_MASK    0xC0
-#define    RTL8367C_PORT2_LED2_MODE_OFFSET    4
-#define    RTL8367C_PORT2_LED2_MODE_MASK    0x30
-#define    RTL8367C_PORT1_LED2_MODE_OFFSET    2
-#define    RTL8367C_PORT1_LED2_MODE_MASK    0xC
-#define    RTL8367C_PORT0_LED2_MODE_OFFSET    0
-#define    RTL8367C_PORT0_LED2_MODE_MASK    0x3
-
-#define    RTL8367C_REG_CPU_FORCE_LED2_CFG1    0x1b0d
-#define    RTL8367C_DUMMY_1b0da_OFFSET    4
-#define    RTL8367C_DUMMY_1b0da_MASK    0xFFF0
-#define    RTL8367C_PORT9_LED2_MODE_OFFSET    2
-#define    RTL8367C_PORT9_LED2_MODE_MASK    0xC
-#define    RTL8367C_PORT8_LED2_MODE_OFFSET    0
-#define    RTL8367C_PORT8_LED2_MODE_MASK    0x3
-
-#define    RTL8367C_REG_LED_ACTIVE_LOW_CFG0    0x1b0e
-#define    RTL8367C_LED_ACTIVE_LOW_CFG0_DUMMY_15_OFFSET    15
-#define    RTL8367C_LED_ACTIVE_LOW_CFG0_DUMMY_15_MASK    0x8000
-#define    RTL8367C_PORT3_LED_ACTIVE_LOW_OFFSET    12
-#define    RTL8367C_PORT3_LED_ACTIVE_LOW_MASK    0x7000
-#define    RTL8367C_LED_ACTIVE_LOW_CFG0_DUMMY_11_OFFSET    11
-#define    RTL8367C_LED_ACTIVE_LOW_CFG0_DUMMY_11_MASK    0x800
-#define    RTL8367C_PORT2_LED_ACTIVE_LOW_OFFSET    8
-#define    RTL8367C_PORT2_LED_ACTIVE_LOW_MASK    0x700
-#define    RTL8367C_DUMMY_7_OFFSET    7
-#define    RTL8367C_DUMMY_7_MASK    0x80
-#define    RTL8367C_PORT1_LED_ACTIVE_LOW_OFFSET    4
-#define    RTL8367C_PORT1_LED_ACTIVE_LOW_MASK    0x70
-#define    RTL8367C_DUMMY_3_OFFSET    3
-#define    RTL8367C_DUMMY_3_MASK    0x8
-#define    RTL8367C_PORT0_LED_ACTIVE_LOW_OFFSET    0
-#define    RTL8367C_PORT0_LED_ACTIVE_LOW_MASK    0x7
-
-#define    RTL8367C_REG_LED_ACTIVE_LOW_CFG1    0x1b0f
-#define    RTL8367C_LED_ACTIVE_LOW_CFG1_DUMMY_15_OFFSET    15
-#define    RTL8367C_LED_ACTIVE_LOW_CFG1_DUMMY_15_MASK    0x8000
-#define    RTL8367C_PORT7_LED_ACTIVE_LOW_OFFSET    12
-#define    RTL8367C_PORT7_LED_ACTIVE_LOW_MASK    0x7000
-#define    RTL8367C_LED_ACTIVE_LOW_CFG1_DUMMY_11_OFFSET    11
-#define    RTL8367C_LED_ACTIVE_LOW_CFG1_DUMMY_11_MASK    0x800
-#define    RTL8367C_PORT6_LED_ACTIVE_LOW_OFFSET    8
-#define    RTL8367C_PORT6_LED_ACTIVE_LOW_MASK    0x700
-#define    RTL8367C_DUMMY_1b0f_b_OFFSET    7
-#define    RTL8367C_DUMMY_1b0f_b_MASK    0x80
-#define    RTL8367C_PORT5_LED_ACTIVE_LOW_OFFSET    4
-#define    RTL8367C_PORT5_LED_ACTIVE_LOW_MASK    0x70
-#define    RTL8367C_DUMMY_1b0f_a_OFFSET    3
-#define    RTL8367C_DUMMY_1b0f_a_MASK    0x8
-#define    RTL8367C_PORT4_LED_ACTIVE_LOW_OFFSET    0
-#define    RTL8367C_PORT4_LED_ACTIVE_LOW_MASK    0x7
-
-#define    RTL8367C_REG_LED_ACTIVE_LOW_CFG2    0x1b10
-#define    RTL8367C_DUMMY_1b10_b_OFFSET    7
-#define    RTL8367C_DUMMY_1b10_b_MASK    0xFF80
-#define    RTL8367C_PORT9_LED_ACTIVE_LOW_OFFSET    4
-#define    RTL8367C_PORT9_LED_ACTIVE_LOW_MASK    0x70
-#define    RTL8367C_DUMMY_1b10_a_OFFSET    3
-#define    RTL8367C_DUMMY_1b10_a_MASK    0x8
-#define    RTL8367C_PORT8_LED_ACTIVE_LOW_OFFSET    0
-#define    RTL8367C_PORT8_LED_ACTIVE_LOW_MASK    0x7
-
-#define    RTL8367C_REG_SEL_RTCT_PARA    0x1b21
-#define    RTL8367C_DO_RTCT_COMMAND_OFFSET    15
-#define    RTL8367C_DO_RTCT_COMMAND_MASK    0x8000
-#define    RTL8367C_SEL_RTCT_PARA_DUMMY_OFFSET    12
-#define    RTL8367C_SEL_RTCT_PARA_DUMMY_MASK    0x7000
-#define    RTL8367C_SEL_RTCT_RLSTLED_TIME_OFFSET    10
-#define    RTL8367C_SEL_RTCT_RLSTLED_TIME_MASK    0xC00
-#define    RTL8367C_SEL_RTCT_TEST_LED_TIME_OFFSET    8
-#define    RTL8367C_SEL_RTCT_TEST_LED_TIME_MASK    0x300
-#define    RTL8367C_EN_SCAN_RTCT_OFFSET    7
-#define    RTL8367C_EN_SCAN_RTCT_MASK    0x80
-#define    RTL8367C_EN_RTCT_TIMOUT_OFFSET    6
-#define    RTL8367C_EN_RTCT_TIMOUT_MASK    0x40
-#define    RTL8367C_EN_ALL_RTCT_OFFSET    5
-#define    RTL8367C_EN_ALL_RTCT_MASK    0x20
-#define    RTL8367C_SEL_RTCT_PLE_WID_OFFSET    0
-#define    RTL8367C_SEL_RTCT_PLE_WID_MASK    0x1F
-
-#define    RTL8367C_REG_RTCT_ENABLE    0x1b22
-#define    RTL8367C_RTCT_ENABLE_DUMMY_OFFSET    8
-#define    RTL8367C_RTCT_ENABLE_DUMMY_MASK    0xFF00
-#define    RTL8367C_RTCT_ENABLE_PORT_MASK_OFFSET    0
-#define    RTL8367C_RTCT_ENABLE_PORT_MASK_MASK    0xFF
-
-#define    RTL8367C_REG_RTCT_TIMEOUT    0x1b23
-
-#define    RTL8367C_REG_PARA_LED_IO_EN1    0x1b24
-#define    RTL8367C_LED1_PARA_P07_00_OFFSET    8
-#define    RTL8367C_LED1_PARA_P07_00_MASK    0xFF00
-#define    RTL8367C_LED0_PARA_P07_00_OFFSET    0
-#define    RTL8367C_LED0_PARA_P07_00_MASK    0xFF
-
-#define    RTL8367C_REG_PARA_LED_IO_EN2    0x1b25
-#define    RTL8367C_DUMMY_15_8_OFFSET    8
-#define    RTL8367C_DUMMY_15_8_MASK    0xFF00
-#define    RTL8367C_LED2_PARA_P07_00_OFFSET    0
-#define    RTL8367C_LED2_PARA_P07_00_MASK    0xFF
-
-#define    RTL8367C_REG_SCAN0_LED_IO_EN1    0x1b26
-#define    RTL8367C_SCAN0_LED_IO_EN1_DUMMY_OFFSET    3
-#define    RTL8367C_SCAN0_LED_IO_EN1_DUMMY_MASK    0xFFF8
-#define    RTL8367C_LED_LOOP_DET_BUZZER_EN_OFFSET    2
-#define    RTL8367C_LED_LOOP_DET_BUZZER_EN_MASK    0x4
-#define    RTL8367C_LED_SERI_DATA_EN_OFFSET    1
-#define    RTL8367C_LED_SERI_DATA_EN_MASK    0x2
-#define    RTL8367C_LED_SERI_CLK_EN_OFFSET    0
-#define    RTL8367C_LED_SERI_CLK_EN_MASK    0x1
-
-#define    RTL8367C_REG_SCAN1_LED_IO_EN2    0x1b27
-#define    RTL8367C_LED_SCAN1_BI_PORT_EN_OFFSET    8
-#define    RTL8367C_LED_SCAN1_BI_PORT_EN_MASK    0xFF00
-#define    RTL8367C_LED_SCAN1_BI_STA_EN_OFFSET    7
-#define    RTL8367C_LED_SCAN1_BI_STA_EN_MASK    0x80
-#define    RTL8367C_SCAN1_LED_IO_EN2_DUMMY_0_OFFSET    6
-#define    RTL8367C_SCAN1_LED_IO_EN2_DUMMY_0_MASK    0x40
-#define    RTL8367C_LED_SCAN1_SI_PORT_EN_OFFSET    2
-#define    RTL8367C_LED_SCAN1_SI_PORT_EN_MASK    0x3C
-#define    RTL8367C_LED_SCAN1_SI_STA_EN_OFFSET    0
-#define    RTL8367C_LED_SCAN1_SI_STA_EN_MASK    0x3
-
-#define    RTL8367C_REG_LPI_LED_OPT1    0x1b28
-#define    RTL8367C_LPI_TAG4_OFFSET    12
-#define    RTL8367C_LPI_TAG4_MASK    0xF000
-#define    RTL8367C_LPI_TAG3_OFFSET    8
-#define    RTL8367C_LPI_TAG3_MASK    0xF00
-#define    RTL8367C_LPI_TAG2_OFFSET    4
-#define    RTL8367C_LPI_TAG2_MASK    0xF0
-#define    RTL8367C_LPI_TAG1_OFFSET    0
-#define    RTL8367C_LPI_TAG1_MASK    0xF
-
-#define    RTL8367C_REG_LPI_LED_OPT2    0x1b29
-#define    RTL8367C_LPI_LED_OPT2_DUMMY_OFFSET    15
-#define    RTL8367C_LPI_LED_OPT2_DUMMY_MASK    0x8000
-#define    RTL8367C_LPI_LED2_WEAK_OFFSET    14
-#define    RTL8367C_LPI_LED2_WEAK_MASK    0x4000
-#define    RTL8367C_LPI_LED1_WEAK_OFFSET    13
-#define    RTL8367C_LPI_LED1_WEAK_MASK    0x2000
-#define    RTL8367C_LPI_LED0_WEAK_OFFSET    12
-#define    RTL8367C_LPI_LED0_WEAK_MASK    0x1000
-#define    RTL8367C_LPI_LED2_OFFSET    11
-#define    RTL8367C_LPI_LED2_MASK    0x800
-#define    RTL8367C_LPI_LED1_OFFSET    10
-#define    RTL8367C_LPI_LED1_MASK    0x400
-#define    RTL8367C_LPI_LED0_OFFSET    9
-#define    RTL8367C_LPI_LED0_MASK    0x200
-#define    RTL8367C_LPI_TAG8_OFFSET    8
-#define    RTL8367C_LPI_TAG8_MASK    0x100
-#define    RTL8367C_LPI_TAG7_OFFSET    6
-#define    RTL8367C_LPI_TAG7_MASK    0xC0
-#define    RTL8367C_LPI_TAG6_OFFSET    4
-#define    RTL8367C_LPI_TAG6_MASK    0x30
-#define    RTL8367C_LPI_TAG5_OFFSET    0
-#define    RTL8367C_LPI_TAG5_MASK    0xF
-
-#define    RTL8367C_REG_LPI_LED_OPT3    0x1b2a
-#define    RTL8367C_LPI_LED_OPT3_DUMMY_OFFSET    3
-#define    RTL8367C_LPI_LED_OPT3_DUMMY_MASK    0xFFF8
-#define    RTL8367C_RESTORE_LED_RATE_SEL_OFFSET    1
-#define    RTL8367C_RESTORE_LED_RATE_SEL_MASK    0x6
-#define    RTL8367C_RESTORE_LED_SEL_OFFSET    0
-#define    RTL8367C_RESTORE_LED_SEL_MASK    0x1
-
-#define    RTL8367C_REG_P0_LED_MUX    0x1b2b
-#define    RTL8367C_CFG_P0_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P0_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P0_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P0_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P0_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P0_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P1_LED_MUX    0x1b2c
-#define    RTL8367C_CFG_P1_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P1_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P1_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P1_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P1_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P1_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P2_LED_MUX    0x1b2d
-#define    RTL8367C_CFG_P2_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P2_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P2_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P2_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P2_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P2_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P3_LED_MUX    0x1b2e
-#define    RTL8367C_CFG_P3_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P3_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P3_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P3_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P3_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P3_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P4_LED_MUX    0x1b2f
-#define    RTL8367C_CFG_P4_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P4_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P4_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P4_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P4_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P4_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_LED0_DATA_CTRL    0x1b30
-#define    RTL8367C_CFG_DATA_LED0_SEL_OFFSET    6
-#define    RTL8367C_CFG_DATA_LED0_SEL_MASK    0x40
-#define    RTL8367C_CFG_DATA_LED0_ACT_OFFSET    4
-#define    RTL8367C_CFG_DATA_LED0_ACT_MASK    0x30
-#define    RTL8367C_CFG_DATA_LED0_SPD_OFFSET    0
-#define    RTL8367C_CFG_DATA_LED0_SPD_MASK    0xF
-
-#define    RTL8367C_REG_LED1_DATA_CTRL    0x1b31
-#define    RTL8367C_CFG_DATA_LED1_SEL_OFFSET    6
-#define    RTL8367C_CFG_DATA_LED1_SEL_MASK    0x40
-#define    RTL8367C_CFG_DATA_LED1_ACT_OFFSET    4
-#define    RTL8367C_CFG_DATA_LED1_ACT_MASK    0x30
-#define    RTL8367C_CFG_DATA_LED1_SPD_OFFSET    0
-#define    RTL8367C_CFG_DATA_LED1_SPD_MASK    0xF
-
-#define    RTL8367C_REG_LED2_DATA_CTRL    0x1b32
-#define    RTL8367C_CFG_DATA_LED2_SEL_OFFSET    6
-#define    RTL8367C_CFG_DATA_LED2_SEL_MASK    0x40
-#define    RTL8367C_CFG_DATA_LED2_ACT_OFFSET    4
-#define    RTL8367C_CFG_DATA_LED2_ACT_MASK    0x30
-#define    RTL8367C_CFG_DATA_LED2_SPD_OFFSET    0
-#define    RTL8367C_CFG_DATA_LED2_SPD_MASK    0xF
-
-#define    RTL8367C_REG_PARA_LED_IO_EN3    0x1b33
-#define    RTL8367C_dummy_1b33a_OFFSET    6
-#define    RTL8367C_dummy_1b33a_MASK    0xFFC0
-#define    RTL8367C_LED2_PARA_P09_08_OFFSET    4
-#define    RTL8367C_LED2_PARA_P09_08_MASK    0x30
-#define    RTL8367C_LED1_PARA_P09_08_OFFSET    2
-#define    RTL8367C_LED1_PARA_P09_08_MASK    0xC
-#define    RTL8367C_LED0_PARA_P09_08_OFFSET    0
-#define    RTL8367C_LED0_PARA_P09_08_MASK    0x3
-
-#define    RTL8367C_REG_SCAN1_LED_IO_EN3    0x1b34
-#define    RTL8367C_dummy_1b34a_OFFSET    3
-#define    RTL8367C_dummy_1b34a_MASK    0xFFF8
-#define    RTL8367C_LED_SCAN1_BI_PORT9_8_EN_OFFSET    1
-#define    RTL8367C_LED_SCAN1_BI_PORT9_8_EN_MASK    0x6
-#define    RTL8367C_LED_SCAN1_SI_PORT9_8_EN_OFFSET    0
-#define    RTL8367C_LED_SCAN1_SI_PORT9_8_EN_MASK    0x1
-
-#define    RTL8367C_REG_P5_LED_MUX    0x1b35
-#define    RTL8367C_CFG_P5_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P5_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P5_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P5_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P5_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P5_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P6_LED_MUX    0x1b36
-#define    RTL8367C_CFG_P6_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P6_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P6_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P6_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P6_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P6_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P7_LED_MUX    0x1b37
-#define    RTL8367C_CFG_P7_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P7_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P7_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P7_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P7_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P7_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P8_LED_MUX    0x1b38
-#define    RTL8367C_CFG_P8_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P8_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P8_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P8_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P8_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P8_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_P9_LED_MUX    0x1b39
-#define    RTL8367C_CFG_P9_LED2_MUX_OFFSET    10
-#define    RTL8367C_CFG_P9_LED2_MUX_MASK    0x7C00
-#define    RTL8367C_CFG_P9_LED1_MUX_OFFSET    5
-#define    RTL8367C_CFG_P9_LED1_MUX_MASK    0x3E0
-#define    RTL8367C_CFG_P9_LED0_MUX_OFFSET    0
-#define    RTL8367C_CFG_P9_LED0_MUX_MASK    0x1F
-
-#define    RTL8367C_REG_SERIAL_LED_CTRL    0x1b3a
-#define    RTL8367C_SERIAL_LED_SHIFT_SEQUENCE_OFFSET    13
-#define    RTL8367C_SERIAL_LED_SHIFT_SEQUENCE_MASK    0x6000
-#define    RTL8367C_SERIAL_LED_SHIFT_SEQUENCE_EN_OFFSET    12
-#define    RTL8367C_SERIAL_LED_SHIFT_SEQUENCE_EN_MASK    0x1000
-#define    RTL8367C_SERIAL_LED_GROUP_NUM_OFFSET    10
-#define    RTL8367C_SERIAL_LED_GROUP_NUM_MASK    0xC00
-#define    RTL8367C_SERIAL_LED_PORT_EN_OFFSET    0
-#define    RTL8367C_SERIAL_LED_PORT_EN_MASK    0x3FF
-
-/* (16'h1c00)IGMP_EAV */
-
-#define    RTL8367C_REG_IGMP_MLD_CFG0    0x1c00
-#define    RTL8367C_IGMP_MLD_PORTISO_LEAKY_OFFSET    15
-#define    RTL8367C_IGMP_MLD_PORTISO_LEAKY_MASK    0x8000
-#define    RTL8367C_IGMP_MLD_VLAN_LEAKY_OFFSET    14
-#define    RTL8367C_IGMP_MLD_VLAN_LEAKY_MASK    0x4000
-#define    RTL8367C_IGMP_MLD_DISCARD_STORM_FILTER_OFFSET    13
-#define    RTL8367C_IGMP_MLD_DISCARD_STORM_FILTER_MASK    0x2000
-#define    RTL8367C_REPORT_FORWARD_OFFSET    12
-#define    RTL8367C_REPORT_FORWARD_MASK    0x1000
-#define    RTL8367C_ROBURSTNESS_VAR_OFFSET    9
-#define    RTL8367C_ROBURSTNESS_VAR_MASK    0xE00
-#define    RTL8367C_LEAVE_SUPPRESSION_OFFSET    8
-#define    RTL8367C_LEAVE_SUPPRESSION_MASK    0x100
-#define    RTL8367C_REPORT_SUPPRESSION_OFFSET    7
-#define    RTL8367C_REPORT_SUPPRESSION_MASK    0x80
-#define    RTL8367C_LEAVE_TIMER_OFFSET    4
-#define    RTL8367C_LEAVE_TIMER_MASK    0x70
-#define    RTL8367C_FAST_LEAVE_EN_OFFSET    3
-#define    RTL8367C_FAST_LEAVE_EN_MASK    0x8
-#define    RTL8367C_CKS_ERR_OP_OFFSET    1
-#define    RTL8367C_CKS_ERR_OP_MASK    0x6
-#define    RTL8367C_IGMP_MLD_EN_OFFSET    0
-#define    RTL8367C_IGMP_MLD_EN_MASK    0x1
-
-#define    RTL8367C_REG_IGMP_MLD_CFG1    0x1c01
-#define    RTL8367C_DROP_LEAVE_ZERO_OFFSET    2
-#define    RTL8367C_DROP_LEAVE_ZERO_MASK    0x4
-#define    RTL8367C_TABLE_FULL_OP_OFFSET    0
-#define    RTL8367C_TABLE_FULL_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_MLD_CFG2    0x1c02
-
-#define    RTL8367C_REG_IGMP_DYNAMIC_ROUTER_PORT    0x1c03
-#define    RTL8367C_D_ROUTER_PORT_2_OFFSET    11
-#define    RTL8367C_D_ROUTER_PORT_2_MASK    0x7800
-#define    RTL8367C_D_ROUTER_PORT_TMR_2_OFFSET    8
-#define    RTL8367C_D_ROUTER_PORT_TMR_2_MASK    0x700
-#define    RTL8367C_D_ROUTER_PORT_1_OFFSET    3
-#define    RTL8367C_D_ROUTER_PORT_1_MASK    0x78
-#define    RTL8367C_D_ROUTER_PORT_TMR_1_OFFSET    0
-#define    RTL8367C_D_ROUTER_PORT_TMR_1_MASK    0x7
-
-#define    RTL8367C_REG_IGMP_STATIC_ROUTER_PORT    0x1c04
-#define    RTL8367C_IGMP_STATIC_ROUTER_PORT_OFFSET    0
-#define    RTL8367C_IGMP_STATIC_ROUTER_PORT_MASK    0x7FF
-
-#define    RTL8367C_REG_IGMP_PORT0_CONTROL    0x1c05
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT0_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT0_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT0_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT0_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT0_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT0_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT0_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT0_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT0_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT0_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT1_CONTROL    0x1c06
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT1_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT1_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT1_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT1_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT1_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT1_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT1_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT1_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT1_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT1_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT1_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT2_CONTROL    0x1c07
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT2_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT2_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT2_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT2_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT2_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT2_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT2_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT2_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT2_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT2_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT2_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT3_CONTROL    0x1c08
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT3_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT3_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT3_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT3_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT3_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT3_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT3_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT3_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT3_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT3_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT3_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT4_CONTROL    0x1c09
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT4_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT4_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT4_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT4_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT4_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT4_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT4_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT4_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT4_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT4_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT4_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT5_CONTROL    0x1c0a
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT5_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT5_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT5_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT5_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT5_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT5_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT5_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT5_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT5_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT5_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT5_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT6_CONTROL    0x1c0b
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT6_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT6_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT6_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT6_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT6_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT6_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT6_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT6_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT6_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT6_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT6_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT7_CONTROL    0x1c0c
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT7_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT7_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT7_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT7_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT7_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT7_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT7_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT7_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT7_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT7_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT7_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT01_MAX_GROUP    0x1c0d
-#define    RTL8367C_PORT1_MAX_GROUP_OFFSET    8
-#define    RTL8367C_PORT1_MAX_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT0_MAX_GROUP_OFFSET    0
-#define    RTL8367C_PORT0_MAX_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT23_MAX_GROUP    0x1c0e
-#define    RTL8367C_PORT3_MAX_GROUP_OFFSET    8
-#define    RTL8367C_PORT3_MAX_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT2_MAX_GROUP_OFFSET    0
-#define    RTL8367C_PORT2_MAX_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT45_MAX_GROUP    0x1c0f
-#define    RTL8367C_PORT5_MAX_GROUP_OFFSET    8
-#define    RTL8367C_PORT5_MAX_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT4_MAX_GROUP_OFFSET    0
-#define    RTL8367C_PORT4_MAX_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT67_MAX_GROUP    0x1c10
-#define    RTL8367C_PORT7_MAX_GROUP_OFFSET    8
-#define    RTL8367C_PORT7_MAX_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT6_MAX_GROUP_OFFSET    0
-#define    RTL8367C_PORT6_MAX_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT01_CURRENT_GROUP    0x1c11
-#define    RTL8367C_PORT1_CURRENT_GROUP_OFFSET    8
-#define    RTL8367C_PORT1_CURRENT_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT0_CURRENT_GROUP_OFFSET    0
-#define    RTL8367C_PORT0_CURRENT_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT23_CURRENT_GROUP    0x1c12
-#define    RTL8367C_PORT3_CURRENT_GROUP_OFFSET    8
-#define    RTL8367C_PORT3_CURRENT_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT2_CURRENT_GROUP_OFFSET    0
-#define    RTL8367C_PORT2_CURRENT_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT45_CURRENT_GROUP    0x1c13
-#define    RTL8367C_PORT5_CURRENT_GROUP_OFFSET    8
-#define    RTL8367C_PORT5_CURRENT_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT4_CURRENT_GROUP_OFFSET    0
-#define    RTL8367C_PORT4_CURRENT_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT67_CURRENT_GROUP    0x1c14
-#define    RTL8367C_PORT7_CURRENT_GROUP_OFFSET    8
-#define    RTL8367C_PORT7_CURRENT_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT6_CURRENT_GROUP_OFFSET    0
-#define    RTL8367C_PORT6_CURRENT_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_MLD_CFG3    0x1c15
-#define    RTL8367C_IGMP_MLD_IP6_BYPASS_OFFSET    5
-#define    RTL8367C_IGMP_MLD_IP6_BYPASS_MASK    0x20
-#define    RTL8367C_IGMP_MLD_IP4_BYPASS_239_255_255_OFFSET    4
-#define    RTL8367C_IGMP_MLD_IP4_BYPASS_239_255_255_MASK    0x10
-#define    RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_1_OFFSET    3
-#define    RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_1_MASK    0x8
-#define    RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_0_OFFSET    2
-#define    RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_0_MASK    0x4
-#define    RTL8367C_REPORT_LEAVE_FORWARD_OFFSET    0
-#define    RTL8367C_REPORT_LEAVE_FORWARD_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_MLD_CFG4    0x1c16
-#define    RTL8367C_IGMP_MLD_CFG4_OFFSET    0
-#define    RTL8367C_IGMP_MLD_CFG4_MASK    0x7FF
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST0    0x1c20
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST1    0x1c21
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST2    0x1c22
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST3    0x1c23
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST4    0x1c24
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST5    0x1c25
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST6    0x1c26
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST7    0x1c27
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST8    0x1c28
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST9    0x1c29
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST10    0x1c2a
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST11    0x1c2b
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST12    0x1c2c
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST13    0x1c2d
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST14    0x1c2e
-
-#define    RTL8367C_REG_IGMP_GROUP_USAGE_LIST15    0x1c2f
-
-#define    RTL8367C_REG_EAV_CTRL0    0x1c30
-#define    RTL8367C_EAV_CTRL0_OFFSET    0
-#define    RTL8367C_EAV_CTRL0_MASK    0xFF
-
-#define    RTL8367C_REG_EAV_CTRL1    0x1c31
-#define    RTL8367C_REMAP_EAV_PRI3_REGEN_OFFSET    9
-#define    RTL8367C_REMAP_EAV_PRI3_REGEN_MASK    0xE00
-#define    RTL8367C_REMAP_EAV_PRI2_REGEN_OFFSET    6
-#define    RTL8367C_REMAP_EAV_PRI2_REGEN_MASK    0x1C0
-#define    RTL8367C_REMAP_EAV_PRI1_REGEN_OFFSET    3
-#define    RTL8367C_REMAP_EAV_PRI1_REGEN_MASK    0x38
-#define    RTL8367C_REMAP_EAV_PRI0_REGEN_OFFSET    0
-#define    RTL8367C_REMAP_EAV_PRI0_REGEN_MASK    0x7
-
-#define    RTL8367C_REG_EAV_CTRL2    0x1c32
-#define    RTL8367C_REMAP_EAV_PRI7_REGEN_OFFSET    9
-#define    RTL8367C_REMAP_EAV_PRI7_REGEN_MASK    0xE00
-#define    RTL8367C_REMAP_EAV_PRI6_REGEN_OFFSET    6
-#define    RTL8367C_REMAP_EAV_PRI6_REGEN_MASK    0x1C0
-#define    RTL8367C_REMAP_EAV_PRI5_REGEN_OFFSET    3
-#define    RTL8367C_REMAP_EAV_PRI5_REGEN_MASK    0x38
-#define    RTL8367C_REMAP_EAV_PRI4_REGEN_OFFSET    0
-#define    RTL8367C_REMAP_EAV_PRI4_REGEN_MASK    0x7
-
-#define    RTL8367C_REG_SYS_TIME_FREQ    0x1c43
-
-#define    RTL8367C_REG_SYS_TIME_OFFSET_L    0x1c44
-
-#define    RTL8367C_REG_SYS_TIME_OFFSET_H    0x1c45
-
-#define    RTL8367C_REG_SYS_TIME_OFFSET_512NS_L    0x1c46
-
-#define    RTL8367C_REG_SYS_TIME_OFFSET_512NS_H    0x1c47
-#define    RTL8367C_SYS_TIME_OFFSET_TUNE_OFFSET    5
-#define    RTL8367C_SYS_TIME_OFFSET_TUNE_MASK    0x20
-#define    RTL8367C_SYS_TIME_OFFSET_512NS_H_SYS_TIME_OFFSET_512NS_OFFSET    0
-#define    RTL8367C_SYS_TIME_OFFSET_512NS_H_SYS_TIME_OFFSET_512NS_MASK    0x1F
-
-#define    RTL8367C_REG_SYS_TIME_SEC_TRANSIT    0x1c48
-#define    RTL8367C_SYS_TIME_SEC_TRANSIT_OFFSET    0
-#define    RTL8367C_SYS_TIME_SEC_TRANSIT_MASK    0x1
-
-#define    RTL8367C_REG_SYS_TIME_SEC_HIGH_L    0x1c49
-
-#define    RTL8367C_REG_SYS_TIME_SEC_HIGH_H    0x1c4a
-
-#define    RTL8367C_REG_SYS_TIME_512NS_L    0x1c4b
-
-#define    RTL8367C_REG_SYS_TIME_512NS_H    0x1c4c
-#define    RTL8367C_SYS_TIME_512NS_H_OFFSET    0
-#define    RTL8367C_SYS_TIME_512NS_H_MASK    0x1F
-
-#define    RTL8367C_REG_FALLBACK_CTRL    0x1c70
-#define    RTL8367C_FALLBACK_PL_DEC_EN_OFFSET    15
-#define    RTL8367C_FALLBACK_PL_DEC_EN_MASK    0x8000
-#define    RTL8367C_FALLBACK_MONITOR_TIMEOUT_IGNORE_OFFSET    14
-#define    RTL8367C_FALLBACK_MONITOR_TIMEOUT_IGNORE_MASK    0x4000
-#define    RTL8367C_FALLBACK_ERROR_RATIO_THRESHOLD_OFFSET    11
-#define    RTL8367C_FALLBACK_ERROR_RATIO_THRESHOLD_MASK    0x3800
-#define    RTL8367C_FALLBACK_MONITORMAX_OFFSET    8
-#define    RTL8367C_FALLBACK_MONITORMAX_MASK    0x700
-#define    RTL8367C_FALLBACK_MONITOR_TIMEOUT_OFFSET    0
-#define    RTL8367C_FALLBACK_MONITOR_TIMEOUT_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_PORT0_CFG0    0x1c71
-#define    RTL8367C_FALLBACK_PORT0_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT0_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT0_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT0_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT0_CFG1    0x1c72
-
-#define    RTL8367C_REG_FALLBACK_PORT0_CFG2    0x1c73
-#define    RTL8367C_FALLBACK_PORT0_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT0_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT0_CFG3    0x1c74
-#define    RTL8367C_FALLBACK_PORT0_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT0_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_PORT1_CFG0    0x1c75
-#define    RTL8367C_FALLBACK_PORT1_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT1_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT1_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT1_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT1_CFG1    0x1c76
-
-#define    RTL8367C_REG_FALLBACK_PORT1_CFG2    0x1c77
-#define    RTL8367C_FALLBACK_PORT1_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT1_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT1_CFG3    0x1c78
-#define    RTL8367C_FALLBACK_PORT1_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT1_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_PORT2_CFG0    0x1c79
-#define    RTL8367C_FALLBACK_PORT2_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT2_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT2_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT2_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT2_CFG1    0x1c7a
-
-#define    RTL8367C_REG_FALLBACK_PORT2_CFG2    0x1c7b
-#define    RTL8367C_FALLBACK_PORT2_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT2_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT2_CFG3    0x1c7c
-#define    RTL8367C_FALLBACK_PORT2_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT2_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_PORT3_CFG0    0x1c7d
-#define    RTL8367C_FALLBACK_PORT3_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT3_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT3_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT3_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT3_CFG1    0x1c7e
-
-#define    RTL8367C_REG_FALLBACK_PORT3_CFG2    0x1c7f
-#define    RTL8367C_FALLBACK_PORT3_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT3_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT3_CFG3    0x1c80
-#define    RTL8367C_FALLBACK_PORT3_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT3_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_PORT4_CFG0    0x1c81
-#define    RTL8367C_FALLBACK_PORT4_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT4_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT4_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT4_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT4_CFG1    0x1c82
-
-#define    RTL8367C_REG_FALLBACK_PORT4_CFG2    0x1c83
-#define    RTL8367C_FALLBACK_PORT4_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT4_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT4_CFG3    0x1c84
-#define    RTL8367C_FALLBACK_PORT4_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT4_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_CTRL1    0x1c85
-#define    RTL8367C_FALLBACK_VALIDFLOW_OFFSET    8
-#define    RTL8367C_FALLBACK_VALIDFLOW_MASK    0xFF00
-#define    RTL8367C_FALLBACK_STOP_TMR_OFFSET    0
-#define    RTL8367C_FALLBACK_STOP_TMR_MASK    0x1
-
-#define    RTL8367C_REG_FALLBACK_CPL    0x1c86
-#define    RTL8367C_PORT4_CPL_OFFSET    4
-#define    RTL8367C_PORT4_CPL_MASK    0x10
-#define    RTL8367C_PORT3_CPL_OFFSET    3
-#define    RTL8367C_PORT3_CPL_MASK    0x8
-#define    RTL8367C_PORT2_CPL_OFFSET    2
-#define    RTL8367C_PORT2_CPL_MASK    0x4
-#define    RTL8367C_PORT1_CPL_OFFSET    1
-#define    RTL8367C_PORT1_CPL_MASK    0x2
-#define    RTL8367C_PORT0_CPL_OFFSET    0
-#define    RTL8367C_PORT0_CPL_MASK    0x1
-
-#define    RTL8367C_REG_FALLBACK_PHY_PAGE    0x1c87
-#define    RTL8367C_FALLBACK_PHY_PAGE_OFFSET    0
-#define    RTL8367C_FALLBACK_PHY_PAGE_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PHY_REG    0x1c88
-#define    RTL8367C_FALLBACK_PHY_REG_OFFSET    0
-#define    RTL8367C_FALLBACK_PHY_REG_MASK    0x1F
-
-#define    RTL8367C_REG_AFBK_INFO_X0    0x1c89
-
-#define    RTL8367C_REG_AFBK_INFO_X1    0x1c8a
-
-#define    RTL8367C_REG_AFBK_INFO_X2    0x1c8b
-
-#define    RTL8367C_REG_AFBK_INFO_X3    0x1c8c
-
-#define    RTL8367C_REG_AFBK_INFO_X4    0x1c8d
-
-#define    RTL8367C_REG_AFBK_INFO_X5    0x1c8e
-
-#define    RTL8367C_REG_AFBK_INFO_X6    0x1c8f
-
-#define    RTL8367C_REG_AFBK_INFO_X7    0x1c90
-
-#define    RTL8367C_REG_AFBK_INFO_X8    0x1c91
-
-#define    RTL8367C_REG_AFBK_INFO_X9    0x1c92
-
-#define    RTL8367C_REG_AFBK_INFO_X10    0x1c93
-
-#define    RTL8367C_REG_AFBK_INFO_X11    0x1c94
-
-#define    RTL8367C_REG_FALLBACK_PORT5_CFG0    0x1ca0
-#define    RTL8367C_FALLBACK_PORT5_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT5_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT5_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT5_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT5_CFG1    0x1ca1
-
-#define    RTL8367C_REG_FALLBACK_PORT5_CFG2    0x1ca2
-#define    RTL8367C_FALLBACK_PORT5_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT5_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT5_CFG3    0x1ca3
-#define    RTL8367C_FALLBACK_PORT5_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT5_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_PORT6_CFG0    0x1ca4
-#define    RTL8367C_FALLBACK_PORT6_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT6_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT6_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT6_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT6_CFG1    0x1ca5
-
-#define    RTL8367C_REG_FALLBACK_PORT6_CFG2    0x1ca6
-#define    RTL8367C_FALLBACK_PORT6_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT6_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT6_CFG3    0x1ca7
-#define    RTL8367C_FALLBACK_PORT6_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT6_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_FALLBACK_PORT7_CFG0    0x1ca8
-#define    RTL8367C_FALLBACK_PORT7_CFG0_RESET_POWER_LEVEL_OFFSET    15
-#define    RTL8367C_FALLBACK_PORT7_CFG0_RESET_POWER_LEVEL_MASK    0x8000
-#define    RTL8367C_FALLBACK_PORT7_CFG0_ENABLE_OFFSET    14
-#define    RTL8367C_FALLBACK_PORT7_CFG0_ENABLE_MASK    0x4000
-
-#define    RTL8367C_REG_FALLBACK_PORT7_CFG1    0x1ca9
-
-#define    RTL8367C_REG_FALLBACK_PORT7_CFG2    0x1caa
-#define    RTL8367C_FALLBACK_PORT7_CFG2_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT7_CFG2_MASK    0xFFF
-
-#define    RTL8367C_REG_FALLBACK_PORT7_CFG3    0x1cab
-#define    RTL8367C_FALLBACK_PORT7_CFG3_OFFSET    0
-#define    RTL8367C_FALLBACK_PORT7_CFG3_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT8_CONTROL    0x1cb0
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT8_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT8_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT8_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT8_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT8_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT8_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT8_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT8_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT8_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT8_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT8_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT9_CONTROL    0x1cb1
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT9_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT9_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT9_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT9_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT9_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT9_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT9_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT9_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT9_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT9_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT9_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT10_CONTROL    0x1cb2
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_QUERY_OFFSET    14
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_QUERY_MASK    0x4000
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_REPORT_OFFSET    13
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_REPORT_MASK    0x2000
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_LEAVE_OFFSET    12
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_LEAVE_MASK    0x1000
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_MRP_OFFSET    11
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_MRP_MASK    0x800
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_MC_DATA_OFFSET    10
-#define    RTL8367C_IGMP_PORT10_CONTROL_ALLOW_MC_DATA_MASK    0x400
-#define    RTL8367C_IGMP_PORT10_CONTROL_MLDv2_OP_OFFSET    8
-#define    RTL8367C_IGMP_PORT10_CONTROL_MLDv2_OP_MASK    0x300
-#define    RTL8367C_IGMP_PORT10_CONTROL_MLDv1_OP_OFFSET    6
-#define    RTL8367C_IGMP_PORT10_CONTROL_MLDv1_OP_MASK    0xC0
-#define    RTL8367C_IGMP_PORT10_CONTROL_IGMPV3_OP_OFFSET    4
-#define    RTL8367C_IGMP_PORT10_CONTROL_IGMPV3_OP_MASK    0x30
-#define    RTL8367C_IGMP_PORT10_CONTROL_IGMPV2_OP_OFFSET    2
-#define    RTL8367C_IGMP_PORT10_CONTROL_IGMPV2_OP_MASK    0xC
-#define    RTL8367C_IGMP_PORT10_CONTROL_IGMPV1_OP_OFFSET    0
-#define    RTL8367C_IGMP_PORT10_CONTROL_IGMPV1_OP_MASK    0x3
-
-#define    RTL8367C_REG_IGMP_PORT89_MAX_GROUP    0x1cb3
-#define    RTL8367C_PORT9_MAX_GROUP_OFFSET    8
-#define    RTL8367C_PORT9_MAX_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT8_MAX_GROUP_OFFSET    0
-#define    RTL8367C_PORT8_MAX_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT10_MAX_GROUP    0x1cb4
-#define    RTL8367C_IGMP_PORT10_MAX_GROUP_OFFSET    0
-#define    RTL8367C_IGMP_PORT10_MAX_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT89_CURRENT_GROUP    0x1cb5
-#define    RTL8367C_PORT9_CURRENT_GROUP_OFFSET    8
-#define    RTL8367C_PORT9_CURRENT_GROUP_MASK    0xFF00
-#define    RTL8367C_PORT8_CURRENT_GROUP_OFFSET    0
-#define    RTL8367C_PORT8_CURRENT_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_PORT10_CURRENT_GROUP    0x1cb6
-#define    RTL8367C_IGMP_PORT10_CURRENT_GROUP_OFFSET    0
-#define    RTL8367C_IGMP_PORT10_CURRENT_GROUP_MASK    0xFF
-
-#define    RTL8367C_REG_IGMP_L3_CHECKSUM_CHECK    0x1cb7
-#define    RTL8367C_IGMP_L3_CHECKSUM_CHECK_OFFSET    0
-#define    RTL8367C_IGMP_L3_CHECKSUM_CHECK_MASK    0x1
-
-/* (16'h1d00)chip_70b_reg */
-
-#define    RTL8367C_REG_PCSXF_CFG    0x1d00
-#define    RTL8367C_PCSXF_CFG_Reserved_OFFSET    15
-#define    RTL8367C_PCSXF_CFG_Reserved_MASK    0x8000
-#define    RTL8367C_CFG_RST_RXFIFO_P7_5_OFFSET    12
-#define    RTL8367C_CFG_RST_RXFIFO_P7_5_MASK    0x7000
-#define    RTL8367C_CFG_PCSXF_OFFSET    8
-#define    RTL8367C_CFG_PCSXF_MASK    0xF00
-#define    RTL8367C_CFG_RST_RXFIFO_OFFSET    3
-#define    RTL8367C_CFG_RST_RXFIFO_MASK    0xF8
-#define    RTL8367C_CFG_COL2RXDV_OFFSET    2
-#define    RTL8367C_CFG_COL2RXDV_MASK    0x4
-#define    RTL8367C_CFG_PHY_SDET_OFFSET    0
-#define    RTL8367C_CFG_PHY_SDET_MASK    0x3
-
-#define    RTL8367C_REG_PHYID_CFG0    0x1d01
-#define    RTL8367C_CFG_PHY_BRD_MODE_P7_5_OFFSET    11
-#define    RTL8367C_CFG_PHY_BRD_MODE_P7_5_MASK    0x3800
-#define    RTL8367C_CFG_PHYAD_14C_OFFSET    10
-#define    RTL8367C_CFG_PHYAD_14C_MASK    0x400
-#define    RTL8367C_CFG_PHY_BRD_MODE_OFFSET    5
-#define    RTL8367C_CFG_PHY_BRD_MODE_MASK    0x3E0
-#define    RTL8367C_CFG_BRD_PHYAD_OFFSET    0
-#define    RTL8367C_CFG_BRD_PHYAD_MASK    0x1F
-
-#define    RTL8367C_REG_PHYID_CFG1    0x1d02
-#define    RTL8367C_CFG_MSK_MDI_OFFSET    5
-#define    RTL8367C_CFG_MSK_MDI_MASK    0x1FE0
-#define    RTL8367C_CFG_BASE_PHYAD_OFFSET    0
-#define    RTL8367C_CFG_BASE_PHYAD_MASK    0x1F
-
-#define    RTL8367C_REG_PHY_POLL_CFG0    0x1d03
-#define    RTL8367C_CFG_HOTCMD_PRD_EN_OFFSET    15
-#define    RTL8367C_CFG_HOTCMD_PRD_EN_MASK    0x8000
-#define    RTL8367C_CFG_HOTCMD_EN_OFFSET    12
-#define    RTL8367C_CFG_HOTCMD_EN_MASK    0x7000
-#define    RTL8367C_CFG_POLL_PERIOD_OFFSET    8
-#define    RTL8367C_CFG_POLL_PERIOD_MASK    0xF00
-#define    RTL8367C_CFG_PERI_CMDS_RD_OFFSET    4
-#define    RTL8367C_CFG_PERI_CMDS_RD_MASK    0xF0
-#define    RTL8367C_CFG_PERI_CMDS_WR_OFFSET    0
-#define    RTL8367C_CFG_PERI_CMDS_WR_MASK    0xF
-
-#define    RTL8367C_REG_PHY_POLL_CFG1    0x1d04
-
-#define    RTL8367C_REG_PHY_POLL_CFG2    0x1d05
-
-#define    RTL8367C_REG_PHY_POLL_CFG3    0x1d06
-
-#define    RTL8367C_REG_PHY_POLL_CFG4    0x1d07
-
-#define    RTL8367C_REG_PHY_POLL_CFG5    0x1d08
-
-#define    RTL8367C_REG_PHY_POLL_CFG6    0x1d09
-
-#define    RTL8367C_REG_PHY_POLL_CFG7    0x1d0a
-
-#define    RTL8367C_REG_PHY_POLL_CFG8    0x1d0b
-
-#define    RTL8367C_REG_PHY_POLL_CFG9    0x1d0c
-
-#define    RTL8367C_REG_PHY_POLL_CFG10    0x1d0d
-
-#define    RTL8367C_REG_PHY_POLL_CFG11    0x1d0e
-
-#define    RTL8367C_REG_PHY_POLL_CFG12    0x1d0f
-
-#define    RTL8367C_REG_EFUSE_MISC    0x1d10
-#define    RTL8367C_CFG_SA_SEL_OFFSET    5
-#define    RTL8367C_CFG_SA_SEL_MASK    0x20
-#define    RTL8367C_CFG_PHYAD00_OFFSET    0
-#define    RTL8367C_CFG_PHYAD00_MASK    0x1F
-
-#define    RTL8367C_REG_SDS_MISC    0x1d11
-#define    RTL8367C_CFG_SGMII_RXFC_OFFSET    14
-#define    RTL8367C_CFG_SGMII_RXFC_MASK    0x4000
-#define    RTL8367C_CFG_SGMII_TXFC_OFFSET    13
-#define    RTL8367C_CFG_SGMII_TXFC_MASK    0x2000
-#define    RTL8367C_INB_ARB_OFFSET    12
-#define    RTL8367C_INB_ARB_MASK    0x1000
-#define    RTL8367C_CFG_MAC8_SEL_HSGMII_OFFSET    11
-#define    RTL8367C_CFG_MAC8_SEL_HSGMII_MASK    0x800
-#define    RTL8367C_CFG_SGMII_FDUP_OFFSET    10
-#define    RTL8367C_CFG_SGMII_FDUP_MASK    0x400
-#define    RTL8367C_CFG_SGMII_LINK_OFFSET    9
-#define    RTL8367C_CFG_SGMII_LINK_MASK    0x200
-#define    RTL8367C_CFG_SGMII_SPD_OFFSET    7
-#define    RTL8367C_CFG_SGMII_SPD_MASK    0x180
-#define    RTL8367C_CFG_MAC8_SEL_SGMII_OFFSET    6
-#define    RTL8367C_CFG_MAC8_SEL_SGMII_MASK    0x40
-#define    RTL8367C_CFG_INB_SEL_OFFSET    3
-#define    RTL8367C_CFG_INB_SEL_MASK    0x38
-#define    RTL8367C_CFG_SDS_MODE_18C_OFFSET    0
-#define    RTL8367C_CFG_SDS_MODE_18C_MASK    0x7
-
-#define    RTL8367C_REG_FIFO_CTRL    0x1d12
-#define    RTL8367C_CFG_LINK_DOWN_CLR_FIFO_OFFSET    11
-#define    RTL8367C_CFG_LINK_DOWN_CLR_FIFO_MASK    0x800
-#define    RTL8367C_CFG_LPBK_OFFSET    10
-#define    RTL8367C_CFG_LPBK_MASK    0x400
-#define    RTL8367C_CFG_NOT_FF_OUT_OFFSET    9
-#define    RTL8367C_CFG_NOT_FF_OUT_MASK    0x200
-#define    RTL8367C_CFG_WATER_LEVEL_FD_OFFSET    6
-#define    RTL8367C_CFG_WATER_LEVEL_FD_MASK    0x1C0
-#define    RTL8367C_CFG_WATER_LEVEL_Y2X_OFFSET    3
-#define    RTL8367C_CFG_WATER_LEVEL_Y2X_MASK    0x38
-#define    RTL8367C_CFG_WATER_LEVEL_X2Y_OFFSET    0
-#define    RTL8367C_CFG_WATER_LEVEL_X2Y_MASK    0x7
-
-#define    RTL8367C_REG_BCAM_SETTING    0x1d13
-#define    RTL8367C_CFG_BCAM_MDS_OFFSET    3
-#define    RTL8367C_CFG_BCAM_MDS_MASK    0x18
-#define    RTL8367C_CFG_BCAM_RDS_OFFSET    0
-#define    RTL8367C_CFG_BCAM_RDS_MASK    0x7
-
-#define    RTL8367C_REG_GPHY_ACS_MISC    0x1d14
-#define    RTL8367C_CFG_SEL_GPHY_SMI_OFFSET    3
-#define    RTL8367C_CFG_SEL_GPHY_SMI_MASK    0x8
-#define    RTL8367C_CFG_BRD_PHYIDX_OFFSET    0
-#define    RTL8367C_CFG_BRD_PHYIDX_MASK    0x7
-
-#define    RTL8367C_REG_GPHY_OCP_MSB_0    0x1d15
-#define    RTL8367C_CFG_CPU_OCPADR_MSB_OFFSET    6
-#define    RTL8367C_CFG_CPU_OCPADR_MSB_MASK    0xFC0
-#define    RTL8367C_CFG_DW8051_OCPADR_MSB_OFFSET    0
-#define    RTL8367C_CFG_DW8051_OCPADR_MSB_MASK    0x3F
-
-#define    RTL8367C_REG_GPHY_OCP_MSB_1    0x1d16
-#define    RTL8367C_CFG_PATCH_OCPADR_MSB_OFFSET    6
-#define    RTL8367C_CFG_PATCH_OCPADR_MSB_MASK    0xFC0
-#define    RTL8367C_CFG_PHYSTS_OCPADR_MSB_OFFSET    0
-#define    RTL8367C_CFG_PHYSTS_OCPADR_MSB_MASK    0x3F
-
-#define    RTL8367C_REG_GPHY_OCP_MSB_2    0x1d17
-#define    RTL8367C_CFG_RRCP_OCPADR_MSB_OFFSET    6
-#define    RTL8367C_CFG_RRCP_OCPADR_MSB_MASK    0xFC0
-#define    RTL8367C_CFG_RTCT_OCPADR_MSB_OFFSET    0
-#define    RTL8367C_CFG_RTCT_OCPADR_MSB_MASK    0x3F
-
-#define    RTL8367C_REG_GPHY_OCP_MSB_3    0x1d18
-#define    RTL8367C_GPHY_OCP_MSB_3_OFFSET    0
-#define    RTL8367C_GPHY_OCP_MSB_3_MASK    0x3F
-
-#define    RTL8367C_REG_GPIO_67C_I_X0    0x1d19
-
-#define    RTL8367C_REG_GPIO_67C_I_X1    0x1d1a
-
-#define    RTL8367C_REG_GPIO_67C_I_X2    0x1d1b
-
-#define    RTL8367C_REG_GPIO_67C_I_X3    0x1d1c
-#define    RTL8367C_GPIO_67C_I_X3_OFFSET    0
-#define    RTL8367C_GPIO_67C_I_X3_MASK    0x3FFF
-
-#define    RTL8367C_REG_GPIO_67C_O_X0    0x1d1d
-
-#define    RTL8367C_REG_GPIO_67C_O_X1    0x1d1e
-
-#define    RTL8367C_REG_GPIO_67C_O_X2    0x1d1f
-
-#define    RTL8367C_REG_GPIO_67C_O_X3    0x1d20
-#define    RTL8367C_GPIO_67C_O_X3_OFFSET    0
-#define    RTL8367C_GPIO_67C_O_X3_MASK    0x3FFF
-
-#define    RTL8367C_REG_GPIO_67C_OE_X0    0x1d21
-
-#define    RTL8367C_REG_GPIO_67C_OE_X1    0x1d22
-
-#define    RTL8367C_REG_GPIO_67C_OE_X2    0x1d23
-
-#define    RTL8367C_REG_GPIO_67C_OE_X3    0x1d24
-#define    RTL8367C_GPIO_67C_OE_X3_OFFSET    0
-#define    RTL8367C_GPIO_67C_OE_X3_MASK    0x3FFF
-
-#define    RTL8367C_REG_GPIO_MODE_67C_X0    0x1d25
-
-#define    RTL8367C_REG_GPIO_MODE_67C_X1    0x1d26
-
-#define    RTL8367C_REG_GPIO_MODE_67C_X2    0x1d27
-
-#define    RTL8367C_REG_GPIO_MODE_67C_X3    0x1d28
-#define    RTL8367C_GPIO_MODE_67C_X3_OFFSET    0
-#define    RTL8367C_GPIO_MODE_67C_X3_MASK    0x3FFF
-
-#define    RTL8367C_REG_WGPHY_MISC_0    0x1d29
-#define    RTL8367C_CFG_INIPHY_DISGIGA_P7_5_OFFSET    13
-#define    RTL8367C_CFG_INIPHY_DISGIGA_P7_5_MASK    0xE000
-#define    RTL8367C_CFG_INIPHY_PWRUP_OFFSET    5
-#define    RTL8367C_CFG_INIPHY_PWRUP_MASK    0x1FE0
-#define    RTL8367C_CFG_INIPHY_DISGIGA_OFFSET    0
-#define    RTL8367C_CFG_INIPHY_DISGIGA_MASK    0x1F
-
-#define    RTL8367C_REG_WGPHY_MISC_1    0x1d2a
-#define    RTL8367C_WGPHY_MISC_1_OFFSET    0
-#define    RTL8367C_WGPHY_MISC_1_MASK    0xFF
-
-#define    RTL8367C_REG_WGPHY_MISC_2    0x1d2b
-#define    RTL8367C_WGPHY_MISC_2_OFFSET    0
-#define    RTL8367C_WGPHY_MISC_2_MASK    0x3FF
-
-#define    RTL8367C_REG_CFG_AFBK_GPHY_0    0x1d2c
-#define    RTL8367C_CFG_AFBK_GPHY_0_OFFSET    0
-#define    RTL8367C_CFG_AFBK_GPHY_0_MASK    0x1F
-
-#define    RTL8367C_REG_CFG_AFBK_GPHY_1    0x1d2d
-#define    RTL8367C_CFG_AFBK_GPHY_1_OFFSET    0
-#define    RTL8367C_CFG_AFBK_GPHY_1_MASK    0xFFF
-
-#define    RTL8367C_REG_EF_SLV_CTRL_0    0x1d2e
-#define    RTL8367C_EF_SLV_BUSY_OFFSET    11
-#define    RTL8367C_EF_SLV_BUSY_MASK    0x800
-#define    RTL8367C_EF_SLV_ACK_OFFSET    10
-#define    RTL8367C_EF_SLV_ACK_MASK    0x400
-#define    RTL8367C_EF_SLV_A_OFFSET    2
-#define    RTL8367C_EF_SLV_A_MASK    0x3FC
-#define    RTL8367C_EF_SLV_WE_OFFSET    1
-#define    RTL8367C_EF_SLV_WE_MASK    0x2
-#define    RTL8367C_EF_SLV_CE_OFFSET    0
-#define    RTL8367C_EF_SLV_CE_MASK    0x1
-
-#define    RTL8367C_REG_EF_SLV_CTRL_1    0x1d2f
-
-#define    RTL8367C_REG_EF_SLV_CTRL_2    0x1d30
-
-#define    RTL8367C_REG_EFUSE_MISC_1    0x1d31
-#define    RTL8367C_EF_EN_EFUSE_OFFSET    10
-#define    RTL8367C_EF_EN_EFUSE_MASK    0x400
-#define    RTL8367C_EF_MODEL_ID_OFFSET    6
-#define    RTL8367C_EF_MODEL_ID_MASK    0x3C0
-#define    RTL8367C_EF_RSVD_OFFSET    2
-#define    RTL8367C_EF_RSVD_MASK    0x3C
-#define    RTL8367C_EF_SYS_CLK_OFFSET    0
-#define    RTL8367C_EF_SYS_CLK_MASK    0x3
-
-#define    RTL8367C_REG_IO_MISC_FUNC    0x1d32
-#define    RTL8367C_TST_MODE_OFFSET    3
-#define    RTL8367C_TST_MODE_MASK    0x8
-#define    RTL8367C_UART_EN_OFFSET    2
-#define    RTL8367C_UART_EN_MASK    0x4
-#define    RTL8367C_INT_EN_OFFSET    1
-#define    RTL8367C_INT_EN_MASK    0x2
-#define    RTL8367C_BUZ_EN_OFFSET    0
-#define    RTL8367C_BUZ_EN_MASK    0x1
-
-#define    RTL8367C_REG_HTRAM_DVS    0x1d33
-#define    RTL8367C_HTRAM_DVS_OFFSET    0
-#define    RTL8367C_HTRAM_DVS_MASK    0x1
-
-#define    RTL8367C_REG_EF_SLV_CTRL_3    0x1d34
-#define    RTL8367C_EF_SLV_CTRL_3_OFFSET    0
-#define    RTL8367C_EF_SLV_CTRL_3_MASK    0x1
-
-#define    RTL8367C_REG_INBAND_EN14C    0x1d35
-#define    RTL8367C_INBAND_EN14C_OFFSET    0
-#define    RTL8367C_INBAND_EN14C_MASK    0x1
-
-#define    RTL8367C_REG_CFG_SWR_L    0x1d36
-#define    RTL8367C_ANARG_RDY_SWR_L_OFFSET    14
-#define    RTL8367C_ANARG_RDY_SWR_L_MASK    0x4000
-#define    RTL8367C_ANARG_VALID_SWR_L_OFFSET    13
-#define    RTL8367C_ANARG_VALID_SWR_L_MASK    0x2000
-#define    RTL8367C_SAW_SWR_L_OFFSET    9
-#define    RTL8367C_SAW_SWR_L_MASK    0x1E00
-#define    RTL8367C_SAW_VALID_SWR_L_OFFSET    8
-#define    RTL8367C_SAW_VALID_SWR_L_MASK    0x100
-#define    RTL8367C_UPS_DBGO_L_OFFSET    0
-#define    RTL8367C_UPS_DBGO_L_MASK    0xFF
-
-#define    RTL8367C_REG_BTCAM_CTRL    0x1d37
-#define    RTL8367C_TCAM_RDS_OFFSET    2
-#define    RTL8367C_TCAM_RDS_MASK    0x1C
-#define    RTL8367C_TCAM_MDS_OFFSET    0
-#define    RTL8367C_TCAM_MDS_MASK    0x3
-
-#define    RTL8367C_REG_PBRAM_BISR_CTRL    0x1d38
-#define    RTL8367C_HAS_HLDRMP_MD_OFFSET    9
-#define    RTL8367C_HAS_HLDRMP_MD_MASK    0x200
-#define    RTL8367C_PB_HLDRMP_MD_OFFSET    8
-#define    RTL8367C_PB_HLDRMP_MD_MASK    0x100
-#define    RTL8367C_HAS_BISR_BIRSTN_OFFSET    7
-#define    RTL8367C_HAS_BISR_BIRSTN_MASK    0x80
-#define    RTL8367C_SEC_RUN_HSA_OFFSET    6
-#define    RTL8367C_SEC_RUN_HSA_MASK    0x40
-#define    RTL8367C_HAS_HLDRMP_VAL_OFFSET    5
-#define    RTL8367C_HAS_HLDRMP_VAL_MASK    0x20
-#define    RTL8367C_HAS_BISR_PWRSTN_OFFSET    4
-#define    RTL8367C_HAS_BISR_PWRSTN_MASK    0x10
-#define    RTL8367C_SEC_RUN_PB_OFFSET    3
-#define    RTL8367C_SEC_RUN_PB_MASK    0x8
-#define    RTL8367C_PB_HLDRMP_VAL_OFFSET    2
-#define    RTL8367C_PB_HLDRMP_VAL_MASK    0x4
-#define    RTL8367C_PB_BISR_BIRSTN_OFFSET    1
-#define    RTL8367C_PB_BISR_BIRSTN_MASK    0x2
-#define    RTL8367C_PB_BISR_PWRSTN_OFFSET    0
-#define    RTL8367C_PB_BISR_PWRSTN_MASK    0x1
-
-#define    RTL8367C_REG_CVLANRAM_BISR_CTRL    0x1d39
-#define    RTL8367C_SEC_RUN_CVLAN_OFFSET    4
-#define    RTL8367C_SEC_RUN_CVLAN_MASK    0x10
-#define    RTL8367C_CVALN_HLDRMP_MD_OFFSET    3
-#define    RTL8367C_CVALN_HLDRMP_MD_MASK    0x8
-#define    RTL8367C_CVALN_HLDRMP_VAL_OFFSET    2
-#define    RTL8367C_CVALN_HLDRMP_VAL_MASK    0x4
-#define    RTL8367C_CVLAN_BISR_BIRSTN_OFFSET    1
-#define    RTL8367C_CVLAN_BISR_BIRSTN_MASK    0x2
-#define    RTL8367C_CVLAN_BISR_PWRSTN_OFFSET    0
-#define    RTL8367C_CVLAN_BISR_PWRSTN_MASK    0x1
-
-#define    RTL8367C_REG_CFG_1588_TIMER_EN_GPI    0x1d3a
-#define    RTL8367C_CFG_1588_TIMER_EN_GPI_OFFSET    0
-#define    RTL8367C_CFG_1588_TIMER_EN_GPI_MASK    0x1
-
-#define    RTL8367C_REG_MDIO_PRMB_SUPP    0x1d3b
-#define    RTL8367C_FIB_HIPRI_OFFSET    14
-#define    RTL8367C_FIB_HIPRI_MASK    0x4000
-#define    RTL8367C_SMT_EN_OFFSET    13
-#define    RTL8367C_SMT_EN_MASK    0x2000
-#define    RTL8367C_P4_FB_CPL_OFFSET    12
-#define    RTL8367C_P4_FB_CPL_MASK    0x1000
-#define    RTL8367C_P3_FB_CPL_OFFSET    11
-#define    RTL8367C_P3_FB_CPL_MASK    0x800
-#define    RTL8367C_P2_FB_CPL_OFFSET    10
-#define    RTL8367C_P2_FB_CPL_MASK    0x400
-#define    RTL8367C_P1_FB_CPL_OFFSET    9
-#define    RTL8367C_P1_FB_CPL_MASK    0x200
-#define    RTL8367C_P0_FB_CPL_OFFSET    8
-#define    RTL8367C_P0_FB_CPL_MASK    0x100
-#define    RTL8367C_DBG_PKG_8367N_OFFSET    7
-#define    RTL8367C_DBG_PKG_8367N_MASK    0x80
-#define    RTL8367C_DBG_PKG_8367VB_OFFSET    6
-#define    RTL8367C_DBG_PKG_8367VB_MASK    0x40
-#define    RTL8367C_CFG_DEBUG_EN_OFFSET    5
-#define    RTL8367C_CFG_DEBUG_EN_MASK    0x20
-#define    RTL8367C_CFG_TMR_ACK_OFFSET    1
-#define    RTL8367C_CFG_TMR_ACK_MASK    0x1E
-#define    RTL8367C_CFG_PRMB_SUPP_OFFSET    0
-#define    RTL8367C_CFG_PRMB_SUPP_MASK    0x1
-
-#define    RTL8367C_REG_BOND4READ    0x1d3c
-#define    RTL8367C_BOND_BOID0_OFFSET    8
-#define    RTL8367C_BOND_BOID0_MASK    0x100
-#define    RTL8367C_BOND_SYSCLK_OFFSET    7
-#define    RTL8367C_BOND_SYSCLK_MASK    0x80
-#define    RTL8367C_BOND_PHYMODE_OFFSET    6
-#define    RTL8367C_BOND_PHYMODE_MASK    0x40
-#define    RTL8367C_BOND_DIS_PON_BIST_OFFSET    5
-#define    RTL8367C_BOND_DIS_PON_BIST_MASK    0x20
-#define    RTL8367C_BOND_DIS_TABLE_INIT_OFFSET    4
-#define    RTL8367C_BOND_DIS_TABLE_INIT_MASK    0x10
-#define    RTL8367C_BOND_BYP_AFE_PLL_OFFSET    3
-#define    RTL8367C_BOND_BYP_AFE_PLL_MASK    0x8
-#define    RTL8367C_BOND_BYP_AFE_POR_OFFSET    2
-#define    RTL8367C_BOND_BYP_AFE_POR_MASK    0x4
-#define    RTL8367C_BOND_BISR_COND_OFFSET    1
-#define    RTL8367C_BOND_BISR_COND_MASK    0x2
-#define    RTL8367C_BOND_EF_EN_OFFSET    0
-#define    RTL8367C_BOND_EF_EN_MASK    0x1
-
-#define    RTL8367C_REG_REG_TO_ECO0    0x1d3d
-
-#define    RTL8367C_REG_REG_TO_ECO1    0x1d3e
-
-#define    RTL8367C_REG_REG_TO_ECO2    0x1d3f
-
-#define    RTL8367C_REG_REG_TO_ECO3    0x1d40
-
-#define    RTL8367C_REG_REG_TO_ECO4    0x1d41
-
-#define    RTL8367C_REG_PHYSTS_CTRL0    0x1d42
-#define    RTL8367C_MACRX_DUPDET_EN_OFFSET    5
-#define    RTL8367C_MACRX_DUPDET_EN_MASK    0x20
-#define    RTL8367C_LNKUP_DLY_EN_OFFSET    4
-#define    RTL8367C_LNKUP_DLY_EN_MASK    0x10
-#define    RTL8367C_GE_100M_LNKUP_DLY_OFFSET    2
-#define    RTL8367C_GE_100M_LNKUP_DLY_MASK    0xC
-#define    RTL8367C_PHYSTS_10M_LNKUP_DLY_OFFSET    0
-#define    RTL8367C_PHYSTS_10M_LNKUP_DLY_MASK    0x3
-
-#define    RTL8367C_REG_SSC_CTRL0_0    0x1d44
-#define    RTL8367C_SSC_CTRL0_0_SSC_TYPE_OFFSET    13
-#define    RTL8367C_SSC_CTRL0_0_SSC_TYPE_MASK    0x2000
-#define    RTL8367C_SSC_CTRL0_0_PHASE_LIM_SEL_OFFSET    5
-#define    RTL8367C_SSC_CTRL0_0_PHASE_LIM_SEL_MASK    0x1FE0
-#define    RTL8367C_SSC_CTRL0_0_PHASE_LIM_EN_OFFSET    4
-#define    RTL8367C_SSC_CTRL0_0_PHASE_LIM_EN_MASK    0x10
-#define    RTL8367C_SSC_CTRL0_0_DLL_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL0_0_DLL_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL0_0_SSC_EN_OFFSET    1
-#define    RTL8367C_SSC_CTRL0_0_SSC_EN_MASK    0x2
-#define    RTL8367C_SSC_CTRL0_0_SSC_MODE_OFFSET    0
-#define    RTL8367C_SSC_CTRL0_0_SSC_MODE_MASK    0x1
-
-#define    RTL8367C_REG_SSC_RDM_SEED    0x1d45
-
-#define    RTL8367C_REG_SSC_PN_POLY_SEL    0x1d46
-
-#define    RTL8367C_REG_SSC_CTRL0_3    0x1d47
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_CNT_OFFSET    8
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_CNT_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_A_OFFSET    7
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_A_MASK    0x80
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_B_OFFSET    6
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_B_MASK    0x40
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_UPDN_OFFSET    5
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_UPDN_MASK    0x20
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_PRD_OFFSET    4
-#define    RTL8367C_SSC_CTRL0_3_PHSFT_PRD_MASK    0x10
-#define    RTL8367C_SSC_CTRL0_3_PN_POLY_DEG_OFFSET    0
-#define    RTL8367C_SSC_CTRL0_3_PN_POLY_DEG_MASK    0xF
-
-#define    RTL8367C_REG_SSC_CTRL0_4    0x1d48
-#define    RTL8367C_SSC_CTRL0_4_SSC_UP1DN0_OFFSET    15
-#define    RTL8367C_SSC_CTRL0_4_SSC_UP1DN0_MASK    0x8000
-#define    RTL8367C_SSC_CTRL0_4_SSC_PERIOD_OFFSET    8
-#define    RTL8367C_SSC_CTRL0_4_SSC_PERIOD_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL0_4_SSC_OFFSET_OFFSET    0
-#define    RTL8367C_SSC_CTRL0_4_SSC_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_SSC_CTRL0_5    0x1d49
-#define    RTL8367C_SSC_CTRL0_5_PH_OFS_TOG_OFFSET    15
-#define    RTL8367C_SSC_CTRL0_5_PH_OFS_TOG_MASK    0x8000
-#define    RTL8367C_SSC_CTRL0_5_PH_OFS_OFFSET    10
-#define    RTL8367C_SSC_CTRL0_5_PH_OFS_MASK    0x7C00
-#define    RTL8367C_SSC_CTRL0_5_SSC_STEP_OFFSET    4
-#define    RTL8367C_SSC_CTRL0_5_SSC_STEP_MASK    0x3F0
-#define    RTL8367C_SSC_CTRL0_5_SSC_TEST_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL0_5_SSC_TEST_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL0_5_SSC_PH_CFG_OFFSET    0
-#define    RTL8367C_SSC_CTRL0_5_SSC_PH_CFG_MASK    0x3
-
-#define    RTL8367C_REG_SSC_STS0    0x1d4a
-#define    RTL8367C_SSC_STS0_OFS_BUSY_OFFSET    13
-#define    RTL8367C_SSC_STS0_OFS_BUSY_MASK    0x2000
-#define    RTL8367C_SSC_STS0_OFS_TOTAL_R_OFFSET    8
-#define    RTL8367C_SSC_STS0_OFS_TOTAL_R_MASK    0x1F00
-#define    RTL8367C_SSC_STS0_CNT_GRY0_OFFSET    4
-#define    RTL8367C_SSC_STS0_CNT_GRY0_MASK    0xF0
-#define    RTL8367C_SSC_STS0_OFS_GRY0_OFFSET    0
-#define    RTL8367C_SSC_STS0_OFS_GRY0_MASK    0xF
-
-#define    RTL8367C_REG_SSC_CTRL1_0    0x1d4b
-#define    RTL8367C_SSC_CTRL1_0_SSC_TYPE_OFFSET    13
-#define    RTL8367C_SSC_CTRL1_0_SSC_TYPE_MASK    0x2000
-#define    RTL8367C_SSC_CTRL1_0_PHASE_LIM_SEL_OFFSET    5
-#define    RTL8367C_SSC_CTRL1_0_PHASE_LIM_SEL_MASK    0x1FE0
-#define    RTL8367C_SSC_CTRL1_0_PHASE_LIM_EN_OFFSET    4
-#define    RTL8367C_SSC_CTRL1_0_PHASE_LIM_EN_MASK    0x10
-#define    RTL8367C_SSC_CTRL1_0_DLL_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL1_0_DLL_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL1_0_SSC_EN_OFFSET    1
-#define    RTL8367C_SSC_CTRL1_0_SSC_EN_MASK    0x2
-#define    RTL8367C_SSC_CTRL1_0_SSC_MODE_OFFSET    0
-#define    RTL8367C_SSC_CTRL1_0_SSC_MODE_MASK    0x1
-
-#define    RTL8367C_REG_SSC_RDM_SEED1    0x1d4c
-
-#define    RTL8367C_REG_SSC_PN_POLY_SEL1    0x1d4d
-
-#define    RTL8367C_REG_SSC_CTRL1_3    0x1d4e
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_CNT_OFFSET    8
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_CNT_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_A_OFFSET    7
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_A_MASK    0x80
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_B_OFFSET    6
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_B_MASK    0x40
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_UPDN_OFFSET    5
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_UPDN_MASK    0x20
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_PRD_OFFSET    4
-#define    RTL8367C_SSC_CTRL1_3_PHSFT_PRD_MASK    0x10
-#define    RTL8367C_SSC_CTRL1_3_PN_POLY_DEG_OFFSET    0
-#define    RTL8367C_SSC_CTRL1_3_PN_POLY_DEG_MASK    0xF
-
-#define    RTL8367C_REG_SSC_CTRL1_4    0x1d4f
-#define    RTL8367C_SSC_CTRL1_4_SSC_UP1DN0_OFFSET    15
-#define    RTL8367C_SSC_CTRL1_4_SSC_UP1DN0_MASK    0x8000
-#define    RTL8367C_SSC_CTRL1_4_SSC_PERIOD_OFFSET    8
-#define    RTL8367C_SSC_CTRL1_4_SSC_PERIOD_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL1_4_SSC_OFFSET_OFFSET    0
-#define    RTL8367C_SSC_CTRL1_4_SSC_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_SSC_CTRL1_5    0x1d50
-#define    RTL8367C_SSC_CTRL1_5_PH_OFS_TOG_OFFSET    15
-#define    RTL8367C_SSC_CTRL1_5_PH_OFS_TOG_MASK    0x8000
-#define    RTL8367C_SSC_CTRL1_5_PH_OFS_OFFSET    10
-#define    RTL8367C_SSC_CTRL1_5_PH_OFS_MASK    0x7C00
-#define    RTL8367C_SSC_CTRL1_5_SSC_STEP_OFFSET    4
-#define    RTL8367C_SSC_CTRL1_5_SSC_STEP_MASK    0x3F0
-#define    RTL8367C_SSC_CTRL1_5_SSC_TEST_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL1_5_SSC_TEST_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL1_5_SSC_PH_CFG_OFFSET    0
-#define    RTL8367C_SSC_CTRL1_5_SSC_PH_CFG_MASK    0x3
-
-#define    RTL8367C_REG_SSC_STS1    0x1d51
-#define    RTL8367C_SSC_STS1_OFS_BUSY_OFFSET    13
-#define    RTL8367C_SSC_STS1_OFS_BUSY_MASK    0x2000
-#define    RTL8367C_SSC_STS1_OFS_TOTAL_R_OFFSET    8
-#define    RTL8367C_SSC_STS1_OFS_TOTAL_R_MASK    0x1F00
-#define    RTL8367C_SSC_STS1_CNT_GRY0_OFFSET    4
-#define    RTL8367C_SSC_STS1_CNT_GRY0_MASK    0xF0
-#define    RTL8367C_SSC_STS1_OFS_GRY0_OFFSET    0
-#define    RTL8367C_SSC_STS1_OFS_GRY0_MASK    0xF
-
-#define    RTL8367C_REG_SSC_CTRL2_0    0x1d52
-#define    RTL8367C_SSC_CTRL2_0_SSC_TYPE_OFFSET    13
-#define    RTL8367C_SSC_CTRL2_0_SSC_TYPE_MASK    0x2000
-#define    RTL8367C_SSC_CTRL2_0_PHASE_LIM_SEL_OFFSET    5
-#define    RTL8367C_SSC_CTRL2_0_PHASE_LIM_SEL_MASK    0x1FE0
-#define    RTL8367C_SSC_CTRL2_0_PHASE_LIM_EN_OFFSET    4
-#define    RTL8367C_SSC_CTRL2_0_PHASE_LIM_EN_MASK    0x10
-#define    RTL8367C_SSC_CTRL2_0_DLL_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL2_0_DLL_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL2_0_SSC_EN_OFFSET    1
-#define    RTL8367C_SSC_CTRL2_0_SSC_EN_MASK    0x2
-#define    RTL8367C_SSC_CTRL2_0_SSC_MODE_OFFSET    0
-#define    RTL8367C_SSC_CTRL2_0_SSC_MODE_MASK    0x1
-
-#define    RTL8367C_REG_SSC_RDM_SEED2    0x1d53
-
-#define    RTL8367C_REG_SSC_PN_POLY_SEL2    0x1d54
-
-#define    RTL8367C_REG_SSC_CTRL2_3    0x1d55
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_CNT_OFFSET    8
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_CNT_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_A_OFFSET    7
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_A_MASK    0x80
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_B_OFFSET    6
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_B_MASK    0x40
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_UPDN_OFFSET    5
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_UPDN_MASK    0x20
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_PRD_OFFSET    4
-#define    RTL8367C_SSC_CTRL2_3_PHSFT_PRD_MASK    0x10
-#define    RTL8367C_SSC_CTRL2_3_PN_POLY_DEG_OFFSET    0
-#define    RTL8367C_SSC_CTRL2_3_PN_POLY_DEG_MASK    0xF
-
-#define    RTL8367C_REG_SSC_CTRL2_4    0x1d56
-#define    RTL8367C_SSC_CTRL2_4_SSC_UP1DN0_OFFSET    15
-#define    RTL8367C_SSC_CTRL2_4_SSC_UP1DN0_MASK    0x8000
-#define    RTL8367C_SSC_CTRL2_4_SSC_PERIOD_OFFSET    8
-#define    RTL8367C_SSC_CTRL2_4_SSC_PERIOD_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL2_4_SSC_OFFSET_OFFSET    0
-#define    RTL8367C_SSC_CTRL2_4_SSC_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_SSC_CTRL2_5    0x1d57
-#define    RTL8367C_SSC_CTRL2_5_PH_OFS_TOG_OFFSET    15
-#define    RTL8367C_SSC_CTRL2_5_PH_OFS_TOG_MASK    0x8000
-#define    RTL8367C_SSC_CTRL2_5_PH_OFS_OFFSET    10
-#define    RTL8367C_SSC_CTRL2_5_PH_OFS_MASK    0x7C00
-#define    RTL8367C_SSC_CTRL2_5_SSC_STEP_OFFSET    4
-#define    RTL8367C_SSC_CTRL2_5_SSC_STEP_MASK    0x3F0
-#define    RTL8367C_SSC_CTRL2_5_SSC_TEST_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL2_5_SSC_TEST_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL2_5_SSC_PH_CFG_OFFSET    0
-#define    RTL8367C_SSC_CTRL2_5_SSC_PH_CFG_MASK    0x3
-
-#define    RTL8367C_REG_SSC_STS2    0x1d58
-#define    RTL8367C_SSC_STS2_OFS_BUSY_OFFSET    13
-#define    RTL8367C_SSC_STS2_OFS_BUSY_MASK    0x2000
-#define    RTL8367C_SSC_STS2_OFS_TOTAL_R_OFFSET    8
-#define    RTL8367C_SSC_STS2_OFS_TOTAL_R_MASK    0x1F00
-#define    RTL8367C_SSC_STS2_CNT_GRY0_OFFSET    4
-#define    RTL8367C_SSC_STS2_CNT_GRY0_MASK    0xF0
-#define    RTL8367C_SSC_STS2_OFS_GRY0_OFFSET    0
-#define    RTL8367C_SSC_STS2_OFS_GRY0_MASK    0xF
-
-#define    RTL8367C_REG_SSC_CTRL3_0    0x1d59
-#define    RTL8367C_SSC_CTRL3_0_SSC_TYPE_OFFSET    13
-#define    RTL8367C_SSC_CTRL3_0_SSC_TYPE_MASK    0x2000
-#define    RTL8367C_SSC_CTRL3_0_PHASE_LIM_SEL_OFFSET    5
-#define    RTL8367C_SSC_CTRL3_0_PHASE_LIM_SEL_MASK    0x1FE0
-#define    RTL8367C_SSC_CTRL3_0_PHASE_LIM_EN_OFFSET    4
-#define    RTL8367C_SSC_CTRL3_0_PHASE_LIM_EN_MASK    0x10
-#define    RTL8367C_SSC_CTRL3_0_DLL_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL3_0_DLL_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL3_0_SSC_EN_OFFSET    1
-#define    RTL8367C_SSC_CTRL3_0_SSC_EN_MASK    0x2
-#define    RTL8367C_SSC_CTRL3_0_SSC_MODE_OFFSET    0
-#define    RTL8367C_SSC_CTRL3_0_SSC_MODE_MASK    0x1
-
-#define    RTL8367C_REG_SSC_RDM_SEED3    0x1d5a
-
-#define    RTL8367C_REG_SSC_PN_POLY_SEL3    0x1d5b
-
-#define    RTL8367C_REG_SSC_CTRL3_3    0x1d5c
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_CNT_OFFSET    8
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_CNT_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_A_OFFSET    7
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_A_MASK    0x80
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_B_OFFSET    6
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_B_MASK    0x40
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_UPDN_OFFSET    5
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_UPDN_MASK    0x20
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_PRD_OFFSET    4
-#define    RTL8367C_SSC_CTRL3_3_PHSFT_PRD_MASK    0x10
-#define    RTL8367C_SSC_CTRL3_3_PN_POLY_DEG_OFFSET    0
-#define    RTL8367C_SSC_CTRL3_3_PN_POLY_DEG_MASK    0xF
-
-#define    RTL8367C_REG_SSC_CTRL3_4    0x1d5d
-#define    RTL8367C_SSC_CTRL3_4_SSC_UP1DN0_OFFSET    15
-#define    RTL8367C_SSC_CTRL3_4_SSC_UP1DN0_MASK    0x8000
-#define    RTL8367C_SSC_CTRL3_4_SSC_PERIOD_OFFSET    8
-#define    RTL8367C_SSC_CTRL3_4_SSC_PERIOD_MASK    0x7F00
-#define    RTL8367C_SSC_CTRL3_4_SSC_OFFSET_OFFSET    0
-#define    RTL8367C_SSC_CTRL3_4_SSC_OFFSET_MASK    0xFF
-
-#define    RTL8367C_REG_SSC_CTRL3_5    0x1d5e
-#define    RTL8367C_SSC_CTRL3_5_PH_OFS_TOG_OFFSET    15
-#define    RTL8367C_SSC_CTRL3_5_PH_OFS_TOG_MASK    0x8000
-#define    RTL8367C_SSC_CTRL3_5_PH_OFS_OFFSET    10
-#define    RTL8367C_SSC_CTRL3_5_PH_OFS_MASK    0x7C00
-#define    RTL8367C_SSC_CTRL3_5_SSC_STEP_OFFSET    4
-#define    RTL8367C_SSC_CTRL3_5_SSC_STEP_MASK    0x3F0
-#define    RTL8367C_SSC_CTRL3_5_SSC_TEST_MODE_OFFSET    2
-#define    RTL8367C_SSC_CTRL3_5_SSC_TEST_MODE_MASK    0xC
-#define    RTL8367C_SSC_CTRL3_5_SSC_PH_CFG_OFFSET    0
-#define    RTL8367C_SSC_CTRL3_5_SSC_PH_CFG_MASK    0x3
-
-#define    RTL8367C_REG_SSC_STS3    0x1d5f
-#define    RTL8367C_SSC_STS3_OFS_BUSY_OFFSET    13
-#define    RTL8367C_SSC_STS3_OFS_BUSY_MASK    0x2000
-#define    RTL8367C_SSC_STS3_OFS_TOTAL_R_OFFSET    8
-#define    RTL8367C_SSC_STS3_OFS_TOTAL_R_MASK    0x1F00
-#define    RTL8367C_SSC_STS3_CNT_GRY0_OFFSET    4
-#define    RTL8367C_SSC_STS3_CNT_GRY0_MASK    0xF0
-#define    RTL8367C_SSC_STS3_OFS_GRY0_OFFSET    0
-#define    RTL8367C_SSC_STS3_OFS_GRY0_MASK    0xF
-
-#define    RTL8367C_REG_PHY_POLL_CFG13    0x1d60
-
-#define    RTL8367C_REG_PHY_POLL_CFG14    0x1d61
-
-#define    RTL8367C_REG_FRC_SYS_CLK    0x1d62
-#define    RTL8367C_SYSCLK_FRC_MD_OFFSET    1
-#define    RTL8367C_SYSCLK_FRC_MD_MASK    0x2
-#define    RTL8367C_SYSCLK_FRC_VAL_OFFSET    0
-#define    RTL8367C_SYSCLK_FRC_VAL_MASK    0x1
-
-#define    RTL8367C_REG_AFE_SSC_CTRL    0x1d63
-#define    RTL8367C_PH_RSTB_TXD1_OFFSET    9
-#define    RTL8367C_PH_RSTB_TXD1_MASK    0x200
-#define    RTL8367C_PH_RSTB_TXC1_OFFSET    8
-#define    RTL8367C_PH_RSTB_TXC1_MASK    0x100
-#define    RTL8367C_PH_RSTB_TXD0_OFFSET    7
-#define    RTL8367C_PH_RSTB_TXD0_MASK    0x80
-#define    RTL8367C_PH_RSTB_TXC0_OFFSET    6
-#define    RTL8367C_PH_RSTB_TXC0_MASK    0x40
-#define    RTL8367C_PH_RSTBSYS_OFFSET    5
-#define    RTL8367C_PH_RSTBSYS_MASK    0x20
-#define    RTL8367C_PH_RSTB8051_OFFSET    4
-#define    RTL8367C_PH_RSTB8051_MASK    0x10
-#define    RTL8367C_OREG_SSC_OFFSET    0
-#define    RTL8367C_OREG_SSC_MASK    0xF
-
-#define    RTL8367C_REG_BUFF_RST_CTRL0    0x1d64
-#define    RTL8367C_BUFFRST_TXESD_EN_OFFSET    13
-#define    RTL8367C_BUFFRST_TXESD_EN_MASK    0x2000
-#define    RTL8367C_BUFF_RST_TIME_LONG_OFFSET    8
-#define    RTL8367C_BUFF_RST_TIME_LONG_MASK    0x1F00
-#define    RTL8367C_BUFF_RST_TIME_SHORT_OFFSET    3
-#define    RTL8367C_BUFF_RST_TIME_SHORT_MASK    0xF8
-#define    RTL8367C_SW_BUFF_RST_OFFSET    2
-#define    RTL8367C_SW_BUFF_RST_MASK    0x4
-#define    RTL8367C_IMS_BUFF_RST_OFFSET    1
-#define    RTL8367C_IMS_BUFF_RST_MASK    0x2
-#define    RTL8367C_IMR_BUFF_RST_OFFSET    0
-#define    RTL8367C_IMR_BUFF_RST_MASK    0x1
-
-#define    RTL8367C_REG_BUFF_RST_CTRL1    0x1d65
-#define    RTL8367C_BUFFRST_SYSOVER_EN_OFFSET    10
-#define    RTL8367C_BUFFRST_SYSOVER_EN_MASK    0x400
-#define    RTL8367C_BUFFRST_SYSOVER_THR_OFFSET    0
-#define    RTL8367C_BUFFRST_SYSOVER_THR_MASK    0x3FF
-
-#define    RTL8367C_REG_BUFF_RST_CTRL2    0x1d66
-#define    RTL8367C_BUFFRST_QOVER_EN_OFFSET    10
-#define    RTL8367C_BUFFRST_QOVER_EN_MASK    0x400
-#define    RTL8367C_BUFFRST_QOVER_THR_OFFSET    0
-#define    RTL8367C_BUFFRST_QOVER_THR_MASK    0x3FF
-
-#define    RTL8367C_REG_BUFF_RST_CTRL3    0x1d67
-#define    RTL8367C_DSC_TIMER_OFFSET    11
-#define    RTL8367C_DSC_TIMER_MASK    0x7800
-#define    RTL8367C_BUFFRST_DSCOVER_THR_OFFSET    1
-#define    RTL8367C_BUFFRST_DSCOVER_THR_MASK    0x7FE
-#define    RTL8367C_BUFFRST_DSCOVER_EN_OFFSET    0
-#define    RTL8367C_BUFFRST_DSCOVER_EN_MASK    0x1
-
-#define    RTL8367C_REG_BUFF_RST_CTRL4    0x1d68
-#define    RTL8367C_INDSC_TIMER_OFFSET    11
-#define    RTL8367C_INDSC_TIMER_MASK    0x7800
-#define    RTL8367C_BUFFRST_INDSCOVER_THR_OFFSET    1
-#define    RTL8367C_BUFFRST_INDSCOVER_THR_MASK    0x7FE
-#define    RTL8367C_BUFFRST_INDSCOVER_EN_OFFSET    0
-#define    RTL8367C_BUFFRST_INDSCOVER_EN_MASK    0x1
-
-#define    RTL8367C_REG_BUFF_RST_CTRL5    0x1d69
-#define    RTL8367C_TX_ESD_MODE_OFFSET    8
-#define    RTL8367C_TX_ESD_MODE_MASK    0x100
-#define    RTL8367C_TX_ESD_LVL_OFFSET    0
-#define    RTL8367C_TX_ESD_LVL_MASK    0xFF
-
-#define    RTL8367C_REG_TOP_CON0    0x1d70
-#define    RTL8367C_TOP_CON0_SDS_PWR_ISO_1_OFFSET    15
-#define    RTL8367C_TOP_CON0_SDS_PWR_ISO_1_MASK    0x8000
-#define    RTL8367C_OCP_TIMEOUT_P7_5_OFFSET    12
-#define    RTL8367C_OCP_TIMEOUT_P7_5_MASK    0x7000
-#define    RTL8367C_FIB_EEE_AB_OFFSET    11
-#define    RTL8367C_FIB_EEE_AB_MASK    0x800
-#define    RTL8367C_ADCCKIEN_OFFSET    10
-#define    RTL8367C_ADCCKIEN_MASK    0x400
-#define    RTL8367C_OCP_TIMEOUT_OFFSET    5
-#define    RTL8367C_OCP_TIMEOUT_MASK    0x3E0
-#define    RTL8367C_TOP_CON0_SDS_PWR_ISO_OFFSET    4
-#define    RTL8367C_TOP_CON0_SDS_PWR_ISO_MASK    0x10
-#define    RTL8367C_RG2_TXC_SEL_OFFSET    3
-#define    RTL8367C_RG2_TXC_SEL_MASK    0x8
-#define    RTL8367C_RG1TXC_SEL_OFFSET    2
-#define    RTL8367C_RG1TXC_SEL_MASK    0x4
-#define    RTL8367C_SYNC_1588_EN_OFFSET    1
-#define    RTL8367C_SYNC_1588_EN_MASK    0x2
-#define    RTL8367C_LS_MODE_OFFSET    0
-#define    RTL8367C_LS_MODE_MASK    0x1
-
-#define    RTL8367C_REG_TOP_CON1    0x1d71
-#define    RTL8367C_TA_CHK_EN_OFFSET    2
-#define    RTL8367C_TA_CHK_EN_MASK    0x4
-#define    RTL8367C_SLV_EG_SEL_OFFSET    1
-#define    RTL8367C_SLV_EG_SEL_MASK    0x2
-#define    RTL8367C_IIC_OP_DRAIN_OFFSET    0
-#define    RTL8367C_IIC_OP_DRAIN_MASK    0x1
-
-#define    RTL8367C_REG_SWR_FPWM    0x1d72
-#define    RTL8367C_SWR_FPWM_OFFSET    0
-#define    RTL8367C_SWR_FPWM_MASK    0x1
-
-#define    RTL8367C_REG_EEEP_CTRL_500M    0x1d73
-
-#define    RTL8367C_REG_SHORT_PRMB    0x1d74
-#define    RTL8367C_SHORT_PRMB_OFFSET    0
-#define    RTL8367C_SHORT_PRMB_MASK    0x1
-
-#define    RTL8367C_REG_INDSC_THR_CTRL    0x1d75
-#define    RTL8367C_INDSC_THR_CTRL_OFFSET    0
-#define    RTL8367C_INDSC_THR_CTRL_MASK    0x7FF
-
-#define    RTL8367C_REG_SET_PAD_CTRL_NEW    0x1d80
-#define    RTL8367C_SET_PAD_CTRL_NEW_OFFSET    0
-#define    RTL8367C_SET_PAD_CTRL_NEW_MASK    0x1
-
-#define    RTL8367C_REG_SET_PAD_DRI_0    0x1d81
-
-#define    RTL8367C_REG_SET_PAD_DRI_1    0x1d82
-
-#define    RTL8367C_REG_SET_PAD_DRI_2    0x1d83
-
-#define    RTL8367C_REG_SET_PAD_SLEW_0    0x1d84
-
-#define    RTL8367C_REG_SET_PAD_SLEW_1    0x1d85
-
-#define    RTL8367C_REG_SET_PAD_SLEW_2    0x1d86
-
-#define    RTL8367C_REG_SET_PAD_SMT_0    0x1d87
-
-#define    RTL8367C_REG_SET_PAD_SMT_1    0x1d88
-
-#define    RTL8367C_REG_SET_PAD_SMT_2    0x1d89
-
-#define    RTL8367C_REG_M_I2C_CTL_STA_REG    0x1d8a
-#define    RTL8367C_TX_RX_DATA_OFFSET    8
-#define    RTL8367C_TX_RX_DATA_MASK    0xFF00
-#define    RTL8367C_DUMB_RW_ERR_OFFSET    7
-#define    RTL8367C_DUMB_RW_ERR_MASK    0x80
-#define    RTL8367C_SLV_ACK_FLAG_OFFSET    6
-#define    RTL8367C_SLV_ACK_FLAG_MASK    0x40
-#define    RTL8367C_M_I2C_BUS_IDLE_OFFSET    5
-#define    RTL8367C_M_I2C_BUS_IDLE_MASK    0x20
-#define    RTL8367C_I2C_CMD_TYPE_OFFSET    1
-#define    RTL8367C_I2C_CMD_TYPE_MASK    0x1E
-#define    RTL8367C_I2C_CMD_EXEC_OFFSET    0
-#define    RTL8367C_I2C_CMD_EXEC_MASK    0x1
-
-#define    RTL8367C_REG_M_I2C_DUMB_RW_ADDR_0    0x1d8b
-
-#define    RTL8367C_REG_M_I2C_DUMB_RW_ADDR_1    0x1d8c
-
-#define    RTL8367C_REG_M_I2C_DUMB_RW_DATA_0    0x1d8d
-
-#define    RTL8367C_REG_M_I2C_DUMB_RW_DATA_1    0x1d8e
-
-#define    RTL8367C_REG_M_I2C_DUMB_RW_CTL    0x1d8f
-#define    RTL8367C_DUMB_I2C_CTL_CODE_OFFSET    8
-#define    RTL8367C_DUMB_I2C_CTL_CODE_MASK    0x7F00
-#define    RTL8367C_DUMB_RW_I2C_FORMAT_OFFSET    4
-#define    RTL8367C_DUMB_RW_I2C_FORMAT_MASK    0x10
-#define    RTL8367C_DUMB_RW_DATA_MODE_OFFSET    2
-#define    RTL8367C_DUMB_RW_DATA_MODE_MASK    0xC
-#define    RTL8367C_DUMB_RW_ADDR_MODE_OFFSET    0
-#define    RTL8367C_DUMB_RW_ADDR_MODE_MASK    0x3
-
-#define    RTL8367C_REG_M_I2C_SYS_CTL    0x1d90
-#define    RTL8367C_M_I2C_SCL_IO_MUX_OFFSET    12
-#define    RTL8367C_M_I2C_SCL_IO_MUX_MASK    0x3000
-#define    RTL8367C_M_I2C_SDA_IO_MUX_OFFSET    10
-#define    RTL8367C_M_I2C_SDA_IO_MUX_MASK    0xC00
-#define    RTL8367C_M_I2C_SDA_OD_EN_OFFSET    9
-#define    RTL8367C_M_I2C_SDA_OD_EN_MASK    0x200
-#define    RTL8367C_M_I2C_SCL_OD_EN_OFFSET    8
-#define    RTL8367C_M_I2C_SCL_OD_EN_MASK    0x100
-#define    RTL8367C_M_I2C_SCL_F_DIV_OFFSET    0
-#define    RTL8367C_M_I2C_SCL_F_DIV_MASK    0xFF
-
-#define    RTL8367C_REG_HT_PB_SRAM_CTRL    0x1da0
-#define    RTL8367C_HTPB_RW_OFFSET    2
-#define    RTL8367C_HTPB_RW_MASK    0x4
-#define    RTL8367C_HTPB_SEL_OFFSET    1
-#define    RTL8367C_HTPB_SEL_MASK    0x2
-#define    RTL8367C_HTPB_CE_OFFSET    0
-#define    RTL8367C_HTPB_CE_MASK    0x1
-
-#define    RTL8367C_REG_HT_PB_SRAM_ADDR    0x1da1
-
-#define    RTL8367C_REG_HT_PB_SRAM_DIN0    0x1da2
-
-#define    RTL8367C_REG_HT_PB_SRAM_DIN1    0x1da3
-
-#define    RTL8367C_REG_HT_PB_SRAM_DOUT0    0x1da4
-
-#define    RTL8367C_REG_HT_PB_SRAM_DOUT1    0x1da5
-
-#define    RTL8367C_REG_PHY_STAT_0    0x1db0
-
-#define    RTL8367C_REG_PHY_STAT_1    0x1db1
-
-#define    RTL8367C_REG_PHY_STAT_2    0x1db2
-
-#define    RTL8367C_REG_PHY_STAT_3    0x1db3
-
-#define    RTL8367C_REG_PHY_STAT_4    0x1db4
-
-#define    RTL8367C_REG_PHY_STAT_5    0x1db5
-
-#define    RTL8367C_REG_PHY_STAT_6    0x1db6
-
-#define    RTL8367C_REG_PHY_STAT_7    0x1db7
-
-#define    RTL8367C_REG_SDS_STAT_0    0x1db8
-
-#define    RTL8367C_REG_SDS_STAT_1    0x1db9
-
-#define    RTL8367C_REG_MAC_LINK_STAT_0    0x1dba
-#define    RTL8367C_MAC_LINK_STAT_CUR_0_OFFSET    8
-#define    RTL8367C_MAC_LINK_STAT_CUR_0_MASK    0xFF00
-#define    RTL8367C_MAC_LINK_STAT_LATCH_0_OFFSET    0
-#define    RTL8367C_MAC_LINK_STAT_LATCH_0_MASK    0xFF
-
-#define    RTL8367C_REG_MAC_LINK_STAT_1    0x1dbb
-#define    RTL8367C_MAC_LINK_STAT_1_Reserved_OFFSET    6
-#define    RTL8367C_MAC_LINK_STAT_1_Reserved_MASK    0xFFC0
-#define    RTL8367C_MAC_LINK_STAT_CUR_1_OFFSET    3
-#define    RTL8367C_MAC_LINK_STAT_CUR_1_MASK    0x38
-#define    RTL8367C_MAC_LINK_STAT_LATCH_1_OFFSET    0
-#define    RTL8367C_MAC_LINK_STAT_LATCH_1_MASK    0x7
-
-#define    RTL8367C_REG_MISC_CONTROL_1    0x1dc0
-#define    RTL8367C_P7_FB_CPL_OFFSET    2
-#define    RTL8367C_P7_FB_CPL_MASK    0x4
-#define    RTL8367C_P6_FB_CPL_OFFSET    1
-#define    RTL8367C_P6_FB_CPL_MASK    0x2
-#define    RTL8367C_P5_FB_CPL_OFFSET    0
-#define    RTL8367C_P5_FB_CPL_MASK    0x1
-
-#define    RTL8367C_REG_SDS_MISC_1    0x1dc1
-#define    RTL8367C_CFG_SGMII_RXFC_1_OFFSET    14
-#define    RTL8367C_CFG_SGMII_RXFC_1_MASK    0x4000
-#define    RTL8367C_CFG_SGMII_TXFC_1_OFFSET    13
-#define    RTL8367C_CFG_SGMII_TXFC_1_MASK    0x2000
-#define    RTL8367C_CFG_MAC9_SEL_HSGMII_OFFSET    11
-#define    RTL8367C_CFG_MAC9_SEL_HSGMII_MASK    0x800
-#define    RTL8367C_CFG_SGMII_FDUP_1_OFFSET    10
-#define    RTL8367C_CFG_SGMII_FDUP_1_MASK    0x400
-#define    RTL8367C_CFG_SGMII_LINK_1_OFFSET    9
-#define    RTL8367C_CFG_SGMII_LINK_1_MASK    0x200
-#define    RTL8367C_CFG_SGMII_SPD_1_OFFSET    7
-#define    RTL8367C_CFG_SGMII_SPD_1_MASK    0x180
-#define    RTL8367C_CFG_MAC9_SEL_SGMII_OFFSET    6
-#define    RTL8367C_CFG_MAC9_SEL_SGMII_MASK    0x40
-#define    RTL8367C_CFG_SDS_MODE_14C_1_OFFSET    0
-#define    RTL8367C_CFG_SDS_MODE_14C_1_MASK    0x7
-
-#define    RTL8367C_REG_FIBER_CFG_2_1    0x1dc2
-#define    RTL8367C_SDS_RX_DISABLE_1_OFFSET    6
-#define    RTL8367C_SDS_RX_DISABLE_1_MASK    0xC0
-#define    RTL8367C_SDS_TX_DISABLE_1_OFFSET    4
-#define    RTL8367C_SDS_TX_DISABLE_1_MASK    0x30
-#define    RTL8367C_FIBER_CFG_2_1_SDS_PWR_ISO_1_OFFSET    2
-#define    RTL8367C_FIBER_CFG_2_1_SDS_PWR_ISO_1_MASK    0xC
-#define    RTL8367C_SDS_FRC_LD_1_OFFSET    0
-#define    RTL8367C_SDS_FRC_LD_1_MASK    0x3
-
-#define    RTL8367C_REG_FIBER_CFG_1_1    0x1dc3
-#define    RTL8367C_SDS_FRC_REG4_1_OFFSET    12
-#define    RTL8367C_SDS_FRC_REG4_1_MASK    0x1000
-#define    RTL8367C_SDS_FRC_REG4_FIB100_1_OFFSET    11
-#define    RTL8367C_SDS_FRC_REG4_FIB100_1_MASK    0x800
-#define    RTL8367C_SDS_FRC_MODE_1_OFFSET    3
-#define    RTL8367C_SDS_FRC_MODE_1_MASK    0x8
-#define    RTL8367C_SDS_MODE_1_OFFSET    0
-#define    RTL8367C_SDS_MODE_1_MASK    0x7
-
-#define    RTL8367C_REG_PHYSTS_CTRL0_1    0x1dc4
-#define    RTL8367C_LNKUP_DLY_EN_EXT2_OFFSET    9
-#define    RTL8367C_LNKUP_DLY_EN_EXT2_MASK    0x200
-#define    RTL8367C_GE_100M_LNKUP_DLY_EXT2_OFFSET    7
-#define    RTL8367C_GE_100M_LNKUP_DLY_EXT2_MASK    0x180
-#define    RTL8367C_PHYSTS_10M_LNKUP_DLY_EXT2_OFFSET    5
-#define    RTL8367C_PHYSTS_10M_LNKUP_DLY_EXT2_MASK    0x60
-#define    RTL8367C_LNKUP_DLY_EN_EXT1_OFFSET    4
-#define    RTL8367C_LNKUP_DLY_EN_EXT1_MASK    0x10
-#define    RTL8367C_GE_100M_LNKUP_DLY_EXT1_OFFSET    2
-#define    RTL8367C_GE_100M_LNKUP_DLY_EXT1_MASK    0xC
-#define    RTL8367C_PHYSTS_10M_LNKUP_DLY_EXT1_OFFSET    0
-#define    RTL8367C_PHYSTS_10M_LNKUP_DLY_EXT1_MASK    0x3
-
-#define    RTL8367C_REG_FIBER_CFG_3_1    0x1dc5
-#define    RTL8367C_FIBER_CFG_3_1_OFFSET    0
-#define    RTL8367C_FIBER_CFG_3_1_MASK    0xFFF
-
-#define    RTL8367C_REG_FIBER_CFG_4_1    0x1dc6
-
-#define    RTL8367C_REG_BUFF_RST_CTRL2_2    0x1dc7
-#define    RTL8367C_Cfg_buffrst_sysover_thr_1_OFFSET    3
-#define    RTL8367C_Cfg_buffrst_sysover_thr_1_MASK    0x8
-#define    RTL8367C_Cfg_buffrst_qover_thr_OFFSET    2
-#define    RTL8367C_Cfg_buffrst_qover_thr_MASK    0x4
-#define    RTL8367C_Cfg_buffrst_indscover_thr_1_OFFSET    1
-#define    RTL8367C_Cfg_buffrst_indscover_thr_1_MASK    0x2
-#define    RTL8367C_Cfg_buffrst_dscover_thr_1_OFFSET    0
-#define    RTL8367C_Cfg_buffrst_dscover_thr_1_MASK    0x1
-
-#define    RTL8367C_REG_PHY_DEBUG_CNT_CTRL    0x1dc8
-#define    RTL8367C_PHY_MIB_RST_7_OFFSET    15
-#define    RTL8367C_PHY_MIB_RST_7_MASK    0x8000
-#define    RTL8367C_PHY_MIB_RST_6_OFFSET    14
-#define    RTL8367C_PHY_MIB_RST_6_MASK    0x4000
-#define    RTL8367C_PHY_MIB_RST_5_OFFSET    13
-#define    RTL8367C_PHY_MIB_RST_5_MASK    0x2000
-#define    RTL8367C_PHY_MIB_RST_4_OFFSET    12
-#define    RTL8367C_PHY_MIB_RST_4_MASK    0x1000
-#define    RTL8367C_PHY_MIB_RST_3_OFFSET    11
-#define    RTL8367C_PHY_MIB_RST_3_MASK    0x800
-#define    RTL8367C_PHY_MIB_RST_2_OFFSET    10
-#define    RTL8367C_PHY_MIB_RST_2_MASK    0x400
-#define    RTL8367C_PHY_MIB_RST_1_OFFSET    9
-#define    RTL8367C_PHY_MIB_RST_1_MASK    0x200
-#define    RTL8367C_PHY_MIB_RST_0_OFFSET    8
-#define    RTL8367C_PHY_MIB_RST_0_MASK    0x100
-#define    RTL8367C_PHY_MIB_EN_7_OFFSET    7
-#define    RTL8367C_PHY_MIB_EN_7_MASK    0x80
-#define    RTL8367C_PHY_MIB_EN_6_OFFSET    6
-#define    RTL8367C_PHY_MIB_EN_6_MASK    0x40
-#define    RTL8367C_PHY_MIB_EN_5_OFFSET    5
-#define    RTL8367C_PHY_MIB_EN_5_MASK    0x20
-#define    RTL8367C_PHY_MIB_EN_4_OFFSET    4
-#define    RTL8367C_PHY_MIB_EN_4_MASK    0x10
-#define    RTL8367C_PHY_MIB_EN_3_OFFSET    3
-#define    RTL8367C_PHY_MIB_EN_3_MASK    0x8
-#define    RTL8367C_PHY_MIB_EN_2_OFFSET    2
-#define    RTL8367C_PHY_MIB_EN_2_MASK    0x4
-#define    RTL8367C_PHY_MIB_EN_1_OFFSET    1
-#define    RTL8367C_PHY_MIB_EN_1_MASK    0x2
-#define    RTL8367C_PHY_MIB_EN_0_OFFSET    0
-#define    RTL8367C_PHY_MIB_EN_0_MASK    0x1
-
-#define    RTL8367C_REG_TXPKT_CNT_L_0    0x1dc9
-
-#define    RTL8367C_REG_TXPKT_CNT_H_0    0x1dca
-
-#define    RTL8367C_REG_RXPKT_CNT_L_0    0x1dcb
-
-#define    RTL8367C_REG_RXPKT_CNT_H_0    0x1dcc
-
-#define    RTL8367C_REG_TX_CRC_0    0x1dcd
-
-#define    RTL8367C_REG_RX_CRC_0    0x1dce
-
-#define    RTL8367C_REG_TXPKT_CNT_L_1    0x1dcf
-
-#define    RTL8367C_REG_TXPKT_CNT_H_1    0x1dd0
-
-#define    RTL8367C_REG_RXPKT_CNT_L_1    0x1dd1
-
-#define    RTL8367C_REG_RXPKT_CNT_H_1    0x1dd2
-
-#define    RTL8367C_REG_TX_CRC_1    0x1dd3
-
-#define    RTL8367C_REG_RX_CRC_1    0x1dd4
-
-#define    RTL8367C_REG_TXPKT_CNT_L_2    0x1dd5
-
-#define    RTL8367C_REG_TXPKT_CNT_H_2    0x1dd6
-
-#define    RTL8367C_REG_RXPKT_CNT_L_2    0x1dd7
-
-#define    RTL8367C_REG_RXPKT_CNT_H_2    0x1dd8
-
-#define    RTL8367C_REG_TX_CRC_2    0x1dd9
-
-#define    RTL8367C_REG_RX_CRC_2    0x1dda
-
-#define    RTL8367C_REG_TXPKT_CNT_L_3    0x1ddb
-
-#define    RTL8367C_REG_TXPKT_CNT_H_3    0x1ddc
-
-#define    RTL8367C_REG_RXPKT_CNT_L_3    0x1ddd
-
-#define    RTL8367C_REG_RXPKT_CNT_H_3    0x1dde
-
-#define    RTL8367C_REG_TX_CRC_3    0x1ddf
-
-#define    RTL8367C_REG_RX_CRC_3    0x1de0
-
-#define    RTL8367C_REG_TXPKT_CNT_L_4    0x1de1
-
-#define    RTL8367C_REG_TXPKT_CNT_H_4    0x1de2
-
-#define    RTL8367C_REG_RXPKT_CNT_L_4    0x1de3
-
-#define    RTL8367C_REG_RXPKT_CNT_H_4    0x1de4
-
-#define    RTL8367C_REG_TX_CRC_4    0x1de5
-
-#define    RTL8367C_REG_RX_CRC_4    0x1de6
-
-#define    RTL8367C_REG_TXPKT_CNT_L_5    0x1de7
-
-#define    RTL8367C_REG_TXPKT_CNT_H_5    0x1de8
-
-#define    RTL8367C_REG_RXPKT_CNT_L_5    0x1de9
-
-#define    RTL8367C_REG_RXPKT_CNT_H_5    0x1dea
-
-#define    RTL8367C_REG_TX_CRC_5    0x1deb
-
-#define    RTL8367C_REG_RX_CRC_5    0x1dec
-
-#define    RTL8367C_REG_TXPKT_CNT_L_6    0x1ded
-
-#define    RTL8367C_REG_TXPKT_CNT_H_6    0x1dee
-
-#define    RTL8367C_REG_RXPKT_CNT_L_6    0x1def
-
-#define    RTL8367C_REG_RXPKT_CNT_H_6    0x1df0
-
-#define    RTL8367C_REG_TX_CRC_6    0x1df1
-
-#define    RTL8367C_REG_RX_CRC_6    0x1df2
-
-#define    RTL8367C_REG_TXPKT_CNT_L_7    0x1df3
-
-#define    RTL8367C_REG_TXPKT_CNT_H_7    0x1df4
-
-#define    RTL8367C_REG_RXPKT_CNT_L_7    0x1df5
-
-#define    RTL8367C_REG_RXPKT_CNT_H_7    0x1df6
-
-#define    RTL8367C_REG_TX_CRC_7    0x1df7
-
-#define    RTL8367C_REG_RX_CRC_7    0x1df8
-
-#define    RTL8367C_REG_BOND_DBG_0    0x1df9
-
-#define    RTL8367C_REG_BOND_DBG_1    0x1dfa
-
-#define    RTL8367C_REG_STRP_DBG_0    0x1dfb
-
-#define    RTL8367C_REG_STRP_DBG_1    0x1dfc
-
-#define    RTL8367C_REG_STRP_DBG_2    0x1dfd
-
-/* (16'h1f00)patch_reg */
-
-#define    RTL8367C_REG_INDRECT_ACCESS_CTRL    0x1f00
-#define    RTL8367C_RW_OFFSET    1
-#define    RTL8367C_RW_MASK    0x2
-#define    RTL8367C_CMD_OFFSET    0
-#define    RTL8367C_CMD_MASK    0x1
-
-#define    RTL8367C_REG_INDRECT_ACCESS_STATUS    0x1f01
-#define    RTL8367C_INDRECT_ACCESS_STATUS_OFFSET    2
-#define    RTL8367C_INDRECT_ACCESS_STATUS_MASK    0x7
-
-#define    RTL8367C_REG_INDRECT_ACCESS_ADDRESS    0x1f02
-
-#define    RTL8367C_REG_INDRECT_ACCESS_WRITE_DATA    0x1f03
-
-#define    RTL8367C_REG_INDRECT_ACCESS_READ_DATA    0x1f04
-
-/* (16'h6200)fib_page */
-
-#define    RTL8367C_REG_FIB0_CFG00    0x6200
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_RST_OFFSET    15
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_RST_MASK    0x8000
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_LPK_OFFSET    14
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_LPK_MASK    0x4000
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_SPD_RD_0_OFFSET    13
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_SPD_RD_0_MASK    0x2000
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_ANEN_OFFSET    12
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_ANEN_MASK    0x1000
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_PDOWN_OFFSET    11
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_PDOWN_MASK    0x800
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_ISO_OFFSET    10
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_ISO_MASK    0x400
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_RESTART_OFFSET    9
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_RESTART_MASK    0x200
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_FULLDUP_OFFSET    8
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_FULLDUP_MASK    0x100
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_SPD_RD_1_OFFSET    6
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_SPD_RD_1_MASK    0x40
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_FRCTX_OFFSET    5
-#define    RTL8367C_FIB0_CFG00_CFG_FIB_FRCTX_MASK    0x20
-
-#define    RTL8367C_REG_FIB0_CFG01    0x6201
-#define    RTL8367C_FIB0_CFG01_CAPBILITY_OFFSET    6
-#define    RTL8367C_FIB0_CFG01_CAPBILITY_MASK    0xFFC0
-#define    RTL8367C_FIB0_CFG01_AN_COMPLETE_OFFSET    5
-#define    RTL8367C_FIB0_CFG01_AN_COMPLETE_MASK    0x20
-#define    RTL8367C_FIB0_CFG01_R_FAULT_OFFSET    4
-#define    RTL8367C_FIB0_CFG01_R_FAULT_MASK    0x10
-#define    RTL8367C_FIB0_CFG01_NWAY_ABILITY_OFFSET    3
-#define    RTL8367C_FIB0_CFG01_NWAY_ABILITY_MASK    0x8
-#define    RTL8367C_FIB0_CFG01_LINK_STATUS_OFFSET    2
-#define    RTL8367C_FIB0_CFG01_LINK_STATUS_MASK    0x4
-#define    RTL8367C_FIB0_CFG01_JABBER_DETECT_OFFSET    1
-#define    RTL8367C_FIB0_CFG01_JABBER_DETECT_MASK    0x2
-#define    RTL8367C_FIB0_CFG01_EXTENDED_CAPBILITY_OFFSET    0
-#define    RTL8367C_FIB0_CFG01_EXTENDED_CAPBILITY_MASK    0x1
-
-#define    RTL8367C_REG_FIB0_CFG02    0x6202
-
-#define    RTL8367C_REG_FIB0_CFG03    0x6203
-#define    RTL8367C_FIB0_CFG03_REALTEK_OUI5_0_OFFSET    10
-#define    RTL8367C_FIB0_CFG03_REALTEK_OUI5_0_MASK    0xFC00
-#define    RTL8367C_FIB0_CFG03_MODEL_NO_OFFSET    4
-#define    RTL8367C_FIB0_CFG03_MODEL_NO_MASK    0x3F0
-#define    RTL8367C_FIB0_CFG03_REVISION_NO_OFFSET    0
-#define    RTL8367C_FIB0_CFG03_REVISION_NO_MASK    0xF
-
-#define    RTL8367C_REG_FIB0_CFG04    0x6204
-
-#define    RTL8367C_REG_FIB0_CFG05    0x6205
-
-#define    RTL8367C_REG_FIB0_CFG06    0x6206
-#define    RTL8367C_FIB0_CFG06_FIB_NP_EN_OFFSET    2
-#define    RTL8367C_FIB0_CFG06_FIB_NP_EN_MASK    0x4
-#define    RTL8367C_FIB0_CFG06_RXPAGE_OFFSET    1
-#define    RTL8367C_FIB0_CFG06_RXPAGE_MASK    0x2
-
-#define    RTL8367C_REG_FIB0_CFG07    0x6207
-
-#define    RTL8367C_REG_FIB0_CFG08    0x6208
-
-#define    RTL8367C_REG_FIB0_CFG09    0x6209
-
-#define    RTL8367C_REG_FIB0_CFG10    0x620a
-
-#define    RTL8367C_REG_FIB0_CFG11    0x620b
-
-#define    RTL8367C_REG_FIB0_CFG12    0x620c
-
-#define    RTL8367C_REG_FIB0_CFG13    0x620d
-#define    RTL8367C_FIB0_CFG13_INDR_FUNC_OFFSET    14
-#define    RTL8367C_FIB0_CFG13_INDR_FUNC_MASK    0xC000
-#define    RTL8367C_FIB0_CFG13_DUMMY_OFFSET    5
-#define    RTL8367C_FIB0_CFG13_DUMMY_MASK    0x3FE0
-#define    RTL8367C_FIB0_CFG13_INDR_DEVAD_OFFSET    0
-#define    RTL8367C_FIB0_CFG13_INDR_DEVAD_MASK    0x1F
-
-#define    RTL8367C_REG_FIB0_CFG14    0x620e
-
-#define    RTL8367C_REG_FIB0_CFG15    0x620f
-
-#define    RTL8367C_REG_FIB1_CFG00    0x6210
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_RST_OFFSET    15
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_RST_MASK    0x8000
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_LPK_OFFSET    14
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_LPK_MASK    0x4000
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_SPD_RD_0_OFFSET    13
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_SPD_RD_0_MASK    0x2000
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_ANEN_OFFSET    12
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_ANEN_MASK    0x1000
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_PDOWN_OFFSET    11
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_PDOWN_MASK    0x800
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_ISO_OFFSET    10
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_ISO_MASK    0x400
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_RESTART_OFFSET    9
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_RESTART_MASK    0x200
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_FULLDUP_OFFSET    8
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_FULLDUP_MASK    0x100
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_SPD_RD_1_OFFSET    6
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_SPD_RD_1_MASK    0x40
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_FRCTX_OFFSET    5
-#define    RTL8367C_FIB1_CFG00_CFG_FIB_FRCTX_MASK    0x20
-
-#define    RTL8367C_REG_FIB1_CFG01    0x6211
-#define    RTL8367C_FIB1_CFG01_CAPBILITY_OFFSET    6
-#define    RTL8367C_FIB1_CFG01_CAPBILITY_MASK    0xFFC0
-#define    RTL8367C_FIB1_CFG01_AN_COMPLETE_OFFSET    5
-#define    RTL8367C_FIB1_CFG01_AN_COMPLETE_MASK    0x20
-#define    RTL8367C_FIB1_CFG01_R_FAULT_OFFSET    4
-#define    RTL8367C_FIB1_CFG01_R_FAULT_MASK    0x10
-#define    RTL8367C_FIB1_CFG01_NWAY_ABILITY_OFFSET    3
-#define    RTL8367C_FIB1_CFG01_NWAY_ABILITY_MASK    0x8
-#define    RTL8367C_FIB1_CFG01_LINK_STATUS_OFFSET    2
-#define    RTL8367C_FIB1_CFG01_LINK_STATUS_MASK    0x4
-#define    RTL8367C_FIB1_CFG01_JABBER_DETECT_OFFSET    1
-#define    RTL8367C_FIB1_CFG01_JABBER_DETECT_MASK    0x2
-#define    RTL8367C_FIB1_CFG01_EXTENDED_CAPBILITY_OFFSET    0
-#define    RTL8367C_FIB1_CFG01_EXTENDED_CAPBILITY_MASK    0x1
-
-#define    RTL8367C_REG_FIB1_CFG02    0x6212
-
-#define    RTL8367C_REG_FIB1_CFG03    0x6213
-#define    RTL8367C_FIB1_CFG03_REALTEK_OUI5_0_OFFSET    10
-#define    RTL8367C_FIB1_CFG03_REALTEK_OUI5_0_MASK    0xFC00
-#define    RTL8367C_FIB1_CFG03_MODEL_NO_OFFSET    4
-#define    RTL8367C_FIB1_CFG03_MODEL_NO_MASK    0x3F0
-#define    RTL8367C_FIB1_CFG03_REVISION_NO_OFFSET    0
-#define    RTL8367C_FIB1_CFG03_REVISION_NO_MASK    0xF
-
-#define    RTL8367C_REG_FIB1_CFG04    0x6214
-
-#define    RTL8367C_REG_FIB1_CFG05    0x6215
-
-#define    RTL8367C_REG_FIB1_CFG06    0x6216
-#define    RTL8367C_FIB1_CFG06_FIB_NP_EN_OFFSET    2
-#define    RTL8367C_FIB1_CFG06_FIB_NP_EN_MASK    0x4
-#define    RTL8367C_FIB1_CFG06_RXPAGE_OFFSET    1
-#define    RTL8367C_FIB1_CFG06_RXPAGE_MASK    0x2
-
-#define    RTL8367C_REG_FIB1_CFG07    0x6217
-
-#define    RTL8367C_REG_FIB1_CFG08    0x6218
-
-#define    RTL8367C_REG_FIB1_CFG09    0x6219
-
-#define    RTL8367C_REG_FIB1_CFG10    0x621a
-
-#define    RTL8367C_REG_FIB1_CFG11    0x621b
-
-#define    RTL8367C_REG_FIB1_CFG12    0x621c
-
-#define    RTL8367C_REG_FIB1_CFG13    0x621d
-#define    RTL8367C_FIB1_CFG13_INDR_FUNC_OFFSET    14
-#define    RTL8367C_FIB1_CFG13_INDR_FUNC_MASK    0xC000
-#define    RTL8367C_FIB1_CFG13_DUMMY_OFFSET    5
-#define    RTL8367C_FIB1_CFG13_DUMMY_MASK    0x3FE0
-#define    RTL8367C_FIB1_CFG13_INDR_DEVAD_OFFSET    0
-#define    RTL8367C_FIB1_CFG13_INDR_DEVAD_MASK    0x1F
-
-#define    RTL8367C_REG_FIB1_CFG14    0x621e
-
-#define    RTL8367C_REG_FIB1_CFG15    0x621f
-
-/* (16'h6400)timer_1588 */
-
-#define    RTL8367C_REG_PTP_TIME_NSEC_L_NSEC    0x6400
-
-#define    RTL8367C_REG_PTP_TIME_NSEC_H_NSEC    0x6401
-#define    RTL8367C_PTP_TIME_NSEC_H_EXEC_OFFSET    15
-#define    RTL8367C_PTP_TIME_NSEC_H_EXEC_MASK    0x8000
-#define    RTL8367C_PTP_TIME_NSEC_H_CMD_OFFSET    12
-#define    RTL8367C_PTP_TIME_NSEC_H_CMD_MASK    0x3000
-#define    RTL8367C_PTP_TIME_NSEC_H_NSEC_OFFSET    0
-#define    RTL8367C_PTP_TIME_NSEC_H_NSEC_MASK    0x7FF
-
-#define    RTL8367C_REG_PTP_TIME_SEC_L_SEC    0x6402
-
-#define    RTL8367C_REG_PTP_TIME_SEC_H_SEC    0x6403
-
-#define    RTL8367C_REG_PTP_TIME_CFG    0x6404
-#define    RTL8367C_CFG_TIMER_EN_FRC_OFFSET    2
-#define    RTL8367C_CFG_TIMER_EN_FRC_MASK    0x4
-#define    RTL8367C_CFG_TIMER_1588_EN_OFFSET    1
-#define    RTL8367C_CFG_TIMER_1588_EN_MASK    0x2
-#define    RTL8367C_CFG_CLK_SRC_OFFSET    0
-#define    RTL8367C_CFG_CLK_SRC_MASK    0x1
-
-#define    RTL8367C_REG_OTAG_TPID    0x6405
-
-#define    RTL8367C_REG_ITAG_TPID    0x6406
-
-#define    RTL8367C_REG_MAC_ADDR_L    0x6407
-
-#define    RTL8367C_REG_MAC_ADDR_M    0x6408
-
-#define    RTL8367C_REG_MAC_ADDR_H    0x6409
-
-#define    RTL8367C_REG_PTP_TIME_NSEC_L_NSEC_RD    0x640a
-
-#define    RTL8367C_REG_PTP_TIME_NSEC_H_NSEC_RD    0x640b
-#define    RTL8367C_PTP_TIME_NSEC_H_NSEC_RD_OFFSET    0
-#define    RTL8367C_PTP_TIME_NSEC_H_NSEC_RD_MASK    0x7FF
-
-#define    RTL8367C_REG_PTP_TIME_SEC_L_SEC_RD    0x640c
-
-#define    RTL8367C_REG_PTP_TIME_SEC_H_SEC_RD    0x640d
-
-#define    RTL8367C_REG_PTP_TIME_CFG2    0x640e
-#define    RTL8367C_CFG_EN_OFFLOAD_OFFSET    9
-#define    RTL8367C_CFG_EN_OFFLOAD_MASK    0x200
-#define    RTL8367C_CFG_SAVE_OFF_TS_OFFSET    8
-#define    RTL8367C_CFG_SAVE_OFF_TS_MASK    0x100
-#define    RTL8367C_CFG_IMR_OFFSET    0
-#define    RTL8367C_CFG_IMR_MASK    0xFF
-
-#define    RTL8367C_REG_PTP_INTERRUPT_CFG    0x640f
-#define    RTL8367C_P9_INTERRUPT_OFFSET    9
-#define    RTL8367C_P9_INTERRUPT_MASK    0x200
-#define    RTL8367C_P8_INTERRUPT_OFFSET    8
-#define    RTL8367C_P8_INTERRUPT_MASK    0x100
-#define    RTL8367C_P7_INTERRUPT_OFFSET    7
-#define    RTL8367C_P7_INTERRUPT_MASK    0x80
-#define    RTL8367C_P6_INTERRUPT_OFFSET    6
-#define    RTL8367C_P6_INTERRUPT_MASK    0x40
-#define    RTL8367C_P5_INTERRUPT_OFFSET    5
-#define    RTL8367C_P5_INTERRUPT_MASK    0x20
-#define    RTL8367C_P4_INTERRUPT_OFFSET    4
-#define    RTL8367C_P4_INTERRUPT_MASK    0x10
-#define    RTL8367C_P3_INTERRUPT_OFFSET    3
-#define    RTL8367C_P3_INTERRUPT_MASK    0x8
-#define    RTL8367C_P2_INTERRUPT_OFFSET    2
-#define    RTL8367C_P2_INTERRUPT_MASK    0x4
-#define    RTL8367C_P1_INTERRUPT_OFFSET    1
-#define    RTL8367C_P1_INTERRUPT_MASK    0x2
-#define    RTL8367C_P0_INTERRUPT_OFFSET    0
-#define    RTL8367C_P0_INTERRUPT_MASK    0x1
-
-#define    RTL8367C_REG_P0_TX_SYNC_SEQ_ID    0x6410
-
-#define    RTL8367C_REG_P0_TX_DELAY_REQ_SEQ_ID    0x6411
-
-#define    RTL8367C_REG_P0_TX_PDELAY_REQ_SEQ_ID    0x6412
-
-#define    RTL8367C_REG_P0_TX_PDELAY_RESP_SEQ_ID    0x6413
-
-#define    RTL8367C_REG_P0_RX_SYNC_SEQ_ID    0x6414
-
-#define    RTL8367C_REG_P0_RX_DELAY_REQ_SEQ_ID    0x6415
-
-#define    RTL8367C_REG_P0_RX_PDELAY_REQ_SEQ_ID    0x6416
-
-#define    RTL8367C_REG_P0_RX_PDELAY_RESP_SEQ_ID    0x6417
-
-#define    RTL8367C_REG_P0_PORT_NSEC_15_0    0x6418
-
-#define    RTL8367C_REG_P0_PORT_NSEC_26_16    0x6419
-#define    RTL8367C_P0_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P0_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P0_PORT_SEC_15_0    0x641a
-
-#define    RTL8367C_REG_P0_PORT_SEC_31_16    0x641b
-
-#define    RTL8367C_REG_P0_EAV_CFG    0x641c
-#define    RTL8367C_P0_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P0_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P0_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P0_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P0_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P0_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P0_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P0_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P0_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P0_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P0_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P0_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P0_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P0_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P0_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P0_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P0_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P0_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P1_TX_SYNC_SEQ_ID    0x6420
-
-#define    RTL8367C_REG_P1_TX_DELAY_REQ_SEQ_ID    0x6421
-
-#define    RTL8367C_REG_P1_TX_PDELAY_REQ_SEQ_ID    0x6422
-
-#define    RTL8367C_REG_P1_TX_PDELAY_RESP_SEQ_ID    0x6423
-
-#define    RTL8367C_REG_P1_RX_SYNC_SEQ_ID    0x6424
-
-#define    RTL8367C_REG_P1_RX_DELAY_REQ_SEQ_ID    0x6425
-
-#define    RTL8367C_REG_P1_RX_PDELAY_REQ_SEQ_ID    0x6426
-
-#define    RTL8367C_REG_P1_RX_PDELAY_RESP_SEQ_ID    0x6427
-
-#define    RTL8367C_REG_P1_PORT_NSEC_15_0    0x6428
-
-#define    RTL8367C_REG_P1_PORT_NSEC_26_16    0x6429
-#define    RTL8367C_P1_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P1_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P1_PORT_SEC_15_0    0x642a
-
-#define    RTL8367C_REG_P1_PORT_SEC_31_16    0x642b
-
-#define    RTL8367C_REG_P1_EAV_CFG    0x642c
-#define    RTL8367C_P1_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P1_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P1_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P1_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P1_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P1_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P1_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P1_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P1_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P1_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P1_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P1_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P1_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P1_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P1_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P1_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P1_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P1_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P2_TX_SYNC_SEQ_ID    0x6430
-
-#define    RTL8367C_REG_P2_TX_DELAY_REQ_SEQ_ID    0x6431
-
-#define    RTL8367C_REG_P2_TX_PDELAY_REQ_SEQ_ID    0x6432
-
-#define    RTL8367C_REG_P2_TX_PDELAY_RESP_SEQ_ID    0x6433
-
-#define    RTL8367C_REG_P2_RX_SYNC_SEQ_ID    0x6434
-
-#define    RTL8367C_REG_P2_RX_DELAY_REQ_SEQ_ID    0x6435
-
-#define    RTL8367C_REG_P2_RX_PDELAY_REQ_SEQ_ID    0x6436
-
-#define    RTL8367C_REG_P2_RX_PDELAY_RESP_SEQ_ID    0x6437
-
-#define    RTL8367C_REG_P2_PORT_NSEC_15_0    0x6438
-
-#define    RTL8367C_REG_P2_PORT_NSEC_26_16    0x6439
-#define    RTL8367C_P2_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P2_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P2_PORT_SEC_15_0    0x643a
-
-#define    RTL8367C_REG_P2_PORT_SEC_31_16    0x643b
-
-#define    RTL8367C_REG_P2_EAV_CFG    0x643c
-#define    RTL8367C_P2_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P2_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P2_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P2_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P2_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P2_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P2_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P2_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P2_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P2_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P2_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P2_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P2_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P2_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P2_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P2_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P2_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P2_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P3_TX_SYNC_SEQ_ID    0x6440
-
-#define    RTL8367C_REG_P3_TX_DELAY_REQ_SEQ_ID    0x6441
-
-#define    RTL8367C_REG_P3_TX_PDELAY_REQ_SEQ_ID    0x6442
-
-#define    RTL8367C_REG_P3_TX_PDELAY_RESP_SEQ_ID    0x6443
-
-#define    RTL8367C_REG_P3_RX_SYNC_SEQ_ID    0x6444
-
-#define    RTL8367C_REG_P3_RX_DELAY_REQ_SEQ_ID    0x6445
-
-#define    RTL8367C_REG_P3_RX_PDELAY_REQ_SEQ_ID    0x6446
-
-#define    RTL8367C_REG_P3_RX_PDELAY_RESP_SEQ_ID    0x6447
-
-#define    RTL8367C_REG_P3_PORT_NSEC_15_0    0x6448
-
-#define    RTL8367C_REG_P3_PORT_NSEC_26_16    0x6449
-#define    RTL8367C_P3_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P3_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P3_PORT_SEC_15_0    0x644a
-
-#define    RTL8367C_REG_P3_PORT_SEC_31_16    0x644b
-
-#define    RTL8367C_REG_P3_EAV_CFG    0x644c
-#define    RTL8367C_P3_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P3_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P3_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P3_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P3_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P3_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P3_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P3_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P3_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P3_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P3_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P3_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P3_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P3_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P3_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P3_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P3_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P3_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P4_TX_SYNC_SEQ_ID    0x6450
-
-#define    RTL8367C_REG_P4_TX_DELAY_REQ_SEQ_ID    0x6451
-
-#define    RTL8367C_REG_P4_TX_PDELAY_REQ_SEQ_ID    0x6452
-
-#define    RTL8367C_REG_P4_TX_PDELAY_RESP_SEQ_ID    0x6453
-
-#define    RTL8367C_REG_P4_RX_SYNC_SEQ_ID    0x6454
-
-#define    RTL8367C_REG_P4_RX_DELAY_REQ_SEQ_ID    0x6455
-
-#define    RTL8367C_REG_P4_RX_PDELAY_REQ_SEQ_ID    0x6456
-
-#define    RTL8367C_REG_P4_RX_PDELAY_RESP_SEQ_ID    0x6457
-
-#define    RTL8367C_REG_P4_PORT_NSEC_15_0    0x6458
-
-#define    RTL8367C_REG_P4_PORT_NSEC_26_16    0x6459
-#define    RTL8367C_P4_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P4_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P4_PORT_SEC_15_0    0x645a
-
-#define    RTL8367C_REG_P4_PORT_SEC_31_16    0x645b
-
-#define    RTL8367C_REG_P4_EAV_CFG    0x645c
-#define    RTL8367C_P4_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P4_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P4_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P4_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P4_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P4_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P4_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P4_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P4_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P4_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P4_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P4_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P4_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P4_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P4_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P4_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P4_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P4_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P6_TX_SYNC_SEQ_ID    0x6460
-
-#define    RTL8367C_REG_P6_TX_DELAY_REQ_SEQ_ID    0x6461
-
-#define    RTL8367C_REG_P6_TX_PDELAY_REQ_SEQ_ID    0x6462
-
-#define    RTL8367C_REG_P6_TX_PDELAY_RESP_SEQ_ID    0x6463
-
-#define    RTL8367C_REG_P6_RX_SYNC_SEQ_ID    0x6464
-
-#define    RTL8367C_REG_P6_RX_DELAY_REQ_SEQ_ID    0x6465
-
-#define    RTL8367C_REG_P6_RX_PDELAY_REQ_SEQ_ID    0x6466
-
-#define    RTL8367C_REG_P6_RX_PDELAY_RESP_SEQ_ID    0x6467
-
-#define    RTL8367C_REG_P6_PORT_NSEC_15_0    0x6468
-
-#define    RTL8367C_REG_P6_PORT_NSEC_26_16    0x6469
-#define    RTL8367C_P6_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P6_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P6_PORT_SEC_15_0    0x646a
-
-#define    RTL8367C_REG_P6_PORT_SEC_31_16    0x646b
-
-#define    RTL8367C_REG_P6_EAV_CFG    0x646c
-#define    RTL8367C_P6_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P6_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P6_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P6_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P6_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P6_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P6_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P6_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P6_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P6_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P6_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P6_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P6_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P6_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P6_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P6_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P6_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P6_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P7_TX_SYNC_SEQ_ID    0x6470
-
-#define    RTL8367C_REG_P7_TX_DELAY_REQ_SEQ_ID    0x6471
-
-#define    RTL8367C_REG_P7_TX_PDELAY_REQ_SEQ_ID    0x6472
-
-#define    RTL8367C_REG_P7_TX_PDELAY_RESP_SEQ_ID    0x6473
-
-#define    RTL8367C_REG_P7_RX_SYNC_SEQ_ID    0x6474
-
-#define    RTL8367C_REG_P7_RX_DELAY_REQ_SEQ_ID    0x6475
-
-#define    RTL8367C_REG_P7_RX_PDELAY_REQ_SEQ_ID    0x6476
-
-#define    RTL8367C_REG_P7_RX_PDELAY_RESP_SEQ_ID    0x6477
-
-#define    RTL8367C_REG_P7_PORT_NSEC_15_0    0x6478
-
-#define    RTL8367C_REG_P7_PORT_NSEC_26_16    0x6479
-#define    RTL8367C_P7_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P7_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P7_PORT_SEC_15_0    0x647a
-
-#define    RTL8367C_REG_P7_PORT_SEC_31_16    0x647b
-
-#define    RTL8367C_REG_P7_EAV_CFG    0x647c
-#define    RTL8367C_P7_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P7_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P7_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P7_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P7_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P7_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P7_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P7_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P7_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P7_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P7_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P7_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P7_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P7_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P7_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P7_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P7_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P7_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P5_TX_SYNC_SEQ_ID    0x6480
-
-#define    RTL8367C_REG_P5_TX_DELAY_REQ_SEQ_ID    0x6481
-
-#define    RTL8367C_REG_P5_TX_PDELAY_REQ_SEQ_ID    0x6482
-
-#define    RTL8367C_REG_P5_TX_PDELAY_RESP_SEQ_ID    0x6483
-
-#define    RTL8367C_REG_P5_RX_SYNC_SEQ_ID    0x6484
-
-#define    RTL8367C_REG_P5_RX_DELAY_REQ_SEQ_ID    0x6485
-
-#define    RTL8367C_REG_P5_RX_PDELAY_REQ_SEQ_ID    0x6486
-
-#define    RTL8367C_REG_P5_RX_PDELAY_RESP_SEQ_ID    0x6487
-
-#define    RTL8367C_REG_P5_PORT_NSEC_15_0    0x6488
-
-#define    RTL8367C_REG_P5_PORT_NSEC_26_16    0x6489
-#define    RTL8367C_P5_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P5_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P5_PORT_SEC_15_0    0x648a
-
-#define    RTL8367C_REG_P5_PORT_SEC_31_16    0x648b
-
-#define    RTL8367C_REG_P5_EAV_CFG    0x648c
-#define    RTL8367C_P5_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P5_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P5_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P5_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P5_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P5_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P5_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P5_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P5_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P5_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P5_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P5_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P5_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P5_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P5_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P5_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P5_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P5_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P8_TX_SYNC_SEQ_ID    0x6490
-
-#define    RTL8367C_REG_P8_TX_DELAY_REQ_SEQ_ID    0x6491
-
-#define    RTL8367C_REG_P8_TX_PDELAY_REQ_SEQ_ID    0x6492
-
-#define    RTL8367C_REG_P8_TX_PDELAY_RESP_SEQ_ID    0x6493
-
-#define    RTL8367C_REG_P8_RX_SYNC_SEQ_ID    0x6494
-
-#define    RTL8367C_REG_P8_RX_DELAY_REQ_SEQ_ID    0x6495
-
-#define    RTL8367C_REG_P8_RX_PDELAY_REQ_SEQ_ID    0x6496
-
-#define    RTL8367C_REG_P8_RX_PDELAY_RESP_SEQ_ID    0x6497
-
-#define    RTL8367C_REG_P8_PORT_NSEC_15_0    0x6498
-
-#define    RTL8367C_REG_P8_PORT_NSEC_26_16    0x6499
-#define    RTL8367C_P8_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P8_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P8_PORT_SEC_15_0    0x649a
-
-#define    RTL8367C_REG_P8_PORT_SEC_31_16    0x649b
-
-#define    RTL8367C_REG_P8_EAV_CFG    0x649c
-#define    RTL8367C_P8_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P8_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P8_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P8_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P8_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P8_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P8_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P8_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P8_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P8_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P8_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P8_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P8_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P8_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P8_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P8_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P8_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P8_EAV_CFG_TX_SYNC_MASK    0x1
-
-#define    RTL8367C_REG_P9_TX_SYNC_SEQ_ID    0x64a0
-
-#define    RTL8367C_REG_P9_TX_DELAY_REQ_SEQ_ID    0x64a1
-
-#define    RTL8367C_REG_P9_TX_PDELAY_REQ_SEQ_ID    0x64a2
-
-#define    RTL8367C_REG_P9_TX_PDELAY_RESP_SEQ_ID    0x64a3
-
-#define    RTL8367C_REG_P9_RX_SYNC_SEQ_ID    0x64a4
-
-#define    RTL8367C_REG_P9_RX_DELAY_REQ_SEQ_ID    0x64a5
-
-#define    RTL8367C_REG_P9_RX_PDELAY_REQ_SEQ_ID    0x64a6
-
-#define    RTL8367C_REG_P9_RX_PDELAY_RESP_SEQ_ID    0x64a7
-
-#define    RTL8367C_REG_P9_PORT_NSEC_15_0    0x64a8
-
-#define    RTL8367C_REG_P9_PORT_NSEC_26_16    0x64a9
-#define    RTL8367C_P9_PORT_NSEC_26_16_OFFSET    0
-#define    RTL8367C_P9_PORT_NSEC_26_16_MASK    0x7FF
-
-#define    RTL8367C_REG_P9_PORT_SEC_15_0    0x64aa
-
-#define    RTL8367C_REG_P9_PORT_SEC_31_16    0x64ab
-
-#define    RTL8367C_REG_P9_EAV_CFG    0x64ac
-#define    RTL8367C_P9_EAV_CFG_PTP_PHY_EN_EN_OFFSET    8
-#define    RTL8367C_P9_EAV_CFG_PTP_PHY_EN_EN_MASK    0x100
-#define    RTL8367C_P9_EAV_CFG_RX_PDELAY_RESP_OFFSET    7
-#define    RTL8367C_P9_EAV_CFG_RX_PDELAY_RESP_MASK    0x80
-#define    RTL8367C_P9_EAV_CFG_RX_PDELAY_REQ_OFFSET    6
-#define    RTL8367C_P9_EAV_CFG_RX_PDELAY_REQ_MASK    0x40
-#define    RTL8367C_P9_EAV_CFG_RX_DELAY_REQ_OFFSET    5
-#define    RTL8367C_P9_EAV_CFG_RX_DELAY_REQ_MASK    0x20
-#define    RTL8367C_P9_EAV_CFG_RX_SYNC_OFFSET    4
-#define    RTL8367C_P9_EAV_CFG_RX_SYNC_MASK    0x10
-#define    RTL8367C_P9_EAV_CFG_TX_PDELAY_RESP_OFFSET    3
-#define    RTL8367C_P9_EAV_CFG_TX_PDELAY_RESP_MASK    0x8
-#define    RTL8367C_P9_EAV_CFG_TX_PDELAY_REQ_OFFSET    2
-#define    RTL8367C_P9_EAV_CFG_TX_PDELAY_REQ_MASK    0x4
-#define    RTL8367C_P9_EAV_CFG_TX_DELAY_REQ_OFFSET    1
-#define    RTL8367C_P9_EAV_CFG_TX_DELAY_REQ_MASK    0x2
-#define    RTL8367C_P9_EAV_CFG_TX_SYNC_OFFSET    0
-#define    RTL8367C_P9_EAV_CFG_TX_SYNC_MASK    0x1
-
-/* (16'h6600)sds_indacs_reg */
-
-#define    RTL8367C_REG_SDS_INDACS_CMD    0x6600
-#define    RTL8367C_SDS_CMD_BUSY_OFFSET    8
-#define    RTL8367C_SDS_CMD_BUSY_MASK    0x100
-#define    RTL8367C_SDS_CMD_OFFSET    7
-#define    RTL8367C_SDS_CMD_MASK    0x80
-#define    RTL8367C_SDS_RWOP_OFFSET    6
-#define    RTL8367C_SDS_RWOP_MASK    0x40
-#define    RTL8367C_SDS_INDEX_OFFSET    0
-#define    RTL8367C_SDS_INDEX_MASK    0x3F
-
-#define    RTL8367C_REG_SDS_INDACS_ADR    0x6601
-#define    RTL8367C_SDS_PAGE_OFFSET    5
-#define    RTL8367C_SDS_PAGE_MASK    0x7E0
-#define    RTL8367C_SDS_REGAD_OFFSET    0
-#define    RTL8367C_SDS_REGAD_MASK    0x1F
-
-#define    RTL8367C_REG_SDS_INDACS_DATA    0x6602
-
-
-#endif /*#ifndef _RTL8367C_REG_H_*/
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/smi.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/smi.h
deleted file mode 100644
index b77d760711..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/smi.h
+++ /dev/null
@@ -1,54 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367C switch low-level function for access register
- * Feature : SMI related functions
- *
- */
-
-#ifndef __SMI_H__
-#define __SMI_H__
-
-#include <rtk_types.h>
-#include "rtk_error.h"
-
-#define MDC_MDIO_CTRL0_REG          31
-#define MDC_MDIO_START_REG          29
-#define MDC_MDIO_CTRL1_REG          21
-#define MDC_MDIO_ADDRESS_REG        23
-#define MDC_MDIO_DATA_WRITE_REG     24
-#define MDC_MDIO_DATA_READ_REG      25
-#define MDC_MDIO_PREAMBLE_LEN       32
-
-#define MDC_MDIO_START_OP          0xFFFF
-#define MDC_MDIO_ADDR_OP           0x000E
-#define MDC_MDIO_READ_OP           0x0001
-#define MDC_MDIO_WRITE_OP          0x0003
-
-#define SPI_READ_OP                 0x3
-#define SPI_WRITE_OP                0x2
-#define SPI_READ_OP_LEN             0x8
-#define SPI_WRITE_OP_LEN            0x8
-#define SPI_REG_LEN                 16
-#define SPI_DATA_LEN                16
-
-#define GPIO_DIR_IN                 1
-#define GPIO_DIR_OUT                0
-
-#define ack_timer                   5
-
-#define DELAY                        10000
-#define CLK_DURATION(clk)            { int i; for(i=0; i<clk; i++); }
-
-rtk_int32 smi_read(rtk_uint32 mAddrs, rtk_uint32 *rData);
-rtk_int32 smi_write(rtk_uint32 mAddrs, rtk_uint32 rData);
-
-#endif /* __SMI_H__ */
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/stat.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/stat.h
deleted file mode 100644
index a7357633a1..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/stat.h
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes MIB module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_STAT_H__
-#define __RTK_API_STAT_H__
-
-/*
- * Data Type Declaration
- */
-typedef rtk_u_long_t rtk_stat_counter_t;
-
-/* global statistic counter structure */
-typedef struct rtk_stat_global_cntr_s
-{
-    rtk_uint64 dot1dTpLearnedEntryDiscards;
-}rtk_stat_global_cntr_t;
-
-typedef enum rtk_stat_global_type_e
-{
-    DOT1D_TP_LEARNED_ENTRY_DISCARDS_INDEX = 58,
-    MIB_GLOBAL_CNTR_END
-}rtk_stat_global_type_t;
-
-/* port statistic counter structure */
-typedef struct rtk_stat_port_cntr_s
-{
-    rtk_uint64 ifInOctets;
-    rtk_uint32 dot3StatsFCSErrors;
-    rtk_uint32 dot3StatsSymbolErrors;
-    rtk_uint32 dot3InPauseFrames;
-    rtk_uint32 dot3ControlInUnknownOpcodes;
-    rtk_uint32 etherStatsFragments;
-    rtk_uint32 etherStatsJabbers;
-    rtk_uint32 ifInUcastPkts;
-    rtk_uint32 etherStatsDropEvents;
-    rtk_uint64 etherStatsOctets;
-    rtk_uint32 etherStatsUndersizePkts;
-    rtk_uint32 etherStatsOversizePkts;
-    rtk_uint32 etherStatsPkts64Octets;
-    rtk_uint32 etherStatsPkts65to127Octets;
-    rtk_uint32 etherStatsPkts128to255Octets;
-    rtk_uint32 etherStatsPkts256to511Octets;
-    rtk_uint32 etherStatsPkts512to1023Octets;
-    rtk_uint32 etherStatsPkts1024toMaxOctets;
-    rtk_uint32 etherStatsMcastPkts;
-    rtk_uint32 etherStatsBcastPkts;
-    rtk_uint64 ifOutOctets;
-    rtk_uint32 dot3StatsSingleCollisionFrames;
-    rtk_uint32 dot3StatsMultipleCollisionFrames;
-    rtk_uint32 dot3StatsDeferredTransmissions;
-    rtk_uint32 dot3StatsLateCollisions;
-    rtk_uint32 etherStatsCollisions;
-    rtk_uint32 dot3StatsExcessiveCollisions;
-    rtk_uint32 dot3OutPauseFrames;
-    rtk_uint32 dot1dBasePortDelayExceededDiscards;
-    rtk_uint32 dot1dTpPortInDiscards;
-    rtk_uint32 ifOutUcastPkts;
-    rtk_uint32 ifOutMulticastPkts;
-    rtk_uint32 ifOutBrocastPkts;
-    rtk_uint32 outOampduPkts;
-    rtk_uint32 inOampduPkts;
-    rtk_uint32 pktgenPkts;
-    rtk_uint32 inMldChecksumError;
-    rtk_uint32 inIgmpChecksumError;
-    rtk_uint32 inMldSpecificQuery;
-    rtk_uint32 inMldGeneralQuery;
-    rtk_uint32 inIgmpSpecificQuery;
-    rtk_uint32 inIgmpGeneralQuery;
-    rtk_uint32 inMldLeaves;
-    rtk_uint32 inIgmpLeaves;
-    rtk_uint32 inIgmpJoinsSuccess;
-    rtk_uint32 inIgmpJoinsFail;
-    rtk_uint32 inMldJoinsSuccess;
-    rtk_uint32 inMldJoinsFail;
-    rtk_uint32 inReportSuppressionDrop;
-    rtk_uint32 inLeaveSuppressionDrop;
-    rtk_uint32 outIgmpReports;
-    rtk_uint32 outIgmpLeaves;
-    rtk_uint32 outIgmpGeneralQuery;
-    rtk_uint32 outIgmpSpecificQuery;
-    rtk_uint32 outMldReports;
-    rtk_uint32 outMldLeaves;
-    rtk_uint32 outMldGeneralQuery;
-    rtk_uint32 outMldSpecificQuery;
-    rtk_uint32 inKnownMulticastPkts;
-    rtk_uint32 ifInMulticastPkts;
-    rtk_uint32 ifInBroadcastPkts;
-    rtk_uint32 ifOutDiscards;
-}rtk_stat_port_cntr_t;
-
-/* port statistic counter index */
-typedef enum rtk_stat_port_type_e
-{
-    STAT_IfInOctets = 0,
-    STAT_Dot3StatsFCSErrors,
-    STAT_Dot3StatsSymbolErrors,
-    STAT_Dot3InPauseFrames,
-    STAT_Dot3ControlInUnknownOpcodes,
-    STAT_EtherStatsFragments,
-    STAT_EtherStatsJabbers,
-    STAT_IfInUcastPkts,
-    STAT_EtherStatsDropEvents,
-    STAT_EtherStatsOctets,
-    STAT_EtherStatsUnderSizePkts,
-    STAT_EtherOversizeStats,
-    STAT_EtherStatsPkts64Octets,
-    STAT_EtherStatsPkts65to127Octets,
-    STAT_EtherStatsPkts128to255Octets,
-    STAT_EtherStatsPkts256to511Octets,
-    STAT_EtherStatsPkts512to1023Octets,
-    STAT_EtherStatsPkts1024to1518Octets,
-    STAT_EtherStatsMulticastPkts,
-    STAT_EtherStatsBroadcastPkts,
-    STAT_IfOutOctets,
-    STAT_Dot3StatsSingleCollisionFrames,
-    STAT_Dot3StatsMultipleCollisionFrames,
-    STAT_Dot3StatsDeferredTransmissions,
-    STAT_Dot3StatsLateCollisions,
-    STAT_EtherStatsCollisions,
-    STAT_Dot3StatsExcessiveCollisions,
-    STAT_Dot3OutPauseFrames,
-    STAT_Dot1dBasePortDelayExceededDiscards,
-    STAT_Dot1dTpPortInDiscards,
-    STAT_IfOutUcastPkts,
-    STAT_IfOutMulticastPkts,
-    STAT_IfOutBroadcastPkts,
-    STAT_OutOampduPkts,
-    STAT_InOampduPkts,
-    STAT_PktgenPkts,
-    STAT_InMldChecksumError,
-    STAT_InIgmpChecksumError,
-    STAT_InMldSpecificQuery,
-    STAT_InMldGeneralQuery,
-    STAT_InIgmpSpecificQuery,
-    STAT_InIgmpGeneralQuery,
-    STAT_InMldLeaves,
-    STAT_InIgmpInterfaceLeaves,
-    STAT_InIgmpJoinsSuccess,
-    STAT_InIgmpJoinsFail,
-    STAT_InMldJoinsSuccess,
-    STAT_InMldJoinsFail,
-    STAT_InReportSuppressionDrop,
-    STAT_InLeaveSuppressionDrop,
-    STAT_OutIgmpReports,
-    STAT_OutIgmpLeaves,
-    STAT_OutIgmpGeneralQuery,
-    STAT_OutIgmpSpecificQuery,
-    STAT_OutMldReports,
-    STAT_OutMldLeaves,
-    STAT_OutMldGeneralQuery,
-    STAT_OutMldSpecificQuery,
-    STAT_InKnownMulticastPkts,
-    STAT_IfInMulticastPkts,
-    STAT_IfInBroadcastPkts,
-    STAT_IfOutDiscards,
-    STAT_PORT_CNTR_END
-}rtk_stat_port_type_t;
-
-typedef enum rtk_logging_counter_mode_e
-{
-    LOGGING_MODE_32BIT = 0,
-    LOGGING_MODE_64BIT,
-    LOGGING_MODE_END
-}rtk_logging_counter_mode_t;
-
-typedef enum rtk_logging_counter_type_e
-{
-    LOGGING_TYPE_PACKET = 0,
-    LOGGING_TYPE_BYTE,
-    LOGGING_TYPE_END
-}rtk_logging_counter_type_t;
-
-typedef enum rtk_stat_lengthMode_e
-{
-    LENGTH_MODE_EXC_TAG = 0,
-    LENGTH_MODE_INC_TAG,
-    LENGTH_MODE_END
-}rtk_stat_lengthMode_t;
-
-
-
-/* Function Name:
- *      rtk_stat_global_reset
- * Description:
- *      Reset global MIB counter.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Reset MIB counter of ports. API will use global reset while port mask is all-ports.
- */
-extern rtk_api_ret_t rtk_stat_global_reset(void);
-
-/* Function Name:
- *      rtk_stat_port_reset
- * Description:
- *      Reset per port MIB counter by port.
- * Input:
- *      port - port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_stat_port_reset(rtk_port_t port);
-
-/* Function Name:
- *      rtk_stat_queueManage_reset
- * Description:
- *      Reset queue manage MIB counter.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_stat_queueManage_reset(void);
-
-/* Function Name:
- *      rtk_stat_global_get
- * Description:
- *      Get global MIB counter
- * Input:
- *      cntr_idx - global counter index.
- * Output:
- *      pCntr - global counter value.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get global MIB counter by index definition.
- */
-extern rtk_api_ret_t rtk_stat_global_get(rtk_stat_global_type_t cntr_idx, rtk_stat_counter_t *pCntr);
-
-/* Function Name:
- *      rtk_stat_global_getAll
- * Description:
- *      Get all global MIB counter
- * Input:
- *      None
- * Output:
- *      pGlobal_cntrs - global counter structure.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get all global MIB counter by index definition.
- */
-extern rtk_api_ret_t rtk_stat_global_getAll(rtk_stat_global_cntr_t *pGlobal_cntrs);
-
-/* Function Name:
- *      rtk_stat_port_get
- * Description:
- *      Get per port MIB counter by index
- * Input:
- *      port        - port id.
- *      cntr_idx    - port counter index.
- * Output:
- *      pCntr - MIB retrived counter.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Get per port MIB counter by index definition.
- */
-extern rtk_api_ret_t rtk_stat_port_get(rtk_port_t port, rtk_stat_port_type_t cntr_idx, rtk_stat_counter_t *pCntr);
-
-/* Function Name:
- *      rtk_stat_port_getAll
- * Description:
- *      Get all counters of one specified port in the specified device.
- * Input:
- *      port - port id.
- * Output:
- *      pPort_cntrs - buffer pointer of counter value.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get all MIB counters of one port.
- */
-extern rtk_api_ret_t rtk_stat_port_getAll(rtk_port_t port, rtk_stat_port_cntr_t *pPort_cntrs);
-
-/* Function Name:
- *      rtk_stat_logging_counterCfg_set
- * Description:
- *      Set the type and mode of Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. Should be even number only.(0,2,4,6,8.....30)
- *      mode    - 32 bits or 64 bits mode
- *      type    - Packet counter or byte counter
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Set the type and mode of Logging Counter.
- */
-extern rtk_api_ret_t rtk_stat_logging_counterCfg_set(rtk_uint32 idx, rtk_logging_counter_mode_t mode, rtk_logging_counter_type_t type);
-
-/* Function Name:
- *      rtk_stat_logging_counterCfg_get
- * Description:
- *      Get the type and mode of Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. Should be even number only.(0,2,4,6,8.....30)
- * Output:
- *      pMode   - 32 bits or 64 bits mode
- *      pType   - Packet counter or byte counter
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_NULL_POINTER - NULL Pointer
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get the type and mode of Logging Counter.
- */
-extern rtk_api_ret_t rtk_stat_logging_counterCfg_get(rtk_uint32 idx, rtk_logging_counter_mode_t *pMode, rtk_logging_counter_type_t *pType);
-
-/* Function Name:
- *      rtk_stat_logging_counter_reset
- * Description:
- *      Reset Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. (0~31)
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Reset Logging Counter.
- */
-extern rtk_api_ret_t rtk_stat_logging_counter_reset(rtk_uint32 idx);
-
-/* Function Name:
- *      rtk_stat_logging_counter_get
- * Description:
- *      Get Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. (0~31)
- * Output:
- *      pCnt    - Logging counter value
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Get Logging Counter.
- */
-extern rtk_api_ret_t rtk_stat_logging_counter_get(rtk_uint32 idx, rtk_uint32 *pCnt);
-
-/* Function Name:
- *      rtk_stat_lengthMode_set
- * Description:
- *      Set Legnth mode.
- * Input:
- *      txMode     - The length counting mode
- *      rxMode     - The length counting mode
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_INPUT        - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_stat_lengthMode_set(rtk_stat_lengthMode_t txMode, rtk_stat_lengthMode_t rxMode);
-
-/* Function Name:
- *      rtk_stat_lengthMode_get
- * Description:
- *      Get Legnth mode.
- * Input:
- *      None.
- * Output:
- *      pTxMode       - The length counting mode
- *      pRxMode       - The length counting mode
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_INPUT        - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- */
-extern rtk_api_ret_t rtk_stat_lengthMode_get(rtk_stat_lengthMode_t *pTxMode, rtk_stat_lengthMode_t *pRxMode);
-
-#endif /* __RTK_API_STAT_H__ */
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/storm.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/storm.h
deleted file mode 100644
index 55a50d750f..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/storm.h
+++ /dev/null
@@ -1,422 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes Storm module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_STORM_H__
-#define __RTK_API_STORM_H__
-
-#define STORM_UNUC_INDEX                            28
-#define STORM_UNMC_INDEX                            29
-#define STORM_MC_INDEX                              30
-#define STORM_BC_INDEX                              31
-
-typedef enum rtk_rate_storm_group_e
-{
-    STORM_GROUP_UNKNOWN_UNICAST = 0,
-    STORM_GROUP_UNKNOWN_MULTICAST,
-    STORM_GROUP_MULTICAST,
-    STORM_GROUP_BROADCAST,
-    STORM_GROUP_END
-} rtk_rate_storm_group_t;
-
-typedef enum rtk_storm_bypass_e
-{
-    BYPASS_BRG_GROUP = 0,
-    BYPASS_FD_PAUSE,
-    BYPASS_SP_MCAST,
-    BYPASS_1X_PAE,
-    BYPASS_UNDEF_BRG_04,
-    BYPASS_UNDEF_BRG_05,
-    BYPASS_UNDEF_BRG_06,
-    BYPASS_UNDEF_BRG_07,
-    BYPASS_PROVIDER_BRIDGE_GROUP_ADDRESS,
-    BYPASS_UNDEF_BRG_09,
-    BYPASS_UNDEF_BRG_0A,
-    BYPASS_UNDEF_BRG_0B,
-    BYPASS_UNDEF_BRG_0C,
-    BYPASS_PROVIDER_BRIDGE_GVRP_ADDRESS,
-    BYPASS_8021AB,
-    BYPASS_UNDEF_BRG_0F,
-    BYPASS_BRG_MNGEMENT,
-    BYPASS_UNDEFINED_11,
-    BYPASS_UNDEFINED_12,
-    BYPASS_UNDEFINED_13,
-    BYPASS_UNDEFINED_14,
-    BYPASS_UNDEFINED_15,
-    BYPASS_UNDEFINED_16,
-    BYPASS_UNDEFINED_17,
-    BYPASS_UNDEFINED_18,
-    BYPASS_UNDEFINED_19,
-    BYPASS_UNDEFINED_1A,
-    BYPASS_UNDEFINED_1B,
-    BYPASS_UNDEFINED_1C,
-    BYPASS_UNDEFINED_1D,
-    BYPASS_UNDEFINED_1E,
-    BYPASS_UNDEFINED_1F,
-    BYPASS_GMRP,
-    BYPASS_GVRP,
-    BYPASS_UNDEF_GARP_22,
-    BYPASS_UNDEF_GARP_23,
-    BYPASS_UNDEF_GARP_24,
-    BYPASS_UNDEF_GARP_25,
-    BYPASS_UNDEF_GARP_26,
-    BYPASS_UNDEF_GARP_27,
-    BYPASS_UNDEF_GARP_28,
-    BYPASS_UNDEF_GARP_29,
-    BYPASS_UNDEF_GARP_2A,
-    BYPASS_UNDEF_GARP_2B,
-    BYPASS_UNDEF_GARP_2C,
-    BYPASS_UNDEF_GARP_2D,
-    BYPASS_UNDEF_GARP_2E,
-    BYPASS_UNDEF_GARP_2F,
-    BYPASS_IGMP,
-    BYPASS_CDP,
-    BYPASS_CSSTP,
-    BYPASS_LLDP,
-    BYPASS_END,
-}rtk_storm_bypass_t;
-
-/* Function Name:
- *      rtk_rate_stormControlMeterIdx_set
- * Description:
- *      Set the storm control meter index.
- * Input:
- *      port       - port id
- *      storm_type - storm group type
- *      index       - storm control meter index.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID - Invalid port id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlMeterIdx_set(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_uint32 index);
-
-/* Function Name:
- *      rtk_rate_stormControlMeterIdx_get
- * Description:
- *      Get the storm control meter index.
- * Input:
- *      port       - port id
- *      storm_type - storm group type
- * Output:
- *      pIndex     - storm control meter index.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID - Invalid port id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlMeterIdx_get(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_uint32 *pIndex);
-
-/* Function Name:
- *      rtk_rate_stormControlPortEnable_set
- * Description:
- *      Set enable status of storm control on specified port.
- * Input:
- *      port       - port id
- *      stormType  - storm group type
- *      enable     - enable status of storm control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_PORT_ID           - invalid port id
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlPortEnable_set(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_rate_stormControlPortEnable_set
- * Description:
- *      Set enable status of storm control on specified port.
- * Input:
- *      port       - port id
- *      stormType  - storm group type
- * Output:
- *      pEnable     - enable status of storm control
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_PORT_ID           - invalid port id
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlPortEnable_get(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_storm_bypass_set
- * Description:
- *      Set bypass storm filter control configuration.
- * Input:
- *      type    - Bypass storm filter control type.
- *      enable  - Bypass status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid IFG parameter
- * Note:
- *
- *      This API can set per-port bypass stomr filter control frame type including RMA and igmp.
- *      The bypass frame type is as following:
- *      - BYPASS_BRG_GROUP,
- *      - BYPASS_FD_PAUSE,
- *      - BYPASS_SP_MCAST,
- *      - BYPASS_1X_PAE,
- *      - BYPASS_UNDEF_BRG_04,
- *      - BYPASS_UNDEF_BRG_05,
- *      - BYPASS_UNDEF_BRG_06,
- *      - BYPASS_UNDEF_BRG_07,
- *      - BYPASS_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - BYPASS_UNDEF_BRG_09,
- *      - BYPASS_UNDEF_BRG_0A,
- *      - BYPASS_UNDEF_BRG_0B,
- *      - BYPASS_UNDEF_BRG_0C,
- *      - BYPASS_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - BYPASS_8021AB,
- *      - BYPASS_UNDEF_BRG_0F,
- *      - BYPASS_BRG_MNGEMENT,
- *      - BYPASS_UNDEFINED_11,
- *      - BYPASS_UNDEFINED_12,
- *      - BYPASS_UNDEFINED_13,
- *      - BYPASS_UNDEFINED_14,
- *      - BYPASS_UNDEFINED_15,
- *      - BYPASS_UNDEFINED_16,
- *      - BYPASS_UNDEFINED_17,
- *      - BYPASS_UNDEFINED_18,
- *      - BYPASS_UNDEFINED_19,
- *      - BYPASS_UNDEFINED_1A,
- *      - BYPASS_UNDEFINED_1B,
- *      - BYPASS_UNDEFINED_1C,
- *      - BYPASS_UNDEFINED_1D,
- *      - BYPASS_UNDEFINED_1E,
- *      - BYPASS_UNDEFINED_1F,
- *      - BYPASS_GMRP,
- *      - BYPASS_GVRP,
- *      - BYPASS_UNDEF_GARP_22,
- *      - BYPASS_UNDEF_GARP_23,
- *      - BYPASS_UNDEF_GARP_24,
- *      - BYPASS_UNDEF_GARP_25,
- *      - BYPASS_UNDEF_GARP_26,
- *      - BYPASS_UNDEF_GARP_27,
- *      - BYPASS_UNDEF_GARP_28,
- *      - BYPASS_UNDEF_GARP_29,
- *      - BYPASS_UNDEF_GARP_2A,
- *      - BYPASS_UNDEF_GARP_2B,
- *      - BYPASS_UNDEF_GARP_2C,
- *      - BYPASS_UNDEF_GARP_2D,
- *      - BYPASS_UNDEF_GARP_2E,
- *      - BYPASS_UNDEF_GARP_2F,
- *      - BYPASS_IGMP.
- */
-extern rtk_api_ret_t rtk_storm_bypass_set(rtk_storm_bypass_t type, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_storm_bypass_get
- * Description:
- *      Get bypass storm filter control configuration.
- * Input:
- *      type - Bypass storm filter control type.
- * Output:
- *      pEnable - Bypass status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get per-port bypass stomr filter control frame type including RMA and igmp.
- *      The bypass frame type is as following:
- *      - BYPASS_BRG_GROUP,
- *      - BYPASS_FD_PAUSE,
- *      - BYPASS_SP_MCAST,
- *      - BYPASS_1X_PAE,
- *      - BYPASS_UNDEF_BRG_04,
- *      - BYPASS_UNDEF_BRG_05,
- *      - BYPASS_UNDEF_BRG_06,
- *      - BYPASS_UNDEF_BRG_07,
- *      - BYPASS_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - BYPASS_UNDEF_BRG_09,
- *      - BYPASS_UNDEF_BRG_0A,
- *      - BYPASS_UNDEF_BRG_0B,
- *      - BYPASS_UNDEF_BRG_0C,
- *      - BYPASS_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - BYPASS_8021AB,
- *      - BYPASS_UNDEF_BRG_0F,
- *      - BYPASS_BRG_MNGEMENT,
- *      - BYPASS_UNDEFINED_11,
- *      - BYPASS_UNDEFINED_12,
- *      - BYPASS_UNDEFINED_13,
- *      - BYPASS_UNDEFINED_14,
- *      - BYPASS_UNDEFINED_15,
- *      - BYPASS_UNDEFINED_16,
- *      - BYPASS_UNDEFINED_17,
- *      - BYPASS_UNDEFINED_18,
- *      - BYPASS_UNDEFINED_19,
- *      - BYPASS_UNDEFINED_1A,
- *      - BYPASS_UNDEFINED_1B,
- *      - BYPASS_UNDEFINED_1C,
- *      - BYPASS_UNDEFINED_1D,
- *      - BYPASS_UNDEFINED_1E,
- *      - BYPASS_UNDEFINED_1F,
- *      - BYPASS_GMRP,
- *      - BYPASS_GVRP,
- *      - BYPASS_UNDEF_GARP_22,
- *      - BYPASS_UNDEF_GARP_23,
- *      - BYPASS_UNDEF_GARP_24,
- *      - BYPASS_UNDEF_GARP_25,
- *      - BYPASS_UNDEF_GARP_26,
- *      - BYPASS_UNDEF_GARP_27,
- *      - BYPASS_UNDEF_GARP_28,
- *      - BYPASS_UNDEF_GARP_29,
- *      - BYPASS_UNDEF_GARP_2A,
- *      - BYPASS_UNDEF_GARP_2B,
- *      - BYPASS_UNDEF_GARP_2C,
- *      - BYPASS_UNDEF_GARP_2D,
- *      - BYPASS_UNDEF_GARP_2E,
- *      - BYPASS_UNDEF_GARP_2F,
- *      - BYPASS_IGMP.
- */
-extern rtk_api_ret_t rtk_storm_bypass_get(rtk_storm_bypass_t type, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_rate_stormControlExtPortmask_set
- * Description:
- *      Set externsion storm control port mask
- * Input:
- *      pPortmask  - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlExtPortmask_set(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_rate_stormControlExtPortmask_get
- * Description:
- *      Set externsion storm control port mask
- * Input:
- *      None
- * Output:
- *      pPortmask  - port mask
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlExtPortmask_get(rtk_portmask_t *pPortmask);
-
-/* Function Name:
- *      rtk_rate_stormControlExtEnable_set
- * Description:
- *      Set externsion storm control state
- * Input:
- *      stormType   - storm group type
- *      enable      - externsion storm control state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlExtEnable_set(rtk_rate_storm_group_t stormType, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_rate_stormControlExtEnable_get
- * Description:
- *      Get externsion storm control state
- * Input:
- *      stormType   - storm group type
- * Output:
- *      pEnable     - externsion storm control state
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlExtEnable_get(rtk_rate_storm_group_t stormType, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_rate_stormControlExtMeterIdx_set
- * Description:
- *      Set externsion storm control meter index
- * Input:
- *      stormType   - storm group type
- *      index       - externsion storm control state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlExtMeterIdx_set(rtk_rate_storm_group_t stormType, rtk_uint32 index);
-
-/* Function Name:
- *      rtk_rate_stormControlExtMeterIdx_get
- * Description:
- *      Get externsion storm control meter index
- * Input:
- *      stormType   - storm group type
- *      pIndex      - externsion storm control state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_rate_stormControlExtMeterIdx_get(rtk_rate_storm_group_t stormType, rtk_uint32 *pIndex);
-
-
-
-#endif /* __RTK_API_STORM_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/svlan.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/svlan.h
deleted file mode 100644
index bcdb02f41d..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/svlan.h
+++ /dev/null
@@ -1,896 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes SVLAN module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_SVLAN_H__
-#define __RTK_API_SVLAN_H__
-
-typedef rtk_uint32 rtk_svlan_index_t;
-
-typedef struct rtk_svlan_memberCfg_s{
-    rtk_uint32 svid;
-    rtk_portmask_t memberport;
-    rtk_portmask_t untagport;
-    rtk_uint32 fiden;
-    rtk_uint32 fid;
-    rtk_uint32 priority;
-    rtk_uint32 efiden;
-    rtk_uint32 efid;
-}rtk_svlan_memberCfg_t;
-
-typedef enum rtk_svlan_pri_ref_e
-{
-    REF_INTERNAL_PRI = 0,
-    REF_CTAG_PRI,
-    REF_SVLAN_PRI,
-    REF_PB_PRI,
-    REF_PRI_END
-} rtk_svlan_pri_ref_t;
-
-
-typedef rtk_uint32 rtk_svlan_tpid_t;
-
-typedef enum rtk_svlan_untag_action_e
-{
-    UNTAG_DROP = 0,
-    UNTAG_TRAP,
-    UNTAG_ASSIGN,
-    UNTAG_END
-} rtk_svlan_untag_action_t;
-
-typedef enum rtk_svlan_unmatch_action_e
-{
-    UNMATCH_DROP = 0,
-    UNMATCH_TRAP,
-    UNMATCH_ASSIGN,
-    UNMATCH_END
-} rtk_svlan_unmatch_action_t;
-
-typedef enum rtk_svlan_unassign_action_e
-{
-    UNASSIGN_PBSVID = 0,
-    UNASSIGN_TRAP,
-    UNASSIGN_END
-} rtk_svlan_unassign_action_t;
-
-
-typedef enum rtk_svlan_lookupType_e
-{
-    SVLAN_LOOKUP_S64MBRCGF  = 0,
-    SVLAN_LOOKUP_C4KVLAN,
-    SVLAN_LOOKUP_END,
-
-} rtk_svlan_lookupType_t;
-
-/* Function Name:
- *      rtk_svlan_init
- * Description:
- *      Initialize SVLAN Configuration
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Ether type of S-tag in 802.1ad is 0x88a8 and there are existed ether type 0x9100 and 0x9200 for Q-in-Q SLAN design.
- *      User can set mathced ether type as service provider supported protocol.
- */
-extern rtk_api_ret_t rtk_svlan_init(void);
-
-/* Function Name:
- *      rtk_svlan_servicePort_add
- * Description:
- *      Add one service port in the specified device
- * Input:
- *      port - Port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API is setting which port is connected to provider switch. All frames receiving from this port must
- *      contain accept SVID in S-tag field.
- */
-extern rtk_api_ret_t rtk_svlan_servicePort_add(rtk_port_t port);
-
-/* Function Name:
- *      rtk_svlan_servicePort_get
- * Description:
- *      Get service ports in the specified device.
- * Input:
- *      None
- * Output:
- *      pSvlan_portmask - pointer buffer of svlan ports.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      This API is setting which port is connected to provider switch. All frames receiving from this port must
- *      contain accept SVID in S-tag field.
- */
-extern rtk_api_ret_t rtk_svlan_servicePort_get(rtk_portmask_t *pSvlan_portmask);
-
-/* Function Name:
- *      rtk_svlan_servicePort_del
- * Description:
- *      Delete one service port in the specified device
- * Input:
- *      port - Port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API is removing SVLAN service port in the specified device.
- */
-extern rtk_api_ret_t rtk_svlan_servicePort_del(rtk_port_t port);
-
-/* Function Name:
- *      rtk_svlan_tpidEntry_set
- * Description:
- *      Configure accepted S-VLAN ether type.
- * Input:
- *      svlan_tag_id - Ether type of S-tag frame parsing in uplink ports.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      Ether type of S-tag in 802.1ad is 0x88a8 and there are existed ether type 0x9100 and 0x9200 for Q-in-Q SLAN design.
- *      User can set mathced ether type as service provider supported protocol.
- */
-extern rtk_api_ret_t rtk_svlan_tpidEntry_set(rtk_uint32 svlan_tag_id);
-
-/* Function Name:
- *      rtk_svlan_tpidEntry_get
- * Description:
- *      Get accepted S-VLAN ether type setting.
- * Input:
- *      None
- * Output:
- *      pSvlan_tag_id -  Ether type of S-tag frame parsing in uplink ports.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      This API is setting which port is connected to provider switch. All frames receiving from this port must
- *      contain accept SVID in S-tag field.
- */
-extern rtk_api_ret_t rtk_svlan_tpidEntry_get(rtk_uint32 *pSvlan_tag_id);
-
-/* Function Name:
- *      rtk_svlan_priorityRef_set
- * Description:
- *      Set S-VLAN upstream priority reference setting.
- * Input:
- *      ref - reference selection parameter.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The API can set the upstream SVLAN tag priority reference source. The related priority
- *      sources are as following:
- *      - REF_INTERNAL_PRI,
- *      - REF_CTAG_PRI,
- *      - REF_SVLAN_PRI,
- *      - REF_PB_PRI.
- */
-extern rtk_api_ret_t rtk_svlan_priorityRef_set(rtk_svlan_pri_ref_t ref);
-
-/* Function Name:
- *      rtk_svlan_priorityRef_get
- * Description:
- *      Get S-VLAN upstream priority reference setting.
- * Input:
- *      None
- * Output:
- *      pRef - reference selection parameter.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API can get the upstream SVLAN tag priority reference source. The related priority
- *      sources are as following:
- *      - REF_INTERNAL_PRI,
- *      - REF_CTAG_PRI,
- *      - REF_SVLAN_PRI,
- *      - REF_PB_PRI
- */
-extern rtk_api_ret_t rtk_svlan_priorityRef_get(rtk_svlan_pri_ref_t *pRef);
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_set
- * Description:
- *      Configure system SVLAN member content
- * Input:
- *      svid - SVLAN id
- *      psvlan_cfg - SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameter.
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_SVLAN_TABLE_FULL - SVLAN configuration is full.
- * Note:
- *      The API can set system 64 accepted s-tag frame format. Only 64 SVID S-tag frame will be accpeted
- *      to receiving from uplink ports. Other SVID S-tag frame or S-untagged frame will be droped by default setup.
- *      - rtk_svlan_memberCfg_t->svid is SVID of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->memberport is member port mask of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->fid is filtering database of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->priority is priority of SVLAN member configuration.
- */
-extern rtk_api_ret_t rtk_svlan_memberPortEntry_set(rtk_uint32 svid_idx, rtk_svlan_memberCfg_t *psvlan_cfg);
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_get
- * Description:
- *      Get SVLAN member Configure.
- * Input:
- *      svid - SVLAN id
- * Output:
- *      pSvlan_cfg - SVLAN member configuration
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can get system 64 accepted s-tag frame format. Only 64 SVID S-tag frame will be accpeted
- *      to receiving from uplink ports. Other SVID S-tag frame or S-untagged frame will be droped.
- */
-extern rtk_api_ret_t rtk_svlan_memberPortEntry_get(rtk_uint32 svid_idx, rtk_svlan_memberCfg_t *pSvlan_cfg);
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_adv_set
- * Description:
- *      Configure system SVLAN member by index
- * Input:
- *      idx         - Index (0 ~ 63)
- *      psvlan_cfg  - SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameter.
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_SVLAN_TABLE_FULL - SVLAN configuration is full.
- * Note:
- *      The API can set system 64 accepted s-tag frame format by index.
- *      - rtk_svlan_memberCfg_t->svid is SVID of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->memberport is member port mask of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->fid is filtering database of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->priority is priority of SVLAN member configuration.
- */
-extern rtk_api_ret_t rtk_svlan_memberPortEntry_adv_set(rtk_uint32 idx, rtk_svlan_memberCfg_t *pSvlan_cfg);
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_adv_get
- * Description:
- *      Get SVLAN member Configure by index.
- * Input:
- *      idx         - Index (0 ~ 63)
- * Output:
- *      pSvlan_cfg  - SVLAN member configuration
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can get system 64 accepted s-tag frame format. Only 64 SVID S-tag frame will be accpeted
- *      to receiving from uplink ports. Other SVID S-tag frame or S-untagged frame will be droped.
- */
-extern rtk_api_ret_t rtk_svlan_memberPortEntry_adv_get(rtk_uint32 idx, rtk_svlan_memberCfg_t *pSvlan_cfg);
-
-/* Function Name:
- *      rtk_svlan_defaultSvlan_set
- * Description:
- *      Configure default egress SVLAN.
- * Input:
- *      port - Source port
- *      svid - SVLAN id
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_INPUT                    - Invalid input parameter.
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- * Note:
- *      The API can set port n S-tag format index while receiving frame from port n
- *      is transmit through uplink port with s-tag field
- */
-extern rtk_api_ret_t rtk_svlan_defaultSvlan_set(rtk_port_t port, rtk_vlan_t svid);
-
-/* Function Name:
- *      rtk_svlan_defaultSvlan_get
- * Description:
- *      Get the configure default egress SVLAN.
- * Input:
- *      port - Source port
- * Output:
- *      pSvid - SVLAN VID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get port n S-tag format index while receiving frame from port n
- *      is transmit through uplink port with s-tag field
- */
-extern rtk_api_ret_t rtk_svlan_defaultSvlan_get(rtk_port_t port, rtk_vlan_t *pSvid);
-
-/* Function Name:
- *      rtk_svlan_c2s_add
- * Description:
- *      Configure SVLAN C2S table
- * Input:
- *      vid - VLAN ID
- *      src_port - Ingress Port
- *      svid - SVLAN VID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port ID.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set system C2S configuration. ASIC will check upstream's VID and assign related
- *      SVID to mathed packet. There are 128 SVLAN C2S configurations.
- */
-extern rtk_api_ret_t rtk_svlan_c2s_add(rtk_vlan_t vid, rtk_port_t src_port, rtk_vlan_t svid);
-
-/* Function Name:
- *      rtk_svlan_c2s_del
- * Description:
- *      Delete one C2S entry
- * Input:
- *      vid - VLAN ID
- *      src_port - Ingress Port
- *      svid - SVLAN VID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_VLAN_VID         - Invalid VID parameter.
- *      RT_ERR_PORT_ID          - Invalid port ID.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can delete system C2S configuration. There are 128 SVLAN C2S configurations.
- */
-extern rtk_api_ret_t rtk_svlan_c2s_del(rtk_vlan_t vid, rtk_port_t src_port);
-
-/* Function Name:
- *      rtk_svlan_c2s_get
- * Description:
- *      Get configure SVLAN C2S table
- * Input:
- *      vid - VLAN ID
- *      src_port - Ingress Port
- * Output:
- *      pSvid - SVLAN ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port ID.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- * Note:
- *     The API can get system C2S configuration. There are 128 SVLAN C2S configurations.
- */
-extern rtk_api_ret_t rtk_svlan_c2s_get(rtk_vlan_t vid, rtk_port_t src_port, rtk_vlan_t *pSvid);
-
-/* Function Name:
- *      rtk_svlan_untag_action_set
- * Description:
- *      Configure Action of downstream Un-Stag packet
- * Input:
- *      action  - Action for UnStag
- *      svid    - The SVID assigned to UnStag packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can configure action of downstream Un-Stag packet. A SVID assigned
- *      to the un-stag is also supported by this API. The parameter of svid is
- *      only referenced when the action is set to UNTAG_ASSIGN
- */
-extern rtk_api_ret_t rtk_svlan_untag_action_set(rtk_svlan_untag_action_t action, rtk_vlan_t svid);
-
-/* Function Name:
- *      rtk_svlan_untag_action_get
- * Description:
- *      Get Action of downstream Un-Stag packet
- * Input:
- *      None
- * Output:
- *      pAction  - Action for UnStag
- *      pSvid    - The SVID assigned to UnStag packet
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can Get action of downstream Un-Stag packet. A SVID assigned
- *      to the un-stag is also retrieved by this API. The parameter pSvid is
- *      only refernced when the action is UNTAG_ASSIGN
- */
-extern rtk_api_ret_t rtk_svlan_untag_action_get(rtk_svlan_untag_action_t *pAction, rtk_vlan_t *pSvid);
-
-/* Function Name:
- *      rtk_svlan_unmatch_action_set
- * Description:
- *      Configure Action of downstream Unmatch packet
- * Input:
- *      action  - Action for Unmatch
- *      svid    - The SVID assigned to Unmatch packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can configure action of downstream Un-match packet. A SVID assigned
- *      to the un-match is also supported by this API. The parameter od svid is
- *      only refernced when the action is set to UNMATCH_ASSIGN
- */
-extern rtk_api_ret_t rtk_svlan_unmatch_action_set(rtk_svlan_unmatch_action_t action, rtk_vlan_t svid);
-
-/* Function Name:
- *      rtk_svlan_unmatch_action_get
- * Description:
- *      Get Action of downstream Unmatch packet
- * Input:
- *      None
- * Output:
- *      pAction  - Action for Unmatch
- *      pSvid    - The SVID assigned to Unmatch packet
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can Get action of downstream Un-match packet. A SVID assigned
- *      to the un-match is also retrieved by this API. The parameter pSvid is
- *      only refernced when the action is UNMATCH_ASSIGN
- */
-extern rtk_api_ret_t rtk_svlan_unmatch_action_get(rtk_svlan_unmatch_action_t *pAction, rtk_vlan_t *pSvid);
-
-/* Function Name:
- *      rtk_svlan_dmac_vidsel_set
- * Description:
- *      Set DMAC CVID selection
- * Input:
- *      port    - Port
- *      enable  - state of DMAC CVID Selection
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      This API can set DMAC CVID Selection state
- */
-extern rtk_api_ret_t rtk_svlan_dmac_vidsel_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_svlan_dmac_vidsel_get
- * Description:
- *      Get DMAC CVID selection
- * Input:
- *      port    - Port
- * Output:
- *      pEnable - state of DMAC CVID Selection
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      This API can get DMAC CVID Selection state
- */
-extern rtk_api_ret_t rtk_svlan_dmac_vidsel_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_svlan_ipmc2s_add
- * Description:
- *      add ip multicast address to SVLAN
- * Input:
- *      svid    - SVLAN VID
- *      ipmc    - ip multicast address
- *      ipmcMsk - ip multicast mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can set IP mutlicast to SVID configuration. If upstream packet is IPv4 multicast
- *      packet and DIP is matched MC2S configuration, ASIC will assign egress SVID to the packet.
- *      There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-extern rtk_api_ret_t rtk_svlan_ipmc2s_add(ipaddr_t ipmc, ipaddr_t ipmcMsk, rtk_vlan_t svid);
-
-/* Function Name:
- *      rtk_svlan_ipmc2s_del
- * Description:
- *      delete ip multicast address to SVLAN
- * Input:
- *      ipmc    - ip multicast address
- *      ipmcMsk - ip multicast mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can delete IP mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-extern rtk_api_ret_t rtk_svlan_ipmc2s_del(ipaddr_t ipmc, ipaddr_t ipmcMsk);
-
-/* Function Name:
- *      rtk_svlan_ipmc2s_get
- * Description:
- *      Get ip multicast address to SVLAN
- * Input:
- *      ipmc    - ip multicast address
- *      ipmcMsk - ip multicast mask
- * Output:
- *      pSvid - SVLAN VID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- * Note:
- *      The API can get IP mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-extern rtk_api_ret_t rtk_svlan_ipmc2s_get(ipaddr_t ipmc, ipaddr_t ipmcMsk, rtk_vlan_t *pSvid);
-
-/* Function Name:
- *      rtk_svlan_l2mc2s_add
- * Description:
- *      Add L2 multicast address to SVLAN
- * Input:
- *      mac     - L2 multicast address
- *      macMsk  - L2 multicast address mask
- *      svid    - SVLAN VID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can set L2 Mutlicast to SVID configuration. If upstream packet is L2 multicast
- *      packet and DMAC is matched, ASIC will assign egress SVID to the packet. There are 32
- *      SVLAN multicast configurations for IP and L2 multicast.
- */
-extern rtk_api_ret_t rtk_svlan_l2mc2s_add(rtk_mac_t mac, rtk_mac_t macMsk, rtk_vlan_t svid);
-
-/* Function Name:
- *      rtk_svlan_l2mc2s_del
- * Description:
- *      delete L2 multicast address to SVLAN
- * Input:
- *      mac     - L2 multicast address
- *      macMsk  - L2 multicast address mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can delete Mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-extern rtk_api_ret_t rtk_svlan_l2mc2s_del(rtk_mac_t mac, rtk_mac_t macMsk);
-
-/* Function Name:
- *      rtk_svlan_l2mc2s_get
- * Description:
- *      Get L2 multicast address to SVLAN
- * Input:
- *      mac     - L2 multicast address
- *      macMsk  - L2 multicast address mask
- * Output:
- *      pSvid   - SVLAN VID
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can get L2 mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-extern rtk_api_ret_t rtk_svlan_l2mc2s_get(rtk_mac_t mac, rtk_mac_t macMsk, rtk_vlan_t *pSvid);
-
-/* Function Name:
- *      rtk_svlan_sp2c_add
- * Description:
- *      Add system SP2C configuration
- * Input:
- *      cvid        - VLAN ID
- *      dst_port    - Destination port of SVLAN to CVLAN configuration
- *      svid        - SVLAN VID
- *
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can add SVID & Destination Port to CVLAN configuration. The downstream frames with assigned
- *      SVID will be add C-tag with assigned CVID if the output port is the assigned destination port.
- *      There are 128 SP2C configurations.
- */
-extern rtk_api_ret_t rtk_svlan_sp2c_add(rtk_vlan_t svid, rtk_port_t dst_port, rtk_vlan_t cvid);
-
-/* Function Name:
- *      rtk_svlan_sp2c_get
- * Description:
- *      Get configure system SP2C content
- * Input:
- *      svid        - SVLAN VID
- *      dst_port    - Destination port of SVLAN to CVLAN configuration
- * Output:
- *      pCvid - VLAN ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- * Note:
- *     The API can get SVID & Destination Port to CVLAN configuration. There are 128 SP2C configurations.
- */
-extern rtk_api_ret_t rtk_svlan_sp2c_get(rtk_vlan_t svid, rtk_port_t dst_port, rtk_vlan_t *pCvid);
-
-/* Function Name:
- *      rtk_svlan_sp2c_del
- * Description:
- *      Delete system SP2C configuration
- * Input:
- *      svid        - SVLAN VID
- *      dst_port    - Destination port of SVLAN to CVLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- * Note:
- *      The API can delete SVID & Destination Port to CVLAN configuration. There are 128 SP2C configurations.
- */
-extern rtk_api_ret_t rtk_svlan_sp2c_del(rtk_vlan_t svid, rtk_port_t dst_port);
-
-
-/* Function Name:
- *      rtk_svlan_lookupType_set
- * Description:
- *      Set lookup type of SVLAN
- * Input:
- *      type        - lookup type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- * Note:
- *      none
- */
-extern rtk_api_ret_t rtk_svlan_lookupType_set(rtk_svlan_lookupType_t type);
-
-/* Function Name:
- *      rtk_svlan_lookupType_get
- * Description:
- *      Get lookup type of SVLAN
- * Input:
- *      pType       - lookup type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- * Note:
- *      none
- */
-extern rtk_api_ret_t rtk_svlan_lookupType_get(rtk_svlan_lookupType_t *pType);
-
-/* Function Name:
- *      rtk_svlan_trapPri_set
- * Description:
- *      Set svlan trap priority
- * Input:
- *      priority - priority for trap packets
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_QOS_INT_PRIORITY
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_svlan_trapPri_set(rtk_pri_t priority);
-
-/* Function Name:
- *      rtk_svlan_trapPri_get
- * Description:
- *      Get svlan trap priority
- * Input:
- *      None
- * Output:
- *      pPriority - priority for trap packets
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_svlan_trapPri_get(rtk_pri_t *pPriority);
-
-/* Function Name:
- *      rtk_svlan_unassign_action_set
- * Description:
- *      Configure Action of upstream without svid assign action
- * Input:
- *      action  - Action for Un-assign
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can configure action of upstream Un-assign svid packet. If action is not
- *      trap to CPU, the port-based SVID sure be assign as system need
- */
-extern rtk_api_ret_t rtk_svlan_unassign_action_set(rtk_svlan_unassign_action_t action);
-
-/* Function Name:
- *      rtk_svlan_unassign_action_get
- * Description:
- *      Get action of upstream without svid assignment
- * Input:
- *      None
- * Output:
- *      pAction  - Action for Un-assign
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- * Note:
- *      None
- */
-extern rtk_api_ret_t rtk_svlan_unassign_action_get(rtk_svlan_unassign_action_t *pAction);
-
-
-/* Function Name:
- *      rtk_svlan_checkAndCreateMbr
- * Description:
- *      Check and create Member configuration and return index
- * Input:
- *      vid  - VLAN id.
- * Output:
- *      pIndex  - Member configuration index
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_VLAN_VID     - Invalid VLAN ID.
- *      RT_ERR_TBL_FULL     - Member Configuration table full
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_svlan_checkAndCreateMbr(rtk_vlan_t vid, rtk_uint32 *pIndex);
-
-
-#endif /* __RTK_API_SVLAN_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/trap.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/trap.h
deleted file mode 100644
index 0cdb64a77b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/trap.h
+++ /dev/null
@@ -1,757 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes Trap module high-layer API defination
- *
- */
-
-#ifndef __RTK_API_TRAP_H__
-#define __RTK_API_TRAP_H__
-
-
-typedef enum rtk_trap_type_e
-{
-    TRAP_BRG_GROUP = 0,
-    TRAP_FD_PAUSE,
-    TRAP_SP_MCAST,
-    TRAP_1X_PAE,
-    TRAP_UNDEF_BRG_04,
-    TRAP_UNDEF_BRG_05,
-    TRAP_UNDEF_BRG_06,
-    TRAP_UNDEF_BRG_07,
-    TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
-    TRAP_UNDEF_BRG_09,
-    TRAP_UNDEF_BRG_0A,
-    TRAP_UNDEF_BRG_0B,
-    TRAP_UNDEF_BRG_0C,
-    TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
-    TRAP_8021AB,
-    TRAP_UNDEF_BRG_0F,
-    TRAP_BRG_MNGEMENT,
-    TRAP_UNDEFINED_11,
-    TRAP_UNDEFINED_12,
-    TRAP_UNDEFINED_13,
-    TRAP_UNDEFINED_14,
-    TRAP_UNDEFINED_15,
-    TRAP_UNDEFINED_16,
-    TRAP_UNDEFINED_17,
-    TRAP_UNDEFINED_18,
-    TRAP_UNDEFINED_19,
-    TRAP_UNDEFINED_1A,
-    TRAP_UNDEFINED_1B,
-    TRAP_UNDEFINED_1C,
-    TRAP_UNDEFINED_1D,
-    TRAP_UNDEFINED_1E,
-    TRAP_UNDEFINED_1F,
-    TRAP_GMRP,
-    TRAP_GVRP,
-    TRAP_UNDEF_GARP_22,
-    TRAP_UNDEF_GARP_23,
-    TRAP_UNDEF_GARP_24,
-    TRAP_UNDEF_GARP_25,
-    TRAP_UNDEF_GARP_26,
-    TRAP_UNDEF_GARP_27,
-    TRAP_UNDEF_GARP_28,
-    TRAP_UNDEF_GARP_29,
-    TRAP_UNDEF_GARP_2A,
-    TRAP_UNDEF_GARP_2B,
-    TRAP_UNDEF_GARP_2C,
-    TRAP_UNDEF_GARP_2D,
-    TRAP_UNDEF_GARP_2E,
-    TRAP_UNDEF_GARP_2F,
-    TRAP_CDP,
-    TRAP_CSSTP,
-    TRAP_LLDP,
-    TRAP_END,
-}rtk_trap_type_t;
-
-
-typedef enum rtk_mcast_type_e
-{
-    MCAST_L2 = 0,
-    MCAST_IPV4,
-    MCAST_IPV6,
-    MCAST_END
-} rtk_mcast_type_t;
-
-typedef enum rtk_trap_mcast_action_e
-{
-    MCAST_ACTION_FORWARD = 0,
-    MCAST_ACTION_DROP,
-    MCAST_ACTION_TRAP2CPU,
-    MCAST_ACTION_ROUTER_PORT,
-    MCAST_ACTION_DROP_EX_RMA,
-    MCAST_ACTION_END
-} rtk_trap_mcast_action_t;
-
-typedef enum rtk_trap_rma_action_e
-{
-    RMA_ACTION_FORWARD = 0,
-    RMA_ACTION_TRAP2CPU,
-    RMA_ACTION_DROP,
-    RMA_ACTION_FORWARD_EXCLUDE_CPU,
-    RMA_ACTION_END
-} rtk_trap_rma_action_t;
-
-typedef enum rtk_trap_ucast_action_e
-{
-    UCAST_ACTION_FORWARD_PMASK = 0,
-    UCAST_ACTION_DROP,
-    UCAST_ACTION_TRAP2CPU,
-    UCAST_ACTION_FLOODING,
-    UCAST_ACTION_END
-} rtk_trap_ucast_action_t;
-
-typedef enum rtk_trap_ucast_type_e
-{
-    UCAST_UNKNOWNDA = 0,
-    UCAST_UNKNOWNSA,
-    UCAST_UNMATCHSA,
-    UCAST_END
-} rtk_trap_ucast_type_t;
-
-typedef enum rtk_trap_reason_type_e
-{
-    TRAP_REASON_RMA = 0,
-    TRAP_REASON_OAM,
-    TRAP_REASON_1XUNAUTH,
-    TRAP_REASON_VLANSTACK,
-    TRAP_REASON_UNKNOWNMC,
-    TRAP_REASON_END,
-} rtk_trap_reason_type_t;
-
-
-/* Function Name:
- *      rtk_trap_unknownUnicastPktAction_set
- * Description:
- *      Set unknown unicast packet action configuration.
- * Input:
- *      port            - ingress port ID for unknown unicast packet
- *      ucast_action    - Unknown unicast action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- *          - UCAST_ACTION_FLOODING
- */
-rtk_api_ret_t rtk_trap_unknownUnicastPktAction_set(rtk_port_t port, rtk_trap_ucast_action_t ucast_action);
-
-/* Function Name:
- *      rtk_trap_unknownUnicastPktAction_get
- * Description:
- *      Get unknown unicast packet action configuration.
- * Input:
- *      port            - ingress port ID for unknown unicast packet
- * Output:
- *      pUcast_action   - Unknown unicast action.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- *      RT_ERR_NULL_POINTER        - Null pointer
- * Note:
- *      This API can get unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- *          - UCAST_ACTION_FLOODING
- */
-rtk_api_ret_t rtk_trap_unknownUnicastPktAction_get(rtk_port_t port, rtk_trap_ucast_action_t *pUcast_action);
-
-/* Function Name:
- *      rtk_trap_unknownMacPktAction_set
- * Description:
- *      Set unknown source MAC packet action configuration.
- * Input:
- *      ucast_action    - Unknown source MAC action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- */
-extern rtk_api_ret_t rtk_trap_unknownMacPktAction_set(rtk_trap_ucast_action_t ucast_action);
-
-/* Function Name:
- *      rtk_trap_unknownMacPktAction_get
- * Description:
- *      Get unknown source MAC packet action configuration.
- * Input:
- *      None.
- * Output:
- *      pUcast_action   - Unknown source MAC action.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NULL_POINTER        - Null Pointer.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_trap_unknownMacPktAction_get(rtk_trap_ucast_action_t *pUcast_action);
-
-/* Function Name:
- *      rtk_trap_unmatchMacPktAction_set
- * Description:
- *      Set unmatch source MAC packet action configuration.
- * Input:
- *      ucast_action    - Unknown source MAC action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- */
-extern rtk_api_ret_t rtk_trap_unmatchMacPktAction_set(rtk_trap_ucast_action_t ucast_action);
-
-/* Function Name:
- *      rtk_trap_unmatchMacPktAction_get
- * Description:
- *      Get unmatch source MAC packet action configuration.
- * Input:
- *      None.
- * Output:
- *      pUcast_action   - Unknown source MAC action.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- */
-extern rtk_api_ret_t rtk_trap_unmatchMacPktAction_get(rtk_trap_ucast_action_t *pUcast_action);
-
-/* Function Name:
- *      rtk_trap_unmatchMacMoving_set
- * Description:
- *      Set unmatch source MAC packet moving state.
- * Input:
- *      port        - Port ID.
- *      enable      - ENABLED: allow SA moving, DISABLE: don't allow SA moving.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- */
-extern rtk_api_ret_t rtk_trap_unmatchMacMoving_set(rtk_port_t port, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_trap_unmatchMacMoving_get
- * Description:
- *      Set unmatch source MAC packet moving state.
- * Input:
- *      port        - Port ID.
- * Output:
- *      pEnable     - ENABLED: allow SA moving, DISABLE: don't allow SA moving.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- */
-extern rtk_api_ret_t rtk_trap_unmatchMacMoving_get(rtk_port_t port, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_trap_unknownMcastPktAction_set
- * Description:
- *      Set behavior of unknown multicast
- * Input:
- *      port            - Port id.
- *      type            - unknown multicast packet type.
- *      mcast_action    - unknown multicast action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_NOT_ALLOWED  - Invalid action.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      When receives an unknown multicast packet, switch may trap, drop or flood this packet
- *      (1) The unknown multicast packet type is as following:
- *          - MCAST_L2
- *          - MCAST_IPV4
- *          - MCAST_IPV6
- *      (2) The unknown multicast action is as following:
- *          - MCAST_ACTION_FORWARD
- *          - MCAST_ACTION_DROP
- *          - MCAST_ACTION_TRAP2CPU
- */
-extern rtk_api_ret_t rtk_trap_unknownMcastPktAction_set(rtk_port_t port, rtk_mcast_type_t type, rtk_trap_mcast_action_t mcast_action);
-
-/* Function Name:
- *      rtk_trap_unknownMcastPktAction_get
- * Description:
- *      Get behavior of unknown multicast
- * Input:
- *      type - unknown multicast packet type.
- * Output:
- *      pMcast_action - unknown multicast action.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_NOT_ALLOWED      - Invalid operation.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      When receives an unknown multicast packet, switch may trap, drop or flood this packet
- *      (1) The unknown multicast packet type is as following:
- *          - MCAST_L2
- *          - MCAST_IPV4
- *          - MCAST_IPV6
- *      (2) The unknown multicast action is as following:
- *          - MCAST_ACTION_FORWARD
- *          - MCAST_ACTION_DROP
- *          - MCAST_ACTION_TRAP2CPU
- */
-extern rtk_api_ret_t rtk_trap_unknownMcastPktAction_get(rtk_port_t port, rtk_mcast_type_t type, rtk_trap_mcast_action_t *pMcast_action);
-
-/* Function Name:
- *      rtk_trap_lldpEnable_set
- * Description:
- *      Set LLDP enable.
- * Input:
- *      enabled - LLDP enable, 0: follow RMA, 1: use LLDP action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NOT_ALLOWED      - Invalid action.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      - DMAC                                                 Assignment
- *      - 01:80:c2:00:00:0e ethertype = 0x88CC    LLDP
- *      - 01:80:c2:00:00:03 ethertype = 0x88CC
- *      - 01:80:c2:00:00:00 ethertype = 0x88CC
-
- */
-extern rtk_api_ret_t rtk_trap_lldpEnable_set(rtk_enable_t enabled);
-
-/* Function Name:
- *      rtk_trap_lldpEnable_get
- * Description:
- *      Get LLDP status.
- * Input:
- *      None
- * Output:
- *      pEnabled - LLDP enable, 0: follow RMA, 1: use LLDP action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      LLDP is as following definition.
- *      - DMAC                                                 Assignment
- *      - 01:80:c2:00:00:0e ethertype = 0x88CC    LLDP
- *      - 01:80:c2:00:00:03 ethertype = 0x88CC
- *      - 01:80:c2:00:00:00 ethertype = 0x88CC
- */
-extern rtk_api_ret_t rtk_trap_lldpEnable_get(rtk_enable_t *pEnabled);
-
-/* Function Name:
- *      rtk_trap_reasonTrapToCpuPriority_set
- * Description:
- *      Set priority value of a packet that trapped to CPU port according to specific reason.
- * Input:
- *      type     - reason that trap to CPU port.
- *      priority - internal priority that is going to be set for specific trap reason.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT - The module is not initial
- *      RT_ERR_INPUT    - Invalid input parameter
- * Note:
- *      Currently the trap reason that supported are listed as follows:
- *      - TRAP_REASON_RMA
- *      - TRAP_REASON_OAM
- *      - TRAP_REASON_1XUNAUTH
- *      - TRAP_REASON_VLANSTACK
- *      - TRAP_REASON_UNKNOWNMC
- */
-extern rtk_api_ret_t rtk_trap_reasonTrapToCpuPriority_set(rtk_trap_reason_type_t type, rtk_pri_t priority);
-
-/* Function Name:
- *      rtk_trap_reasonTrapToCpuPriority_get
- * Description:
- *      Get priority value of a packet that trapped to CPU port according to specific reason.
- * Input:
- *      type      - reason that trap to CPU port.
- * Output:
- *      pPriority - configured internal priority for such reason.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT     - The module is not initial
- *      RT_ERR_INPUT        - Invalid input parameter
- *      RT_ERR_NULL_POINTER - NULL pointer
- * Note:
- *      Currently the trap reason that supported are listed as follows:
- *      - TRAP_REASON_RMA
- *      - TRAP_REASON_OAM
- *      - TRAP_REASON_1XUNAUTH
- *      - TRAP_REASON_VLANSTACK
- *      - TRAP_REASON_UNKNOWNMC
- */
-extern rtk_api_ret_t rtk_trap_reasonTrapToCpuPriority_get(rtk_trap_reason_type_t type, rtk_pri_t *pPriority);
-
-/* Function Name:
- *      rtk_trap_rmaAction_set
- * Description:
- *      Set Reserved multicast address action configuration.
- * Input:
- *      type    - rma type.
- *      rma_action - RMA action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid IFG parameter
- * Note:
- *
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      (1)They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- *      (2) The RMA action is as following:
- *      - RMA_ACTION_FORWARD
- *      - RMA_ACTION_TRAP2CPU
- *      - RMA_ACTION_DROP
- *      - RMA_ACTION_FORWARD_EXCLUDE_CPU
- */
-extern rtk_api_ret_t rtk_trap_rmaAction_set(rtk_trap_type_t type, rtk_trap_rma_action_t rma_action);
-
-/* Function Name:
- *      rtk_trap_rmaAction_get
- * Description:
- *      Get Reserved multicast address action configuration.
- * Input:
- *      type - rma type.
- * Output:
- *      pRma_action - RMA action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      (1)They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- *      (2) The RMA action is as following:
- *      - RMA_ACTION_FORWARD
- *      - RMA_ACTION_TRAP2CPU
- *      - RMA_ACTION_DROP
- *      - RMA_ACTION_FORWARD_EXCLUDE_CPU
- */
-extern rtk_api_ret_t rtk_trap_rmaAction_get(rtk_trap_type_t type, rtk_trap_rma_action_t *pRma_action);
-
-/* Function Name:
- *      rtk_trap_rmaKeepFormat_set
- * Description:
- *      Set Reserved multicast address keep format configuration.
- * Input:
- *      type    - rma type.
- *      enable - enable keep format.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid IFG parameter
- * Note:
- *
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- */
-extern rtk_api_ret_t rtk_trap_rmaKeepFormat_set(rtk_trap_type_t type, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_trap_rmaKeepFormat_get
- * Description:
- *      Get Reserved multicast address action configuration.
- * Input:
- *      type - rma type.
- * Output:
- *      pEnable - keep format status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- */
-extern rtk_api_ret_t rtk_trap_rmaKeepFormat_get(rtk_trap_type_t type, rtk_enable_t *pEnable);
-
-
-#endif /* __RTK_API_TRAP_H__ */
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/trunk.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/trunk.h
deleted file mode 100644
index dff61769df..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/trunk.h
+++ /dev/null
@@ -1,328 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes Trunk module high-layer TRUNK defination
- *
- */
-
-#ifndef __RTK_API_TRUNK_H__
-#define __RTK_API_TRUNK_H__
-
-/*
- * Data Type Declaration
- */
-#define    RTK_TRUNK_DPORT_HASH_MASK     0x40
-#define    RTK_TRUNK_SPORT_HASH_MASK     0x20
-#define    RTK_TRUNK_DIP_HASH_MASK       0x10
-#define    RTK_TRUNK_SIP_HASH_MASK       0x8
-#define    RTK_TRUNK_DMAC_HASH_MASK      0x4
-#define    RTK_TRUNK_SMAC_HASH_MASK      0x2
-#define    RTK_TRUNK_SPA_HASH_MASK       0x1
-
-
-#define RTK_MAX_NUM_OF_TRUNK_HASH_VAL               16
-
-typedef struct  rtk_trunk_hashVal2Port_s
-{
-    rtk_uint8 value[RTK_MAX_NUM_OF_TRUNK_HASH_VAL];
-} rtk_trunk_hashVal2Port_t;
-
-typedef enum rtk_trunk_group_e
-{
-    TRUNK_GROUP0 = 0,
-    TRUNK_GROUP1,
-    TRUNK_GROUP2,
-    TRUNK_GROUP3,
-    TRUNK_GROUP_END
-} rtk_trunk_group_t;
-
-typedef enum rtk_trunk_separateType_e
-{
-    SEPARATE_NONE = 0,
-    SEPARATE_FLOOD,
-    SEPARATE_END
-
-} rtk_trunk_separateType_t;
-
-typedef enum rtk_trunk_mode_e
-{
-    TRUNK_MODE_NORMAL = 0,
-    TRUNK_MODE_DUMB,
-    TRUNK_MODE_END
-} rtk_trunk_mode_t;
-
-/* Function Name:
- *      rtk_trunk_port_set
- * Description:
- *      Set trunking group available port mask
- * Input:
- *      trk_gid                 - trunk group id
- *      pTrunk_member_portmask  - Logic trunking member port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      The API can set port trunking group port mask. Each port trunking group has max 4 ports.
- *      If enabled port mask has less than 2 ports available setting, then this trunking group function is disabled.
- */
-extern rtk_api_ret_t rtk_trunk_port_set(rtk_trunk_group_t trk_gid, rtk_portmask_t *pTrunk_member_portmask);
-
-/* Function Name:
- *      rtk_trunk_port_get
- * Description:
- *      Get trunking group available port mask
- * Input:
- *      trk_gid - trunk group id
- * Output:
- *      pTrunk_member_portmask - Logic trunking member port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- * Note:
- *      The API can get 2 port trunking group.
- */
-extern rtk_api_ret_t rtk_trunk_port_get(rtk_trunk_group_t trk_gid, rtk_portmask_t *pTrunk_member_portmask);
-
-/* Function Name:
- *      rtk_trunk_distributionAlgorithm_set
- * Description:
- *      Set port trunking hash select sources
- * Input:
- *      trk_gid         - trunk group id
- *      algo_bitmask    - Bitmask of the distribution algorithm
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- *      RT_ERR_LA_HASHMASK  - Hash algorithm selection error.
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      The API can set port trunking hash algorithm sources.
- *      7 bits mask for link aggregation group0 hash parameter selection {DIP, SIP, DMAC, SMAC, SPA}
- *      - 0b0000001: SPA
- *      - 0b0000010: SMAC
- *      - 0b0000100: DMAC
- *      - 0b0001000: SIP
- *      - 0b0010000: DIP
- *      - 0b0100000: TCP/UDP Source Port
- *      - 0b1000000: TCP/UDP Destination Port
- *      Example:
- *      - 0b0000011: SMAC & SPA
- *      - Note that it could be an arbitrary combination or independent set
- */
-extern rtk_api_ret_t rtk_trunk_distributionAlgorithm_set(rtk_trunk_group_t trk_gid, rtk_uint32 algo_bitmask);
-
-/* Function Name:
- *      rtk_trunk_distributionAlgorithm_get
- * Description:
- *      Get port trunking hash select sources
- * Input:
- *      trk_gid - trunk group id
- * Output:
- *      pAlgo_bitmask -  Bitmask of the distribution algorithm
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- * Note:
- *      The API can get port trunking hash algorithm sources.
- */
-extern rtk_api_ret_t rtk_trunk_distributionAlgorithm_get(rtk_trunk_group_t trk_gid, rtk_uint32 *pAlgo_bitmask);
-
-/* Function Name:
- *      rtk_trunk_trafficSeparate_set
- * Description:
- *      Set the traffic separation setting of a trunk group from the specified device.
- * Input:
- *      trk_gid      - trunk group id
- *      separateType     - traffic separation setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID     - invalid unit id
- *      RT_ERR_LA_TRUNK_ID - invalid trunk ID
- *      RT_ERR_LA_HASHMASK - invalid hash mask
- * Note:
- *      SEPARATE_NONE: disable traffic separation
- *      SEPARATE_FLOOD: trunk MSB link up port is dedicated to TX flooding (L2 lookup miss) traffic
- */
-extern rtk_api_ret_t rtk_trunk_trafficSeparate_set(rtk_trunk_group_t trk_gid, rtk_trunk_separateType_t separateType);
-
-/* Function Name:
- *      rtk_trunk_trafficSeparate_get
- * Description:
- *      Get the traffic separation setting of a trunk group from the specified device.
- * Input:
- *      trk_gid        - trunk group id
- * Output:
- *      pSeparateType   - pointer separated traffic type
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_LA_TRUNK_ID  - invalid trunk ID
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      SEPARATE_NONE: disable traffic separation
- *      SEPARATE_FLOOD: trunk MSB link up port is dedicated to TX flooding (L2 lookup miss) traffic
- */
-extern rtk_api_ret_t rtk_trunk_trafficSeparate_get(rtk_trunk_group_t trk_gid, rtk_trunk_separateType_t *pSeparateType);
-
-
-/* Function Name:
- *      rtk_trunk_mode_set
- * Description:
- *      Set the trunk mode to the specified device.
- * Input:
- *      mode - trunk mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT   - invalid input parameter
- * Note:
- *      The enum of the trunk mode as following
- *      - TRUNK_MODE_NORMAL
- *      - TRUNK_MODE_DUMB
- */
-extern rtk_api_ret_t rtk_trunk_mode_set(rtk_trunk_mode_t mode);
-
-/* Function Name:
- *      rtk_trunk_mode_get
- * Description:
- *      Get the trunk mode from the specified device.
- * Input:
- *      None
- * Output:
- *      pMode - pointer buffer of trunk mode
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      The enum of the trunk mode as following
- *      - TRUNK_MODE_NORMAL
- *      - TRUNK_MODE_DUMB
- */
-extern rtk_api_ret_t rtk_trunk_mode_get(rtk_trunk_mode_t *pMode);
-
-/* Function Name:
- *      rtk_trunk_trafficPause_set
- * Description:
- *      Set the traffic pause setting of a trunk group.
- * Input:
- *      trk_gid      - trunk group id
- *      enable       - traffic pause state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_LA_TRUNK_ID - invalid trunk ID
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_trunk_trafficPause_set(rtk_trunk_group_t trk_gid, rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_trunk_trafficPause_get
- * Description:
- *      Get the traffic pause setting of a trunk group.
- * Input:
- *      trk_gid        - trunk group id
- * Output:
- *      pEnable        - pointer of traffic pause state.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_LA_TRUNK_ID  - invalid trunk ID
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_trunk_trafficPause_get(rtk_trunk_group_t trk_gid, rtk_enable_t *pEnable);
-
-/* Function Name:
- *      rtk_trunk_hashMappingTable_set
- * Description:
- *      Set hash value to port array in the trunk group id from the specified device.
- * Input:
- *      trk_gid          - trunk group id
- *      pHash2Port_array - ports associate with the hash value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID            - invalid unit id
- *      RT_ERR_LA_TRUNK_ID        - invalid trunk ID
- *      RT_ERR_NULL_POINTER       - input parameter may be null pointer
- *      RT_ERR_LA_TRUNK_NOT_EXIST - the trunk doesn't exist
- *      RT_ERR_LA_NOT_MEMBER_PORT - the port is not a member port of the trunk
- *      RT_ERR_LA_CPUPORT         - CPU port can not be aggregated port
- * Note:
- *      Trunk group 0 & 1 shares the same hash mapping table.
- *      Trunk group 2 uses a independent table.
- */
-extern rtk_api_ret_t rtk_trunk_hashMappingTable_set(rtk_trunk_group_t trk_gid, rtk_trunk_hashVal2Port_t *pHash2Port_array);
-
-/* Function Name:
- *      rtk_trunk_hashMappingTable_get
- * Description:
- *      Get hash value to port array in the trunk group id from the specified device.
- * Input:
- *      trk_gid          - trunk group id
- * Output:
- *      pHash2Port_array - pointer buffer of ports associate with the hash value
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_LA_TRUNK_ID  - invalid trunk ID
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      Trunk group 0 & 1 shares the same hash mapping table.
- *      Trunk group 2 uses a independent table.
- */
-extern rtk_api_ret_t rtk_trunk_hashMappingTable_get(rtk_trunk_group_t trk_gid, rtk_trunk_hashVal2Port_t *pHash2Port_array);
-
-/* Function Name:
- *      rtk_trunk_portQueueEmpty_get
- * Description:
- *      Get the port mask which all queues are empty.
- * Input:
- *      None.
- * Output:
- *      pEmpty_portmask   - pointer empty port mask
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_trunk_portQueueEmpty_get(rtk_portmask_t *pEmpty_portmask);
-
-#endif /* __RTK_API_TRUNK_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/vlan.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/vlan.h
deleted file mode 100644
index 8569fc0d40..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/vlan.h
+++ /dev/null
@@ -1,892 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367/RTL8367C switch high-level API
- *
- * Feature : The file includes Trap module high-layer VLAN defination
- *
- */
-
-#ifndef __RTK_API_VLAN_H__
-#define __RTK_API_VLAN_H__
-
-
-/*
- * Data Type Declaration
- */
-#define RTK_MAX_NUM_OF_PROTO_TYPE                   0xFFFF
-#define RTK_MAX_NUM_OF_MSTI                         0xF
-#define RTK_FID_MAX                                 0xF
-
-typedef struct  rtk_vlan_cfg_s
-{
-    rtk_portmask_t  mbr;
-    rtk_portmask_t  untag;
-    rtk_uint16      ivl_en;
-    rtk_uint16      fid_msti;
-    rtk_uint16      envlanpol;
-    rtk_uint16      meteridx;
-    rtk_uint16      vbpen;
-    rtk_uint16      vbpri;
-}rtk_vlan_cfg_t;
-
-typedef struct  rtk_vlan_mbrcfg_s
-{
-    rtk_uint16      evid;
-    rtk_portmask_t  mbr;
-    rtk_uint16      fid_msti;
-    rtk_uint16      envlanpol;
-    rtk_uint16      meteridx;
-    rtk_uint16      vbpen;
-    rtk_uint16      vbpri;
-}rtk_vlan_mbrcfg_t;
-
-typedef rtk_uint32  rtk_stp_msti_id_t;     /* MSTI ID  */
-
-typedef enum rtk_stp_state_e
-{
-    STP_STATE_DISABLED = 0,
-    STP_STATE_BLOCKING,
-    STP_STATE_LEARNING,
-    STP_STATE_FORWARDING,
-    STP_STATE_END
-} rtk_stp_state_t;
-
-typedef rtk_uint32  rtk_vlan_proto_type_t;     /* protocol and port based VLAN protocol type  */
-
-
-typedef enum rtk_vlan_acceptFrameType_e
-{
-    ACCEPT_FRAME_TYPE_ALL = 0,             /* untagged, priority-tagged and tagged */
-    ACCEPT_FRAME_TYPE_TAG_ONLY,         /* tagged */
-    ACCEPT_FRAME_TYPE_UNTAG_ONLY,     /* untagged and priority-tagged */
-    ACCEPT_FRAME_TYPE_END
-} rtk_vlan_acceptFrameType_t;
-
-
-/* frame type of protocol vlan - reference 802.1v standard */
-typedef enum rtk_vlan_protoVlan_frameType_e
-{
-    FRAME_TYPE_ETHERNET = 0,
-    FRAME_TYPE_LLCOTHER,
-    FRAME_TYPE_RFC1042,
-    FRAME_TYPE_END
-} rtk_vlan_protoVlan_frameType_t;
-
-/* Protocol-and-port-based Vlan structure */
-typedef struct rtk_vlan_protoAndPortInfo_s
-{
-    rtk_uint32                         proto_type;
-    rtk_vlan_protoVlan_frameType_t frame_type;
-    rtk_vlan_t                     cvid;
-    rtk_pri_t                     cpri;
-}rtk_vlan_protoAndPortInfo_t;
-
-/* tagged mode of VLAN - reference realtek private specification */
-typedef enum rtk_vlan_tagMode_e
-{
-    VLAN_TAG_MODE_ORIGINAL = 0,
-    VLAN_TAG_MODE_KEEP_FORMAT,
-    VLAN_TAG_MODE_PRI,
-    VLAN_TAG_MODE_REAL_KEEP_FORMAT,
-    VLAN_TAG_MODE_END
-} rtk_vlan_tagMode_t;
-
-typedef enum rtk_vlan_resVidAction_e
-{
-    RESVID_ACTION_UNTAG = 0,
-    RESVID_ACTION_TAG,
-    RESVID_ACTION_END
-}
-rtk_vlan_resVidAction_t;
-
-/* Function Name:
- *      rtk_vlan_init
- * Description:
- *      Initialize VLAN.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      VLAN is disabled by default. User has to call this API to enable VLAN before
- *      using it. And It will set a default VLAN(vid 1) including all ports and set
- *      all ports PVID to the default VLAN.
- */
-extern rtk_api_ret_t rtk_vlan_init(void);
-
-/* Function Name:
- *      rtk_vlan_set
- * Description:
- *      Set a VLAN entry.
- * Input:
- *      vid - VLAN ID to configure.
- *      pVlanCfg - VLAN Configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameters.
- *      RT_ERR_L2_FID               - Invalid FID.
- *      RT_ERR_VLAN_PORT_MBR_EXIST  - Invalid member port mask.
- *      RT_ERR_VLAN_VID             - Invalid VID parameter.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_set(rtk_vlan_t vid, rtk_vlan_cfg_t *pVlanCfg);
-
-/* Function Name:
- *      rtk_vlan_get
- * Description:
- *      Get a VLAN entry.
- * Input:
- *      vid - VLAN ID to configure.
- * Output:
- *      pVlanCfg - VLAN Configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_get(rtk_vlan_t vid, rtk_vlan_cfg_t *pVlanCfg);
-
-/* Function Name:
- *      rtk_vlan_egrFilterEnable_set
- * Description:
- *      Set VLAN egress filter.
- * Input:
- *      egrFilter - Egress filtering
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid input parameters.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_egrFilterEnable_set(rtk_enable_t egrFilter);
-
-/* Function Name:
- *      rtk_vlan_egrFilterEnable_get
- * Description:
- *      Get VLAN egress filter.
- * Input:
- *      pEgrFilter - Egress filtering
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - NULL Pointer.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_egrFilterEnable_get(rtk_enable_t *pEgrFilter);
-
-/* Function Name:
- *      rtk_vlan_mbrCfg_set
- * Description:
- *      Set a VLAN Member Configuration entry by index.
- * Input:
- *      idx     - Index of VLAN Member Configuration.
- *      pMbrcfg - VLAN member Configuration.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *     Set a VLAN Member Configuration entry by index.
- */
-extern rtk_api_ret_t rtk_vlan_mbrCfg_set(rtk_uint32 idx, rtk_vlan_mbrcfg_t *pMbrcfg);
-
-/* Function Name:
- *      rtk_vlan_mbrCfg_get
- * Description:
- *      Get a VLAN Member Configuration entry by index.
- * Input:
- *      idx - Index of VLAN Member Configuration.
- * Output:
- *      pMbrcfg - VLAN member Configuration.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *     Get a VLAN Member Configuration entry by index.
- */
-extern rtk_api_ret_t rtk_vlan_mbrCfg_get(rtk_uint32 idx, rtk_vlan_mbrcfg_t *pMbrcfg);
-
-/* Function Name:
- *     rtk_vlan_portPvid_set
- * Description:
- *      Set port to specified VLAN ID(PVID).
- * Input:
- *      port - Port id.
- *      pvid - Specified VLAN ID.
- *      priority - 802.1p priority for the PVID.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_VLAN_PRIORITY        - Invalid priority.
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - VLAN entry not found.
- *      RT_ERR_VLAN_VID             - Invalid VID parameter.
- * Note:
- *       The API is used for Port-based VLAN. The untagged frame received from the
- *       port will be classified to the specified VLAN and assigned to the specified priority.
- */
-extern rtk_api_ret_t rtk_vlan_portPvid_set(rtk_port_t port, rtk_vlan_t pvid, rtk_pri_t priority);
-
-/* Function Name:
- *      rtk_vlan_portPvid_get
- * Description:
- *      Get VLAN ID(PVID) on specified port.
- * Input:
- *      port - Port id.
- * Output:
- *      pPvid - Specified VLAN ID.
- *      pPriority - 802.1p priority for the PVID.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *     The API can get the PVID and 802.1p priority for the PVID of Port-based VLAN.
- */
-extern rtk_api_ret_t rtk_vlan_portPvid_get(rtk_port_t port, rtk_vlan_t *pPvid, rtk_pri_t *pPriority);
-
-/* Function Name:
- *      rtk_vlan_portIgrFilterEnable_set
- * Description:
- *      Set VLAN ingress for each port.
- * Input:
- *      port - Port id.
- *      igr_filter - VLAN ingress function enable status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The status of vlan ingress filter is as following:
- *      - DISABLED
- *      - ENABLED
- *      While VLAN function is enabled, ASIC will decide VLAN ID for each received frame and get belonged member
- *      ports from VLAN table. If received port is not belonged to VLAN member ports, ASIC will drop received frame if VLAN ingress function is enabled.
- */
-extern rtk_api_ret_t rtk_vlan_portIgrFilterEnable_set(rtk_port_t port, rtk_enable_t igr_filter);
-
-/* Function Name:
- *      rtk_vlan_portIgrFilterEnable_get
- * Description:
- *      Get VLAN Ingress Filter
- * Input:
- *      port        - Port id.
- * Output:
- *      pIgr_filter - VLAN ingress function enable status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *     The API can Get the VLAN ingress filter status.
- *     The status of vlan ingress filter is as following:
- *     - DISABLED
- *     - ENABLED
- */
-extern rtk_api_ret_t rtk_vlan_portIgrFilterEnable_get(rtk_port_t port, rtk_enable_t *pIgr_filter);
-
-/* Function Name:
- *      rtk_vlan_portAcceptFrameType_set
- * Description:
- *      Set VLAN accept_frame_type
- * Input:
- *      port                - Port id.
- *      accept_frame_type   - accept frame type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_PORT_ID                  - Invalid port number.
- *      RT_ERR_VLAN_ACCEPT_FRAME_TYPE   - Invalid frame type.
- * Note:
- *      The API is used for checking 802.1Q tagged frames.
- *      The accept frame type as following:
- *      - ACCEPT_FRAME_TYPE_ALL
- *      - ACCEPT_FRAME_TYPE_TAG_ONLY
- *      - ACCEPT_FRAME_TYPE_UNTAG_ONLY
- */
-extern rtk_api_ret_t rtk_vlan_portAcceptFrameType_set(rtk_port_t port, rtk_vlan_acceptFrameType_t accept_frame_type);
-
-/* Function Name:
- *      rtk_vlan_portAcceptFrameType_get
- * Description:
- *      Get VLAN accept_frame_type
- * Input:
- *      port - Port id.
- * Output:
- *      pAccept_frame_type - accept frame type
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *     The API can Get the VLAN ingress filter.
- *     The accept frame type as following:
- *     - ACCEPT_FRAME_TYPE_ALL
- *     - ACCEPT_FRAME_TYPE_TAG_ONLY
- *     - ACCEPT_FRAME_TYPE_UNTAG_ONLY
- */
-extern rtk_api_ret_t rtk_vlan_portAcceptFrameType_get(rtk_port_t port, rtk_vlan_acceptFrameType_t *pAccept_frame_type);
-
-/* Function Name:
- *      rtk_vlan_tagMode_set
- * Description:
- *      Set CVLAN egress tag mode
- * Input:
- *      port        - Port id.
- *      tag_mode    - The egress tag mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The API can set Egress tag mode. There are 4 mode for egress tag:
- *      - VLAN_TAG_MODE_ORIGINAL,
- *      - VLAN_TAG_MODE_KEEP_FORMAT,
- *      - VLAN_TAG_MODE_PRI.
- *      - VLAN_TAG_MODE_REAL_KEEP_FORMAT,
- */
-extern rtk_api_ret_t rtk_vlan_tagMode_set(rtk_port_t port, rtk_vlan_tagMode_t tag_mode);
-
-/* Function Name:
- *      rtk_vlan_tagMode_get
- * Description:
- *      Get CVLAN egress tag mode
- * Input:
- *      port - Port id.
- * Output:
- *      pTag_mode - The egress tag mode.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get Egress tag mode. There are 4 mode for egress tag:
- *      - VLAN_TAG_MODE_ORIGINAL,
- *      - VLAN_TAG_MODE_KEEP_FORMAT,
- *      - VLAN_TAG_MODE_PRI.
- *      - VLAN_TAG_MODE_REAL_KEEP_FORMAT,
- */
-extern rtk_api_ret_t rtk_vlan_tagMode_get(rtk_port_t port, rtk_vlan_tagMode_t *pTag_mode);
-
-/* Function Name:
- *      rtk_vlan_transparent_set
- * Description:
- *      Set VLAN transparent mode
- * Input:
- *      egr_port        - Egress Port id.
- *      pIgr_pmask      - Ingress Port Mask.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_vlan_transparent_set(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask);
-
-/* Function Name:
- *      rtk_vlan_transparent_get
- * Description:
- *      Get VLAN transparent mode
- * Input:
- *      egr_port        - Egress Port id.
- * Output:
- *      pIgr_pmask      - Ingress Port Mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_vlan_transparent_get(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask);
-
-/* Function Name:
- *      rtk_vlan_keep_set
- * Description:
- *      Set VLAN egress keep mode
- * Input:
- *      egr_port        - Egress Port id.
- *      pIgr_pmask      - Ingress Port Mask.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_vlan_keep_set(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask);
-
-/* Function Name:
- *      rtk_vlan_keep_get
- * Description:
- *      Get VLAN egress keep mode
- * Input:
- *      egr_port        - Egress Port id.
- * Output:
- *      pIgr_pmask      - Ingress Port Mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-extern rtk_api_ret_t rtk_vlan_keep_get(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask);
-
-/* Function Name:
- *      rtk_vlan_stg_set
- * Description:
- *      Set spanning tree group instance of the vlan to the specified device
- * Input:
- *      vid - Specified VLAN ID.
- *      stg - spanning tree group instance.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_MSTI         - Invalid msti parameter
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *      The API can set spanning tree group instance of the vlan to the specified device.
- */
-extern rtk_api_ret_t rtk_vlan_stg_set(rtk_vlan_t vid, rtk_stp_msti_id_t stg);
-
-/* Function Name:
- *      rtk_vlan_stg_get
- * Description:
- *      Get spanning tree group instance of the vlan to the specified device
- * Input:
- *      vid - Specified VLAN ID.
- * Output:
- *      pStg - spanning tree group instance.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *      The API can get spanning tree group instance of the vlan to the specified device.
- */
-extern rtk_api_ret_t rtk_vlan_stg_get(rtk_vlan_t vid, rtk_stp_msti_id_t *pStg);
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_add
- * Description:
- *      Add the protocol-and-port-based vlan to the specified port of device.
- * Input:
- *      port  - Port id.
- *      pInfo - Protocol and port based VLAN configuration information.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_VLAN_VID         - Invalid VID parameter.
- *      RT_ERR_VLAN_PRIORITY    - Invalid priority.
- *      RT_ERR_TBL_FULL         - Table is full.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *      The frame type is shown in the following:
- *      - FRAME_TYPE_ETHERNET
- *      - FRAME_TYPE_RFC1042
- *      - FRAME_TYPE_LLCOTHER
- */
-extern rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_add(rtk_port_t port, rtk_vlan_protoAndPortInfo_t *pInfo);
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_get
- * Description:
- *      Get the protocol-and-port-based vlan to the specified port of device.
- * Input:
- *      port - Port id.
- *      proto_type - protocol-and-port-based vlan protocol type.
- *      frame_type - protocol-and-port-based vlan frame type.
- * Output:
- *      pInfo - Protocol and port based VLAN configuration information.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- *      RT_ERR_TBL_FULL         - Table is full.
- * Note:
- *     The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *     The frame type is shown in the following:
- *      - FRAME_TYPE_ETHERNET
- *      - FRAME_TYPE_RFC1042
- *      - FRAME_TYPE_LLCOTHER
- */
-extern rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_get(rtk_port_t port, rtk_vlan_proto_type_t proto_type, rtk_vlan_protoVlan_frameType_t frame_type, rtk_vlan_protoAndPortInfo_t *pInfo);
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_del
- * Description:
- *      Delete the protocol-and-port-based vlan from the specified port of device.
- * Input:
- *      port        - Port id.
- *      proto_type  - protocol-and-port-based vlan protocol type.
- *      frame_type  - protocol-and-port-based vlan frame type.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- *      RT_ERR_TBL_FULL         - Table is full.
- * Note:
- *     The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *     The frame type is shown in the following:
- *      - FRAME_TYPE_ETHERNET
- *      - FRAME_TYPE_RFC1042
- *      - FRAME_TYPE_LLCOTHER
- */
-extern rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_del(rtk_port_t port, rtk_vlan_proto_type_t proto_type, rtk_vlan_protoVlan_frameType_t frame_type);
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_delAll
- * Description:
- *     Delete all protocol-and-port-based vlans from the specified port of device.
- * Input:
- *      port - Port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *     The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *     Delete all flow table protocol-and-port-based vlan entries.
- */
-extern rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_delAll(rtk_port_t port);
-
-/* Function Name:
- *      rtk_vlan_portFid_set
- * Description:
- *      Set port-based filtering database
- * Input:
- *      port - Port id.
- *      enable - ebable port-based FID
- *      fid - Specified filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_L2_FID - Invalid fid.
- *      RT_ERR_INPUT - Invalid input parameter.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can set port-based filtering database. If the function is enabled, all input
- *      packets will be assigned to the port-based fid regardless vlan tag.
- */
-extern rtk_api_ret_t rtk_vlan_portFid_set(rtk_port_t port, rtk_enable_t enable, rtk_fid_t fid);
-
-/* Function Name:
- *      rtk_vlan_portFid_get
- * Description:
- *      Get port-based filtering database
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - ebable port-based FID
- *      pFid - Specified filtering database.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can get port-based filtering database status. If the function is enabled, all input
- *      packets will be assigned to the port-based fid regardless vlan tag.
- */
-extern rtk_api_ret_t rtk_vlan_portFid_get(rtk_port_t port, rtk_enable_t *pEnable, rtk_fid_t *pFid);
-
-/* Function Name:
- *      rtk_vlan_UntagDscpPriorityEnable_set
- * Description:
- *      Set Untag DSCP priority assign
- * Input:
- *      enable - state of Untag DSCP priority assign
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_ENABLE          - Invalid input parameters.
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_UntagDscpPriorityEnable_set(rtk_enable_t enable);
-
-/* Function Name:
- *      rtk_vlan_UntagDscpPriorityEnable_get
- * Description:
- *      Get Untag DSCP priority assign
- * Input:
- *      None
- * Output:
- *      pEnable - state of Untag DSCP priority assign
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_UntagDscpPriorityEnable_get(rtk_enable_t *pEnable);
-
-
-/*Spanning Tree*/
-/* Function Name:
- *      rtk_stp_mstpState_set
- * Description:
- *      Configure spanning tree state per each port.
- * Input:
- *      port - Port id
- *      msti - Multiple spanning tree instance.
- *      stp_state - Spanning tree state for msti
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_MSTI         - Invalid msti parameter.
- *      RT_ERR_MSTP_STATE   - Invalid STP state.
- * Note:
- *      System supports per-port multiple spanning tree state for each msti.
- *      There are four states supported by ASIC.
- *      - STP_STATE_DISABLED
- *      - STP_STATE_BLOCKING
- *      - STP_STATE_LEARNING
- *      - STP_STATE_FORWARDING
- */
-extern rtk_api_ret_t rtk_stp_mstpState_set(rtk_stp_msti_id_t msti, rtk_port_t port, rtk_stp_state_t stp_state);
-
-/* Function Name:
- *      rtk_stp_mstpState_get
- * Description:
- *      Get spanning tree state per each port.
- * Input:
- *      port - Port id.
- *      msti - Multiple spanning tree instance.
- * Output:
- *      pStp_state - Spanning tree state for msti
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_MSTI         - Invalid msti parameter.
- * Note:
- *      System supports per-port multiple spanning tree state for each msti.
- *      There are four states supported by ASIC.
- *      - STP_STATE_DISABLED
- *      - STP_STATE_BLOCKING
- *      - STP_STATE_LEARNING
- *      - STP_STATE_FORWARDING
- */
-extern rtk_api_ret_t rtk_stp_mstpState_get(rtk_stp_msti_id_t msti, rtk_port_t port, rtk_stp_state_t *pStp_state);
-
-/* Function Name:
- *      rtk_vlan_checkAndCreateMbr
- * Description:
- *      Check and create Member configuration and return index
- * Input:
- *      vid  - VLAN id.
- * Output:
- *      pIndex  - Member configuration index
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_VLAN_VID     - Invalid VLAN ID.
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - VLAN not found
- *      RT_ERR_TBL_FULL     - Member Configuration table full
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_checkAndCreateMbr(rtk_vlan_t vid, rtk_uint32 *pIndex);
-
-/* Function Name:
- *      rtk_vlan_reservedVidAction_set
- * Description:
- *      Set Action of VLAN ID = 0 & 4095 tagged packet
- * Input:
- *      action_vid0     - Action for VID 0.
- *      action_vid4095  - Action for VID 4095.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_reservedVidAction_set(rtk_vlan_resVidAction_t action_vid0, rtk_vlan_resVidAction_t action_vid4095);
-
-/* Function Name:
- *      rtk_vlan_reservedVidAction_get
- * Description:
- *      Get Action of VLAN ID = 0 & 4095 tagged packet
- * Input:
- *      pAction_vid0     - Action for VID 0.
- *      pAction_vid4095  - Action for VID 4095.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - NULL Pointer
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_reservedVidAction_get(rtk_vlan_resVidAction_t *pAction_vid0, rtk_vlan_resVidAction_t *pAction_vid4095);
-
-/* Function Name:
- *      rtk_vlan_realKeepRemarkEnable_set
- * Description:
- *      Set Real keep 1p remarking feature
- * Input:
- *      enabled     - State of 1p remarking at real keep packet
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_realKeepRemarkEnable_set(rtk_enable_t enabled);
-
-/* Function Name:
- *      rtk_vlan_realKeepRemarkEnable_get
- * Description:
- *      Get Real keep 1p remarking feature
- * Input:
- *      None.
- * Output:
- *      pEnabled     - State of 1p remarking at real keep packet
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-extern rtk_api_ret_t rtk_vlan_realKeepRemarkEnable_get(rtk_enable_t *pEnabled);
-
-/* Function Name:
- *      rtk_vlan_reset
- * Description:
- *      Reset VLAN
- * Input:
- *      None.
- * Output:
- *      pEnabled     - State of 1p remarking at real keep packet
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_reset(void);
-
-#endif /* __RTK_API_VLAN_H__ */
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/interrupt.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/interrupt.c
deleted file mode 100644
index 165ee41721..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/interrupt.c
+++ /dev/null
@@ -1,434 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in Interrupt module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <interrupt.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_interrupt.h>
-
-/* Function Name:
- *      rtk_int_polarity_set
- * Description:
- *      Set interrupt polarity configuration.
- * Input:
- *      type - Interruptpolarity type.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set interrupt polarity configuration.
- */
-rtk_api_ret_t rtk_int_polarity_set(rtk_int_polarity_t type)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(type >= INT_POLAR_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicInterruptPolarity(type)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_int_polarity_get
- * Description:
- *      Get interrupt polarity configuration.
- * Input:
- *      None
- * Output:
- *      pType - Interruptpolarity type.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API can get interrupt polarity configuration.
- */
-rtk_api_ret_t rtk_int_polarity_get(rtk_int_polarity_t *pType)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pType)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicInterruptPolarity(pType)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_int_control_set
- * Description:
- *      Set interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- *      enable - Interrupt status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The API can set interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS
- *      - INT_TYPE_METER_EXCEED
- *      - INT_TYPE_LEARN_LIMIT
- *      - INT_TYPE_LINK_SPEED
- *      - INT_TYPE_CONGEST
- *      - INT_TYPE_GREEN_FEATURE
- *      - INT_TYPE_LOOP_DETECT
- *      - INT_TYPE_8051,
- *      - INT_TYPE_CABLE_DIAG,
- *      - INT_TYPE_ACL,
- *      - INT_TYPE_SLIENT
- */
-rtk_api_ret_t rtk_int_control_set(rtk_int_type_t type, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 mask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= INT_TYPE_END)
-        return RT_ERR_INPUT;
-
-    if (type == INT_TYPE_RESERVED)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_getAsicInterruptMask(&mask)) != RT_ERR_OK)
-        return retVal;
-
-    if (ENABLED == enable)
-        mask = mask | (1<<type);
-    else if (DISABLED == enable)
-        mask = mask & ~(1<<type);
-    else
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicInterruptMask(mask)) != RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_int_control_get
- * Description:
- *      Get interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- * Output:
- *      pEnable - Interrupt status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS
- *      - INT_TYPE_METER_EXCEED
- *      - INT_TYPE_LEARN_LIMIT
- *      - INT_TYPE_LINK_SPEED
- *      - INT_TYPE_CONGEST
- *      - INT_TYPE_GREEN_FEATURE
- *      - INT_TYPE_LOOP_DETECT
- *      - INT_TYPE_8051,
- *      - INT_TYPE_CABLE_DIAG,
- *      - INT_TYPE_ACL,
- *      - INT_TYPE_UPS,
- *      - INT_TYPE_SLIENT
- */
-rtk_api_ret_t rtk_int_control_get(rtk_int_type_t type, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 mask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicInterruptMask(&mask)) != RT_ERR_OK)
-        return retVal;
-
-    if (0 == (mask&(1<<type)))
-        *pEnable=DISABLED;
-    else
-        *pEnable=ENABLED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_int_status_set
- * Description:
- *      Set interrupt trigger status to clean.
- * Input:
- *      None
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- * Note:
- *      The API can clean interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS    (value[0] (Bit0))
- *      - INT_TYPE_METER_EXCEED   (value[0] (Bit1))
- *      - INT_TYPE_LEARN_LIMIT    (value[0] (Bit2))
- *      - INT_TYPE_LINK_SPEED     (value[0] (Bit3))
- *      - INT_TYPE_CONGEST        (value[0] (Bit4))
- *      - INT_TYPE_GREEN_FEATURE  (value[0] (Bit5))
- *      - INT_TYPE_LOOP_DETECT    (value[0] (Bit6))
- *      - INT_TYPE_8051           (value[0] (Bit7))
- *      - INT_TYPE_CABLE_DIAG     (value[0] (Bit8))
- *      - INT_TYPE_ACL            (value[0] (Bit9))
- *      - INT_TYPE_SLIENT         (value[0] (Bit11))
- *      The status will be cleared after execute this API.
- */
-rtk_api_ret_t rtk_int_status_set(rtk_int_status_t *pStatusMask)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pStatusMask)
-        return RT_ERR_NULL_POINTER;
-
-    if(pStatusMask->value[0] & (0x0001 << INT_TYPE_RESERVED))
-        return RT_ERR_INPUT;
-
-    if(pStatusMask->value[0] >= (0x0001 << INT_TYPE_END))
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicInterruptStatus((rtk_uint32)pStatusMask->value[0]))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_int_status_get
- * Description:
- *      Get interrupt trigger status.
- * Input:
- *      None
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - INT_TYPE_LINK_STATUS    (value[0] (Bit0))
- *      - INT_TYPE_METER_EXCEED   (value[0] (Bit1))
- *      - INT_TYPE_LEARN_LIMIT    (value[0] (Bit2))
- *      - INT_TYPE_LINK_SPEED     (value[0] (Bit3))
- *      - INT_TYPE_CONGEST        (value[0] (Bit4))
- *      - INT_TYPE_GREEN_FEATURE  (value[0] (Bit5))
- *      - INT_TYPE_LOOP_DETECT    (value[0] (Bit6))
- *      - INT_TYPE_8051           (value[0] (Bit7))
- *      - INT_TYPE_CABLE_DIAG     (value[0] (Bit8))
- *      - INT_TYPE_ACL            (value[0] (Bit9))
- *      - INT_TYPE_SLIENT         (value[0] (Bit11))
- *
- */
-rtk_api_ret_t rtk_int_status_get(rtk_int_status_t* pStatusMask)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32          ims_mask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pStatusMask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicInterruptStatus(&ims_mask)) != RT_ERR_OK)
-        return retVal;
-
-    pStatusMask->value[0] = (ims_mask & 0x00000FFF);
-    return RT_ERR_OK;
-}
-
-#define ADV_NOT_SUPPORT (0xFFFF)
-static rtk_api_ret_t _rtk_int_Advidx_get(rtk_int_advType_t adv_type, rtk_uint32 *pAsic_idx)
-{
-    rtk_uint32 asic_idx[ADV_END] =
-    {
-        INTRST_L2_LEARN,
-        INTRST_SPEED_CHANGE,
-        INTRST_SPECIAL_CONGESTION,
-        INTRST_PORT_LINKDOWN,
-        INTRST_PORT_LINKUP,
-        ADV_NOT_SUPPORT,
-        INTRST_RLDP_LOOPED,
-        INTRST_RLDP_RELEASED,
-    };
-
-    if(adv_type >= ADV_END)
-        return RT_ERR_INPUT;
-
-    if(asic_idx[adv_type] == ADV_NOT_SUPPORT)
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    *pAsic_idx = asic_idx[adv_type];
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_int_advanceInfo_get
- * Description:
- *      Get interrupt advanced information.
- * Input:
- *      adv_type - Advanced interrupt type.
- * Output:
- *      info - Information per type.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get advanced information when interrupt happened.
- *      The status will be cleared after execute this API.
- */
-rtk_api_ret_t rtk_int_advanceInfo_get(rtk_int_advType_t adv_type, rtk_int_info_t *pInfo)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      data;
-    rtk_uint32      intAdvType;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(adv_type >= ADV_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pInfo)
-        return RT_ERR_NULL_POINTER;
-
-    if(adv_type != ADV_METER_EXCEED_MASK)
-    {
-        if((retVal = _rtk_int_Advidx_get(adv_type, &intAdvType)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    switch(adv_type)
-    {
-        case ADV_L2_LEARN_PORT_MASK:
-            /* Get physical portmask */
-            if((retVal = rtl8367c_getAsicInterruptRelatedStatus(intAdvType, &data)) != RT_ERR_OK)
-                return retVal;
-
-            /* Clear Advanced Info */
-            if((retVal = rtl8367c_setAsicInterruptRelatedStatus(intAdvType, 0xFFFF)) != RT_ERR_OK)
-                return retVal;
-
-            /* Translate to logical portmask */
-            if((retVal = rtk_switch_portmask_P2L_get(data, &(pInfo->portMask))) != RT_ERR_OK)
-                return retVal;
-
-            /* Get system learn */
-            if((retVal = rtl8367c_getAsicInterruptRelatedStatus(INTRST_SYS_LEARN, &data)) != RT_ERR_OK)
-                return retVal;
-
-            /* Clear system learn */
-            if((retVal = rtl8367c_setAsicInterruptRelatedStatus(INTRST_SYS_LEARN, 0x0001)) != RT_ERR_OK)
-                return retVal;
-
-            pInfo->systemLearnOver = data;
-            break;
-        case ADV_SPEED_CHANGE_PORT_MASK:
-        case ADV_SPECIAL_CONGESTION_PORT_MASK:
-        case ADV_PORT_LINKDOWN_PORT_MASK:
-        case ADV_PORT_LINKUP_PORT_MASK:
-        case ADV_RLDP_LOOPED:
-        case ADV_RLDP_RELEASED:
-            /* Get physical portmask */
-            if((retVal = rtl8367c_getAsicInterruptRelatedStatus(intAdvType, &data)) != RT_ERR_OK)
-                return retVal;
-
-            /* Clear Advanced Info */
-            if((retVal = rtl8367c_setAsicInterruptRelatedStatus(intAdvType, 0xFFFF)) != RT_ERR_OK)
-                return retVal;
-
-            /* Translate to logical portmask */
-            if((retVal = rtk_switch_portmask_P2L_get(data, &(pInfo->portMask))) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case ADV_METER_EXCEED_MASK:
-            /* Get Meter Mask */
-            if((retVal = rtl8367c_getAsicInterruptRelatedStatus(INTRST_METER0_15, &data)) != RT_ERR_OK)
-                return retVal;
-
-            /* Clear Advanced Info */
-            if((retVal = rtl8367c_setAsicInterruptRelatedStatus(INTRST_METER0_15, 0xFFFF)) != RT_ERR_OK)
-                return retVal;
-
-            pInfo->meterMask = data & 0xFFFF;
-
-            /* Get Meter Mask */
-            if((retVal = rtl8367c_getAsicInterruptRelatedStatus(INTRST_METER16_31, &data)) != RT_ERR_OK)
-                return retVal;
-
-            /* Clear Advanced Info */
-            if((retVal = rtl8367c_setAsicInterruptRelatedStatus(INTRST_METER16_31, 0xFFFF)) != RT_ERR_OK)
-                return retVal;
-
-            pInfo->meterMask = pInfo->meterMask | ((data << 16) & 0xFFFF0000);
-
-            break;
-        default:
-            return RT_ERR_INPUT;
-    }
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/l2.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/l2.c
deleted file mode 100644
index feff0b240b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/l2.c
+++ /dev/null
@@ -1,2911 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in L2 module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <l2.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_lut.h>
-#include <rtl8367c_asicdrv_port.h>
-
-/* Function Name:
- *      rtk_l2_init
- * Description:
- *      Initialize l2 module of the specified device.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      Initialize l2 module before calling any l2 APIs.
- */
-rtk_api_ret_t rtk_l2_init(void)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_setAsicLutIpMulticastLookup(DISABLED)) != RT_ERR_OK)
-        return retVal;
-
-    /*Enable CAM Usage*/
-    if ((retVal = rtl8367c_setAsicLutCamTbUsage(ENABLED)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicLutAgeTimerSpeed(6,2)) != RT_ERR_OK)
-        return retVal;
-
-    RTK_SCAN_ALL_LOG_PORT(port)
-    {
-        if ((retVal = rtl8367c_setAsicLutLearnLimitNo(rtk_switch_port_L2P_get(port), rtk_switch_maxLutAddrNumber_get())) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_l2_addr_add
- * Description:
- *      Add LUT unicast entry.
- * Input:
- *      pMac - 6 bytes unicast(I/G bit is 0) mac address to be written into LUT.
- *      pL2_data - Unicast entry parameter
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_MAC              - Invalid MAC address.
- *      RT_ERR_L2_FID           - Invalid FID .
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      If the unicast mac address already existed in LUT, it will udpate the status of the entry.
- *      Otherwise, it will find an empty or asic auto learned entry to write. If all the entries
- *      with the same hash value can't be replaced, ASIC will return a RT_ERR_L2_INDEXTBL_FULL error.
- */
-rtk_api_ret_t rtk_l2_addr_add(rtk_mac_t *pMac, rtk_l2_ucastAddr_t *pL2_data)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* must be unicast address */
-    if ((pMac == NULL) || (pMac->octet[0] & 0x1))
-        return RT_ERR_MAC;
-
-    if(pL2_data == NULL)
-        return RT_ERR_MAC;
-
-    RTK_CHK_PORT_VALID(pL2_data->port);
-
-    if (pL2_data->ivl >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->cvid > RTL8367C_VIDMAX)
-        return RT_ERR_L2_VID;
-
-    if (pL2_data->fid > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    if (pL2_data->is_static>= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->sa_block>= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->da_block>= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->auth>= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->efid> RTL8367C_EFIDMAX)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->priority > RTL8367C_PRIMAX)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->sa_pri_en >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (pL2_data->fwd_pri_en >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-
-    /* fill key (MAC,FID) to get L2 entry */
-    memcpy(l2Table.mac.octet, pMac->octet, ETHER_ADDR_LEN);
-    l2Table.ivl_svl     = pL2_data->ivl;
-    l2Table.fid         = pL2_data->fid;
-    l2Table.cvid_fid    = pL2_data->cvid;
-    l2Table.efid        = pL2_data->efid;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal )
-    {
-        memcpy(l2Table.mac.octet, pMac->octet, ETHER_ADDR_LEN);
-        l2Table.ivl_svl     = pL2_data->ivl;
-        l2Table.cvid_fid    = pL2_data->cvid;
-        l2Table.fid         = pL2_data->fid;
-        l2Table.efid        = pL2_data->efid;
-        l2Table.spa         = rtk_switch_port_L2P_get(pL2_data->port);
-        l2Table.nosalearn   = pL2_data->is_static;
-        l2Table.sa_block    = pL2_data->sa_block;
-        l2Table.da_block    = pL2_data->da_block;
-        l2Table.l3lookup    = 0;
-        l2Table.auth        = pL2_data->auth;
-        l2Table.age         = 6;
-        l2Table.lut_pri     = pL2_data->priority;
-        l2Table.sa_en       = pL2_data->sa_pri_en;
-        l2Table.fwd_en      = pL2_data->fwd_pri_en;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pL2_data->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else if (RT_ERR_L2_ENTRY_NOTFOUND == retVal )
-    {
-        memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-        memcpy(l2Table.mac.octet, pMac->octet, ETHER_ADDR_LEN);
-        l2Table.ivl_svl     = pL2_data->ivl;
-        l2Table.cvid_fid    = pL2_data->cvid;
-        l2Table.fid         = pL2_data->fid;
-        l2Table.efid        = pL2_data->efid;
-        l2Table.spa         = rtk_switch_port_L2P_get(pL2_data->port);
-        l2Table.nosalearn   = pL2_data->is_static;
-        l2Table.sa_block    = pL2_data->sa_block;
-        l2Table.da_block    = pL2_data->da_block;
-        l2Table.l3lookup    = 0;
-        l2Table.auth        = pL2_data->auth;
-        l2Table.age         = 6;
-        l2Table.lut_pri     = pL2_data->priority;
-        l2Table.sa_en       = pL2_data->sa_pri_en;
-        l2Table.fwd_en      = pL2_data->fwd_pri_en;
-
-        if ((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pL2_data->address = l2Table.address;
-
-        method = LUTREADMETHOD_MAC;
-        retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-        if (RT_ERR_L2_ENTRY_NOTFOUND == retVal )
-            return RT_ERR_L2_INDEXTBL_FULL;
-        else
-            return retVal;
-    }
-    else
-        return retVal;
-
-}
-
-/* Function Name:
- *      rtk_l2_addr_get
- * Description:
- *      Get LUT unicast entry.
- * Input:
- *      pMac    - 6 bytes unicast(I/G bit is 0) mac address to be written into LUT.
- * Output:
- *      pL2_data - Unicast entry parameter
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the unicast mac address existed in LUT, it will return the port and fid where
- *      the mac is learned. Otherwise, it will return a RT_ERR_L2_ENTRY_NOTFOUND error.
- */
-rtk_api_ret_t rtk_l2_addr_get(rtk_mac_t *pMac, rtk_l2_ucastAddr_t *pL2_data)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* must be unicast address */
-    if ((pMac == NULL) || (pMac->octet[0] & 0x1))
-        return RT_ERR_MAC;
-
-    if (pL2_data->fid > RTL8367C_FIDMAX || pL2_data->efid > RTL8367C_EFIDMAX)
-        return RT_ERR_L2_FID;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-
-    memcpy(l2Table.mac.octet, pMac->octet, ETHER_ADDR_LEN);
-    l2Table.ivl_svl     = pL2_data->ivl;
-    l2Table.cvid_fid    = pL2_data->cvid;
-    l2Table.fid         = pL2_data->fid;
-    l2Table.efid        = pL2_data->efid;
-    method = LUTREADMETHOD_MAC;
-
-    if ((retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table)) != RT_ERR_OK)
-        return retVal;
-
-    memcpy(pL2_data->mac.octet, pMac->octet,ETHER_ADDR_LEN);
-    pL2_data->port      = rtk_switch_port_P2L_get(l2Table.spa);
-    pL2_data->fid       = l2Table.fid;
-    pL2_data->efid      = l2Table.efid;
-    pL2_data->ivl       = l2Table.ivl_svl;
-    pL2_data->cvid      = l2Table.cvid_fid;
-    pL2_data->is_static = l2Table.nosalearn;
-    pL2_data->auth      = l2Table.auth;
-    pL2_data->sa_block  = l2Table.sa_block;
-    pL2_data->da_block  = l2Table.da_block;
-    pL2_data->priority  = l2Table.lut_pri;
-    pL2_data->sa_pri_en = l2Table.sa_en;
-    pL2_data->fwd_pri_en= l2Table.fwd_en;
-    pL2_data->address   = l2Table.address;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_addr_next_get
- * Description:
- *      Get Next LUT unicast entry.
- * Input:
- *      read_method     - The reading method.
- *      port            - The port number if the read_metohd is READMETHOD_NEXT_L2UCSPA
- *      pAddress        - The Address ID
- * Output:
- *      pL2_data - Unicast entry parameter
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next unicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all entries is LUT.
- */
-rtk_api_ret_t rtk_l2_addr_next_get(rtk_l2_read_method_t read_method, rtk_port_t port, rtk_uint32 *pAddress, rtk_l2_ucastAddr_t *pL2_data)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      method;
-    rtl8367c_luttb  l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Error Checking */
-    if ((pL2_data == NULL) || (pAddress == NULL))
-        return RT_ERR_MAC;
-
-    if(read_method == READMETHOD_NEXT_L2UC)
-        method = LUTREADMETHOD_NEXT_L2UC;
-    else if(read_method == READMETHOD_NEXT_L2UCSPA)
-        method = LUTREADMETHOD_NEXT_L2UCSPA;
-    else
-        return RT_ERR_INPUT;
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(*pAddress > RTK_MAX_LUT_ADDR_ID )
-        return RT_ERR_L2_L2UNI_PARAM;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-    l2Table.address = *pAddress;
-
-    if(read_method == READMETHOD_NEXT_L2UCSPA)
-        l2Table.spa = rtk_switch_port_L2P_get(port);
-
-    if ((retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table)) != RT_ERR_OK)
-        return retVal;
-
-    if(l2Table.address < *pAddress)
-        return RT_ERR_L2_ENTRY_NOTFOUND;
-
-    memcpy(pL2_data->mac.octet, l2Table.mac.octet, ETHER_ADDR_LEN);
-    pL2_data->port      = rtk_switch_port_P2L_get(l2Table.spa);
-    pL2_data->fid       = l2Table.fid;
-    pL2_data->efid      = l2Table.efid;
-    pL2_data->ivl       = l2Table.ivl_svl;
-    pL2_data->cvid      = l2Table.cvid_fid;
-    pL2_data->is_static = l2Table.nosalearn;
-    pL2_data->auth      = l2Table.auth;
-    pL2_data->sa_block  = l2Table.sa_block;
-    pL2_data->da_block  = l2Table.da_block;
-    pL2_data->priority  = l2Table.lut_pri;
-    pL2_data->sa_pri_en = l2Table.sa_en;
-    pL2_data->fwd_pri_en= l2Table.fwd_en;
-    pL2_data->address   = l2Table.address;
-
-    *pAddress = l2Table.address;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_l2_addr_del
- * Description:
- *      Delete LUT unicast entry.
- * Input:
- *      pMac - 6 bytes unicast(I/G bit is 0) mac address to be written into LUT.
- *      fid - Filtering database
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the mac has existed in the LUT, it will be deleted. Otherwise, it will return RT_ERR_L2_ENTRY_NOTFOUND.
- */
-rtk_api_ret_t rtk_l2_addr_del(rtk_mac_t *pMac, rtk_l2_ucastAddr_t *pL2_data)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* must be unicast address */
-    if ((pMac == NULL) || (pMac->octet[0] & 0x1))
-        return RT_ERR_MAC;
-
-    if (pL2_data->fid > RTL8367C_FIDMAX || pL2_data->efid > RTL8367C_EFIDMAX)
-        return RT_ERR_L2_FID;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-
-    /* fill key (MAC,FID) to get L2 entry */
-    memcpy(l2Table.mac.octet, pMac->octet, ETHER_ADDR_LEN);
-    l2Table.ivl_svl     = pL2_data->ivl;
-    l2Table.cvid_fid    = pL2_data->cvid;
-    l2Table.fid         = pL2_data->fid;
-    l2Table.efid        = pL2_data->efid;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK ==  retVal)
-    {
-        memcpy(l2Table.mac.octet, pMac->octet, ETHER_ADDR_LEN);
-        l2Table.ivl_svl     = pL2_data->ivl;
-        l2Table.cvid_fid    = pL2_data->cvid;
-        l2Table.fid = pL2_data->fid;
-        l2Table.efid = pL2_data->efid;
-        l2Table.spa = 0;
-        l2Table.nosalearn = 0;
-        l2Table.sa_block = 0;
-        l2Table.da_block = 0;
-        l2Table.auth = 0;
-        l2Table.age = 0;
-        l2Table.lut_pri = 0;
-        l2Table.sa_en = 0;
-        l2Table.fwd_en = 0;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pL2_data->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else
-        return retVal;
-}
-
-/* Function Name:
- *      rtk_l2_mcastAddr_add
- * Description:
- *      Add LUT multicast entry.
- * Input:
- *      pMcastAddr  - L2 multicast entry structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_MAC              - Invalid MAC address.
- *      RT_ERR_L2_FID           - Invalid FID .
- *      RT_ERR_L2_VID           - Invalid VID .
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      If the multicast mac address already existed in the LUT, it will udpate the
- *      port mask of the entry. Otherwise, it will find an empty or asic auto learned
- *      entry to write. If all the entries with the same hash value can't be replaced,
- *      ASIC will return a RT_ERR_L2_INDEXTBL_FULL error.
- */
-rtk_api_ret_t rtk_l2_mcastAddr_add(rtk_l2_mcastAddr_t *pMcastAddr)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      method;
-    rtl8367c_luttb  l2Table;
-    rtk_uint32      pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    /* must be L2 multicast address */
-    if( (pMcastAddr->mac.octet[0] & 0x01) != 0x01)
-        return RT_ERR_MAC;
-
-    RTK_CHK_PORTMASK_VALID(&pMcastAddr->portmask);
-
-    if(pMcastAddr->ivl == 1)
-    {
-        if (pMcastAddr->vid > RTL8367C_VIDMAX)
-            return RT_ERR_L2_VID;
-    }
-    else if(pMcastAddr->ivl == 0)
-    {
-        if (pMcastAddr->fid > RTL8367C_FIDMAX)
-            return RT_ERR_L2_FID;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    if(pMcastAddr->fwd_pri_en >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(pMcastAddr->priority > RTL8367C_PRIMAX)
-        return RT_ERR_INPUT;
-
-    /* Get physical port mask */
-    if ((retVal = rtk_switch_portmask_L2P_get(&pMcastAddr->portmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-
-    /* fill key (MAC,FID) to get L2 entry */
-    memcpy(l2Table.mac.octet, pMcastAddr->mac.octet, ETHER_ADDR_LEN);
-    l2Table.ivl_svl     = pMcastAddr->ivl;
-
-    if(pMcastAddr->ivl)
-        l2Table.cvid_fid    = pMcastAddr->vid;
-    else
-        l2Table.cvid_fid    = pMcastAddr->fid;
-
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal)
-    {
-        memcpy(l2Table.mac.octet, pMcastAddr->mac.octet, ETHER_ADDR_LEN);
-        l2Table.ivl_svl     = pMcastAddr->ivl;
-
-        if(pMcastAddr->ivl)
-            l2Table.cvid_fid    = pMcastAddr->vid;
-        else
-            l2Table.cvid_fid    = pMcastAddr->fid;
-
-        l2Table.mbr         = pmask;
-        l2Table.nosalearn   = 1;
-        l2Table.l3lookup    = 0;
-        l2Table.lut_pri     = pMcastAddr->priority;
-        l2Table.fwd_en      = pMcastAddr->fwd_pri_en;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pMcastAddr->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else if (RT_ERR_L2_ENTRY_NOTFOUND == retVal)
-    {
-        memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-        memcpy(l2Table.mac.octet, pMcastAddr->mac.octet, ETHER_ADDR_LEN);
-        l2Table.ivl_svl     = pMcastAddr->ivl;
-        if(pMcastAddr->ivl)
-            l2Table.cvid_fid    = pMcastAddr->vid;
-        else
-            l2Table.cvid_fid    = pMcastAddr->fid;
-
-        l2Table.mbr         = pmask;
-        l2Table.nosalearn   = 1;
-        l2Table.l3lookup    = 0;
-        l2Table.lut_pri     = pMcastAddr->priority;
-        l2Table.fwd_en      = pMcastAddr->fwd_pri_en;
-        if ((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pMcastAddr->address = l2Table.address;
-
-        method = LUTREADMETHOD_MAC;
-        retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-        if (RT_ERR_L2_ENTRY_NOTFOUND == retVal)
-            return     RT_ERR_L2_INDEXTBL_FULL;
-        else
-            return retVal;
-    }
-    else
-        return retVal;
-
-}
-
-/* Function Name:
- *      rtk_l2_mcastAddr_get
- * Description:
- *      Get LUT multicast entry.
- * Input:
- *      pMcastAddr  - L2 multicast entry structure
- * Output:
- *      pMcastAddr  - L2 multicast entry structure
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_VID               - Invalid VID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the multicast mac address existed in the LUT, it will return the port where
- *      the mac is learned. Otherwise, it will return a RT_ERR_L2_ENTRY_NOTFOUND error.
- */
-rtk_api_ret_t rtk_l2_mcastAddr_get(rtk_l2_mcastAddr_t *pMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    /* must be L2 multicast address */
-    if( (pMcastAddr->mac.octet[0] & 0x01) != 0x01)
-        return RT_ERR_MAC;
-
-    if(pMcastAddr->ivl == 1)
-    {
-        if (pMcastAddr->vid > RTL8367C_VIDMAX)
-            return RT_ERR_L2_VID;
-    }
-    else if(pMcastAddr->ivl == 0)
-    {
-        if (pMcastAddr->fid > RTL8367C_FIDMAX)
-            return RT_ERR_L2_FID;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-    memcpy(l2Table.mac.octet, pMcastAddr->mac.octet, ETHER_ADDR_LEN);
-    l2Table.ivl_svl     = pMcastAddr->ivl;
-
-    if(pMcastAddr->ivl)
-        l2Table.cvid_fid    = pMcastAddr->vid;
-    else
-        l2Table.cvid_fid    = pMcastAddr->fid;
-
-    method = LUTREADMETHOD_MAC;
-
-    if ((retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table)) != RT_ERR_OK)
-        return retVal;
-
-    pMcastAddr->priority    = l2Table.lut_pri;
-    pMcastAddr->fwd_pri_en  = l2Table.fwd_en;
-    pMcastAddr->igmp_asic   = l2Table.igmp_asic;
-    pMcastAddr->igmp_index  = l2Table.igmpidx;
-    pMcastAddr->address     = l2Table.address;
-
-    /* Get Logical port mask */
-    if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &pMcastAddr->portmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_mcastAddr_next_get
- * Description:
- *      Get Next L2 Multicast entry.
- * Input:
- *      pAddress        - The Address ID
- * Output:
- *      pMcastAddr  - L2 multicast entry structure
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next L2 multicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all multicast entries is LUT.
- */
-rtk_api_ret_t rtk_l2_mcastAddr_next_get(rtk_uint32 *pAddress, rtk_l2_mcastAddr_t *pMcastAddr)
-{
-    rtk_api_ret_t   retVal;
-    rtl8367c_luttb  l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Error Checking */
-    if ((pAddress == NULL) || (pMcastAddr == NULL))
-        return RT_ERR_INPUT;
-
-    if(*pAddress > RTK_MAX_LUT_ADDR_ID )
-        return RT_ERR_L2_L2UNI_PARAM;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-    l2Table.address = *pAddress;
-
-    if ((retVal = rtl8367c_getAsicL2LookupTb(LUTREADMETHOD_NEXT_L2MC, &l2Table)) != RT_ERR_OK)
-        return retVal;
-
-    if(l2Table.address < *pAddress)
-        return RT_ERR_L2_ENTRY_NOTFOUND;
-
-    memcpy(pMcastAddr->mac.octet, l2Table.mac.octet, ETHER_ADDR_LEN);
-    pMcastAddr->ivl     = l2Table.ivl_svl;
-
-    if(pMcastAddr->ivl)
-        pMcastAddr->vid = l2Table.cvid_fid;
-    else
-        pMcastAddr->fid = l2Table.cvid_fid;
-
-    pMcastAddr->priority    = l2Table.lut_pri;
-    pMcastAddr->fwd_pri_en  = l2Table.fwd_en;
-    pMcastAddr->igmp_asic   = l2Table.igmp_asic;
-    pMcastAddr->igmp_index  = l2Table.igmpidx;
-    pMcastAddr->address     = l2Table.address;
-
-    /* Get Logical port mask */
-    if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &pMcastAddr->portmask)) != RT_ERR_OK)
-        return retVal;
-
-    *pAddress = l2Table.address;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_mcastAddr_del
- * Description:
- *      Delete LUT multicast entry.
- * Input:
- *      pMcastAddr  - L2 multicast entry structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_MAC                  - Invalid MAC address.
- *      RT_ERR_L2_FID               - Invalid FID .
- *      RT_ERR_L2_VID               - Invalid VID .
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      If the mac has existed in the LUT, it will be deleted. Otherwise, it will return RT_ERR_L2_ENTRY_NOTFOUND.
- */
-rtk_api_ret_t rtk_l2_mcastAddr_del(rtk_l2_mcastAddr_t *pMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    /* must be L2 multicast address */
-    if( (pMcastAddr->mac.octet[0] & 0x01) != 0x01)
-        return RT_ERR_MAC;
-
-    if(pMcastAddr->ivl == 1)
-    {
-        if (pMcastAddr->vid > RTL8367C_VIDMAX)
-            return RT_ERR_L2_VID;
-    }
-    else if(pMcastAddr->ivl == 0)
-    {
-        if (pMcastAddr->fid > RTL8367C_FIDMAX)
-            return RT_ERR_L2_FID;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-
-    /* fill key (MAC,FID) to get L2 entry */
-    memcpy(l2Table.mac.octet, pMcastAddr->mac.octet, ETHER_ADDR_LEN);
-    l2Table.ivl_svl     = pMcastAddr->ivl;
-
-    if(pMcastAddr->ivl)
-        l2Table.cvid_fid    = pMcastAddr->vid;
-    else
-        l2Table.cvid_fid    = pMcastAddr->fid;
-
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal)
-    {
-        memcpy(l2Table.mac.octet, pMcastAddr->mac.octet, ETHER_ADDR_LEN);
-        l2Table.ivl_svl     = pMcastAddr->ivl;
-
-        if(pMcastAddr->ivl)
-            l2Table.cvid_fid    = pMcastAddr->vid;
-        else
-            l2Table.cvid_fid    = pMcastAddr->fid;
-
-        l2Table.mbr         = 0;
-        l2Table.nosalearn   = 0;
-        l2Table.sa_block    = 0;
-        l2Table.l3lookup    = 0;
-        l2Table.lut_pri     = 0;
-        l2Table.fwd_en      = 0;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pMcastAddr->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else
-        return retVal;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_add
- * Description:
- *      Add Lut IP multicast entry
- * Input:
- *      pIpMcastAddr    - IP Multicast entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      System supports L2 entry with IP multicast DIP/SIP to forward IP multicasting frame as user
- *      desired. If this function is enabled, then system will be looked up L2 IP multicast entry to
- *      forward IP multicast frame directly without flooding.
- */
-rtk_api_ret_t rtk_l2_ipMcastAddr_add(rtk_l2_ipMcastAddr_t *pIpMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pIpMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    /* check port mask */
-    RTK_CHK_PORTMASK_VALID(&pIpMcastAddr->portmask);
-
-    if( (pIpMcastAddr->dip & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    if(pIpMcastAddr->fwd_pri_en >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pIpMcastAddr->priority > RTL8367C_PRIMAX)
-        return RT_ERR_INPUT;
-
-    /* Get Physical port mask */
-    if ((retVal = rtk_switch_portmask_L2P_get(&pIpMcastAddr->portmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    memset(&l2Table, 0x00, sizeof(rtl8367c_luttb));
-    l2Table.sip = pIpMcastAddr->sip;
-    l2Table.dip = pIpMcastAddr->dip;
-    l2Table.l3lookup = 1;
-    l2Table.l3vidlookup = 0;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal)
-    {
-        l2Table.sip = pIpMcastAddr->sip;
-        l2Table.dip = pIpMcastAddr->dip;
-        l2Table.mbr = pmask;
-        l2Table.nosalearn = 1;
-        l2Table.l3lookup = 1;
-        l2Table.l3vidlookup = 0;
-        l2Table.lut_pri = pIpMcastAddr->priority;
-        l2Table.fwd_en  = pIpMcastAddr->fwd_pri_en;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pIpMcastAddr->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else if (RT_ERR_L2_ENTRY_NOTFOUND == retVal)
-    {
-        memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-        l2Table.sip = pIpMcastAddr->sip;
-        l2Table.dip = pIpMcastAddr->dip;
-        l2Table.mbr = pmask;
-        l2Table.nosalearn = 1;
-        l2Table.l3lookup = 1;
-        l2Table.l3vidlookup = 0;
-        l2Table.lut_pri = pIpMcastAddr->priority;
-        l2Table.fwd_en  = pIpMcastAddr->fwd_pri_en;
-        if ((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pIpMcastAddr->address = l2Table.address;
-
-        method = LUTREADMETHOD_MAC;
-        retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-        if (RT_ERR_L2_ENTRY_NOTFOUND == retVal)
-            return     RT_ERR_L2_INDEXTBL_FULL;
-        else
-            return retVal;
-
-    }
-    else
-        return retVal;
-
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_get
- * Description:
- *      Get LUT IP multicast entry.
- * Input:
- *      pIpMcastAddr    - IP Multicast entry
- * Output:
- *      pIpMcastAddr    - IP Multicast entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      The API can get Lut table of IP multicast entry.
- */
-rtk_api_ret_t rtk_l2_ipMcastAddr_get(rtk_l2_ipMcastAddr_t *pIpMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pIpMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    if( (pIpMcastAddr->dip & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0x00, sizeof(rtl8367c_luttb));
-    l2Table.sip = pIpMcastAddr->sip;
-    l2Table.dip = pIpMcastAddr->dip;
-    l2Table.l3lookup = 1;
-    l2Table.l3vidlookup = 0;
-    method = LUTREADMETHOD_MAC;
-    if ((retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table)) != RT_ERR_OK)
-        return retVal;
-
-    /* Get Logical port mask */
-    if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &pIpMcastAddr->portmask)) != RT_ERR_OK)
-        return retVal;
-
-    pIpMcastAddr->priority      = l2Table.lut_pri;
-    pIpMcastAddr->fwd_pri_en    = l2Table.fwd_en;
-    pIpMcastAddr->igmp_asic     = l2Table.igmp_asic;
-    pIpMcastAddr->igmp_index    = l2Table.igmpidx;
-    pIpMcastAddr->address       = l2Table.address;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_next_get
- * Description:
- *      Get Next IP Multicast entry.
- * Input:
- *      pAddress        - The Address ID
- * Output:
- *      pIpMcastAddr    - IP Multicast entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next IP multicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all IP multicast entries is LUT.
- */
-rtk_api_ret_t rtk_l2_ipMcastAddr_next_get(rtk_uint32 *pAddress, rtk_l2_ipMcastAddr_t *pIpMcastAddr)
-{
-    rtk_api_ret_t   retVal;
-    rtl8367c_luttb  l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Error Checking */
-    if ((pAddress == NULL) || (pIpMcastAddr == NULL) )
-        return RT_ERR_INPUT;
-
-    if(*pAddress > RTK_MAX_LUT_ADDR_ID )
-        return RT_ERR_L2_L2UNI_PARAM;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-    l2Table.address = *pAddress;
-
-    do
-    {
-        if ((retVal = rtl8367c_getAsicL2LookupTb(LUTREADMETHOD_NEXT_L3MC, &l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        if(l2Table.address < *pAddress)
-            return RT_ERR_L2_ENTRY_NOTFOUND;
-
-    }while(l2Table.l3vidlookup == 1);
-
-    pIpMcastAddr->sip = l2Table.sip;
-    pIpMcastAddr->dip = l2Table.dip;
-
-    /* Get Logical port mask */
-    if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &pIpMcastAddr->portmask)) != RT_ERR_OK)
-        return retVal;
-
-    pIpMcastAddr->priority      = l2Table.lut_pri;
-    pIpMcastAddr->fwd_pri_en    = l2Table.fwd_en;
-    pIpMcastAddr->igmp_asic     = l2Table.igmp_asic;
-    pIpMcastAddr->igmp_index    = l2Table.igmpidx;
-    pIpMcastAddr->address       = l2Table.address;
-    *pAddress = l2Table.address;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastAddr_del
- * Description:
- *      Delete a ip multicast address entry from the specified device.
- * Input:
- *      pIpMcastAddr    - IP Multicast entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      The API can delete a IP multicast address entry from the specified device.
- */
-rtk_api_ret_t rtk_l2_ipMcastAddr_del(rtk_l2_ipMcastAddr_t *pIpMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Error Checking */
-    if (pIpMcastAddr == NULL)
-        return RT_ERR_INPUT;
-
-    if( (pIpMcastAddr->dip & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0x00, sizeof(rtl8367c_luttb));
-    l2Table.sip = pIpMcastAddr->sip;
-    l2Table.dip = pIpMcastAddr->dip;
-    l2Table.l3lookup = 1;
-    l2Table.l3vidlookup = 0;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal)
-    {
-        l2Table.sip = pIpMcastAddr->sip;
-        l2Table.dip = pIpMcastAddr->dip;
-        l2Table.mbr = 0;
-        l2Table.nosalearn = 0;
-        l2Table.l3lookup = 1;
-        l2Table.l3vidlookup = 0;
-        l2Table.lut_pri = 0;
-        l2Table.fwd_en  = 0;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pIpMcastAddr->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else
-        return retVal;
-}
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_add
- * Description:
- *      Add Lut IP multicast+VID entry
- * Input:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_L2_INDEXTBL_FULL - hashed index is full of entries.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_ipVidMcastAddr_add(rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pIpVidMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    /* check port mask */
-    RTK_CHK_PORTMASK_VALID(&pIpVidMcastAddr->portmask);
-
-    if (pIpVidMcastAddr->vid > RTL8367C_VIDMAX)
-        return RT_ERR_L2_VID;
-
-    if( (pIpVidMcastAddr->dip & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    /* Get Physical port mask */
-    if ((retVal = rtk_switch_portmask_L2P_get(&pIpVidMcastAddr->portmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    memset(&l2Table, 0x00, sizeof(rtl8367c_luttb));
-    l2Table.sip = pIpVidMcastAddr->sip;
-    l2Table.dip = pIpVidMcastAddr->dip;
-    l2Table.l3lookup = 1;
-    l2Table.l3vidlookup = 1;
-    l2Table.l3_vid = pIpVidMcastAddr->vid;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal)
-    {
-        l2Table.sip = pIpVidMcastAddr->sip;
-        l2Table.dip = pIpVidMcastAddr->dip;
-        l2Table.mbr = pmask;
-        l2Table.nosalearn = 1;
-        l2Table.l3lookup = 1;
-        l2Table.l3vidlookup = 1;
-        l2Table.l3_vid = pIpVidMcastAddr->vid;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pIpVidMcastAddr->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else if (RT_ERR_L2_ENTRY_NOTFOUND == retVal)
-    {
-        memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-        l2Table.sip = pIpVidMcastAddr->sip;
-        l2Table.dip = pIpVidMcastAddr->dip;
-        l2Table.mbr = pmask;
-        l2Table.nosalearn = 1;
-        l2Table.l3lookup = 1;
-        l2Table.l3vidlookup = 1;
-        l2Table.l3_vid = pIpVidMcastAddr->vid;
-        if ((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pIpVidMcastAddr->address = l2Table.address;
-
-        method = LUTREADMETHOD_MAC;
-        retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-        if (RT_ERR_L2_ENTRY_NOTFOUND == retVal)
-            return     RT_ERR_L2_INDEXTBL_FULL;
-        else
-            return retVal;
-
-    }
-    else
-        return retVal;
-}
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_get
- * Description:
- *      Get LUT IP multicast+VID entry.
- * Input:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Output:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_ipVidMcastAddr_get(rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pIpVidMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    if (pIpVidMcastAddr->vid > RTL8367C_VIDMAX)
-        return RT_ERR_L2_VID;
-
-    if( (pIpVidMcastAddr->dip & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0x00, sizeof(rtl8367c_luttb));
-    l2Table.sip = pIpVidMcastAddr->sip;
-    l2Table.dip = pIpVidMcastAddr->dip;
-    l2Table.l3lookup = 1;
-    l2Table.l3vidlookup = 1;
-    l2Table.l3_vid = pIpVidMcastAddr->vid;
-    method = LUTREADMETHOD_MAC;
-    if ((retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table)) != RT_ERR_OK)
-        return retVal;
-
-    pIpVidMcastAddr->address = l2Table.address;
-
-     /* Get Logical port mask */
-    if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &pIpVidMcastAddr->portmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_next_get
- * Description:
- *      Get Next IP Multicast+VID entry.
- * Input:
- *      pAddress        - The Address ID
- * Output:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *      Get the next IP multicast entry after the current entry pointed by pAddress.
- *      The address of next entry is returned by pAddress. User can use (address + 1)
- *      as pAddress to call this API again for dumping all IP multicast entries is LUT.
- */
-rtk_api_ret_t rtk_l2_ipVidMcastAddr_next_get(rtk_uint32 *pAddress, rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr)
-{
-    rtk_api_ret_t   retVal;
-    rtl8367c_luttb  l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Error Checking */
-    if ((pAddress == NULL) || (pIpVidMcastAddr == NULL))
-        return RT_ERR_INPUT;
-
-    if(*pAddress > RTK_MAX_LUT_ADDR_ID )
-        return RT_ERR_L2_L2UNI_PARAM;
-
-    memset(&l2Table, 0, sizeof(rtl8367c_luttb));
-    l2Table.address = *pAddress;
-
-    do
-    {
-        if ((retVal = rtl8367c_getAsicL2LookupTb(LUTREADMETHOD_NEXT_L3MC, &l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        if(l2Table.address < *pAddress)
-            return RT_ERR_L2_ENTRY_NOTFOUND;
-
-    }while(l2Table.l3vidlookup == 0);
-
-    pIpVidMcastAddr->sip        = l2Table.sip;
-    pIpVidMcastAddr->dip        = l2Table.dip;
-    pIpVidMcastAddr->vid        = l2Table.l3_vid;
-    pIpVidMcastAddr->address    = l2Table.address;
-
-    /* Get Logical port mask */
-    if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &pIpVidMcastAddr->portmask)) != RT_ERR_OK)
-        return retVal;
-
-    *pAddress = l2Table.address;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipVidMcastAddr_del
- * Description:
- *      Delete a ip multicast+VID address entry from the specified device.
- * Input:
- *      pIpVidMcastAddr - IP & VID multicast Entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_L2_ENTRY_NOTFOUND    - No such LUT entry.
- *      RT_ERR_INPUT                - Invalid input parameters.
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_ipVidMcastAddr_del(rtk_l2_ipVidMcastAddr_t *pIpVidMcastAddr)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pIpVidMcastAddr)
-        return RT_ERR_NULL_POINTER;
-
-    if (pIpVidMcastAddr->vid > RTL8367C_VIDMAX)
-        return RT_ERR_L2_VID;
-
-    if( (pIpVidMcastAddr->dip & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0x00, sizeof(rtl8367c_luttb));
-    l2Table.sip = pIpVidMcastAddr->sip;
-    l2Table.dip = pIpVidMcastAddr->dip;
-    l2Table.l3lookup = 1;
-    l2Table.l3vidlookup = 1;
-    l2Table.l3_vid = pIpVidMcastAddr->vid;
-    method = LUTREADMETHOD_MAC;
-    retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table);
-    if (RT_ERR_OK == retVal)
-    {
-        l2Table.sip = pIpVidMcastAddr->sip;
-        l2Table.dip = pIpVidMcastAddr->dip;
-        l2Table.mbr= 0;
-        l2Table.nosalearn = 0;
-        l2Table.l3lookup = 1;
-        l2Table.l3vidlookup = 1;
-        l2Table.l3_vid = pIpVidMcastAddr->vid;
-        if((retVal = rtl8367c_setAsicL2LookupTb(&l2Table)) != RT_ERR_OK)
-            return retVal;
-
-        pIpVidMcastAddr->address = l2Table.address;
-        return RT_ERR_OK;
-    }
-    else
-        return retVal;
-}
-
-/* Function Name:
- *      rtk_l2_ucastAddr_flush
- * Description:
- *      Flush L2 mac address by type in the specified device (both dynamic and static).
- * Input:
- *      pConfig - flush configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      flushByVid          - 1: Flush by VID, 0: Don't flush by VID
- *      vid                 - VID (0 ~ 4095)
- *      flushByFid          - 1: Flush by FID, 0: Don't flush by FID
- *      fid                 - FID (0 ~ 15)
- *      flushByPort         - 1: Flush by Port, 0: Don't flush by Port
- *      port                - Port ID
- *      flushByMac          - Not Supported
- *      ucastAddr           - Not Supported
- *      flushStaticAddr     - 1: Flush both Static and Dynamic entries, 0: Flush only Dynamic entries
- *      flushAddrOnAllPorts - 1: Flush VID-matched entries at all ports, 0: Flush VID-matched entries per port.
- */
-rtk_api_ret_t rtk_l2_ucastAddr_flush(rtk_l2_flushCfg_t *pConfig)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(pConfig == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(pConfig->flushByVid >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pConfig->flushByFid >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pConfig->flushByPort >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pConfig->flushByMac >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pConfig->flushStaticAddr >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pConfig->flushAddrOnAllPorts >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pConfig->vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    if(pConfig->fid > RTL8367C_FIDMAX)
-        return RT_ERR_INPUT;
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(pConfig->port);
-
-    if(pConfig->flushByVid == ENABLED)
-    {
-        if ((retVal = rtl8367c_setAsicLutFlushMode(FLUSHMDOE_VID)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutFlushVid(pConfig->vid)) != RT_ERR_OK)
-                return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutFlushType((pConfig->flushStaticAddr == ENABLED) ? FLUSHTYPE_BOTH : FLUSHTYPE_DYNAMIC)) != RT_ERR_OK)
-            return retVal;
-
-        if(pConfig->flushAddrOnAllPorts == ENABLED)
-        {
-            if ((retVal = rtl8367c_setAsicLutForceFlush(RTL8367C_PORTMASK)) != RT_ERR_OK)
-                return retVal;
-        }
-        else if(pConfig->flushByPort == ENABLED)
-        {
-            if ((retVal = rtl8367c_setAsicLutForceFlush(1 << rtk_switch_port_L2P_get(pConfig->port))) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-            return RT_ERR_INPUT;
-    }
-    else if(pConfig->flushByFid == ENABLED)
-    {
-        if ((retVal = rtl8367c_setAsicLutFlushMode(FLUSHMDOE_FID)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutFlushFid(pConfig->fid)) != RT_ERR_OK)
-                return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutFlushType((pConfig->flushStaticAddr == ENABLED) ? FLUSHTYPE_BOTH : FLUSHTYPE_DYNAMIC)) != RT_ERR_OK)
-            return retVal;
-
-        if(pConfig->flushAddrOnAllPorts == ENABLED)
-        {
-            if ((retVal = rtl8367c_setAsicLutForceFlush(RTL8367C_PORTMASK)) != RT_ERR_OK)
-                return retVal;
-        }
-        else if(pConfig->flushByPort == ENABLED)
-        {
-            if ((retVal = rtl8367c_setAsicLutForceFlush(1 << rtk_switch_port_L2P_get(pConfig->port))) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-            return RT_ERR_INPUT;
-    }
-    else if(pConfig->flushByPort == ENABLED)
-    {
-        if ((retVal = rtl8367c_setAsicLutFlushType((pConfig->flushStaticAddr == ENABLED) ? FLUSHTYPE_BOTH : FLUSHTYPE_DYNAMIC)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutFlushMode(FLUSHMDOE_PORT)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutForceFlush(1 << rtk_switch_port_L2P_get(pConfig->port))) != RT_ERR_OK)
-            return retVal;
-    }
-    else if(pConfig->flushByMac == ENABLED)
-    {
-        /* Should use API "rtk_l2_addr_del" to remove a specified entry*/
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_table_clear
- * Description:
- *      Flush all static & dynamic entries in LUT.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_table_clear(void)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_setAsicLutFlushAll()) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_table_clearStatus_get
- * Description:
- *      Get table clear status
- * Input:
- *      None
- * Output:
- *      pStatus - Clear status, 1:Busy, 0:finish
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_table_clearStatus_get(rtk_l2_clearStatus_t *pStatus)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pStatus)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLutFlushAllStatus((rtk_uint32 *)pStatus)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_flushLinkDownPortAddrEnable_set
- * Description:
- *      Set HW flush linkdown port mac configuration of the specified device.
- * Input:
- *      port - Port id.
- *      enable - link down flush status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The status of flush linkdown port address is as following:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_l2_flushLinkDownPortAddrEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicLutLinkDownForceAging(enable)) != RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_flushLinkDownPortAddrEnable_get
- * Description:
- *      Get HW flush linkdown port mac configuration of the specified device.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - link down flush status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The status of flush linkdown port address is as following:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_l2_flushLinkDownPortAddrEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLutLinkDownForceAging(pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_agingEnable_set
- * Description:
- *      Set L2 LUT aging status per port setting.
- * Input:
- *      port    - Port id.
- *      enable  - Aging status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can be used to set L2 LUT aging status per port.
- */
-rtk_api_ret_t rtk_l2_agingEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(enable == 1)
-        enable = 0;
-    else
-        enable = 1;
-
-    if ((retVal = rtl8367c_setAsicLutDisableAging(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_agingEnable_get
- * Description:
- *      Get L2 LUT aging status per port setting.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Aging status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can be used to get L2 LUT aging function per port.
- */
-rtk_api_ret_t rtk_l2_agingEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLutDisableAging(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    if(*pEnable == 1)
-        *pEnable = 0;
-    else
-        *pEnable = 1;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitLearningCnt_set
- * Description:
- *      Set per-Port auto learning limit number
- * Input:
- *      port    - Port id.
- *      mac_cnt - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_LIMITED_L2ENTRY_NUM  - Invalid auto learning limit number
- * Note:
- *      The API can set per-port ASIC auto learning limit number from 0(disable learning)
- *      to 2112.
- */
-rtk_api_ret_t rtk_l2_limitLearningCnt_set(rtk_port_t port, rtk_mac_cnt_t mac_cnt)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (mac_cnt > rtk_switch_maxLutAddrNumber_get())
-        return RT_ERR_LIMITED_L2ENTRY_NUM;
-
-    if ((retVal = rtl8367c_setAsicLutLearnLimitNo(rtk_switch_port_L2P_get(port), mac_cnt)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitLearningCnt_get
- * Description:
- *      Get per-Port auto learning limit number
- * Input:
- *      port - Port id.
- * Output:
- *      pMac_cnt - Auto learning entries limit number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get per-port ASIC auto learning limit number.
- */
-rtk_api_ret_t rtk_l2_limitLearningCnt_get(rtk_port_t port, rtk_mac_cnt_t *pMac_cnt)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pMac_cnt)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLutLearnLimitNo(rtk_switch_port_L2P_get(port), pMac_cnt)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCnt_set
- * Description:
- *      Set System auto learning limit number
- * Input:
- *      mac_cnt - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_LIMITED_L2ENTRY_NUM  - Invalid auto learning limit number
- * Note:
- *      The API can set system ASIC auto learning limit number from 0(disable learning)
- *      to 2112.
- */
-rtk_api_ret_t rtk_l2_limitSystemLearningCnt_set(rtk_mac_cnt_t mac_cnt)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (mac_cnt > rtk_switch_maxLutAddrNumber_get())
-        return RT_ERR_LIMITED_L2ENTRY_NUM;
-
-    if ((retVal = rtl8367c_setAsicSystemLutLearnLimitNo(mac_cnt)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCnt_get
- * Description:
- *      Get System auto learning limit number
- * Input:
- *      None
- * Output:
- *      pMac_cnt - Auto learning entries limit number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get system ASIC auto learning limit number.
- */
-rtk_api_ret_t rtk_l2_limitSystemLearningCnt_get(rtk_mac_cnt_t *pMac_cnt)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMac_cnt)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSystemLutLearnLimitNo(pMac_cnt)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitLearningCntAction_set
- * Description:
- *      Configure auto learn over limit number action.
- * Input:
- *      port - Port id.
- *      action - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_NOT_ALLOWED  - Invalid learn over action
- * Note:
- *      The API can set SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-rtk_api_ret_t rtk_l2_limitLearningCntAction_set(rtk_port_t port, rtk_l2_limitLearnCntAction_t action)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 data;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if ( LIMIT_LEARN_CNT_ACTION_DROP == action )
-        data = 1;
-    else if ( LIMIT_LEARN_CNT_ACTION_FORWARD == action )
-        data = 0;
-    else if ( LIMIT_LEARN_CNT_ACTION_TO_CPU == action )
-        data = 2;
-    else
-        return RT_ERR_NOT_ALLOWED;
-
-    if ((retVal = rtl8367c_setAsicLutLearnOverAct(data)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitLearningCntAction_get
- * Description:
- *      Get auto learn over limit number action.
- * Input:
- *      port - Port id.
- * Output:
- *      pAction - Learn over action
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-rtk_api_ret_t rtk_l2_limitLearningCntAction_get(rtk_port_t port, rtk_l2_limitLearnCntAction_t *pAction)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 action;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLutLearnOverAct(&action)) != RT_ERR_OK)
-        return retVal;
-
-    if ( 1 == action )
-        *pAction = LIMIT_LEARN_CNT_ACTION_DROP;
-    else if ( 0 == action )
-        *pAction = LIMIT_LEARN_CNT_ACTION_FORWARD;
-    else if ( 2 == action )
-        *pAction = LIMIT_LEARN_CNT_ACTION_TO_CPU;
-    else
-    *pAction = action;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntAction_set
- * Description:
- *      Configure system auto learn over limit number action.
- * Input:
- *      port - Port id.
- *      action - Auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_NOT_ALLOWED  - Invalid learn over action
- * Note:
- *      The API can set SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-rtk_api_ret_t rtk_l2_limitSystemLearningCntAction_set(rtk_l2_limitLearnCntAction_t action)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 data;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ( LIMIT_LEARN_CNT_ACTION_DROP == action )
-        data = 1;
-    else if ( LIMIT_LEARN_CNT_ACTION_FORWARD == action )
-        data = 0;
-    else if ( LIMIT_LEARN_CNT_ACTION_TO_CPU == action )
-        data = 2;
-    else
-        return RT_ERR_NOT_ALLOWED;
-
-    if ((retVal = rtl8367c_setAsicSystemLutLearnOverAct(data)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntAction_get
- * Description:
- *      Get system auto learn over limit number action.
- * Input:
- *      None.
- * Output:
- *      pAction - Learn over action
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get SA unknown packet action while auto learn limit number is over
- *      The action symbol as following:
- *      - LIMIT_LEARN_CNT_ACTION_DROP,
- *      - LIMIT_LEARN_CNT_ACTION_FORWARD,
- *      - LIMIT_LEARN_CNT_ACTION_TO_CPU,
- */
-rtk_api_ret_t rtk_l2_limitSystemLearningCntAction_get(rtk_l2_limitLearnCntAction_t *pAction)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 action;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSystemLutLearnOverAct(&action)) != RT_ERR_OK)
-        return retVal;
-
-    if ( 1 == action )
-        *pAction = LIMIT_LEARN_CNT_ACTION_DROP;
-    else if ( 0 == action )
-        *pAction = LIMIT_LEARN_CNT_ACTION_FORWARD;
-    else if ( 2 == action )
-        *pAction = LIMIT_LEARN_CNT_ACTION_TO_CPU;
-    else
-    *pAction = action;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntPortMask_set
- * Description:
- *      Configure system auto learn portmask
- * Input:
- *      pPortmask - Port Mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid port mask.
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_limitSystemLearningCntPortMask_set(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port mask */
-    RTK_CHK_PORTMASK_VALID(pPortmask);
-
-    if ((retVal = rtk_switch_portmask_L2P_get(pPortmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicSystemLutLearnPortMask(pmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_limitSystemLearningCntPortMask_get
- * Description:
- *      get system auto learn portmask
- * Input:
- *      None
- * Output:
- *      pPortmask - Port Mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Null pointer.
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_limitSystemLearningCntPortMask_get(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSystemLutLearnPortMask(&pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_learningCnt_get
- * Description:
- *      Get per-Port current auto learning number
- * Input:
- *      port - Port id.
- * Output:
- *      pMac_cnt - ASIC auto learning entries number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get per-port ASIC auto learning number
- */
-rtk_api_ret_t rtk_l2_learningCnt_get(rtk_port_t port, rtk_mac_cnt_t *pMac_cnt)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pMac_cnt)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLutLearnNo(rtk_switch_port_L2P_get(port), pMac_cnt)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_floodPortMask_set
- * Description:
- *      Set flooding portmask
- * Input:
- *      type - flooding type.
- *      pFlood_portmask - flooding porkmask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set the flooding mask.
- *      The flooding type is as following:
- *      - FLOOD_UNKNOWNDA
- *      - FLOOD_UNKNOWNMC
- *      - FLOOD_BC
- */
-rtk_api_ret_t rtk_l2_floodPortMask_set(rtk_l2_flood_type_t floood_type, rtk_portmask_t *pFlood_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (floood_type >= FLOOD_END)
-        return RT_ERR_INPUT;
-
-    /* check port valid */
-    RTK_CHK_PORTMASK_VALID(pFlood_portmask);
-
-    /* Get Physical port mask */
-    if ((retVal = rtk_switch_portmask_L2P_get(pFlood_portmask, &pmask))!=RT_ERR_OK)
-        return retVal;
-
-    switch (floood_type)
-    {
-        case FLOOD_UNKNOWNDA:
-            if ((retVal = rtl8367c_setAsicPortUnknownDaFloodingPortmask(pmask)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case FLOOD_UNKNOWNMC:
-            if ((retVal = rtl8367c_setAsicPortUnknownMulticastFloodingPortmask(pmask)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case FLOOD_BC:
-            if ((retVal = rtl8367c_setAsicPortBcastFloodingPortmask(pmask)) != RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtk_l2_floodPortMask_get
- * Description:
- *      Get flooding portmask
- * Input:
- *      type - flooding type.
- * Output:
- *      pFlood_portmask - flooding porkmask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get the flooding mask.
- *      The flooding type is as following:
- *      - FLOOD_UNKNOWNDA
- *      - FLOOD_UNKNOWNMC
- *      - FLOOD_BC
- */
-rtk_api_ret_t rtk_l2_floodPortMask_get(rtk_l2_flood_type_t floood_type, rtk_portmask_t *pFlood_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (floood_type >= FLOOD_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pFlood_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    switch (floood_type)
-    {
-        case FLOOD_UNKNOWNDA:
-            if ((retVal = rtl8367c_getAsicPortUnknownDaFloodingPortmask(&pmask)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case FLOOD_UNKNOWNMC:
-            if ((retVal = rtl8367c_getAsicPortUnknownMulticastFloodingPortmask(&pmask)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case FLOOD_BC:
-            if ((retVal = rtl8367c_getAsicPortBcastFloodingPortmask(&pmask)) != RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    /* Get Logical port mask */
-    if ((retVal = rtk_switch_portmask_P2L_get(pmask, pFlood_portmask))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_localPktPermit_set
- * Description:
- *      Set permittion of frames if source port and destination port are the same.
- * Input:
- *      port - Port id.
- *      permit - permittion status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid permit value.
- * Note:
- *      This API is setted to permit frame if its source port is equal to destination port.
- */
-rtk_api_ret_t rtk_l2_localPktPermit_set(rtk_port_t port, rtk_enable_t permit)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (permit >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortBlockSpa(rtk_switch_port_L2P_get(port), permit)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_localPktPermit_get
- * Description:
- *      Get permittion of frames if source port and destination port are the same.
- * Input:
- *      port - Port id.
- * Output:
- *      pPermit - permittion status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API is to get permittion status for frames if its source port is equal to destination port.
- */
-rtk_api_ret_t rtk_l2_localPktPermit_get(rtk_port_t port, rtk_enable_t *pPermit)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pPermit)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortBlockSpa(rtk_switch_port_L2P_get(port), pPermit)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_aging_set
- * Description:
- *      Set LUT agging out speed
- * Input:
- *      aging_time - Agging out time.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can set LUT agging out period for each entry and the range is from 45s to 458s.
- */
-rtk_api_ret_t rtk_l2_aging_set(rtk_l2_age_time_t aging_time)
-{
-    rtk_uint32 i;
-    CONST_T rtk_uint32 agePara[10][3] = {
-        {45, 0, 1}, {88, 0, 2}, {133, 0, 3}, {177, 0, 4}, {221, 0, 5}, {266, 0, 6}, {310, 0, 7},
-        {354, 2, 6}, {413, 2, 7}, {458, 3, 7}};
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (aging_time>agePara[9][0])
-        return RT_ERR_OUT_OF_RANGE;
-
-    for (i = 0; i<10; i++)
-    {
-        if (aging_time<=agePara[i][0])
-        {
-            return rtl8367c_setAsicLutAgeTimerSpeed(agePara[i][2], agePara[i][1]);
-        }
-    }
-
-    return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_l2_aging_get
- * Description:
- *      Get LUT agging out time
- * Input:
- *      None
- * Output:
- *      pEnable - Aging status
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get LUT agging out period for each entry.
- */
-rtk_api_ret_t rtk_l2_aging_get(rtk_l2_age_time_t *pAging_time)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i,time, speed;
-    CONST_T rtk_uint32 agePara[10][3] = {
-        {45, 0, 1}, {88, 0, 2}, {133, 0, 3}, {177, 0, 4}, {221, 0, 5}, {266, 0, 6}, {310, 0, 7},
-        {354, 2, 6}, {413, 2, 7}, {458, 3, 7}};
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAging_time)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLutAgeTimerSpeed(&time, &speed)) != RT_ERR_OK)
-        return retVal;
-
-    for (i = 0; i<10; i++)
-    {
-        if (time==agePara[i][2]&&speed==agePara[i][1])
-        {
-            *pAging_time = agePara[i][0];
-            return RT_ERR_OK;
-        }
-    }
-
-    return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastAddrLookup_set
- * Description:
- *      Set Lut IP multicast lookup function
- * Input:
- *      type - Lookup type for IPMC packet.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      LOOKUP_MAC      - Lookup by MAC address
- *      LOOKUP_IP       - Lookup by IP address
- *      LOOKUP_IP_VID   - Lookup by IP address & VLAN ID
- */
-rtk_api_ret_t rtk_l2_ipMcastAddrLookup_set(rtk_l2_ipmc_lookup_type_t type)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(type == LOOKUP_MAC)
-    {
-        if((retVal = rtl8367c_setAsicLutIpMulticastLookup(DISABLED)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if(type == LOOKUP_IP)
-    {
-        if((retVal = rtl8367c_setAsicLutIpMulticastLookup(ENABLED)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutIpMulticastVidLookup(DISABLED))!=RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutIpLookupMethod(1))!=RT_ERR_OK)
-            return retVal;
-    }
-    else if(type == LOOKUP_IP_VID)
-    {
-        if((retVal = rtl8367c_setAsicLutIpMulticastLookup(ENABLED)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutIpMulticastVidLookup(ENABLED))!=RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicLutIpLookupMethod(1))!=RT_ERR_OK)
-            return retVal;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastAddrLookup_get
- * Description:
- *      Get Lut IP multicast lookup function
- * Input:
- *      None.
- * Output:
- *      pType - Lookup type for IPMC packet.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_l2_ipMcastAddrLookup_get(rtk_l2_ipmc_lookup_type_t *pType)
-{
-    rtk_api_ret_t       retVal;
-    rtk_uint32          enabled, vid_lookup;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pType)
-        return RT_ERR_NULL_POINTER;
-
-    if((retVal = rtl8367c_getAsicLutIpMulticastLookup(&enabled)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicLutIpMulticastVidLookup(&vid_lookup))!=RT_ERR_OK)
-        return retVal;
-
-    if(enabled == ENABLED)
-    {
-        if(vid_lookup == ENABLED)
-            *pType = LOOKUP_IP_VID;
-        else
-            *pType = LOOKUP_IP;
-    }
-    else
-        *pType = LOOKUP_MAC;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastForwardRouterPort_set
- * Description:
- *      Set IPMC packet forward to rounter port also or not
- * Input:
- *      enabled - 1: Inlcude router port, 0, exclude router port
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_ipMcastForwardRouterPort_set(rtk_enable_t enabled)
-{
-    rtk_api_ret_t       retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enabled >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if((retVal = rtl8367c_setAsicLutIpmcFwdRouterPort(enabled)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastForwardRouterPort_get
- * Description:
- *      Get IPMC packet forward to rounter port also or not
- * Input:
- *      None.
- * Output:
- *      pEnabled    - 1: Inlcude router port, 0, exclude router port
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_l2_ipMcastForwardRouterPort_get(rtk_enable_t *pEnabled)
-{
-    rtk_api_ret_t       retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    if((retVal = rtl8367c_getAsicLutIpmcFwdRouterPort(pEnabled)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastGroupEntry_add
- * Description:
- *      Add an IP Multicast entry to group table
- * Input:
- *      ip_addr     - IP address
- *      vid         - VLAN ID
- *      pPortmask   - portmask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- *      RT_ERR_TBL_FULL    - Table Full
- * Note:
- *      Add an entry to IP Multicast Group table.
- */
-rtk_api_ret_t rtk_l2_ipMcastGroupEntry_add(ipaddr_t ip_addr, rtk_uint32 vid, rtk_portmask_t *pPortmask)
-{
-    rtk_uint32      empty_idx = 0xFFFF;
-    rtk_int32       index;
-    ipaddr_t        group_addr;
-    rtk_uint32      group_vid;
-    rtk_uint32      pmask;
-    rtk_uint32      valid;
-    rtk_uint32      physicalPortmask;
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_L2_VID;
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if((ip_addr & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    /* Get Physical port mask */
-    if ((retVal = rtk_switch_portmask_L2P_get(pPortmask, &physicalPortmask))!=RT_ERR_OK)
-        return retVal;
-
-    for(index = 0; index <= RTL8367C_LUT_IPMCGRP_TABLE_MAX; index++)
-    {
-        if ((retVal = rtl8367c_getAsicLutIPMCGroup((rtk_uint32)index, &group_addr, &group_vid, &pmask, &valid))!=RT_ERR_OK)
-            return retVal;
-
-        if( (valid == ENABLED) && (group_addr == ip_addr) && (group_vid == vid) )
-        {
-            if(pmask != physicalPortmask)
-            {
-                pmask = physicalPortmask;
-                if ((retVal = rtl8367c_setAsicLutIPMCGroup(index, ip_addr, vid, pmask, valid))!=RT_ERR_OK)
-                    return retVal;
-            }
-
-            return RT_ERR_OK;
-        }
-
-        if( (valid == DISABLED) && (empty_idx == 0xFFFF) ) /* Unused */
-            empty_idx = (rtk_uint32)index;
-    }
-
-    if(empty_idx == 0xFFFF)
-        return RT_ERR_TBL_FULL;
-
-    pmask = physicalPortmask;
-    if ((retVal = rtl8367c_setAsicLutIPMCGroup(empty_idx, ip_addr, vid, pmask, ENABLED))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastGroupEntry_del
- * Description:
- *      Delete an entry from IP Multicast group table
- * Input:
- *      ip_addr     - IP address
- *      vid         - VLAN ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- *      RT_ERR_TBL_FULL    - Table Full
- * Note:
- *      Delete an entry from IP Multicast group table.
- */
-rtk_api_ret_t rtk_l2_ipMcastGroupEntry_del(ipaddr_t ip_addr, rtk_uint32 vid)
-{
-    rtk_int32       index;
-    ipaddr_t        group_addr;
-    rtk_uint32      group_vid;
-    rtk_uint32      pmask;
-    rtk_uint32      valid;
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_L2_VID;
-
-    if((ip_addr & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    for(index = 0; index <= RTL8367C_LUT_IPMCGRP_TABLE_MAX; index++)
-    {
-        if ((retVal = rtl8367c_getAsicLutIPMCGroup((rtk_uint32)index, &group_addr, &group_vid, &pmask, &valid))!=RT_ERR_OK)
-            return retVal;
-
-        if( (valid == ENABLED) && (group_addr == ip_addr) && (group_vid == vid) )
-        {
-            group_addr = 0xE0000000;
-            group_vid = 0;
-            pmask = 0;
-            if ((retVal = rtl8367c_setAsicLutIPMCGroup(index, group_addr, group_vid, pmask, DISABLED))!=RT_ERR_OK)
-                return retVal;
-
-            return RT_ERR_OK;
-        }
-    }
-
-    return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_l2_ipMcastGroupEntry_get
- * Description:
- *      get an entry from IP Multicast group table
- * Input:
- *      ip_addr     - IP address
- *      vid         - VLAN ID
- * Output:
- *      pPortmask   - member port mask
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- *      RT_ERR_TBL_FULL    - Table Full
- * Note:
- *      Delete an entry from IP Multicast group table.
- */
-rtk_api_ret_t rtk_l2_ipMcastGroupEntry_get(ipaddr_t ip_addr, rtk_uint32 vid, rtk_portmask_t *pPortmask)
-{
-    rtk_int32       index;
-    ipaddr_t        group_addr;
-    rtk_uint32      group_vid;
-    rtk_uint32      valid;
-    rtk_uint32      pmask;
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if((ip_addr & 0xF0000000) != 0xE0000000)
-        return RT_ERR_INPUT;
-
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_L2_VID;
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    for(index = 0; index <= RTL8367C_LUT_IPMCGRP_TABLE_MAX; index++)
-    {
-        if ((retVal = rtl8367c_getAsicLutIPMCGroup((rtk_uint32)index, &group_addr, &group_vid, &pmask, &valid))!=RT_ERR_OK)
-            return retVal;
-
-        if( (valid == ENABLED) && (group_addr == ip_addr) && (group_vid == vid) )
-        {
-            if ((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask))!=RT_ERR_OK)
-                return retVal;
-
-            return RT_ERR_OK;
-        }
-    }
-
-    return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_l2_entry_get
- * Description:
- *      Get LUT unicast entry.
- * Input:
- *      pL2_entry - Index field in the structure.
- * Output:
- *      pL2_entry - other fields such as MAC, port, age...
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_L2_EMPTY_ENTRY   - Empty LUT entry.
- *      RT_ERR_INPUT            - Invalid input parameters.
- * Note:
- *      This API is used to get address by index from 0~2111.
- */
-rtk_api_ret_t rtk_l2_entry_get(rtk_l2_addr_table_t *pL2_entry)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 method;
-    rtl8367c_luttb l2Table;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (pL2_entry->index >= rtk_switch_maxLutAddrNumber_get())
-        return RT_ERR_INPUT;
-
-    memset(&l2Table, 0x00, sizeof(rtl8367c_luttb));
-    l2Table.address= pL2_entry->index;
-    method = LUTREADMETHOD_ADDRESS;
-    if ((retVal = rtl8367c_getAsicL2LookupTb(method, &l2Table)) != RT_ERR_OK)
-        return retVal;
-
-    if ((pL2_entry->index>0x800)&&(l2Table.lookup_hit==0))
-         return RT_ERR_L2_EMPTY_ENTRY;
-
-    if(l2Table.l3lookup)
-    {
-        if(l2Table.l3vidlookup)
-        {
-            memset(&pL2_entry->mac, 0, sizeof(rtk_mac_t));
-            pL2_entry->is_ipmul  = l2Table.l3lookup;
-            pL2_entry->sip       = l2Table.sip;
-            pL2_entry->dip       = l2Table.dip;
-            pL2_entry->is_static = l2Table.nosalearn;
-
-            /* Get Logical port mask */
-            if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &(pL2_entry->portmask)))!=RT_ERR_OK)
-                return retVal;
-
-            pL2_entry->fid       = 0;
-            pL2_entry->age       = 0;
-            pL2_entry->auth      = 0;
-            pL2_entry->sa_block  = 0;
-            pL2_entry->is_ipvidmul = 1;
-            pL2_entry->l3_vid      = l2Table.l3_vid;
-        }
-        else
-        {
-            memset(&pL2_entry->mac, 0, sizeof(rtk_mac_t));
-            pL2_entry->is_ipmul  = l2Table.l3lookup;
-            pL2_entry->sip       = l2Table.sip;
-            pL2_entry->dip       = l2Table.dip;
-            pL2_entry->is_static = l2Table.nosalearn;
-
-            /* Get Logical port mask */
-            if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &(pL2_entry->portmask)))!=RT_ERR_OK)
-                return retVal;
-
-            pL2_entry->fid       = 0;
-            pL2_entry->age       = 0;
-            pL2_entry->auth      = 0;
-            pL2_entry->sa_block  = 0;
-            pL2_entry->is_ipvidmul = 0;
-            pL2_entry->l3_vid      = 0;
-        }
-    }
-    else if(l2Table.mac.octet[0]&0x01)
-    {
-        memset(&pL2_entry->sip, 0, sizeof(ipaddr_t));
-        memset(&pL2_entry->dip, 0, sizeof(ipaddr_t));
-        pL2_entry->mac.octet[0] = l2Table.mac.octet[0];
-        pL2_entry->mac.octet[1] = l2Table.mac.octet[1];
-        pL2_entry->mac.octet[2] = l2Table.mac.octet[2];
-        pL2_entry->mac.octet[3] = l2Table.mac.octet[3];
-        pL2_entry->mac.octet[4] = l2Table.mac.octet[4];
-        pL2_entry->mac.octet[5] = l2Table.mac.octet[5];
-        pL2_entry->is_ipmul  = l2Table.l3lookup;
-        pL2_entry->is_static = l2Table.nosalearn;
-
-        /* Get Logical port mask */
-        if ((retVal = rtk_switch_portmask_P2L_get(l2Table.mbr, &(pL2_entry->portmask)))!=RT_ERR_OK)
-            return retVal;
-
-        pL2_entry->ivl       = l2Table.ivl_svl;
-        if(l2Table.ivl_svl == 1) /* IVL */
-        {
-            pL2_entry->cvid      = l2Table.cvid_fid;
-            pL2_entry->fid       = 0;
-        }
-        else /* SVL*/
-        {
-            pL2_entry->cvid      = 0;
-            pL2_entry->fid       = l2Table.cvid_fid;
-        }
-        pL2_entry->auth      = l2Table.auth;
-        pL2_entry->sa_block  = l2Table.sa_block;
-        pL2_entry->age       = 0;
-        pL2_entry->is_ipvidmul = 0;
-        pL2_entry->l3_vid      = 0;
-    }
-    else if((l2Table.age != 0)||(l2Table.nosalearn == 1))
-    {
-        memset(&pL2_entry->sip, 0, sizeof(ipaddr_t));
-        memset(&pL2_entry->dip, 0, sizeof(ipaddr_t));
-        pL2_entry->mac.octet[0] = l2Table.mac.octet[0];
-        pL2_entry->mac.octet[1] = l2Table.mac.octet[1];
-        pL2_entry->mac.octet[2] = l2Table.mac.octet[2];
-        pL2_entry->mac.octet[3] = l2Table.mac.octet[3];
-        pL2_entry->mac.octet[4] = l2Table.mac.octet[4];
-        pL2_entry->mac.octet[5] = l2Table.mac.octet[5];
-        pL2_entry->is_ipmul  = l2Table.l3lookup;
-        pL2_entry->is_static = l2Table.nosalearn;
-
-        /* Get Logical port mask */
-        if ((retVal = rtk_switch_portmask_P2L_get(1<<(l2Table.spa), &(pL2_entry->portmask)))!=RT_ERR_OK)
-            return retVal;
-
-        pL2_entry->ivl       = l2Table.ivl_svl;
-        pL2_entry->cvid      = l2Table.cvid_fid;
-        pL2_entry->fid       = l2Table.fid;
-        pL2_entry->auth      = l2Table.auth;
-        pL2_entry->sa_block  = l2Table.sa_block;
-        pL2_entry->age       = l2Table.age;
-        pL2_entry->is_ipvidmul = 0;
-        pL2_entry->l3_vid      = 0;
-    }
-    else
-       return RT_ERR_L2_EMPTY_ENTRY;
-
-    return RT_ERR_OK;
-}
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/leaky.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/leaky.c
deleted file mode 100644
index 1b7d50a9e5..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/leaky.c
+++ /dev/null
@@ -1,590 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in Leaky module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <leaky.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_portIsolation.h>
-#include <rtl8367c_asicdrv_rma.h>
-#include <rtl8367c_asicdrv_igmp.h>
-
-
-/* Function Name:
- *      rtk_leaky_vlan_set
- * Description:
- *      Set VLAN leaky.
- * Input:
- *      type - Packet type for VLAN leaky.
- *      enable - Leaky status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      This API can set VLAN leaky for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-rtk_api_ret_t rtk_leaky_vlan_set(rtk_leaky_type_t type, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= LEAKY_END)
-        return RT_ERR_INPUT;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (type >= 0 && type <= LEAKY_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.vlan_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_IPMULTICAST == type)
-    {
-        for (port = 0; port <= RTK_PORT_ID_MAX; port++)
-        {
-            if ((retVal = rtl8367c_setAsicIpMulticastVlanLeaky(port,enable)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-    else if (LEAKY_IGMP == type)
-    {
-        if ((retVal = rtl8367c_setAsicIGMPVLANLeaky(enable)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_CDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.vlan_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_CSSTP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.vlan_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_LLDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp,&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.vlan_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaLldp(tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_leaky_vlan_get
- * Description:
- *      Get VLAN leaky.
- * Input:
- *      type - Packet type for VLAN leaky.
- * Output:
- *      pEnable - Leaky status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get VLAN leaky status for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP  packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-rtk_api_ret_t rtk_leaky_vlan_get(rtk_leaky_type_t type, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port,tmp;
-    rtl8367c_rma_t rmacfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= LEAKY_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if (type >= 0 && type <= LEAKY_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.vlan_leaky;
-
-    }
-    else if (LEAKY_IPMULTICAST == type)
-    {
-        for (port = 0; port <= RTK_PORT_ID_MAX; port++)
-        {
-            if ((retVal = rtl8367c_getAsicIpMulticastVlanLeaky(port, &tmp)) != RT_ERR_OK)
-                return retVal;
-            if (port>0&&(tmp!=*pEnable))
-                return RT_ERR_FAILED;
-            *pEnable = tmp;
-        }
-    }
-    else if (LEAKY_IGMP == type)
-    {
-        if ((retVal = rtl8367c_getAsicIGMPVLANLeaky(&tmp)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = tmp;
-    }
-    else if (LEAKY_CDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.vlan_leaky;
-    }
-    else if (LEAKY_CSSTP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.vlan_leaky;
-    }
-    else if (LEAKY_LLDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.vlan_leaky;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_leaky_portIsolation_set
- * Description:
- *      Set port isolation leaky.
- * Input:
- *      type - Packet type for port isolation leaky.
- *      enable - Leaky status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      This API can set port isolation leaky for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP  packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-rtk_api_ret_t rtk_leaky_portIsolation_set(rtk_leaky_type_t type, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= LEAKY_END)
-        return RT_ERR_INPUT;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (type >= 0 && type <= LEAKY_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.portiso_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_IPMULTICAST == type)
-    {
-        for (port = 0; port < RTK_MAX_NUM_OF_PORT; port++)
-        {
-            if ((retVal = rtl8367c_setAsicIpMulticastPortIsoLeaky(port,enable)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-    else if (LEAKY_IGMP == type)
-    {
-        if ((retVal = rtl8367c_setAsicIGMPIsoLeaky(enable)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_CDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.portiso_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_CSSTP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.portiso_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (LEAKY_LLDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.portiso_leaky = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaLldp(tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_leaky_portIsolation_get
- * Description:
- *      Get port isolation leaky.
- * Input:
- *      type - Packet type for port isolation leaky.
- * Output:
- *      pEnable - Leaky status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get port isolation leaky status for RMA ,IGMP/MLD, CDP, CSSTP, and LLDP  packets.
- *      The leaky frame types are as following:
- *      - LEAKY_BRG_GROUP,
- *      - LEAKY_FD_PAUSE,
- *      - LEAKY_SP_MCAST,
- *      - LEAKY_1X_PAE,
- *      - LEAKY_UNDEF_BRG_04,
- *      - LEAKY_UNDEF_BRG_05,
- *      - LEAKY_UNDEF_BRG_06,
- *      - LEAKY_UNDEF_BRG_07,
- *      - LEAKY_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - LEAKY_UNDEF_BRG_09,
- *      - LEAKY_UNDEF_BRG_0A,
- *      - LEAKY_UNDEF_BRG_0B,
- *      - LEAKY_UNDEF_BRG_0C,
- *      - LEAKY_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - LEAKY_8021AB,
- *      - LEAKY_UNDEF_BRG_0F,
- *      - LEAKY_BRG_MNGEMENT,
- *      - LEAKY_UNDEFINED_11,
- *      - LEAKY_UNDEFINED_12,
- *      - LEAKY_UNDEFINED_13,
- *      - LEAKY_UNDEFINED_14,
- *      - LEAKY_UNDEFINED_15,
- *      - LEAKY_UNDEFINED_16,
- *      - LEAKY_UNDEFINED_17,
- *      - LEAKY_UNDEFINED_18,
- *      - LEAKY_UNDEFINED_19,
- *      - LEAKY_UNDEFINED_1A,
- *      - LEAKY_UNDEFINED_1B,
- *      - LEAKY_UNDEFINED_1C,
- *      - LEAKY_UNDEFINED_1D,
- *      - LEAKY_UNDEFINED_1E,
- *      - LEAKY_UNDEFINED_1F,
- *      - LEAKY_GMRP,
- *      - LEAKY_GVRP,
- *      - LEAKY_UNDEF_GARP_22,
- *      - LEAKY_UNDEF_GARP_23,
- *      - LEAKY_UNDEF_GARP_24,
- *      - LEAKY_UNDEF_GARP_25,
- *      - LEAKY_UNDEF_GARP_26,
- *      - LEAKY_UNDEF_GARP_27,
- *      - LEAKY_UNDEF_GARP_28,
- *      - LEAKY_UNDEF_GARP_29,
- *      - LEAKY_UNDEF_GARP_2A,
- *      - LEAKY_UNDEF_GARP_2B,
- *      - LEAKY_UNDEF_GARP_2C,
- *      - LEAKY_UNDEF_GARP_2D,
- *      - LEAKY_UNDEF_GARP_2E,
- *      - LEAKY_UNDEF_GARP_2F,
- *      - LEAKY_IGMP,
- *      - LEAKY_IPMULTICAST.
- *      - LEAKY_CDP,
- *      - LEAKY_CSSTP,
- *      - LEAKY_LLDP.
- */
-rtk_api_ret_t rtk_leaky_portIsolation_get(rtk_leaky_type_t type, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port, tmp;
-    rtl8367c_rma_t rmacfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= LEAKY_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if (type >= 0 && type <= LEAKY_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.portiso_leaky;
-
-    }
-    else if (LEAKY_IPMULTICAST == type)
-    {
-        for (port = 0; port < RTK_MAX_NUM_OF_PORT; port++)
-        {
-            if ((retVal = rtl8367c_getAsicIpMulticastPortIsoLeaky(port, &tmp)) != RT_ERR_OK)
-                return retVal;
-            if (port > 0 &&(tmp != *pEnable))
-                return RT_ERR_FAILED;
-            *pEnable = tmp;
-        }
-    }
-    else if (LEAKY_IGMP == type)
-    {
-        if ((retVal = rtl8367c_getAsicIGMPIsoLeaky(&tmp)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = tmp;
-    }
-    else if (LEAKY_CDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.portiso_leaky;
-    }
-    else if (LEAKY_CSSTP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.portiso_leaky;
-    }
-    else if (LEAKY_LLDP == type)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.portiso_leaky;
-    }
-
-
-    return RT_ERR_OK;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/led.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/led.c
deleted file mode 100644
index c00c331d8a..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/led.c
+++ /dev/null
@@ -1,792 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in LED module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <led.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_led.h>
-
-
-/* Function Name:
- *      rtk_led_enable_set
- * Description:
- *      Set Led enable congiuration
- * Input:
- *      group       - LED group id.
- *      pPortmask   - LED enable port mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_MASK    - Error portmask
- * Note:
- *      The API can be used to enable LED per port per group.
- */
-rtk_api_ret_t rtk_led_enable_set(rtk_led_group_t group, rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-    rtk_port_t port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (group >= LED_GROUP_END)
-        return RT_ERR_INPUT;
-
-    RTK_CHK_PORTMASK_VALID(pPortmask);
-
-    RTK_PORTMASK_SCAN((*pPortmask), port)
-    {
-        if(rtk_switch_isCPUPort(port) == RT_ERR_OK)
-            return RT_ERR_PORT_MASK;
-    }
-
-    if((retVal = rtk_switch_portmask_L2P_get(pPortmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicLedGroupEnable(group, pmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_enable_get
- * Description:
- *      Get Led enable congiuration
- * Input:
- *      group - LED group id.
- * Output:
- *      pPortmask - LED enable port mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can be used to get LED enable status.
- */
-rtk_api_ret_t rtk_led_enable_get(rtk_led_group_t group, rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (group >= LED_GROUP_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_getAsicLedGroupEnable(group, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_led_operation_set
- * Description:
- *      Set Led operation mode
- * Input:
- *      mode - LED operation mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set Led operation mode.
- *      The modes that can be set are as following:
- *      - LED_OP_SCAN,
- *      - LED_OP_PARALLEL,
- *      - LED_OP_SERIAL,
- */
-rtk_api_ret_t rtk_led_operation_set(rtk_led_operation_t mode)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ( mode >= LED_OP_END)
-      return RT_ERR_INPUT;
-
-    switch (mode)
-    {
-        case LED_OP_PARALLEL:
-            regData = LEDOP_PARALLEL;
-            break;
-        case LED_OP_SERIAL:
-            regData = LEDOP_SERIAL;
-            break;
-        default:
-            return RT_ERR_CHIP_NOT_SUPPORTED;
-            break;
-    }
-
-    if ((retVal = rtl8367c_setAsicLedOperationMode(regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_operation_get
- * Description:
- *      Get Led operation mode
- * Input:
- *      None
- * Output:
- *      pMode - Support LED operation mode.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get Led operation mode.
- *      The modes that can be set are as following:
- *      - LED_OP_SCAN,
- *      - LED_OP_PARALLEL,
- *      - LED_OP_SERIAL,
- */
-rtk_api_ret_t rtk_led_operation_get(rtk_led_operation_t *pMode)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMode)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLedOperationMode(&regData)) != RT_ERR_OK)
-        return retVal;
-
-    if (regData == LEDOP_SERIAL)
-        *pMode = LED_OP_SERIAL;
-    else if (regData ==LEDOP_PARALLEL)
-        *pMode = LED_OP_PARALLEL;
-    else
-       return RT_ERR_FAILED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_modeForce_set
- * Description:
- *      Set Led group to congiuration force mode
- * Input:
- *      port    - port ID
- *      group   - Support LED group id.
- *      mode    - Support LED force mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Error Port ID
- * Note:
- *      The API can force to one force mode.
- *      The force modes that can be set are as following:
- *      - LED_FORCE_NORMAL,
- *      - LED_FORCE_BLINK,
- *      - LED_FORCE_OFF,
- *      - LED_FORCE_ON.
- */
-rtk_api_ret_t rtk_led_modeForce_set(rtk_port_t port, rtk_led_group_t group, rtk_led_force_mode_t mode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    /* No LED for CPU port */
-    if(rtk_switch_isCPUPort(port) == RT_ERR_OK)
-        return RT_ERR_PORT_ID;
-
-    if (group >= LED_GROUP_END)
-        return RT_ERR_INPUT;
-
-    if (mode >= LED_FORCE_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    if ((retVal = rtl8367c_setAsicForceLed(rtk_switch_port_L2P_get(port), group, mode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_modeForce_get
- * Description:
- *      Get Led group to congiuration force mode
- * Input:
- *      port  - port ID
- *      group - Support LED group id.
- *      pMode - Support LED force mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Error Port ID
- * Note:
- *      The API can get forced Led group mode.
- *      The force modes that can be set are as following:
- *      - LED_FORCE_NORMAL,
- *      - LED_FORCE_BLINK,
- *      - LED_FORCE_OFF,
- *      - LED_FORCE_ON.
- */
-rtk_api_ret_t rtk_led_modeForce_get(rtk_port_t port, rtk_led_group_t group, rtk_led_force_mode_t *pMode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    /* No LED for CPU port */
-    if(rtk_switch_isCPUPort(port) == RT_ERR_OK)
-        return RT_ERR_PORT_ID;
-
-    if (group >= LED_GROUP_END)
-        return RT_ERR_INPUT;
-
-    if (NULL == pMode)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicForceLed(rtk_switch_port_L2P_get(port), group, pMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_blinkRate_set
- * Description:
- *      Set LED blinking rate
- * Input:
- *      blinkRate - blinking rate.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      ASIC support 6 types of LED blinking rates at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms.
- */
-rtk_api_ret_t rtk_led_blinkRate_set(rtk_led_blink_rate_t blinkRate)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (blinkRate >= LED_BLINKRATE_END)
-        return RT_ERR_FAILED;
-
-    if ((retVal = rtl8367c_setAsicLedBlinkRate(blinkRate)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_blinkRate_get
- * Description:
- *      Get LED blinking rate at mode 0 to mode 3
- * Input:
- *      None
- * Output:
- *      pBlinkRate - blinking rate.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      There are  6 types of LED blinking rates at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms.
- */
-rtk_api_ret_t rtk_led_blinkRate_get(rtk_led_blink_rate_t *pBlinkRate)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pBlinkRate)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLedBlinkRate(pBlinkRate)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_groupConfig_set
- * Description:
- *      Set per group Led to congiuration mode
- * Input:
- *      group   - LED group.
- *      config  - LED configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set LED indicated information configuration for each LED group with 1 to 1 led mapping to each port.
- *      - Definition  LED Statuses      Description
- *      - 0000        LED_Off           LED pin Tri-State.
- *      - 0001        Dup/Col           Collision, Full duplex Indicator.
- *      - 0010        Link/Act          Link, Activity Indicator.
- *      - 0011        Spd1000           1000Mb/s Speed Indicator.
- *      - 0100        Spd100            100Mb/s Speed Indicator.
- *      - 0101        Spd10             10Mb/s Speed Indicator.
- *      - 0110        Spd1000/Act       1000Mb/s Speed/Activity Indicator.
- *      - 0111        Spd100/Act        100Mb/s Speed/Activity Indicator.
- *      - 1000        Spd10/Act         10Mb/s Speed/Activity Indicator.
- *      - 1001        Spd100 (10)/Act   10/100Mb/s Speed/Activity Indicator.
- *      - 1010        LoopDetect        LoopDetect Indicator.
- *      - 1011        EEE               EEE Indicator.
- *      - 1100        Link/Rx           Link, Activity Indicator.
- *      - 1101        Link/Tx           Link, Activity Indicator.
- *      - 1110        Master            Link on Master Indicator.
- *      - 1111        Act               Activity Indicator. Low for link established.
- */
-rtk_api_ret_t rtk_led_groupConfig_set(rtk_led_group_t group, rtk_led_congig_t config)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (LED_GROUP_END <= group)
-        return RT_ERR_FAILED;
-
-    if (LED_CONFIG_END <= config)
-        return RT_ERR_FAILED;
-
-    if ((retVal = rtl8367c_setAsicLedIndicateInfoConfig(group, config)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_groupConfig_get
- * Description:
- *      Get Led group congiuration mode
- * Input:
- *      group - LED group.
- * Output:
- *      pConfig - LED configuration.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *       The API can get LED indicated information configuration for each LED group.
- */
-rtk_api_ret_t rtk_led_groupConfig_get(rtk_led_group_t group, rtk_led_congig_t *pConfig)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (LED_GROUP_END <= group)
-        return RT_ERR_FAILED;
-
-    if(NULL == pConfig)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLedIndicateInfoConfig(group, pConfig)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_groupAbility_set
- * Description:
- *      Configure per group Led ability
- * Input:
- *      group    - LED group.
- *      pAbility - LED ability
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      None.
- */
-
-rtk_api_ret_t rtk_led_groupAbility_set(rtk_led_group_t group, rtk_led_ability_t *pAbility)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (LED_GROUP_END <= group)
-        return RT_ERR_FAILED;
-
-    if(pAbility == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if( (pAbility->link_10m >= RTK_ENABLE_END) || (pAbility->link_100m >= RTK_ENABLE_END)||
-        (pAbility->link_500m >= RTK_ENABLE_END) || (pAbility->link_1000m >= RTK_ENABLE_END)||
-        (pAbility->act_rx >= RTK_ENABLE_END) || (pAbility->act_tx >= RTK_ENABLE_END) )
-    {
-        return RT_ERR_INPUT;
-    }
-
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_LED0_DATA_CTRL + (rtk_uint32)group, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(pAbility->link_10m == ENABLED)
-        regData |= 0x0001;
-    else
-        regData &= ~0x0001;
-
-    if(pAbility->link_100m == ENABLED)
-        regData |= 0x0002;
-    else
-        regData &= ~0x0002;
-
-    if(pAbility->link_500m == ENABLED)
-        regData |= 0x0004;
-    else
-        regData &= ~0x0004;
-
-    if(pAbility->link_1000m == ENABLED)
-        regData |= 0x0008;
-    else
-        regData &= ~0x0008;
-
-    if(pAbility->act_rx == ENABLED)
-        regData |= 0x0010;
-    else
-        regData &= ~0x0010;
-
-    if(pAbility->act_tx == ENABLED)
-        regData |= 0x0020;
-    else
-        regData &= ~0x0020;
-
-    regData |= (0x0001 << 6);
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_LED0_DATA_CTRL + (rtk_uint32)group, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_groupAbility_get
- * Description:
- *      Get per group Led ability
- * Input:
- *      group    - LED group.
- *      pAbility - LED ability
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      None.
- */
-
-rtk_api_ret_t rtk_led_groupAbility_get(rtk_led_group_t group, rtk_led_ability_t *pAbility)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (LED_GROUP_END <= group)
-        return RT_ERR_FAILED;
-
-    if(pAbility == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_LED0_DATA_CTRL + (rtk_uint32)group, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    pAbility->link_10m = (regData & 0x0001) ? ENABLED : DISABLED;
-    pAbility->link_100m = (regData & 0x0002) ? ENABLED : DISABLED;
-    pAbility->link_500m = (regData & 0x0004) ? ENABLED : DISABLED;
-    pAbility->link_1000m = (regData & 0x0008) ? ENABLED : DISABLED;
-    pAbility->act_rx = (regData & 0x0010) ? ENABLED : DISABLED;
-    pAbility->act_tx = (regData & 0x0020) ? ENABLED : DISABLED;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_led_serialMode_set
- * Description:
- *      Set Led serial mode active congiuration
- * Input:
- *      active - LED group.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set LED serial mode active congiuration.
- */
-rtk_api_ret_t rtk_led_serialMode_set(rtk_led_active_t active)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ( active >= LED_ACTIVE_END)
-        return RT_ERR_INPUT;
-
-     if ((retVal = rtl8367c_setAsicLedSerialModeConfig(active,1))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_serialMode_get
- * Description:
- *      Get Led group congiuration mode
- * Input:
- *      group - LED group.
- * Output:
- *      pConfig - LED configuration.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *       The API can get LED serial mode active configuration.
- */
-rtk_api_ret_t rtk_led_serialMode_get(rtk_led_active_t *pActive)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pActive)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLedSerialModeConfig(pActive,&regData))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_OutputEnable_set
- * Description:
- *      This API set LED I/O state.
- * Input:
- *      enabled     - LED I/O state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set LED I/O state.
- */
-rtk_api_ret_t rtk_led_OutputEnable_set(rtk_enable_t state)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (state >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicLedOutputEnable(state))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_OutputEnable_get
- * Description:
- *      This API get LED I/O state.
- * Input:
- *      None.
- * Output:
- *      pEnabled        - LED I/O state
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set current LED I/O  state.
- */
-rtk_api_ret_t rtk_led_OutputEnable_get(rtk_enable_t *pState)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(pState == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLedOutputEnable(pState))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_led_serialModePortmask_set
- * Description:
- *      This API configure Serial LED output Group and portmask
- * Input:
- *      output          - output group
- *      pPortmask       - output portmask
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_led_serialModePortmask_set(rtk_led_serialOutput_t output, rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(output >= SERIAL_LED_END)
-        return RT_ERR_INPUT;
-
-    if(pPortmask == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtk_switch_portmask_L2P_get(pPortmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicLedSerialOutput((rtk_uint32)output, pmask))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_led_serialModePortmask_get
- * Description:
- *      This API get Serial LED output Group and portmask
- * Input:
- *      None.
- * Output:
- *      pOutput         - output group
- *      pPortmask       - output portmask
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_led_serialModePortmask_get(rtk_led_serialOutput_t *pOutput, rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(pOutput == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(pPortmask == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicLedSerialOutput((rtk_uint32 *)pOutput, &pmask))!=RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/mirror.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/mirror.c
deleted file mode 100644
index 1921d1a5af..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/mirror.c
+++ /dev/null
@@ -1,548 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in Mirror module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <mirror.h>
-#include <string.h>
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_mirror.h>
-
-/* Function Name:
- *      rtk_mirror_portBased_set
- * Description:
- *      Set port mirror function.
- * Input:
- *      mirroring_port          - Monitor port.
- *      pMirrored_rx_portmask   - Rx mirror port mask.
- *      pMirrored_tx_portmask   - Tx mirror port mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      The API is to set mirror function of source port and mirror port.
- *      The mirror port can only be set to one port and the TX and RX mirror ports
- *      should be identical.
- */
-rtk_api_ret_t rtk_mirror_portBased_set(rtk_port_t mirroring_port, rtk_portmask_t *pMirrored_rx_portmask, rtk_portmask_t *pMirrored_tx_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_enable_t mirRx, mirTx;
-    rtk_uint32 i, pmask;
-    rtk_port_t source_port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(mirroring_port);
-
-    if(NULL == pMirrored_rx_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pMirrored_tx_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    RTK_CHK_PORTMASK_VALID(pMirrored_rx_portmask);
-
-    RTK_CHK_PORTMASK_VALID(pMirrored_tx_portmask);
-
-    /*Mirror Sorce Port Mask Check*/
-    if (pMirrored_tx_portmask->bits[0]!=pMirrored_rx_portmask->bits[0]&&pMirrored_tx_portmask->bits[0]!=0&&pMirrored_rx_portmask->bits[0]!=0)
-        return RT_ERR_PORT_MASK;
-
-     /*mirror port != source port*/
-    if(RTK_PORTMASK_IS_PORT_SET((*pMirrored_tx_portmask), mirroring_port) || RTK_PORTMASK_IS_PORT_SET((*pMirrored_rx_portmask), mirroring_port))
-        return RT_ERR_PORT_MASK;
-
-    source_port = rtk_switch_maxLogicalPort_get();
-
-    RTK_SCAN_ALL_LOG_PORT(i)
-    {
-        if (pMirrored_tx_portmask->bits[0]&(1<<i))
-        {
-            source_port = i;
-            break;
-        }
-
-        if (pMirrored_rx_portmask->bits[0]&(1<<i))
-        {
-            source_port = i;
-            break;
-        }
-    }
-
-    if ((retVal = rtl8367c_setAsicPortMirror(rtk_switch_port_L2P_get(source_port), rtk_switch_port_L2P_get(mirroring_port))) != RT_ERR_OK)
-        return retVal;
-    if(pMirrored_rx_portmask->bits[0] != 0)
-    {
-        if ((retVal = rtk_switch_portmask_L2P_get(pMirrored_rx_portmask, &pmask)) != RT_ERR_OK)
-            return retVal;
-        if ((retVal = rtl8367c_setAsicPortMirrorMask(pmask)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        if ((retVal = rtk_switch_portmask_L2P_get(pMirrored_tx_portmask, &pmask)) != RT_ERR_OK)
-            return retVal;
-        if ((retVal = rtl8367c_setAsicPortMirrorMask(pmask)) != RT_ERR_OK)
-            return retVal;
-    }
-
-
-    if (pMirrored_rx_portmask->bits[0])
-        mirRx = ENABLED;
-    else
-        mirRx = DISABLED;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorRxFunction(mirRx)) != RT_ERR_OK)
-        return retVal;
-
-    if (pMirrored_tx_portmask->bits[0])
-        mirTx = ENABLED;
-    else
-        mirTx = DISABLED;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorTxFunction(mirTx)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_mirror_portBased_get
- * Description:
- *      Get port mirror function.
- * Input:
- *      None
- * Output:
- *      pMirroring_port         - Monitor port.
- *      pMirrored_rx_portmask   - Rx mirror port mask.
- *      pMirrored_tx_portmask   - Tx mirror port mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror function of source port and mirror port.
- */
-rtk_api_ret_t rtk_mirror_portBased_get(rtk_port_t *pMirroring_port, rtk_portmask_t *pMirrored_rx_portmask, rtk_portmask_t *pMirrored_tx_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_port_t source_port;
-    rtk_enable_t mirRx, mirTx;
-    rtk_uint32 sport, mport, pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMirrored_rx_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pMirrored_tx_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pMirroring_port)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortMirror(&sport, &mport)) != RT_ERR_OK)
-        return retVal;
-    source_port = rtk_switch_port_P2L_get(sport);
-    *pMirroring_port = rtk_switch_port_P2L_get(mport);
-
-    if ((retVal = rtl8367c_getAsicPortMirrorRxFunction((rtk_uint32*)&mirRx)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorTxFunction((rtk_uint32*)&mirTx)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorMask(&pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if (DISABLED == mirRx)
-        pMirrored_rx_portmask->bits[0]=0;
-    else
-    {
-        if ((retVal = rtk_switch_portmask_P2L_get(pmask, pMirrored_rx_portmask)) != RT_ERR_OK)
-            return retVal;
-        pMirrored_rx_portmask->bits[0] |= 1<<source_port;
-    }
-
-     if (DISABLED == mirTx)
-        pMirrored_tx_portmask->bits[0]=0;
-    else
-    {
-        if ((retVal = rtk_switch_portmask_P2L_get(pmask, pMirrored_tx_portmask)) != RT_ERR_OK)
-            return retVal;
-        pMirrored_tx_portmask->bits[0] |= 1<<source_port;
-    }
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_mirror_portIso_set
- * Description:
- *      Set mirror port isolation.
- * Input:
- *      enable |Mirror isolation status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set mirror isolation function that prevent normal forwarding packets to miror port.
- */
-rtk_api_ret_t rtk_mirror_portIso_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorIsolation(enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_portIso_get
- * Description:
- *      Get mirror port isolation.
- * Input:
- *      None
- * Output:
- *      pEnable |Mirror isolation status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror isolation status.
- */
-rtk_api_ret_t rtk_mirror_portIso_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorIsolation(pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_vlanLeaky_set
- * Description:
- *      Set mirror VLAN leaky.
- * Input:
- *      txenable -TX leaky enable.
- *      rxenable - RX leaky enable.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set mirror VLAN leaky function forwarding packets to miror port.
- */
-rtk_api_ret_t rtk_mirror_vlanLeaky_set(rtk_enable_t txenable, rtk_enable_t rxenable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((txenable >= RTK_ENABLE_END) ||(rxenable >= RTK_ENABLE_END))
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorVlanTxLeaky(txenable)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorVlanRxLeaky(rxenable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_vlanLeaky_get
- * Description:
- *      Get mirror VLAN leaky.
- * Input:
- *      None
- * Output:
- *      pTxenable - TX leaky enable.
- *      pRxenable - RX leaky enable.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror VLAN leaky status.
- */
-rtk_api_ret_t rtk_mirror_vlanLeaky_get(rtk_enable_t *pTxenable, rtk_enable_t *pRxenable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if( (NULL == pTxenable) || (NULL == pRxenable) )
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorVlanTxLeaky(pTxenable)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorVlanRxLeaky(pRxenable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_isolationLeaky_set
- * Description:
- *      Set mirror Isolation leaky.
- * Input:
- *      txenable -TX leaky enable.
- *      rxenable - RX leaky enable.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set mirror VLAN leaky function forwarding packets to miror port.
- */
-rtk_api_ret_t rtk_mirror_isolationLeaky_set(rtk_enable_t txenable, rtk_enable_t rxenable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((txenable >= RTK_ENABLE_END) ||(rxenable >= RTK_ENABLE_END))
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorIsolationTxLeaky(txenable)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorIsolationRxLeaky(rxenable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_isolationLeaky_get
- * Description:
- *      Get mirror isolation leaky.
- * Input:
- *      None
- * Output:
- *      pTxenable - TX leaky enable.
- *      pRxenable - RX leaky enable.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror isolation leaky status.
- */
-rtk_api_ret_t rtk_mirror_isolationLeaky_get(rtk_enable_t *pTxenable, rtk_enable_t *pRxenable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if( (NULL == pTxenable) || (NULL == pRxenable) )
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorIsolationTxLeaky(pTxenable)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorIsolationRxLeaky(pRxenable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_keep_set
- * Description:
- *      Set mirror packet format keep.
- * Input:
- *      mode - -mirror keep mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The API is to set  -mirror keep mode.
- *      The mirror keep mode is as following:
- *      - MIRROR_FOLLOW_VLAN
- *      - MIRROR_KEEP_ORIGINAL
- *      - MIRROR_KEEP_END
- */
-rtk_api_ret_t rtk_mirror_keep_set(rtk_mirror_keep_t mode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (mode >= MIRROR_KEEP_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorRealKeep(mode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_keep_get
- * Description:
- *      Get mirror packet format keep.
- * Input:
- *      None
- * Output:
- *      pMode -mirror keep mode.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API is to get mirror keep mode.
-  *      The mirror keep mode is as following:
- *      - MIRROR_FOLLOW_VLAN
- *      - MIRROR_KEEP_ORIGINAL
- *      - MIRROR_KEEP_END
- */
-rtk_api_ret_t rtk_mirror_keep_get(rtk_mirror_keep_t *pMode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMode)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorRealKeep(pMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_override_set
- * Description:
- *      Set port mirror override function.
- * Input:
- *      rxMirror        - 1: output mirrored packet, 0: output normal forward packet
- *      txMirror        - 1: output mirrored packet, 0: output normal forward packet
- *      aclMirror       - 1: output mirrored packet, 0: output normal forward packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API is to set mirror override function.
- *      This function control the output format when a port output
- *      normal forward & mirrored packet at the same time.
- */
-rtk_api_ret_t rtk_mirror_override_set(rtk_enable_t rxMirror, rtk_enable_t txMirror, rtk_enable_t aclMirror)
-{
-    rtk_api_ret_t retVal;
-
-    if( (rxMirror >= RTK_ENABLE_END) || (txMirror >= RTK_ENABLE_END) || (aclMirror >= RTK_ENABLE_END))
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortMirrorOverride((rtk_uint32)rxMirror, (rtk_uint32)txMirror, (rtk_uint32)aclMirror)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_mirror_override_get
- * Description:
- *      Get port mirror override function.
- * Input:
- *      None
- * Output:
- *      pRxMirror       - 1: output mirrored packet, 0: output normal forward packet
- *      pTxMirror       - 1: output mirrored packet, 0: output normal forward packet
- *      pAclMirror      - 1: output mirrored packet, 0: output normal forward packet
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Null Pointer
- * Note:
- *      The API is to Get mirror override function.
- *      This function control the output format when a port output
- *      normal forward & mirrored packet at the same time.
- */
-rtk_api_ret_t rtk_mirror_override_get(rtk_enable_t *pRxMirror, rtk_enable_t *pTxMirror, rtk_enable_t *pAclMirror)
-{
-    rtk_api_ret_t retVal;
-
-    if( (pRxMirror == NULL) || (pTxMirror == NULL) || (pAclMirror == NULL))
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_getAsicPortMirrorOverride((rtk_uint32 *)pRxMirror, (rtk_uint32 *)pTxMirror, (rtk_uint32 *)pAclMirror)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/oam.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/oam.c
deleted file mode 100644
index dc1559ae3e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/oam.c
+++ /dev/null
@@ -1,245 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in OAM(802.3ah)  module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <oam.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_oam.h>
-
-
-/* Module Name : OAM */
-
-/* Function Name:
- *      rtk_oam_init
- * Description:
- *      Initialize oam module.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- * Note:
- *      Must initialize oam module before calling any oam APIs.
- */
-rtk_api_ret_t rtk_oam_init(void)
-{
-    return RT_ERR_OK;
-} /* end of rtk_oam_init */
-
-
-/* Function Name:
- *      rtk_oam_state_set
- * Description:
- *      This API set OAM state.
- * Input:
- *      enabled     -OAMstate
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set OAM state.
- */
-rtk_api_ret_t rtk_oam_state_set(rtk_enable_t enabled)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enabled >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicOamEnable(enabled))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_oam_state_get
- * Description:
- *      This API get OAM state.
- * Input:
- *      None.
- * Output:
- *      pEnabled        - H/W IGMP state
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT           - Error parameter
- * Note:
- *      This API set current OAM state.
- */
-rtk_api_ret_t rtk_oam_state_get(rtk_enable_t *pEnabled)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicOamEnable(pEnabled))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
-/* Function Name:
- *      rtk_oam_parserAction_set
- * Description:
- *      Set OAM parser action
- * Input:
- *      port    - port id
- *      action  - parser action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-rtk_api_ret_t  rtk_oam_parserAction_set(rtk_port_t port, rtk_oam_parser_act_t action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (action >= OAM_PARSER_ACTION_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicOamParser(rtk_switch_port_L2P_get(port), action))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_oam_parserAction_set
- * Description:
- *      Get OAM parser action
- * Input:
- *      port    - port id
- * Output:
- *      pAction  - parser action
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-rtk_api_ret_t  rtk_oam_parserAction_get(rtk_port_t port, rtk_oam_parser_act_t *pAction)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicOamParser(rtk_switch_port_L2P_get(port), pAction))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_oam_multiplexerAction_set
- * Description:
- *      Set OAM multiplexer action
- * Input:
- *      port    - port id
- *      action  - parser action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-rtk_api_ret_t  rtk_oam_multiplexerAction_set(rtk_port_t port, rtk_oam_multiplexer_act_t action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (action >= OAM_MULTIPLEXER_ACTION_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicOamMultiplexer(rtk_switch_port_L2P_get(port), action))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_oam_parserAction_set
- * Description:
- *      Get OAM multiplexer action
- * Input:
- *      port    - port id
- * Output:
- *      pAction  - parser action
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- * Note:
- *      None
- */
-rtk_api_ret_t  rtk_oam_multiplexerAction_get(rtk_port_t port, rtk_oam_multiplexer_act_t *pAction)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicOamMultiplexer(rtk_switch_port_L2P_get(port), pAction))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/port.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/port.c
deleted file mode 100644
index 9f99d1b3dc..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/port.c
+++ /dev/null
@@ -1,2467 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in Port module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <port.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_port.h>
-#include <rtl8367c_asicdrv_misc.h>
-#include <rtl8367c_asicdrv_portIsolation.h>
-
-#define FIBER_INIT_SIZE 1507
-CONST_T rtk_uint8 Fiber[FIBER_INIT_SIZE] = {
-0x02,0x04,0x41,0xE4,0xF5,0xA8,0xD2,0xAF,
-0x22,0x00,0x00,0x02,0x05,0x2D,0xE4,0x90,
-0x06,0x2A,0xF0,0xFD,0x7C,0x01,0x7F,0x3F,
-0x7E,0x1D,0x12,0x05,0xAF,0x7D,0x40,0x12,
-0x02,0x5F,0xE4,0xFF,0xFE,0xFD,0x80,0x08,
-0x12,0x05,0x9E,0x50,0x0C,0x12,0x05,0x8B,
-0xFC,0x90,0x06,0x24,0x12,0x03,0x76,0x80,
-0xEF,0xE4,0xF5,0xA8,0xD2,0xAF,0x7D,0x1F,
-0xFC,0x7F,0x49,0x7E,0x13,0x12,0x05,0xAF,
-0x12,0x05,0xD6,0x7D,0xD7,0x12,0x02,0x1E,
-0x7D,0x80,0x12,0x01,0xCA,0x7D,0x94,0x7C,
-0xF9,0x12,0x02,0x3B,0x7D,0x81,0x12,0x01,
-0xCA,0x7D,0xA2,0x7C,0x31,0x12,0x02,0x3B,
-0x7D,0x82,0x12,0x01,0xDF,0x7D,0x60,0x7C,
-0x69,0x12,0x02,0x43,0x7D,0x83,0x12,0x01,
-0xDF,0x7D,0x28,0x7C,0x97,0x12,0x02,0x43,
-0x7D,0x84,0x12,0x01,0xF4,0x7D,0x85,0x7C,
-0x9D,0x12,0x02,0x57,0x7D,0x23,0x12,0x01,
-0xF4,0x7D,0x10,0x7C,0xD8,0x12,0x02,0x57,
-0x7D,0x24,0x7C,0x04,0x12,0x02,0x28,0x7D,
-0x00,0x12,0x02,0x1E,0x7D,0x2F,0x12,0x02,
-0x09,0x7D,0x20,0x7C,0x0F,0x7F,0x02,0x7E,
-0x66,0x12,0x05,0xAF,0x7D,0x01,0x12,0x02,
-0x09,0x7D,0x04,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x05,0xAF,0x7D,0x80,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x05,0xAF,0x7F,
-0x02,0x7E,0x66,0x12,0x02,0x4B,0x44,0x02,
-0xFF,0x90,0x06,0x28,0xEE,0xF0,0xA3,0xEF,
-0xF0,0x44,0x04,0xFF,0x90,0x06,0x28,0xEE,
-0xF0,0xFC,0xA3,0xEF,0xF0,0xFD,0x7F,0x02,
-0x7E,0x66,0x12,0x05,0xAF,0x7D,0x04,0x7C,
-0x00,0x12,0x02,0x28,0x7D,0xB9,0x7C,0x15,
-0x7F,0xEB,0x7E,0x13,0x12,0x05,0xAF,0x7D,
-0x07,0x7C,0x00,0x7F,0xE7,0x7E,0x13,0x12,
-0x05,0xAF,0x7D,0x40,0x7C,0x11,0x7F,0x00,
-0x7E,0x62,0x12,0x05,0xAF,0x12,0x03,0x82,
-0x7D,0x41,0x12,0x02,0x5F,0xE4,0xFF,0xFE,
-0xFD,0x80,0x08,0x12,0x05,0x9E,0x50,0x0C,
-0x12,0x05,0x8B,0xFC,0x90,0x06,0x24,0x12,
-0x03,0x76,0x80,0xEF,0xC2,0x00,0xC2,0x01,
-0xD2,0xA9,0xD2,0x8C,0x7F,0x01,0x7E,0x62,
-0x12,0x02,0x4B,0x30,0xE2,0x05,0xE4,0xA3,
-0xF0,0x80,0xF1,0x90,0x06,0x2A,0xE0,0x70,
-0x12,0x12,0x01,0x89,0x90,0x06,0x2A,0x74,
-0x01,0xF0,0xE4,0x90,0x06,0x2D,0xF0,0xA3,
-0xF0,0x80,0xD9,0xC3,0x90,0x06,0x2E,0xE0,
-0x94,0x64,0x90,0x06,0x2D,0xE0,0x94,0x00,
-0x40,0xCA,0xE4,0xF0,0xA3,0xF0,0x12,0x01,
-0x89,0x90,0x06,0x2A,0x74,0x01,0xF0,0x80,
-0xBB,0x7D,0x04,0xFC,0x7F,0x02,0x7E,0x66,
-0x12,0x05,0xAF,0x7D,0x00,0x7C,0x04,0x7F,
-0x01,0x7E,0x66,0x12,0x05,0xAF,0x7D,0xC0,
-0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,0x05,
-0xAF,0xE4,0xFD,0xFC,0x7F,0x02,0x7E,0x66,
-0x12,0x05,0xAF,0x7D,0x00,0x7C,0x04,0x7F,
-0x01,0x7E,0x66,0x12,0x05,0xAF,0x7D,0xC0,
-0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,0x05,
-0xAF,0x22,0x7C,0x04,0x7F,0x01,0x7E,0x66,
-0x12,0x05,0xAF,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x12,0x05,0xAF,0x22,0x7C,
-0x04,0x7F,0x01,0x7E,0x66,0x12,0x05,0xAF,
-0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,
-0x12,0x05,0xAF,0x22,0x7C,0x04,0x7F,0x01,
-0x7E,0x66,0x12,0x05,0xAF,0x7D,0xC0,0x7C,
-0x00,0x7F,0x00,0x7E,0x66,0x12,0x05,0xAF,
-0x22,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x05,0xAF,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x05,0xAF,0x22,0x7C,0x04,
-0x7F,0x02,0x7E,0x66,0x12,0x05,0xAF,0x22,
-0x7F,0x01,0x7E,0x66,0x12,0x05,0xAF,0x7D,
-0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,
-0x05,0xAF,0x22,0x7F,0x02,0x7E,0x66,0x12,
-0x05,0xAF,0x22,0x7F,0x02,0x7E,0x66,0x12,
-0x05,0xAF,0x22,0x12,0x05,0x67,0x90,0x06,
-0x28,0xEE,0xF0,0xA3,0xEF,0xF0,0x22,0x7F,
-0x02,0x7E,0x66,0x12,0x05,0xAF,0x22,0x7C,
-0x00,0x7F,0x36,0x7E,0x13,0x12,0x05,0xAF,
-0x22,0xC5,0xF0,0xF8,0xA3,0xE0,0x28,0xF0,
-0xC5,0xF0,0xF8,0xE5,0x82,0x15,0x82,0x70,
-0x02,0x15,0x83,0xE0,0x38,0xF0,0x22,0x75,
-0xF0,0x08,0x75,0x82,0x00,0xEF,0x2F,0xFF,
-0xEE,0x33,0xFE,0xCD,0x33,0xCD,0xCC,0x33,
-0xCC,0xC5,0x82,0x33,0xC5,0x82,0x9B,0xED,
-0x9A,0xEC,0x99,0xE5,0x82,0x98,0x40,0x0C,
-0xF5,0x82,0xEE,0x9B,0xFE,0xED,0x9A,0xFD,
-0xEC,0x99,0xFC,0x0F,0xD5,0xF0,0xD6,0xE4,
-0xCE,0xFB,0xE4,0xCD,0xFA,0xE4,0xCC,0xF9,
-0xA8,0x82,0x22,0xB8,0x00,0xC1,0xB9,0x00,
-0x59,0xBA,0x00,0x2D,0xEC,0x8B,0xF0,0x84,
-0xCF,0xCE,0xCD,0xFC,0xE5,0xF0,0xCB,0xF9,
-0x78,0x18,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xED,0x33,0xFD,0xEC,0x33,0xFC,0xEB,0x33,
-0xFB,0x10,0xD7,0x03,0x99,0x40,0x04,0xEB,
-0x99,0xFB,0x0F,0xD8,0xE5,0xE4,0xF9,0xFA,
-0x22,0x78,0x18,0xEF,0x2F,0xFF,0xEE,0x33,
-0xFE,0xED,0x33,0xFD,0xEC,0x33,0xFC,0xC9,
-0x33,0xC9,0x10,0xD7,0x05,0x9B,0xE9,0x9A,
-0x40,0x07,0xEC,0x9B,0xFC,0xE9,0x9A,0xF9,
-0x0F,0xD8,0xE0,0xE4,0xC9,0xFA,0xE4,0xCC,
-0xFB,0x22,0x75,0xF0,0x10,0xEF,0x2F,0xFF,
-0xEE,0x33,0xFE,0xED,0x33,0xFD,0xCC,0x33,
-0xCC,0xC8,0x33,0xC8,0x10,0xD7,0x07,0x9B,
-0xEC,0x9A,0xE8,0x99,0x40,0x0A,0xED,0x9B,
-0xFD,0xEC,0x9A,0xFC,0xE8,0x99,0xF8,0x0F,
-0xD5,0xF0,0xDA,0xE4,0xCD,0xFB,0xE4,0xCC,
-0xFA,0xE4,0xC8,0xF9,0x22,0xEB,0x9F,0xF5,
-0xF0,0xEA,0x9E,0x42,0xF0,0xE9,0x9D,0x42,
-0xF0,0xE8,0x9C,0x45,0xF0,0x22,0xE0,0xFC,
-0xA3,0xE0,0xFD,0xA3,0xE0,0xFE,0xA3,0xE0,
-0xFF,0x22,0xE0,0xF8,0xA3,0xE0,0xF9,0xA3,
-0xE0,0xFA,0xA3,0xE0,0xFB,0x22,0xEC,0xF0,
-0xA3,0xED,0xF0,0xA3,0xEE,0xF0,0xA3,0xEF,
-0xF0,0x22,0x12,0x03,0xF8,0x12,0x04,0x1A,
-0x44,0x40,0x12,0x04,0x0F,0x7D,0x03,0x7C,
-0x00,0x12,0x04,0x23,0x12,0x05,0xAF,0x12,
-0x03,0xF8,0x12,0x04,0x1A,0x54,0xBF,0x12,
-0x04,0x0F,0x7D,0x03,0x7C,0x00,0x12,0x03,
-0xD0,0x7F,0x02,0x7E,0x66,0x12,0x05,0x67,
-0xEF,0x54,0xFD,0x54,0xFE,0x12,0x04,0x33,
-0x12,0x03,0xD0,0x7F,0x02,0x7E,0x66,0x12,
-0x05,0x67,0xEF,0x44,0x02,0x44,0x01,0x12,
-0x04,0x33,0x12,0x04,0x23,0x02,0x05,0xAF,
-0x7F,0x01,0x7E,0x66,0x12,0x05,0xAF,0x7D,
-0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,
-0x05,0xAF,0xE4,0xFD,0xFC,0x7F,0x01,0x7E,
-0x66,0x12,0x05,0xAF,0x7D,0x80,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x05,0xAF,0x22,
-0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,0x66,
-0x12,0x05,0xAF,0x7D,0x80,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x12,0x05,0xAF,0x22,0xFD,
-0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,0x05,
-0xAF,0x22,0x7F,0x02,0x7E,0x66,0x12,0x05,
-0x67,0xEF,0x22,0x7F,0x01,0x7E,0x66,0x12,
-0x05,0xAF,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x22,0xFD,0xAC,0x06,0x7F,0x02,
-0x7E,0x66,0x12,0x05,0xAF,0xE4,0xFD,0xFC,
-0x22,0x78,0x7F,0xE4,0xF6,0xD8,0xFD,0x75,
-0x81,0x3C,0x02,0x04,0x88,0x02,0x00,0x0E,
-0xE4,0x93,0xA3,0xF8,0xE4,0x93,0xA3,0x40,
-0x03,0xF6,0x80,0x01,0xF2,0x08,0xDF,0xF4,
-0x80,0x29,0xE4,0x93,0xA3,0xF8,0x54,0x07,
-0x24,0x0C,0xC8,0xC3,0x33,0xC4,0x54,0x0F,
-0x44,0x20,0xC8,0x83,0x40,0x04,0xF4,0x56,
-0x80,0x01,0x46,0xF6,0xDF,0xE4,0x80,0x0B,
-0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80,
-0x90,0x05,0xCB,0xE4,0x7E,0x01,0x93,0x60,
-0xBC,0xA3,0xFF,0x54,0x3F,0x30,0xE5,0x09,
-0x54,0x1F,0xFE,0xE4,0x93,0xA3,0x60,0x01,
-0x0E,0xCF,0x54,0xC0,0x25,0xE0,0x60,0xA8,
-0x40,0xB8,0xE4,0x93,0xA3,0xFA,0xE4,0x93,
-0xA3,0xF8,0xE4,0x93,0xA3,0xC8,0xC5,0x82,
-0xC8,0xCA,0xC5,0x83,0xCA,0xF0,0xA3,0xC8,
-0xC5,0x82,0xC8,0xCA,0xC5,0x83,0xCA,0xDF,
-0xE9,0xDE,0xE7,0x80,0xBE,0x75,0x0F,0x80,
-0x75,0x0E,0x7E,0x75,0x0D,0xAA,0x75,0x0C,
-0x83,0xE4,0xF5,0x10,0x75,0x0B,0xA0,0x75,
-0x0A,0xAC,0x75,0x09,0xB9,0x75,0x08,0x03,
-0x75,0x89,0x11,0x7B,0x60,0x7A,0x09,0xF9,
-0xF8,0xAF,0x0B,0xAE,0x0A,0xAD,0x09,0xAC,
-0x08,0x12,0x02,0xBB,0xAD,0x07,0xAC,0x06,
-0xC3,0xE4,0x9D,0xFD,0xE4,0x9C,0xFC,0x78,
-0x17,0xF6,0xAF,0x05,0xEF,0x08,0xF6,0x18,
-0xE6,0xF5,0x8C,0x08,0xE6,0xF5,0x8A,0x74,
-0x0D,0x2D,0xFD,0xE4,0x3C,0x18,0xF6,0xAF,
-0x05,0xEF,0x08,0xF6,0x75,0x88,0x10,0x53,
-0x8E,0xC7,0xD2,0xA9,0x22,0xC0,0xE0,0xC0,
-0xF0,0xC0,0x83,0xC0,0x82,0xC0,0xD0,0x75,
-0xD0,0x00,0xC0,0x00,0x78,0x17,0xE6,0xF5,
-0x8C,0x78,0x18,0xE6,0xF5,0x8A,0x90,0x06,
-0x2B,0xE4,0x75,0xF0,0x01,0x12,0x02,0x69,
-0x90,0x06,0x2D,0xE4,0x75,0xF0,0x01,0x12,
-0x02,0x69,0xD0,0x00,0xD0,0xD0,0xD0,0x82,
-0xD0,0x83,0xD0,0xF0,0xD0,0xE0,0x32,0xC2,
-0xAF,0xAD,0x07,0xAC,0x06,0x8C,0xA2,0x8D,
-0xA3,0x75,0xA0,0x01,0x00,0x00,0x00,0x00,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xAE,
-0xA1,0xBE,0x00,0xF0,0xAE,0xA6,0xAF,0xA7,
-0xD2,0xAF,0x22,0x90,0x06,0x24,0x12,0x03,
-0x5E,0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,
-0xE4,0x3D,0xFD,0xE4,0x3C,0x22,0xE4,0x7F,
-0x20,0x7E,0x4E,0xFD,0xFC,0x90,0x06,0x24,
-0x12,0x03,0x6A,0xC3,0x02,0x03,0x4D,0xC2,
-0xAF,0xAB,0x07,0xAA,0x06,0x8A,0xA2,0x8B,
-0xA3,0x8C,0xA4,0x8D,0xA5,0x75,0xA0,0x03,
-0x00,0x00,0x00,0xAA,0xA1,0xBA,0x00,0xF8,
-0xD2,0xAF,0x22,0x42,0x06,0x2D,0x00,0x00,
-0x42,0x06,0x2B,0x00,0x00,0x00,0x12,0x05,
-0xDF,0x12,0x04,0xCD,0x02,0x00,0x03,0xE4,
-0xF5,0x8E,0x22};
-
-static rtk_api_ret_t _rtk_port_FiberModeAbility_set(rtk_port_t port, rtk_port_phy_ability_t *pAbility)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-
-    /* Check Combo port or not */
-    RTK_CHK_PORT_IS_COMBO(port);
-
-    /* Flow Control */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_FIB0_CFG04, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if (pAbility->AsyFC == 1)
-        regData |= (0x0001 << 8);
-    else
-        regData &= ~(0x0001 << 8);
-
-    if (pAbility->FC == 1)
-        regData |= (0x0001 << 7);
-    else
-        regData &= ~(0x0001 << 7);
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_FIB0_CFG04, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /* Speed ability */
-    if( (pAbility->Full_1000 == 1) && (pAbility->Full_100 == 1) && (pAbility->AutoNegotiation == 1) )
-    {
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_FRC_MODE_OFFSET, 0)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_MODE_MASK, 7)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_FIB0_CFG00, 0x1140)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if(pAbility->Full_1000 == 1)
-    {
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_FRC_MODE_OFFSET, 1)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_MODE_MASK, 4)) != RT_ERR_OK)
-            return retVal;
-
-        if(pAbility->AutoNegotiation == 1)
-        {
-            if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_FIB0_CFG00, 0x1140)) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-        {
-            if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_FIB0_CFG00, 0x0140)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-    else if(pAbility->Full_100 == 1)
-    {
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_FRC_MODE_OFFSET, 1)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_MODE_MASK, 5)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_FIB0_CFG00, 0x2100)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /* Digital software reset */
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, 0x0003)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x0080)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_SDS_INDACS_DATA, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    regData |= (0x0001 << 6);
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, regData)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, 0x0003)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-        return retVal;
-
-    regData &= ~(0x0001 << 6);
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, regData)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, 0x0003)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-        return retVal;
-
-    /* CDR reset */
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x1401))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, 0x0000))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x1403))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, 0x0000))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-static rtk_api_ret_t _rtk_port_FiberModeAbility_get(rtk_port_t port, rtk_port_phy_ability_t *pAbility)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      data, regData;
-
-    /* Check Combo port or not */
-    RTK_CHK_PORT_IS_COMBO(port);
-
-    memset(pAbility, 0x00, sizeof(rtk_port_phy_ability_t));
-
-    /* Flow Control */
-    if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_FRC_REG4_OFFSET, 1)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_FRC_REG4_FIB100_OFFSET, 0)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, 0x0044)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x0080)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_SDS_INDACS_DATA, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(regData & (0x0001 << 8))
-        pAbility->AsyFC = 1;
-
-    if(regData & (0x0001 << 7))
-        pAbility->FC = 1;
-
-    /* Speed ability */
-    if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_FRC_MODE_OFFSET, &data)) != RT_ERR_OK)
-            return retVal;
-
-    if(data == 0)
-    {
-        pAbility->AutoNegotiation = 1;
-        pAbility->Full_1000 = 1;
-        pAbility->Full_100 = 1;
-    }
-    else
-    {
-        if ((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FIBER_CFG_1, RTL8367C_SDS_MODE_MASK, &data)) != RT_ERR_OK)
-            return retVal;
-
-        if(data == 4)
-        {
-            pAbility->Full_1000 = 1;
-
-            if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_FIB0_CFG00, &data)) != RT_ERR_OK)
-                return retVal;
-
-            if(data & 0x1000)
-                pAbility->AutoNegotiation = 1;
-            else
-                pAbility->AutoNegotiation = 0;
-        }
-        else if(data == 5)
-            pAbility->Full_100 = 1;
-        else
-            return RT_ERR_FAILED;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyAutoNegoAbility_set
- * Description:
- *      Set ethernet PHY auto-negotiation desired ability.
- * Input:
- *      port        - port id.
- *      pAbility    - Ability structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      If Full_1000 bit is set to 1, the AutoNegotiation will be automatic set to 1. While both AutoNegotiation and Full_1000 are set to 0, the PHY speed and duplex selection will
- *      be set as following 100F > 100H > 10F > 10H priority sequence.
- */
-rtk_api_ret_t rtk_port_phyAutoNegoAbility_set(rtk_port_t port, rtk_port_phy_ability_t *pAbility)
-{
-    rtk_api_ret_t       retVal;
-    rtk_uint32          phyData;
-    rtk_uint32          phyEnMsk0;
-    rtk_uint32          phyEnMsk4;
-    rtk_uint32          phyEnMsk9;
-    rtk_port_media_t    media_type;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if(NULL == pAbility)
-        return RT_ERR_NULL_POINTER;
-
-    if (pAbility->Half_10 >= RTK_ENABLE_END || pAbility->Full_10 >= RTK_ENABLE_END ||
-       pAbility->Half_100 >= RTK_ENABLE_END || pAbility->Full_100 >= RTK_ENABLE_END ||
-       pAbility->Full_1000 >= RTK_ENABLE_END || pAbility->AutoNegotiation >= RTK_ENABLE_END ||
-       pAbility->AsyFC >= RTK_ENABLE_END || pAbility->FC >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (rtk_switch_isComboPort(port) == RT_ERR_OK)
-    {
-        if ((retVal = rtk_port_phyComboPortMedia_get(port, &media_type)) != RT_ERR_OK)
-            return retVal;
-
-        if(media_type == PORT_MEDIA_FIBER)
-        {
-            return _rtk_port_FiberModeAbility_set(port, pAbility);
-        }
-    }
-
-    /*for PHY auto mode setup*/
-    pAbility->AutoNegotiation = 1;
-
-    phyEnMsk0 = 0;
-    phyEnMsk4 = 0;
-    phyEnMsk9 = 0;
-
-    if (1 == pAbility->Half_10)
-    {
-        /*10BASE-TX half duplex capable in reg 4.5*/
-        phyEnMsk4 = phyEnMsk4 | (1 << 5);
-
-        /*Speed selection [1:0] */
-        /* 11=Reserved*/
-        /* 10= 1000Mpbs*/
-        /* 01= 100Mpbs*/
-        /* 00= 10Mpbs*/
-        phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-        phyEnMsk0 = phyEnMsk0 & (~(1 << 13));
-    }
-
-    if (1 == pAbility->Full_10)
-    {
-        /*10BASE-TX full duplex capable in reg 4.6*/
-        phyEnMsk4 = phyEnMsk4 | (1 << 6);
-        /*Speed selection [1:0] */
-        /* 11=Reserved*/
-        /* 10= 1000Mpbs*/
-        /* 01= 100Mpbs*/
-        /* 00= 10Mpbs*/
-        phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-        phyEnMsk0 = phyEnMsk0 & (~(1 << 13));
-
-        /*Full duplex mode in reg 0.8*/
-        phyEnMsk0 = phyEnMsk0 | (1 << 8);
-
-    }
-
-    if (1 == pAbility->Half_100)
-    {
-        /*100BASE-TX half duplex capable in reg 4.7*/
-        phyEnMsk4 = phyEnMsk4 | (1 << 7);
-        /*Speed selection [1:0] */
-        /* 11=Reserved*/
-        /* 10= 1000Mpbs*/
-        /* 01= 100Mpbs*/
-        /* 00= 10Mpbs*/
-        phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-        phyEnMsk0 = phyEnMsk0 | (1 << 13);
-    }
-
-
-    if (1 == pAbility->Full_100)
-    {
-        /*100BASE-TX full duplex capable in reg 4.8*/
-        phyEnMsk4 = phyEnMsk4 | (1 << 8);
-        /*Speed selection [1:0] */
-        /* 11=Reserved*/
-        /* 10= 1000Mpbs*/
-        /* 01= 100Mpbs*/
-        /* 00= 10Mpbs*/
-        phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-        phyEnMsk0 = phyEnMsk0 | (1 << 13);
-        /*Full duplex mode in reg 0.8*/
-        phyEnMsk0 = phyEnMsk0 | (1 << 8);
-    }
-
-
-    if (1 == pAbility->Full_1000)
-    {
-        /*1000 BASE-T FULL duplex capable setting in reg 9.9*/
-        phyEnMsk9 = phyEnMsk9 | (1 << 9);
-
-        /*Speed selection [1:0] */
-        /* 11=Reserved*/
-        /* 10= 1000Mpbs*/
-        /* 01= 100Mpbs*/
-        /* 00= 10Mpbs*/
-        phyEnMsk0 = phyEnMsk0 | (1 << 6);
-        phyEnMsk0 = phyEnMsk0 & (~(1 << 13));
-
-
-        /*Auto-Negotiation setting in reg 0.12*/
-        phyEnMsk0 = phyEnMsk0 | (1 << 12);
-
-     }
-
-    if (1 == pAbility->AutoNegotiation)
-    {
-        /*Auto-Negotiation setting in reg 0.12*/
-        phyEnMsk0 = phyEnMsk0 | (1 << 12);
-    }
-
-    if (1 == pAbility->AsyFC)
-    {
-        /*Asymetric flow control in reg 4.11*/
-        phyEnMsk4 = phyEnMsk4 | (1 << 11);
-    }
-    if (1 == pAbility->FC)
-    {
-        /*Flow control in reg 4.10*/
-        phyEnMsk4 = phyEnMsk4 | (1 << 10);
-    }
-
-    /*1000 BASE-T control register setting*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_1000_BASET_CONTROL_REG, &phyData)) != RT_ERR_OK)
-        return retVal;
-
-    phyData = (phyData & (~0x0200)) | phyEnMsk9 ;
-
-    if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_1000_BASET_CONTROL_REG, phyData)) != RT_ERR_OK)
-        return retVal;
-
-    /*Auto-Negotiation control register setting*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_AN_ADVERTISEMENT_REG, &phyData)) != RT_ERR_OK)
-        return retVal;
-
-    phyData = (phyData & (~0x0DE0)) | phyEnMsk4;
-    if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_AN_ADVERTISEMENT_REG, phyData)) != RT_ERR_OK)
-        return retVal;
-
-    /*Control register setting and restart auto*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, &phyData)) != RT_ERR_OK)
-        return retVal;
-
-    phyData = (phyData & (~0x3140)) | phyEnMsk0;
-    /*If have auto-negotiation capable, then restart auto negotiation*/
-    if (1 == pAbility->AutoNegotiation)
-    {
-        phyData = phyData | (1 << 9);
-    }
-
-    if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, phyData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyAutoNegoAbility_get
- * Description:
- *      Get PHY ability through PHY registers.
- * Input:
- *      port - Port id.
- * Output:
- *      pAbility - Ability structure
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      Get the capablity of specified PHY.
- */
-rtk_api_ret_t rtk_port_phyAutoNegoAbility_get(rtk_port_t port, rtk_port_phy_ability_t *pAbility)
-{
-    rtk_api_ret_t       retVal;
-    rtk_uint32          phyData0;
-    rtk_uint32          phyData4;
-    rtk_uint32          phyData9;
-    rtk_port_media_t    media_type;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if(NULL == pAbility)
-        return RT_ERR_NULL_POINTER;
-
-    if (rtk_switch_isComboPort(port) == RT_ERR_OK)
-    {
-        if ((retVal = rtk_port_phyComboPortMedia_get(port, &media_type)) != RT_ERR_OK)
-            return retVal;
-
-        if(media_type == PORT_MEDIA_FIBER)
-        {
-            return _rtk_port_FiberModeAbility_get(port, pAbility);
-        }
-    }
-
-    /*Control register setting and restart auto*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, &phyData0)) != RT_ERR_OK)
-        return retVal;
-
-    /*Auto-Negotiation control register setting*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_AN_ADVERTISEMENT_REG, &phyData4)) != RT_ERR_OK)
-        return retVal;
-
-    /*1000 BASE-T control register setting*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_1000_BASET_CONTROL_REG, &phyData9)) != RT_ERR_OK)
-        return retVal;
-
-    if (phyData9 & (1 << 9))
-        pAbility->Full_1000 = 1;
-    else
-        pAbility->Full_1000 = 0;
-
-    if (phyData4 & (1 << 11))
-        pAbility->AsyFC = 1;
-    else
-        pAbility->AsyFC = 0;
-
-    if (phyData4 & (1 << 10))
-        pAbility->FC = 1;
-    else
-        pAbility->FC = 0;
-
-
-    if (phyData4 & (1 << 8))
-        pAbility->Full_100 = 1;
-    else
-        pAbility->Full_100 = 0;
-
-    if (phyData4 & (1 << 7))
-        pAbility->Half_100 = 1;
-    else
-        pAbility->Half_100 = 0;
-
-    if (phyData4 & (1 << 6))
-        pAbility->Full_10 = 1;
-    else
-        pAbility->Full_10 = 0;
-
-    if (phyData4 & (1 << 5))
-        pAbility->Half_10 = 1;
-    else
-        pAbility->Half_10 = 0;
-
-
-    if (phyData0 & (1 << 12))
-        pAbility->AutoNegotiation = 1;
-    else
-        pAbility->AutoNegotiation = 0;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyForceModeAbility_set
- * Description:
- *      Set the port speed/duplex mode/pause/asy_pause in the PHY force mode.
- * Input:
- *      port        - port id.
- *      pAbility    - Ability structure
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      While both AutoNegotiation and Full_1000 are set to 0, the PHY speed and duplex selection will
- *      be set as following 100F > 100H > 10F > 10H priority sequence.
- *      This API can be used to configure combo port in fiber mode.
- *      The possible parameters in fiber mode are Full_1000 and Full 100.
- *      All the other fields in rtk_port_phy_ability_t will be ignored in fiber port.
- */
-rtk_api_ret_t rtk_port_phyForceModeAbility_set(rtk_port_t port, rtk_port_phy_ability_t *pAbility)
-{
-     rtk_api_ret_t      retVal;
-     rtk_uint32         phyData;
-     rtk_uint32         phyEnMsk0;
-     rtk_uint32         phyEnMsk4;
-     rtk_uint32         phyEnMsk9;
-     rtk_port_media_t   media_type;
-
-     /* Check initialization state */
-     RTK_CHK_INIT_STATE();
-
-     /* Check Port Valid */
-     RTK_CHK_PORT_IS_UTP(port);
-
-     if(NULL == pAbility)
-        return RT_ERR_NULL_POINTER;
-
-     if (pAbility->Half_10 >= RTK_ENABLE_END || pAbility->Full_10 >= RTK_ENABLE_END ||
-        pAbility->Half_100 >= RTK_ENABLE_END || pAbility->Full_100 >= RTK_ENABLE_END ||
-        pAbility->Full_1000 >= RTK_ENABLE_END || pAbility->AutoNegotiation >= RTK_ENABLE_END ||
-        pAbility->AsyFC >= RTK_ENABLE_END || pAbility->FC >= RTK_ENABLE_END)
-         return RT_ERR_INPUT;
-
-     if (rtk_switch_isComboPort(port) == RT_ERR_OK)
-     {
-         if ((retVal = rtk_port_phyComboPortMedia_get(port, &media_type)) != RT_ERR_OK)
-             return retVal;
-
-         if(media_type == PORT_MEDIA_FIBER)
-         {
-             return _rtk_port_FiberModeAbility_set(port, pAbility);
-         }
-     }
-
-     if (1 == pAbility->Full_1000)
-         return RT_ERR_INPUT;
-
-     /*for PHY force mode setup*/
-     pAbility->AutoNegotiation = 0;
-
-     phyEnMsk0 = 0;
-     phyEnMsk4 = 0;
-     phyEnMsk9 = 0;
-
-     if (1 == pAbility->Half_10)
-     {
-         /*10BASE-TX half duplex capable in reg 4.5*/
-         phyEnMsk4 = phyEnMsk4 | (1 << 5);
-
-         /*Speed selection [1:0] */
-         /* 11=Reserved*/
-         /* 10= 1000Mpbs*/
-         /* 01= 100Mpbs*/
-         /* 00= 10Mpbs*/
-         phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-         phyEnMsk0 = phyEnMsk0 & (~(1 << 13));
-     }
-
-     if (1 == pAbility->Full_10)
-     {
-         /*10BASE-TX full duplex capable in reg 4.6*/
-         phyEnMsk4 = phyEnMsk4 | (1 << 6);
-         /*Speed selection [1:0] */
-         /* 11=Reserved*/
-         /* 10= 1000Mpbs*/
-         /* 01= 100Mpbs*/
-         /* 00= 10Mpbs*/
-         phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-         phyEnMsk0 = phyEnMsk0 & (~(1 << 13));
-
-         /*Full duplex mode in reg 0.8*/
-         phyEnMsk0 = phyEnMsk0 | (1 << 8);
-
-     }
-
-     if (1 == pAbility->Half_100)
-     {
-         /*100BASE-TX half duplex capable in reg 4.7*/
-         phyEnMsk4 = phyEnMsk4 | (1 << 7);
-         /*Speed selection [1:0] */
-         /* 11=Reserved*/
-         /* 10= 1000Mpbs*/
-         /* 01= 100Mpbs*/
-         /* 00= 10Mpbs*/
-         phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-         phyEnMsk0 = phyEnMsk0 | (1 << 13);
-     }
-
-
-     if (1 == pAbility->Full_100)
-     {
-         /*100BASE-TX full duplex capable in reg 4.8*/
-         phyEnMsk4 = phyEnMsk4 | (1 << 8);
-         /*Speed selection [1:0] */
-         /* 11=Reserved*/
-         /* 10= 1000Mpbs*/
-         /* 01= 100Mpbs*/
-         /* 00= 10Mpbs*/
-         phyEnMsk0 = phyEnMsk0 & (~(1 << 6));
-         phyEnMsk0 = phyEnMsk0 | (1 << 13);
-         /*Full duplex mode in reg 0.8*/
-         phyEnMsk0 = phyEnMsk0 | (1 << 8);
-     }
-
-     if (1 == pAbility->AsyFC)
-     {
-         /*Asymetric flow control in reg 4.11*/
-         phyEnMsk4 = phyEnMsk4 | (1 << 11);
-     }
-     if (1 == pAbility->FC)
-     {
-         /*Flow control in reg 4.10*/
-         phyEnMsk4 = phyEnMsk4 | ((1 << 10));
-     }
-
-     /*1000 BASE-T control register setting*/
-     if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_1000_BASET_CONTROL_REG, &phyData)) != RT_ERR_OK)
-         return retVal;
-
-     phyData = (phyData & (~0x0200)) | phyEnMsk9 ;
-
-     if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_1000_BASET_CONTROL_REG, phyData)) != RT_ERR_OK)
-         return retVal;
-
-     /*Auto-Negotiation control register setting*/
-     if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_AN_ADVERTISEMENT_REG, &phyData)) != RT_ERR_OK)
-         return retVal;
-
-     phyData = (phyData & (~0x0DE0)) | phyEnMsk4;
-     if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_AN_ADVERTISEMENT_REG, phyData)) != RT_ERR_OK)
-         return retVal;
-
-     /*Control register setting and power off/on*/
-     phyData = phyEnMsk0 & (~(1 << 12));
-     phyData |= (1 << 11);   /* power down PHY, bit 11 should be set to 1 */
-     if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, phyData)) != RT_ERR_OK)
-         return retVal;
-
-     phyData = phyData & (~(1 << 11));   /* power on PHY, bit 11 should be set to 0*/
-     if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, phyData)) != RT_ERR_OK)
-         return retVal;
-
-     return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyForceModeAbility_get
- * Description:
- *      Get PHY ability through PHY registers.
- * Input:
- *      port - Port id.
- * Output:
- *      pAbility - Ability structure
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      Get the capablity of specified PHY.
- */
-rtk_api_ret_t rtk_port_phyForceModeAbility_get(rtk_port_t port, rtk_port_phy_ability_t *pAbility)
-{
-    rtk_api_ret_t       retVal;
-    rtk_uint32          phyData0;
-    rtk_uint32          phyData4;
-    rtk_uint32          phyData9;
-    rtk_port_media_t    media_type;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-     RTK_CHK_PORT_IS_UTP(port);
-
-     if(NULL == pAbility)
-        return RT_ERR_NULL_POINTER;
-
-     if (rtk_switch_isComboPort(port) == RT_ERR_OK)
-     {
-         if ((retVal = rtk_port_phyComboPortMedia_get(port, &media_type)) != RT_ERR_OK)
-             return retVal;
-
-         if(media_type == PORT_MEDIA_FIBER)
-         {
-             return _rtk_port_FiberModeAbility_get(port, pAbility);
-         }
-     }
-
-    /*Control register setting and restart auto*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, &phyData0)) != RT_ERR_OK)
-        return retVal;
-
-    /*Auto-Negotiation control register setting*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_AN_ADVERTISEMENT_REG, &phyData4)) != RT_ERR_OK)
-        return retVal;
-
-    /*1000 BASE-T control register setting*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_1000_BASET_CONTROL_REG, &phyData9)) != RT_ERR_OK)
-        return retVal;
-
-    if (phyData9 & (1 << 9))
-        pAbility->Full_1000 = 1;
-    else
-        pAbility->Full_1000 = 0;
-
-    if (phyData4 & (1 << 11))
-        pAbility->AsyFC = 1;
-    else
-        pAbility->AsyFC = 0;
-
-    if (phyData4 & ((1 << 10)))
-        pAbility->FC = 1;
-    else
-        pAbility->FC = 0;
-
-
-    if (phyData4 & (1 << 8))
-        pAbility->Full_100 = 1;
-    else
-        pAbility->Full_100 = 0;
-
-    if (phyData4 & (1 << 7))
-        pAbility->Half_100 = 1;
-    else
-        pAbility->Half_100 = 0;
-
-    if (phyData4 & (1 << 6))
-        pAbility->Full_10 = 1;
-    else
-        pAbility->Full_10 = 0;
-
-    if (phyData4 & (1 << 5))
-        pAbility->Half_10 = 1;
-    else
-        pAbility->Half_10 = 0;
-
-
-    if (phyData0 & (1 << 12))
-        pAbility->AutoNegotiation = 1;
-    else
-        pAbility->AutoNegotiation = 0;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyStatus_get
- * Description:
- *      Get ethernet PHY linking status
- * Input:
- *      port - Port id.
- * Output:
- *      linkStatus  - PHY link status
- *      speed       - PHY link speed
- *      duplex      - PHY duplex mode
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      API will return auto negotiation status of phy.
- */
-rtk_api_ret_t rtk_port_phyStatus_get(rtk_port_t port, rtk_port_linkStatus_t *pLinkStatus, rtk_port_speed_t *pSpeed, rtk_port_duplex_t *pDuplex)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 phyData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if( (NULL == pLinkStatus) || (NULL == pSpeed) || (NULL == pDuplex) )
-        return RT_ERR_NULL_POINTER;
-
-    /*Get PHY resolved register*/
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_RESOLVED_REG, &phyData)) != RT_ERR_OK)
-        return retVal;
-
-    /*check link status*/
-    if (phyData & (1<<2))
-    {
-        *pLinkStatus = 1;
-
-        /*check link speed*/
-        *pSpeed = (phyData&0x0030) >> 4;
-
-        /*check link duplex*/
-        *pDuplex = (phyData&0x0008) >> 3;
-    }
-    else
-    {
-        *pLinkStatus = 0;
-        *pSpeed = 0;
-        *pDuplex = 0;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_macForceLink_set
- * Description:
- *      Set port force linking configuration.
- * Input:
- *      port            - port id.
- *      pPortability    - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can set Port/MAC force mode properties.
- */
-rtk_api_ret_t rtk_port_macForceLink_set(rtk_port_t port, rtk_port_mac_ability_t *pPortability)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_port_ability_t ability;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if(NULL == pPortability)
-        return RT_ERR_NULL_POINTER;
-
-    if (pPortability->forcemode >1|| pPortability->speed > 2 || pPortability->duplex > 1 ||
-       pPortability->link > 1 || pPortability->nway > 1 || pPortability->txpause > 1 || pPortability->rxpause > 1)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_getAsicPortForceLink(rtk_switch_port_L2P_get(port), &ability)) != RT_ERR_OK)
-        return retVal;
-
-    ability.forcemode = pPortability->forcemode;
-    ability.speed     = pPortability->speed;
-    ability.duplex    = pPortability->duplex;
-    ability.link      = pPortability->link;
-    ability.nway      = pPortability->nway;
-    ability.txpause   = pPortability->txpause;
-    ability.rxpause   = pPortability->rxpause;
-
-    if ((retVal = rtl8367c_setAsicPortForceLink(rtk_switch_port_L2P_get(port), &ability)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_macForceLink_get
- * Description:
- *      Get port force linking configuration.
- * Input:
- *      port - Port id.
- * Output:
- *      pPortability - port ability configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get Port/MAC force mode properties.
- */
-rtk_api_ret_t rtk_port_macForceLink_get(rtk_port_t port, rtk_port_mac_ability_t *pPortability)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_port_ability_t ability;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if(NULL == pPortability)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortForceLink(rtk_switch_port_L2P_get(port), &ability)) != RT_ERR_OK)
-        return retVal;
-
-    pPortability->forcemode = ability.forcemode;
-    pPortability->speed     = ability.speed;
-    pPortability->duplex    = ability.duplex;
-    pPortability->link      = ability.link;
-    pPortability->nway      = ability.nway;
-    pPortability->txpause   = ability.txpause;
-    pPortability->rxpause   = ability.rxpause;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_macForceLinkExt_set
- * Description:
- *      Set external interface force linking configuration.
- * Input:
- *      port            - external port ID
- *      mode            - external interface mode
- *      pPortability    - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set external interface force mode properties.
- *      The external interface can be set to:
- *      - MODE_EXT_DISABLE,
- *      - MODE_EXT_RGMII,
- *      - MODE_EXT_MII_MAC,
- *      - MODE_EXT_MII_PHY,
- *      - MODE_EXT_TMII_MAC,
- *      - MODE_EXT_TMII_PHY,
- *      - MODE_EXT_GMII,
- *      - MODE_EXT_RMII_MAC,
- *      - MODE_EXT_RMII_PHY,
- *      - MODE_EXT_SGMII,
- *      - MODE_EXT_HSGMII,
- *      - MODE_EXT_1000X_100FX,
- *      - MODE_EXT_1000X,
- *      - MODE_EXT_100FX,
- */
-rtk_api_ret_t rtk_port_macForceLinkExt_set(rtk_port_t port, rtk_mode_ext_t mode, rtk_port_mac_ability_t *pPortability)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_port_ability_t ability;
-    rtk_uint32 ext_id;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_EXT(port);
-
-    if(NULL == pPortability)
-        return RT_ERR_NULL_POINTER;
-
-    if (mode >=MODE_EXT_END)
-        return RT_ERR_INPUT;
-
-    if(mode == MODE_EXT_HSGMII)
-    {
-        if (pPortability->forcemode > 1 || pPortability->speed != PORT_SPEED_2500M || pPortability->duplex != PORT_FULL_DUPLEX ||
-           pPortability->link >= PORT_LINKSTATUS_END || pPortability->nway > 1 || pPortability->txpause > 1 || pPortability->rxpause > 1)
-            return RT_ERR_INPUT;
-
-        if(rtk_switch_isHsgPort(port) != RT_ERR_OK)
-            return RT_ERR_PORT_ID;
-    }
-    else
-    {
-        if (pPortability->forcemode > 1 || pPortability->speed > PORT_SPEED_1000M || pPortability->duplex >= PORT_DUPLEX_END ||
-           pPortability->link >= PORT_LINKSTATUS_END || pPortability->nway > 1 || pPortability->txpause > 1 || pPortability->rxpause > 1)
-            return RT_ERR_INPUT;
-    }
-
-    ext_id = port - 15;
-
-    if(mode == MODE_EXT_DISABLE)
-    {
-        memset(&ability, 0x00, sizeof(rtl8367c_port_ability_t));
-        if ((retVal = rtl8367c_setAsicPortForceLinkExt(ext_id, &ability)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicPortExtMode(ext_id, mode)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        if ((retVal = rtl8367c_setAsicPortExtMode(ext_id, mode)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_getAsicPortForceLinkExt(ext_id, &ability)) != RT_ERR_OK)
-            return retVal;
-
-        ability.forcemode = pPortability->forcemode;
-        ability.speed     = (mode == MODE_EXT_HSGMII) ? PORT_SPEED_1000M : pPortability->speed;
-        ability.duplex    = pPortability->duplex;
-        ability.link      = pPortability->link;
-        ability.nway      = pPortability->nway;
-        ability.txpause   = pPortability->txpause;
-        ability.rxpause   = pPortability->rxpause;
-
-        if ((retVal = rtl8367c_setAsicPortForceLinkExt(ext_id, &ability)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_macForceLinkExt_get
- * Description:
- *      Set external interface force linking configuration.
- * Input:
- *      port            - external port ID
- * Output:
- *      pMode           - external interface mode
- *      pPortability    - port ability configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get external interface force mode properties.
- */
-rtk_api_ret_t rtk_port_macForceLinkExt_get(rtk_port_t port, rtk_mode_ext_t *pMode, rtk_port_mac_ability_t *pPortability)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_port_ability_t ability;
-    rtk_uint32 ext_id;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_EXT(port);
-
-    if(NULL == pMode)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pPortability)
-        return RT_ERR_NULL_POINTER;
-
-    ext_id = port - 15;
-
-    if ((retVal = rtl8367c_getAsicPortExtMode(ext_id, (rtk_uint32 *)pMode)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPortForceLinkExt(ext_id, &ability)) != RT_ERR_OK)
-        return retVal;
-
-    pPortability->forcemode = ability.forcemode;
-    pPortability->speed     = (*pMode == MODE_EXT_HSGMII) ? PORT_SPEED_2500M : ability.speed;
-    pPortability->duplex    = ability.duplex;
-    pPortability->link      = ability.link;
-    pPortability->nway      = ability.nway;
-    pPortability->txpause   = ability.txpause;
-    pPortability->rxpause   = ability.rxpause;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_port_macStatus_get
- * Description:
- *      Get port link status.
- * Input:
- *      port - Port id.
- * Output:
- *      pPortstatus - port ability configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get Port/PHY properties.
- */
-rtk_api_ret_t rtk_port_macStatus_get(rtk_port_t port, rtk_port_mac_ability_t *pPortstatus)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_port_status_t status;
-    rtk_uint32 hsgsel;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pPortstatus)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortStatus(rtk_switch_port_L2P_get(port), &status)) != RT_ERR_OK)
-        return retVal;
-
-
-    pPortstatus->duplex    = status.duplex;
-    pPortstatus->link      = status.link;
-    pPortstatus->nway      = status.nway;
-    pPortstatus->txpause   = status.txpause;
-    pPortstatus->rxpause   = status.rxpause;
-
-    if( (retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_HSGMII_OFFSET, &hsgsel)) != RT_ERR_OK)
-            return retVal;
-
-    if( (rtk_switch_isHsgPort(port) == RT_ERR_OK) && (hsgsel == 1) )
-        pPortstatus->speed = PORT_SPEED_2500M;
-    else
-        pPortstatus->speed = status.speed;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_macLocalLoopbackEnable_set
- * Description:
- *      Set Port Local Loopback. (Redirect TX to RX.)
- * Input:
- *      port    - Port id.
- *      enable  - Loopback state, 0:disable, 1:enable
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can enable/disable Local loopback in MAC.
- *      For UTP port, This API will also enable the digital
- *      loopback bit in PHY register for sync of speed between
- *      PHY and MAC. For EXT port, users need to force the
- *      link state by themself.
- */
-rtk_api_ret_t rtk_port_macLocalLoopbackEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      data;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicPortLoopback(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-        return retVal;
-
-    if(rtk_switch_isUtpPort(port) == RT_ERR_OK)
-    {
-        if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, &data)) != RT_ERR_OK)
-            return retVal;
-
-        if(enable == ENABLED)
-            data |= (0x0001 << 14);
-        else
-            data &= ~(0x0001 << 14);
-
-        if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), PHY_CONTROL_REG, data)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_macLocalLoopbackEnable_get
- * Description:
- *      Get Port Local Loopback. (Redirect TX to RX.)
- * Input:
- *      port    - Port id.
- * Output:
- *      pEnable  - Loopback state, 0:disable, 1:enable
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_port_macLocalLoopbackEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortLoopback(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyReg_set
- * Description:
- *      Set PHY register data of the specific port.
- * Input:
- *      port    - port id.
- *      reg     - Register id
- *      regData - Register data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      This API can set PHY register data of the specific port.
- */
-rtk_api_ret_t rtk_port_phyReg_set(rtk_port_t port, rtk_port_phy_reg_t reg, rtk_port_phy_data_t regData)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), reg, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyReg_get
- * Description:
- *      Get PHY register data of the specific port.
- * Input:
- *      port    - Port id.
- *      reg     - Register id
- * Output:
- *      pData   - Register data
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_PHY_REG_ID       - Invalid PHY address
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      This API can get PHY register data of the specific port.
- */
-rtk_api_ret_t rtk_port_phyReg_get(rtk_port_t port, rtk_port_phy_reg_t reg, rtk_port_phy_data_t *pData)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), reg, pData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_backpressureEnable_set
- * Description:
- *      Set the half duplex backpressure enable status of the specific port.
- * Input:
- *      port    - port id.
- *      enable  - Back pressure status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can set the half duplex backpressure enable status of the specific port.
- *      The half duplex backpressure enable status of the port is as following:
- *      - DISABLE(Defer)
- *      - ENABLE (Backpressure)
- */
-rtk_api_ret_t rtk_port_backpressureEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicPortJamMode(!enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_backpressureEnable_get
- * Description:
- *      Get the half duplex backpressure enable status of the specific port.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Back pressure status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get the half duplex backpressure enable status of the specific port.
- *      The half duplex backpressure enable status of the port is as following:
- *      - DISABLE(Defer)
- *      - ENABLE (Backpressure)
- */
-rtk_api_ret_t rtk_port_backpressureEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortJamMode(&regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pEnable = !regData;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_adminEnable_set
- * Description:
- *      Set port admin configuration of the specific port.
- * Input:
- *      port    - port id.
- *      enable  - Back pressure status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can set port admin configuration of the specific port.
- *      The port admin configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-rtk_api_ret_t rtk_port_adminEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32      data;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtk_port_phyReg_get(port, PHY_CONTROL_REG, &data)) != RT_ERR_OK)
-        return retVal;
-
-    if (ENABLED == enable)
-    {
-        data &= 0xF7FF;
-        data |= 0x0200;
-    }
-    else if (DISABLED == enable)
-    {
-        data |= 0x0800;
-    }
-
-    if ((retVal = rtk_port_phyReg_set(port, PHY_CONTROL_REG, data)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_adminEnable_get
- * Description:
- *      Get port admin configurationof the specific port.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Back pressure status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API can get port admin configuration of the specific port.
- *      The port admin configuration of the port is as following:
- *      - DISABLE
- *      - ENABLE
- */
-rtk_api_ret_t rtk_port_adminEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32      data;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtk_port_phyReg_get(port, PHY_CONTROL_REG, &data)) != RT_ERR_OK)
-        return retVal;
-
-    if ( (data & 0x0800) == 0x0800)
-    {
-        *pEnable = DISABLED;
-    }
-    else
-    {
-        *pEnable = ENABLED;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_isolation_set
- * Description:
- *      Set permitted port isolation portmask
- * Input:
- *      port         - port id.
- *      pPortmask    - Permit port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      This API set the port mask that a port can trasmit packet to of each port
- *      A port can only transmit packet to ports included in permitted portmask
- */
-rtk_api_ret_t rtk_port_isolation_set(rtk_port_t port, rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    /* check port mask */
-    RTK_CHK_PORTMASK_VALID(pPortmask);
-
-    if ((retVal = rtk_switch_portmask_L2P_get(pPortmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPortIsolationPermittedPortmask(rtk_switch_port_L2P_get(port), pmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_isolation_get
- * Description:
- *      Get permitted port isolation portmask
- * Input:
- *      port - Port id.
- * Output:
- *      pPortmask - Permit port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API get the port mask that a port can trasmit packet to of each port
- *      A port can only transmit packet to ports included in permitted portmask
- */
-rtk_api_ret_t rtk_port_isolation_get(rtk_port_t port, rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortIsolationPermittedPortmask(rtk_switch_port_L2P_get(port), &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_rgmiiDelayExt_set
- * Description:
- *      Set RGMII interface delay value for TX and RX.
- * Input:
- *      txDelay - TX delay value, 1 for delay 2ns and 0 for no-delay
- *      rxDelay - RX delay value, 0~7 for delay setup.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set external interface 2 RGMII delay.
- *      In TX delay, there are 2 selection: no-delay and 2ns delay.
- *      In RX dekay, there are 8 steps for delay tunning. 0 for no-delay, and 7 for maximum delay.
- */
-rtk_api_ret_t rtk_port_rgmiiDelayExt_set(rtk_port_t port, rtk_data_t txDelay, rtk_data_t rxDelay)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regAddr, regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_EXT(port);
-
-    if ((txDelay > 1) || (rxDelay > 7))
-        return RT_ERR_INPUT;
-
-    if(port == EXT_PORT0)
-        regAddr = RTL8367C_REG_EXT1_RGMXF;
-    else if(port == EXT_PORT1)
-        regAddr = RTL8367C_REG_EXT2_RGMXF;
-    else
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_getAsicReg(regAddr, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    regData = (regData & 0xFFF0) | ((txDelay << 3) & 0x0008) | (rxDelay & 0x0007);
-
-    if ((retVal = rtl8367c_setAsicReg(regAddr, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_rgmiiDelayExt_get
- * Description:
- *      Get RGMII interface delay value for TX and RX.
- * Input:
- *      None
- * Output:
- *      pTxDelay - TX delay value
- *      pRxDelay - RX delay value
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can set external interface 2 RGMII delay.
- *      In TX delay, there are 2 selection: no-delay and 2ns delay.
- *      In RX dekay, there are 8 steps for delay tunning. 0 for n0-delay, and 7 for maximum delay.
- */
-rtk_api_ret_t rtk_port_rgmiiDelayExt_get(rtk_port_t port, rtk_data_t *pTxDelay, rtk_data_t *pRxDelay)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regAddr, regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_EXT(port);
-
-    if( (NULL == pTxDelay) || (NULL == pRxDelay) )
-        return RT_ERR_NULL_POINTER;
-
-    if(port == EXT_PORT0)
-        regAddr = RTL8367C_REG_EXT1_RGMXF;
-    else if(port == EXT_PORT1)
-        regAddr = RTL8367C_REG_EXT2_RGMXF;
-    else
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_getAsicReg(regAddr, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pTxDelay = (regData & 0x0008) >> 3;
-    *pRxDelay = regData & 0x0007;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyEnableAll_set
- * Description:
- *      Set all PHY enable status.
- * Input:
- *      enable - PHY Enable State.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      This API can set all PHY status.
- *      The configuration of all PHY is as following:
- *      - DISABLE
- *      - ENABLE
- */
-rtk_api_ret_t rtk_port_phyEnableAll_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 data;
-    rtk_uint32 port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortEnableAll(enable)) != RT_ERR_OK)
-        return retVal;
-
-    RTK_SCAN_ALL_LOG_PORT(port)
-    {
-        if(rtk_switch_isUtpPort(port) == RT_ERR_OK)
-        {
-            if ((retVal = rtk_port_phyReg_get(port, PHY_CONTROL_REG, &data)) != RT_ERR_OK)
-                return retVal;
-
-            if (ENABLED == enable)
-            {
-                data &= 0xF7FF;
-                data |= 0x0200;
-            }
-            else
-            {
-                data |= 0x0800;
-            }
-
-            if ((retVal = rtk_port_phyReg_set(port, PHY_CONTROL_REG, data)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_port_phyEnableAll_get
- * Description:
- *      Get all PHY enable status.
- * Input:
- *      None
- * Output:
- *      pEnable - PHY Enable State.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      This API can set all PHY status.
- *      The configuration of all PHY is as following:
- *      - DISABLE
- *      - ENABLE
- */
-rtk_api_ret_t rtk_port_phyEnableAll_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortEnableAll(pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_efid_set
- * Description:
- *      Set port-based enhanced filtering database
- * Input:
- *      port - Port id.
- *      efid - Specified enhanced filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_L2_FID - Invalid fid.
- *      RT_ERR_INPUT - Invalid input parameter.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can set port-based enhanced filtering database.
- */
-rtk_api_ret_t rtk_port_efid_set(rtk_port_t port, rtk_data_t efid)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    /* efid must be 0~7 */
-    if (efid > RTK_EFID_MAX)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicPortIsolationEfid(rtk_switch_port_L2P_get(port), efid))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_efid_get
- * Description:
- *      Get port-based enhanced filtering database
- * Input:
- *      port - Port id.
- * Output:
- *      pEfid - Specified enhanced filtering database.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can get port-based enhanced filtering database status.
- */
-rtk_api_ret_t rtk_port_efid_get(rtk_port_t port, rtk_data_t *pEfid)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pEfid)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortIsolationEfid(rtk_switch_port_L2P_get(port), pEfid))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyComboPortMedia_set
- * Description:
- *      Set Combo port media type
- * Input:
- *      port    - Port id.
- *      media   - Media (COPPER or FIBER)
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_PORT_ID          - Invalid port ID.
- * Note:
- *      The API can Set Combo port media type.
- */
-rtk_api_ret_t rtk_port_phyComboPortMedia_set(rtk_port_t port, rtk_port_media_t media)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint32 idx;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    /* Check Combo Port ID */
-    RTK_CHK_PORT_IS_COMBO(port);
-
-    if (media >= PORT_MEDIA_END)
-        return RT_ERR_INPUT;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    if(regData != 0x6367)
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    if(media == PORT_MEDIA_FIBER)
-    {
-        /* software init */
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_CHIP_RESET, RTL8367C_DW8051_RST_OFFSET, 1)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MISCELLANEOUS_CONFIGURE0, RTL8367C_DW8051_EN_OFFSET, 1)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_ACS_IROM_ENABLE_OFFSET, 1)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_IROM_MSB_OFFSET, 0)) != RT_ERR_OK)
-            return retVal;
-
-        for(idx = 0; idx < FIBER_INIT_SIZE; idx++)
-        {
-            if ((retVal = rtl8367c_setAsicReg(0xE000 + idx, (rtk_uint32)Fiber[idx])) != RT_ERR_OK)
-                return retVal;
-        }
-
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_IROM_MSB_OFFSET, 0)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_ACS_IROM_ENABLE_OFFSET, 0)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_CHIP_RESET, RTL8367C_DW8051_RST_OFFSET, 0)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_UTP_FIB_DET, RTL8367C_UTP_FIRST_OFFSET, 1))!=RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_DW8051_READY_OFFSET, 0)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_phyComboPortMedia_get
- * Description:
- *      Get Combo port media type
- * Input:
- *      port    - Port id.
- * Output:
- *      pMedia  - Media (COPPER or FIBER)
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_PORT_ID          - Invalid port ID.
- * Note:
- *      The API can Set Combo port media type.
- */
-rtk_api_ret_t rtk_port_phyComboPortMedia_get(rtk_port_t port, rtk_port_media_t *pMedia)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-    rtk_uint32      data;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    /* Check Combo Port ID */
-    RTK_CHK_PORT_IS_COMBO(port);
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    if(regData != 0x6367)
-    {
-        *pMedia = PORT_MEDIA_COPPER;
-    }
-    else
-    {
-        if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_UTP_FIB_DET, RTL8367C_UTP_FIRST_OFFSET, &data))!=RT_ERR_OK)
-                return retVal;
-
-        if(data == 1)
-            *pMedia = PORT_MEDIA_COPPER;
-        else
-            *pMedia = PORT_MEDIA_FIBER;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_rtctEnable_set
- * Description:
- *      Enable RTCT test
- * Input:
- *      pPortmask    - Port mask of RTCT enabled port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_MASK        - Invalid port mask.
- * Note:
- *      The API can enable RTCT Test
- */
-rtk_api_ret_t rtk_port_rtctEnable_set(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Mask Valid */
-    RTK_CHK_PORTMASK_VALID_ONLY_UTP(pPortmask);
-
-    if ((retVal = rtl8367c_setAsicPortRTCTEnable(pPortmask->bits[0]))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_rtctDisable_set
- * Description:
- *      Disable RTCT test
- * Input:
- *      pPortmask    - Port mask of RTCT disabled port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_MASK        - Invalid port mask.
- * Note:
- *      The API can disable RTCT Test
- */
-rtk_api_ret_t rtk_port_rtctDisable_set(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Mask Valid */
-    RTK_CHK_PORTMASK_VALID_ONLY_UTP(pPortmask);
-
-    if ((retVal = rtl8367c_setAsicPortRTCTDisable(pPortmask->bits[0]))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_port_rtctResult_get
- * Description:
- *      Get the result of RTCT test
- * Input:
- *      port        - Port ID
- * Output:
- *      pRtctResult - The result of RTCT result
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- *      RT_ERR_PHY_RTCT_NOT_FINISH  - Testing does not finish.
- * Note:
- *      The API can get RTCT test result.
- *      RTCT test may takes 4.8 seconds to finish its test at most.
- *      Thus, if this API return RT_ERR_PHY_RTCT_NOT_FINISH or
- *      other error code, the result can not be referenced and
- *      user should call this API again until this API returns
- *      a RT_ERR_OK.
- *      The result is stored at pRtctResult->ge_result
- *      pRtctResult->linkType is unused.
- *      The unit of channel length is 2.5cm. Ex. 300 means 300 * 2.5 = 750cm = 7.5M
- */
-rtk_api_ret_t rtk_port_rtctResult_get(rtk_port_t port, rtk_rtctResult_t *pRtctResult)
-{
-    rtk_api_ret_t               retVal;
-    rtl8367c_port_rtct_result_t result;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_IS_UTP(port);
-
-    memset(pRtctResult, 0x00, sizeof(rtk_rtctResult_t));
-    if ((retVal = rtl8367c_getAsicPortRTCTResult(port, &result))!=RT_ERR_OK)
-        return retVal;
-
-    pRtctResult->result.ge_result.channelALen = result.channelALen;
-    pRtctResult->result.ge_result.channelBLen = result.channelBLen;
-    pRtctResult->result.ge_result.channelCLen = result.channelCLen;
-    pRtctResult->result.ge_result.channelDLen = result.channelDLen;
-
-    pRtctResult->result.ge_result.channelALinedriver = result.channelALinedriver;
-    pRtctResult->result.ge_result.channelBLinedriver = result.channelBLinedriver;
-    pRtctResult->result.ge_result.channelCLinedriver = result.channelCLinedriver;
-    pRtctResult->result.ge_result.channelDLinedriver = result.channelDLinedriver;
-
-    pRtctResult->result.ge_result.channelAMismatch = result.channelAMismatch;
-    pRtctResult->result.ge_result.channelBMismatch = result.channelBMismatch;
-    pRtctResult->result.ge_result.channelCMismatch = result.channelCMismatch;
-    pRtctResult->result.ge_result.channelDMismatch = result.channelDMismatch;
-
-    pRtctResult->result.ge_result.channelAOpen = result.channelAOpen;
-    pRtctResult->result.ge_result.channelBOpen = result.channelBOpen;
-    pRtctResult->result.ge_result.channelCOpen = result.channelCOpen;
-    pRtctResult->result.ge_result.channelDOpen = result.channelDOpen;
-
-    pRtctResult->result.ge_result.channelAShort = result.channelAShort;
-    pRtctResult->result.ge_result.channelBShort = result.channelBShort;
-    pRtctResult->result.ge_result.channelCShort = result.channelCShort;
-    pRtctResult->result.ge_result.channelDShort = result.channelDShort;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_port_sds_reset
- * Description:
- *      Reset Serdes
- * Input:
- *      port        - Port ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API can reset Serdes
- */
-rtk_api_ret_t rtk_port_sds_reset(rtk_port_t port)
-{
-    rtk_uint32 ext_id;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    if(rtk_switch_isSgmiiPort(port) != RT_ERR_OK)
-        return RT_ERR_PORT_ID;
-
-    ext_id = port - 15;
-    return rtl8367c_sdsReset(ext_id);
-}
-
-/* Function Name:
- *      rtk_port_sgmiiLinkStatus_get
- * Description:
- *      Get SGMII status
- * Input:
- *      port        - Port ID
- * Output:
- *      pSignalDetect   - Signal detect
- *      pSync           - Sync
- *      pLink           - Link
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API can reset Serdes
- */
-rtk_api_ret_t rtk_port_sgmiiLinkStatus_get(rtk_port_t port, rtk_data_t *pSignalDetect, rtk_data_t *pSync, rtk_port_linkStatus_t *pLink)
-{
-    rtk_uint32 ext_id;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    if(rtk_switch_isSgmiiPort(port) != RT_ERR_OK)
-        return RT_ERR_PORT_ID;
-
-    if(NULL == pSignalDetect)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pSync)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pLink)
-        return RT_ERR_NULL_POINTER;
-
-    ext_id = port - 15;
-    return rtl8367c_getSdsLinkStatus(ext_id, (rtk_uint32 *)pSignalDetect, (rtk_uint32 *)pSync, (rtk_uint32 *)pLink);
-}
-
-/* Function Name:
- *      rtk_port_sgmiiNway_set
- * Description:
- *      Configure SGMII/HSGMII port Nway state
- * Input:
- *      port        - Port ID
- *      state       - Nway state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API configure SGMII/HSGMII port Nway state
- */
-rtk_api_ret_t rtk_port_sgmiiNway_set(rtk_port_t port, rtk_enable_t state)
-{
-    rtk_uint32 ext_id;
-
-     /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    if(rtk_switch_isSgmiiPort(port) != RT_ERR_OK)
-        return RT_ERR_PORT_ID;
-
-    if(state >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    ext_id = port - 15;
-    return rtl8367c_setSgmiiNway(ext_id, (rtk_uint32)state);
-}
-
-/* Function Name:
- *      rtk_port_sgmiiNway_get
- * Description:
- *      Get SGMII/HSGMII port Nway state
- * Input:
- *      port        - Port ID
- * Output:
- *      pState      - Nway state
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port ID.
- * Note:
- *      The API can get SGMII/HSGMII port Nway state
- */
-rtk_api_ret_t rtk_port_sgmiiNway_get(rtk_port_t port, rtk_enable_t *pState)
-{
-    rtk_uint32 ext_id;
-
-     /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    if(rtk_switch_isSgmiiPort(port) != RT_ERR_OK)
-        return RT_ERR_PORT_ID;
-
-    if(NULL == pState)
-        return RT_ERR_NULL_POINTER;
-
-    ext_id = port - 15;
-    return rtl8367c_getSgmiiNway(ext_id, (rtk_uint32 *)pState);
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/ptp.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/ptp.c
deleted file mode 100644
index 40962a0e69..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/ptp.c
+++ /dev/null
@@ -1,759 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 39583 $
- * $Date: 2013-05-20 16:59:23 +0800 (星期一, 20 五月 2013) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in time module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <ptp.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_eav.h>
-
-/* Function Name:
- *      rtk_ptp_init
- * Description:
- *      PTP function initialization.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API is used to initialize PTP status.
- */
-rtk_api_ret_t rtk_ptp_init(void)
-{
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_mac_set
- * Description:
- *      Configure PTP mac address.
- * Input:
- *      mac - mac address to parser PTP packets.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_mac_set(rtk_mac_t mac)
-{
-    rtk_api_ret_t retVal;
-    ether_addr_t sw_mac;
-
-    memcpy(sw_mac.octet, mac.octet, ETHER_ADDR_LEN);
-
-    if((retVal=rtl8367c_setAsicEavMacAddress(sw_mac))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_mac_get
- * Description:
- *      Get PTP mac address.
- * Input:
- *      None
- * Output:
- *      pMac - mac address to parser PTP packets.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_mac_get(rtk_mac_t *pMac)
-{
-    rtk_api_ret_t retVal;
-    ether_addr_t sw_mac;
-
-    if((retVal=rtl8367c_getAsicEavMacAddress(&sw_mac))!=RT_ERR_OK)
-        return retVal;
-
-    memcpy(pMac->octet, sw_mac.octet, ETHER_ADDR_LEN);
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_tpid_set
- * Description:
- *      Configure PTP accepted outer & inner tag TPID.
- * Input:
- *      outerId - Ether type of S-tag frame parsing in PTP ports.
- *      innerId - Ether type of C-tag frame parsing in PTP ports.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_tpid_set(rtk_ptp_tpid_t outerId, rtk_ptp_tpid_t innerId)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((outerId>RTK_MAX_NUM_OF_TPID) ||(innerId>RTK_MAX_NUM_OF_TPID))
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicEavTpid(outerId, innerId)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_tpid_get
- * Description:
- *      Get PTP accepted outer & inner tag TPID.
- * Input:
- *      None
- * Output:
- *      pOuterId - Ether type of S-tag frame parsing in PTP ports.
- *      pInnerId - Ether type of C-tag frame parsing in PTP ports.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_tpid_get(rtk_ptp_tpid_t *pOuterId, rtk_ptp_tpid_t *pInnerId)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicEavTpid(pOuterId, pInnerId)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_refTime_set
- * Description:
- *      Set the reference time of the specified device.
- * Input:
- *      timeStamp - reference timestamp value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT    - invalid input parameter
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_refTime_set(rtk_ptp_timeStamp_t timeStamp)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (timeStamp.nsec > RTK_MAX_NUM_OF_NANO_SECOND)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicEavSysTime(timeStamp.sec, timeStamp.nsec))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_refTime_get
- * Description:
- *      Get the reference time of the specified device.
- * Input:
- * Output:
- *      pTimeStamp - pointer buffer of the reference time
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_NOT_INIT     - The module is not initial
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_refTime_get(rtk_ptp_timeStamp_t *pTimeStamp)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicEavSysTime(&pTimeStamp->sec, &pTimeStamp->nsec))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_refTimeAdjust_set
- * Description:
- *      Adjust the reference time.
- * Input:
- *      unit      - unit id
- *      sign      - significant
- *      timeStamp - reference timestamp value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID  - invalid unit id
- *      RT_ERR_NOT_INIT - The module is not initial
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      sign=0 for positive adjustment, sign=1 for negative adjustment.
- */
-rtk_api_ret_t rtk_ptp_refTimeAdjust_set(rtk_ptp_sys_adjust_t sign, rtk_ptp_timeStamp_t timeStamp)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (timeStamp.nsec > RTK_MAX_NUM_OF_NANO_SECOND)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicEavSysTimeAdjust(sign, timeStamp.sec, timeStamp.nsec))!=RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_refTimeEnable_set
- * Description:
- *      Set the enable state of reference time of the specified device.
- * Input:
- *      enable - status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_refTimeEnable_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicEavSysTimeCtrl(enable))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_refTimeEnable_get
- * Description:
- *      Get the enable state of reference time of the specified device.
- * Input:
- * Output:
- *      pEnable - status
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_NOT_INIT     - The module is not initial
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_refTimeEnable_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicEavSysTimeCtrl(pEnable))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_portEnable_set
- * Description:
- *      Set PTP status of the specified port.
- * Input:
- *      port   - port id
- *      enable - status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT     - invalid port id
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_portEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port is PTP port */
-    RTK_CHK_PORT_IS_PTP(port);
-
-    if (enable>=RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicEavPortEnable(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_portEnable_get
- * Description:
- *      Get PTP status of the specified port.
- * Input:
- *      port    - port id
- * Output:
- *      pEnable - status
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT         - invalid port id
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_portEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port is PTP port */
-    RTK_CHK_PORT_IS_PTP(port);
-
-    if ((retVal = rtl8367c_getAsicEavPortEnable(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_ptp_portTimestamp_get
- * Description:
- *      Get PTP timstamp according to the PTP identifier on the dedicated port from the specified device.
- * Input:
- *      unit       - unit id
- *      port       - port id
- *      type       - PTP message type
- * Output:
- *      pInfo      - pointer buffer of sequence ID and timestamp
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID      - invalid port id
- *      RT_ERR_INPUT        - invalid input parameter
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Applicable:
- *      8390, 8380
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_portTimestamp_get( rtk_port_t port, rtk_ptp_msgType_t type, rtk_ptp_info_t *pInfo)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_ptp_time_stamp_t time;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port is PTP port */
-    RTK_CHK_PORT_IS_PTP(port);
-
-    if ((retVal = rtl8367c_getAsicEavPortTimeStamp(rtk_switch_port_L2P_get(port), type, &time)) != RT_ERR_OK)
-        return retVal;
-
-    pInfo->sequenceId = time.sequence_id;
-    pInfo->timeStamp.sec = time.second;
-    pInfo->timeStamp.nsec = time.nano_second;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_intControl_set
- * Description:
- *      Set PTP interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- *      enable - Interrupt status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The API can set PTP interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *          PTP_INT_TYPE_TX_SYNC = 0,
- *          PTP_INT_TYPE_TX_DELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_RESP,
- *          PTP_INT_TYPE_RX_SYNC,
- *          PTP_INT_TYPE_RX_DELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_RESP,
- *          PTP_INT_TYPE_ALL,
- */
-rtk_api_ret_t rtk_ptp_intControl_set(rtk_ptp_intType_t type, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 mask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type>=PTP_INT_TYPE_END)
-        return RT_ERR_INPUT;
-
-    if (PTP_INT_TYPE_ALL!=type)
-    {
-        if ((retVal = rtl8367c_getAsicEavInterruptMask(&mask)) != RT_ERR_OK)
-            return retVal;
-
-        if (ENABLED == enable)
-            mask = mask | (1<<type);
-        else if (DISABLED == enable)
-            mask = mask & ~(1<<type);
-        else
-            return RT_ERR_INPUT;
-
-        if ((retVal = rtl8367c_setAsicEavInterruptMask(mask)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        if (ENABLED == enable)
-            mask = RTK_PTP_INTR_MASK;
-        else if (DISABLED == enable)
-            mask = 0;
-        else
-            return RT_ERR_INPUT;
-
-        if ((retVal = rtl8367c_setAsicEavInterruptMask(mask)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_intControl_get
- * Description:
- *      Get PTP interrupt trigger status configuration.
- * Input:
- *      type - Interrupt type.
- * Output:
- *      pEnable - Interrupt status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt status configuration.
- *      The interrupt trigger status is shown in the following:
- *          PTP_INT_TYPE_TX_SYNC = 0,
- *          PTP_INT_TYPE_TX_DELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_REQ,
- *          PTP_INT_TYPE_TX_PDELAY_RESP,
- *          PTP_INT_TYPE_RX_SYNC,
- *          PTP_INT_TYPE_RX_DELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_REQ,
- *          PTP_INT_TYPE_RX_PDELAY_RESP,
- */
-rtk_api_ret_t rtk_ptp_intControl_get(rtk_ptp_intType_t type, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 mask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type>=PTP_INT_TYPE_ALL)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_getAsicEavInterruptMask(&mask)) != RT_ERR_OK)
-        return retVal;
-
-    if (0 == (mask&(1<<type)))
-        *pEnable=DISABLED;
-    else
-        *pEnable=ENABLED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_intStatus_get
- * Description:
- *      Get PTP port interrupt trigger status.
- * Input:
- *      port           - physical port
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - PORT 0  INT    (value[0] (Bit0))
- *      - PORT 1  INT    (value[0] (Bit1))
- *      - PORT 2  INT    (value[0] (Bit2))
- *      - PORT 3  INT    (value[0] (Bit3))
- *      - PORT 4  INT   (value[0] (Bit4))
-
- *
- */
-rtk_api_ret_t rtk_ptp_intStatus_get(rtk_ptp_intStatus_t *pStatusMask)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pStatusMask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicEavInterruptStatus(pStatusMask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
-/* Function Name:
- *      rtk_ptp_portIntStatus_set
- * Description:
- *      Set PTP port interrupt trigger status to clean.
- * Input:
- *      port           - physical port
- *      statusMask - Interrupt status bit mask.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- * Note:
- *      The API can clean interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - PTP_INT_TYPE_TX_SYNC              (value[0] (Bit0))
- *      - PTP_INT_TYPE_TX_DELAY_REQ      (value[0] (Bit1))
- *      - PTP_INT_TYPE_TX_PDELAY_REQ    (value[0] (Bit2))
- *      - PTP_INT_TYPE_TX_PDELAY_RESP   (value[0] (Bit3))
- *      - PTP_INT_TYPE_RX_SYNC              (value[0] (Bit4))
- *      - PTP_INT_TYPE_RX_DELAY_REQ      (value[0] (Bit5))
- *      - PTP_INT_TYPE_RX_PDELAY_REQ    (value[0] (Bit6))
- *      - PTP_INT_TYPE_RX_PDELAY_RESP   (value[0] (Bit7))
- *      The status will be cleared after execute this API.
- */
-rtk_api_ret_t rtk_ptp_portIntStatus_set(rtk_port_t port, rtk_ptp_intStatus_t statusMask)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port is PTP port */
-    RTK_CHK_PORT_IS_PTP(port);
-
-    if ((retVal = rtl8367c_setAsicEavPortInterruptStatus(rtk_switch_port_L2P_get(port), statusMask))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_portIntStatus_get
- * Description:
- *      Get PTP port interrupt trigger status.
- * Input:
- *      port           - physical port
- * Output:
- *      pStatusMask - Interrupt status bit mask.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get interrupt trigger status when interrupt happened.
- *      The interrupt trigger status is shown in the following:
- *      - PTP_INT_TYPE_TX_SYNC              (value[0] (Bit0))
- *      - PTP_INT_TYPE_TX_DELAY_REQ      (value[0] (Bit1))
- *      - PTP_INT_TYPE_TX_PDELAY_REQ    (value[0] (Bit2))
- *      - PTP_INT_TYPE_TX_PDELAY_RESP   (value[0] (Bit3))
- *      - PTP_INT_TYPE_RX_SYNC              (value[0] (Bit4))
- *      - PTP_INT_TYPE_RX_DELAY_REQ      (value[0] (Bit5))
- *      - PTP_INT_TYPE_RX_PDELAY_REQ    (value[0] (Bit6))
- *      - PTP_INT_TYPE_RX_PDELAY_RESP   (value[0] (Bit7))
- *
- */
-rtk_api_ret_t rtk_ptp_portIntStatus_get(rtk_port_t port, rtk_ptp_intStatus_t *pStatusMask)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port is PTP port */
-    RTK_CHK_PORT_IS_PTP(port);
-
-    if(NULL == pStatusMask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicEavPortInterruptStatus(rtk_switch_port_L2P_get(port), pStatusMask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_portPtpTrap_set
- * Description:
- *      Set PTP packet trap of the specified port.
- * Input:
- *      port   - port id
- *      enable - status
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT     - invalid port id
- *      RT_ERR_INPUT    - invalid input parameter
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_portTrap_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (enable>=RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicEavTrap(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_ptp_portPtpEnable_get
- * Description:
- *      Get PTP packet trap of the specified port.
- * Input:
- *      port    - port id
- * Output:
- *      pEnable - status
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT         - invalid port id
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_ptp_portTrap_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicEavTrap(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/qos.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/qos.c
deleted file mode 100644
index 70067a3016..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/qos.c
+++ /dev/null
@@ -1,1452 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in QoS module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <qos.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_qos.h>
-#include <rtl8367c_asicdrv_fc.h>
-#include <rtl8367c_asicdrv_scheduling.h>
-
-/* Function Name:
- *      rtk_qos_init
- * Description:
- *      Configure Qos default settings with queue number assigment to each port.
- * Input:
- *      queueNum - Queue number of each port.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_QUEUE_NUM    - Invalid queue number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API will initialize related Qos setting with queue number assigment.
- *      The queue number is from 1 to 8.
- */
-rtk_api_ret_t rtk_qos_init(rtk_queue_num_t queueNum)
-{
-    CONST_T rtk_uint16 g_prioritytToQid[8][8]= {
-            {0, 0,0,0,0,0,0,0},
-            {0, 0,0,0,7,7,7,7},
-            {0, 0,0,0,1,1,7,7},
-            {0, 0,1,1,2,2,7,7},
-            {0, 0,1,1,2,3,7,7},
-            {0, 0,1,2,3,4,7,7},
-            {0, 0,1,2,3,4,5,7},
-            {0,1,2,3,4,5,6,7}
-    };
-
-    CONST_T rtk_uint32 g_priorityDecision[8] = {0x01, 0x80,0x04,0x02,0x20,0x40,0x10,0x08};
-    CONST_T rtk_uint32 g_prioritytRemap[8] = {0,1,2,3,4,5,6,7};
-
-    rtk_api_ret_t retVal;
-    rtk_uint32 qmapidx;
-    rtk_uint32 priority;
-    rtk_uint32 priDec;
-    rtk_uint32 port;
-    rtk_uint32 dscp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (queueNum <= 0 || queueNum > RTK_MAX_NUM_OF_QUEUE)
-        return RT_ERR_QUEUE_NUM;
-
-    /*Set Output Queue Number*/
-    if (RTK_MAX_NUM_OF_QUEUE == queueNum)
-        qmapidx = 0;
-    else
-        qmapidx = queueNum;
-
-    RTK_SCAN_ALL_PHY_PORTMASK(port)
-    {
-        if ((retVal = rtl8367c_setAsicOutputQueueMappingIndex(port, qmapidx)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Set Priority to Qid*/
-    for (priority = 0; priority <= RTK_PRIMAX; priority++)
-    {
-        if ((retVal = rtl8367c_setAsicPriorityToQIDMappingTable(queueNum - 1, priority, g_prioritytToQid[queueNum - 1][priority])) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Set Flow Control Type to Ingress Flow Control*/
-    if ((retVal = rtl8367c_setAsicFlowControlSelect(FC_INGRESS)) != RT_ERR_OK)
-        return retVal;
-
-
-    /*Priority Decision Order*/
-    for (priDec = 0;priDec < PRIDEC_END;priDec++)
-    {
-        if ((retVal = rtl8367c_setAsicPriorityDecision(PRIDECTBL_IDX0, priDec, g_priorityDecision[priDec])) != RT_ERR_OK)
-            return retVal;
-        if ((retVal = rtl8367c_setAsicPriorityDecision(PRIDECTBL_IDX1, priDec, g_priorityDecision[priDec])) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Set Port-based Priority to 0*/
-    RTK_SCAN_ALL_PHY_PORTMASK(port)
-    {
-        if ((retVal = rtl8367c_setAsicPriorityPortBased(port, 0)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Disable 1p Remarking*/
-    RTK_SCAN_ALL_PHY_PORTMASK(port)
-    {
-        if ((retVal = rtl8367c_setAsicRemarkingDot1pAbility(port, DISABLED)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Disable DSCP Remarking*/
-    if ((retVal = rtl8367c_setAsicRemarkingDscpAbility(DISABLED)) != RT_ERR_OK)
-        return retVal;
-
-    /*Set 1p & DSCP  Priority Remapping & Remarking*/
-    for (priority = 0; priority <= RTL8367C_PRIMAX; priority++)
-    {
-        if ((retVal = rtl8367c_setAsicPriorityDot1qRemapping(priority, g_prioritytRemap[priority])) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRemarkingDot1pParameter(priority, 0)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_setAsicRemarkingDscpParameter(priority, 0)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Set DSCP Priority*/
-    for (dscp = 0; dscp <= 63; dscp++)
-    {
-        if ((retVal = rtl8367c_setAsicPriorityDscpBased(dscp, 0)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /* Finetune B/T value */
-    if((retVal = rtl8367c_setAsicReg(0x1722, 0x1158)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_priSel_set
- * Description:
- *      Configure the priority order among different priority mechanism.
- * Input:
- *      index - Priority decision table index (0~1)
- *      pPriDec - Priority assign for port, dscp, 802.1p, cvlan, svlan, acl based priority decision.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_SEL_PRI_SOURCE   - Invalid priority decision source parameter.
- * Note:
- *      ASIC will follow user priority setting of mechanisms to select mapped queue priority for receiving frame.
- *      If two priority mechanisms are the same, the ASIC will chose the highest priority from mechanisms to
- *      assign queue priority to receiving frame.
- *      The priority sources are:
- *      - PRIDEC_PORT
- *      - PRIDEC_ACL
- *      - PRIDEC_DSCP
- *      - PRIDEC_1Q
- *      - PRIDEC_1AD
- *      - PRIDEC_CVLAN
- *      - PRIDEC_DA
- *      - PRIDEC_SA
- */
-rtk_api_ret_t rtk_qos_priSel_set(rtk_qos_priDecTbl_t index, rtk_priority_select_t *pPriDec)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port_pow;
-    rtk_uint32 dot1q_pow;
-    rtk_uint32 dscp_pow;
-    rtk_uint32 acl_pow;
-    rtk_uint32 svlan_pow;
-    rtk_uint32 cvlan_pow;
-    rtk_uint32 smac_pow;
-    rtk_uint32 dmac_pow;
-    rtk_uint32 i;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (index < 0 || index >= PRIDECTBL_END)
-        return RT_ERR_ENTRY_INDEX;
-
-    if (pPriDec->port_pri >= 8 || pPriDec->dot1q_pri >= 8 || pPriDec->acl_pri >= 8 || pPriDec->dscp_pri >= 8 ||
-       pPriDec->cvlan_pri >= 8 || pPriDec->svlan_pri >= 8 || pPriDec->dmac_pri >= 8 || pPriDec->smac_pri >= 8)
-        return RT_ERR_QOS_SEL_PRI_SOURCE;
-
-    port_pow = 1;
-    for (i = pPriDec->port_pri; i > 0; i--)
-        port_pow = (port_pow)*2;
-
-    dot1q_pow = 1;
-    for (i = pPriDec->dot1q_pri; i > 0; i--)
-        dot1q_pow = (dot1q_pow)*2;
-
-    acl_pow = 1;
-    for (i = pPriDec->acl_pri; i > 0; i--)
-        acl_pow = (acl_pow)*2;
-
-    dscp_pow = 1;
-    for (i = pPriDec->dscp_pri; i > 0; i--)
-        dscp_pow = (dscp_pow)*2;
-
-    svlan_pow = 1;
-    for (i = pPriDec->svlan_pri; i > 0; i--)
-        svlan_pow = (svlan_pow)*2;
-
-    cvlan_pow = 1;
-    for (i = pPriDec->cvlan_pri; i > 0; i--)
-        cvlan_pow = (cvlan_pow)*2;
-
-    dmac_pow = 1;
-    for (i = pPriDec->dmac_pri; i > 0; i--)
-        dmac_pow = (dmac_pow)*2;
-
-    smac_pow = 1;
-    for (i = pPriDec->smac_pri; i > 0; i--)
-        smac_pow = (smac_pow)*2;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_PORT, port_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_ACL, acl_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_DSCP, dscp_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_1Q, dot1q_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_1AD, svlan_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_CVLAN, cvlan_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_DA, dmac_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPriorityDecision(index, PRIDEC_SA, smac_pow)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_priSel_get
- * Description:
- *      Get the priority order configuration among different priority mechanism.
- * Input:
- *      index - Priority decision table index (0~1)
- * Output:
- *      pPriDec - Priority assign for port, dscp, 802.1p, cvlan, svlan, acl based priority decision .
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      ASIC will follow user priority setting of mechanisms to select mapped queue priority for receiving frame.
- *      If two priority mechanisms are the same, the ASIC will chose the highest priority from mechanisms to
- *      assign queue priority to receiving frame.
- *      The priority sources are:
- *      - PRIDEC_PORT,
- *      - PRIDEC_ACL,
- *      - PRIDEC_DSCP,
- *      - PRIDEC_1Q,
- *      - PRIDEC_1AD,
- *      - PRIDEC_CVLAN,
- *      - PRIDEC_DA,
- *      - PRIDEC_SA,
- */
-rtk_api_ret_t rtk_qos_priSel_get(rtk_qos_priDecTbl_t index, rtk_priority_select_t *pPriDec)
-{
-
-    rtk_api_ret_t retVal;
-    rtk_int32 i;
-    rtk_uint32 port_pow;
-    rtk_uint32 dot1q_pow;
-    rtk_uint32 dscp_pow;
-    rtk_uint32 acl_pow;
-    rtk_uint32 svlan_pow;
-    rtk_uint32 cvlan_pow;
-    rtk_uint32 smac_pow;
-    rtk_uint32 dmac_pow;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (index < 0 || index >= PRIDECTBL_END)
-        return RT_ERR_ENTRY_INDEX;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_PORT, &port_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_ACL, &acl_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_DSCP, &dscp_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_1Q, &dot1q_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_1AD, &svlan_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_CVLAN, &cvlan_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_DA, &dmac_pow)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPriorityDecision(index, PRIDEC_SA, &smac_pow)) != RT_ERR_OK)
-        return retVal;
-
-    for (i = 31; i >= 0; i--)
-    {
-        if (port_pow & (1 << i))
-        {
-            pPriDec->port_pri = i;
-            break;
-        }
-    }
-
-    for (i = 31; i >= 0; i--)
-    {
-        if (dot1q_pow & (1 << i))
-        {
-            pPriDec->dot1q_pri = i;
-            break;
-        }
-    }
-
-    for (i = 31; i >= 0; i--)
-    {
-        if (acl_pow & (1 << i))
-        {
-            pPriDec->acl_pri = i;
-            break;
-        }
-    }
-
-    for (i = 31; i >= 0; i--)
-    {
-        if (dscp_pow & (1 << i))
-        {
-            pPriDec->dscp_pri = i;
-            break;
-        }
-    }
-
-    for (i = 31; i >= 0; i--)
-    {
-        if (svlan_pow & (1 << i))
-        {
-            pPriDec->svlan_pri = i;
-            break;
-        }
-    }
-
-    for (i = 31;i  >= 0; i--)
-    {
-        if (cvlan_pow & (1 << i))
-        {
-            pPriDec->cvlan_pri = i;
-            break;
-        }
-    }
-
-    for (i = 31; i >= 0; i--)
-    {
-        if (dmac_pow&(1<<i))
-        {
-            pPriDec->dmac_pri = i;
-            break;
-        }
-    }
-
-    for (i = 31; i >= 0; i--)
-    {
-        if (smac_pow & (1 << i))
-        {
-            pPriDec->smac_pri = i;
-            break;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pPriRemap_set
- * Description:
- *      Configure 1Q priorities mapping to internal absolute priority.
- * Input:
- *      dot1p_pri   - 802.1p priority value.
- *      int_pri     - internal priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of 802.1Q assignment for internal asic priority, and it is used for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_qos_1pPriRemap_set(rtk_pri_t dot1p_pri, rtk_pri_t int_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (dot1p_pri > RTL8367C_PRIMAX || int_pri > RTL8367C_PRIMAX)
-        return  RT_ERR_VLAN_PRIORITY;
-
-    if ((retVal = rtl8367c_setAsicPriorityDot1qRemapping(dot1p_pri, int_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pPriRemap_get
- * Description:
- *      Get 1Q priorities mapping to internal absolute priority.
- * Input:
- *      dot1p_pri - 802.1p priority value .
- * Output:
- *      pInt_pri - internal priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_VLAN_PRIORITY    - Invalid priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      Priority of 802.1Q assigment for internal asic priority, and it is uesed for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_qos_1pPriRemap_get(rtk_pri_t dot1p_pri, rtk_pri_t *pInt_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (dot1p_pri > RTL8367C_PRIMAX)
-        return  RT_ERR_QOS_INT_PRIORITY;
-
-    if ((retVal = rtl8367c_getAsicPriorityDot1qRemapping(dot1p_pri, pInt_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dscpPriRemap_set
- * Description:
- *      Map dscp value to internal priority.
- * Input:
- *      dscp    - Dscp value of receiving frame
- *      int_pri - internal priority value .
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid DSCP value.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The Differentiated Service Code Point is a selector for router's per-hop behaviors. As a selector, there is no implication that a numerically
- *      greater DSCP implies a better network service. As can be seen, the DSCP totally overlaps the old precedence field of TOS. So if values of
- *      DSCP are carefully chosen then backward compatibility can be achieved.
- */
-rtk_api_ret_t rtk_qos_dscpPriRemap_set(rtk_dscp_t dscp, rtk_pri_t int_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (int_pri > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if (dscp > RTL8367C_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    if ((retVal = rtl8367c_setAsicPriorityDscpBased(dscp, int_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dscpPriRemap_get
- * Description:
- *      Get dscp value to internal priority.
- * Input:
- *      dscp - Dscp value of receiving frame
- * Output:
- *      pInt_pri - internal priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid DSCP value.
- * Note:
- *      The Differentiated Service Code Point is a selector for router's per-hop behaviors. As a selector, there is no implication that a numerically
- *      greater DSCP implies a better network service. As can be seen, the DSCP totally overlaps the old precedence field of TOS. So if values of
- *      DSCP are carefully chosen then backward compatibility can be achieved.
- */
-rtk_api_ret_t rtk_qos_dscpPriRemap_get(rtk_dscp_t dscp, rtk_pri_t *pInt_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (dscp > RTL8367C_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    if ((retVal = rtl8367c_getAsicPriorityDscpBased(dscp, pInt_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_portPri_set
- * Description:
- *      Configure priority usage to each port.
- * Input:
- *      port - Port id.
- *      int_pri - internal priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_SEL_PORT_PRI - Invalid port priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can set priority of port assignments for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_qos_portPri_set(rtk_port_t port, rtk_pri_t int_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (int_pri > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if ((retVal = rtl8367c_setAsicPriorityPortBased(rtk_switch_port_L2P_get(port), int_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_portPri_get
- * Description:
- *      Get priority usage to each port.
- * Input:
- *      port - Port id.
- * Output:
- *      pInt_pri - internal priority value.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get priority of port assignments for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_qos_portPri_get(rtk_port_t port, rtk_pri_t *pInt_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicPriorityPortBased(rtk_switch_port_L2P_get(port), pInt_pri)) != RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_queueNum_set
- * Description:
- *      Set output queue number for each port.
- * Input:
- *      port    - Port id.
- *      index   - Mapping queue number (1~8)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_QUEUE_NUM    - Invalid queue number.
- * Note:
- *      The API can set the output queue number of the specified port. The queue number is from 1 to 8.
- */
-rtk_api_ret_t rtk_qos_queueNum_set(rtk_port_t port, rtk_queue_num_t queue_num)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((0 == queue_num) || (queue_num > RTK_MAX_NUM_OF_QUEUE))
-        return RT_ERR_FAILED;
-
-    if (RTK_MAX_NUM_OF_QUEUE == queue_num)
-        queue_num = 0;
-
-    if ((retVal = rtl8367c_setAsicOutputQueueMappingIndex(rtk_switch_port_L2P_get(port), queue_num)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_queueNum_get
- * Description:
- *      Get output queue number.
- * Input:
- *      port - Port id.
- * Output:
- *      pQueue_num - Mapping queue number
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API will return the output queue number of the specified port. The queue number is from 1 to 8.
- */
-rtk_api_ret_t rtk_qos_queueNum_get(rtk_port_t port, rtk_queue_num_t *pQueue_num)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 qidx;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicOutputQueueMappingIndex(rtk_switch_port_L2P_get(port), &qidx)) != RT_ERR_OK)
-        return retVal;
-
-    if (0 == qidx)
-        *pQueue_num = 8;
-    else
-        *pQueue_num = qidx;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_priMap_set
- * Description:
- *      Set output queue number for each port.
- * Input:
- *      queue_num   - Queue number usage.
- *      pPri2qid    - Priority mapping to queue ID.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_QUEUE_NUM        - Invalid queue number.
- *      RT_ERR_QUEUE_ID         - Invalid queue id.
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      ASIC supports priority mapping to queue with different queue number from 1 to 8.
- *      For different queue numbers usage, ASIC supports different internal available queue IDs.
- */
-rtk_api_ret_t rtk_qos_priMap_set(rtk_queue_num_t queue_num, rtk_qos_pri2queue_t *pPri2qid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pri;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((0 == queue_num) || (queue_num > RTK_MAX_NUM_OF_QUEUE))
-        return RT_ERR_QUEUE_NUM;
-
-    for (pri = 0; pri <= RTK_PRIMAX; pri++)
-    {
-        if (pPri2qid->pri2queue[pri] > RTK_QIDMAX)
-            return RT_ERR_QUEUE_ID;
-
-        if ((retVal = rtl8367c_setAsicPriorityToQIDMappingTable(queue_num - 1, pri, pPri2qid->pri2queue[pri])) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_priMap_get
- * Description:
- *      Get priority to queue ID mapping table parameters.
- * Input:
- *      queue_num - Queue number usage.
- * Output:
- *      pPri2qid - Priority mapping to queue ID.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_QUEUE_NUM    - Invalid queue number.
- * Note:
- *      The API can return the mapping queue id of the specified priority and queue number.
- *      The queue number is from 1 to 8.
- */
-rtk_api_ret_t rtk_qos_priMap_get(rtk_queue_num_t queue_num, rtk_qos_pri2queue_t *pPri2qid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pri;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((0 == queue_num) || (queue_num > RTK_MAX_NUM_OF_QUEUE))
-        return RT_ERR_QUEUE_NUM;
-
-    for (pri = 0; pri <= RTK_PRIMAX; pri++)
-    {
-        if ((retVal = rtl8367c_getAsicPriorityToQIDMappingTable(queue_num-1, pri, &pPri2qid->pri2queue[pri])) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_schedulingQueue_set
- * Description:
- *      Set weight and type of queues in dedicated port.
- * Input:
- *      port        - Port id.
- *      pQweights   - The array of weights for WRR/WFQ queue (0 for STRICT_PRIORITY queue).
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_QUEUE_WEIGHT - Invalid queue weight.
- * Note:
- *      The API can set weight and type, strict priority or weight fair queue (WFQ) for
- *      dedicated port for using queues. If queue id is not included in queue usage,
- *      then its type and weight setting in dummy for setting. There are priorities
- *      as queue id in strict queues. It means strict queue id 5 carrying higher priority
- *      than strict queue id 4. The WFQ queue weight is from 1 to 127, and weight 0 is
- *      for strict priority queue type.
- */
-rtk_api_ret_t rtk_qos_schedulingQueue_set(rtk_port_t port, rtk_qos_queue_weights_t *pQweights)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 qid;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    for (qid = 0; qid < RTL8367C_QUEUENO; qid ++)
-    {
-
-        if (pQweights->weights[qid] > QOS_WEIGHT_MAX)
-            return RT_ERR_QOS_QUEUE_WEIGHT;
-
-        if (0 == pQweights->weights[qid])
-        {
-            if ((retVal = rtl8367c_setAsicQueueType(rtk_switch_port_L2P_get(port), qid, QTYPE_STRICT)) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-        {
-            if ((retVal = rtl8367c_setAsicQueueType(rtk_switch_port_L2P_get(port), qid, QTYPE_WFQ)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicWFQWeight(rtk_switch_port_L2P_get(port),qid, pQweights->weights[qid])) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_schedulingQueue_get
- * Description:
- *      Get weight and type of queues in dedicated port.
- * Input:
- *      port - Port id.
- * Output:
- *      pQweights - The array of weights for WRR/WFQ queue (0 for STRICT_PRIORITY queue).
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get weight and type, strict priority or weight fair queue (WFQ) for dedicated port for using queues.
- *      The WFQ queue weight is from 1 to 127, and weight 0 is for strict priority queue type.
- */
-rtk_api_ret_t rtk_qos_schedulingQueue_get(rtk_port_t port, rtk_qos_queue_weights_t *pQweights)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 qid,qtype,qweight;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    for (qid = 0; qid < RTL8367C_QUEUENO; qid++)
-    {
-        if ((retVal = rtl8367c_getAsicQueueType(rtk_switch_port_L2P_get(port), qid, &qtype)) != RT_ERR_OK)
-            return retVal;
-
-        if (QTYPE_STRICT == qtype)
-        {
-            pQweights->weights[qid] = 0;
-        }
-        else if (QTYPE_WFQ == qtype)
-        {
-            if ((retVal = rtl8367c_getAsicWFQWeight(rtk_switch_port_L2P_get(port), qid, &qweight)) != RT_ERR_OK)
-                return retVal;
-            pQweights->weights[qid] = qweight;
-        }
-    }
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pRemarkEnable_set
- * Description:
- *      Set 1p Remarking state
- * Input:
- *      port        - Port id.
- *      enable      - State of per-port 1p Remarking
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid enable parameter.
- * Note:
- *      The API can enable or disable 802.1p remarking ability for whole system.
- *      The status of 802.1p remark:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_qos_1pRemarkEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicRemarkingDot1pAbility(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pRemarkEnable_get
- * Description:
- *      Get 802.1p remarking ability.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - Status of 802.1p remark.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get 802.1p remarking ability.
- *      The status of 802.1p remark:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_qos_1pRemarkEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicRemarkingDot1pAbility(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pRemark_set
- * Description:
- *      Set 802.1p remarking parameter.
- * Input:
- *      int_pri     - Internal priority value.
- *      dot1p_pri   - 802.1p priority value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_VLAN_PRIORITY    - Invalid 1p priority.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can set 802.1p parameters source priority and new priority.
- */
-rtk_api_ret_t rtk_qos_1pRemark_set(rtk_pri_t int_pri, rtk_pri_t dot1p_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (int_pri > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if (dot1p_pri > RTL8367C_PRIMAX)
-        return RT_ERR_VLAN_PRIORITY;
-
-    if ((retVal = rtl8367c_setAsicRemarkingDot1pParameter(int_pri, dot1p_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pRemark_get
- * Description:
- *      Get 802.1p remarking parameter.
- * Input:
- *      int_pri - Internal priority value.
- * Output:
- *      pDot1p_pri - 802.1p priority value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can get 802.1p remarking parameters. It would return new priority of ingress priority.
- */
-rtk_api_ret_t rtk_qos_1pRemark_get(rtk_pri_t int_pri, rtk_pri_t *pDot1p_pri)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (int_pri > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if ((retVal = rtl8367c_getAsicRemarkingDot1pParameter(int_pri, pDot1p_pri)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pRemarkSrcSel_set
- * Description:
- *      Set remarking source of 802.1p remarking.
- * Input:
- *      type      - remarking source
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID  - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
-
- * Note:
- *      The API can configure 802.1p remark functionality to map original 802.1p value or internal
- *      priority to TX DSCP value.
- */
-rtk_api_ret_t rtk_qos_1pRemarkSrcSel_set(rtk_qos_1pRmkSrc_t type)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= DOT1P_RMK_SRC_END )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if ((retVal = rtl8367c_setAsicRemarkingDot1pSrc(type)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_1pRemarkSrcSel_get
- * Description:
- *      Get remarking source of 802.1p remarking.
- * Input:
- *      none
- * Output:
- *      pType      - remarking source
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
- *      RT_ERR_NULL_POINTER     - input parameter may be null pointer
-
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_qos_1pRemarkSrcSel_get(rtk_qos_1pRmkSrc_t *pType)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicRemarkingDot1pSrc(pType)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_qos_dscpRemarkEnable_set
- * Description:
- *      Set DSCP remarking ability.
- * Input:
- *      port    - Port id.
- *      enable  - status of DSCP remark.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- *      RT_ERR_ENABLE           - Invalid enable parameter.
- * Note:
- *      The API can enable or disable DSCP remarking ability for whole system.
- *      The status of DSCP remark:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_qos_dscpRemarkEnable_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /*for whole system function, the port value should be 0xFF*/
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicRemarkingDscpAbility(enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dscpRemarkEnable_get
- * Description:
- *      Get DSCP remarking ability.
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - status of DSCP remarking.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get DSCP remarking ability.
- *      The status of DSCP remark:
- *      - DISABLED
- *      - ENABLED
- */
-rtk_api_ret_t rtk_qos_dscpRemarkEnable_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /*for whole system function, the port value should be 0xFF*/
-    if (port != RTK_WHOLE_SYSTEM)
-        return RT_ERR_PORT_ID;
-
-    if ((retVal = rtl8367c_getAsicRemarkingDscpAbility(pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dscpRemark_set
- * Description:
- *      Set DSCP remarking parameter.
- * Input:
- *      int_pri - Internal priority value.
- *      dscp    - DSCP value.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid DSCP value.
- * Note:
- *      The API can set DSCP value and mapping priority.
- */
-rtk_api_ret_t rtk_qos_dscpRemark_set(rtk_pri_t int_pri, rtk_dscp_t dscp)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (int_pri > RTK_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if (dscp > RTK_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    if ((retVal = rtl8367c_setAsicRemarkingDscpParameter(int_pri, dscp)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_qos_dscpRemark_get
- * Description:
- *      Get DSCP remarking parameter.
- * Input:
- *      int_pri - Internal priority value.
- * Output:
- *      Dscp - DSCP value.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority.
- * Note:
- *      The API can get DSCP parameters. It would return DSCP value for mapping priority.
- */
-rtk_api_ret_t rtk_qos_dscpRemark_get(rtk_pri_t int_pri, rtk_dscp_t *pDscp)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (int_pri > RTK_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if ((retVal = rtl8367c_getAsicRemarkingDscpParameter(int_pri, pDscp)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dscpRemarkSrcSel_set
- * Description:
- *      Set remarking source of DSCP remarking.
- * Input:
- *      type      - remarking source
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID  - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
-
- * Note:
- *      The API can configure DSCP remark functionality to map original DSCP value or internal
- *      priority to TX DSCP value.
- */
-rtk_api_ret_t rtk_qos_dscpRemarkSrcSel_set(rtk_qos_dscpRmkSrc_t type)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= DSCP_RMK_SRC_END )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if ((retVal = rtl8367c_setAsicRemarkingDscpSrc(type)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dcpRemarkSrcSel_get
- * Description:
- *      Get remarking source of DSCP remarking.
- * Input:
- *      none
- * Output:
- *      pType      - remarking source
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
- *      RT_ERR_NULL_POINTER     - input parameter may be null pointer
-
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_qos_dscpRemarkSrcSel_get(rtk_qos_dscpRmkSrc_t *pType)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicRemarkingDscpSrc(pType)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dscpRemark2Dscp_set
- * Description:
- *      Set DSCP to remarked DSCP mapping.
- * Input:
- *      dscp    - DSCP value
- *      rmkDscp - remarked DSCP value
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid dscp value
- * Note:
- *      dscp parameter can be DSCP value or internal priority according to configuration of API
- *      dal_apollomp_qos_dscpRemarkSrcSel_set(), because DSCP remark functionality can map original DSCP
- *      value or internal priority to TX DSCP value.
- */
-rtk_api_ret_t rtk_qos_dscpRemark2Dscp_set(rtk_dscp_t dscp, rtk_dscp_t rmkDscp)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((dscp > RTK_DSCPMAX) || (rmkDscp > RTK_DSCPMAX))
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    if ((retVal = rtl8367c_setAsicRemarkingDscp2Dscp(dscp, rmkDscp)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_dscpRemark2Dscp_get
- * Description:
- *      Get DSCP to remarked DSCP mapping.
- * Input:
- *      dscp    - DSCP value
- * Output:
- *      pDscp   - remarked DSCP value
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid dscp value
- *      RT_ERR_NULL_POINTER     - NULL pointer
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_qos_dscpRemark2Dscp_get(rtk_dscp_t dscp, rtk_dscp_t *pDscp)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (dscp > RTK_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    if ((retVal = rtl8367c_getAsicRemarkingDscp2Dscp(dscp, pDscp)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_portPriSelIndex_set
- * Description:
- *      Configure priority decision index to each port.
- * Input:
- *      port - Port id.
- *      index - priority decision index.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_ENTRY_INDEX - Invalid entry index.
- * Note:
- *      The API can set priority of port assignments for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_qos_portPriSelIndex_set(rtk_port_t port, rtk_qos_priDecTbl_t index)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (index >= PRIDECTBL_END )
-        return RT_ERR_ENTRY_INDEX;
-
-    if ((retVal = rtl8367c_setAsicPortPriorityDecisionIndex(rtk_switch_port_L2P_get(port), index)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_qos_portPriSelIndex_get
- * Description:
- *      Get priority decision index from each port.
- * Input:
- *      port - Port id.
- * Output:
- *      pIndex - priority decision index.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get priority of port assignments for queue usage and packet scheduling.
- */
-rtk_api_ret_t rtk_qos_portPriSelIndex_get(rtk_port_t port, rtk_qos_priDecTbl_t *pIndex)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicPortPriorityDecisionIndex(rtk_switch_port_L2P_get(port), pIndex)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rate.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rate.c
deleted file mode 100644
index a077e0c5cc..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rate.c
+++ /dev/null
@@ -1,607 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in rate module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <rate.h>
-#include <qos.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_meter.h>
-#include <rtl8367c_asicdrv_inbwctrl.h>
-#include <rtl8367c_asicdrv_scheduling.h>
-
-/* Function Name:
- *      rtk_rate_shareMeter_set
- * Description:
- *      Set meter configuration
- * Input:
- *      index       - shared meter index
- *      type        - shared meter type
- *      rate        - rate of share meter
- *      ifg_include - include IFG or not, ENABLE:include DISABLE:exclude
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- *      RT_ERR_RATE             - Invalid rate
- *      RT_ERR_INPUT            - Invalid input parameters
- * Note:
- *      The API can set shared meter rate and ifg include for each meter.
- *      The rate unit is 1 kbps and the range is from 8k to 1048568k if type is METER_TYPE_KBPS and
- *      the granularity of rate is 8 kbps.
- *      The rate unit is packets per second and the range is 1 ~ 0x1FFF if type is METER_TYPE_PPS.
- *      The ifg_include parameter is used
- *      for rate calculation with/without inter-frame-gap and preamble.
- */
-rtk_api_ret_t rtk_rate_shareMeter_set(rtk_meter_id_t index, rtk_meter_type_t type, rtk_rate_t rate, rtk_enable_t ifg_include)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (index > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    if (type >= METER_TYPE_END)
-        return RT_ERR_INPUT;
-
-    if (ifg_include >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    switch (type)
-    {
-        case METER_TYPE_KBPS:
-            if (rate > RTL8367C_QOS_RATE_INPUT_MAX_HSG || rate < RTL8367C_QOS_RATE_INPUT_MIN)
-                return RT_ERR_RATE ;
-
-            if ((retVal = rtl8367c_setAsicShareMeter(index, rate >> 3, ifg_include)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case METER_TYPE_PPS:
-            if (rate > RTL8367C_QOS_PPS_INPUT_MAX || rate < RTL8367C_QOS_PPS_INPUT_MIN)
-                return RT_ERR_RATE ;
-
-            if ((retVal = rtl8367c_setAsicShareMeter(index, rate, ifg_include)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        default:
-            return RT_ERR_INPUT;
-    }
-
-    /* Set Type */
-    if ((retVal = rtl8367c_setAsicShareMeterType(index, (rtk_uint32)type)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_shareMeter_get
- * Description:
- *      Get meter configuration
- * Input:
- *      index        - shared meter index
- * Output:
- *      pType        - Meter Type
- *      pRate        - pointer of rate of share meter
- *      pIfg_include - include IFG or not, ENABLE:include DISABLE:exclude
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_shareMeter_get(rtk_meter_id_t index, rtk_meter_type_t *pType, rtk_rate_t *pRate, rtk_enable_t *pIfg_include)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (index > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(NULL == pType)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pRate)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pIfg_include)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicShareMeter(index, &regData, pIfg_include)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicShareMeterType(index, (rtk_uint32 *)pType)) != RT_ERR_OK)
-        return retVal;
-
-    if(*pType == METER_TYPE_KBPS)
-        *pRate = regData<<3;
-    else
-        *pRate = regData;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_shareMeterBucket_set
- * Description:
- *      Set meter Bucket Size
- * Input:
- *      index        - shared meter index
- *      bucket_size  - Bucket Size
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_INPUT            - Error Input
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      The API can set shared meter bucket size.
- */
-rtk_api_ret_t rtk_rate_shareMeterBucket_set(rtk_meter_id_t index, rtk_uint32 bucket_size)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (index > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(bucket_size > RTL8367C_METERBUCKETSIZEMAX)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicShareMeterBucketSize(index, bucket_size)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_shareMeterBucket_get
- * Description:
- *      Get meter Bucket Size
- * Input:
- *      index        - shared meter index
- * Output:
- *      pBucket_size - Bucket Size
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      The API can get shared meter bucket size.
- */
-rtk_api_ret_t rtk_rate_shareMeterBucket_get(rtk_meter_id_t index, rtk_uint32 *pBucket_size)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (index > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(NULL == pBucket_size)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicShareMeterBucketSize(index, pBucket_size)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_igrBandwidthCtrlRate_set
- * Description:
- *      Set port ingress bandwidth control
- * Input:
- *      port        - Port id
- *      rate        - Rate of share meter
- *      ifg_include - include IFG or not, ENABLE:include DISABLE:exclude
- *      fc_enable   - enable flow control or not, ENABLE:use flow control DISABLE:drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_ENABLE       - Invalid IFG parameter.
- *      RT_ERR_INBW_RATE    - Invalid ingress rate parameter.
- * Note:
- *      The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *      The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-rtk_api_ret_t rtk_rate_igrBandwidthCtrlRate_set(rtk_port_t port, rtk_rate_t rate, rtk_enable_t ifg_include, rtk_enable_t fc_enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(ifg_include >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(fc_enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if(rtk_switch_isHsgPort(port) == RT_ERR_OK)
-    {
-        if ((rate > RTL8367C_QOS_RATE_INPUT_MAX_HSG) || (rate < RTL8367C_QOS_RATE_INPUT_MIN))
-            return RT_ERR_QOS_EBW_RATE ;
-    }
-    else
-    {
-        if ((rate > RTL8367C_QOS_RATE_INPUT_MAX) || (rate < RTL8367C_QOS_RATE_INPUT_MIN))
-            return RT_ERR_QOS_EBW_RATE ;
-    }
-
-    if ((retVal = rtl8367c_setAsicPortIngressBandwidth(rtk_switch_port_L2P_get(port), rate>>3, ifg_include,fc_enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_igrBandwidthCtrlRate_get
- * Description:
- *      Get port ingress bandwidth control
- * Input:
- *      port - Port id
- * Output:
- *      pRate           - Rate of share meter
- *      pIfg_include    - Rate's calculation including IFG, ENABLE:include DISABLE:exclude
- *      pFc_enable      - enable flow control or not, ENABLE:use flow control DISABLE:drop
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *     The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *     The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-rtk_api_ret_t rtk_rate_igrBandwidthCtrlRate_get(rtk_port_t port, rtk_rate_t *pRate, rtk_enable_t *pIfg_include, rtk_enable_t *pFc_enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pIfg_include)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pFc_enable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortIngressBandwidth(rtk_switch_port_L2P_get(port), &regData, pIfg_include, pFc_enable)) != RT_ERR_OK)
-        return retVal;
-
-    *pRate = regData<<3;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_egrBandwidthCtrlRate_set
- * Description:
- *      Set port egress bandwidth control
- * Input:
- *      port        - Port id
- *      rate        - Rate of egress bandwidth
- *      ifg_include - include IFG or not, ENABLE:include DISABLE:exclude
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_QOS_EBW_RATE - Invalid egress bandwidth/rate
- * Note:
- *     The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *     The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-rtk_api_ret_t rtk_rate_egrBandwidthCtrlRate_set( rtk_port_t port, rtk_rate_t rate,  rtk_enable_t ifg_include)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(rtk_switch_isHsgPort(port) == RT_ERR_OK)
-    {
-        if ((rate > RTL8367C_QOS_RATE_INPUT_MAX_HSG) || (rate < RTL8367C_QOS_RATE_INPUT_MIN))
-            return RT_ERR_QOS_EBW_RATE ;
-    }
-    else
-    {
-        if ((rate > RTL8367C_QOS_RATE_INPUT_MAX) || (rate < RTL8367C_QOS_RATE_INPUT_MIN))
-            return RT_ERR_QOS_EBW_RATE ;
-    }
-
-    if (ifg_include >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicPortEgressRate(rtk_switch_port_L2P_get(port), rate>>3)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPortEgressRateIfg(ifg_include)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_egrBandwidthCtrlRate_get
- * Description:
- *      Get port egress bandwidth control
- * Input:
- *      port - Port id
- * Output:
- *      pRate           - Rate of egress bandwidth
- *      pIfg_include    - Rate's calculation including IFG, ENABLE:include DISABLE:exclude
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *     The rate unit is 1 kbps and the range is from 8k to 1048568k. The granularity of rate is 8 kbps.
- *     The ifg_include parameter is used for rate calculation with/without inter-frame-gap and preamble.
- */
-rtk_api_ret_t rtk_rate_egrBandwidthCtrlRate_get(rtk_port_t port, rtk_rate_t *pRate, rtk_enable_t *pIfg_include)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pRate)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pIfg_include)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortEgressRate(rtk_switch_port_L2P_get(port), &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pRate = regData << 3;
-
-    if ((retVal = rtl8367c_getAsicPortEgressRateIfg((rtk_uint32*)pIfg_include)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlEnable_get
- * Description:
- *      Get enable status of egress bandwidth control on specified queue.
- * Input:
- *      unit    - unit id
- *      port    - port id
- *      queue   - queue id
- * Output:
- *      pEnable - Pointer to enable status of egress queue bandwidth control
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_NULL_POINTER     - input parameter may be null pointer
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rate_egrQueueBwCtrlEnable_get(rtk_port_t port, rtk_qid_t queue, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    /*for whole port function, the queue value should be 0xFF*/
-    if (queue != RTK_WHOLE_SYSTEM)
-        return RT_ERR_QUEUE_ID;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicAprEnable(rtk_switch_port_L2P_get(port),pEnable))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlEnable_set
- * Description:
- *      Set enable status of egress bandwidth control on specified queue.
- * Input:
- *      port   - port id
- *      queue  - queue id
- *      enable - enable status of egress queue bandwidth control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_INPUT            - invalid input parameter
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rate_egrQueueBwCtrlEnable_set(rtk_port_t port, rtk_qid_t queue, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    /*for whole port function, the queue value should be 0xFF*/
-    if (queue != RTK_WHOLE_SYSTEM)
-        return RT_ERR_QUEUE_ID;
-
-    if (enable>=RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicAprEnable(rtk_switch_port_L2P_get(port), enable))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlRate_get
- * Description:
- *      Get rate of egress bandwidth control on specified queue.
- * Input:
- *      port  - port id
- *      queue - queue id
- *      pIndex - shared meter index
- * Output:
- *      pRate - pointer to rate of egress queue bandwidth control
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter id
- * Note:
- *    The actual rate control is set in shared meters.
- *    The unit of granularity is 8Kbps.
- */
-rtk_api_ret_t rtk_rate_egrQueueBwCtrlRate_get(rtk_port_t port, rtk_qid_t queue, rtk_meter_id_t *pIndex)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 offset_idx;
-    rtk_uint32 phy_port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (queue >= RTK_MAX_NUM_OF_QUEUE)
-        return RT_ERR_QUEUE_ID;
-
-    if(NULL == pIndex)
-        return RT_ERR_NULL_POINTER;
-
-    phy_port = rtk_switch_port_L2P_get(port);
-    if ((retVal=rtl8367c_getAsicAprMeter(phy_port, queue,&offset_idx))!=RT_ERR_OK)
-        return retVal;
-
-    *pIndex = offset_idx + ((phy_port%4)*8);
-
-     return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_rate_egrQueueBwCtrlRate_set
- * Description:
- *      Set rate of egress bandwidth control on specified queue.
- * Input:
- *      port  - port id
- *      queue - queue id
- *      index - shared meter index
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_QUEUE_ID         - invalid queue id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter id
- * Note:
- *    The actual rate control is set in shared meters.
- *    The unit of granularity is 8Kbps.
- */
-rtk_api_ret_t rtk_rate_egrQueueBwCtrlRate_set(rtk_port_t port, rtk_qid_t queue, rtk_meter_id_t index)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 offset_idx;
-    rtk_uint32 phy_port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (queue >= RTK_MAX_NUM_OF_QUEUE)
-        return RT_ERR_QUEUE_ID;
-
-    if (index > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    phy_port = rtk_switch_port_L2P_get(port);
-    if (index < ((phy_port%4)*8) ||  index > (7 + (phy_port%4)*8))
-        return RT_ERR_FILTER_METER_ID;
-
-    offset_idx = index - ((phy_port%4)*8);
-
-    if ((retVal=rtl8367c_setAsicAprMeter(phy_port,queue,offset_idx))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rldp.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rldp.c
deleted file mode 100644
index d3ca029751..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rldp.c
+++ /dev/null
@@ -1,468 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (¶g¤T, 08 ¤T¤ë 2017) $
- *
- * Purpose : Declaration of RLDP and RLPP API
- *
- * Feature : The file have include the following module and sub-modules
- *           1) RLDP and RLPP configuration and status
- *
- */
-
-
-/*
- * Include Files
- */
-#include <rtk_switch.h>
-#include <rtk_error.h>
-//#include <rtk_types.h>
-#include <rldp.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_rldp.h>
-
-/*
- * Symbol Definition
- */
-
-
-/*
- * Data Declaration
- */
-
-
-/*
- * Macro Declaration
- */
-
-
-/*
- * Function Declaration
- */
-
-/* Module Name : RLDP */
-
-/* Function Name:
- *      rtk_rldp_config_set
- * Description:
- *      Set RLDP module configuration
- * Input:
- *      pConfig - configuration structure of RLDP
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rldp_config_set(rtk_rldp_config_t *pConfig)
-{
-    rtk_api_ret_t retVal;
-    ether_addr_t magic;
-    rtk_uint32 pmsk;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (pConfig->rldp_enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (pConfig->trigger_mode >= RTK_RLDP_TRIGGER_END)
-        return RT_ERR_INPUT;
-
-    if (pConfig->compare_type >= RTK_RLDP_CMPTYPE_END)
-        return RT_ERR_INPUT;
-
-    if (pConfig->num_check >= RTK_RLDP_NUM_MAX)
-        return RT_ERR_INPUT;
-
-    if (pConfig->interval_check >= RTK_RLDP_INTERVAL_MAX)
-        return RT_ERR_INPUT;
-
-    if (pConfig->num_loop >= RTK_RLDP_NUM_MAX)
-        return RT_ERR_INPUT;
-
-    if (pConfig->interval_loop >= RTK_RLDP_INTERVAL_MAX)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_getAsicRldpTxPortmask(&pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldpTxPortmask(0x00))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldpTxPortmask(pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldp(pConfig->rldp_enable))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldpTriggerMode(pConfig->trigger_mode))!=RT_ERR_OK)
-        return retVal;
-
-    memcpy(&magic, &pConfig->magic, sizeof(ether_addr_t));
-    if ((retVal = rtl8367c_setAsicRldpMagicNum(magic))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldpCompareRandomNumber(pConfig->compare_type))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldpCompareRandomNumber(pConfig->compare_type))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldpCheckingStatePara(pConfig->num_check, pConfig->interval_check))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRldpLoopStatePara(pConfig->num_loop, pConfig->interval_loop))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_rldp_config_get
- * Description:
- *      Get RLDP module configuration
- * Input:
- *      None
- * Output:
- *      pConfig - configuration structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rldp_config_get(rtk_rldp_config_t *pConfig)
-{
-    rtk_api_ret_t retVal;
-    ether_addr_t magic;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicRldp(&pConfig->rldp_enable))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicRldpTriggerMode(&pConfig->trigger_mode))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicRldpMagicNum(&magic))!=RT_ERR_OK)
-        return retVal;
-    memcpy(&pConfig->magic, &magic, sizeof(ether_addr_t));
-
-    if ((retVal = rtl8367c_getAsicRldpCompareRandomNumber(&pConfig->compare_type))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicRldpCompareRandomNumber(&pConfig->compare_type))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicRldpCheckingStatePara(&pConfig->num_check, &pConfig->interval_check))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicRldpLoopStatePara(&pConfig->num_loop, &pConfig->interval_loop))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_rldp_portConfig_set
- * Description:
- *      Set per port RLDP module configuration
- * Input:
- *      port   - port number to be configured
- *      pPortConfig - per port configuration structure of RLDP
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rldp_portConfig_set(rtk_port_t port, rtk_rldp_portConfig_t *pPortConfig)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-    rtk_uint32 phy_port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (pPortConfig->tx_enable>= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    phy_port = rtk_switch_port_L2P_get(port);
-
-    if ((retVal = rtl8367c_getAsicRldpTxPortmask(&pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    if (pPortConfig->tx_enable)
-    {
-         pmsk |=(1<<phy_port);
-    }
-    else
-    {
-         pmsk &= ~(1<<phy_port);
-    }
-
-    if ((retVal = rtl8367c_setAsicRldpTxPortmask(pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-} /* end of rtk_rldp_portConfig_set */
-
-
-/* Function Name:
- *      rtk_rldp_portConfig_get
- * Description:
- *      Get per port RLDP module configuration
- * Input:
- *      port    - port number to be get
- * Output:
- *      pPortConfig - per port configuration structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rldp_portConfig_get(rtk_port_t port, rtk_rldp_portConfig_t *pPortConfig)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-    rtk_portmask_t logicalPmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicRldpTxPortmask(&pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmsk, &logicalPmask)) != RT_ERR_OK)
-        return retVal;
-
-
-    if (logicalPmask.bits[0] & (1<<port))
-    {
-         pPortConfig->tx_enable = ENABLED;
-    }
-    else
-    {
-         pPortConfig->tx_enable = DISABLED;
-    }
-
-    return RT_ERR_OK;
-} /* end of rtk_rldp_portConfig_get */
-
-
-/* Function Name:
- *      rtk_rldp_status_get
- * Description:
- *      Get RLDP module status
- * Input:
- *      None
- * Output:
- *      pStatus - status structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rldp_status_get(rtk_rldp_status_t *pStatus)
-{
-    rtk_api_ret_t retVal;
-    ether_addr_t seed;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_getAsicRldpRandomNumber(&seed))!=RT_ERR_OK)
-        return retVal;
-    memcpy(&pStatus->id, &seed, sizeof(ether_addr_t));
-
-    return RT_ERR_OK;
-} /* end of rtk_rldp_status_get */
-
-
-/* Function Name:
- *      rtk_rldp_portStatus_get
- * Description:
- *      Get RLDP module status
- * Input:
- *      port    - port number to be get
- * Output:
- *      pPortStatus - per port status structure of RLDP
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rldp_portStatus_get(rtk_port_t port, rtk_rldp_portStatus_t *pPortStatus)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-    rtk_portmask_t logicalPmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicRldpLoopedPortmask(&pmsk))!=RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtk_switch_portmask_P2L_get(pmsk, &logicalPmask)) != RT_ERR_OK)
-        return retVal;
-
-    if (logicalPmask.bits[0] & (1<<port))
-    {
-         pPortStatus->loop_status = RTK_RLDP_LOOPSTS_LOOPING;
-    }
-    else
-    {
-         pPortStatus->loop_status  = RTK_RLDP_LOOPSTS_NONE;
-    }
-
-    if ((retVal = rtl8367c_getAsicRldpEnterLoopedPortmask(&pmsk))!=RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtk_switch_portmask_P2L_get(pmsk, &logicalPmask)) != RT_ERR_OK)
-        return retVal;
-
-    if (logicalPmask.bits[0] & (1<<port))
-    {
-         pPortStatus->loop_enter = RTK_RLDP_LOOPSTS_LOOPING;
-    }
-    else
-    {
-         pPortStatus->loop_enter  = RTK_RLDP_LOOPSTS_NONE;
-    }
-
-    if ((retVal = rtl8367c_getAsicRldpLeaveLoopedPortmask(&pmsk))!=RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtk_switch_portmask_P2L_get(pmsk, &logicalPmask)) != RT_ERR_OK)
-        return retVal;
-
-    if (logicalPmask.bits[0] & (1<<port))
-    {
-         pPortStatus->loop_leave = RTK_RLDP_LOOPSTS_LOOPING;
-    }
-    else
-    {
-         pPortStatus->loop_leave  = RTK_RLDP_LOOPSTS_NONE;
-    }
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_rldp_portStatus_clear
- * Description:
- *      Clear RLDP module status
- * Input:
- *      port    - port number to be clear
- *      pPortStatus - per port status structure of RLDP
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      Clear operation effect loop_enter and loop_leave only, other field in
- *      the structure are don't care. Loop status cab't be clean.
- */
-rtk_api_ret_t rtk_rldp_portStatus_set(rtk_port_t port, rtk_rldp_portStatus_t *pPortStatus)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    pmsk = (pPortStatus->loop_enter)<<rtk_switch_port_L2P_get(port);
-    if ((retVal = rtl8367c_setAsicRldpEnterLoopedPortmask(pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    pmsk = (pPortStatus->loop_leave)<<rtk_switch_port_L2P_get(port);
-    if ((retVal = rtl8367c_setAsicRldpLeaveLoopedPortmask(pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rldp_portLoopPair_get
- * Description:
- *      Get RLDP port loop pairs
- * Input:
- *      port    - port number to be get
- * Output:
- *      pPortmask - per port related loop ports
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT
- *      RT_ERR_NULL_POINTER
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_rldp_portLoopPair_get(rtk_port_t port, rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicRldpLoopedPortPair(rtk_switch_port_L2P_get(port), &pmsk))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmsk, pPortmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtk_hal.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtk_hal.c
deleted file mode 100644
index b9373492cb..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtk_hal.c
+++ /dev/null
@@ -1,839 +0,0 @@
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include  "./include/rtk_switch.h"
-#include  "./include/vlan.h"
-#include  "./include/port.h"
-#include  "./include/rate.h"
-#include  "./include/rtk_hal.h"
-#include  "./include/l2.h"
-#include  "./include/stat.h"
-#include  "./include/igmp.h"
-#include  "./include/trap.h"
-#include  "./include/leaky.h"
-#include  "./include/mirror.h"
-#include  "./include/rtl8367c_asicdrv_port.h"
-#include  "./include/rtl8367c_asicdrv_mib.h"
-#include  "./include/smi.h"
-#include  "./include/qos.h"
-#include  "./include/trunk.h"
-
-void rtk_hal_switch_init(void)
-{
-	if(rtk_switch_init() != 0)
-        printk("rtk_switch_init failed\n");
-	mdelay(500);
-	/*vlan init */
-	if (rtk_vlan_init() != 0)
-        printk("rtk_vlan_init failed\n");
-}
-
-void rtk_hal_dump_full_mib(void)
-{
-	rtk_port_t port;
-	rtk_stat_counter_t Cntr;
-	rtk_stat_port_type_t cntr_idx;
-
-	for (port = UTP_PORT0; port < (UTP_PORT0 + 5); port++) {
-		printk("\nPort%d\n", port);
-		for (cntr_idx = STAT_IfInOctets; cntr_idx < STAT_PORT_CNTR_END; cntr_idx ++) {
-			rtk_stat_port_get(port, cntr_idx, &Cntr);
-			printk("%8llu ", Cntr);
-			if (((cntr_idx%10) == 9))
-				printk("\n");
-		}
-	}
-
-	for (port = EXT_PORT0; port < (EXT_PORT0 + 2); port++) {
-		printk("\nPort%d\n", port);
-		for (cntr_idx = STAT_IfInOctets; cntr_idx < STAT_PORT_CNTR_END; cntr_idx ++) {
-			rtk_stat_port_get(port, cntr_idx, &Cntr);
-			printk("%8llu ", Cntr);
-			if (((cntr_idx%10) == 9))
-				printk("\n");
-		}
-	}
-	rtk_stat_global_reset();
-}
-void rtk_dump_mib_type(rtk_stat_port_type_t cntr_idx)
-{
-	rtk_port_t port;
-	rtk_stat_counter_t Cntr;
-
-	for (port = UTP_PORT0; port < (UTP_PORT0 + 5); port++) {
-		rtk_stat_port_get(port, cntr_idx, &Cntr);
-		printk("%8llu", Cntr);
-	}
-	for (port = EXT_PORT0; port < (EXT_PORT0 + 2); port++) {
-		rtk_stat_port_get(port, cntr_idx, &Cntr);
-		printk("%8llu", Cntr);
-	}
-	printk("\n");
-}
-
-void rtk_hal_dump_mib(void)
-{
-
-	printk("==================%8s%8s%8s%8s%8s%8s%8s\n", "Port0", "Port1",
-	       "Port2", "Port3", "Port4", "Port16", "Port17");
-	/* Get TX Unicast Pkts */
-	printk("TX Unicast Pkts  :");
-	rtk_dump_mib_type(STAT_IfOutUcastPkts);
-	/* Get TX Multicast Pkts */
-	printk("TX Multicast Pkts:");
-	rtk_dump_mib_type(STAT_IfOutMulticastPkts);
-	/* Get TX BroadCast Pkts */
-	printk("TX BroadCast Pkts:");
-	rtk_dump_mib_type(STAT_IfOutBroadcastPkts);
-	/* Get TX Collisions */
-	/* Get TX Puase Frames */
-	printk("TX Pause Frames  :");
-	rtk_dump_mib_type(STAT_Dot3OutPauseFrames);
-	/* Get TX Drop Events */
-	/* Get RX Unicast Pkts */
-	printk("RX Unicast Pkts  :");
-	rtk_dump_mib_type(STAT_IfInUcastPkts);
-	/* Get RX Multicast Pkts */
-	printk("RX Multicast Pkts:");
-	rtk_dump_mib_type(STAT_IfInMulticastPkts);
-	/* Get RX Broadcast Pkts */
-	printk("RX Broadcast Pkts:");
-	rtk_dump_mib_type(STAT_IfInBroadcastPkts);
-	/* Get RX FCS Erros */
-	printk("RX FCS Errors    :");
-	rtk_dump_mib_type(STAT_Dot3StatsFCSErrors);
-	/* Get RX Undersize Pkts */
-	printk("RX Undersize Pkts:");
-	rtk_dump_mib_type(STAT_EtherStatsUnderSizePkts);
-	/* Get RX Discard Pkts */
-	printk("RX Discard Pkts  :");
-	rtk_dump_mib_type(STAT_Dot1dTpPortInDiscards);
-	/* Get RX Fragments */
-	printk("RX Fragments     :");
-	rtk_dump_mib_type(STAT_EtherStatsFragments);
-	/* Get RX Oversize Pkts */
-	printk("RX Oversize Pkts :");
-	rtk_dump_mib_type(STAT_EtherOversizeStats);
-	/* Get RX Jabbers */
-	printk("RX Jabbers       :");
-	rtk_dump_mib_type(STAT_EtherStatsJabbers);
-	/* Get RX Pause Frames */
-	printk("RX Pause Frames  :");
-	rtk_dump_mib_type(STAT_Dot3InPauseFrames);
-	/* clear MIB */
-	rtk_stat_global_reset();
-}
-EXPORT_SYMBOL(rtk_hal_dump_mib);
-
-int rtk_hal_dump_vlan(void)
-{
-	rtk_vlan_cfg_t vlan;
-	int i;
-
-	printk("vid    portmap\n");
-	for (i = 0; i < RTK_SW_VID_RANGE; i++) {
-		rtk_vlan_get(i, &vlan);
-		printk("%3d    ", i);
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-						UTP_PORT0) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-						UTP_PORT1) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-						UTP_PORT2) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-						UTP_PORT3) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-						UTP_PORT4) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-						EXT_PORT0) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-						EXT_PORT1) ? '1' : '-');
-		printk("\n");
-	}
-	return 0;
-}
-
-void rtk_hal_clear_vlan(void)
-{
-	rtk_api_ret_t ret;
-
-	ret =  rtk_vlan_reset();
-    if (ret != RT_ERR_OK)
-        printk("rtk_vlan_reset failed\n");
-}
-
-int rtk_hal_set_vlan(struct ra_switch_ioctl_data *data)
-{
-	rtk_vlan_cfg_t vlan;
-	rtk_api_ret_t ret;
-	int i;
-
-	/* clear vlan entry first */
-	memset(&vlan, 0x00, sizeof(rtk_vlan_cfg_t));
-	RTK_PORTMASK_CLEAR(vlan.mbr);
-	RTK_PORTMASK_CLEAR(vlan.untag);
-	rtk_vlan_set(data->vid, &vlan);
-
-	memset(&vlan, 0x00, sizeof(rtk_vlan_cfg_t));
-	for (i = 0; i < 5; i++) {
-		if (data->port_map & (1 << i)) {
-			RTK_PORTMASK_PORT_SET(vlan.mbr, i);
-			RTK_PORTMASK_PORT_SET(vlan.untag, i);
-			rtk_vlan_portPvid_set(i, data->vid, 0);
-		}
-	}
-	for (i = 0; i < 2; i++) {
-		if (data->port_map & (1 << (i + 5))) {
-			RTK_PORTMASK_PORT_SET(vlan.mbr, (i + EXT_PORT0));
-			RTK_PORTMASK_PORT_SET(vlan.untag, (i + EXT_PORT0));
-			rtk_vlan_portPvid_set((i + EXT_PORT0), data->vid, 0);
-		}
-	}
-	vlan.ivl_en = 1;
-	ret = rtk_vlan_set(data->vid, &vlan);
-
-	return 0;
-}
-
-void rtk_hal_vlan_portpvid_set(rtk_port_t port, rtk_vlan_t pvid, rtk_pri_t priority)
-{
-	rtk_vlan_portPvid_set(port, pvid, priority);
-}
-
-int rtk_hal_set_ingress_rate(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-
-	if (data->on_off == 1)
-		ret =
-		    rtk_rate_igrBandwidthCtrlRate_set(data->port, data->bw, 0,
-						      1);
-	else
-		ret =
-		    rtk_rate_igrBandwidthCtrlRate_set(data->port, 1048568, 0,
-						      1);
-
-	return ret;
-}
-
-int rtk_hal_set_egress_rate(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-
-	if (data->on_off == 1)
-		ret =
-		    rtk_rate_egrBandwidthCtrlRate_set(data->port, data->bw, 1);
-	else
-		ret = rtk_rate_egrBandwidthCtrlRate_set(data->port, 1048568, 1);
-
-	return ret;
-}
-
-void rtk_hal_dump_table(void)
-{
-	rtk_uint32 i;
-	rtk_uint32 address = 0;
-	rtk_l2_ucastAddr_t l2_data;
-	rtk_l2_ipMcastAddr_t ipMcastAddr;
-
-	printk("hash  port(0:17)   fid   vid  mac-address\n");
-	while (1) {
-		if (rtk_l2_addr_next_get(READMETHOD_NEXT_L2UC, UTP_PORT0, &address, &l2_data) != RT_ERR_OK) {
-			break;
-		} else {
-			printk("%03x   ", l2_data.address);
-			for (i = 0; i < 5; i++)
-				if ( l2_data.port == i)
-					printk("1");
-				else
-					printk("-");
-			for (i = 16; i < 18; i++)
-				if ( l2_data.port == i)
-					printk("1");
-				else
-					printk("-");
-
-			printk("      %2d", l2_data.fid);
-			printk("  %4d", l2_data.cvid);
-			printk("  %02x%02x%02x%02x%02x%02x\n", l2_data.mac.octet[0],
-			l2_data.mac.octet[1], l2_data.mac.octet[2], l2_data.mac.octet[3], 
-			l2_data.mac.octet[4], l2_data.mac.octet[5]);
-			address ++;
-			}
-	}
-
-	address = 0;
-	while (1) {
-        if (rtk_l2_ipMcastAddr_next_get(&address, &ipMcastAddr) != RT_ERR_OK) {
-            break;
-        } else {
-            printk("%03x   ", ipMcastAddr.address);
-            for (i = 0; i < 5; i++)
-                printk("%c", RTK_PORTMASK_IS_PORT_SET(ipMcastAddr.portmask, i) ? '1' : '-');
-            for (i = 16; i < 18; i++)
-                printk("%c", RTK_PORTMASK_IS_PORT_SET(ipMcastAddr.portmask, i) ? '1' : '-');
-			printk("                ");
-			printk("01005E%06x\n", (ipMcastAddr.dip & 0xefffff));
-            address ++;
-            }
-    }
-}
-
-void rtk_hal_clear_table(void)
-{
-	rtk_api_ret_t ret;
-
-	ret = rtk_l2_table_clear();
-	if (ret != RT_ERR_OK)
-		printk("rtk_l2_table_clear failed\n");
-}
-
-void rtk_hal_add_table(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_l2_ucastAddr_t l2_entry;
-	rtk_mac_t mac;
-
-	mac.octet[0] =data->mac[0];
-	mac.octet[1] =data->mac[1];
-	mac.octet[2] =data->mac[2];
-	mac.octet[3] =data->mac[3];
-	mac.octet[4] =data->mac[4];
-	mac.octet[5] =data->mac[5];
-
-	memset(&l2_entry, 0x00, sizeof(rtk_l2_ucastAddr_t));
-	l2_entry.port = data->port;
-	l2_entry.ivl = 1;
-	l2_entry.cvid = data->vid;
-	l2_entry.fid = 0;
-	l2_entry.efid = 0;
-	l2_entry.is_static = 1;
-	ret = rtk_l2_addr_add(&mac, &l2_entry);
-	if (ret != RT_ERR_OK)
-		printk("rtk_hal_add_table failed\n");
-}
-
-void rtk_hal_del_table(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_l2_ucastAddr_t l2_entry;
-	rtk_mac_t mac;
-
-	mac.octet[0] =data->mac[0];
-	mac.octet[1] =data->mac[1];
-	mac.octet[2] =data->mac[2];
-	mac.octet[3] =data->mac[3];
-	mac.octet[4] =data->mac[4];
-	mac.octet[5] =data->mac[5];
-
-	memset(&l2_entry, 0x00, sizeof(rtk_l2_ucastAddr_t));
-	l2_entry.port = data->port;
-	l2_entry.ivl = 1;
-	l2_entry.cvid = data->vid;
-	l2_entry.fid = 0;
-	l2_entry.efid = 0;
-	ret = rtk_l2_addr_del(&mac, &l2_entry);
-	if (ret != RT_ERR_OK)
-		printk("rtk_hal_add_table failed\n");
-}
-void rtk_hal_get_phy_status(struct ra_switch_ioctl_data *data)
-{
-	rtk_port_linkStatus_t linkStatus;
-	rtk_port_speed_t speed;
-	rtk_port_duplex_t duplex;
-
-    rtk_port_phyStatus_get(data->port, &linkStatus, &speed, &duplex);
-    printk("Port%d Status:\n", data->port);
-	if (linkStatus == 1) {
-        printk("Link Up");
-        if (speed == 0)
-			printk(" 10M");
-		else if (speed == 1)
-			printk(" 100M");
-		else if (speed == 2)
-            printk(" 1000M");
-        if (duplex == 0)
-			printk(" Half Duplex\n");
-		else
-			printk(" Full Duplex\n");
-	} else
-		printk("Link Down\n");
-
-}
-
-void rtk_hal_set_port_mirror(struct ra_switch_ioctl_data *data)
-{
-	rtk_portmask_t rx_portmask;
-	rtk_portmask_t tx_portmask;
-	rtk_api_ret_t ret;
-	int i;
-
-	rtk_mirror_portIso_set(ENABLED);
-	RTK_PORTMASK_CLEAR(rx_portmask);
-	RTK_PORTMASK_CLEAR(tx_portmask);
-    for (i = 0; i < 5; i++)
-		if (data->rx_port_map & (1 << i))
-			RTK_PORTMASK_PORT_SET(rx_portmask, i);
-	for (i = 0; i < 2; i++)
-		if (data->rx_port_map & (1 << (i + 5)))
-			RTK_PORTMASK_PORT_SET(rx_portmask, (i + EXT_PORT0));
-
-	RTK_PORTMASK_CLEAR(tx_portmask);
-    for (i = 0; i < 5; i++)
-        if (data->tx_port_map & (1 << i))
-            RTK_PORTMASK_PORT_SET(tx_portmask, i);
-    for (i = 0; i < 2; i++)
-        if (data->tx_port_map & (1 << (i + 5)))
-            RTK_PORTMASK_PORT_SET(tx_portmask, (i + EXT_PORT0));
-
-    ret = rtk_mirror_portBased_set(data->port, &rx_portmask, &tx_portmask);
-	if (!ret)
-		printk("rtk_mirror_portBased_set success\n");
-}
-
-void rtk_hal_read_reg(struct ra_switch_ioctl_data *data)
-{
-	ret_t retVal;
-
-	retVal = smi_read(data->reg_addr, &data->reg_val);
-	if(retVal != RT_ERR_OK)
-		printk("switch reg read failed\n");
-	else
-		printk("reg0x%x = 0x%x\n", data->reg_addr, data->reg_val);
-}
-
-void rtk_hal_write_reg(struct ra_switch_ioctl_data *data)
-{
-	ret_t retVal;
-
-    retVal = smi_write(data->reg_addr, data->reg_val);
-    if(retVal != RT_ERR_OK)
-        printk("switch reg write failed\n");
-    else
-        printk("write switch reg0x%x 0x%x success\n", data->reg_addr, data->reg_val);
-}
-
-void rtk_hal_get_phy_reg(struct ra_switch_ioctl_data *data)
-{
-	ret_t retVal;
-	rtk_port_phy_data_t Data;
-
-	retVal = rtk_port_phyReg_get(data->port, data->reg_addr, &Data);
-	if (retVal == RT_ERR_OK)
-		printk("Get: phy[%d].reg[%d] = 0x%04x\n", data->port, data->reg_addr, Data);
-	else
-		printk("read phy reg failed\n");
-}
-
-void rtk_hal_set_phy_reg(struct ra_switch_ioctl_data *data)
-{
-	ret_t retVal;
-
-	retVal = rtk_port_phyReg_set(data->port, data->reg_addr, data->reg_val);
-	if (retVal == RT_ERR_OK)
-		printk("Set: phy[%d].reg[%d] = 0x%04x\n", data->port, data->reg_addr, data->reg_val);
-	else
-		printk("write phy reg failed\n");
-}
-void rtk_hal_qos_en(struct ra_switch_ioctl_data *data)
-{
-
-	if (data->on_off == 1) {
-		if (rtk_qos_init(8) != 0)
-			printk("rtk_qos_init(8) failed\n");
-	}
-	else {
-		if (rtk_qos_init(1) != 0)
-            printk("rtk_qos_init(1) failed\n");
-	}
-}
-
-void rtk_hal_qos_set_table2type(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_priority_select_t PriDec;
-
-	/* write all pri to 0 */
-	PriDec.port_pri = 0;
-    PriDec.dot1q_pri = 0;
-    PriDec.acl_pri = 0;
-    PriDec.cvlan_pri = 0;
-    PriDec.svlan_pri = 0;
-    PriDec.dscp_pri = 0;
-    PriDec.dmac_pri = 0;
-    PriDec.smac_pri = 0;
-
-	if (data->qos_type == 0)
-		PriDec.port_pri = 1;
-	else if (data->qos_type == 1)
-		PriDec.dot1q_pri = 1;
-	else if (data->qos_type == 2)
-		PriDec.acl_pri = 1;
-	else if (data->qos_type == 3)
-		PriDec.dscp_pri = 1;
-	else if (data->qos_type == 4)
-		PriDec.cvlan_pri = 1;
-	else if (data->qos_type == 5)
-		PriDec.svlan_pri = 1;
-	else if (data->qos_type == 6)
-		PriDec.dmac_pri = 1;
-	else if (data->qos_type == 7)
-		PriDec.smac_pri = 1;
-
-	if (data->qos_table_idx == 0)
-		ret = rtk_qos_priSel_set(PRIDECTBL_IDX0, &PriDec);
-	else
-		ret = rtk_qos_priSel_set(PRIDECTBL_IDX1, &PriDec);
-
-	if (ret != 0)
-		printk("rtk_qos_priSel_set failed\n");
-
-}
-
-void rtk_hal_qos_get_table2type(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_priority_select_t PriDec;
-
-	if (data->qos_table_idx == 0)
-        ret = rtk_qos_priSel_get(PRIDECTBL_IDX0, &PriDec);
-    else
-        ret = rtk_qos_priSel_get(PRIDECTBL_IDX1, &PriDec);
-
-	if (ret != 0)
-        printk("rtk_qos_priSel_set failed\n");
-    else {
-		printk("port_pri  = %d\n", PriDec.port_pri);
-		printk("dot1q_pri = %d\n", PriDec.dot1q_pri);
-		printk("acl_pri   = %d\n", PriDec.acl_pri);
-		printk("dscp_pri  = %d\n", PriDec.dscp_pri);
-		printk("cvlan_pri = %d\n", PriDec.cvlan_pri);
-		printk("svlan_pri = %d\n", PriDec.svlan_pri);
-		printk("dmac_pri  = %d\n", PriDec.dmac_pri);
-		printk("smac_pri  = %d\n", PriDec.smac_pri);
-	}
-}
-
-void rtk_hal_qos_set_port2table(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	
-	ret = rtk_qos_portPriSelIndex_set(data->port, data->qos_table_idx);
-	if (ret != 0)
-		printk("rtk_qos_portPriSelIndex_set failed\n");
-}
-
-void rtk_hal_qos_get_port2table(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_qos_priDecTbl_t Index;
-	
-	ret = rtk_qos_portPriSelIndex_get(data->port, &Index);
-	if (ret != 0)
-		printk("rtk_qos_portPriSelIndex_set failed\n");
-	else
-		printk("port%d belongs to table%d\n", data->port, Index);
-}
-
-void rtk_hal_qos_set_port2pri(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-
-	ret = rtk_qos_portPri_set(data->port, data->qos_pri);
-	if (ret != 0)
-		printk("rtk_qos_portPri_set failed\n");
-}
-
-void rtk_hal_qos_get_port2pri(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_pri_t Int_pri;
-
-	ret = rtk_qos_portPri_get(data->port, &Int_pri);
-	if (ret != 0)
-		printk("rtk_qos_portPri_set failed\n");
-	else
-		printk("port%d priority = %d\n", data->port, Int_pri);
-}
-
-void rtk_hal_qos_set_dscp2pri(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-
-	ret = rtk_qos_dscpPriRemap_set(data->qos_dscp, data->qos_pri);
-	if (ret != 0)
-		printk("rtk_qos_dscpPriRemap_set failed\n");
-}
-
-void rtk_hal_qos_get_dscp2pri(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_pri_t Int_pri;
-
-	ret = rtk_qos_dscpPriRemap_get(data->qos_dscp, &Int_pri);
-	if (ret != 0)
-		printk("rtk_qos_dscpPriRemap_set failed\n");
-	else
-		printk("dscp%d priority is %d\n", data->qos_dscp, Int_pri);
-}
-
-void rtk_hal_qos_set_pri2queue(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_qos_pri2queue_t pri2qid;
-
-	ret = rtk_qos_priMap_get(8, &pri2qid);
-	pri2qid.pri2queue[data->qos_queue_num] = data->qos_pri;
-	ret = rtk_qos_priMap_set(8, &pri2qid);
-	if (ret != 0)
-		printk("rtk_qos_priMap_set failed\n");
-}
-
-void rtk_hal_qos_get_pri2queue(struct ra_switch_ioctl_data *data)
-{
-	int i;
-	rtk_api_ret_t ret;
-	rtk_qos_pri2queue_t pri2qid;
-
-	ret = rtk_qos_priMap_get(8, &pri2qid);
-	if (ret != 0)
-		printk("rtk_qos_priMap_get failed\n");
-	else {
-		for (i = 0; i < 8; i++)
-			printk("pri2qid.pri2queue[%d] = %d\n", i, pri2qid.pri2queue[i]);
-	}
-}
-
-void rtk_hal_qos_set_queue_weight(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_qos_queue_weights_t qweights;
-
-	ret = rtk_qos_schedulingQueue_get(data->port, &qweights);
-	qweights.weights[data->qos_queue_num] = data->qos_weight;
-	ret = rtk_qos_schedulingQueue_set(data->port, &qweights);
-	if (ret != 0)
-		printk("rtk_qos_schedulingQueue_set failed\n");
-}
-
-void rtk_hal_qos_get_queue_weight(struct ra_switch_ioctl_data *data)
-{
-	int i;
-	rtk_api_ret_t ret;
-	rtk_qos_queue_weights_t qweights;
-
-	ret = rtk_qos_schedulingQueue_get(data->port, &qweights);
-	if (ret != 0)
-		printk("rtk_qos_schedulingQueue_get failed\n");
-	else {
-		printk("=== Port%d queue weight ===\n", data->port);
-		for (i = 0; i < 8; i++)
-			printk("qweights.weights[%d] = %d\n",i ,qweights.weights[i]);
-	}
-}
-
-void rtk_hal_enable_igmpsnoop(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_portmask_t pmask;
-	
-
-	ret = rtk_igmp_init();
-	if (data->on_off == 1) {
-		RTK_PORTMASK_CLEAR(pmask);
-		RTK_PORTMASK_PORT_SET(pmask, EXT_PORT0);
-		ret |= rtk_igmp_static_router_port_set(&pmask);
-		ret |= rtk_igmp_protocol_set(UTP_PORT4, PROTOCOL_IGMPv1, IGMP_ACTION_FORWARD);
-		ret |= rtk_igmp_protocol_set(UTP_PORT4, PROTOCOL_IGMPv2, IGMP_ACTION_FORWARD);
-		ret |= rtk_igmp_protocol_set(UTP_PORT4, PROTOCOL_MLDv1, IGMP_ACTION_FORWARD);
-		ret |= rtk_igmp_protocol_set(EXT_PORT1, PROTOCOL_IGMPv1, IGMP_ACTION_FORWARD);
-		ret |= rtk_igmp_protocol_set(EXT_PORT1, PROTOCOL_IGMPv2, IGMP_ACTION_FORWARD);
-		ret |= rtk_igmp_protocol_set(EXT_PORT1, PROTOCOL_MLDv1, IGMP_ACTION_FORWARD);
-		ret |= rtk_igmp_protocol_set(UTP_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(UTP_PORT1, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(UTP_PORT2, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(UTP_PORT3, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(EXT_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-
-		ret |= rtk_leaky_vlan_set(LEAKY_IPMULTICAST, ENABLED);
-		ret |= rtk_l2_ipMcastForwardRouterPort_set(DISABLED);
-		/* drop unknown multicast packets*/
-		/* ret |= rtk_trap_unknownMcastPktAction_set(UTP_PORT4, MCAST_IPV4, MCAST_ACTION_DROP);*/
-	} else {
-		RTK_PORTMASK_CLEAR(pmask);
-        RTK_PORTMASK_PORT_SET(pmask, EXT_PORT0);
-        RTK_PORTMASK_PORT_SET(pmask, EXT_PORT1);
-		ret |= rtk_igmp_protocol_set(UTP_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(UTP_PORT1, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(UTP_PORT2, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(UTP_PORT3, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-		ret |= rtk_igmp_protocol_set(EXT_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-
-		ret |= rtk_igmp_static_router_port_set(&pmask);
-	}
-	if(ret != RT_ERR_OK)
-		printk("enable switch igmpsnoop failed\n");
-}
-
-void rtk_hal_disable_igmpsnoop(void)
-{
-	if (rtk_igmp_state_set(DISABLED) != RT_ERR_OK)
-		printk("Disable IGMP SNOOPING failed\n");
-}
-
-rtk_api_ret_t rtk_port_phyTestMode_set(rtk_port_t port, rtk_port_phy_test_mode_t mode)
-{
-    rtk_uint32          data, regData, i;
-    rtk_api_ret_t       retVal;
-
-    RTK_CHK_PORT_IS_UTP(port);
-
-    if(mode >= PHY_TEST_MODE_END)
-        return RT_ERR_INPUT;
-
-    if( (mode == PHY_TEST_MODE_2) || (mode == PHY_TEST_MODE_3) )
-        return RT_ERR_INPUT;
-
-    if (PHY_TEST_MODE_NORMAL != mode)
-    {
-        /* Other port should be Normal mode */
-        RTK_SCAN_ALL_LOG_PORT(i)
-        {
-            if(rtk_switch_isUtpPort(i) == RT_ERR_OK)
-            {
-                if(i != port)
-                {
-                    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(i), 9, &data)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((data & 0xE000) != 0)
-                        return RT_ERR_NOT_ALLOWED;
-                }
-            }
-        }
-    }
-
-    if ((retVal = rtl8367c_getAsicPHYReg(rtk_switch_port_L2P_get(port), 9, &data)) != RT_ERR_OK)
-        return retVal;
-
-    data &= ~0xE000;
-    data |= (mode << 13);
-    if ((retVal = rtl8367c_setAsicPHYReg(rtk_switch_port_L2P_get(port), 9, data)) != RT_ERR_OK)
-        return retVal;
-
-    if (PHY_TEST_MODE_4 == mode)
-    {
-        if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-            return retVal;
-
-        if((retVal = rtl8367c_getAsicReg(0x1300, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        if( (regData == 0x0276) || (regData == 0x0597) )
-        {
-            if ((retVal = rtl8367c_setAsicPHYOCPReg(rtk_switch_port_L2P_get(port), 0xbcc2, 0xF4F4)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        if( (regData == 0x6367) )
-        {
-            if ((retVal = rtl8367c_setAsicPHYOCPReg(rtk_switch_port_L2P_get(port), 0xa436, 0x80c1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicPHYOCPReg(rtk_switch_port_L2P_get(port), 0xa438, 0xfe00)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-void rtk_hal_set_phy_test_mode(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-
-    ret = rtk_port_phyTestMode_set(data->port, data->mode);
-	if (ret != RT_ERR_OK)
-		printk("rtk_port_phyTestMode_set failed\n");
-	else
-		printk("set port%d in test mode %d.\n", data->port, data->mode);
-}
-
-void rtk_hal_set_port_trunk(struct ra_switch_ioctl_data *data)
-{
-
-	rtk_api_ret_t ret;
-	rtk_portmask_t member;
-	int i;
-
-	RTK_PORTMASK_CLEAR(member);
-	for (i = 0; i < 4; i++) {
-		if (data->port_map & (1 << i))
-			RTK_PORTMASK_PORT_SET(member, i);
-    }
-
-	ret = rtk_trunk_port_set(TRUNK_GROUP0, &member);
-	if (ret != RT_ERR_OK)
-		printk("rtk_trunk_port_set failed\n");
-
-	ret = rtk_trunk_distributionAlgorithm_set(RTK_WHOLE_SYSTEM, 0x7F);
-	if (ret != RT_ERR_OK)
-		printk("rtk_trunk_distributionAlgorithm_set failed\n");
-}
-
-void rtk_hal_vlan_tag(struct ra_switch_ioctl_data *data)
-{
-	rtk_api_ret_t ret;
-	rtk_vlan_cfg_t vlan;
-
-    ret = rtk_vlan_get(data->vid, &vlan);
-	if (ret != RT_ERR_OK)
-		printk("rtk_vlan_get failed\n");
-	else {
-		if (data->on_off == 0)
-			RTK_PORTMASK_PORT_SET(vlan.untag, data->port);
-		else
-			RTK_PORTMASK_PORT_CLEAR(vlan.untag, data->port);
-		
-		ret = rtk_vlan_set(data->vid, &vlan);
-		if (ret != RT_ERR_OK)
-			printk("rtk_vlan_set failed\n");
-	}
-}
-
-void rtk_hal_vlan_mode(struct ra_switch_ioctl_data *data)
-{
-	rtk_vlan_cfg_t vlan1, vlan2;
-	rtk_api_ret_t ret;
-
-	ret = rtk_vlan_get(1, &vlan1);
-	if (ret != RT_ERR_OK)
-		printk("rtk_vlan_get failed\n");
-
-	ret = rtk_vlan_get(2, &vlan2);
-	if (ret != RT_ERR_OK)
-		printk("rtk_vlan_get failed\n");
-
-	if (data->mode == 0) { //ivl
-		vlan1.ivl_en = 1;
-		vlan1.fid_msti = 0;
-		rtk_vlan_set(1, &vlan1);
-		vlan2.ivl_en = 1;
-		vlan2.fid_msti = 0;
-		rtk_vlan_set(2, &vlan2);
-	} else if(data->mode == 1) {//svl
-		vlan1.ivl_en = 0;
-		vlan1.fid_msti = 0;
-		rtk_vlan_set(1, &vlan1);
-		vlan2.ivl_en = 0;
-		vlan2.fid_msti = 1;
-		rtk_vlan_set(2, &vlan2);
-	} else
-		printk("mode not supported\n");
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtk_switch.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtk_switch.c
deleted file mode 100644
index 0bb0db0776..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtk_switch.c
+++ /dev/null
@@ -1,1796 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76336 $
- * $Date: 2017-03-09 10:41:21 +0800 (週四, 09 三月 2017) $
- *
- * Purpose : RTK switch high-level API
- * Feature : Here is a list of all functions and variables in this module.
- *
- */
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <string.h>
-
-#include <rate.h>
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_misc.h>
-#include <rtl8367c_asicdrv_green.h>
-#include <rtl8367c_asicdrv_lut.h>
-#include <rtl8367c_asicdrv_rma.h>
-#include <rtl8367c_asicdrv_mirror.h>
-
-#if defined(FORCE_PROBE_RTL8367C)
-static init_state_t    init_state = INIT_COMPLETED;
-#elif defined(FORCE_PROBE_RTL8370B)
-static init_state_t    init_state = INIT_COMPLETED;
-#elif defined(FORCE_PROBE_RTL8364B)
-static init_state_t    init_state = INIT_COMPLETED;
-#elif defined(FORCE_PROBE_RTL8363SC_VB)
-static init_state_t    init_state = INIT_COMPLETED;
-#else
-static init_state_t    init_state = INIT_NOT_COMPLETED;
-#endif
-
-#define AUTO_PROBE (!defined(FORCE_PROBE_RTL8367C) && !defined(FORCE_PROBE_RTL8370B) && !defined(FORCE_PROBE_RTL8364B) && !defined(FORCE_PROBE_RTL8363SC_VB))
-
-#if (AUTO_PROBE || defined(FORCE_PROBE_RTL8367C))
-static rtk_switch_halCtrl_t rtl8367c_hal_Ctrl =
-{
-    /* Switch Chip */
-    CHIP_RTL8367C,
-
-    /* Logical to Physical */
-    {0, 1, 2, 3, 4, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
-     6, 7, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF },
-
-    /* Physical to Logical */
-    {UTP_PORT0, UTP_PORT1, UTP_PORT2, UTP_PORT3, UTP_PORT4, UNDEFINE_PORT, EXT_PORT0, EXT_PORT1,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT},
-
-    /* Port Type */
-    {UTP_PORT, UTP_PORT, UTP_PORT, UTP_PORT, UTP_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     EXT_PORT, EXT_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT},
-
-    /* PTP port */
-    {1, 1, 1, 1, 1, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0 },
-
-    /* Valid port mask */
-    ( (0x1 << UTP_PORT0) | (0x1 << UTP_PORT1) | (0x1 << UTP_PORT2) | (0x1 << UTP_PORT3) | (0x1 << UTP_PORT4) | (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Valid UTP port mask */
-    ( (0x1 << UTP_PORT0) | (0x1 << UTP_PORT1) | (0x1 << UTP_PORT2) | (0x1 << UTP_PORT3) | (0x1 << UTP_PORT4) ),
-
-    /* Valid EXT port mask */
-    ( (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Valid CPU port mask */
-    0x00,
-
-    /* Minimum physical port number */
-    0,
-
-    /* Maxmum physical port number */
-    7,
-
-    /* Physical port mask */
-    0xDF,
-
-    /* Combo Logical port ID */
-    4,
-
-    /* HSG Logical port ID */
-    EXT_PORT0,
-
-    /* SGMII Logical portmask */
-    (0x1 << EXT_PORT0),
-
-    /* Max Meter ID */
-    31,
-
-    /* MAX LUT Address Number */
-    2112,
-
-    /* Trunk Group Mask */
-    0x03
-};
-#endif
-
-#if (AUTO_PROBE || defined(FORCE_PROBE_RTL8370B))
-static rtk_switch_halCtrl_t rtl8370b_hal_Ctrl =
-{
-    /* Switch Chip */
-    CHIP_RTL8370B,
-
-    /* Logical to Physical */
-    {0, 1, 2, 3, 4, 5, 6, 7, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
-     8, 9, 10, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF },
-
-    /* Physical to Logical */
-    {UTP_PORT0, UTP_PORT1, UTP_PORT2, UTP_PORT3, UTP_PORT4, UTP_PORT5, UTP_PORT6, UTP_PORT7,
-     EXT_PORT0, EXT_PORT1, EXT_PORT2, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT},
-
-    /* Port Type */
-    {UTP_PORT, UTP_PORT, UTP_PORT, UTP_PORT, UTP_PORT, UTP_PORT, UTP_PORT, UTP_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     EXT_PORT, EXT_PORT, EXT_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT},
-
-    /* PTP port */
-    {1, 1, 1, 1, 1, 1, 1, 1,
-     0, 0, 0, 0, 0, 0, 0, 0,
-     1, 1, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0 },
-
-    /* Valid port mask */
-    ( (0x1 << UTP_PORT0) | (0x1 << UTP_PORT1) | (0x1 << UTP_PORT2) | (0x1 << UTP_PORT3) | (0x1 << UTP_PORT4) | (0x1 << UTP_PORT5) | (0x1 << UTP_PORT6) | (0x1 << UTP_PORT7) | (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) | (0x1 << EXT_PORT2) ),
-
-    /* Valid UTP port mask */
-    ( (0x1 << UTP_PORT0) | (0x1 << UTP_PORT1) | (0x1 << UTP_PORT2) | (0x1 << UTP_PORT3) | (0x1 << UTP_PORT4) | (0x1 << UTP_PORT5) | (0x1 << UTP_PORT6) | (0x1 << UTP_PORT7) ),
-
-    /* Valid EXT port mask */
-    ( (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) | (0x1 << EXT_PORT2) ),
-
-    /* Valid CPU port mask */
-    (0x1 << EXT_PORT2),
-
-    /* Minimum physical port number */
-    0,
-
-    /* Maxmum physical port number */
-    10,
-
-    /* Physical port mask */
-    0x7FF,
-
-    /* Combo Logical port ID */
-    7,
-
-    /* HSG Logical port ID */
-    EXT_PORT1,
-
-    /* SGMII Logical portmask */
-    ( (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Max Meter ID */
-    63,
-
-    /* MAX LUT Address Number 4096 + 64*/
-    4160,
-
-    /* Trunk Group Mask */
-    0x07
-};
-#endif
-
-#if (AUTO_PROBE || defined(FORCE_PROBE_RTL8364B))
-static rtk_switch_halCtrl_t rtl8364b_hal_Ctrl =
-{
-    /* Switch Chip */
-    CHIP_RTL8364B,
-
-    /* Logical to Physical */
-    {0xFF, 1, 0xFF, 3, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
-     6, 7, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF },
-
-    /* Physical to Logical */
-    {UNDEFINE_PORT, UTP_PORT1, UNDEFINE_PORT, UTP_PORT3, UNDEFINE_PORT, UNDEFINE_PORT, EXT_PORT0, EXT_PORT1,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT},
-
-    /* Port Type */
-    {UNKNOWN_PORT, UTP_PORT, UNKNOWN_PORT, UTP_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     EXT_PORT, EXT_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT},
-
-    /* PTP port */
-    {0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0 },
-
-    /* Valid port mask */
-    ( (0x1 << UTP_PORT1) | (0x1 << UTP_PORT3) | (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Valid UTP port mask */
-    ( (0x1 << UTP_PORT1) | (0x1 << UTP_PORT3) ),
-
-    /* Valid EXT port mask */
-    ( (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Valid CPU port mask */
-    0x00,
-
-    /* Minimum physical port number */
-    0,
-
-    /* Maxmum physical port number */
-    7,
-
-    /* Physical port mask */
-    0xCA,
-
-    /* Combo Logical port ID */
-    4,
-
-    /* HSG Logical port ID */
-    EXT_PORT0,
-
-    /* SGMII Logical portmask */
-    ( (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Max Meter ID */
-    32,
-
-    /* MAX LUT Address Number */
-    2112,
-
-    /* Trunk Group Mask */
-    0x01
-};
-#endif
-
-#if (AUTO_PROBE || defined(FORCE_PROBE_RTL8363SC_VB))
-static rtk_switch_halCtrl_t rtl8363sc_vb_hal_Ctrl =
-{
-    /* Switch Chip */
-    CHIP_RTL8363SC_VB,
-
-    /* Logical to Physical */
-    {0xFF, 0xFF, 1, 3, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
-     6, 7, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF },
-
-    /* Physical to Logical */
-    {UNDEFINE_PORT, UTP_PORT2, UNDEFINE_PORT, UTP_PORT3, UNDEFINE_PORT, UNDEFINE_PORT, EXT_PORT0, EXT_PORT1,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT,
-     UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT, UNDEFINE_PORT},
-
-    /* Port Type */
-    {UNKNOWN_PORT, UNKNOWN_PORT, UTP_PORT, UTP_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     EXT_PORT, EXT_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT,
-     UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT, UNKNOWN_PORT},
-
-    /* PTP port */
-    {0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0,
-     0, 0, 0, 0, 0, 0, 0, 0 },
-
-    /* Valid port mask */
-    ( (0x1 << UTP_PORT2) | (0x1 << UTP_PORT3) | (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Valid UTP port mask */
-    ( (0x1 << UTP_PORT2) | (0x1 << UTP_PORT3) ),
-
-    /* Valid EXT port mask */
-    ( (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Valid CPU port mask */
-    0x00,
-
-    /* Minimum physical port number */
-    0,
-
-    /* Maxmum physical port number */
-    7,
-
-    /* Physical port mask */
-    0xCA,
-
-    /* Combo Logical port ID */
-    4,
-
-    /* HSG Logical port ID */
-    EXT_PORT0,
-
-    /* SGMII Logical portmask */
-    ( (0x1 << EXT_PORT0) | (0x1 << EXT_PORT1) ),
-
-    /* Max Meter ID */
-    32,
-
-    /* MAX LUT Address Number */
-    2112,
-
-    /* Trunk Group Mask */
-    0x01
-};
-#endif
-
-#if defined(FORCE_PROBE_RTL8367C)
-static rtk_switch_halCtrl_t *halCtrl = &rtl8367c_hal_Ctrl;
-#elif defined(FORCE_PROBE_RTL8370B)
-static rtk_switch_halCtrl_t *halCtrl = &rtl8370b_hal_Ctrl;
-#elif defined(FORCE_PROBE_RTL8364B)
-static rtk_switch_halCtrl_t *halCtrl = &rtl8364b_hal_Ctrl;
-#elif defined(FORCE_PROBE_RTL8363SC_VB)
-static rtk_switch_halCtrl_t *halCtrl = &rtl8363sc_vb_hal_Ctrl;
-#else
-static rtk_switch_halCtrl_t *halCtrl = NULL;
-#endif
-
-static rtk_uint32 PatchChipData[210][2] =
-{
-        {0xa436, 0x8028}, {0xa438, 0x6800}, {0xb82e, 0x0001}, {0xa436, 0xb820}, {0xa438, 0x0090}, {0xa436, 0xa012}, {0xa438, 0x0000}, {0xa436, 0xa014}, {0xa438, 0x2c04}, {0xa438, 0x2c6c},
-        {0xa438, 0x2c75}, {0xa438, 0x2c77}, {0xa438, 0x1414}, {0xa438, 0x1579}, {0xa438, 0x1536}, {0xa438, 0xc432}, {0xa438, 0x32c0}, {0xa438, 0x42d6}, {0xa438, 0x32b5}, {0xa438, 0x003e},
-        {0xa438, 0x614c}, {0xa438, 0x1569}, {0xa438, 0xd705}, {0xa438, 0x318c}, {0xa438, 0x42d6}, {0xa438, 0xd702}, {0xa438, 0x31ef}, {0xa438, 0x42d6}, {0xa438, 0x629c}, {0xa438, 0x2c04},
-        {0xa438, 0x653c}, {0xa438, 0x422a}, {0xa438, 0x5d83}, {0xa438, 0xd06a}, {0xa438, 0xd1b0}, {0xa438, 0x1536}, {0xa438, 0xc43a}, {0xa438, 0x32c0}, {0xa438, 0x42d6}, {0xa438, 0x32b5},
-        {0xa438, 0x003e}, {0xa438, 0x314a}, {0xa438, 0x42fe}, {0xa438, 0x337b}, {0xa438, 0x02d6}, {0xa438, 0x3063}, {0xa438, 0x0c1b}, {0xa438, 0x22fe}, {0xa438, 0xc435}, {0xa438, 0xd0be},
-        {0xa438, 0xd1f7}, {0xa438, 0xe0f0}, {0xa438, 0x1a40}, {0xa438, 0xa320}, {0xa438, 0xd702}, {0xa438, 0x154a}, {0xa438, 0xc434}, {0xa438, 0x32c0}, {0xa438, 0x42d6}, {0xa438, 0x32b5},
-        {0xa438, 0x003e}, {0xa438, 0x60ec}, {0xa438, 0x1569}, {0xa438, 0xd705}, {0xa438, 0x619f}, {0xa438, 0xd702}, {0xa438, 0x414f}, {0xa438, 0x2c2e}, {0xa438, 0x610a}, {0xa438, 0xd705},
-        {0xa438, 0x5e1f}, {0xa438, 0xc43f}, {0xa438, 0xc88b}, {0xa438, 0xd702}, {0xa438, 0x7fe0}, {0xa438, 0x22f3}, {0xa438, 0xd0a0}, {0xa438, 0xd1b2}, {0xa438, 0xd0c3}, {0xa438, 0xd1c3},
-        {0xa438, 0x8d01}, {0xa438, 0x1536}, {0xa438, 0xc438}, {0xa438, 0xe0f0}, {0xa438, 0x1a80}, {0xa438, 0xd706}, {0xa438, 0x60c0}, {0xa438, 0xd710}, {0xa438, 0x409e}, {0xa438, 0xa804},
-        {0xa438, 0xad01}, {0xa438, 0x8804}, {0xa438, 0xd702}, {0xa438, 0x32c0}, {0xa438, 0x42d6}, {0xa438, 0x32b5}, {0xa438, 0x003e}, {0xa438, 0x405b}, {0xa438, 0x1576}, {0xa438, 0x7c9c},
-        {0xa438, 0x60ec}, {0xa438, 0x1569}, {0xa438, 0xd702}, {0xa438, 0x5d43}, {0xa438, 0x31ef}, {0xa438, 0x02fe}, {0xa438, 0x22d6}, {0xa438, 0x590a}, {0xa438, 0xd706}, {0xa438, 0x5c80},
-        {0xa438, 0xd702}, {0xa438, 0x5c44}, {0xa438, 0x3063}, {0xa438, 0x02d6}, {0xa438, 0x5be2}, {0xa438, 0x22fb}, {0xa438, 0xa240}, {0xa438, 0xa104}, {0xa438, 0x8c03}, {0xa438, 0x8178},
-        {0xa438, 0xd701}, {0xa438, 0x31ad}, {0xa438, 0x4917}, {0xa438, 0x8102}, {0xa438, 0x2917}, {0xa438, 0xc302}, {0xa438, 0x268a}, {0xa436, 0xA01A}, {0xa438, 0x0000}, {0xa436, 0xA006},
-        {0xa438, 0x0fff}, {0xa436, 0xA004}, {0xa438, 0x0689}, {0xa436, 0xA002}, {0xa438, 0x0911}, {0xa436, 0xA000}, {0xa438, 0x7302}, {0xa436, 0xB820}, {0xa438, 0x0010}, {0xa436, 0x8412},
-        {0xa438, 0xaf84}, {0xa438, 0x1eaf}, {0xa438, 0x8427}, {0xa438, 0xaf84}, {0xa438, 0x27af}, {0xa438, 0x8427}, {0xa438, 0x0251}, {0xa438, 0x6802}, {0xa438, 0x8427}, {0xa438, 0xaf04},
-        {0xa438, 0x0af8}, {0xa438, 0xf9bf}, {0xa438, 0x5581}, {0xa438, 0x0255}, {0xa438, 0x27ef}, {0xa438, 0x310d}, {0xa438, 0x345b}, {0xa438, 0x0fa3}, {0xa438, 0x032a}, {0xa438, 0xe087},
-        {0xa438, 0xffac}, {0xa438, 0x2040}, {0xa438, 0xbf56}, {0xa438, 0x7402}, {0xa438, 0x5527}, {0xa438, 0xef31}, {0xa438, 0xef20}, {0xa438, 0xe787}, {0xa438, 0xfee6}, {0xa438, 0x87fd},
-        {0xa438, 0xd488}, {0xa438, 0x88bf}, {0xa438, 0x5674}, {0xa438, 0x0254}, {0xa438, 0xe3e0}, {0xa438, 0x87ff}, {0xa438, 0xf720}, {0xa438, 0xe487}, {0xa438, 0xffaf}, {0xa438, 0x847e},
-        {0xa438, 0xe087}, {0xa438, 0xffad}, {0xa438, 0x2016}, {0xa438, 0xe387}, {0xa438, 0xfee2}, {0xa438, 0x87fd}, {0xa438, 0xef45}, {0xa438, 0xbf56}, {0xa438, 0x7402}, {0xa438, 0x54e3},
-        {0xa438, 0xe087}, {0xa438, 0xfff6}, {0xa438, 0x20e4}, {0xa438, 0x87ff}, {0xa438, 0xfdfc}, {0xa438, 0x0400}, {0xa436, 0xb818}, {0xa438, 0x0407}, {0xa436, 0xb81a}, {0xa438, 0xfffd},
-        {0xa436, 0xb81c}, {0xa438, 0xfffd}, {0xa436, 0xb81e}, {0xa438, 0xfffd}, {0xa436, 0xb832}, {0xa438, 0x0001}, {0xb820, 0x0000}, {0xb82e, 0x0000}, {0xa436, 0x8028}, {0xa438, 0x0000}
-};
-
-static rtk_api_ret_t _rtk_switch_init_8367c(void)
-{
-    rtk_port_t port;
-    rtk_uint32 retVal;
-    rtk_uint32 regData;
-    rtk_uint32 regValue;
-
-    if( (retVal = rtl8367c_setAsicReg(0x13c2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if( (retVal = rtl8367c_getAsicReg(0x1301, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if( (retVal = rtl8367c_setAsicReg(0x13c2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    RTK_SCAN_ALL_LOG_PORT(port)
-    {
-         if(rtk_switch_isUtpPort(port) == RT_ERR_OK)
-         {
-             if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_PORT0_EEECFG + (0x20 * port), RTL8367C_PORT0_EEECFG_EEE_100M_OFFSET, 1)) != RT_ERR_OK)
-                 return retVal;
-
-             if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_PORT0_EEECFG + (0x20 * port), RTL8367C_PORT0_EEECFG_EEE_GIGA_500M_OFFSET, 1)) != RT_ERR_OK)
-                 return retVal;
-
-             if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_PORT0_EEECFG + (0x20 * port), RTL8367C_PORT0_EEECFG_EEE_TX_OFFSET, 1)) != RT_ERR_OK)
-                 return retVal;
-
-             if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_PORT0_EEECFG + (0x20 * port), RTL8367C_PORT0_EEECFG_EEE_RX_OFFSET, 1)) != RT_ERR_OK)
-                 return retVal;
-
-             if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xA428, &regData)) != RT_ERR_OK)
-                return retVal;
-
-             regData &= ~(0x0200);
-             if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xA428, regData)) != RT_ERR_OK)
-                 return retVal;
-
-             if((regValue & 0x00F0) == 0x00A0)
-             {
-                 if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xA5D0, &regData)) != RT_ERR_OK)
-                     return retVal;
-
-                 regData |= 0x0006;
-                 if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xA5D0, regData)) != RT_ERR_OK)
-                     return retVal;
-             }
-         }
-    }
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_UTP_FIB_DET, 0x15BB)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x1303, 0x06D6)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x1304, 0x0700)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13E2, 0x003F)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13F9, 0x0090)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x121e, 0x03CA)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x1233, 0x0352)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x1237, 0x00a0)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x123a, 0x0030)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x1239, 0x0084)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x0301, 0x1000)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x1349, 0x001F)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(0x18e0, 0, 0)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(0x122b, 14, 1)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBits(0x1305, 0xC000, 3)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-static rtk_api_ret_t _rtk_switch_init_8370b(void)
-{
-    ret_t retVal;
-    rtk_uint32 regData, tmp = 0;
-    rtk_uint32 i, prf, counter;
-    rtk_uint32 long_link[8] = {0x0210, 0x03e8, 0x0218, 0x03f0, 0x0220, 0x03f8, 0x0208, 0x03e0 };
-
-    if((retVal = rtl8367c_setAsicRegBits(0x1205, 0x0300, 3)) != RT_ERR_OK)
-        return retVal;
-
-
-    for(i=0; i<8; i++)
-    {
-      if ((retVal = rtl8367c_getAsicPHYOCPReg(i, 0xa420, &regData)) != RT_ERR_OK)
-          return retVal;
-        tmp = regData & 0x7 ;
-       if(tmp == 0x3)
-       {
-           prf = 1;
-           if((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xb83e, 0x6fa9)) != RT_ERR_OK)
-              return retVal;
-           if((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xb840, 0xa9)) != RT_ERR_OK)
-               return retVal;
-           for(counter = 0; counter < 10000; counter++); //delay
-
-           if ((retVal = rtl8367c_getAsicPHYOCPReg(i, 0xb820, &regData)) != RT_ERR_OK)
-               return retVal;
-           tmp = regData | 0x10;
-           if ((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xb820, tmp)) != RT_ERR_OK)
-               return retVal;
-           for(counter = 0; counter < 10000; counter++); //delay
-           counter = 0;
-           do{
-              counter = counter + 1;
-              if ((retVal = rtl8367c_getAsicPHYOCPReg(i, 0xb800, &regData)) != RT_ERR_OK)
-                   return retVal;
-              tmp = regData & 0x40;
-              if(tmp != 0)
-                break;
-           } while (counter < 20);   //Wait for patch ready = 1...
-       }
-   }
-    if ((retVal = rtl8367c_getAsicReg(0x1d01, &regData)) != RT_ERR_OK)
-        return retVal;
-    tmp = regData;
-    tmp = tmp | 0x3BE0; /*Broadcast port enable*/
-    tmp = tmp & 0xFFE0; /*Phy_id = 0 */
-    if((retVal = rtl8367c_setAsicReg(0x1d01, tmp)) != RT_ERR_OK)
-        return retVal;
-
-    for(i=0;i < 210; i++)
-    {
-        if((retVal = rtl8367c_setAsicPHYOCPReg(0, PatchChipData[i][0], PatchChipData[i][1])) != RT_ERR_OK)
-             return retVal;
-    }
-
-   if((retVal = rtl8367c_setAsicReg(0x1d01, regData)) != RT_ERR_OK)
-        return retVal;
-
-    for(i=0; i < 8; i++)
-    {
-        if((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xa4b4, long_link[i])) != RT_ERR_OK)
-             return retVal;
-    }
-
-  if (prf == 0x1)
-     {
-        for(i=0; i<8; i++)
-        {
-         if ((retVal = rtl8367c_getAsicPHYOCPReg(i, 0xb820, &regData)) != RT_ERR_OK)
-             return retVal;
-       tmp = regData & 0xFFEF;
-       if ((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xb820, tmp)) != RT_ERR_OK)
-             return retVal;
-
-       for(counter = 0; counter < 10000; counter++); //delay
-
-       counter = 0;
-       do{
-            counter = counter + 1;
-            if ((retVal = rtl8367c_getAsicPHYOCPReg(i, 0xb800, &regData)) != RT_ERR_OK)
-              return retVal;
-            tmp = regData & 0x40;
-            if( tmp == 0 )
-               break;
-       } while (counter < 20);   //Wait for patch ready = 1...
-      if ((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xb83e, 0x6f48)) != RT_ERR_OK)
-          return retVal;
-      if ((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xb840, 0xfa)) != RT_ERR_OK)
-          return retVal;
-          }
-   }
-
-    /*Check phy link status*/
-    for(i=0; i<8; i++)
-    {
-      if ((retVal = rtl8367c_getAsicPHYOCPReg(i, 0xa400, &regData)) != RT_ERR_OK)
-          return retVal;
-      tmp = regData & 0x800;
-        if(tmp == 0x0)
-            {
-              tmp = regData | 0x200;
-          if ((retVal = rtl8367c_setAsicPHYOCPReg(i, 0xa400, tmp)) != RT_ERR_OK)
-             return retVal;
-            }
-    }
-
-  for(counter = 0; counter < 10000; counter++); //delay
-
-  return RT_ERR_OK;
-}
-
-static rtk_api_ret_t _rtk_switch_init_8364b(void)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    /*enable EEE, include mac & phy*/
-
-    if ((retVal = rtl8367c_setAsicRegBits(0x38, 0x300, 3)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x78, 0x300, 3)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0xd8, 0x300, 0)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0xf8, 0x300, 0)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPHYOCPReg(1, 0xa5d0, 6)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicPHYOCPReg(3, 0xa5d0, 6)) != RT_ERR_OK)
-        return retVal;
-
-    /*PAD para*/
-
-    /*EXT1 PAD Para*/
-    if ((retVal = rtl8367c_getAsicReg(0x1303, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFFFFFFE;
-    regData |= 0x250;
-    if((retVal = rtl8367c_setAsicReg(0x1303, regData)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRegBits(0x1304, 0x7000, 0)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x1304, 0x700, 7)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x13f9, 0x38, 0)) != RT_ERR_OK)
-        return retVal;
-
-    /*EXT2 PAD Para*/
-    if ((retVal = rtl8367c_setAsicRegBit(0x1303, 10, 1)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x13E2, 0x1ff, 0x26)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x13f9, 0x1c0, 0)) != RT_ERR_OK)
-        return retVal;
-
-
-    /*SDS PATCH*/
-    /*SP_CFG_EN_LINK_FIB1G*/
-    if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData |= 0x4;
-    if((retVal = rtl8367c_setAsicSdsReg(0,4,0, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /*FIB100 Down-speed*/
-    if((retVal = rtl8367c_getAsicSdsReg(0, 1, 0, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData |= 0x20;
-    if((retVal = rtl8367c_setAsicSdsReg(0,1,0, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-static rtk_api_ret_t _rtk_switch_init_8363sc_vb(void)
-{
-
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    /*enable EEE, include mac & phy*/
-
-    if ((retVal = rtl8367c_setAsicRegBits(0x38, 0x300, 3)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x78, 0x300, 3)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0xd8, 0x300, 0)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0xf8, 0x300, 0)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPHYOCPReg(1, 0xa5d0, 6)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicPHYOCPReg(3, 0xa5d0, 6)) != RT_ERR_OK)
-        return retVal;
-
-    /*PAD para*/
-
-    /*EXT1 PAD Para*/
-    if ((retVal = rtl8367c_getAsicReg(0x1303, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFFFFFFE;
-    regData |= 0x250;
-    if((retVal = rtl8367c_setAsicReg(0x1303, regData)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRegBits(0x1304, 0x7000, 0)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x1304, 0x700, 7)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x13f9, 0x38, 0)) != RT_ERR_OK)
-        return retVal;
-
-    /*EXT2 PAD Para*/
-    if ((retVal = rtl8367c_setAsicRegBit(0x1303, 10, 1)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x13E2, 0x1ff, 0x26)) != RT_ERR_OK)
-        return retVal;
-    if ((retVal = rtl8367c_setAsicRegBits(0x13f9, 0x1c0, 0)) != RT_ERR_OK)
-        return retVal;
-
-
-    /*SDS PATCH*/
-    /*SP_CFG_EN_LINK_FIB1G*/
-    if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData |= 0x4;
-    if((retVal = rtl8367c_setAsicSdsReg(0,4,0, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /*FIB100 Down-speed*/
-    if((retVal = rtl8367c_getAsicSdsReg(0, 1, 0, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData |= 0x20;
-    if((retVal = rtl8367c_setAsicSdsReg(0,1,0, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_probe
- * Description:
- *      Probe switch
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Switch probed
- *      RT_ERR_FAILED   - Switch Unprobed.
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_probe(switch_chip_t *pSwitchChip)
-{
-#if defined(FORCE_PROBE_RTL8367C)
-
-    *pSwitchChip = CHIP_RTL8367C;
-    halCtrl = &rtl8367c_hal_Ctrl;
-
-#elif defined(FORCE_PROBE_RTL8370B)
-
-    *pSwitchChip = CHIP_RTL8370B;
-    halCtrl = &rtl8370b_hal_Ctrl;
-
-#elif defined(FORCE_PROBE_RTL8364B)
-
-    *pSwitchChip = CHIP_RTL8364B;
-    halCtrl = &rtl8364b_hal_Ctrl;
-
-#elif defined(FORCE_PROBE_RTL8363SC_VB)
-
-    *pSwitchChip = CHIP_RTL8363SC_VB;
-    halCtrl = &rtl8363sc_vb_hal_Ctrl;
-
-#else
-    rtk_uint32 retVal;
-    rtk_uint32 data, regValue;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &data)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1301, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    switch (data)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            *pSwitchChip = CHIP_RTL8367C;
-            halCtrl = &rtl8367c_hal_Ctrl;
-            break;
-        case 0x0652:
-        case 0x6368:
-            *pSwitchChip = CHIP_RTL8370B;
-            halCtrl = &rtl8370b_hal_Ctrl;
-            break;
-        case 0x0801:
-        case 0x6511:
-            if( (regValue & 0x00F0) == 0x0080)
-            {
-                *pSwitchChip = CHIP_RTL8363SC_VB;
-                halCtrl = &rtl8363sc_vb_hal_Ctrl;
-            }
-            else
-            {
-                *pSwitchChip = CHIP_RTL8364B;
-                halCtrl = &rtl8364b_hal_Ctrl;
-            }
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-#endif
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_initialState_set
- * Description:
- *      Set initial status
- * Input:
- *      state   - Initial state;
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Initialized
- *      RT_ERR_FAILED   - Uninitialized
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_initialState_set(init_state_t state)
-{
-    if(state >= INIT_STATE_END)
-        return RT_ERR_FAILED;
-
-    init_state = state;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_initialState_get
- * Description:
- *      Get initial status
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      INIT_COMPLETED     - Initialized
- *      INIT_NOT_COMPLETED - Uninitialized
- * Note:
- *
- */
-init_state_t rtk_switch_initialState_get(void)
-{
-    return init_state;
-}
-
-/* Function Name:
- *      rtk_switch_logicalPortCheck
- * Description:
- *      Check logical port ID.
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is correct
- *      RT_ERR_FAILED   - Port ID is not correct
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_logicalPortCheck(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if(halCtrl->l2p_port[logicalPort] == 0xFF)
-        return RT_ERR_FAILED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_isUtpPort
- * Description:
- *      Check is logical port a UTP port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a UTP port
- *      RT_ERR_FAILED   - Port ID is not a UTP port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isUtpPort(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if(halCtrl->log_port_type[logicalPort] == UTP_PORT)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_switch_isExtPort
- * Description:
- *      Check is logical port a Extension port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a EXT port
- *      RT_ERR_FAILED   - Port ID is not a EXT port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isExtPort(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if(halCtrl->log_port_type[logicalPort] == EXT_PORT)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_FAILED;
-}
-
-
-/* Function Name:
- *      rtk_switch_isHsgPort
- * Description:
- *      Check is logical port a HSG port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a HSG port
- *      RT_ERR_FAILED   - Port ID is not a HSG port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isHsgPort(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if(logicalPort == halCtrl->hsg_logical_port)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_switch_isSgmiiPort
- * Description:
- *      Check is logical port a SGMII port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a SGMII port
- *      RT_ERR_FAILED   - Port ID is not a SGMII port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isSgmiiPort(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if( ((0x01 << logicalPort) & halCtrl->sg_logical_portmask) != 0)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_switch_isCPUPort
- * Description:
- *      Check is logical port a CPU port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a CPU port
- *      RT_ERR_FAILED   - Port ID is not a CPU port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isCPUPort(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if( ((0x01 << logicalPort) & halCtrl->valid_cpu_portmask) != 0)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_switch_isComboPort
- * Description:
- *      Check is logical port a Combo port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a combo port
- *      RT_ERR_FAILED   - Port ID is not a combo port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isComboPort(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if(halCtrl->combo_logical_port == logicalPort)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_switch_ComboPort_get
- * Description:
- *      Get Combo port ID
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      Port ID of combo port
- * Note:
- *
- */
-rtk_uint32 rtk_switch_ComboPort_get(void)
-{
-    return halCtrl->combo_logical_port;
-}
-
-/* Function Name:
- *      rtk_switch_isPtpPort
- * Description:
- *      Check is logical port a PTP port
- * Input:
- *      logicalPort     - logical port ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Port ID is a PTP port
- *      RT_ERR_FAILED   - Port ID is not a PTP port
- *      RT_ERR_NOT_INIT - Not Initialize
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isPtpPort(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return RT_ERR_FAILED;
-
-    if(halCtrl->ptp_port[logicalPort] == 1)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_FAILED;
-}
-
-/* Function Name:
- *      rtk_switch_port_L2P_get
- * Description:
- *      Get physical port ID
- * Input:
- *      logicalPort       - logical port ID
- * Output:
- *      None
- * Return:
- *      Physical port ID
- * Note:
- *
- */
-rtk_uint32 rtk_switch_port_L2P_get(rtk_port_t logicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return UNDEFINE_PHY_PORT;
-
-    if(logicalPort >= RTK_SWITCH_PORT_NUM)
-        return UNDEFINE_PHY_PORT;
-
-    return (halCtrl->l2p_port[logicalPort]);
-}
-
-/* Function Name:
- *      rtk_switch_port_P2L_get
- * Description:
- *      Get logical port ID
- * Input:
- *      physicalPort       - physical port ID
- * Output:
- *      None
- * Return:
- *      logical port ID
- * Note:
- *
- */
-rtk_port_t rtk_switch_port_P2L_get(rtk_uint32 physicalPort)
-{
-    if(init_state != INIT_COMPLETED)
-        return UNDEFINE_PORT;
-
-    if(physicalPort >= RTK_SWITCH_PORT_NUM)
-        return UNDEFINE_PORT;
-
-    return (halCtrl->p2l_port[physicalPort]);
-}
-
-/* Function Name:
- *      rtk_switch_isPortMaskValid
- * Description:
- *      Check portmask is valid or not
- * Input:
- *      pPmask       - logical port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - port mask is valid
- *      RT_ERR_FAILED       - port mask is not valid
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isPortMaskValid(rtk_portmask_t *pPmask)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(NULL == pPmask)
-        return RT_ERR_NULL_POINTER;
-
-    if( (pPmask->bits[0] | halCtrl->valid_portmask) != halCtrl->valid_portmask )
-        return RT_ERR_FAILED;
-    else
-        return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_isPortMaskUtp
- * Description:
- *      Check all ports in portmask are only UTP port
- * Input:
- *      pPmask       - logical port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Only UTP port in port mask
- *      RT_ERR_FAILED       - Not only UTP port in port mask
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isPortMaskUtp(rtk_portmask_t *pPmask)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(NULL == pPmask)
-        return RT_ERR_NULL_POINTER;
-
-    if( (pPmask->bits[0] | halCtrl->valid_utp_portmask) != halCtrl->valid_utp_portmask )
-        return RT_ERR_FAILED;
-    else
-        return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_isPortMaskExt
- * Description:
- *      Check all ports in portmask are only EXT port
- * Input:
- *      pPmask       - logical port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Only EXT port in port mask
- *      RT_ERR_FAILED       - Not only EXT port in port mask
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_isPortMaskExt(rtk_portmask_t *pPmask)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(NULL == pPmask)
-        return RT_ERR_NULL_POINTER;
-
-    if( (pPmask->bits[0] | halCtrl->valid_ext_portmask) != halCtrl->valid_ext_portmask )
-        return RT_ERR_FAILED;
-    else
-        return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_portmask_L2P_get
- * Description:
- *      Get physicl portmask from logical portmask
- * Input:
- *      pLogicalPmask       - logical port mask
- * Output:
- *      pPhysicalPortmask   - physical port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- *      RT_ERR_PORT_MASK    - Error port mask
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_portmask_L2P_get(rtk_portmask_t *pLogicalPmask, rtk_uint32 *pPhysicalPortmask)
-{
-    rtk_uint32 log_port, phy_port;
-
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(NULL == pLogicalPmask)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pPhysicalPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if(rtk_switch_isPortMaskValid(pLogicalPmask) != RT_ERR_OK)
-        return RT_ERR_PORT_MASK;
-
-    /* reset physical port mask */
-    *pPhysicalPortmask = 0;
-
-    RTK_PORTMASK_SCAN((*pLogicalPmask), log_port)
-    {
-        phy_port = rtk_switch_port_L2P_get((rtk_port_t)log_port);
-        *pPhysicalPortmask |= (0x0001 << phy_port);
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_portmask_P2L_get
- * Description:
- *      Get logical portmask from physical portmask
- * Input:
- *      physicalPortmask    - physical port mask
- * Output:
- *      pLogicalPmask       - logical port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- *      RT_ERR_PORT_MASK    - Error port mask
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_portmask_P2L_get(rtk_uint32 physicalPortmask, rtk_portmask_t *pLogicalPmask)
-{
-    rtk_uint32 log_port, phy_port;
-
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_NOT_INIT;
-
-    if(NULL == pLogicalPmask)
-        return RT_ERR_NULL_POINTER;
-
-    RTK_PORTMASK_CLEAR(*pLogicalPmask);
-
-    for(phy_port = halCtrl->min_phy_port; phy_port <= halCtrl->max_phy_port; phy_port++)
-    {
-        if(physicalPortmask & (0x0001 << phy_port))
-        {
-            log_port = rtk_switch_port_P2L_get(phy_port);
-            if(log_port != UNDEFINE_PORT)
-            {
-                RTK_PORTMASK_PORT_SET(*pLogicalPmask, log_port);
-            }
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_phyPortMask_get
- * Description:
- *      Get physical portmask
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      0x00                - Not Initialize
- *      Other value         - Physical port mask
- * Note:
- *
- */
-rtk_uint32 rtk_switch_phyPortMask_get(void)
-{
-    if(init_state != INIT_COMPLETED)
-        return 0x00; /* No port in portmask */
-
-    return (halCtrl->phy_portmask);
-}
-
-/* Function Name:
- *      rtk_switch_logPortMask_get
- * Description:
- *      Get Logical portmask
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_NOT_INIT     - Not Initialize
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_switch_logPortMask_get(rtk_portmask_t *pPortmask)
-{
-    if(init_state != INIT_COMPLETED)
-        return RT_ERR_FAILED;
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    pPortmask->bits[0] = halCtrl->valid_portmask;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_init
- * Description:
- *      Set chip to default configuration enviroment
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API can set chip registers to default configuration for different release chip model.
- */
-rtk_api_ret_t rtk_switch_init(void)
-{
-    rtk_uint32  retVal;
-    rtl8367c_rma_t rmaCfg;
-    switch_chip_t   switchChip;
-
-    /* probe switch */
-    if((retVal = rtk_switch_probe(&switchChip)) != RT_ERR_OK)
-        return retVal;
-
-    /* Set initial state */
-
-    if((retVal = rtk_switch_initialState_set(INIT_COMPLETED)) != RT_ERR_OK)
-        return retVal;
-
-    /* Initial */
-    switch(switchChip)
-    {
-        case CHIP_RTL8367C:
-            if((retVal = _rtk_switch_init_8367c()) != RT_ERR_OK)
-                return retVal;
-            break;
-        case CHIP_RTL8370B:
-            if((retVal = _rtk_switch_init_8370b()) != RT_ERR_OK)
-                return retVal;
-            break;
-        case CHIP_RTL8364B:
-            if((retVal = _rtk_switch_init_8364b()) != RT_ERR_OK)
-                return retVal;
-            break;
-        case CHIP_RTL8363SC_VB:
-            if((retVal = _rtk_switch_init_8363sc_vb()) != RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            return RT_ERR_CHIP_NOT_FOUND;
-    }
-
-    /* Set Old max packet length to 16K */
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_MAX_LENGTH_LIMINT_IPG, RTL8367C_MAX_LENTH_CTRL_MASK, 3)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_MAX_LEN_RX_TX, RTL8367C_MAX_LEN_RX_TX_MASK, 3)) != RT_ERR_OK)
-        return retVal;
-
-    /* ACL Mode */
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_ACL_ACCESS_MODE, RTL8367C_ACL_ACCESS_MODE_MASK, 1)) != RT_ERR_OK)
-        return retVal;
-
-    /* Max rate */
-    if((retVal = rtk_rate_igrBandwidthCtrlRate_set(halCtrl->hsg_logical_port, RTL8367C_QOS_RATE_INPUT_MAX_HSG, DISABLED, ENABLED)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtk_rate_egrBandwidthCtrlRate_set(halCtrl->hsg_logical_port, RTL8367C_QOS_RATE_INPUT_MAX_HSG, ENABLED)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x03fa, 0x0007)) != RT_ERR_OK)
-        return retVal;
-
-    /* Change unknown DA to per port setting */
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_PORT_SECURIT_CTRL_REG, RTL8367C_UNKNOWN_UNICAST_DA_BEHAVE_MASK, 3)) != RT_ERR_OK)
-        return retVal;
-
-    /* LUT lookup OP = 1 */
-    if ((retVal = rtl8367c_setAsicLutIpLookupMethod(1))!=RT_ERR_OK)
-        return retVal;
-
-    /* Set RMA */
-    rmaCfg.portiso_leaky = 0;
-    rmaCfg.vlan_leaky = 0;
-    rmaCfg.keep_format = 0;
-    rmaCfg.trap_priority = 0;
-    rmaCfg.discard_storm_filter = 0;
-    rmaCfg.operation = 0;
-    if ((retVal = rtl8367c_setAsicRma(2, &rmaCfg))!=RT_ERR_OK)
-        return retVal;
-
-    /* Enable TX Mirror isolation leaky */
-    if ((retVal = rtl8367c_setAsicPortMirrorIsolationTxLeaky(ENABLED)) != RT_ERR_OK)
-        return retVal;
-
-    /* INT EN */
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IO_MISC_FUNC, RTL8367C_INT_EN_OFFSET, 1)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_portMaxPktLen_set
- * Description:
- *      Set Max packet length
- * Input:
- *      port    - Port ID
- *      speed   - Speed
- *      cfgId   - Configuration ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-rtk_api_ret_t rtk_switch_portMaxPktLen_set(rtk_port_t port, rtk_switch_maxPktLen_linkSpeed_t speed, rtk_uint32 cfgId)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(speed >= MAXPKTLEN_LINK_SPEED_END)
-        return RT_ERR_INPUT;
-
-    if(cfgId > MAXPKTLEN_CFG_ID_MAX)
-        return RT_ERR_INPUT;
-
-    if((retVal = rtl8367c_setAsicMaxLength(rtk_switch_port_L2P_get(port), (rtk_uint32)speed, cfgId)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_portMaxPktLen_get
- * Description:
- *      Get Max packet length
- * Input:
- *      port    - Port ID
- *      speed   - Speed
- * Output:
- *      pCfgId  - Configuration ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-rtk_api_ret_t rtk_switch_portMaxPktLen_get(rtk_port_t port, rtk_switch_maxPktLen_linkSpeed_t speed, rtk_uint32 *pCfgId)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(speed >= MAXPKTLEN_LINK_SPEED_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pCfgId)
-        return RT_ERR_NULL_POINTER;
-
-    if((retVal = rtl8367c_getAsicMaxLength(rtk_switch_port_L2P_get(port), (rtk_uint32)speed, pCfgId)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_maxPktLenCfg_set
- * Description:
- *      Set Max packet length configuration
- * Input:
- *      cfgId   - Configuration ID
- *      pktLen  - Max packet length
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-rtk_api_ret_t rtk_switch_maxPktLenCfg_set(rtk_uint32 cfgId, rtk_uint32 pktLen)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(cfgId > MAXPKTLEN_CFG_ID_MAX)
-        return RT_ERR_INPUT;
-
-    if(pktLen > RTK_SWITCH_MAX_PKTLEN)
-        return RT_ERR_INPUT;
-
-    if((retVal = rtl8367c_setAsicMaxLengthCfg(cfgId, pktLen)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_maxPktLenCfg_get
- * Description:
- *      Get Max packet length configuration
- * Input:
- *      cfgId   - Configuration ID
- *      pPktLen - Max packet length
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- */
-rtk_api_ret_t rtk_switch_maxPktLenCfg_get(rtk_uint32 cfgId, rtk_uint32 *pPktLen)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(cfgId > MAXPKTLEN_CFG_ID_MAX)
-        return RT_ERR_INPUT;
-
-    if(NULL == pPktLen)
-        return RT_ERR_NULL_POINTER;
-
-    if((retVal = rtl8367c_getAsicMaxLengthCfg(cfgId, pPktLen)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_greenEthernet_set
- * Description:
- *      Set all Ports Green Ethernet state.
- * Input:
- *      enable - Green Ethernet state.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - OK
- *      RT_ERR_FAILED   - Failed
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_ENABLE   - Invalid enable input.
- * Note:
- *      This API can set all Ports Green Ethernet state.
- *      The configuration is as following:
- *      - DISABLE
- *      - ENABLE
- */
-rtk_api_ret_t rtk_switch_greenEthernet_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    RTK_SCAN_ALL_LOG_PORT(port)
-    {
-        if(rtk_switch_isUtpPort(port) == RT_ERR_OK)
-        {
-            if ((retVal = rtl8367c_setAsicPowerSaving(rtk_switch_port_L2P_get(port),enable))!=RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicGreenEthernet(rtk_switch_port_L2P_get(port), enable))!=RT_ERR_OK)
-                return retVal;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_greenEthernet_get
- * Description:
- *      Get all Ports Green Ethernet state.
- * Input:
- *      None
- * Output:
- *      pEnable - Green Ethernet state.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- * Note:
- *      This API can get Green Ethernet state.
- */
-rtk_api_ret_t rtk_switch_greenEthernet_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 port;
-    rtk_uint32 state;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    RTK_SCAN_ALL_LOG_PORT(port)
-    {
-        if(rtk_switch_isUtpPort(port) == RT_ERR_OK)
-        {
-            if ((retVal = rtl8367c_getAsicPowerSaving(rtk_switch_port_L2P_get(port), &state))!=RT_ERR_OK)
-                return retVal;
-
-            if(state == DISABLED)
-            {
-                *pEnable = DISABLED;
-                return RT_ERR_OK;
-            }
-
-            if ((retVal = rtl8367c_getAsicGreenEthernet(rtk_switch_port_L2P_get(port), &state))!=RT_ERR_OK)
-                return retVal;
-
-            if(state == DISABLED)
-            {
-                *pEnable = DISABLED;
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    *pEnable = ENABLED;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_switch_maxLogicalPort_get
- * Description:
- *      Get Max logical port ID
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      Max logical port
- * Note:
- *      This API can get max logical port
- */
-rtk_port_t rtk_switch_maxLogicalPort_get(void)
-{
-    rtk_port_t port, maxLogicalPort = 0;
-
-    /* Check initialization state */
-    if(rtk_switch_initialState_get() != INIT_COMPLETED)
-    {
-        return UNDEFINE_PORT;
-    }
-
-    for(port = 0; port < RTK_SWITCH_PORT_NUM; port++)
-    {
-        if( (halCtrl->log_port_type[port] == UTP_PORT) || (halCtrl->log_port_type[port] == EXT_PORT) )
-            maxLogicalPort = port;
-    }
-
-    return maxLogicalPort;
-}
-
-/* Function Name:
- *      rtk_switch_maxMeterId_get
- * Description:
- *      Get Max Meter ID
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      0x00                - Not Initialize
- *      Other value         - Max Meter ID
- * Note:
- *
- */
-rtk_uint32 rtk_switch_maxMeterId_get(void)
-{
-    if(init_state != INIT_COMPLETED)
-        return 0x00;
-
-    return (halCtrl->max_meter_id);
-}
-
-/* Function Name:
- *      rtk_switch_maxLutAddrNumber_get
- * Description:
- *      Get Max LUT Address number
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      0x00                - Not Initialize
- *      Other value         - Max LUT Address number
- * Note:
- *
- */
-rtk_uint32 rtk_switch_maxLutAddrNumber_get(void)
-{
-    if(init_state != INIT_COMPLETED)
-        return 0x00;
-
-    return (halCtrl->max_lut_addr_num);
-}
-
-/* Function Name:
- *      rtk_switch_isValidTrunkGrpId
- * Description:
- *      Check if trunk group is valid or not
- * Input:
- *      grpId       - Group ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Trunk Group ID is valid
- *      RT_ERR_LA_TRUNK_ID  - Trunk Group ID is not valid
- * Note:
- *
- */
-rtk_uint32 rtk_switch_isValidTrunkGrpId(rtk_uint32 grpId)
-{
-    if(init_state != INIT_COMPLETED)
-        return 0x00;
-
-    if( (halCtrl->trunk_group_mask & (0x01 << grpId) ) != 0)
-        return RT_ERR_OK;
-    else
-        return RT_ERR_LA_TRUNK_ID;
-
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv.c
deleted file mode 100644
index 7858edcf53..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv.c
+++ /dev/null
@@ -1,639 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature :
- *
- */
-
-#include <rtl8367c_asicdrv.h>
-
-#if defined(RTK_X86_ASICDRV)
-#include <I2Clib.h>
-#else
-#include <smi.h>
-#endif
-
-/*for driver verify testing only*/
-#ifdef CONFIG_RTL8367C_ASICDRV_TEST
-#define CLE_VIRTUAL_REG_SIZE        0x10000
-rtk_uint16 CleVirtualReg[CLE_VIRTUAL_REG_SIZE];
-#endif
-
-#if defined(CONFIG_RTL865X_CLE) || defined (RTK_X86_CLE)
-rtk_uint32 cleDebuggingDisplay;
-#endif
-
-#ifdef EMBEDDED_SUPPORT
-extern void setReg(rtk_uint16, rtk_uint16);
-extern rtk_uint16 getReg(rtk_uint16);
-#endif
-
-/* Function Name:
- *      rtl8367c_setAsicRegBit
- * Description:
- *      Set a bit value of a specified register
- * Input:
- *      reg     - register's address
- *      bit     - bit location
- *      value   - value to set. It can be value 0 or 1.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameter
- * Note:
- *      Set a bit of a specified register to 1 or 0.
- */
-ret_t rtl8367c_setAsicRegBit(rtk_uint32 reg, rtk_uint32 bit, rtk_uint32 value)
-{
-
-#if defined(RTK_X86_ASICDRV)
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    if(bit >= RTL8367C_REGBITLENGTH)
-        return RT_ERR_INPUT;
-
-    retVal = Access_Read(reg, 2, &regData);
-    if(TRUE != retVal)
-        return RT_ERR_SMI;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-    if(value)
-        regData = regData | (1 << bit);
-    else
-        regData = regData & (~(1 << bit));
-
-    retVal = Access_Write(reg,2, regData);
-    if(TRUE != retVal)
-        return RT_ERR_SMI;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-
-#elif defined(CONFIG_RTL8367C_ASICDRV_TEST)
-
-    if(bit >= RTL8367C_REGBITLENGTH)
-        return RT_ERR_INPUT;
-
-    else if(reg >= CLE_VIRTUAL_REG_SIZE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(value)
-    {
-        CleVirtualReg[reg] =  CleVirtualReg[reg] | (1 << bit);
-    }
-    else
-    {
-        CleVirtualReg[reg] =  CleVirtualReg[reg] & (~(1 << bit));
-    }
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n", reg, CleVirtualReg[reg]);
-
-#elif defined(EMBEDDED_SUPPORT)
-    rtk_uint16 tmp;
-
-    if(reg > RTL8367C_REGDATAMAX || value > 1)
-        return RT_ERR_INPUT;
-
-    tmp = getReg(reg);
-    tmp &= (1 << bitIdx);
-    tmp |= (value << bitIdx);
-    setReg(reg, tmp);
-
-#else
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    if(bit >= RTL8367C_REGBITLENGTH)
-        return RT_ERR_INPUT;
-
-    retVal = smi_read(reg, &regData);
-    if(retVal != RT_ERR_OK)
-        return RT_ERR_SMI;
-
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-  #endif
-    if(value)
-        regData = regData | (1 << bit);
-    else
-        regData = regData & (~(1 << bit));
-
-    retVal = smi_write(reg, regData);
-    if(retVal != RT_ERR_OK)
-        return RT_ERR_SMI;
-
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n", reg, regData);
-  #endif
-
-#endif
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicRegBit
- * Description:
- *      Get a bit value of a specified register
- * Input:
- *      reg     - register's address
- *      bit     - bit location
- *      value   - value to get.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRegBit(rtk_uint32 reg, rtk_uint32 bit, rtk_uint32 *pValue)
-{
-
-#if defined(RTK_X86_ASICDRV)
-
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    if(bit >= RTL8367C_REGBITLENGTH)
-        return RT_ERR_INPUT;
-
-    retVal = Access_Read(reg, 2, &regData);
-    if(TRUE != retVal)
-        return RT_ERR_SMI;
-
-    *pValue = (regData & (0x1 << bit)) >> bit;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-#elif defined(CONFIG_RTL8367C_ASICDRV_TEST)
-
-    if(bit >= RTL8367C_REGBITLENGTH)
-        return RT_ERR_INPUT;
-
-    if(reg >= CLE_VIRTUAL_REG_SIZE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    *pValue = (CleVirtualReg[reg] & (0x1 << bit)) >> bit;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, CleVirtualReg[reg]);
-
-#elif defined(EMBEDDED_SUPPORT)
-    rtk_uint16 tmp;
-
-    if(reg > RTL8367C_REGDATAMAX )
-        return RT_ERR_INPUT;
-
-    tmp = getReg(reg);
-    tmp = tmp >> bitIdx;
-    tmp &= 1;
-    *value = tmp;
-#else
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    retVal = smi_read(reg, &regData);
-    if(retVal != RT_ERR_OK)
-        return RT_ERR_SMI;
-
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-  #endif
-
-    *pValue = (regData & (0x1 << bit)) >> bit;
-
-#endif
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicRegBits
- * Description:
- *      Set bits value of a specified register
- * Input:
- *      reg     - register's address
- *      bits    - bits mask for setting
- *      value   - bits value for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameter
- * Note:
- *      Set bits of a specified register to value. Both bits and value are be treated as bit-mask
- */
-ret_t rtl8367c_setAsicRegBits(rtk_uint32 reg, rtk_uint32 bits, rtk_uint32 value)
-{
-
-#if defined(RTK_X86_ASICDRV)
-
-    rtk_uint32 regData;
-    ret_t retVal;
-    rtk_uint32 bitsShift;
-    rtk_uint32 valueShifted;
-
-    if(bits >= (1 << RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1 << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-
-    valueShifted = value << bitsShift;
-    if(valueShifted > RTL8367C_REGDATAMAX)
-        return RT_ERR_INPUT;
-
-    retVal = Access_Read(reg, 2, &regData);
-    if(TRUE != retVal)
-        return RT_ERR_SMI;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-    regData = regData & (~bits);
-    regData = regData | (valueShifted & bits);
-
-    retVal = Access_Write(reg,2, regData);
-    if(TRUE != retVal)
-        return RT_ERR_SMI;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-#elif defined(CONFIG_RTL8367C_ASICDRV_TEST)
-    rtk_uint32 regData;
-    rtk_uint32 bitsShift;
-    rtk_uint32 valueShifted;
-
-    if(bits >= (1 << RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1 << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-    valueShifted = value << bitsShift;
-
-    if(valueShifted > RTL8367C_REGDATAMAX)
-        return RT_ERR_INPUT;
-
-    if(reg >= CLE_VIRTUAL_REG_SIZE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    regData = CleVirtualReg[reg] & (~bits);
-    regData = regData | (valueShifted & bits);
-
-    CleVirtualReg[reg] = regData;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-#elif defined(EMBEDDED_SUPPORT)
-    rtk_uint32 regData;
-    rtk_uint32 bitsShift;
-    rtk_uint32 valueShifted;
-
-    if(reg > RTL8367C_REGDATAMAX )
-        return RT_ERR_INPUT;
-
-    if(bits >= (1 << RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1 << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-
-    valueShifted = value << bitsShift;
-    if(valueShifted > RTL8367C_REGDATAMAX)
-        return RT_ERR_INPUT;
-
-    regData = getReg(reg);
-    regData = regData & (~bits);
-    regData = regData | (valueShifted & bits);
-
-    setReg(reg, regData);
-
-#else
-    rtk_uint32 regData;
-    ret_t retVal;
-    rtk_uint32 bitsShift;
-    rtk_uint32 valueShifted;
-
-    if(bits >= (1 << RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1 << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-    valueShifted = value << bitsShift;
-
-    if(valueShifted > RTL8367C_REGDATAMAX)
-        return RT_ERR_INPUT;
-
-    retVal = smi_read(reg, &regData);
-    if(retVal != RT_ERR_OK)
-        return RT_ERR_SMI;
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-  #endif
-
-    regData = regData & (~bits);
-    regData = regData | (valueShifted & bits);
-
-    retVal = smi_write(reg, regData);
-    if(retVal != RT_ERR_OK)
-        return RT_ERR_SMI;
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n", reg, regData);
-  #endif
-#endif
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicRegBits
- * Description:
- *      Get bits value of a specified register
- * Input:
- *      reg     - register's address
- *      bits    - bits mask for setting
- *      value   - bits value for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRegBits(rtk_uint32 reg, rtk_uint32 bits, rtk_uint32 *pValue)
-{
-
-#if defined(RTK_X86_ASICDRV)
-
-    rtk_uint32 regData;
-    ret_t retVal;
-    rtk_uint32 bitsShift;
-
-    if(bits >= (1 << RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1 << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-
-    retVal = Access_Read(reg, 2, &regData);
-    if(TRUE != retVal)
-        return RT_ERR_SMI;
-
-    *pValue = (regData & bits) >> bitsShift;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-#elif defined(CONFIG_RTL8367C_ASICDRV_TEST)
-    rtk_uint32 bitsShift;
-
-    if(bits >= (1 << RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1 << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-
-    if(reg >= CLE_VIRTUAL_REG_SIZE)
-        return RT_ERR_OUT_OF_RANGE;
-
-     *pValue = (CleVirtualReg[reg] & bits) >> bitsShift;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, CleVirtualReg[reg]);
-
-#elif defined(EMBEDDED_SUPPORT)
-    rtk_uint32 regData;
-    rtk_uint32 bitsShift;
-
-    if(reg > RTL8367C_REGDATAMAX )
-        return RT_ERR_INPUT;
-
-    if(bits >= (1UL << RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1UL << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-
-    regData = getReg(reg);
-    *value = (regData & bits) >> bitsShift;
-
-#else
-    rtk_uint32 regData;
-    ret_t retVal;
-    rtk_uint32 bitsShift;
-
-    if(bits>= (1<<RTL8367C_REGBITLENGTH) )
-        return RT_ERR_INPUT;
-
-    bitsShift = 0;
-    while(!(bits & (1 << bitsShift)))
-    {
-        bitsShift++;
-        if(bitsShift >= RTL8367C_REGBITLENGTH)
-            return RT_ERR_INPUT;
-    }
-
-    retVal = smi_read(reg, &regData);
-    if(retVal != RT_ERR_OK) return RT_ERR_SMI;
-
-    *pValue = (regData & bits) >> bitsShift;
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n",reg, regData);
-  #endif
-
-#endif
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicReg
- * Description:
- *      Set content of asic register
- * Input:
- *      reg     - register's address
- *      value   - Value setting to register
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      The value will be set to ASIC mapping address only and it is always return RT_ERR_OK while setting un-mapping address registers
- */
-ret_t rtl8367c_setAsicReg(rtk_uint32 reg, rtk_uint32 value)
-{
-#if defined(RTK_X86_ASICDRV)/*RTK-CNSD2-NickWu-20061222: for x86 compile*/
-
-    ret_t retVal;
-
-    retVal = Access_Write(reg,2,value);
-    if(TRUE != retVal) return RT_ERR_SMI;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n",reg,value);
-
-#elif defined(CONFIG_RTL8367C_ASICDRV_TEST)
-
-    /*MIBs emulating*/
-    if(reg == RTL8367C_REG_MIB_ADDRESS)
-    {
-        CleVirtualReg[RTL8367C_MIB_COUNTER_BASE_REG] = 0x1;
-        CleVirtualReg[RTL8367C_MIB_COUNTER_BASE_REG+1] = 0x2;
-        CleVirtualReg[RTL8367C_MIB_COUNTER_BASE_REG+2] = 0x3;
-        CleVirtualReg[RTL8367C_MIB_COUNTER_BASE_REG+3] = 0x4;
-    }
-
-    if(reg >= CLE_VIRTUAL_REG_SIZE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    CleVirtualReg[reg] = value;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n",reg,CleVirtualReg[reg]);
-
-#elif defined(EMBEDDED_SUPPORT)
-    if(reg > RTL8367C_REGDATAMAX || value > RTL8367C_REGDATAMAX )
-        return RT_ERR_INPUT;
-
-    setReg(reg, value);
-
-#else
-    ret_t retVal;
-
-    retVal = smi_write(reg, value);
-    if(retVal != RT_ERR_OK)
-        return RT_ERR_SMI;
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("W[0x%4.4x]=0x%4.4x\n",reg,value);
-  #endif
-
-#endif
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicReg
- * Description:
- *      Get content of asic register
- * Input:
- *      reg     - register's address
- *      value   - Value setting to register
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      Value 0x0000 will be returned for ASIC un-mapping address
- */
-ret_t rtl8367c_getAsicReg(rtk_uint32 reg, rtk_uint32 *pValue)
-{
-
-#if defined(RTK_X86_ASICDRV)
-
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    retVal = Access_Read(reg, 2, &regData);
-    if(TRUE != retVal)
-        return RT_ERR_SMI;
-
-    *pValue = regData;
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-
-#elif defined(CONFIG_RTL8367C_ASICDRV_TEST)
-    if(reg >= CLE_VIRTUAL_REG_SIZE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    *pValue = CleVirtualReg[reg];
-
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, CleVirtualReg[reg]);
-
-#elif defined(EMBEDDED_SUPPORT)
-    if(reg > RTL8367C_REGDATAMAX  )
-        return RT_ERR_INPUT;
-
-    *value = getReg(reg);
-
-#else
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    retVal = smi_read(reg, &regData);
-    if(retVal != RT_ERR_OK)
-        return RT_ERR_SMI;
-
-    *pValue = regData;
-  #ifdef CONFIG_RTL865X_CLE
-    if(0x8367B == cleDebuggingDisplay)
-        PRINT("R[0x%4.4x]=0x%4.4x\n", reg, regData);
-  #endif
-
-#endif
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_acl.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_acl.c
deleted file mode 100644
index d9ccd97118..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_acl.c
+++ /dev/null
@@ -1,1173 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : ACL related function drivers
- *
- */
-#include <rtl8367c_asicdrv_acl.h>
-
-#include <string.h>
-
-#if defined(CONFIG_RTL8367C_ASICDRV_TEST)
-rtl8367c_aclrulesmi Rtl8370sVirtualAclRuleTable[RTL8367C_ACLRULENO];
-rtk_uint16 Rtl8370sVirtualAclActTable[RTL8367C_ACLRULENO][RTL8367C_ACL_ACT_TABLE_LEN];
-#endif
-
-/*
-    Exchange structure type define with MMI and SMI
-*/
-static void _rtl8367c_aclRuleStSmi2User( rtl8367c_aclrule *pAclUser, rtl8367c_aclrulesmi *pAclSmi)
-{
-    rtk_uint8 *care_ptr, *data_ptr;
-    rtk_uint8 care_tmp, data_tmp;
-    rtk_uint32 i;
-
-    pAclUser->data_bits.active_portmsk = (((pAclSmi->data_bits_ext.rule_info >> 1) & 0x0007) << 8) | ((pAclSmi->data_bits.rule_info >> 8) & 0x00FF);
-    pAclUser->data_bits.type = (pAclSmi->data_bits.rule_info & 0x0007);
-    pAclUser->data_bits.tag_exist = (pAclSmi->data_bits.rule_info & 0x00F8) >> 3;
-
-    care_ptr = (rtk_uint8*)&pAclSmi->care_bits;
-    data_ptr = (rtk_uint8*)&pAclSmi->data_bits;
-
-    for ( i = 0; i < sizeof(struct acl_rule_smi_st); i++)
-    {
-        care_tmp = *(care_ptr + i) ^ (*(data_ptr + i));
-        data_tmp = *(data_ptr + i);
-
-        *(care_ptr + i) = care_tmp;
-        *(data_ptr + i) = data_tmp;
-    }
-
-    care_ptr = (rtk_uint8*)&pAclSmi->care_bits_ext;
-    data_ptr = (rtk_uint8*)&pAclSmi->data_bits_ext;
-    care_tmp = (*care_ptr) ^ (*data_ptr);
-    data_tmp = (*data_ptr);
-    *care_ptr = care_tmp;
-    *data_ptr = data_tmp;
-
-    for(i = 0; i < RTL8367C_ACLRULEFIELDNO; i++)
-        pAclUser->data_bits.field[i] = pAclSmi->data_bits.field[i];
-
-    pAclUser->valid = pAclSmi->valid;
-
-    pAclUser->care_bits.active_portmsk = (((pAclSmi->care_bits_ext.rule_info >> 1) & 0x0007) << 8) | ((pAclSmi->care_bits.rule_info >> 8) & 0x00FF);
-    pAclUser->care_bits.type = (pAclSmi->care_bits.rule_info & 0x0007);
-    pAclUser->care_bits.tag_exist = (pAclSmi->care_bits.rule_info & 0x00F8) >> 3;
-
-    for(i = 0; i < RTL8367C_ACLRULEFIELDNO; i++)
-        pAclUser->care_bits.field[i] = pAclSmi->care_bits.field[i];
-}
-
-/*
-    Exchange structure type define with MMI and SMI
-*/
-static void _rtl8367c_aclRuleStUser2Smi(rtl8367c_aclrule *pAclUser, rtl8367c_aclrulesmi *pAclSmi)
-{
-    rtk_uint8 *care_ptr, *data_ptr;
-    rtk_uint8 care_tmp, data_tmp;
-    rtk_uint32 i;
-
-    pAclSmi->data_bits_ext.rule_info = ((pAclUser->data_bits.active_portmsk >> 8) & 0x7) << 1;
-    pAclSmi->data_bits.rule_info = ((pAclUser->data_bits.active_portmsk & 0xff) << 8) | ((pAclUser->data_bits.tag_exist & 0x1F) << 3) | (pAclUser->data_bits.type & 0x07);
-
-    for(i = 0;i < RTL8367C_ACLRULEFIELDNO; i++)
-        pAclSmi->data_bits.field[i] = pAclUser->data_bits.field[i];
-
-    pAclSmi->valid = pAclUser->valid;
-
-    pAclSmi->care_bits_ext.rule_info = ((pAclUser->care_bits.active_portmsk >> 8) & 0x7) << 1;
-    pAclSmi->care_bits.rule_info = ((pAclUser->care_bits.active_portmsk & 0xff) << 8) | ((pAclUser->care_bits.tag_exist & 0x1F) << 3) | (pAclUser->care_bits.type & 0x07);
-
-    for(i = 0; i < RTL8367C_ACLRULEFIELDNO; i++)
-        pAclSmi->care_bits.field[i] = pAclUser->care_bits.field[i];
-
-    care_ptr = (rtk_uint8*)&pAclSmi->care_bits;
-    data_ptr = (rtk_uint8*)&pAclSmi->data_bits;
-
-    for ( i = 0; i < sizeof(struct acl_rule_smi_st); i++)
-    {
-        care_tmp = *(care_ptr + i) & ~(*(data_ptr + i));
-        data_tmp = *(care_ptr + i) & *(data_ptr + i);
-
-        *(care_ptr + i) = care_tmp;
-        *(data_ptr + i) = data_tmp;
-    }
-
-    care_ptr = (rtk_uint8*)&pAclSmi->care_bits_ext;
-    data_ptr = (rtk_uint8*)&pAclSmi->data_bits_ext;
-    care_tmp = *care_ptr & ~(*data_ptr);
-    data_tmp = *care_ptr & *data_ptr;
-
-    *care_ptr = care_tmp;
-    *data_ptr = data_tmp;
-}
-
-/*
-    Exchange structure type define with MMI and SMI
-*/
-static void _rtl8367c_aclActStSmi2User(rtl8367c_acl_act_t *pAclUser, rtk_uint16 *pAclSmi)
-{
-    pAclUser->cact = (pAclSmi[0] & 0x00C0) >> 6;
-    pAclUser->cvidx_cact = (pAclSmi[0] & 0x003F) | (((pAclSmi[3] & 0x0008) >> 3) << 6);
-
-    pAclUser->sact = (pAclSmi[0] & 0xC000) >> 14;
-    pAclUser->svidx_sact = ((pAclSmi[0] & 0x3F00) >> 8) | (((pAclSmi[3] & 0x0010) >> 4) << 6);
-
-    pAclUser->aclmeteridx = (pAclSmi[1] & 0x003F) | (((pAclSmi[3] & 0x0020) >> 5) << 6);
-
-    pAclUser->fwdact = (pAclSmi[1] & 0xC000) >> 14;
-    pAclUser->fwdpmask = ((pAclSmi[1] & 0x3FC0) >> 6) | (((pAclSmi[3] & 0x01C0) >> 6) << 8);
-
-    pAclUser->priact = (pAclSmi[2] & 0x00C0) >> 6;
-    pAclUser->pridx = (pAclSmi[2] & 0x003F) | (((pAclSmi[3] & 0x0200) >> 9) << 6);
-
-    pAclUser->aclint = (pAclSmi[2] & 0x2000) >> 13;
-    pAclUser->gpio_en = (pAclSmi[2] & 0x1000) >> 12;
-    pAclUser->gpio_pin = (pAclSmi[2] & 0x0F00) >> 8;
-
-    pAclUser->cact_ext = (pAclSmi[2] & 0xC000) >> 14;
-    pAclUser->tag_fmt = (pAclSmi[3] & 0x0003);
-    pAclUser->fwdact_ext = (pAclSmi[3] & 0x0004) >> 2;
-}
-
-/*
-    Exchange structure type define with MMI and SMI
-*/
-static void _rtl8367c_aclActStUser2Smi(rtl8367c_acl_act_t *pAclUser, rtk_uint16 *pAclSmi)
-{
-    pAclSmi[0] |= (pAclUser->cvidx_cact & 0x003F);
-    pAclSmi[0] |= (pAclUser->cact & 0x0003) << 6;
-    pAclSmi[0] |= (pAclUser->svidx_sact & 0x003F) << 8;
-    pAclSmi[0] |= (pAclUser->sact & 0x0003) << 14;
-
-    pAclSmi[1] |= (pAclUser->aclmeteridx & 0x003F);
-    pAclSmi[1] |= (pAclUser->fwdpmask & 0x00FF) << 6;
-    pAclSmi[1] |= (pAclUser->fwdact & 0x0003) << 14;
-
-    pAclSmi[2] |= (pAclUser->pridx & 0x003F);
-    pAclSmi[2] |= (pAclUser->priact & 0x0003) << 6;
-    pAclSmi[2] |= (pAclUser->gpio_pin & 0x000F) << 8;
-    pAclSmi[2] |= (pAclUser->gpio_en & 0x0001) << 12;
-    pAclSmi[2] |= (pAclUser->aclint & 0x0001) << 13;
-    pAclSmi[2] |= (pAclUser->cact_ext & 0x0003) << 14;
-
-    pAclSmi[3] |= (pAclUser->tag_fmt & 0x0003);
-    pAclSmi[3] |= (pAclUser->fwdact_ext & 0x0001) << 2;
-    pAclSmi[3] |= ((pAclUser->cvidx_cact & 0x0040) >> 6) << 3;
-    pAclSmi[3] |= ((pAclUser->svidx_sact & 0x0040) >> 6) << 4;
-    pAclSmi[3] |= ((pAclUser->aclmeteridx & 0x0040) >> 6) << 5;
-    pAclSmi[3] |= ((pAclUser->fwdpmask & 0x0700) >> 8) << 6;
-    pAclSmi[3] |= ((pAclUser->pridx & 0x0040) >> 6) << 9;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicAcl
- * Description:
- *      Set port acl function enable/disable
- * Input:
- *      port    - Physical port number (0~10)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAcl(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_ACL_ENABLE_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicAcl
- * Description:
- *      Get port acl function enable/disable
- * Input:
- *      port    - Physical port number (0~10)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAcl(rtk_uint32 port, rtk_uint32* pEnabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_ACL_ENABLE_REG, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicAclUnmatchedPermit
- * Description:
- *      Set port acl function unmatched permit action
- * Input:
- *      port    - Physical port number (0~10)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAclUnmatchedPermit(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_ACL_UNMATCH_PERMIT_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicAclUnmatchedPermit
- * Description:
- *      Get port acl function unmatched permit action
- * Input:
- *      port    - Physical port number (0~10)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclUnmatchedPermit(rtk_uint32 port, rtk_uint32* pEnabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_ACL_UNMATCH_PERMIT_REG, port, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicAclRule
- * Description:
- *      Set acl rule content
- * Input:
- *      index   - ACL rule index (0-95) of 96 ACL rules
- *      pAclRule - ACL rule stucture for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-95)
- * Note:
- *      System supported 95 shared 289-bit ACL ingress rule. Index was available at range 0-95 only.
- *      If software want to modify ACL rule, the ACL function should be disable at first or unspecify
- *      acl action will be executed.
- *      One ACL rule structure has three parts setting:
- *      Bit 0-147       Data Bits of this Rule
- *      Bit 148     Valid Bit
- *      Bit 149-296 Care Bits of this Rule
- *      There are four kinds of field in Data Bits and Care Bits: Active Portmask, Type, Tag Exist, and 8 fields
- */
-ret_t rtl8367c_setAsicAclRule(rtk_uint32 index, rtl8367c_aclrule* pAclRule)
-{
-    rtl8367c_aclrulesmi aclRuleSmi;
-    rtk_uint16* tableAddr;
-    rtk_uint32 regAddr;
-    rtk_uint32  regData;
-    rtk_uint32 i;
-    ret_t retVal;
-
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    memset(&aclRuleSmi, 0x00, sizeof(rtl8367c_aclrulesmi));
-
-    _rtl8367c_aclRuleStUser2Smi(pAclRule, &aclRuleSmi);
-
-    /* Write valid bit = 0 */
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    if(index >= 64)
-        regData = RTL8367C_ACLRULETBADDR2(DATABITS, index);
-    else
-        regData = RTL8367C_ACLRULETBADDR(DATABITS, index);
-    retVal = rtl8367c_setAsicReg(regAddr,regData);
-    if(retVal !=RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_TABLE_ACCESS_WRDATA_REG(RTL8367C_ACLRULETBLEN), 0x1, 0);
-    if(retVal !=RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_WRITE, TB_TARGET_ACLRULE);
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal !=RT_ERR_OK)
-        return retVal;
-
-
-
-    /* Write ACS_ADR register */
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    if(index >= 64)
-        regData = RTL8367C_ACLRULETBADDR2(CAREBITS, index);
-    else
-        regData = RTL8367C_ACLRULETBADDR(CAREBITS, index);
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write Care Bits to ACS_DATA registers */
-     tableAddr = (rtk_uint16*)&aclRuleSmi.care_bits;
-     regAddr = RTL8367C_TABLE_ACCESS_WRDATA_BASE;
-
-    for(i = 0; i < RTL8367C_ACLRULETBLEN; i++)
-    {
-        regData = *tableAddr;
-        retVal = rtl8367c_setAsicReg(regAddr, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        regAddr++;
-        tableAddr++;
-    }
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_TABLE_ACCESS_WRDATA_REG(RTL8367C_ACLRULETBLEN), (0x0007 << 1), (aclRuleSmi.care_bits_ext.rule_info >> 1) & 0x0007);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write ACS_CMD register */
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_WRITE, TB_TARGET_ACLRULE);
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK,regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-
-
-    /* Write ACS_ADR register for data bits */
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    if(index >= 64)
-        regData = RTL8367C_ACLRULETBADDR2(DATABITS, index);
-    else
-        regData = RTL8367C_ACLRULETBADDR(DATABITS, index);
-
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write Data Bits to ACS_DATA registers */
-     tableAddr = (rtk_uint16*)&aclRuleSmi.data_bits;
-     regAddr = RTL8367C_TABLE_ACCESS_WRDATA_BASE;
-
-    for(i = 0; i < RTL8367C_ACLRULETBLEN; i++)
-    {
-        regData = *tableAddr;
-        retVal = rtl8367c_setAsicReg(regAddr, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        regAddr++;
-        tableAddr++;
-    }
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_TABLE_ACCESS_WRDATA_REG(RTL8367C_ACLRULETBLEN), 0, aclRuleSmi.valid);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_TABLE_ACCESS_WRDATA_REG(RTL8367C_ACLRULETBLEN), (0x0007 << 1), (aclRuleSmi.data_bits_ext.rule_info >> 1) & 0x0007);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write ACS_CMD register for care bits*/
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_WRITE, TB_TARGET_ACLRULE);
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-#ifdef CONFIG_RTL8367C_ASICDRV_TEST
-    memcpy(&Rtl8370sVirtualAclRuleTable[index], &aclRuleSmi, sizeof(rtl8367c_aclrulesmi));
-#endif
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicAclRule
- * Description:
- *      Get acl rule content
- * Input:
- *      index   - ACL rule index (0-63) of 64 ACL rules
- *      pAclRule - ACL rule stucture for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-63)
-  * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclRule(rtk_uint32 index, rtl8367c_aclrule *pAclRule)
-{
-    rtl8367c_aclrulesmi aclRuleSmi;
-    rtk_uint32 regAddr, regData;
-    ret_t retVal;
-    rtk_uint16* tableAddr;
-    rtk_uint32 i;
-
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    memset(&aclRuleSmi, 0x00, sizeof(rtl8367c_aclrulesmi));
-
-    /* Write ACS_ADR register for data bits */
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    if(index >= 64)
-        regData = RTL8367C_ACLRULETBADDR2(DATABITS, index);
-    else
-        regData = RTL8367C_ACLRULETBADDR(DATABITS, index);
-
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-
-    /* Write ACS_CMD register */
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_READ, TB_TARGET_ACLRULE);
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Read Data Bits */
-    regAddr = RTL8367C_TABLE_ACCESS_RDDATA_BASE;
-    tableAddr = (rtk_uint16*)&aclRuleSmi.data_bits;
-    for(i = 0; i < RTL8367C_ACLRULETBLEN; i++)
-    {
-        retVal = rtl8367c_getAsicReg(regAddr, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *tableAddr = regData;
-
-        regAddr ++;
-        tableAddr ++;
-    }
-
-    /* Read Valid Bit */
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_RDDATA_REG(RTL8367C_ACLRULETBLEN), 0, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    aclRuleSmi.valid = regData & 0x1;
-    /* Read active_portmsk_ext Bits */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_TABLE_ACCESS_RDDATA_REG(RTL8367C_ACLRULETBLEN), 0x7<<1, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    aclRuleSmi.data_bits_ext.rule_info = (regData % 0x0007) << 1;
-
-
-    /* Write ACS_ADR register for carebits*/
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    if(index >= 64)
-        regData = RTL8367C_ACLRULETBADDR2(CAREBITS, index);
-    else
-        regData = RTL8367C_ACLRULETBADDR(CAREBITS, index);
-
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write ACS_CMD register */
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_READ, TB_TARGET_ACLRULE);
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Read Care Bits */
-    regAddr = RTL8367C_TABLE_ACCESS_RDDATA_BASE;
-    tableAddr = (rtk_uint16*)&aclRuleSmi.care_bits;
-    for(i = 0; i < RTL8367C_ACLRULETBLEN; i++)
-    {
-        retVal = rtl8367c_getAsicReg(regAddr, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *tableAddr = regData;
-
-        regAddr ++;
-        tableAddr ++;
-    }
-    /* Read active_portmsk_ext care Bits */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_TABLE_ACCESS_RDDATA_REG(RTL8367C_ACLRULETBLEN), 0x7<<1, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    aclRuleSmi.care_bits_ext.rule_info = (regData & 0x0007) << 1;
-
-#ifdef CONFIG_RTL8367C_ASICDRV_TEST
-    memcpy(&aclRuleSmi,&Rtl8370sVirtualAclRuleTable[index], sizeof(rtl8367c_aclrulesmi));
-#endif
-
-     _rtl8367c_aclRuleStSmi2User(pAclRule, &aclRuleSmi);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicAclNot
- * Description:
- *      Set rule comparison result inversion / no inversion
- * Input:
- *      index   - ACL rule index (0-95) of 96 ACL rules
- *      not     - 1: inverse, 0: don't inverse
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-95)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAclNot(rtk_uint32 index, rtk_uint32 not)
-{
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(index < 64)
-        return rtl8367c_setAsicRegBit(RTL8367C_ACL_ACTION_CTRL_REG(index), RTL8367C_ACL_OP_NOT_OFFSET(index), not);
-    else
-        return rtl8367c_setAsicRegBit(RTL8367C_ACL_ACTION_CTRL2_REG(index), RTL8367C_ACL_OP_NOT_OFFSET(index), not);
-
-}
-/* Function Name:
- *      rtl8367c_getAsicAcl
- * Description:
- *      Get rule comparison result inversion / no inversion
- * Input:
- *      index   - ACL rule index (0-95) of 95 ACL rules
- *      pNot    - 1: inverse, 0: don't inverse
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-95)
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclNot(rtk_uint32 index, rtk_uint32* pNot)
-{
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(index < 64)
-        return rtl8367c_getAsicRegBit(RTL8367C_ACL_ACTION_CTRL_REG(index), RTL8367C_ACL_OP_NOT_OFFSET(index), pNot);
-    else
-        return rtl8367c_getAsicRegBit(RTL8367C_ACL_ACTION_CTRL2_REG(index), RTL8367C_ACL_OP_NOT_OFFSET(index), pNot);
-
-}
-/* Function Name:
- *      rtl8367c_setAsicAclTemplate
- * Description:
- *      Set fields of a ACL Template
- * Input:
- *      index   - ACL template index(0~4)
- *      pAclType - ACL type stucture for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL template index(0~4)
- * Note:
- *      The API can set type field of the 5 ACL rule templates.
- *      Each type has 8 fields. One field means what data in one field of a ACL rule means
- *      8 fields of ACL rule 0~95 is descripted by one type in ACL group
- */
-ret_t rtl8367c_setAsicAclTemplate(rtk_uint32 index, rtl8367c_acltemplate_t* pAclType)
-{
-    ret_t retVal;
-    rtk_uint32 i;
-    rtk_uint32 regAddr, regData;
-
-    if(index >= RTL8367C_ACLTEMPLATENO)
-        return RT_ERR_OUT_OF_RANGE;
-
-    regAddr = RTL8367C_ACL_RULE_TEMPLATE_CTRL_REG(index);
-
-    for(i = 0; i < (RTL8367C_ACLRULEFIELDNO/2); i++)
-    {
-        regData = pAclType->field[i*2+1];
-        regData = regData << 8 | pAclType->field[i*2];
-
-        retVal = rtl8367c_setAsicReg(regAddr + i, regData);
-
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicAclTemplate
- * Description:
- *      Get fields of a ACL Template
- * Input:
- *      index   - ACL template index(0~4)
- *      pAclType - ACL type stucture for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL template index(0~4)
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclTemplate(rtk_uint32 index, rtl8367c_acltemplate_t *pAclType)
-{
-    ret_t retVal;
-    rtk_uint32 i;
-    rtk_uint32 regData, regAddr;
-
-    if(index >= RTL8367C_ACLTEMPLATENO)
-        return RT_ERR_OUT_OF_RANGE;
-
-    regAddr = RTL8367C_ACL_RULE_TEMPLATE_CTRL_REG(index);
-
-    for(i = 0; i < (RTL8367C_ACLRULEFIELDNO/2); i++)
-    {
-        retVal = rtl8367c_getAsicReg(regAddr + i,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        pAclType->field[i*2] = regData & 0xFF;
-        pAclType->field[i*2 + 1] = (regData >> 8) & 0xFF;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicAclAct
- * Description:
- *      Set ACL rule matched Action
- * Input:
- *      index   - ACL rule index (0-95) of 96 ACL rules
- *      pAclAct     - ACL action stucture for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-95)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAclAct(rtk_uint32 index, rtl8367c_acl_act_t* pAclAct)
-{
-    rtk_uint16 aclActSmi[RTL8367C_ACL_ACT_TABLE_LEN];
-    ret_t retVal;
-    rtk_uint32 regAddr, regData;
-    rtk_uint16* tableAddr;
-    rtk_uint32 i;
-
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    memset(aclActSmi, 0x00, sizeof(rtk_uint16) * RTL8367C_ACL_ACT_TABLE_LEN);
-     _rtl8367c_aclActStUser2Smi(pAclAct, aclActSmi);
-
-    /* Write ACS_ADR register for data bits */
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    regData = index;
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write Data Bits to ACS_DATA registers */
-     tableAddr = aclActSmi;
-     regAddr = RTL8367C_TABLE_ACCESS_WRDATA_BASE;
-
-    for(i = 0; i < RTL8367C_ACLACTTBLEN; i++)
-    {
-        regData = *tableAddr;
-        retVal = rtl8367c_setAsicReg(regAddr, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        regAddr++;
-        tableAddr++;
-    }
-
-    /* Write ACS_CMD register for care bits*/
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_WRITE, TB_TARGET_ACLACT);
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-#ifdef CONFIG_RTL8367C_ASICDRV_TEST
-    memcpy(&Rtl8370sVirtualAclActTable[index][0], aclActSmi, sizeof(rtk_uint16) * RTL8367C_ACL_ACT_TABLE_LEN);
-#endif
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicAclAct
- * Description:
- *      Get ACL rule matched Action
- * Input:
- *      index   - ACL rule index (0-95) of 96 ACL rules
- *      pAclAct     - ACL action stucture for setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-95)
-  * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclAct(rtk_uint32 index, rtl8367c_acl_act_t *pAclAct)
-{
-    rtk_uint16 aclActSmi[RTL8367C_ACL_ACT_TABLE_LEN];
-    ret_t retVal;
-    rtk_uint32 regAddr, regData;
-    rtk_uint16 *tableAddr;
-    rtk_uint32 i;
-
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    memset(aclActSmi, 0x00, sizeof(rtk_uint16) * RTL8367C_ACL_ACT_TABLE_LEN);
-
-    /* Write ACS_ADR register for data bits */
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    regData = index;
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write ACS_CMD register */
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_READ, TB_TARGET_ACLACT);
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Read Data Bits */
-    regAddr = RTL8367C_TABLE_ACCESS_RDDATA_BASE;
-    tableAddr = aclActSmi;
-    for(i = 0; i < RTL8367C_ACLACTTBLEN; i++)
-    {
-        retVal = rtl8367c_getAsicReg(regAddr, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *tableAddr = regData;
-
-        regAddr ++;
-        tableAddr ++;
-    }
-
-#ifdef CONFIG_RTL8367C_ASICDRV_TEST
-    memcpy(aclActSmi, &Rtl8370sVirtualAclActTable[index][0], sizeof(rtk_uint16) * RTL8367C_ACL_ACT_TABLE_LEN);
-#endif
-
-     _rtl8367c_aclActStSmi2User(pAclAct, aclActSmi);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicAclActCtrl
- * Description:
- *      Set ACL rule matched Action Control Bits
- * Input:
- *      index       - ACL rule index (0-95) of 96 ACL rules
- *      aclActCtrl  - 6 ACL Control Bits
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-95)
- * Note:
- *      ACL Action Control Bits Indicate which actions will be take when a rule matches
- */
-ret_t rtl8367c_setAsicAclActCtrl(rtk_uint32 index, rtk_uint32 aclActCtrl)
-{
-    ret_t retVal;
-
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(index >= 64)
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_ACL_ACTION_CTRL2_REG(index), RTL8367C_ACL_OP_ACTION_MASK(index), aclActCtrl);
-    else
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_ACL_ACTION_CTRL_REG(index), RTL8367C_ACL_OP_ACTION_MASK(index), aclActCtrl);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicAclActCtrl
- * Description:
- *      Get ACL rule matched Action Control Bits
- * Input:
- *      index       - ACL rule index (0-95) of 96 ACL rules
- *      pAclActCtrl     - 6 ACL Control Bits
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL rule index (0-95)
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclActCtrl(rtk_uint32 index, rtk_uint32 *pAclActCtrl)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    if(index > RTL8367C_ACLRULEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(index >= 64)
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_ACL_ACTION_CTRL2_REG(index), RTL8367C_ACL_OP_ACTION_MASK(index), &regData);
-    else
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_ACL_ACTION_CTRL_REG(index), RTL8367C_ACL_OP_ACTION_MASK(index), &regData);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pAclActCtrl = regData;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicAclPortRange
- * Description:
- *      Set ACL TCP/UDP range check
- * Input:
- *      index       - TCP/UDP port range check table index
- *      type        - Range check type
- *      upperPort   - TCP/UDP port range upper bound
- *      lowerPort   - TCP/UDP port range lower bound
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid TCP/UDP port range check table index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAclPortRange(rtk_uint32 index, rtk_uint32 type, rtk_uint32 upperPort, rtk_uint32 lowerPort)
-{
-    ret_t retVal;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL2 + index*3, RTL8367C_ACL_SDPORT_RANGE_ENTRY0_CTRL2_MASK, type);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL1 + index*3, upperPort);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL0 + index*3, lowerPort);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicAclPortRange
- * Description:
- *      Get ACL TCP/UDP range check
- * Input:
- *      index       - TCP/UDP port range check table index
- *      pType       - Range check type
- *      pUpperPort  - TCP/UDP port range upper bound
- *      pLowerPort  - TCP/UDP port range lower bound
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid TCP/UDP port range check table index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclPortRange(rtk_uint32 index, rtk_uint32* pType, rtk_uint32* pUpperPort, rtk_uint32* pLowerPort)
-{
-    ret_t retVal;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL2 + index*3, RTL8367C_ACL_SDPORT_RANGE_ENTRY0_CTRL2_MASK, pType);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL1 + index*3, pUpperPort);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_SDPORT_RANGE_ENTRY0_CTRL0 + index*3, pLowerPort);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicAclVidRange
- * Description:
- *      Set ACL VID range check
- * Input:
- *      index       - ACL VID range check index(0~15)
- *      type        - Range check type
- *      upperVid    - VID range upper bound
- *      lowerVid    - VID range lower bound
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL  VID range check index(0~15)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAclVidRange(rtk_uint32 index, rtk_uint32 type, rtk_uint32 upperVid, rtk_uint32 lowerVid)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    regData = ((type << RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_TYPE_OFFSET) & RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_TYPE_MASK) |
-                (upperVid & RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_HIGH_MASK);
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_VID_RANGE_ENTRY0_CTRL1 + index*2, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_VID_RANGE_ENTRY0_CTRL0 + index*2, lowerVid);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicAclVidRange
- * Description:
- *      Get ACL VID range check
- * Input:
- *      index       - ACL VID range check index(0~15)
- *      pType       - Range check type
- *      pUpperVid   - VID range upper bound
- *      pLowerVid   - VID range lower bound
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL VID range check index(0~15)
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclVidRange(rtk_uint32 index, rtk_uint32* pType, rtk_uint32* pUpperVid, rtk_uint32* pLowerVid)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_VID_RANGE_ENTRY0_CTRL1 + index*2, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pType = (regData & RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_TYPE_MASK) >> RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_TYPE_OFFSET;
-    *pUpperVid = regData & RTL8367C_ACL_VID_RANGE_ENTRY0_CTRL1_CHECK0_HIGH_MASK;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_VID_RANGE_ENTRY0_CTRL0 + index*2, pLowerVid);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicAclIpRange
- * Description:
- *      Set ACL IP range check
- * Input:
- *      index       - ACL IP range check index(0~15)
- *      type        - Range check type
- *      upperIp     - IP range upper bound
- *      lowerIp     - IP range lower bound
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL IP range check index(0~15)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAclIpRange(rtk_uint32 index, rtk_uint32 type, ipaddr_t upperIp, ipaddr_t lowerIp)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    ipaddr_t ipData;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL4 + index*5, RTL8367C_ACL_IP_RANGE_ENTRY0_CTRL4_MASK, type);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    ipData = upperIp;
-
-    regData = ipData & 0xFFFF;
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL2 + index*5, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regData = (ipData>>16) & 0xFFFF;
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL3 + index*5, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    ipData = lowerIp;
-
-    regData = ipData & 0xFFFF;
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL0 + index*5, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regData = (ipData>>16) & 0xFFFF;
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL1 + index*5, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicAclIpRange
- * Description:
- *      Get ACL IP range check
- * Input:
- *      index       - ACL IP range check index(0~15)
- *      pType       - Range check type
- *      pUpperIp    - IP range upper bound
- *      pLowerIp    - IP range lower bound
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Invalid ACL IP range check index(0~15)
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAclIpRange(rtk_uint32 index, rtk_uint32* pType, ipaddr_t* pUpperIp, ipaddr_t* pLowerIp)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    ipaddr_t ipData;
-
-    if(index > RTL8367C_ACLRANGEMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL4 + index*5, RTL8367C_ACL_IP_RANGE_ENTRY0_CTRL4_MASK, pType);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL2 + index*5, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    ipData = regData;
-
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL3 + index*5, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    ipData = (regData <<16) | ipData;
-    *pUpperIp = ipData;
-
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL0 + index*5, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    ipData = regData;
-
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_ACL_IP_RANGE_ENTRY0_CTRL1 + index*5, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    ipData = (regData << 16) | ipData;
-    *pLowerIp = ipData;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicAclGpioPolarity
- * Description:
- *      Set ACL Goip control palarity
- * Input:
- *      polarity - 1: High, 0: Low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      none
- */
-ret_t rtl8367c_setAsicAclGpioPolarity(rtk_uint32 polarity)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_ACL_GPIO_POLARITY, RTL8367C_ACL_GPIO_POLARITY_OFFSET, polarity);
-}
-/* Function Name:
- *      rtl8367c_getAsicAclGpioPolarity
- * Description:
- *      Get ACL Goip control palarity
- * Input:
- *      pPolarity - 1: High, 0: Low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      none
- */
-ret_t rtl8367c_getAsicAclGpioPolarity(rtk_uint32* pPolarity)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_ACL_GPIO_POLARITY, RTL8367C_ACL_GPIO_POLARITY_OFFSET, pPolarity);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_cputag.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_cputag.c
deleted file mode 100644
index d22bf65eaa..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_cputag.c
+++ /dev/null
@@ -1,369 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Proprietary CPU-tag related function drivers
- *
- */
-#include <rtl8367c_asicdrv_cputag.h>
-/* Function Name:
- *      rtl8367c_setAsicCputagEnable
- * Description:
- *      Set cpu tag function enable/disable
- * Input:
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_ENABLE   - Invalid enable/disable input
- * Note:
- *      If CPU tag function is disabled, CPU tag will not be added to frame
- *      forwarded to CPU port, and all ports cannot parse CPU tag.
- */
-ret_t rtl8367c_setAsicCputagEnable(rtk_uint32 enabled)
-{
-    if(enabled > 1)
-        return RT_ERR_ENABLE;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_EN_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagEnable
- * Description:
- *      Get cpu tag function enable/disable
- * Input:
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicCputagEnable(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_EN_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicCputagTrapPort
- * Description:
- *      Set cpu tag trap port
- * Input:
- *      port - port number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *     API can set destination port of trapping frame
- */
-ret_t rtl8367c_setAsicCputagTrapPort(rtk_uint32 port)
-{
-    ret_t retVal;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TRAP_PORT_MASK, port & 7);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TRAP_PORT_EXT_MASK, (port>>3) & 1);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagTrapPort
- * Description:
- *      Get cpu tag trap port
- * Input:
- *      pPort - port number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *     None
- */
-ret_t rtl8367c_getAsicCputagTrapPort(rtk_uint32 *pPort)
-{
-    ret_t retVal;
-    rtk_uint32 tmpPort;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TRAP_PORT_MASK, &tmpPort);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPort = tmpPort;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TRAP_PORT_EXT_MASK, &tmpPort);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPort |= (tmpPort & 1) << 3;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicCputagPortmask
- * Description:
- *      Set ports that can parse CPU tag
- * Input:
- *      portmask - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *     None
- */
-ret_t rtl8367c_setAsicCputagPortmask(rtk_uint32 portmask)
-{
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicReg(RTL8367C_CPU_PORT_MASK_REG, portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagPortmask
- * Description:
- *      Get ports that can parse CPU tag
- * Input:
- *      pPortmask - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *     None
- */
-ret_t rtl8367c_getAsicCputagPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_CPU_PORT_MASK_REG, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicCputagInsertMode
- * Description:
- *      Set CPU-tag insert mode
- * Input:
- *      mode - 0: insert to all packets; 1: insert to trapped packets; 2: don't insert
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NOT_ALLOWED  - Actions not allowed by the function
- * Note:
- *     None
- */
-ret_t rtl8367c_setAsicCputagInsertMode(rtk_uint32 mode)
-{
-    if(mode >= CPUTAG_INSERT_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_INSERTMODE_MASK, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagInsertMode
- * Description:
- *      Get CPU-tag insert mode
- * Input:
- *      pMode - 0: insert to all packets; 1: insert to trapped packets; 2: don't insert
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *     None
- */
-ret_t rtl8367c_getAsicCputagInsertMode(rtk_uint32 *pMode)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_INSERTMODE_MASK, pMode);
-}
-/* Function Name:
- *      rtl8367c_setAsicCputagPriorityRemapping
- * Description:
- *      Set queue assignment of CPU port
- * Input:
- *      srcPri - internal priority (0~7)
- *      newPri - internal priority after remapping (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY     - Invalid priority
- * Note:
- *     None
- */
-ret_t rtl8367c_setAsicCputagPriorityRemapping(rtk_uint32 srcPri, rtk_uint32 newPri)
-{
-    if((srcPri > RTL8367C_PRIMAX) || (newPri > RTL8367C_PRIMAX))
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_REG(srcPri), RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_MASK(srcPri), newPri);
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagPriorityRemapping
- * Description:
- *      Get queue assignment of CPU port
- * Input:
- *      srcPri - internal priority (0~7)
- *      pNewPri - internal priority after remapping (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY     - Invalid priority
- * Note:
- *     None
- */
-ret_t rtl8367c_getAsicCputagPriorityRemapping(rtk_uint32 srcPri, rtk_uint32 *pNewPri)
-{
-    if(srcPri > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_REG(srcPri), RTL8367C_QOS_PRIPORITY_REMAPPING_IN_CPU_MASK(srcPri), pNewPri);
-}
-/* Function Name:
- *      rtl8367c_setAsicCputagPosition
- * Description:
- *      Set cpu tag insert position
- * Input:
- *      postion - 1: After entire packet(before CRC field), 0: After MAC_SA (Default)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *     None
- */
-ret_t rtl8367c_setAsicCputagPosition(rtk_uint32 postion)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TAG_POSITION_OFFSET, postion);
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagPosition
- * Description:
- *      Get cpu tag insert position
- * Input:
- *      pPostion - 1: After entire packet(before CRC field), 0: After MAC_SA (Default)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *     None
- */
-ret_t rtl8367c_getAsicCputagPosition(rtk_uint32* pPostion)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TAG_POSITION_OFFSET, pPostion);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicCputagMode
- * Description:
- *      Set cpu tag mode
- * Input:
- *      mode - 1: 4bytes mode, 0: 8bytes mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameters
- * Note:
- *      If CPU tag function is disabled, CPU tag will not be added to frame
- *      forwarded to CPU port, and all ports cannot parse CPU tag.
- */
-ret_t rtl8367c_setAsicCputagMode(rtk_uint32 mode)
-{
-    if(mode > 1)
-        return RT_ERR_INPUT;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TAG_FORMAT_OFFSET, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagMode
- * Description:
- *      Get cpu tag mode
- * Input:
- *      pMode - 1: 4bytes mode, 0: 8bytes mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicCputagMode(rtk_uint32 *pMode)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TAG_FORMAT_OFFSET, pMode);
-}
-/* Function Name:
- *      rtl8367c_setAsicCputagRxMinLength
- * Description:
- *      Set cpu tag mode
- * Input:
- *      mode - 1: 64bytes, 0: 72bytes
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameters
- * Note:
- *      If CPU tag function is disabled, CPU tag will not be added to frame
- *      forwarded to CPU port, and all ports cannot parse CPU tag.
- */
-ret_t rtl8367c_setAsicCputagRxMinLength(rtk_uint32 mode)
-{
-    if(mode > 1)
-        return RT_ERR_INPUT;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TAG_RXBYTECOUNT_OFFSET, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicCputagRxMinLength
- * Description:
- *      Get cpu tag mode
- * Input:
- *      pMode - 1: 64bytes, 0: 72bytes
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicCputagRxMinLength(rtk_uint32 *pMode)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_CPU_CTRL, RTL8367C_CPU_TAG_RXBYTECOUNT_OFFSET, pMode);
-}
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_dot1x.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_dot1x.c
deleted file mode 100644
index 73153e177e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_dot1x.c
+++ /dev/null
@@ -1,415 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : 802.1X related functions
- *
- */
-#include <rtl8367c_asicdrv_dot1x.h>
-/* Function Name:
- *      rtl8367c_setAsic1xPBEnConfig
- * Description:
- *      Set 802.1x port-based port enable configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xPBEnConfig(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_DOT1X_PORT_ENABLE_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xPBEnConfig
- * Description:
- *      Get 802.1x port-based port enable configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xPBEnConfig(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_DOT1X_PORT_ENABLE_REG, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xPBAuthConfig
- * Description:
- *      Set 802.1x port-based authorised port configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      auth    - 1: authorised, 0: non-authorised
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xPBAuthConfig(rtk_uint32 port, rtk_uint32 auth)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_DOT1X_PORT_AUTH_REG, port, auth);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xPBAuthConfig
- * Description:
- *      Get 802.1x port-based authorised port configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      pAuth   - 1: authorised, 0: non-authorised
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xPBAuthConfig(rtk_uint32 port, rtk_uint32 *pAuth)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_DOT1X_PORT_AUTH_REG, port, pAuth);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xPBOpdirConfig
- * Description:
- *      Set 802.1x port-based operational direction
- * Input:
- *      port    - Physical port number (0~7)
- *      opdir   - Operation direction 1: IN, 0:BOTH
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xPBOpdirConfig(rtk_uint32 port, rtk_uint32 opdir)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_DOT1X_PORT_OPDIR_REG, port, opdir);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xPBOpdirConfig
- * Description:
- *      Get 802.1x port-based operational direction
- * Input:
- *      port    - Physical port number (0~7)
- *      pOpdir  - Operation direction 1: IN, 0:BOTH
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xPBOpdirConfig(rtk_uint32 port, rtk_uint32* pOpdir)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_DOT1X_PORT_OPDIR_REG, port, pOpdir);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xMBEnConfig
- * Description:
- *      Set 802.1x mac-based port enable configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xMBEnConfig(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_DOT1X_MAC_ENABLE_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xMBEnConfig
- * Description:
- *      Get 802.1x mac-based port enable configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xMBEnConfig(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_DOT1X_MAC_ENABLE_REG, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xMBOpdirConfig
- * Description:
- *      Set 802.1x mac-based operational direction
- * Input:
- *      opdir       - Operation direction 1: IN, 0:BOTH
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xMBOpdirConfig(rtk_uint32 opdir)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_DOT1X_CFG_REG, RTL8367C_DOT1X_MAC_OPDIR_OFFSET, opdir);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xMBOpdirConfig
- * Description:
- *      Get 802.1x mac-based operational direction
- * Input:
- *      pOpdir      - Operation direction 1: IN, 0:BOTH
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xMBOpdirConfig(rtk_uint32 *pOpdir)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_DOT1X_CFG_REG, RTL8367C_DOT1X_MAC_OPDIR_OFFSET, pOpdir);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xProcConfig
- * Description:
- *      Set 802.1x unauth. behavior configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      proc    - 802.1x unauth. behavior configuration 0:drop 1:trap to CPU 2:Guest VLAN
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_DOT1X_PROC   - Unauthorized behavior error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xProcConfig(rtk_uint32 port, rtk_uint32 proc)
-{
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(proc >= DOT1X_UNAUTH_END)
-        return RT_ERR_DOT1X_PROC;
-
-    if(port < 8)
-    {
-        return rtl8367c_setAsicRegBits(RTL8367C_DOT1X_UNAUTH_ACT_BASE, RTL8367C_DOT1X_UNAUTH_ACT_MASK(port),proc);
-    }
-    else
-    {
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_DOT1X_UNAUTH_ACT_W1, RTL8367C_DOT1X_UNAUTH_ACT_MASK(port),proc);
-    }
-}
-/* Function Name:
- *      rtl8367c_getAsic1xProcConfig
- * Description:
- *      Get 802.1x unauth. behavior configuration
- * Input:
- *      port    - Physical port number (0~7)
- *      pProc   - 802.1x unauth. behavior configuration 0:drop 1:trap to CPU 2:Guest VLAN
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xProcConfig(rtk_uint32 port, rtk_uint32* pProc)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    return rtl8367c_getAsicRegBits(RTL8367C_DOT1X_UNAUTH_ACT_BASE, RTL8367C_DOT1X_UNAUTH_ACT_MASK(port),pProc);
-    else
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_DOT1X_UNAUTH_ACT_W1, RTL8367C_DOT1X_UNAUTH_ACT_MASK(port),pProc);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xGuestVidx
- * Description:
- *      Set 802.1x guest vlan index
- * Input:
- *      index   - 802.1x guest vlan index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_DOT1X_GVLANIDX   - Invalid cvid index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xGuestVidx(rtk_uint32 index)
-{
-    if(index >= RTL8367C_CVIDXNO)
-        return RT_ERR_DOT1X_GVLANIDX;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_DOT1X_CFG_REG, RTL8367C_DOT1X_GVIDX_MASK, index);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xGuestVidx
- * Description:
- *      Get 802.1x guest vlan index
- * Input:
- *      pIndex  - 802.1x guest vlan index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xGuestVidx(rtk_uint32 *pIndex)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_DOT1X_CFG_REG, RTL8367C_DOT1X_GVIDX_MASK, pIndex);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xGVOpdir
- * Description:
- *      Set 802.1x guest vlan talk to auth. DA
- * Input:
- *      enabled     - 0:disable 1:enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xGVOpdir(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_DOT1X_CFG_REG, RTL8367C_DOT1X_GVOPDIR_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xGVOpdir
- * Description:
- *      Get 802.1x guest vlan talk to auth. DA
- * Input:
- *      pEnabled        - 0:disable 1:enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xGVOpdir(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_DOT1X_CFG_REG, RTL8367C_DOT1X_GVOPDIR_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsic1xTrapPriority
- * Description:
- *      Set 802.1x Trap priority
- * Input:
- *      priority    - priority (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsic1xTrapPriority(rtk_uint32 priority)
-{
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_QOS_TRAP_PRIORITY0, RTL8367C_DOT1X_PRIORTY_MASK,priority);
-}
-/* Function Name:
- *      rtl8367c_getAsic1xTrapPriority
- * Description:
- *      Get 802.1x Trap priority
- * Input:
- *      pPriority   - priority (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsic1xTrapPriority(rtk_uint32 *pPriority)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_QOS_TRAP_PRIORITY0, RTL8367C_DOT1X_PRIORTY_MASK, pPriority);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_eav.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_eav.c
deleted file mode 100644
index 370b7c6f3a..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_eav.c
+++ /dev/null
@@ -1,877 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Ethernet AV related functions
- *
- */
-
-#include <rtl8367c_asicdrv_eav.h>
-/* Function Name:
- *      rtl8367c_setAsicEavMacAddress
- * Description:
- *      Set PTP MAC address
- * Input:
- *      mac     - PTP mac
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicEavMacAddress(ether_addr_t mac)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint8 *accessPtr;
-    rtk_uint32 i;
-
-    accessPtr =  (rtk_uint8*)&mac;
-
-    regData = *accessPtr;
-    accessPtr ++;
-    regData = (regData << 8) | *accessPtr;
-    accessPtr ++;
-    for(i = 0; i <=2; i++)
-    {
-        retVal = rtl8367c_setAsicReg(RTL8367C_REG_MAC_ADDR_H - i, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        regData = *accessPtr;
-        accessPtr ++;
-        regData = (regData << 8) | *accessPtr;
-        accessPtr ++;
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicEavMacAddress
- * Description:
- *      Get PTP MAC address
- * Input:
- *      None
- * Output:
- *      pMac     - PTP  mac
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEavMacAddress(ether_addr_t *pMac)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint8 *accessPtr;
-    rtk_uint32 i;
-
-    accessPtr = (rtk_uint8*)pMac;
-
-    for(i = 0; i <= 2; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_REG_MAC_ADDR_H - i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *accessPtr = (regData & 0xFF00) >> 8;
-        accessPtr ++;
-        *accessPtr = regData & 0xFF;
-        accessPtr ++;
-    }
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicEavTpid
- * Description:
- *      Set PTP parser tag TPID.
- * Input:
- *       outerTag - outter tag TPID
- *       innerTag  - inner tag TPID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *     None
- */
-ret_t rtl8367c_setAsicEavTpid(rtk_uint32 outerTag, rtk_uint32 innerTag)
-{
-    ret_t retVal;
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_OTAG_TPID, outerTag)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_ITAG_TPID, innerTag)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicEavTpid
- * Description:
- *      Get PTP parser tag TPID.
- * Input:
- *      None
- * Output:
- *       pOuterTag - outter tag TPID
- *       pInnerTag  - inner tag TPID
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEavTpid(rtk_uint32* pOuterTag, rtk_uint32* pInnerTag)
-{
-    ret_t retVal;
-
-    if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_OTAG_TPID, pOuterTag)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_ITAG_TPID, pInnerTag)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicEavSysTime
- * Description:
- *      Set PTP system time
- * Input:
- *      second - seconds
- *      nanoSecond - nano seconds
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      The time granuality is 8 nano seconds.
- */
-ret_t rtl8367c_setAsicEavSysTime(rtk_uint32 second, rtk_uint32 nanoSecond)
-{
-    ret_t retVal;
-    rtk_uint32 sec_h, sec_l, nsec8_h, nsec8_l;
-    rtk_uint32 nano_second_8;
-    rtk_uint32 regData, busyFlag, count;
-
-    if(nanoSecond > RTL8367C_EAV_NANOSECONDMAX)
-        return RT_ERR_INPUT;
-
-    regData = 0;
-    sec_h = second >>16;
-    sec_l = second & 0xFFFF;
-    nano_second_8 = nanoSecond >> 3;
-    nsec8_h = (nano_second_8 >>16) & RTL8367C_PTP_TIME_NSEC_H_NSEC_MASK;
-    nsec8_l = nano_second_8 &0xFFFF;
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_SEC_H_SEC, sec_h)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_SEC_L_SEC, sec_l)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_NSEC_L_NSEC, nsec8_l)) != RT_ERR_OK)
-        return retVal;
-
-    regData = nsec8_h | (PTP_TIME_WRITE<<RTL8367C_PTP_TIME_NSEC_H_CMD_OFFSET) | RTL8367C_PTP_TIME_NSEC_H_EXEC_MASK;
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_NSEC_H_NSEC, regData)) != RT_ERR_OK)
-        return retVal;
-
-    count = 0;
-    do {
-        if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_PTP_TIME_NSEC_H_NSEC, RTL8367C_PTP_TIME_NSEC_H_EXEC_OFFSET, &busyFlag)) != RT_ERR_OK)
-            return retVal;
-        count++;
-    } while ((busyFlag != 0)&&(count<5));
-
-    if (busyFlag != 0)
-        return RT_ERR_BUSYWAIT_TIMEOUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicEavSysTime
- * Description:
- *      Get PTP system time
- * Input:
- *      None
- * Output:
- *      second - seconds
- *      nanoSecond - nano seconds
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      The time granuality is 8 nano seconds.
- */
-ret_t rtl8367c_getAsicEavSysTime(rtk_uint32* pSecond, rtk_uint32* pNanoSecond)
-{
-    ret_t retVal;
-    rtk_uint32 sec_h, sec_l, nsec8_h, nsec8_l;
-    rtk_uint32 nano_second_8;
-    rtk_uint32 regData, busyFlag, count;
-
-    regData = 0;
-    regData = (PTP_TIME_READ<<RTL8367C_PTP_TIME_NSEC_H_CMD_OFFSET) | RTL8367C_PTP_TIME_NSEC_H_EXEC_MASK;
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_NSEC_H_NSEC, regData)) != RT_ERR_OK)
-        return retVal;
-
-    count = 0;
-    do {
-        if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_PTP_TIME_NSEC_H_NSEC, RTL8367C_PTP_TIME_NSEC_H_EXEC_OFFSET, &busyFlag)) != RT_ERR_OK)
-            return retVal;
-        count++;
-    } while ((busyFlag != 0)&&(count<5));
-
-    if (busyFlag != 0)
-        return RT_ERR_BUSYWAIT_TIMEOUT;
-
-    if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_PTP_TIME_SEC_H_SEC_RD, &sec_h)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_PTP_TIME_SEC_L_SEC_RD, &sec_l)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_PTP_TIME_NSEC_H_NSEC_RD, RTL8367C_PTP_TIME_NSEC_H_NSEC_RD_MASK,&nsec8_h)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_PTP_TIME_NSEC_L_NSEC_RD, &nsec8_l)) != RT_ERR_OK)
-        return retVal;
-
-    *pSecond = (sec_h<<16) | sec_l;
-    nano_second_8 = (nsec8_h<<16) | nsec8_l;
-    *pNanoSecond = nano_second_8<<3;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicEavSysTimeAdjust
- * Description:
- *      Set PTP system time adjust
- * Input:
- *      type - incresae or decrease
- *      second - seconds
- *      nanoSecond - nano seconds
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      Ethernet AV second offset of timer for tuning
- */
-ret_t rtl8367c_setAsicEavSysTimeAdjust(rtk_uint32 type, rtk_uint32 second, rtk_uint32 nanoSecond)
-{
-    ret_t retVal;
-    rtk_uint32 sec_h, sec_l, nsec8_h, nsec8_l;
-    rtk_uint32 nano_second_8;
-    rtk_uint32 regData, busyFlag, count;
-
-    if (type >= PTP_TIME_ADJ_END)
-        return RT_ERR_INPUT;
-    if(nanoSecond > RTL8367C_EAV_NANOSECONDMAX)
-        return RT_ERR_INPUT;
-
-    regData = 0;
-    sec_h = second >>16;
-    sec_l = second & 0xFFFF;
-    nano_second_8 = nanoSecond >> 3;
-    nsec8_h = (nano_second_8 >>16) & RTL8367C_PTP_TIME_NSEC_H_NSEC_MASK;
-    nsec8_l = nano_second_8 &0xFFFF;
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_SEC_H_SEC, sec_h)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_SEC_L_SEC, sec_l)) != RT_ERR_OK)
-        return retVal;
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_NSEC_L_NSEC, nsec8_l)) != RT_ERR_OK)
-        return retVal;
-
-    if (PTP_TIME_ADJ_INC == type)
-        regData = nsec8_h | (PTP_TIME_INC<<RTL8367C_PTP_TIME_NSEC_H_CMD_OFFSET) | RTL8367C_PTP_TIME_NSEC_H_EXEC_MASK;
-    else
-        regData = nsec8_h | (PTP_TIME_DEC<<RTL8367C_PTP_TIME_NSEC_H_CMD_OFFSET) | RTL8367C_PTP_TIME_NSEC_H_EXEC_MASK;
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_NSEC_H_NSEC, regData)) != RT_ERR_OK)
-        return retVal;
-
-    count = 0;
-    do {
-        if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_PTP_TIME_NSEC_H_NSEC, RTL8367C_PTP_TIME_NSEC_H_EXEC_OFFSET, &busyFlag)) != RT_ERR_OK)
-            return retVal;
-        count++;
-    } while ((busyFlag != 0)&&(count<5));
-
-    if (busyFlag != 0)
-        return RT_ERR_BUSYWAIT_TIMEOUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicEavSysTimeCtrl
- * Description:
- *      Set PTP system time control
- * Input:
- *      command - start or stop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicEavSysTimeCtrl(rtk_uint32 control)
-{
-    ret_t  retVal;
-    rtk_uint32 regData;
-
-    if (control>=PTP_TIME_CTRL_END)
-         return RT_ERR_INPUT;
-
-    regData = 0;
-    if (PTP_TIME_CTRL_START == control)
-            regData = RTL8367C_CFG_TIMER_EN_FRC_MASK | RTL8367C_CFG_TIMER_1588_EN_MASK;
-    else
-        regData = 0;
-
-    if((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PTP_TIME_CFG, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicEavSysTimeCtrl
- * Description:
- *      Get PTP system time control
- * Input:
- *      None
- * Output:
- *      pControl - start or stop
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEavSysTimeCtrl(rtk_uint32* pControl)
-{
-    ret_t  retVal;
-    rtk_uint32 regData;
-    rtk_uint32 mask;
-
-    mask = RTL8367C_CFG_TIMER_EN_FRC_MASK | RTL8367C_CFG_TIMER_1588_EN_MASK;
-
-    if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_PTP_TIME_CFG, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if( (regData & mask) == mask)
-        *pControl = PTP_TIME_CTRL_START;
-    else if( (regData & mask) == 0)
-        *pControl = PTP_TIME_CTRL_STOP;
-    else
-        return RT_ERR_NOT_ALLOWED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicEavInterruptMask
- * Description:
- *      Set PTP interrupt enable mask
- * Input:
- *      imr     - Interrupt mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      [0]:TX_SYNC,
- *      [1]:TX_DELAY,
- *      [2]:TX_PDELAY_REQ,
- *      [3]:TX_PDELAY_RESP,
- *      [4]:RX_SYNC,
- *      [5]:RX_DELAY,
- *      [6]:RX_PDELAY_REQ,
- *      [7]:RX_PDELAY_RESP,
- */
-ret_t rtl8367c_setAsicEavInterruptMask(rtk_uint32 imr)
-{
-    if ((imr&(RTL8367C_PTP_INTR_MASK<<8))>0)
-         return RT_ERR_INPUT;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_PTP_TIME_CFG2, RTL8367C_PTP_INTR_MASK, imr);
-}
-/* Function Name:
- *      rtl8367c_getAsicEavInterruptMask
- * Description:
- *      Get PTP interrupt enable mask
- * Input:
- *      pImr    - Interrupt mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      [0]:TX_SYNC,
- *      [1]:TX_DELAY,
- *      [2]:TX_PDELAY_REQ,
- *      [3]:TX_PDELAY_RESP,
- *      [4]:RX_SYNC,
- *      [5]:RX_DELAY,
- *      [6]:RX_PDELAY_REQ,
- *      [7]:RX_PDELAY_RESP,
- */
-ret_t rtl8367c_getAsicEavInterruptMask(rtk_uint32* pImr)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_PTP_TIME_CFG2, RTL8367C_PTP_INTR_MASK, pImr);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicEavInterruptStatus
- * Description:
- *      Get PTP interrupt port status mask
- * Input:
- *      pIms    - Interrupt mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      [0]:p0 interrupt,
- *      [1]:p1 interrupt,
- *      [2]:p2 interrupt,
- *      [3]:p3 interrupt,
- *      [4]:p4 interrupt,
- */
-ret_t rtl8367c_getAsicEavInterruptStatus(rtk_uint32* pIms)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_PTP_INTERRUPT_CFG, RTL8367C_PTP_PORT_MASK, pIms);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicInterruptMask
- * Description:
- *      Clear interrupt enable mask
- * Input:
- *      ims     - Interrupt status mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      This API can be used to clear ASIC interrupt status and register will be cleared by writting 1.
- *      [0]:TX_SYNC,
- *      [1]:TX_DELAY,
- *      [2]:TX_PDELAY_REQ,
- *      [3]:TX_PDELAY_RESP,
- *      [4]:RX_SYNC,
- *      [5]:RX_DELAY,
- *      [6]:RX_PDELAY_REQ,
- *      [7]:RX_PDELAY_RESP,
- */
-ret_t rtl8367c_setAsicEavPortInterruptStatus(rtk_uint32 port, rtk_uint32 ims)
-{
-
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(port < 5)
-        return rtl8367c_setAsicRegBits(RTL8367C_EAV_PORT_CFG_REG(port), RTL8367C_PTP_INTR_MASK,ims);
-    else if(port == 5)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_P5_EAV_CFG, RTL8367C_PTP_INTR_MASK,ims);
-    else if(port == 6)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_P6_EAV_CFG, RTL8367C_PTP_INTR_MASK,ims);
-    else if(port == 7)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_P7_EAV_CFG, RTL8367C_PTP_INTR_MASK,ims);
-    else if(port == 8)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_P8_EAV_CFG, RTL8367C_PTP_INTR_MASK,ims);
-    else if(port == 9)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_P9_EAV_CFG, RTL8367C_PTP_INTR_MASK,ims);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicInterruptStatus
- * Description:
- *      Get interrupt enable mask
- * Input:
- *      pIms    - Interrupt status mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      [0]:TX_SYNC,
- *      [1]:TX_DELAY,
- *      [2]:TX_PDELAY_REQ,
- *      [3]:TX_PDELAY_RESP,
- *      [4]:RX_SYNC,
- *      [5]:RX_DELAY,
- *      [6]:RX_PDELAY_REQ,
- *      [7]:RX_PDELAY_RESP,
- */
-ret_t rtl8367c_getAsicEavPortInterruptStatus(rtk_uint32 port, rtk_uint32* pIms)
-{
-
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-    if(port < 5)
-        return rtl8367c_getAsicRegBits(RTL8367C_EAV_PORT_CFG_REG(port), RTL8367C_PTP_INTR_MASK, pIms);
-    else if(port == 5)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_P5_EAV_CFG, RTL8367C_PTP_INTR_MASK, pIms);
-    else if(port == 6)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_P6_EAV_CFG, RTL8367C_PTP_INTR_MASK,pIms);
-    else if(port == 7)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_P7_EAV_CFG, RTL8367C_PTP_INTR_MASK,pIms);
-    else if(port == 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_P8_EAV_CFG, RTL8367C_PTP_INTR_MASK,pIms);
-    else if(port == 9)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_P9_EAV_CFG, RTL8367C_PTP_INTR_MASK,pIms);
-
-    return RT_ERR_OK;
-
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicEavPortEnable
- * Description:
- *      Set per-port EAV function enable/disable
- * Input:
- *      port         - Physical port number (0~9)
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      If EAV function is enabled, PTP event messgae packet will be attached PTP timestamp for trapping
- */
-ret_t rtl8367c_setAsicEavPortEnable(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(port < 5)
-        return rtl8367c_setAsicRegBit(RTL8367C_EAV_PORT_CFG_REG(port), RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, enabled);
-    else if(port == 5)
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_P5_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, enabled);
-    else if(port == 6)
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_P6_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, enabled);
-    else if(port == 7)
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_P7_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, enabled);
-    else if(port == 8)
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_P8_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, enabled);
-    else if(port == 9)
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_P9_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, enabled);
-
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicEavPortEnable
- * Description:
- *      Get per-port EAV function enable/disable
- * Input:
- *      port         - Physical port number (0~9)
- *      pEnabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEavPortEnable(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-
-
-    if(port < 5)
-        return rtl8367c_getAsicRegBit(RTL8367C_EAV_PORT_CFG_REG(port), RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, pEnabled);
-    else if(port == 5)
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_P5_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, pEnabled);
-    else if(port == 6)
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_P6_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, pEnabled);
-    else if(port == 7)
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_P7_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, pEnabled);
-    else if(port == 8)
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_P8_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, pEnabled);
-    else if(port == 9)
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_P9_EAV_CFG, RTL8367C_EAV_CFG_PTP_PHY_EN_EN_OFFSET, pEnabled);
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicEavPortTimeStamp
- * Description:
- *      Get PTP port time stamp
- * Input:
- *      port         - Physical port number (0~9)
- *      type     -  PTP packet type
- * Output:
- *      timeStamp - seconds
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      The time granuality is 8 nano seconds.
- */
-ret_t rtl8367c_getAsicEavPortTimeStamp(rtk_uint32 port, rtk_uint32 type, rtl8367c_ptp_time_stamp_t* timeStamp)
-{
-    ret_t retVal;
-    rtk_uint32 sec_h, sec_l, nsec8_h, nsec8_l;
-    rtk_uint32 nano_second_8;
-
-    if(port > 9)
-        return RT_ERR_PORT_ID;
-    if(type >= PTP_PKT_TYPE_END)
-        return RT_ERR_INPUT;
-
-    if(port < 5){
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_SEQ_ID(port, type), &timeStamp->sequence_id))!=  RT_ERR_OK)
-            return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_PORT_SEC_H(port) , &sec_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_PORT_SEC_L(port), &sec_l)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_NSEC_H(port) , RTL8367C_PORT_NSEC_H_MASK,&nsec8_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_PORT_NSEC_L(port) , &nsec8_l)) != RT_ERR_OK)
-           return retVal;
-    }else if(port == 5){
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P5_TX_SYNC_SEQ_ID+type, &timeStamp->sequence_id))!=  RT_ERR_OK)
-            return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P5_PORT_SEC_31_16, &sec_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P5_PORT_SEC_15_0, &sec_l)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_P5_PORT_NSEC_26_16 , RTL8367C_PORT_NSEC_H_MASK,&nsec8_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P5_PORT_NSEC_15_0, &nsec8_l)) != RT_ERR_OK)
-           return retVal;
-    }else if(port == 6){
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P6_TX_SYNC_SEQ_ID+type, &timeStamp->sequence_id))!=  RT_ERR_OK)
-            return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P6_PORT_SEC_31_16, &sec_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P6_PORT_SEC_15_0, &sec_l)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_P6_PORT_NSEC_26_16 , RTL8367C_PORT_NSEC_H_MASK,&nsec8_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P6_PORT_NSEC_15_0, &nsec8_l)) != RT_ERR_OK)
-           return retVal;
-    }else if(port == 7){
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P7_TX_SYNC_SEQ_ID+type, &timeStamp->sequence_id))!=  RT_ERR_OK)
-            return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P7_PORT_SEC_31_16, &sec_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P7_PORT_SEC_15_0, &sec_l)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_P7_PORT_NSEC_26_16 , RTL8367C_PORT_NSEC_H_MASK,&nsec8_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P7_PORT_NSEC_15_0, &nsec8_l)) != RT_ERR_OK)
-           return retVal;
-    }else if(port == 8){
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P8_TX_SYNC_SEQ_ID+type, &timeStamp->sequence_id))!=  RT_ERR_OK)
-            return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P8_PORT_SEC_31_16, &sec_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P8_PORT_SEC_15_0, &sec_l)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_P8_PORT_NSEC_26_16 , RTL8367C_PORT_NSEC_H_MASK,&nsec8_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P8_PORT_NSEC_15_0, &nsec8_l)) != RT_ERR_OK)
-           return retVal;
-    }else if(port == 9){
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P9_TX_SYNC_SEQ_ID+type, &timeStamp->sequence_id))!=  RT_ERR_OK)
-            return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P9_PORT_SEC_31_16, &sec_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P9_PORT_SEC_15_0, &sec_l)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_P9_PORT_NSEC_26_16 , RTL8367C_PORT_NSEC_H_MASK,&nsec8_h)) != RT_ERR_OK)
-           return retVal;
-        if((retVal = rtl8367c_getAsicReg(RTL8367C_REG_P9_PORT_NSEC_15_0, &nsec8_l)) != RT_ERR_OK)
-           return retVal;
-    }
-
-    timeStamp->second = (sec_h<<16) | sec_l;
-    nano_second_8 = (nsec8_h<<16) | nsec8_l;
-    timeStamp->nano_second = nano_second_8<<3;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicEavTrap
- * Description:
- *      Set per-port PTP packet trap to CPU
- * Input:
- *      port         - Physical port number (0~5)
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      If EAV trap enabled, switch will trap PTP packet to CPU
- */
-ret_t rtl8367c_setAsicEavTrap(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_PTP_PORT0_CFG1 + (port * 0x20), RTL8367C_PTP_PORT0_CFG1_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicEavTimeSyncEn
- * Description:
- *      Get per-port EPTP packet trap to CPU
- * Input:
- *      port         - Physical port number (0~5)
- *      pEnabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEavTrap(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_PTP_PORT0_CFG1 + (port * 0x20), RTL8367C_PTP_PORT0_CFG1_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicEavEnable
- * Description:
- *      Set per-port EAV function enable/disable
- * Input:
- *      port         - Physical port number (0~5)
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      If EAV function is enabled, PTP event messgae packet will be attached PTP timestamp for trapping
- */
-ret_t rtl8367c_setAsicEavEnable(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_EAV_CTRL0, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicEavEnable
- * Description:
- *      Get per-port EAV function enable/disable
- * Input:
- *      port         - Physical port number (0~5)
- *      pEnabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEavEnable(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port > RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_EAV_CTRL0, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicEavPriRemapping
- * Description:
- *      Set non-EAV streaming priority remapping
- * Input:
- *      srcpriority - Priority value
- *      priority     - Absolute priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                     - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY      - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicEavPriRemapping(rtk_uint32 srcpriority, rtk_uint32 priority)
-{
-    if(srcpriority > RTL8367C_PRIMAX || priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_EAV_PRIORITY_REMAPPING_REG(srcpriority), RTL8367C_EAV_PRIORITY_REMAPPING_MASK(srcpriority),priority);
-}
-/* Function Name:
- *      rtl8367c_getAsicEavPriRemapping
- * Description:
- *      Get non-EAV streaming priority remapping
- * Input:
- *      srcpriority - Priority value
- *      pPriority     - Absolute priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                     - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY      - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEavPriRemapping(rtk_uint32 srcpriority, rtk_uint32 *pPriority)
-{
-    if(srcpriority > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_EAV_PRIORITY_REMAPPING_REG(srcpriority), RTL8367C_EAV_PRIORITY_REMAPPING_MASK(srcpriority),pPriority);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_eee.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_eee.c
deleted file mode 100644
index f4dda6a6ae..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_eee.c
+++ /dev/null
@@ -1,141 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 48989 $
- * $Date: 2014-07-01 15:45:24 +0800 (週二, 01 七月 2014) $
- *
- * Purpose : RTL8370 switch high-level API for RTL8367C
- * Feature :
- *
- */
-
-#include <rtl8367c_asicdrv_eee.h>
-#include <rtl8367c_asicdrv_phy.h>
-
-/*
-@func ret_t | rtl8367c_setAsicEee100M | Set eee force mode function enable/disable.
-@parm rtk_uint32 | port | The port number.
-@parm rtk_uint32 | enabled | 1: enabled, 0: disabled.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input parameter.
-@comm
-    This API set the 100M EEE enable function.
-
-*/
-ret_t rtl8367c_setAsicEee100M(rtk_uint32 port, rtk_uint32 enable)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if (enable > 1)
-        return RT_ERR_INPUT;
-
-    if((retVal = rtl8367c_getAsicPHYOCPReg(port, EEE_OCP_PHY_ADDR, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(enable)
-        regData |= (0x0001 << 1);
-    else
-        regData &= ~(0x0001 << 1);
-
-    if((retVal = rtl8367c_setAsicPHYOCPReg(port, EEE_OCP_PHY_ADDR, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/*
-@func ret_t | rtl8367c_getAsicEee100M | Get 100M eee enable/disable.
-@parm rtk_uint32 | port | The port number.
-@parm rtk_uint32* | enabled | 1: enabled, 0: disabled.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input parameter.
-@comm
-    This API get the 100M EEE function.
-*/
-ret_t rtl8367c_getAsicEee100M(rtk_uint32 port, rtk_uint32 *enable)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if((retVal = rtl8367c_getAsicPHYOCPReg(port, EEE_OCP_PHY_ADDR, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *enable = (regData & (0x0001 << 1)) ? ENABLED : DISABLED;
-    return RT_ERR_OK;
-}
-
-/*
-@func ret_t | rtl8367c_setAsicEeeGiga | Set eee force mode function enable/disable.
-@parm rtk_uint32 | port | The port number.
-@parm rtk_uint32 | enabled | 1: enabled, 0: disabled.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input parameter.
-@comm
-    This API set the 100M EEE enable function.
-
-*/
-ret_t rtl8367c_setAsicEeeGiga(rtk_uint32 port, rtk_uint32 enable)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if (enable > 1)
-        return RT_ERR_INPUT;
-
-    if((retVal = rtl8367c_getAsicPHYOCPReg(port, EEE_OCP_PHY_ADDR, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(enable)
-        regData |= (0x0001 << 2);
-    else
-        regData &= ~(0x0001 << 2);
-
-    if((retVal = rtl8367c_setAsicPHYOCPReg(port, EEE_OCP_PHY_ADDR, regData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/*
-@func ret_t | rtl8367c_getAsicEeeGiga | Get 100M eee enable/disable.
-@parm rtk_uint32 | port | The port number.
-@parm rtk_uint32* | enabled | 1: enabled, 0: disabled.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input parameter.
-@comm
-    This API get the 100M EEE function.
-*/
-ret_t rtl8367c_getAsicEeeGiga(rtk_uint32 port, rtk_uint32 *enable)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      regData;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if((retVal = rtl8367c_getAsicPHYOCPReg(port, EEE_OCP_PHY_ADDR, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *enable = (regData & (0x0001 << 2)) ? ENABLED : DISABLED;
-    return RT_ERR_OK;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_fc.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_fc.c
deleted file mode 100644
index 28f49b1ba7..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_fc.c
+++ /dev/null
@@ -1,1354 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Flow control related functions
- *
- */
-
-#include <rtl8367c_asicdrv_fc.h>
-/* Function Name:
- *      rtl8367c_setAsicFlowControlSelect
- * Description:
- *      Set system flow control type
- * Input:
- *      select      - System flow control type 1: Ingress flow control 0:Egress flow control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlSelect(rtk_uint32 select)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_FLOWCTRL_CTRL0, RTL8367C_FLOWCTRL_TYPE_OFFSET, select);
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlSelect
- * Description:
- *      Get system flow control type
- * Input:
- *      pSelect         - System flow control type 1: Ingress flow control 0:Egress flow control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlSelect(rtk_uint32 *pSelect)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_FLOWCTRL_CTRL0, RTL8367C_FLOWCTRL_TYPE_OFFSET, pSelect);
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlJumboMode
- * Description:
- *      Set Jumbo threhsold for flow control
- * Input:
- *      enabled         - Jumbo mode flow control 1: Enable 0:Disable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlJumboMode(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_FLOWCTRL_JUMBO_SIZE, RTL8367C_JUMBO_MODE_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlJumboMode
- * Description:
- *      Get Jumbo threhsold for flow control
- * Input:
- *      pEnabled        - Jumbo mode flow control 1: Enable 0:Disable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlJumboMode(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_FLOWCTRL_JUMBO_SIZE, RTL8367C_JUMBO_MODE_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlJumboModeSize
- * Description:
- *      Set Jumbo size for Jumbo mode flow control
- * Input:
- *      size        - Jumbo size 0:3Kbytes 1:4Kbytes 2:6Kbytes 3:9Kbytes
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlJumboModeSize(rtk_uint32 size)
-{
-    if(size >= FC_JUMBO_SIZE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SIZE, RTL8367C_JUMBO_SIZE_MASK, size);
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlJumboModeSize
- * Description:
- *      Get Jumbo size for Jumbo mode flow control
- * Input:
- *      pSize       - Jumbo size 0:3Kbytes 1:4Kbytes 2:6Kbytes 3:9Kbytes
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlJumboModeSize(rtk_uint32* pSize)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SIZE, RTL8367C_JUMBO_SIZE_MASK, pSize);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicFlowControlQueueEgressEnable
- * Description:
- *      Set flow control ability for each queue
- * Input:
- *      port    - Physical port number (0~7)
- *      qid     - Queue id
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- *      RT_ERR_QUEUE_ID - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlQueueEgressEnable(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG(port), RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG_OFFSET(port)+ qid, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlQueueEgressEnable
- * Description:
- *      Get flow control ability for each queue
- * Input:
- *      port    - Physical port number (0~7)
- *      qid     - Queue id
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- *      RT_ERR_QUEUE_ID - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlQueueEgressEnable(rtk_uint32 port, rtk_uint32 qid, rtk_uint32* pEnabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    return  rtl8367c_getAsicRegBit(RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG(port), RTL8367C_FLOWCRTL_EGRESS_QUEUE_ENABLE_REG_OFFSET(port)+ qid, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlDropAll
- * Description:
- *      Set system-based drop parameters
- * Input:
- *      dropall     - Whole system drop threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlDropAll(rtk_uint32 dropall)
-{
-    if(dropall >= RTL8367C_PAGE_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_CTRL0, RTL8367C_DROP_ALL_THRESHOLD_MASK, dropall);
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlDropAll
- * Description:
- *      Get system-based drop parameters
- * Input:
- *      pDropall    - Whole system drop threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlDropAll(rtk_uint32* pDropall)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_CTRL0, RTL8367C_DROP_ALL_THRESHOLD_MASK, pDropall);
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlPauseAll
- * Description:
- *      Set system-based all ports enable flow control parameters
- * Input:
- *      threshold   - Whole system pause all threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlPauseAllThreshold(rtk_uint32 threshold)
-{
-    if(threshold >= RTL8367C_PAGE_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_ALL_ON, RTL8367C_FLOWCTRL_ALL_ON_THRESHOLD_MASK, threshold);
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlPauseAllThreshold
- * Description:
- *      Get system-based all ports enable flow control parameters
- * Input:
- *      pThreshold  - Whole system pause all threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlPauseAllThreshold(rtk_uint32 *pThreshold)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_ALL_ON, RTL8367C_FLOWCTRL_ALL_ON_THRESHOLD_MASK, pThreshold);
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlSystemThreshold
- * Description:
- *      Set system-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlSystemThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_SYS_OFF, RTL8367C_FLOWCTRL_SYS_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_SYS_ON, RTL8367C_FLOWCTRL_SYS_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlSystemThreshold
- * Description:
- *      Get system-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlSystemThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_SYS_OFF, RTL8367C_FLOWCTRL_SYS_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_SYS_ON, RTL8367C_FLOWCTRL_SYS_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlSharedThreshold
- * Description:
- *      Set share-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlSharedThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_SHARE_OFF, RTL8367C_FLOWCTRL_SHARE_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_SHARE_ON, RTL8367C_FLOWCTRL_SHARE_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlSharedThreshold
- * Description:
- *      Get share-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlSharedThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_SHARE_OFF, RTL8367C_FLOWCTRL_SHARE_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_SHARE_ON, RTL8367C_FLOWCTRL_SHARE_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlPortThreshold
- * Description:
- *      Set Port-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlPortThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_OFF, RTL8367C_FLOWCTRL_PORT_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_ON, RTL8367C_FLOWCTRL_PORT_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlPortThreshold
- * Description:
- *      Get Port-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlPortThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_OFF, RTL8367C_FLOWCTRL_PORT_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_ON, RTL8367C_FLOWCTRL_PORT_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlPortPrivateThreshold
- * Description:
- *      Set Port-private-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlPortPrivateThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_PRIVATE_OFF, RTL8367C_FLOWCTRL_PORT_PRIVATE_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_PRIVATE_ON, RTL8367C_FLOWCTRL_PORT_PRIVATE_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlPortPrivateThreshold
- * Description:
- *      Get Port-private-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlPortPrivateThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_PRIVATE_OFF, RTL8367C_FLOWCTRL_PORT_PRIVATE_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_PRIVATE_ON, RTL8367C_FLOWCTRL_PORT_PRIVATE_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlSystemDropThreshold
- * Description:
- *      Set system-based drop parameters
- * Input:
- *      onThreshold     - Drop turn ON threshold
- *      offThreshold    - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlSystemDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SYS_OFF, RTL8367C_FLOWCTRL_FCOFF_SYS_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SYS_ON, RTL8367C_FLOWCTRL_FCOFF_SYS_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlSystemDropThreshold
- * Description:
- *      Get system-based drop parameters
- * Input:
- *      pOnThreshold    - Drop turn ON threshold
- *      pOffThreshold   - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlSystemDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SYS_OFF, RTL8367C_FLOWCTRL_FCOFF_SYS_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SYS_ON, RTL8367C_FLOWCTRL_FCOFF_SYS_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlSharedDropThreshold
- * Description:
- *      Set share-based fdrop parameters
- * Input:
- *      onThreshold     - Drop turn ON threshold
- *      offThreshold    - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlSharedDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SHARE_OFF, RTL8367C_FLOWCTRL_FCOFF_SHARE_OFF_MASK, offThreshold);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SHARE_ON, RTL8367C_FLOWCTRL_FCOFF_SHARE_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlSharedDropThreshold
- * Description:
- *      Get share-based fdrop parameters
- * Input:
- *      pOnThreshold    - Drop turn ON threshold
- *      pOffThreshold   - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlSharedDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SHARE_OFF, RTL8367C_FLOWCTRL_FCOFF_SHARE_OFF_MASK, pOffThreshold);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_SHARE_ON, RTL8367C_FLOWCTRL_FCOFF_SHARE_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlPortDropThreshold
- * Description:
- *      Set Port-based drop parameters
- * Input:
- *      onThreshold     - Drop turn ON threshold
- *      offThreshold    - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlPortDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_OFF, RTL8367C_FLOWCTRL_FCOFF_PORT_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_ON, RTL8367C_FLOWCTRL_FCOFF_PORT_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlPortDropThreshold
- * Description:
- *      Get Port-based drop parameters
- * Input:
- *      pOnThreshold    - Drop turn ON threshold
- *      pOffThreshold   - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlPortDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_OFF, RTL8367C_FLOWCTRL_FCOFF_PORT_OFF_MASK, pOffThreshold);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_ON, RTL8367C_FLOWCTRL_FCOFF_PORT_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlPortPrivateDropThreshold
- * Description:
- *      Set Port-private-based drop parameters
- * Input:
- *      onThreshold     - Drop turn ON threshold
- *      offThreshold    - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlPortPrivateDropThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_PRIVATE_OFF, RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_PRIVATE_ON, RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlPortPrivateDropThreshold
- * Description:
- *      Get Port-private-based drop parameters
- * Input:
- *      pOnThreshold    - Drop turn ON threshold
- *      pOffThreshold   - Drop turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlPortPrivateDropThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_PRIVATE_OFF, RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_OFF_MASK, pOffThreshold);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_FCOFF_PORT_PRIVATE_ON, RTL8367C_FLOWCTRL_FCOFF_PORT_PRIVATE_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlSystemJumboThreshold
- * Description:
- *      Set Jumbo system-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlSystemJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SYS_OFF, RTL8367C_FLOWCTRL_JUMBO_SYS_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SYS_ON, RTL8367C_FLOWCTRL_JUMBO_SYS_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlSystemJumboThreshold
- * Description:
- *      Get Jumbo system-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlSystemJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SYS_OFF, RTL8367C_FLOWCTRL_JUMBO_SYS_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SYS_ON, RTL8367C_FLOWCTRL_JUMBO_SYS_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlSharedJumboThreshold
- * Description:
- *      Set Jumbo share-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlSharedJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SHARE_OFF, RTL8367C_FLOWCTRL_JUMBO_SHARE_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SHARE_ON, RTL8367C_FLOWCTRL_JUMBO_SHARE_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlSharedJumboThreshold
- * Description:
- *      Get Jumbo share-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlSharedJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SHARE_OFF, RTL8367C_FLOWCTRL_JUMBO_SHARE_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_SHARE_ON, RTL8367C_FLOWCTRL_JUMBO_SHARE_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlPortJumboThreshold
- * Description:
- *      Set Jumbo Port-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlPortJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_OFF, RTL8367C_FLOWCTRL_JUMBO_PORT_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_ON, RTL8367C_FLOWCTRL_JUMBO_PORT_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlPortJumboThreshold
- * Description:
- *      Get Jumbo Port-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlPortJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_OFF, RTL8367C_FLOWCTRL_JUMBO_PORT_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_ON, RTL8367C_FLOWCTRL_JUMBO_PORT_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicFlowControlPortPrivateJumboThreshold
- * Description:
- *      Set Jumbo Port-private-based flow control parameters
- * Input:
- *      onThreshold     - Flow control turn ON threshold
- *      offThreshold    - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlPortPrivateJumboThreshold(rtk_uint32 onThreshold, rtk_uint32 offThreshold)
-{
-    ret_t retVal;
-
-    if((onThreshold >= RTL8367C_PAGE_NUMBER) || (offThreshold >= RTL8367C_PAGE_NUMBER))
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF, RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF_MASK, offThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_ON, RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_ON_MASK, onThreshold);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicFlowControlPortPrivateJumboThreshold
- * Description:
- *      Get Jumbo Port-private-based flow control parameters
- * Input:
- *      pOnThreshold    - Flow control turn ON threshold
- *      pOffThreshold   - Flow control turn OFF threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlPortPrivateJumboThreshold(rtk_uint32 *pOnThreshold, rtk_uint32 *pOffThreshold)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF, RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF_MASK, pOffThreshold);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_ON, RTL8367C_FLOWCTRL_JUMBO_PORT_PRIVATE_ON_MASK, pOnThreshold);
-
-    return retVal;
-}
-
-
-
-/* Function Name:
- *      rtl8367c_setAsicEgressFlowControlQueueDropThreshold
- * Description:
- *      Set Queue-based egress flow control turn on or ingress flow control drop on threshold
- * Input:
- *      qid         - The queue id
- *      threshold   - Queue-based flown control/drop turn ON threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- *      RT_ERR_QUEUE_ID     - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicEgressFlowControlQueueDropThreshold(rtk_uint32 qid, rtk_uint32 threshold)
-{
-    if( threshold >= RTL8367C_PAGE_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_FLOWCTRL_QUEUE_DROP_ON_REG(qid), RTL8367C_FLOWCTRL_QUEUE_DROP_ON_MASK, threshold);
-}
-/* Function Name:
- *      rtl8367c_getAsicEgressFlowControlQueueDropThreshold
- * Description:
- *      Get Queue-based egress flow control turn on or ingress flow control drop on threshold
- * Input:
- *      qid         - The queue id
- *      pThreshold  - Queue-based flown control/drop turn ON threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_QUEUE_ID     - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEgressFlowControlQueueDropThreshold(rtk_uint32 qid, rtk_uint32 *pThreshold)
-{
-    if(qid > RTL8367C_QIDMAX)
-      return RT_ERR_QUEUE_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_FLOWCTRL_QUEUE_DROP_ON_REG(qid), RTL8367C_FLOWCTRL_QUEUE_DROP_ON_MASK, pThreshold);
-}
-/* Function Name:
- *      rtl8367c_setAsicEgressFlowControlPortDropThreshold
- * Description:
- *      Set port-based egress flow control turn on or ingress flow control drop on threshold
- * Input:
- *      port        - Physical port number (0~7)
- *      threshold   - Queue-based flown control/drop turn ON threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicEgressFlowControlPortDropThreshold(rtk_uint32 port, rtk_uint32 threshold)
-{
-    if(port > RTL8367C_PORTIDMAX)
-      return RT_ERR_PORT_ID;
-
-    if(threshold >= RTL8367C_PAGE_NUMBER)
-      return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_FLOWCTRL_PORT_DROP_ON_REG(port), RTL8367C_FLOWCTRL_PORT_DROP_ON_MASK, threshold);
-}
-/* Function Name:
- *      rtl8367c_setAsicEgressFlowControlPortDropThreshold
- * Description:
- *      Set port-based egress flow control turn on or ingress flow control drop on threshold
- * Input:
- *      port        - Physical port number (0~7)
- *      pThreshold  - Queue-based flown control/drop turn ON threshold
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEgressFlowControlPortDropThreshold(rtk_uint32 port, rtk_uint32 *pThreshold)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_FLOWCTRL_PORT_DROP_ON_REG(port), RTL8367C_FLOWCTRL_PORT_DROP_ON_MASK, pThreshold);
-}
-/* Function Name:
- *      rtl8367c_setAsicEgressFlowControlPortDropGap
- * Description:
- *      Set port-based egress flow control turn off or ingress flow control drop off gap
- * Input:
- *      gap     - Flow control/drop turn OFF threshold = turn ON threshold - gap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicEgressFlowControlPortDropGap(rtk_uint32 gap)
-{
-    if(gap >= RTL8367C_PAGE_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_GAP, RTL8367C_FLOWCTRL_PORT_GAP_MASK, gap);
-}
-/* Function Name:
- *      rtl8367c_getAsicEgressFlowControlPortDropGap
- * Description:
- *      Get port-based egress flow control turn off or ingress flow control drop off gap
- * Input:
- *      pGap    - Flow control/drop turn OFF threshold = turn ON threshold - gap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEgressFlowControlPortDropGap(rtk_uint32 *pGap)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT_GAP, RTL8367C_FLOWCTRL_PORT_GAP_MASK, pGap);
-}
-/* Function Name:
- *      rtl8367c_setAsicEgressFlowControlQueueDropGap
- * Description:
- *      Set Queue-based egress flow control turn off or ingress flow control drop off gap
- * Input:
- *      gap     - Flow control/drop turn OFF threshold = turn ON threshold - gap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicEgressFlowControlQueueDropGap(rtk_uint32 gap)
-{
-    if(gap >= RTL8367C_PAGE_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_FLOWCTRL_QUEUE_GAP, RTL8367C_FLOWCTRL_QUEUE_GAP_MASK, gap);
-}
-/* Function Name:
- *      rtl8367c_getAsicEgressFlowControlQueueDropGap
- * Description:
- *      Get Queue-based egress flow control turn off or ingress flow control drop off gap
- * Input:
- *      pGap    - Flow control/drop turn OFF threshold = turn ON threshold - gap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEgressFlowControlQueueDropGap(rtk_uint32 *pGap)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_QUEUE_GAP, RTL8367C_FLOWCTRL_QUEUE_GAP_MASK, pGap);
-}
-/* Function Name:
- *      rtl8367c_getAsicEgressQueueEmptyPortMask
- * Description:
- *      Get queue empty port mask
- * Input:
- *      pPortmask   -  Queue empty port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicEgressQueueEmptyPortMask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_PORT_QEMPTY, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicTotalPage
- * Description:
- *      Get system total page usage number
- * Input:
- *      pPageCount  -  page usage number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTotalPage(rtk_uint32 *pPageCount)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_TOTAL_PAGE_COUNTER, RTL8367C_FLOWCTRL_TOTAL_PAGE_COUNTER_MASK, pPageCount);
-}
-/* Function Name:
- *      rtl8367c_getAsicPulbicPage
- * Description:
- *      Get system public page usage number
- * Input:
- *      pPageCount  -  page usage number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPulbicPage(rtk_uint32 *pPageCount)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PUBLIC_PAGE_COUNTER, RTL8367C_FLOWCTRL_PUBLIC_PAGE_COUNTER_MASK, pPageCount);
-}
-/* Function Name:
- *      rtl8367c_getAsicMaxTotalPage
- * Description:
- *      Get system total page max usage number
- * Input:
- *      pPageCount  -  page usage number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMaxTotalPage(rtk_uint32 *pPageCount)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_TOTAL_PAGE_MAX, RTL8367C_FLOWCTRL_TOTAL_PAGE_MAX_MASK, pPageCount);
-}
-/* Function Name:
- *      rtl8367c_getAsicPulbicPage
- * Description:
- *      Get system public page max usage number
- * Input:
- *      pPageCount  -  page usage number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMaxPulbicPage(rtk_uint32 *pPageCount)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PUBLIC_PAGE_MAX, RTL8367C_FLOWCTRL_PUBLIC_PAGE_MAX_MASK, pPageCount);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortPage
- * Description:
- *      Get per-port page usage number
- * Input:
- *      port        -  Physical port number (0~7)
- *      pPageCount  -  page usage number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortPage(rtk_uint32 port, rtk_uint32 *pPageCount)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_FLOWCTRL_PORT_PAGE_COUNTER_REG(port), RTL8367C_FLOWCTRL_PORT_PAGE_COUNTER_MASK, pPageCount);
-    else
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT8_PAGE_COUNTER+port - 8, RTL8367C_FLOWCTRL_PORT_PAGE_COUNTER_MASK, pPageCount);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortPage
- * Description:
- *      Get per-port page max usage number
- * Input:
- *      port        -  Physical port number (0~7)
- *      pPageCount  -  page usage number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortPageMax(rtk_uint32 port, rtk_uint32 *pPageCount)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-    if(port < 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_FLOWCTRL_PORT_PAGE_MAX_REG(port), RTL8367C_FLOWCTRL_PORT_PAGE_MAX_MASK, pPageCount);
-    else
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_FLOWCTRL_PORT0_PAGE_MAX+port-8, RTL8367C_FLOWCTRL_PORT_PAGE_MAX_MASK, pPageCount);
-
-
-}
-
-/* Function Name:
- *      rtl8367c_setAsicFlowControlEgressPortIndep
- * Description:
- *      Set per-port egress flow control independent
- * Input:
- *      port        - Physical port number (0~7)
- *      enabled     - Egress port flow control usage 1:enable 0:disable.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicFlowControlEgressPortIndep(rtk_uint32 port, rtk_uint32 enable)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_PORT0_MISC_CFG + (port *0x20), RTL8367C_PORT0_MISC_CFG_FLOWCTRL_INDEP_OFFSET,enable);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicFlowControlEgressPortIndep
- * Description:
- *      Get per-port egress flow control independent
- * Input:
- *      port        - Physical port number (0~7)
- *      enabled     - Egress port flow control usage 1:enable 0:disable.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFlowControlEgressPortIndep(rtk_uint32 port, rtk_uint32 *pEnable)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_PORT0_MISC_CFG + (port *0x20),RTL8367C_PORT0_MISC_CFG_FLOWCTRL_INDEP_OFFSET,pEnable);
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_green.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_green.c
deleted file mode 100644
index a38623850b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_green.c
+++ /dev/null
@@ -1,445 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Green ethernet related functions
- *
- */
-#include <rtl8367c_asicdrv_green.h>
-
-/* Function Name:
- *      rtl8367c_getAsicGreenPortPage
- * Description:
- *      Get per-Port ingress page usage per second
- * Input:
- *      port    - Physical port number (0~7)
- *      pPage   - page number of ingress packet occuping per second
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      Ingress traffic occuping page number per second for high layer green feature usage
- */
-ret_t rtl8367c_getAsicGreenPortPage(rtk_uint32 port, rtk_uint32* pPage)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint32 pageMeter;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_PAGEMETER_PORT_REG(port), &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-   pageMeter = regData;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_PAGEMETER_PORT_REG(port) + 1, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pageMeter = pageMeter + (regData << 16);
-
-    *pPage = pageMeter;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicGreenTrafficType
- * Description:
- *      Set traffic type for each priority
- * Input:
- *      priority    - internal priority (0~7)
- *      traffictype - high/low traffic type, 1:high priority traffic type, 0:low priority traffic type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicGreenTrafficType(rtk_uint32 priority, rtk_uint32 traffictype)
-{
-
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_HIGHPRI_CFG, priority, (traffictype?1:0));
-}
-/* Function Name:
- *      rtl8367c_getAsicGreenTrafficType
- * Description:
- *      Get traffic type for each priority
- * Input:
- *      priority    - internal priority (0~7)
- *      pTraffictype - high/low traffic type, 1:high priority traffic type, 0:low priority traffic type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicGreenTrafficType(rtk_uint32 priority, rtk_uint32* pTraffictype)
-{
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_HIGHPRI_CFG, priority, pTraffictype);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicGreenHighPriorityTraffic
- * Description:
- *      Set indicator which ASIC had received high priority traffic
- * Input:
- *      port            - Physical port number (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicGreenHighPriorityTraffic(rtk_uint32 port)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_HIGHPRI_INDICATOR, port, 1);
-}
-
-
-/* Function Name:
- *      rtl8367c_getAsicGreenHighPriorityTraffic
- * Description:
- *      Get indicator which ASIC had received high priority traffic or not
- * Input:
- *      port        - Physical port number (0~7)
- *      pIndicator  - Have received high priority traffic indicator. If 1 means ASCI had received high priority in 1second checking priod
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicGreenHighPriorityTraffic(rtk_uint32 port, rtk_uint32* pIndicator)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_HIGHPRI_INDICATOR, port, pIndicator);
-}
-
-/*
-@func rtk_int32 | rtl8367c_setAsicGreenEthernet | Set green ethernet function.
-@parm rtk_uint32 | green | Green feature function usage 1:enable 0:disable.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@comm
-    The API can set Green Ethernet function to reduce power consumption. While green feature is enabled, ASIC will automatic
- detect the cable length and then select different power mode for best performance with minimums power consumption. Link down
- ports will enter power savining mode in 10 seconds after the cable disconnected if power saving function is enabled.
-*/
-ret_t rtl8367c_setAsicGreenEthernet(rtk_uint32 port, rtk_uint32 green)
-{
-    ret_t retVal;
-    rtk_uint32 checkCounter;
-    rtk_uint32 regData;
-    rtk_uint32 phy_status;
-    rtk_uint32 patchData[6][2] = { {0x809A, 0x8911}, {0x80A3, 0x9233}, {0x80AC, 0xA444}, {0x809F, 0x6B20}, {0x80A8, 0x6B22}, {0x80B1, 0x6B23} };
-    rtk_uint32 idx;
-    rtk_uint32 data;
-
-    if (green > 1)
-        return RT_ERR_INPUT;
-
-    /* 0xa420[2:0] */
-    if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xA420, &regData)) != RT_ERR_OK)
-        return retVal;
-    phy_status = (regData & 0x0007);
-
-    if(phy_status == 3)
-    {
-        /* 0xb820[4] = 1 */
-        if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xB820, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        regData |= (0x0001 << 4);
-
-        if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xB820, regData)) != RT_ERR_OK)
-            return retVal;
-
-        /* wait 0xb800[6] = 1 */
-        checkCounter = 100;
-        while(checkCounter)
-        {
-            retVal = rtl8367c_getAsicPHYOCPReg(port, 0xB800, &regData);
-            if( (retVal != RT_ERR_OK) || ((regData & 0x0040) != 0x0040) )
-            {
-                checkCounter --;
-                if(0 == checkCounter)
-                    return RT_ERR_BUSYWAIT_TIMEOUT;
-            }
-            else
-                checkCounter = 0;
-        }
-    }
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &data)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    switch (data)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            if(green)
-            {
-                for(idx = 0; idx < 6; idx++ )
-                {
-                    if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xA436, patchData[idx][0])) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xA438, patchData[idx][1])) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-            break;
-        default:
-            break;;
-    }
-
-
-
-    /* 0xa436 = 0x8011 */
-    if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xA436, 0x8011)) != RT_ERR_OK)
-        return retVal;
-
-    /* wr 0xa438[15] = 0: disable, 1: enable */
-    if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xA438, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(green)
-        regData |= 0x8000;
-    else
-        regData &= 0x7FFF;
-
-    if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xA438, regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(phy_status == 3)
-    {
-        /* 0xb820[4] = 0  */
-        if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xB820, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        regData &= ~(0x0001 << 4);
-
-        if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xB820, regData)) != RT_ERR_OK)
-            return retVal;
-
-        /* wait 0xb800[6] = 0 */
-        checkCounter = 100;
-        while(checkCounter)
-        {
-            retVal = rtl8367c_getAsicPHYOCPReg(port, 0xB800, &regData);
-            if( (retVal != RT_ERR_OK) || ((regData & 0x0040) != 0x0000) )
-            {
-                checkCounter --;
-                if(0 == checkCounter)
-                    return RT_ERR_BUSYWAIT_TIMEOUT;
-            }
-            else
-                checkCounter = 0;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/*
-@func rtk_int32 | rtl8367c_getAsicGreenEthernet | Get green ethernet function.
-@parm rtk_uint32 | *green | Green feature function usage 1:enable 0:disable.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@comm
-    The API can set Green Ethernet function to reduce power consumption. While green feature is enabled, ASIC will automatic
- detect the cable length and then select different power mode for best performance with minimums power consumption. Link down
- ports will enter power savining mode in 10 seconds after the cable disconnected if power saving function is enabled.
-*/
-ret_t rtl8367c_getAsicGreenEthernet(rtk_uint32 port, rtk_uint32* green)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    /* 0xa436 = 0x8011 */
-    if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xA436, 0x8011)) != RT_ERR_OK)
-        return retVal;
-
-    /* wr 0xa438[15] = 0: disable, 1: enable */
-    if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xA438, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(regData & 0x8000)
-        *green = ENABLED;
-    else
-        *green = DISABLED;
-
-    return RT_ERR_OK;
-}
-
-
-/*
-@func ret_t | rtl8367c_setAsicPowerSaving | Set power saving mode
-@parm rtk_uint32 | phy | phy number
-@parm rtk_uint32 | enable | enable power saving mode.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_PORT_ID | Invalid port number.
-@comm
-    The API can set power saving mode per phy.
-*/
-ret_t rtl8367c_setAsicPowerSaving(rtk_uint32 phy, rtk_uint32 enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 phyData;
-    rtk_uint32 regData;
-    rtk_uint32 phy_status;
-    rtk_uint32 checkCounter;
-
-    if (enable > 1)
-        return RT_ERR_INPUT;
-
-    /* 0xa420[2:0] */
-    if((retVal = rtl8367c_getAsicPHYOCPReg(phy, 0xA420, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    phy_status = (regData & 0x0007);
-
-    if(phy_status == 3)
-    {
-        /* 0xb820[4] = 1 */
-        if((retVal = rtl8367c_getAsicPHYOCPReg(phy, 0xB820, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        regData |= (0x0001 << 4);
-
-        if((retVal = rtl8367c_setAsicPHYOCPReg(phy, 0xB820, regData)) != RT_ERR_OK)
-            return retVal;
-
-        /* wait 0xb800[6] = 1 */
-        checkCounter = 100;
-        while(checkCounter)
-        {
-            retVal = rtl8367c_getAsicPHYOCPReg(phy, 0xB800, &regData);
-            if( (retVal != RT_ERR_OK) || ((regData & 0x0040) != 0x0040) )
-            {
-                checkCounter --;
-                if(0 == checkCounter)
-                {
-                     return RT_ERR_BUSYWAIT_TIMEOUT;
-                }
-            }
-            else
-                checkCounter = 0;
-        }
-    }
-
-    if ((retVal = rtl8367c_getAsicPHYReg(phy,PHY_POWERSAVING_REG,&phyData))!=RT_ERR_OK)
-        return retVal;
-
-    phyData = phyData & ~(0x0001 << 2);
-    phyData = phyData | (enable << 2);
-
-    if ((retVal = rtl8367c_setAsicPHYReg(phy,PHY_POWERSAVING_REG,phyData))!=RT_ERR_OK)
-        return retVal;
-
-    if(phy_status == 3)
-    {
-        /* 0xb820[4] = 0  */
-        if((retVal = rtl8367c_getAsicPHYOCPReg(phy, 0xB820, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        regData &= ~(0x0001 << 4);
-
-        if((retVal = rtl8367c_setAsicPHYOCPReg(phy, 0xB820, regData)) != RT_ERR_OK)
-            return retVal;
-
-        /* wait 0xb800[6] = 0 */
-        checkCounter = 100;
-        while(checkCounter)
-        {
-            retVal = rtl8367c_getAsicPHYOCPReg(phy, 0xB800, &regData);
-            if( (retVal != RT_ERR_OK) || ((regData & 0x0040) != 0x0000) )
-            {
-                checkCounter --;
-                if(0 == checkCounter)
-                {
-                    return RT_ERR_BUSYWAIT_TIMEOUT;
-                }
-            }
-            else
-                checkCounter = 0;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/*
-@func ret_t | rtl8367c_getAsicPowerSaving | Get power saving mode
-@parm rtk_uint32 | port | The port number
-@parm rtk_uint32* | enable | enable power saving mode.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_PORT_ID | Invalid port number.
-@comm
-    The API can get power saving mode per phy.
-*/
-ret_t rtl8367c_getAsicPowerSaving(rtk_uint32 phy, rtk_uint32* enable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 phyData;
-
-    if(NULL == enable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPHYReg(phy,PHY_POWERSAVING_REG,&phyData))!=RT_ERR_OK)
-        return retVal;
-
-    if ((phyData & 0x0004) > 0)
-        *enable = 1;
-    else
-        *enable = 0;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_hsb.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_hsb.c
deleted file mode 100644
index 435368d51b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_hsb.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Field selector related functions
- *
- */
-#include <rtl8367c_asicdrv_hsb.h>
-/* Function Name:
- *      rtl8367c_setAsicFieldSelector
- * Description:
- *      Set user defined field selectors in HSB
- * Input:
- *      index       - index of field selector 0-15
- *      format      - Format of field selector
- *      offset      - Retrieving data offset
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      System support 16 user defined field selctors.
- *      Each selector can be enabled or disable. User can defined retrieving 16-bits in many predefiend
- *      standard l2/l3/l4 payload.
- */
-ret_t rtl8367c_setAsicFieldSelector(rtk_uint32 index, rtk_uint32 format, rtk_uint32 offset)
-{
-    rtk_uint32 regData;
-
-    if(index > RTL8367C_FIELDSEL_FORMAT_NUMBER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(format >= FIELDSEL_FORMAT_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    regData = (((format << RTL8367C_FIELD_SELECTOR_FORMAT_OFFSET) & RTL8367C_FIELD_SELECTOR_FORMAT_MASK ) |
-               ((offset << RTL8367C_FIELD_SELECTOR_OFFSET_OFFSET) & RTL8367C_FIELD_SELECTOR_OFFSET_MASK ));
-
-    return rtl8367c_setAsicReg(RTL8367C_FIELD_SELECTOR_REG(index), regData);
-}
-/* Function Name:
- *      rtl8367c_getAsicFieldSelector
- * Description:
- *      Get user defined field selectors in HSB
- * Input:
- *      index       - index of field selector 0-15
- *      pFormat     - Format of field selector
- *      pOffset     - Retrieving data offset
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicFieldSelector(rtk_uint32 index, rtk_uint32* pFormat, rtk_uint32* pOffset)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_FIELD_SELECTOR_REG(index), &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pFormat    = ((regData & RTL8367C_FIELD_SELECTOR_FORMAT_MASK) >> RTL8367C_FIELD_SELECTOR_FORMAT_OFFSET);
-    *pOffset    = ((regData & RTL8367C_FIELD_SELECTOR_OFFSET_MASK) >> RTL8367C_FIELD_SELECTOR_OFFSET_OFFSET);
-
-    return RT_ERR_OK;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_i2c.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_i2c.c
deleted file mode 100644
index 69f20a0188..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_i2c.c
+++ /dev/null
@@ -1,474 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 38651 $
- * $Date: 2016-02-27 14:32:56 +0800 (周三, 17 四月 2016) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : I2C related functions
- *
- */
-
-
-#include <rtl8367c_asicdrv_i2c.h>
-#include <rtk_error.h>
-#include <rtk_types.h>
-
-
-
-/* Function Name:
- *      rtl8367c_setAsicI2C_checkBusIdle
- * Description:
- *      Check i2c bus status idle or not
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- *      RT_ERR_BUSYWAIT_TIMEOUT  - i2c bus is busy
- * Note:
- *      This API can check i2c bus status.
- */
-ret_t rtl8367c_setAsicI2C_checkBusIdle(void)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_M_I2C_BUS_IDLE_OFFSET, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if(regData == 0x0001)
-        return RT_ERR_OK; /*i2c is idle*/
-    else
-        return RT_ERR_BUSYWAIT_TIMEOUT; /*i2c is busy*/
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicI2CStartCmd
- * Description:
- *      Set I2C start command
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can set i2c start command ,start a i2c traffic  .
- */
-ret_t rtl8367c_setAsicI2CStartCmd(void)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    /* Bits [4-1] = 0b0000, Start Command; Bit [0] = 1, Trigger the Command */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFE0;
-    regData |= 0x0001;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /* wait for command finished */
-    do{
-       if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_I2C_CMD_EXEC_OFFSET, &regData)) != RT_ERR_OK)
-            return retVal;
-    }while( regData != 0x0);
-
-    return RT_ERR_OK ;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicI2CStopCmd
- * Description:
- *      Set I2C stop command
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can set i2c stop command ,stop a i2c traffic.
- */
-ret_t rtl8367c_setAsicI2CStopCmd(void)
-{
-
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    /* Bits [4-1] = 0b0001, Stop Command; Bit [0] = 1, Trigger the Command */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFE0;
-    regData |= 0x0003;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, regData)) != RT_ERR_OK)
-        return retVal;
-
-
-    /* wait for command finished */
-    do{
-       if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_I2C_CMD_EXEC_OFFSET, &regData)) != RT_ERR_OK)
-            return retVal;
-    }while( regData != 0x0);
-
-    return RT_ERR_OK ;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicI2CTxOneCharCmd
- * Description:
- *      Set I2C Tx a char command, with a 8-bit data
- * Input:
- *      oneChar - 8-bit data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can set i2c Tx command and with a 8-bit data.
- */
-ret_t rtl8367c_setAsicI2CTxOneCharCmd(rtk_uint8 oneChar)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    /* Bits [4-1] = 0b0010, tx one char; Bit [0] = 1, Trigger the Command */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    regData &= 0xFFE0;
-    regData |= 0x0005;
-    regData &= 0x00FF;
-    regData |= (rtk_uint16) (oneChar << 8);
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, regData)) != RT_ERR_OK)
-        return retVal;
-
-
-   /* wait for command finished */
-    do{
-       if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_I2C_CMD_EXEC_OFFSET, &regData)) != RT_ERR_OK)
-            return retVal;
-    }while( regData != 0x0);
-
-    return RT_ERR_OK ;
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicI2CcheckRxAck
- * Description:
- *      Check if rx an Ack
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can check if rx an ack from i2c slave.
- */
-ret_t rtl8367c_setAsicI2CcheckRxAck(void)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-    rtk_uint32 count = 0;
-
-    do{
-         count++;
-         if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_SLV_ACK_FLAG_OFFSET, &regData)) != RT_ERR_OK)
-            return retVal;
-    }while( (regData != 0x1) && (count < TIMEROUT_FOR_MICROSEMI) );
-
-    if(regData != 0x1)
-        return RT_ERR_FAILED;
-    else
-        return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicI2CRxOneCharCmd
- * Description:
- *      Set I2C Rx command and get 8-bit data
- * Input:
- *      None
- * Output:
- *      pValue - 8bit-data
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can set I2C Rx command and get 8-bit data.
- */
-ret_t rtl8367c_setAsicI2CRxOneCharCmd(rtk_uint8 *pValue)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    /* Bits [4-1] = 0b0011, Rx one char; Bit [0] = 1, Trigger the Command */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFE0;
-    regData |= 0x0007;
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /* wait for command finished */
-     do{
-        if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-             return retVal;
-     }while( (regData & 0x1) != 0x0);
-
-    *pValue = (rtk_uint8)(regData >> 8);
-     return RT_ERR_OK ;
-
-}
-
-/* Function Name:
- *      rtl8367c_setAsicI2CTxAckCmd
- * Description:
- *      Set I2C Tx ACK command
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can set I2C Tx ack command.
- */
-ret_t rtl8367c_setAsicI2CTxAckCmd(void)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    /* Bits [4-1] = 0b0100, tx ACK Command; Bit [0] = 1, Trigger the Command */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFE0;
-    regData |= 0x0009;
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, regData)) != RT_ERR_OK)
-        return retVal;
-
-     /* wait for command finished */
-    do{
-       if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_I2C_CMD_EXEC_OFFSET, &regData)) != RT_ERR_OK)
-            return retVal;
-    }while( regData != 0x0);
-
-    return RT_ERR_OK ;
-
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicI2CTxNoAckCmd
- * Description:
- *      Set I2C master Tx noACK command
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can set I2C master Tx noACK command.
- */
-ret_t rtl8367c_setAsicI2CTxNoAckCmd(void)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    /* Bits [4-1] = 0b0101, tx noACK Command; Bit [0] = 1, Trigger the Command */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFE0;
-    regData |= 0x000b;
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, regData)) != RT_ERR_OK)
-        return retVal;
-
-     /* wait for command finished */
-    do{
-       if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_I2C_CMD_EXEC_OFFSET, &regData)) != RT_ERR_OK)
-            return retVal;
-    }while( regData != 0x0);
-
-    return RT_ERR_OK ;
-
-}
-
-/* Function Name:
- *      rtl8367c_setAsicI2CSoftRSTseqCmd
- * Description:
- *      set I2C master tx soft reset command
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- * Note:
- *      This API can set I2C master tx soft reset command.
- */
-ret_t rtl8367c_setAsicI2CSoftRSTseqCmd(void)
-{
-
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    /*Bits [4-1] = 0b0110, tx soft reset Command;  Bit [0] = 1, Trigger the Command */
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xFFE0;
-    regData |= 0x000d;
-
-    if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_CTL_STA_REG, regData)) != RT_ERR_OK)
-        return retVal;
-
-
-    /* wait for command finished */
-    do{
-       if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_M_I2C_CTL_STA_REG, RTL8367C_I2C_CMD_EXEC_OFFSET, &regData)) != RT_ERR_OK)
-            return retVal;
-    }while( regData != 0x0);
-
-    return RT_ERR_OK ;
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicI2CGpioPinGroup
- * Description:
- *      set I2C function used gpio pins
- * Input:
- *      pinGroup_ID - gpio pins group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- *      RT_ERR_INPUT             _ Invalid input parameter
- * Note:
- *      This API can set I2C function used gpio pins.
- *      There are three group gpio pins
- */
-ret_t rtl8367c_setAsicI2CGpioPinGroup(rtk_uint32 pinGroup_ID)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_SYS_CTL, &regData)) != RT_ERR_OK)
-         return retVal;
-    if( pinGroup_ID==0 )
-    {
-        regData &= 0x0FFF;
-        regData |= 0x5000;
-
-        if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_SYS_CTL, regData)) != RT_ERR_OK)
-             return retVal;
-    }
-
-    else if( pinGroup_ID==1 )
-    {
-        regData &= 0x0FFF;
-        regData |= 0xA000;
-
-        if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_SYS_CTL, regData)) != RT_ERR_OK)
-             return retVal;
-    }
-
-    else if( pinGroup_ID==2 )
-    {
-        regData &= 0x0FFF;
-        regData |= 0xF000;
-
-        if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_M_I2C_SYS_CTL, regData)) != RT_ERR_OK)
-             return retVal;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK ;
-
-}
-
-/* Function Name:
- *      rtl8367c_setAsicI2CGpioPinGroup
- * Description:
- *      set I2C function used gpio pins
- * Input:
- *      pinGroup_ID - gpio pins group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                - Success
- *      RT_ERR_INPUT             _ Invalid input parameter
- * Note:
- *      This API can set I2C function used gpio pins.
- *      There are three group gpio pins
- */
-ret_t rtl8367c_getAsicI2CGpioPinGroup(rtk_uint32 * pPinGroup_ID)
-{
-
-    rtk_uint32 regData;
-    ret_t retVal;
-    if( (retVal = rtl8367c_getAsicReg(RTL8367C_REG_M_I2C_SYS_CTL, &regData)) != RT_ERR_OK)
-        return retVal;
-    regData &= 0xF000 ;
-    regData = (regData >> 12);
-
-    if( regData == 0x5 )
-        *pPinGroup_ID = 0;
-    else if(regData == 0xA)
-        *pPinGroup_ID = 1;
-    else if(regData == 0xF)
-        *pPinGroup_ID = 2;
-    else
-       return RT_ERR_FAILED;
-    return RT_ERR_OK ;
-}
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_igmp.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_igmp.c
deleted file mode 100644
index e0e734d61e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_igmp.c
+++ /dev/null
@@ -1,2109 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : IGMP related functions
- *
- */
-#include <rtl8367c_asicdrv_igmp.h>
-/* Function Name:
- *      rtl8367c_setAsicIgmp
- * Description:
- *      Set IGMP/MLD state
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIgmp(rtk_uint32 enabled)
-{
-    ret_t retVal;
-
-    /* Enable/Disable H/W IGMP/MLD */
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_EN_OFFSET, enabled);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicIgmp
- * Description:
- *      Get IGMP/MLD state
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIgmp(rtk_uint32 *ptr_enabled)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_EN_OFFSET, ptr_enabled);
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicIpMulticastVlanLeaky
- * Description:
- *      Set IP multicast VLAN Leaky function
- * Input:
- *      port        - Physical port number (0~7)
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      When enabling this function,
- *      if the lookup result(forwarding portmap) of IP Multicast packet is over VLAN boundary,
- *      the packet can be forwarded across VLAN
- */
-ret_t rtl8367c_setAsicIpMulticastVlanLeaky(rtk_uint32 port, rtk_uint32 enabled)
-{
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IPMCAST_VLAN_LEAKY, port, enabled);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicIpMulticastVlanLeaky
- * Description:
- *      Get IP multicast VLAN Leaky function
- * Input:
- *      port        - Physical port number (0~7)
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIpMulticastVlanLeaky(rtk_uint32 port, rtk_uint32 *ptr_enabled)
-{
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_IPMCAST_VLAN_LEAKY, port, ptr_enabled);
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPTableFullOP
- * Description:
- *      Set Table Full operation
- * Input:
- *      operation   - The operation should be taken when the IGMP table is full.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter is out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPTableFullOP(rtk_uint32 operation)
-{
-    ret_t  retVal;
-
-    if(operation >= TABLE_FULL_OP_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* Table full Operation */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG1, RTL8367C_TABLE_FULL_OP_MASK, operation);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPTableFullOP
- * Description:
- *      Get Table Full operation
- * Input:
- *      None
- * Output:
- *      poperation  - The operation should be taken when the IGMP table is full.
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPTableFullOP(rtk_uint32 *poperation)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    /* Table full Operation */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG1, RTL8367C_TABLE_FULL_OP_MASK, &value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *poperation = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPCRCErrOP
- * Description:
- *      Set the operation when ASIC receive a Checksum error packet
- * Input:
- *      operation   -The operation when ASIC receive a Checksum error packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter is out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPCRCErrOP(rtk_uint32 operation)
-{
-    ret_t  retVal;
-
-    if(operation >= CRC_ERR_OP_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* CRC Error Operation */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_CKS_ERR_OP_MASK, operation);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPCRCErrOP
- * Description:
- *      Get the operation when ASIC receive a Checksum error packet
- * Input:
- *      None
- * Output:
- *      poperation  - The operation of Checksum error packet
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPCRCErrOP(rtk_uint32 *poperation)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    /* CRC Error Operation */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_CKS_ERR_OP_MASK, &value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *poperation = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPFastLeaveEn
- * Description:
- *      Enable/Disable Fast Leave
- * Input:
- *      enabled - 1:enable Fast Leave; 0:disable Fast Leave
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPFastLeaveEn(rtk_uint32 enabled)
-{
-    ret_t  retVal;
-
-    /* Fast Leave */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_FAST_LEAVE_EN_MASK, (enabled >= 1) ? 1 : 0);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPFastLeaveEn
- * Description:
- *      Get Fast Leave state
- * Input:
- *      None
- * Output:
- *      penabled        - 1:enable Fast Leave; 0:disable Fast Leave
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPFastLeaveEn(rtk_uint32 *penabled)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    /* Fast Leave */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_FAST_LEAVE_EN_MASK, &value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *penabled = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPLeaveTimer
- * Description:
- *      Set the Leave timer of IGMP/MLD
- * Input:
- *      leave_timer     - Leave timer
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter is out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPLeaveTimer(rtk_uint32 leave_timer)
-{
-    ret_t  retVal;
-
-    if(leave_timer > RTL8367C_MAX_LEAVE_TIMER)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* Leave timer */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_LEAVE_TIMER_MASK, leave_timer);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPLeaveTimer
- * Description:
- *      Get the Leave timer of IGMP/MLD
- * Input:
- *      None
- * Output:
- *      pleave_timer    - Leave timer
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPLeaveTimer(rtk_uint32 *pleave_timer)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    /* Leave timer */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_LEAVE_TIMER_MASK, &value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pleave_timer = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPQueryInterval
- * Description:
- *      Set Query Interval of IGMP/MLD
- * Input:
- *      interval    - Query Interval
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter is out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPQueryInterval(rtk_uint32 interval)
-{
-    ret_t  retVal;
-
-    if(interval > RTL8367C_MAX_QUERY_INT)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* Query Interval */
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_IGMP_MLD_CFG2, interval);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPQueryInterval
- * Description:
- *      Get Query Interval of IGMP/MLD
- * Input:
- *      None
- * Output:
- *      pinterval       - Query Interval
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPQueryInterval(rtk_uint32 *pinterval)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    /* Query Interval */
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_IGMP_MLD_CFG2, &value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pinterval = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPRobVar
- * Description:
- *      Set Robustness Variable of IGMP/MLD
- * Input:
- *      rob_var     - Robustness Variable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter is out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPRobVar(rtk_uint32 rob_var)
-{
-    ret_t  retVal;
-
-    if(rob_var > RTL8367C_MAX_ROB_VAR)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* Bourstness variable */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_ROBURSTNESS_VAR_MASK, rob_var);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPRobVar
- * Description:
- *      Get Robustness Variable of IGMP/MLD
- * Input:
- *      none
- * Output:
- *      prob_var     - Robustness Variable
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPRobVar(rtk_uint32 *prob_var)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    /* Bourstness variable */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_ROBURSTNESS_VAR_MASK, &value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *prob_var = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPStaticRouterPort
- * Description:
- *      Set IGMP static router port mask
- * Input:
- *      pmsk    - Static portmask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid port mask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPStaticRouterPort(rtk_uint32 pmsk)
-{
-    if(pmsk > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_STATIC_ROUTER_PORT, RTL8367C_IGMP_STATIC_ROUTER_PORT_MASK, pmsk);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPStaticRouterPort
- * Description:
- *      Get IGMP static router port mask
- * Input:
- *      pmsk    - Static portmask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPStaticRouterPort(rtk_uint32 *pmsk)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_STATIC_ROUTER_PORT, RTL8367C_IGMP_STATIC_ROUTER_PORT_MASK, pmsk);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPAllowDynamicRouterPort
- * Description:
- *      Set IGMP dynamic router port allow mask
- * Input:
- *      pmsk    - Allow dynamic router port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid port mask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPAllowDynamicRouterPort(rtk_uint32 pmsk)
-{
-    return rtl8367c_setAsicReg(RTL8367C_REG_IGMP_MLD_CFG4, pmsk);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPAllowDynamicRouterPort
- * Description:
- *      Get IGMP dynamic router port allow mask
- * Input:
- *      None.
- * Output:
- *      pPmsk   - Allow dynamic router port mask
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid port mask
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPAllowDynamicRouterPort(rtk_uint32 *pPmsk)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_IGMP_MLD_CFG4, pPmsk);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPdynamicRouterPort1
- * Description:
- *      Get 1st dynamic router port and timer
- * Input:
- *      port    - Physical port number (0~7)
- *      timer   - router port timer
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPdynamicRouterPort1(rtk_uint32 *port, rtk_uint32 *timer)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_DYNAMIC_ROUTER_PORT, RTL8367C_D_ROUTER_PORT_1_MASK, port);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_DYNAMIC_ROUTER_PORT, RTL8367C_D_ROUTER_PORT_TMR_1_MASK, timer);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPdynamicRouterPort2
- * Description:
- *      Get 2nd dynamic router port and timer
- * Input:
- *      port    - Physical port number (0~7)
- *      timer   - router port timer
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPdynamicRouterPort2(rtk_uint32 *port, rtk_uint32 *timer)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_DYNAMIC_ROUTER_PORT, RTL8367C_D_ROUTER_PORT_2_MASK, port);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_DYNAMIC_ROUTER_PORT, RTL8367C_D_ROUTER_PORT_TMR_2_MASK, timer);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPSuppression
- * Description:
- *      Set the suppression function
- * Input:
- *      report_supp_enabled     - Report suppression, 1:Enable, 0:disable
- *      leave_supp_enabled      - Leave suppression, 1:Enable, 0:disable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPSuppression(rtk_uint32 report_supp_enabled, rtk_uint32 leave_supp_enabled)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_REPORT_SUPPRESSION_MASK, report_supp_enabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_LEAVE_SUPPRESSION_MASK, leave_supp_enabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPSuppression
- * Description:
- *      Get the suppression function
- * Input:
- *      report_supp_enabled     - Report suppression, 1:Enable, 0:disable
- *      leave_supp_enabled      - Leave suppression, 1:Enable, 0:disable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPSuppression(rtk_uint32 *report_supp_enabled, rtk_uint32 *leave_supp_enabled)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_REPORT_SUPPRESSION_MASK, report_supp_enabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_LEAVE_SUPPRESSION_MASK, leave_supp_enabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPQueryRX
- * Description:
- *      Set port-based Query packet RX allowance
- * Input:
- *      port            - port number
- *      allow_query     - allowance of Query packet RX, 1:Allow, 0:Drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPQueryRX(rtk_uint32 port, rtk_uint32 allow_query)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* Allow Query */
-    if (port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_QUERY_MASK, allow_query);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_QUERY_MASK, allow_query);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPQueryRX
- * Description:
- *      Get port-based Query packet RX allowance
- * Input:
- *      port            - port number
- * Output:
- *      allow_query     - allowance of Query packet RX, 1:Allow, 0:Drop
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPQueryRX(rtk_uint32 port, rtk_uint32 *allow_query)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* Allow Query */
-    if (port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_QUERY_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_QUERY_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    *allow_query = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPReportRX
- * Description:
- *      Set port-based Report packet RX allowance
- * Input:
- *      port            - port number
- *      allow_report    - allowance of Report packet RX, 1:Allow, 0:Drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPReportRX(rtk_uint32 port, rtk_uint32 allow_report)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-    /* Allow Report */
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_REPORT_MASK, allow_report);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_REPORT_MASK, allow_report);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPReportRX
- * Description:
- *      Get port-based Report packet RX allowance
- * Input:
- *      port            - port number
- * Output:
- *      allow_report    - allowance of Report packet RX, 1:Allow, 0:Drop
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPReportRX(rtk_uint32 port, rtk_uint32 *allow_report)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-        /* Allow Report */
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_REPORT_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_REPORT_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    *allow_report = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPLeaveRX
- * Description:
- *      Set port-based Leave packet RX allowance
- * Input:
- *      port            - port number
- *      allow_leave     - allowance of Leave packet RX, 1:Allow, 0:Drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPLeaveRX(rtk_uint32 port, rtk_uint32 allow_leave)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-        /* Allow Leave */
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_LEAVE_MASK, allow_leave);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_LEAVE_MASK, allow_leave);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPLeaveRX
- * Description:
- *      Get port-based Leave packet RX allowance
- * Input:
- *      port            - port number
- * Output:
- *      allow_leave     - allowance of Leave packet RX, 1:Allow, 0:Drop
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPLeaveRX(rtk_uint32 port, rtk_uint32 *allow_leave)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-    /* Allow Leave */
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_LEAVE_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_LEAVE_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *allow_leave = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPMRPRX
- * Description:
- *      Set port-based Multicast Routing Protocol packet RX allowance
- * Input:
- *      port            - port number
- *      allow_mrp       - allowance of Multicast Routing Protocol packet RX, 1:Allow, 0:Drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPMRPRX(rtk_uint32 port, rtk_uint32 allow_mrp)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-    /* Allow Multicast Routing Protocol */
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MRP_MASK, allow_mrp);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MRP_MASK, allow_mrp);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPMRPRX
- * Description:
- *      Get port-based Multicast Routing Protocol packet RX allowance
- * Input:
- *      port            - port number
- * Output:
- *      allow_mrp       - allowance of Multicast Routing Protocol packet RX, 1:Allow, 0:Drop
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPMRPRX(rtk_uint32 port, rtk_uint32 *allow_mrp)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* Allow Multicast Routing Protocol */
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MRP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MRP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    *allow_mrp = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPMcDataRX
- * Description:
- *      Set port-based Multicast data packet RX allowance
- * Input:
- *      port            - port number
- *      allow_mcdata    - allowance of Multicast data packet RX, 1:Allow, 0:Drop
- * Output:
- *      none
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPMcDataRX(rtk_uint32 port, rtk_uint32 allow_mcdata)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* Allow Multicast Data */
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MC_DATA_MASK, allow_mcdata);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MC_DATA_MASK, allow_mcdata);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPMcDataRX
- * Description:
- *      Get port-based Multicast data packet RX allowance
- * Input:
- *      port            - port number
- * Output:
- *      allow_mcdata    - allowance of Multicast data packet RX, 1:Allow, 0:Drop
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPMcDataRX(rtk_uint32 port, rtk_uint32 *allow_mcdata)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* Allow Multicast data */
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MC_DATA_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_ALLOW_MC_DATA_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *allow_mcdata = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPv1Opeartion
- * Description:
- *      Set port-based IGMPv1 Control packet action
- * Input:
- *      port            - port number
- *      igmpv1_op       - IGMPv1 control packet action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPv1Opeartion(rtk_uint32 port, rtk_uint32 igmpv1_op)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(igmpv1_op >= PROTOCOL_OP_END)
-        return RT_ERR_INPUT;
-
-    /* IGMPv1 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_IGMPV1_OP_MASK, igmpv1_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_IGMPV1_OP_MASK, igmpv1_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPv1Opeartion
- * Description:
- *      Get port-based IGMPv1 Control packet action
- * Input:
- *      port            - port number
- * Output:
- *      igmpv1_op       - IGMPv1 control packet action
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPv1Opeartion(rtk_uint32 port, rtk_uint32 *igmpv1_op)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* IGMPv1 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_IGMPV1_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_IGMPV1_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *igmpv1_op = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPv2Opeartion
- * Description:
- *      Set port-based IGMPv2 Control packet action
- * Input:
- *      port            - port number
- *      igmpv2_op       - IGMPv2 control packet action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPv2Opeartion(rtk_uint32 port, rtk_uint32 igmpv2_op)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(igmpv2_op >= PROTOCOL_OP_END)
-        return RT_ERR_INPUT;
-
-    /* IGMPv2 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_IGMPV2_OP_MASK, igmpv2_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_IGMPV2_OP_MASK, igmpv2_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPv2Opeartion
- * Description:
- *      Get port-based IGMPv2 Control packet action
- * Input:
- *      port            - port number
- * Output:
- *      igmpv2_op       - IGMPv2 control packet action
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPv2Opeartion(rtk_uint32 port, rtk_uint32 *igmpv2_op)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* IGMPv2 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_IGMPV2_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_IGMPV2_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *igmpv2_op = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPv3Opeartion
- * Description:
- *      Set port-based IGMPv3 Control packet action
- * Input:
- *      port            - port number
- *      igmpv3_op       - IGMPv3 control packet action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPv3Opeartion(rtk_uint32 port, rtk_uint32 igmpv3_op)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(igmpv3_op >= PROTOCOL_OP_END)
-        return RT_ERR_INPUT;
-
-    /* IGMPv3 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_IGMPV3_OP_MASK, igmpv3_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_IGMPV3_OP_MASK, igmpv3_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPv3Opeartion
- * Description:
- *      Get port-based IGMPv3 Control packet action
- * Input:
- *      port            - port number
- * Output:
- *      igmpv3_op       - IGMPv3 control packet action
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPv3Opeartion(rtk_uint32 port, rtk_uint32 *igmpv3_op)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* IGMPv3 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_IGMPV3_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_IGMPV3_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *igmpv3_op = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMLDv1Opeartion
- * Description:
- *      Set port-based MLDv1 Control packet action
- * Input:
- *      port            - port number
- *      mldv1_op        - MLDv1 control packet action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMLDv1Opeartion(rtk_uint32 port, rtk_uint32 mldv1_op)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(mldv1_op >= PROTOCOL_OP_END)
-        return RT_ERR_INPUT;
-
-    /* MLDv1 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_MLDv1_OP_MASK, mldv1_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_MLDv1_OP_MASK, mldv1_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicMLDv1Opeartion
- * Description:
- *      Get port-based MLDv1 Control packet action
- * Input:
- *      port            - port number
- * Output:
- *      mldv1_op        - MLDv1 control packet action
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMLDv1Opeartion(rtk_uint32 port, rtk_uint32 *mldv1_op)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* MLDv1 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_MLDv1_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_MLDv1_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *mldv1_op = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMLDv2Opeartion
- * Description:
- *      Set port-based MLDv2 Control packet action
- * Input:
- *      port            - port number
- *      mldv2_op        - MLDv2 control packet action
- * Output:
- *      none
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMLDv2Opeartion(rtk_uint32 port, rtk_uint32 mldv2_op)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(mldv2_op >= PROTOCOL_OP_END)
-        return RT_ERR_INPUT;
-
-    /* MLDv2 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_MLDv2_OP_MASK, mldv2_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_MLDv2_OP_MASK, mldv2_op);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicMLDv2Opeartion
- * Description:
- *      Get port-based MLDv2 Control packet action
- * Input:
- *      port            - port number
- * Output:
- *      mldv2_op        - MLDv2 control packet action
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_PORT_ID  - Error PORT ID
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMLDv2Opeartion(rtk_uint32 port, rtk_uint32 *mldv2_op)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    /* MLDv2 operation */
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT0_CONTROL + port, RTL8367C_IGMP_PORT0_CONTROL_MLDv2_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT8_CONTROL + port - 8, RTL8367C_IGMP_PORT0_CONTROL_MLDv2_OP_MASK, &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *mldv2_op = value;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPPortMAXGroup
- * Description:
- *      Set per-port Max group number
- * Input:
- *      port        - Physical port number (0~7)
- *      max_group   - max IGMP group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPPortMAXGroup(rtk_uint32 port, rtk_uint32 max_group)
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(max_group > RTL8367C_IGMP_MAX_GOUP)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT01_MAX_GROUP + (port/2), RTL8367C_PORT0_MAX_GROUP_MASK << (RTL8367C_PORT1_MAX_GROUP_OFFSET * (port%2)), max_group);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_PORT89_MAX_GROUP + (port/2), RTL8367C_PORT0_MAX_GROUP_MASK << (RTL8367C_PORT1_MAX_GROUP_OFFSET * (port%2)), max_group);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicIGMPPortMAXGroup
- * Description:
- *      Get per-port Max group number
- * Input:
- *      port        - Physical port number (0~7)
- *      max_group   - max IGMP group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPPortMAXGroup(rtk_uint32 port, rtk_uint32 *max_group)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT01_MAX_GROUP + (port/2), RTL8367C_PORT0_MAX_GROUP_MASK << (RTL8367C_PORT1_MAX_GROUP_OFFSET * (port%2)), &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT89_MAX_GROUP + (port/2), RTL8367C_PORT0_MAX_GROUP_MASK << (RTL8367C_PORT1_MAX_GROUP_OFFSET * (port%2)), &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *max_group = value;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicIGMPPortCurrentGroup
- * Description:
- *      Get per-port current group number
- * Input:
- *      port            - Physical port number (0~7)
- *      current_group   - current IGMP group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPPortCurrentGroup(rtk_uint32 port, rtk_uint32 *current_group)
-{
-    ret_t   retVal;
-    rtk_uint32  value;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT01_CURRENT_GROUP + (port/2), RTL8367C_PORT0_CURRENT_GROUP_MASK << (RTL8367C_PORT1_CURRENT_GROUP_OFFSET * (port%2)), &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_PORT89_CURRENT_GROUP + ((port - 8)/2), RTL8367C_PORT0_CURRENT_GROUP_MASK << (RTL8367C_PORT1_CURRENT_GROUP_OFFSET * (port%2)), &value);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    *current_group = value;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicIGMPGroup
- * Description:
- *      Get IGMP group
- * Input:
- *      idx     - Group index (0~255)
- *      valid   - valid bit
- *      grp     - IGMP group
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - Group index is out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPGroup(rtk_uint32 idx, rtk_uint32 *valid, rtl8367c_igmpgroup *grp)
-{
-    ret_t   retVal;
-    rtk_uint32  regAddr, regData;
-    rtk_uint32  i;
-    rtk_uint32  groupInfo = 0;
-
-    if(idx > RTL8367C_IGMP_MAX_GOUP)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* Write ACS_ADR register for data bits */
-    regAddr = RTL8367C_TABLE_ACCESS_ADDR_REG;
-    regData = idx;
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write ACS_CMD register */
-    regAddr = RTL8367C_TABLE_ACCESS_CTRL_REG;
-    regData = RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_READ, TB_TARGET_IGMP_GROUP);
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Read Data Bits */
-    regAddr = RTL8367C_TABLE_ACCESS_RDDATA_BASE;
-    for(i = 0 ;i <= 1; i++)
-    {
-        retVal = rtl8367c_getAsicReg(regAddr, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        groupInfo |= ((regData & 0xFFFF) << (i * 16));
-        regAddr ++;
-    }
-
-    grp->p0_timer = groupInfo & 0x00000007;
-    grp->p1_timer = (groupInfo >> 3) & 0x00000007;
-    grp->p2_timer = (groupInfo >> 6) & 0x00000007;
-    grp->p3_timer = (groupInfo >> 9) & 0x00000007;
-    grp->p4_timer = (groupInfo >> 12) & 0x00000007;
-    grp->p5_timer = (groupInfo >> 15) & 0x00000007;
-    grp->p6_timer = (groupInfo >> 18) & 0x00000007;
-    grp->p7_timer = (groupInfo >> 21) & 0x00000007;
-    grp->report_supp_flag = (groupInfo >> 24) & 0x00000001;
-    grp->p8_timer = (groupInfo >> 25) & 0x00000007;
-    grp->p9_timer = (groupInfo >> 28) & 0x00000007;
-    grp->p10_timer = (groupInfo >> 31) & 0x00000001;
-
-    regAddr = RTL8367C_TABLE_ACCESS_RDDATA_BASE + 2;
-    retVal = rtl8367c_getAsicReg(regAddr, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    grp->p10_timer |= (regData & 0x00000003) << 1;
-
-    /* Valid bit */
-    retVal = rtl8367c_getAsicReg(RTL8367C_IGMP_GROUP_USAGE_REG(idx), &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *valid = ((regData & (0x0001 << (idx %16))) != 0) ? 1 : 0;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicIpMulticastPortIsoLeaky
- * Description:
- *      Set IP multicast Port Isolation leaky
- * Input:
- *      port        - Physical port number (0~7)
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIpMulticastPortIsoLeaky(rtk_uint32 port, rtk_uint32 enabled)
-{
-    ret_t   retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_IPMCAST_PORTISO_LEAKY_REG, (0x0001 << port), enabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIpMulticastPortIsoLeaky
- * Description:
- *      Get IP multicast Port Isolation leaky
- * Input:
- *      port        - Physical port number (0~7)
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIpMulticastPortIsoLeaky(rtk_uint32 port, rtk_uint32 *enabled)
-{
-    ret_t   retVal;
-    rtk_uint32  regData;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_IPMCAST_PORTISO_LEAKY_REG, (0x0001 << port), &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *enabled = regData;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPReportLeaveFlood
- * Description:
- *      Set IGMP/MLD Report/Leave flood
- * Input:
- *      flood   - 0: Reserved, 1: flooding to router ports, 2: flooding to all ports, 3: flooding to router port or to all ports if there is no router port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPReportLeaveFlood(rtk_uint32 flood)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG3, RTL8367C_REPORT_LEAVE_FORWARD_MASK, flood);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPReportLeaveFlood
- * Description:
- *      Get IGMP/MLD Report/Leave flood
- * Input:
- *      None
- * Output:
- *      pflood  - 0: Reserved, 1: flooding to router ports, 2: flooding to all ports, 3: flooding to router port or to all ports if there is no router port
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPReportLeaveFlood(rtk_uint32 *pFlood)
-{
-    ret_t   retVal;
-    rtk_uint32  regData;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_IGMP_MLD_CFG3, RTL8367C_REPORT_LEAVE_FORWARD_MASK, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pFlood = regData;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPDropLeaveZero
- * Description:
- *      Set the function of droppping Leave packet with group IP = 0.0.0.0
- * Input:
- *      drop    - 1: Drop, 0:Bypass
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPDropLeaveZero(rtk_uint32 drop)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG1, RTL8367C_DROP_LEAVE_ZERO_OFFSET, drop);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPDropLeaveZero
- * Description:
- *      Get the function of droppping Leave packet with group IP = 0.0.0.0
- * Input:
- *      None
- * Output:
- *      pDrop    - 1: Drop, 0:Bypass
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPDropLeaveZero(rtk_uint32 *pDrop)
-{
-    ret_t   retVal;
-    rtk_uint32  regData;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG1, RTL8367C_DROP_LEAVE_ZERO_OFFSET, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pDrop = regData;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPBypassStormCTRL
- * Description:
- *      Set the function of bypass strom control for IGMP/MLD packet
- * Input:
- *      bypass    - 1: Bypass, 0:not bypass
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPBypassStormCTRL(rtk_uint32 bypass)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_DISCARD_STORM_FILTER_OFFSET, bypass);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPBypassStormCTRL
- * Description:
- *      Set the function of bypass strom control for IGMP/MLD packet
- * Input:
- *      None
- * Output:
- *      pBypass    - 1: Bypass, 0:not bypass
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPBypassStormCTRL(rtk_uint32 *pBypass)
-{
-    ret_t   retVal;
-    rtk_uint32  regData;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_DISCARD_STORM_FILTER_OFFSET, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pBypass = regData;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPIsoLeaky
- * Description:
- *      Set Port Isolation leaky for IGMP/MLD packet
- * Input:
- *      leaky    - 1: Leaky, 0:not leaky
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPIsoLeaky(rtk_uint32 leaky)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_PORTISO_LEAKY_OFFSET, leaky);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPIsoLeaky
- * Description:
- *      Get Port Isolation leaky for IGMP/MLD packet
- * Input:
- *      Noen
- * Output:
- *      pLeaky    - 1: Leaky, 0:not leaky
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPIsoLeaky(rtk_uint32 *pLeaky)
-{
-    ret_t   retVal;
-    rtk_uint32  regData;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_PORTISO_LEAKY_OFFSET, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pLeaky = regData;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPVLANLeaky
- * Description:
- *      Set VLAN leaky for IGMP/MLD packet
- * Input:
- *      leaky    - 1: Leaky, 0:not leaky
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPVLANLeaky(rtk_uint32 leaky)
-{
-    ret_t   retVal;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_VLAN_LEAKY_OFFSET, leaky);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPVLANLeaky
- * Description:
- *      Get VLAN leaky for IGMP/MLD packet
- * Input:
- *      Noen
- * Output:
- *      pLeaky    - 1: Leaky, 0:not leaky
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPVLANLeaky(rtk_uint32 *pLeaky)
-{
-    ret_t   retVal;
-    rtk_uint32  regData;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG0, RTL8367C_IGMP_MLD_VLAN_LEAKY_OFFSET, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pLeaky = regData;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicIGMPBypassGroup
- * Description:
- *      Set IGMP/MLD Bypass group
- * Input:
- *      bypassType  - Bypass type
- *      enabled     - enabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicIGMPBypassGroup(rtk_uint32 bypassType, rtk_uint32 enabled)
-{
-    ret_t   retVal;
-    rtk_uint32 offset;
-
-    switch(bypassType)
-    {
-        case BYPASS_224_0_0_X:
-            offset = RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_0_OFFSET;
-            break;
-        case BYPASS_224_0_1_X:
-            offset = RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_1_OFFSET;
-            break;
-        case BYPASS_239_255_255_X:
-            offset = RTL8367C_IGMP_MLD_IP4_BYPASS_239_255_255_OFFSET;
-            break;
-        case BYPASS_IPV6_00XX:
-            offset = RTL8367C_IGMP_MLD_IP6_BYPASS_OFFSET;
-            break;
-        default:
-            return RT_ERR_INPUT;
-    }
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG3, offset, enabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicIGMPBypassGroup
- * Description:
- *      Get IGMP/MLD Bypass group
- * Input:
- *      bypassType  - Bypass type
- * Output:
- *      pEnabled    - enabled
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicIGMPBypassGroup(rtk_uint32 bypassType, rtk_uint32 *pEnabled)
-{
-    ret_t   retVal;
-    rtk_uint32 offset;
-
-    switch(bypassType)
-    {
-        case BYPASS_224_0_0_X:
-            offset = RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_0_OFFSET;
-            break;
-        case BYPASS_224_0_1_X:
-            offset = RTL8367C_IGMP_MLD_IP4_BYPASS_224_0_1_OFFSET;
-            break;
-        case BYPASS_239_255_255_X:
-            offset = RTL8367C_IGMP_MLD_IP4_BYPASS_239_255_255_OFFSET;
-            break;
-        case BYPASS_IPV6_00XX:
-            offset = RTL8367C_IGMP_MLD_IP6_BYPASS_OFFSET;
-            break;
-        default:
-            return RT_ERR_INPUT;
-    }
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_IGMP_MLD_CFG3, offset, pEnabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_inbwctrl.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_inbwctrl.c
deleted file mode 100644
index abb36bec2d..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_inbwctrl.c
+++ /dev/null
@@ -1,164 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Ingress bandwidth control related functions
- *
- */
-#include <rtl8367c_asicdrv_inbwctrl.h>
-/* Function Name:
- *      rtl8367c_setAsicPortIngressBandwidth
- * Description:
- *      Set per-port total ingress bandwidth
- * Input:
- *      port        - Physical port number (0~7)
- *      bandwidth   - The total ingress bandwidth (unit: 8Kbps), 0x1FFFF:disable
- *      preifg      - Include preamble and IFG, 0:Exclude, 1:Include
- *      enableFC    - Action when input rate exceeds. 0: Drop   1: Flow Control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortIngressBandwidth(rtk_uint32 port, rtk_uint32 bandwidth, rtk_uint32 preifg, rtk_uint32 enableFC)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint32 regAddr;
-
-    /* Invalid input parameter */
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(bandwidth > RTL8367C_QOS_GRANULARTY_MAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    regAddr = RTL8367C_INGRESSBW_PORT_RATE_LSB_REG(port);
-    regData = bandwidth & RTL8367C_QOS_GRANULARTY_LSB_MASK;
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr += 1;
-    regData = (bandwidth & RTL8367C_QOS_GRANULARTY_MSB_MASK) >> RTL8367C_QOS_GRANULARTY_MSB_OFFSET;
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_INGRESSBW_PORT0_RATE_CTRL1_INGRESSBW_RATE16_MASK, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_PORT_MISC_CFG_REG(port);
-    retVal = rtl8367c_setAsicRegBit(regAddr, RTL8367C_PORT0_MISC_CFG_INGRESSBW_IFG_OFFSET, preifg);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_PORT_MISC_CFG_REG(port);
-    retVal = rtl8367c_setAsicRegBit(regAddr, RTL8367C_PORT0_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET, enableFC);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicPortIngressBandwidth
- * Description:
- *      Get per-port total ingress bandwidth
- * Input:
- *      port        - Physical port number (0~7)
- *      pBandwidth  - The total ingress bandwidth (unit: 8Kbps), 0x1FFFF:disable
- *      pPreifg         - Include preamble and IFG, 0:Exclude, 1:Include
- *      pEnableFC   - Action when input rate exceeds. 0: Drop   1: Flow Control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortIngressBandwidth(rtk_uint32 port, rtk_uint32* pBandwidth, rtk_uint32* pPreifg, rtk_uint32* pEnableFC)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint32 regAddr;
-
-    /* Invalid input parameter */
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    regAddr = RTL8367C_INGRESSBW_PORT_RATE_LSB_REG(port);
-    retVal = rtl8367c_getAsicReg(regAddr, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pBandwidth = regData;
-
-    regAddr += 1;
-    retVal = rtl8367c_getAsicRegBits(regAddr, RTL8367C_INGRESSBW_PORT0_RATE_CTRL1_INGRESSBW_RATE16_MASK, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pBandwidth |= (regData << RTL8367C_QOS_GRANULARTY_MSB_OFFSET);
-
-    regAddr = RTL8367C_PORT_MISC_CFG_REG(port);
-    retVal = rtl8367c_getAsicRegBit(regAddr, RTL8367C_PORT0_MISC_CFG_INGRESSBW_IFG_OFFSET, pPreifg);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_PORT_MISC_CFG_REG(port);
-    retVal = rtl8367c_getAsicRegBit(regAddr, RTL8367C_PORT0_MISC_CFG_INGRESSBW_FLOWCTRL_OFFSET, pEnableFC);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicPortIngressBandwidthBypass
- * Description:
- *      Set ingress bandwidth control bypasss 8899, RMA 01-80-C2-00-00-xx and IGMP
- * Input:
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortIngressBandwidthBypass(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_SW_DUMMY0, RTL8367C_INGRESSBW_BYPASS_EN_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortIngressBandwidthBypass
- * Description:
- *      Set ingress bandwidth control bypasss 8899, RMA 01-80-C2-00-00-xx and IGMP
- * Input:
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortIngressBandwidthBypass(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_SW_DUMMY0, RTL8367C_INGRESSBW_BYPASS_EN_OFFSET, pEnabled);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_interrupt.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_interrupt.c
deleted file mode 100644
index fb6cbcdf1f..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_interrupt.c
+++ /dev/null
@@ -1,205 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Interrupt related functions
- *
- */
-#include <rtl8367c_asicdrv_interrupt.h>
-/* Function Name:
- *      rtl8367c_setAsicInterruptPolarity
- * Description:
- *      Set interrupt trigger polarity
- * Input:
- *      polarity    - 0:pull high 1: pull low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicInterruptPolarity(rtk_uint32 polarity)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_INTR_CTRL, RTL8367C_INTR_CTRL_OFFSET, polarity);
-}
-/* Function Name:
- *      rtl8367c_getAsicInterruptPolarity
- * Description:
- *      Get interrupt trigger polarity
- * Input:
- *      pPolarity   - 0:pull high 1: pull low
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicInterruptPolarity(rtk_uint32* pPolarity)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_INTR_CTRL, RTL8367C_INTR_CTRL_OFFSET, pPolarity);
-}
-/* Function Name:
- *      rtl8367c_setAsicInterruptMask
- * Description:
- *      Set interrupt enable mask
- * Input:
- *      imr     - Interrupt mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicInterruptMask(rtk_uint32 imr)
-{
-    return rtl8367c_setAsicReg(RTL8367C_REG_INTR_IMR, imr);
-}
-/* Function Name:
- *      rtl8367c_getAsicInterruptMask
- * Description:
- *      Get interrupt enable mask
- * Input:
- *      pImr    - Interrupt mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicInterruptMask(rtk_uint32* pImr)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_INTR_IMR, pImr);
-}
-/* Function Name:
- *      rtl8367c_setAsicInterruptMask
- * Description:
- *      Clear interrupt enable mask
- * Input:
- *      ims     - Interrupt status mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      This API can be used to clear ASIC interrupt status and register will be cleared by writting 1.
- *      [0]:Link change,
- *      [1]:Share meter exceed,
- *      [2]:Learn number overed,
- *      [3]:Speed Change,
- *      [4]:Tx special congestion
- *      [5]:1 second green feature
- *      [6]:loop detection
- *      [7]:interrupt from 8051
- *      [8]:Cable diagnostic finish
- *      [9]:ACL action interrupt trigger
- *      [11]: Silent Start
- */
-ret_t rtl8367c_setAsicInterruptStatus(rtk_uint32 ims)
-{
-    return rtl8367c_setAsicReg(RTL8367C_REG_INTR_IMS, ims);
-}
-/* Function Name:
- *      rtl8367c_getAsicInterruptStatus
- * Description:
- *      Get interrupt enable mask
- * Input:
- *      pIms    - Interrupt status mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicInterruptStatus(rtk_uint32* pIms)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_INTR_IMS, pIms);
-}
-/* Function Name:
- *      rtl8367c_setAsicInterruptRelatedStatus
- * Description:
- *      Clear interrupt status
- * Input:
- *      type    - per port Learn over, per-port speed change, per-port special congest, share meter exceed status
- *      status  - exceed status, write 1 to clear
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicInterruptRelatedStatus(rtk_uint32 type, rtk_uint32 status)
-{
-    CONST rtk_uint32 indicatorAddress[INTRST_END] = {RTL8367C_REG_LEARN_OVER_INDICATOR,
-                                                    RTL8367C_REG_SPEED_CHANGE_INDICATOR,
-                                                    RTL8367C_REG_SPECIAL_CONGEST_INDICATOR,
-                                                    RTL8367C_REG_PORT_LINKDOWN_INDICATOR,
-                                                    RTL8367C_REG_PORT_LINKUP_INDICATOR,
-                                                    RTL8367C_REG_METER_OVERRATE_INDICATOR0,
-                                                    RTL8367C_REG_METER_OVERRATE_INDICATOR1,
-                                                    RTL8367C_REG_RLDP_LOOPED_INDICATOR,
-                                                    RTL8367C_REG_RLDP_RELEASED_INDICATOR,
-                                                    RTL8367C_REG_SYSTEM_LEARN_OVER_INDICATOR};
-
-    if(type >= INTRST_END )
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicReg(indicatorAddress[type], status);
-}
-/* Function Name:
- *      rtl8367c_getAsicInterruptRelatedStatus
- * Description:
- *      Get interrupt status
- * Input:
- *      type    - per port Learn over, per-port speed change, per-port special congest, share meter exceed status
- *      pStatus     - exceed status, write 1 to clear
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicInterruptRelatedStatus(rtk_uint32 type, rtk_uint32* pStatus)
-{
-    CONST rtk_uint32 indicatorAddress[INTRST_END] = {RTL8367C_REG_LEARN_OVER_INDICATOR,
-                                                    RTL8367C_REG_SPEED_CHANGE_INDICATOR,
-                                                    RTL8367C_REG_SPECIAL_CONGEST_INDICATOR,
-                                                    RTL8367C_REG_PORT_LINKDOWN_INDICATOR,
-                                                    RTL8367C_REG_PORT_LINKUP_INDICATOR,
-                                                    RTL8367C_REG_METER_OVERRATE_INDICATOR0,
-                                                    RTL8367C_REG_METER_OVERRATE_INDICATOR1,
-                                                    RTL8367C_REG_RLDP_LOOPED_INDICATOR,
-                                                    RTL8367C_REG_RLDP_RELEASED_INDICATOR,
-                                                    RTL8367C_REG_SYSTEM_LEARN_OVER_INDICATOR};
-
-    if(type >= INTRST_END )
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_getAsicReg(indicatorAddress[type], pStatus);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_led.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_led.c
deleted file mode 100644
index 1189028161..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_led.c
+++ /dev/null
@@ -1,727 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : LED related functions
- *
- */
-#include <rtl8367c_asicdrv_led.h>
-/* Function Name:
- *      rtl8367c_setAsicLedIndicateInfoConfig
- * Description:
- *      Set Leds indicated information mode
- * Input:
- *      ledno   - LED group number. There are 1 to 1 led mapping to each port in each led group
- *      config  - Support 16 types configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      The API can set LED indicated information configuration for each LED group with 1 to 1 led mapping to each port.
- *      Definition        LED Statuses            Description
- *      0000        LED_Off                LED pin Tri-State.
- *      0001        Dup/Col                Collision, Full duplex Indicator. Blinking every 43ms when collision happens. Low for full duplex, and high for half duplex mode.
- *      0010        Link/Act               Link, Activity Indicator. Low for link established. Link/Act Blinks every 43ms when the corresponding port is transmitting or receiving.
- *      0011        Spd1000                1000Mb/s Speed Indicator. Low for 1000Mb/s.
- *      0100        Spd100                 100Mb/s Speed Indicator. Low for 100Mb/s.
- *      0101        Spd10                  10Mb/s Speed Indicator. Low for 10Mb/s.
- *      0110        Spd1000/Act            1000Mb/s Speed/Activity Indicator. Low for 1000Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
- *      0111        Spd100/Act             100Mb/s Speed/Activity Indicator. Low for 100Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
- *      1000        Spd10/Act              10Mb/s Speed/Activity Indicator. Low for 10Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
- *      1001        Spd100 (10)/Act        10/100Mb/s Speed/Activity Indicator. Low for 10/100Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
- *      1010        Fiber                  Fiber link Indicator. Low for Fiber.
- *      1011        Fault                  Auto-negotiation     Fault Indicator. Low for Fault.
- *      1100        Link/Rx                Link, Activity Indicator. Low for link established. Link/Rx Blinks every 43ms when the corresponding port is transmitting.
- *      1101        Link/Tx                Link, Activity Indicator. Low for link established. Link/Tx Blinks every 43ms when the corresponding port is receiving.
- *      1110        Master                 Link on Master Indicator. Low for link Master established.
- *      1111        LED_Force              Force LED output, LED output value reference
- */
-ret_t rtl8367c_setAsicLedIndicateInfoConfig(rtk_uint32 ledno, rtk_uint32 config)
-{
-    ret_t   retVal;
-    CONST rtk_uint16 bits[RTL8367C_LEDGROUPNO] = {RTL8367C_LED0_CFG_MASK, RTL8367C_LED1_CFG_MASK, RTL8367C_LED2_CFG_MASK};
-
-    if(ledno >= RTL8367C_LEDGROUPNO)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(config >= LEDCONF_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_LED_CONFIG_SEL_OFFSET, 0);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, bits[ledno], config);
-}
-/* Function Name:
- *      rtl8367c_getAsicLedIndicateInfoConfig
- * Description:
- *      Get Leds indicated information mode
- * Input:
- *      ledno   - LED group number. There are 1 to 1 led mapping to each port in each led group
- *      pConfig     - Support 16 types configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLedIndicateInfoConfig(rtk_uint32 ledno, rtk_uint32* pConfig)
-{
-    CONST rtk_uint16 bits[RTL8367C_LEDGROUPNO]= {RTL8367C_LED0_CFG_MASK, RTL8367C_LED1_CFG_MASK, RTL8367C_LED2_CFG_MASK};
-
-    if(ledno >= RTL8367C_LEDGROUPNO)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* Get register value */
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, bits[ledno], pConfig);
-}
-/* Function Name:
- *      rtl8367c_setAsicLedGroupMode
- * Description:
- *      Set Led Group mode
- * Input:
- *      mode    - LED mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLedGroupMode(rtk_uint32 mode)
-{
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if(mode >= RTL8367C_LED_MODE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_LED_CONFIG_SEL_OFFSET, 1);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_DATA_LED_MASK, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicLedGroupMode
- * Description:
- *      Get Led Group mode
- * Input:
- *      pMode   - LED mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLedGroupMode(rtk_uint32* pMode)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_LED_CONFIG_SEL_OFFSET, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    if(regData!=1)
-        return RT_ERR_FAILED;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_DATA_LED_MASK, pMode);
-}
-/* Function Name:
- *      rtl8367c_setAsicForceLeds
- * Description:
- *      Set group LED mode
- * Input:
- *      port    - Physical port number (0~7)
- *      group   - LED group number
- *      mode    - LED mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicForceLed(rtk_uint32 port, rtk_uint32 group, rtk_uint32 mode)
-{
-    rtk_uint16 regAddr;
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(group >= RTL8367C_LEDGROUPNO)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(mode >= LEDFORCEMODE_END)
-        return RT_ERR_OUT_OF_RANGE;
-    /* Set Related Registers */
-    if(port < 8){
-        regAddr = RTL8367C_LED_FORCE_MODE_BASE + (group << 1);
-        if((retVal = rtl8367c_setAsicRegBits(regAddr, 0x3 << (port * 2), mode)) != RT_ERR_OK)
-            return retVal;
-    }else if(port >= 8){
-        regAddr = RTL8367C_REG_CPU_FORCE_LED0_CFG1 + (group << 1);
-        if((retVal = rtl8367c_setAsicRegBits(regAddr, 0x3 << ((port-8) * 2), mode)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicForceLed
- * Description:
- *      Get group LED mode
- * Input:
- *      port    - Physical port number (0~7)
- *      group   - LED group number
- *      pMode   - LED mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicForceLed(rtk_uint32 port, rtk_uint32 group, rtk_uint32* pMode)
-{
-    rtk_uint16 regAddr;
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(group >= RTL8367C_LEDGROUPNO)
-        return RT_ERR_INPUT;
-
-    /* Get Related Registers */
-    if(port < 8){
-        regAddr = RTL8367C_LED_FORCE_MODE_BASE + (group << 1);
-        if((retVal = rtl8367c_getAsicRegBits(regAddr, 0x3 << (port * 2), pMode)) != RT_ERR_OK)
-            return retVal;
-    }else if(port >= 8){
-        regAddr = RTL8367C_REG_CPU_FORCE_LED0_CFG1 + (group << 1);
-        if((retVal = rtl8367c_getAsicRegBits(regAddr, 0x3 << ((port-8) * 2), pMode)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicForceGroupLed
- * Description:
- *      Turn on/off Led of all ports
- * Input:
- *      group   - LED group number
- *      mode    - 0b00:normal mode, 0b01:force blink, 0b10:force off, 0b11:force on
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicForceGroupLed(rtk_uint32 groupmask, rtk_uint32 mode)
-{
-    ret_t retVal;
-    rtk_uint32 i,bitmask;
-    CONST rtk_uint16 bits[3]= {0x0004,0x0010,0x0040};
-
-    /* Invalid input parameter */
-    if(groupmask > RTL8367C_LEDGROUPMASK)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(mode >= LEDFORCEMODE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    bitmask = 0;
-    for(i = 0; i <  RTL8367C_LEDGROUPNO; i++)
-    {
-        if(groupmask & (1 << i))
-        {
-            bitmask = bitmask | bits[i];
-        }
-
-    }
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_LED_FORCE_MODE_MASK, bitmask);
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_FORCE_MODE_MASK, mode);
-
-    if(LEDFORCEMODE_NORMAL == mode)
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_LED_FORCE_MODE_MASK, 0);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicForceGroupLed
- * Description:
- *      Turn on/off Led of all ports
- * Input:
- *      group   - LED group number
- *      pMode   - 0b00:normal mode, 0b01:force blink, 0b10:force off, 0b11:force on
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicForceGroupLed(rtk_uint32* groupmask, rtk_uint32* pMode)
-{
-    ret_t retVal;
-    rtk_uint32 i,regData;
-    CONST rtk_uint16 bits[3] = {0x0004,0x0010,0x0040};
-
-    /* Get Related Registers */
-    if((retVal = rtl8367c_getAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_LED_FORCE_MODE_MASK, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    for(i = 0; i< RTL8367C_LEDGROUPNO; i++)
-    {
-        if((regData & bits[i]) == bits[i])
-        {
-            *groupmask = *groupmask | (1 << i);
-        }
-    }
-
-    return rtl8367c_getAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_FORCE_MODE_MASK, pMode);
-}
-/* Function Name:
- *      rtl8367c_setAsicLedBlinkRate
- * Description:
- *      Set led blinking rate at mode 0 to mode 3
- * Input:
- *      blinkRate   - Support 6 blink rates
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      LED blink rate can be at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms
- */
-ret_t rtl8367c_setAsicLedBlinkRate(rtk_uint32 blinkRate)
-{
-    if(blinkRate >= LEDBLINKRATE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_SEL_LEDRATE_MASK, blinkRate);
-}
-/* Function Name:
- *      rtl8367c_getAsicLedBlinkRate
- * Description:
- *      Get led blinking rate at mode 0 to mode 3
- * Input:
- *      pBlinkRate  - Support 6 blink rates
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLedBlinkRate(rtk_uint32* pBlinkRate)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_SEL_LEDRATE_MASK, pBlinkRate);
-}
-/* Function Name:
- *      rtl8367c_setAsicLedForceBlinkRate
- * Description:
- *      Set LEd blinking rate for force mode led
- * Input:
- *      blinkRate   - Support 6 blink rates
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLedForceBlinkRate(rtk_uint32 blinkRate)
-{
-    if(blinkRate >= LEDFORCERATE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_FORCE_RATE_MASK, blinkRate);
-}
-/* Function Name:
- *      rtl8367c_getAsicLedForceBlinkRate
- * Description:
- *      Get LED blinking rate for force mode led
- * Input:
- *      pBlinkRate  - Support 6 blink rates
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLedForceBlinkRate(rtk_uint32* pBlinkRate)
-{
-     return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_FORCE_RATE_MASK, pBlinkRate);
-}
-
-/*
-@func ret_t | rtl8367c_setAsicLedGroupEnable | Turn on/off Led of all system ports
-@parm rtk_uint32 | group | LED group id.
-@parm rtk_uint32 | portmask | LED port mask.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_PORT_ID | Invalid port number.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can turn on/off leds of dedicated port while indicated information configuration of LED group is set to force mode.
- */
-ret_t rtl8367c_setAsicLedGroupEnable(rtk_uint32 group, rtk_uint32 portmask)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-    rtk_uint32 regDataMask;
-
-    if ( group >= RTL8367C_LEDGROUPNO )
-        return RT_ERR_INPUT;
-
-    regAddr = RTL8367C_REG_PARA_LED_IO_EN1 + group/2;
-    regDataMask = 0xFF << ((group%2)*8);
-    retVal = rtl8367c_setAsicRegBits(regAddr, regDataMask, portmask&0xff);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_REG_PARA_LED_IO_EN3;
-    regDataMask = 0x3 << (group*2);
-    retVal = rtl8367c_setAsicRegBits(regAddr, regDataMask, (portmask>>8)&0x7);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-/*
-@func ret_t | rtl8367c_getAsicLedGroupEnable | Get on/off status of Led of all system ports
-@parm rtk_uint32 | group | LED group id.
-@parm rtk_uint32 | *portmask | LED port mask.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_PORT_ID | Invalid port number.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can turn on/off leds of dedicated port while indicated information configuration of LED group is set to force mode.
- */
-ret_t rtl8367c_getAsicLedGroupEnable(rtk_uint32 group, rtk_uint32 *portmask)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-    rtk_uint32 regDataMask,regData;
-
-    if ( group >= RTL8367C_LEDGROUPNO )
-        return RT_ERR_INPUT;
-
-    regAddr = RTL8367C_REG_PARA_LED_IO_EN1 + group/2;
-    regDataMask = 0xFF << ((group%2)*8);
-    retVal = rtl8367c_getAsicRegBits(regAddr, regDataMask, portmask);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-
-    regAddr = RTL8367C_REG_PARA_LED_IO_EN3;
-    regDataMask = 0x3 << (group*2);
-    retVal = rtl8367c_getAsicRegBits(regAddr, regDataMask, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *portmask = (regData << 8) | *portmask;
-
-    return RT_ERR_OK;
-}
-
-/*
-@func ret_t | rtl8367c_setAsicLedOperationMode | Set LED operation mode
-@parm rtk_uint32 | mode | LED mode. 1:scan mode 1, 2:parallel mode, 3:mdx mode (serial mode)
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can turn on/off led serial mode and set signal to active high/low.
- */
-ret_t rtl8367c_setAsicLedOperationMode(rtk_uint32 mode)
-{
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if( mode >= LEDOP_END)
-        return RT_ERR_INPUT;
-
-    switch(mode)
-    {
-        case LEDOP_PARALLEL:
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_SELECT_OFFSET, 0))!=  RT_ERR_OK)
-                return retVal;
-            /*Disable serial CLK mode*/
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_CLK_EN_OFFSET, 0))!=  RT_ERR_OK)
-                return retVal;
-            /*Disable serial DATA mode*/
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_DATA_EN_OFFSET, 0))!=  RT_ERR_OK)
-                return retVal;
-            break;
-        case LEDOP_SERIAL:
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_SELECT_OFFSET, 1))!=  RT_ERR_OK)
-                return retVal;
-            /*Enable serial CLK mode*/
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_CLK_EN_OFFSET, 1))!=  RT_ERR_OK)
-                return retVal;
-            /*Enable serial DATA mode*/
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_DATA_EN_OFFSET, 1))!=  RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            return RT_ERR_INPUT;
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-
-/*
-@func ret_t | rtl8367c_getAsicLedOperationMode | Get LED OP mode setup
-@parm rtk_uint32*| mode | LED mode. 1:scan mode 1, 2:parallel mode, 3:mdx mode (serial mode)
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can get LED serial mode setup and get signal active high/low.
- */
-ret_t rtl8367c_getAsicLedOperationMode(rtk_uint32 *mode)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_SELECT_OFFSET, &regData))!=  RT_ERR_OK)
-        return retVal;
-
-    if (regData == 1)
-        *mode = LEDOP_SERIAL;
-    else if (regData == 0)
-        *mode = LEDOP_PARALLEL;
-    else
-        return RT_ERR_FAILED;
-
-    return RT_ERR_OK;
-}
-
-/*
-@func ret_t | rtl8367c_setAsicLedSerialModeConfig | Set LED serial mode
-@parm rtk_uint32 | active | Active High or Low.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can turn on/off led serial mode and set signal to active high/low.
- */
-ret_t rtl8367c_setAsicLedSerialModeConfig(rtk_uint32 active, rtk_uint32 serimode)
-{
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if( active >= LEDSERACT_MAX)
-        return RT_ERR_INPUT;
-    if( serimode >= LEDSER_MAX)
-        return RT_ERR_INPUT;
-
-    /* Set Active High or Low */
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_SERI_LED_ACT_LOW_OFFSET, active)) !=  RT_ERR_OK)
-        return retVal;
-
-    /*set to 8G mode (not 16G mode)*/
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_MODE, RTL8367C_DLINK_TIME_OFFSET, serimode))!=  RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-
-/*
-@func ret_t | rtl8367c_getAsicLedSerialModeConfig | Get LED serial mode setup
-@parm rtk_uint32*| active | Active High or Low.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can get LED serial mode setup and get signal active high/low.
- */
-ret_t rtl8367c_getAsicLedSerialModeConfig(rtk_uint32 *active, rtk_uint32 *serimode)
-{
-    ret_t retVal;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_SERI_LED_ACT_LOW_OFFSET, active))!=  RT_ERR_OK)
-        return retVal;
-
-    /*get to 8G mode (not 16G mode)*/
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_MODE, RTL8367C_DLINK_TIME_OFFSET, serimode))!=  RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/*
-@func ret_t | rtl8367c_setAsicLedOutputEnable | Set LED output enable
-@parm rtk_uint32 | enabled | enable or disalbe.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can turn on/off LED output Enable
- */
-ret_t rtl8367c_setAsicLedOutputEnable(rtk_uint32 enabled)
-{
-    ret_t retVal;
-    rtk_uint32 regdata;
-
-    if (enabled == 1)
-        regdata = 0;
-    else
-        regdata = 1;
-
-    /* Enable/Disable H/W IGMP/MLD */
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_IO_DISABLE_OFFSET, regdata);
-
-    return retVal;
-}
-
-
-/*
-@func ret_t | rtl8367c_getAsicLedOutputEnable | Get LED serial mode setup
-@parm rtk_uint32*| active | Active High or Low.
-@rvalue RT_ERR_OK | Success.
-@rvalue RT_ERR_SMI | SMI access error.
-@rvalue RT_ERR_INPUT | Invalid input value.
-@comm
-    The API can get LED serial mode setup and get signal active high/low.
- */
-ret_t rtl8367c_getAsicLedOutputEnable(rtk_uint32 *ptr_enabled)
-{
-    ret_t retVal;
-    rtk_uint32 regdata;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_IO_DISABLE_OFFSET, &regdata);
-    if (retVal != RT_ERR_OK)
-        return retVal;
-
-    if (regdata == 1)
-        *ptr_enabled = 0;
-    else
-        *ptr_enabled = 1;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLedSerialOutput
- * Description:
- *      Set serial LED output group and portmask.
- * Input:
- *      output      - Serial LED output group
- *      pmask       - Serial LED output portmask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLedSerialOutput(rtk_uint32 output, rtk_uint32 pmask)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_GROUP_NUM_MASK, output);
-    if (retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_PORT_EN_MASK, pmask);
-    if (retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicLedSerialOutput
- * Description:
- *      Get serial LED output group and portmask.
- * Input:
- *      None
- * Output:
- *      pOutput      - Serial LED output group
- *      pPmask       - Serial LED output portmask
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLedSerialOutput(rtk_uint32 *pOutput, rtk_uint32 *pPmask)
-{
-    ret_t retVal;
-
-    if(pOutput == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(pPmask == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_GROUP_NUM_MASK, pOutput);
-    if (retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_PORT_EN_MASK, pPmask);
-    if (retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_lut.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_lut.c
deleted file mode 100644
index 343a6f159c..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_lut.c
+++ /dev/null
@@ -1,1549 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : LUT related functions
- *
- */
-
-#include <rtl8367c_asicdrv_lut.h>
-
-#include <string.h>
-
-static void _rtl8367c_fdbStUser2Smi( rtl8367c_luttb *pLutSt, rtk_uint16 *pFdbSmi)
-{
-    /* L3 lookup */
-    if(pLutSt->l3lookup)
-    {
-        if(pLutSt->l3vidlookup)
-        {
-            pFdbSmi[0] = (pLutSt->sip & 0x0000FFFF);
-            pFdbSmi[1] = (pLutSt->sip & 0xFFFF0000) >> 16;
-
-            pFdbSmi[2] = (pLutSt->dip & 0x0000FFFF);
-            pFdbSmi[3] = (pLutSt->dip & 0x0FFF0000) >> 16;
-
-            pFdbSmi[3] |= (pLutSt->l3lookup & 0x0001) << 12;
-            pFdbSmi[3] |= (pLutSt->l3vidlookup & 0x0001) << 13;
-            pFdbSmi[3] |= ((pLutSt->mbr & 0x0300) >> 8) << 14;
-
-            pFdbSmi[4] |= (pLutSt->mbr & 0x00FF);
-            pFdbSmi[4] |= (pLutSt->l3_vid & 0x00FF) << 8;
-
-            pFdbSmi[5] |= ((pLutSt->l3_vid & 0x0F00) >> 8);
-            pFdbSmi[5] |= (pLutSt->nosalearn & 0x0001) << 5;
-            pFdbSmi[5] |= ((pLutSt->mbr & 0x0400) >> 10) << 7;
-        }
-        else
-        {
-            pFdbSmi[0] = (pLutSt->sip & 0x0000FFFF);
-            pFdbSmi[1] = (pLutSt->sip & 0xFFFF0000) >> 16;
-
-            pFdbSmi[2] = (pLutSt->dip & 0x0000FFFF);
-            pFdbSmi[3] = (pLutSt->dip & 0x0FFF0000) >> 16;
-
-            pFdbSmi[3] |= (pLutSt->l3lookup & 0x0001) << 12;
-            pFdbSmi[3] |= (pLutSt->l3vidlookup & 0x0001) << 13;
-            pFdbSmi[3] |= ((pLutSt->mbr & 0x0300) >> 8) << 14;
-
-            pFdbSmi[4] |= (pLutSt->mbr & 0x00FF);
-            pFdbSmi[4] |= (pLutSt->igmpidx & 0x00FF) << 8;
-
-            pFdbSmi[5] |= (pLutSt->igmp_asic & 0x0001);
-            pFdbSmi[5] |= (pLutSt->lut_pri & 0x0007) << 1;
-            pFdbSmi[5] |= (pLutSt->fwd_en & 0x0001) << 4;
-            pFdbSmi[5] |= (pLutSt->nosalearn & 0x0001) << 5;
-            pFdbSmi[5] |= ((pLutSt->mbr & 0x0400) >> 10) << 7;
-        }
-    }
-    else if(pLutSt->mac.octet[0] & 0x01) /*Multicast L2 Lookup*/
-    {
-        pFdbSmi[0] |= pLutSt->mac.octet[5];
-        pFdbSmi[0] |= pLutSt->mac.octet[4] << 8;
-
-        pFdbSmi[1] |= pLutSt->mac.octet[3];
-        pFdbSmi[1] |= pLutSt->mac.octet[2] << 8;
-
-        pFdbSmi[2] |= pLutSt->mac.octet[1];
-        pFdbSmi[2] |= pLutSt->mac.octet[0] << 8;
-
-        pFdbSmi[3] |= pLutSt->cvid_fid;
-        pFdbSmi[3] |= (pLutSt->l3lookup & 0x0001) << 12;
-        pFdbSmi[3] |= (pLutSt->ivl_svl & 0x0001) << 13;
-        pFdbSmi[3] |= ((pLutSt->mbr & 0x0300) >> 8) << 14;
-
-        pFdbSmi[4] |= (pLutSt->mbr & 0x00FF);
-        pFdbSmi[4] |= (pLutSt->igmpidx & 0x00FF) << 8;
-
-        pFdbSmi[5] |= pLutSt->igmp_asic;
-        pFdbSmi[5] |= (pLutSt->lut_pri & 0x0007) << 1;
-        pFdbSmi[5] |= (pLutSt->fwd_en & 0x0001) << 4;
-        pFdbSmi[5] |= (pLutSt->nosalearn & 0x0001) << 5;
-        pFdbSmi[5] |= ((pLutSt->mbr & 0x0400) >> 10) << 7;
-    }
-    else /*Asic auto-learning*/
-    {
-        pFdbSmi[0] |= pLutSt->mac.octet[5];
-        pFdbSmi[0] |= pLutSt->mac.octet[4] << 8;
-
-        pFdbSmi[1] |= pLutSt->mac.octet[3];
-        pFdbSmi[1] |= pLutSt->mac.octet[2] << 8;
-
-        pFdbSmi[2] |= pLutSt->mac.octet[1];
-        pFdbSmi[2] |= pLutSt->mac.octet[0] << 8;
-
-        pFdbSmi[3] |= pLutSt->cvid_fid;
-        pFdbSmi[3] |= (pLutSt->l3lookup & 0x0001) << 12;
-        pFdbSmi[3] |= (pLutSt->ivl_svl & 0x0001) << 13;
-        pFdbSmi[3] |= ((pLutSt->spa & 0x0008) >> 3) << 15;
-
-        pFdbSmi[4] |= pLutSt->efid;
-        pFdbSmi[4] |= (pLutSt->fid & 0x000F) << 3;
-        pFdbSmi[4] |= (pLutSt->sa_en & 0x0001) << 7;
-        pFdbSmi[4] |= (pLutSt->spa & 0x0007) << 8;
-        pFdbSmi[4] |= (pLutSt->age & 0x0007) << 11;
-        pFdbSmi[4] |= (pLutSt->auth & 0x0001) << 14;
-        pFdbSmi[4] |= (pLutSt->sa_block & 0x0001) << 15;
-
-        pFdbSmi[5] |= pLutSt->da_block;
-        pFdbSmi[5] |= (pLutSt->lut_pri & 0x0007) << 1;
-        pFdbSmi[5] |= (pLutSt->fwd_en & 0x0001) << 4;
-        pFdbSmi[5] |= (pLutSt->nosalearn & 0x0001) << 5;
-    }
-}
-
-
-static void _rtl8367c_fdbStSmi2User( rtl8367c_luttb *pLutSt, rtk_uint16 *pFdbSmi)
-{
-    /*L3 lookup*/
-    if(pFdbSmi[3] & 0x1000)
-    {
-        if(pFdbSmi[3] & 0x2000)
-        {
-            pLutSt->sip             = pFdbSmi[0] | (pFdbSmi[1] << 16);
-            pLutSt->dip             = pFdbSmi[2] | ((pFdbSmi[3] & 0x0FFF) << 16);
-
-            pLutSt->mbr             = (pFdbSmi[4] & 0x00FF) | (((pFdbSmi[3] & 0xC000) >> 14) << 8) | (((pFdbSmi[5] & 0x0080) >> 7) << 10);
-            pLutSt->l3_vid          = ((pFdbSmi[4] & 0xFF00) >> 8) | (pFdbSmi[5] & 0x000F);
-
-            pLutSt->l3lookup        = (pFdbSmi[3] & 0x1000) >> 12;
-            pLutSt->l3vidlookup     = (pFdbSmi[3] & 0x2000) >> 13;
-            pLutSt->nosalearn       = (pFdbSmi[5] & 0x0020) >> 5;
-        }
-        else
-        {
-            pLutSt->sip             = pFdbSmi[0] | (pFdbSmi[1] << 16);
-            pLutSt->dip             = pFdbSmi[2] | ((pFdbSmi[3] & 0x0FFF) << 16);
-
-            pLutSt->lut_pri         = (pFdbSmi[5] & 0x000E) >> 1;
-            pLutSt->fwd_en          = (pFdbSmi[5] & 0x0010) >> 4;
-
-            pLutSt->mbr             = (pFdbSmi[4] & 0x00FF) | (((pFdbSmi[3] & 0xC000) >> 14) << 8) | (((pFdbSmi[5] & 0x0080) >> 7) << 10);
-            pLutSt->igmpidx         = (pFdbSmi[4] & 0xFF00) >> 8;
-
-            pLutSt->igmp_asic       = (pFdbSmi[5] & 0x0001);
-            pLutSt->l3lookup        = (pFdbSmi[3] & 0x1000) >> 12;
-            pLutSt->nosalearn       = (pFdbSmi[5] & 0x0020) >> 5;
-        }
-    }
-    else if(pFdbSmi[2] & 0x0100) /*Multicast L2 Lookup*/
-    {
-        pLutSt->mac.octet[0]    = (pFdbSmi[2] & 0xFF00) >> 8;
-        pLutSt->mac.octet[1]    = (pFdbSmi[2] & 0x00FF);
-        pLutSt->mac.octet[2]    = (pFdbSmi[1] & 0xFF00) >> 8;
-        pLutSt->mac.octet[3]    = (pFdbSmi[1] & 0x00FF);
-        pLutSt->mac.octet[4]    = (pFdbSmi[0] & 0xFF00) >> 8;
-        pLutSt->mac.octet[5]    = (pFdbSmi[0] & 0x00FF);
-
-        pLutSt->cvid_fid        = pFdbSmi[3] & 0x0FFF;
-        pLutSt->lut_pri         = (pFdbSmi[5] & 0x000E) >> 1;
-        pLutSt->fwd_en          = (pFdbSmi[5] & 0x0010) >> 4;
-
-        pLutSt->mbr             = (pFdbSmi[4] & 0x00FF) | (((pFdbSmi[3] & 0xC000) >> 14) << 8) | (((pFdbSmi[5] & 0x0080) >> 7) << 10);
-        pLutSt->igmpidx         = (pFdbSmi[4] & 0xFF00) >> 8;
-
-        pLutSt->igmp_asic       = (pFdbSmi[5] & 0x0001);
-        pLutSt->l3lookup        = (pFdbSmi[3] & 0x1000) >> 12;
-        pLutSt->ivl_svl         = (pFdbSmi[3] & 0x2000) >> 13;
-        pLutSt->nosalearn       = (pFdbSmi[5] & 0x0020) >> 5;
-    }
-    else /*Asic auto-learning*/
-    {
-        pLutSt->mac.octet[0]    = (pFdbSmi[2] & 0xFF00) >> 8;
-        pLutSt->mac.octet[1]    = (pFdbSmi[2] & 0x00FF);
-        pLutSt->mac.octet[2]    = (pFdbSmi[1] & 0xFF00) >> 8;
-        pLutSt->mac.octet[3]    = (pFdbSmi[1] & 0x00FF);
-        pLutSt->mac.octet[4]    = (pFdbSmi[0] & 0xFF00) >> 8;
-        pLutSt->mac.octet[5]    = (pFdbSmi[0] & 0x00FF);
-
-        pLutSt->cvid_fid        = pFdbSmi[3] & 0x0FFF;
-        pLutSt->lut_pri         = (pFdbSmi[5] & 0x000E) >> 1;
-        pLutSt->fwd_en          = (pFdbSmi[5] & 0x0010) >> 4;
-
-        pLutSt->sa_en           = (pFdbSmi[4] & 0x0080) >> 7;
-        pLutSt->auth            = (pFdbSmi[4] & 0x4000) >> 14;
-        pLutSt->spa             = ((pFdbSmi[4] & 0x0700) >> 8) | (((pFdbSmi[3] & 0x8000) >> 15) << 3);
-        pLutSt->age             = (pFdbSmi[4] & 0x3800) >> 11;
-        pLutSt->fid             = (pFdbSmi[4] & 0x0078) >> 3;
-        pLutSt->efid            = (pFdbSmi[4] & 0x0007);
-        pLutSt->sa_block        = (pFdbSmi[4] & 0x8000) >> 15;
-
-        pLutSt->da_block        = (pFdbSmi[5] & 0x0001);
-        pLutSt->l3lookup        = (pFdbSmi[3] & 0x1000) >> 12;
-        pLutSt->ivl_svl         = (pFdbSmi[3] & 0x2000) >> 13;
-        pLutSt->nosalearn       = (pFdbSmi[3] & 0x0020) >> 5;
-    }
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutIpMulticastLookup
- * Description:
- *      Set Lut IP multicast lookup function
- * Input:
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutIpMulticastLookup(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_LUT_IPMC_HASH_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutIpMulticastLookup
- * Description:
- *      Get Lut IP multicast lookup function
- * Input:
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutIpMulticastLookup(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_LUT_IPMC_HASH_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutIpMulticastLookup
- * Description:
- *      Set Lut IP multicast + VID lookup function
- * Input:
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutIpMulticastVidLookup(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_LUT_CFG2, RTL8367C_LUT_IPMC_VID_HASH_OFFSET, enabled);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicLutIpMulticastVidLookup
- * Description:
- *      Get Lut IP multicast lookup function
- * Input:
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutIpMulticastVidLookup(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_LUT_CFG2, RTL8367C_LUT_IPMC_VID_HASH_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutIpLookupMethod
- * Description:
- *      Set Lut IP lookup hash with DIP or {DIP,SIP} pair
- * Input:
- *      type - 1: When DIP can be found in IPMC_GROUP_TABLE, use DIP+SIP Hash, otherwise, use DIP+(SIP=0.0.0.0) Hash.
- *             0: When DIP can be found in IPMC_GROUP_TABLE, use DIP+(SIP=0.0.0.0) Hash, otherwise use DIP+SIP Hash.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutIpLookupMethod(rtk_uint32 type)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_LUT_IPMC_LOOKUP_OP_OFFSET, type);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutIpLookupMethod
- * Description:
- *      Get Lut IP lookup hash with DIP or {DIP,SIP} pair
- * Input:
- *      pType - 1: When DIP can be found in IPMC_GROUP_TABLE, use DIP+SIP Hash, otherwise, use DIP+(SIP=0.0.0.0) Hash.
- *              0: When DIP can be found in IPMC_GROUP_TABLE, use DIP+(SIP=0.0.0.0) Hash, otherwise use DIP+SIP Hash.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutIpLookupMethod(rtk_uint32* pType)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_LUT_IPMC_LOOKUP_OP_OFFSET, pType);
-}
-/* Function Name:
- *      rtl8367c_setAsicLutAgeTimerSpeed
- * Description:
- *      Set LUT agging out speed
- * Input:
- *      timer - Agging out timer 0:Has been aged out
- *      speed - Agging out speed 0-fastest 3-slowest
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutAgeTimerSpeed(rtk_uint32 timer, rtk_uint32 speed)
-{
-    if(timer>RTL8367C_LUT_AGETIMERMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(speed >RTL8367C_LUT_AGESPEEDMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_LUT_CFG, RTL8367C_AGE_TIMER_MASK | RTL8367C_AGE_SPEED_MASK, (timer << RTL8367C_AGE_TIMER_OFFSET) | (speed << RTL8367C_AGE_SPEED_OFFSET));
-}
-/* Function Name:
- *      rtl8367c_getAsicLutAgeTimerSpeed
- * Description:
- *      Get LUT agging out speed
- * Input:
- *      pTimer - Agging out timer 0:Has been aged out
- *      pSpeed - Agging out speed 0-fastest 3-slowest
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutAgeTimerSpeed(rtk_uint32* pTimer, rtk_uint32* pSpeed)
-{
-    rtk_uint32 regData;
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_LUT_CFG, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pTimer =  (regData & RTL8367C_AGE_TIMER_MASK) >> RTL8367C_AGE_TIMER_OFFSET;
-
-    *pSpeed =  (regData & RTL8367C_AGE_SPEED_MASK) >> RTL8367C_AGE_SPEED_OFFSET;
-
-    return RT_ERR_OK;
-
-}
-/* Function Name:
- *      rtl8367c_setAsicLutCamTbUsage
- * Description:
- *      Configure Lut CAM table usage
- * Input:
- *      enabled - L2 CAM table usage 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutCamTbUsage(rtk_uint32 enabled)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_BCAM_DISABLE_OFFSET, enabled ? 0 : 1);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicLutCamTbUsage
- * Description:
- *      Get Lut CAM table usage
- * Input:
- *      pEnabled - L2 CAM table usage 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutCamTbUsage(rtk_uint32* pEnabled)
-{
-    ret_t       retVal;
-    rtk_uint32  regData;
-
-    if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_BCAM_DISABLE_OFFSET, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pEnabled = regData ? 0 : 1;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicLutLearnLimitNo
- * Description:
- *      Set per-Port auto learning limit number
- * Input:
- *      port    - Physical port number (0~7)
- *      number  - ASIC auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number
- *      RT_ERR_LIMITED_L2ENTRY_NUM  - Invalid auto learning limit number
- * Note:
- *      None
- */
-   /*ÐÞ¸Ä: RTL8367C_PORTIDMAX, RTL8367C_LUT_LEARNLIMITMAX, RTL8367C_LUT_PORT_LEARN_LIMITNO_REG*/
-ret_t rtl8367c_setAsicLutLearnLimitNo(rtk_uint32 port, rtk_uint32 number)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(number > RTL8367C_LUT_LEARNLIMITMAX)
-        return RT_ERR_LIMITED_L2ENTRY_NUM;
-
-    if(port < 8)
-     return rtl8367c_setAsicReg(RTL8367C_LUT_PORT_LEARN_LIMITNO_REG(port), number);
-    else
-        return rtl8367c_setAsicReg(RTL8367C_REG_LUT_PORT8_LEARN_LIMITNO+port-8, number);
-
-}
-/* Function Name:
- *      rtl8367c_getAsicLutLearnLimitNo
- * Description:
- *      Get per-Port auto learning limit number
- * Input:
- *      port    - Physical port number (0~7)
- *      pNumber     - ASIC auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-  /*ÐÞ¸Ä: RTL8367C_PORTIDMAX, RTL8367C_LUT_PORT_LEARN_LIMITNO_REG*/
-ret_t rtl8367c_getAsicLutLearnLimitNo(rtk_uint32 port, rtk_uint32* pNumber)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-     return rtl8367c_getAsicReg(RTL8367C_LUT_PORT_LEARN_LIMITNO_REG(port), pNumber);
-    else
-        return rtl8367c_getAsicReg(RTL8367C_REG_LUT_PORT8_LEARN_LIMITNO+port-8, pNumber);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicSystemLutLearnLimitNo
- * Description:
- *      Set system auto learning limit number
- * Input:
- *      number  - ASIC auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number
- *      RT_ERR_LIMITED_L2ENTRY_NUM  - Invalid auto learning limit number
- * Note:
- *      None
- */
-  /*ÐÞ¸Ä: RTL8367C_LUT_LEARNLIMITMAX*/
-ret_t rtl8367c_setAsicSystemLutLearnLimitNo(rtk_uint32 number)
-{
-    if(number > RTL8367C_LUT_LEARNLIMITMAX)
-        return RT_ERR_LIMITED_L2ENTRY_NUM;
-
-    return rtl8367c_setAsicReg(RTL8367C_REG_LUT_SYS_LEARN_LIMITNO, number);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicSystemLutLearnLimitNo
- * Description:
- *      Get system auto learning limit number
- * Input:
- *      port    - Physical port number (0~7)
- *      pNumber     - ASIC auto learning entries limit number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSystemLutLearnLimitNo(rtk_uint32 *pNumber)
-{
-    if(NULL == pNumber)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicReg(RTL8367C_REG_LUT_SYS_LEARN_LIMITNO, pNumber);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutLearnOverAct
- * Description:
- *      Set auto learn over limit number action
- * Input:
- *      action  - Learn over action 0:normal, 1:drop 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NOT_ALLOWED  - Invalid learn over action
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutLearnOverAct(rtk_uint32 action)
-{
-    if(action >= LRNOVERACT_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_PORT_SECURITY_CTRL, RTL8367C_LUT_LEARN_OVER_ACT_MASK, action);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutLearnOverAct
- * Description:
- *      Get auto learn over limit number action
- * Input:
- *      pAction     - Learn over action 0:normal, 1:drop 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutLearnOverAct(rtk_uint32* pAction)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_SECURITY_CTRL, RTL8367C_LUT_LEARN_OVER_ACT_MASK, pAction);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicSystemLutLearnOverAct
- * Description:
- *      Set system auto learn over limit number action
- * Input:
- *      action  - Learn over action 0:normal, 1:drop, 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NOT_ALLOWED  - Invalid learn over action
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSystemLutLearnOverAct(rtk_uint32 action)
-{
-    if(action >= LRNOVERACT_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_LUT_LRN_SYS_LMT_CTRL, RTL8367C_LUT_SYSTEM_LEARN_OVER_ACT_MASK, action);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicSystemLutLearnOverAct
- * Description:
- *      Get system auto learn over limit number action
- * Input:
- *      pAction     - Learn over action 0:normal, 1:drop 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSystemLutLearnOverAct(rtk_uint32 *pAction)
-{
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_LUT_LRN_SYS_LMT_CTRL, RTL8367C_LUT_SYSTEM_LEARN_OVER_ACT_MASK, pAction);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicSystemLutLearnPortMask
- * Description:
- *      Set system auto learn limit port mask
- * Input:
- *      portmask    - port mask of system learning limit
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Error port mask
- * Note:
- *      None
- */
-  /*ÐÞ¸Ä: RTL8367C_LUT_SYSTEM_LEARN_PMASK_MASK*/
-ret_t rtl8367c_setAsicSystemLutLearnPortMask(rtk_uint32 portmask)
-{
-    ret_t retVal;
-
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_LUT_LRN_SYS_LMT_CTRL, RTL8367C_LUT_SYSTEM_LEARN_PMASK_MASK, portmask & 0xff);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_LUT_LRN_SYS_LMT_CTRL, RTL8367C_LUT_SYSTEM_LEARN_PMASK1_MASK, (portmask>>8) & 0x7);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtl8367c_getAsicSystemLutLearnPortMask
- * Description:
- *      Get system auto learn limit port mask
- * Input:
- *      None
- * Output:
- *      pPortmask   - port mask of system learning limit
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - NULL pointer
- * Note:
- *      None
- */
- /*ÐÞ¸Ä: RTL8367C_LUT_SYSTEM_LEARN_PMASK_MASK*/
-ret_t rtl8367c_getAsicSystemLutLearnPortMask(rtk_uint32 *pPortmask)
-{
-    rtk_uint32 tmpmask;
-    ret_t retVal;
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_LUT_LRN_SYS_LMT_CTRL, RTL8367C_LUT_SYSTEM_LEARN_PMASK_MASK, &tmpmask);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask = tmpmask & 0xff;
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_LUT_LRN_SYS_LMT_CTRL, RTL8367C_LUT_SYSTEM_LEARN_PMASK1_MASK, &tmpmask);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask |= (tmpmask & 0x7) << 8;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicL2LookupTb
- * Description:
- *      Set filtering database entry
- * Input:
- *      pL2Table    - L2 table entry writing to 8K+64 filtering database
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicL2LookupTb(rtl8367c_luttb *pL2Table)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smil2Table[RTL8367C_LUT_TABLE_SIZE];
-    rtk_uint32 tblCmd;
-    rtk_uint32 busyCounter;
-
-    memset(smil2Table, 0x00, sizeof(rtk_uint16) * RTL8367C_LUT_TABLE_SIZE);
-    _rtl8367c_fdbStUser2Smi(pL2Table, smil2Table);
-
-    if(pL2Table->wait_time == 0)
-        busyCounter = RTL8367C_LUT_BUSY_CHECK_NO;
-    else
-        busyCounter = pL2Table->wait_time;
-
-    while(busyCounter)
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_OFFSET,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        pL2Table->lookup_busy = regData;
-        if(!regData)
-            break;
-
-        busyCounter --;
-        if(busyCounter == 0)
-            return RT_ERR_BUSYWAIT_TIMEOUT;
-    }
-
-    accessPtr = smil2Table;
-    regData = *accessPtr;
-    for(i = 0; i < RTL8367C_LUT_ENTRY_SIZE; i++)
-    {
-        retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_WRDATA_BASE + i, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        accessPtr ++;
-        regData = *accessPtr;
-
-    }
-
-    tblCmd = (RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_WRITE,TB_TARGET_L2)) & (RTL8367C_TABLE_TYPE_MASK  | RTL8367C_COMMAND_TYPE_MASK);
-    /* Write Command */
-    retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_CTRL_REG, tblCmd);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    if(pL2Table->wait_time == 0)
-        busyCounter = RTL8367C_LUT_BUSY_CHECK_NO;
-    else
-        busyCounter = pL2Table->wait_time;
-
-    while(busyCounter)
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_OFFSET,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        pL2Table->lookup_busy = regData;
-        if(!regData)
-            break;
-
-        busyCounter --;
-        if(busyCounter == 0)
-            return RT_ERR_BUSYWAIT_TIMEOUT;
-    }
-
-    /*Read access status*/
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_HIT_STATUS_OFFSET, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pL2Table->lookup_hit = regData;
-    if(!pL2Table->lookup_hit)
-        return RT_ERR_FAILED;
-
-    /*Read access address*/
-    /*
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_TYPE_MASK | RTL8367C_TABLE_LUT_ADDR_ADDRESS_MASK,&regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pL2Table->address = regData;*/
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_TABLE_ACCESS_STATUS_REG, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pL2Table->address = (regData & 0x7ff) | ((regData & 0x4000) >> 3) | ((regData & 0x800) << 1);
-    pL2Table->lookup_busy = 0;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicL2LookupTb
- * Description:
- *      Get filtering database entry
- * Input:
- *      pL2Table    - L2 table entry writing to 2K+64 filtering database
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameter
- *      RT_ERR_BUSYWAIT_TIMEOUT - LUT is busy at retrieving
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicL2LookupTb(rtk_uint32 method, rtl8367c_luttb *pL2Table)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16* accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smil2Table[RTL8367C_LUT_TABLE_SIZE];
-    rtk_uint32 busyCounter;
-    rtk_uint32 tblCmd;
-
-    if(pL2Table->wait_time == 0)
-        busyCounter = RTL8367C_LUT_BUSY_CHECK_NO;
-    else
-        busyCounter = pL2Table->wait_time;
-
-    while(busyCounter)
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_OFFSET,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        pL2Table->lookup_busy = regData;
-        if(!pL2Table->lookup_busy)
-            break;
-
-        busyCounter --;
-        if(busyCounter == 0)
-            return RT_ERR_BUSYWAIT_TIMEOUT;
-    }
-
-
-    tblCmd = (method << RTL8367C_ACCESS_METHOD_OFFSET) & RTL8367C_ACCESS_METHOD_MASK;
-
-    switch(method)
-    {
-        case LUTREADMETHOD_ADDRESS:
-        case LUTREADMETHOD_NEXT_ADDRESS:
-        case LUTREADMETHOD_NEXT_L2UC:
-        case LUTREADMETHOD_NEXT_L2MC:
-        case LUTREADMETHOD_NEXT_L3MC:
-        case LUTREADMETHOD_NEXT_L2L3MC:
-            retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_ADDR_REG, pL2Table->address);
-            if(retVal != RT_ERR_OK)
-                return retVal;
-            break;
-        case LUTREADMETHOD_MAC:
-            memset(smil2Table, 0x00, sizeof(rtk_uint16) * RTL8367C_LUT_TABLE_SIZE);
-            _rtl8367c_fdbStUser2Smi(pL2Table, smil2Table);
-
-            accessPtr = smil2Table;
-            regData = *accessPtr;
-            for(i=0; i<RTL8367C_LUT_ENTRY_SIZE; i++)
-            {
-                retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_WRDATA_BASE + i, regData);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-
-                accessPtr ++;
-                regData = *accessPtr;
-
-            }
-            break;
-        case LUTREADMETHOD_NEXT_L2UCSPA:
-            retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_ADDR_REG, pL2Table->address);
-            if(retVal != RT_ERR_OK)
-                return retVal;
-
-            tblCmd = tblCmd | ((pL2Table->spa << RTL8367C_TABLE_ACCESS_CTRL_SPA_OFFSET) & RTL8367C_TABLE_ACCESS_CTRL_SPA_MASK);
-
-            break;
-        default:
-            return RT_ERR_INPUT;
-    }
-
-    tblCmd = tblCmd | ((RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_READ,TB_TARGET_L2)) & (RTL8367C_TABLE_TYPE_MASK  | RTL8367C_COMMAND_TYPE_MASK));
-    /* Read Command */
-    retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_CTRL_REG, tblCmd);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    if(pL2Table->wait_time == 0)
-        busyCounter = RTL8367C_LUT_BUSY_CHECK_NO;
-    else
-        busyCounter = pL2Table->wait_time;
-
-    while(busyCounter)
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_OFFSET,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        pL2Table->lookup_busy = regData;
-        if(!pL2Table->lookup_busy)
-            break;
-
-        busyCounter --;
-        if(busyCounter == 0)
-            return RT_ERR_BUSYWAIT_TIMEOUT;
-    }
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_HIT_STATUS_OFFSET,&regData);
-    if(retVal != RT_ERR_OK)
-            return retVal;
-    pL2Table->lookup_hit = regData;
-    if(!pL2Table->lookup_hit)
-        return RT_ERR_L2_ENTRY_NOTFOUND;
-
-    /*Read access address*/
-    //retVal = rtl8367c_getAsicRegBits(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_TYPE_MASK | RTL8367C_TABLE_LUT_ADDR_ADDRESS_MASK,&regData);
-    retVal = rtl8367c_getAsicReg(RTL8367C_TABLE_ACCESS_STATUS_REG, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pL2Table->address = (regData & 0x7ff) | ((regData & 0x4000) >> 3) | ((regData & 0x800) << 1);
-
-    /*read L2 entry */
-    memset(smil2Table, 0x00, sizeof(rtk_uint16) * RTL8367C_LUT_TABLE_SIZE);
-
-    accessPtr = smil2Table;
-
-    for(i = 0; i < RTL8367C_LUT_ENTRY_SIZE; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_TABLE_ACCESS_RDDATA_BASE + i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *accessPtr = regData;
-
-        accessPtr ++;
-    }
-
-    _rtl8367c_fdbStSmi2User(pL2Table, smil2Table);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicLutLearnNo
- * Description:
- *      Get per-Port auto learning number
- * Input:
- *      port    - Physical port number (0~7)
- *      pNumber     - ASIC auto learning entries number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
- /*ÐÞ¸ÄRTL8367C_PORTIDMAX, RTL8367C_REG_L2_LRN_CNT_REG, port10 reg is not contnious, wait for updating of base.h*/
-ret_t rtl8367c_getAsicLutLearnNo(rtk_uint32 port, rtk_uint32* pNumber)
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 10)
-    {
-     retVal = rtl8367c_getAsicReg(RTL8367C_REG_L2_LRN_CNT_REG(port), pNumber);
-        if (retVal != RT_ERR_OK)
-         return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_REG_L2_LRN_CNT_CTRL10, pNumber);
-        if (retVal != RT_ERR_OK)
-         return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutFlushAll
- * Description:
- *      Flush all entries in LUT. Includes static & dynamic entries
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutFlushAll(void)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_L2_FLUSH_CTRL3, RTL8367C_L2_FLUSH_CTRL3_OFFSET, 1);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicLutFlushAllStatus
- * Description:
- *      Get Flush all status, 1:Busy, 0 normal
- * Input:
- *      None
- * Output:
- *      pBusyStatus - Busy state
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutFlushAllStatus(rtk_uint32 *pBusyStatus)
-{
-    if(NULL == pBusyStatus)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_L2_FLUSH_CTRL3, RTL8367C_L2_FLUSH_CTRL3_OFFSET, pBusyStatus);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutForceFlush
- * Description:
- *      Set per port force flush setting
- * Input:
- *      portmask    - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *      None
- */
- /*port8~port10µÄÉèÖÃÔÚÁíÍâÒ»¸öregister, wait for updating of base.h, reg.h*/
-ret_t rtl8367c_setAsicLutForceFlush(rtk_uint32 portmask)
-{
-    ret_t retVal;
-
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_FORCE_FLUSH_REG, RTL8367C_FORCE_FLUSH_PORTMASK_MASK, portmask & 0xff);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_FORCE_FLUSH1, RTL8367C_PORTMASK1_MASK, (portmask >> 8) & 0x7);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicLutForceFlushStatus
- * Description:
- *      Get per port force flush status
- * Input:
- *      pPortmask   - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
- /*port8~port10µÄÉèÖÃÔÚÁíÍâÒ»¸öregister, wait for updating of base.h, reg.h*/
-ret_t rtl8367c_getAsicLutForceFlushStatus(rtk_uint32 *pPortmask)
-{
-    rtk_uint32 tmpMask;
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_FORCE_FLUSH_REG, RTL8367C_BUSY_STATUS_MASK,&tmpMask);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask = tmpMask & 0xff;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_FORCE_FLUSH1, RTL8367C_BUSY_STATUS1_MASK,&tmpMask);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask |= (tmpMask & 7) << 8;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicLutFlushMode
- * Description:
- *      Set user force L2 pLutSt table flush mode
- * Input:
- *      mode    - 0:Port based 1: Port + VLAN based 2:Port + FID/MSTI based
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NOT_ALLOWED  - Actions not allowed by the function
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutFlushMode(rtk_uint32 mode)
-{
-    if( mode >= FLUSHMDOE_END )
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_L2_FLUSH_CTRL2, RTL8367C_LUT_FLUSH_MODE_MASK, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutFlushMode
- * Description:
- *      Get user force L2 pLutSt table flush mode
- * Input:
- *      pMode   - 0:Port based 1: Port + VLAN based 2:Port + FID/MSTI based
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutFlushMode(rtk_uint32* pMode)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_L2_FLUSH_CTRL2, RTL8367C_LUT_FLUSH_MODE_MASK, pMode);
-}
-/* Function Name:
- *      rtl8367c_setAsicLutFlushType
- * Description:
- *      Get L2 LUT flush type
- * Input:
- *      type    - 0: dynamice unicast; 1: both dynamic and static unicast entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutFlushType(rtk_uint32 type)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_L2_FLUSH_CTRL2, RTL8367C_LUT_FLUSH_TYPE_OFFSET,type);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutFlushType
- * Description:
- *      Set L2 LUT flush type
- * Input:
- *      pType   - 0: dynamice unicast; 1: both dynamic and static unicast entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutFlushType(rtk_uint32* pType)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_L2_FLUSH_CTRL2, RTL8367C_LUT_FLUSH_TYPE_OFFSET,pType);
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicLutFlushVid
- * Description:
- *      Set VID of Port + VID pLutSt flush mode
- * Input:
- *      vid     - Vid (0~4095)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_VLAN_VID - Invalid VID parameter (0~4095)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutFlushVid(rtk_uint32 vid)
-{
-    if( vid > RTL8367C_VIDMAX )
-        return RT_ERR_VLAN_VID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_L2_FLUSH_CTRL1, RTL8367C_LUT_FLUSH_VID_MASK, vid);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutFlushVid
- * Description:
- *      Get VID of Port + VID pLutSt flush mode
- * Input:
- *      pVid    - Vid (0~4095)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutFlushVid(rtk_uint32* pVid)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_L2_FLUSH_CTRL1, RTL8367C_LUT_FLUSH_VID_MASK, pVid);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortFlusdFid
- * Description:
- *      Set FID of Port + FID pLutSt flush mode
- * Input:
- *      fid     - FID/MSTI for force flush
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_L2_FID   - Invalid FID (0~15)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutFlushFid(rtk_uint32 fid)
-{
-    if( fid > RTL8367C_FIDMAX )
-        return RT_ERR_L2_FID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_L2_FLUSH_CTRL1, RTL8367C_LUT_FLUSH_FID_MASK, fid);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutFlushFid
- * Description:
- *      Get FID of Port + FID pLutSt flush mode
- * Input:
- *      pFid    - FID/MSTI for force flush
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutFlushFid(rtk_uint32* pFid)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_L2_FLUSH_CTRL1, RTL8367C_LUT_FLUSH_FID_MASK, pFid);
-}
-/* Function Name:
- *      rtl8367c_setAsicLutDisableAging
- * Description:
- *      Set L2 LUT aging per port setting
- * Input:
- *      port    - Physical port number (0~7)
- *      disabled    - 0: enable aging; 1: disabling aging
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
- /*ÐÞ¸ÄRTL8367C_PORTIDMAX*/
-ret_t rtl8367c_setAsicLutDisableAging(rtk_uint32 port, rtk_uint32 disabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_LUT_AGEOUT_CTRL_REG, port, disabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicLutDisableAging
- * Description:
- *      Get L2 LUT aging per port setting
- * Input:
- *      port    - Physical port number (0~7)
- *      pDisabled - 0: enable aging; 1: disabling aging
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
- /*ÐÞ¸ÄRTL8367C_PORTIDMAX*/
-ret_t rtl8367c_getAsicLutDisableAging(rtk_uint32 port, rtk_uint32 *pDisabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_LUT_AGEOUT_CTRL_REG, port, pDisabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutIPMCGroup
- * Description:
- *      Set IPMC Group Table
- * Input:
- *      index       - the entry index in table (0 ~ 63)
- *      group_addr  - the multicast group address (224.0.0.0 ~ 239.255.255.255)
- *      vid         - VLAN ID
- *      pmask       - portmask
- *      valid       - valid bit
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutIPMCGroup(rtk_uint32 index, ipaddr_t group_addr, rtk_uint32 vid, rtk_uint32 pmask, rtk_uint32 valid)
-{
-    rtk_uint32  regAddr, regData, bitoffset;
-    ipaddr_t    ipData;
-    ret_t       retVal;
-
-    if(index > RTL8367C_LUT_IPMCGRP_TABLE_MAX)
-        return RT_ERR_INPUT;
-
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    ipData = group_addr;
-
-    if( (ipData & 0xF0000000) != 0xE0000000)    /* not in 224.0.0.0 ~ 239.255.255.255 */
-        return RT_ERR_INPUT;
-
-    /* Group Address */
-    regAddr = RTL8367C_REG_IPMC_GROUP_ENTRY0_H + (index * 2);
-    regData = ((ipData & 0x0FFFFFFF) >> 16);
-
-    if( (retVal = rtl8367c_setAsicReg(regAddr, regData)) != RT_ERR_OK)
-        return retVal;
-
-    regAddr++;
-    regData = (ipData & 0x0000FFFF);
-
-    if( (retVal = rtl8367c_setAsicReg(regAddr, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /* VID */
-    regAddr = RTL8367C_REG_IPMC_GROUP_VID_00 + index;
-    regData = vid;
-
-    if( (retVal = rtl8367c_setAsicReg(regAddr, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /* portmask */
-    regAddr = RTL8367C_REG_IPMC_GROUP_PMSK_00 + index;
-    regData = pmask;
-
-    if( (retVal = rtl8367c_setAsicReg(regAddr, regData)) != RT_ERR_OK)
-        return retVal;
-
-    /* valid */
-    regAddr = RTL8367C_REG_IPMC_GROUP_VALID_15_0 + (index / 16);
-    bitoffset = index % 16;
-    if( (retVal = rtl8367c_setAsicRegBit(regAddr, bitoffset, valid)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicLutIPMCGroup
- * Description:
- *      Set IPMC Group Table
- * Input:
- *      index       - the entry index in table (0 ~ 63)
- * Output:
- *      pGroup_addr - the multicast group address (224.0.0.0 ~ 239.255.255.255)
- *      pVid        - VLAN ID
- *      pPmask      - portmask
- *      pValid      - Valid bit
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutIPMCGroup(rtk_uint32 index, ipaddr_t *pGroup_addr, rtk_uint32 *pVid, rtk_uint32 *pPmask, rtk_uint32 *pValid)
-{
-    rtk_uint32      regAddr, regData, bitoffset;
-    ipaddr_t    ipData;
-    ret_t       retVal;
-
-    if(index > RTL8367C_LUT_IPMCGRP_TABLE_MAX)
-        return RT_ERR_INPUT;
-
-    if (NULL == pGroup_addr)
-        return RT_ERR_NULL_POINTER;
-
-    if (NULL == pVid)
-        return RT_ERR_NULL_POINTER;
-
-    if (NULL == pPmask)
-        return RT_ERR_NULL_POINTER;
-
-    /* Group address */
-    regAddr = RTL8367C_REG_IPMC_GROUP_ENTRY0_H + (index * 2);
-    if( (retVal = rtl8367c_getAsicReg(regAddr, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pGroup_addr = (((regData & 0x00000FFF) << 16) | 0xE0000000);
-
-    regAddr++;
-    if( (retVal = rtl8367c_getAsicReg(regAddr, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    ipData = (*pGroup_addr | (regData & 0x0000FFFF));
-    *pGroup_addr = ipData;
-
-    /* VID */
-    regAddr = RTL8367C_REG_IPMC_GROUP_VID_00 + index;
-    if( (retVal = rtl8367c_getAsicReg(regAddr, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pVid = regData;
-
-    /* portmask */
-    regAddr = RTL8367C_REG_IPMC_GROUP_PMSK_00 + index;
-    if( (retVal = rtl8367c_getAsicReg(regAddr, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pPmask = regData;
-
-    /* valid */
-    regAddr = RTL8367C_REG_IPMC_GROUP_VALID_15_0 + (index / 16);
-    bitoffset = index % 16;
-    if( (retVal = rtl8367c_getAsicRegBit(regAddr, bitoffset, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pValid = regData;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutLinkDownForceAging
- * Description:
- *       Set LUT link down aging setting.
- * Input:
- *      enable      - link down aging setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_ENABLE    - Invalid parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutLinkDownForceAging(rtk_uint32 enable)
-{
-    if(enable > 1)
-        return RT_ERR_ENABLE;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_LINKDOWN_AGEOUT_OFFSET, enable ? 0 : 1);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicLutLinkDownForceAging
- * Description:
- *       Get LUT link down aging setting.
- * Input:
- *      pEnable         - link down aging setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_ENABLE    - Invalid parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutLinkDownForceAging(rtk_uint32 *pEnable)
-{
-    rtk_uint32  value;
-    ret_t   retVal;
-
-    if ((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LUT_CFG, RTL8367C_LINKDOWN_AGEOUT_OFFSET, &value)) != RT_ERR_OK)
-        return retVal;
-
-    *pEnable = value ? 0 : 1;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicLutIpmcFwdRouterPort
- * Description:
- *       Set IPMC packet forward to rounter port also or not
- * Input:
- *      enable      - 1: Inlcude router port, 0, exclude router port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_ENABLE     Invalid parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLutIpmcFwdRouterPort(rtk_uint32 enable)
-{
-    if(enable > 1)
-        return RT_ERR_ENABLE;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_LUT_CFG2, RTL8367C_LUT_IPMC_FWD_RPORT_OFFSET, enable);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicLutIpmcFwdRouterPort
- * Description:
- *       Get IPMC packet forward to rounter port also or not
- * Input:
- *      None
- * Output:
- *      pEnable         - 1: Inlcude router port, 0, exclude router port
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLutIpmcFwdRouterPort(rtk_uint32 *pEnable)
-{
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_LUT_CFG2, RTL8367C_LUT_IPMC_FWD_RPORT_OFFSET, pEnable);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_meter.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_meter.c
deleted file mode 100644
index 5412591a82..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_meter.c
+++ /dev/null
@@ -1,305 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Shared meter related functions
- *
- */
-#include <rtl8367c_asicdrv_meter.h>
-/* Function Name:
- *      rtl8367c_setAsicShareMeter
- * Description:
- *      Set meter configuration
- * Input:
- *      index   - hared meter index (0-31)
- *      rate    - 17-bits rate of share meter, unit is 8Kpbs
- *      ifg     - Including IFG in rate calculation, 1:include 0:exclude
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicShareMeter(rtk_uint32 index, rtk_uint32 rate, rtk_uint32 ifg)
-{
-    ret_t retVal;
-
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(index < 32)
-    {
-    /*19-bits Rate*/
-        retVal = rtl8367c_setAsicReg(RTL8367C_METER_RATE_REG(index), rate&0xFFFF);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        retVal = rtl8367c_setAsicReg(RTL8367C_METER_RATE_REG(index) + 1, (rate &0x70000) >> 16);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        retVal = rtl8367c_setAsicRegBit(RTL8367C_METER_IFG_CTRL_REG(index), RTL8367C_METER_IFG_OFFSET(index), ifg);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-    /*19-bits Rate*/
-        retVal = rtl8367c_setAsicReg(RTL8367C_REG_METER32_RATE_CTRL0 + ((index-32) << 1), rate&0xFFFF);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        retVal = rtl8367c_setAsicReg(RTL8367C_REG_METER32_RATE_CTRL0 + ((index-32) << 1) + 1, (rate &0x70000) >> 16);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_METER_IFG_CTRL2 + ((index-32) >> 4), RTL8367C_METER_IFG_OFFSET(index), ifg);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicShareMeter
- * Description:
- *      Get meter configuration
- * Input:
- *      index   - hared meter index (0-31)
- *      pRate   - 17-bits rate of share meter, unit is 8Kpbs
- *      pIfg    - Including IFG in rate calculation, 1:include 0:exclude
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicShareMeter(rtk_uint32 index, rtk_uint32 *pRate, rtk_uint32 *pIfg)
-{
-    rtk_uint32 regData;
-    rtk_uint32 regData2;
-    ret_t retVal;
-
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(index < 32)
-    {
-    /*17-bits Rate*/
-     retVal = rtl8367c_getAsicReg(RTL8367C_METER_RATE_REG(index), &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-     retVal = rtl8367c_getAsicReg(RTL8367C_METER_RATE_REG(index) + 1, &regData2);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-    *pRate = ((regData2 << 16) & 0x70000) | regData;
-    /*IFG*/
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_METER_IFG_CTRL_REG(index), RTL8367C_METER_IFG_OFFSET(index), pIfg);
-
-    return retVal;
-    }
-    else
-    {
-    /*17-bits Rate*/
-     retVal = rtl8367c_getAsicReg(RTL8367C_REG_METER32_RATE_CTRL0 + ((index-32) << 1), &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-     retVal = rtl8367c_getAsicReg(RTL8367C_REG_METER32_RATE_CTRL0 + ((index-32) << 1) + 1, &regData2);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-    *pRate = ((regData2 << 16) & 0x70000) | regData;
-    /*IFG*/
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_METER_IFG_CTRL2 + ((index-32) >> 4), RTL8367C_METER_IFG_OFFSET(index), pIfg);
-
-    return retVal;
-    }
-}
-/* Function Name:
- *      rtl8367c_setAsicShareMeterBucketSize
- * Description:
- *      Set meter related leaky bucket threshold
- * Input:
- *      index       - hared meter index (0-31)
- *      lbthreshold - Leaky bucket threshold of meter
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicShareMeterBucketSize(rtk_uint32 index, rtk_uint32 lbthreshold)
-{
-
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(index < 32)
-    return rtl8367c_setAsicReg(RTL8367C_METER_BUCKET_SIZE_REG(index), lbthreshold);
-    else
-       return rtl8367c_setAsicReg(RTL8367C_REG_METER32_BUCKET_SIZE + index - 32, lbthreshold);
-}
-/* Function Name:
- *      rtl8367c_getAsicShareMeterBucketSize
- * Description:
- *      Get meter related leaky bucket threshold
- * Input:
- *      index       - hared meter index (0-31)
- *      pLbthreshold - Leaky bucket threshold of meter
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicShareMeterBucketSize(rtk_uint32 index, rtk_uint32 *pLbthreshold)
-{
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(index < 32)
-    return rtl8367c_getAsicReg(RTL8367C_METER_BUCKET_SIZE_REG(index), pLbthreshold);
-    else
-       return rtl8367c_getAsicReg(RTL8367C_REG_METER32_BUCKET_SIZE + index - 32, pLbthreshold);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicShareMeterType
- * Description:
- *      Set meter Type
- * Input:
- *      index       - shared meter index (0-31)
- *      Type        - 0: kbps, 1: pps
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicShareMeterType(rtk_uint32 index, rtk_uint32 type)
-{
-    rtk_uint32 reg;
-
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(index < 32)
-        reg = RTL8367C_REG_METER_MODE_SETTING0 + (index / 16);
-    else
-        reg = RTL8367C_REG_METER_MODE_SETTING2 + ((index - 32) / 16);
-    return rtl8367c_setAsicRegBit(reg, index % 16, type);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicShareMeterType
- * Description:
- *      Get meter Type
- * Input:
- *      index       - shared meter index (0-31)
- * Output:
- *      pType       - 0: kbps, 1: pps
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicShareMeterType(rtk_uint32 index, rtk_uint32 *pType)
-{
-    rtk_uint32 reg;
-
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(NULL == pType)
-        return RT_ERR_NULL_POINTER;
-
-    if(index < 32)
-        reg = RTL8367C_REG_METER_MODE_SETTING0 + (index / 16);
-    else
-        reg = RTL8367C_REG_METER_MODE_SETTING2 + ((index - 32) / 16);
-    return rtl8367c_getAsicRegBit(reg, index % 16, pType);
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicMeterExceedStatus
- * Description:
- *      Clear shared meter status
- * Input:
- *      index       - hared meter index (0-31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMeterExceedStatus(rtk_uint32 index)
-{
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(index < 32)
-        return rtl8367c_setAsicRegBit(RTL8367C_METER_OVERRATE_INDICATOR_REG(index), RTL8367C_METER_EXCEED_OFFSET(index), 1);
-    else
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_METER_OVERRATE_INDICATOR2 + ((index - 32) >> 4), RTL8367C_METER_EXCEED_OFFSET(index), 1);
-
-}
-/* Function Name:
- *      rtl8367c_getAsicMeterExceedStatus
- * Description:
- *      Get shared meter status
- * Input:
- *      index   - hared meter index (0-31)
- *      pStatus     - 0: rate doesn't exceed    1: rate exceeds
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      If rate is over rate*8Kbps of a meter, the state bit of this meter is set to 1.
- */
-ret_t rtl8367c_getAsicMeterExceedStatus(rtk_uint32 index, rtk_uint32* pStatus)
-{
-    if(index > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(index < 32)
-        return rtl8367c_getAsicRegBit(RTL8367C_METER_OVERRATE_INDICATOR_REG(index), RTL8367C_METER_EXCEED_OFFSET(index), pStatus);
-    else
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_METER_OVERRATE_INDICATOR2 + ((index - 32) >> 4), RTL8367C_METER_EXCEED_OFFSET(index), pStatus);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_mib.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_mib.c
deleted file mode 100644
index c9aaa01d3e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_mib.c
+++ /dev/null
@@ -1,570 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : MIB related functions
- *
- */
-
-#include <rtl8367c_asicdrv_mib.h>
-/* Function Name:
- *      rtl8367c_setAsicMIBsCounterReset
- * Description:
- *      Reset global/queue manage or per-port MIB counter
- * Input:
- *      greset  - Global reset
- *      qmreset - Queue maganement reset
- *      portmask    - Port reset mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsCounterReset(rtk_uint32 greset, rtk_uint32 qmreset, rtk_uint32 portmask)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint32 regBits;
-
-    regBits = RTL8367C_GLOBAL_RESET_MASK |
-                RTL8367C_QM_RESET_MASK |
-                    RTL8367C_MIB_PORT07_MASK |
-                    ((rtk_uint32)0x7 << 13);
-    regData = ((greset << RTL8367C_GLOBAL_RESET_OFFSET) & RTL8367C_GLOBAL_RESET_MASK) |
-                ((qmreset << RTL8367C_QM_RESET_OFFSET) & RTL8367C_QM_RESET_MASK) |
-                (((portmask & 0xFF) << RTL8367C_PORT0_RESET_OFFSET) & RTL8367C_MIB_PORT07_MASK) |
-                (((portmask >> 8)&0x7) << 13);
-
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_MIB_CTRL0, regBits, (regData >> RTL8367C_PORT0_RESET_OFFSET));
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicMIBsCounter
- * Description:
- *      Get MIBs counter
- * Input:
- *      port        - Physical port number (0~7)
- *      mibIdx      - MIB counter index
- *      pCounter    - MIB retrived counter
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_BUSYWAIT_TIMEOUT - MIB is busy at retrieving
- *      RT_ERR_STAT_CNTR_FAIL   - MIB is resetting
- * Note:
- *      Before MIBs counter retrieving, writting accessing address to ASIC at first and check the MIB
- *      control register status. If busy bit of MIB control is set, that means MIB counter have been
- *      waiting for preparing, then software must wait atfer this busy flag reset by ASIC. This driver
- *      did not recycle reading user desired counter. Software must use driver again to get MIB counter
- *      if return value is not RT_ERR_OK.
- */
-ret_t rtl8367c_getAsicMIBsCounter(rtk_uint32 port, RTL8367C_MIBCOUNTER mibIdx, rtk_uint64* pCounter)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-    rtk_uint32 regData;
-    rtk_uint32 mibAddr;
-    rtk_uint32 mibOff=0;
-
-    /* address offset to MIBs counter */
-    CONST rtk_uint16 mibLength[RTL8367C_MIBS_NUMBER]= {
-        4,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,
-        4,2,2,2,2,2,2,2,2,
-        4,2,2,2,2,2,2,2,2,2,2,2,2,2,2,
-        2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2};
-
-    rtk_uint16 i;
-    rtk_uint64 mibCounter;
-
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(mibIdx >= RTL8367C_MIBS_NUMBER)
-        return RT_ERR_STAT_INVALID_CNTR;
-
-    if(dot1dTpLearnedEntryDiscards == mibIdx)
-    {
-        mibAddr = RTL8367C_MIB_LEARNENTRYDISCARD_OFFSET;
-    }
-    else
-    {
-        i = 0;
-        mibOff = RTL8367C_MIB_PORT_OFFSET * port;
-
-        if(port > 7)
-            mibOff = mibOff + 68;
-
-        while(i < mibIdx)
-        {
-            mibOff += mibLength[i];
-            i++;
-        }
-
-        mibAddr = mibOff;
-    }
-
-
-    /*writing access counter address first*/
-    /*This address is SRAM address, and SRAM address = MIB register address >> 2*/
-    /*then ASIC will prepare 64bits counter wait for being retrived*/
-    /*Write Mib related address to access control register*/
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_MIB_ADDRESS, (mibAddr >> 2));
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-
-
-    /* polling busy flag */
-    i = 100;
-    while(i > 0)
-    {
-        /*read MIB control register*/
-        retVal = rtl8367c_getAsicReg(RTL8367C_MIB_CTRL_REG,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        if((regData & RTL8367C_MIB_CTRL0_BUSY_FLAG_MASK) == 0)
-        {
-            break;
-        }
-
-        i--;
-    }
-
-    if(regData & RTL8367C_MIB_CTRL0_BUSY_FLAG_MASK)
-        return RT_ERR_BUSYWAIT_TIMEOUT;
-
-    if(regData & RTL8367C_RESET_FLAG_MASK)
-        return RT_ERR_STAT_CNTR_FAIL;
-
-    mibCounter = 0;
-    i = mibLength[mibIdx];
-    if(4 == i)
-        regAddr = RTL8367C_MIB_COUNTER_BASE_REG + 3;
-    else
-        regAddr = RTL8367C_MIB_COUNTER_BASE_REG + ((mibOff + 1) % 4);
-
-    while(i)
-    {
-        retVal = rtl8367c_getAsicReg(regAddr, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        mibCounter = (mibCounter << 16) | (regData & 0xFFFF);
-
-        regAddr --;
-        i --;
-
-    }
-
-    *pCounter = mibCounter;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicMIBsLogCounter
- * Description:
- *      Get MIBs Loggin counter
- * Input:
- *      index       - The index of 32 logging counter (0 ~ 31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_ENTRY_INDEX      - Wrong index
- *      RT_ERR_BUSYWAIT_TIMEOUT - MIB is busy at retrieving
- *      RT_ERR_STAT_CNTR_FAIL   - MIB is resetting
- * Note:
- *      This API get 32 logging counter
- */
-ret_t rtl8367c_getAsicMIBsLogCounter(rtk_uint32 index, rtk_uint32 *pCounter)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-    rtk_uint32 regData;
-    rtk_uint32 mibAddr;
-    rtk_uint16 i;
-    rtk_uint64 mibCounter;
-
-    if(index > RTL8367C_MIB_MAX_LOG_CNT_IDX)
-        return RT_ERR_ENTRY_INDEX;
-
-    mibAddr = RTL8367C_MIB_LOG_CNT_OFFSET + ((index / 2) * 4);
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_MIB_ADDRESS, (mibAddr >> 2));
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /*read MIB control register*/
-    retVal = rtl8367c_getAsicReg(RTL8367C_MIB_CTRL_REG, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    if(regData & RTL8367C_MIB_CTRL0_BUSY_FLAG_MASK)
-        return RT_ERR_BUSYWAIT_TIMEOUT;
-
-    if(regData & RTL8367C_RESET_FLAG_MASK)
-        return RT_ERR_STAT_CNTR_FAIL;
-
-    mibCounter = 0;
-    if((index % 2) == 1)
-        regAddr = RTL8367C_MIB_COUNTER_BASE_REG + 3;
-    else
-        regAddr = RTL8367C_MIB_COUNTER_BASE_REG + 1;
-
-    for(i = 0; i <= 1; i++)
-    {
-        retVal = rtl8367c_getAsicReg(regAddr, &regData);
-
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        mibCounter = (mibCounter << 16) | (regData & 0xFFFF);
-
-        regAddr --;
-    }
-
-    *pCounter = mibCounter;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicMIBsControl
- * Description:
- *      Get MIB control register
- * Input:
- *      pMask       - MIB control status mask bit[0]-busy bit[1]
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      Software need to check this control register atfer doing port resetting or global resetting
- */
-ret_t rtl8367c_getAsicMIBsControl(rtk_uint32* pMask)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_MIB_CTRL_REG, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pMask = regData & (RTL8367C_MIB_CTRL0_BUSY_FLAG_MASK | RTL8367C_RESET_FLAG_MASK);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicMIBsResetValue
- * Description:
- *      Reset all counter to 0 or 1
- * Input:
- *      value           - Reset to value 0 or 1
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsResetValue(rtk_uint32 value)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIB_CTRL0, RTL8367C_RESET_VALUE_OFFSET, value);
-}
-/* Function Name:
- *      rtl8367c_getAsicMIBsResetValue
- * Description:
- *      Reset all counter to 0 or 1
- * Input:
- *      value           - Reset to value 0 or 1
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMIBsResetValue(rtk_uint32* value)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIB_CTRL0, RTL8367C_RESET_VALUE_OFFSET, value);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMIBsUsageMode
- * Description:
- *      MIB update mode
- * Input:
- *      mode            - 1: latch all MIBs by timer 0:normal free run counting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsUsageMode(rtk_uint32 mode)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIB_CTRL4, RTL8367C_MIB_USAGE_MODE_OFFSET, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicMIBsUsageMode
- * Description:
- *      MIB update mode
- * Input:
- *      pMode           - 1: latch all MIBs by timer 0:normal free run counting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMIBsUsageMode(rtk_uint32* pMode)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIB_CTRL4, RTL8367C_MIB_USAGE_MODE_OFFSET, pMode);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMIBsTimer
- * Description:
- *      MIB latching timer
- * Input:
- *      timer           - latch timer, unit 1 second
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsTimer(rtk_uint32 timer)
-{
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_MIB_CTRL4, RTL8367C_MIB_TIMER_MASK, timer);
-}
-/* Function Name:
- *      rtl8367c_getAsicMIBsTimer
- * Description:
- *      MIB latching timer
- * Input:
- *      pTimer          - latch timer, unit 1 second
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMIBsTimer(rtk_uint32* pTimer)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_MIB_CTRL4, RTL8367C_MIB_TIMER_MASK, pTimer);
-}
-/* Function Name:
- *      rtl8367c_setAsicMIBsLoggingMode
- * Description:
- *      MIB logging counter mode
- * Input:
- *      index   - logging counter mode index (0~15)
- *      mode    - 0:32-bits mode 1:64-bits mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsLoggingMode(rtk_uint32 index, rtk_uint32 mode)
-{
-    if(index > RTL8367C_MIB_MAX_LOG_MODE_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIB_CTRL3, index,mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicMIBsLoggingMode
- * Description:
- *      MIB logging counter mode
- * Input:
- *      index   - logging counter mode index (0~15)
- *      pMode   - 0:32-bits mode 1:64-bits mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMIBsLoggingMode(rtk_uint32 index, rtk_uint32* pMode)
-{
-    if(index > RTL8367C_MIB_MAX_LOG_MODE_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIB_CTRL3, index,pMode);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMIBsLoggingType
- * Description:
- *      MIB logging counter type
- * Input:
- *      index   - logging counter mode index (0~15)
- *      type    - 0:Packet count 1:Byte count
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsLoggingType(rtk_uint32 index, rtk_uint32 type)
-{
-    if(index > RTL8367C_MIB_MAX_LOG_MODE_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIB_CTRL5, index,type);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicMIBsLoggingType
- * Description:
- *      MIB logging counter type
- * Input:
- *      index   - logging counter mode index (0~15)
- *      pType   - 0:Packet count 1:Byte count
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMIBsLoggingType(rtk_uint32 index, rtk_uint32* pType)
-{
-    if(index > RTL8367C_MIB_MAX_LOG_MODE_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIB_CTRL5, index,pType);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMIBsResetLoggingCounter
- * Description:
- *      MIB logging counter type
- * Input:
- *      index   - logging counter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsResetLoggingCounter(rtk_uint32 index)
-{
-    ret_t retVal;
-
-    if(index > RTL8367C_MIB_MAX_LOG_CNT_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(index < 16)
-        retVal = rtl8367c_setAsicReg(RTL8367C_REG_MIB_CTRL1, 1<<index);
-    else
-        retVal = rtl8367c_setAsicReg(RTL8367C_REG_MIB_CTRL2, 1<<(index-16));
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMIBsLength
- * Description:
- *      Set MIB length couting mode
- * Input:
- *      txLengthMode    - 0: tag length doesn't be counted. 1: tag length is counted.
- *      rxLengthMode    - 0: tag length doesn't be counted. 1: tag length is counted.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMIBsLength(rtk_uint32 txLengthMode, rtk_uint32 rxLengthMode)
-{
-    ret_t retVal;
-
-    if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MIB_RMON_LEN_CTRL, RTL8367C_TX_LENGTH_CTRL_OFFSET, txLengthMode)) != RT_ERR_OK)
-        return retVal;
-
-    if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MIB_RMON_LEN_CTRL, RTL8367C_RX_LENGTH_CTRL_OFFSET, rxLengthMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMIBsLength
- * Description:
- *      Set MIB length couting mode
- * Input:
- *      None.
- * Output:
- *      pTxLengthMode - 0: tag length doesn't be counted. 1: tag length is counted.
- *      pRxLengthMode - 0: tag length doesn't be counted. 1: tag length is counted.
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_OUT_OF_RANGE     - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMIBsLength(rtk_uint32 *pTxLengthMode, rtk_uint32 *pRxLengthMode)
-{
-    ret_t retVal;
-
-    if( (retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_MIB_RMON_LEN_CTRL, RTL8367C_TX_LENGTH_CTRL_OFFSET, pTxLengthMode)) != RT_ERR_OK)
-        return retVal;
-
-    if( (retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_MIB_RMON_LEN_CTRL, RTL8367C_RX_LENGTH_CTRL_OFFSET, pRxLengthMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_mirror.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_mirror.c
deleted file mode 100644
index de945ff676..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_mirror.c
+++ /dev/null
@@ -1,472 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port mirror related functions
- *
- */
-#include <rtl8367c_asicdrv_mirror.h>
-/* Function Name:
- *      rtl8367c_setAsicPortMirror
- * Description:
- *      Set port mirror function
- * Input:
- *      source  - Source port
- *      monitor - Monitor (destination) port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirror(rtk_uint32 source, rtk_uint32 monitor)
-{
-    ret_t retVal;
-
-    if((source > RTL8367C_PORTIDMAX) || (monitor > RTL8367C_PORTIDMAX))
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_SOURCE_PORT_MASK, source);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-
-    return rtl8367c_setAsicRegBits(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_MONITOR_PORT_MASK, monitor);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirror
- * Description:
- *      Get port mirror function
- * Input:
- *      pSource     - Source port
- *      pMonitor - Monitor (destination) port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirror(rtk_uint32 *pSource, rtk_uint32 *pMonitor)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_SOURCE_PORT_MASK, pSource);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_MONITOR_PORT_MASK, pMonitor);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorRxFunction
- * Description:
- *      Set the mirror function on RX of the mirrored
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorRxFunction(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_RX_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorRxFunction
- * Description:
- *      Get the mirror function on RX of the mirrored
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorRxFunction(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_RX_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorTxFunction
- * Description:
- *      Set the mirror function on TX of the mirrored
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorTxFunction(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_TX_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorTxFunction
- * Description:
- *      Get the mirror function on TX of the mirrored
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorTxFunction(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_TX_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorIsolation
- * Description:
- *      Set the traffic isolation on monitor port
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorIsolation(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_ISO_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorIsolation
- * Description:
- *      Get the traffic isolation on monitor port
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorIsolation(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_MIRROR_CTRL_REG, RTL8367C_MIRROR_ISO_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorMask
- * Description:
- *      Set mirror source port mask
- * Input:
- *      SourcePortmask  - Source Portmask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_MASK- Port Mask Error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorMask(rtk_uint32 SourcePortmask)
-{
-    if( SourcePortmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_MIRROR_SRC_PMSK, RTL8367C_MIRROR_SRC_PMSK_MASK, SourcePortmask);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorMask
- * Description:
- *      Get mirror source port mask
- * Input:
- *      None
- * Output:
- *      pSourcePortmask     - Source Portmask
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_MASK- Port Mask Error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorMask(rtk_uint32 *pSourcePortmask)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_MIRROR_SRC_PMSK, RTL8367C_MIRROR_SRC_PMSK_MASK, pSourcePortmask);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorVlanRxLeaky
- * Description:
- *      Set the mirror function of VLAN RX leaky
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorVlanRxLeaky(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_RX_VLAN_LEAKY_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorVlanRxLeaky
- * Description:
- *      Get the mirror function of VLAN RX leaky
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorVlanRxLeaky(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_RX_VLAN_LEAKY_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorVlanTxLeaky
- * Description:
- *      Set the mirror function of VLAN TX leaky
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorVlanTxLeaky(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_TX_VLAN_LEAKY_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorVlanTxLeaky
- * Description:
- *      Get the mirror function of VLAN TX leaky
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorVlanTxLeaky(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_TX_VLAN_LEAKY_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorIsolationRxLeaky
- * Description:
- *      Set the mirror function of  Isolation RX leaky
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorIsolationRxLeaky(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_RX_ISOLATION_LEAKY_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorIsolationRxLeaky
- * Description:
- *      Get the mirror function of VLAN RX leaky
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorIsolationRxLeaky(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_RX_ISOLATION_LEAKY_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorIsolationTxLeaky
- * Description:
- *      Set the mirror function of Isolation TX leaky
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorIsolationTxLeaky(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_TX_ISOLATION_LEAKY_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorIsolationTxLeaky
- * Description:
- *      Get the mirror function of VLAN TX leaky
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorIsolationTxLeaky(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_TX_ISOLATION_LEAKY_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorRealKeep
- * Description:
- *      Set the mirror function of keep format
- * Input:
- *      mode    - 1: keep original format, 0: follow VLAN config
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorRealKeep(rtk_uint32 mode)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_REALKEEP_EN_OFFSET, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorRealKeep
- * Description:
- *      Get the mirror function of keep format
- * Input:
- *      pMode   - 1: keep original format, 0: follow VLAN config
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorRealKeep(rtk_uint32* pMode)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL2, RTL8367C_MIRROR_REALKEEP_EN_OFFSET, pMode);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortMirrorOverride
- * Description:
- *      Set the mirror function of override
- * Input:
- *      rxMirror    - 1: output rx Mirror format, 0: output forward format
- *      txMirror    - 1: output tx Mirror format, 0: output forward format
- *      aclMirror   - 1: output ACL Mirror format, 0: output forward format
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortMirrorOverride(rtk_uint32 rxMirror, rtk_uint32 txMirror, rtk_uint32 aclMirror)
-{
-    ret_t retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL3, RTL8367C_MIRROR_RX_OVERRIDE_EN_OFFSET, rxMirror)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL3, RTL8367C_MIRROR_TX_OVERRIDE_EN_OFFSET, txMirror)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MIRROR_CTRL3, RTL8367C_MIRROR_ACL_OVERRIDE_EN_OFFSET, aclMirror)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPortMirrorOverride
- * Description:
- *      Get the mirror function of override
- * Input:
- *      None
- * Output:
- *      pRxMirror   - 1: output rx Mirror format, 0: output forward format
- *      pTxMirror   - 1: output tx Mirror format, 0: output forward format
- *      pAclMirror  - 1: output ACL Mirror format, 0: output forward format
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortMirrorOverride(rtk_uint32 *pRxMirror, rtk_uint32 *pTxMirror, rtk_uint32 *pAclMirror)
-{
-    ret_t retVal;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL3, RTL8367C_MIRROR_RX_OVERRIDE_EN_OFFSET, pRxMirror)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL3, RTL8367C_MIRROR_TX_OVERRIDE_EN_OFFSET, pTxMirror)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_MIRROR_CTRL3, RTL8367C_MIRROR_ACL_OVERRIDE_EN_OFFSET, pAclMirror)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_misc.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_misc.c
deleted file mode 100644
index 2189b151c3..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_misc.c
+++ /dev/null
@@ -1,268 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Miscellaneous functions
- *
- */
-
-#include <rtl8367c_asicdrv_misc.h>
-/* Function Name:
- *      rtl8367c_setAsicMacAddress
- * Description:
- *      Set switch MAC address
- * Input:
- *      mac     - switch mac
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMacAddress(ether_addr_t mac)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint8 *accessPtr;
-    rtk_uint32 i;
-
-    accessPtr =  (rtk_uint8*)&mac;
-
-    regData = *accessPtr;
-    accessPtr ++;
-    regData = (regData << 8) | *accessPtr;
-    accessPtr ++;
-    for(i = 0; i <=2; i++)
-    {
-        retVal = rtl8367c_setAsicReg(RTL8367C_REG_SWITCH_MAC2 - i, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        regData = *accessPtr;
-        accessPtr ++;
-        regData = (regData << 8) | *accessPtr;
-        accessPtr ++;
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicMacAddress
- * Description:
- *      Get switch MAC address
- * Input:
- *      pMac    - switch mac
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMacAddress(ether_addr_t *pMac)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint8 *accessPtr;
-    rtk_uint32 i;
-
-
-    accessPtr = (rtk_uint8*)pMac;
-
-    for(i = 0; i <= 2; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_REG_SWITCH_MAC2 - i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *accessPtr = (regData & 0xFF00) >> 8;
-        accessPtr ++;
-        *accessPtr = regData & 0xFF;
-        accessPtr ++;
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicDebugInfo
- * Description:
- *      Get per-port packet forward debugging information
- * Input:
- *      port        - Physical port number (0~7)
- *      pDebugifo   - per-port packet trap/drop/forward reason
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicDebugInfo(rtk_uint32 port, rtk_uint32 *pDebugifo)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_DEBUG_INFO_REG(port), RTL8367C_DEBUG_INFO_MASK(port), pDebugifo);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortJamMode
- * Description:
- *      Set half duplex flow control setting
- * Input:
- *      mode    - 0: Back-Pressure 1: DEFER
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortJamMode(rtk_uint32 mode)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_CFG_BACKPRESSURE, RTL8367C_LONGTXE_OFFSET,mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortJamMode
- * Description:
- *      Get half duplex flow control setting
- * Input:
- *      pMode   - 0: Back-Pressure 1: DEFER
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortJamMode(rtk_uint32* pMode)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_CFG_BACKPRESSURE, RTL8367C_LONGTXE_OFFSET, pMode);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMaxLengthCfg
- * Description:
- *      Set Max packet length configuration
- * Input:
- *      cfgId       - Configuration ID
- *      maxLength   - Max Length
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMaxLengthCfg(rtk_uint32 cfgId, rtk_uint32 maxLength)
-{
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_MAX_LEN_RX_TX_CFG0 + cfgId, RTL8367C_MAX_LEN_RX_TX_CFG0_MASK, maxLength);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicMaxLengthCfg
- * Description:
- *      Get Max packet length configuration
- * Input:
- *      cfgId       - Configuration ID
- *      maxLength   - Max Length
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMaxLengthCfg(rtk_uint32 cfgId, rtk_uint32 *pMaxLength)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_MAX_LEN_RX_TX_CFG0 + cfgId, RTL8367C_MAX_LEN_RX_TX_CFG0_MASK, pMaxLength);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicMaxLength
- * Description:
- *      Set Max packet length
- * Input:
- *      port        - port ID
- *      type        - 0: 10M/100M speed, 1: giga speed
- *      cfgId       - Configuration ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicMaxLength(rtk_uint32 port, rtk_uint32 type, rtk_uint32 cfgId)
-{
-    ret_t retVal;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MAX_LENGTH_CFG, (type * 8) + port, cfgId);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MAX_LENGTH_CFG_EXT, (type * 3) + port - 8, cfgId);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicMaxLength
- * Description:
- *      Get Max packet length
- * Input:
- *      port        - port ID
- *      type        - 0: 10M/100M speed, 1: giga speed
- *      cfgId       - Configuration ID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicMaxLength(rtk_uint32 port, rtk_uint32 type, rtk_uint32 *pCfgId)
-{
-    ret_t retVal;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_MAX_LENGTH_CFG, (type * 8) + port, pCfgId);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_MAX_LENGTH_CFG_EXT, (type * 3) + port - 8, pCfgId);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_oam.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_oam.c
deleted file mode 100644
index 1556f4500d..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_oam.c
+++ /dev/null
@@ -1,194 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 42321 $
- * $Date: 2013-08-26 13:51:29 +0800 (週一, 26 八月 2013) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : OAM related functions
- *
- */
-
-#include <rtl8367c_asicdrv_oam.h>
-/* Function Name:
- *      rtl8367c_setAsicOamParser
- * Description:
- *      Set OAM parser state
- * Input:
- *      port    - Physical port number (0~7)
- *      parser  - Per-Port OAM parser state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_NOT_ALLOWED  - Invalid paser state
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicOamParser(rtk_uint32 port, rtk_uint32 parser)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(parser > OAM_PARFWDCPU)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_OAM_PARSER_CTRL0 + port/8, RTL8367C_OAM_PARSER_MASK(port % 8), parser);
-}
-/* Function Name:
- *      rtl8367c_getAsicOamParser
- * Description:
- *      Get OAM parser state
- * Input:
- *      port    - Physical port number (0~7)
- *      pParser     - Per-Port OAM parser state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicOamParser(rtk_uint32 port, rtk_uint32* pParser)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_OAM_PARSER_CTRL0 + port/8, RTL8367C_OAM_PARSER_MASK(port%8), pParser);
-}
-/* Function Name:
- *      rtl8367c_setAsicOamMultiplexer
- * Description:
- *      Set OAM multiplexer state
- * Input:
- *      port        - Physical port number (0~7)
- *      multiplexer - Per-Port OAM multiplexer state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_NOT_ALLOWED  - Invalid multiplexer state
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicOamMultiplexer(rtk_uint32 port, rtk_uint32 multiplexer)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(multiplexer > OAM_MULCPU)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_OAM_MULTIPLEXER_CTRL0 + port/8, RTL8367C_OAM_MULTIPLEXER_MASK(port%8), multiplexer);
-}
-/* Function Name:
- *      rtl8367c_getAsicOamMultiplexer
- * Description:
- *      Get OAM multiplexer state
- * Input:
- *      port        - Physical port number (0~7)
- *      pMultiplexer - Per-Port OAM multiplexer state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicOamMultiplexer(rtk_uint32 port, rtk_uint32* pMultiplexer)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_OAM_MULTIPLEXER_CTRL0 + port/8, RTL8367C_OAM_MULTIPLEXER_MASK(port%8), pMultiplexer);
-}
-/* Function Name:
- *      rtl8367c_setAsicOamCpuPri
- * Description:
- *      Set trap priority for OAM packet
- * Input:
- *      priority    - priority (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY     - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicOamCpuPri(rtk_uint32 priority)
-{
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_QOS_TRAP_PRIORITY0, RTL8367C_OAM_PRIOIRTY_MASK, priority);
-}
-/* Function Name:
- *      rtl8367c_getAsicOamCpuPri
- * Description:
- *      Get trap priority for OAM packet
- * Input:
- *      pPriority   - priority (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicOamCpuPri(rtk_uint32 *pPriority)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_QOS_TRAP_PRIORITY0, RTL8367C_OAM_PRIOIRTY_MASK, pPriority);
-}
-/* Function Name:
- *      rtl8367c_setAsicOamEnable
- * Description:
- *      Set OAM function state
- * Input:
- *      enabled     - OAM function usage 1:enable, 0:disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicOamEnable(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_OAM_CTRL, RTL8367C_OAM_CTRL_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicOamEnable
- * Description:
- *      Get OAM function state
- * Input:
- *      pEnabled    - OAM function usage 1:enable, 0:disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicOamEnable(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_OAM_CTRL, RTL8367C_OAM_CTRL_OFFSET, pEnabled);
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_phy.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_phy.c
deleted file mode 100644
index fb4db113a9..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_phy.c
+++ /dev/null
@@ -1,394 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : PHY related functions
- *
- */
-#include <rtl8367c_asicdrv_phy.h>
-
-#if defined(MDC_MDIO_OPERATION)
-/* Function Name:
- *      rtl8367c_setAsicPHYOCPReg
- * Description:
- *      Set PHY OCP registers
- * Input:
- *      phyNo   - Physical port number (0~7)
- *      ocpAddr - OCP address
- *      ocpData - Writing data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PHY_REG_ID       - invalid PHY address
- *      RT_ERR_PHY_ID           - invalid PHY no
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPHYOCPReg(rtk_uint32 phyNo, rtk_uint32 ocpAddr, rtk_uint32 ocpData )
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-    rtk_uint32 ocpAddrPrefix, ocpAddr9_6, ocpAddr5_1;
-
-    /* OCP prefix */
-    ocpAddrPrefix = ((ocpAddr & 0xFC00) >> 10);
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_GPHY_OCP_MSB_0, RTL8367C_CFG_CPU_OCPADR_MSB_MASK, ocpAddrPrefix)) != RT_ERR_OK)
-        return retVal;
-
-    /*prepare access address*/
-    ocpAddr9_6 = ((ocpAddr >> 6) & 0x000F);
-    ocpAddr5_1 = ((ocpAddr >> 1) & 0x001F);
-    regAddr = RTL8367C_PHY_BASE | (ocpAddr9_6 << 8) | (phyNo << RTL8367C_PHY_OFFSET) | ocpAddr5_1;
-    if((retVal = rtl8367c_setAsicReg(regAddr, ocpData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPHYOCPReg
- * Description:
- *      Get PHY OCP registers
- * Input:
- *      phyNo   - Physical port number (0~7)
- *      ocpAddr - PHY address
- *      pRegData - read data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PHY_REG_ID       - invalid PHY address
- *      RT_ERR_PHY_ID           - invalid PHY no
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPHYOCPReg(rtk_uint32 phyNo, rtk_uint32 ocpAddr, rtk_uint32 *pRegData )
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-    rtk_uint32 ocpAddrPrefix, ocpAddr9_6, ocpAddr5_1;
-    /* OCP prefix */
-    ocpAddrPrefix = ((ocpAddr & 0xFC00) >> 10);
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_GPHY_OCP_MSB_0, RTL8367C_CFG_CPU_OCPADR_MSB_MASK, ocpAddrPrefix)) != RT_ERR_OK)
-        return retVal;
-
-    /*prepare access address*/
-    ocpAddr9_6 = ((ocpAddr >> 6) & 0x000F);
-    ocpAddr5_1 = ((ocpAddr >> 1) & 0x001F);
-    regAddr = RTL8367C_PHY_BASE | (ocpAddr9_6 << 8) | (phyNo << RTL8367C_PHY_OFFSET) | ocpAddr5_1;
-    if((retVal = rtl8367c_getAsicReg(regAddr, pRegData)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-#else
-
-/* Function Name:
- *      rtl8367c_setAsicPHYOCPReg
- * Description:
- *      Set PHY OCP registers
- * Input:
- *      phyNo   - Physical port number (0~7)
- *      ocpAddr - OCP address
- *      ocpData - Writing data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PHY_REG_ID       - invalid PHY address
- *      RT_ERR_PHY_ID           - invalid PHY no
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPHYOCPReg(rtk_uint32 phyNo, rtk_uint32 ocpAddr, rtk_uint32 ocpData )
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint32 busyFlag, checkCounter;
-    rtk_uint32 ocpAddrPrefix, ocpAddr9_6, ocpAddr5_1;
-
-    /*Check internal phy access busy or not*/
-    /*retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_INDRECT_ACCESS_STATUS, RTL8367C_INDRECT_ACCESS_STATUS_OFFSET,&busyFlag);*/
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_INDRECT_ACCESS_STATUS,&busyFlag);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    if(busyFlag)
-        return RT_ERR_BUSYWAIT_TIMEOUT;
-
-    /* OCP prefix */
-    ocpAddrPrefix = ((ocpAddr & 0xFC00) >> 10);
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_GPHY_OCP_MSB_0, RTL8367C_CFG_CPU_OCPADR_MSB_MASK, ocpAddrPrefix)) != RT_ERR_OK)
-        return retVal;
-
-    /*prepare access data*/
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_INDRECT_ACCESS_WRITE_DATA, ocpData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /*prepare access address*/
-    ocpAddr9_6 = ((ocpAddr >> 6) & 0x000F);
-    ocpAddr5_1 = ((ocpAddr >> 1) & 0x001F);
-    regData = RTL8367C_PHY_BASE | (ocpAddr9_6 << 8) | (phyNo << RTL8367C_PHY_OFFSET) | ocpAddr5_1;
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_INDRECT_ACCESS_ADDRESS, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /*Set WRITE Command*/
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_INDRECT_ACCESS_CTRL, RTL8367C_CMD_MASK | RTL8367C_RW_MASK);
-
-    checkCounter = 100;
-    while(checkCounter)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_REG_INDRECT_ACCESS_STATUS,&busyFlag);
-        if((retVal != RT_ERR_OK) || busyFlag)
-        {
-            checkCounter --;
-            if(0 == checkCounter)
-                return RT_ERR_BUSYWAIT_TIMEOUT;
-        }
-        else
-        {
-            checkCounter = 0;
-        }
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicPHYOCPReg
- * Description:
- *      Get PHY OCP registers
- * Input:
- *      phyNo   - Physical port number (0~7)
- *      ocpAddr - PHY address
- *      pRegData - read data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PHY_REG_ID       - invalid PHY address
- *      RT_ERR_PHY_ID           - invalid PHY no
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPHYOCPReg(rtk_uint32 phyNo, rtk_uint32 ocpAddr, rtk_uint32 *pRegData )
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint32 busyFlag,checkCounter;
-    rtk_uint32 ocpAddrPrefix, ocpAddr9_6, ocpAddr5_1;
-    /*Check internal phy access busy or not*/
-    /*retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_INDRECT_ACCESS_STATUS, RTL8367C_INDRECT_ACCESS_STATUS_OFFSET,&busyFlag);*/
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_INDRECT_ACCESS_STATUS,&busyFlag);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    if(busyFlag)
-        return RT_ERR_BUSYWAIT_TIMEOUT;
-
-    /* OCP prefix */
-    ocpAddrPrefix = ((ocpAddr & 0xFC00) >> 10);
-    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_GPHY_OCP_MSB_0, RTL8367C_CFG_CPU_OCPADR_MSB_MASK, ocpAddrPrefix)) != RT_ERR_OK)
-        return retVal;
-
-    /*prepare access address*/
-    ocpAddr9_6 = ((ocpAddr >> 6) & 0x000F);
-    ocpAddr5_1 = ((ocpAddr >> 1) & 0x001F);
-    regData = RTL8367C_PHY_BASE | (ocpAddr9_6 << 8) | (phyNo << RTL8367C_PHY_OFFSET) | ocpAddr5_1;
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_INDRECT_ACCESS_ADDRESS, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /*Set READ Command*/
-    retVal = rtl8367c_setAsicReg(RTL8367C_REG_INDRECT_ACCESS_CTRL, RTL8367C_CMD_MASK );
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    checkCounter = 100;
-    while(checkCounter)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_REG_INDRECT_ACCESS_STATUS,&busyFlag);
-        if((retVal != RT_ERR_OK) || busyFlag)
-        {
-            checkCounter --;
-            if(0 == checkCounter)
-                return RT_ERR_FAILED;
-        }
-        else
-        {
-            checkCounter = 0;
-        }
-    }
-
-    /*get PHY register*/
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_INDRECT_ACCESS_READ_DATA, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *pRegData = regData;
-
-    return RT_ERR_OK;
-}
-
-#endif
-
-/* Function Name:
- *      rtl8367c_setAsicPHYReg
- * Description:
- *      Set PHY registers
- * Input:
- *      phyNo   - Physical port number (0~7)
- *      phyAddr - PHY address (0~31)
- *      phyData - Writing data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PHY_REG_ID       - invalid PHY address
- *      RT_ERR_PHY_ID           - invalid PHY no
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPHYReg(rtk_uint32 phyNo, rtk_uint32 phyAddr, rtk_uint32 phyData )
-{
-    rtk_uint32 ocp_addr;
-
-    if(phyAddr > RTL8367C_PHY_REGNOMAX)
-        return RT_ERR_PHY_REG_ID;
-
-    ocp_addr = 0xa400 + phyAddr*2;
-
-    return rtl8367c_setAsicPHYOCPReg(phyNo, ocp_addr, phyData);
-}
-/* Function Name:
- *      rtl8367c_getAsicPHYReg
- * Description:
- *      Get PHY registers
- * Input:
- *      phyNo   - Physical port number (0~7)
- *      phyAddr - PHY address (0~31)
- *      pRegData - Writing data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PHY_REG_ID       - invalid PHY address
- *      RT_ERR_PHY_ID           - invalid PHY no
- *      RT_ERR_BUSYWAIT_TIMEOUT - PHY access busy
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPHYReg(rtk_uint32 phyNo, rtk_uint32 phyAddr, rtk_uint32 *pRegData )
-{
-    rtk_uint32 ocp_addr;
-
-    if(phyAddr > RTL8367C_PHY_REGNOMAX)
-        return RT_ERR_PHY_REG_ID;
-
-    ocp_addr = 0xa400 + phyAddr*2;
-
-    return rtl8367c_getAsicPHYOCPReg(phyNo, ocp_addr, pRegData);
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicSdsReg
- * Description:
- *      Set Serdes registers
- * Input:
- *      sdsId   - sdsid (0~1)
- *      sdsReg - reg address (0~31)
- *      sdsPage - Writing data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
-
- * Note:
- *      None
- */
-
-ret_t rtl8367c_setAsicSdsReg(rtk_uint32 sdsId, rtk_uint32 sdsReg, rtk_uint32 sdsPage,  rtk_uint32 value)
-{
-    rtk_uint32 retVal;
-
-    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, value)) != RT_ERR_OK)
-        return retVal;
-
-    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (sdsPage<<5) | sdsReg)) != RT_ERR_OK)
-        return retVal;
-
-    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0|sdsId)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtl8367c_getAiscSdsReg
- * Description:
- *      Get Serdes registers
- * Input:
- *      sdsId   - sdsid (0~1)
- *      sdsReg - reg address (0~31)
- *      sdsPage - Writing data
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
-
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSdsReg(rtk_uint32 sdsId, rtk_uint32 sdsReg, rtk_uint32 sdsPage, rtk_uint32 *value)
-{
-    rtk_uint32 retVal, busy;
-
-    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (sdsPage<<5) | sdsReg)) != RT_ERR_OK)
-        return retVal;
-
-    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x0080|sdsId)) != RT_ERR_OK)
-        return retVal;
-
-    while(1)
-    {
-        if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_SDS_INDACS_CMD, &busy))!=RT_ERR_OK)
-            return retVal;
-
-        if ((busy & 0x100) == 0)
-            break;
-    }
-
-    if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_SDS_INDACS_DATA, value))!=RT_ERR_OK)
-            return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_port.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_port.c
deleted file mode 100644
index 78e80a0b20..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_port.c
+++ /dev/null
@@ -1,5752 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76333 $
- * $Date: 2017-03-09 09:33:15 +0800 (週四, 09 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port security related functions
- *
- */
-
-#include <rtl8367c_asicdrv_port.h>
-
-#include <string.h>
-
-
-#define FIBER2_AUTO_INIT_SIZE 2038
-rtk_uint8 Fiber2_Auto[FIBER2_AUTO_INIT_SIZE] = {
-0x02,0x05,0x8F,0xE4,0xF5,0xA8,0xD2,0xAF,
-0x22,0x00,0x00,0x02,0x07,0x2C,0xC5,0xF0,
-0xF8,0xA3,0xE0,0x28,0xF0,0xC5,0xF0,0xF8,
-0xE5,0x82,0x15,0x82,0x70,0x02,0x15,0x83,
-0xE0,0x38,0xF0,0x22,0x75,0xF0,0x08,0x75,
-0x82,0x00,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xCD,0x33,0xCD,0xCC,0x33,0xCC,0xC5,0x82,
-0x33,0xC5,0x82,0x9B,0xED,0x9A,0xEC,0x99,
-0xE5,0x82,0x98,0x40,0x0C,0xF5,0x82,0xEE,
-0x9B,0xFE,0xED,0x9A,0xFD,0xEC,0x99,0xFC,
-0x0F,0xD5,0xF0,0xD6,0xE4,0xCE,0xFB,0xE4,
-0xCD,0xFA,0xE4,0xCC,0xF9,0xA8,0x82,0x22,
-0xB8,0x00,0xC1,0xB9,0x00,0x59,0xBA,0x00,
-0x2D,0xEC,0x8B,0xF0,0x84,0xCF,0xCE,0xCD,
-0xFC,0xE5,0xF0,0xCB,0xF9,0x78,0x18,0xEF,
-0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,0xFD,
-0xEC,0x33,0xFC,0xEB,0x33,0xFB,0x10,0xD7,
-0x03,0x99,0x40,0x04,0xEB,0x99,0xFB,0x0F,
-0xD8,0xE5,0xE4,0xF9,0xFA,0x22,0x78,0x18,
-0xEF,0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,
-0xFD,0xEC,0x33,0xFC,0xC9,0x33,0xC9,0x10,
-0xD7,0x05,0x9B,0xE9,0x9A,0x40,0x07,0xEC,
-0x9B,0xFC,0xE9,0x9A,0xF9,0x0F,0xD8,0xE0,
-0xE4,0xC9,0xFA,0xE4,0xCC,0xFB,0x22,0x75,
-0xF0,0x10,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xED,0x33,0xFD,0xCC,0x33,0xCC,0xC8,0x33,
-0xC8,0x10,0xD7,0x07,0x9B,0xEC,0x9A,0xE8,
-0x99,0x40,0x0A,0xED,0x9B,0xFD,0xEC,0x9A,
-0xFC,0xE8,0x99,0xF8,0x0F,0xD5,0xF0,0xDA,
-0xE4,0xCD,0xFB,0xE4,0xCC,0xFA,0xE4,0xC8,
-0xF9,0x22,0xEB,0x9F,0xF5,0xF0,0xEA,0x9E,
-0x42,0xF0,0xE9,0x9D,0x42,0xF0,0xE8,0x9C,
-0x45,0xF0,0x22,0xE0,0xFC,0xA3,0xE0,0xFD,
-0xA3,0xE0,0xFE,0xA3,0xE0,0xFF,0x22,0xE0,
-0xF8,0xA3,0xE0,0xF9,0xA3,0xE0,0xFA,0xA3,
-0xE0,0xFB,0x22,0xEC,0xF0,0xA3,0xED,0xF0,
-0xA3,0xEE,0xF0,0xA3,0xEF,0xF0,0x22,0x7D,
-0xD7,0x7C,0x04,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xAB,0x7D,0x80,0x7C,0x04,0x7F,0x01,
-0x7E,0x66,0x12,0x07,0xAB,0x7D,0xC0,0x7C,
-0x00,0x7F,0x00,0x7E,0x66,0x12,0x07,0xAB,
-0x7D,0x94,0x7C,0xF9,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0xAB,0x7D,0x81,0x7C,0x04,0x7F,
-0x01,0x7E,0x66,0x12,0x07,0xAB,0x7D,0xC0,
-0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0xA2,0x7C,0x31,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0xAB,0x7D,0x82,0x7C,0x04,
-0x7F,0x01,0x7E,0x66,0x12,0x07,0xAB,0x7D,
-0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,
-0x07,0xAB,0x7D,0x60,0x7C,0x69,0x7F,0x02,
-0x7E,0x66,0x12,0x07,0xAB,0x7D,0x83,0x7C,
-0x04,0x7F,0x01,0x7E,0x66,0x12,0x07,0xAB,
-0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,
-0x12,0x07,0xAB,0x7D,0x28,0x7C,0x97,0x7F,
-0x02,0x7E,0x66,0x12,0x07,0xAB,0x7D,0x84,
-0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xAB,0x7D,0x85,0x7C,0x9D,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0xAB,0x7D,
-0x23,0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xAB,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xAB,0x7D,0x10,0x7C,
-0xD8,0x7F,0x02,0x7E,0x66,0x12,0x07,0xAB,
-0x7D,0x24,0x7C,0x04,0x7F,0x01,0x7E,0x66,
-0x12,0x07,0xAB,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x12,0x07,0xAB,0x7D,0x00,
-0x7C,0x04,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0x2F,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xAB,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x02,0x07,0xAB,0x7D,
-0x03,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xAB,0x7D,0x80,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xAB,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0x66,0xEF,0x44,0x40,0xFD,
-0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xAB,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xAB,0x7D,
-0x03,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xAB,0x7D,0x80,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xAB,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0x66,0xEF,0x54,0xBF,0xFD,
-0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xAB,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xAB,0xE4,
-0xFD,0xFC,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0x80,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xAB,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0x66,0xEF,0x54,0xFD,0x54,0xFE,
-0xFD,0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xAB,0xE4,0xFD,0xFC,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xAB,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xAB,0xE4,
-0xFD,0xFC,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0x80,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xAB,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0x66,0xEF,0x44,0x02,0x44,0x01,
-0xFD,0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xAB,0xE4,0xFD,0xFC,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xAB,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x02,0x07,0xAB,0xE4,
-0x90,0x06,0x2C,0xF0,0xFD,0x7C,0x01,0x7F,
-0x3F,0x7E,0x1D,0x12,0x07,0xAB,0x7D,0x40,
-0x7C,0x00,0x7F,0x36,0x7E,0x13,0x12,0x07,
-0xAB,0xE4,0xFF,0xFE,0xFD,0x80,0x25,0xE4,
-0x7F,0xFF,0x7E,0xFF,0xFD,0xFC,0x90,0x06,
-0x24,0x12,0x01,0x0F,0xC3,0x12,0x00,0xF2,
-0x50,0x1B,0x90,0x06,0x24,0x12,0x01,0x03,
-0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,0xE4,
-0x3D,0xFD,0xE4,0x3C,0xFC,0x90,0x06,0x24,
-0x12,0x01,0x1B,0x80,0xD2,0xE4,0xF5,0xA8,
-0xD2,0xAF,0x7D,0x1F,0xFC,0x7F,0x49,0x7E,
-0x13,0x12,0x07,0xAB,0x12,0x07,0xDB,0x12,
-0x01,0x27,0x12,0x06,0x1B,0x12,0x07,0x8A,
-0x12,0x06,0xEA,0x7D,0x41,0x7C,0x00,0x7F,
-0x36,0x7E,0x13,0x12,0x07,0xAB,0xE4,0xFF,
-0xFE,0xFD,0x80,0x26,0x7F,0xFF,0x7E,0xFF,
-0x7D,0x05,0x7C,0x00,0x90,0x06,0x24,0x12,
-0x01,0x0F,0xC3,0x12,0x00,0xF2,0x50,0x1B,
-0x90,0x06,0x24,0x12,0x01,0x03,0xEF,0x24,
-0x01,0xFF,0xE4,0x3E,0xFE,0xE4,0x3D,0xFD,
-0xE4,0x3C,0xFC,0x90,0x06,0x24,0x12,0x01,
-0x1B,0x80,0xD1,0xC2,0x00,0xC2,0x01,0xD2,
-0xA9,0xD2,0x8C,0x7F,0x01,0x7E,0x62,0x12,
-0x07,0x66,0xEF,0x30,0xE2,0x07,0xE4,0x90,
-0x06,0x2C,0xF0,0x80,0xEE,0x90,0x06,0x2C,
-0xE0,0x70,0x12,0x12,0x04,0xF0,0x90,0x06,
-0x2C,0x74,0x01,0xF0,0xE4,0x90,0x06,0x33,
-0xF0,0xA3,0xF0,0x80,0xD6,0xC3,0x90,0x06,
-0x34,0xE0,0x94,0x62,0x90,0x06,0x33,0xE0,
-0x94,0x00,0x40,0xC7,0xE4,0xF0,0xA3,0xF0,
-0x12,0x04,0xF0,0x90,0x06,0x2C,0x74,0x01,
-0xF0,0x80,0xB8,0x75,0x0F,0x80,0x75,0x0E,
-0x7E,0x75,0x0D,0xAA,0x75,0x0C,0x83,0xE4,
-0xF5,0x10,0x7F,0x36,0x7E,0x13,0x12,0x07,
-0x66,0xEE,0xC4,0xF8,0x54,0xF0,0xC8,0xEF,
-0xC4,0x54,0x0F,0x48,0x54,0x07,0xFB,0x7A,
-0x00,0xEA,0x70,0x4A,0xEB,0x14,0x60,0x1C,
-0x14,0x60,0x27,0x24,0xFE,0x60,0x31,0x14,
-0x60,0x3C,0x24,0x05,0x70,0x38,0x75,0x0B,
-0x00,0x75,0x0A,0xC2,0x75,0x09,0xEB,0x75,
-0x08,0x0B,0x80,0x36,0x75,0x0B,0x40,0x75,
-0x0A,0x59,0x75,0x09,0x73,0x75,0x08,0x07,
-0x80,0x28,0x75,0x0B,0x00,0x75,0x0A,0xE1,
-0x75,0x09,0xF5,0x75,0x08,0x05,0x80,0x1A,
-0x75,0x0B,0xA0,0x75,0x0A,0xAC,0x75,0x09,
-0xB9,0x75,0x08,0x03,0x80,0x0C,0x75,0x0B,
-0x00,0x75,0x0A,0x62,0x75,0x09,0x3D,0x75,
-0x08,0x01,0x75,0x89,0x11,0xE4,0x7B,0x60,
-0x7A,0x09,0xF9,0xF8,0xAF,0x0B,0xAE,0x0A,
-0xAD,0x09,0xAC,0x08,0x12,0x00,0x60,0xAA,
-0x06,0xAB,0x07,0xC3,0xE4,0x9B,0xFB,0xE4,
-0x9A,0xFA,0x78,0x17,0xF6,0xAF,0x03,0xEF,
-0x08,0xF6,0x18,0xE6,0xF5,0x8C,0x08,0xE6,
-0xF5,0x8A,0x74,0x0D,0x2B,0xFB,0xE4,0x3A,
-0x18,0xF6,0xAF,0x03,0xEF,0x08,0xF6,0x75,
-0x88,0x10,0x53,0x8E,0xC7,0xD2,0xA9,0x22,
-0x7F,0x10,0x7E,0x13,0x12,0x07,0x66,0x90,
-0x06,0x2D,0xEE,0xF0,0xA3,0xEF,0xF0,0xEE,
-0x44,0x10,0xFE,0x90,0x06,0x2D,0xF0,0xA3,
-0xEF,0xF0,0x54,0xEF,0xFF,0x90,0x06,0x2D,
-0xEE,0xF0,0xFC,0xA3,0xEF,0xF0,0xFD,0x7F,
-0x10,0x7E,0x13,0x12,0x07,0xAB,0xE4,0xFF,
-0xFE,0x0F,0xBF,0x00,0x01,0x0E,0xEF,0x64,
-0x64,0x4E,0x70,0xF5,0x7D,0x04,0x7C,0x00,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0xAB,0x7D,
-0x00,0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xAB,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xAB,0xE4,0xFD,0xFC,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0xAB,0x7D,
-0x00,0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xAB,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xAB,0x7F,0x10,0x7E,
-0x13,0x12,0x07,0x66,0x90,0x06,0x2D,0xEE,
-0xF0,0xA3,0xEF,0xF0,0xEE,0x54,0xEF,0x90,
-0x06,0x2D,0xF0,0xFC,0xA3,0xEF,0xF0,0xFD,
-0x7F,0x10,0x7E,0x13,0x02,0x07,0xAB,0x78,
-0x7F,0xE4,0xF6,0xD8,0xFD,0x75,0x81,0x3C,
-0x02,0x05,0xD6,0x02,0x03,0x2F,0xE4,0x93,
-0xA3,0xF8,0xE4,0x93,0xA3,0x40,0x03,0xF6,
-0x80,0x01,0xF2,0x08,0xDF,0xF4,0x80,0x29,
-0xE4,0x93,0xA3,0xF8,0x54,0x07,0x24,0x0C,
-0xC8,0xC3,0x33,0xC4,0x54,0x0F,0x44,0x20,
-0xC8,0x83,0x40,0x04,0xF4,0x56,0x80,0x01,
-0x46,0xF6,0xDF,0xE4,0x80,0x0B,0x01,0x02,
-0x04,0x08,0x10,0x20,0x40,0x80,0x90,0x07,
-0xE7,0xE4,0x7E,0x01,0x93,0x60,0xBC,0xA3,
-0xFF,0x54,0x3F,0x30,0xE5,0x09,0x54,0x1F,
-0xFE,0xE4,0x93,0xA3,0x60,0x01,0x0E,0xCF,
-0x54,0xC0,0x25,0xE0,0x60,0xA8,0x40,0xB8,
-0xE4,0x93,0xA3,0xFA,0xE4,0x93,0xA3,0xF8,
-0xE4,0x93,0xA3,0xC8,0xC5,0x82,0xC8,0xCA,
-0xC5,0x83,0xCA,0xF0,0xA3,0xC8,0xC5,0x82,
-0xC8,0xCA,0xC5,0x83,0xCA,0xDF,0xE9,0xDE,
-0xE7,0x80,0xBE,0x7D,0x40,0x7C,0x17,0x7F,
-0x11,0x7E,0x1D,0x12,0x07,0xAB,0x7F,0x41,
-0x7E,0x1D,0x12,0x07,0x66,0xEF,0x44,0x20,
-0x44,0x80,0xFD,0xAC,0x06,0x7F,0x41,0x7E,
-0x1D,0x12,0x07,0xAB,0x7D,0xBB,0x7C,0x15,
-0x7F,0xEB,0x7E,0x13,0x12,0x07,0xAB,0x7D,
-0x07,0x7C,0x00,0x7F,0xE7,0x7E,0x13,0x12,
-0x07,0xAB,0x7D,0x40,0x7C,0x11,0x7F,0x00,
-0x7E,0x62,0x12,0x07,0xAB,0x02,0x02,0x2F,
-0x7D,0xC0,0x7C,0x16,0x7F,0x11,0x7E,0x1D,
-0x12,0x07,0xAB,0x7D,0xBB,0x7C,0x15,0x7F,
-0xEB,0x7E,0x13,0x12,0x07,0xAB,0x7D,0x0D,
-0x7C,0x00,0x7F,0xE7,0x7E,0x13,0x12,0x07,
-0xAB,0x7F,0x41,0x7E,0x1D,0x12,0x07,0x66,
-0xEF,0x44,0x20,0x44,0x80,0xFD,0xAC,0x06,
-0x7F,0x41,0x7E,0x1D,0x12,0x07,0xAB,0x7D,
-0x00,0x7C,0x21,0x7F,0x00,0x7E,0x62,0x12,
-0x07,0xAB,0x02,0x02,0x2F,0x7D,0x40,0x7C,
-0x17,0x7F,0x11,0x7E,0x1D,0x12,0x07,0xAB,
-0x7D,0xBB,0x7C,0x15,0x7F,0xEB,0x7E,0x13,
-0x12,0x07,0xAB,0x7D,0x0C,0x7C,0x00,0x7F,
-0xE7,0x7E,0x13,0x12,0x07,0xAB,0x7F,0x41,
-0x7E,0x1D,0x12,0x07,0x66,0xEF,0x44,0x20,
-0x44,0x80,0xFD,0xAC,0x06,0x7F,0x41,0x7E,
-0x1D,0x12,0x07,0xAB,0x7D,0x40,0x7C,0x11,
-0x7F,0x00,0x7E,0x62,0x12,0x07,0xAB,0x02,
-0x02,0x2F,0x7D,0x04,0x7C,0x00,0x7F,0x01,
-0x7E,0x66,0x12,0x07,0xAB,0x7D,0x80,0x7C,
-0x00,0x7F,0x00,0x7E,0x66,0x12,0x07,0xAB,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0x66,0xEF,
-0x44,0x02,0x44,0x04,0xFD,0xAC,0x06,0x7F,
-0x02,0x7E,0x66,0x12,0x07,0xAB,0x7D,0x04,
-0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xAB,0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x02,0x07,0xAB,0xC0,0xE0,0xC0,0xF0,
-0xC0,0x83,0xC0,0x82,0xC0,0xD0,0x75,0xD0,
-0x00,0xC0,0x00,0x78,0x17,0xE6,0xF5,0x8C,
-0x78,0x18,0xE6,0xF5,0x8A,0x90,0x06,0x31,
-0xE4,0x75,0xF0,0x01,0x12,0x00,0x0E,0x90,
-0x06,0x33,0xE4,0x75,0xF0,0x01,0x12,0x00,
-0x0E,0xD0,0x00,0xD0,0xD0,0xD0,0x82,0xD0,
-0x83,0xD0,0xF0,0xD0,0xE0,0x32,0xC2,0xAF,
-0xAD,0x07,0xAC,0x06,0x8C,0xA2,0x8D,0xA3,
-0x75,0xA0,0x01,0x00,0x00,0x00,0x00,0x00,
-0x00,0x00,0x00,0x00,0x00,0x00,0xAE,0xA1,
-0xBE,0x00,0xF0,0xAE,0xA6,0xAF,0xA7,0xD2,
-0xAF,0x22,0x7D,0x20,0x7C,0x0F,0x7F,0x02,
-0x7E,0x66,0x12,0x07,0xAB,0x7D,0x01,0x7C,
-0x00,0x7F,0x01,0x7E,0x66,0x12,0x07,0xAB,
-0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,
-0x02,0x07,0xAB,0xC2,0xAF,0xAB,0x07,0xAA,
-0x06,0x8A,0xA2,0x8B,0xA3,0x8C,0xA4,0x8D,
-0xA5,0x75,0xA0,0x03,0x00,0x00,0x00,0xAA,
-0xA1,0xBA,0x00,0xF8,0xD2,0xAF,0x22,0x7F,
-0x0C,0x7E,0x13,0x12,0x07,0x66,0xEF,0x44,
-0x50,0xFD,0xAC,0x06,0x7F,0x0C,0x7E,0x13,
-0x02,0x07,0xAB,0x12,0x07,0xC7,0x12,0x07,
-0xF2,0x12,0x04,0x2B,0x02,0x00,0x03,0x42,
-0x06,0x33,0x00,0x00,0x42,0x06,0x31,0x00,
-0x00,0x00,0xE4,0xF5,0x8E,0x22,};
-
-#define FIBER2_1G_INIT_SIZE 2032
-rtk_uint8 Fiber2_1G[FIBER2_1G_INIT_SIZE] = {
-0x02,0x05,0x89,0xE4,0xF5,0xA8,0xD2,0xAF,
-0x22,0x00,0x00,0x02,0x07,0x26,0xC5,0xF0,
-0xF8,0xA3,0xE0,0x28,0xF0,0xC5,0xF0,0xF8,
-0xE5,0x82,0x15,0x82,0x70,0x02,0x15,0x83,
-0xE0,0x38,0xF0,0x22,0x75,0xF0,0x08,0x75,
-0x82,0x00,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xCD,0x33,0xCD,0xCC,0x33,0xCC,0xC5,0x82,
-0x33,0xC5,0x82,0x9B,0xED,0x9A,0xEC,0x99,
-0xE5,0x82,0x98,0x40,0x0C,0xF5,0x82,0xEE,
-0x9B,0xFE,0xED,0x9A,0xFD,0xEC,0x99,0xFC,
-0x0F,0xD5,0xF0,0xD6,0xE4,0xCE,0xFB,0xE4,
-0xCD,0xFA,0xE4,0xCC,0xF9,0xA8,0x82,0x22,
-0xB8,0x00,0xC1,0xB9,0x00,0x59,0xBA,0x00,
-0x2D,0xEC,0x8B,0xF0,0x84,0xCF,0xCE,0xCD,
-0xFC,0xE5,0xF0,0xCB,0xF9,0x78,0x18,0xEF,
-0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,0xFD,
-0xEC,0x33,0xFC,0xEB,0x33,0xFB,0x10,0xD7,
-0x03,0x99,0x40,0x04,0xEB,0x99,0xFB,0x0F,
-0xD8,0xE5,0xE4,0xF9,0xFA,0x22,0x78,0x18,
-0xEF,0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,
-0xFD,0xEC,0x33,0xFC,0xC9,0x33,0xC9,0x10,
-0xD7,0x05,0x9B,0xE9,0x9A,0x40,0x07,0xEC,
-0x9B,0xFC,0xE9,0x9A,0xF9,0x0F,0xD8,0xE0,
-0xE4,0xC9,0xFA,0xE4,0xCC,0xFB,0x22,0x75,
-0xF0,0x10,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xED,0x33,0xFD,0xCC,0x33,0xCC,0xC8,0x33,
-0xC8,0x10,0xD7,0x07,0x9B,0xEC,0x9A,0xE8,
-0x99,0x40,0x0A,0xED,0x9B,0xFD,0xEC,0x9A,
-0xFC,0xE8,0x99,0xF8,0x0F,0xD5,0xF0,0xDA,
-0xE4,0xCD,0xFB,0xE4,0xCC,0xFA,0xE4,0xC8,
-0xF9,0x22,0xEB,0x9F,0xF5,0xF0,0xEA,0x9E,
-0x42,0xF0,0xE9,0x9D,0x42,0xF0,0xE8,0x9C,
-0x45,0xF0,0x22,0xE0,0xFC,0xA3,0xE0,0xFD,
-0xA3,0xE0,0xFE,0xA3,0xE0,0xFF,0x22,0xE0,
-0xF8,0xA3,0xE0,0xF9,0xA3,0xE0,0xFA,0xA3,
-0xE0,0xFB,0x22,0xEC,0xF0,0xA3,0xED,0xF0,
-0xA3,0xEE,0xF0,0xA3,0xEF,0xF0,0x22,0x7D,
-0xD7,0x7C,0x04,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x80,0x7C,0x04,0x7F,0x01,
-0x7E,0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,
-0x00,0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0x94,0x7C,0xF9,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0x81,0x7C,0x04,0x7F,
-0x01,0x7E,0x66,0x12,0x07,0xA5,0x7D,0xC0,
-0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0xA2,0x7C,0x31,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0x82,0x7C,0x04,
-0x7F,0x01,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x60,0x7C,0x69,0x7F,0x02,
-0x7E,0x66,0x12,0x07,0xA5,0x7D,0x83,0x7C,
-0x04,0x7F,0x01,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0x28,0x7C,0x97,0x7F,
-0x02,0x7E,0x66,0x12,0x07,0xA5,0x7D,0x84,
-0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0x85,0x7C,0x9D,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x23,0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xA5,0x7D,0x10,0x7C,
-0xD8,0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0x24,0x7C,0x04,0x7F,0x01,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x12,0x07,0xA5,0x7D,0x00,
-0x7C,0x04,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x2F,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x02,0x07,0xA5,0x7D,
-0x03,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0x60,0xEF,0x44,0x40,0xFD,
-0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x03,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0x60,0xEF,0x54,0xBF,0xFD,
-0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0xE4,
-0xFD,0xFC,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0x60,0xEF,0x54,0xFD,0x54,0xFE,
-0xFD,0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xA5,0xE4,0xFD,0xFC,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0xE4,
-0xFD,0xFC,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0x60,0xEF,0x44,0x02,0x44,0x01,
-0xFD,0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xA5,0xE4,0xFD,0xFC,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x02,0x07,0xA5,0xE4,
-0x90,0x06,0x2C,0xF0,0xFD,0x7C,0x01,0x7F,
-0x3F,0x7E,0x1D,0x12,0x07,0xA5,0x7D,0x40,
-0x7C,0x00,0x7F,0x36,0x7E,0x13,0x12,0x07,
-0xA5,0xE4,0xFF,0xFE,0xFD,0x80,0x25,0xE4,
-0x7F,0xFF,0x7E,0xFF,0xFD,0xFC,0x90,0x06,
-0x24,0x12,0x01,0x0F,0xC3,0x12,0x00,0xF2,
-0x50,0x1B,0x90,0x06,0x24,0x12,0x01,0x03,
-0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,0xE4,
-0x3D,0xFD,0xE4,0x3C,0xFC,0x90,0x06,0x24,
-0x12,0x01,0x1B,0x80,0xD2,0xE4,0xF5,0xA8,
-0xD2,0xAF,0x7D,0x1F,0xFC,0x7F,0x49,0x7E,
-0x13,0x12,0x07,0xA5,0x12,0x07,0xD5,0x12,
-0x01,0x27,0x12,0x06,0x9F,0x7D,0x41,0x7C,
-0x00,0x7F,0x36,0x7E,0x13,0x12,0x07,0xA5,
-0xE4,0xFF,0xFE,0xFD,0x80,0x26,0x7F,0xFF,
-0x7E,0xFF,0x7D,0x05,0x7C,0x00,0x90,0x06,
-0x24,0x12,0x01,0x0F,0xC3,0x12,0x00,0xF2,
-0x50,0x1B,0x90,0x06,0x24,0x12,0x01,0x03,
-0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,0xE4,
-0x3D,0xFD,0xE4,0x3C,0xFC,0x90,0x06,0x24,
-0x12,0x01,0x1B,0x80,0xD1,0xC2,0x00,0xC2,
-0x01,0xD2,0xA9,0xD2,0x8C,0x7F,0x01,0x7E,
-0x62,0x12,0x07,0x60,0xEF,0x30,0xE2,0x07,
-0xE4,0x90,0x06,0x2C,0xF0,0x80,0xEE,0x90,
-0x06,0x2C,0xE0,0x70,0x12,0x12,0x04,0xEA,
-0x90,0x06,0x2C,0x74,0x01,0xF0,0xE4,0x90,
-0x06,0x33,0xF0,0xA3,0xF0,0x80,0xD6,0xC3,
-0x90,0x06,0x34,0xE0,0x94,0x62,0x90,0x06,
-0x33,0xE0,0x94,0x00,0x40,0xC7,0xE4,0xF0,
-0xA3,0xF0,0x12,0x04,0xEA,0x90,0x06,0x2C,
-0x74,0x01,0xF0,0x80,0xB8,0x75,0x0F,0x80,
-0x75,0x0E,0x7E,0x75,0x0D,0xAA,0x75,0x0C,
-0x83,0xE4,0xF5,0x10,0x7F,0x36,0x7E,0x13,
-0x12,0x07,0x60,0xEE,0xC4,0xF8,0x54,0xF0,
-0xC8,0xEF,0xC4,0x54,0x0F,0x48,0x54,0x07,
-0xFB,0x7A,0x00,0xEA,0x70,0x4A,0xEB,0x14,
-0x60,0x1C,0x14,0x60,0x27,0x24,0xFE,0x60,
-0x31,0x14,0x60,0x3C,0x24,0x05,0x70,0x38,
-0x75,0x0B,0x00,0x75,0x0A,0xC2,0x75,0x09,
-0xEB,0x75,0x08,0x0B,0x80,0x36,0x75,0x0B,
-0x40,0x75,0x0A,0x59,0x75,0x09,0x73,0x75,
-0x08,0x07,0x80,0x28,0x75,0x0B,0x00,0x75,
-0x0A,0xE1,0x75,0x09,0xF5,0x75,0x08,0x05,
-0x80,0x1A,0x75,0x0B,0xA0,0x75,0x0A,0xAC,
-0x75,0x09,0xB9,0x75,0x08,0x03,0x80,0x0C,
-0x75,0x0B,0x00,0x75,0x0A,0x62,0x75,0x09,
-0x3D,0x75,0x08,0x01,0x75,0x89,0x11,0xE4,
-0x7B,0x60,0x7A,0x09,0xF9,0xF8,0xAF,0x0B,
-0xAE,0x0A,0xAD,0x09,0xAC,0x08,0x12,0x00,
-0x60,0xAA,0x06,0xAB,0x07,0xC3,0xE4,0x9B,
-0xFB,0xE4,0x9A,0xFA,0x78,0x17,0xF6,0xAF,
-0x03,0xEF,0x08,0xF6,0x18,0xE6,0xF5,0x8C,
-0x08,0xE6,0xF5,0x8A,0x74,0x0D,0x2B,0xFB,
-0xE4,0x3A,0x18,0xF6,0xAF,0x03,0xEF,0x08,
-0xF6,0x75,0x88,0x10,0x53,0x8E,0xC7,0xD2,
-0xA9,0x22,0x7F,0x10,0x7E,0x13,0x12,0x07,
-0x60,0x90,0x06,0x2D,0xEE,0xF0,0xA3,0xEF,
-0xF0,0xEE,0x44,0x10,0xFE,0x90,0x06,0x2D,
-0xF0,0xA3,0xEF,0xF0,0x54,0xEF,0xFF,0x90,
-0x06,0x2D,0xEE,0xF0,0xFC,0xA3,0xEF,0xF0,
-0xFD,0x7F,0x10,0x7E,0x13,0x12,0x07,0xA5,
-0xE4,0xFF,0xFE,0x0F,0xBF,0x00,0x01,0x0E,
-0xEF,0x64,0x64,0x4E,0x70,0xF5,0x7D,0x04,
-0x7C,0x00,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x00,0x7C,0x04,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0xE4,
-0xFD,0xFC,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x00,0x7C,0x04,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0x7F,
-0x10,0x7E,0x13,0x12,0x07,0x60,0x90,0x06,
-0x2D,0xEE,0xF0,0xA3,0xEF,0xF0,0xEE,0x54,
-0xEF,0x90,0x06,0x2D,0xF0,0xFC,0xA3,0xEF,
-0xF0,0xFD,0x7F,0x10,0x7E,0x13,0x02,0x07,
-0xA5,0x78,0x7F,0xE4,0xF6,0xD8,0xFD,0x75,
-0x81,0x3C,0x02,0x05,0xD0,0x02,0x03,0x2F,
-0xE4,0x93,0xA3,0xF8,0xE4,0x93,0xA3,0x40,
-0x03,0xF6,0x80,0x01,0xF2,0x08,0xDF,0xF4,
-0x80,0x29,0xE4,0x93,0xA3,0xF8,0x54,0x07,
-0x24,0x0C,0xC8,0xC3,0x33,0xC4,0x54,0x0F,
-0x44,0x20,0xC8,0x83,0x40,0x04,0xF4,0x56,
-0x80,0x01,0x46,0xF6,0xDF,0xE4,0x80,0x0B,
-0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80,
-0x90,0x07,0xE1,0xE4,0x7E,0x01,0x93,0x60,
-0xBC,0xA3,0xFF,0x54,0x3F,0x30,0xE5,0x09,
-0x54,0x1F,0xFE,0xE4,0x93,0xA3,0x60,0x01,
-0x0E,0xCF,0x54,0xC0,0x25,0xE0,0x60,0xA8,
-0x40,0xB8,0xE4,0x93,0xA3,0xFA,0xE4,0x93,
-0xA3,0xF8,0xE4,0x93,0xA3,0xC8,0xC5,0x82,
-0xC8,0xCA,0xC5,0x83,0xCA,0xF0,0xA3,0xC8,
-0xC5,0x82,0xC8,0xCA,0xC5,0x83,0xCA,0xDF,
-0xE9,0xDE,0xE7,0x80,0xBE,0x7D,0x40,0x7C,
-0x17,0x7F,0x11,0x7E,0x1D,0x12,0x07,0xA5,
-0x7F,0x41,0x7E,0x1D,0x12,0x07,0x60,0xEF,
-0x44,0x20,0x44,0x80,0xFD,0xAC,0x06,0x7F,
-0x41,0x7E,0x1D,0x12,0x07,0xA5,0x7D,0xBB,
-0x7C,0x15,0x7F,0xEB,0x7E,0x13,0x12,0x07,
-0xA5,0x7D,0x07,0x7C,0x00,0x7F,0xE7,0x7E,
-0x13,0x12,0x07,0xA5,0x7D,0x40,0x7C,0x11,
-0x7F,0x00,0x7E,0x62,0x12,0x07,0xA5,0x02,
-0x02,0x2F,0x7D,0xC0,0x7C,0x16,0x7F,0x11,
-0x7E,0x1D,0x12,0x07,0xA5,0x7D,0xBB,0x7C,
-0x15,0x7F,0xEB,0x7E,0x13,0x12,0x07,0xA5,
-0x7D,0x0D,0x7C,0x00,0x7F,0xE7,0x7E,0x13,
-0x12,0x07,0xA5,0x7F,0x41,0x7E,0x1D,0x12,
-0x07,0x60,0xEF,0x44,0x20,0x44,0x80,0xFD,
-0xAC,0x06,0x7F,0x41,0x7E,0x1D,0x12,0x07,
-0xA5,0x7D,0x00,0x7C,0x21,0x7F,0x00,0x7E,
-0x62,0x12,0x07,0xA5,0x02,0x02,0x2F,0x7D,
-0x40,0x7C,0x17,0x7F,0x11,0x7E,0x1D,0x12,
-0x07,0xA5,0x7D,0xBB,0x7C,0x15,0x7F,0xEB,
-0x7E,0x13,0x12,0x07,0xA5,0x7D,0x0C,0x7C,
-0x00,0x7F,0xE7,0x7E,0x13,0x12,0x07,0xA5,
-0x7F,0x41,0x7E,0x1D,0x12,0x07,0x60,0xEF,
-0x44,0x20,0x44,0x80,0xFD,0xAC,0x06,0x7F,
-0x41,0x7E,0x1D,0x12,0x07,0xA5,0x7D,0x40,
-0x7C,0x11,0x7F,0x00,0x7E,0x62,0x12,0x07,
-0xA5,0x02,0x02,0x2F,0x7D,0x04,0x7C,0x00,
-0x7F,0x01,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x80,0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,
-0x07,0xA5,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0x60,0xEF,0x44,0x02,0x44,0x04,0xFD,0xAC,
-0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0x04,0x7C,0x00,0x7F,0x01,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x02,0x07,0xA5,0xC0,0xE0,
-0xC0,0xF0,0xC0,0x83,0xC0,0x82,0xC0,0xD0,
-0x75,0xD0,0x00,0xC0,0x00,0x78,0x17,0xE6,
-0xF5,0x8C,0x78,0x18,0xE6,0xF5,0x8A,0x90,
-0x06,0x31,0xE4,0x75,0xF0,0x01,0x12,0x00,
-0x0E,0x90,0x06,0x33,0xE4,0x75,0xF0,0x01,
-0x12,0x00,0x0E,0xD0,0x00,0xD0,0xD0,0xD0,
-0x82,0xD0,0x83,0xD0,0xF0,0xD0,0xE0,0x32,
-0xC2,0xAF,0xAD,0x07,0xAC,0x06,0x8C,0xA2,
-0x8D,0xA3,0x75,0xA0,0x01,0x00,0x00,0x00,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-0xAE,0xA1,0xBE,0x00,0xF0,0xAE,0xA6,0xAF,
-0xA7,0xD2,0xAF,0x22,0x7D,0x20,0x7C,0x0F,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x01,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x02,0x07,0xA5,0xC2,0xAF,0xAB,
-0x07,0xAA,0x06,0x8A,0xA2,0x8B,0xA3,0x8C,
-0xA4,0x8D,0xA5,0x75,0xA0,0x03,0x00,0x00,
-0x00,0xAA,0xA1,0xBA,0x00,0xF8,0xD2,0xAF,
-0x22,0x7F,0x0C,0x7E,0x13,0x12,0x07,0x60,
-0xEF,0x44,0x50,0xFD,0xAC,0x06,0x7F,0x0C,
-0x7E,0x13,0x02,0x07,0xA5,0x12,0x07,0xC1,
-0x12,0x07,0xEC,0x12,0x04,0x25,0x02,0x00,
-0x03,0x42,0x06,0x33,0x00,0x00,0x42,0x06,
-0x31,0x00,0x00,0x00,0xE4,0xF5,0x8E,0x22,};
-
-#define FIBER2_100M_INIT_SIZE 2032
-rtk_uint8 Fiber2_100M[FIBER2_100M_INIT_SIZE] = {
-0x02,0x05,0x89,0xE4,0xF5,0xA8,0xD2,0xAF,
-0x22,0x00,0x00,0x02,0x07,0x26,0xC5,0xF0,
-0xF8,0xA3,0xE0,0x28,0xF0,0xC5,0xF0,0xF8,
-0xE5,0x82,0x15,0x82,0x70,0x02,0x15,0x83,
-0xE0,0x38,0xF0,0x22,0x75,0xF0,0x08,0x75,
-0x82,0x00,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xCD,0x33,0xCD,0xCC,0x33,0xCC,0xC5,0x82,
-0x33,0xC5,0x82,0x9B,0xED,0x9A,0xEC,0x99,
-0xE5,0x82,0x98,0x40,0x0C,0xF5,0x82,0xEE,
-0x9B,0xFE,0xED,0x9A,0xFD,0xEC,0x99,0xFC,
-0x0F,0xD5,0xF0,0xD6,0xE4,0xCE,0xFB,0xE4,
-0xCD,0xFA,0xE4,0xCC,0xF9,0xA8,0x82,0x22,
-0xB8,0x00,0xC1,0xB9,0x00,0x59,0xBA,0x00,
-0x2D,0xEC,0x8B,0xF0,0x84,0xCF,0xCE,0xCD,
-0xFC,0xE5,0xF0,0xCB,0xF9,0x78,0x18,0xEF,
-0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,0xFD,
-0xEC,0x33,0xFC,0xEB,0x33,0xFB,0x10,0xD7,
-0x03,0x99,0x40,0x04,0xEB,0x99,0xFB,0x0F,
-0xD8,0xE5,0xE4,0xF9,0xFA,0x22,0x78,0x18,
-0xEF,0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,
-0xFD,0xEC,0x33,0xFC,0xC9,0x33,0xC9,0x10,
-0xD7,0x05,0x9B,0xE9,0x9A,0x40,0x07,0xEC,
-0x9B,0xFC,0xE9,0x9A,0xF9,0x0F,0xD8,0xE0,
-0xE4,0xC9,0xFA,0xE4,0xCC,0xFB,0x22,0x75,
-0xF0,0x10,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xED,0x33,0xFD,0xCC,0x33,0xCC,0xC8,0x33,
-0xC8,0x10,0xD7,0x07,0x9B,0xEC,0x9A,0xE8,
-0x99,0x40,0x0A,0xED,0x9B,0xFD,0xEC,0x9A,
-0xFC,0xE8,0x99,0xF8,0x0F,0xD5,0xF0,0xDA,
-0xE4,0xCD,0xFB,0xE4,0xCC,0xFA,0xE4,0xC8,
-0xF9,0x22,0xEB,0x9F,0xF5,0xF0,0xEA,0x9E,
-0x42,0xF0,0xE9,0x9D,0x42,0xF0,0xE8,0x9C,
-0x45,0xF0,0x22,0xE0,0xFC,0xA3,0xE0,0xFD,
-0xA3,0xE0,0xFE,0xA3,0xE0,0xFF,0x22,0xE0,
-0xF8,0xA3,0xE0,0xF9,0xA3,0xE0,0xFA,0xA3,
-0xE0,0xFB,0x22,0xEC,0xF0,0xA3,0xED,0xF0,
-0xA3,0xEE,0xF0,0xA3,0xEF,0xF0,0x22,0x7D,
-0xD7,0x7C,0x04,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x80,0x7C,0x04,0x7F,0x01,
-0x7E,0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,
-0x00,0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0x94,0x7C,0xF9,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0x81,0x7C,0x04,0x7F,
-0x01,0x7E,0x66,0x12,0x07,0xA5,0x7D,0xC0,
-0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0xA2,0x7C,0x31,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0x82,0x7C,0x04,
-0x7F,0x01,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x60,0x7C,0x69,0x7F,0x02,
-0x7E,0x66,0x12,0x07,0xA5,0x7D,0x83,0x7C,
-0x04,0x7F,0x01,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0x28,0x7C,0x97,0x7F,
-0x02,0x7E,0x66,0x12,0x07,0xA5,0x7D,0x84,
-0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0xC0,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0x85,0x7C,0x9D,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x23,0x7C,0x04,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xA5,0x7D,0x10,0x7C,
-0xD8,0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0x24,0x7C,0x04,0x7F,0x01,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x12,0x07,0xA5,0x7D,0x00,
-0x7C,0x04,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x2F,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x02,0x07,0xA5,0x7D,
-0x03,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0x60,0xEF,0x44,0x40,0xFD,
-0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x03,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,
-0x66,0x12,0x07,0x60,0xEF,0x54,0xBF,0xFD,
-0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0xE4,
-0xFD,0xFC,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0x60,0xEF,0x54,0xFD,0x54,0xFE,
-0xFD,0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xA5,0xE4,0xFD,0xFC,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0xE4,
-0xFD,0xFC,0x7F,0x01,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x80,0x7C,0x00,0x7F,0x00,0x7E,
-0x66,0x12,0x07,0xA5,0x7F,0x02,0x7E,0x66,
-0x12,0x07,0x60,0xEF,0x44,0x02,0x44,0x01,
-0xFD,0xAC,0x06,0x7F,0x02,0x7E,0x66,0x12,
-0x07,0xA5,0xE4,0xFD,0xFC,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x02,0x07,0xA5,0xE4,
-0x90,0x06,0x2C,0xF0,0xFD,0x7C,0x01,0x7F,
-0x3F,0x7E,0x1D,0x12,0x07,0xA5,0x7D,0x40,
-0x7C,0x00,0x7F,0x36,0x7E,0x13,0x12,0x07,
-0xA5,0xE4,0xFF,0xFE,0xFD,0x80,0x25,0xE4,
-0x7F,0xFF,0x7E,0xFF,0xFD,0xFC,0x90,0x06,
-0x24,0x12,0x01,0x0F,0xC3,0x12,0x00,0xF2,
-0x50,0x1B,0x90,0x06,0x24,0x12,0x01,0x03,
-0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,0xE4,
-0x3D,0xFD,0xE4,0x3C,0xFC,0x90,0x06,0x24,
-0x12,0x01,0x1B,0x80,0xD2,0xE4,0xF5,0xA8,
-0xD2,0xAF,0x7D,0x1F,0xFC,0x7F,0x49,0x7E,
-0x13,0x12,0x07,0xA5,0x12,0x07,0xD5,0x12,
-0x01,0x27,0x12,0x06,0x5A,0x7D,0x41,0x7C,
-0x00,0x7F,0x36,0x7E,0x13,0x12,0x07,0xA5,
-0xE4,0xFF,0xFE,0xFD,0x80,0x26,0x7F,0xFF,
-0x7E,0xFF,0x7D,0x05,0x7C,0x00,0x90,0x06,
-0x24,0x12,0x01,0x0F,0xC3,0x12,0x00,0xF2,
-0x50,0x1B,0x90,0x06,0x24,0x12,0x01,0x03,
-0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,0xE4,
-0x3D,0xFD,0xE4,0x3C,0xFC,0x90,0x06,0x24,
-0x12,0x01,0x1B,0x80,0xD1,0xC2,0x00,0xC2,
-0x01,0xD2,0xA9,0xD2,0x8C,0x7F,0x01,0x7E,
-0x62,0x12,0x07,0x60,0xEF,0x30,0xE2,0x07,
-0xE4,0x90,0x06,0x2C,0xF0,0x80,0xEE,0x90,
-0x06,0x2C,0xE0,0x70,0x12,0x12,0x04,0xEA,
-0x90,0x06,0x2C,0x74,0x01,0xF0,0xE4,0x90,
-0x06,0x33,0xF0,0xA3,0xF0,0x80,0xD6,0xC3,
-0x90,0x06,0x34,0xE0,0x94,0x62,0x90,0x06,
-0x33,0xE0,0x94,0x00,0x40,0xC7,0xE4,0xF0,
-0xA3,0xF0,0x12,0x04,0xEA,0x90,0x06,0x2C,
-0x74,0x01,0xF0,0x80,0xB8,0x75,0x0F,0x80,
-0x75,0x0E,0x7E,0x75,0x0D,0xAA,0x75,0x0C,
-0x83,0xE4,0xF5,0x10,0x7F,0x36,0x7E,0x13,
-0x12,0x07,0x60,0xEE,0xC4,0xF8,0x54,0xF0,
-0xC8,0xEF,0xC4,0x54,0x0F,0x48,0x54,0x07,
-0xFB,0x7A,0x00,0xEA,0x70,0x4A,0xEB,0x14,
-0x60,0x1C,0x14,0x60,0x27,0x24,0xFE,0x60,
-0x31,0x14,0x60,0x3C,0x24,0x05,0x70,0x38,
-0x75,0x0B,0x00,0x75,0x0A,0xC2,0x75,0x09,
-0xEB,0x75,0x08,0x0B,0x80,0x36,0x75,0x0B,
-0x40,0x75,0x0A,0x59,0x75,0x09,0x73,0x75,
-0x08,0x07,0x80,0x28,0x75,0x0B,0x00,0x75,
-0x0A,0xE1,0x75,0x09,0xF5,0x75,0x08,0x05,
-0x80,0x1A,0x75,0x0B,0xA0,0x75,0x0A,0xAC,
-0x75,0x09,0xB9,0x75,0x08,0x03,0x80,0x0C,
-0x75,0x0B,0x00,0x75,0x0A,0x62,0x75,0x09,
-0x3D,0x75,0x08,0x01,0x75,0x89,0x11,0xE4,
-0x7B,0x60,0x7A,0x09,0xF9,0xF8,0xAF,0x0B,
-0xAE,0x0A,0xAD,0x09,0xAC,0x08,0x12,0x00,
-0x60,0xAA,0x06,0xAB,0x07,0xC3,0xE4,0x9B,
-0xFB,0xE4,0x9A,0xFA,0x78,0x17,0xF6,0xAF,
-0x03,0xEF,0x08,0xF6,0x18,0xE6,0xF5,0x8C,
-0x08,0xE6,0xF5,0x8A,0x74,0x0D,0x2B,0xFB,
-0xE4,0x3A,0x18,0xF6,0xAF,0x03,0xEF,0x08,
-0xF6,0x75,0x88,0x10,0x53,0x8E,0xC7,0xD2,
-0xA9,0x22,0x7F,0x10,0x7E,0x13,0x12,0x07,
-0x60,0x90,0x06,0x2D,0xEE,0xF0,0xA3,0xEF,
-0xF0,0xEE,0x44,0x10,0xFE,0x90,0x06,0x2D,
-0xF0,0xA3,0xEF,0xF0,0x54,0xEF,0xFF,0x90,
-0x06,0x2D,0xEE,0xF0,0xFC,0xA3,0xEF,0xF0,
-0xFD,0x7F,0x10,0x7E,0x13,0x12,0x07,0xA5,
-0xE4,0xFF,0xFE,0x0F,0xBF,0x00,0x01,0x0E,
-0xEF,0x64,0x64,0x4E,0x70,0xF5,0x7D,0x04,
-0x7C,0x00,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x00,0x7C,0x04,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0xE4,
-0xFD,0xFC,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0xA5,0x7D,0x00,0x7C,0x04,0x7F,0x01,0x7E,
-0x66,0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x07,0xA5,0x7F,
-0x10,0x7E,0x13,0x12,0x07,0x60,0x90,0x06,
-0x2D,0xEE,0xF0,0xA3,0xEF,0xF0,0xEE,0x54,
-0xEF,0x90,0x06,0x2D,0xF0,0xFC,0xA3,0xEF,
-0xF0,0xFD,0x7F,0x10,0x7E,0x13,0x02,0x07,
-0xA5,0x78,0x7F,0xE4,0xF6,0xD8,0xFD,0x75,
-0x81,0x3C,0x02,0x05,0xD0,0x02,0x03,0x2F,
-0xE4,0x93,0xA3,0xF8,0xE4,0x93,0xA3,0x40,
-0x03,0xF6,0x80,0x01,0xF2,0x08,0xDF,0xF4,
-0x80,0x29,0xE4,0x93,0xA3,0xF8,0x54,0x07,
-0x24,0x0C,0xC8,0xC3,0x33,0xC4,0x54,0x0F,
-0x44,0x20,0xC8,0x83,0x40,0x04,0xF4,0x56,
-0x80,0x01,0x46,0xF6,0xDF,0xE4,0x80,0x0B,
-0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80,
-0x90,0x07,0xE1,0xE4,0x7E,0x01,0x93,0x60,
-0xBC,0xA3,0xFF,0x54,0x3F,0x30,0xE5,0x09,
-0x54,0x1F,0xFE,0xE4,0x93,0xA3,0x60,0x01,
-0x0E,0xCF,0x54,0xC0,0x25,0xE0,0x60,0xA8,
-0x40,0xB8,0xE4,0x93,0xA3,0xFA,0xE4,0x93,
-0xA3,0xF8,0xE4,0x93,0xA3,0xC8,0xC5,0x82,
-0xC8,0xCA,0xC5,0x83,0xCA,0xF0,0xA3,0xC8,
-0xC5,0x82,0xC8,0xCA,0xC5,0x83,0xCA,0xDF,
-0xE9,0xDE,0xE7,0x80,0xBE,0x7D,0x40,0x7C,
-0x17,0x7F,0x11,0x7E,0x1D,0x12,0x07,0xA5,
-0x7F,0x41,0x7E,0x1D,0x12,0x07,0x60,0xEF,
-0x44,0x20,0x44,0x80,0xFD,0xAC,0x06,0x7F,
-0x41,0x7E,0x1D,0x12,0x07,0xA5,0x7D,0xBB,
-0x7C,0x15,0x7F,0xEB,0x7E,0x13,0x12,0x07,
-0xA5,0x7D,0x07,0x7C,0x00,0x7F,0xE7,0x7E,
-0x13,0x12,0x07,0xA5,0x7D,0x40,0x7C,0x11,
-0x7F,0x00,0x7E,0x62,0x12,0x07,0xA5,0x02,
-0x02,0x2F,0x7D,0xC0,0x7C,0x16,0x7F,0x11,
-0x7E,0x1D,0x12,0x07,0xA5,0x7D,0xBB,0x7C,
-0x15,0x7F,0xEB,0x7E,0x13,0x12,0x07,0xA5,
-0x7D,0x0D,0x7C,0x00,0x7F,0xE7,0x7E,0x13,
-0x12,0x07,0xA5,0x7F,0x41,0x7E,0x1D,0x12,
-0x07,0x60,0xEF,0x44,0x20,0x44,0x80,0xFD,
-0xAC,0x06,0x7F,0x41,0x7E,0x1D,0x12,0x07,
-0xA5,0x7D,0x00,0x7C,0x21,0x7F,0x00,0x7E,
-0x62,0x12,0x07,0xA5,0x02,0x02,0x2F,0x7D,
-0x40,0x7C,0x17,0x7F,0x11,0x7E,0x1D,0x12,
-0x07,0xA5,0x7D,0xBB,0x7C,0x15,0x7F,0xEB,
-0x7E,0x13,0x12,0x07,0xA5,0x7D,0x0C,0x7C,
-0x00,0x7F,0xE7,0x7E,0x13,0x12,0x07,0xA5,
-0x7F,0x41,0x7E,0x1D,0x12,0x07,0x60,0xEF,
-0x44,0x20,0x44,0x80,0xFD,0xAC,0x06,0x7F,
-0x41,0x7E,0x1D,0x12,0x07,0xA5,0x7D,0x40,
-0x7C,0x11,0x7F,0x00,0x7E,0x62,0x12,0x07,
-0xA5,0x02,0x02,0x2F,0x7D,0x04,0x7C,0x00,
-0x7F,0x01,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x80,0x7C,0x00,0x7F,0x00,0x7E,0x66,0x12,
-0x07,0xA5,0x7F,0x02,0x7E,0x66,0x12,0x07,
-0x60,0xEF,0x44,0x02,0x44,0x04,0xFD,0xAC,
-0x06,0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,
-0x7D,0x04,0x7C,0x00,0x7F,0x01,0x7E,0x66,
-0x12,0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x02,0x07,0xA5,0xC0,0xE0,
-0xC0,0xF0,0xC0,0x83,0xC0,0x82,0xC0,0xD0,
-0x75,0xD0,0x00,0xC0,0x00,0x78,0x17,0xE6,
-0xF5,0x8C,0x78,0x18,0xE6,0xF5,0x8A,0x90,
-0x06,0x31,0xE4,0x75,0xF0,0x01,0x12,0x00,
-0x0E,0x90,0x06,0x33,0xE4,0x75,0xF0,0x01,
-0x12,0x00,0x0E,0xD0,0x00,0xD0,0xD0,0xD0,
-0x82,0xD0,0x83,0xD0,0xF0,0xD0,0xE0,0x32,
-0xC2,0xAF,0xAD,0x07,0xAC,0x06,0x8C,0xA2,
-0x8D,0xA3,0x75,0xA0,0x01,0x00,0x00,0x00,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
-0xAE,0xA1,0xBE,0x00,0xF0,0xAE,0xA6,0xAF,
-0xA7,0xD2,0xAF,0x22,0x7D,0x20,0x7C,0x0F,
-0x7F,0x02,0x7E,0x66,0x12,0x07,0xA5,0x7D,
-0x01,0x7C,0x00,0x7F,0x01,0x7E,0x66,0x12,
-0x07,0xA5,0x7D,0xC0,0x7C,0x00,0x7F,0x00,
-0x7E,0x66,0x02,0x07,0xA5,0xC2,0xAF,0xAB,
-0x07,0xAA,0x06,0x8A,0xA2,0x8B,0xA3,0x8C,
-0xA4,0x8D,0xA5,0x75,0xA0,0x03,0x00,0x00,
-0x00,0xAA,0xA1,0xBA,0x00,0xF8,0xD2,0xAF,
-0x22,0x7F,0x0C,0x7E,0x13,0x12,0x07,0x60,
-0xEF,0x44,0x50,0xFD,0xAC,0x06,0x7F,0x0C,
-0x7E,0x13,0x02,0x07,0xA5,0x12,0x07,0xC1,
-0x12,0x07,0xEC,0x12,0x04,0x25,0x02,0x00,
-0x03,0x42,0x06,0x33,0x00,0x00,0x42,0x06,
-0x31,0x00,0x00,0x00,0xE4,0xF5,0x8E,0x22,};
-
-
-#define SGMII_INIT_SIZE 1183
-rtk_uint8 Sgmii_Init[SGMII_INIT_SIZE] = {
-0x02,0x03,0x81,0xE4,0xF5,0xA8,0xD2,0xAF,
-0x22,0x00,0x00,0x02,0x04,0x0D,0xC5,0xF0,
-0xF8,0xA3,0xE0,0x28,0xF0,0xC5,0xF0,0xF8,
-0xE5,0x82,0x15,0x82,0x70,0x02,0x15,0x83,
-0xE0,0x38,0xF0,0x22,0x75,0xF0,0x08,0x75,
-0x82,0x00,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xCD,0x33,0xCD,0xCC,0x33,0xCC,0xC5,0x82,
-0x33,0xC5,0x82,0x9B,0xED,0x9A,0xEC,0x99,
-0xE5,0x82,0x98,0x40,0x0C,0xF5,0x82,0xEE,
-0x9B,0xFE,0xED,0x9A,0xFD,0xEC,0x99,0xFC,
-0x0F,0xD5,0xF0,0xD6,0xE4,0xCE,0xFB,0xE4,
-0xCD,0xFA,0xE4,0xCC,0xF9,0xA8,0x82,0x22,
-0xB8,0x00,0xC1,0xB9,0x00,0x59,0xBA,0x00,
-0x2D,0xEC,0x8B,0xF0,0x84,0xCF,0xCE,0xCD,
-0xFC,0xE5,0xF0,0xCB,0xF9,0x78,0x18,0xEF,
-0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,0xFD,
-0xEC,0x33,0xFC,0xEB,0x33,0xFB,0x10,0xD7,
-0x03,0x99,0x40,0x04,0xEB,0x99,0xFB,0x0F,
-0xD8,0xE5,0xE4,0xF9,0xFA,0x22,0x78,0x18,
-0xEF,0x2F,0xFF,0xEE,0x33,0xFE,0xED,0x33,
-0xFD,0xEC,0x33,0xFC,0xC9,0x33,0xC9,0x10,
-0xD7,0x05,0x9B,0xE9,0x9A,0x40,0x07,0xEC,
-0x9B,0xFC,0xE9,0x9A,0xF9,0x0F,0xD8,0xE0,
-0xE4,0xC9,0xFA,0xE4,0xCC,0xFB,0x22,0x75,
-0xF0,0x10,0xEF,0x2F,0xFF,0xEE,0x33,0xFE,
-0xED,0x33,0xFD,0xCC,0x33,0xCC,0xC8,0x33,
-0xC8,0x10,0xD7,0x07,0x9B,0xEC,0x9A,0xE8,
-0x99,0x40,0x0A,0xED,0x9B,0xFD,0xEC,0x9A,
-0xFC,0xE8,0x99,0xF8,0x0F,0xD5,0xF0,0xDA,
-0xE4,0xCD,0xFB,0xE4,0xCC,0xFA,0xE4,0xC8,
-0xF9,0x22,0xEB,0x9F,0xF5,0xF0,0xEA,0x9E,
-0x42,0xF0,0xE9,0x9D,0x42,0xF0,0xE8,0x9C,
-0x45,0xF0,0x22,0xE0,0xFC,0xA3,0xE0,0xFD,
-0xA3,0xE0,0xFE,0xA3,0xE0,0xFF,0x22,0xE0,
-0xF8,0xA3,0xE0,0xF9,0xA3,0xE0,0xFA,0xA3,
-0xE0,0xFB,0x22,0xEC,0xF0,0xA3,0xED,0xF0,
-0xA3,0xEE,0xF0,0xA3,0xEF,0xF0,0x22,0xE4,
-0x90,0x06,0x2C,0xF0,0xFD,0x7C,0x01,0x7F,
-0x3F,0x7E,0x1D,0x12,0x04,0x6B,0x7D,0x40,
-0x7C,0x00,0x7F,0x36,0x7E,0x13,0x12,0x04,
-0x6B,0xE4,0xFF,0xFE,0xFD,0x80,0x25,0xE4,
-0x7F,0xFF,0x7E,0xFF,0xFD,0xFC,0x90,0x06,
-0x24,0x12,0x01,0x0F,0xC3,0x12,0x00,0xF2,
-0x50,0x1B,0x90,0x06,0x24,0x12,0x01,0x03,
-0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,0xE4,
-0x3D,0xFD,0xE4,0x3C,0xFC,0x90,0x06,0x24,
-0x12,0x01,0x1B,0x80,0xD2,0xE4,0xF5,0xA8,
-0xD2,0xAF,0x7D,0x1F,0xFC,0x7F,0x49,0x7E,
-0x13,0x12,0x04,0x6B,0x12,0x04,0x92,0x7D,
-0x41,0x7C,0x00,0x7F,0x36,0x7E,0x13,0x12,
-0x04,0x6B,0xE4,0xFF,0xFE,0xFD,0x80,0x25,
-0xE4,0x7F,0x20,0x7E,0x4E,0xFD,0xFC,0x90,
-0x06,0x24,0x12,0x01,0x0F,0xC3,0x12,0x00,
-0xF2,0x50,0x1B,0x90,0x06,0x24,0x12,0x01,
-0x03,0xEF,0x24,0x01,0xFF,0xE4,0x3E,0xFE,
-0xE4,0x3D,0xFD,0xE4,0x3C,0xFC,0x90,0x06,
-0x24,0x12,0x01,0x1B,0x80,0xD2,0xC2,0x00,
-0xC2,0x01,0xD2,0xA9,0xD2,0x8C,0x7F,0x01,
-0x7E,0x62,0x12,0x04,0x47,0xEF,0x30,0xE2,
-0x07,0xE4,0x90,0x06,0x2C,0xF0,0x80,0xEE,
-0x90,0x06,0x2C,0xE0,0x70,0x12,0x12,0x02,
-0xDB,0x90,0x06,0x2C,0x74,0x01,0xF0,0xE4,
-0x90,0x06,0x2F,0xF0,0xA3,0xF0,0x80,0xD6,
-0xC3,0x90,0x06,0x30,0xE0,0x94,0x62,0x90,
-0x06,0x2F,0xE0,0x94,0x00,0x40,0xC7,0xE4,
-0xF0,0xA3,0xF0,0x12,0x02,0xDB,0x90,0x06,
-0x2C,0x74,0x01,0xF0,0x80,0xB8,0x75,0x0F,
-0x80,0x75,0x0E,0x7E,0x75,0x0D,0xAA,0x75,
-0x0C,0x83,0xE4,0xF5,0x10,0x7F,0x36,0x7E,
-0x13,0x12,0x04,0x47,0xEE,0xC4,0xF8,0x54,
-0xF0,0xC8,0xEF,0xC4,0x54,0x0F,0x48,0x54,
-0x07,0xFB,0x7A,0x00,0xEA,0x70,0x4A,0xEB,
-0x14,0x60,0x1C,0x14,0x60,0x27,0x24,0xFE,
-0x60,0x31,0x14,0x60,0x3C,0x24,0x05,0x70,
-0x38,0x75,0x0B,0x00,0x75,0x0A,0xC2,0x75,
-0x09,0xEB,0x75,0x08,0x0B,0x80,0x36,0x75,
-0x0B,0x40,0x75,0x0A,0x59,0x75,0x09,0x73,
-0x75,0x08,0x07,0x80,0x28,0x75,0x0B,0x00,
-0x75,0x0A,0xE1,0x75,0x09,0xF5,0x75,0x08,
-0x05,0x80,0x1A,0x75,0x0B,0xA0,0x75,0x0A,
-0xAC,0x75,0x09,0xB9,0x75,0x08,0x03,0x80,
-0x0C,0x75,0x0B,0x00,0x75,0x0A,0x62,0x75,
-0x09,0x3D,0x75,0x08,0x01,0x75,0x89,0x11,
-0xE4,0x7B,0x60,0x7A,0x09,0xF9,0xF8,0xAF,
-0x0B,0xAE,0x0A,0xAD,0x09,0xAC,0x08,0x12,
-0x00,0x60,0xAA,0x06,0xAB,0x07,0xC3,0xE4,
-0x9B,0xFB,0xE4,0x9A,0xFA,0x78,0x17,0xF6,
-0xAF,0x03,0xEF,0x08,0xF6,0x18,0xE6,0xF5,
-0x8C,0x08,0xE6,0xF5,0x8A,0x74,0x0D,0x2B,
-0xFB,0xE4,0x3A,0x18,0xF6,0xAF,0x03,0xEF,
-0x08,0xF6,0x75,0x88,0x10,0x53,0x8E,0xC7,
-0xD2,0xA9,0x22,0x7D,0x02,0x7C,0x00,0x7F,
-0x4A,0x7E,0x13,0x12,0x04,0x6B,0x7D,0x46,
-0x7C,0x71,0x7F,0x02,0x7E,0x66,0x12,0x04,
-0x6B,0x7D,0x03,0x7C,0x00,0x7F,0x01,0x7E,
-0x66,0x12,0x04,0x6B,0x7D,0xC0,0x7C,0x00,
-0x7F,0x00,0x7E,0x66,0x12,0x04,0x6B,0xE4,
-0xFF,0xFE,0x0F,0xBF,0x00,0x01,0x0E,0xEF,
-0x64,0x64,0x4E,0x70,0xF5,0x7D,0x04,0x7C,
-0x00,0x7F,0x02,0x7E,0x66,0x12,0x04,0x6B,
-0x7D,0x00,0x7C,0x04,0x7F,0x01,0x7E,0x66,
-0x12,0x04,0x6B,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x12,0x04,0x6B,0xE4,0xFD,
-0xFC,0x7F,0x02,0x7E,0x66,0x12,0x04,0x6B,
-0x7D,0x00,0x7C,0x04,0x7F,0x01,0x7E,0x66,
-0x12,0x04,0x6B,0x7D,0xC0,0x7C,0x00,0x7F,
-0x00,0x7E,0x66,0x12,0x04,0x6B,0xE4,0xFD,
-0xFC,0x7F,0x4A,0x7E,0x13,0x12,0x04,0x6B,
-0x7D,0x06,0x7C,0x71,0x7F,0x02,0x7E,0x66,
-0x12,0x04,0x6B,0x7D,0x03,0x7C,0x00,0x7F,
-0x01,0x7E,0x66,0x12,0x04,0x6B,0x7D,0xC0,
-0x7C,0x00,0x7F,0x00,0x7E,0x66,0x02,0x04,
-0x6B,0x78,0x7F,0xE4,0xF6,0xD8,0xFD,0x75,
-0x81,0x3C,0x02,0x03,0xC8,0x02,0x01,0x27,
-0xE4,0x93,0xA3,0xF8,0xE4,0x93,0xA3,0x40,
-0x03,0xF6,0x80,0x01,0xF2,0x08,0xDF,0xF4,
-0x80,0x29,0xE4,0x93,0xA3,0xF8,0x54,0x07,
-0x24,0x0C,0xC8,0xC3,0x33,0xC4,0x54,0x0F,
-0x44,0x20,0xC8,0x83,0x40,0x04,0xF4,0x56,
-0x80,0x01,0x46,0xF6,0xDF,0xE4,0x80,0x0B,
-0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80,
-0x90,0x04,0x87,0xE4,0x7E,0x01,0x93,0x60,
-0xBC,0xA3,0xFF,0x54,0x3F,0x30,0xE5,0x09,
-0x54,0x1F,0xFE,0xE4,0x93,0xA3,0x60,0x01,
-0x0E,0xCF,0x54,0xC0,0x25,0xE0,0x60,0xA8,
-0x40,0xB8,0xE4,0x93,0xA3,0xFA,0xE4,0x93,
-0xA3,0xF8,0xE4,0x93,0xA3,0xC8,0xC5,0x82,
-0xC8,0xCA,0xC5,0x83,0xCA,0xF0,0xA3,0xC8,
-0xC5,0x82,0xC8,0xCA,0xC5,0x83,0xCA,0xDF,
-0xE9,0xDE,0xE7,0x80,0xBE,0xC0,0xE0,0xC0,
-0xF0,0xC0,0x83,0xC0,0x82,0xC0,0xD0,0x75,
-0xD0,0x00,0xC0,0x00,0x78,0x17,0xE6,0xF5,
-0x8C,0x78,0x18,0xE6,0xF5,0x8A,0x90,0x06,
-0x2D,0xE4,0x75,0xF0,0x01,0x12,0x00,0x0E,
-0x90,0x06,0x2F,0xE4,0x75,0xF0,0x01,0x12,
-0x00,0x0E,0xD0,0x00,0xD0,0xD0,0xD0,0x82,
-0xD0,0x83,0xD0,0xF0,0xD0,0xE0,0x32,0xC2,
-0xAF,0xAD,0x07,0xAC,0x06,0x8C,0xA2,0x8D,
-0xA3,0x75,0xA0,0x01,0x00,0x00,0x00,0x00,
-0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xAE,
-0xA1,0xBE,0x00,0xF0,0xAE,0xA6,0xAF,0xA7,
-0xD2,0xAF,0x22,0xC2,0xAF,0xAB,0x07,0xAA,
-0x06,0x8A,0xA2,0x8B,0xA3,0x8C,0xA4,0x8D,
-0xA5,0x75,0xA0,0x03,0x00,0x00,0x00,0xAA,
-0xA1,0xBA,0x00,0xF8,0xD2,0xAF,0x22,0x42,
-0x06,0x2F,0x00,0x00,0x42,0x06,0x2D,0x00,
-0x00,0x00,0x12,0x04,0x9B,0x12,0x02,0x16,
-0x02,0x00,0x03,0xE4,0xF5,0x8E,0x22,};
-
-
-/* Function Name:
- *      rtl8367c_setAsicPortUnknownDaBehavior
- * Description:
- *      Set UNDA behavior
- * Input:
- *      port        - port ID
- *      behavior    - 0: flooding to unknwon DA portmask; 1: drop; 2:trap; 3: flooding
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NOT_ALLOWED  - Invalid behavior
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortUnknownDaBehavior(rtk_uint32 port, rtk_uint32 behavior)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(behavior >= L2_UNDA_BEHAVE_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    if(port < 8)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_UNKNOWN_UNICAST_DA_PORT_BEHAVE, RTL8367C_Port0_ACTION_MASK << (port * 2), behavior);
-    else
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_UNKNOWN_UNICAST_DA_PORT_BEHAVE_EXT, RTL8367C_PORT8_ACTION_MASK << ((port-8) * 2), behavior);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortUnknownDaBehavior
- * Description:
- *      Get UNDA behavior
- * Input:
- *      port        - port ID
- * Output:
- *      pBehavior   - 0: flooding to unknwon DA portmask; 1: drop; 2:trap; 3: flooding
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortUnknownDaBehavior(rtk_uint32 port, rtk_uint32 *pBehavior)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_UNKNOWN_UNICAST_DA_PORT_BEHAVE, RTL8367C_Port0_ACTION_MASK << (port * 2), pBehavior);
-    else
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_UNKNOWN_UNICAST_DA_PORT_BEHAVE_EXT, RTL8367C_PORT8_ACTION_MASK << ((port-8) * 2), pBehavior);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortUnknownSaBehavior
- * Description:
- *      Set UNSA behavior
- * Input:
- *      behavior    - 0: flooding; 1: drop; 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NOT_ALLOWED  - Invalid behavior
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortUnknownSaBehavior(rtk_uint32 behavior)
-{
-    if(behavior >= L2_BEHAVE_SA_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_PORT_SECURIT_CTRL_REG, RTL8367C_UNKNOWN_SA_BEHAVE_MASK, behavior);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortUnknownSaBehavior
- * Description:
- *      Get UNSA behavior
- * Input:
- *      pBehavior   - 0: flooding; 1: drop; 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortUnknownSaBehavior(rtk_uint32 *pBehavior)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_PORT_SECURIT_CTRL_REG, RTL8367C_UNKNOWN_SA_BEHAVE_MASK, pBehavior);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortUnmatchedSaBehavior
- * Description:
- *      Set Unmatched SA behavior
- * Input:
- *      behavior    - 0: flooding; 1: drop; 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NOT_ALLOWED  - Invalid behavior
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortUnmatchedSaBehavior(rtk_uint32 behavior)
-{
-    if(behavior >= L2_BEHAVE_SA_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_PORT_SECURIT_CTRL_REG, RTL8367C_UNMATCHED_SA_BEHAVE_MASK, behavior);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortUnmatchedSaBehavior
- * Description:
- *      Get Unmatched SA behavior
- * Input:
- *      pBehavior   - 0: flooding; 1: drop; 2:trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortUnmatchedSaBehavior(rtk_uint32 *pBehavior)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_PORT_SECURIT_CTRL_REG, RTL8367C_UNMATCHED_SA_BEHAVE_MASK, pBehavior);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortUnmatchedSaMoving
- * Description:
- *      Set Unmatched SA moving state
- * Input:
- *      port        - Port ID
- *      enabled     - 0: can't move to new port; 1: can move to new port
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Error Port ID
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortUnmatchedSaMoving(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_L2_SA_MOVING_FORBID, port, (enabled == 1) ? 0 : 1);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPortUnmatchedSaMoving
- * Description:
- *      Get Unmatched SA moving state
- * Input:
- *      port        - Port ID
- * Output:
- *      pEnabled    - 0: can't move to new port; 1: can move to new port
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Error Port ID
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortUnmatchedSaMoving(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    rtk_uint32 data;
-    ret_t retVal;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_L2_SA_MOVING_FORBID, port, &data)) != RT_ERR_OK)
-        return retVal;
-
-    *pEnabled = (data == 1) ? 0 : 1;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortUnknownDaFloodingPortmask
- * Description:
- *      Set UNDA flooding portmask
- * Input:
- *      portmask    - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortUnknownDaFloodingPortmask(rtk_uint32 portmask)
-{
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicReg(RTL8367C_UNUCAST_FLOADING_PMSK_REG, portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortUnknownDaFloodingPortmask
- * Description:
- *      Get UNDA flooding portmask
- * Input:
- *      pPortmask   - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortUnknownDaFloodingPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_UNUCAST_FLOADING_PMSK_REG, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortUnknownMulticastFloodingPortmask
- * Description:
- *      Set UNMC flooding portmask
- * Input:
- *      portmask    - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortUnknownMulticastFloodingPortmask(rtk_uint32 portmask)
-{
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicReg(RTL8367C_UNMCAST_FLOADING_PMSK_REG, portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortUnknownMulticastFloodingPortmask
- * Description:
- *      Get UNMC flooding portmask
- * Input:
- *      pPortmask   - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortUnknownMulticastFloodingPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_UNMCAST_FLOADING_PMSK_REG, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortBcastFloodingPortmask
- * Description:
- *      Set Bcast flooding portmask
- * Input:
- *      portmask    - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortBcastFloodingPortmask(rtk_uint32 portmask)
-{
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicReg(RTL8367C_BCAST_FLOADING_PMSK_REG, portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortBcastFloodingPortmask
- * Description:
- *      Get Bcast flooding portmask
- * Input:
- *      pPortmask   - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortBcastFloodingPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_BCAST_FLOADING_PMSK_REG, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortBlockSpa
- * Description:
- *      Set disabling blocking frame if source port and destination port are the same
- * Input:
- *      port    - Physical port number (0~7)
- *      permit  - 0: block; 1: permit
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortBlockSpa(rtk_uint32 port, rtk_uint32 permit)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_SOURCE_PORT_BLOCK_REG, port, permit);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortBlockSpa
- * Description:
- *      Get disabling blocking frame if source port and destination port are the same
- * Input:
- *      port    - Physical port number (0~7)
- *      pPermit     - 0: block; 1: permit
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortBlockSpa(rtk_uint32 port, rtk_uint32* pPermit)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_SOURCE_PORT_BLOCK_REG, port, pPermit);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortDos
- * Description:
- *      Set DOS function
- * Input:
- *      type    - DOS type
- *      drop    - 0: permit; 1: drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - Invalid payload index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortDos(rtk_uint32 type, rtk_uint32 drop)
-{
-    if(type >= DOS_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_DOS_CFG, RTL8367C_DROP_DAEQSA_OFFSET + type, drop);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortDos
- * Description:
- *      Get DOS function
- * Input:
- *      type    - DOS type
- *      pDrop   - 0: permit; 1: drop
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - Invalid payload index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortDos(rtk_uint32 type, rtk_uint32* pDrop)
-{
-    if(type >= DOS_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_DOS_CFG, RTL8367C_DROP_DAEQSA_OFFSET + type,pDrop);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortForceLink
- * Description:
- *      Set port force linking configuration
- * Input:
- *      port        - Physical port number (0~7)
- *      pPortAbility - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortForceLink(rtk_uint32 port, rtl8367c_port_ability_t *pPortAbility)
-{
-    rtk_uint32 regData = 0;
-
-    /* Invalid input parameter */
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    regData |= pPortAbility->forcemode << 12;
-    regData |= pPortAbility->mstfault << 9;
-    regData |= pPortAbility->mstmode << 8;
-    regData |= pPortAbility->nway << 7;
-    regData |= pPortAbility->txpause << 6;
-    regData |= pPortAbility->rxpause << 5;
-    regData |= pPortAbility->link << 4;
-    regData |= pPortAbility->duplex << 2;
-    regData |= pPortAbility->speed;
-
-    return rtl8367c_setAsicReg(RTL8367C_REG_MAC0_FORCE_SELECT+port, regData);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortForceLink
- * Description:
- *      Get port force linking configuration
- * Input:
- *      port        - Physical port number (0~7)
- *      pPortAbility - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortForceLink(rtk_uint32 port, rtl8367c_port_ability_t *pPortAbility)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Invalid input parameter */
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_MAC0_FORCE_SELECT + port, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pPortAbility->forcemode = (regData >> 12) & 0x0001;
-    pPortAbility->mstfault  = (regData >> 9) & 0x0001;
-    pPortAbility->mstmode   = (regData >> 8) & 0x0001;
-    pPortAbility->nway      = (regData >> 7) & 0x0001;
-    pPortAbility->txpause   = (regData >> 6) & 0x0001;
-    pPortAbility->rxpause   = (regData >> 5) & 0x0001;
-    pPortAbility->link      = (regData >> 4) & 0x0001;
-    pPortAbility->duplex    = (regData >> 2) & 0x0001;
-    pPortAbility->speed     = regData & 0x0003;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicPortStatus
- * Description:
- *      Get port link status
- * Input:
- *      port        - Physical port number (0~7)
- *      pPortAbility - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortStatus(rtk_uint32 port, rtl8367c_port_status_t *pPortStatus)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    /* Invalid input parameter */
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_PORT0_STATUS+port,&regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pPortStatus->lpi1000  = (regData >> 11) & 0x0001;
-    pPortStatus->lpi100   = (regData >> 10) & 0x0001;
-    pPortStatus->mstfault = (regData >> 9) & 0x0001;
-    pPortStatus->mstmode  = (regData >> 8) & 0x0001;
-    pPortStatus->nway     = (regData >> 7) & 0x0001;
-    pPortStatus->txpause  = (regData >> 6) & 0x0001;
-    pPortStatus->rxpause  = (regData >> 5) & 0x0001;
-    pPortStatus->link     = (regData >> 4) & 0x0001;
-    pPortStatus->duplex   = (regData >> 2) & 0x0001;
-    pPortStatus->speed    = regData  & 0x0003;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicPortForceLinkExt
- * Description:
- *      Set external interface force linking configuration
- * Input:
- *      id          - external interface id (0~2)
- *      portAbility - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortForceLinkExt(rtk_uint32 id, rtl8367c_port_ability_t *pPortAbility)
-{
-    rtk_uint32 retVal, regValue, regValue2, type, sgmiibit, hisgmiibit;
-    rtk_uint32 reg_data = 0;
-    rtk_uint32 i = 0;
-
-    /* Invalid input parameter */
-    if(id >= RTL8367C_EXTNO)
-        return RT_ERR_OUT_OF_RANGE;
-
-    reg_data |= pPortAbility->forcemode << 12;
-    reg_data |= pPortAbility->mstfault << 9;
-    reg_data |= pPortAbility->mstmode << 8;
-    reg_data |= pPortAbility->nway << 7;
-    reg_data |= pPortAbility->txpause << 6;
-    reg_data |= pPortAbility->rxpause << 5;
-    reg_data |= pPortAbility->link << 4;
-    reg_data |= pPortAbility->duplex << 2;
-    reg_data |= pPortAbility->speed;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-    /*get chip ID */
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    type = 0;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 1;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 2;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 3;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    if (1 == type)
-    {
-        if(1 == id)
-        {
-            if ((retVal = rtl8367c_getAsicReg(RTL8367C_REG_REG_TO_ECO4, &regValue)) != RT_ERR_OK)
-                return retVal;
-
-            if((regValue & (0x0001 << 5)) && (regValue & (0x0001 << 7)))
-            {
-                return RT_ERR_OK;
-            }
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_FDUP_OFFSET, pPortAbility->duplex)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_SPD_MASK, pPortAbility->speed)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_LINK_OFFSET, pPortAbility->link)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_TXFC_OFFSET, pPortAbility->txpause)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_RXFC_OFFSET, pPortAbility->rxpause)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        if(0 == id || 1 == id)
-            return rtl8367c_setAsicReg(RTL8367C_REG_DIGITAL_INTERFACE0_FORCE + id, reg_data);
-        else
-            return rtl8367c_setAsicReg(RTL8367C_REG_DIGITAL_INTERFACE2_FORCE, reg_data);
-    }
-    else if (2 == type)
-    {
-        if (1 == id)
-        {
-             if((retVal = rtl8367c_setAsicRegBit(0x1311, 2, pPortAbility->duplex)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBits(0x1311, 0x3, pPortAbility->speed)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, pPortAbility->link)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1311, 6, pPortAbility->txpause)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1311, 5, pPortAbility->rxpause)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1311, 12, pPortAbility->forcemode)) != RT_ERR_OK)
-                return retVal;
-
-            if (pPortAbility->link == 1)
-            {
-                if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, 1)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else
-            {
-                if((retVal = rtl8367c_setAsicRegBits(0x1311, 0x3, 2)) != RT_ERR_OK)
-                    return retVal;
-            }
-
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_FDUP_OFFSET, pPortAbility->duplex)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_SPD_MASK, pPortAbility->speed)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_LINK_OFFSET, pPortAbility->link)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_TXFC_OFFSET, pPortAbility->txpause)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_RXFC_OFFSET, pPortAbility->rxpause)) != RT_ERR_OK)
-                return retVal;
-        }
-        else if (2 == id)
-        {
-            if((retVal = rtl8367c_setAsicRegBit(0x13c4, 2, pPortAbility->duplex)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBits(0x13c4, 0x3, pPortAbility->speed)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x13c4, 4, pPortAbility->link)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x13c4, 6, pPortAbility->txpause)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x13c4, 5, pPortAbility->rxpause)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x13c4, 12, pPortAbility->forcemode)) != RT_ERR_OK)
-                return retVal;
-
-            if (pPortAbility->link == 1)
-            {
-                if((retVal = rtl8367c_setAsicRegBit(0x13c4, 4, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if((retVal = rtl8367c_setAsicRegBit(0x13c4, 4, 1)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else
-            {
-                if((retVal = rtl8367c_setAsicRegBits(0x13c4, 0x3, 2)) != RT_ERR_OK)
-                    return retVal;
-            }
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1dc1, RTL8367C_CFG_SGMII_FDUP_OFFSET, pPortAbility->duplex)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBits(0x1dc1, RTL8367C_CFG_SGMII_SPD_MASK, pPortAbility->speed)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1dc1, RTL8367C_CFG_SGMII_LINK_OFFSET, pPortAbility->link)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1dc1, RTL8367C_CFG_SGMII_TXFC_OFFSET, pPortAbility->txpause)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(0x1dc1, RTL8367C_CFG_SGMII_RXFC_OFFSET, pPortAbility->rxpause)) != RT_ERR_OK)
-                return retVal;
-        }
-
-    }
-    else if(3 == type)
-    {
-        if(1 == id)
-        {
-            if((retVal = rtl8367c_getAsicRegBit(0x1d11, 6, &sgmiibit)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_getAsicRegBit(0x1d11, 11, &hisgmiibit)) != RT_ERR_OK)
-                return retVal;
-
-            if ((sgmiibit == 1) || (hisgmiibit == 1))
-            {
-                /*for 1000x/100fx/1000x_100fx, param has to be set to serdes registers*/
-                if((retVal = rtl8367c_getAsicReg(0x1d41, &regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit5: cfg_mac6_fib =1,  bit7: cfg_mac6_fib2=1*/
-                if((regValue & 0xa0) == 0xa0)
-                {
-                     /* new_cfg_sds_mode */
-                    if((retVal = rtl8367c_getAsicRegBits(0x1d95, 0x1f00, &regValue2)) != RT_ERR_OK)
-                        return retVal;
-
-                     /*1000X*/
-                    if(regValue2 == 0x4)
-                    {
-#if 0
-                        /* new_cfg_sds_mode:reset mode */
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                            return retVal;
-#endif
-                        /* Enable new sds mode config */
-                        if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 4*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0x9000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 1,  bit13 set to 0, bit12 nway_en*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFDFFF;
-                        reg_data |= 0x40;
-                        if(pPortAbility->forcemode)
-                            reg_data &= 0xffffefff;
-                        else
-                            reg_data |= 0x1000;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data &= (~0x80);
-
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &= (~0x100);
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /*new_cfg_sds_mode=1000x*/
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x4)) != RT_ERR_OK)
-                            return retVal;
-
-                    }
-                    else if(regValue2 == 0x5)
-                    {
-#if 0
-                        /*100FX*/
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                            return retVal;
-#endif
-                        /*cfg_sds_mode_sel_new=1  */
-                        if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 5*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0xB000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 0,  bit13 set to 1, bit12 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFFFBF;
-                        reg_data |= 0x2000;
-                        reg_data &= 0xffffefff;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data &= (~0x80);
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &= (~0x100);
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-                       /* new_cfg_sds_mode=1000x */
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x5)) != RT_ERR_OK)
-                            return retVal;
-
-                    }
-                    else if(regValue2 == 0x7)
-                    {
-#if 0
-                        /*100FX*/
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                            return retVal;
-#endif
-                        if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 4*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0x9000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 1,  bit13 set to 0, bit12 nway_en*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFDFFF;
-                        reg_data |= 0x40;
-                        if(pPortAbility->forcemode)
-                            reg_data &= 0xffffefff;
-                        else
-                            reg_data |= 0x1000;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data &= (~0x80);
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &=(~0x100);
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 5*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0xB000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 0,  bit13 set to 1, bit12 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFFFBF;
-                        reg_data |= 0x2000;
-                        reg_data &= 0xffffefff;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data &= 0xffffff7f;
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &= 0xfffffeff;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        /*sds_mode:*/
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x7)) != RT_ERR_OK)
-                            return retVal;
-
-                    }
-
-                    /*disable force ability   ---      */
-                    if((retVal = rtl8367c_setAsicRegBit(0x137c, 12, 0)) != RT_ERR_OK)
-                        return retVal;
-                    return RT_ERR_OK;
-
-                }
-
-                /* new_cfg_sds_mode */
-                if((retVal = rtl8367c_getAsicRegBits(0x1d95, 0x1f00, &regValue2)) != RT_ERR_OK)
-                    return retVal;
-                if(regValue2 == 0x2)
-                {
-#if 0
-                    /*SGMII*/
-                    if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                        return retVal;
-#endif
-                    if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                        return retVal;
-
-                    for(i=0;i<0xfff; i++);
-
-                    /* 0 2 0  bit 8-9  nway*/
-                    if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                        return retVal;
-                    reg_data &= 0xfffffcff;
-                    if (pPortAbility->nway)
-                        reg_data &= 0xfffffcff;
-                    else
-                        reg_data |= 0x100;
-                    if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x2)) != RT_ERR_OK)
-                        return retVal;
-
-                    for(i=0;i<0xfff; i++);
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_FDUP_OFFSET, pPortAbility->duplex)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_SPD_MASK, pPortAbility->speed)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_TXFC_OFFSET, pPortAbility->txpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_RXFC_OFFSET, pPortAbility->rxpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_LINK_OFFSET, pPortAbility->link)) != RT_ERR_OK)
-                        return retVal;
-
-                    /*disable force ability   ---      */
-                    if((retVal = rtl8367c_setAsicRegBit(0x137c, 12, 0)) != RT_ERR_OK)
-                        return retVal;
-                    return RT_ERR_OK;
-                }
-                else if(regValue2 == 0x12)
-                {
-#if 0
-                    /*HiSGMII*/
-                    if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                        return retVal;
-#endif
-                    if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                        return retVal;
-
-                    for(i=0;i<0xfff; i++);
-
-                    /* 0 2 0  bit 8-9  nway*/
-                    if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                        return retVal;
-                    reg_data &= 0xfffffcff;
-                    if (pPortAbility->nway)
-                        reg_data &= 0xfffffcff;
-                    else
-                        reg_data |= 0x100;
-                    if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-
-                    if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x12)) != RT_ERR_OK)
-                        return retVal;
-
-                    for(i=0;i<0xfff; i++);
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 0x1)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_FDUP_OFFSET, pPortAbility->duplex)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_SPD_MASK, pPortAbility->speed)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_TXFC_OFFSET, pPortAbility->txpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_RXFC_OFFSET, pPortAbility->rxpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_LINK_OFFSET, pPortAbility->link)) != RT_ERR_OK)
-                        return retVal;
-
-                    /*disable force ability   ---      */
-                    if((retVal = rtl8367c_setAsicRegBit(0x137c, 12, 0)) != RT_ERR_OK)
-                        return retVal;
-                    return RT_ERR_OK;
-
-                }
-            }
-            else
-            {
-                if((retVal = rtl8367c_getAsicRegBits(0x1d3d, 10, &regValue2)) != RT_ERR_OK)
-                    return retVal;
-                if (regValue2 == 0)
-                {
-                    /*ext1_force_ablty*/
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 2, pPortAbility->duplex)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBits(0x1311, 0x3, pPortAbility->speed)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, pPortAbility->link)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 6, pPortAbility->txpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 5, pPortAbility->rxpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    /*force mode for ext1*/
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 12, pPortAbility->forcemode)) != RT_ERR_OK)
-                        return retVal;
-
-                    if (pPortAbility->link == 1)
-                    {
-                        if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, 0)) != RT_ERR_OK)
-                            return retVal;
-
-                        if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, 1)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                    else
-                    {
-                        if((retVal = rtl8367c_setAsicRegBits(0x1311, 0x3, 2)) != RT_ERR_OK)
-                            return retVal;
-                    }
-
-                    /*disable force ability   ---      */
-                    if((retVal = rtl8367c_setAsicRegBit(0x137c, 12, 0)) != RT_ERR_OK)
-                        return retVal;
-                    return RT_ERR_OK;
-                }
-            }
-
-
-        }
-        else if (2 == id)
-        {
-
-            if((retVal = rtl8367c_getAsicRegBit(0x1d95, 0, &sgmiibit)) != RT_ERR_OK)
-                    return retVal;
-            if (sgmiibit == 1)
-            {
-                /*for 1000x/100fx/1000x_100fx, param has to bet set to serdes registers*/
-                if((retVal = rtl8367c_getAsicReg(0x1d95, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                /*cfg_mac7_sel_sgmii=1 & cfg_mac7_fib =1*/
-                if((regValue & 0x3) == 0x3)
-                {
-                    if((retVal = rtl8367c_getAsicRegBits(0x1d95, 0x1f00, &regValue2)) != RT_ERR_OK)
-                        return retVal;
-
-                    if(regValue2 == 0x4)
-                    {
-                        /*1000X*/
-#if 0
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                            return retVal;
-#endif
-                        if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 4*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0x9000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 1,  bit13 set to 0, bit12 nway_en*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFDFFF;
-                        reg_data |= 0x40;
-                        if(pPortAbility->forcemode)
-                            reg_data &= 0xffffefff;
-                        else
-                            reg_data |= 0x1000;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data &= 0xffffff7f;
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &= 0xfffffeff;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x4)) != RT_ERR_OK)
-                            return retVal;
-
-                    }
-                    else if(regValue2 == 0x5)
-                    {
-                        /*100FX*/
-#if 0
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                            return retVal;
-#endif
-                        if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 5*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0xB000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 0,  bit13 set to 1, bit12 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFFFBF;
-                        reg_data |= 0x2000;
-                        reg_data &= 0xffffefff;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data &= 0xffffff7f;
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &= 0xfffffeff;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x5)) != RT_ERR_OK)
-                            return retVal;
-
-                    }
-                    else if(regValue2 == 0x7)
-                    {
-                        /*100FX*/
-#if 0
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                            return retVal;
-#endif
-                        if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 4*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0x9000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 1,  bit13 set to 0, bit12 nway_en*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFDFFF;
-                        reg_data |= 0x40;
-                        if(pPortAbility->forcemode)
-                            reg_data &= 0xffffefff;
-                        else
-                            reg_data |= 0x1000;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data &= 0xffffff7f;
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &= 0xfffffeff;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 0  bit 12  set 1,  bit15~13 = 5*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFF0FFF;
-                        reg_data |= 0xB000;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 0 2  bit 6  set 0,  bit13 set to 1, bit12 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFFFBF;
-                        reg_data |= 0x2000;
-                        reg_data &= 0xffffefff;
-
-                        if((retVal = rtl8367c_setAsicSdsReg(0,0,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* 0 4 2  bit 8  rx pause,  bit7 tx pause*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 2, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        if (pPortAbility->txpause)
-                            reg_data |= 0x80;
-                        else
-                            reg_data  &= 0xffffff7f;
-                        if (pPortAbility->rxpause)
-                            reg_data |= 0x100;
-                        else
-                            reg_data &= 0xfffffeff;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,2, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                         /* 0 4 0  bit 12  set 0*/
-                        if((retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &reg_data)) != RT_ERR_OK)
-                            return retVal;
-                        reg_data &= 0xFFFFEFFF;
-                        if((retVal = rtl8367c_setAsicSdsReg(0,4,0, reg_data)) != RT_ERR_OK)
-                            return retVal;
-
-                        if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x7)) != RT_ERR_OK)
-                            return retVal;
-
-                    }
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x137d, 12, 0)) != RT_ERR_OK)
-                        return retVal;
-                    return RT_ERR_OK;
-
-                }
-                /* new_cfg_sds_mode */
-                if((retVal = rtl8367c_getAsicRegBits(0x1d95, 0x1f00, &regValue2)) != RT_ERR_OK)
-                        return retVal;
-                if(regValue2 == 0x2)
-                {
-                    /*SGMII*/
-#if 0
-                    if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                        return retVal;
-#endif
-                    if((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                        return retVal;
-
-                    for(i=0;i<0xfff; i++);
-
-                    /* 0 2 0  bit 8-9  nway*/
-                    if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                        return retVal;
-                    reg_data &= 0xfffffcff;
-                    if (pPortAbility->nway)
-                        reg_data &= 0xfffffcff;
-                    else
-                        reg_data |= 0x100;
-                    if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x2)) != RT_ERR_OK)
-                        return retVal;
-
-                    for(i=0;i<0xfff; i++);
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_FDUP_OFFSET, pPortAbility->duplex)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_SPD_MASK, pPortAbility->speed)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_TXFC_OFFSET, pPortAbility->txpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_RXFC_OFFSET, pPortAbility->rxpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_LINK_OFFSET, pPortAbility->link)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x137d, 12, 0)) != RT_ERR_OK)
-                        return retVal;
-                    return RT_ERR_OK;
-                }
-            }
-            else
-            {
-
-                /*ext2_force_ablty*/
-                if((retVal = rtl8367c_setAsicRegBit(0x13c4, 2, pPortAbility->duplex)) != RT_ERR_OK)
-                    return retVal;
-
-                if((retVal = rtl8367c_setAsicRegBits(0x13c4, 0x3, pPortAbility->speed)) != RT_ERR_OK)
-                    return retVal;
-
-                if((retVal = rtl8367c_setAsicRegBit(0x13c4, 4, pPortAbility->link)) != RT_ERR_OK)
-                    return retVal;
-
-                if((retVal = rtl8367c_setAsicRegBit(0x13c4, 6, pPortAbility->txpause)) != RT_ERR_OK)
-                    return retVal;
-
-                if((retVal = rtl8367c_setAsicRegBit(0x13c4, 5, pPortAbility->rxpause)) != RT_ERR_OK)
-                    return retVal;
-
-                /*force mode for ext2*/
-                if((retVal = rtl8367c_setAsicRegBit(0x13c4, 12, pPortAbility->forcemode)) != RT_ERR_OK)
-                    return retVal;
-
-                if (pPortAbility->link == 1)
-                {
-                    if((retVal = rtl8367c_setAsicRegBit(0x13c4, 4, 0)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x13c4, 4, 1)) != RT_ERR_OK)
-                        return retVal;
-                }
-                else
-                {
-                    if((retVal = rtl8367c_setAsicRegBits(0x13c4, 0x3, 2)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-
-                if((retVal = rtl8367c_getAsicRegBit(0x1d3d, 10, &reg_data)) != RT_ERR_OK)
-                        return retVal;
-                if(reg_data == 1)
-                {
-                if((retVal = rtl8367c_setAsicRegBit(0x1311, 2, pPortAbility->duplex)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBits(0x1311, 0x3, pPortAbility->speed)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, pPortAbility->link)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 6, pPortAbility->txpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 5, pPortAbility->rxpause)) != RT_ERR_OK)
-                        return retVal;
-
-                    /*force mode for ext1*/
-                    if((retVal = rtl8367c_setAsicRegBit(0x1311, 12, pPortAbility->forcemode)) != RT_ERR_OK)
-                        return retVal;
-
-                    if (pPortAbility->link == 1)
-                    {
-                        if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, 0)) != RT_ERR_OK)
-                            return retVal;
-
-                        if((retVal = rtl8367c_setAsicRegBit(0x1311, 4, 1)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                    else
-                    {
-                        if((retVal = rtl8367c_setAsicRegBits(0x1311, 0x3, 2)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                }
-
-
-            }
-
-            /*disable force ability   ---      */
-            if((retVal = rtl8367c_setAsicRegBit(0x137d, 12, 0)) != RT_ERR_OK)
-                return retVal;
-        }
-#if 0
-        if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_FDUP_OFFSET, pPortAbility->duplex)) != RT_ERR_OK)
-            return retVal;
-
-        if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_SPD_MASK, pPortAbility->speed)) != RT_ERR_OK)
-            return retVal;
-
-        if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_TXFC_OFFSET, pPortAbility->txpause)) != RT_ERR_OK)
-            return retVal;
-
-        if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_RXFC_OFFSET, pPortAbility->rxpause)) != RT_ERR_OK)
-            return retVal;
-
-        if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_LINK_OFFSET, pPortAbility->link)) != RT_ERR_OK)
-            return retVal;
-#endif
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicPortForceLinkExt
- * Description:
- *      Get external interface force linking configuration
- * Input:
- *      id          - external interface id (0~1)
- *      pPortAbility - port ability configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortForceLinkExt(rtk_uint32 id, rtl8367c_port_ability_t *pPortAbility)
-{
-    rtk_uint32  reg_data, regValue, type;
-    rtk_uint32  sgmiiSel;
-    rtk_uint32  hsgmiiSel;
-    ret_t       retVal;
-
-    /* Invalid input parameter */
-    if(id >= RTL8367C_EXTNO)
-        return RT_ERR_OUT_OF_RANGE;
-    /*cfg_magic_id  &  get chip_id*/
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    type = 0;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 1;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 2;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 3;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    if (1 == type)
-    {
-        if(1 == id)
-        {
-            if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_SGMII_OFFSET, &sgmiiSel)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_HSGMII_OFFSET, &hsgmiiSel)) != RT_ERR_OK)
-                return retVal;
-
-            if( (sgmiiSel == 1) || (hsgmiiSel == 1) )
-            {
-                memset(pPortAbility, 0x00, sizeof(rtl8367c_port_ability_t));
-                pPortAbility->forcemode = 1;
-
-                if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_FDUP_OFFSET, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-
-                pPortAbility->duplex = reg_data;
-
-                if((retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_SPD_MASK, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-
-                pPortAbility->speed = reg_data;
-
-                if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_LINK_OFFSET, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-
-                pPortAbility->link = reg_data;
-
-                if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_TXFC_OFFSET, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-
-                pPortAbility->txpause = reg_data;
-
-                if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_SGMII_RXFC_OFFSET, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-
-                pPortAbility->rxpause = reg_data;
-
-                return RT_ERR_OK;
-            }
-        }
-
-        if(0 == id || 1 == id)
-            retVal = rtl8367c_getAsicReg(RTL8367C_REG_DIGITAL_INTERFACE0_FORCE+id, &reg_data);
-        else
-            retVal = rtl8367c_getAsicReg(RTL8367C_REG_DIGITAL_INTERFACE2_FORCE, &reg_data);
-
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        pPortAbility->forcemode = (reg_data >> 12) & 0x0001;
-        pPortAbility->mstfault  = (reg_data >> 9) & 0x0001;
-        pPortAbility->mstmode   = (reg_data >> 8) & 0x0001;
-        pPortAbility->nway      = (reg_data >> 7) & 0x0001;
-        pPortAbility->txpause   = (reg_data >> 6) & 0x0001;
-        pPortAbility->rxpause   = (reg_data >> 5) & 0x0001;
-        pPortAbility->link      = (reg_data >> 4) & 0x0001;
-        pPortAbility->duplex    = (reg_data >> 2) & 0x0001;
-        pPortAbility->speed     = reg_data & 0x0003;
-    }
-    else if (2 == type)
-    {
-        if (id == 1)
-        {
-            if ((retVal = rtl8367c_getAsicReg(0x1311, &reg_data))!=RT_ERR_OK)
-                return retVal;
-
-            pPortAbility->forcemode = (reg_data >> 12) & 1;
-            pPortAbility->duplex = (reg_data >> 2) & 1;
-            pPortAbility->link = (reg_data >> 4) & 1;
-            pPortAbility->speed = reg_data & 3;
-            pPortAbility->rxpause = (reg_data >> 5) & 1;
-            pPortAbility->txpause = (reg_data >> 6) & 1;
-        }
-        else if (2 == id)
-        {
-            if ((retVal = rtl8367c_getAsicReg(0x13c4, &reg_data))!=RT_ERR_OK)
-                return retVal;
-
-            pPortAbility->forcemode = (reg_data >> 12) & 1;
-            pPortAbility->duplex = (reg_data >> 2) & 1;
-            pPortAbility->link = (reg_data >> 4) & 1;
-            pPortAbility->speed = reg_data & 3;
-            pPortAbility->rxpause = (reg_data >> 5) & 1;
-            pPortAbility->txpause = (reg_data >> 6) & 1;
-        }
-    }
-    else if (3 == type)
-    {
-        if (id == 1)
-        {
-            if ((retVal = rtl8367c_getAsicReg(0x1311, &reg_data))!=RT_ERR_OK)
-                return retVal;
-
-            pPortAbility->forcemode = (reg_data >> 12) & 1;
-            pPortAbility->duplex = (reg_data >> 2) & 1;
-            pPortAbility->link = (reg_data >> 4) & 1;
-            pPortAbility->speed = reg_data & 3;
-            pPortAbility->rxpause = (reg_data >> 5) & 1;
-            pPortAbility->txpause = (reg_data >> 6) & 1;
-        }
-        else if (2 == id)
-        {
-            if ((retVal = rtl8367c_getAsicReg(0x13c4, &reg_data))!=RT_ERR_OK)
-                return retVal;
-
-            pPortAbility->forcemode = (reg_data >> 12) & 1;
-            pPortAbility->duplex = (reg_data >> 2) & 1;
-            pPortAbility->link = (reg_data >> 4) & 1;
-            pPortAbility->speed = reg_data & 3;
-            pPortAbility->rxpause = (reg_data >> 5) & 1;
-            pPortAbility->txpause = (reg_data >> 6) & 1;
-        }
-    }
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicPortExtMode
- * Description:
- *      Set external interface mode configuration
- * Input:
- *      id      - external interface id (0~2)
- *      mode    - external interface mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortExtMode(rtk_uint32 id, rtk_uint32 mode)
-{
-    ret_t   retVal;
-    rtk_uint32 i, regValue, type, option,reg_data;
-    rtk_uint32 idx;
-    rtk_uint32 redData[][2] =   { {0x04D7, 0x0480}, {0xF994, 0x0481}, {0x21A2, 0x0482}, {0x6960, 0x0483}, {0x9728, 0x0484}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x83F2, 0x002E} };
-    rtk_uint32 redDataSB[][2] = { {0x04D7, 0x0480}, {0xF994, 0x0481}, {0x31A2, 0x0482}, {0x6960, 0x0483}, {0x9728, 0x0484}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x83F2, 0x002E} };
-    rtk_uint32 redData1[][2] =  { {0x82F1, 0x0500}, {0xF195, 0x0501}, {0x31A2, 0x0502}, {0x796C, 0x0503}, {0x9728, 0x0504}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x0F80, 0x0001}, {0x83F2, 0x002E} };
-    rtk_uint32 redData5[][2] =  { {0x82F1, 0x0500}, {0xF195, 0x0501}, {0x31A2, 0x0502}, {0x796C, 0x0503}, {0x9728, 0x0504}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x0F80, 0x0001}, {0x83F2, 0x002E} };
-    rtk_uint32 redData6[][2] =  { {0x82F1, 0x0500}, {0xF195, 0x0501}, {0x31A2, 0x0502}, {0x796C, 0x0503}, {0x9728, 0x0504}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x0F80, 0x0001}, {0x83F2, 0x002E} };
-    rtk_uint32 redData8[][2] =  { {0x82F1, 0x0500}, {0xF995, 0x0501}, {0x31A2, 0x0502}, {0x796C, 0x0503}, {0x9728, 0x0504}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x0F80, 0x0001}, {0x83F2, 0x002E} };
-    rtk_uint32 redData9[][2] =  { {0x82F1, 0x0500}, {0xF995, 0x0501}, {0x31A2, 0x0502}, {0x796C, 0x0503}, {0x9728, 0x0504}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x0F80, 0x0001}, {0x83F2, 0x002E} };
-    rtk_uint32 redDataHB[][2] = { {0x82F0, 0x0500}, {0xF195, 0x0501}, {0x31A2, 0x0502}, {0x7960, 0x0503}, {0x9728, 0x0504}, {0x9D85, 0x0423}, {0xD810, 0x0424}, {0x0F80, 0x0001}, {0x83F2, 0x002E} };
-
-    if(id >= RTL8367C_EXTNO)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(mode >= EXT_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    /* magic number*/
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-    /* Chip num */
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    type = 0;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 1;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 2;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 3;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-
-    if (1==type)
-    {
-        if((mode == EXT_1000X_100FX) || (mode == EXT_1000X) || (mode == EXT_100FX))
-        {
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_REG_TO_ECO4, 5, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_REG_TO_ECO4, 7, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_CHIP_RESET, RTL8367C_DW8051_RST_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MISCELLANEOUS_CONFIGURE0, RTL8367C_DW8051_EN_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_ACS_IROM_ENABLE_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_IROM_MSB_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-
-            if(mode == EXT_1000X_100FX)
-            {
-                for(idx = 0; idx < FIBER2_AUTO_INIT_SIZE; idx++)
-                {
-                    if ((retVal = rtl8367c_setAsicReg(0xE000 + idx, (rtk_uint32)Fiber2_Auto[idx])) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-
-            if(mode == EXT_1000X)
-            {
-                for(idx = 0; idx < FIBER2_1G_INIT_SIZE; idx++)
-                {
-                    if ((retVal = rtl8367c_setAsicReg(0xE000 + idx, (rtk_uint32)Fiber2_1G[idx])) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-
-            if(mode == EXT_100FX)
-            {
-                for(idx = 0; idx < FIBER2_100M_INIT_SIZE; idx++)
-                {
-                    if ((retVal = rtl8367c_setAsicReg(0xE000 + idx, (rtk_uint32)Fiber2_100M[idx])) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_IROM_MSB_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_ACS_IROM_ENABLE_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_CHIP_RESET, RTL8367C_DW8051_RST_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        if(mode == EXT_GMII)
-        {
-            if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_EXT0_RGMXF, RTL8367C_EXT0_RGTX_INV_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_EXT1_RGMXF, RTL8367C_EXT1_RGTX_INV_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if( (retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_EXT_TXC_DLY, RTL8367C_EXT1_GMII_TX_DELAY_MASK, 5)) != RT_ERR_OK)
-                return retVal;
-
-            if( (retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_EXT_TXC_DLY, RTL8367C_EXT0_GMII_TX_DELAY_MASK, 6)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        /* Serdes reset */
-        if( (mode == EXT_TMII_MAC) || (mode == EXT_TMII_PHY) )
-        {
-            if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_BYPASS_LINE_RATE, id, 1)) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-        {
-            if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_BYPASS_LINE_RATE, id, 0)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        if( (mode == EXT_SGMII) || (mode == EXT_HSGMII) )
-        {
-            if(id != 1)
-                return RT_ERR_PORT_ID;
-
-            if((retVal = rtl8367c_setAsicReg(0x13C0, 0x0249)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicReg(0x13C1, &option)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicReg(0x13C0, 0x0000)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        if(mode == EXT_SGMII)
-        {
-            if(option == 0)
-            {
-                for(i = 0; i <= 7; i++)
-                {
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redData[i][0])) != RT_ERR_OK)
-                        return retVal;
-
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redData[i][1])) != RT_ERR_OK)
-                        return retVal;
-
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-            else
-            {
-                for(i = 0; i <= 7; i++)
-                {
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redDataSB[i][0])) != RT_ERR_OK)
-                        return retVal;
-
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redDataSB[i][1])) != RT_ERR_OK)
-                        return retVal;
-
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-        }
-
-        if(mode == EXT_HSGMII)
-        {
-            if(option == 0)
-            {
-                if( (retVal = rtl8367c_setAsicReg(0x13c2, 0x0249)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicReg(0x1301, &regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(0x13c2, 0x0000)) != RT_ERR_OK)
-                    return retVal;
-
-                if ( ((regValue & 0x00F0) >> 4) == 0x0001)
-                {
-                    for(i = 0; i <= 8; i++)
-                    {
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redData1[i][0])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redData1[i][1])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                }
-                else if ( ((regValue & 0x00F0) >> 4) == 0x0005)
-                {
-                    for(i = 0; i <= 8; i++)
-                    {
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redData5[i][0])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redData5[i][1])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                }
-                else if ( ((regValue & 0x00F0) >> 4) == 0x0006)
-                {
-                    for(i = 0; i <= 8; i++)
-                    {
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redData6[i][0])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redData6[i][1])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                }
-                else if ( ((regValue & 0x00F0) >> 4) == 0x0008)
-                {
-                    for(i = 0; i <= 8; i++)
-                    {
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redData8[i][0])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redData8[i][1])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                }
-                else if ( ((regValue & 0x00F0) >> 4) == 0x0009)
-                {
-                    for(i = 0; i <= 8; i++)
-                    {
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redData9[i][0])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redData9[i][1])) != RT_ERR_OK)
-                            return retVal;
-
-                        if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                            return retVal;
-                    }
-                }
-            }
-            else
-            {
-                for(i = 0; i <= 8; i++)
-                {
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, redDataHB[i][0])) != RT_ERR_OK)
-                        return retVal;
-
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, redDataHB[i][1])) != RT_ERR_OK)
-                        return retVal;
-
-                    if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-        }
-
-        /* Only one ext port should care SGMII setting */
-        if(id == 1)
-        {
-
-            if(mode == EXT_SGMII)
-            {
-                if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_SGMII_OFFSET, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_HSGMII_OFFSET, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if(mode == EXT_HSGMII)
-            {
-                if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_SGMII_OFFSET, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_HSGMII_OFFSET, 1)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else
-            {
-
-                if((mode != EXT_1000X_100FX) && (mode != EXT_1000X) && (mode != EXT_100FX))
-                {
-                    if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_SGMII_OFFSET, 0)) != RT_ERR_OK)
-                        return retVal;
-
-                    if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_HSGMII_OFFSET, 0)) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-        }
-
-        if(0 == id || 1 == id)
-        {
-            if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_DIGITAL_INTERFACE_SELECT, RTL8367C_SELECT_GMII_0_MASK << (id * RTL8367C_SELECT_GMII_1_OFFSET), mode)) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-        {
-            if((retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_DIGITAL_INTERFACE_SELECT_1, RTL8367C_SELECT_GMII_2_MASK, mode)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        /* Serdes not reset */
-        if( (mode == EXT_SGMII) || (mode == EXT_HSGMII) )
-        {
-            if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x7106)) != RT_ERR_OK)
-                return retVal;
-
-            if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, 0x0003)) != RT_ERR_OK)
-                return retVal;
-
-            if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        if( (mode == EXT_SGMII) || (mode == EXT_HSGMII) )
-        {
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_CHIP_RESET, RTL8367C_DW8051_RST_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_MISCELLANEOUS_CONFIGURE0, RTL8367C_DW8051_EN_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_ACS_IROM_ENABLE_OFFSET, 1)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_IROM_MSB_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-
-            for(idx = 0; idx < SGMII_INIT_SIZE; idx++)
-            {
-                if ((retVal = rtl8367c_setAsicReg(0xE000 + idx, (rtk_uint32)Sgmii_Init[idx])) != RT_ERR_OK)
-                    return retVal;
-            }
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_IROM_MSB_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_DW8051_RDY, RTL8367C_ACS_IROM_ENABLE_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_CHIP_RESET, RTL8367C_DW8051_RST_OFFSET, 0)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-    else if (2 == type)
-    {
-        /* Serdes reset */
-        if( (mode == EXT_TMII_MAC) || (mode == EXT_TMII_PHY) )
-        {
-            if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_BYPASS_LINE_RATE, id+2, 1)) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-        {
-            if( (retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_BYPASS_LINE_RATE, id+2, 0)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        /*set MAC mode*/
-        if (id == 1)
-        {
-            if(mode == EXT_HSGMII)
-                return RT_ERR_PORT_ID;
-
-            if (mode == EXT_SGMII)
-            {
-                /*cfg port8 with MII mac mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*enable port8 SGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 14, 1)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (mode == EXT_1000X || mode == EXT_100FX || mode == EXT_1000X_100FX)
-            {
-                /*cfg port8 with MII mac mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port8 SGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 14, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*set fiber link up*/
-                if((retVal = rtl8367c_setAsicRegBit(0x6210, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else
-            {
-                /*cfg port8 with MII mac mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, mode)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port8 SGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 14, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            /*disable SDS 1*/
-            if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 0x1f)) != RT_ERR_OK)
-                return retVal;
-        }
-        else if(id == 2)
-        {
-            if (mode == EXT_HSGMII)
-            {
-                if ((retVal = rtl8367c_setAsicReg(0x130, 7)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0x39f, 7)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0x3fa, 7)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else
-            {
-                if ((retVal = rtl8367c_setAsicReg(0x130, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0x39f, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0x3fa, 4)) != RT_ERR_OK)
-                    return retVal;
-
-            }
-
-
-            if (mode == EXT_SGMII)
-            {
-                /*cfg port9 with MII mac mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*enable port9 SGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 6, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port9 HSGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (mode == EXT_HSGMII)
-            {
-                /*cfg port9 with MII mac mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port9 SGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 6, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*enable port9 HSGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 7, 1)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (mode == EXT_1000X || mode == EXT_100FX || mode == EXT_1000X_100FX)
-            {
-                /*cfg port9 with MII mac mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port9 SGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 6, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port9 HSGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*set fiber link up*/
-                if((retVal = rtl8367c_setAsicRegBit(0x6200, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else
-            {
-                /*cfg port9 with MII mac mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, mode)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port9 SGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 6, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*disable port9 HSGMII*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d92, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            /*disable SDS 0*/
-            if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 0x1f)) != RT_ERR_OK)
-                return retVal;
-        }
-
-        /*SET TO RGMII MODE*/
-        if (mode == EXT_RGMII)
-        {
-            /*disable paral led pad*/
-            if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PARA_LED_IO_EN3, 0)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PARA_LED_IO_EN1, 0)) != RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_setAsicReg(RTL8367C_REG_PARA_LED_IO_EN2, 0)) != RT_ERR_OK)
-                return retVal;
-
-            /*set MAC8 mode*/
-            if (id == 1)
-            {
-                /*1: RGMII1 bias work at 3.3V, 0: RGMII1 bias work at 2.5V*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1303, 9, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*drving 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1303, 6, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*drving 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1303, 4, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*show rate = 0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1303, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*EXT1 RGMII TXC delay 2ns*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1307, 3, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_Ext1_rgtxc_dly = 0*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13f9, 0x38, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*RXDLY = 0*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1307, 0x7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_rg1_dn = 4*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1304, 0x7000, 4)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_rg1_dp = 4*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13f9, 0x700, 4)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (id == 2)
-            {
-                /*1: RGMII1 bias work at 3.3V, 0: RGMII1 bias work at 2.5V*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1303, 10, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*drving 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x13e2, 2, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*drving 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x13e2, 1, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*show rate = 0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x13e2, 0, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*EXT1 RGMII TXC delay 2ns*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x13c5, 3, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_Ext1_rgtxc_dly = 0*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13f9, 0x1c0, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*RXDLY = 0*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c5, 0x7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_rg1_dn = 4*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13e2, 0x1c0, 4)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_rg1_dp = 4*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13e2, 0x38, 4)) != RT_ERR_OK)
-                    return retVal;
-            }
-        }
-        else if (mode == EXT_SGMII)
-        {
-            if (id == 1)
-            {
-                /*sds 1     reg 1    page 0x21     write value  0xec91*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0xec91)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x21<<5) | 1)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*sds 1     reg 5    page 0x24     write value  0x5825*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x5825)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x24<<5) | 5)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C1)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 2)) != RT_ERR_OK)
-                    return retVal;
-
-                /*?????????????????*/
-
-            }
-            else if (id == 2)
-            {
-                /*sds 0     reg 0    page 0x28     write value  0x942c*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x28<<5) | 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*sds 0     reg 0    page 0x24     write value  0x942c*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x24<<5) | 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*sds 0     reg 5    page 0x21     write value  0x8dc3*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x8dc3)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x21<<5) | 5)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 2)) != RT_ERR_OK)
-                    return retVal;
-
-                /*?????????????????*/
-            }
-        }
-        else if (mode == EXT_HSGMII)
-        {
-            if (id == 2)
-            {
-                /*sds 0     reg 0    page 0x28     write value  0x942c*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x28<<5) | 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*sds 0     reg 0    page 0x24     write value  0x942c*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x24<<5) | 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*sds 0     reg 5    page 0x21     write value  0x8dc3*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x8dc3)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x21<<5) | 5)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                    return retVal;
-
-
-                /* optimizing HISGMII performance while RGMII used & */
-                /*sds 0     reg 9     page 0x21     write value 0x3931*/
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_DATA, 0x3931)) != RT_ERR_OK)
-                        return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_ADR, (0x21<<5)|9) ) != RT_ERR_OK)
-                        return retVal;
-
-                if( (retVal = rtl8367c_setAsicReg(RTL8367C_REG_SDS_INDACS_CMD, 0x00C0)) != RT_ERR_OK)
-                        return retVal;
-
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 0x12)) != RT_ERR_OK)
-                    return retVal;
-
-                /*?????????????????*/
-            }
-        }
-        else if (mode == EXT_1000X)
-        {
-            if (id == 1)
-            {
-
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 1, 0x21, 0xec91)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 5, 0x24, 0x5825)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 4)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                /*patch speed change sds1 1000M*/
-                if( (retVal = rtl8367c_getAsicSdsReg(1, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFF0FFF;
-                regValue |= 0x9000;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(1, 0, 2, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFdFFF;
-                regValue |= 0x40;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 0, 2, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-
-                if( (retVal = rtl8367c_getAsicSdsReg(1, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFEFFF;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 4)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x6000, 0)) != RT_ERR_OK)
-                    return retVal;
-
-            }
-            else if (id == 2)
-            {
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 0x28, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 0x24, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 5, 0x21, 0x8dc3)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 4)) != RT_ERR_OK)
-                    return retVal;
-
-                /*patch speed change sds0 1000M*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFF0FFF;
-                regValue |= 0x9000;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFDFFF;
-                regValue |= 0x40;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 2, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFEFFF;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 4)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0xe0, 0)) != RT_ERR_OK)
-                    return retVal;
-
-            }
-        }
-        else if (mode == EXT_100FX)
-        {
-            if (id == 1)
-            {
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 1, 0x21, 0xec91)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 5, 0x24, 0x5825)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 5)) != RT_ERR_OK)
-                    return retVal;
-
-                /*patch speed change sds1 100M*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_getAsicSdsReg(1, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFF0FFF;
-                regValue |= 0xb000;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(1, 0, 2, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFFFBF;
-                regValue |= 0x2000;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 0, 2, regValue)) != RT_ERR_OK)
-                    return retVal;
-#if 0
-                if( (retVal = rtl8367c_setAsicReg(0x6214, 0x1a0)) != RT_ERR_OK)
-                    return retVal;
-#endif
-                if( (retVal = rtl8367c_getAsicSdsReg(1, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFEFFF;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 5)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x6000, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (id == 2)
-            {
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 0x28, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 0x24, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 5, 0x21, 0x8dc3)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 5)) != RT_ERR_OK)
-                    return retVal;
-
-                /*patch speed change sds0 100M*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFF0FFF;
-                regValue |= 0xb000;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(0, 0, 2, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFFFBF;
-                regValue |= 0x2000;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 2, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if( (retVal = rtl8367c_getAsicSdsReg(0, 4, 0, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue &= 0xFFFFEFFF;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 4, 0, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 5)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0xe0, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-        }
-        else if (mode == EXT_1000X_100FX)
-        {
-            if (id == 1)
-            {
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 1, 0x21, 0xec91)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 5, 0x24, 0x5825)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 13, 0, 0x4616)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(1, 1, 0, 0xf20)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f00, 7)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (id == 2)
-            {
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 0x28, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 0, 0x24, 0x942c)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 5, 0x21, 0x8dc3)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 13, 0, 0x4616)) != RT_ERR_OK)
-                    return retVal;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 1, 0, 0xf20)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d92, 0x1f, 7)) != RT_ERR_OK)
-                    return retVal;
-            }
-        }
-
-    }
-    else if (3 == type)
-    {
-
-        /*restore patch, by designer. patch Tx FIFO issue, when not HSGMII 2.5G mode
-         #sds0, page 1, reg 1, bit4=0*/
-        if( (retVal = rtl8367c_getAsicSdsReg(0, 1, 1, &regValue)) != RT_ERR_OK)
-            return retVal;
-        regValue &= 0xFFFFFFEF;
-        if( (retVal = rtl8367c_setAsicSdsReg(0, 1, 1, regValue)) != RT_ERR_OK)
-            return retVal;
-
-        /*set for mac 6*/
-        if (1 == id)
-        {
-            /*force port6 linkdown*/
-            if ((retVal = rtl8367c_setAsicReg(0x137c, 0x1000)) != RT_ERR_OK)
-                    return retVal;
-
-            if ((retVal = rtl8367c_getAsicRegBit(0x1d9d, 6, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-            while(reg_data == 0)
-            {
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d9d, 6, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-            }
-
-            if (mode == EXT_SGMII)
-            {
-                /* disable mac6 mode_ext1  mode*/
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d3d, 10, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                if(reg_data == 0)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 0)) != RT_ERR_OK)
-                        return retVal;
-                }
-                /*cfg_bypass_line_rate[1]=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-
-
-                /*bit5: cfg_mac6_fib=0    &   bit7: cfg_mac6_fib2=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_fib=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 0: MAC7 is not SGMII mode*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 0, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*#cfg_sgmii_link=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 9, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_hsgmii=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-
-
-                /*bit13: cfg_sds_mode_sel_new=1 :Enable new sds mode config method*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x1F (reset mode) */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_sgmii= 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /* bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                   new_cfg_sds_mode=0x12  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x2)) != RT_ERR_OK)
-                    return retVal;
-
-                /* MAC link source*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-
-            }
-            else if (mode == EXT_HSGMII)
-            {
-
-                /*restore patch, by designer. patch Tx FIFO issue, when  HSGMII 2.5G mode
-                 #sds0, page 1, reg 1, bit4=1*/
-                if( (retVal = rtl8367c_getAsicSdsReg(0, 1, 1, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                regValue |= 0x10;
-                if( (retVal = rtl8367c_setAsicSdsReg(0, 1, 1, regValue)) != RT_ERR_OK)
-                    return retVal;
-
-                 /* mode_ext1 = disable*/
-                /* disable mac6 mode_ext1  mode*/
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d3d, 10, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                if(reg_data == 0)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 0)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit5: cfg_mac6_fib=0   &   bit7: cfg_mac6_fib2=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_fib=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 0, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_sgmii=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 9, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_hsgmii=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_sgmii= 0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0xd0,7)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicReg(0x399, 7)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicReg(0x3fa, 7)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit13: cfg_sds_mode_sel_new=1 :Enable new sds mode config method*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-                /* bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                   new_cfg_sds_mode=0x12  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x12)) != RT_ERR_OK)
-                    return retVal;
-                /*
-                1: MAC link = SGMII SerDes link
-                0: MAC link = SGMII config link £¨cfg_sgmii_link£©
-                */
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-            }
-            else if(mode == EXT_1000X)
-            {
-                /* 0 2 0  bit 8~9  set 0, force n-way*/
-                if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                reg_data &= 0xFFFFFCFF;
-                if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                /* disable mac6 mode_ext1  mode*/
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d3d, 10, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                if(reg_data == 0)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 0)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0x1d11, 0x1500)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit13: cfg_sds_mode_sel_new=1 :Enable new sds mode config method
-                  bit[1:0]:cfg_mac7_fib= 0  &  cfg_mac7_sel_sgmii=0
-                */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* bit0 :UTP/Fiber auto detect function enable or not, cfg_dis_det=1:disable
-                   bit3:Force UTP/Fiber auto detect function enable or not, cfg_force_auto-detect=1 */
-                if ((retVal = rtl8367c_setAsicReg(0x13eb, 0x15bb)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit3:  Serdes force mode:cfg_sds_frc_mode=1
-                  bit[2:0]: Serdes chip mode, cfg_sds_mode=3b'100 (force sds FIB1G mode) */
-                if ((retVal = rtl8367c_setAsicReg(0x13e7, 0xc)) != RT_ERR_OK)
-                    return retVal;
-
-
-                /*bit5: cfg_mac6_fib=1 & bit7: cfg_mac6_fib2=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 1)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_hsgmii=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_sgmii= 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /* bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                   new_cfg_sds_mode=0x4  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x4)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if(mode == EXT_100FX)
-            {
-                /* 0 2 0  bit 8~9  set 0, force n-way*/
-                if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                reg_data &= 0xFFFFFCFF;
-                if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                /* disable mac6 mode_ext1  mode*/
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d3d, 10, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                if(reg_data == 0)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 0)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0x1d11, 0x1500)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit13: cfg_sds_mode_sel_new=1 :Enable new sds mode config method
-                  bit[1:0]:cfg_mac7_fib= 0  &  cfg_mac7_sel_sgmii=0
-                */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* bit0 :UTP/Fiber auto detect function enable or not, cfg_dis_det=1:disable
-                   bit3:Force UTP/Fiber auto detect function enable or not, cfg_force_auto-detect=1 */
-                if ((retVal = rtl8367c_setAsicReg(0x13eb, 0x15bb)) != RT_ERR_OK)
-                    return retVal;
-
-                /*!!!!! cfg_sds_frc_mode=1 &  cfg_sds_mode=3b'101 (force sds fib100M mode)*/
-                if ((retVal = rtl8367c_setAsicReg(0x13e7, 0xc)) != RT_ERR_OK)
-                    return retVal;
-
-
-                /*bit5: cfg_mac6_fib=1 & bit7: cfg_mac6_fib2=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 1)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_hsgmii=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_sgmii= 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x5 */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x5)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if(mode == EXT_1000X_100FX)
-            {
-                /* 0 2 0  bit 8~9  set 0, force n-way*/
-                if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                reg_data &= 0xFFFFFCFF;
-                if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                /* disable mac6 mode_ext1  mode*/
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d3d, 10, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                if(reg_data == 0)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 0)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicReg(0x1d11, 0x1500)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit13: cfg_sds_mode_sel_new=1 :Enable new sds mode config method
-                  bit[1:0]:cfg_mac7_fib= 0  &  cfg_mac7_sel_sgmii=0
-                */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* bit0 :UTP/Fiber auto detect function enable or not, cfg_dis_det=1:disable
-                   bit3:Force UTP/Fiber auto detect function enable or not, cfg_force_auto-detect=1 */
-                if ((retVal = rtl8367c_setAsicReg(0x13eb, 0x15bb)) != RT_ERR_OK)
-                    return retVal;
-
-                /*!!!!!! cfg_sds_frc_mode=1 &  cfg_sds_mode=3'b111: Fib1G/Fib100M auto detect */
-                if ((retVal = rtl8367c_setAsicReg(0x13e7, 0xc)) != RT_ERR_OK)
-                    return retVal;
-
-
-                /*bit5: cfg_mac6_fib=1 & bit7: cfg_mac6_fib2=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 1)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_hsgmii=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_sgmii= 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x7 */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x7)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if(mode < EXT_SGMII)
-            {
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d3d, 10, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 1, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* keep default setting, disable mac6 sel SerDes mode,*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit5: cfg_mac6_fib=0       &        bit7: cfg_mac6_fib2=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if (mode < EXT_GMII)
-                {
-                    /* set mac6 mode*/
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, mode)) != RT_ERR_OK)
-                        return retVal;
-                }
-                else if(mode == EXT_RMII_MAC)
-                {
-                    /*!!!!!!*/
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 7)) != RT_ERR_OK)
-                        return retVal;
-                }
-                else if(mode == EXT_RMII_PHY)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, 8)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-                if ((mode == EXT_TMII_MAC) || (mode == EXT_TMII_PHY))
-                {
-                    if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 1, 1)) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-
-        }
-        else if (2 == id)
-        {
-
-            /*force port7 linkdown*/
-            if ((retVal = rtl8367c_setAsicReg(0x137d, 0x1000)) != RT_ERR_OK)
-                    return retVal;
-
-            if ((retVal = rtl8367c_getAsicRegBit(0x1d9d, 7, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-            while(reg_data == 0)
-            {
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d9d, 7, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-            }
-
-            if (mode == EXT_SGMII)
-            {
-                /*disable mac7 sel ext2 xMII mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf,0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*restore ext2 ability*/
-                if ((retVal = rtl8367c_setAsicReg(0x13c4, 0)) != RT_ERR_OK)
-                    return retVal;
-                /*  disable mac7  mode_ext2  */
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit5: cfg_mac6_fib=0 & bit7: cfg_mac6_fib2=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*
-                   bit0:cfg_mac7_sel_sgmii=0,MAC7 is not SGMII mode
-                   bit1:cfg_mac7_fib= 0  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_hsgmii=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 11, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac6_sel_sgmii= 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*Enable new sds mode config method, cfg_sds_mode_sel_new=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x1F (reset mode) */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 0, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x2 (SGMII mode)*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x2)) != RT_ERR_OK)
-                    return retVal;
-
-                /*select MAC link source when port6/7 be set sgmii mode £¨cfg_sgmii_link£©*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (mode == EXT_1000X)
-            {
-                /*  disable mac7 MII/TMM/RMII/GMII/RGMII mode, mode_ext2 = disable */
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*restore ext2 ability*/
-                if ((retVal = rtl8367c_setAsicReg(0x13c4, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* 0 2 0  bit 8~9  set 0, force n-way*/
-                if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                reg_data &= 0xFFFFFCFF;
-                if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                /*restore ext2 ability*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  keep default setting, disable mac6 sel serdes*/
-                if ((retVal = rtl8367c_setAsicReg(0x1d11, 0x1500)) != RT_ERR_OK)
-                    return retVal;
-
-                /*Enable new sds mode config method, cfg_sds_mode_sel_new=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x1F (reset mode) */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit5: cfg_mac6_fib=0         &        bit7: cfg_mac6_fib2=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 1 & cfg_mac7_fib=1*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 3)) != RT_ERR_OK)
-                    return retVal;
-
-                /*new_cfg_sds_mode=0x4 (FIB1000 mode)*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x4)) != RT_ERR_OK)
-                    return retVal;
-
-            }
-            else if (mode == EXT_100FX)
-            {
-                /*  disable mac7 MII/TMM/RMII/GMII/RGMII mode, mode_ext2 = disable  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*restore ext2 ability*/
-                if ((retVal = rtl8367c_setAsicReg(0x13c4, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* 0 2 0  bit 8~9  set 0, force n-way*/
-                if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                reg_data &= 0xFFFFFCFF;
-                if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                /*restore ext2 ability*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* keep default setting, disable mac6 sel serdes*/
-                if ((retVal = rtl8367c_setAsicReg(0x1d11, 0x1500)) != RT_ERR_OK)
-                    return retVal;
-
-                /*Enable new sds mode config method, cfg_sds_mode_sel_new=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x1F (reset mode) */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit5: cfg_mac6_fib=0       &       bit7: cfg_mac6_fib2=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 1 & cfg_mac7_fib=1*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 3)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x5  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x5)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (mode == EXT_1000X_100FX)
-            {
-                /*  disable mac7 MII/TMM/RMII/GMII/RGMII mode, mode_ext2 = disable  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*restore ext2 ability*/
-                if ((retVal = rtl8367c_setAsicReg(0x13c4, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* 0 2 0  bit 8~9  set 0, force n-way*/
-                if((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                reg_data &= 0xFFFFFCFF;
-                if((retVal = rtl8367c_setAsicSdsReg(0,2,0, reg_data)) != RT_ERR_OK)
-                        return retVal;
-
-                /*restore ext2 ability*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* keep default setting, disable mac6 sel serdes*/
-                if ((retVal = rtl8367c_setAsicReg(0x1d11, 0x1500)) != RT_ERR_OK)
-                    return retVal;
-
-                /*Enable new sds mode config method, cfg_sds_mode_sel_new=1*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d95, 13, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x1F (reset mode) */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x1f)) != RT_ERR_OK)
-                    return retVal;
-
-                /*bit5: cfg_mac6_fib=0    &    bit7: cfg_mac6_fib2=0*/
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 5, 0)) != RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d41, 7, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 1 & cfg_mac7_fib=1*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 3)) != RT_ERR_OK)
-                    return retVal;
-
-                /*  bit[12:8]: Only valid when cfg_sds_mode_sel_new=1
-                    new_cfg_sds_mode=0x7  */
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 0x1f00, 0x7)) != RT_ERR_OK)
-                    return retVal;
-            }
-            else if (mode < EXT_SGMII)
-            {
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d3d, 10, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* keep default setting, disable mac7 sel SerDes mode*/
-                if ((retVal = rtl8367c_setAsicReg(0x1d95, 0x1f00)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 0 & cfg_mac7_fib=0*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /* set port7 mode*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x13c3, 0xf, mode)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((mode == EXT_TMII_MAC) || (mode == EXT_TMII_PHY))
-                {
-                    if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 1)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-            }
-            else if ((mode < EXT_END) && (mode > EXT_100FX))
-            {
-                if ((retVal = rtl8367c_setAsicRegBits(0x13C3, 0xf, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                /*cfg_mac7_sel_sgmii= 0 & cfg_mac7_fib=0*/
-                if ((retVal = rtl8367c_setAsicRegBits(0x1d95, 3, 0)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_setAsicRegBit(0x1d3d, 10, 1)) != RT_ERR_OK)
-                    return retVal;
-
-                if ((retVal = rtl8367c_getAsicRegBit(0x1d11, 11, &reg_data)) != RT_ERR_OK)
-                    return retVal;
-                if(reg_data == 0)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBit(0x1d11, 6, 1)) != RT_ERR_OK)
-                        return retVal;
-                }
-
-                /* set port7 mode*/
-                if (mode < EXT_RMII_MAC_2)
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, (mode-13))) != RT_ERR_OK)
-                        return retVal;
-                }
-                else
-                {
-                    if ((retVal = rtl8367c_setAsicRegBits(0x1305, 0xf0, (mode-12))) != RT_ERR_OK)
-                        return retVal;
-                }
-
-                if ((mode == EXT_TMII_MAC_2) || (mode == EXT_TMII_PHY_2))
-                {
-                    if ((retVal = rtl8367c_setAsicRegBit(0x3f7, 2, 1)) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-
-        }
-
-    }
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicPortExtMode
- * Description:
- *      Get external interface mode configuration
- * Input:
- *      id      - external interface id (0~1)
- *      pMode   - external interface mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortExtMode(rtk_uint32 id, rtk_uint32 *pMode)
-{
-    ret_t   retVal;
-    rtk_uint32 regData, regValue, type;
-
-    if(id >= RTL8367C_EXTNO)
-        return RT_ERR_OUT_OF_RANGE;
-    /*cfg_magic_id  &  get chip_id*/
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    type = 0;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 1;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 2;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 3;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-
-    if (1 == type)
-    {
-
-        if (1 == id)
-        {
-            if( (retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_SGMII_OFFSET, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            if(1 == regData)
-            {
-                *pMode = EXT_SGMII;
-                return RT_ERR_OK;
-            }
-
-            if( (retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SDS_MISC, RTL8367C_CFG_MAC8_SEL_HSGMII_OFFSET, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            if(1 == regData)
-            {
-                *pMode = EXT_HSGMII;
-                return RT_ERR_OK;
-            }
-        }
-
-        if(0 == id || 1 == id)
-            return rtl8367c_getAsicRegBits(RTL8367C_REG_DIGITAL_INTERFACE_SELECT, RTL8367C_SELECT_GMII_0_MASK << (id * RTL8367C_SELECT_GMII_1_OFFSET), pMode);
-        else
-           return rtl8367c_getAsicRegBits(RTL8367C_REG_DIGITAL_INTERFACE_SELECT_1, RTL8367C_SELECT_GMII_2_MASK, pMode);
-
-    }
-    else if (2 == type)
-    {
-        if (1 == id)
-        {
-            if ((retVal = rtl8367c_getAsicReg(0x1d92, &regData))!=RT_ERR_OK)
-                return retVal;
-
-            if (regData & 0x4000)
-            {
-                *pMode = EXT_SGMII;
-                return RT_ERR_OK;
-            }
-
-            else if (((regData >> 8) & 0x1f) == 4)
-            {
-                *pMode = EXT_1000X;
-                return RT_ERR_OK;
-            }
-            else if (((regData >> 8) & 0x1f) == 5)
-            {
-                *pMode = EXT_100FX;
-                return RT_ERR_OK;
-            }
-            else if (((regData >> 8) & 0x1f) == 7)
-            {
-                *pMode = EXT_1000X_100FX;
-                return RT_ERR_OK;
-            }
-
-            return rtl8367c_getAsicRegBits(0x1305, 0xf0, pMode);
-        }
-        else if (2 == id)
-        {
-#if 0
-            if ((retVal = rtl8367c_getAsicRegBit(0x1d92, 6, &regData))!=RT_ERR_OK)
-                return retVal;
-
-            if (regData == 1)
-            {
-                *pMode = EXT_SGMII;
-                return RT_ERR_OK;
-            }
-
-            if ((retVal = rtl8367c_getAsicRegBit(0x1d92, 7, &regData))!=RT_ERR_OK)
-                return retVal;
-
-            if (regData == 1)
-            {
-                *pMode = EXT_HSGMII;
-                return RT_ERR_OK;
-            }
-#endif
-            if ((retVal = rtl8367c_getAsicReg(0x1d92, &regData))!=RT_ERR_OK)
-                return retVal;
-
-            if (regData & 0x40)
-            {
-                *pMode = EXT_SGMII;
-                return RT_ERR_OK;
-            }
-            else if (regData & 0x80)
-            {
-                *pMode = EXT_HSGMII;
-                return RT_ERR_OK;
-            }
-            else if ((regData & 0x1f) == 4)
-            {
-                *pMode = EXT_1000X;
-                return RT_ERR_OK;
-            }
-            else if ((regData & 0x1f) == 5)
-            {
-                *pMode = EXT_100FX;
-                return RT_ERR_OK;
-            }
-            else if ((regData & 0x1f) == 7)
-            {
-                *pMode = EXT_1000X_100FX;
-                return RT_ERR_OK;
-            }
-
-            return rtl8367c_getAsicRegBits(0x1305, 0xf, pMode);
-        }
-    }
-    else if(3 == type)
-    {
-        if (1 == id)
-        {
-            /* SDS_CFG_NEW */
-            if ((retVal = rtl8367c_getAsicReg(0x1d95, &regData))!=RT_ERR_OK)
-                return retVal;
-
-            if ((retVal = rtl8367c_getAsicReg(0x1d41, &regValue))!=RT_ERR_OK)
-                return retVal;
-
-            /* bit5: cfg_mac6_fib=1  &&  bit7: cfg_mac6_fib2 =1 */
-            if((regValue & 0xa0)  == 0xa0 )
-            {
-                /* new_cfg_sds_mode */
-                regData = regData >> 8;
-                if((regData & 0x1f) == 4)
-                {
-                    *pMode = EXT_1000X;
-                     return RT_ERR_OK;
-                }
-                else if((regData & 0x1f) == 5)
-                {
-                    *pMode = EXT_100FX;
-                     return RT_ERR_OK;
-                }
-                else if((regData & 0x1f) == 7)
-                {
-                    *pMode = EXT_1000X_100FX;
-                     return RT_ERR_OK;
-                }
-
-            }
-
-
-            if ((retVal = rtl8367c_getAsicReg(0x1d11, &regData))!=RT_ERR_OK)
-                return retVal;
-
-            /* check cfg_mac6_sel_sgmii */
-            if((regData >> 6) & 1)
-            {
-                *pMode = EXT_SGMII;
-                return RT_ERR_OK;
-            }
-            else if((regData >> 11) & 1)
-            {
-                *pMode = EXT_HSGMII;
-                return RT_ERR_OK;
-            }
-            else
-            {
-                /* check port6 MAC mode */
-                if ((retVal = rtl8367c_getAsicRegBits(0x1305, 0xf0, &regData))!=RT_ERR_OK)
-                    return retVal;
-
-                if(regData < 6)
-                    *pMode = regData;
-                else if(regData == 6)
-                    *pMode = EXT_RMII_MAC;
-                else if(regData == 7)
-                    *pMode = EXT_RMII_PHY;
-
-                return RT_ERR_OK;
-            }
-        }
-        else if (2 == id)
-        {
-            if ((retVal = rtl8367c_getAsicReg(0x1d95, &regData))!=RT_ERR_OK)
-                return retVal;
-
-            /* bit0: cfg_mac7_sel_sgmii
-               bit1: cfg_mac7_fib
-               bit[12:8]: new_cfg_sds_mode*/
-            if(((regData & 0x3) == 3) && (((regData >> 8) & 0x1f) == 0x4))
-            {
-                *pMode = EXT_1000X;
-                    return RT_ERR_OK;
-            }
-            else if (((regData & 0x3) == 3) && (((regData >> 8) & 0x1f) == 0x5))
-            {
-                *pMode = EXT_100FX;
-                    return RT_ERR_OK;
-            }
-            else if (((regData & 0x3) == 3) && (((regData >> 8) & 0x1f) == 0x7))
-            {
-                *pMode = EXT_1000X_100FX;
-                    return RT_ERR_OK;
-            }
-            else if(regData & 1)
-            {
-                *pMode = EXT_SGMII;
-                return RT_ERR_OK;
-            }
-            else
-            {
-            /* check port7 MAC mode */
-                if ((retVal = rtl8367c_getAsicRegBits(0x13c3, 0xf, &regData))!=RT_ERR_OK)
-                    return retVal;
-
-                *pMode = regData;
-
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8370_setAsicPortEnableAll
- * Description:
- *      Set ALL ports enable.
- * Input:
- *      enable - enable all ports.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortEnableAll(rtk_uint32 enable)
-{
-    if(enable >= 2)
-        return RT_ERR_INPUT;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_PHY_AD, RTL8367C_PDNPHY_OFFSET, !enable);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPortEnableAll
- * Description:
- *      Set ALL ports enable.
- * Input:
- *      enable - enable all ports.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortEnableAll(rtk_uint32 *pEnable)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_PHY_AD, RTL8367C_PDNPHY_OFFSET, &regData);
-    if(retVal !=  RT_ERR_OK)
-        return retVal;
-
-    if (regData==0)
-        *pEnable = 1;
-    else
-        *pEnable = 0;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicPortSmallIpg
- * Description:
- *      Set small ipg egress mode
- * Input:
- *      port    - Physical port number (0~7)
- *      enable  - 0: normal, 1: small
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortSmallIpg(rtk_uint32 port, rtk_uint32 enable)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_PORT_SMALL_IPG_REG(port), RTL8367C_PORT0_MISC_CFG_SMALL_TAG_IPG_OFFSET, enable);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPortSmallIpg
- * Description:
- *      Get small ipg egress mode
- * Input:
- *      port    - Physical port number (0~7)
- *      pEnable     - 0: normal, 1: small
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortSmallIpg(rtk_uint32 port, rtk_uint32* pEnable)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_PORT_SMALL_IPG_REG(port), RTL8367C_PORT0_MISC_CFG_SMALL_TAG_IPG_OFFSET, pEnable);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortLoopback
- * Description:
- *      Set MAC loopback
- * Input:
- *      port    - Physical port number (0~7)
- *      enable  - 0: Disable, 1: enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortLoopback(rtk_uint32 port, rtk_uint32 enable)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_PORT_MISC_CFG_REG(port), RTL8367C_PORT0_MISC_CFG_MAC_LOOPBACK_OFFSET, enable);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPortLoopback
- * Description:
- *      Set MAC loopback
- * Input:
- *      port    - Physical port number (0~7)
- * Output:
- *      pEnable - 0: Disable, 1: enable
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortLoopback(rtk_uint32 port, rtk_uint32 *pEnable)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_PORT_MISC_CFG_REG(port), RTL8367C_PORT0_MISC_CFG_MAC_LOOPBACK_OFFSET, pEnable);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortRTCTEnable
- * Description:
- *      Set RTCT Enable echo response mode
- * Input:
- *      portmask    - Port mask of RTCT enabled (0-4)
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid port mask
- * Note:
- *      RTCT test takes 4.8 seconds at most.
- */
-ret_t rtl8367c_setAsicPortRTCTEnable(rtk_uint32 portmask)
-{
-    ret_t       retVal;
-    rtk_uint32  regData;
-    rtk_uint32  port;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if( (regData == 0x0276) || (regData == 0x0597) )
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    for(port = 0; port <= 10 ; port++)
-    {
-        if(portmask & (0x0001 << port))
-        {
-             if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa422, &regData)) != RT_ERR_OK)
-                 return retVal;
-
-             regData &= 0x7FFF;
-             if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa422, regData)) != RT_ERR_OK)
-                 return retVal;
-
-             regData |= 0x00F2;/*RTCT set to  echo response mode*/
-             if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa422, regData)) != RT_ERR_OK)
-                 return retVal;
-
-             regData |= 0x0001;
-             if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa422, regData)) != RT_ERR_OK)
-                 return retVal;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortRTCTDisable
- * Description:
- *      Set RTCT Disable
- * Input:
- *      portmask    - Port mask of RTCT enabled (0-4)
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid port mask
- * Note:
- *      RTCT test takes 4.8 seconds at most.
- */
-ret_t rtl8367c_setAsicPortRTCTDisable(rtk_uint32 portmask)
-{
-    ret_t       retVal;
-    rtk_uint32  regData;
-    rtk_uint32  port;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if( (regData == 0x0276) || (regData == 0x0597) )
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    for(port = 0; port <= 10 ; port++)
-    {
-        if(portmask & (0x0001 << port))
-        {
-             if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa422, &regData)) != RT_ERR_OK)
-                 return retVal;
-
-             regData &= 0x7FFF;
-             if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa422, regData)) != RT_ERR_OK)
-                 return retVal;
-
-             regData |= 0x00F0;
-             if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa422, regData)) != RT_ERR_OK)
-                 return retVal;
-
-             regData &= ~0x0001;
-             if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa422, regData)) != RT_ERR_OK)
-                 return retVal;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtl8367c_getAsicPortRTCTResult
- * Description:
- *      Get RTCT result
- * Input:
- *      port    - Port ID of RTCT result
- * Output:
- *      pResult - The result of port ID
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_MASK            - Invalid port mask
- *      RT_ERR_PHY_RTCT_NOT_FINISH  - RTCT test doesn't finish.
- * Note:
- *      RTCT test takes 4.8 seconds at most.
- *      If this API returns RT_ERR_PHY_RTCT_NOT_FINISH,
- *      users should wait a whole then read it again.
- */
-ret_t rtl8367c_getAsicPortRTCTResult(rtk_uint32 port, rtl8367c_port_rtct_result_t *pResult)
-{
-    ret_t       retVal;
-    rtk_uint32  regData, finish = 1;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    if( (regData == 0x6367) )
-    {
-        if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa422, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        if((regData & 0x8000) == 0x8000)
-        {
-            /* Channel A */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802a)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelAOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelAShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelAMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelALinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel B */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802e)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelBOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelBShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelBMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelBLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel C */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8032)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelCOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelCShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelCMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelCLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel D */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8036)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelDOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelDShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelDMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelDLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel A Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802c)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelALen = (regData / 2);
-
-            /* Channel B Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8030)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelBLen = (regData / 2);
-
-            /* Channel C Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8034)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelCLen = (regData / 2);
-
-            /* Channel D Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8038)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelDLen = (regData / 2);
-        }
-        else
-            finish = 0;
-    }
-    else if(regData == 0x6368)
-    {
-        if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa422, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        if((regData & 0x8000) == 0x8000)
-        {
-            /* Channel A */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802b)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelAOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelAShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelAMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelALinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel B */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802f)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelBOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelBShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelBMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelBLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel C */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8033)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelCOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelCShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelCMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelCLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel D */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8037)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelDOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelDShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelDMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelDLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel A Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802d)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelALen = (regData / 2);
-
-            /* Channel B Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8031)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelBLen = (regData / 2);
-
-            /* Channel C Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8035)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelCLen = (regData / 2);
-
-            /* Channel D Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8039)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelDLen = (regData / 2);
-        }
-        else
-            finish = 0;
-
-    }
-    else if((regData == 0x6511) || (regData == 0x0801))
-    {
-        if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa422, &regData)) != RT_ERR_OK)
-            return retVal;
-
-        if((regData & 0x8000) == 0x8000)
-        {
-            /* Channel A */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802a)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelAOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelAShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelAMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelALinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel B */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802e)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelBOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelBShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelBMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelBLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel C */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8032)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelCOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelCShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelCMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelCLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel D */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8036)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelDOpen       = (regData == 0x0048) ? 1 : 0;
-            pResult->channelDShort      = (regData == 0x0050) ? 1 : 0;
-            pResult->channelDMismatch   = ((regData == 0x0042) || (regData == 0x0044)) ? 1 : 0;
-            pResult->channelDLinedriver = (regData == 0x0041) ? 1 : 0;
-
-            /* Channel A Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x802c)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelALen = (regData / 2);
-
-            /* Channel B Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8030)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelBLen = (regData / 2);
-
-            /* Channel C Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8034)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelCLen = (regData / 2);
-
-            /* Channel D Length */
-            if((retVal = rtl8367c_setAsicPHYOCPReg(port, 0xa436, 0x8038)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_getAsicPHYOCPReg(port, 0xa438, &regData)) != RT_ERR_OK)
-                return retVal;
-
-            pResult->channelDLen = (regData / 2);
-        }
-        else
-            finish = 0;
-
-    }
-    else
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    if(finish == 0)
-        return RT_ERR_PHY_RTCT_NOT_FINISH;
-    else
-        return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_sdsReset
- * Description:
- *      Reset Serdes
- * Input:
- *      id  - EXT ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *      None.
- */
-ret_t rtl8367c_sdsReset(rtk_uint32 id)
-{
-    rtk_uint32 retVal, regValue, state, i, option, running = 0, retVal2;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            option = 0;
-            break;
-        case 0x0652:
-        case 0x6368:
-            option = 1;
-            break;
-        case 0x0801:
-        case 0x6511:
-            option = 2;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    if(option == 0)
-    {
-        if (1 == id)
-        {
-            if ((retVal = rtl8367c_getAsicRegBit(0x130c, 5, &running))!=RT_ERR_OK)
-                return retVal;
-
-            if(running == 1)
-            {
-                if ((retVal = rtl8367c_setAsicRegBit(0x130c, 5, 0))!=RT_ERR_OK)
-                    return retVal;
-            }
-
-            retVal = rtl8367c_setAsicReg(0x6601, 0x0000);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6602, 0x1401);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6600, 0x00C0);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6601, 0x0000);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6602, 0x1403);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6600, 0x00C0);
-
-            if(running == 1)
-            {
-                if ((retVal2 = rtl8367c_setAsicRegBit(0x130c, 5, 1))!=RT_ERR_OK)
-                    return retVal2;
-            }
-
-            if(retVal != RT_ERR_OK)
-                return retVal;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(option == 1)
-    {
-        if (1 == id)
-        {
-            if((retVal = rtl8367c_getAsicReg(0x1311, &state)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicReg(0x1311, 0x66)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicReg(0x1311, 0x1066)) != RT_ERR_OK)
-                return retVal;
-
-            while(1)
-            {
-                if((retVal = rtl8367c_getAsicReg(0x1d9d, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                if((regValue >> 8) & 1)
-                    break;
-            }
-
-            for (i=0; i<0xffff; i++);
-
-            if((retVal = rtl8367c_setAsicReg(0x133d, 0x2)) != RT_ERR_OK)
-                return retVal;
-
-            for (i=0; i<0xffff; i++);
-
-            if((retVal = rtl8367c_setAsicReg(0x6601, 0x0)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6602, 0x1401)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6600, 0xc1)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6601, 0x0)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6602, 0x1403)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6600, 0xc1)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicReg(0x133d, 0x0)) != RT_ERR_OK)
-                return retVal;
-
-            for (i=0; i<0xffff; i++);
-
-            if((retVal = rtl8367c_setAsicReg(0x1311, state)) != RT_ERR_OK)
-                return retVal;
-
-
-        }
-        else if (2== id)
-        {
-            if((retVal = rtl8367c_getAsicReg(0x13c4, &state)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicReg(0x13c4, 0x66)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicReg(0x13c4, 0x1066)) != RT_ERR_OK)
-                return retVal;
-
-            while(1)
-            {
-                if((retVal = rtl8367c_getAsicReg(0x1d9d, &regValue)) != RT_ERR_OK)
-                    return retVal;
-                if((regValue >> 9) & 1)
-                    break;
-            }
-
-            for (i=0; i<0xffff; i++);
-
-            if((retVal = rtl8367c_setAsicReg(0x133d, 0x2)) != RT_ERR_OK)
-                return retVal;
-
-            for (i=0; i<0xffff; i++);
-
-            if((retVal = rtl8367c_setAsicReg(0x6601, 0x0)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6602, 0x1401)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6600, 0xc0)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6601, 0x0)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6602, 0x1403)) != RT_ERR_OK)
-                return retVal;
-            if((retVal = rtl8367c_setAsicReg(0x6600, 0xc0)) != RT_ERR_OK)
-                return retVal;
-
-            if((retVal = rtl8367c_setAsicReg(0x133d, 0x0)) != RT_ERR_OK)
-                return retVal;
-
-            for (i=0; i<0xffff; i++);
-
-            if((retVal = rtl8367c_setAsicReg(0x13c4, state)) != RT_ERR_OK)
-                return retVal;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(option == 2)
-    {
-        if ((retVal = rtl8367c_getAsicSdsReg(0, 3, 0, &regValue))!=RT_ERR_OK)
-                  return retVal;
-              regValue |= 0x40;
-              if ((retVal = rtl8367c_setAsicSdsReg(0, 3, 0, regValue))!=RT_ERR_OK)
-                  return retVal;
-
-              for (i=0; i<0xffff; i++);
-
-              regValue &= ~(0x40);
-              if ((retVal = rtl8367c_setAsicSdsReg(0, 3, 0, regValue))!=RT_ERR_OK)
-                  return retVal;
-
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getSdsLinkStatus
- * Description:
- *      Get SGMII status
- * Input:
- *      id  - EXT ID
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *      None.
- */
-ret_t rtl8367c_getSdsLinkStatus(rtk_uint32 ext_id, rtk_uint32 *pSignalDetect, rtk_uint32 *pSync, rtk_uint32 *pLink)
-{
-    rtk_uint32 retVal, regValue, type, running = 0, retVal2;
-
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 0;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 1;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 2;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    if(type == 0)
-    {
-        if (1 == ext_id)
-        {
-            if ((retVal = rtl8367c_getAsicRegBit(0x130c, 5, &running))!=RT_ERR_OK)
-                return retVal;
-
-            if(running == 1)
-            {
-                if ((retVal = rtl8367c_setAsicRegBit(0x130c, 5, 0))!=RT_ERR_OK)
-                    return retVal;
-            }
-
-            retVal = rtl8367c_setAsicReg(0x6601, 0x003D);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6600, 0x0080);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_getAsicReg(0x6602, &regValue);
-
-            if(running == 1)
-            {
-                if ((retVal2 = rtl8367c_setAsicRegBit(0x130c, 5, 1))!=RT_ERR_OK)
-                    return retVal2;
-            }
-
-            if(retVal != RT_ERR_OK)
-                return retVal;
-
-            *pSignalDetect = (regValue & 0x0100) ? 1 : 0;
-            *pSync = (regValue & 0x0001) ? 1 : 0;
-            *pLink = (regValue & 0x0010) ? 1 : 0;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(type == 1)
-    {
-        if (1 == ext_id)
-        {
-            if ((retVal = rtl8367c_setAsicReg(0x6601, 0x003D))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6600, 0x0081))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_getAsicReg(0x6602, &regValue))!=RT_ERR_OK)
-                return retVal;
-
-            *pSignalDetect = (regValue & 0x0100) ? 1 : 0;
-            *pSync = (regValue & 0x0001) ? 1 : 0;
-            *pLink = (regValue & 0x0010) ? 1 : 0;
-        }
-        else if (2 == ext_id)
-        {
-            if ((retVal = rtl8367c_setAsicReg(0x6601, 0x003D))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6600, 0x0080))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_getAsicReg(0x6602, &regValue))!=RT_ERR_OK)
-                return retVal;
-
-            *pSignalDetect = (regValue & 0x0100) ? 1 : 0;
-            *pSync = (regValue & 0x0001) ? 1 : 0;
-            *pLink = (regValue & 0x0010) ? 1 : 0;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(type == 2)
-    {
-        if((retVal = rtl8367c_getAsicSdsReg(0, 30, 1, &regValue)) != RT_ERR_OK)
-            return retVal;
-        if((retVal = rtl8367c_getAsicSdsReg(0, 30, 1, &regValue)) != RT_ERR_OK)
-            return retVal;
-
-        *pSignalDetect = (regValue & 0x0100) ? 1 : 0;
-        *pSync = (regValue & 0x0001) ? 1 : 0;
-        *pLink = (regValue & 0x0010) ? 1 : 0;
-
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setSgmiiNway
- * Description:
- *      Set SGMII Nway
- * Input:
- *      ext_id      - EXT ID
- *      state       - SGMII Nway state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *      None.
- */
-ret_t rtl8367c_setSgmiiNway(rtk_uint32 ext_id, rtk_uint32 state)
-{
-    rtk_uint32 retVal, regValue, type, running = 0, retVal2;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 0;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 1;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 2;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    if(type == 0)
-    {
-        if (1 == ext_id)
-        {
-            if ((retVal = rtl8367c_getAsicRegBit(0x130c, 5, &running))!=RT_ERR_OK)
-                return retVal;
-
-            if(running == 1)
-            {
-                if ((retVal = rtl8367c_setAsicRegBit(0x130c, 5, 0))!=RT_ERR_OK)
-                    return retVal;
-            }
-
-            retVal = rtl8367c_setAsicReg(0x6601, 0x0002);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6600, 0x0080);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_getAsicReg(0x6602, &regValue);
-
-            if(retVal == RT_ERR_OK)
-            {
-                if(state)
-                      regValue |= 0x0200;
-                else
-                      regValue &= ~0x0200;
-
-                regValue |= 0x0100;
-            }
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6602, regValue);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6601, 0x0002);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6600, 0x00C0);
-
-            if(running == 1)
-            {
-                if ((retVal2 = rtl8367c_setAsicRegBit(0x130c, 5, 1))!=RT_ERR_OK)
-                    return retVal2;
-            }
-
-            if(retVal != RT_ERR_OK)
-                return retVal;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(type == 1)
-    {
-        if (1 == ext_id)
-        {
-            if ((retVal = rtl8367c_setAsicReg(0x6601, 0x0002))!=RT_ERR_OK)
-                   return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6600, 0x0081))!=RT_ERR_OK)
-                   return retVal;
-            if ((retVal = rtl8367c_getAsicReg(0x6602, &regValue))!=RT_ERR_OK)
-                   return retVal;
-
-            if(state)
-                  regValue |= 0x0200;
-            else
-                  regValue &= ~0x0200;
-
-            regValue |= 0x0100;
-
-            if ((retVal = rtl8367c_setAsicReg(0x6602, regValue))!=RT_ERR_OK)
-                   return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6601, 0x0002))!=RT_ERR_OK)
-                   return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6600, 0x00C1))!=RT_ERR_OK)
-                   return retVal;
-        }
-        else if (2 == ext_id)
-        {
-            if ((retVal = rtl8367c_setAsicReg(0x6601, 0x0002))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6600, 0x0080))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_getAsicReg(0x6602, &regValue))!=RT_ERR_OK)
-                return retVal;
-
-            if(state)
-                regValue |= 0x0200;
-            else
-                regValue &= ~0x0200;
-
-            regValue |= 0x0100;
-
-            if ((retVal = rtl8367c_setAsicReg(0x6602, regValue))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6601, 0x0002))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6600, 0x00C0))!=RT_ERR_OK)
-                return retVal;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(type == 2)
-    {
-        if ((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &regValue))!=RT_ERR_OK)
-            return retVal;
-
-        if(state & 1)
-            regValue &= ~0x100;
-        else
-            regValue |= 0x100;
-
-        if ((retVal = rtl8367c_setAsicSdsReg(0, 2, 0, regValue))!=RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getSgmiiNway
- * Description:
- *      Get SGMII Nway
- * Input:
- *      ext_id      - EXT ID
- *      state       - SGMII Nway state
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *      None.
- */
-ret_t rtl8367c_getSgmiiNway(rtk_uint32 ext_id, rtk_uint32 *pState)
-{
-    rtk_uint32 retVal, regValue, type, running = 0, retVal2;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 0;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 1;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 2;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    if(type == 0)
-    {
-        if (1 == ext_id)
-        {
-            if ((retVal = rtl8367c_getAsicRegBit(0x130c, 5, &running))!=RT_ERR_OK)
-                return retVal;
-
-            if(running == 1)
-            {
-                if ((retVal = rtl8367c_setAsicRegBit(0x130c, 5, 0))!=RT_ERR_OK)
-                    return retVal;
-            }
-
-            retVal = rtl8367c_setAsicReg(0x6601, 0x0002);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_setAsicReg(0x6600, 0x0080);
-
-            if(retVal == RT_ERR_OK)
-                retVal = rtl8367c_getAsicReg(0x6602, &regValue);
-
-            if(running == 1)
-            {
-                if ((retVal2 = rtl8367c_setAsicRegBit(0x130c, 5, 1))!=RT_ERR_OK)
-                    return retVal2;
-            }
-
-            if(retVal != RT_ERR_OK)
-                return retVal;
-
-            if(regValue & 0x0200)
-                *pState = 1;
-            else
-                *pState = 0;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(type == 1)
-    {
-        if (1 == ext_id)
-        {
-                if ((retVal = rtl8367c_setAsicReg(0x6601, 0x0002))!=RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_setAsicReg(0x6600, 0x0081))!=RT_ERR_OK)
-                    return retVal;
-                if ((retVal = rtl8367c_getAsicReg(0x6602, &regValue))!=RT_ERR_OK)
-                    return retVal;
-
-                if(regValue & 0x0200)
-                    *pState = 1;
-                else
-                    *pState = 0;
-        }
-        else if (2 == ext_id)
-        {
-            if ((retVal = rtl8367c_setAsicReg(0x6601, 0x0002))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_setAsicReg(0x6600, 0x0080))!=RT_ERR_OK)
-                return retVal;
-            if ((retVal = rtl8367c_getAsicReg(0x6602, &regValue))!=RT_ERR_OK)
-                return retVal;
-
-            if(regValue & 0x0200)
-                *pState = 1;
-            else
-                *pState = 0;
-        }
-        else
-            return RT_ERR_PORT_ID;
-    }
-    else if(type == 2)
-    {
-        if ((retVal = rtl8367c_getAsicSdsReg(0, 2, 0, &regValue))!=RT_ERR_OK)
-            return retVal;
-
-        if(regValue & 0x100)
-            *pState = 0;
-        else
-            *pState = 1;
-    }
-
-    return RT_ERR_OK;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_portIsolation.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_portIsolation.c
deleted file mode 100644
index e0b9db4bfb..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_portIsolation.c
+++ /dev/null
@@ -1,119 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port isolation related functions
- *
- */
-
-#include <rtl8367c_asicdrv_portIsolation.h>
-/* Function Name:
- *      rtl8367c_setAsicPortIsolationPermittedPortmask
- * Description:
- *      Set permitted port isolation portmask
- * Input:
- *      port            - Physical port number (0~10)
- *      permitPortmask  - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortIsolationPermittedPortmask(rtk_uint32 port, rtk_uint32 permitPortmask)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if( permitPortmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicReg(RTL8367C_PORT_ISOLATION_PORT_MASK_REG(port), permitPortmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortIsolationPermittedPortmask
- * Description:
- *      Get permitted port isolation portmask
- * Input:
- *      port                - Physical port number (0~10)
- *      pPermitPortmask     - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortIsolationPermittedPortmask(rtk_uint32 port, rtk_uint32 *pPermitPortmask)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicReg(RTL8367C_PORT_ISOLATION_PORT_MASK_REG(port), pPermitPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortIsolationEfid
- * Description:
- *      Set port isolation EFID
- * Input:
- *      port    - Physical port number (0~10)
- *      efid    - EFID (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - Input parameter out of range
- * Note:
- *      EFID is used in individual learning in filtering database
- */
-ret_t rtl8367c_setAsicPortIsolationEfid(rtk_uint32 port, rtk_uint32 efid)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if( efid > RTL8367C_EFIDMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_PORT_EFID_REG(port), RTL8367C_PORT_EFID_MASK(port), efid);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortIsolationEfid
- * Description:
- *      Get port isolation EFID
- * Input:
- *      port    - Physical port number (0~10)
- *      pEfid   - EFID (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortIsolationEfid(rtk_uint32 port, rtk_uint32 *pEfid)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_PORT_EFID_REG(port), RTL8367C_PORT_EFID_MASK(port), pEfid);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_qos.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_qos.c
deleted file mode 100644
index 89c3c3e02e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_qos.c
+++ /dev/null
@@ -1,778 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Qos related functions
- *
- */
-
-#include <rtl8367c_asicdrv_qos.h>
-/* Function Name:
- *      rtl8367c_setAsicPriorityDot1qRemapping
- * Description:
- *      Set 802.1Q absolutely priority
- * Input:
- *      srcpriority - Priority value
- *      priority     - Absolute priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY    - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPriorityDot1qRemapping(rtk_uint32 srcpriority, rtk_uint32 priority )
-{
-    if((srcpriority > RTL8367C_PRIMAX) || (priority > RTL8367C_PRIMAX))
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_1Q_PRIORITY_REMAPPING_REG(srcpriority), RTL8367C_QOS_1Q_PRIORITY_REMAPPING_MASK(srcpriority),priority);
-}
-/* Function Name:
- *      rtl8367c_getAsicPriorityDot1qRemapping
- * Description:
- *      Get 802.1Q absolutely priority
- * Input:
- *      srcpriority - Priority value
- *      pPriority     - Absolute priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPriorityDot1qRemapping(rtk_uint32 srcpriority, rtk_uint32 *pPriority )
-{
-    if(srcpriority > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_1Q_PRIORITY_REMAPPING_REG(srcpriority), RTL8367C_QOS_1Q_PRIORITY_REMAPPING_MASK(srcpriority), pPriority);
-}
-/* Function Name:
- *      rtl8367c_setAsicPriorityPortBased
- * Description:
- *      Set port based priority
- * Input:
- *      port         - Physical port number (0~7)
- *      priority     - Priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_QOS_INT_PRIORITY    - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPriorityPortBased(rtk_uint32 port, rtk_uint32 priority )
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(priority > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_QOS_PORTBASED_PRIORITY_REG(port), RTL8367C_QOS_PORTBASED_PRIORITY_MASK(port), priority);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_QOS_PORTBASED_PRIORITY_CTRL2, 0x7 << ((port - 8) << 2), priority);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicPriorityPortBased
- * Description:
- *      Get port based priority
- * Input:
- *      port         - Physical port number (0~7)
- *      pPriority     - Priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPriorityPortBased(rtk_uint32 port, rtk_uint32 *pPriority )
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_QOS_PORTBASED_PRIORITY_REG(port), RTL8367C_QOS_PORTBASED_PRIORITY_MASK(port), pPriority);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_QOS_PORTBASED_PRIORITY_CTRL2, 0x7 << ((port - 8) << 2), pPriority);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicPriorityDscpBased
- * Description:
- *      Set DSCP-based priority
- * Input:
- *      dscp         - DSCP value
- *      priority     - Priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_DSCP_VALUE    - Invalid DSCP value
- *      RT_ERR_QOS_INT_PRIORITY    - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPriorityDscpBased(rtk_uint32 dscp, rtk_uint32 priority )
-{
-    if(priority > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if(dscp > RTL8367C_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_DSCP_TO_PRIORITY_REG(dscp), RTL8367C_QOS_DSCP_TO_PRIORITY_MASK(dscp), priority);
-}
-/* Function Name:
- *      rtl8367c_getAsicPriorityDscpBased
- * Description:
- *      Get DSCP-based priority
- * Input:
- *      dscp         - DSCP value
- *      pPriority     - Priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY    - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPriorityDscpBased(rtk_uint32 dscp, rtk_uint32 *pPriority )
-{
-    if(dscp > RTL8367C_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_DSCP_TO_PRIORITY_REG(dscp), RTL8367C_QOS_DSCP_TO_PRIORITY_MASK(dscp), pPriority);
-}
-/* Function Name:
- *      rtl8367c_setAsicPriorityDecision
- * Description:
- *      Set priority decision table
- * Input:
- *      prisrc         - Priority decision source
- *      decisionPri - Decision priority assignment
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                     - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY        - Invalid priority
- *      RT_ERR_QOS_SEL_PRI_SOURCE    - Invalid priority decision source parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPriorityDecision(rtk_uint32 index, rtk_uint32 prisrc, rtk_uint32 decisionPri)
-{
-    ret_t retVal;
-
-    if(index >= PRIDEC_IDX_END )
-        return RT_ERR_ENTRY_INDEX;
-
-    if(prisrc >= PRIDEC_END )
-        return RT_ERR_QOS_SEL_PRI_SOURCE;
-
-    if(decisionPri > RTL8367C_DECISIONPRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    switch(index)
-    {
-        case PRIDEC_IDX0:
-            if((retVal = rtl8367c_setAsicRegBits(RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_REG(prisrc), RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_MASK(prisrc), decisionPri))!=  RT_ERR_OK)
-                return retVal;
-            break;
-        case PRIDEC_IDX1:
-            if((retVal = rtl8367c_setAsicRegBits(RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_REG(prisrc), RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_MASK(prisrc), decisionPri))!=  RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    };
-
-    return RT_ERR_OK;
-
-
-}
-
-/* Function Name:
- *      rtl8367c_getAsicPriorityDecision
- * Description:
- *      Get priority decision table
- * Input:
- *      prisrc         - Priority decision source
- *      pDecisionPri - Decision priority assignment
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                     - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_QOS_SEL_PRI_SOURCE    - Invalid priority decision source parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPriorityDecision(rtk_uint32 index, rtk_uint32 prisrc, rtk_uint32* pDecisionPri)
-{
-    ret_t retVal;
-
-    if(index >= PRIDEC_IDX_END )
-        return RT_ERR_ENTRY_INDEX;
-
-    if(prisrc >= PRIDEC_END )
-        return RT_ERR_QOS_SEL_PRI_SOURCE;
-
-    switch(index)
-    {
-        case PRIDEC_IDX0:
-            if((retVal = rtl8367c_getAsicRegBits(RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_REG(prisrc), RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_MASK(prisrc), pDecisionPri))!=  RT_ERR_OK)
-                return retVal;
-            break;
-        case PRIDEC_IDX1:
-            if((retVal = rtl8367c_getAsicRegBits(RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_REG(prisrc), RTL8367C_QOS_INTERNAL_PRIORITY_DECISION2_MASK(prisrc), pDecisionPri))!=  RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    };
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtl8367c_setAsicPortPriorityDecisionIndex
- * Description:
- *      Set priority decision index for each port
- * Input:
- *      port     - Physical port number (0~7)
- *      index     - Table index
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK             - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_QUEUE_NUM      - Invalid queue number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortPriorityDecisionIndex(rtk_uint32 port, rtk_uint32 index )
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(index >= PRIDEC_IDX_END)
-        return RT_ERR_ENTRY_INDEX;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_IDX_CTRL, port, index);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortPriorityDecisionIndex
- * Description:
- *      Get priority decision index  for each port
- * Input:
- *      port     - Physical port number (0~7)
- *      pIndex     - Table index
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK             - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortPriorityDecisionIndex(rtk_uint32 port, rtk_uint32 *pIndex )
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_QOS_INTERNAL_PRIORITY_DECISION_IDX_CTRL, port, pIndex);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicOutputQueueMappingIndex
- * Description:
- *      Set output queue number for each port
- * Input:
- *      port     - Physical port number (0~7)
- *      index     - Mapping table index
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK             - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_QUEUE_NUM      - Invalid queue number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicOutputQueueMappingIndex(rtk_uint32 port, rtk_uint32 index )
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(index >= RTL8367C_QUEUENO)
-        return RT_ERR_QUEUE_NUM;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_PORT_QUEUE_NUMBER_REG(port), RTL8367C_QOS_PORT_QUEUE_NUMBER_MASK(port), index);
-}
-/* Function Name:
- *      rtl8367c_getAsicOutputQueueMappingIndex
- * Description:
- *      Get output queue number for each port
- * Input:
- *      port     - Physical port number (0~7)
- *      pIndex     - Mapping table index
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK             - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicOutputQueueMappingIndex(rtk_uint32 port, rtk_uint32 *pIndex )
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_PORT_QUEUE_NUMBER_REG(port), RTL8367C_QOS_PORT_QUEUE_NUMBER_MASK(port), pIndex);
-}
-/* Function Name:
- *      rtl8367c_setAsicPriorityToQIDMappingTable
- * Description:
- *      Set priority to QID mapping table parameters
- * Input:
- *      index         - Mapping table index
- *      priority     - The priority value
- *      qid         - Queue id
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QUEUE_ID          - Invalid queue id
- *      RT_ERR_QUEUE_NUM          - Invalid queue number
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPriorityToQIDMappingTable(rtk_uint32 index, rtk_uint32 priority, rtk_uint32 qid )
-{
-    if(index >= RTL8367C_QUEUENO)
-        return RT_ERR_QUEUE_NUM;
-
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_1Q_PRIORITY_TO_QID_REG(index, priority), RTL8367C_QOS_1Q_PRIORITY_TO_QID_MASK(priority), qid);
-}
-/* Function Name:
- *      rtl8367c_getAsicPriorityToQIDMappingTable
- * Description:
- *      Get priority to QID mapping table parameters
- * Input:
- *      index         - Mapping table index
- *      priority     - The priority value
- *      pQid         - Queue id
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QUEUE_NUM          - Invalid queue number
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPriorityToQIDMappingTable(rtk_uint32 index, rtk_uint32 priority, rtk_uint32* pQid)
-{
-    if(index >= RTL8367C_QUEUENO)
-        return RT_ERR_QUEUE_NUM;
-
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_1Q_PRIORITY_TO_QID_REG(index, priority), RTL8367C_QOS_1Q_PRIORITY_TO_QID_MASK(priority), pQid);
-}
-/* Function Name:
- *      rtl8367c_setAsicRemarkingDot1pAbility
- * Description:
- *      Set 802.1p remarking ability
- * Input:
- *      port     - Physical port number (0~7)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK             - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRemarkingDot1pAbility(rtk_uint32 port, rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_PORT_MISC_CFG_REG(port), RTL8367C_1QREMARK_ENABLE_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicRemarkingDot1pAbility
- * Description:
- *      Get 802.1p remarking ability
- * Input:
- *      port     - Physical port number (0~7)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRemarkingDot1pAbility(rtk_uint32 port, rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_PORT_MISC_CFG_REG(port), RTL8367C_1QREMARK_ENABLE_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicRemarkingDot1pParameter
- * Description:
- *      Set 802.1p remarking parameter
- * Input:
- *      priority     - Priority value
- *      newPriority - New priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRemarkingDot1pParameter(rtk_uint32 priority, rtk_uint32 newPriority )
-{
-    if(priority > RTL8367C_PRIMAX || newPriority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_1Q_REMARK_REG(priority), RTL8367C_QOS_1Q_REMARK_MASK(priority), newPriority);
-}
-/* Function Name:
- *      rtl8367c_getAsicRemarkingDot1pParameter
- * Description:
- *      Get 802.1p remarking parameter
- * Input:
- *      priority     - Priority value
- *      pNewPriority - New priority value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRemarkingDot1pParameter(rtk_uint32 priority, rtk_uint32 *pNewPriority )
-{
-    if(priority > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_1Q_REMARK_REG(priority), RTL8367C_QOS_1Q_REMARK_MASK(priority), pNewPriority);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRemarkingDot1pSrc
- * Description:
- *      Set remarking source of 802.1p remarking.
- * Input:
- *      type      - remarking source
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID  - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
-
- * Note:
- *      The API can configure 802.1p remark functionality to map original DSCP value or internal
- *      priority to TX DSCP value.
- */
-ret_t rtl8367c_setAsicRemarkingDot1pSrc(rtk_uint32 type)
-{
-
-    if(type >= DOT1P_PRISEL_END )
-        return RT_ERR_QOS_SEL_PRI_SOURCE;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_RMK_CFG_SEL_CTRL, RTL8367C_RMK_1Q_CFG_SEL_OFFSET, type);
-}
-
-
-/* Function Name:
- *      rtl8367c_getAsicRemarkingDot1pSrc
- * Description:
- *      Get remarking source of 802.1p remarking.
- * Output:
- *      pType      - remarking source
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
- *      RT_ERR_NULL_POINTER     - input parameter may be null pointer
-
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRemarkingDot1pSrc(rtk_uint32 *pType)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_RMK_CFG_SEL_CTRL, RTL8367C_RMK_1Q_CFG_SEL_OFFSET, pType);
-}
-
-
-
-
-
-/* Function Name:
- *      rtl8367c_setAsicRemarkingDscpAbility
- * Description:
- *      Set DSCP remarking ability
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRemarkingDscpAbility(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REMARKING_CTRL_REG, RTL8367C_REMARKING_DSCP_ENABLE_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicRemarkingDscpAbility
- * Description:
- *      Get DSCP remarking ability
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK     - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRemarkingDscpAbility(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REMARKING_CTRL_REG, RTL8367C_REMARKING_DSCP_ENABLE_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicRemarkingDscpParameter
- * Description:
- *      Set DSCP remarking parameter
- * Input:
- *      priority     - Priority value
- *      newDscp     - New DSCP value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_DSCP_VALUE    - Invalid DSCP value
- *      RT_ERR_QOS_INT_PRIORITY    - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRemarkingDscpParameter(rtk_uint32 priority, rtk_uint32 newDscp )
-{
-    if(priority > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    if(newDscp > RTL8367C_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_DSCP_REMARK_REG(priority), RTL8367C_QOS_DSCP_REMARK_MASK(priority), newDscp);
-}
-/* Function Name:
- *      rtl8367c_getAsicRemarkingDscpParameter
- * Description:
- *      Get DSCP remarking parameter
- * Input:
- *      priority     - Priority value
- *      pNewDscp     - New DSCP value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                 - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY    - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRemarkingDscpParameter(rtk_uint32 priority, rtk_uint32* pNewDscp )
-{
-    if(priority > RTL8367C_PRIMAX )
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_DSCP_REMARK_REG(priority), RTL8367C_QOS_DSCP_REMARK_MASK(priority), pNewDscp);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRemarkingDscpSrc
- * Description:
- *      Set remarking source of DSCP remarking.
- * Input:
- *      type      - remarking source
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID  - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
-
- * Note:
- *      The API can configure DSCP remark functionality to map original DSCP value or internal
- *      priority to TX DSCP value.
- */
-ret_t rtl8367c_setAsicRemarkingDscpSrc(rtk_uint32 type)
-{
-
-    if(type >= DSCP_PRISEL_END )
-        return RT_ERR_QOS_SEL_PRI_SOURCE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_RMK_CFG_SEL_CTRL, RTL8367C_RMK_DSCP_CFG_SEL_MASK, type);
-}
-
-
-/* Function Name:
- *      rtl8367c_getAsicRemarkingDscpSrc
- * Description:
- *      Get remarking source of DSCP remarking.
- * Output:
- *      pType      - remarking source
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT         - The module is not initial
- *      RT_ERR_PORT_ID          - invalid port id
- *      RT_ERR_INPUT            - invalid input parameter
- *      RT_ERR_NULL_POINTER     - input parameter may be null pointer
-
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRemarkingDscpSrc(rtk_uint32 *pType)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_RMK_CFG_SEL_CTRL, RTL8367C_RMK_DSCP_CFG_SEL_MASK, pType);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRemarkingDscp2Dscp
- * Description:
- *      Set DSCP to remarked DSCP mapping.
- * Input:
- *      dscp    - DSCP value
- *      rmkDscp - remarked DSCP value
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID          - Invalid unit id
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid dscp value
- * Note:
- *      dscp parameter can be DSCP value or internal priority according to configuration of API
- *      dal_apollomp_qos_dscpRemarkSrcSel_set(), because DSCP remark functionality can map original DSCP
- *      value or internal priority to TX DSCP value.
- */
-ret_t rtl8367c_setAsicRemarkingDscp2Dscp(rtk_uint32 dscp, rtk_uint32 rmkDscp)
-{
-    if((dscp > RTL8367C_DSCPMAX ) || (rmkDscp > RTL8367C_DSCPMAX))
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_DSCP_TO_DSCP_REG(dscp), RTL8367C_QOS_DSCP_TO_DSCP_MASK(dscp), rmkDscp);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicRemarkingDscp2Dscp
- * Description:
- *      Get DSCP to remarked DSCP mapping.
- * Input:
- *      dscp    - DSCP value
- * Output:
- *      pRmkDscp   - remarked DSCP value
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_QOS_DSCP_VALUE   - Invalid dscp value
- *      RT_ERR_NULL_POINTER     - NULL pointer
- * Note:
- *      None.
- */
-ret_t rtl8367c_getAsicRemarkingDscp2Dscp(rtk_uint32 dscp, rtk_uint32 *pRmkDscp)
-{
-    if(dscp > RTL8367C_DSCPMAX)
-        return RT_ERR_QOS_DSCP_VALUE;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_DSCP_TO_DSCP_REG(dscp), RTL8367C_QOS_DSCP_TO_DSCP_MASK(dscp), pRmkDscp);
-
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_rldp.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_rldp.c
deleted file mode 100644
index 0309689d39..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_rldp.c
+++ /dev/null
@@ -1,674 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 42321 $
- * $Date: 2013-08-26 13:51:29 +0800 (週一, 26 八月 2013) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : RLDP related functions
- *
- */
-
-#include <rtl8367c_asicdrv_rldp.h>
-/* Function Name:
- *      rtl8367c_setAsicRldp
- * Description:
- *      Set RLDP function enable/disable
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldp(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_ENABLE_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldp
- * Description:
- *      Get RLDP function enable/disable
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldp(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_ENABLE_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpEnable8051
- * Description:
- *      Set RLDP function handled by ASIC or 8051
- * Input:
- *      enabled     - 1: enabled 8051, 0: disabled 8051 (RLDP is handled by ASIC)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpEnable8051(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_8051_ENABLE_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldrtl8367c_getAsicRldpEnable8051pEnable8051
- * Description:
- *      Get RLDP function handled by ASIC or 8051
- * Input:
- *      pEnabled    - 1: enabled 8051, 0: disabled 8051 (RLDP is handled by ASIC)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpEnable8051(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_8051_ENABLE_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpCompareRandomNumber
- * Description:
- *      Set enable compare the random number field and seed field of RLDP frame
- * Input:
- *      enabled     - 1: enabled comparing random number, 0: disabled comparing random number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpCompareRandomNumber(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_COMP_ID_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpCompareRandomNumber
- * Description:
- *      Get enable compare the random number field and seed field of RLDP frame
- * Input:
- *      pEnabled    - 1: enabled comparing random number, 0: disabled comparing random number
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpCompareRandomNumber(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_COMP_ID_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpIndicatorSource
- * Description:
- *      Set buzzer and LED source when detecting a loop
- * Input:
- *      src     - 0: ASIC, 1: 8051
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpIndicatorSource(rtk_uint32 src)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_INDICATOR_SOURCE_OFFSET, src);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpIndicatorSource
- * Description:
- *      Get buzzer and LED source when detecting a loop
- * Input:
- *      pSrc    - 0: ASIC, 1: 8051
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpIndicatorSource(rtk_uint32 *pSrc)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_INDICATOR_SOURCE_OFFSET, pSrc);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpCheckingStatePara
- * Description:
- *      Set retry count and retry period of checking state
- * Input:
- *      retryCount  - 0~0xFF (times)
- *      retryPeriod - 0~0xFFFF (ms)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpCheckingStatePara(rtk_uint32 retryCount, rtk_uint32 retryPeriod)
-{
-    ret_t retVal;
-
-    if(retryCount > 0xFF)
-        return RT_ERR_OUT_OF_RANGE;
-    if(retryPeriod > RTL8367C_REGDATAMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_RLDP_RETRY_COUNT_REG, RTL8367C_RLDP_RETRY_COUNT_CHKSTATE_MASK, retryCount);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicReg(RTL8367C_RLDP_RETRY_PERIOD_CHKSTATE_REG, retryPeriod);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpCheckingStatePara
- * Description:
- *      Get retry count and retry period of checking state
- * Input:
- *      pRetryCount     - 0~0xFF (times)
- *      pRetryPeriod    - 0~0xFFFF (ms)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpCheckingStatePara(rtk_uint32 *pRetryCount, rtk_uint32 *pRetryPeriod)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_RLDP_RETRY_COUNT_REG, RTL8367C_RLDP_RETRY_COUNT_CHKSTATE_MASK, pRetryCount);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_getAsicReg(RTL8367C_RLDP_RETRY_PERIOD_CHKSTATE_REG, pRetryPeriod);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpLoopStatePara
- * Description:
- *      Set retry count and retry period of loop state
- * Input:
- *      retryCount  - 0~0xFF (times)
- *      retryPeriod - 0~0xFFFF (ms)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpLoopStatePara(rtk_uint32 retryCount, rtk_uint32 retryPeriod)
-{
-    ret_t retVal;
-
-    if(retryCount > 0xFF)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(retryPeriod > RTL8367C_REGDATAMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_RLDP_RETRY_COUNT_REG, RTL8367C_RLDP_RETRY_COUNT_LOOPSTATE_MASK, retryCount);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicReg(RTL8367C_RLDP_RETRY_PERIOD_LOOPSTATE_REG, retryPeriod);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpLoopStatePara
- * Description:
- *      Get retry count and retry period of loop state
- * Input:
- *      pRetryCount     - 0~0xFF (times)
- *      pRetryPeriod    - 0~0xFFFF (ms)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - input parameter out of range
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpLoopStatePara(rtk_uint32 *pRetryCount, rtk_uint32 *pRetryPeriod)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_RLDP_RETRY_COUNT_REG, RTL8367C_RLDP_RETRY_COUNT_LOOPSTATE_MASK, pRetryCount);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_getAsicReg(RTL8367C_RLDP_RETRY_PERIOD_LOOPSTATE_REG, pRetryPeriod);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpTxPortmask
- * Description:
- *      Set portmask that send/forward RLDP frame
- * Input:
- *      portmask    - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpTxPortmask(rtk_uint32 portmask)
-{
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicReg(RTL8367C_RLDP_TX_PMSK_REG, portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpTxPortmask
- * Description:
- *      Get portmask that send/forward RLDP frame
- * Input:
- *      pPortmask   - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpTxPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_RLDP_TX_PMSK_REG, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpMagicNum
- * Description:
- *      Set Random seed of RLDP
- * Input:
- *      seed    - MAC
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpMagicNum(ether_addr_t seed)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-
-    accessPtr = (rtk_uint16*)&seed;
-
-    for (i = 0; i < 3; i++)
-    {
-        regData = *accessPtr;
-        retVal = rtl8367c_setAsicReg(RTL8367C_RLDP_MAGIC_NUM_REG_BASE + i, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        accessPtr++;
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpMagicNum
- * Description:
- *      Get Random seed of RLDP
- * Input:
- *      pSeed   - MAC
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpMagicNum(ether_addr_t *pSeed)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-
-    accessPtr = (rtk_uint16*)pSeed;
-
-    for(i = 0; i < 3; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_RLDP_MAGIC_NUM_REG_BASE + i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *accessPtr = regData;
-        accessPtr++;
-    }
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicRldpLoopedPortmask
- * Description:
- *      Get looped portmask
- * Input:
- *      pPortmask   - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpLoopedPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_RLDP_LOOP_PMSK_REG, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpRandomNumber
- * Description:
- *      Get Random number of RLDP
- * Input:
- *      pRandNumber     - MAC
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpRandomNumber(ether_addr_t *pRandNumber)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_int16 accessPtr[3];
-    rtk_uint32 i;
-
-    for(i = 0; i < 3; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_RLDP_RAND_NUM_REG_BASE+ i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        accessPtr[i] = regData;
-    }
-
-    memcpy(pRandNumber, accessPtr, 6);
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpLoopedPortmask
- * Description:
- *      Get port number of looped pair
- * Input:
- *      port        - Physical port number (0~7)
- *      pLoopedPair     - port (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpLoopedPortPair(rtk_uint32 port, rtk_uint32 *pLoopedPair)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_RLDP_LOOP_PORT_REG(port), RTL8367C_RLDP_LOOP_PORT_MASK(port), pLoopedPair);
-    else
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_RLDP_LOOP_PORT_REG4 + ((port - 8) >> 1), RTL8367C_RLDP_LOOP_PORT_MASK(port), pLoopedPair);
-}
-/* Function Name:
- *      rtl8367c_setAsicRlppTrap8051
- * Description:
- *      Set trap RLPP packet to 8051
- * Input:
- *      enabled     - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRlppTrap8051(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLPP_8051_TRAP_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicRlppTrap8051
- * Description:
- *      Get trap RLPP packet to 8051
- * Input:
- *      pEnabled    - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRlppTrap8051(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLPP_8051_TRAP_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpLeaveLoopedPortmask
- * Description:
- *      Clear leaved looped portmask
- * Input:
- *      portmask    - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpLeaveLoopedPortmask(rtk_uint32 portmask)
-{
-    return rtl8367c_setAsicReg(RTL8367C_REG_RLDP_RELEASED_INDICATOR, portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpLeaveLoopedPortmask
- * Description:
- *      Get leaved looped portmask
- * Input:
- *      pPortmask   - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpLeaveLoopedPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_RLDP_RELEASED_INDICATOR, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicRldpEnterLoopedPortmask
- * Description:
- *      Clear enter loop portmask
- * Input:
- *      portmask    - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpEnterLoopedPortmask(rtk_uint32 portmask)
-{
-    return rtl8367c_setAsicReg(RTL8367C_REG_RLDP_LOOPED_INDICATOR, portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpEnterLoopedPortmask
- * Description:
- *      Get enter loop portmask
- * Input:
- *      pPortmask   - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpEnterLoopedPortmask(rtk_uint32 *pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_RLDP_LOOPED_INDICATOR, pPortmask);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRldpTriggerMode
- * Description:
- *      Set trigger RLDP mode
- * Input:
- *      mode    - 1: Periodically, 0: SA moving
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldpTriggerMode(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_TRIGGER_MODE_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicRldpTriggerMode
- * Description:
- *      Get trigger RLDP mode
- * Input:
- *      pMode   - - 1: Periodically, 0: SA moving
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldpTriggerMode(rtk_uint32 *pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_RLDP_CTRL0, RTL8367C_RLDP_TRIGGER_MODE_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRldp8051Portmask
- * Description:
- *      Set 8051/CPU configured looped portmask
- * Input:
- *      portmask    - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRldp8051Portmask(rtk_uint32 portmask)
-{
-    ret_t retVal;
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_RLDP_CTRL0_REG,RTL8367C_RLDP_8051_LOOP_PORTMSK_MASK,portmask & 0xff);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_RLDP_CTRL5,RTL8367C_RLDP_CTRL5_MASK,(portmask >> 8) & 7);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicRldp8051Portmask
- * Description:
- *      Get 8051/CPU configured looped portmask
- * Input:
- *      pPortmask   - 0~0xFF
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRldp8051Portmask(rtk_uint32 *pPortmask)
-{
-    rtk_uint32 tmpPmsk;
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_RLDP_CTRL0_REG,RTL8367C_RLDP_8051_LOOP_PORTMSK_MASK,&tmpPmsk);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask = tmpPmsk & 0xff;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_RLDP_CTRL5,RTL8367C_RLDP_CTRL5_MASK,&tmpPmsk);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask |= (tmpPmsk & 7) <<8;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_rma.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_rma.c
deleted file mode 100644
index f297defa78..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_rma.c
+++ /dev/null
@@ -1,362 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 64716 $
- * $Date: 2015-12-31 16:31:55 +0800 (週四, 31 �二月 2015) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : RMA related functions
- *
- */
-
-#include <rtl8367c_asicdrv_rma.h>
-/* Function Name:
- *      rtl8367c_setAsicRma
- * Description:
- *      Set reserved multicast address for CPU trapping
- * Input:
- *      index     - reserved multicast LSB byte, 0x00~0x2F is available value
- *      pRmacfg     - type of RMA for trapping frame type setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRma(rtk_uint32 index, rtl8367c_rma_t* pRmacfg)
-{
-    rtk_uint32 regData = 0;
-    ret_t retVal;
-
-    if(index > RTL8367C_RMAMAX)
-        return RT_ERR_RMA_ADDR;
-
-    regData |= (pRmacfg->portiso_leaky & 0x0001);
-    regData |= ((pRmacfg->vlan_leaky & 0x0001) << 1);
-    regData |= ((pRmacfg->keep_format & 0x0001) << 2);
-    regData |= ((pRmacfg->trap_priority & 0x0007) << 3);
-    regData |= ((pRmacfg->discard_storm_filter & 0x0001) << 6);
-    regData |= ((pRmacfg->operation & 0x0003) << 7);
-
-    if( (index >= 0x4 && index <= 0x7) || (index >= 0x9 && index <= 0x0C) || (0x0F == index))
-        index = 0x04;
-    else if((index >= 0x13 && index <= 0x17) || (0x19 == index) || (index >= 0x1B && index <= 0x1f))
-        index = 0x13;
-    else if(index >= 0x22 && index <= 0x2F)
-        index = 0x22;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, pRmacfg->trap_priority);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicReg(RTL8367C_REG_RMA_CTRL00+index, regData);
-}
-/* Function Name:
- *      rtl8367c_getAsicRma
- * Description:
- *      Get reserved multicast address for CPU trapping
- * Input:
- *      index     - reserved multicast LSB byte, 0x00~0x2F is available value
- *      rmacfg     - type of RMA for trapping frame type setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRma(rtk_uint32 index, rtl8367c_rma_t* pRmacfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    if(index > RTL8367C_RMAMAX)
-        return RT_ERR_RMA_ADDR;
-
-    if( (index >= 0x4 && index <= 0x7) || (index >= 0x9 && index <= 0x0C) || (0x0F == index))
-        index = 0x04;
-    else if((index >= 0x13 && index <= 0x17) || (0x19 == index) || (index >= 0x1B && index <= 0x1f))
-        index = 0x13;
-    else if(index >= 0x22 && index <= 0x2F)
-        index = 0x22;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_RMA_CTRL00+index, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->operation = ((regData >> 7) & 0x0003);
-    pRmacfg->discard_storm_filter = ((regData >> 6) & 0x0001);
-    pRmacfg->trap_priority = ((regData >> 3) & 0x0007);
-    pRmacfg->keep_format = ((regData >> 2) & 0x0001);
-    pRmacfg->vlan_leaky = ((regData >> 1) & 0x0001);
-    pRmacfg->portiso_leaky = (regData & 0x0001);
-
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->trap_priority = regData;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRmaCdp
- * Description:
- *      Set CDP(Cisco Discovery Protocol) for CPU trapping
- * Input:
- *      pRmacfg     - type of RMA for trapping frame type setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRmaCdp(rtl8367c_rma_t* pRmacfg)
-{
-    rtk_uint32 regData = 0;
-    ret_t retVal;
-
-    if(pRmacfg->operation >= RMAOP_END)
-        return RT_ERR_RMA_ACTION;
-
-    if(pRmacfg->trap_priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    regData |= (pRmacfg->portiso_leaky & 0x0001);
-    regData |= ((pRmacfg->vlan_leaky & 0x0001) << 1);
-    regData |= ((pRmacfg->keep_format & 0x0001) << 2);
-    regData |= ((pRmacfg->trap_priority & 0x0007) << 3);
-    regData |= ((pRmacfg->discard_storm_filter & 0x0001) << 6);
-    regData |= ((pRmacfg->operation & 0x0003) << 7);
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, pRmacfg->trap_priority);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicReg(RTL8367C_REG_RMA_CTRL_CDP, regData);
-}
-/* Function Name:
- *      rtl8367c_getAsicRmaCdp
- * Description:
- *      Get CDP(Cisco Discovery Protocol) for CPU trapping
- * Input:
- *      None
- * Output:
- *      pRmacfg     - type of RMA for trapping frame type setting
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRmaCdp(rtl8367c_rma_t* pRmacfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_RMA_CTRL_CDP, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->operation = ((regData >> 7) & 0x0003);
-    pRmacfg->discard_storm_filter = ((regData >> 6) & 0x0001);
-    pRmacfg->trap_priority = ((regData >> 3) & 0x0007);
-    pRmacfg->keep_format = ((regData >> 2) & 0x0001);
-    pRmacfg->vlan_leaky = ((regData >> 1) & 0x0001);
-    pRmacfg->portiso_leaky = (regData & 0x0001);
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->trap_priority = regData;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRmaCsstp
- * Description:
- *      Set CSSTP(Cisco Shared Spanning Tree Protocol) for CPU trapping
- * Input:
- *      pRmacfg     - type of RMA for trapping frame type setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRmaCsstp(rtl8367c_rma_t* pRmacfg)
-{
-    rtk_uint32 regData = 0;
-    ret_t retVal;
-
-    if(pRmacfg->operation >= RMAOP_END)
-        return RT_ERR_RMA_ACTION;
-
-    if(pRmacfg->trap_priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    regData |= (pRmacfg->portiso_leaky & 0x0001);
-    regData |= ((pRmacfg->vlan_leaky & 0x0001) << 1);
-    regData |= ((pRmacfg->keep_format & 0x0001) << 2);
-    regData |= ((pRmacfg->trap_priority & 0x0007) << 3);
-    regData |= ((pRmacfg->discard_storm_filter & 0x0001) << 6);
-    regData |= ((pRmacfg->operation & 0x0003) << 7);
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, pRmacfg->trap_priority);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicReg(RTL8367C_REG_RMA_CTRL_CSSTP, regData);
-}
-/* Function Name:
- *      rtl8367c_getAsicRmaCsstp
- * Description:
- *      Get CSSTP(Cisco Shared Spanning Tree Protocol) for CPU trapping
- * Input:
- *      None
- * Output:
- *      pRmacfg     - type of RMA for trapping frame type setting
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRmaCsstp(rtl8367c_rma_t* pRmacfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_RMA_CTRL_CSSTP, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->operation = ((regData >> 7) & 0x0003);
-    pRmacfg->discard_storm_filter = ((regData >> 6) & 0x0001);
-    pRmacfg->trap_priority = ((regData >> 3) & 0x0007);
-    pRmacfg->keep_format = ((regData >> 2) & 0x0001);
-    pRmacfg->vlan_leaky = ((regData >> 1) & 0x0001);
-    pRmacfg->portiso_leaky = (regData & 0x0001);
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->trap_priority = regData;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicRmaLldp
- * Description:
- *      Set LLDP for CPU trapping
- * Input:
- *      pRmacfg     - type of RMA for trapping frame type setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicRmaLldp(rtk_uint32 enabled, rtl8367c_rma_t* pRmacfg)
-{
-    rtk_uint32 regData = 0;
-    ret_t retVal;
-
-    if(enabled > 1)
-        return RT_ERR_ENABLE;
-
-    if(pRmacfg->operation >= RMAOP_END)
-        return RT_ERR_RMA_ACTION;
-
-    if(pRmacfg->trap_priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_RMA_LLDP_EN, RTL8367C_RMA_LLDP_EN_OFFSET,enabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regData |= (pRmacfg->portiso_leaky & 0x0001);
-    regData |= ((pRmacfg->vlan_leaky & 0x0001) << 1);
-    regData |= ((pRmacfg->keep_format & 0x0001) << 2);
-    regData |= ((pRmacfg->trap_priority & 0x0007) << 3);
-    regData |= ((pRmacfg->discard_storm_filter & 0x0001) << 6);
-    regData |= ((pRmacfg->operation & 0x0003) << 7);
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, pRmacfg->trap_priority);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicReg(RTL8367C_REG_RMA_CTRL_LLDP, regData);
-}
-/* Function Name:
- *      rtl8367c_getAsicRmaLldp
- * Description:
- *      Get LLDP for CPU trapping
- * Input:
- *      None
- * Output:
- *      pRmacfg     - type of RMA for trapping frame type setting
- * Return:
- *      RT_ERR_OK         - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_RMA_ADDR - Invalid RMA address index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicRmaLldp(rtk_uint32 *pEnabled, rtl8367c_rma_t* pRmacfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_RMA_LLDP_EN, RTL8367C_RMA_LLDP_EN_OFFSET,pEnabled);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_REG_RMA_CTRL_LLDP, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->operation = ((regData >> 7) & 0x0003);
-    pRmacfg->discard_storm_filter = ((regData >> 6) & 0x0001);
-    pRmacfg->trap_priority = ((regData >> 3) & 0x0007);
-    pRmacfg->keep_format = ((regData >> 2) & 0x0001);
-    pRmacfg->vlan_leaky = ((regData >> 1) & 0x0001);
-    pRmacfg->portiso_leaky = (regData & 0x0001);
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_RMA_CTRL00, RTL8367C_TRAP_PRIORITY_MASK, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pRmacfg->trap_priority = regData;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_scheduling.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_scheduling.c
deleted file mode 100644
index 8ebd6796dc..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_scheduling.c
+++ /dev/null
@@ -1,525 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Packet Scheduling related functions
- *
- */
-
-#include <rtl8367c_asicdrv_scheduling.h>
-/* Function Name:
- *      rtl8367c_setAsicLeakyBucketParameter
- * Description:
- *      Set Leaky Bucket Paramters
- * Input:
- *      tick    - Tick is used for time slot size unit
- *      token   - Token is used for adding budget in each time slot
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_TICK     - Invalid TICK
- *      RT_ERR_TOKEN    - Invalid TOKEN
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicLeakyBucketParameter(rtk_uint32 tick, rtk_uint32 token)
-{
-    ret_t retVal;
-
-    if(tick > 0xFF)
-        return RT_ERR_TICK;
-
-    if(token > 0xFF)
-        return RT_ERR_TOKEN;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_LEAKY_BUCKET_TICK_REG, RTL8367C_LEAKY_BUCKET_TICK_MASK, tick);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_LEAKY_BUCKET_TOKEN_REG, RTL8367C_LEAKY_BUCKET_TOKEN_MASK, token);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicLeakyBucketParameter
- * Description:
- *      Get Leaky Bucket Paramters
- * Input:
- *      tick    - Tick is used for time slot size unit
- *      token   - Token is used for adding budget in each time slot
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicLeakyBucketParameter(rtk_uint32 *tick, rtk_uint32 *token)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_LEAKY_BUCKET_TICK_REG, RTL8367C_LEAKY_BUCKET_TICK_MASK, tick);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_LEAKY_BUCKET_TOKEN_REG, RTL8367C_LEAKY_BUCKET_TOKEN_MASK, token);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicAprMeter
- * Description:
- *      Set per-port per-queue APR shared meter index
- * Input:
- *      port    - Physical port number (0~10)
- *      qid     - Queue id
- *      apridx  - dedicated shared meter index for APR (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_QUEUE_ID         - Invalid queue id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAprMeter(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 apridx)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    if(apridx > RTL8367C_PORT_QUEUE_METER_INDEX_MAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(port < 8)
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_SCHEDULE_PORT_APR_METER_REG(port, qid), RTL8367C_SCHEDULE_PORT_APR_METER_MASK(qid), apridx);
-    else {
-        regAddr = RTL8367C_REG_SCHEDULE_PORT8_APR_METER_CTRL0 + ((port-8) << 1) + (qid / 5);
-        retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_SCHEDULE_PORT_APR_METER_MASK(qid), apridx);
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicAprMeter
- * Description:
- *      Get per-port per-queue APR shared meter index
- * Input:
- *      port    - Physical port number (0~10)
- *      qid     - Queue id
- *      apridx  - dedicated shared meter index for APR (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- *      RT_ERR_QUEUE_ID - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAprMeter(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 *apridx)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    if(port < 8)
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_SCHEDULE_PORT_APR_METER_REG(port, qid), RTL8367C_SCHEDULE_PORT_APR_METER_MASK(qid), apridx);
-    else {
-        regAddr = RTL8367C_REG_SCHEDULE_PORT8_APR_METER_CTRL0 + ((port-8) << 1) + (qid / 5);
-        retVal = rtl8367c_getAsicRegBits(regAddr, RTL8367C_SCHEDULE_PORT_APR_METER_MASK(qid), apridx);
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicAprEnable
- * Description:
- *      Set per-port APR enable
- * Input:
- *      port        - Physical port number (0~7)
- *      aprEnable   - APR enable seting 1:enable 0:disable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicAprEnable(rtk_uint32 port, rtk_uint32 aprEnable)
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_SCHEDULE_APR_CTRL_REG, RTL8367C_SCHEDULE_APR_CTRL_OFFSET(port), aprEnable);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicAprEnable
- * Description:
- *      Get per-port APR enable
- * Input:
- *      port        - Physical port number (0~7)
- *      aprEnable   - APR enable seting 1:enable 0:disable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicAprEnable(rtk_uint32 port, rtk_uint32 *aprEnable)
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_SCHEDULE_APR_CTRL_REG, RTL8367C_SCHEDULE_APR_CTRL_OFFSET(port), aprEnable);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicWFQWeight
- * Description:
- *      Set weight  of a queue
- * Input:
- *      port    - Physical port number (0~10)
- *      qid     - The queue ID wanted to set
- *      qWeight - The weight value wanted to set (valid:0~127)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_QUEUE_ID         - Invalid queue id
- *      RT_ERR_QOS_QUEUE_WEIGHT - Invalid queue weight
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicWFQWeight(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 qWeight)
-{
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    if(qWeight > RTL8367C_QWEIGHTMAX && qid > 0)
-        return RT_ERR_QOS_QUEUE_WEIGHT;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_SCHEDULE_PORT_QUEUE_WFQ_WEIGHT_REG(port, qid), qWeight);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicWFQWeight
- * Description:
- *      Get weight  of a queue
- * Input:
- *      port    - Physical port number (0~10)
- *      qid     - The queue ID wanted to set
- *      qWeight - The weight value wanted to set (valid:0~127)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_QUEUE_ID         - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicWFQWeight(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 *qWeight)
-{
-    ret_t retVal;
-
-
-    /* Invalid input parameter */
-    if(port  > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_SCHEDULE_PORT_QUEUE_WFQ_WEIGHT_REG(port, qid), qWeight);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicWFQBurstSize
- * Description:
- *      Set WFQ leaky bucket burst size
- * Input:
- *      burstsize   - Leaky bucket burst size, unit byte
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicWFQBurstSize(rtk_uint32 burstsize)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_SCHEDULE_WFQ_BURST_SIZE_REG, burstsize);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicWFQBurstSize
- * Description:
- *      Get WFQ leaky bucket burst size
- * Input:
- *      burstsize   - Leaky bucket burst size, unit byte
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicWFQBurstSize(rtk_uint32 *burstsize)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_SCHEDULE_WFQ_BURST_SIZE_REG, burstsize);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicQueueType
- * Description:
- *      Set type of a queue
- * Input:
- *      port        - Physical port number (0~10)
- *      qid         - The queue ID wanted to set
- *      queueType   - The specified queue type. 0b0: Strict priority, 0b1: WFQ
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- *      RT_ERR_QUEUE_ID - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicQueueType(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 queueType)
-{
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    /* Set Related Registers */
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_SCHEDULE_QUEUE_TYPE_REG(port), RTL8367C_SCHEDULE_QUEUE_TYPE_OFFSET(port, qid),queueType);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicQueueType
- * Description:
- *      Get type of a queue
- * Input:
- *      port        - Physical port number (0~7)
- *      qid         - The queue ID wanted to set
- *      queueType   - The specified queue type. 0b0: Strict priority, 0b1: WFQ
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- *      RT_ERR_QUEUE_ID - Invalid queue id
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicQueueType(rtk_uint32 port, rtk_uint32 qid, rtk_uint32 *queueType)
-{
-    ret_t retVal;
-
-    /* Invalid input parameter */
-    if(port  > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(qid > RTL8367C_QIDMAX)
-        return RT_ERR_QUEUE_ID;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_SCHEDULE_QUEUE_TYPE_REG(port), RTL8367C_SCHEDULE_QUEUE_TYPE_OFFSET(port, qid),queueType);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_setAsicPortEgressRate
- * Description:
- *      Set per-port egress rate
- * Input:
- *      port        - Physical port number (0~10)
- *      rate        - Egress rate
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_QOS_EBW_RATE - Invalid bandwidth/rate
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortEgressRate(rtk_uint32 port, rtk_uint32 rate)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr, regData;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(rate > RTL8367C_QOS_GRANULARTY_MAX)
-        return RT_ERR_QOS_EBW_RATE;
-
-    regAddr = RTL8367C_PORT_EGRESSBW_LSB_REG(port);
-    regData = RTL8367C_QOS_GRANULARTY_LSB_MASK & rate;
-
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_PORT_EGRESSBW_MSB_REG(port);
-    regData = (RTL8367C_QOS_GRANULARTY_MSB_MASK & rate) >> RTL8367C_QOS_GRANULARTY_MSB_OFFSET;
-
-    retVal = rtl8367c_setAsicRegBits(regAddr, RTL8367C_PORT6_EGRESSBW_CTRL1_MASK, regData);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicPortEgressRate
- * Description:
- *      Get per-port egress rate
- * Input:
- *      port        - Physical port number (0~10)
- *      rate        - Egress rate
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortEgressRate(rtk_uint32 port, rtk_uint32 *rate)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr, regData,regData2;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    regAddr = RTL8367C_PORT_EGRESSBW_LSB_REG(port);
-
-    retVal = rtl8367c_getAsicReg(regAddr, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_PORT_EGRESSBW_MSB_REG(port);
-    retVal = rtl8367c_getAsicRegBits(regAddr, RTL8367C_PORT6_EGRESSBW_CTRL1_MASK, &regData2);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *rate = regData | (regData2 << RTL8367C_QOS_GRANULARTY_MSB_OFFSET);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicPortEgressRateIfg
- * Description:
- *      Set per-port egress rate calculate include/exclude IFG
- * Input:
- *      ifg     - 1:include IFG 0:exclude IFG
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortEgressRateIfg(rtk_uint32 ifg)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCHEDULE_WFQ_CTRL, RTL8367C_SCHEDULE_WFQ_CTRL_OFFSET, ifg);
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicPortEgressRateIfg
- * Description:
- *      Get per-port egress rate calculate include/exclude IFG
- * Input:
- *      ifg     - 1:include IFG 0:exclude IFG
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortEgressRateIfg(rtk_uint32 *ifg)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_SCHEDULE_WFQ_CTRL, RTL8367C_SCHEDULE_WFQ_CTRL_OFFSET, ifg);
-
-    return retVal;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_storm.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_storm.c
deleted file mode 100644
index a29f64769d..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_storm.c
+++ /dev/null
@@ -1,851 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Storm control filtering related functions
- *
- */
-
-#include <rtl8367c_asicdrv_storm.h>
-/* Function Name:
- *      rtl8367c_setAsicStormFilterBroadcastEnable
- * Description:
- *      Set per-port broadcast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterBroadcastEnable(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_STORM_BCAST_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterBroadcastEnable
- * Description:
- *      Get per-port broadcast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterBroadcastEnable(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_STORM_BCAST_REG, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicStormFilterBroadcastMeter
- * Description:
- *      Set per-port broadcast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterBroadcastMeter(rtk_uint32 port, rtk_uint32 meter)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_STORM_BCAST_METER_CTRL_REG(port), RTL8367C_STORM_BCAST_METER_CTRL_MASK(port), meter);
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterBroadcastMeter
- * Description:
- *      Get per-port broadcast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      pMeter  - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterBroadcastMeter(rtk_uint32 port, rtk_uint32 *pMeter)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_STORM_BCAST_METER_CTRL_REG(port), RTL8367C_STORM_BCAST_METER_CTRL_MASK(port), pMeter);
-}
-/* Function Name:
- *      rtl8367c_setAsicStormFilterMulticastEnable
- * Description:
- *      Set per-port multicast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterMulticastEnable(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_STORM_MCAST_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterMulticastEnable
- * Description:
- *      Get per-port multicast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterMulticastEnable(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_STORM_MCAST_REG, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicStormFilterMulticastMeter
- * Description:
- *      Set per-port multicast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterMulticastMeter(rtk_uint32 port, rtk_uint32 meter)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_STORM_MCAST_METER_CTRL_REG(port), RTL8367C_STORM_MCAST_METER_CTRL_MASK(port), meter);
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterMulticastMeter
- * Description:
- *      Get per-port multicast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      pMeter  - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterMulticastMeter(rtk_uint32 port, rtk_uint32 *pMeter)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_STORM_MCAST_METER_CTRL_REG(port), RTL8367C_STORM_MCAST_METER_CTRL_MASK(port), pMeter);
-}
-/* Function Name:
- *      rtl8367c_setAsicStormFilterUnknownMulticastEnable
- * Description:
- *      Set per-port unknown multicast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterUnknownMulticastEnable(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_STORM_UNKNOWN_MCAST_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterUnknownMulticastEnable
- * Description:
- *      Get per-port unknown multicast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterUnknownMulticastEnable(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_STORM_UNKNOWN_MCAST_REG, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicStormFilterUnknownMulticastMeter
- * Description:
- *      Set per-port unknown multicast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterUnknownMulticastMeter(rtk_uint32 port, rtk_uint32 meter)
-{
-    ret_t retVal;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_STORM_UNMC_METER_CTRL_REG(port), RTL8367C_STORM_UNMC_METER_CTRL_MASK(port), meter);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_STORM_UNMC_METER_CTRL4 + ((port - 8) >> 1), RTL8367C_STORM_UNMC_METER_CTRL_MASK(port), meter);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterUnknownMulticastMeter
- * Description:
- *      Get per-port unknown multicast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      pMeter  - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterUnknownMulticastMeter(rtk_uint32 port, rtk_uint32 *pMeter)
-{
-    ret_t retVal;
-
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_STORM_UNMC_METER_CTRL_REG(port), RTL8367C_STORM_UNMC_METER_CTRL_MASK(port), pMeter);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_STORM_UNMC_METER_CTRL4 + ((port - 8) >> 1), RTL8367C_STORM_UNMC_METER_CTRL_MASK(port), pMeter);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicStormFilterUnknownUnicastEnable
- * Description:
- *      Set per-port unknown unicast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterUnknownUnicastEnable(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_STORM_UNKNOWN_UCAST_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterUnknownUnicastEnable
- * Description:
- *      get per-port unknown unicast storm filter enable/disable
- * Input:
- *      port    - Physical port number (0~7)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterUnknownUnicastEnable(rtk_uint32 port, rtk_uint32 *pEnabled)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_STORM_UNKNOWN_UCAST_REG, port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicStormFilterUnknownUnicastMeter
- * Description:
- *      Set per-port unknown unicast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterUnknownUnicastMeter(rtk_uint32 port, rtk_uint32 meter)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_STORM_UNDA_METER_CTRL_REG(port), RTL8367C_STORM_UNDA_METER_CTRL_MASK(port), meter);
-}
-/* Function Name:
- *      rtl8367c_getAsicStormFilterUnknownUnicastMeter
- * Description:
- *      Get per-port unknown unicast storm filter meter
- * Input:
- *      port    - Physical port number (0~7)
- *      pMeter  - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterUnknownUnicastMeter(rtk_uint32 port, rtk_uint32 *pMeter)
-{
-    if(port >= RTL8367C_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_STORM_UNDA_METER_CTRL_REG(port), RTL8367C_STORM_UNDA_METER_CTRL_MASK(port), pMeter);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtBroadcastMeter
- * Description:
- *      Set extension broadcast storm filter meter
- * Input:
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtBroadcastMeter(rtk_uint32 meter)
-{
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG0, RTL8367C_BC_STORM_EXT_METERIDX_MASK, meter);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtBroadcastMeter
- * Description:
- *      get extension broadcast storm filter meter
- * Input:
- *      None
- * Output:
- *      pMeter  - meter index (0~31)
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtBroadcastMeter(rtk_uint32 *pMeter)
-{
-    if(NULL == pMeter)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG0, RTL8367C_BC_STORM_EXT_METERIDX_MASK, pMeter);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtMulticastMeter
- * Description:
- *      Set extension multicast storm filter meter
- * Input:
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtMulticastMeter(rtk_uint32 meter)
-{
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG0, RTL8367C_MC_STORM_EXT_METERIDX_MASK, meter);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtMulticastMeter
- * Description:
- *      get extension multicast storm filter meter
- * Input:
- *      None
- * Output:
- *      pMeter  - meter index (0~31)
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtMulticastMeter(rtk_uint32 *pMeter)
-{
-    if(NULL == pMeter)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG0, RTL8367C_MC_STORM_EXT_METERIDX_MASK, pMeter);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtUnknownMulticastMeter
- * Description:
- *      Set extension unknown multicast storm filter meter
- * Input:
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtUnknownMulticastMeter(rtk_uint32 meter)
-{
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG1, RTL8367C_UNMC_STORM_EXT_METERIDX_MASK, meter);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtUnknownMulticastMeter
- * Description:
- *      get extension unknown multicast storm filter meter
- * Input:
- *      None
- * Output:
- *      pMeter  - meter index (0~31)
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtUnknownMulticastMeter(rtk_uint32 *pMeter)
-{
-    if(NULL == pMeter)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG1, RTL8367C_UNMC_STORM_EXT_METERIDX_MASK, pMeter);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtUnknownUnicastMeter
- * Description:
- *      Set extension unknown unicast storm filter meter
- * Input:
- *      meter   - meter index (0~31)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_FILTER_METER_ID  - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtUnknownUnicastMeter(rtk_uint32 meter)
-{
-    if(meter > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG1, RTL8367C_UNUC_STORM_EXT_METERIDX_MASK, meter);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtUnknownUnicastMeter
- * Description:
- *      get extension unknown unicast storm filter meter
- * Input:
- *      None
- * Output:
- *      pMeter  - meter index (0~31)
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Invalid meter index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtUnknownUnicastMeter(rtk_uint32 *pMeter)
-{
-    if(NULL == pMeter)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_STORM_EXT_MTRIDX_CFG1, RTL8367C_UNUC_STORM_EXT_METERIDX_MASK, pMeter);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtBroadcastEnable
- * Description:
- *      Set extension broadcast storm filter state
- * Input:
- *      enabled     - state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtBroadcastEnable(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_BCAST_EXT_EN_OFFSET, enabled);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtBroadcastEnable
- * Description:
- *      Get extension broadcast storm filter state
- * Input:
- *      None
- * Output:
- *      pEnabled    - state
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtBroadcastEnable(rtk_uint32 *pEnabled)
-{
-    if(NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_BCAST_EXT_EN_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtMulticastEnable
- * Description:
- *      Set extension multicast storm filter state
- * Input:
- *      enabled     - state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtMulticastEnable(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_MCAST_EXT_EN_OFFSET, enabled);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtMulticastEnable
- * Description:
- *      Get extension multicast storm filter state
- * Input:
- *      None
- * Output:
- *      pEnabled    - state
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtMulticastEnable(rtk_uint32 *pEnabled)
-{
-    if(NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_MCAST_EXT_EN_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtUnknownMulticastEnable
- * Description:
- *      Set extension unknown multicast storm filter state
- * Input:
- *      enabled     - state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtUnknownMulticastEnable(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_UNKNOWN_MCAST_EXT_EN_OFFSET, enabled);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtUnknownMulticastEnable
- * Description:
- *      Get extension unknown multicast storm filter state
- * Input:
- *      None
- * Output:
- *      pEnabled    - state
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtUnknownMulticastEnable(rtk_uint32 *pEnabled)
-{
-    if(NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_UNKNOWN_MCAST_EXT_EN_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtUnknownUnicastEnable
- * Description:
- *      Set extension unknown unicast storm filter state
- * Input:
- *      enabled     - state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtUnknownUnicastEnable(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_UNKNOWN_UCAST_EXT_EN_OFFSET, enabled);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtUnknownUnicastEnable
- * Description:
- *      Get extension unknown unicast storm filter state
- * Input:
- *      None
- * Output:
- *      pEnabled    - state
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtUnknownUnicastEnable(rtk_uint32 *pEnabled)
-{
-    if(NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_UNKNOWN_UCAST_EXT_EN_OFFSET, pEnabled);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicStormFilterExtEnablePortMask
- * Description:
- *      Set extension storm filter port mask
- * Input:
- *      portmask    - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicStormFilterExtEnablePortMask(rtk_uint32 portmask)
-{
-    ret_t retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_EXT_EN_PORTMASK_MASK, portmask & 0x3FF);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_EXT_EN_PORTMASK_EXT_MASK, (portmask >> 10)&1);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicStormFilterExtEnablePortMask
- * Description:
- *      Get extension storm filter port mask
- * Input:
- *      portmask    - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_NULL_POINTER     - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicStormFilterExtEnablePortMask(rtk_uint32 *pPortmask)
-{
-    rtk_uint32 tmpPmsk;
-    ret_t retVal;
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_EXT_EN_PORTMASK_MASK, &tmpPmsk);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask = tmpPmsk & 0x3ff;
-
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_STORM_EXT_CFG, RTL8367C_STORM_EXT_EN_PORTMASK_EXT_MASK, &tmpPmsk);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-    *pPortmask |= (tmpPmsk & 1) << 10;
-
-    return RT_ERR_OK;
-}
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_svlan.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_svlan.c
deleted file mode 100644
index f19ceba5a9..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_svlan.c
+++ /dev/null
@@ -1,1003 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : SVLAN related functions
- *
- */
-#include <rtl8367c_asicdrv_svlan.h>
-
-#include <string.h>
-
-static void _rtl8367c_svlanConfStUser2Smi( rtl8367c_svlan_memconf_t *pUserSt, rtk_uint16 *pSmiSt)
-{
-    pSmiSt[0] |= (pUserSt->vs_member & 0x00FF);
-    pSmiSt[0] |= (pUserSt->vs_untag & 0x00FF) << 8;
-
-    pSmiSt[1] |= (pUserSt->vs_fid_msti & 0x000F);
-    pSmiSt[1] |= (pUserSt->vs_priority & 0x0007) << 4;
-    pSmiSt[1] |= (pUserSt->vs_force_fid & 0x0001) << 7;
-
-    pSmiSt[2] |= (pUserSt->vs_svid & 0x0FFF);
-    pSmiSt[2] |= (pUserSt->vs_efiden & 0x0001) << 12;
-    pSmiSt[2] |= (pUserSt->vs_efid & 0x0007) << 13;
-
-    pSmiSt[3] |= ((pUserSt->vs_member & 0x0700) >> 8);
-    pSmiSt[3] |= ((pUserSt->vs_untag & 0x0700) >> 8) << 3;
-}
-
-static void _rtl8367c_svlanConfStSmi2User( rtl8367c_svlan_memconf_t *pUserSt, rtk_uint16 *pSmiSt)
-{
-
-    pUserSt->vs_member = (pSmiSt[0] & 0x00FF) | ((pSmiSt[3] & 0x0007) << 8);
-    pUserSt->vs_untag = ((pSmiSt[0] & 0xFF00) >> 8) | (((pSmiSt[3] & 0x0038) >> 3) << 8);
-
-    pUserSt->vs_fid_msti = (pSmiSt[1] & 0x000F);
-    pUserSt->vs_priority = (pSmiSt[1] & 0x0070) >> 4;
-    pUserSt->vs_force_fid = (pSmiSt[1] & 0x0080) >> 7;
-
-    pUserSt->vs_svid = (pSmiSt[2] & 0x0FFF);
-    pUserSt->vs_efiden = (pSmiSt[2] & 0x1000) >> 12;
-    pUserSt->vs_efid = (pSmiSt[2] & 0xE000) >> 13;
-}
-
-static void _rtl8367c_svlanMc2sStUser2Smi(rtl8367c_svlan_mc2s_t *pUserSt, rtk_uint16 *pSmiSt)
-{
-    pSmiSt[0] |= (pUserSt->svidx & 0x003F);
-    pSmiSt[0] |= (pUserSt->format & 0x0001) << 6;
-    pSmiSt[0] |= (pUserSt->valid & 0x0001) << 7;
-
-    pSmiSt[1] = (rtk_uint16)(pUserSt->smask & 0x0000FFFF);
-    pSmiSt[2] = (rtk_uint16)((pUserSt->smask & 0xFFFF0000) >> 16);
-
-    pSmiSt[3] = (rtk_uint16)(pUserSt->sdata & 0x0000FFFF);
-    pSmiSt[4] = (rtk_uint16)((pUserSt->sdata & 0xFFFF0000) >> 16);
-}
-
-static void _rtl8367c_svlanMc2sStSmi2User(rtl8367c_svlan_mc2s_t *pUserSt, rtk_uint16 *pSmiSt)
-{
-    pUserSt->svidx = (pSmiSt[0] & 0x003F);
-    pUserSt->format = (pSmiSt[0] & 0x0040) >> 6;
-    pUserSt->valid = (pSmiSt[0] & 0x0080) >> 7;
-
-    pUserSt->smask = pSmiSt[1] | (pSmiSt[2] << 16);
-    pUserSt->sdata = pSmiSt[3] | (pSmiSt[4] << 16);
-}
-
-static void _rtl8367c_svlanSp2cStUser2Smi(rtl8367c_svlan_s2c_t *pUserSt, rtk_uint16 *pSmiSt)
-{
-    pSmiSt[0] |= (pUserSt->dstport & 0x0007);
-    pSmiSt[0] |= (pUserSt->svidx & 0x003F) << 3;
-    pSmiSt[0] |= ((pUserSt->dstport & 0x0008) >> 3) << 9;
-
-    pSmiSt[1] |= (pUserSt->vid & 0x0FFF);
-    pSmiSt[1] |= (pUserSt->valid & 0x0001) << 12;
-}
-
-static void _rtl8367c_svlanSp2cStSmi2User(rtl8367c_svlan_s2c_t *pUserSt, rtk_uint16 *pSmiSt)
-{
-    pUserSt->dstport = (((pSmiSt[0] & 0x0200) >> 9) << 3) | (pSmiSt[0] & 0x0007);
-    pUserSt->svidx   = (pSmiSt[0] & 0x01F8) >> 3;
-    pUserSt->vid     = (pSmiSt[1] & 0x0FFF);
-    pUserSt->valid   = (pSmiSt[1] & 0x1000) >> 12;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicSvlanUplinkPortMask
- * Description:
- *      Set uplink ports mask
- * Input:
- *      portMask    - Uplink port mask setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanUplinkPortMask(rtk_uint32 portMask)
-{
-    return rtl8367c_setAsicReg(RTL8367C_REG_SVLAN_UPLINK_PORTMASK, portMask);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanUplinkPortMask
- * Description:
- *      Get uplink ports mask
- * Input:
- *      pPortmask   - Uplink port mask setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanUplinkPortMask(rtk_uint32* pPortmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_SVLAN_UPLINK_PORTMASK, pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanTpid
- * Description:
- *      Set accepted S-VLAN ether type. The default ether type of S-VLAN is 0x88a8
- * Input:
- *      protocolType    - Ether type of S-tag frame parsing in uplink ports
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      Ether type of S-tag in 802.1ad is 0x88a8 and there are existed ether type 0x9100 and 0x9200
- *      for Q-in-Q SLAN design. User can set mathced ether type as service provider supported protocol
- */
-ret_t rtl8367c_setAsicSvlanTpid(rtk_uint32 protocolType)
-{
-    return rtl8367c_setAsicReg(RTL8367C_REG_VS_TPID, protocolType);
-}
-/* Function Name:
- *      rtl8367c_getAsicReg
- * Description:
- *      Get accepted S-VLAN ether type. The default ether type of S-VLAN is 0x88a8
- * Input:
- *      pProtocolType   - Ether type of S-tag frame parsing in uplink ports
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanTpid(rtk_uint32* pProtocolType)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_VS_TPID, pProtocolType);
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanPrioritySel
- * Description:
- *      Set SVLAN priority field setting
- * Input:
- *      priSel  - S-priority assignment method, 0:internal priority 1:C-tag priority 2:using Svlan member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanPrioritySel(rtk_uint32 priSel)
-{
-    if(priSel >= SPRISEL_END)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_SPRISEL_MASK, priSel);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanPrioritySel
- * Description:
- *      Get SVLAN priority field setting
- * Input:
- *      pPriSel     - S-priority assignment method, 0:internal priority 1:C-tag priority 2:using Svlan member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanPrioritySel(rtk_uint32* pPriSel)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_SPRISEL_MASK, pPriSel);
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanTrapPriority
- * Description:
- *      Set trap to CPU priority assignment
- * Input:
- *      priority    - Priority assignment
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanTrapPriority(rtk_uint32 priority)
-{
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_QOS_TRAP_PRIORITY0, RTL8367C_SVLAN_PRIOIRTY_MASK, priority);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanTrapPriority
- * Description:
- *      Get trap to CPU priority assignment
- * Input:
- *      pPriority   - Priority assignment
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanTrapPriority(rtk_uint32* pPriority)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_QOS_TRAP_PRIORITY0, RTL8367C_SVLAN_PRIOIRTY_MASK, pPriority);
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanDefaultVlan
- * Description:
- *      Set default egress SVLAN
- * Input:
- *      port    - Physical port number (0~10)
- *      index   - index SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number
- *      RT_ERR_SVLAN_ENTRY_INDEX    - Invalid SVLAN index parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanDefaultVlan(rtk_uint32 port, rtk_uint32 index)
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(index > RTL8367C_SVIDXMAX)
-        return RT_ERR_SVLAN_ENTRY_INDEX;
-
-    if(port < 8){
-        if(port & 1)
-            retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL0 + (port >> 1), RTL8367C_VS_PORT1_SVIDX_MASK,index);
-        else
-            retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL0 + (port >> 1), RTL8367C_VS_PORT0_SVIDX_MASK,index);
-    }else{
-        switch(port){
-            case 8:
-                retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL4, RTL8367C_VS_PORT8_SVIDX_MASK,index);
-                break;
-
-            case 9:
-                retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL4, RTL8367C_VS_PORT9_SVIDX_MASK,index);
-                break;
-
-            case 10:
-                retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL5, RTL8367C_SVLAN_PORTBASED_SVIDX_CTRL5_MASK,index);
-                break;
-        }
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanDefaultVlan
- * Description:
- *      Get default egress SVLAN
- * Input:
- *      port    - Physical port number (0~7)
- *      pIndex  - index SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanDefaultVlan(rtk_uint32 port, rtk_uint32* pIndex)
-{
-    ret_t retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8){
-        if(port & 1)
-            retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL0 + (port >> 1), RTL8367C_VS_PORT1_SVIDX_MASK,pIndex);
-        else
-            retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL0 + (port >> 1), RTL8367C_VS_PORT0_SVIDX_MASK,pIndex);
-    }else{
-        switch(port){
-            case 8:
-                retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL4, RTL8367C_VS_PORT8_SVIDX_MASK,pIndex);
-                break;
-
-            case 9:
-                retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL4, RTL8367C_VS_PORT9_SVIDX_MASK,pIndex);
-                break;
-
-            case 10:
-                retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_PORTBASED_SVIDX_CTRL5, RTL8367C_SVLAN_PORTBASED_SVIDX_CTRL5_MASK,pIndex);
-                break;
-        }
-    }
-
-    return retVal;
-
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanIngressUntag
- * Description:
- *      Set action received un-Stag frame from unplink port
- * Input:
- *      mode        - 0:Drop 1:Trap 2:Assign SVLAN
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanIngressUntag(rtk_uint32 mode)
-{
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_UNTAG_MASK, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanIngressUntag
- * Description:
- *      Get action received un-Stag frame from unplink port
- * Input:
- *      pMode       - 0:Drop 1:Trap 2:Assign SVLAN
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanIngressUntag(rtk_uint32* pMode)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_UNTAG_MASK, pMode);
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanIngressUnmatch
- * Description:
- *      Set action received unmatched Stag frame from unplink port
- * Input:
- *      mode        - 0:Drop 1:Trap 2:Assign SVLAN
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanIngressUnmatch(rtk_uint32 mode)
-{
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_UNMAT_MASK, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanIngressUnmatch
- * Description:
- *      Get action received unmatched Stag frame from unplink port
- * Input:
- *      pMode       - 0:Drop 1:Trap 2:Assign SVLAN
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanIngressUnmatch(rtk_uint32* pMode)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_UNMAT_MASK, pMode);
-
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanEgressUnassign
- * Description:
- *      Set unplink stream without egress SVID action
- * Input:
- *      enabled     - 1:Trap egress unassigned frames to CPU, 0: Use SVLAN setup in VS_CPSVIDX as egress SVID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanEgressUnassign(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_UIFSEG_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanEgressUnassign
- * Description:
- *      Get unplink stream without egress SVID action
- * Input:
- *      pEnabled    - 1:Trap egress unassigned frames to CPU, 0: Use SVLAN setup in VS_CPSVIDX as egress SVID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanEgressUnassign(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_UIFSEG_OFFSET, pEnabled);
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicSvlanMemberConfiguration
- * Description:
- *      Set system 64 S-tag content
- * Input:
- *      index           - index of 64 s-tag configuration
- *      pSvlanMemCfg    - SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_SVLAN_ENTRY_INDEX    - Invalid SVLAN index parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanMemberConfiguration(rtk_uint32 index, rtl8367c_svlan_memconf_t* pSvlanMemCfg)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr, regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smiSvlanMemConf[RTL8367C_SVLAN_MEMCONF_LEN];
-
-    if(index > RTL8367C_SVIDXMAX)
-        return RT_ERR_SVLAN_ENTRY_INDEX;
-
-    memset(smiSvlanMemConf, 0x00, sizeof(rtk_uint16) * RTL8367C_SVLAN_MEMCONF_LEN);
-    _rtl8367c_svlanConfStUser2Smi(pSvlanMemCfg, smiSvlanMemConf);
-
-    accessPtr = smiSvlanMemConf;
-
-    regData = *accessPtr;
-    for(i = 0; i < 3; i++)
-    {
-        retVal = rtl8367c_setAsicReg(RTL8367C_SVLAN_MEMBERCFG_BASE_REG(index) + i, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        accessPtr ++;
-        regData = *accessPtr;
-    }
-
-    if(index < 63)
-        regAddr = RTL8367C_REG_SVLAN_MEMBERCFG0_CTRL4+index;
-    else if(index == 63)
-        regAddr = RTL8367C_REG_SVLAN_MEMBERCFG63_CTRL4;
-
-    retVal = rtl8367c_setAsicReg(regAddr, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanMemberConfiguration
- * Description:
- *      Get system 64 S-tag content
- * Input:
- *      index           - index of 64 s-tag configuration
- *      pSvlanMemCfg    - SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_SVLAN_ENTRY_INDEX    - Invalid SVLAN index parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanMemberConfiguration(rtk_uint32 index,rtl8367c_svlan_memconf_t* pSvlanMemCfg)
-{
-    ret_t retVal;
-    rtk_uint32 regAddr,regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smiSvlanMemConf[RTL8367C_SVLAN_MEMCONF_LEN];
-
-    if(index > RTL8367C_SVIDXMAX)
-        return RT_ERR_SVLAN_ENTRY_INDEX;
-
-    memset(smiSvlanMemConf, 0x00, sizeof(rtk_uint16) * RTL8367C_SVLAN_MEMCONF_LEN);
-
-    accessPtr = smiSvlanMemConf;
-
-    for(i = 0; i < 3; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_SVLAN_MEMBERCFG_BASE_REG(index) + i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *accessPtr = regData;
-
-        accessPtr ++;
-    }
-
-    if(index < 63)
-        regAddr = RTL8367C_REG_SVLAN_MEMBERCFG0_CTRL4+index;
-    else if(index == 63)
-        regAddr = RTL8367C_REG_SVLAN_MEMBERCFG63_CTRL4;
-
-    retVal = rtl8367c_getAsicReg(regAddr, &regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    *accessPtr = regData;
-
-    _rtl8367c_svlanConfStSmi2User(pSvlanMemCfg, smiSvlanMemConf);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanC2SConf
- * Description:
- *      Set SVLAN C2S table
- * Input:
- *      index   - index of 128 Svlan C2S configuration
- *      evid    - Enhanced VID
- *      portmask    - available c2s port mask
- *      svidx   - index of 64 Svlan member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENTRY_INDEX  - Invalid entry index
- * Note:
- *      ASIC will check upstream's VID and assign related SVID to mathed packet
- */
-ret_t rtl8367c_setAsicSvlanC2SConf(rtk_uint32 index, rtk_uint32 evid, rtk_uint32 portmask, rtk_uint32 svidx)
-{
-    ret_t retVal;
-
-    if(index > RTL8367C_C2SIDXMAX)
-        return RT_ERR_ENTRY_INDEX;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_SVLAN_C2SCFG_BASE_REG(index), svidx);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_SVLAN_C2SCFG_BASE_REG(index) + 1, portmask);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_setAsicReg(RTL8367C_SVLAN_C2SCFG_BASE_REG(index) + 2, evid);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanC2SConf
- * Description:
- *      Get SVLAN C2S table
- * Input:
- *      index   - index of 128 Svlan C2S configuration
- *      pEvid   - Enhanced VID
- *      pPortmask   - available c2s port mask
- *      pSvidx  - index of 64 Svlan member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENTRY_INDEX  - Invalid entry index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanC2SConf(rtk_uint32 index, rtk_uint32* pEvid, rtk_uint32* pPortmask, rtk_uint32* pSvidx)
-{
-    ret_t retVal;
-
-    if(index > RTL8367C_C2SIDXMAX)
-        return RT_ERR_ENTRY_INDEX;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_SVLAN_C2SCFG_BASE_REG(index), pSvidx);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_SVLAN_C2SCFG_BASE_REG(index) + 1, pPortmask);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    retVal = rtl8367c_getAsicReg(RTL8367C_SVLAN_C2SCFG_BASE_REG(index) + 2, pEvid);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicSvlanMC2SConf
- * Description:
- *      Set system MC2S content
- * Input:
- *      index           - index of 32 SVLAN 32 MC2S configuration
- *      pSvlanMc2sCfg   - SVLAN Multicast to SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENTRY_INDEX  - Invalid entry index
- * Note:
- *      If upstream packet is L2 multicast or IPv4 multicast packet and DMAC/DIP is matched MC2S
- *      configuration, ASIC will assign egress SVID to the packet
- */
-ret_t rtl8367c_setAsicSvlanMC2SConf(rtk_uint32 index,rtl8367c_svlan_mc2s_t* pSvlanMc2sCfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smiSvlanMC2S[RTL8367C_SVLAN_MC2S_LEN];
-
-    if(index > RTL8367C_MC2SIDXMAX)
-        return RT_ERR_ENTRY_INDEX;
-
-    memset(smiSvlanMC2S, 0x00, sizeof(rtk_uint16) * RTL8367C_SVLAN_MC2S_LEN);
-    _rtl8367c_svlanMc2sStUser2Smi(pSvlanMc2sCfg, smiSvlanMC2S);
-
-    accessPtr = smiSvlanMC2S;
-
-    regData = *accessPtr;
-    for(i = 0; i < 5; i++)
-    {
-        retVal = rtl8367c_setAsicReg(RTL8367C_SVLAN_MCAST2S_ENTRY_BASE_REG(index) + i, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        accessPtr ++;
-        regData = *accessPtr;
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanMC2SConf
- * Description:
- *      Get system MC2S content
- * Input:
- *      index           - index of 32 SVLAN 32 MC2S configuration
- *      pSvlanMc2sCfg   - SVLAN Multicast to SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENTRY_INDEX  - Invalid entry index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanMC2SConf(rtk_uint32 index, rtl8367c_svlan_mc2s_t* pSvlanMc2sCfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smiSvlanMC2S[RTL8367C_SVLAN_MC2S_LEN];
-
-    if(index > RTL8367C_MC2SIDXMAX)
-        return RT_ERR_ENTRY_INDEX;
-
-    memset(smiSvlanMC2S, 0x00, sizeof(rtk_uint16) * RTL8367C_SVLAN_MC2S_LEN);
-
-    accessPtr = smiSvlanMC2S;
-
-    for(i = 0; i < 5; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_SVLAN_MCAST2S_ENTRY_BASE_REG(index) + i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *accessPtr = regData;
-        accessPtr ++;
-    }
-
-
-    _rtl8367c_svlanMc2sStSmi2User(pSvlanMc2sCfg, smiSvlanMC2S);
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicSvlanSP2CConf
- * Description:
- *      Set system 128 SP2C content
- * Input:
- *      index           - index of 128 SVLAN & Port to CVLAN configuration
- *      pSvlanSp2cCfg   - SVLAN & Port to CVLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENTRY_INDEX  - Invalid entry index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanSP2CConf(rtk_uint32 index, rtl8367c_svlan_s2c_t* pSvlanSp2cCfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smiSvlanSP2C[RTL8367C_SVLAN_SP2C_LEN];
-
-    if(index > RTL8367C_SP2CMAX)
-        return RT_ERR_ENTRY_INDEX;
-
-    memset(smiSvlanSP2C, 0x00, sizeof(rtk_uint16) * RTL8367C_SVLAN_SP2C_LEN);
-    _rtl8367c_svlanSp2cStUser2Smi(pSvlanSp2cCfg,smiSvlanSP2C);
-
-    accessPtr = smiSvlanSP2C;
-
-    regData = *accessPtr;
-    for(i = 0; i < 2; i++)
-    {
-        retVal = rtl8367c_setAsicReg(RTL8367C_SVLAN_S2C_ENTRY_BASE_REG(index) + i, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        accessPtr ++;
-        regData = *accessPtr;
-    }
-
-    return retVal;
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanSP2CConf
- * Description:
- *      Get system 128 SP2C content
- * Input:
- *      index           - index of 128 SVLAN & Port to CVLAN configuration
- *      pSvlanSp2cCfg   - SVLAN & Port to CVLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENTRY_INDEX  - Invalid entry index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanSP2CConf(rtk_uint32 index,rtl8367c_svlan_s2c_t* pSvlanSp2cCfg)
-{
-    ret_t retVal;
-    rtk_uint32 regData;
-    rtk_uint16 *accessPtr;
-    rtk_uint32 i;
-    rtk_uint16 smiSvlanSP2C[RTL8367C_SVLAN_SP2C_LEN];
-
-    if(index > RTL8367C_SP2CMAX)
-        return RT_ERR_ENTRY_INDEX;
-
-    memset(smiSvlanSP2C, 0x00, sizeof(rtk_uint16) * RTL8367C_SVLAN_SP2C_LEN);
-
-    accessPtr = smiSvlanSP2C;
-
-    for(i = 0; i < 2; i++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_SVLAN_S2C_ENTRY_BASE_REG(index) + i, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *accessPtr = regData;
-
-        accessPtr ++;
-    }
-
-    _rtl8367c_svlanSp2cStSmi2User(pSvlanSp2cCfg, smiSvlanSP2C);
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanDmacCvidSel
- * Description:
- *      Set downstream CVID decision by DMAC
- * Input:
- *      port        - Physical port number (0~7)
- *      enabled     - 0:disabled, 1:enabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanDmacCvidSel(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_PORT0_DMACVIDSEL_OFFSET + port, enabled);
-    else
-        return rtl8367c_setAsicRegBit(RTL8367C_REG_SVLAN_CFG_EXT, RTL8367C_VS_PORT8_DMACVIDSEL_OFFSET + (port-8), enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanDmacCvidSel
- * Description:
- *      Get downstream CVID decision by DMAC
- * Input:
- *      port        - Physical port number (0~7)
- *      pEnabled    - 0:disabled, 1:enabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanDmacCvidSel(rtk_uint32 port, rtk_uint32* pEnabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_SVLAN_CFG, RTL8367C_VS_PORT0_DMACVIDSEL_OFFSET + port, pEnabled);
-    else
-        return rtl8367c_getAsicRegBit(RTL8367C_REG_SVLAN_CFG_EXT, RTL8367C_VS_PORT8_DMACVIDSEL_OFFSET + (port-8), pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicSvlanUntagVlan
- * Description:
- *      Set default ingress untag SVLAN
- * Input:
- *      index   - index SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_SVLAN_ENTRY_INDEX    - Invalid SVLAN index parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanUntagVlan(rtk_uint32 index)
-{
-    if(index > RTL8367C_SVIDXMAX)
-        return RT_ERR_SVLAN_ENTRY_INDEX;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_UNTAG_UNMAT_CFG, RTL8367C_VS_UNTAG_SVIDX_MASK, index);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanUntagVlan
- * Description:
- *      Get default ingress untag SVLAN
- * Input:
- *      pIndex  - index SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanUntagVlan(rtk_uint32* pIndex)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_UNTAG_UNMAT_CFG, RTL8367C_VS_UNTAG_SVIDX_MASK, pIndex);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicSvlanUnmatchVlan
- * Description:
- *      Set default ingress unmatch SVLAN
- * Input:
- *      index   - index SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_SVLAN_ENTRY_INDEX    - Invalid SVLAN index parameter
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanUnmatchVlan(rtk_uint32 index)
-{
-    if(index > RTL8367C_SVIDXMAX)
-        return RT_ERR_SVLAN_ENTRY_INDEX;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_SVLAN_UNTAG_UNMAT_CFG, RTL8367C_VS_UNMAT_SVIDX_MASK, index);
-}
-/* Function Name:
- *      rtl8367c_getAsicSvlanUnmatchVlan
- * Description:
- *      Get default ingress unmatch SVLAN
- * Input:
- *      pIndex  - index SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanUnmatchVlan(rtk_uint32* pIndex)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_SVLAN_UNTAG_UNMAT_CFG, RTL8367C_VS_UNMAT_SVIDX_MASK, pIndex);
-}
-
-
-/* Function Name:
- *      rtl8367c_setAsicSvlanLookupType
- * Description:
- *      Set svlan lookup table selection
- * Input:
- *      type    - lookup type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSvlanLookupType(rtk_uint32 type)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_SVLAN_LOOKUP_TYPE, RTL8367C_SVLAN_LOOKUP_TYPE_OFFSET, type);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicSvlanLookupType
- * Description:
- *      Get svlan lookup table selection
- * Input:
- *      pType   - lookup type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSvlanLookupType(rtk_uint32* pType)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_SVLAN_LOOKUP_TYPE, RTL8367C_SVLAN_LOOKUP_TYPE_OFFSET, pType);
-}
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_trunking.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_trunking.c
deleted file mode 100644
index 26d4c29b83..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_trunking.c
+++ /dev/null
@@ -1,356 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Port trunking related functions
- *
- */
-
-#include <rtl8367c_asicdrv_trunking.h>
-/* Function Name:
- *      rtl8367c_setAsicTrunkingMode
- * Description:
- *      Set port trunking mode
- * Input:
- *      mode    - 1:dumb 0:user defined
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicTrunkingMode(rtk_uint32 mode)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_PORT_TRUNK_CTRL, RTL8367C_PORT_TRUNK_DUMB_OFFSET, mode);
-}
-/* Function Name:
- *      rtl8367c_getAsicTrunkingMode
- * Description:
- *      Get port trunking mode
- * Input:
- *      pMode   - 1:dumb 0:user defined
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTrunkingMode(rtk_uint32* pMode)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_PORT_TRUNK_CTRL, RTL8367C_PORT_TRUNK_DUMB_OFFSET, pMode);
-}
-/* Function Name:
- *      rtl8367c_setAsicTrunkingFc
- * Description:
- *      Set port trunking flow control
- * Input:
- *      group       - Trunk Group ID
- *      enabled     - 0:disable, 1:enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicTrunkingFc(rtk_uint32 group, rtk_uint32 enabled)
-{
-    ret_t       retVal;
-
-    if(group > RTL8367C_MAX_TRUNK_GID)
-        return RT_ERR_LA_TRUNK_ID;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_PORT_TRUNK_DROP_CTRL, RTL8367C_PORT_TRUNK_DROP_CTRL_OFFSET, ENABLED)) != RT_ERR_OK)
-        return retVal;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_PORT_TRUNK_FLOWCTRL, (RTL8367C_EN_FLOWCTRL_TG0_OFFSET + group), enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicTrunkingFc
- * Description:
- *      Get port trunking flow control
- * Input:
- *      group       - Trunk Group ID
- *      pEnabled    - 0:disable, 1:enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTrunkingFc(rtk_uint32 group, rtk_uint32* pEnabled)
-{
-    if(group > RTL8367C_MAX_TRUNK_GID)
-        return RT_ERR_LA_TRUNK_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_PORT_TRUNK_FLOWCTRL, (RTL8367C_EN_FLOWCTRL_TG0_OFFSET + group), pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicTrunkingGroup
- * Description:
- *      Set trunking group available port mask
- * Input:
- *      group       - Trunk Group ID
- *      portmask    - Logic trunking enable port mask, max 4 ports
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicTrunkingGroup(rtk_uint32 group, rtk_uint32 portmask)
-{
-    if(group > RTL8367C_MAX_TRUNK_GID)
-        return RT_ERR_LA_TRUNK_ID;
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_PORT_TRUNK_GROUP_MASK, RTL8367C_PORT_TRUNK_GROUP0_MASK_MASK << (group * 4), portmask);
-}
-/* Function Name:
- *      rtl8367c_getAsicTrunkingGroup
- * Description:
- *      Get trunking group available port mask
- * Input:
- *      group       - Trunk Group ID
- * Output:
- *      pPortmask   - Logic trunking enable port mask, max 4 ports
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTrunkingGroup(rtk_uint32 group, rtk_uint32* pPortmask)
-{
-    if(group > RTL8367C_MAX_TRUNK_GID)
-        return RT_ERR_LA_TRUNK_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_TRUNK_GROUP_MASK, RTL8367C_PORT_TRUNK_GROUP0_MASK_MASK << (group * 4), pPortmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicTrunkingFlood
- * Description:
- *      Set port trunking flood function
- * Input:
- *      enabled     - Port trunking flooding function 0:disable 1:enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicTrunkingFlood(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_PORT_TRUNK_CTRL, RTL8367C_PORT_TRUNK_FLOOD_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicTrunkingFlood
- * Description:
- *      Get port trunking flood function
- * Input:
- *      pEnabled    - Port trunking flooding function 0:disable 1:enable
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTrunkingFlood(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_PORT_TRUNK_CTRL, RTL8367C_PORT_TRUNK_FLOOD_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicTrunkingHashSelect
- * Description:
- *      Set port trunking hash select sources
- * Input:
- *      hashsel     - hash sources mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      7 bits mask for link aggregation group0 hash parameter selection {DIP, SIP, DMAC, SMAC, SPA}
- *      0b0000001: SPA
- *      0b0000010: SMAC
- *      0b0000100: DMAC
- *      0b0001000: SIP
- *      0b0010000: DIP
- *      0b0100000: TCP/UDP Source Port
- *      0b1000000: TCP/UDP Destination Port
- */
-ret_t rtl8367c_setAsicTrunkingHashSelect(rtk_uint32 hashsel)
-{
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_PORT_TRUNK_CTRL, RTL8367C_PORT_TRUNK_HASH_MASK, hashsel);
-}
-/* Function Name:
- *      rtl8367c_getAsicTrunkingHashSelect
- * Description:
- *      Get port trunking hash select sources
- * Input:
- *      pHashsel    - hash sources mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTrunkingHashSelect(rtk_uint32* pHashsel)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_TRUNK_CTRL, RTL8367C_PORT_TRUNK_HASH_MASK, pHashsel);
-}
-/* Function Name:
- *      rtl8367c_getAsicQeueuEmptyStatus
- * Description:
- *      Get current output queue if empty status
- * Input:
- *      portmask    - queue empty port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicQeueuEmptyStatus(rtk_uint32* portmask)
-{
-    return rtl8367c_getAsicReg(RTL8367C_REG_PORT_QEMPTY, portmask);
-}
-/* Function Name:
- *      rtl8367c_setAsicTrunkingHashTable
- * Description:
- *      Set port trunking hash value mapping table
- * Input:
- *      hashval     - hashing value 0-15
- *      portId      - trunking port id 0-3
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - Invalid hashing value (0-15)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicTrunkingHashTable(rtk_uint32 hashval, rtk_uint32 portId)
-{
-    if(hashval > RTL8367C_TRUNKING_HASHVALUE_MAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(portId >= RTL8367C_TRUNKING_PORTNO)
-        return RT_ERR_PORT_ID;
-
-    if(hashval >= 8)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL1, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH8_MASK<<((hashval-8)*2), portId);
-    else
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL0, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH0_MASK<<(hashval*2), portId);
-}
-/* Function Name:
- *      rtl8367c_getAsicTrunkingHashTable
- * Description:
- *      Get port trunking hash value mapping table
- * Input:
- *      hashval     - hashing value 0-15
- *      pPortId         - trunking port id 0-3
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - Invalid hashing value (0-15)
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTrunkingHashTable(rtk_uint32 hashval, rtk_uint32* pPortId)
-{
-    if(hashval > RTL8367C_TRUNKING_HASHVALUE_MAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(hashval >= 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL1, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL1_HASH8_MASK<<((hashval-8)*2), pPortId);
-    else
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL0, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL0_HASH0_MASK<<(hashval*2), pPortId);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicTrunkingHashTable1
- * Description:
- *      Set port trunking hash value mapping table
- * Input:
- *      hashval     - hashing value 0-15
- *      portId      - trunking port id 0-3
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_OUT_OF_RANGE - Invalid hashing value (0-15)
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicTrunkingHashTable1(rtk_uint32 hashval, rtk_uint32 portId)
-{
-    if(hashval > RTL8367C_TRUNKING_HASHVALUE_MAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(portId >= RTL8367C_TRUNKING1_PORTN0)
-        return RT_ERR_PORT_ID;
-
-    if(hashval >= 8)
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL3, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH8_MASK<<((hashval-8)*2), portId);
-    else
-        return rtl8367c_setAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL2, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH0_MASK<<(hashval*2), portId);
-}
-/* Function Name:
- *      rtl8367c_getAsicTrunkingHashTable1
- * Description:
- *      Get port trunking hash value mapping table
- * Input:
- *      hashval     - hashing value 0-15
- *      pPortId         - trunking port id 0-3
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_OUT_OF_RANGE - Invalid hashing value (0-15)
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicTrunkingHashTable1(rtk_uint32 hashval, rtk_uint32* pPortId)
-{
-    if(hashval > RTL8367C_TRUNKING_HASHVALUE_MAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(hashval >= 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL3, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL3_HASH8_MASK<<((hashval-8)*2), pPortId);
-    else
-        return rtl8367c_getAsicRegBits(RTL8367C_REG_PORT_TRUNK_HASH_MAPPING_CTRL2, RTL8367C_PORT_TRUNK_HASH_MAPPING_CTRL2_HASH0_MASK<<(hashval*2), pPortId);
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_unknownMulticast.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_unknownMulticast.c
deleted file mode 100644
index fcebd1b7f7..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_unknownMulticast.c
+++ /dev/null
@@ -1,238 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : Unkown multicast related functions
- *
- */
-
-#include <rtl8367c_asicdrv_unknownMulticast.h>
-
-/* Function Name:
- *      rtl8367c_setAsicUnknownL2MulticastBehavior
- * Description:
- *      Set behavior of L2 multicast
- * Input:
- *      port    - Physical port number (0~7)
- *      behave  - 0: flooding, 1: drop, 2: trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_NOT_ALLOWED  - Invalid operation
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicUnknownL2MulticastBehavior(rtk_uint32 port, rtk_uint32 behave)
-{
-    ret_t retVal;
-
-    if(port >  RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(behave >= L2_UNKOWN_MULTICAST_END)
-        return RT_ERR_NOT_ALLOWED;
-    if(port < 8)
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_UNKNOWN_L2_MULTICAST_REG(port), RTL8367C_UNKNOWN_L2_MULTICAST_MASK(port), behave);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_UNKNOWN_L2_MULTICAST_CTRL1, 3 << ((port - 8) << 1), behave);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicUnknownL2MulticastBehavior
- * Description:
- *      Get behavior of L2 multicast
- * Input:
- *      port    - Physical port number (0~7)
- *      pBehave     - 0: flooding, 1: drop, 2: trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicUnknownL2MulticastBehavior(rtk_uint32 port, rtk_uint32 *pBehave)
-{
-    ret_t retVal;
-
-    if(port >  RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_UNKNOWN_L2_MULTICAST_REG(port), RTL8367C_UNKNOWN_L2_MULTICAST_MASK(port), pBehave);
-        if (retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_UNKNOWN_L2_MULTICAST_CTRL1, 3 << ((port - 8) << 1), pBehave);
-        if (retVal != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicUnknownIPv4MulticastBehavior
- * Description:
- *      Set behavior of IPv4 multicast
- * Input:
- *      port    - Physical port number (0~7)
- *      behave  - 0: flooding, 1: drop, 2: trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_NOT_ALLOWED  - Invalid operation
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicUnknownIPv4MulticastBehavior(rtk_uint32 port, rtk_uint32 behave)
-{
-    if(port >  RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(behave >= L3_UNKOWN_MULTICAST_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_UNKNOWN_IPV4_MULTICAST_REG(port), RTL8367C_UNKNOWN_IPV4_MULTICAST_MASK(port), behave);
-}
-/* Function Name:
- *      rtl8367c_getAsicUnknownIPv4MulticastBehavior
- * Description:
- *      Get behavior of IPv4 multicast
- * Input:
- *      port    - Physical port number (0~7)
- *      pBehave     - 0: flooding, 1: drop, 2: trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicUnknownIPv4MulticastBehavior(rtk_uint32 port, rtk_uint32 *pBehave)
-{
-    if(port >  RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_UNKNOWN_IPV4_MULTICAST_REG(port), RTL8367C_UNKNOWN_IPV4_MULTICAST_MASK(port), pBehave);
-}
-/* Function Name:
- *      rtl8367c_setAsicUnknownIPv6MulticastBehavior
- * Description:
- *      Set behavior of IPv6 multicast
- * Input:
- *      port    - Physical port number (0~7)
- *      behave  - 0: flooding, 1: drop, 2: trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_NOT_ALLOWED  - Invalid operation
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicUnknownIPv6MulticastBehavior(rtk_uint32 port, rtk_uint32 behave)
-{
-    if(port >  RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(behave >= L3_UNKOWN_MULTICAST_END)
-        return RT_ERR_NOT_ALLOWED;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_UNKNOWN_IPV6_MULTICAST_REG(port), RTL8367C_UNKNOWN_IPV6_MULTICAST_MASK(port), behave);
-}
-/* Function Name:
- *      rtl8367c_getAsicUnknownIPv6MulticastBehavior
- * Description:
- *      Get behavior of IPv6 multicast
- * Input:
- *      port    - Physical port number (0~7)
- *      pBehave     - 0: flooding, 1: drop, 2: trap
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicUnknownIPv6MulticastBehavior(rtk_uint32 port, rtk_uint32 *pBehave)
-{
-    if(port >  RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_UNKNOWN_IPV6_MULTICAST_REG(port), RTL8367C_UNKNOWN_IPV6_MULTICAST_MASK(port), pBehave);
-}
-/* Function Name:
- *      rtl8367c_setAsicUnknownMulticastTrapPriority
- * Description:
- *      Set trap priority of unknown multicast frame
- * Input:
- *      priority    - priority (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_QOS_INT_PRIORITY - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicUnknownMulticastTrapPriority(rtk_uint32 priority)
-{
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_QOS_TRAP_PRIORITY_CTRL0_REG, RTL8367C_UNKNOWN_MC_PRIORTY_MASK, priority);
-}
-/* Function Name:
- *      rtl8367c_getAsicUnknownMulticastTrapPriority
- * Description:
- *      Get trap priority of unknown multicast frame
- * Input:
- *      pPriority   - priority (0~7)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK   - Success
- *      RT_ERR_SMI  - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicUnknownMulticastTrapPriority(rtk_uint32 *pPriority)
-{
-    return rtl8367c_getAsicRegBits(RTL8367C_QOS_TRAP_PRIORITY_CTRL0_REG, RTL8367C_UNKNOWN_MC_PRIORTY_MASK, pPriority);
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_vlan.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_vlan.c
deleted file mode 100644
index 1e283e7432..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/rtl8367c_asicdrv_vlan.c
+++ /dev/null
@@ -1,1505 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTL8367C switch high-level API for RTL8367C
- * Feature : VLAN related functions
- *
- */
-#include <rtl8367c_asicdrv_vlan.h>
-
-#include <string.h>
-
-#if defined(CONFIG_RTL8367C_ASICDRV_TEST)
-rtl8367c_user_vlan4kentry Rtl8370sVirtualVlanTable[RTL8367C_VIDMAX + 1];
-#endif
-
-static void _rtl8367c_VlanMCStUser2Smi(rtl8367c_vlanconfiguser *pVlanCg, rtk_uint16 *pSmiVlanCfg)
-{
-    pSmiVlanCfg[0] |= pVlanCg->mbr & 0x07FF;
-
-    pSmiVlanCfg[1] |= pVlanCg->fid_msti & 0x000F;
-
-    pSmiVlanCfg[2] |= pVlanCg->vbpen & 0x0001;
-    pSmiVlanCfg[2] |= (pVlanCg->vbpri & 0x0007) << 1;
-    pSmiVlanCfg[2] |= (pVlanCg->envlanpol & 0x0001) << 4;
-    pSmiVlanCfg[2] |= (pVlanCg->meteridx & 0x003F) << 5;
-
-    pSmiVlanCfg[3] |= pVlanCg->evid & 0x1FFF;
-}
-
-static void _rtl8367c_VlanMCStSmi2User(rtk_uint16 *pSmiVlanCfg, rtl8367c_vlanconfiguser *pVlanCg)
-{
-    pVlanCg->mbr            = pSmiVlanCfg[0] & 0x07FF;
-    pVlanCg->fid_msti       = pSmiVlanCfg[1] & 0x000F;
-    pVlanCg->meteridx       = (pSmiVlanCfg[2] >> 5) & 0x003F;
-    pVlanCg->envlanpol      = (pSmiVlanCfg[2] >> 4) & 0x0001;
-    pVlanCg->vbpri          = (pSmiVlanCfg[2] >> 1) & 0x0007;
-    pVlanCg->vbpen          = pSmiVlanCfg[2] & 0x0001;
-    pVlanCg->evid           = pSmiVlanCfg[3] & 0x1FFF;
-}
-
-static void _rtl8367c_Vlan4kStUser2Smi(rtl8367c_user_vlan4kentry *pUserVlan4kEntry, rtk_uint16 *pSmiVlan4kEntry)
-{
-    pSmiVlan4kEntry[0] |= (pUserVlan4kEntry->mbr & 0x00FF);
-    pSmiVlan4kEntry[0] |= (pUserVlan4kEntry->untag & 0x00FF) << 8;
-
-    pSmiVlan4kEntry[1] |= (pUserVlan4kEntry->fid_msti & 0x000F);
-    pSmiVlan4kEntry[1] |= (pUserVlan4kEntry->vbpen & 0x0001) << 4;
-    pSmiVlan4kEntry[1] |= (pUserVlan4kEntry->vbpri & 0x0007) << 5;
-    pSmiVlan4kEntry[1] |= (pUserVlan4kEntry->envlanpol & 0x0001) << 8;
-    pSmiVlan4kEntry[1] |= (pUserVlan4kEntry->meteridx & 0x001F) << 9;
-    pSmiVlan4kEntry[1] |= (pUserVlan4kEntry->ivl_svl & 0x0001) << 14;
-
-    pSmiVlan4kEntry[2] |= ((pUserVlan4kEntry->mbr & 0x0700) >> 8);
-    pSmiVlan4kEntry[2] |= ((pUserVlan4kEntry->untag & 0x0700) >> 8) << 3;
-    pSmiVlan4kEntry[2] |= ((pUserVlan4kEntry->meteridx & 0x0020) >> 5) << 6;
-}
-
-
-static void _rtl8367c_Vlan4kStSmi2User(rtk_uint16 *pSmiVlan4kEntry, rtl8367c_user_vlan4kentry *pUserVlan4kEntry)
-{
-    pUserVlan4kEntry->mbr = (pSmiVlan4kEntry[0] & 0x00FF) | ((pSmiVlan4kEntry[2] & 0x0007) << 8);
-    pUserVlan4kEntry->untag = ((pSmiVlan4kEntry[0] & 0xFF00) >> 8) | (((pSmiVlan4kEntry[2] & 0x0038) >> 3) << 8);
-    pUserVlan4kEntry->fid_msti = pSmiVlan4kEntry[1] & 0x000F;
-    pUserVlan4kEntry->vbpen = (pSmiVlan4kEntry[1] & 0x0010) >> 4;
-    pUserVlan4kEntry->vbpri = (pSmiVlan4kEntry[1] & 0x00E0) >> 5;
-    pUserVlan4kEntry->envlanpol = (pSmiVlan4kEntry[1] & 0x0100) >> 8;
-    pUserVlan4kEntry->meteridx = ((pSmiVlan4kEntry[1] & 0x3E00) >> 9) | (((pSmiVlan4kEntry[2] & 0x0040) >> 6) << 5);
-    pUserVlan4kEntry->ivl_svl = (pSmiVlan4kEntry[1] & 0x4000) >> 14;
-}
-
-/* Function Name:
- *      rtl8367c_setAsicVlanMemberConfig
- * Description:
- *      Set 32 VLAN member configurations
- * Input:
- *      index       - VLAN member configuration index (0~31)
- *      pVlanCg - VLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter
- *      RT_ERR_L2_FID               - Invalid FID
- *      RT_ERR_PORT_MASK            - Invalid portmask
- *      RT_ERR_FILTER_METER_ID      - Invalid meter
- *      RT_ERR_QOS_INT_PRIORITY     - Invalid priority
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - Invalid VLAN member configuration index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanMemberConfig(rtk_uint32 index, rtl8367c_vlanconfiguser *pVlanCg)
-{
-    ret_t  retVal;
-    rtk_uint32 regAddr;
-    rtk_uint32 regData;
-    rtk_uint16 *tableAddr;
-    rtk_uint32 page_idx;
-    rtk_uint16 smi_vlancfg[RTL8367C_VLAN_MBRCFG_LEN];
-
-    /* Error Checking  */
-    if(index > RTL8367C_CVIDXMAX)
-        return RT_ERR_VLAN_ENTRY_NOT_FOUND;
-
-    if(pVlanCg->evid > RTL8367C_EVIDMAX)
-        return RT_ERR_INPUT;
-
-
-    if(pVlanCg->mbr > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    if(pVlanCg->fid_msti > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    if(pVlanCg->meteridx > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(pVlanCg->vbpri > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    memset(smi_vlancfg, 0x00, sizeof(rtk_uint16) * RTL8367C_VLAN_MBRCFG_LEN);
-    _rtl8367c_VlanMCStUser2Smi(pVlanCg, smi_vlancfg);
-    tableAddr = smi_vlancfg;
-
-    for(page_idx = 0; page_idx < 4; page_idx++)  /* 4 pages per VLAN Member Config */
-    {
-        regAddr = RTL8367C_VLAN_MEMBER_CONFIGURATION_BASE + (index * 4) + page_idx;
-        regData = *tableAddr;
-
-        retVal = rtl8367c_setAsicReg(regAddr, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        tableAddr++;
-    }
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanMemberConfig
- * Description:
- *      Get 32 VLAN member configurations
- * Input:
- *      index       - VLAN member configuration index (0~31)
- *      pVlanCg - VLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - Invalid VLAN member configuration index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanMemberConfig(rtk_uint32 index, rtl8367c_vlanconfiguser *pVlanCg)
-{
-    ret_t  retVal;
-    rtk_uint32 page_idx;
-    rtk_uint32 regAddr;
-    rtk_uint32 regData;
-    rtk_uint16 *tableAddr;
-    rtk_uint16 smi_vlancfg[RTL8367C_VLAN_MBRCFG_LEN];
-
-    if(index > RTL8367C_CVIDXMAX)
-        return RT_ERR_VLAN_ENTRY_NOT_FOUND;
-
-    memset(smi_vlancfg, 0x00, sizeof(rtk_uint16) * RTL8367C_VLAN_MBRCFG_LEN);
-    tableAddr  = smi_vlancfg;
-
-    for(page_idx = 0; page_idx < 4; page_idx++)  /* 4 pages per VLAN Member Config */
-    {
-        regAddr = RTL8367C_VLAN_MEMBER_CONFIGURATION_BASE + (index * 4) + page_idx;
-
-        retVal = rtl8367c_getAsicReg(regAddr, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *tableAddr = (rtk_uint16)regData;
-        tableAddr++;
-    }
-
-    _rtl8367c_VlanMCStSmi2User(smi_vlancfg, pVlanCg);
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicVlan4kEntry
- * Description:
- *      Set VID mapped entry to 4K VLAN table
- * Input:
- *      pVlan4kEntry - 4K VLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter
- *      RT_ERR_L2_FID               - Invalid FID
- *      RT_ERR_VLAN_VID             - Invalid VID parameter (0~4095)
- *      RT_ERR_PORT_MASK            - Invalid portmask
- *      RT_ERR_FILTER_METER_ID      - Invalid meter
- *      RT_ERR_QOS_INT_PRIORITY     - Invalid priority
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlan4kEntry(rtl8367c_user_vlan4kentry *pVlan4kEntry )
-{
-    rtk_uint16              vlan_4k_entry[RTL8367C_VLAN_4KTABLE_LEN];
-    rtk_uint32                  page_idx;
-    rtk_uint16                  *tableAddr;
-    ret_t                   retVal;
-    rtk_uint32                  regData;
-
-    if(pVlan4kEntry->vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    if(pVlan4kEntry->mbr > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    if(pVlan4kEntry->untag > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    if(pVlan4kEntry->fid_msti > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    if(pVlan4kEntry->meteridx > RTL8367C_METERMAX)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(pVlan4kEntry->vbpri > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    memset(vlan_4k_entry, 0x00, sizeof(rtk_uint16) * RTL8367C_VLAN_4KTABLE_LEN);
-    _rtl8367c_Vlan4kStUser2Smi(pVlan4kEntry, vlan_4k_entry);
-
-    /* Prepare Data */
-    tableAddr = vlan_4k_entry;
-    for(page_idx = 0; page_idx < RTL8367C_VLAN_4KTABLE_LEN; page_idx++)
-    {
-        regData = *tableAddr;
-        retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_WRDATA_BASE + page_idx, regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        tableAddr++;
-    }
-
-    /* Write Address (VLAN_ID) */
-    regData = pVlan4kEntry->vid;
-    retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_ADDR_REG, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Write Command */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_TABLE_ACCESS_CTRL_REG, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK,RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_WRITE,TB_TARGET_CVLAN));
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-#if defined(CONFIG_RTL8367C_ASICDRV_TEST)
-    memcpy(&Rtl8370sVirtualVlanTable[pVlan4kEntry->vid], pVlan4kEntry, sizeof(rtl8367c_user_vlan4kentry));
-#endif
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicVlan4kEntry
- * Description:
- *      Get VID mapped entry to 4K VLAN table
- * Input:
- *      pVlan4kEntry - 4K VLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - Success
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_VLAN_VID         - Invalid VID parameter (0~4095)
- *      RT_ERR_BUSYWAIT_TIMEOUT - LUT is busy at retrieving
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlan4kEntry(rtl8367c_user_vlan4kentry *pVlan4kEntry )
-{
-    rtk_uint16                  vlan_4k_entry[RTL8367C_VLAN_4KTABLE_LEN];
-    rtk_uint32                  page_idx;
-    rtk_uint16                  *tableAddr;
-    ret_t                       retVal;
-    rtk_uint32                  regData;
-    rtk_uint32                  busyCounter;
-
-    if(pVlan4kEntry->vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Polling status */
-    busyCounter = RTL8367C_VLAN_BUSY_CHECK_NO;
-    while(busyCounter)
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_OFFSET,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        if(regData == 0)
-            break;
-
-        busyCounter --;
-        if(busyCounter == 0)
-            return RT_ERR_BUSYWAIT_TIMEOUT;
-    }
-
-    /* Write Address (VLAN_ID) */
-    regData = pVlan4kEntry->vid;
-    retVal = rtl8367c_setAsicReg(RTL8367C_TABLE_ACCESS_ADDR_REG, regData);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Read Command */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_TABLE_ACCESS_CTRL_REG, RTL8367C_TABLE_TYPE_MASK | RTL8367C_COMMAND_TYPE_MASK, RTL8367C_TABLE_ACCESS_REG_DATA(TB_OP_READ,TB_TARGET_CVLAN));
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Polling status */
-    busyCounter = RTL8367C_VLAN_BUSY_CHECK_NO;
-    while(busyCounter)
-    {
-        retVal = rtl8367c_getAsicRegBit(RTL8367C_TABLE_ACCESS_STATUS_REG, RTL8367C_TABLE_LUT_ADDR_BUSY_FLAG_OFFSET,&regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        if(regData == 0)
-            break;
-
-        busyCounter --;
-        if(busyCounter == 0)
-            return RT_ERR_BUSYWAIT_TIMEOUT;
-    }
-
-    /* Read VLAN data from register */
-    tableAddr = vlan_4k_entry;
-    for(page_idx = 0; page_idx < RTL8367C_VLAN_4KTABLE_LEN; page_idx++)
-    {
-        retVal = rtl8367c_getAsicReg(RTL8367C_TABLE_ACCESS_RDDATA_BASE + page_idx, &regData);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-
-        *tableAddr = regData;
-        tableAddr++;
-    }
-
-    _rtl8367c_Vlan4kStSmi2User(vlan_4k_entry, pVlan4kEntry);
-
-#if defined(CONFIG_RTL8367C_ASICDRV_TEST)
-    memcpy(pVlan4kEntry, &Rtl8370sVirtualVlanTable[pVlan4kEntry->vid], sizeof(rtl8367c_user_vlan4kentry));
-#endif
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanAccpetFrameType
- * Description:
- *      Set per-port acceptable frame type
- * Input:
- *      port        - Physical port number (0~10)
- *      frameType   - The acceptable frame type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - Success
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_PORT_ID                  - Invalid port number
- *      RT_ERR_VLAN_ACCEPT_FRAME_TYPE   - Invalid frame type
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanAccpetFrameType(rtk_uint32 port, rtl8367c_accframetype frameType)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(frameType >= FRAME_TYPE_MAX_BOUND)
-        return RT_ERR_VLAN_ACCEPT_FRAME_TYPE;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_VLAN_ACCEPT_FRAME_TYPE_REG(port), RTL8367C_VLAN_ACCEPT_FRAME_TYPE_MASK(port), frameType);
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanAccpetFrameType
- * Description:
- *      Get per-port acceptable frame type
- * Input:
- *      port        - Physical port number (0~10)
- *      pFrameType  - The acceptable frame type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - Success
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_PORT_ID                  - Invalid port number
- *      RT_ERR_VLAN_ACCEPT_FRAME_TYPE   - Invalid frame type
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanAccpetFrameType(rtk_uint32 port, rtl8367c_accframetype *pFrameType)
-{
-    rtk_uint32 regData;
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if((retVal = rtl8367c_getAsicRegBits(RTL8367C_VLAN_ACCEPT_FRAME_TYPE_REG(port), RTL8367C_VLAN_ACCEPT_FRAME_TYPE_MASK(port), &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pFrameType = (rtl8367c_accframetype)regData;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanIngressFilter
- * Description:
- *      Set VLAN Ingress Filter
- * Input:
- *      port        - Physical port number (0~10)
- *      enabled     - Enable or disable Ingress filter
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanIngressFilter(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_VLAN_INGRESS_REG, port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanIngressFilter
- * Description:
- *      Get VLAN Ingress Filter
- * Input:
- *      port        - Physical port number (0~10)
- *      pEnable     - Enable or disable Ingress filter
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanIngressFilter(rtk_uint32 port, rtk_uint32 *pEnable)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_VLAN_INGRESS_REG, port, pEnable);
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanEgressTagMode
- * Description:
- *      Set CVLAN egress tag mode
- * Input:
- *      port        - Physical port number (0~10)
- *      tagMode     - The egress tag mode. Including Original mode, Keep tag mode and Priority tag mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Invalid input parameter
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanEgressTagMode(rtk_uint32 port, rtl8367c_egtagmode tagMode)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(tagMode >= EG_TAG_MODE_END)
-        return RT_ERR_INPUT;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_PORT_MISC_CFG_REG(port), RTL8367C_VLAN_EGRESS_MDOE_MASK, tagMode);
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanEgressTagMode
- * Description:
- *      Get CVLAN egress tag mode
- * Input:
- *      port        - Physical port number (0~10)
- *      pTagMode    - The egress tag mode. Including Original mode, Keep tag mode and Priority tag mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanEgressTagMode(rtk_uint32 port, rtl8367c_egtagmode *pTagMode)
-{
-    rtk_uint32 regData;
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if((retVal = rtl8367c_getAsicRegBits(RTL8367C_PORT_MISC_CFG_REG(port), RTL8367C_VLAN_EGRESS_MDOE_MASK, &regData)) != RT_ERR_OK)
-        return retVal;
-
-    *pTagMode = (rtl8367c_egtagmode)regData;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanPortBasedVID
- * Description:
- *      Set port based VID which is indexed to 32 VLAN member configurations
- * Input:
- *      port    - Physical port number (0~10)
- *      index   - Index to VLAN member configuration
- *      pri     - 1Q Port based VLAN priority
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number
- *      RT_ERR_QOS_INT_PRIORITY     - Invalid priority
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - Invalid VLAN member configuration index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanPortBasedVID(rtk_uint32 port, rtk_uint32 index, rtk_uint32 pri)
-{
-    rtk_uint32 regAddr, bit_mask;
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(index > RTL8367C_CVIDXMAX)
-        return RT_ERR_VLAN_ENTRY_NOT_FOUND;
-
-    if(pri > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    regAddr = RTL8367C_VLAN_PVID_CTRL_REG(port);
-    bit_mask = RTL8367C_PORT_VIDX_MASK(port);
-    retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, index);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_VLAN_PORTBASED_PRIORITY_REG(port);
-    bit_mask = RTL8367C_VLAN_PORTBASED_PRIORITY_MASK(port);
-    retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, pri);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanPortBasedVID
- * Description:
- *      Get port based VID which is indexed to 32 VLAN member configurations
- * Input:
- *      port    - Physical port number (0~10)
- *      pIndex  - Index to VLAN member configuration
- *      pPri    - 1Q Port based VLAN priority
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanPortBasedVID(rtk_uint32 port, rtk_uint32 *pIndex, rtk_uint32 *pPri)
-{
-    rtk_uint32 regAddr,bit_mask;
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    regAddr = RTL8367C_VLAN_PVID_CTRL_REG(port);
-    bit_mask = RTL8367C_PORT_VIDX_MASK(port);
-    retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, pIndex);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    regAddr = RTL8367C_VLAN_PORTBASED_PRIORITY_REG(port);
-    bit_mask = RTL8367C_VLAN_PORTBASED_PRIORITY_MASK(port);
-    retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, pPri);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanProtocolBasedGroupData
- * Description:
- *      Set protocol and port based group database
- * Input:
- *      index       - Index to VLAN member configuration
- *      pPbCfg  - Protocol and port based group database entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter
- *      RT_ERR_VLAN_PROTO_AND_PORT  - Invalid protocol base group database index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanProtocolBasedGroupData(rtk_uint32 index, rtl8367c_protocolgdatacfg *pPbCfg)
-{
-    rtk_uint32  frameType;
-    rtk_uint32  etherType;
-    ret_t   retVal;
-
-    /* Error Checking */
-    if(index > RTL8367C_PROTOVLAN_GIDX_MAX)
-        return RT_ERR_VLAN_PROTO_AND_PORT;
-
-    if(pPbCfg->frameType >= PPVLAN_FRAME_TYPE_END )
-        return RT_ERR_INPUT;
-
-    frameType = pPbCfg->frameType;
-    etherType = pPbCfg->etherType;
-
-    /* Frame type */
-    retVal = rtl8367c_setAsicRegBits(RTL8367C_VLAN_PPB_FRAMETYPE_REG(index), RTL8367C_VLAN_PPB_FRAMETYPE_MASK, frameType);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Ether type */
-    retVal = rtl8367c_setAsicReg(RTL8367C_VLAN_PPB_ETHERTYPR_REG(index), etherType);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanProtocolBasedGroupData
- * Description:
- *      Get protocol and port based group database
- * Input:
- *      index       - Index to VLAN member configuration
- *      pPbCfg  - Protocol and port based group database entry
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter
- *      RT_ERR_VLAN_PROTO_AND_PORT  - Invalid protocol base group database index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanProtocolBasedGroupData(rtk_uint32 index, rtl8367c_protocolgdatacfg *pPbCfg)
-{
-    rtk_uint32  frameType;
-    rtk_uint32  etherType;
-    ret_t   retVal;
-
-    /* Error Checking */
-    if(index > RTL8367C_PROTOVLAN_GIDX_MAX)
-        return RT_ERR_VLAN_PROTO_AND_PORT;
-
-    /* Read Frame type */
-    retVal = rtl8367c_getAsicRegBits(RTL8367C_VLAN_PPB_FRAMETYPE_REG(index), RTL8367C_VLAN_PPB_FRAMETYPE_MASK, &frameType);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Read Ether type */
-    retVal = rtl8367c_getAsicReg(RTL8367C_VLAN_PPB_ETHERTYPR_REG(index), &etherType);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-
-    pPbCfg->frameType = frameType;
-    pPbCfg->etherType = etherType;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanPortAndProtocolBased
- * Description:
- *      Set protocol and port based VLAN configuration
- * Input:
- *      port        - Physical port number (0~10)
- *      index       - Index of protocol and port based database index
- *      pPpbCfg     - Protocol and port based VLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter
- *      RT_ERR_PORT_ID              - Invalid port number
- *      RT_ERR_QOS_INT_PRIORITY     - Invalid priority
- *      RT_ERR_VLAN_PROTO_AND_PORT  - Invalid protocol base group database index
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - Invalid VLAN member configuration index
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanPortAndProtocolBased(rtk_uint32 port, rtk_uint32 index, rtl8367c_protocolvlancfg *pPpbCfg)
-{
-    rtk_uint32  reg_addr, bit_mask, bit_value;
-    ret_t   retVal;
-
-    /* Error Checking */
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(index > RTL8367C_PROTOVLAN_GIDX_MAX)
-        return RT_ERR_VLAN_PROTO_AND_PORT;
-
-    if( (pPpbCfg->valid != FALSE) && (pPpbCfg->valid != TRUE) )
-        return RT_ERR_INPUT;
-
-    if(pPpbCfg->vlan_idx > RTL8367C_CVIDXMAX)
-        return RT_ERR_VLAN_ENTRY_NOT_FOUND;
-
-    if(pPpbCfg->priority > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    /* Valid bit */
-    reg_addr  = RTL8367C_VLAN_PPB_VALID_REG(index);
-    bit_mask  = 0x0001 << port;
-    bit_value = ((TRUE == pPpbCfg->valid) ? 0x1 : 0x0);
-    retVal    = rtl8367c_setAsicRegBits(reg_addr, bit_mask, bit_value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* Calculate the actual register address for CVLAN index*/
-    if(port < 8)
-    {
-        reg_addr = RTL8367C_VLAN_PPB_CTRL_REG(index, port);
-        bit_mask = RTL8367C_VLAN_PPB_CTRL_MASK(port);
-    }
-    else if(port == 8)
-    {
-        reg_addr = RTL8367C_REG_VLAN_PPB0_CTRL4;
-        bit_mask = RTL8367C_VLAN_PPB0_CTRL4_PORT8_INDEX_MASK;
-    }
-    else if(port == 9)
-    {
-        reg_addr = RTL8367C_REG_VLAN_PPB0_CTRL4;
-        bit_mask = RTL8367C_VLAN_PPB0_CTRL4_PORT9_INDEX_MASK;
-    }
-    else if(port == 10)
-    {
-        reg_addr = RTL8367C_REG_VLAN_PPB0_CTRL4;
-        bit_mask = RTL8367C_VLAN_PPB0_CTRL4_PORT10_INDEX_MASK;
-    }
-
-    bit_value = pPpbCfg->vlan_idx;
-    retVal  = rtl8367c_setAsicRegBits(reg_addr, bit_mask, bit_value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    /* write priority */
-    reg_addr  = RTL8367C_VLAN_PPB_PRIORITY_ITEM_REG(port, index);
-    bit_mask  = RTL8367C_VLAN_PPB_PRIORITY_ITEM_MASK(port);
-    bit_value = pPpbCfg->priority;
-    retVal    = rtl8367c_setAsicRegBits(reg_addr, bit_mask, bit_value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanPortAndProtocolBased
- * Description:
- *      Get protocol and port based VLAN configuration
- * Input:
- *      port        - Physical port number (0~7)
- *      index       - Index of protocol and port based database index
- *      pPpbCfg     - Protocol and port based VLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - Success
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameter
- *      RT_ERR_PORT_ID              - Invalid port number
- *      RT_ERR_VLAN_PROTO_AND_PORT  - Invalid protocol base group database index
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanPortAndProtocolBased(rtk_uint32 port, rtk_uint32 index, rtl8367c_protocolvlancfg *pPpbCfg)
-{
-    rtk_uint32  reg_addr, bit_mask, bit_value;
-    ret_t   retVal;
-
-    /* Error Checking */
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(index > RTL8367C_PROTOVLAN_GIDX_MAX)
-        return RT_ERR_VLAN_PROTO_AND_PORT;
-
-    if(pPpbCfg == NULL)
-        return RT_ERR_INPUT;
-
-    /* Valid bit */
-    reg_addr  = RTL8367C_VLAN_PPB_VALID_REG(index);
-    bit_mask  = 0x0001 << port;
-    retVal    = rtl8367c_getAsicRegBits(reg_addr, bit_mask, &bit_value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pPpbCfg->valid = bit_value;
-
-    /* CVLAN index */
-    if(port < 8)
-    {
-        reg_addr = RTL8367C_VLAN_PPB_CTRL_REG(index, port);
-        bit_mask = RTL8367C_VLAN_PPB_CTRL_MASK(port);
-    }
-    else if(port == 8)
-    {
-        reg_addr = RTL8367C_REG_VLAN_PPB0_CTRL4;
-        bit_mask = RTL8367C_VLAN_PPB0_CTRL4_PORT8_INDEX_MASK;
-    }
-    else if(port == 9)
-    {
-        reg_addr = RTL8367C_REG_VLAN_PPB0_CTRL4;
-        bit_mask = RTL8367C_VLAN_PPB0_CTRL4_PORT9_INDEX_MASK;
-    }
-    else if(port == 10)
-    {
-        reg_addr = RTL8367C_REG_VLAN_PPB0_CTRL4;
-        bit_mask = RTL8367C_VLAN_PPB0_CTRL4_PORT10_INDEX_MASK;
-    }
-
-    retVal = rtl8367c_getAsicRegBits(reg_addr, bit_mask, &bit_value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pPpbCfg->vlan_idx = bit_value;
-
-
-    /* priority */
-    reg_addr = RTL8367C_VLAN_PPB_PRIORITY_ITEM_REG(port,index);
-    bit_mask = RTL8367C_VLAN_PPB_PRIORITY_ITEM_MASK(port);
-    retVal = rtl8367c_getAsicRegBits(reg_addr, bit_mask, &bit_value);
-    if(retVal != RT_ERR_OK)
-        return retVal;
-
-    pPpbCfg->priority = bit_value;
-    return RT_ERR_OK;
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanFilter
- * Description:
- *      Set enable CVLAN filtering function
- * Input:
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanFilter(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_VLAN_CTRL, RTL8367C_VLAN_CTRL_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanFilter
- * Description:
- *      Get enable CVLAN filtering function
- * Input:
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanFilter(rtk_uint32* pEnabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_VLAN_CTRL, RTL8367C_VLAN_CTRL_OFFSET, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicVlanUntagDscpPriorityEn
- * Description:
- *      Set enable Dscp to untag 1Q priority
- * Input:
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanUntagDscpPriorityEn(rtk_uint32 enabled)
-{
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_UNTAG_DSCP_PRI_CFG, RTL8367C_UNTAG_DSCP_PRI_CFG_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicVlanUntagDscpPriorityEn
- * Description:
- *      Get enable Dscp to untag 1Q priority
- * Input:
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanUntagDscpPriorityEn(rtk_uint32* enabled)
-{
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_UNTAG_DSCP_PRI_CFG, RTL8367C_UNTAG_DSCP_PRI_CFG_OFFSET, enabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicPortBasedFid
- * Description:
- *      Set port based FID
- * Input:
- *      port    - Physical port number (0~10)
- *      fid     - Port based fid
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_L2_FID   - Invalid FID
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortBasedFid(rtk_uint32 port, rtk_uint32 fid)
-{
-    rtk_uint32  reg_addr;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(fid > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    if(port < 8)
-        return rtl8367c_setAsicReg(RTL8367C_PORT_PBFID_REG(port),fid);
-    else {
-        reg_addr = RTL8367C_REG_PORT8_PBFID + port-8;
-        return rtl8367c_setAsicReg(reg_addr, fid);
-    }
-
-}
-/* Function Name:
- *      rtl8367c_getAsicPortBasedFid
- * Description:
- *      Get port based FID
- * Input:
- *      port    - Physical port number (0~7)
- *      pFid    - Port based fid
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortBasedFid(rtk_uint32 port, rtk_uint32* pFid)
-{
-    rtk_uint32  reg_addr;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8)
-        return rtl8367c_getAsicReg(RTL8367C_PORT_PBFID_REG(port), pFid);
-    else{
-        reg_addr = RTL8367C_REG_PORT8_PBFID + port-8;
-        return rtl8367c_getAsicReg(reg_addr, pFid);
-    }
-}
-/* Function Name:
- *      rtl8367c_setAsicPortBasedFidEn
- * Description:
- *      Set port based FID selection enable
- * Input:
- *      port    - Physical port number (0~10)
- *      enabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicPortBasedFidEn(rtk_uint32 port, rtk_uint32 enabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_setAsicRegBit(RTL8367C_REG_PORT_PBFIDEN,port, enabled);
-}
-/* Function Name:
- *      rtl8367c_getAsicPortBasedFidEn
- * Description:
- *      Get port based FID selection enable
- * Input:
- *      port    - Physical port number (0~10)
- *      pEnabled - 1: enabled, 0: disabled
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicPortBasedFidEn(rtk_uint32 port, rtk_uint32* pEnabled)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBit(RTL8367C_REG_PORT_PBFIDEN,port, pEnabled);
-}
-/* Function Name:
- *      rtl8367c_setAsicSpanningTreeStatus
- * Description:
- *      Set spanning tree state per each port
- * Input:
- *      port    - Physical port number (0~10)
- *      msti    - Multiple spanning tree instance
- *      state   - Spanning tree state for msti
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_MSTI         - Invalid msti parameter
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_MSTP_STATE   - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicSpanningTreeStatus(rtk_uint32 port, rtk_uint32 msti, rtk_uint32 state)
-{
-    rtk_uint32  reg_addr,bits_msk;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(msti > RTL8367C_MSTIMAX)
-        return RT_ERR_MSTI;
-
-    if(state > STPST_FORWARDING)
-        return RT_ERR_MSTP_STATE;
-
-    if(port < 8)
-        return rtl8367c_setAsicRegBits(RTL8367C_VLAN_MSTI_REG(msti,port), RTL8367C_VLAN_MSTI_MASK(port),state);
-    else{
-        reg_addr = RTL8367C_VLAN_MSTI_REG(msti,port);
-        switch(port){
-            case 8: bits_msk = RTL8367C_VLAN_MSTI0_CTRL1_PORT8_STATE_MASK;break;
-            case 9: bits_msk = RTL8367C_VLAN_MSTI0_CTRL1_PORT9_STATE_MASK;break;
-            case 10: bits_msk = RTL8367C_VLAN_MSTI0_CTRL1_PORT10_STATE_MASK;break;
-        }
-        return rtl8367c_setAsicRegBits(reg_addr, bits_msk,state);
-    }
-}
-/* Function Name:
- *      rtl8367c_getAsicSpanningTreeStatus
- * Description:
- *      Set spanning tree state per each port
- * Input:
- *      port    - Physical port number (0~10)
- *      msti    - Multiple spanning tree instance
- *      pState  - Spanning tree state for msti
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_MSTI         - Invalid msti parameter
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicSpanningTreeStatus(rtk_uint32 port, rtk_uint32 msti, rtk_uint32* pState)
-{
-    rtk_uint32  reg_addr,bits_msk;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(msti > RTL8367C_MSTIMAX)
-        return RT_ERR_MSTI;
-
-    if(port < 8)
-        return rtl8367c_getAsicRegBits(RTL8367C_VLAN_MSTI_REG(msti,port), RTL8367C_VLAN_MSTI_MASK(port), pState);
-    else{
-        reg_addr = RTL8367C_VLAN_MSTI_REG(msti,port);
-        switch(port){
-            case 8: bits_msk = RTL8367C_VLAN_MSTI0_CTRL1_PORT8_STATE_MASK;break;
-            case 9: bits_msk = RTL8367C_VLAN_MSTI0_CTRL1_PORT9_STATE_MASK;break;
-            case 10: bits_msk = RTL8367C_VLAN_MSTI0_CTRL1_PORT10_STATE_MASK;break;
-        }
-        return rtl8367c_getAsicRegBits(reg_addr, bits_msk, pState);
-    }
-
-}
-
-/* Function Name:
- *      rtl8367c_setAsicVlanTransparent
- * Description:
- *      Set VLAN transparent
- * Input:
- *      port        - Physical port number (0~10)
- *      portmask    - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanTransparent(rtk_uint32 port, rtk_uint32 portmask)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    return rtl8367c_setAsicRegBits(RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL0 + port, RTL8367C_VLAN_EGRESS_TRANS_CTRL0_MASK, portmask);
-}
-
-/* Function Name:
- *      rtl8367c_getAsicVlanTransparent
- * Description:
- *      Get VLAN transparent
- * Input:
- *      port        - Physical port number (0~10)
- * Output:
- *      pPortmask   - Ingress port mask
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanTransparent(rtk_uint32 port, rtk_uint32 *pPortmask)
-{
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    return rtl8367c_getAsicRegBits(RTL8367C_REG_VLAN_EGRESS_TRANS_CTRL0 + port, RTL8367C_VLAN_EGRESS_TRANS_CTRL0_MASK, pPortmask);
-}
-
-/* Function Name:
- *      rtl8367c_setAsicVlanEgressKeep
- * Description:
- *      Set per egress port VLAN keep mode
- * Input:
- *      port        - Physical port number (0~10)
- *      portmask    - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_MASK    - Invalid portmask
- *      RT_ERR_PORT_ID      - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_setAsicVlanEgressKeep(rtk_uint32 port, rtk_uint32 portmask)
-{
-    rtk_uint32 regAddr, bit_mask;
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(portmask > RTL8367C_PORTMASK)
-        return RT_ERR_PORT_MASK;
-
-    if(port < 8){
-        retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL0 + (port>>1),RTL8367C_PORT0_VLAN_KEEP_MASK_MASK<<((port&1)*8),portmask & 0xff);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-        regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL0_EXT + (port>>1);
-        bit_mask = RTL8367C_PORT0_VLAN_KEEP_MASK_EXT_MASK;
-        bit_mask <<= (port&1)*3;
-        retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, (portmask>>8)&0x7);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-    }
-    else{
-        switch(port){
-            case 8:
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4;
-                bit_mask = RTL8367C_PORT8_VLAN_KEEP_MASK_MASK;
-                retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, portmask & 0xff);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4_EXT;
-                bit_mask = RTL8367C_PORT8_VLAN_KEEP_MASK_EXT_MASK;
-                retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, (portmask>>8)&0x7);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                break;
-
-            case 9:
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4;
-                bit_mask = RTL8367C_PORT9_VLAN_KEEP_MASK_MASK;
-                retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, portmask & 0xff);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4_EXT;
-                bit_mask = RTL8367C_PORT9_VLAN_KEEP_MASK_EXT_MASK;
-                retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, (portmask>>8)&0x7);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                break;
-
-            case 10:
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL5;
-                bit_mask = RTL8367C_VLAN_EGRESS_KEEP_CTRL5_MASK;
-                retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, portmask & 0xff);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL5_EXT;
-                bit_mask = RTL8367C_VLAN_EGRESS_KEEP_CTRL5_EXT_MASK;
-                retVal = rtl8367c_setAsicRegBits(regAddr, bit_mask, (portmask>>8)&0x7);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                break;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getAsicVlanEgressKeep
- * Description:
- *      Get per egress port VLAN keep mode
- * Input:
- *      port        - Physical port number (0~7)
- *      pPortmask   - portmask(0~0xFF)
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_PORT_ID  - Invalid port number
- * Note:
- *      None
- */
-ret_t rtl8367c_getAsicVlanEgressKeep(rtk_uint32 port, rtk_uint32* pPortmask)
-{
-    rtk_uint32 regAddr, bit_mask, regval_l, regval_h;
-    ret_t  retVal;
-
-    if(port > RTL8367C_PORTIDMAX)
-        return RT_ERR_PORT_ID;
-
-    if(port < 8){
-        retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL0 + (port>>1),RTL8367C_PORT0_VLAN_KEEP_MASK_MASK<<((port&1)*8),&regval_l);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-        regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL0_EXT + (port>>1);
-        bit_mask = RTL8367C_PORT0_VLAN_KEEP_MASK_EXT_MASK;
-        bit_mask <<= (port&1)*3;
-        retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, &regval_h);
-        if(retVal != RT_ERR_OK)
-            return retVal;
-        *pPortmask = (regval_h << 8) | regval_l;
-    }
-    else{
-        switch(port){
-            case 8:
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4;
-                bit_mask = RTL8367C_PORT8_VLAN_KEEP_MASK_MASK;
-                retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, &regval_l);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4_EXT;
-                bit_mask = RTL8367C_PORT8_VLAN_KEEP_MASK_EXT_MASK;
-                retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, &regval_h);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-
-                *pPortmask = (regval_h << 8) | regval_l;
-                break;
-
-            case 9:
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4;
-                bit_mask = RTL8367C_PORT9_VLAN_KEEP_MASK_MASK;
-                retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, &regval_l);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL4_EXT;
-                bit_mask = RTL8367C_PORT9_VLAN_KEEP_MASK_EXT_MASK;
-                retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, &regval_h);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-
-                *pPortmask = (regval_h << 8) | regval_l;
-                break;
-
-            case 10:
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL5;
-                bit_mask = RTL8367C_VLAN_EGRESS_KEEP_CTRL5_MASK;
-                retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, &regval_l);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-                regAddr = RTL8367C_REG_VLAN_EGRESS_KEEP_CTRL5_EXT;
-                bit_mask = RTL8367C_VLAN_EGRESS_KEEP_CTRL5_EXT_MASK;
-                retVal = rtl8367c_getAsicRegBits(regAddr, bit_mask, &regval_h);
-                if(retVal != RT_ERR_OK)
-                    return retVal;
-
-                *pPortmask = (regval_h << 8) | regval_l;
-                break;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_setReservedVidAction
- * Description:
- *      Set reserved VID action
- * Input:
- *      vid0Action      - VID 0 action
- *      vid4095Action   - VID 4095 action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Error input
- * Note:
- *      None
- */
-ret_t rtl8367c_setReservedVidAction(rtk_uint32 vid0Action, rtk_uint32 vid4095Action)
-{
-    ret_t   retVal;
-
-    if(vid0Action >= RES_VID_ACT_END)
-        return RT_ERR_INPUT;
-
-    if(vid4095Action >= RES_VID_ACT_END)
-        return RT_ERR_INPUT;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_VLAN_EXT_CTRL, RTL8367C_VLAN_VID0_TYPE_OFFSET, vid0Action)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_VLAN_EXT_CTRL, RTL8367C_VLAN_VID4095_TYPE_OFFSET, vid4095Action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getReservedVidAction
- * Description:
- *      Get reserved VID action
- * Input:
- *      pVid0Action     - VID 0 action
- *      pVid4095Action  - VID 4095 action
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - Success
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - Null pointer
- * Note:
- *      None
- */
-ret_t rtl8367c_getReservedVidAction(rtk_uint32 *pVid0Action, rtk_uint32 *pVid4095Action)
-{
-    ret_t   retVal;
-
-    if(pVid0Action == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(pVid4095Action == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_VLAN_EXT_CTRL, RTL8367C_VLAN_VID0_TYPE_OFFSET, pVid0Action)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_VLAN_EXT_CTRL, RTL8367C_VLAN_VID4095_TYPE_OFFSET, pVid4095Action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtl8367c_setRealKeepRemarkEn
- * Description:
- *      Set Real Keep Remark
- * Input:
- *      enabled         - 0: 1P remarking is forbidden at real keep packet, 1: 1P remarking is enabled at real keep packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Error input
- * Note:
- *      None
- */
-ret_t rtl8367c_setRealKeepRemarkEn(rtk_uint32 enabled)
-{
-    ret_t   retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_VLAN_EXT_CTRL, RTL8367C_VLAN_1P_REMARK_BYPASS_REALKEEP_OFFSET, enabled)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_getRealKeepRemarkEn
- * Description:
- *      Get Real Keep Remark
- * Input:
- *      None
- * Output:
- *      pEnabled        - 0: 1P remarking is forbidden at real keep packet, 1: 1P remarking is enabled at real keep packet
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- *      RT_ERR_INPUT    - Error input
- * Note:
- *      None
- */
-ret_t rtl8367c_getRealKeepRemarkEn(rtk_uint32 *pEnabled)
-{
-    ret_t   retVal;
-
-    if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_VLAN_EXT_CTRL, RTL8367C_VLAN_1P_REMARK_BYPASS_REALKEEP_OFFSET, pEnabled)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtl8367c_resetVlan
- * Description:
- *      Reset VLAN table
- * Input:
- *      None.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK       - Success
- *      RT_ERR_SMI      - SMI access error
- * Note:
- *      None
- */
-ret_t rtl8367c_resetVlan(void)
-{
-    ret_t   retVal;
-
-    if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_VLAN_EXT_CTRL2, RTL8367C_VLAN_EXT_CTRL2_OFFSET, 1)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/smi.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/smi.c
deleted file mode 100644
index c272cad48e..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/smi.c
+++ /dev/null
@@ -1,444 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * Purpose : RTL8367C switch low-level function for access register
- * Feature : SMI related functions
- *
- */
-
-
-#include <rtk_types.h>
-#include <smi.h>
-#include "rtk_error.h"
-
-
-#if defined(MDC_MDIO_OPERATION)
-/*******************************************************************************/
-/*  MDC/MDIO porting                                                           */
-/*******************************************************************************/
-/* define the PHY ID currently used */
-/* carlos */
-#if 0
-#define MDC_MDIO_PHY_ID     0  /* PHY ID 0 or 29 */
-#else
-#define MDC_MDIO_PHY_ID     29  /* PHY ID 0 or 29 */
-#endif
-
-/* MDC/MDIO, redefine/implement the following Macro */ /*carlos*/
-#if 0
-#define MDC_MDIO_WRITE(preamableLength, phyID, regID, data)
-#define MDC_MDIO_READ(preamableLength, phyID, regID, pData)
-#else
-#define u32      unsigned int
-extern u32 mii_mgr_read(u32 phy_addr, u32 phy_register, u32 *read_data);
-extern u32 mii_mgr_write(u32 phy_addr, u32 phy_register, u32 write_data);
-
-#define MDC_MDIO_WRITE(preamableLength, phyID, regID, data) mii_mgr_write(phyID, regID, data)
-#define MDC_MDIO_READ(preamableLength, phyID, regID, pData) mii_mgr_read(phyID, regID, pData)
-#endif
-
-
-
-
-
-#elif defined(SPI_OPERATION)
-/*******************************************************************************/
-/*  SPI porting                                                                */
-/*******************************************************************************/
-/* SPI, redefine/implement the following Macro */
-#define SPI_WRITE(data, length)
-#define SPI_READ(pData, length)
-
-
-
-
-
-#else
-/*******************************************************************************/
-/*  I2C porting                                                                */
-/*******************************************************************************/
-/* Define the GPIO ID for SCK & SDA */
-rtk_uint32  smi_SCK = 1;    /* GPIO used for SMI Clock Generation */
-rtk_uint32  smi_SDA = 2;    /* GPIO used for SMI Data signal */
-
-/* I2C, redefine/implement the following Macro */
-#define GPIO_DIRECTION_SET(gpioID, direction)
-#define GPIO_DATA_SET(gpioID, data)
-#define GPIO_DATA_GET(gpioID, pData)
-
-
-
-
-
-#endif
-
-static void rtlglue_drvMutexLock(void)
-{
-    /* It is empty currently. Implement this function if Lock/Unlock function is needed */
-    return;
-}
-
-static void rtlglue_drvMutexUnlock(void)
-{
-    /* It is empty currently. Implement this function if Lock/Unlock function is needed */
-    return;
-}
-
-
-
-#if defined(MDC_MDIO_OPERATION) || defined(SPI_OPERATION)
-    /* No local function in MDC/MDIO & SPI mode */
-#else
-static void _smi_start(void)
-{
-
-    /* change GPIO pin to Output only */
-    GPIO_DIRECTION_SET(smi_SCK, GPIO_DIR_OUT);
-    GPIO_DIRECTION_SET(smi_SDA, GPIO_DIR_OUT);
-
-    /* Initial state: SCK: 0, SDA: 1 */
-    GPIO_DATA_SET(smi_SCK, 0);
-    GPIO_DATA_SET(smi_SDA, 1);
-    CLK_DURATION(DELAY);
-
-    /* CLK 1: 0 -> 1, 1 -> 0 */
-    GPIO_DATA_SET(smi_SCK, 1);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SCK, 0);
-    CLK_DURATION(DELAY);
-
-    /* CLK 2: */
-    GPIO_DATA_SET(smi_SCK, 1);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SDA, 0);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SCK, 0);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SDA, 1);
-
-}
-
-
-
-static void _smi_writeBit(rtk_uint16 signal, rtk_uint32 bitLen)
-{
-    for( ; bitLen > 0; bitLen--)
-    {
-        CLK_DURATION(DELAY);
-
-        /* prepare data */
-        if ( signal & (1<<(bitLen-1)) )
-        {
-            GPIO_DATA_SET(smi_SDA, 1);
-        }
-        else
-        {
-            GPIO_DATA_SET(smi_SDA, 0);
-        }
-        CLK_DURATION(DELAY);
-
-        /* clocking */
-        GPIO_DATA_SET(smi_SCK, 1);
-        CLK_DURATION(DELAY);
-        GPIO_DATA_SET(smi_SCK, 0);
-    }
-}
-
-
-
-static void _smi_readBit(rtk_uint32 bitLen, rtk_uint32 *rData)
-{
-    rtk_uint32 u = 0;
-
-    /* change GPIO pin to Input only */
-    GPIO_DIRECTION_SET(smi_SDA, GPIO_DIR_IN);
-
-    for (*rData = 0; bitLen > 0; bitLen--)
-    {
-        CLK_DURATION(DELAY);
-
-        /* clocking */
-        GPIO_DATA_SET(smi_SCK, 1);
-        CLK_DURATION(DELAY);
-        GPIO_DATA_GET(smi_SDA, &u);
-        GPIO_DATA_SET(smi_SCK, 0);
-
-        *rData |= (u << (bitLen - 1));
-    }
-
-    /* change GPIO pin to Output only */
-    GPIO_DIRECTION_SET(smi_SDA, GPIO_DIR_OUT);
-}
-
-
-
-static void _smi_stop(void)
-{
-
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SDA, 0);
-    GPIO_DATA_SET(smi_SCK, 1);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SDA, 1);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SCK, 1);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SCK, 0);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SCK, 1);
-
-    /* add a click */
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SCK, 0);
-    CLK_DURATION(DELAY);
-    GPIO_DATA_SET(smi_SCK, 1);
-
-
-    /* change GPIO pin to Input only */
-    GPIO_DIRECTION_SET(smi_SDA, GPIO_DIR_IN);
-    GPIO_DIRECTION_SET(smi_SCK, GPIO_DIR_IN);
-}
-
-#endif /* End of #if defined(MDC_MDIO_OPERATION) || defined(SPI_OPERATION) */
-
-rtk_int32 smi_read(rtk_uint32 mAddrs, rtk_uint32 *rData)
-{
-#if (!defined(MDC_MDIO_OPERATION) && !defined(SPI_OPERATION))
-    rtk_uint32 rawData=0, ACK;
-    rtk_uint8  con;
-    rtk_uint32 ret = RT_ERR_OK;
-#endif
-
-    if(mAddrs > 0xFFFF)
-        return RT_ERR_INPUT;
-
-    if(rData == NULL)
-        return RT_ERR_NULL_POINTER;
-
-#if defined(MDC_MDIO_OPERATION)
-
-    /* Lock */
-    rtlglue_drvMutexLock();
-
-    /* Write address control code to register 31 */
-    MDC_MDIO_WRITE(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_CTRL0_REG, MDC_MDIO_ADDR_OP);
-
-    /* Write address to register 23 */
-    MDC_MDIO_WRITE(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_ADDRESS_REG, mAddrs);
-
-    /* Write read control code to register 21 */
-    MDC_MDIO_WRITE(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_CTRL1_REG, MDC_MDIO_READ_OP);
-
-    /* Read data from register 25 */
-    MDC_MDIO_READ(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_DATA_READ_REG, rData);
-
-    /* Unlock */
-    rtlglue_drvMutexUnlock();
-
-    return RT_ERR_OK;
-
-#elif defined(SPI_OPERATION)
-
-    /* Lock */
-    rtlglue_drvMutexLock();
-
-    /* Write 8 bits READ OP_CODE */
-    SPI_WRITE(SPI_READ_OP, SPI_READ_OP_LEN);
-
-    /* Write 16 bits register address */
-    SPI_WRITE(mAddrs, SPI_REG_LEN);
-
-    /* Read 16 bits data */
-    SPI_READ(rData, SPI_DATA_LEN);
-
-    /* Unlock */
-    rtlglue_drvMutexUnlock();
-
-    return RT_ERR_OK;
-
-#else
-
-    /*Disable CPU interrupt to ensure that the SMI operation is atomic.
-      The API is based on RTL865X, rewrite the API if porting to other platform.*/
-    rtlglue_drvMutexLock();
-
-    _smi_start();                                /* Start SMI */
-
-    _smi_writeBit(0x0b, 4);                     /* CTRL code: 4'b1011 for RTL8370 */
-
-    _smi_writeBit(0x4, 3);                        /* CTRL code: 3'b100 */
-
-    _smi_writeBit(0x1, 1);                        /* 1: issue READ command */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                    /* ACK for issuing READ command*/
-    } while ((ACK != 0) && (con < ack_timer));
-
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_writeBit((mAddrs&0xff), 8);             /* Set reg_addr[7:0] */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                    /* ACK for setting reg_addr[7:0] */
-    } while ((ACK != 0) && (con < ack_timer));
-
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_writeBit((mAddrs>>8), 8);                 /* Set reg_addr[15:8] */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                    /* ACK by RTL8369 */
-    } while ((ACK != 0) && (con < ack_timer));
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_readBit(8, &rawData);                    /* Read DATA [7:0] */
-    *rData = rawData&0xff;
-
-    _smi_writeBit(0x00, 1);                        /* ACK by CPU */
-
-    _smi_readBit(8, &rawData);                    /* Read DATA [15: 8] */
-
-    _smi_writeBit(0x01, 1);                        /* ACK by CPU */
-    *rData |= (rawData<<8);
-
-    _smi_stop();
-
-    rtlglue_drvMutexUnlock();/*enable CPU interrupt*/
-
-    return ret;
-#endif /* end of #if defined(MDC_MDIO_OPERATION) */
-}
-
-
-
-rtk_int32 smi_write(rtk_uint32 mAddrs, rtk_uint32 rData)
-{
-#if (!defined(MDC_MDIO_OPERATION) && !defined(SPI_OPERATION))
-    rtk_int8 con;
-    rtk_uint32 ACK;
-    rtk_uint32 ret = RT_ERR_OK;
-#endif
-
-    if(mAddrs > 0xFFFF)
-        return RT_ERR_INPUT;
-
-    if(rData > 0xFFFF)
-        return RT_ERR_INPUT;
-
-#if defined(MDC_MDIO_OPERATION)
-
-    /* Lock */
-    rtlglue_drvMutexLock();
-
-    /* Write address control code to register 31 */
-    MDC_MDIO_WRITE(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_CTRL0_REG, MDC_MDIO_ADDR_OP);
-
-    /* Write address to register 23 */
-    MDC_MDIO_WRITE(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_ADDRESS_REG, mAddrs);
-
-    /* Write data to register 24 */
-    MDC_MDIO_WRITE(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_DATA_WRITE_REG, rData);
-
-    /* Write data control code to register 21 */
-    MDC_MDIO_WRITE(MDC_MDIO_PREAMBLE_LEN, MDC_MDIO_PHY_ID, MDC_MDIO_CTRL1_REG, MDC_MDIO_WRITE_OP);
-
-    /* Unlock */
-    rtlglue_drvMutexUnlock();
-
-    return RT_ERR_OK;
-
-#elif defined(SPI_OPERATION)
-
-    /* Lock */
-    rtlglue_drvMutexLock();
-
-    /* Write 8 bits WRITE OP_CODE */
-    SPI_WRITE(SPI_WRITE_OP, SPI_WRITE_OP_LEN);
-
-    /* Write 16 bits register address */
-    SPI_WRITE(mAddrs, SPI_REG_LEN);
-
-    /* Write 16 bits data */
-    SPI_WRITE(rData, SPI_DATA_LEN);
-
-    /* Unlock */
-    rtlglue_drvMutexUnlock();
-
-    return RT_ERR_OK;
-#else
-
-    /*Disable CPU interrupt to ensure that the SMI operation is atomic.
-      The API is based on RTL865X, rewrite the API if porting to other platform.*/
-    rtlglue_drvMutexLock();
-
-    _smi_start();                                /* Start SMI */
-
-    _smi_writeBit(0x0b, 4);                     /* CTRL code: 4'b1011 for RTL8370*/
-
-    _smi_writeBit(0x4, 3);                        /* CTRL code: 3'b100 */
-
-    _smi_writeBit(0x0, 1);                        /* 0: issue WRITE command */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                    /* ACK for issuing WRITE command*/
-    } while ((ACK != 0) && (con < ack_timer));
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_writeBit((mAddrs&0xff), 8);             /* Set reg_addr[7:0] */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                    /* ACK for setting reg_addr[7:0] */
-    } while ((ACK != 0) && (con < ack_timer));
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_writeBit((mAddrs>>8), 8);                 /* Set reg_addr[15:8] */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                    /* ACK for setting reg_addr[15:8] */
-    } while ((ACK != 0) && (con < ack_timer));
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_writeBit(rData&0xff, 8);                /* Write Data [7:0] out */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                    /* ACK for writting data [7:0] */
-    } while ((ACK != 0) && (con < ack_timer));
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_writeBit(rData>>8, 8);                    /* Write Data [15:8] out */
-
-    con = 0;
-    do {
-        con++;
-        _smi_readBit(1, &ACK);                        /* ACK for writting data [15:8] */
-    } while ((ACK != 0) && (con < ack_timer));
-    if (ACK != 0) ret = RT_ERR_FAILED;
-
-    _smi_stop();
-
-    rtlglue_drvMutexUnlock();/*enable CPU interrupt*/
-
-    return ret;
-#endif /* end of #if defined(MDC_MDIO_OPERATION) */
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/stat.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/stat.c
deleted file mode 100644
index 3a328b0ca4..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/stat.c
+++ /dev/null
@@ -1,626 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in MIB module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <stat.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_mib.h>
-
-/* Function Name:
- *      rtk_stat_global_reset
- * Description:
- *      Reset global MIB counter.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Reset MIB counter of ports. API will use global reset while port mask is all-ports.
- */
-rtk_api_ret_t rtk_stat_global_reset(void)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_setAsicMIBsCounterReset(TRUE,FALSE, 0)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_port_reset
- * Description:
- *      Reset per port MIB counter by port.
- * Input:
- *      port - port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-rtk_api_ret_t rtk_stat_port_reset(rtk_port_t port)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_setAsicMIBsCounterReset(FALSE,FALSE,1 << rtk_switch_port_L2P_get(port))) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_queueManage_reset
- * Description:
- *      Reset queue manage MIB counter.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-rtk_api_ret_t rtk_stat_queueManage_reset(void)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_setAsicMIBsCounterReset(FALSE,TRUE,0)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_stat_global_get
- * Description:
- *      Get global MIB counter
- * Input:
- *      cntr_idx - global counter index.
- * Output:
- *      pCntr - global counter value.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get global MIB counter by index definition.
- */
-rtk_api_ret_t rtk_stat_global_get(rtk_stat_global_type_t cntr_idx, rtk_stat_counter_t *pCntr)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pCntr)
-        return RT_ERR_NULL_POINTER;
-
-    if (cntr_idx!=DOT1D_TP_LEARNED_ENTRY_DISCARDS_INDEX)
-        return RT_ERR_STAT_INVALID_GLOBAL_CNTR;
-
-    if ((retVal = rtl8367c_getAsicMIBsCounter(0, cntr_idx, pCntr)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_global_getAll
- * Description:
- *      Get all global MIB counter
- * Input:
- *      None
- * Output:
- *      pGlobal_cntrs - global counter structure.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get all global MIB counter by index definition.
- */
-rtk_api_ret_t rtk_stat_global_getAll(rtk_stat_global_cntr_t *pGlobal_cntrs)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pGlobal_cntrs)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicMIBsCounter(0,DOT1D_TP_LEARNED_ENTRY_DISCARDS_INDEX, &pGlobal_cntrs->dot1dTpLearnedEntryDiscards)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-#define MIB_NOT_SUPPORT     (0xFFFF)
-static rtk_api_ret_t _get_asic_mib_idx(rtk_stat_port_type_t cnt_idx, RTL8367C_MIBCOUNTER *pMib_idx)
-{
-    RTL8367C_MIBCOUNTER mib_asic_idx[STAT_PORT_CNTR_END]=
-    {
-        ifInOctets,                     /* STAT_IfInOctets */
-        dot3StatsFCSErrors,             /* STAT_Dot3StatsFCSErrors */
-        dot3StatsSymbolErrors,          /* STAT_Dot3StatsSymbolErrors */
-        dot3InPauseFrames,              /* STAT_Dot3InPauseFrames */
-        dot3ControlInUnknownOpcodes,    /* STAT_Dot3ControlInUnknownOpcodes */
-        etherStatsFragments,            /* STAT_EtherStatsFragments */
-        etherStatsJabbers,              /* STAT_EtherStatsJabbers */
-        ifInUcastPkts,                  /* STAT_IfInUcastPkts */
-        etherStatsDropEvents,           /* STAT_EtherStatsDropEvents */
-        etherStatsOctets,               /* STAT_EtherStatsOctets */
-        etherStatsUnderSizePkts,        /* STAT_EtherStatsUnderSizePkts */
-        etherOversizeStats,             /* STAT_EtherOversizeStats */
-        etherStatsPkts64Octets,         /* STAT_EtherStatsPkts64Octets */
-        etherStatsPkts65to127Octets,    /* STAT_EtherStatsPkts65to127Octets */
-        etherStatsPkts128to255Octets,   /* STAT_EtherStatsPkts128to255Octets */
-        etherStatsPkts256to511Octets,   /* STAT_EtherStatsPkts256to511Octets */
-        etherStatsPkts512to1023Octets,  /* STAT_EtherStatsPkts512to1023Octets */
-        etherStatsPkts1024to1518Octets, /* STAT_EtherStatsPkts1024to1518Octets */
-        ifInMulticastPkts,              /* STAT_EtherStatsMulticastPkts */
-        ifInBroadcastPkts,              /* STAT_EtherStatsBroadcastPkts */
-        ifOutOctets,                    /* STAT_IfOutOctets */
-        dot3StatsSingleCollisionFrames, /* STAT_Dot3StatsSingleCollisionFrames */
-        dot3StatMultipleCollisionFrames,/* STAT_Dot3StatsMultipleCollisionFrames */
-        dot3sDeferredTransmissions,     /* STAT_Dot3StatsDeferredTransmissions */
-        dot3StatsLateCollisions,        /* STAT_Dot3StatsLateCollisions */
-        etherStatsCollisions,           /* STAT_EtherStatsCollisions */
-        dot3StatsExcessiveCollisions,   /* STAT_Dot3StatsExcessiveCollisions */
-        dot3OutPauseFrames,             /* STAT_Dot3OutPauseFrames */
-        MIB_NOT_SUPPORT,                /* STAT_Dot1dBasePortDelayExceededDiscards */
-        dot1dTpPortInDiscards,          /* STAT_Dot1dTpPortInDiscards */
-        ifOutUcastPkts,                 /* STAT_IfOutUcastPkts */
-        ifOutMulticastPkts,             /* STAT_IfOutMulticastPkts */
-        ifOutBroadcastPkts,             /* STAT_IfOutBroadcastPkts */
-        outOampduPkts,                  /* STAT_OutOampduPkts */
-        inOampduPkts,                   /* STAT_InOampduPkts */
-        MIB_NOT_SUPPORT,                /* STAT_PktgenPkts */
-        inMldChecksumError,             /* STAT_InMldChecksumError */
-        inIgmpChecksumError,            /* STAT_InIgmpChecksumError */
-        inMldSpecificQuery,             /* STAT_InMldSpecificQuery */
-        inMldGeneralQuery,              /* STAT_InMldGeneralQuery */
-        inIgmpSpecificQuery,            /* STAT_InIgmpSpecificQuery */
-        inIgmpGeneralQuery,             /* STAT_InIgmpGeneralQuery */
-        inMldLeaves,                    /* STAT_InMldLeaves */
-        inIgmpLeaves,                   /* STAT_InIgmpInterfaceLeaves */
-        inIgmpJoinsSuccess,             /* STAT_InIgmpJoinsSuccess */
-        inIgmpJoinsFail,                /* STAT_InIgmpJoinsFail */
-        inMldJoinsSuccess,              /* STAT_InMldJoinsSuccess */
-        inMldJoinsFail,                 /* STAT_InMldJoinsFail */
-        inReportSuppressionDrop,        /* STAT_InReportSuppressionDrop */
-        inLeaveSuppressionDrop,         /* STAT_InLeaveSuppressionDrop */
-        outIgmpReports,                 /* STAT_OutIgmpReports */
-        outIgmpLeaves,                  /* STAT_OutIgmpLeaves */
-        outIgmpGeneralQuery,            /* STAT_OutIgmpGeneralQuery */
-        outIgmpSpecificQuery,           /* STAT_OutIgmpSpecificQuery */
-        outMldReports,                  /* STAT_OutMldReports */
-        outMldLeaves,                   /* STAT_OutMldLeaves */
-        outMldGeneralQuery,             /* STAT_OutMldGeneralQuery */
-        outMldSpecificQuery,            /* STAT_OutMldSpecificQuery */
-        inKnownMulticastPkts,           /* STAT_InKnownMulticastPkts */
-        ifInMulticastPkts,              /* STAT_IfInMulticastPkts */
-        ifInBroadcastPkts,              /* STAT_IfInBroadcastPkts */
-        ifOutDiscards                   /* STAT_IfOutDiscards */
-    };
-
-    if(cnt_idx >= STAT_PORT_CNTR_END)
-        return RT_ERR_STAT_INVALID_PORT_CNTR;
-
-    if(mib_asic_idx[cnt_idx] == MIB_NOT_SUPPORT)
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    *pMib_idx = mib_asic_idx[cnt_idx];
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_port_get
- * Description:
- *      Get per port MIB counter by index
- * Input:
- *      port        - port id.
- *      cntr_idx    - port counter index.
- * Output:
- *      pCntr - MIB retrived counter.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Get per port MIB counter by index definition.
- */
-rtk_api_ret_t rtk_stat_port_get(rtk_port_t port, rtk_stat_port_type_t cntr_idx, rtk_stat_counter_t *pCntr)
-{
-    rtk_api_ret_t       retVal;
-    RTL8367C_MIBCOUNTER mib_idx;
-    rtk_stat_counter_t  second_cnt;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pCntr)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (cntr_idx>=STAT_PORT_CNTR_END)
-        return RT_ERR_STAT_INVALID_PORT_CNTR;
-
-    if((retVal = _get_asic_mib_idx(cntr_idx, &mib_idx)) != RT_ERR_OK)
-        return retVal;
-
-    if(mib_idx == MIB_NOT_SUPPORT)
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    if ((retVal = rtl8367c_getAsicMIBsCounter(rtk_switch_port_L2P_get(port), mib_idx, pCntr)) != RT_ERR_OK)
-        return retVal;
-
-    if(cntr_idx == STAT_EtherStatsMulticastPkts)
-    {
-        if((retVal = _get_asic_mib_idx(STAT_IfOutMulticastPkts, &mib_idx)) != RT_ERR_OK)
-            return retVal;
-
-        if((retVal = rtl8367c_getAsicMIBsCounter(rtk_switch_port_L2P_get(port), mib_idx, &second_cnt)) != RT_ERR_OK)
-            return retVal;
-
-        *pCntr += second_cnt;
-    }
-
-    if(cntr_idx == STAT_EtherStatsBroadcastPkts)
-    {
-        if((retVal = _get_asic_mib_idx(STAT_IfOutBroadcastPkts, &mib_idx)) != RT_ERR_OK)
-            return retVal;
-
-        if((retVal = rtl8367c_getAsicMIBsCounter(rtk_switch_port_L2P_get(port), mib_idx, &second_cnt)) != RT_ERR_OK)
-            return retVal;
-
-        *pCntr += second_cnt;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_port_getAll
- * Description:
- *      Get all counters of one specified port in the specified device.
- * Input:
- *      port - port id.
- * Output:
- *      pPort_cntrs - buffer pointer of counter value.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get all MIB counters of one port.
- */
-rtk_api_ret_t rtk_stat_port_getAll(rtk_port_t port, rtk_stat_port_cntr_t *pPort_cntrs)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 mibIndex;
-    rtk_uint64 mibCounter;
-    rtk_uint32 *accessPtr;
-    /* address offset to MIBs counter */
-    CONST_T rtk_uint16 mibLength[STAT_PORT_CNTR_END]= {
-        2,1,1,1,1,1,1,1,1,
-        2,1,1,1,1,1,1,1,1,1,1,
-        2,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,
-        1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1};
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPort_cntrs)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    accessPtr = (rtk_uint32*)pPort_cntrs;
-    for (mibIndex=0;mibIndex<STAT_PORT_CNTR_END;mibIndex++)
-    {
-        if ((retVal = rtk_stat_port_get(port, mibIndex, &mibCounter)) != RT_ERR_OK)
-        {
-            if (retVal == RT_ERR_CHIP_NOT_SUPPORTED)
-                mibCounter = 0;
-            else
-                return retVal;
-        }
-
-        if (2 == mibLength[mibIndex])
-            *(rtk_uint64*)accessPtr = mibCounter;
-        else if (1 == mibLength[mibIndex])
-            *accessPtr = mibCounter;
-        else
-            return RT_ERR_FAILED;
-
-        accessPtr+=mibLength[mibIndex];
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_logging_counterCfg_set
- * Description:
- *      Set the type and mode of Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. Should be even number only.(0,2,4,6,8.....30)
- *      mode    - 32 bits or 64 bits mode
- *      type    - Packet counter or byte counter
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Set the type and mode of Logging Counter.
- */
-rtk_api_ret_t rtk_stat_logging_counterCfg_set(rtk_uint32 idx, rtk_logging_counter_mode_t mode, rtk_logging_counter_type_t type)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(idx > RTL8367C_MIB_MAX_LOG_CNT_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((idx % 2) == 1)
-        return RT_ERR_INPUT;
-
-    if(mode >= LOGGING_MODE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(type >= LOGGING_TYPE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((retVal = rtl8367c_setAsicMIBsLoggingType((idx / 2), (rtk_uint32)type)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicMIBsLoggingMode((idx / 2), (rtk_uint32)mode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_logging_counterCfg_get
- * Description:
- *      Get the type and mode of Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. Should be even number only.(0,2,4,6,8.....30)
- * Output:
- *      pMode   - 32 bits or 64 bits mode
- *      pType   - Packet counter or byte counter
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_NULL_POINTER - NULL Pointer
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      Get the type and mode of Logging Counter.
- */
-rtk_api_ret_t rtk_stat_logging_counterCfg_get(rtk_uint32 idx, rtk_logging_counter_mode_t *pMode, rtk_logging_counter_type_t *pType)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      type, mode;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(idx > RTL8367C_MIB_MAX_LOG_CNT_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((idx % 2) == 1)
-        return RT_ERR_INPUT;
-
-    if(pMode == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(pType == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if((retVal = rtl8367c_getAsicMIBsLoggingType((idx / 2), &type)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicMIBsLoggingMode((idx / 2), &mode)) != RT_ERR_OK)
-        return retVal;
-
-    *pMode = (rtk_logging_counter_mode_t)mode;
-    *pType = (rtk_logging_counter_type_t)type;
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_stat_logging_counter_reset
- * Description:
- *      Reset Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. (0~31)
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Reset Logging Counter.
- */
-rtk_api_ret_t rtk_stat_logging_counter_reset(rtk_uint32 idx)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(idx > RTL8367C_MIB_MAX_LOG_CNT_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((retVal = rtl8367c_setAsicMIBsResetLoggingCounter(idx)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_logging_counter_get
- * Description:
- *      Get Logging Counter
- * Input:
- *      idx     - The index of Logging Counter. (0~31)
- * Output:
- *      pCnt    - Logging counter value
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_OUT_OF_RANGE - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Get Logging Counter.
- */
-rtk_api_ret_t rtk_stat_logging_counter_get(rtk_uint32 idx, rtk_uint32 *pCnt)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pCnt)
-        return RT_ERR_NULL_POINTER;
-
-    if(idx > RTL8367C_MIB_MAX_LOG_CNT_IDX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if((retVal = rtl8367c_getAsicMIBsLogCounter(idx, pCnt)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_lengthMode_set
- * Description:
- *      Set Legnth mode.
- * Input:
- *      txMode     - The length counting mode
- *      rxMode     - The length counting mode
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_INPUT        - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *
- */
-rtk_api_ret_t rtk_stat_lengthMode_set(rtk_stat_lengthMode_t txMode, rtk_stat_lengthMode_t rxMode)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(txMode >= LENGTH_MODE_END)
-        return RT_ERR_INPUT;
-
-    if(rxMode >= LENGTH_MODE_END)
-        return RT_ERR_INPUT;
-
-    if((retVal = rtl8367c_setAsicMIBsLength((rtk_uint32)txMode, (rtk_uint32)rxMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stat_lengthMode_get
- * Description:
- *      Get Legnth mode.
- * Input:
- *      None.
- * Output:
- *      pTxMode       - The length counting mode
- *      pRxMode       - The length counting mode
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_INPUT        - Out of range.
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- */
-rtk_api_ret_t rtk_stat_lengthMode_get(rtk_stat_lengthMode_t *pTxMode, rtk_stat_lengthMode_t *pRxMode)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pTxMode)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pRxMode)
-        return RT_ERR_NULL_POINTER;
-
-    if((retVal = rtl8367c_getAsicMIBsLength((rtk_uint32 *)pTxMode, (rtk_uint32 *)pRxMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/storm.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/storm.c
deleted file mode 100644
index 13cf4e3cb4..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/storm.c
+++ /dev/null
@@ -1,816 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in Storm module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <storm.h>
-#include <rate.h>
-#include <string.h>
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_storm.h>
-#include <rtl8367c_asicdrv_meter.h>
-#include <rtl8367c_asicdrv_rma.h>
-#include <rtl8367c_asicdrv_igmp.h>
-
-/* Function Name:
- *      rtk_rate_stormControlMeterIdx_set
- * Description:
- *      Set the storm control meter index.
- * Input:
- *      port       - port id
- *      storm_type - storm group type
- *      index       - storm control meter index.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID - Invalid port id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlMeterIdx_set(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_uint32 index)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if (index > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterUnknownUnicastMeter(rtk_switch_port_L2P_get(port), index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterUnknownMulticastMeter(rtk_switch_port_L2P_get(port), index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterMulticastMeter(rtk_switch_port_L2P_get(port), index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_setAsicStormFilterBroadcastMeter(rtk_switch_port_L2P_get(port), index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlMeterIdx_get
- * Description:
- *      Get the storm control meter index.
- * Input:
- *      port       - port id
- *      storm_type - storm group type
- * Output:
- *      pIndex     - storm control meter index.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_PORT_ID - Invalid port id
- *      RT_ERR_FILTER_METER_ID  - Invalid meter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlMeterIdx_get(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_uint32 *pIndex)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if (NULL == pIndex )
-        return RT_ERR_NULL_POINTER;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterUnknownUnicastMeter(rtk_switch_port_L2P_get(port), pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterUnknownMulticastMeter(rtk_switch_port_L2P_get(port), pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterMulticastMeter(rtk_switch_port_L2P_get(port), pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_getAsicStormFilterBroadcastMeter(rtk_switch_port_L2P_get(port), pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlPortEnable_set
- * Description:
- *      Set enable status of storm control on specified port.
- * Input:
- *      port       - port id
- *      stormType  - storm group type
- *      enable     - enable status of storm control
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_PORT_ID           - invalid port id
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlPortEnable_set(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterUnknownUnicastEnable(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterUnknownMulticastEnable(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterMulticastEnable(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_setAsicStormFilterBroadcastEnable(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlPortEnable_set
- * Description:
- *      Set enable status of storm control on specified port.
- * Input:
- *      port       - port id
- *      stormType  - storm group type
- * Output:
- *      pEnable     - enable status of storm control
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_PORT_ID           - invalid port id
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlPortEnable_get(rtk_port_t port, rtk_rate_storm_group_t stormType, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if (NULL == pEnable)
-        return RT_ERR_ENABLE;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterUnknownUnicastEnable(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterUnknownMulticastEnable(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterMulticastEnable(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_getAsicStormFilterBroadcastEnable(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_storm_bypass_set
- * Description:
- *      Set bypass storm filter control configuration.
- * Input:
- *      type    - Bypass storm filter control type.
- *      enable  - Bypass status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid IFG parameter
- * Note:
- *
- *      This API can set per-port bypass stomr filter control frame type including RMA and igmp.
- *      The bypass frame type is as following:
- *      - BYPASS_BRG_GROUP,
- *      - BYPASS_FD_PAUSE,
- *      - BYPASS_SP_MCAST,
- *      - BYPASS_1X_PAE,
- *      - BYPASS_UNDEF_BRG_04,
- *      - BYPASS_UNDEF_BRG_05,
- *      - BYPASS_UNDEF_BRG_06,
- *      - BYPASS_UNDEF_BRG_07,
- *      - BYPASS_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - BYPASS_UNDEF_BRG_09,
- *      - BYPASS_UNDEF_BRG_0A,
- *      - BYPASS_UNDEF_BRG_0B,
- *      - BYPASS_UNDEF_BRG_0C,
- *      - BYPASS_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - BYPASS_8021AB,
- *      - BYPASS_UNDEF_BRG_0F,
- *      - BYPASS_BRG_MNGEMENT,
- *      - BYPASS_UNDEFINED_11,
- *      - BYPASS_UNDEFINED_12,
- *      - BYPASS_UNDEFINED_13,
- *      - BYPASS_UNDEFINED_14,
- *      - BYPASS_UNDEFINED_15,
- *      - BYPASS_UNDEFINED_16,
- *      - BYPASS_UNDEFINED_17,
- *      - BYPASS_UNDEFINED_18,
- *      - BYPASS_UNDEFINED_19,
- *      - BYPASS_UNDEFINED_1A,
- *      - BYPASS_UNDEFINED_1B,
- *      - BYPASS_UNDEFINED_1C,
- *      - BYPASS_UNDEFINED_1D,
- *      - BYPASS_UNDEFINED_1E,
- *      - BYPASS_UNDEFINED_1F,
- *      - BYPASS_GMRP,
- *      - BYPASS_GVRP,
- *      - BYPASS_UNDEF_GARP_22,
- *      - BYPASS_UNDEF_GARP_23,
- *      - BYPASS_UNDEF_GARP_24,
- *      - BYPASS_UNDEF_GARP_25,
- *      - BYPASS_UNDEF_GARP_26,
- *      - BYPASS_UNDEF_GARP_27,
- *      - BYPASS_UNDEF_GARP_28,
- *      - BYPASS_UNDEF_GARP_29,
- *      - BYPASS_UNDEF_GARP_2A,
- *      - BYPASS_UNDEF_GARP_2B,
- *      - BYPASS_UNDEF_GARP_2C,
- *      - BYPASS_UNDEF_GARP_2D,
- *      - BYPASS_UNDEF_GARP_2E,
- *      - BYPASS_UNDEF_GARP_2F,
- *      - BYPASS_IGMP.
- *      - BYPASS_CDP.
- *      - BYPASS_CSSTP.
- *      - BYPASS_LLDP.
- */
-rtk_api_ret_t rtk_storm_bypass_set(rtk_storm_bypass_t type, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= BYPASS_END)
-        return RT_ERR_INPUT;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (type >= 0 && type <= BYPASS_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.discard_storm_filter = enable;
-
-        if ((retVal = rtl8367c_setAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if(type == BYPASS_IGMP)
-    {
-        if ((retVal = rtl8367c_setAsicIGMPBypassStormCTRL(enable)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type == BYPASS_CDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.discard_storm_filter = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type  == BYPASS_CSSTP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.discard_storm_filter = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type  == BYPASS_LLDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.discard_storm_filter = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaLldp(tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_storm_bypass_get
- * Description:
- *      Get bypass storm filter control configuration.
- * Input:
- *      type - Bypass storm filter control type.
- * Output:
- *      pEnable - Bypass status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API can get per-port bypass stomr filter control frame type including RMA and igmp.
- *      The bypass frame type is as following:
- *      - BYPASS_BRG_GROUP,
- *      - BYPASS_FD_PAUSE,
- *      - BYPASS_SP_MCAST,
- *      - BYPASS_1X_PAE,
- *      - BYPASS_UNDEF_BRG_04,
- *      - BYPASS_UNDEF_BRG_05,
- *      - BYPASS_UNDEF_BRG_06,
- *      - BYPASS_UNDEF_BRG_07,
- *      - BYPASS_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - BYPASS_UNDEF_BRG_09,
- *      - BYPASS_UNDEF_BRG_0A,
- *      - BYPASS_UNDEF_BRG_0B,
- *      - BYPASS_UNDEF_BRG_0C,
- *      - BYPASS_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - BYPASS_8021AB,
- *      - BYPASS_UNDEF_BRG_0F,
- *      - BYPASS_BRG_MNGEMENT,
- *      - BYPASS_UNDEFINED_11,
- *      - BYPASS_UNDEFINED_12,
- *      - BYPASS_UNDEFINED_13,
- *      - BYPASS_UNDEFINED_14,
- *      - BYPASS_UNDEFINED_15,
- *      - BYPASS_UNDEFINED_16,
- *      - BYPASS_UNDEFINED_17,
- *      - BYPASS_UNDEFINED_18,
- *      - BYPASS_UNDEFINED_19,
- *      - BYPASS_UNDEFINED_1A,
- *      - BYPASS_UNDEFINED_1B,
- *      - BYPASS_UNDEFINED_1C,
- *      - BYPASS_UNDEFINED_1D,
- *      - BYPASS_UNDEFINED_1E,
- *      - BYPASS_UNDEFINED_1F,
- *      - BYPASS_GMRP,
- *      - BYPASS_GVRP,
- *      - BYPASS_UNDEF_GARP_22,
- *      - BYPASS_UNDEF_GARP_23,
- *      - BYPASS_UNDEF_GARP_24,
- *      - BYPASS_UNDEF_GARP_25,
- *      - BYPASS_UNDEF_GARP_26,
- *      - BYPASS_UNDEF_GARP_27,
- *      - BYPASS_UNDEF_GARP_28,
- *      - BYPASS_UNDEF_GARP_29,
- *      - BYPASS_UNDEF_GARP_2A,
- *      - BYPASS_UNDEF_GARP_2B,
- *      - BYPASS_UNDEF_GARP_2C,
- *      - BYPASS_UNDEF_GARP_2D,
- *      - BYPASS_UNDEF_GARP_2E,
- *      - BYPASS_UNDEF_GARP_2F,
- *      - BYPASS_IGMP.
- *      - BYPASS_CDP.
- *      - BYPASS_CSSTP.
- *      - BYPASS_LLDP.
- */
-rtk_api_ret_t rtk_storm_bypass_get(rtk_storm_bypass_t type, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= BYPASS_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if (type >= 0 && type <= BYPASS_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.discard_storm_filter;
-    }
-    else if(type == BYPASS_IGMP)
-    {
-        if ((retVal = rtl8367c_getAsicIGMPBypassStormCTRL(pEnable)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type == BYPASS_CDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.discard_storm_filter;
-    }
-    else if (type == BYPASS_CSSTP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.discard_storm_filter;
-    }
-    else if (type == BYPASS_LLDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp,&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.discard_storm_filter;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlExtPortmask_set
- * Description:
- *      Set externsion storm control port mask
- * Input:
- *      pPortmask  - port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlExtPortmask_set(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtk_switch_portmask_L2P_get(pPortmask, &pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicStormFilterExtEnablePortMask(pmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlExtPortmask_get
- * Description:
- *      Set externsion storm control port mask
- * Input:
- *      None
- * Output:
- *      pPortmask  - port mask
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlExtPortmask_get(rtk_portmask_t *pPortmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPortmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicStormFilterExtEnablePortMask(&pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmask, pPortmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlExtEnable_set
- * Description:
- *      Set externsion storm control state
- * Input:
- *      stormType   - storm group type
- *      enable      - externsion storm control state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlExtEnable_set(rtk_rate_storm_group_t stormType, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtUnknownUnicastEnable(enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtUnknownMulticastEnable(enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtMulticastEnable(enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtBroadcastEnable(enable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlExtEnable_get
- * Description:
- *      Get externsion storm control state
- * Input:
- *      stormType   - storm group type
- * Output:
- *      pEnable     - externsion storm control state
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlExtEnable_get(rtk_rate_storm_group_t stormType, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if (NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtUnknownUnicastEnable((rtk_uint32 *)pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtUnknownMulticastEnable((rtk_uint32 *)pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtMulticastEnable((rtk_uint32 *)pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtBroadcastEnable((rtk_uint32 *)pEnable)) != RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlExtMeterIdx_set
- * Description:
- *      Set externsion storm control meter index
- * Input:
- *      stormType   - storm group type
- *      index       - externsion storm control state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlExtMeterIdx_set(rtk_rate_storm_group_t stormType, rtk_uint32 index)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if (index > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtUnknownUnicastMeter(index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtUnknownMulticastMeter(index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtMulticastMeter(index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_setAsicStormFilterExtBroadcastMeter(index))!=RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_rate_stormControlExtMeterIdx_get
- * Description:
- *      Get externsion storm control meter index
- * Input:
- *      stormType   - storm group type
- *      pIndex      - externsion storm control state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT          - The module is not initial
- *      RT_ERR_INPUT             - invalid input parameter
- * Note:
- *
- */
-rtk_api_ret_t rtk_rate_stormControlExtMeterIdx_get(rtk_rate_storm_group_t stormType, rtk_uint32 *pIndex)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (stormType >= STORM_GROUP_END)
-        return RT_ERR_SFC_UNKNOWN_GROUP;
-
-    if(NULL == pIndex)
-        return RT_ERR_NULL_POINTER;
-
-    switch (stormType)
-    {
-        case STORM_GROUP_UNKNOWN_UNICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtUnknownUnicastMeter(pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_UNKNOWN_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtUnknownMulticastMeter(pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_MULTICAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtMulticastMeter(pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        case STORM_GROUP_BROADCAST:
-            if ((retVal = rtl8367c_getAsicStormFilterExtBroadcastMeter(pIndex))!=RT_ERR_OK)
-                return retVal;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/svlan.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/svlan.c
deleted file mode 100644
index bf4ef044d1..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/svlan.c
+++ /dev/null
@@ -1,2415 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in SVLAN module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <svlan.h>
-#include <vlan.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_svlan.h>
-
-rtk_uint8               svlan_mbrCfgUsage[RTL8367C_SVIDXNO];
-rtk_uint16              svlan_mbrCfgVid[RTL8367C_SVIDXNO];
-rtk_svlan_lookupType_t  svlan_lookupType;
-/* Function Name:
- *      rtk_svlan_init
- * Description:
- *      Initialize SVLAN Configuration
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      Ether type of S-tag in 802.1ad is 0x88a8 and there are existed ether type 0x9100 and 0x9200 for Q-in-Q SLAN design.
- *      User can set mathced ether type as service provider supported protocol.
- */
-rtk_api_ret_t rtk_svlan_init(void)
-{
-    rtk_uint32 i;
-    rtk_api_ret_t retVal;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_s2c_t svlanSP2CConf;
-    rtl8367c_svlan_mc2s_t svlanMC2SConf;
-    rtk_uint32 svidx;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /*default use C-priority*/
-    if ((retVal = rtl8367c_setAsicSvlanPrioritySel(SPRISEL_CTAGPRI)) != RT_ERR_OK)
-        return retVal;
-
-    /*Drop SVLAN untag frame*/
-    if ((retVal = rtl8367c_setAsicSvlanIngressUntag(UNTAG_DROP)) != RT_ERR_OK)
-        return retVal;
-
-    /*Drop SVLAN unmatch frame*/
-    if ((retVal = rtl8367c_setAsicSvlanIngressUnmatch(UNMATCH_DROP)) != RT_ERR_OK)
-        return retVal;
-
-    /*Set TPID to 0x88a8*/
-    if ((retVal = rtl8367c_setAsicSvlanTpid(0x88a8)) != RT_ERR_OK)
-        return retVal;
-
-    /*Clean Uplink Port Mask to none*/
-    if ((retVal = rtl8367c_setAsicSvlanUplinkPortMask(0)) != RT_ERR_OK)
-        return retVal;
-
-    /*Clean SVLAN Member Configuration*/
-    for (i=0; i<= RTL8367C_SVIDXMAX; i++)
-    {
-        memset(&svlanMemConf, 0, sizeof(rtl8367c_svlan_memconf_t));
-        if ((retVal = rtl8367c_setAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Clean C2S Configuration*/
-    for (i=0; i<= RTL8367C_C2SIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_setAsicSvlanC2SConf(i, 0,0,0)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Clean SP2C Configuration*/
-    for (i=0; i <= RTL8367C_SP2CMAX ; i++)
-    {
-        memset(&svlanSP2CConf, 0, sizeof(rtl8367c_svlan_s2c_t));
-        if ((retVal = rtl8367c_setAsicSvlanSP2CConf(i, &svlanSP2CConf)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /*Clean MC2S Configuration*/
-    for (i=0 ; i<= RTL8367C_MC2SIDXMAX; i++)
-    {
-        memset(&svlanMC2SConf, 0, sizeof(rtl8367c_svlan_mc2s_t));
-        if ((retVal = rtl8367c_setAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-    }
-
-
-    if ((retVal = rtk_svlan_lookupType_set(SVLAN_LOOKUP_S64MBRCGF)) != RT_ERR_OK)
-        return retVal;
-
-
-    for (svidx = 0; svidx <= RTL8367C_SVIDXMAX; svidx++)
-    {
-        svlan_mbrCfgUsage[svidx] = FALSE;
-    }
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_servicePort_add
- * Description:
- *      Add one service port in the specified device
- * Input:
- *      port - Port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      This API is setting which port is connected to provider switch. All frames receiving from this port must
- *      contain accept SVID in S-tag field.
- */
-rtk_api_ret_t rtk_svlan_servicePort_add(rtk_port_t port)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicSvlanUplinkPortMask(&pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    pmsk = pmsk | (1<<rtk_switch_port_L2P_get(port));
-
-    if ((retVal = rtl8367c_setAsicSvlanUplinkPortMask(pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_servicePort_get
- * Description:
- *      Get service ports in the specified device.
- * Input:
- *      None
- * Output:
- *      pSvlan_portmask - pointer buffer of svlan ports.
- * Return:
- *      RT_ERR_OK          - OK
- *      RT_ERR_FAILED      - Failed
- *      RT_ERR_SMI         - SMI access error
- * Note:
- *      This API is setting which port is connected to provider switch. All frames receiving from this port must
- *      contain accept SVID in S-tag field.
- */
-rtk_api_ret_t rtk_svlan_servicePort_get(rtk_portmask_t *pSvlan_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 phyMbrPmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvlan_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSvlanUplinkPortMask(&phyMbrPmask)) != RT_ERR_OK)
-        return retVal;
-
-    if(rtk_switch_portmask_P2L_get(phyMbrPmask, pSvlan_portmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_servicePort_del
- * Description:
- *      Delete one service port in the specified device
- * Input:
- *      port - Port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      This API is removing SVLAN service port in the specified device.
- */
-rtk_api_ret_t rtk_svlan_servicePort_del(rtk_port_t port)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicSvlanUplinkPortMask(&pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    pmsk = pmsk & ~(1<<rtk_switch_port_L2P_get(port));
-
-    if ((retVal = rtl8367c_setAsicSvlanUplinkPortMask(pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_tpidEntry_set
- * Description:
- *      Configure accepted S-VLAN ether type.
- * Input:
- *      svlan_tag_id - Ether type of S-tag frame parsing in uplink ports.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      Ether type of S-tag in 802.1ad is 0x88a8 and there are existed ether type 0x9100 and 0x9200 for Q-in-Q SLAN design.
- *      User can set mathced ether type as service provider supported protocol.
- */
-rtk_api_ret_t rtk_svlan_tpidEntry_set(rtk_svlan_tpid_t svlan_tag_id)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (svlan_tag_id>RTK_MAX_NUM_OF_PROTO_TYPE)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicSvlanTpid(svlan_tag_id)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_tpidEntry_get
- * Description:
- *      Get accepted S-VLAN ether type setting.
- * Input:
- *      None
- * Output:
- *      pSvlan_tag_id -  Ether type of S-tag frame parsing in uplink ports.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      This API is setting which port is connected to provider switch. All frames receiving from this port must
- *      contain accept SVID in S-tag field.
- */
-rtk_api_ret_t rtk_svlan_tpidEntry_get(rtk_svlan_tpid_t *pSvlan_tag_id)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvlan_tag_id)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSvlanTpid(pSvlan_tag_id)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_priorityRef_set
- * Description:
- *      Set S-VLAN upstream priority reference setting.
- * Input:
- *      ref - reference selection parameter.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameter.
- * Note:
- *      The API can set the upstream SVLAN tag priority reference source. The related priority
- *      sources are as following:
- *      - REF_INTERNAL_PRI,
- *      - REF_CTAG_PRI,
- *      - REF_SVLAN_PRI,
- *      - REF_PB_PRI.
- */
-rtk_api_ret_t rtk_svlan_priorityRef_set(rtk_svlan_pri_ref_t ref)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (ref >= REF_PRI_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicSvlanPrioritySel(ref)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_priorityRef_get
- * Description:
- *      Get S-VLAN upstream priority reference setting.
- * Input:
- *      None
- * Output:
- *      pRef - reference selection parameter.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      The API can get the upstream SVLAN tag priority reference source. The related priority
- *      sources are as following:
- *      - REF_INTERNAL_PRI,
- *      - REF_CTAG_PRI,
- *      - REF_SVLAN_PRI,
- *      - REF_PB_PRI
- */
-rtk_api_ret_t rtk_svlan_priorityRef_get(rtk_svlan_pri_ref_t *pRef)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pRef)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSvlanPrioritySel(pRef)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_set
- * Description:
- *      Configure system SVLAN member content
- * Input:
- *      svid - SVLAN id
- *      psvlan_cfg - SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameter.
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_SVLAN_TABLE_FULL - SVLAN configuration is full.
- * Note:
- *      The API can set system 64 accepted s-tag frame format. Only 64 SVID S-tag frame will be accpeted
- *      to receiving from uplink ports. Other SVID S-tag frame or S-untagged frame will be droped by default setup.
- *      - rtk_svlan_memberCfg_t->svid is SVID of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->memberport is member port mask of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->fid is filtering database of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->priority is priority of SVLAN member configuration.
- */
-rtk_api_ret_t rtk_svlan_memberPortEntry_set(rtk_vlan_t svid, rtk_svlan_memberCfg_t *pSvlan_cfg)
-{
-    rtk_api_ret_t retVal;
-    rtk_int32 i;
-    rtk_uint32 empty_idx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtk_uint32 phyMbrPmask;
-    rtk_vlan_cfg_t vlanCfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvlan_cfg)
-        return RT_ERR_NULL_POINTER;
-
-    if(svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    RTK_CHK_PORTMASK_VALID(&(pSvlan_cfg->memberport));
-
-    RTK_CHK_PORTMASK_VALID(&(pSvlan_cfg->untagport));
-
-    if (pSvlan_cfg->fiden > ENABLED)
-        return RT_ERR_ENABLE;
-
-    if (pSvlan_cfg->fid > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    if (pSvlan_cfg->priority > RTL8367C_PRIMAX)
-        return RT_ERR_VLAN_PRIORITY;
-
-    if (pSvlan_cfg->efiden > ENABLED)
-        return RT_ERR_ENABLE;
-
-    if (pSvlan_cfg->efid > RTL8367C_EFIDMAX)
-        return RT_ERR_L2_FID;
-
-    if(SVLAN_LOOKUP_C4KVLAN == svlan_lookupType)
-    {
-        if ((retVal = rtk_vlan_get(svid, &vlanCfg)) != RT_ERR_OK)
-            return retVal;
-
-        vlanCfg.mbr = pSvlan_cfg->memberport;
-        vlanCfg.untag = pSvlan_cfg->untagport;
-
-        if ((retVal = rtk_vlan_set(svid, &vlanCfg)) != RT_ERR_OK)
-            return retVal;
-
-        empty_idx = 0xFF;
-
-        for (i = 0; i<= RTL8367C_SVIDXMAX; i++)
-        {
-            if (svid == svlan_mbrCfgVid[i] && TRUE == svlan_mbrCfgUsage[i])
-            {
-                memset(&svlanMemConf, 0, sizeof(rtl8367c_svlan_memconf_t));
-                svlanMemConf.vs_svid        = svid;
-                svlanMemConf.vs_efiden      = pSvlan_cfg->efiden;
-                svlanMemConf.vs_efid        = pSvlan_cfg->efid;
-                svlanMemConf.vs_priority    = pSvlan_cfg->priority;
-
-                /*for create check*/
-                if(0 == svlanMemConf.vs_efiden && 0 == svlanMemConf.vs_efid)
-                    svlanMemConf.vs_efid = 1;
-
-                if ((retVal = rtl8367c_setAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-                    return retVal;
-
-                return RT_ERR_OK;
-            }
-            else if (FALSE == svlan_mbrCfgUsage[i] && 0xFF == empty_idx)
-            {
-                empty_idx = i;
-            }
-        }
-
-        if (empty_idx != 0xFF)
-        {
-            svlan_mbrCfgUsage[empty_idx] = TRUE;
-            svlan_mbrCfgVid[empty_idx] = svid;
-
-            memset(&svlanMemConf, 0, sizeof(rtl8367c_svlan_memconf_t));
-            svlanMemConf.vs_svid        = svid;
-            svlanMemConf.vs_efiden      = pSvlan_cfg->efiden;
-            svlanMemConf.vs_efid        = pSvlan_cfg->efid;
-            svlanMemConf.vs_priority    = pSvlan_cfg->priority;
-
-            /*for create check*/
-            if(0 == svlanMemConf.vs_efiden && 0 == svlanMemConf.vs_efid)
-                svlanMemConf.vs_efid = 1;
-
-            if ((retVal = rtl8367c_setAsicSvlanMemberConfiguration(empty_idx, &svlanMemConf)) != RT_ERR_OK)
-                return retVal;
-
-        }
-
-        return RT_ERR_OK;
-    }
-
-
-    empty_idx = 0xFF;
-
-    for (i = 0; i<= RTL8367C_SVIDXMAX; i++)
-    {
-        /*
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-        */
-        if (svid == svlan_mbrCfgVid[i] && TRUE == svlan_mbrCfgUsage[i])
-        {
-            svlanMemConf.vs_svid = svid;
-
-            if(rtk_switch_portmask_L2P_get(&(pSvlan_cfg->memberport), &phyMbrPmask) != RT_ERR_OK)
-                return RT_ERR_FAILED;
-
-            svlanMemConf.vs_member = phyMbrPmask;
-
-            if(rtk_switch_portmask_L2P_get(&(pSvlan_cfg->untagport), &phyMbrPmask) != RT_ERR_OK)
-                return RT_ERR_FAILED;
-
-            svlanMemConf.vs_untag = phyMbrPmask;
-
-            svlanMemConf.vs_force_fid   = pSvlan_cfg->fiden;
-            svlanMemConf.vs_fid_msti    = pSvlan_cfg->fid;
-            svlanMemConf.vs_priority    = pSvlan_cfg->priority;
-            svlanMemConf.vs_efiden      = pSvlan_cfg->efiden;
-            svlanMemConf.vs_efid        = pSvlan_cfg->efid;
-
-            /*all items are reset means deleting*/
-            if( 0 == svlanMemConf.vs_member &&
-                0 == svlanMemConf.vs_untag &&
-                0 == svlanMemConf.vs_force_fid &&
-                0 == svlanMemConf.vs_fid_msti &&
-                0 == svlanMemConf.vs_priority &&
-                0 == svlanMemConf.vs_efiden &&
-                0 == svlanMemConf.vs_efid)
-            {
-                svlan_mbrCfgUsage[i] = FALSE;
-                svlan_mbrCfgVid[i] = 0;
-
-                /* Clear SVID also */
-                svlanMemConf.vs_svid = 0;
-            }
-            else
-            {
-                svlan_mbrCfgUsage[i] = TRUE;
-                svlan_mbrCfgVid[i] = svlanMemConf.vs_svid;
-
-                if(0 == svlanMemConf.vs_svid)
-                {
-                    /*for create check*/
-                    if(0 == svlanMemConf.vs_efiden && 0 == svlanMemConf.vs_efid)
-                    {
-                        svlanMemConf.vs_efid = 1;
-                    }
-                }
-            }
-
-            if ((retVal = rtl8367c_setAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-                return retVal;
-
-            return RT_ERR_OK;
-        }
-        else if (FALSE == svlan_mbrCfgUsage[i] && 0xFF == empty_idx)
-        {
-            empty_idx = i;
-        }
-    }
-
-    if (empty_idx != 0xFF)
-    {
-        memset(&svlanMemConf, 0, sizeof(rtl8367c_svlan_memconf_t));
-        svlanMemConf.vs_svid = svid;
-
-        if(rtk_switch_portmask_L2P_get(&(pSvlan_cfg->memberport), &phyMbrPmask) != RT_ERR_OK)
-            return RT_ERR_FAILED;
-
-        svlanMemConf.vs_member = phyMbrPmask;
-
-        if(rtk_switch_portmask_L2P_get(&(pSvlan_cfg->untagport), &phyMbrPmask) != RT_ERR_OK)
-            return RT_ERR_FAILED;
-
-        svlanMemConf.vs_untag = phyMbrPmask;
-
-        svlanMemConf.vs_force_fid   = pSvlan_cfg->fiden;
-        svlanMemConf.vs_fid_msti    = pSvlan_cfg->fid;
-        svlanMemConf.vs_priority    = pSvlan_cfg->priority;
-
-        svlanMemConf.vs_efiden      = pSvlan_cfg->efiden;
-        svlanMemConf.vs_efid        = pSvlan_cfg->efid;
-
-        /*change efid for empty svid 0*/
-        if(0 == svlanMemConf.vs_svid)
-        {   /*for create check*/
-            if(0 == svlanMemConf.vs_efiden && 0 == svlanMemConf.vs_efid)
-            {
-                svlanMemConf.vs_efid = 1;
-            }
-        }
-
-        svlan_mbrCfgUsage[empty_idx] = TRUE;
-        svlan_mbrCfgVid[empty_idx] = svlanMemConf.vs_svid;
-
-        if ((retVal = rtl8367c_setAsicSvlanMemberConfiguration(empty_idx, &svlanMemConf)) != RT_ERR_OK)
-        {
-            return retVal;
-        }
-
-        return RT_ERR_OK;
-    }
-
-    return RT_ERR_SVLAN_TABLE_FULL;
-}
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_get
- * Description:
- *      Get SVLAN member Configure.
- * Input:
- *      svid - SVLAN id
- * Output:
- *      pSvlan_cfg - SVLAN member configuration
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can get system 64 accepted s-tag frame format. Only 64 SVID S-tag frame will be accpeted
- *      to receiving from uplink ports. Other SVID S-tag frame or S-untagged frame will be droped.
- */
-rtk_api_ret_t rtk_svlan_memberPortEntry_get(rtk_vlan_t svid, rtk_svlan_memberCfg_t *pSvlan_cfg)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvlan_cfg)
-        return RT_ERR_NULL_POINTER;
-
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-
-    for (i = 0; i<= RTL8367C_SVIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            pSvlan_cfg->svid        = svlanMemConf.vs_svid;
-
-            if(rtk_switch_portmask_P2L_get(svlanMemConf.vs_member,&(pSvlan_cfg->memberport)) != RT_ERR_OK)
-                return RT_ERR_FAILED;
-
-            if(rtk_switch_portmask_P2L_get(svlanMemConf.vs_untag,&(pSvlan_cfg->untagport)) != RT_ERR_OK)
-                return RT_ERR_FAILED;
-
-            pSvlan_cfg->fiden       = svlanMemConf.vs_force_fid;
-            pSvlan_cfg->fid         = svlanMemConf.vs_fid_msti;
-            pSvlan_cfg->priority    = svlanMemConf.vs_priority;
-            pSvlan_cfg->efiden      = svlanMemConf.vs_efiden;
-            pSvlan_cfg->efid        = svlanMemConf.vs_efid;
-
-            return RT_ERR_OK;
-        }
-    }
-
-    return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-
-}
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_adv_set
- * Description:
- *      Configure system SVLAN member by index
- * Input:
- *      idx         - Index (0 ~ 63)
- *      psvlan_cfg  - SVLAN member configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameter.
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_PORT_MASK        - Invalid portmask.
- *      RT_ERR_SVLAN_TABLE_FULL - SVLAN configuration is full.
- * Note:
- *      The API can set system 64 accepted s-tag frame format by index.
- *      - rtk_svlan_memberCfg_t->svid is SVID of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->memberport is member port mask of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->fid is filtering database of SVLAN member configuration.
- *      - rtk_svlan_memberCfg_t->priority is priority of SVLAN member configuration.
- */
-rtk_api_ret_t rtk_svlan_memberPortEntry_adv_set(rtk_uint32 idx, rtk_svlan_memberCfg_t *pSvlan_cfg)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtk_uint32 phyMbrPmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvlan_cfg)
-        return RT_ERR_NULL_POINTER;
-
-    if (idx > RTL8367C_SVIDXMAX)
-        return RT_ERR_SVLAN_ENTRY_INDEX;
-
-    if (pSvlan_cfg->svid>RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    RTK_CHK_PORTMASK_VALID(&(pSvlan_cfg->memberport));
-
-    RTK_CHK_PORTMASK_VALID(&(pSvlan_cfg->untagport));
-
-    if (pSvlan_cfg->fiden > ENABLED)
-        return RT_ERR_ENABLE;
-
-    if (pSvlan_cfg->fid > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    if (pSvlan_cfg->priority > RTL8367C_PRIMAX)
-        return RT_ERR_VLAN_PRIORITY;
-
-    if (pSvlan_cfg->efiden > ENABLED)
-        return RT_ERR_ENABLE;
-
-    if (pSvlan_cfg->efid > RTL8367C_EFIDMAX)
-        return RT_ERR_L2_FID;
-
-    memset(&svlanMemConf, 0, sizeof(rtl8367c_svlan_memconf_t));
-    svlanMemConf.vs_svid        = pSvlan_cfg->svid;
-    if(rtk_switch_portmask_L2P_get(&(pSvlan_cfg->memberport), &phyMbrPmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    svlanMemConf.vs_member = phyMbrPmask;
-
-    if(rtk_switch_portmask_L2P_get(&(pSvlan_cfg->untagport), &phyMbrPmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    svlanMemConf.vs_untag = phyMbrPmask;
-
-
-    svlanMemConf.vs_force_fid   = pSvlan_cfg->fiden;
-    svlanMemConf.vs_fid_msti    = pSvlan_cfg->fid;
-    svlanMemConf.vs_priority    = pSvlan_cfg->priority;
-    svlanMemConf.vs_efiden      = pSvlan_cfg->efiden;
-    svlanMemConf.vs_efid        = pSvlan_cfg->efid;
-
-    if(0 == svlanMemConf.vs_svid &&
-        0 == svlanMemConf.vs_member &&
-        0 == svlanMemConf.vs_untag &&
-        0 == svlanMemConf.vs_force_fid &&
-        0 == svlanMemConf.vs_fid_msti &&
-        0 == svlanMemConf.vs_priority &&
-        0 == svlanMemConf.vs_efiden &&
-        0 == svlanMemConf.vs_efid)
-    {
-        svlan_mbrCfgUsage[idx] = FALSE;
-        svlan_mbrCfgVid[idx] = 0;
-    }
-    else
-    {
-        svlan_mbrCfgUsage[idx] = TRUE;
-        svlan_mbrCfgVid[idx] = svlanMemConf.vs_svid;
-    }
-
-    if ((retVal = rtl8367c_setAsicSvlanMemberConfiguration(idx, &svlanMemConf)) != RT_ERR_OK)
-        return retVal;
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_memberPortEntry_adv_get
- * Description:
- *      Get SVLAN member Configure by index.
- * Input:
- *      idx         - Index (0 ~ 63)
- * Output:
- *      pSvlan_cfg  - SVLAN member configuration
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can get system 64 accepted s-tag frame format. Only 64 SVID S-tag frame will be accpeted
- *      to receiving from uplink ports. Other SVID S-tag frame or S-untagged frame will be droped.
- */
-rtk_api_ret_t rtk_svlan_memberPortEntry_adv_get(rtk_uint32 idx, rtk_svlan_memberCfg_t *pSvlan_cfg)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvlan_cfg)
-        return RT_ERR_NULL_POINTER;
-
-    if (idx > RTL8367C_SVIDXMAX)
-        return RT_ERR_SVLAN_ENTRY_INDEX;
-
-    if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(idx, &svlanMemConf)) != RT_ERR_OK)
-        return retVal;
-
-    pSvlan_cfg->svid        = svlanMemConf.vs_svid;
-    if(rtk_switch_portmask_P2L_get(svlanMemConf.vs_member,&(pSvlan_cfg->memberport)) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    if(rtk_switch_portmask_P2L_get(svlanMemConf.vs_untag,&(pSvlan_cfg->untagport)) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    pSvlan_cfg->fiden       = svlanMemConf.vs_force_fid;
-    pSvlan_cfg->fid         = svlanMemConf.vs_fid_msti;
-    pSvlan_cfg->priority    = svlanMemConf.vs_priority;
-    pSvlan_cfg->efiden      = svlanMemConf.vs_efiden;
-    pSvlan_cfg->efid        = svlanMemConf.vs_efid;
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_svlan_defaultSvlan_set
- * Description:
- *      Configure default egress SVLAN.
- * Input:
- *      port - Source port
- *      svid - SVLAN id
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_INPUT                    - Invalid input parameter.
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- * Note:
- *      The API can set port n S-tag format index while receiving frame from port n
- *      is transmit through uplink port with s-tag field
- */
-rtk_api_ret_t rtk_svlan_defaultSvlan_set(rtk_port_t port, rtk_vlan_t svid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    /* svid must be 0~4095 */
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    for (i = 0; i < RTL8367C_SVIDXNO; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            if ((retVal = rtl8367c_setAsicSvlanDefaultVlan(rtk_switch_port_L2P_get(port), i)) != RT_ERR_OK)
-                return retVal;
-
-            return RT_ERR_OK;
-        }
-    }
-
-    return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-}
-
-/* Function Name:
- *      rtk_svlan_defaultSvlan_get
- * Description:
- *      Get the configure default egress SVLAN.
- * Input:
- *      port - Source port
- * Output:
- *      pSvid - SVLAN VID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can get port n S-tag format index while receiving frame from port n
- *      is transmit through uplink port with s-tag field
- */
-rtk_api_ret_t rtk_svlan_defaultSvlan_get(rtk_port_t port, rtk_vlan_t *pSvid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 idx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvid)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicSvlanDefaultVlan(rtk_switch_port_L2P_get(port), &idx)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(idx, &svlanMemConf)) != RT_ERR_OK)
-        return retVal;
-
-    *pSvid = svlanMemConf.vs_svid;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_c2s_add
- * Description:
- *      Configure SVLAN C2S table
- * Input:
- *      vid - VLAN ID
- *      src_port - Ingress Port
- *      svid - SVLAN VID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port ID.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can set system C2S configuration. ASIC will check upstream's VID and assign related
- *      SVID to mathed packet. There are 128 SVLAN C2S configurations.
- */
-rtk_api_ret_t rtk_svlan_c2s_add(rtk_vlan_t vid, rtk_port_t src_port, rtk_vlan_t svid)
-{
-    rtk_api_ret_t retVal, i;
-    rtk_uint32 empty_idx;
-    rtk_uint32 evid, pmsk, svidx, c2s_svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtk_port_t phyPort;
-    rtk_uint16 doneFlag;
-
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(src_port);
-
-    phyPort = rtk_switch_port_L2P_get(src_port);
-
-    empty_idx = 0xFFFF;
-    svidx = 0xFFFF;
-    doneFlag = FALSE;
-
-    for (i = 0; i<= RTL8367C_SVIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            svidx = i;
-            break;
-        }
-    }
-
-    if (0xFFFF == svidx)
-        return RT_ERR_SVLAN_VID;
-
-    for (i=RTL8367C_C2SIDXMAX; i>=0; i--)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanC2SConf(i, &evid, &pmsk, &c2s_svidx)) != RT_ERR_OK)
-                return retVal;
-
-        if (evid == vid)
-        {
-            /* Check Src_port */
-            if(pmsk & (1 << phyPort))
-            {
-                /* Check SVIDX */
-                if(c2s_svidx == svidx)
-                {
-                    /* All the same, do nothing */
-                }
-                else
-                {
-                    /* New svidx, remove src_port and find a new slot to add a new enrty */
-                    pmsk = pmsk & ~(1 << phyPort);
-                    if(pmsk == 0)
-                        c2s_svidx = 0;
-
-                    if ((retVal = rtl8367c_setAsicSvlanC2SConf(i, vid, pmsk, c2s_svidx)) != RT_ERR_OK)
-                        return retVal;
-                }
-            }
-            else
-            {
-                if(c2s_svidx == svidx && doneFlag == FALSE)
-                {
-                    pmsk = pmsk | (1 << phyPort);
-                    if ((retVal = rtl8367c_setAsicSvlanC2SConf(i, vid, pmsk, svidx)) != RT_ERR_OK)
-                        return retVal;
-
-                    doneFlag = TRUE;
-                }
-            }
-        }
-        else if (evid==0&&pmsk==0)
-        {
-            empty_idx = i;
-        }
-    }
-
-    if (0xFFFF != empty_idx && doneFlag ==FALSE)
-    {
-       if ((retVal = rtl8367c_setAsicSvlanC2SConf(empty_idx, vid, (1<<phyPort), svidx)) != RT_ERR_OK)
-           return retVal;
-
-       return RT_ERR_OK;
-    }
-    else if(doneFlag == TRUE)
-    {
-        return RT_ERR_OK;
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_c2s_del
- * Description:
- *      Delete one C2S entry
- * Input:
- *      vid - VLAN ID
- *      src_port - Ingress Port
- *      svid - SVLAN VID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_VLAN_VID         - Invalid VID parameter.
- *      RT_ERR_PORT_ID          - Invalid port ID.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can delete system C2S configuration. There are 128 SVLAN C2S configurations.
- */
-rtk_api_ret_t rtk_svlan_c2s_del(rtk_vlan_t vid, rtk_port_t src_port)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtk_uint32 evid, pmsk, svidx;
-    rtk_port_t phyPort;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (vid > RTL8367C_EVIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(src_port);
-    phyPort = rtk_switch_port_L2P_get(src_port);
-
-    for (i = 0; i <= RTL8367C_C2SIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanC2SConf(i, &evid, &pmsk, &svidx)) != RT_ERR_OK)
-            return retVal;
-
-        if (evid == vid)
-        {
-            if(pmsk & (1 << phyPort))
-            {
-                pmsk = pmsk & ~(1 << phyPort);
-                if(pmsk == 0)
-                {
-                    vid = 0;
-                    svidx = 0;
-                }
-
-                if ((retVal = rtl8367c_setAsicSvlanC2SConf(i, vid, pmsk, svidx)) != RT_ERR_OK)
-                    return retVal;
-
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_c2s_get
- * Description:
- *      Get configure SVLAN C2S table
- * Input:
- *      vid - VLAN ID
- *      src_port - Ingress Port
- * Output:
- *      pSvid - SVLAN ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port ID.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- * Note:
- *     The API can get system C2S configuration. There are 128 SVLAN C2S configurations.
- */
-rtk_api_ret_t rtk_svlan_c2s_get(rtk_vlan_t vid, rtk_port_t src_port, rtk_vlan_t *pSvid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtk_uint32 evid, pmsk, svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtk_port_t phyPort;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvid)
-        return RT_ERR_NULL_POINTER;
-
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(src_port);
-    phyPort = rtk_switch_port_L2P_get(src_port);
-
-    for (i = 0; i <= RTL8367C_C2SIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanC2SConf(i, &evid, &pmsk, &svidx)) != RT_ERR_OK)
-            return retVal;
-
-        if (evid == vid)
-        {
-            if(pmsk & (1 << phyPort))
-            {
-                if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(svidx, &svlanMemConf)) != RT_ERR_OK)
-                    return retVal;
-
-                *pSvid = svlanMemConf.vs_svid;
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_untag_action_set
- * Description:
- *      Configure Action of downstream UnStag packet
- * Input:
- *      action  - Action for UnStag
- *      svid    - The SVID assigned to UnStag packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can configure action of downstream Un-Stag packet. A SVID assigned
- *      to the un-stag is also supported by this API. The parameter of svid is
- *      only referenced when the action is set to UNTAG_ASSIGN
- */
-rtk_api_ret_t rtk_svlan_untag_action_set(rtk_svlan_untag_action_t action, rtk_vlan_t svid)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      i;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (action >= UNTAG_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if(action == UNTAG_ASSIGN)
-    {
-        if (svid > RTL8367C_VIDMAX)
-            return RT_ERR_SVLAN_VID;
-    }
-
-    if ((retVal = rtl8367c_setAsicSvlanIngressUntag((rtk_uint32)action)) != RT_ERR_OK)
-        return retVal;
-
-    if(action == UNTAG_ASSIGN)
-    {
-        for (i = 0; i < RTL8367C_SVIDXNO; i++)
-        {
-            if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-                return retVal;
-
-            if (svid == svlanMemConf.vs_svid)
-            {
-                if ((retVal = rtl8367c_setAsicSvlanUntagVlan(i)) != RT_ERR_OK)
-                    return retVal;
-
-                return RT_ERR_OK;
-            }
-        }
-
-        return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_untag_action_get
- * Description:
- *      Get Action of downstream UnStag packet
- * Input:
- *      None
- * Output:
- *      pAction  - Action for UnStag
- *      pSvid    - The SVID assigned to UnStag packet
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can Get action of downstream Un-Stag packet. A SVID assigned
- *      to the un-stag is also retrieved by this API. The parameter pSvid is
- *      only refernced when the action is UNTAG_ASSIGN
- */
-rtk_api_ret_t rtk_svlan_untag_action_get(rtk_svlan_untag_action_t *pAction, rtk_vlan_t *pSvid)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction || NULL == pSvid)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSvlanIngressUntag(pAction)) != RT_ERR_OK)
-        return retVal;
-
-    if(*pAction == UNTAG_ASSIGN)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanUntagVlan(&svidx)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(svidx, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        *pSvid = svlanMemConf.vs_svid;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_unmatch_action_set
- * Description:
- *      Configure Action of downstream Unmatch packet
- * Input:
- *      action  - Action for Unmatch
- *      svid    - The SVID assigned to Unmatch packet
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can configure action of downstream Un-match packet. A SVID assigned
- *      to the un-match is also supported by this API. The parameter od svid is
- *      only refernced when the action is set to UNMATCH_ASSIGN
- */
-rtk_api_ret_t rtk_svlan_unmatch_action_set(rtk_svlan_unmatch_action_t action, rtk_vlan_t svid)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      i;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (action >= UNMATCH_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if (action == UNMATCH_ASSIGN)
-    {
-        if (svid > RTL8367C_VIDMAX)
-            return RT_ERR_SVLAN_VID;
-    }
-
-    if ((retVal = rtl8367c_setAsicSvlanIngressUnmatch((rtk_uint32)action)) != RT_ERR_OK)
-        return retVal;
-
-    if(action == UNMATCH_ASSIGN)
-    {
-        for (i = 0; i < RTL8367C_SVIDXNO; i++)
-        {
-            if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-                return retVal;
-
-            if (svid == svlanMemConf.vs_svid)
-            {
-                if ((retVal = rtl8367c_setAsicSvlanUnmatchVlan(i)) != RT_ERR_OK)
-                    return retVal;
-
-                return RT_ERR_OK;
-            }
-        }
-
-        return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_unmatch_action_get
- * Description:
- *      Get Action of downstream Unmatch packet
- * Input:
- *      None
- * Output:
- *      pAction  - Action for Unmatch
- *      pSvid    - The SVID assigned to Unmatch packet
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can Get action of downstream Un-match packet. A SVID assigned
- *      to the un-match is also retrieved by this API. The parameter pSvid is
- *      only refernced when the action is UNMATCH_ASSIGN
- */
-rtk_api_ret_t rtk_svlan_unmatch_action_get(rtk_svlan_unmatch_action_t *pAction, rtk_vlan_t *pSvid)
-{
-    rtk_api_ret_t   retVal;
-    rtk_uint32      svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction || NULL == pSvid)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSvlanIngressUnmatch(pAction)) != RT_ERR_OK)
-        return retVal;
-
-    if(*pAction == UNMATCH_ASSIGN)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanUnmatchVlan(&svidx)) != RT_ERR_OK)
-            return retVal;
-
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(svidx, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        *pSvid = svlanMemConf.vs_svid;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_unassign_action_set
- * Description:
- *      Configure Action of upstream without svid assign action
- * Input:
- *      action  - Action for Un-assign
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can configure action of upstream Un-assign svid packet. If action is not
- *      trap to CPU, the port-based SVID sure be assign as system need
- */
-rtk_api_ret_t rtk_svlan_unassign_action_set(rtk_svlan_unassign_action_t action)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (action >= UNASSIGN_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicSvlanEgressUnassign((rtk_uint32)action);
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtk_svlan_unassign_action_get
- * Description:
- *      Get action of upstream without svid assignment
- * Input:
- *      None
- * Output:
- *      pAction  - Action for Un-assign
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_svlan_unassign_action_get(rtk_svlan_unassign_action_t *pAction)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pAction)
-        return RT_ERR_NULL_POINTER;
-
-    retVal = rtl8367c_getAsicSvlanEgressUnassign(pAction);
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtk_svlan_dmac_vidsel_set
- * Description:
- *      Set DMAC CVID selection
- * Input:
- *      port    - Port
- *      enable  - state of DMAC CVID Selection
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      This API can set DMAC CVID Selection state
- */
-rtk_api_ret_t rtk_svlan_dmac_vidsel_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicSvlanDmacCvidSel(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-            return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_dmac_vidsel_get
- * Description:
- *      Get DMAC CVID selection
- * Input:
- *      port    - Port
- * Output:
- *      pEnable - state of DMAC CVID Selection
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      This API can get DMAC CVID Selection state
- */
-rtk_api_ret_t rtk_svlan_dmac_vidsel_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if ((retVal = rtl8367c_getAsicSvlanDmacCvidSel(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-            return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_svlan_ipmc2s_add
- * Description:
- *      add ip multicast address to SVLAN
- * Input:
- *      svid    - SVLAN VID
- *      ipmc    - ip multicast address
- *      ipmcMsk - ip multicast mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can set IP mutlicast to SVID configuration. If upstream packet is IPv4 multicast
- *      packet and DIP is matched MC2S configuration, ASIC will assign egress SVID to the packet.
- *      There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-rtk_api_ret_t rtk_svlan_ipmc2s_add(ipaddr_t ipmc, ipaddr_t ipmcMsk,rtk_vlan_t svid)
-{
-    rtk_api_ret_t retVal, i;
-    rtk_uint32 empty_idx;
-    rtk_uint32 svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_mc2s_t svlanMC2SConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    if ((ipmc&0xF0000000)!=0xE0000000)
-        return RT_ERR_INPUT;
-
-    svidx = 0xFFFF;
-
-    for (i = 0; i < RTL8367C_SVIDXNO; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            svidx = i;
-            break;
-        }
-    }
-
-    if (0xFFFF == svidx)
-            return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-
-
-    empty_idx = 0xFFFF;
-
-    for (i = RTL8367C_MC2SIDXMAX; i >= 0; i--)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (TRUE == svlanMC2SConf.valid)
-        {
-            if (svlanMC2SConf.format == SVLAN_MC2S_MODE_IP &&
-                svlanMC2SConf.sdata==ipmc&&
-                svlanMC2SConf.smask==ipmcMsk)
-            {
-                svlanMC2SConf.svidx = svidx;
-                if ((retVal = rtl8367c_setAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-                    return retVal;
-            }
-        }
-        else
-        {
-            empty_idx = i;
-        }
-    }
-
-    if (empty_idx!=0xFFFF)
-    {
-        svlanMC2SConf.valid = TRUE;
-        svlanMC2SConf.svidx = svidx;
-        svlanMC2SConf.format = SVLAN_MC2S_MODE_IP;
-        svlanMC2SConf.sdata = ipmc;
-        svlanMC2SConf.smask = ipmcMsk;
-        if ((retVal = rtl8367c_setAsicSvlanMC2SConf(empty_idx, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-        return RT_ERR_OK;
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-
-}
-
-/* Function Name:
- *      rtk_svlan_ipmc2s_del
- * Description:
- *      delete ip multicast address to SVLAN
- * Input:
- *      ipmc    - ip multicast address
- *      ipmcMsk - ip multicast mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can delete IP mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-rtk_api_ret_t rtk_svlan_ipmc2s_del(ipaddr_t ipmc, ipaddr_t ipmcMsk)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtl8367c_svlan_mc2s_t svlanMC2SConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((ipmc&0xF0000000)!=0xE0000000)
-        return RT_ERR_INPUT;
-
-    for (i = 0; i <= RTL8367C_MC2SIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (TRUE == svlanMC2SConf.valid)
-        {
-            if (svlanMC2SConf.format == SVLAN_MC2S_MODE_IP &&
-                svlanMC2SConf.sdata==ipmc&&
-                svlanMC2SConf.smask==ipmcMsk)
-            {
-                memset(&svlanMC2SConf, 0, sizeof(rtl8367c_svlan_mc2s_t));
-                if ((retVal = rtl8367c_setAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-                    return retVal;
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_ipmc2s_get
- * Description:
- *      Get ip multicast address to SVLAN
- * Input:
- *      ipmc    - ip multicast address
- *      ipmcMsk - ip multicast mask
- * Output:
- *      pSvid - SVLAN VID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- * Note:
- *      The API can get IP mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-rtk_api_ret_t rtk_svlan_ipmc2s_get(ipaddr_t ipmc, ipaddr_t ipmcMsk, rtk_vlan_t *pSvid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_mc2s_t svlanMC2SConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvid)
-        return RT_ERR_NULL_POINTER;
-
-    if ((ipmc&0xF0000000)!=0xE0000000)
-        return RT_ERR_INPUT;
-
-    for (i = 0; i <= RTL8367C_MC2SIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (TRUE == svlanMC2SConf.valid &&
-            svlanMC2SConf.format == SVLAN_MC2S_MODE_IP &&
-            svlanMC2SConf.sdata == ipmc &&
-            svlanMC2SConf.smask == ipmcMsk)
-        {
-            if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(svlanMC2SConf.svidx, &svlanMemConf)) != RT_ERR_OK)
-                return retVal;
-            *pSvid = svlanMemConf.vs_svid;
-            return RT_ERR_OK;
-        }
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_l2mc2s_add
- * Description:
- *      Add L2 multicast address to SVLAN
- * Input:
- *      mac     - L2 multicast address
- *      macMsk  - L2 multicast address mask
- *      svid    - SVLAN VID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_SVLAN_VID                - Invalid SVLAN VID parameter.
- *      RT_ERR_SVLAN_ENTRY_NOT_FOUND    - specified svlan entry not found.
- *      RT_ERR_OUT_OF_RANGE             - input out of range.
- *      RT_ERR_INPUT                    - Invalid input parameters.
- * Note:
- *      The API can set L2 Mutlicast to SVID configuration. If upstream packet is L2 multicast
- *      packet and DMAC is matched, ASIC will assign egress SVID to the packet. There are 32
- *      SVLAN multicast configurations for IP and L2 multicast.
- */
-rtk_api_ret_t rtk_svlan_l2mc2s_add(rtk_mac_t mac, rtk_mac_t macMsk, rtk_vlan_t svid)
-{
-    rtk_api_ret_t retVal, i;
-    rtk_uint32 empty_idx;
-    rtk_uint32 svidx, l2add, l2Mask;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_mc2s_t svlanMC2SConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    if (mac.octet[0]!= 1&&mac.octet[1]!=0)
-        return RT_ERR_INPUT;
-
-    l2add = (mac.octet[2] << 24) | (mac.octet[3] << 16) | (mac.octet[4] << 8) | mac.octet[5];
-    l2Mask = (macMsk.octet[2] << 24) | (macMsk.octet[3] << 16) | (macMsk.octet[4] << 8) | macMsk.octet[5];
-
-    svidx = 0xFFFF;
-
-    for (i = 0; i < RTL8367C_SVIDXNO; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            svidx = i;
-            break;
-        }
-    }
-
-    if (0xFFFF == svidx)
-        return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-
-    empty_idx = 0xFFFF;
-
-    for (i = RTL8367C_MC2SIDXMAX; i >=0; i--)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (TRUE == svlanMC2SConf.valid)
-        {
-            if (svlanMC2SConf.format == SVLAN_MC2S_MODE_MAC &&
-                svlanMC2SConf.sdata==l2add&&
-                svlanMC2SConf.smask==l2Mask)
-            {
-                svlanMC2SConf.svidx = svidx;
-                if ((retVal = rtl8367c_setAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-                    return retVal;
-            }
-        }
-        else
-        {
-            empty_idx = i;
-        }
-    }
-
-    if (empty_idx!=0xFFFF)
-    {
-        svlanMC2SConf.valid = TRUE;
-        svlanMC2SConf.svidx = svidx;
-        svlanMC2SConf.format = SVLAN_MC2S_MODE_MAC;
-        svlanMC2SConf.sdata = l2add;
-        svlanMC2SConf.smask = l2Mask;
-
-        if ((retVal = rtl8367c_setAsicSvlanMC2SConf(empty_idx, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-        return RT_ERR_OK;
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_l2mc2s_del
- * Description:
- *      delete L2 multicast address to SVLAN
- * Input:
- *      mac     - L2 multicast address
- *      macMsk  - L2 multicast address mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_SVLAN_VID        - Invalid SVLAN VID parameter.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can delete Mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-rtk_api_ret_t rtk_svlan_l2mc2s_del(rtk_mac_t mac, rtk_mac_t macMsk)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtk_uint32 l2add, l2Mask;
-    rtl8367c_svlan_mc2s_t svlanMC2SConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (mac.octet[0]!= 1&&mac.octet[1]!=0)
-        return RT_ERR_INPUT;
-
-    l2add = (mac.octet[2] << 24) | (mac.octet[3] << 16) | (mac.octet[4] << 8) | mac.octet[5];
-    l2Mask = (macMsk.octet[2] << 24) | (macMsk.octet[3] << 16) | (macMsk.octet[4] << 8) | macMsk.octet[5];
-
-    for (i = 0; i <= RTL8367C_MC2SIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (TRUE == svlanMC2SConf.valid)
-        {
-            if (svlanMC2SConf.format == SVLAN_MC2S_MODE_MAC &&
-                svlanMC2SConf.sdata==l2add&&
-                svlanMC2SConf.smask==l2Mask)
-            {
-                memset(&svlanMC2SConf, 0, sizeof(rtl8367c_svlan_mc2s_t));
-                if ((retVal = rtl8367c_setAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-                    return retVal;
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_l2mc2s_get
- * Description:
- *      Get L2 multicast address to SVLAN
- * Input:
- *      mac     - L2 multicast address
- *      macMsk  - L2 multicast address mask
- * Output:
- *      pSvid - SVLAN VID
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_INPUT            - Invalid input parameters.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The API can get L2 mutlicast to SVID configuration. There are 32 SVLAN multicast configurations for IP and L2 multicast.
- */
-rtk_api_ret_t rtk_svlan_l2mc2s_get(rtk_mac_t mac, rtk_mac_t macMsk, rtk_vlan_t *pSvid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtk_uint32 l2add,l2Mask;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_mc2s_t svlanMC2SConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pSvid)
-        return RT_ERR_NULL_POINTER;
-
-    if (mac.octet[0]!= 1&&mac.octet[1]!=0)
-        return RT_ERR_INPUT;
-
-    l2add = (mac.octet[2] << 24) | (mac.octet[3] << 16) | (mac.octet[4] << 8) | mac.octet[5];
-    l2Mask = (macMsk.octet[2] << 24) | (macMsk.octet[3] << 16) | (macMsk.octet[4] << 8) | macMsk.octet[5];
-
-    for (i = 0; i <= RTL8367C_MC2SIDXMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMC2SConf(i, &svlanMC2SConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (TRUE == svlanMC2SConf.valid)
-        {
-            if (svlanMC2SConf.format == SVLAN_MC2S_MODE_MAC &&
-                svlanMC2SConf.sdata==l2add&&
-                svlanMC2SConf.smask==l2Mask)
-            {
-                if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(svlanMC2SConf.svidx, &svlanMemConf)) != RT_ERR_OK)
-                    return retVal;
-                *pSvid = svlanMemConf.vs_svid;
-
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_sp2c_add
- * Description:
- *      Add system SP2C configuration
- * Input:
- *      cvid        - VLAN ID
- *      dst_port    - Destination port of SVLAN to CVLAN configuration
- *      svid        - SVLAN VID
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      The API can add SVID & Destination Port to CVLAN configuration. The downstream frames with assigned
- *      SVID will be add C-tag with assigned CVID if the output port is the assigned destination port.
- *      There are 128 SP2C configurations.
- */
-rtk_api_ret_t rtk_svlan_sp2c_add(rtk_vlan_t svid, rtk_port_t dst_port, rtk_vlan_t cvid)
-{
-    rtk_api_ret_t retVal, i;
-    rtk_uint32 empty_idx, svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_s2c_t svlanSP2CConf;
-    rtk_port_t port;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    if (cvid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(dst_port);
-    port = rtk_switch_port_L2P_get(dst_port);
-
-    svidx = 0xFFFF;
-
-    for (i = 0; i < RTL8367C_SVIDXNO; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            svidx = i;
-            break;
-        }
-    }
-
-    if (0xFFFF == svidx)
-        return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-
-    empty_idx = 0xFFFF;
-
-    for (i=RTL8367C_SP2CMAX; i >=0 ; i--)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanSP2CConf(i, &svlanSP2CConf)) != RT_ERR_OK)
-            return retVal;
-
-        if ( (svlanSP2CConf.svidx == svidx) && (svlanSP2CConf.dstport == port) && (svlanSP2CConf.valid == 1))
-        {
-            empty_idx = i;
-            break;
-        }
-        else if (svlanSP2CConf.valid == 0)
-        {
-            empty_idx = i;
-        }
-    }
-
-    if (empty_idx!=0xFFFF)
-    {
-        svlanSP2CConf.valid     = 1;
-        svlanSP2CConf.vid       = cvid;
-        svlanSP2CConf.svidx     = svidx;
-        svlanSP2CConf.dstport   = port;
-
-        if ((retVal = rtl8367c_setAsicSvlanSP2CConf(empty_idx, &svlanSP2CConf)) != RT_ERR_OK)
-            return retVal;
-        return RT_ERR_OK;
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-
-}
-
-/* Function Name:
- *      rtk_svlan_sp2c_get
- * Description:
- *      Get configure system SP2C content
- * Input:
- *      svid        - SVLAN VID
- *      dst_port    - Destination port of SVLAN to CVLAN configuration
- * Output:
- *      pCvid - VLAN ID
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- * Note:
- *     The API can get SVID & Destination Port to CVLAN configuration. There are 128 SP2C configurations.
- */
-rtk_api_ret_t rtk_svlan_sp2c_get(rtk_vlan_t svid, rtk_port_t dst_port, rtk_vlan_t *pCvid)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i, svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_s2c_t svlanSP2CConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pCvid)
-        return RT_ERR_NULL_POINTER;
-
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(dst_port);
-    dst_port = rtk_switch_port_L2P_get(dst_port);
-
-    svidx = 0xFFFF;
-
-    for (i = 0; i < RTL8367C_SVIDXNO; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            svidx = i;
-            break;
-        }
-    }
-
-    if (0xFFFF == svidx)
-        return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-
-    for (i = 0; i <= RTL8367C_SP2CMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanSP2CConf(i, &svlanSP2CConf)) != RT_ERR_OK)
-            return retVal;
-
-        if ( (svlanSP2CConf.svidx == svidx) && (svlanSP2CConf.dstport == dst_port) && (svlanSP2CConf.valid == 1) )
-        {
-            *pCvid = svlanSP2CConf.vid;
-            return RT_ERR_OK;
-        }
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_sp2c_del
- * Description:
- *      Delete system SP2C configuration
- * Input:
- *      svid        - SVLAN VID
- *      dst_port    - Destination port of SVLAN to CVLAN configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_SVLAN_VID    - Invalid SVLAN VID parameter.
- *      RT_ERR_OUT_OF_RANGE - input out of range.
- * Note:
- *      The API can delete SVID & Destination Port to CVLAN configuration. There are 128 SP2C configurations.
- */
-rtk_api_ret_t rtk_svlan_sp2c_del(rtk_vlan_t svid, rtk_port_t dst_port)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i, svidx;
-    rtl8367c_svlan_memconf_t svlanMemConf;
-    rtl8367c_svlan_s2c_t svlanSP2CConf;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (svid > RTL8367C_VIDMAX)
-        return RT_ERR_SVLAN_VID;
-
-    /* Check port Valid */
-    RTK_CHK_PORT_VALID(dst_port);
-    dst_port = rtk_switch_port_L2P_get(dst_port);
-
-    svidx = 0xFFFF;
-
-    for (i = 0; i < RTL8367C_SVIDXNO; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanMemberConfiguration(i, &svlanMemConf)) != RT_ERR_OK)
-            return retVal;
-
-        if (svid == svlanMemConf.vs_svid)
-        {
-            svidx = i;
-            break;
-        }
-    }
-
-    if (0xFFFF == svidx)
-        return RT_ERR_SVLAN_ENTRY_NOT_FOUND;
-
-    for (i = 0; i <= RTL8367C_SP2CMAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicSvlanSP2CConf(i, &svlanSP2CConf)) != RT_ERR_OK)
-            return retVal;
-
-        if ( (svlanSP2CConf.svidx == svidx) && (svlanSP2CConf.dstport == dst_port) && (svlanSP2CConf.valid == 1) )
-        {
-            svlanSP2CConf.valid     = 0;
-            svlanSP2CConf.vid       = 0;
-            svlanSP2CConf.svidx     = 0;
-            svlanSP2CConf.dstport   = 0;
-
-            if ((retVal = rtl8367c_setAsicSvlanSP2CConf(i, &svlanSP2CConf)) != RT_ERR_OK)
-                return retVal;
-            return RT_ERR_OK;
-        }
-
-    }
-
-    return RT_ERR_OUT_OF_RANGE;
-}
-
-/* Function Name:
- *      rtk_svlan_lookupType_set
- * Description:
- *      Set lookup type of SVLAN
- * Input:
- *      type        - lookup type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- * Note:
- *      none
- */
-rtk_api_ret_t rtk_svlan_lookupType_set(rtk_svlan_lookupType_t type)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= SVLAN_LOOKUP_END)
-        return RT_ERR_CHIP_NOT_SUPPORTED;
-
-
-    svlan_lookupType = type;
-
-    retVal = rtl8367c_setAsicSvlanLookupType((rtk_uint32)type);
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtk_svlan_lookupType_get
- * Description:
- *      Get lookup type of SVLAN
- * Input:
- *      pType       - lookup type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- * Note:
- *      none
- */
-rtk_api_ret_t rtk_svlan_lookupType_get(rtk_svlan_lookupType_t *pType)
-{
-    rtk_api_ret_t   retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pType)
-        return RT_ERR_NULL_POINTER;
-
-    retVal = rtl8367c_getAsicSvlanLookupType(pType);
-
-    svlan_lookupType = *pType;
-
-    return retVal;
-}
-
-/* Function Name:
- *      rtk_svlan_trapPri_set
- * Description:
- *      Set svlan trap priority
- * Input:
- *      priority - priority for trap packets
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_QOS_INT_PRIORITY
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_svlan_trapPri_set(rtk_pri_t priority)
-{
-    rtk_api_ret_t   retVal;
-
-    RTK_CHK_INIT_STATE();
-
-    if(priority > RTL8367C_PRIMAX)
-        return RT_ERR_OUT_OF_RANGE;
-
-    retVal = rtl8367c_setAsicSvlanTrapPriority(priority);
-
-    return retVal;
-}   /* end of rtk_svlan_trapPri_set */
-
-/* Function Name:
- *      rtk_svlan_trapPri_get
- * Description:
- *      Get svlan trap priority
- * Input:
- *      None
- * Output:
- *      pPriority - priority for trap packets
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None
- */
-rtk_api_ret_t rtk_svlan_trapPri_get(rtk_pri_t *pPriority)
-{
-    rtk_api_ret_t   retVal;
-
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pPriority)
-        return RT_ERR_NULL_POINTER;
-
-    retVal = rtl8367c_getAsicSvlanTrapPriority(pPriority);
-
-    return retVal;
-}   /* end of rtk_svlan_trapPri_get */
-
-
-/* Function Name:
- *      rtk_svlan_checkAndCreateMbr
- * Description:
- *      Check and create Member configuration and return index
- * Input:
- *      vid  - VLAN id.
- * Output:
- *      pIndex  - Member configuration index
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_VLAN_VID     - Invalid VLAN ID.
- *      RT_ERR_TBL_FULL     - Member Configuration table full
- * Note:
- *
- */
-rtk_api_ret_t rtk_svlan_checkAndCreateMbr(rtk_vlan_t vid, rtk_uint32 *pIndex)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 svidx;
-    rtk_uint32 empty_idx = 0xFFFF;
-    rtl8367c_svlan_memconf_t svlan_cfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* vid must be 0~4095 */
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Null pointer check */
-    if(NULL == pIndex)
-        return RT_ERR_NULL_POINTER;
-
-    /* Search exist entry */
-    for (svidx = 0; svidx <= RTL8367C_SVIDXMAX; svidx++)
-    {
-        if(svlan_mbrCfgUsage[svidx] == TRUE)
-        {
-            if(svlan_mbrCfgVid[svidx] == vid)
-            {
-                /* Found! return index */
-                *pIndex = svidx;
-                return RT_ERR_OK;
-            }
-        }
-        else if(empty_idx == 0xFFFF)
-        {
-            empty_idx = svidx;
-        }
-
-    }
-
-    if(empty_idx == 0xFFFF)
-    {
-        /* No empty index */
-        return RT_ERR_TBL_FULL;
-    }
-
-    svlan_mbrCfgUsage[empty_idx] = TRUE;
-    svlan_mbrCfgVid[empty_idx] = vid;
-
-    memset(&svlan_cfg, 0, sizeof(rtl8367c_svlan_memconf_t));
-
-    svlan_cfg.vs_svid = vid;
-    /*for create check*/
-    if(vid == 0)
-    {
-        svlan_cfg.vs_efid = 1;
-    }
-
-    if((retVal = rtl8367c_setAsicSvlanMemberConfiguration(empty_idx, &svlan_cfg)) != RT_ERR_OK)
-        return retVal;
-
-    *pIndex = empty_idx;
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/trap.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/trap.c
deleted file mode 100644
index af9661058b..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/trap.c
+++ /dev/null
@@ -1,1229 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in Trap module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <trap.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_port.h>
-#include <rtl8367c_asicdrv_igmp.h>
-#include <rtl8367c_asicdrv_rma.h>
-#include <rtl8367c_asicdrv_eav.h>
-#include <rtl8367c_asicdrv_oam.h>
-#include <rtl8367c_asicdrv_svlan.h>
-#include <rtl8367c_asicdrv_unknownMulticast.h>
-#include <rtl8367c_asicdrv_dot1x.h>
-
-/* Function Name:
- *      rtk_trap_unknownUnicastPktAction_set
- * Description:
- *      Set unknown unicast packet action configuration.
- * Input:
- *      port            - ingress port ID for unknown unicast packet
- *      ucast_action    - Unknown unicast action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- *          - UCAST_ACTION_FLOODING
- */
-rtk_api_ret_t rtk_trap_unknownUnicastPktAction_set(rtk_port_t port, rtk_trap_ucast_action_t ucast_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (ucast_action >= UCAST_ACTION_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicPortUnknownDaBehavior(rtk_switch_port_L2P_get(port), ucast_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unknownUnicastPktAction_get
- * Description:
- *      Get unknown unicast packet action configuration.
- * Input:
- *      port            - ingress port ID for unknown unicast packet
- * Output:
- *      pUcast_action   - Unknown unicast action.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- *      RT_ERR_NULL_POINTER        - Null pointer
- * Note:
- *      This API can get unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- *          - UCAST_ACTION_FLOODING
- */
-rtk_api_ret_t rtk_trap_unknownUnicastPktAction_get(rtk_port_t port, rtk_trap_ucast_action_t *pUcast_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (NULL == pUcast_action)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortUnknownDaBehavior(rtk_switch_port_L2P_get(port), pUcast_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unknownMacPktAction_set
- * Description:
- *      Set unknown source MAC packet action configuration.
- * Input:
- *      ucast_action    - Unknown source MAC action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- */
-rtk_api_ret_t rtk_trap_unknownMacPktAction_set(rtk_trap_ucast_action_t ucast_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (ucast_action >= UCAST_ACTION_FLOODING)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicPortUnknownSaBehavior(ucast_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unknownMacPktAction_get
- * Description:
- *      Get unknown source MAC packet action configuration.
- * Input:
- *      None.
- * Output:
- *      pUcast_action   - Unknown source MAC action.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NULL_POINTER        - Null Pointer.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *
- */
-rtk_api_ret_t rtk_trap_unknownMacPktAction_get(rtk_trap_ucast_action_t *pUcast_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pUcast_action)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortUnknownSaBehavior(pUcast_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unmatchMacPktAction_set
- * Description:
- *      Set unmatch source MAC packet action configuration.
- * Input:
- *      ucast_action    - Unknown source MAC action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- */
-rtk_api_ret_t rtk_trap_unmatchMacPktAction_set(rtk_trap_ucast_action_t ucast_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (ucast_action >= UCAST_ACTION_FLOODING)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicPortUnmatchedSaBehavior(ucast_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unmatchMacPktAction_get
- * Description:
- *      Get unmatch source MAC packet action configuration.
- * Input:
- *      None.
- * Output:
- *      pUcast_action   - Unknown source MAC action.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- *      This API can set unknown unicast packet action configuration.
- *      The unknown unicast action is as following:
- *          - UCAST_ACTION_FORWARD_PMASK
- *          - UCAST_ACTION_DROP
- *          - UCAST_ACTION_TRAP2CPU
- */
-rtk_api_ret_t rtk_trap_unmatchMacPktAction_get(rtk_trap_ucast_action_t *pUcast_action)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pUcast_action)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortUnmatchedSaBehavior(pUcast_action)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unmatchMacMoving_set
- * Description:
- *      Set unmatch source MAC packet moving state.
- * Input:
- *      port        - Port ID.
- *      enable      - ENABLED: allow SA moving, DISABLE: don't allow SA moving.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- */
-rtk_api_ret_t rtk_trap_unmatchMacMoving_set(rtk_port_t port, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicPortUnmatchedSaMoving(rtk_switch_port_L2P_get(port), enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unmatchMacMoving_get
- * Description:
- *      Set unmatch source MAC packet moving state.
- * Input:
- *      port        - Port ID.
- * Output:
- *      pEnable     - ENABLED: allow SA moving, DISABLE: don't allow SA moving.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT               - Invalid input parameters.
- * Note:
- */
-rtk_api_ret_t rtk_trap_unmatchMacMoving_get(rtk_port_t port, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* check port valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortUnmatchedSaMoving(rtk_switch_port_L2P_get(port), pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unknownMcastPktAction_set
- * Description:
- *      Set behavior of unknown multicast
- * Input:
- *      port            - Port id.
- *      type            - unknown multicast packet type.
- *      mcast_action    - unknown multicast action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID         - Invalid port number.
- *      RT_ERR_NOT_ALLOWED     - Invalid action.
- *      RT_ERR_INPUT         - Invalid input parameters.
- * Note:
- *      When receives an unknown multicast packet, switch may trap, drop or flood this packet
- *      (1) The unknown multicast packet type is as following:
- *          - MCAST_L2
- *          - MCAST_IPV4
- *          - MCAST_IPV6
- *      (2) The unknown multicast action is as following:
- *          - MCAST_ACTION_FORWARD
- *          - MCAST_ACTION_DROP
- *          - MCAST_ACTION_TRAP2CPU
- */
-rtk_api_ret_t rtk_trap_unknownMcastPktAction_set(rtk_port_t port, rtk_mcast_type_t type, rtk_trap_mcast_action_t mcast_action)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 rawAction;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (type >= MCAST_END)
-        return RT_ERR_INPUT;
-
-    if (mcast_action >= MCAST_ACTION_END)
-        return RT_ERR_INPUT;
-
-
-    switch (type)
-    {
-        case MCAST_L2:
-            if (MCAST_ACTION_ROUTER_PORT == mcast_action)
-                return RT_ERR_INPUT;
-            else if(MCAST_ACTION_DROP_EX_RMA == mcast_action)
-                rawAction = L2_UNKOWN_MULTICAST_DROP_EXCLUDE_RMA;
-            else
-                rawAction = (rtk_uint32)mcast_action;
-
-            if ((retVal = rtl8367c_setAsicUnknownL2MulticastBehavior(rtk_switch_port_L2P_get(port), rawAction)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case MCAST_IPV4:
-            if (MCAST_ACTION_DROP_EX_RMA == mcast_action)
-                return RT_ERR_INPUT;
-            else
-                rawAction = (rtk_uint32)mcast_action;
-
-            if ((retVal = rtl8367c_setAsicUnknownIPv4MulticastBehavior(rtk_switch_port_L2P_get(port), rawAction)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case MCAST_IPV6:
-            if (MCAST_ACTION_DROP_EX_RMA == mcast_action)
-                return RT_ERR_INPUT;
-            else
-                rawAction = (rtk_uint32)mcast_action;
-
-            if ((retVal = rtl8367c_setAsicUnknownIPv6MulticastBehavior(rtk_switch_port_L2P_get(port), rawAction)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_unknownMcastPktAction_get
- * Description:
- *      Get behavior of unknown multicast
- * Input:
- *      type - unknown multicast packet type.
- * Output:
- *      pMcast_action - unknown multicast action.
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_PORT_ID             - Invalid port number.
- *      RT_ERR_NOT_ALLOWED         - Invalid operation.
- *      RT_ERR_INPUT             - Invalid input parameters.
- * Note:
- *      When receives an unknown multicast packet, switch may trap, drop or flood this packet
- *      (1) The unknown multicast packet type is as following:
- *          - MCAST_L2
- *          - MCAST_IPV4
- *          - MCAST_IPV6
- *      (2) The unknown multicast action is as following:
- *          - MCAST_ACTION_FORWARD
- *          - MCAST_ACTION_DROP
- *          - MCAST_ACTION_TRAP2CPU
- */
-rtk_api_ret_t rtk_trap_unknownMcastPktAction_get(rtk_port_t port, rtk_mcast_type_t type, rtk_trap_mcast_action_t *pMcast_action)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 rawAction;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (type >= MCAST_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pMcast_action)
-        return RT_ERR_NULL_POINTER;
-
-    switch (type)
-    {
-        case MCAST_L2:
-            if ((retVal = rtl8367c_getAsicUnknownL2MulticastBehavior(rtk_switch_port_L2P_get(port), &rawAction)) != RT_ERR_OK)
-                return retVal;
-
-            if(L2_UNKOWN_MULTICAST_DROP_EXCLUDE_RMA == rawAction)
-                *pMcast_action = MCAST_ACTION_DROP_EX_RMA;
-            else
-                *pMcast_action = (rtk_trap_mcast_action_t)rawAction;
-
-            break;
-        case MCAST_IPV4:
-            if ((retVal = rtl8367c_getAsicUnknownIPv4MulticastBehavior(rtk_switch_port_L2P_get(port), &rawAction)) != RT_ERR_OK)
-                return retVal;
-
-            *pMcast_action = (rtk_trap_mcast_action_t)rawAction;
-            break;
-        case MCAST_IPV6:
-            if ((retVal = rtl8367c_getAsicUnknownIPv6MulticastBehavior(rtk_switch_port_L2P_get(port), &rawAction)) != RT_ERR_OK)
-                return retVal;
-
-            *pMcast_action = (rtk_trap_mcast_action_t)rawAction;
-            break;
-        default:
-            break;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_lldpEnable_set
- * Description:
- *      Set LLDP enable.
- * Input:
- *      enabled - LLDP enable, 0: follow RMA, 1: use LLDP action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                  - OK
- *      RT_ERR_FAILED              - Failed
- *      RT_ERR_SMI                 - SMI access error
- *      RT_ERR_NOT_ALLOWED         - Invalid action.
- *      RT_ERR_INPUT             - Invalid input parameters.
- * Note:
- *      - DMAC                                                 Assignment
- *      - 01:80:c2:00:00:0e ethertype = 0x88CC    LLDP
- *      - 01:80:c2:00:00:03 ethertype = 0x88CC
- *      - 01:80:c2:00:00:00 ethertype = 0x88CC
-
- */
-rtk_api_ret_t rtk_trap_lldpEnable_set(rtk_enable_t enabled)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-    rtk_enable_t tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (enabled >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_getAsicRmaLldp(&tmp, &rmacfg)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicRmaLldp(enabled, &rmacfg)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_lldpEnable_get
- * Description:
- *      Get LLDP status.
- * Input:
- *      None
- * Output:
- *      pEnabled - LLDP enable, 0: follow RMA, 1: use LLDP action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT         - Invalid input parameters.
- * Note:
- *      LLDP is as following definition.
- *      - DMAC                                                 Assignment
- *      - 01:80:c2:00:00:0e ethertype = 0x88CC    LLDP
- *      - 01:80:c2:00:00:03 ethertype = 0x88CC
- *      - 01:80:c2:00:00:00 ethertype = 0x88CC
- */
-rtk_api_ret_t rtk_trap_lldpEnable_get(rtk_enable_t *pEnabled)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicRmaLldp(pEnabled, &rmacfg)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_reasonTrapToCpuPriority_set
- * Description:
- *      Set priority value of a packet that trapped to CPU port according to specific reason.
- * Input:
- *      type     - reason that trap to CPU port.
- *      priority - internal priority that is going to be set for specific trap reason.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT - The module is not initial
- *      RT_ERR_INPUT    - Invalid input parameter
- * Note:
- *      Currently the trap reason that supported are listed as follows:
- *      - TRAP_REASON_RMA
- *      - TRAP_REASON_OAM
- *      - TRAP_REASON_1XUNAUTH
- *      - TRAP_REASON_VLANSTACK
- *      - TRAP_REASON_UNKNOWNMC
- */
-rtk_api_ret_t rtk_trap_reasonTrapToCpuPriority_set(rtk_trap_reason_type_t type, rtk_pri_t priority)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= TRAP_REASON_END)
-        return RT_ERR_INPUT;
-
-    if (priority > RTL8367C_PRIMAX)
-        return  RT_ERR_QOS_INT_PRIORITY;
-
-    switch (type)
-    {
-        case TRAP_REASON_RMA:
-            if ((retVal = rtl8367c_getAsicRma(0, &rmacfg)) != RT_ERR_OK)
-                return retVal;
-            rmacfg.trap_priority= priority;
-            if ((retVal = rtl8367c_setAsicRma(0, &rmacfg)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case TRAP_REASON_OAM:
-            if ((retVal = rtl8367c_setAsicOamCpuPri(priority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case TRAP_REASON_1XUNAUTH:
-            if ((retVal = rtl8367c_setAsic1xTrapPriority(priority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case TRAP_REASON_VLANSTACK:
-            if ((retVal = rtl8367c_setAsicSvlanTrapPriority(priority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case TRAP_REASON_UNKNOWNMC:
-            if ((retVal = rtl8367c_setAsicUnknownMulticastTrapPriority(priority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        default:
-            return RT_ERR_CHIP_NOT_SUPPORTED;
-    }
-
-
-    return RT_ERR_OK;
-}
-
-
-/* Function Name:
- *      rtk_trap_reasonTrapToCpuPriority_get
- * Description:
- *      Get priority value of a packet that trapped to CPU port according to specific reason.
- * Input:
- *      type      - reason that trap to CPU port.
- * Output:
- *      pPriority - configured internal priority for such reason.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NOT_INIT     - The module is not initial
- *      RT_ERR_INPUT        - Invalid input parameter
- *      RT_ERR_NULL_POINTER - NULL pointer
- * Note:
- *      Currently the trap reason that supported are listed as follows:
- *      - TRAP_REASON_RMA
- *      - TRAP_REASON_OAM
- *      - TRAP_REASON_1XUNAUTH
- *      - TRAP_REASON_VLANSTACK
- *      - TRAP_REASON_UNKNOWNMC
- */
-rtk_api_ret_t rtk_trap_reasonTrapToCpuPriority_get(rtk_trap_reason_type_t type, rtk_pri_t *pPriority)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= TRAP_REASON_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pPriority)
-        return RT_ERR_NULL_POINTER;
-
-    switch (type)
-    {
-        case TRAP_REASON_RMA:
-            if ((retVal = rtl8367c_getAsicRma(0, &rmacfg)) != RT_ERR_OK)
-                return retVal;
-            *pPriority = rmacfg.trap_priority;
-
-            break;
-        case TRAP_REASON_OAM:
-            if ((retVal = rtl8367c_getAsicOamCpuPri(pPriority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case TRAP_REASON_1XUNAUTH:
-            if ((retVal = rtl8367c_getAsic1xTrapPriority(pPriority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case TRAP_REASON_VLANSTACK:
-            if ((retVal = rtl8367c_getAsicSvlanTrapPriority(pPriority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        case TRAP_REASON_UNKNOWNMC:
-            if ((retVal = rtl8367c_getAsicUnknownMulticastTrapPriority(pPriority)) != RT_ERR_OK)
-                return retVal;
-
-            break;
-        default:
-            return RT_ERR_CHIP_NOT_SUPPORTED;
-
-    }
-
-    return RT_ERR_OK;
-}
-
-
-
-/* Function Name:
- *      rtk_trap_rmaAction_set
- * Description:
- *      Set Reserved multicast address action configuration.
- * Input:
- *      type    - rma type.
- *      rma_action - RMA action.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      (1)They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- *      (2) The RMA action is as following:
- *      - RMA_ACTION_FORWARD
- *      - RMA_ACTION_TRAP2CPU
- *      - RMA_ACTION_DROP
- *      - RMA_ACTION_FORWARD_EXCLUDE_CPU
- */
-rtk_api_ret_t rtk_trap_rmaAction_set(rtk_trap_type_t type, rtk_trap_rma_action_t rma_action)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= TRAP_END)
-        return RT_ERR_INPUT;
-
-    if (rma_action >= RMA_ACTION_END)
-        return RT_ERR_RMA_ACTION;
-
-    if (type >= 0 && type <= TRAP_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.operation = rma_action;
-
-        if ((retVal = rtl8367c_setAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type == TRAP_CDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.operation = rma_action;
-
-        if ((retVal = rtl8367c_setAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type  == TRAP_CSSTP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.operation = rma_action;
-
-        if ((retVal = rtl8367c_setAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type  == TRAP_LLDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.operation = rma_action;
-
-        if ((retVal = rtl8367c_setAsicRmaLldp(tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_rmaAction_get
- * Description:
- *      Get Reserved multicast address action configuration.
- * Input:
- *      type - rma type.
- * Output:
- *      pRma_action - RMA action.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      (1)They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- *      (2) The RMA action is as following:
- *      - RMA_ACTION_FORWARD
- *      - RMA_ACTION_TRAP2CPU
- *      - RMA_ACTION_DROP
- *      - RMA_ACTION_FORWARD_EXCLUDE_CPU
- */
-rtk_api_ret_t rtk_trap_rmaAction_get(rtk_trap_type_t type, rtk_trap_rma_action_t *pRma_action)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= TRAP_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pRma_action)
-        return RT_ERR_NULL_POINTER;
-
-    if (type >= 0 && type <= TRAP_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pRma_action = rmacfg.operation;
-    }
-    else if (type == TRAP_CDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pRma_action = rmacfg.operation;
-    }
-    else if (type == TRAP_CSSTP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pRma_action = rmacfg.operation;
-    }
-    else if (type == TRAP_LLDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp,&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pRma_action = rmacfg.operation;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_rmaKeepFormat_set
- * Description:
- *      Set Reserved multicast address keep format configuration.
- * Input:
- *      type    - rma type.
- *      enable - enable keep format.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_ENABLE       - Invalid IFG parameter
- * Note:
- *
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- */
-rtk_api_ret_t rtk_trap_rmaKeepFormat_set(rtk_trap_type_t type, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= TRAP_END)
-        return RT_ERR_INPUT;
-
-    if (enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if (type >= 0 && type <= TRAP_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.keep_format = enable;
-
-        if ((retVal = rtl8367c_setAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type == TRAP_CDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.keep_format = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type  == TRAP_CSSTP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.keep_format = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else if (type  == TRAP_LLDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        rmacfg.keep_format = enable;
-
-        if ((retVal = rtl8367c_setAsicRmaLldp(tmp, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trap_rmaKeepFormat_get
- * Description:
- *      Get Reserved multicast address action configuration.
- * Input:
- *      type - rma type.
- * Output:
- *      pEnable - keep format status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- * Note:
- *      There are 48 types of Reserved Multicast Address frame for application usage.
- *      They are as following definition.
- *      - TRAP_BRG_GROUP,
- *      - TRAP_FD_PAUSE,
- *      - TRAP_SP_MCAST,
- *      - TRAP_1X_PAE,
- *      - TRAP_UNDEF_BRG_04,
- *      - TRAP_UNDEF_BRG_05,
- *      - TRAP_UNDEF_BRG_06,
- *      - TRAP_UNDEF_BRG_07,
- *      - TRAP_PROVIDER_BRIDGE_GROUP_ADDRESS,
- *      - TRAP_UNDEF_BRG_09,
- *      - TRAP_UNDEF_BRG_0A,
- *      - TRAP_UNDEF_BRG_0B,
- *      - TRAP_UNDEF_BRG_0C,
- *      - TRAP_PROVIDER_BRIDGE_GVRP_ADDRESS,
- *      - TRAP_8021AB,
- *      - TRAP_UNDEF_BRG_0F,
- *      - TRAP_BRG_MNGEMENT,
- *      - TRAP_UNDEFINED_11,
- *      - TRAP_UNDEFINED_12,
- *      - TRAP_UNDEFINED_13,
- *      - TRAP_UNDEFINED_14,
- *      - TRAP_UNDEFINED_15,
- *      - TRAP_UNDEFINED_16,
- *      - TRAP_UNDEFINED_17,
- *      - TRAP_UNDEFINED_18,
- *      - TRAP_UNDEFINED_19,
- *      - TRAP_UNDEFINED_1A,
- *      - TRAP_UNDEFINED_1B,
- *      - TRAP_UNDEFINED_1C,
- *      - TRAP_UNDEFINED_1D,
- *      - TRAP_UNDEFINED_1E,
- *      - TRAP_UNDEFINED_1F,
- *      - TRAP_GMRP,
- *      - TRAP_GVRP,
- *      - TRAP_UNDEF_GARP_22,
- *      - TRAP_UNDEF_GARP_23,
- *      - TRAP_UNDEF_GARP_24,
- *      - TRAP_UNDEF_GARP_25,
- *      - TRAP_UNDEF_GARP_26,
- *      - TRAP_UNDEF_GARP_27,
- *      - TRAP_UNDEF_GARP_28,
- *      - TRAP_UNDEF_GARP_29,
- *      - TRAP_UNDEF_GARP_2A,
- *      - TRAP_UNDEF_GARP_2B,
- *      - TRAP_UNDEF_GARP_2C,
- *      - TRAP_UNDEF_GARP_2D,
- *      - TRAP_UNDEF_GARP_2E,
- *      - TRAP_UNDEF_GARP_2F,
- *      - TRAP_CDP.
- *      - TRAP_CSSTP.
- *      - TRAP_LLDP.
- */
-rtk_api_ret_t rtk_trap_rmaKeepFormat_get(rtk_trap_type_t type, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_rma_t rmacfg;
-    rtk_uint32 tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (type >= TRAP_END)
-        return RT_ERR_INPUT;
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if (type >= 0 && type <= TRAP_UNDEF_GARP_2F)
-    {
-        if ((retVal = rtl8367c_getAsicRma(type, &rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.keep_format;
-    }
-    else if (type == TRAP_CDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCdp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.keep_format;
-    }
-    else if (type == TRAP_CSSTP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaCsstp(&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.keep_format;
-    }
-    else if (type == TRAP_LLDP)
-    {
-        if ((retVal = rtl8367c_getAsicRmaLldp(&tmp,&rmacfg)) != RT_ERR_OK)
-            return retVal;
-
-        *pEnable = rmacfg.keep_format;
-    }
-    else
-        return RT_ERR_INPUT;
-
-    return RT_ERR_OK;
-}
-
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/trunk.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/trunk.c
deleted file mode 100644
index 8a88dc5ff0..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/trunk.c
+++ /dev/null
@@ -1,605 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in Trunk module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <trunk.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_trunking.h>
-
-/* Function Name:
- *      rtk_trunk_port_set
- * Description:
- *      Set trunking group available port mask
- * Input:
- *      trk_gid                 - trunk group id
- *      pTrunk_member_portmask  - Logic trunking member port mask
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      The API can set port trunking group port mask. Each port trunking group has max 4 ports.
- *      If enabled port mask has less than 2 ports available setting, then this trunking group function is disabled.
- */
-rtk_api_ret_t rtk_trunk_port_set(rtk_trunk_group_t trk_gid, rtk_portmask_t *pTrunk_member_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-    rtk_uint32 regValue, type, tmp;
-
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0249)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_getAsicReg(0x1300, &regValue)) != RT_ERR_OK)
-        return retVal;
-
-    if((retVal = rtl8367c_setAsicReg(0x13C2, 0x0000)) != RT_ERR_OK)
-        return retVal;
-
-    switch (regValue)
-    {
-        case 0x0276:
-        case 0x0597:
-        case 0x6367:
-            type = 0;
-            break;
-        case 0x0652:
-        case 0x6368:
-            type = 1;
-            break;
-        case 0x0801:
-        case 0x6511:
-            type = 2;
-            break;
-        default:
-            return RT_ERR_FAILED;
-    }
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Trunk Group Valid */
-    RTK_CHK_TRUNK_GROUP_VALID(trk_gid);
-
-    if(NULL == pTrunk_member_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    RTK_CHK_PORTMASK_VALID(pTrunk_member_portmask);
-
-    if((retVal = rtk_switch_portmask_L2P_get(pTrunk_member_portmask, &pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    if((type == 0) || (type == 1))
-    {
-        if ((pmsk | RTL8367C_PORT_TRUNK_GROUP_MASK_MASK(trk_gid)) != (rtk_uint32)RTL8367C_PORT_TRUNK_GROUP_MASK_MASK(trk_gid))
-            return RT_ERR_PORT_MASK;
-
-        pmsk = (pmsk & RTL8367C_PORT_TRUNK_GROUP_MASK_MASK(trk_gid)) >> RTL8367C_PORT_TRUNK_GROUP_MASK_OFFSET(trk_gid);
-    }
-    else if(type == 2)
-    {
-        tmp = 0;
-
-        if(pmsk & 0x2)
-            tmp |= 1;
-        if(pmsk & 0x8)
-            tmp |=2;
-        if(pmsk & 0x80)
-            tmp |=8;
-
-        pmsk = tmp;
-    }
-
-    if ((retVal = rtl8367c_setAsicTrunkingGroup(trk_gid, pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_port_get
- * Description:
- *      Get trunking group available port mask
- * Input:
- *      trk_gid - trunk group id
- * Output:
- *      pTrunk_member_portmask - Logic trunking member port mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- * Note:
- *      The API can get 2 port trunking group.
- */
-rtk_api_ret_t rtk_trunk_port_get(rtk_trunk_group_t trk_gid, rtk_portmask_t *pTrunk_member_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmsk;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Trunk Group Valid */
-    RTK_CHK_TRUNK_GROUP_VALID(trk_gid);
-
-    if ((retVal = rtl8367c_getAsicTrunkingGroup(trk_gid, &pmsk)) != RT_ERR_OK)
-        return retVal;
-
-    pmsk = pmsk << RTL8367C_PORT_TRUNK_GROUP_MASK_OFFSET(trk_gid);
-
-    if((retVal = rtk_switch_portmask_P2L_get(pmsk, pTrunk_member_portmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_distributionAlgorithm_set
- * Description:
- *      Set port trunking hash select sources
- * Input:
- *      trk_gid         - trunk group id
- *      algo_bitmask   - Bitmask of the distribution algorithm
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- *      RT_ERR_LA_HASHMASK  - Hash algorithm selection error.
- *      RT_ERR_PORT_MASK    - Invalid portmask.
- * Note:
- *      The API can set port trunking hash algorithm sources.
- *      7 bits mask for link aggregation group0 hash parameter selection {DIP, SIP, DMAC, SMAC, SPA}
- *      - 0b0000001: SPA
- *      - 0b0000010: SMAC
- *      - 0b0000100: DMAC
- *      - 0b0001000: SIP
- *      - 0b0010000: DIP
- *      - 0b0100000: TCP/UDP Source Port
- *      - 0b1000000: TCP/UDP Destination Port
- *      Example:
- *      - 0b0000011: SMAC & SPA
- *      - Note that it could be an arbitrary combination or independent set
- */
-rtk_api_ret_t rtk_trunk_distributionAlgorithm_set(rtk_trunk_group_t trk_gid, rtk_uint32 algo_bitmask)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (trk_gid != RTK_WHOLE_SYSTEM)
-        return RT_ERR_LA_TRUNK_ID;
-
-    if (algo_bitmask >= 128)
-        return RT_ERR_LA_HASHMASK;
-
-    if ((retVal = rtl8367c_setAsicTrunkingHashSelect(algo_bitmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_distributionAlgorithm_get
- * Description:
- *      Get port trunking hash select sources
- * Input:
- *      trk_gid - trunk group id
- * Output:
- *      pAlgo_bitmask -  Bitmask of the distribution algorithm
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_LA_TRUNK_ID  - Invalid trunking group
- * Note:
- *      The API can get port trunking hash algorithm sources.
- */
-rtk_api_ret_t rtk_trunk_distributionAlgorithm_get(rtk_trunk_group_t trk_gid, rtk_uint32 *pAlgo_bitmask)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (trk_gid != RTK_WHOLE_SYSTEM)
-        return RT_ERR_LA_TRUNK_ID;
-
-    if(NULL == pAlgo_bitmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicTrunkingHashSelect((rtk_uint32 *)pAlgo_bitmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_trafficSeparate_set
- * Description:
- *      Set the traffic separation setting of a trunk group from the specified device.
- * Input:
- *      trk_gid      - trunk group id
- *      separateType     - traffic separation setting
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID     - invalid unit id
- *      RT_ERR_LA_TRUNK_ID - invalid trunk ID
- *      RT_ERR_LA_HASHMASK - invalid hash mask
- * Note:
- *      SEPARATE_NONE: disable traffic separation
- *      SEPARATE_FLOOD: trunk MSB link up port is dedicated to TX flooding (L2 lookup miss) traffic
- */
-rtk_api_ret_t rtk_trunk_trafficSeparate_set(rtk_trunk_group_t trk_gid, rtk_trunk_separateType_t separateType)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 enabled;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (trk_gid != RTK_WHOLE_SYSTEM)
-        return RT_ERR_LA_TRUNK_ID;
-
-    if(separateType >= SEPARATE_END)
-        return RT_ERR_INPUT;
-
-    enabled = (separateType == SEPARATE_FLOOD) ? ENABLED : DISABLED;
-    if ((retVal = rtl8367c_setAsicTrunkingFlood(enabled)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_trafficSeparate_get
- * Description:
- *      Get the traffic separation setting of a trunk group from the specified device.
- * Input:
- *      trk_gid        - trunk group id
- * Output:
- *      pSeparateType   - pointer separated traffic type
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_LA_TRUNK_ID  - invalid trunk ID
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      SEPARATE_NONE: disable traffic separation
- *      SEPARATE_FLOOD: trunk MSB link up port is dedicated to TX flooding (L2 lookup miss) traffic
- */
-rtk_api_ret_t rtk_trunk_trafficSeparate_get(rtk_trunk_group_t trk_gid, rtk_trunk_separateType_t *pSeparateType)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 enabled;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if (trk_gid != RTK_WHOLE_SYSTEM)
-        return RT_ERR_LA_TRUNK_ID;
-
-    if(NULL == pSeparateType)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicTrunkingFlood(&enabled)) != RT_ERR_OK)
-        return retVal;
-
-    *pSeparateType = (enabled == ENABLED) ? SEPARATE_FLOOD : SEPARATE_NONE;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_mode_set
- * Description:
- *      Set the trunk mode to the specified device.
- * Input:
- *      mode - trunk mode
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_INPUT   - invalid input parameter
- * Note:
- *      The enum of the trunk mode as following
- *      - TRUNK_MODE_NORMAL
- *      - TRUNK_MODE_DUMB
- */
-rtk_api_ret_t rtk_trunk_mode_set(rtk_trunk_mode_t mode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(mode >= TRUNK_MODE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicTrunkingMode((rtk_uint32)mode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_mode_get
- * Description:
- *      Get the trunk mode from the specified device.
- * Input:
- *      None
- * Output:
- *      pMode - pointer buffer of trunk mode
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      The enum of the trunk mode as following
- *      - TRUNK_MODE_NORMAL
- *      - TRUNK_MODE_DUMB
- */
-rtk_api_ret_t rtk_trunk_mode_get(rtk_trunk_mode_t *pMode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pMode)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicTrunkingMode((rtk_uint32 *)pMode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_trafficPause_set
- * Description:
- *      Set the traffic pause setting of a trunk group.
- * Input:
- *      trk_gid      - trunk group id
- *      enable       - traffic pause state
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_LA_TRUNK_ID - invalid trunk ID
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_trunk_trafficPause_set(rtk_trunk_group_t trk_gid, rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Trunk Group Valid */
-    RTK_CHK_TRUNK_GROUP_VALID(trk_gid);
-
-    if(enable >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setAsicTrunkingFc((rtk_uint32)trk_gid, (rtk_uint32)enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_trafficPause_get
- * Description:
- *      Get the traffic pause setting of a trunk group.
- * Input:
- *      trk_gid        - trunk group id
- * Output:
- *      pEnable        - pointer of traffic pause state.
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_LA_TRUNK_ID  - invalid trunk ID
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_trunk_trafficPause_get(rtk_trunk_group_t trk_gid, rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Trunk Group Valid */
-    RTK_CHK_TRUNK_GROUP_VALID(trk_gid);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicTrunkingFc((rtk_uint32)trk_gid, (rtk_uint32 *)pEnable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_hashMappingTable_set
- * Description:
- *      Set hash value to port array in the trunk group id from the specified device.
- * Input:
- *      trk_gid          - trunk group id
- *      pHash2Port_array - ports associate with the hash value
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID            - invalid unit id
- *      RT_ERR_LA_TRUNK_ID        - invalid trunk ID
- *      RT_ERR_NULL_POINTER       - input parameter may be null pointer
- *      RT_ERR_LA_TRUNK_NOT_EXIST - the trunk doesn't exist
- *      RT_ERR_LA_NOT_MEMBER_PORT - the port is not a member port of the trunk
- *      RT_ERR_LA_CPUPORT         - CPU port can not be aggregated port
- * Note:
- *      Trunk group 0 & 1 shares the same hash mapping table.
- *      Trunk group 2 uses a independent table.
- */
-rtk_api_ret_t rtk_trunk_hashMappingTable_set(rtk_trunk_group_t trk_gid, rtk_trunk_hashVal2Port_t *pHash2Port_array)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 hashValue;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Trunk Group Valid */
-    RTK_CHK_TRUNK_GROUP_VALID(trk_gid);
-
-    if(NULL == pHash2Port_array)
-        return RT_ERR_NULL_POINTER;
-
-    if(trk_gid <= TRUNK_GROUP1)
-    {
-        for(hashValue = 0; hashValue < RTK_MAX_NUM_OF_TRUNK_HASH_VAL; hashValue++)
-        {
-            if ((retVal = rtl8367c_setAsicTrunkingHashTable(hashValue, pHash2Port_array->value[hashValue])) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-    else
-    {
-        for(hashValue = 0; hashValue < RTK_MAX_NUM_OF_TRUNK_HASH_VAL; hashValue++)
-        {
-            if ((retVal = rtl8367c_setAsicTrunkingHashTable1(hashValue, pHash2Port_array->value[hashValue])) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_hashMappingTable_get
- * Description:
- *      Get hash value to port array in the trunk group id from the specified device.
- * Input:
- *      trk_gid          - trunk group id
- * Output:
- *      pHash2Port_array - pointer buffer of ports associate with the hash value
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_UNIT_ID      - invalid unit id
- *      RT_ERR_LA_TRUNK_ID  - invalid trunk ID
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      Trunk group 0 & 1 shares the same hash mapping table.
- *      Trunk group 2 uses a independent table.
- */
-rtk_api_ret_t rtk_trunk_hashMappingTable_get(rtk_trunk_group_t trk_gid, rtk_trunk_hashVal2Port_t *pHash2Port_array)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 hashValue;
-    rtk_uint32 hashPort;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Trunk Group Valid */
-    RTK_CHK_TRUNK_GROUP_VALID(trk_gid);
-
-    if(NULL == pHash2Port_array)
-        return RT_ERR_NULL_POINTER;
-
-    if(trk_gid <= TRUNK_GROUP1)
-    {
-        for(hashValue = 0; hashValue < RTK_MAX_NUM_OF_TRUNK_HASH_VAL; hashValue++)
-        {
-            if ((retVal = rtl8367c_getAsicTrunkingHashTable(hashValue, &hashPort)) != RT_ERR_OK)
-                return retVal;
-
-            pHash2Port_array->value[hashValue] = hashPort;
-        }
-    }
-    else
-    {
-        for(hashValue = 0; hashValue < RTK_MAX_NUM_OF_TRUNK_HASH_VAL; hashValue++)
-        {
-            if ((retVal = rtl8367c_getAsicTrunkingHashTable1(hashValue, &hashPort)) != RT_ERR_OK)
-                return retVal;
-
-            pHash2Port_array->value[hashValue] = hashPort;
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_trunk_portQueueEmpty_get
- * Description:
- *      Get the port mask which all queues are empty.
- * Input:
- *      None.
- * Output:
- *      pEmpty_portmask   - pointer empty port mask
- * Return:
- *      RT_ERR_OK
- *      RT_ERR_FAILED
- *      RT_ERR_NULL_POINTER - input parameter may be null pointer
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_trunk_portQueueEmpty_get(rtk_portmask_t *pEmpty_portmask)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 pmask;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEmpty_portmask)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicQeueuEmptyStatus(&pmask)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtk_switch_portmask_P2L_get(pmask, pEmpty_portmask)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/vlan.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/vlan.c
deleted file mode 100644
index f7480c4906..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/vlan.c
+++ /dev/null
@@ -1,2124 +0,0 @@
-/*
- * Copyright (C) 2013 Realtek Semiconductor Corp.
- * All Rights Reserved.
- *
- * Unless you and Realtek execute a separate written software license
- * agreement governing use of this software, this software is licensed
- * to you under the terms of the GNU General Public License version 2,
- * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
- *
- * $Revision: 76306 $
- * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
- *
- * Purpose : RTK switch high-level API for RTL8367/RTL8367C
- * Feature : Here is a list of all functions and variables in VLAN module.
- *
- */
-
-#include <rtk_switch.h>
-#include <rtk_error.h>
-#include <vlan.h>
-#include <rate.h>
-#include <string.h>
-
-#include <rtl8367c_asicdrv.h>
-#include <rtl8367c_asicdrv_vlan.h>
-#include <rtl8367c_asicdrv_dot1x.h>
-
-typedef enum vlan_mbrCfgType_e
-{
-    MBRCFG_UNUSED = 0,
-    MBRCFG_USED_BY_VLAN,
-    MBRCFG_END
-}vlan_mbrCfgType_t;
-
-static rtk_vlan_t           vlan_mbrCfgVid[RTL8367C_CVIDXNO];
-static vlan_mbrCfgType_t    vlan_mbrCfgUsage[RTL8367C_CVIDXNO];
-
-/* Function Name:
- *      rtk_vlan_init
- * Description:
- *      Initialize VLAN.
- * Input:
- *      None
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- * Note:
- *      VLAN is disabled by default. User has to call this API to enable VLAN before
- *      using it. And It will set a default VLAN(vid 1) including all ports and set
- *      all ports PVID to the default VLAN.
- */
-rtk_api_ret_t rtk_vlan_init(void)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtl8367c_user_vlan4kentry vlan4K;
-    rtl8367c_vlanconfiguser vlanMC;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Clean Database */
-    memset(vlan_mbrCfgVid, 0x00, sizeof(rtk_vlan_t) * RTL8367C_CVIDXNO);
-    memset(vlan_mbrCfgUsage, 0x00, sizeof(vlan_mbrCfgType_t) * RTL8367C_CVIDXNO);
-
-    /* clean 32 VLAN member configuration */
-    for (i = 0; i <= RTL8367C_CVIDXMAX; i++)
-    {
-        vlanMC.evid = 0;
-        vlanMC.mbr = 0;
-        vlanMC.fid_msti = 0;
-        vlanMC.envlanpol = 0;
-        vlanMC.meteridx = 0;
-        vlanMC.vbpen = 0;
-        vlanMC.vbpri = 0;
-        if ((retVal = rtl8367c_setAsicVlanMemberConfig(i, &vlanMC)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /* Set a default VLAN with vid 1 to 4K table for all ports */
-    memset(&vlan4K, 0, sizeof(rtl8367c_user_vlan4kentry));
-    vlan4K.vid = 1;
-    vlan4K.mbr = RTK_PHY_PORTMASK_ALL;
-    vlan4K.untag = RTK_PHY_PORTMASK_ALL;
-    vlan4K.fid_msti = 0;
-    if ((retVal = rtl8367c_setAsicVlan4kEntry(&vlan4K)) != RT_ERR_OK)
-        return retVal;
-
-    /* Also set the default VLAN to 32 member configuration index 0 */
-    memset(&vlanMC, 0, sizeof(rtl8367c_vlanconfiguser));
-    vlanMC.evid = 1;
-    vlanMC.mbr = RTK_PHY_PORTMASK_ALL;
-    vlanMC.fid_msti = 0;
-    if ((retVal = rtl8367c_setAsicVlanMemberConfig(0, &vlanMC)) != RT_ERR_OK)
-            return retVal;
-
-    /* Set all ports PVID to default VLAN and tag-mode to original */
-    RTK_SCAN_ALL_PHY_PORTMASK(i)
-    {
-        if ((retVal = rtl8367c_setAsicVlanPortBasedVID(i, 0, 0)) != RT_ERR_OK)
-            return retVal;
-        if ((retVal = rtl8367c_setAsicVlanEgressTagMode(i, EG_TAG_MODE_ORI)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /* Updata Databse */
-    vlan_mbrCfgUsage[0] = MBRCFG_USED_BY_VLAN;
-    vlan_mbrCfgVid[0] = 1;
-
-    /* Enable Ingress filter */
-    RTK_SCAN_ALL_PHY_PORTMASK(i)
-    {
-        if ((retVal = rtl8367c_setAsicVlanIngressFilter(i, ENABLED)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /* enable VLAN */
-    if ((retVal = rtl8367c_setAsicVlanFilter(ENABLED)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_set
- * Description:
- *      Set a VLAN entry.
- * Input:
- *      vid - VLAN ID to configure.
- *      pVlanCfg - VLAN Configuration
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_INPUT                - Invalid input parameters.
- *      RT_ERR_L2_FID               - Invalid FID.
- *      RT_ERR_VLAN_PORT_MBR_EXIST  - Invalid member port mask.
- *      RT_ERR_VLAN_VID             - Invalid VID parameter.
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_set(rtk_vlan_t vid, rtk_vlan_cfg_t *pVlanCfg)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 phyMbrPmask;
-    rtk_uint32 phyUntagPmask;
-    rtl8367c_user_vlan4kentry vlan4K;
-    rtl8367c_vlanconfiguser vlanMC;
-    rtk_uint32 idx;
-    rtk_uint32 empty_index = 0xffff;
-    rtk_uint32 update_evid = 0;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* vid must be 0~8191 */
-    if (vid > RTL8367C_EVIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Null pointer check */
-    if(NULL == pVlanCfg)
-        return RT_ERR_NULL_POINTER;
-
-    /* Check port mask valid */
-    RTK_CHK_PORTMASK_VALID(&(pVlanCfg->mbr));
-
-    if (vid <= RTL8367C_VIDMAX)
-    {
-        /* Check untag port mask valid */
-        RTK_CHK_PORTMASK_VALID(&(pVlanCfg->untag));
-    }
-
-    /* IVL_EN */
-    if(pVlanCfg->ivl_en >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    /* fid must be 0~15 */
-    if(pVlanCfg->fid_msti > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    /* Policing */
-    if(pVlanCfg->envlanpol >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    /* Meter ID */
-    if(pVlanCfg->meteridx > RTK_MAX_METER_ID)
-        return RT_ERR_INPUT;
-
-    /* VLAN based priority */
-    if(pVlanCfg->vbpen >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    /* Priority */
-    if(pVlanCfg->vbpri > RTL8367C_PRIMAX)
-        return RT_ERR_INPUT;
-
-    /* Get physical port mask */
-    if(rtk_switch_portmask_L2P_get(&(pVlanCfg->mbr), &phyMbrPmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    if(rtk_switch_portmask_L2P_get(&(pVlanCfg->untag), &phyUntagPmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    if (vid <= RTL8367C_VIDMAX)
-    {
-        /* update 4K table */
-        memset(&vlan4K, 0, sizeof(rtl8367c_user_vlan4kentry));
-        vlan4K.vid = vid;
-
-        vlan4K.mbr    = (phyMbrPmask & 0xFFFF);
-        vlan4K.untag  = (phyUntagPmask & 0xFFFF);
-
-        vlan4K.ivl_svl      = pVlanCfg->ivl_en;
-        vlan4K.fid_msti     = pVlanCfg->fid_msti;
-        vlan4K.envlanpol    = pVlanCfg->envlanpol;
-        vlan4K.meteridx     = pVlanCfg->meteridx;
-        vlan4K.vbpen        = pVlanCfg->vbpen;
-        vlan4K.vbpri        = pVlanCfg->vbpri;
-
-        if ((retVal = rtl8367c_setAsicVlan4kEntry(&vlan4K)) != RT_ERR_OK)
-            return retVal;
-
-        /* Update Member configuration if exist */
-        for (idx = 0; idx <= RTL8367C_CVIDXMAX; idx++)
-        {
-            if(vlan_mbrCfgUsage[idx] == MBRCFG_USED_BY_VLAN)
-            {
-                if(vlan_mbrCfgVid[idx] == vid)
-                {
-                    /* Found! Update */
-                    if(phyMbrPmask == 0x00)
-                    {
-                        /* Member port = 0x00, delete this VLAN from Member Configuration */
-                        memset(&vlanMC, 0x00, sizeof(rtl8367c_vlanconfiguser));
-                        if ((retVal = rtl8367c_setAsicVlanMemberConfig(idx, &vlanMC)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* Clear Database */
-                        vlan_mbrCfgUsage[idx] = MBRCFG_UNUSED;
-                        vlan_mbrCfgVid[idx]   = 0;
-                    }
-                    else
-                    {
-                        /* Normal VLAN config, update to member configuration */
-                        vlanMC.evid = vid;
-                        vlanMC.mbr = vlan4K.mbr;
-                        vlanMC.fid_msti = vlan4K.fid_msti;
-                        vlanMC.meteridx = vlan4K.meteridx;
-                        vlanMC.envlanpol= vlan4K.envlanpol;
-                        vlanMC.vbpen = vlan4K.vbpen;
-                        vlanMC.vbpri = vlan4K.vbpri;
-                        if ((retVal = rtl8367c_setAsicVlanMemberConfig(idx, &vlanMC)) != RT_ERR_OK)
-                            return retVal;
-                    }
-
-                    break;
-                }
-            }
-        }
-    }
-    else
-    {
-        /* vid > 4095 */
-        for (idx = 0; idx <= RTL8367C_CVIDXMAX; idx++)
-        {
-            if(vlan_mbrCfgUsage[idx] == MBRCFG_USED_BY_VLAN)
-            {
-                if(vlan_mbrCfgVid[idx] == vid)
-                {
-                    /* Found! Update */
-                    if(phyMbrPmask == 0x00)
-                    {
-                        /* Member port = 0x00, delete this VLAN from Member Configuration */
-                        memset(&vlanMC, 0x00, sizeof(rtl8367c_vlanconfiguser));
-                        if ((retVal = rtl8367c_setAsicVlanMemberConfig(idx, &vlanMC)) != RT_ERR_OK)
-                            return retVal;
-
-                        /* Clear Database */
-                        vlan_mbrCfgUsage[idx] = MBRCFG_UNUSED;
-                        vlan_mbrCfgVid[idx]   = 0;
-                    }
-                    else
-                    {
-                        /* Normal VLAN config, update to member configuration */
-                        vlanMC.evid = vid;
-                        vlanMC.mbr = phyMbrPmask;
-                        vlanMC.fid_msti = pVlanCfg->fid_msti;
-                        vlanMC.meteridx = pVlanCfg->meteridx;
-                        vlanMC.envlanpol= pVlanCfg->envlanpol;
-                        vlanMC.vbpen = pVlanCfg->vbpen;
-                        vlanMC.vbpri = pVlanCfg->vbpri;
-                        if ((retVal = rtl8367c_setAsicVlanMemberConfig(idx, &vlanMC)) != RT_ERR_OK)
-                            return retVal;
-
-                        break;
-                    }
-
-                    update_evid = 1;
-                }
-            }
-
-            if(vlan_mbrCfgUsage[idx] == MBRCFG_UNUSED)
-            {
-                if(0xffff == empty_index)
-                    empty_index = idx;
-            }
-        }
-
-        /* doesn't find out same EVID entry and there is empty index in member configuration */
-        if( (phyMbrPmask != 0x00) && (update_evid == 0) && (empty_index != 0xFFFF) )
-        {
-            vlanMC.evid = vid;
-            vlanMC.mbr = phyMbrPmask;
-            vlanMC.fid_msti = pVlanCfg->fid_msti;
-            vlanMC.meteridx = pVlanCfg->meteridx;
-            vlanMC.envlanpol= pVlanCfg->envlanpol;
-            vlanMC.vbpen = pVlanCfg->vbpen;
-            vlanMC.vbpri = pVlanCfg->vbpri;
-            if ((retVal = rtl8367c_setAsicVlanMemberConfig(empty_index, &vlanMC)) != RT_ERR_OK)
-                return retVal;
-
-            vlan_mbrCfgUsage[empty_index] = MBRCFG_USED_BY_VLAN;
-            vlan_mbrCfgVid[empty_index] = vid;
-
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_get
- * Description:
- *      Get a VLAN entry.
- * Input:
- *      vid - VLAN ID to configure.
- * Output:
- *      pVlanCfg - VLAN Configuration
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_get(rtk_vlan_t vid, rtk_vlan_cfg_t *pVlanCfg)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 phyMbrPmask;
-    rtk_uint32 phyUntagPmask;
-    rtl8367c_user_vlan4kentry vlan4K;
-    rtl8367c_vlanconfiguser vlanMC;
-    rtk_uint32 idx;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* vid must be 0~8191 */
-    if (vid > RTL8367C_EVIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Null pointer check */
-    if(NULL == pVlanCfg)
-        return RT_ERR_NULL_POINTER;
-
-    if (vid <= RTL8367C_VIDMAX)
-    {
-        vlan4K.vid = vid;
-
-        if ((retVal = rtl8367c_getAsicVlan4kEntry(&vlan4K)) != RT_ERR_OK)
-            return retVal;
-
-        phyMbrPmask   = vlan4K.mbr;
-        phyUntagPmask = vlan4K.untag;
-        if(rtk_switch_portmask_P2L_get(phyMbrPmask, &(pVlanCfg->mbr)) != RT_ERR_OK)
-            return RT_ERR_FAILED;
-
-        if(rtk_switch_portmask_P2L_get(phyUntagPmask, &(pVlanCfg->untag)) != RT_ERR_OK)
-            return RT_ERR_FAILED;
-
-        pVlanCfg->ivl_en    = vlan4K.ivl_svl;
-        pVlanCfg->fid_msti  = vlan4K.fid_msti;
-        pVlanCfg->envlanpol = vlan4K.envlanpol;
-        pVlanCfg->meteridx  = vlan4K.meteridx;
-        pVlanCfg->vbpen     = vlan4K.vbpen;
-        pVlanCfg->vbpri     = vlan4K.vbpri;
-    }
-    else
-    {
-        for (idx = 0; idx <= RTL8367C_CVIDXMAX; idx++)
-        {
-            if(vlan_mbrCfgUsage[idx] == MBRCFG_USED_BY_VLAN)
-            {
-                if(vlan_mbrCfgVid[idx] == vid)
-                {
-                    if ((retVal = rtl8367c_getAsicVlanMemberConfig(idx, &vlanMC)) != RT_ERR_OK)
-                        return retVal;
-
-                    phyMbrPmask   = vlanMC.mbr;
-                    if(rtk_switch_portmask_P2L_get(phyMbrPmask, &(pVlanCfg->mbr)) != RT_ERR_OK)
-                        return RT_ERR_FAILED;
-
-                    pVlanCfg->untag.bits[0] = 0;
-                    pVlanCfg->ivl_en    = 0;
-                    pVlanCfg->fid_msti  = vlanMC.fid_msti;
-                    pVlanCfg->envlanpol = vlanMC.envlanpol;
-                    pVlanCfg->meteridx  = vlanMC.meteridx;
-                    pVlanCfg->vbpen     = vlanMC.vbpen;
-                    pVlanCfg->vbpri     = vlanMC.vbpri;
-                }
-            }
-        }
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_egrFilterEnable_set
- * Description:
- *      Set VLAN egress filter.
- * Input:
- *      egrFilter - Egress filtering
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_ENABLE       - Invalid input parameters.
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_egrFilterEnable_set(rtk_enable_t egrFilter)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(egrFilter >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    /* enable VLAN */
-    if ((retVal = rtl8367c_setAsicVlanFilter((rtk_uint32)egrFilter)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_egrFilterEnable_get
- * Description:
- *      Get VLAN egress filter.
- * Input:
- *      pEgrFilter - Egress filtering
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - NULL Pointer.
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_egrFilterEnable_get(rtk_enable_t *pEgrFilter)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 state;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEgrFilter)
-        return RT_ERR_NULL_POINTER;
-
-    /* enable VLAN */
-    if ((retVal = rtl8367c_getAsicVlanFilter(&state)) != RT_ERR_OK)
-        return retVal;
-
-    *pEgrFilter = (rtk_enable_t)state;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_mbrCfg_set
- * Description:
- *      Set a VLAN Member Configuration entry by index.
- * Input:
- *      idx     - Index of VLAN Member Configuration.
- *      pMbrcfg - VLAN member Configuration.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *     Set a VLAN Member Configuration entry by index.
- */
-rtk_api_ret_t rtk_vlan_mbrCfg_set(rtk_uint32 idx, rtk_vlan_mbrcfg_t *pMbrcfg)
-{
-    rtk_api_ret_t           retVal;
-    rtk_uint32              phyMbrPmask;
-    rtl8367c_vlanconfiguser mbrCfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Error check */
-    if(pMbrcfg == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(idx > RTL8367C_CVIDXMAX)
-        return RT_ERR_INPUT;
-
-    if(pMbrcfg->evid > RTL8367C_EVIDMAX)
-        return RT_ERR_INPUT;
-
-    if(pMbrcfg->fid_msti > RTL8367C_FIDMAX)
-        return RT_ERR_L2_FID;
-
-    if(pMbrcfg->envlanpol >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pMbrcfg->meteridx > RTK_MAX_METER_ID)
-        return RT_ERR_FILTER_METER_ID;
-
-    if(pMbrcfg->vbpen >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if(pMbrcfg->vbpri > RTL8367C_PRIMAX)
-        return RT_ERR_QOS_INT_PRIORITY;
-
-    /* Check port mask valid */
-    RTK_CHK_PORTMASK_VALID(&(pMbrcfg->mbr));
-
-    mbrCfg.evid         = pMbrcfg->evid;
-    mbrCfg.fid_msti     = pMbrcfg->fid_msti;
-    mbrCfg.envlanpol    = pMbrcfg->envlanpol;
-    mbrCfg.meteridx     = pMbrcfg->meteridx;
-    mbrCfg.vbpen        = pMbrcfg->vbpen;
-    mbrCfg.vbpri        = pMbrcfg->vbpri;
-
-    if(rtk_switch_portmask_L2P_get(&(pMbrcfg->mbr), &phyMbrPmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    mbrCfg.mbr = phyMbrPmask;
-
-    if ((retVal = rtl8367c_setAsicVlanMemberConfig(idx, &mbrCfg)) != RT_ERR_OK)
-        return retVal;
-
-    /* Update Database */
-    if( (mbrCfg.evid == 0) && (mbrCfg.mbr == 0) )
-    {
-        vlan_mbrCfgUsage[idx] = MBRCFG_UNUSED;
-        vlan_mbrCfgVid[idx] = 0;
-    }
-    else
-    {
-        vlan_mbrCfgUsage[idx] = MBRCFG_USED_BY_VLAN;
-        vlan_mbrCfgVid[idx] = mbrCfg.evid;
-    }
-
-    return RT_ERR_OK;
-
-}
-
-/* Function Name:
- *      rtk_vlan_mbrCfg_get
- * Description:
- *      Get a VLAN Member Configuration entry by index.
- * Input:
- *      idx - Index of VLAN Member Configuration.
- * Output:
- *      pMbrcfg - VLAN member Configuration.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *     Get a VLAN Member Configuration entry by index.
- */
-rtk_api_ret_t rtk_vlan_mbrCfg_get(rtk_uint32 idx, rtk_vlan_mbrcfg_t *pMbrcfg)
-{
-    rtk_api_ret_t           retVal;
-    rtk_uint32              phyMbrPmask;
-    rtl8367c_vlanconfiguser mbrCfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Error check */
-    if(pMbrcfg == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(idx > RTL8367C_CVIDXMAX)
-        return RT_ERR_INPUT;
-
-    memset(&mbrCfg, 0x00, sizeof(rtl8367c_vlanconfiguser));
-    if ((retVal = rtl8367c_getAsicVlanMemberConfig(idx, &mbrCfg)) != RT_ERR_OK)
-        return retVal;
-
-    pMbrcfg->evid       = mbrCfg.evid;
-    pMbrcfg->fid_msti   = mbrCfg.fid_msti;
-    pMbrcfg->envlanpol  = mbrCfg.envlanpol;
-    pMbrcfg->meteridx   = mbrCfg.meteridx;
-    pMbrcfg->vbpen      = mbrCfg.vbpen;
-    pMbrcfg->vbpri      = mbrCfg.vbpri;
-
-    phyMbrPmask = mbrCfg.mbr;
-    if(rtk_switch_portmask_P2L_get(phyMbrPmask, &(pMbrcfg->mbr)) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *     rtk_vlan_portPvid_set
- * Description:
- *      Set port to specified VLAN ID(PVID).
- * Input:
- *      port - Port id.
- *      pvid - Specified VLAN ID.
- *      priority - 802.1p priority for the PVID.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                   - OK
- *      RT_ERR_FAILED               - Failed
- *      RT_ERR_SMI                  - SMI access error
- *      RT_ERR_PORT_ID              - Invalid port number.
- *      RT_ERR_VLAN_PRIORITY        - Invalid priority.
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - VLAN entry not found.
- *      RT_ERR_VLAN_VID             - Invalid VID parameter.
- * Note:
- *       The API is used for Port-based VLAN. The untagged frame received from the
- *       port will be classified to the specified VLAN and assigned to the specified priority.
- */
-rtk_api_ret_t rtk_vlan_portPvid_set(rtk_port_t port, rtk_vlan_t pvid, rtk_pri_t priority)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 index;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    /* vid must be 0~8191 */
-    if (pvid > RTL8367C_EVIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* priority must be 0~7 */
-    if (priority > RTL8367C_PRIMAX)
-        return RT_ERR_VLAN_PRIORITY;
-
-    if((retVal = rtk_vlan_checkAndCreateMbr(pvid, &index)) != RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicVlanPortBasedVID(rtk_switch_port_L2P_get(port), index, priority)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_portPvid_get
- * Description:
- *      Get VLAN ID(PVID) on specified port.
- * Input:
- *      port - Port id.
- * Output:
- *      pPvid - Specified VLAN ID.
- *      pPriority - 802.1p priority for the PVID.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *     The API can get the PVID and 802.1p priority for the PVID of Port-based VLAN.
- */
-rtk_api_ret_t rtk_vlan_portPvid_get(rtk_port_t port, rtk_vlan_t *pPvid, rtk_pri_t *pPriority)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 index, pri;
-    rtl8367c_vlanconfiguser mbrCfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pPvid)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pPriority)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicVlanPortBasedVID(rtk_switch_port_L2P_get(port), &index, &pri)) != RT_ERR_OK)
-        return retVal;
-
-    memset(&mbrCfg, 0x00, sizeof(rtl8367c_vlanconfiguser));
-    if ((retVal = rtl8367c_getAsicVlanMemberConfig(index, &mbrCfg)) != RT_ERR_OK)
-        return retVal;
-
-    *pPvid = mbrCfg.evid;
-    *pPriority = pri;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_portIgrFilterEnable_set
- * Description:
- *      Set VLAN ingress for each port.
- * Input:
- *      port - Port id.
- *      igr_filter - VLAN ingress function enable status.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number
- *      RT_ERR_ENABLE       - Invalid enable input
- * Note:
- *      The status of vlan ingress filter is as following:
- *      - DISABLED
- *      - ENABLED
- *      While VLAN function is enabled, ASIC will decide VLAN ID for each received frame and get belonged member
- *      ports from VLAN table. If received port is not belonged to VLAN member ports, ASIC will drop received frame if VLAN ingress function is enabled.
- */
-rtk_api_ret_t rtk_vlan_portIgrFilterEnable_set(rtk_port_t port, rtk_enable_t igr_filter)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (igr_filter >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicVlanIngressFilter(rtk_switch_port_L2P_get(port), igr_filter)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_portIgrFilterEnable_get
- * Description:
- *      Get VLAN Ingress Filter
- * Input:
- *      port        - Port id.
- * Output:
- *      pIgr_filter - VLAN ingress function enable status.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *     The API can Get the VLAN ingress filter status.
- *     The status of vlan ingress filter is as following:
- *     - DISABLED
- *     - ENABLED
- */
-rtk_api_ret_t rtk_vlan_portIgrFilterEnable_get(rtk_port_t port, rtk_enable_t *pIgr_filter)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pIgr_filter)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicVlanIngressFilter(rtk_switch_port_L2P_get(port), pIgr_filter)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_portAcceptFrameType_set
- * Description:
- *      Set VLAN accept_frame_type
- * Input:
- *      port                - Port id.
- *      accept_frame_type   - accept frame type
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK                       - OK
- *      RT_ERR_FAILED                   - Failed
- *      RT_ERR_SMI                      - SMI access error
- *      RT_ERR_PORT_ID                  - Invalid port number.
- *      RT_ERR_VLAN_ACCEPT_FRAME_TYPE   - Invalid frame type.
- * Note:
- *      The API is used for checking 802.1Q tagged frames.
- *      The accept frame type as following:
- *      - ACCEPT_FRAME_TYPE_ALL
- *      - ACCEPT_FRAME_TYPE_TAG_ONLY
- *      - ACCEPT_FRAME_TYPE_UNTAG_ONLY
- */
-rtk_api_ret_t rtk_vlan_portAcceptFrameType_set(rtk_port_t port, rtk_vlan_acceptFrameType_t accept_frame_type)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (accept_frame_type >= ACCEPT_FRAME_TYPE_END)
-        return RT_ERR_VLAN_ACCEPT_FRAME_TYPE;
-
-    if ((retVal = rtl8367c_setAsicVlanAccpetFrameType(rtk_switch_port_L2P_get(port), (rtl8367c_accframetype)accept_frame_type)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_portAcceptFrameType_get
- * Description:
- *      Get VLAN accept_frame_type
- * Input:
- *      port - Port id.
- * Output:
- *      pAccept_frame_type - accept frame type
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *     The API can Get the VLAN ingress filter.
- *     The accept frame type as following:
- *     - ACCEPT_FRAME_TYPE_ALL
- *     - ACCEPT_FRAME_TYPE_TAG_ONLY
- *     - ACCEPT_FRAME_TYPE_UNTAG_ONLY
- */
-rtk_api_ret_t rtk_vlan_portAcceptFrameType_get(rtk_port_t port, rtk_vlan_acceptFrameType_t *pAccept_frame_type)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_accframetype   acc_frm_type;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pAccept_frame_type)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicVlanAccpetFrameType(rtk_switch_port_L2P_get(port), &acc_frm_type)) != RT_ERR_OK)
-        return retVal;
-
-    *pAccept_frame_type = (rtk_vlan_acceptFrameType_t)acc_frm_type;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_add
- * Description:
- *      Add the protocol-and-port-based vlan to the specified port of device.
- * Input:
- *      port  - Port id.
- *      pInfo - Protocol and port based VLAN configuration information.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_VLAN_VID         - Invalid VID parameter.
- *      RT_ERR_VLAN_PRIORITY    - Invalid priority.
- *      RT_ERR_TBL_FULL         - Table is full.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *      The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *      The frame type is shown in the following:
- *      - FRAME_TYPE_ETHERNET
- *      - FRAME_TYPE_RFC1042
- *      - FRAME_TYPE_LLCOTHER
- */
-rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_add(rtk_port_t port, rtk_vlan_protoAndPortInfo_t *pInfo)
-{
-    rtk_api_ret_t retVal, i;
-    rtk_uint32 exist, empty, used, index;
-    rtl8367c_protocolgdatacfg ppb_data_cfg;
-    rtl8367c_protocolvlancfg ppb_vlan_cfg;
-    rtl8367c_provlan_frametype tmp;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pInfo)
-        return RT_ERR_NULL_POINTER;
-
-    if (pInfo->proto_type > RTK_MAX_NUM_OF_PROTO_TYPE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if (pInfo->frame_type >= FRAME_TYPE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if (pInfo->cvid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    if (pInfo->cpri > RTL8367C_PRIMAX)
-        return RT_ERR_VLAN_PRIORITY;
-
-    exist = 0xFF;
-    empty = 0xFF;
-    for (i = RTL8367C_PROTOVLAN_GIDX_MAX; i >= 0; i--)
-    {
-        if ((retVal = rtl8367c_getAsicVlanProtocolBasedGroupData(i, &ppb_data_cfg)) != RT_ERR_OK)
-            return retVal;
-        tmp = pInfo->frame_type;
-        if (ppb_data_cfg.etherType == pInfo->proto_type && ppb_data_cfg.frameType == tmp)
-        {
-            /*Already exist*/
-            exist = i;
-            break;
-        }
-        else if (ppb_data_cfg.etherType == 0 && ppb_data_cfg.frameType == 0)
-        {
-            /*find empty index*/
-            empty = i;
-        }
-    }
-
-    used = 0xFF;
-    /*No empty and exist index*/
-    if (0xFF == exist && 0xFF == empty)
-        return RT_ERR_TBL_FULL;
-    else if (exist<RTL8367C_PROTOVLAN_GROUPNO)
-    {
-       /*exist index*/
-       used = exist;
-    }
-    else if (empty<RTL8367C_PROTOVLAN_GROUPNO)
-    {
-        /*No exist index, but have empty index*/
-        ppb_data_cfg.frameType = pInfo->frame_type;
-        ppb_data_cfg.etherType = pInfo->proto_type;
-        if ((retVal = rtl8367c_setAsicVlanProtocolBasedGroupData(empty, &ppb_data_cfg)) != RT_ERR_OK)
-            return retVal;
-        used = empty;
-    }
-    else
-        return RT_ERR_FAILED;
-
-    if((retVal = rtk_vlan_checkAndCreateMbr(pInfo->cvid, &index)) != RT_ERR_OK)
-        return retVal;
-
-    ppb_vlan_cfg.vlan_idx = index;
-    ppb_vlan_cfg.valid = TRUE;
-    ppb_vlan_cfg.priority = pInfo->cpri;
-    if ((retVal = rtl8367c_setAsicVlanPortAndProtocolBased(rtk_switch_port_L2P_get(port), used, &ppb_vlan_cfg)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_get
- * Description:
- *      Get the protocol-and-port-based vlan to the specified port of device.
- * Input:
- *      port - Port id.
- *      proto_type - protocol-and-port-based vlan protocol type.
- *      frame_type - protocol-and-port-based vlan frame type.
- * Output:
- *      pInfo - Protocol and port based VLAN configuration information.
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- *      RT_ERR_TBL_FULL         - Table is full.
- * Note:
- *     The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *     The frame type is shown in the following:
- *      - FRAME_TYPE_ETHERNET
- *      - FRAME_TYPE_RFC1042
- *      - FRAME_TYPE_LLCOTHER
- */
-rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_get(rtk_port_t port, rtk_vlan_proto_type_t proto_type, rtk_vlan_protoVlan_frameType_t frame_type, rtk_vlan_protoAndPortInfo_t *pInfo)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i;
-    rtk_uint32 ppb_idx;
-    rtl8367c_protocolgdatacfg ppb_data_cfg;
-    rtl8367c_protocolvlancfg ppb_vlan_cfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (proto_type > RTK_MAX_NUM_OF_PROTO_TYPE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if (frame_type >= FRAME_TYPE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-   ppb_idx = 0;
-
-    for (i = 0; i<= RTL8367C_PROTOVLAN_GIDX_MAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicVlanProtocolBasedGroupData(i, &ppb_data_cfg)) != RT_ERR_OK)
-            return retVal;
-
-        if ( (ppb_data_cfg.frameType == (rtl8367c_provlan_frametype)frame_type) && (ppb_data_cfg.etherType == proto_type) )
-        {
-            ppb_idx = i;
-            break;
-        }
-        else if (RTL8367C_PROTOVLAN_GIDX_MAX == i)
-            return RT_ERR_TBL_FULL;
-    }
-
-    if ((retVal = rtl8367c_getAsicVlanPortAndProtocolBased(rtk_switch_port_L2P_get(port), ppb_idx, &ppb_vlan_cfg)) != RT_ERR_OK)
-        return retVal;
-
-    if (FALSE == ppb_vlan_cfg.valid)
-        return RT_ERR_FAILED;
-
-    pInfo->frame_type = frame_type;
-    pInfo->proto_type = proto_type;
-    pInfo->cvid = vlan_mbrCfgVid[ppb_vlan_cfg.vlan_idx];
-    pInfo->cpri = ppb_vlan_cfg.priority;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_del
- * Description:
- *      Delete the protocol-and-port-based vlan from the specified port of device.
- * Input:
- *      port        - Port id.
- *      proto_type  - protocol-and-port-based vlan protocol type.
- *      frame_type  - protocol-and-port-based vlan frame type.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- *      RT_ERR_TBL_FULL         - Table is full.
- * Note:
- *     The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *     The frame type is shown in the following:
- *      - FRAME_TYPE_ETHERNET
- *      - FRAME_TYPE_RFC1042
- *      - FRAME_TYPE_LLCOTHER
- */
-rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_del(rtk_port_t port, rtk_vlan_proto_type_t proto_type, rtk_vlan_protoVlan_frameType_t frame_type)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i, bUsed;
-    rtk_uint32 ppb_idx;
-    rtl8367c_protocolgdatacfg ppb_data_cfg;
-    rtl8367c_protocolvlancfg ppb_vlan_cfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (proto_type > RTK_MAX_NUM_OF_PROTO_TYPE)
-        return RT_ERR_OUT_OF_RANGE;
-
-    if (frame_type >= FRAME_TYPE_END)
-        return RT_ERR_OUT_OF_RANGE;
-
-   ppb_idx = 0;
-
-    for (i = 0; i<= RTL8367C_PROTOVLAN_GIDX_MAX; i++)
-    {
-        if ((retVal = rtl8367c_getAsicVlanProtocolBasedGroupData(i, &ppb_data_cfg)) != RT_ERR_OK)
-            return retVal;
-
-        if ( (ppb_data_cfg.frameType == (rtl8367c_provlan_frametype)frame_type) && (ppb_data_cfg.etherType == proto_type) )
-        {
-            ppb_idx = i;
-            ppb_vlan_cfg.valid = FALSE;
-            ppb_vlan_cfg.vlan_idx = 0;
-            ppb_vlan_cfg.priority = 0;
-            if ((retVal = rtl8367c_setAsicVlanPortAndProtocolBased(rtk_switch_port_L2P_get(port), ppb_idx, &ppb_vlan_cfg)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-
-    bUsed = FALSE;
-    RTK_SCAN_ALL_PHY_PORTMASK(i)
-    {
-        if ((retVal = rtl8367c_getAsicVlanPortAndProtocolBased(i, ppb_idx, &ppb_vlan_cfg)) != RT_ERR_OK)
-            return retVal;
-
-        if (TRUE == ppb_vlan_cfg.valid)
-        {
-            bUsed = TRUE;
-                break;
-        }
-    }
-
-    if (FALSE == bUsed) /*No Port use this PPB Index, Delete it*/
-    {
-        ppb_data_cfg.etherType=0;
-        ppb_data_cfg.frameType=0;
-        if ((retVal = rtl8367c_setAsicVlanProtocolBasedGroupData(ppb_idx, &ppb_data_cfg)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_protoAndPortBasedVlan_delAll
- * Description:
- *     Delete all protocol-and-port-based vlans from the specified port of device.
- * Input:
- *      port - Port id.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK               - OK
- *      RT_ERR_FAILED           - Failed
- *      RT_ERR_SMI              - SMI access error
- *      RT_ERR_PORT_ID          - Invalid port number.
- *      RT_ERR_OUT_OF_RANGE     - input out of range.
- * Note:
- *     The incoming packet which match the protocol-and-port-based vlan will use the configure vid for ingress pipeline
- *     Delete all flow table protocol-and-port-based vlan entries.
- */
-rtk_api_ret_t rtk_vlan_protoAndPortBasedVlan_delAll(rtk_port_t port)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32 i, j, bUsed[4];
-    rtl8367c_protocolgdatacfg ppb_data_cfg;
-    rtl8367c_protocolvlancfg ppb_vlan_cfg;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    for (i = 0; i<= RTL8367C_PROTOVLAN_GIDX_MAX; i++)
-    {
-        ppb_vlan_cfg.valid = FALSE;
-        ppb_vlan_cfg.vlan_idx = 0;
-        ppb_vlan_cfg.priority = 0;
-        if ((retVal = rtl8367c_setAsicVlanPortAndProtocolBased(rtk_switch_port_L2P_get(port), i, &ppb_vlan_cfg)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    bUsed[0] = FALSE;
-    bUsed[1] = FALSE;
-    bUsed[2] = FALSE;
-    bUsed[3] = FALSE;
-    RTK_SCAN_ALL_PHY_PORTMASK(i)
-    {
-        for (j = 0; j <= RTL8367C_PROTOVLAN_GIDX_MAX; j++)
-        {
-            if ((retVal = rtl8367c_getAsicVlanPortAndProtocolBased(i,j, &ppb_vlan_cfg)) != RT_ERR_OK)
-                return retVal;
-
-            if (TRUE == ppb_vlan_cfg.valid)
-            {
-                bUsed[j] = TRUE;
-            }
-        }
-    }
-
-    for (i = 0; i<= RTL8367C_PROTOVLAN_GIDX_MAX; i++)
-    {
-        if (FALSE == bUsed[i]) /*No Port use this PPB Index, Delete it*/
-        {
-            ppb_data_cfg.etherType=0;
-            ppb_data_cfg.frameType=0;
-            if ((retVal = rtl8367c_setAsicVlanProtocolBasedGroupData(i, &ppb_data_cfg)) != RT_ERR_OK)
-                return retVal;
-        }
-    }
-
-
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_tagMode_set
- * Description:
- *      Set CVLAN egress tag mode
- * Input:
- *      port        - Port id.
- *      tag_mode    - The egress tag mode.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_ENABLE       - Invalid enable input.
- * Note:
- *      The API can set Egress tag mode. There are 4 mode for egress tag:
- *      - VLAN_TAG_MODE_ORIGINAL,
- *      - VLAN_TAG_MODE_KEEP_FORMAT,
- *      - VLAN_TAG_MODE_PRI.
- *      - VLAN_TAG_MODE_REAL_KEEP_FORMAT,
- */
-rtk_api_ret_t rtk_vlan_tagMode_set(rtk_port_t port, rtk_vlan_tagMode_t tag_mode)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (tag_mode >= VLAN_TAG_MODE_END)
-        return RT_ERR_PORT_ID;
-
-    if ((retVal = rtl8367c_setAsicVlanEgressTagMode(rtk_switch_port_L2P_get(port), tag_mode)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_tagMode_get
- * Description:
- *      Get CVLAN egress tag mode
- * Input:
- *      port - Port id.
- * Output:
- *      pTag_mode - The egress tag mode.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      The API can get Egress tag mode. There are 4 mode for egress tag:
- *      - VLAN_TAG_MODE_ORIGINAL,
- *      - VLAN_TAG_MODE_KEEP_FORMAT,
- *      - VLAN_TAG_MODE_PRI.
- *      - VLAN_TAG_MODE_REAL_KEEP_FORMAT,
- */
-rtk_api_ret_t rtk_vlan_tagMode_get(rtk_port_t port, rtk_vlan_tagMode_t *pTag_mode)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_egtagmode  mode;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pTag_mode)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicVlanEgressTagMode(rtk_switch_port_L2P_get(port), &mode)) != RT_ERR_OK)
-        return retVal;
-
-    *pTag_mode = (rtk_vlan_tagMode_t)mode;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_transparent_set
- * Description:
- *      Set VLAN transparent mode
- * Input:
- *      egr_port        - Egress Port id.
- *      pIgr_pmask      - Ingress Port Mask.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_vlan_transparent_set(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask)
-{
-     rtk_api_ret_t retVal;
-     rtk_uint32    pmask;
-
-     /* Check initialization state */
-     RTK_CHK_INIT_STATE();
-
-     /* Check Port Valid */
-     RTK_CHK_PORT_VALID(egr_port);
-
-     if(NULL == pIgr_pmask)
-        return RT_ERR_NULL_POINTER;
-
-     RTK_CHK_PORTMASK_VALID(pIgr_pmask);
-
-     if(rtk_switch_portmask_L2P_get(pIgr_pmask, &pmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-     if ((retVal = rtl8367c_setAsicVlanTransparent(rtk_switch_port_L2P_get(egr_port), pmask)) != RT_ERR_OK)
-         return retVal;
-
-     return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_transparent_get
- * Description:
- *      Get VLAN transparent mode
- * Input:
- *      egr_port        - Egress Port id.
- * Output:
- *      pIgr_pmask      - Ingress Port Mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_vlan_transparent_get(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask)
-{
-     rtk_api_ret_t retVal;
-     rtk_uint32    pmask;
-
-     /* Check initialization state */
-     RTK_CHK_INIT_STATE();
-
-     /* Check Port Valid */
-     RTK_CHK_PORT_VALID(egr_port);
-
-     if(NULL == pIgr_pmask)
-        return RT_ERR_NULL_POINTER;
-
-     if ((retVal = rtl8367c_getAsicVlanTransparent(rtk_switch_port_L2P_get(egr_port), &pmask)) != RT_ERR_OK)
-         return retVal;
-
-     if(rtk_switch_portmask_P2L_get(pmask, pIgr_pmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-     return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_keep_set
- * Description:
- *      Set VLAN egress keep mode
- * Input:
- *      egr_port        - Egress Port id.
- *      pIgr_pmask      - Ingress Port Mask.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_vlan_keep_set(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask)
-{
-     rtk_api_ret_t retVal;
-     rtk_uint32    pmask;
-
-     /* Check initialization state */
-     RTK_CHK_INIT_STATE();
-
-     /* Check Port Valid */
-     RTK_CHK_PORT_VALID(egr_port);
-
-     if(NULL == pIgr_pmask)
-        return RT_ERR_NULL_POINTER;
-
-     RTK_CHK_PORTMASK_VALID(pIgr_pmask);
-
-     if(rtk_switch_portmask_L2P_get(pIgr_pmask, &pmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-     if ((retVal = rtl8367c_setAsicVlanEgressKeep(rtk_switch_port_L2P_get(egr_port), pmask)) != RT_ERR_OK)
-         return retVal;
-
-     return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_keep_get
- * Description:
- *      Get VLAN egress keep mode
- * Input:
- *      egr_port        - Egress Port id.
- * Output:
- *      pIgr_pmask      - Ingress Port Mask
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_PORT_ID      - Invalid port number.
- * Note:
- *      None.
- */
-rtk_api_ret_t rtk_vlan_keep_get(rtk_port_t egr_port, rtk_portmask_t *pIgr_pmask)
-{
-     rtk_api_ret_t retVal;
-     rtk_uint32    pmask;
-
-     /* Check initialization state */
-     RTK_CHK_INIT_STATE();
-
-     /* Check Port Valid */
-     RTK_CHK_PORT_VALID(egr_port);
-
-     if(NULL == pIgr_pmask)
-        return RT_ERR_NULL_POINTER;
-
-     if ((retVal = rtl8367c_getAsicVlanEgressKeep(rtk_switch_port_L2P_get(egr_port), &pmask)) != RT_ERR_OK)
-         return retVal;
-
-     if(rtk_switch_portmask_P2L_get(pmask, pIgr_pmask) != RT_ERR_OK)
-        return RT_ERR_FAILED;
-
-     return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_stg_set
- * Description:
- *      Set spanning tree group instance of the vlan to the specified device
- * Input:
- *      vid - Specified VLAN ID.
- *      stg - spanning tree group instance.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_MSTI         - Invalid msti parameter
- *      RT_ERR_INPUT        - Invalid input parameter.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *      The API can set spanning tree group instance of the vlan to the specified device.
- */
-rtk_api_ret_t rtk_vlan_stg_set(rtk_vlan_t vid, rtk_stp_msti_id_t stg)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_user_vlan4kentry vlan4K;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* vid must be 0~4095 */
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* priority must be 0~15 */
-    if (stg > RTL8367C_MSTIMAX)
-        return RT_ERR_MSTI;
-
-    /* update 4K table */
-    vlan4K.vid = vid;
-    if ((retVal = rtl8367c_getAsicVlan4kEntry(&vlan4K)) != RT_ERR_OK)
-        return retVal;
-
-    vlan4K.fid_msti= stg;
-    if ((retVal = rtl8367c_setAsicVlan4kEntry(&vlan4K)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_stg_get
- * Description:
- *      Get spanning tree group instance of the vlan to the specified device
- * Input:
- *      vid - Specified VLAN ID.
- * Output:
- *      pStg - spanning tree group instance.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Invalid input parameters.
- *      RT_ERR_VLAN_VID     - Invalid VID parameter.
- * Note:
- *      The API can get spanning tree group instance of the vlan to the specified device.
- */
-rtk_api_ret_t rtk_vlan_stg_get(rtk_vlan_t vid, rtk_stp_msti_id_t *pStg)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_user_vlan4kentry vlan4K;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* vid must be 0~4095 */
-    if (vid > RTL8367C_VIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    if(NULL == pStg)
-        return RT_ERR_NULL_POINTER;
-
-    /* update 4K table */
-    vlan4K.vid = vid;
-    if ((retVal = rtl8367c_getAsicVlan4kEntry(&vlan4K)) != RT_ERR_OK)
-        return retVal;
-
-    *pStg = vlan4K.fid_msti;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_portFid_set
- * Description:
- *      Set port-based filtering database
- * Input:
- *      port - Port id.
- *      enable - ebable port-based FID
- *      fid - Specified filtering database.
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_L2_FID - Invalid fid.
- *      RT_ERR_INPUT - Invalid input parameter.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can set port-based filtering database. If the function is enabled, all input
- *      packets will be assigned to the port-based fid regardless vlan tag.
- */
-rtk_api_ret_t rtk_vlan_portFid_set(rtk_port_t port, rtk_enable_t enable, rtk_fid_t fid)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (enable>=RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    /* fid must be 0~4095 */
-    if (fid > RTK_FID_MAX)
-        return RT_ERR_L2_FID;
-
-    if ((retVal = rtl8367c_setAsicPortBasedFidEn(rtk_switch_port_L2P_get(port), enable))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_setAsicPortBasedFid(rtk_switch_port_L2P_get(port), fid))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_portFid_get
- * Description:
- *      Get port-based filtering database
- * Input:
- *      port - Port id.
- * Output:
- *      pEnable - ebable port-based FID
- *      pFid - Specified filtering database.
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_INPUT - Invalid input parameters.
- *      RT_ERR_PORT_ID - Invalid port ID.
- * Note:
- *      The API can get port-based filtering database status. If the function is enabled, all input
- *      packets will be assigned to the port-based fid regardless vlan tag.
- */
-rtk_api_ret_t rtk_vlan_portFid_get(rtk_port_t port, rtk_enable_t *pEnable, rtk_fid_t *pFid)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if(NULL == pFid)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicPortBasedFidEn(rtk_switch_port_L2P_get(port), pEnable))!=RT_ERR_OK)
-        return retVal;
-
-    if ((retVal = rtl8367c_getAsicPortBasedFid(rtk_switch_port_L2P_get(port), pFid))!=RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_UntagDscpPriorityEnable_set
- * Description:
- *      Set Untag DSCP priority assign
- * Input:
- *      enable - state of Untag DSCP priority assign
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_ENABLE          - Invalid input parameters.
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_UntagDscpPriorityEnable_set(rtk_enable_t enable)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(enable >= RTK_ENABLE_END)
-        return RT_ERR_ENABLE;
-
-    if ((retVal = rtl8367c_setAsicVlanUntagDscpPriorityEn((rtk_uint32)enable)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_UntagDscpPriorityEnable_get
- * Description:
- *      Get Untag DSCP priority assign
- * Input:
- *      None
- * Output:
- *      pEnable - state of Untag DSCP priority assign
- * Return:
- *      RT_ERR_OK              - OK
- *      RT_ERR_FAILED          - Failed
- *      RT_ERR_SMI             - SMI access error
- *      RT_ERR_NULL_POINTER    - Null pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_UntagDscpPriorityEnable_get(rtk_enable_t *pEnable)
-{
-    rtk_api_ret_t retVal;
-    rtk_uint32  value;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnable)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicVlanUntagDscpPriorityEn(&value)) != RT_ERR_OK)
-        return retVal;
-
-    *pEnable = (rtk_enable_t)value;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stp_mstpState_set
- * Description:
- *      Configure spanning tree state per each port.
- * Input:
- *      port - Port id
- *      msti - Multiple spanning tree instance.
- *      stp_state - Spanning tree state for msti
- * Output:
- *      None
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_MSTI         - Invalid msti parameter.
- *      RT_ERR_MSTP_STATE   - Invalid STP state.
- * Note:
- *      System supports per-port multiple spanning tree state for each msti.
- *      There are four states supported by ASIC.
- *      - STP_STATE_DISABLED
- *      - STP_STATE_BLOCKING
- *      - STP_STATE_LEARNING
- *      - STP_STATE_FORWARDING
- */
-rtk_api_ret_t rtk_stp_mstpState_set(rtk_stp_msti_id_t msti, rtk_port_t port, rtk_stp_state_t stp_state)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (msti > RTK_MAX_NUM_OF_MSTI)
-        return RT_ERR_MSTI;
-
-    if (stp_state >= STP_STATE_END)
-        return RT_ERR_MSTP_STATE;
-
-    if ((retVal = rtl8367c_setAsicSpanningTreeStatus(rtk_switch_port_L2P_get(port), msti, stp_state)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_stp_mstpState_get
- * Description:
- *      Get spanning tree state per each port.
- * Input:
- *      port - Port id.
- *      msti - Multiple spanning tree instance.
- * Output:
- *      pStp_state - Spanning tree state for msti
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_PORT_ID      - Invalid port number.
- *      RT_ERR_MSTI         - Invalid msti parameter.
- * Note:
- *      System supports per-port multiple spanning tree state for each msti.
- *      There are four states supported by ASIC.
- *      - STP_STATE_DISABLED
- *      - STP_STATE_BLOCKING
- *      - STP_STATE_LEARNING
- *      - STP_STATE_FORWARDING
- */
-rtk_api_ret_t rtk_stp_mstpState_get(rtk_stp_msti_id_t msti, rtk_port_t port, rtk_stp_state_t *pStp_state)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* Check Port Valid */
-    RTK_CHK_PORT_VALID(port);
-
-    if (msti > RTK_MAX_NUM_OF_MSTI)
-        return RT_ERR_MSTI;
-
-    if(NULL == pStp_state)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getAsicSpanningTreeStatus(rtk_switch_port_L2P_get(port), msti, pStp_state)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_checkAndCreateMbr
- * Description:
- *      Check and create Member configuration and return index
- * Input:
- *      vid  - VLAN id.
- * Output:
- *      pIndex  - Member configuration index
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_VLAN_VID     - Invalid VLAN ID.
- *      RT_ERR_VLAN_ENTRY_NOT_FOUND - VLAN not found
- *      RT_ERR_TBL_FULL     - Member Configuration table full
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_checkAndCreateMbr(rtk_vlan_t vid, rtk_uint32 *pIndex)
-{
-    rtk_api_ret_t retVal;
-    rtl8367c_user_vlan4kentry vlan4K;
-    rtl8367c_vlanconfiguser vlanMC;
-    rtk_uint32 idx;
-    rtk_uint32 empty_idx = 0xFFFF;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    /* vid must be 0~8191 */
-    if (vid > RTL8367C_EVIDMAX)
-        return RT_ERR_VLAN_VID;
-
-    /* Null pointer check */
-    if(NULL == pIndex)
-        return RT_ERR_NULL_POINTER;
-
-    /* Get 4K VLAN */
-    if (vid <= RTL8367C_VIDMAX)
-    {
-        memset(&vlan4K, 0x00, sizeof(rtl8367c_user_vlan4kentry));
-        vlan4K.vid = vid;
-        if ((retVal = rtl8367c_getAsicVlan4kEntry(&vlan4K)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /* Search exist entry */
-    for (idx = 0; idx <= RTL8367C_CVIDXMAX; idx++)
-    {
-        if(vlan_mbrCfgUsage[idx] == MBRCFG_USED_BY_VLAN)
-        {
-            if(vlan_mbrCfgVid[idx] == vid)
-            {
-                /* Found! return index */
-                *pIndex = idx;
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    /* Not found, Read H/W Member Configuration table to update database */
-    for (idx = 0; idx <= RTL8367C_CVIDXMAX; idx++)
-    {
-        if ((retVal = rtl8367c_getAsicVlanMemberConfig(idx, &vlanMC)) != RT_ERR_OK)
-            return retVal;
-
-        if( (vlanMC.evid == 0) && (vlanMC.mbr == 0x00))
-        {
-            vlan_mbrCfgUsage[idx]   = MBRCFG_UNUSED;
-            vlan_mbrCfgVid[idx]     = 0;
-        }
-        else
-        {
-            vlan_mbrCfgUsage[idx]   = MBRCFG_USED_BY_VLAN;
-            vlan_mbrCfgVid[idx]     = vlanMC.evid;
-        }
-    }
-
-    /* Search exist entry again */
-    for (idx = 0; idx <= RTL8367C_CVIDXMAX; idx++)
-    {
-        if(vlan_mbrCfgUsage[idx] == MBRCFG_USED_BY_VLAN)
-        {
-            if(vlan_mbrCfgVid[idx] == vid)
-            {
-                /* Found! return index */
-                *pIndex = idx;
-                return RT_ERR_OK;
-            }
-        }
-    }
-
-    /* try to look up an empty index */
-    for (idx = 0; idx <= RTL8367C_CVIDXMAX; idx++)
-    {
-        if(vlan_mbrCfgUsage[idx] == MBRCFG_UNUSED)
-        {
-            empty_idx = idx;
-            break;
-        }
-    }
-
-    if(empty_idx == 0xFFFF)
-    {
-        /* No empty index */
-        return RT_ERR_TBL_FULL;
-    }
-
-    if (vid > RTL8367C_VIDMAX)
-    {
-        /* > 4K, there is no 4K entry, create on member configuration directly */
-        memset(&vlanMC, 0x00, sizeof(rtl8367c_vlanconfiguser));
-        vlanMC.evid = vid;
-        if ((retVal = rtl8367c_setAsicVlanMemberConfig(empty_idx, &vlanMC)) != RT_ERR_OK)
-            return retVal;
-    }
-    else
-    {
-        /* Copy from 4K table */
-        vlanMC.evid = vid;
-        vlanMC.mbr = vlan4K.mbr;
-        vlanMC.fid_msti = vlan4K.fid_msti;
-        vlanMC.meteridx= vlan4K.meteridx;
-        vlanMC.envlanpol= vlan4K.envlanpol;
-        vlanMC.vbpen = vlan4K.vbpen;
-        vlanMC.vbpri = vlan4K.vbpri;
-        if ((retVal = rtl8367c_setAsicVlanMemberConfig(empty_idx, &vlanMC)) != RT_ERR_OK)
-            return retVal;
-    }
-
-    /* Update Database */
-    vlan_mbrCfgUsage[empty_idx] = MBRCFG_USED_BY_VLAN;
-    vlan_mbrCfgVid[empty_idx] = vid;
-
-    *pIndex = empty_idx;
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_reservedVidAction_set
- * Description:
- *      Set Action of VLAN ID = 0 & 4095 tagged packet
- * Input:
- *      action_vid0     - Action for VID 0.
- *      action_vid4095  - Action for VID 4095.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_reservedVidAction_set(rtk_vlan_resVidAction_t action_vid0, rtk_vlan_resVidAction_t action_vid4095)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(action_vid0 >= RESVID_ACTION_END)
-        return RT_ERR_INPUT;
-
-    if(action_vid4095 >= RESVID_ACTION_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setReservedVidAction((rtk_uint32)action_vid0, (rtk_uint32)action_vid4095)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_reservedVidAction_get
- * Description:
- *      Get Action of VLAN ID = 0 & 4095 tagged packet
- * Input:
- *      pAction_vid0     - Action for VID 0.
- *      pAction_vid4095  - Action for VID 4095.
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_NULL_POINTER - NULL Pointer
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_reservedVidAction_get(rtk_vlan_resVidAction_t *pAction_vid0, rtk_vlan_resVidAction_t *pAction_vid4095)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(pAction_vid0 == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if(pAction_vid4095 == NULL)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getReservedVidAction((rtk_uint32 *)pAction_vid0, (rtk_uint32 *)pAction_vid4095)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_realKeepRemarkEnable_set
- * Description:
- *      Set Real keep 1p remarking feature
- * Input:
- *      enabled     - State of 1p remarking at real keep packet
- * Output:
- *      None.
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_realKeepRemarkEnable_set(rtk_enable_t enabled)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(enabled >= RTK_ENABLE_END)
-        return RT_ERR_INPUT;
-
-    if ((retVal = rtl8367c_setRealKeepRemarkEn((rtk_uint32)enabled)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_realKeepRemarkEnable_get
- * Description:
- *      Get Real keep 1p remarking feature
- * Input:
- *      None.
- * Output:
- *      pEnabled     - State of 1p remarking at real keep packet
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_realKeepRemarkEnable_get(rtk_enable_t *pEnabled)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if(NULL == pEnabled)
-        return RT_ERR_NULL_POINTER;
-
-    if ((retVal = rtl8367c_getRealKeepRemarkEn((rtk_uint32 *)pEnabled)) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
-/* Function Name:
- *      rtk_vlan_reset
- * Description:
- *      Reset VLAN
- * Input:
- *      None.
- * Output:
- *      pEnabled     - State of 1p remarking at real keep packet
- * Return:
- *      RT_ERR_OK           - OK
- *      RT_ERR_FAILED       - Failed
- *      RT_ERR_SMI          - SMI access error
- *      RT_ERR_INPUT        - Error Input
- * Note:
- *
- */
-rtk_api_ret_t rtk_vlan_reset(void)
-{
-    rtk_api_ret_t retVal;
-
-    /* Check initialization state */
-    RTK_CHK_INIT_STATE();
-
-    if ((retVal = rtl8367c_resetVlan()) != RT_ERR_OK)
-        return retVal;
-
-    return RT_ERR_OK;
-}
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s.c
deleted file mode 100644
index 6a55631d52..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s.c
+++ /dev/null
@@ -1,580 +0,0 @@
-/*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/skbuff.h>
-#include <linux/switch.h>
-
-//include from rtl8367c dir
-#include  "./rtl8367c/include/rtk_switch.h"
-#include  "./rtl8367c/include/vlan.h"
-#include  "./rtl8367c/include/stat.h"
-#include  "./rtl8367c/include/port.h"
-
-#define RTL8367C_SW_CPU_PORT    6
-
- //RTL8367C_PHY_PORT_NUM + ext0 + ext1
-#define RTL8367C_NUM_PORTS 7 
-#define RTL8367C_NUM_VIDS  4096   
-
-struct rtl8367_priv {
-	struct switch_dev	swdev;
-	bool			global_vlan_enable;
-};
-
-struct rtl8367_mib_counter {	
-	const char *name;
-};
-
-struct rtl8367_vlan_info {
-	unsigned short	vid;
-	unsigned int	untag;
-	unsigned int	member;
-	unsigned char		fid;
-};
-
-struct rtl8367_priv  rtl8367_priv_data;
-
-unsigned int rtl8367c_port_id[RTL8367C_NUM_PORTS]={0,1,2,3,4,EXT_PORT1,EXT_PORT0};
-
-void (*rtl8367_switch_reset_func)(void)=NULL;
-
-static  struct rtl8367_mib_counter  rtl8367c_mib_counters[] = {
-	{"ifInOctets"},
-	{"dot3StatsFCSErrors"},
-	{"dot3StatsSymbolErrors"},
-	{"dot3InPauseFrames"},
-	{"dot3ControlInUnknownOpcodes"},
-	{"etherStatsFragments"},
-	{"etherStatsJabbers"},
-	{"ifInUcastPkts"},
-	{"etherStatsDropEvents"},
-	{"etherStatsOctets"},
-	{"etherStatsUndersizePkts"},
-	{"etherStatsOversizePkts"},
-	{"etherStatsPkts64Octets"},
-	{"etherStatsPkts65to127Octets"},
-	{"etherStatsPkts128to255Octets"},
-	{"etherStatsPkts256to511Octets"},
-	{"etherStatsPkts512to1023Octets"},
-	{"etherStatsPkts1024toMaxOctets"},
-	{"etherStatsMcastPkts"}, 
-	{"etherStatsBcastPkts"},
-	{"ifOutOctets"},
-	{"dot3StatsSingleCollisionFrames"},
-	{"dot3StatsMultipleCollisionFrames"},
-	{"dot3StatsDeferredTransmissions"},
-	{"dot3StatsLateCollisions"}, 
-	{"etherStatsCollisions"},
-	{"dot3StatsExcessiveCollisions"},
-	{"dot3OutPauseFrames"},
-	{"dot1dBasePortDelayExceededDiscards"},
-	{"dot1dTpPortInDiscards"},
-	{"ifOutUcastPkts"},
-	{"ifOutMulticastPkts"},
-	{"ifOutBrocastPkts"},
-	{"outOampduPkts"},
-	{"inOampduPkts"},
-	{"pktgenPkts"},
-	{"inMldChecksumError"},
-	{"inIgmpChecksumError"},
-	{"inMldSpecificQuery"},
-	{"inMldGeneralQuery"},
-	{"inIgmpSpecificQuery"},
-	{"inIgmpGeneralQuery"},
-	{"inMldLeaves"},
-	{"inIgmpLeaves"},
-	{"inIgmpJoinsSuccess"},
-	{"inIgmpJoinsFail"},
-	{"inMldJoinsSuccess"},
-	{"inMldJoinsFail"},
-	{"inReportSuppressionDrop"},
-	{"inLeaveSuppressionDrop"},
-	{"outIgmpReports"},
-	{"outIgmpLeaves"},
-	{"outIgmpGeneralQuery"},
-	{"outIgmpSpecificQuery"},
-	{"outMldReports"},
-	{"outMldLeaves"},
-	{"outMldGeneralQuery"},
-	{"outMldSpecificQuery"},
-	{"inKnownMulticastPkts"},
-	{"ifInMulticastPkts"},
-	{"ifInBroadcastPkts"},
-	{"ifOutDiscards"}
-};
-
-/*rtl8367c  proprietary switch API wrapper */
-static inline unsigned int rtl8367c_sw_to_phy_port(int port)
-{
-	return rtl8367c_port_id[port];
-}
-
-static inline unsigned int rtl8367c_portmask_phy_to_sw(rtk_portmask_t phy_portmask)
-{
-	int i;
-	for (i = 0; i < RTL8367C_NUM_PORTS; i++) {
-		if(RTK_PORTMASK_IS_PORT_SET(phy_portmask,rtl8367c_sw_to_phy_port(i))) {
-			RTK_PORTMASK_PORT_CLEAR(phy_portmask,rtl8367c_sw_to_phy_port(i));
-			RTK_PORTMASK_PORT_SET(phy_portmask,i);
-		}		
-
-	}
-	return (unsigned int)phy_portmask.bits[0];
-}
-
-static int rtl8367c_reset_mibs(void)
-{
-	return rtk_stat_global_reset();
-}
-
-static int rtl8367c_reset_port_mibs(int port)
-{
-
-	return rtk_stat_port_reset(rtl8367c_sw_to_phy_port(port));
-}
-
-static int rtl8367c_get_mibs_num(void)
-{
-	return ARRAY_SIZE(rtl8367c_mib_counters);
-}
-
-static const char *rtl8367c_get_mib_name(int idx)
-{
-	
-	return rtl8367c_mib_counters[idx].name;
-}
-
-static int rtl8367c_get_port_mib_counter(int idx, int port, unsigned long long *counter)
-{
-	return rtk_stat_port_get(rtl8367c_sw_to_phy_port(port), idx, counter);
-}
-
-static int rtl8367c_is_vlan_valid(unsigned int vlan)
-{
-	unsigned max = RTL8367C_NUM_VIDS;	
-
-	if (vlan == 0 || vlan >= max)
-		return 0;
-
-	return 1;
-}
-
-static int rtl8367c_get_vlan( unsigned short vid, struct rtl8367_vlan_info *vlan)
-{	
-	rtk_vlan_cfg_t vlan_cfg;
-
-	memset(vlan, '\0', sizeof(struct rtl8367_vlan_info));
-
-	if (vid >= RTL8367C_NUM_VIDS)
-		return -EINVAL;	
-
-	if(rtk_vlan_get(vid,&vlan_cfg))
-       	return -EINVAL;		
-	
-	vlan->vid = vid;
-	vlan->member = rtl8367c_portmask_phy_to_sw(vlan_cfg.mbr);	
-	vlan->untag = rtl8367c_portmask_phy_to_sw(vlan_cfg.untag);	
-	vlan->fid = vlan_cfg.fid_msti;
-
-	return 0;
-}
-
-static int rtl8367c_set_vlan( unsigned short vid, u32 mbr, u32 untag, u8 fid)
-{	
-	rtk_vlan_cfg_t vlan_cfg;
-	int i;
-
-	memset(&vlan_cfg, 0x00, sizeof(rtk_vlan_cfg_t));	
-
-	for (i = 0; i < RTL8367C_NUM_PORTS; i++) {
-		if (mbr & (1 << i)) {
-			RTK_PORTMASK_PORT_SET(vlan_cfg.mbr, rtl8367c_sw_to_phy_port(i));
-			if(untag & (1 << i))
-				RTK_PORTMASK_PORT_SET(vlan_cfg.untag, rtl8367c_sw_to_phy_port(i));			
-		}
-	}
-	vlan_cfg.fid_msti=fid;
-	vlan_cfg.ivl_en = 1;
-	return rtk_vlan_set(vid, &vlan_cfg);
-}
-
-
-static int rtl8367c_get_pvid( int port, int *pvid)
-{
-	u32 prio=0;
-	
-	if (port >= RTL8367C_NUM_PORTS)
-		return -EINVAL;		
-
-	return rtk_vlan_portPvid_get(rtl8367c_sw_to_phy_port(port),pvid,&prio);
-}
-
-
-static int rtl8367c_set_pvid( int port, int pvid)
-{
-	u32 prio=0;
-	
-	if (port >= RTL8367C_NUM_PORTS)
-		return -EINVAL;		
-
-	return rtk_vlan_portPvid_set(rtl8367c_sw_to_phy_port(port),pvid,prio);
-}
-
-static int rtl8367c_get_port_link(int port, int *link, int *speed, int *duplex)
-{
-	
-	if(rtk_port_phyStatus_get(rtl8367c_sw_to_phy_port(port),(rtk_port_linkStatus_t *)link,
-					(rtk_port_speed_t *)speed,(rtk_port_duplex_t *)duplex))
-		return -EINVAL;
-
-	return 0;
-}
-
-/*common rtl8367 swconfig entry API*/
-
-static int
-rtl8367_sw_set_vlan_enable(struct switch_dev *dev,
-			   const struct switch_attr *attr,
-			   struct switch_val *val)
-{
-	struct rtl8367_priv *priv = container_of(dev, struct rtl8367_priv, swdev);	
-
-	priv->global_vlan_enable = val->value.i ;
-
-	return 0;
-}
-
-static int
-rtl8367_sw_get_vlan_enable(struct switch_dev *dev,
-			   const struct switch_attr *attr,
-			   struct switch_val *val)
-{
-	struct rtl8367_priv *priv = container_of(dev, struct rtl8367_priv, swdev);
-
-	val->value.i = priv->global_vlan_enable;
-
-	return 0;
-}
-
-static int rtl8367_sw_reset_mibs(struct switch_dev *dev,
-				  const struct switch_attr *attr,
-				  struct switch_val *val)
-{
-	return rtl8367c_reset_mibs();
-}
-
-
-static int rtl8367_sw_reset_port_mibs(struct switch_dev *dev,
-				       const struct switch_attr *attr,
-				       struct switch_val *val)
-{
-	int port;
-
-	port = val->port_vlan;
-	if (port >= RTL8367C_NUM_PORTS)
-		return -EINVAL;
-
-	return rtl8367c_reset_port_mibs(port);
-}
-
-static int rtl8367_sw_get_port_mib(struct switch_dev *dev,
-			    const struct switch_attr *attr,
-			    struct switch_val *val)
-{	
-	int i, len = 0;
-	unsigned long long counter = 0;
-	static char mib_buf[4096];
-
-	if (val->port_vlan >= RTL8367C_NUM_PORTS)
-		return -EINVAL;
-
-	len += snprintf(mib_buf + len, sizeof(mib_buf) - len,
-			"Port %d MIB counters\n",
-			val->port_vlan);	
-
-	for (i = 0; i <rtl8367c_get_mibs_num(); ++i) {
-		len += snprintf(mib_buf + len, sizeof(mib_buf) - len,
-				"%-36s: ",rtl8367c_get_mib_name(i));
-		if (!rtl8367c_get_port_mib_counter(i, val->port_vlan,
-					       &counter))
-			len += snprintf(mib_buf + len, sizeof(mib_buf) - len,
-					"%llu\n", counter);
-		else
-			len += snprintf(mib_buf + len, sizeof(mib_buf) - len,
-					"%s\n", "N/A");
-	}
-
-	val->value.s = mib_buf;
-	val->len = len;
-	return 0;
-}
-
-
-static int rtl8367_sw_get_vlan_info(struct switch_dev *dev,
-			     const struct switch_attr *attr,
-			     struct switch_val *val)
-{	
-	int i;
-	u32 len = 0;
-	struct rtl8367_vlan_info vlan;
-	static char vlan_buf[256];
-	int err;
-
-	if (!rtl8367c_is_vlan_valid(val->port_vlan))
-		return -EINVAL;
-
-	memset(vlan_buf, '\0', sizeof(vlan_buf));
-
-	err = rtl8367c_get_vlan(val->port_vlan, &vlan);
-	if (err)
-		return err;
-
-	len += snprintf(vlan_buf + len, sizeof(vlan_buf) - len,
-			"VLAN %d: Ports: '", vlan.vid);
-
-	for (i = 0; i <RTL8367C_NUM_PORTS; i++) {
-		if (!(vlan.member & (1 << i)))
-			continue;
-
-		len += snprintf(vlan_buf + len, sizeof(vlan_buf) - len, "%d%s", i,
-				(vlan.untag & (1 << i)) ? "" : "t");
-	}
-
-	len += snprintf(vlan_buf + len, sizeof(vlan_buf) - len,
-			"', members=%04x, untag=%04x, fid=%u",
-			vlan.member, vlan.untag, vlan.fid);
-
-	val->value.s = vlan_buf;
-	val->len = len;
-
-	return 0;
-}
-
-
-static int rtl8367_sw_get_vlan_ports(struct switch_dev *dev, struct switch_val *val)
-{
-	struct switch_port *port;
-	struct rtl8367_vlan_info vlan;
-	int i;	
-	
-	if (!rtl8367c_is_vlan_valid(val->port_vlan))
-		return -EINVAL;
-
-	if(rtl8367c_get_vlan(val->port_vlan, &vlan))
-		return -EINVAL;
-
-	port = &val->value.ports[0];
-	val->len = 0;
-	for (i = 0; i <RTL8367C_NUM_PORTS ; i++) {
-		if (!(vlan.member & BIT(i)))
-			continue;
-
-		port->id = i;
-		port->flags = (vlan.untag & BIT(i)) ?
-					0 : BIT(SWITCH_PORT_FLAG_TAGGED);
-		val->len++;
-		port++;
-	}
-	return 0;
-}
-
-
-static int rtl8367_sw_set_vlan_ports(struct switch_dev *dev, struct switch_val *val)
-{
-	struct switch_port *port;
-	u32 member = 0;
-	u32 untag = 0;
-	u8 fid=0;
-	int err;
-	int i;	
-	
-	if (!rtl8367c_is_vlan_valid(val->port_vlan))
-		return -EINVAL;
-
-	port = &val->value.ports[0];
-	for (i = 0; i < val->len; i++, port++) {
-		int pvid = 0;
-		member |= BIT(port->id);
-
-		if (!(port->flags & BIT(SWITCH_PORT_FLAG_TAGGED)))
-			untag |= BIT(port->id);
-
-		/*
-		 * To ensure that we have a valid MC entry for this VLAN,
-		 * initialize the port VLAN ID here.
-		 */
-		err = rtl8367c_get_pvid(port->id, &pvid);
-		if (err < 0)
-			return err;
-		if (pvid == 0) {
-			err = rtl8367c_set_pvid(port->id, val->port_vlan);
-			if (err < 0)
-				return err;
-		}
-	}
-
-	//pr_info("[%s] vid=%d , mem=%x,untag=%x,fid=%d \n",__func__,val->port_vlan,member,untag,fid);
-
-	return rtl8367c_set_vlan(val->port_vlan, member, untag, fid);	
-
-}
-
-
-static int rtl8367_sw_get_port_pvid(struct switch_dev *dev, int port, int *val)
-{
-	return rtl8367c_get_pvid(port, val);
-}
-
-
-static int rtl8367_sw_set_port_pvid(struct switch_dev *dev, int port, int val)
-{	
-	return rtl8367c_set_pvid(port, val);
-}
-
-
-static int rtl8367_sw_reset_switch(struct switch_dev *dev)
-{
-	if(rtl8367_switch_reset_func)
-		(*rtl8367_switch_reset_func)();
-	else
-		printk("rest switch is not supported\n");
-
-	return 0;
-}
-
-static int rtl8367_sw_get_port_link(struct switch_dev *dev, int port,
-				    struct switch_port_link *link)
-{	
-	int speed;
-
-	if (port >= RTL8367C_NUM_PORTS)
-		return -EINVAL;
-
-	if(rtl8367c_get_port_link(port,(int *)&link->link,(int *)&speed,(int *)&link->duplex))
-		return -EINVAL;		
-
-	if (!link->link)
-		return 0;	
-
-	switch (speed) {
-	case 0:
-		link->speed = SWITCH_PORT_SPEED_10;
-		break;
-	case 1:
-		link->speed = SWITCH_PORT_SPEED_100;
-		break;
-	case 2:
-		link->speed = SWITCH_PORT_SPEED_1000;
-		break;
-	default:
-		link->speed = SWITCH_PORT_SPEED_UNKNOWN;
-		break;
-	}
-
-	return 0;
-}
-
-
-static struct switch_attr rtl8367_globals[] = {
-	{
-		.type = SWITCH_TYPE_INT,
-		.name = "enable_vlan",
-		.description = "Enable VLAN mode",
-		.set = rtl8367_sw_set_vlan_enable,
-		.get = rtl8367_sw_get_vlan_enable,
-		.max = 1,		
-	}, {		
-		.type = SWITCH_TYPE_NOVAL,
-		.name = "reset_mibs",
-		.description = "Reset all MIB counters",
-		.set = rtl8367_sw_reset_mibs,
-	}
-};
-
-static struct switch_attr rtl8367_port[] = {
-	{
-		.type = SWITCH_TYPE_NOVAL,
-		.name = "reset_mib",
-		.description = "Reset single port MIB counters",
-		.set = rtl8367_sw_reset_port_mibs,
-	}, {
-		.type = SWITCH_TYPE_STRING,
-		.name = "mib",
-		.description = "Get MIB counters for port",
-		//.max = 33,
-		.set = NULL,
-		.get = rtl8367_sw_get_port_mib,
-	},
-};
-
-static struct switch_attr rtl8367_vlan[] = {
-	{
-		.type = SWITCH_TYPE_STRING,
-		.name = "info",
-		.description = "Get vlan information",
-		.max = 1,
-		.set = NULL,
-		.get = rtl8367_sw_get_vlan_info,
-	},
-};
-
-static const struct switch_dev_ops rtl8367_sw_ops = {
-	.attr_global = {
-		.attr = rtl8367_globals,
-		.n_attr = ARRAY_SIZE(rtl8367_globals),
-	},
-	.attr_port = {
-		.attr = rtl8367_port,
-		.n_attr = ARRAY_SIZE(rtl8367_port),
-	},
-	.attr_vlan = {
-		.attr = rtl8367_vlan,
-		.n_attr = ARRAY_SIZE(rtl8367_vlan),
-	},
-
-	.get_vlan_ports = rtl8367_sw_get_vlan_ports,
-	.set_vlan_ports = rtl8367_sw_set_vlan_ports,
-	.get_port_pvid = rtl8367_sw_get_port_pvid,
-	.set_port_pvid = rtl8367_sw_set_port_pvid,
-	.reset_switch = rtl8367_sw_reset_switch,
-	.get_port_link = rtl8367_sw_get_port_link,
-};
-
-int rtl8367s_swconfig_init(void (*reset_func)(void))
-{
-	struct rtl8367_priv  *priv = &rtl8367_priv_data;
-	struct switch_dev *dev=&priv->swdev;
-	int err=0;
-
-	rtl8367_switch_reset_func = reset_func ;
-	
-	memset(priv, 0, sizeof(struct rtl8367_priv));	
-	priv->global_vlan_enable =0;
-
-	dev->name = "RTL8367C";
-	dev->cpu_port = RTL8367C_SW_CPU_PORT;
-	dev->ports = RTL8367C_NUM_PORTS;
-	dev->vlans = RTL8367C_NUM_VIDS;
-	dev->ops = &rtl8367_sw_ops;
-	dev->alias = "RTL8367C";		
-	err = register_switch(dev, NULL);
-
-	pr_info("[%s]\n",__func__);
-
-	return err;
-}
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s_dbg.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s_dbg.c
deleted file mode 100644
index ec86679714..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s_dbg.c
+++ /dev/null
@@ -1,655 +0,0 @@
-#include <linux/uaccess.h>
-#include <linux/trace_seq.h>
-#include <linux/seq_file.h>
-#include <linux/proc_fs.h>
-#include <linux/u64_stats_sync.h>
-
-#include  "./rtl8367c/include/rtk_switch.h"
-#include  "./rtl8367c/include/port.h"
-#include  "./rtl8367c/include/vlan.h"
-#include  "./rtl8367c/include/rtl8367c_asicdrv_port.h"
-#include  "./rtl8367c/include/stat.h"
-#include  "./rtl8367c/include/l2.h"
-#include  "./rtl8367c/include/smi.h"
-#include  "./rtl8367c/include/mirror.h"
-#include  "./rtl8367c/include/igmp.h"
-#include  "./rtl8367c/include/leaky.h"
-
-static struct proc_dir_entry *proc_reg_dir;
-static struct proc_dir_entry *proc_esw_cnt;
-static struct proc_dir_entry *proc_vlan_cnt;
-static struct proc_dir_entry *proc_mac_tbl;
-static struct proc_dir_entry *proc_reg;
-static struct proc_dir_entry *proc_phyreg;
-static struct proc_dir_entry *proc_mirror;
-static struct proc_dir_entry *proc_igmp;
-
-#define PROCREG_ESW_CNT         "esw_cnt"
-#define PROCREG_VLAN            "vlan"
-#define PROCREG_MAC_TBL            "mac_tbl"
-#define PROCREG_REG            "reg"
-#define PROCREG_PHYREG            "phyreg"
-#define PROCREG_MIRROR            "mirror"
-#define PROCREG_IGMP            "igmp"
-#define PROCREG_DIR             "rtk_gsw"
-
-#define RTK_SW_VID_RANGE        16
-
-static void rtk_dump_mib_type(rtk_stat_port_type_t cntr_idx)
-{
-	rtk_port_t port;
-	rtk_stat_counter_t Cntr;
-
-	for (port = UTP_PORT0; port < (UTP_PORT0 + 5); port++) {
-		rtk_stat_port_get(port, cntr_idx, &Cntr);
-		printk("%8llu", Cntr);
-	}
-
-	for (port = EXT_PORT0; port < (EXT_PORT0 + 2); port++) {
-		rtk_stat_port_get(port, cntr_idx, &Cntr);
-		printk("%8llu", Cntr);
-	}
-	
-	printk("\n");
-}
-static void rtk_hal_dump_mib(void)
-{
-
-	printk("==================%8s%8s%8s%8s%8s%8s%8s\n", "Port0", "Port1",
-	       "Port2", "Port3", "Port4", "Port16", "Port17");
-	/* Get TX Unicast Pkts */
-	printk("TX Unicast Pkts  :");
-	rtk_dump_mib_type(STAT_IfOutUcastPkts);
-	/* Get TX Multicast Pkts */
-	printk("TX Multicast Pkts:");
-	rtk_dump_mib_type(STAT_IfOutMulticastPkts);
-	/* Get TX BroadCast Pkts */
-	printk("TX BroadCast Pkts:");
-	rtk_dump_mib_type(STAT_IfOutBroadcastPkts);
-	/* Get TX Collisions */
-	/* Get TX Puase Frames */
-	printk("TX Pause Frames  :");
-	rtk_dump_mib_type(STAT_Dot3OutPauseFrames);
-	/* Get TX Drop Events */
-	/* Get RX Unicast Pkts */
-	printk("RX Unicast Pkts  :");
-	rtk_dump_mib_type(STAT_IfInUcastPkts);
-	/* Get RX Multicast Pkts */
-	printk("RX Multicast Pkts:");
-	rtk_dump_mib_type(STAT_IfInMulticastPkts);
-	/* Get RX Broadcast Pkts */
-	printk("RX Broadcast Pkts:");
-	rtk_dump_mib_type(STAT_IfInBroadcastPkts);
-	/* Get RX FCS Erros */
-	printk("RX FCS Errors    :");
-	rtk_dump_mib_type(STAT_Dot3StatsFCSErrors);
-	/* Get RX Undersize Pkts */
-	printk("RX Undersize Pkts:");
-	rtk_dump_mib_type(STAT_EtherStatsUnderSizePkts);
-	/* Get RX Discard Pkts */
-	printk("RX Discard Pkts  :");
-	rtk_dump_mib_type(STAT_Dot1dTpPortInDiscards);
-	/* Get RX Fragments */
-	printk("RX Fragments     :");
-	rtk_dump_mib_type(STAT_EtherStatsFragments);
-	/* Get RX Oversize Pkts */
-	printk("RX Oversize Pkts :");
-	rtk_dump_mib_type(STAT_EtherOversizeStats);
-	/* Get RX Jabbers */
-	printk("RX Jabbers       :");
-	rtk_dump_mib_type(STAT_EtherStatsJabbers);
-	/* Get RX Pause Frames */
-	printk("RX Pause Frames  :");
-	rtk_dump_mib_type(STAT_Dot3InPauseFrames);
-	/* clear MIB */
-	rtk_stat_global_reset();
-	
-}
-
-static int rtk_hal_dump_vlan(void)
-{
-	rtk_vlan_cfg_t vlan;
-	int i;
-
-	printk("vid    portmap\n");
-	for (i = 0; i < RTK_SW_VID_RANGE; i++) {
-		rtk_vlan_get(i, &vlan);
-		printk("%3d    ", i);
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-	                                UTP_PORT0) ? '1' : '-');
-		printk("%c",
-	       	RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-	                                UTP_PORT1) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-	                                UTP_PORT2) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-	                                UTP_PORT3) ? '1' : '-');
-		printk("%c",
-	       	RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-	                                UTP_PORT4) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-	                                EXT_PORT0) ? '1' : '-');
-		printk("%c",
-		       RTK_PORTMASK_IS_PORT_SET(vlan.mbr,
-	                                EXT_PORT1) ? '1' : '-');
-		printk("\n");
-	}
-	
-	return 0;
-}
-
-static void rtk_hal_dump_table(void)
-{
-	rtk_uint32 i;
-	rtk_uint32 address = 0;
-	rtk_l2_ucastAddr_t l2_data;
-	rtk_l2_ipMcastAddr_t ipMcastAddr;
-	rtk_l2_age_time_t age_timout;
-
-	rtk_l2_aging_get(&age_timout);
-	printk("Mac table age timeout =%d\n",(unsigned int)age_timout);
-
-	printk("hash  port(0:17)   fid   vid  mac-address\n");
-	while (1) {
-		if (rtk_l2_addr_next_get(READMETHOD_NEXT_L2UC, UTP_PORT0, &address, &l2_data) != RT_ERR_OK) {
-			break;
-		} else {
-			printk("%03x   ", l2_data.address);
-			for (i = 0; i < 5; i++)
-				if ( l2_data.port == i)
-					printk("1");
-				else
-					printk("-");
-			for (i = 16; i < 18; i++)
-				if ( l2_data.port == i)
-					printk("1");
-				else
-					printk("-");
-
-			printk("      %2d", l2_data.fid);
-			printk("  %4d", l2_data.cvid);
-			printk("  %02x%02x%02x%02x%02x%02x\n", l2_data.mac.octet[0],
-			l2_data.mac.octet[1], l2_data.mac.octet[2], l2_data.mac.octet[3],
-			l2_data.mac.octet[4], l2_data.mac.octet[5]);
-			address ++;
-			}
-	}
-
-	address = 0;
-	while (1) {
-        if (rtk_l2_ipMcastAddr_next_get(&address, &ipMcastAddr) != RT_ERR_OK) {
-            break;
-        } else {
-            printk("%03x   ", ipMcastAddr.address);
-            for (i = 0; i < 5; i++)
-                printk("%c", RTK_PORTMASK_IS_PORT_SET(ipMcastAddr.portmask, i) ? '1' : '-');
-            for (i = 16; i < 18; i++)
-                printk("%c", RTK_PORTMASK_IS_PORT_SET(ipMcastAddr.portmask, i) ? '1' : '-');
-			printk("                ");
-			printk("01005E%06x\n", (ipMcastAddr.dip & 0xefffff));
-            address ++;
-            }
-    }
-}
-
-static void rtk_hal_clear_table(void)
-{
-        rtk_api_ret_t ret;
-
-        ret = rtk_l2_table_clear();
-        if (ret != RT_ERR_OK)
-                printk("rtk_l2_table_clear failed\n");
-}
-
-static void rtk_hal_read_reg(unsigned int reg_addr)
-{
-        ret_t retVal;
-	 unsigned int reg_val;
-
-        retVal = smi_read(reg_addr, &reg_val);
-
-        if(retVal != RT_ERR_OK)
-                printk("switch reg read failed\n");
-        else
-                printk("reg0x%x = 0x%x\n", reg_addr, reg_val);
-}
-
-static void rtk_hal_write_reg(unsigned int reg_addr , unsigned int reg_val)
-{
-        ret_t retVal;
-
-    retVal = smi_write(reg_addr, reg_val);
-
-    if(retVal != RT_ERR_OK)
-        printk("switch reg write failed\n");
-    else
-        printk("write switch reg0x%x 0x%x success\n", reg_addr, reg_val);
-}
-
-static void rtk_hal_get_phy_reg(unsigned int port ,unsigned int reg_addr )
-{
-        ret_t retVal;
-        rtk_port_phy_data_t Data;
-
-        retVal = rtk_port_phyReg_get(port, reg_addr, &Data);
-        if (retVal == RT_ERR_OK)
-                printk("Get: phy[%d].reg[%d] = 0x%04x\n", port, reg_addr, Data);
-        else
-                printk("read phy reg failed\n");
-}
-
-static void rtk_hal_set_phy_reg(unsigned int port ,unsigned int reg_addr,unsigned int reg_val)
-{
-        ret_t retVal;
-
-        retVal = rtk_port_phyReg_set(port, reg_addr, reg_val);
-        if (retVal == RT_ERR_OK)
-                printk("Set: phy[%d].reg[%d] = 0x%04x\n", port, reg_addr, reg_val);
-        else
-                printk("write phy reg failed\n");
-}
-
-static void rtk_hal_set_port_mirror(unsigned int port ,unsigned int rx_port_map,unsigned int tx_port_map)
-{
-        rtk_portmask_t rx_portmask;
-        rtk_portmask_t tx_portmask;
-        rtk_api_ret_t ret;
-        int i;
-
-        rtk_mirror_portIso_set(ENABLED);
-        RTK_PORTMASK_CLEAR(rx_portmask);
-        RTK_PORTMASK_CLEAR(tx_portmask);
-
-	for (i = 0; i < 5; i++)
-                if (rx_port_map & (1 << i))
-                        RTK_PORTMASK_PORT_SET(rx_portmask, i);
-
-        for (i = 0; i < 2; i++)
-                if (rx_port_map & (1 << (i + 5)))
-                        RTK_PORTMASK_PORT_SET(rx_portmask, (i + EXT_PORT0));
-
-        RTK_PORTMASK_CLEAR(tx_portmask);
-
-	for (i = 0; i < 5; i++)
-		if (tx_port_map & (1 << i))
-		           RTK_PORTMASK_PORT_SET(tx_portmask, i);
-
-	for (i = 0; i < 2; i++)
-		if (tx_port_map & (1 << (i + 5)))
-			RTK_PORTMASK_PORT_SET(tx_portmask, (i + EXT_PORT0));
-
-	ret = rtk_mirror_portBased_set(port, &rx_portmask, &tx_portmask);
-
-        if (!ret)
-                printk("rtk_mirror_portBased_set success\n");
-
-}
-
-static void rtk_hal_enable_igmpsnoop(int hw_on)
-{
-        rtk_api_ret_t ret;
-        rtk_portmask_t pmask;
-
-        ret = rtk_igmp_init();
-        if (hw_on == 1) {
-                RTK_PORTMASK_CLEAR(pmask);
-                RTK_PORTMASK_PORT_SET(pmask, EXT_PORT0);
-                ret |= rtk_igmp_static_router_port_set(&pmask);
-                ret |= rtk_igmp_protocol_set(UTP_PORT4, PROTOCOL_IGMPv1, IGMP_ACTION_FORWARD);
-                ret |= rtk_igmp_protocol_set(UTP_PORT4, PROTOCOL_IGMPv2, IGMP_ACTION_FORWARD);
-                ret |= rtk_igmp_protocol_set(UTP_PORT4, PROTOCOL_MLDv1, IGMP_ACTION_FORWARD);
-                ret |= rtk_igmp_protocol_set(EXT_PORT1, PROTOCOL_IGMPv1, IGMP_ACTION_FORWARD);
-                ret |= rtk_igmp_protocol_set(EXT_PORT1, PROTOCOL_IGMPv2, IGMP_ACTION_FORWARD);
-                ret |= rtk_igmp_protocol_set(EXT_PORT1, PROTOCOL_MLDv1, IGMP_ACTION_FORWARD);
-                ret |= rtk_igmp_protocol_set(UTP_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(UTP_PORT1, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(UTP_PORT2, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(UTP_PORT3, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(EXT_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-
-                ret |= rtk_leaky_vlan_set(LEAKY_IPMULTICAST, ENABLED);
-                ret |= rtk_l2_ipMcastForwardRouterPort_set(DISABLED);
-                /* drop unknown multicast packets*/
-                /* ret |= rtk_trap_unknownMcastPktAction_set(UTP_PORT4, MCAST_IPV4, MCAST_ACTION_DROP);*/
-        } else {
-		RTK_PORTMASK_CLEAR(pmask);
-		RTK_PORTMASK_PORT_SET(pmask, EXT_PORT0);
-		RTK_PORTMASK_PORT_SET(pmask, EXT_PORT1);
-                ret |= rtk_igmp_protocol_set(UTP_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(UTP_PORT1, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(UTP_PORT2, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(UTP_PORT3, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-                ret |= rtk_igmp_protocol_set(EXT_PORT0, PROTOCOL_IGMPv3, IGMP_ACTION_ASIC);
-
-                ret |= rtk_igmp_static_router_port_set(&pmask);
-        }
-
-        if(ret != RT_ERR_OK)
-                printk("enable switch igmpsnoop failed\n");
-
-}
-
-static void rtk_hal_disable_igmpsnoop(void)
-{
-        if (rtk_igmp_state_set(DISABLED) != RT_ERR_OK)
-                printk("Disable IGMP SNOOPING failed\n");
-}
-
-static ssize_t mac_tbl_write(struct file *file,
-                            const char __user *buffer, size_t count,
-                            loff_t *data)
-{
-	rtk_hal_clear_table();
-
-        return count;
-}
-
-
-static ssize_t phyreg_ops(struct file *file,
-                            const char __user *buffer, size_t count,
-                            loff_t *data)
-{
-        char buf[64];
-	 unsigned int port;
-        unsigned int offset;
-        unsigned int val;
-
-        memset(buf, 0, 64);
-
-        if (copy_from_user(buf, buffer, count))
-                return -EFAULT;
-
-
-        if(buf[0] == 'w') {
-
-                if(sscanf(buf, "w %d %x %x", &port,&offset,&val) == -1)
-                        return -EFAULT;
-                else
-                        rtk_hal_set_phy_reg(port,offset,val);
-
-        } else {
-
-		if(sscanf(buf, "r %d %x",&port, &offset) == -1)
-                        return -EFAULT;
-                else
-                        rtk_hal_get_phy_reg(port,offset);
-        }
-
-        return count;
-}
-
-static ssize_t reg_ops(struct file *file,
-                            const char __user *buffer, size_t count,
-                            loff_t *data)
-{
-        char buf[64];
-        unsigned int offset;
-        unsigned int val;
-
-        memset(buf, 0, 64);
-
-        if (copy_from_user(buf, buffer, count))
-                return -EFAULT;
-
-
-        if(buf[0] == 'w') {
-
-                if(sscanf(buf, "w %x %x", &offset,&val) == -1)
-                        return -EFAULT;
-                else
-                        rtk_hal_write_reg(offset,val);
-
-        } else {
-
-                if(sscanf(buf, "r %x", &offset) == -1)
-                        return -EFAULT;
-                else
-                        rtk_hal_read_reg(offset);
-        }
-
-        return count;
-}
-
-static ssize_t mirror_ops(struct file *file,
-                            const char __user *buffer, size_t count,
-                            loff_t *data)
-{
-        char buf[64];
-	 unsigned int port;
-        unsigned int tx_map,rx_map;
-
-        memset(buf, 0, 64);
-
-        if (copy_from_user(buf, buffer, count))
-                return -EFAULT;
-
-	if(sscanf(buf, "%d %x %x", &port,&rx_map,&tx_map) == -1)
-		return -EFAULT;
-	else
-		rtk_hal_set_port_mirror(port,rx_map,tx_map);
-
-        return count;
-}
-
-
-static ssize_t igmp_ops(struct file *file,
-                            const char __user *buffer, size_t count,
-                            loff_t *data)
-{
-        char buf[8];
-        unsigned int ops;
-
-        if (copy_from_user(buf, buffer, count))
-                return -EFAULT;
-
-	if(sscanf(buf, "%d", &ops) == -1)
-		return -EFAULT;
-
-        if(ops == 0)
-                rtk_hal_disable_igmpsnoop();
-	else if (ops == 1)
-		rtk_hal_enable_igmpsnoop(0);
-	else //hw igmp
-		rtk_hal_enable_igmpsnoop(1);
-
-        return count;
-}
-
-
-static int esw_cnt_read(struct seq_file *seq, void *v)
-{
-	rtk_hal_dump_mib();
-	return 0;
-}
-
-static int vlan_read(struct seq_file *seq, void *v)
-{
-	rtk_hal_dump_vlan();
-	return 0;
-}
-
-static int mac_tbl_read(struct seq_file *seq, void *v)
-{
-	rtk_hal_dump_table();
-	return 0;
-}
-
-static int reg_show(struct seq_file *seq, void *v)
-{
-	return 0;
-}
-
-static int phyreg_show(struct seq_file *seq, void *v)
-{
-	return 0;
-}
-
-static int mirror_show(struct seq_file *seq, void *v)
-{
-	return 0;
-}
-
-static int igmp_show(struct seq_file *seq, void *v)
-{
-	return 0;
-}
-
-static int switch_count_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, esw_cnt_read, 0);
-}
-
-static int switch_vlan_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, vlan_read, 0);
-}
-
-static int mac_tbl_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, mac_tbl_read, 0);
-}
-
-static int reg_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, reg_show, 0);
-}
-
-static int phyreg_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, phyreg_show, 0);
-}
-
-static int mirror_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, mirror_show, 0);
-}
-
-static int igmp_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, igmp_show, 0);
-}
-
-
-static const struct file_operations switch_count_fops = {
-	.owner = THIS_MODULE,
-	.open = switch_count_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release
-};
-
-static const struct file_operations switch_vlan_fops = {
-	.owner = THIS_MODULE,
-	.open = switch_vlan_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release
-};
-
-static const struct file_operations mac_tbl_fops = {
-        .owner = THIS_MODULE,
-        .open = mac_tbl_open,
-        .read = seq_read,
-        .llseek = seq_lseek,
-        .write = mac_tbl_write,
-        .release = single_release
-};
-
-static const struct file_operations reg_fops = {
-        .owner = THIS_MODULE,
-        .open = reg_open,
-        .read = seq_read,
-        .llseek = seq_lseek,
-        .write = reg_ops,
-        .release = single_release
-};
-
-static const struct file_operations phyreg_fops = {
-        .owner = THIS_MODULE,
-        .open = phyreg_open,
-        .read = seq_read,
-        .llseek = seq_lseek,
-        .write = phyreg_ops,
-        .release = single_release
-};
-
-static const struct file_operations mirror_fops = {
-        .owner = THIS_MODULE,
-        .open = mirror_open,
-        .read = seq_read,
-        .llseek = seq_lseek,
-        .write = mirror_ops,
-        .release = single_release
-};
-
-static const struct file_operations igmp_fops = {
-        .owner = THIS_MODULE,
-        .open = igmp_open,
-        .read = seq_read,
-        .llseek = seq_lseek,
-        .write = igmp_ops,
-        .release = single_release
-};
-
-int gsw_debug_proc_init(void)
-{
-
-	if (!proc_reg_dir)
-		proc_reg_dir = proc_mkdir(PROCREG_DIR, NULL);
-
-	proc_esw_cnt =
-	proc_create(PROCREG_ESW_CNT, 0, proc_reg_dir, &switch_count_fops);
-
-	if (!proc_esw_cnt)
-		pr_err("!! FAIL to create %s PROC !!\n", PROCREG_ESW_CNT);
-
-	proc_vlan_cnt =
-	proc_create(PROCREG_VLAN, 0, proc_reg_dir, &switch_vlan_fops);
-
-	if (!proc_vlan_cnt)
-		pr_err("!! FAIL to create %s PROC !!\n", PROCREG_VLAN);
-
-	proc_mac_tbl =
-	proc_create(PROCREG_MAC_TBL, 0, proc_reg_dir, &mac_tbl_fops);
-
-	if (!proc_mac_tbl)
-		pr_err("!! FAIL to create %s PROC !!\n", PROCREG_MAC_TBL);
-
-	proc_reg =
-	proc_create(PROCREG_REG, 0, proc_reg_dir, &reg_fops);
-
-	if (!proc_reg)
-		pr_err("!! FAIL to create %s PROC !!\n", PROCREG_REG);
-
-	proc_phyreg =
-	proc_create(PROCREG_PHYREG, 0, proc_reg_dir, &phyreg_fops);
-
-	if (!proc_phyreg)
-		pr_err("!! FAIL to create %s PROC !!\n", PROCREG_PHYREG);
-
-	proc_mirror =
-	proc_create(PROCREG_MIRROR, 0, proc_reg_dir, &mirror_fops);
-
-	if (!proc_mirror)
-		pr_err("!! FAIL to create %s PROC !!\n", PROCREG_MIRROR);
-
-	proc_igmp =
-	proc_create(PROCREG_IGMP, 0, proc_reg_dir, &igmp_fops);
-
-	if (!proc_igmp)
-		pr_err("!! FAIL to create %s PROC !!\n", PROCREG_IGMP);
-
-	return 0;
-}
-
-void gsw_debug_proc_exit(void)
-{
-	if (proc_esw_cnt)
-		remove_proc_entry(PROCREG_ESW_CNT, proc_reg_dir);
-}
-
-
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s_mdio.c b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s_mdio.c
deleted file mode 100644
index ae958e8967..0000000000
--- a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367s_mdio.c
+++ /dev/null
@@ -1,312 +0,0 @@
-/*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
- 
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/of_mdio.h>
-#include <linux/of_platform.h>
-#include <linux/of_gpio.h>
-
-
-#include  "./rtl8367c/include/rtk_switch.h"
-#include  "./rtl8367c/include/port.h"
-#include  "./rtl8367c/include/vlan.h"
-#include  "./rtl8367c/include/rtl8367c_asicdrv_port.h"
-
-struct rtk_gsw {
- 	struct device           *dev;
- 	struct mii_bus          *bus;
-	int reset_pin;
-};
-
-static struct rtk_gsw *_gsw;
-
-extern int gsw_debug_proc_init(void);
-extern void gsw_debug_proc_exit(void);
-
-#ifdef CONFIG_SWCONFIG
-extern int rtl8367s_swconfig_init( void (*reset_func)(void) );
-#endif
-
-/*mii_mgr_read/mii_mgr_write is the callback API for rtl8367 driver*/
-unsigned int mii_mgr_read(unsigned int phy_addr,unsigned int phy_register,unsigned int *read_data)
-{
-	struct mii_bus *bus = _gsw->bus;
-
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
-
-	*read_data = bus->read(bus, phy_addr, phy_register);
-
-	mutex_unlock(&bus->mdio_lock);
-
-	return 0;
-}
-
-unsigned int mii_mgr_write(unsigned int phy_addr,unsigned int phy_register,unsigned int write_data)
-{
-	struct mii_bus *bus =  _gsw->bus;
-
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
-
-	bus->write(bus, phy_addr, phy_register, write_data);
-
-	mutex_unlock(&bus->mdio_lock);
-	
-	return 0;
-}
-
-static int rtl8367s_hw_reset(void)
-{
-	struct rtk_gsw *gsw = _gsw;
-	int ret;
-
-	if (gsw->reset_pin < 0)
-		return 0;
-
-	ret = devm_gpio_request(gsw->dev, gsw->reset_pin, "mediatek,reset-pin");
-
-	if (ret)
-                printk("fail to devm_gpio_request\n");
-
-	gpio_direction_output(gsw->reset_pin, 0);
-
-	usleep_range(1000, 1100);
-
-	gpio_set_value(gsw->reset_pin, 1);
-
-	mdelay(500);
-
-	devm_gpio_free(gsw->dev, gsw->reset_pin);
-
-	return 0;
-	
-}
-
-static int rtl8367s_vlan_config(int want_at_p0)
-{
-	rtk_vlan_cfg_t vlan1, vlan2;
-	
-	/* Set LAN/WAN VLAN partition */
-	memset(&vlan1, 0x00, sizeof(rtk_vlan_cfg_t));
-
-	RTK_PORTMASK_PORT_SET(vlan1.mbr, EXT_PORT0);
-	RTK_PORTMASK_PORT_SET(vlan1.mbr, UTP_PORT1);
-	RTK_PORTMASK_PORT_SET(vlan1.mbr, UTP_PORT2);
-	RTK_PORTMASK_PORT_SET(vlan1.mbr, UTP_PORT3);
-	RTK_PORTMASK_PORT_SET(vlan1.untag, EXT_PORT0);
-	RTK_PORTMASK_PORT_SET(vlan1.untag, UTP_PORT1);
-	RTK_PORTMASK_PORT_SET(vlan1.untag, UTP_PORT2);
-	RTK_PORTMASK_PORT_SET(vlan1.untag, UTP_PORT3);
-  
-	 if (want_at_p0) {
-		RTK_PORTMASK_PORT_SET(vlan1.mbr, UTP_PORT4);
-		RTK_PORTMASK_PORT_SET(vlan1.untag, UTP_PORT4);
-        } else {
-		RTK_PORTMASK_PORT_SET(vlan1.mbr, UTP_PORT0);
-		RTK_PORTMASK_PORT_SET(vlan1.untag, UTP_PORT0);
-        }
-
-	vlan1.ivl_en = 1;
-	
-	rtk_vlan_set(1, &vlan1);
-	
-	memset(&vlan2, 0x00, sizeof(rtk_vlan_cfg_t));
-	
-	RTK_PORTMASK_PORT_SET(vlan2.mbr, EXT_PORT1);
-	RTK_PORTMASK_PORT_SET(vlan2.untag, EXT_PORT1);
-
-	if (want_at_p0) {
-		RTK_PORTMASK_PORT_SET(vlan2.mbr, UTP_PORT0);
-		RTK_PORTMASK_PORT_SET(vlan2.untag, UTP_PORT0);
-	} else {
-		RTK_PORTMASK_PORT_SET(vlan2.mbr, UTP_PORT4);
-		RTK_PORTMASK_PORT_SET(vlan2.untag, UTP_PORT4);
-	}
-
-	vlan2.ivl_en = 1;
-	rtk_vlan_set(2, &vlan2);
-
-	rtk_vlan_portPvid_set(EXT_PORT0, 1, 0);
-	rtk_vlan_portPvid_set(UTP_PORT1, 1, 0);
-	rtk_vlan_portPvid_set(UTP_PORT2, 1, 0);
-	rtk_vlan_portPvid_set(UTP_PORT3, 1, 0);
-	rtk_vlan_portPvid_set(EXT_PORT1, 2, 0);
-
-	if (want_at_p0) {
-		rtk_vlan_portPvid_set(UTP_PORT0, 2, 0);
-		rtk_vlan_portPvid_set(UTP_PORT4, 1, 0);
-	} else {
-		rtk_vlan_portPvid_set(UTP_PORT0, 1, 0);
-		rtk_vlan_portPvid_set(UTP_PORT4, 2, 0);
-	}
-
-	return 0;	
-}
-
-static int rtl8367s_hw_init(void)
-{
-
-	rtl8367s_hw_reset();
-
-	if(rtk_switch_init())
-	        return -1;
-
-	mdelay(500);
-
-	if (rtk_vlan_reset())
-	        return -1;
-
-	if (rtk_vlan_init())
-	        return -1;
-
-	return 0;
-}
-
-static void set_rtl8367s_sgmii(void)
-{
-	rtk_port_mac_ability_t mac_cfg;
-	rtk_mode_ext_t mode;
-
-	mode = MODE_EXT_HSGMII;
-	mac_cfg.forcemode = MAC_FORCE;
-	mac_cfg.speed = PORT_SPEED_2500M;
-	mac_cfg.duplex = PORT_FULL_DUPLEX;
-	mac_cfg.link = PORT_LINKUP;
-	mac_cfg.nway = DISABLED;
-	mac_cfg.txpause = ENABLED;
-	mac_cfg.rxpause = ENABLED;
-	rtk_port_macForceLinkExt_set(EXT_PORT0, mode, &mac_cfg);
-	rtk_port_sgmiiNway_set(EXT_PORT0, DISABLED);
-	rtk_port_phyEnableAll_set(ENABLED);
-
-}
-
-static void set_rtl8367s_rgmii(void)
-{
-	rtk_port_mac_ability_t mac_cfg;
-	rtk_mode_ext_t mode;
-
-	mode = MODE_EXT_RGMII;
-	mac_cfg.forcemode = MAC_FORCE;
-	mac_cfg.speed = PORT_SPEED_1000M;
-	mac_cfg.duplex = PORT_FULL_DUPLEX;
-	mac_cfg.link = PORT_LINKUP;
-	mac_cfg.nway = DISABLED;
-	mac_cfg.txpause = ENABLED;
-	mac_cfg.rxpause = ENABLED;
-	rtk_port_macForceLinkExt_set(EXT_PORT1, mode, &mac_cfg);
-	rtk_port_rgmiiDelayExt_set(EXT_PORT1, 1, 3);
-	rtk_port_phyEnableAll_set(ENABLED);
-	
-}
-
-void init_gsw(void)
-{
-	rtl8367s_hw_init();
-	set_rtl8367s_sgmii();
-	set_rtl8367s_rgmii();
-}
-
-// bleow are platform driver
-static const struct of_device_id rtk_gsw_match[] = {
-	{ .compatible = "mediatek,rtk-gsw" },
-	{},
-};
-
-MODULE_DEVICE_TABLE(of, rtk_gsw_match);
-
-static int rtk_gsw_probe(struct platform_device *pdev)
-{
-	struct device_node *np = pdev->dev.of_node;
-	struct device_node *mdio;
-	struct mii_bus *mdio_bus;
-	struct rtk_gsw *gsw;
-	const char *pm;
-
-	mdio = of_parse_phandle(np, "mediatek,mdio", 0);
-
-	if (!mdio)
-		return -EINVAL;
-
-	mdio_bus = of_mdio_find_bus(mdio);
-
-	if (!mdio_bus)
-		return -EPROBE_DEFER;
-
-	gsw = devm_kzalloc(&pdev->dev, sizeof(struct rtk_gsw), GFP_KERNEL);
-	
-	if (!gsw)
-		return -ENOMEM;	
-
-	gsw->dev = &pdev->dev;
-
-	gsw->bus = mdio_bus;
-
-	gsw->reset_pin = of_get_named_gpio(np, "mediatek,reset-pin", 0);
-
-	_gsw = gsw;
-
-	init_gsw();
-
-	//init default vlan or init swocnfig
-	if(!of_property_read_string(pdev->dev.of_node,
-						"mediatek,port_map", &pm)) {
-
-		if (!strcasecmp(pm, "wllll"))
-			rtl8367s_vlan_config(1); 
-		else
-			rtl8367s_vlan_config(0);
-		
-		} else {
-#ifdef CONFIG_SWCONFIG		
-		rtl8367s_swconfig_init(&init_gsw);
-#else
-		rtl8367s_vlan_config(0);
-#endif
-	}
-
-	gsw_debug_proc_init();
-
-	platform_set_drvdata(pdev, gsw);
-
-	return 0;
-	
-}
-
-static int rtk_gsw_remove(struct platform_device *pdev)
-{
-	platform_set_drvdata(pdev, NULL);
-	gsw_debug_proc_exit();
-
-	return 0;
-}
-
-static struct platform_driver gsw_driver = {
-	.probe = rtk_gsw_probe,
-	.remove = rtk_gsw_remove,
-	.driver = {
-		.name = "rtk-gsw",
-		.owner = THIS_MODULE,
-		.of_match_table = rtk_gsw_match,
-	},
-};
-
-module_platform_driver(gsw_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Mark Lee <marklee0201@gmail.com>");
-MODULE_DESCRIPTION("rtl8367c switch driver for MT7622");
-
diff --git a/target/linux/mediatek/patches-5.4/0001-v5.7-spi-make-spi-max-frequency-optional.patch b/target/linux/mediatek/patches-5.4/0001-v5.7-spi-make-spi-max-frequency-optional.patch
deleted file mode 100644
index 79ce15c37b..0000000000
--- a/target/linux/mediatek/patches-5.4/0001-v5.7-spi-make-spi-max-frequency-optional.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From 671c3bf50ae498dc12aef6c70abe5cfa066b1348 Mon Sep 17 00:00:00 2001
-From: Chuanhong Guo <gch981213@gmail.com>
-Date: Fri, 6 Mar 2020 16:50:49 +0800
-Subject: [PATCH 1/2] spi: make spi-max-frequency optional
-
-We only need a spi-max-frequency when we specifically request a
-spi frequency lower than the max speed of spi host.
-This property is already documented as optional property and current
-host drivers are implemented to operate at highest speed possible
-when spi->max_speed_hz is 0.
-This patch makes spi-max-frequency an optional property so that
-we could just omit it to use max controller speed.
-
-Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
-Link: https://lore.kernel.org/r/20200306085052.28258-2-gch981213@gmail.com
-Signed-off-by: Mark Brown <broonie@kernel.org>
----
- drivers/spi/spi.c | 9 ++-------
- 1 file changed, 2 insertions(+), 7 deletions(-)
-
---- a/drivers/spi/spi.c
-+++ b/drivers/spi/spi.c
-@@ -1809,13 +1809,8 @@ static int of_spi_parse_dt(struct spi_co
- 		spi->mode |= SPI_CS_HIGH;
- 
- 	/* Device speed */
--	rc = of_property_read_u32(nc, "spi-max-frequency", &value);
--	if (rc) {
--		dev_err(&ctlr->dev,
--			"%pOF has no valid 'spi-max-frequency' property (%d)\n", nc, rc);
--		return rc;
--	}
--	spi->max_speed_hz = value;
-+	if (!of_property_read_u32(nc, "spi-max-frequency", &value))
-+		spi->max_speed_hz = value;
- 
- 	return 0;
- }
diff --git a/target/linux/mediatek/patches-5.4/0002-v5.7-spi-add-support-for-mediatek-spi-nor-controller.patch b/target/linux/mediatek/patches-5.4/0002-v5.7-spi-add-support-for-mediatek-spi-nor-controller.patch
deleted file mode 100644
index 0a63bdddaf..0000000000
--- a/target/linux/mediatek/patches-5.4/0002-v5.7-spi-add-support-for-mediatek-spi-nor-controller.patch
+++ /dev/null
@@ -1,761 +0,0 @@
-From 881d1ee9fe81ff2be1b90809a07621be97404a57 Mon Sep 17 00:00:00 2001
-From: Chuanhong Guo <gch981213@gmail.com>
-Date: Fri, 6 Mar 2020 16:50:50 +0800
-Subject: [PATCH 2/2] spi: add support for mediatek spi-nor controller
-
-This is a driver for mtk spi-nor controller using spi-mem interface.
-The same controller already has limited support provided by mtk-quadspi
-driver under spi-nor framework and this new driver is a replacement
-for the old one.
-
-Comparing to the old driver, this driver has following advantages:
-1. It can handle any full-duplex spi transfer up to 6 bytes, and
-   this is implemented using generic spi interface.
-2. It take account into command opcode properly. The reading routine
-   in this controller can only use 0x03 or 0x0b as opcode on 1-1-1
-   transfers, but old driver doesn't implement this properly. This
-   driver checks supported opcode explicitly and use (1) to perform
-   unmatched operations.
-3. It properly handles SFDP reading. Old driver can't read SFDP
-   due to the bug mentioned in (2).
-4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops
-   requires parsing SFDP, which isn't possible in old driver. And
-   the old driver is only flagged to support 1-1-2 mode.
-5. It takes advantage of the DMA feature in this controller for
-   long reads and supports IRQ on DMA requests to free cpu cycles
-   from polling status registers on long DMA reading. It achieves
-   up to 17.5MB/s reading speed (1-4-4 mode) which is way faster
-   than the old one. IRQ is implemented as optional to maintain
-   backward compatibility.
-
-Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
-Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com
-Signed-off-by: Mark Brown <broonie@kernel.org>
----
- drivers/spi/Kconfig       |  10 +
- drivers/spi/Makefile      |   1 +
- drivers/spi/spi-mtk-nor.c | 689 ++++++++++++++++++++++++++++++++++++++
- 3 files changed, 700 insertions(+)
- create mode 100644 drivers/spi/spi-mtk-nor.c
-
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -433,6 +433,16 @@ config SPI_MT7621
- 	help
- 	  This selects a driver for the MediaTek MT7621 SPI Controller.
- 
-+config SPI_MTK_NOR
-+	tristate "MediaTek SPI NOR controller"
-+	depends on ARCH_MEDIATEK || COMPILE_TEST
-+	help
-+	  This enables support for SPI NOR controller found on MediaTek
-+	  ARM SoCs. This is a controller specifically for SPI-NOR flash.
-+	  It can perform generic SPI transfers up to 6 bytes via generic
-+	  SPI interface as well as several SPI-NOR specific instructions
-+	  via SPI MEM interface.
-+
- config SPI_NPCM_FIU
- 	tristate "Nuvoton NPCM FLASH Interface Unit"
- 	depends on ARCH_NPCM || COMPILE_TEST
---- a/drivers/spi/Makefile
-+++ b/drivers/spi/Makefile
-@@ -61,6 +61,7 @@ obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mp
- obj-$(CONFIG_SPI_MPC52xx)		+= spi-mpc52xx.o
- obj-$(CONFIG_SPI_MT65XX)                += spi-mt65xx.o
- obj-$(CONFIG_SPI_MT7621)		+= spi-mt7621.o
-+obj-$(CONFIG_SPI_MTK_NOR)		+= spi-mtk-nor.o
- obj-$(CONFIG_SPI_MXIC)			+= spi-mxic.o
- obj-$(CONFIG_SPI_MXS)			+= spi-mxs.o
- obj-$(CONFIG_SPI_NPCM_FIU)		+= spi-npcm-fiu.o
---- /dev/null
-+++ b/drivers/spi/spi-mtk-nor.c
-@@ -0,0 +1,689 @@
-+// SPDX-License-Identifier: GPL-2.0
-+//
-+// Mediatek SPI NOR controller driver
-+//
-+// Copyright (C) 2020 Chuanhong Guo <gch981213@gmail.com>
-+
-+#include <linux/bits.h>
-+#include <linux/clk.h>
-+#include <linux/completion.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/interrupt.h>
-+#include <linux/io.h>
-+#include <linux/iopoll.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of_device.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/spi-mem.h>
-+#include <linux/string.h>
-+
-+#define DRIVER_NAME "mtk-spi-nor"
-+
-+#define MTK_NOR_REG_CMD			0x00
-+#define MTK_NOR_CMD_WRITE		BIT(4)
-+#define MTK_NOR_CMD_PROGRAM		BIT(2)
-+#define MTK_NOR_CMD_READ		BIT(0)
-+#define MTK_NOR_CMD_MASK		GENMASK(5, 0)
-+
-+#define MTK_NOR_REG_PRG_CNT		0x04
-+#define MTK_NOR_REG_RDATA		0x0c
-+
-+#define MTK_NOR_REG_RADR0		0x10
-+#define MTK_NOR_REG_RADR(n)		(MTK_NOR_REG_RADR0 + 4 * (n))
-+#define MTK_NOR_REG_RADR3		0xc8
-+
-+#define MTK_NOR_REG_WDATA		0x1c
-+
-+#define MTK_NOR_REG_PRGDATA0		0x20
-+#define MTK_NOR_REG_PRGDATA(n)		(MTK_NOR_REG_PRGDATA0 + 4 * (n))
-+#define MTK_NOR_REG_PRGDATA_MAX		5
-+
-+#define MTK_NOR_REG_SHIFT0		0x38
-+#define MTK_NOR_REG_SHIFT(n)		(MTK_NOR_REG_SHIFT0 + 4 * (n))
-+#define MTK_NOR_REG_SHIFT_MAX		9
-+
-+#define MTK_NOR_REG_CFG1		0x60
-+#define MTK_NOR_FAST_READ		BIT(0)
-+
-+#define MTK_NOR_REG_CFG2		0x64
-+#define MTK_NOR_WR_CUSTOM_OP_EN		BIT(4)
-+#define MTK_NOR_WR_BUF_EN		BIT(0)
-+
-+#define MTK_NOR_REG_PP_DATA		0x98
-+
-+#define MTK_NOR_REG_IRQ_STAT		0xa8
-+#define MTK_NOR_REG_IRQ_EN		0xac
-+#define MTK_NOR_IRQ_DMA			BIT(7)
-+#define MTK_NOR_IRQ_MASK		GENMASK(7, 0)
-+
-+#define MTK_NOR_REG_CFG3		0xb4
-+#define MTK_NOR_DISABLE_WREN		BIT(7)
-+#define MTK_NOR_DISABLE_SR_POLL		BIT(5)
-+
-+#define MTK_NOR_REG_WP			0xc4
-+#define MTK_NOR_ENABLE_SF_CMD		0x30
-+
-+#define MTK_NOR_REG_BUSCFG		0xcc
-+#define MTK_NOR_4B_ADDR			BIT(4)
-+#define MTK_NOR_QUAD_ADDR		BIT(3)
-+#define MTK_NOR_QUAD_READ		BIT(2)
-+#define MTK_NOR_DUAL_ADDR		BIT(1)
-+#define MTK_NOR_DUAL_READ		BIT(0)
-+#define MTK_NOR_BUS_MODE_MASK		GENMASK(4, 0)
-+
-+#define MTK_NOR_REG_DMA_CTL		0x718
-+#define MTK_NOR_DMA_START		BIT(0)
-+
-+#define MTK_NOR_REG_DMA_FADR		0x71c
-+#define MTK_NOR_REG_DMA_DADR		0x720
-+#define MTK_NOR_REG_DMA_END_DADR	0x724
-+
-+#define MTK_NOR_PRG_MAX_SIZE		6
-+// Reading DMA src/dst addresses have to be 16-byte aligned
-+#define MTK_NOR_DMA_ALIGN		16
-+#define MTK_NOR_DMA_ALIGN_MASK		(MTK_NOR_DMA_ALIGN - 1)
-+// and we allocate a bounce buffer if destination address isn't aligned.
-+#define MTK_NOR_BOUNCE_BUF_SIZE		PAGE_SIZE
-+
-+// Buffered page program can do one 128-byte transfer
-+#define MTK_NOR_PP_SIZE			128
-+
-+#define CLK_TO_US(sp, clkcnt)		((clkcnt) * 1000000 / sp->spi_freq)
-+
-+struct mtk_nor {
-+	struct spi_controller *ctlr;
-+	struct device *dev;
-+	void __iomem *base;
-+	u8 *buffer;
-+	struct clk *spi_clk;
-+	struct clk *ctlr_clk;
-+	unsigned int spi_freq;
-+	bool wbuf_en;
-+	bool has_irq;
-+	struct completion op_done;
-+};
-+
-+static inline void mtk_nor_rmw(struct mtk_nor *sp, u32 reg, u32 set, u32 clr)
-+{
-+	u32 val = readl(sp->base + reg);
-+
-+	val &= ~clr;
-+	val |= set;
-+	writel(val, sp->base + reg);
-+}
-+
-+static inline int mtk_nor_cmd_exec(struct mtk_nor *sp, u32 cmd, ulong clk)
-+{
-+	ulong delay = CLK_TO_US(sp, clk);
-+	u32 reg;
-+	int ret;
-+
-+	writel(cmd, sp->base + MTK_NOR_REG_CMD);
-+	ret = readl_poll_timeout(sp->base + MTK_NOR_REG_CMD, reg, !(reg & cmd),
-+				 delay / 3, (delay + 1) * 200);
-+	if (ret < 0)
-+		dev_err(sp->dev, "command %u timeout.\n", cmd);
-+	return ret;
-+}
-+
-+static void mtk_nor_set_addr(struct mtk_nor *sp, const struct spi_mem_op *op)
-+{
-+	u32 addr = op->addr.val;
-+	int i;
-+
-+	for (i = 0; i < 3; i++) {
-+		writeb(addr & 0xff, sp->base + MTK_NOR_REG_RADR(i));
-+		addr >>= 8;
-+	}
-+	if (op->addr.nbytes == 4) {
-+		writeb(addr & 0xff, sp->base + MTK_NOR_REG_RADR3);
-+		mtk_nor_rmw(sp, MTK_NOR_REG_BUSCFG, MTK_NOR_4B_ADDR, 0);
-+	} else {
-+		mtk_nor_rmw(sp, MTK_NOR_REG_BUSCFG, 0, MTK_NOR_4B_ADDR);
-+	}
-+}
-+
-+static bool mtk_nor_match_read(const struct spi_mem_op *op)
-+{
-+	int dummy = 0;
-+
-+	if (op->dummy.buswidth)
-+		dummy = op->dummy.nbytes * BITS_PER_BYTE / op->dummy.buswidth;
-+
-+	if ((op->data.buswidth == 2) || (op->data.buswidth == 4)) {
-+		if (op->addr.buswidth == 1)
-+			return dummy == 8;
-+		else if (op->addr.buswidth == 2)
-+			return dummy == 4;
-+		else if (op->addr.buswidth == 4)
-+			return dummy == 6;
-+	} else if ((op->addr.buswidth == 1) && (op->data.buswidth == 1)) {
-+		if (op->cmd.opcode == 0x03)
-+			return dummy == 0;
-+		else if (op->cmd.opcode == 0x0b)
-+			return dummy == 8;
-+	}
-+	return false;
-+}
-+
-+static int mtk_nor_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
-+{
-+	size_t len;
-+
-+	if (!op->data.nbytes)
-+		return 0;
-+
-+	if ((op->addr.nbytes == 3) || (op->addr.nbytes == 4)) {
-+		if ((op->data.dir == SPI_MEM_DATA_IN) &&
-+		    mtk_nor_match_read(op)) {
-+			if ((op->addr.val & MTK_NOR_DMA_ALIGN_MASK) ||
-+			    (op->data.nbytes < MTK_NOR_DMA_ALIGN))
-+				op->data.nbytes = 1;
-+			else if (!((ulong)(op->data.buf.in) &
-+				   MTK_NOR_DMA_ALIGN_MASK))
-+				op->data.nbytes &= ~MTK_NOR_DMA_ALIGN_MASK;
-+			else if (op->data.nbytes > MTK_NOR_BOUNCE_BUF_SIZE)
-+				op->data.nbytes = MTK_NOR_BOUNCE_BUF_SIZE;
-+			return 0;
-+		} else if (op->data.dir == SPI_MEM_DATA_OUT) {
-+			if (op->data.nbytes >= MTK_NOR_PP_SIZE)
-+				op->data.nbytes = MTK_NOR_PP_SIZE;
-+			else
-+				op->data.nbytes = 1;
-+			return 0;
-+		}
-+	}
-+
-+	len = MTK_NOR_PRG_MAX_SIZE - sizeof(op->cmd.opcode) - op->addr.nbytes -
-+	      op->dummy.nbytes;
-+	if (op->data.nbytes > len)
-+		op->data.nbytes = len;
-+
-+	return 0;
-+}
-+
-+static bool mtk_nor_supports_op(struct spi_mem *mem,
-+				const struct spi_mem_op *op)
-+{
-+	size_t len;
-+
-+	if (op->cmd.buswidth != 1)
-+		return false;
-+
-+	if ((op->addr.nbytes == 3) || (op->addr.nbytes == 4)) {
-+		if ((op->data.dir == SPI_MEM_DATA_IN) && mtk_nor_match_read(op))
-+			return true;
-+		else if (op->data.dir == SPI_MEM_DATA_OUT)
-+			return (op->addr.buswidth == 1) &&
-+			       (op->dummy.buswidth == 0) &&
-+			       (op->data.buswidth == 1);
-+	}
-+	len = sizeof(op->cmd.opcode) + op->addr.nbytes + op->dummy.nbytes;
-+	if ((len > MTK_NOR_PRG_MAX_SIZE) ||
-+	    ((op->data.nbytes) && (len == MTK_NOR_PRG_MAX_SIZE)))
-+		return false;
-+	return true;
-+}
-+
-+static void mtk_nor_setup_bus(struct mtk_nor *sp, const struct spi_mem_op *op)
-+{
-+	u32 reg = 0;
-+
-+	if (op->addr.nbytes == 4)
-+		reg |= MTK_NOR_4B_ADDR;
-+
-+	if (op->data.buswidth == 4) {
-+		reg |= MTK_NOR_QUAD_READ;
-+		writeb(op->cmd.opcode, sp->base + MTK_NOR_REG_PRGDATA(4));
-+		if (op->addr.buswidth == 4)
-+			reg |= MTK_NOR_QUAD_ADDR;
-+	} else if (op->data.buswidth == 2) {
-+		reg |= MTK_NOR_DUAL_READ;
-+		writeb(op->cmd.opcode, sp->base + MTK_NOR_REG_PRGDATA(3));
-+		if (op->addr.buswidth == 2)
-+			reg |= MTK_NOR_DUAL_ADDR;
-+	} else {
-+		if (op->cmd.opcode == 0x0b)
-+			mtk_nor_rmw(sp, MTK_NOR_REG_CFG1, MTK_NOR_FAST_READ, 0);
-+		else
-+			mtk_nor_rmw(sp, MTK_NOR_REG_CFG1, 0, MTK_NOR_FAST_READ);
-+	}
-+	mtk_nor_rmw(sp, MTK_NOR_REG_BUSCFG, reg, MTK_NOR_BUS_MODE_MASK);
-+}
-+
-+static int mtk_nor_read_dma(struct mtk_nor *sp, u32 from, unsigned int length,
-+			    u8 *buffer)
-+{
-+	int ret = 0;
-+	ulong delay;
-+	u32 reg;
-+	dma_addr_t dma_addr;
-+
-+	dma_addr = dma_map_single(sp->dev, buffer, length, DMA_FROM_DEVICE);
-+	if (dma_mapping_error(sp->dev, dma_addr)) {
-+		dev_err(sp->dev, "failed to map dma buffer.\n");
-+		return -EINVAL;
-+	}
-+
-+	writel(from, sp->base + MTK_NOR_REG_DMA_FADR);
-+	writel(dma_addr, sp->base + MTK_NOR_REG_DMA_DADR);
-+	writel(dma_addr + length, sp->base + MTK_NOR_REG_DMA_END_DADR);
-+
-+	if (sp->has_irq) {
-+		reinit_completion(&sp->op_done);
-+		mtk_nor_rmw(sp, MTK_NOR_REG_IRQ_EN, MTK_NOR_IRQ_DMA, 0);
-+	}
-+
-+	mtk_nor_rmw(sp, MTK_NOR_REG_DMA_CTL, MTK_NOR_DMA_START, 0);
-+
-+	delay = CLK_TO_US(sp, (length + 5) * BITS_PER_BYTE);
-+
-+	if (sp->has_irq) {
-+		if (!wait_for_completion_timeout(&sp->op_done,
-+						 (delay + 1) * 100))
-+			ret = -ETIMEDOUT;
-+	} else {
-+		ret = readl_poll_timeout(sp->base + MTK_NOR_REG_DMA_CTL, reg,
-+					 !(reg & MTK_NOR_DMA_START), delay / 3,
-+					 (delay + 1) * 100);
-+	}
-+
-+	dma_unmap_single(sp->dev, dma_addr, length, DMA_FROM_DEVICE);
-+	if (ret < 0)
-+		dev_err(sp->dev, "dma read timeout.\n");
-+
-+	return ret;
-+}
-+
-+static int mtk_nor_read_bounce(struct mtk_nor *sp, u32 from,
-+			       unsigned int length, u8 *buffer)
-+{
-+	unsigned int rdlen;
-+	int ret;
-+
-+	if (length & MTK_NOR_DMA_ALIGN_MASK)
-+		rdlen = (length + MTK_NOR_DMA_ALIGN) & ~MTK_NOR_DMA_ALIGN_MASK;
-+	else
-+		rdlen = length;
-+
-+	ret = mtk_nor_read_dma(sp, from, rdlen, sp->buffer);
-+	if (ret)
-+		return ret;
-+
-+	memcpy(buffer, sp->buffer, length);
-+	return 0;
-+}
-+
-+static int mtk_nor_read_pio(struct mtk_nor *sp, const struct spi_mem_op *op)
-+{
-+	u8 *buf = op->data.buf.in;
-+	int ret;
-+
-+	ret = mtk_nor_cmd_exec(sp, MTK_NOR_CMD_READ, 6 * BITS_PER_BYTE);
-+	if (!ret)
-+		buf[0] = readb(sp->base + MTK_NOR_REG_RDATA);
-+	return ret;
-+}
-+
-+static int mtk_nor_write_buffer_enable(struct mtk_nor *sp)
-+{
-+	int ret;
-+	u32 val;
-+
-+	if (sp->wbuf_en)
-+		return 0;
-+
-+	val = readl(sp->base + MTK_NOR_REG_CFG2);
-+	writel(val | MTK_NOR_WR_BUF_EN, sp->base + MTK_NOR_REG_CFG2);
-+	ret = readl_poll_timeout(sp->base + MTK_NOR_REG_CFG2, val,
-+				 val & MTK_NOR_WR_BUF_EN, 0, 10000);
-+	if (!ret)
-+		sp->wbuf_en = true;
-+	return ret;
-+}
-+
-+static int mtk_nor_write_buffer_disable(struct mtk_nor *sp)
-+{
-+	int ret;
-+	u32 val;
-+
-+	if (!sp->wbuf_en)
-+		return 0;
-+	val = readl(sp->base + MTK_NOR_REG_CFG2);
-+	writel(val & ~MTK_NOR_WR_BUF_EN, sp->base + MTK_NOR_REG_CFG2);
-+	ret = readl_poll_timeout(sp->base + MTK_NOR_REG_CFG2, val,
-+				 !(val & MTK_NOR_WR_BUF_EN), 0, 10000);
-+	if (!ret)
-+		sp->wbuf_en = false;
-+	return ret;
-+}
-+
-+static int mtk_nor_pp_buffered(struct mtk_nor *sp, const struct spi_mem_op *op)
-+{
-+	const u8 *buf = op->data.buf.out;
-+	u32 val;
-+	int ret, i;
-+
-+	ret = mtk_nor_write_buffer_enable(sp);
-+	if (ret < 0)
-+		return ret;
-+
-+	for (i = 0; i < op->data.nbytes; i += 4) {
-+		val = buf[i + 3] << 24 | buf[i + 2] << 16 | buf[i + 1] << 8 |
-+		      buf[i];
-+		writel(val, sp->base + MTK_NOR_REG_PP_DATA);
-+	}
-+	return mtk_nor_cmd_exec(sp, MTK_NOR_CMD_WRITE,
-+				(op->data.nbytes + 5) * BITS_PER_BYTE);
-+}
-+
-+static int mtk_nor_pp_unbuffered(struct mtk_nor *sp,
-+				 const struct spi_mem_op *op)
-+{
-+	const u8 *buf = op->data.buf.out;
-+	int ret;
-+
-+	ret = mtk_nor_write_buffer_disable(sp);
-+	if (ret < 0)
-+		return ret;
-+	writeb(buf[0], sp->base + MTK_NOR_REG_WDATA);
-+	return mtk_nor_cmd_exec(sp, MTK_NOR_CMD_WRITE, 6 * BITS_PER_BYTE);
-+}
-+
-+int mtk_nor_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
-+{
-+	struct mtk_nor *sp = spi_controller_get_devdata(mem->spi->master);
-+	int ret;
-+
-+	if ((op->data.nbytes == 0) ||
-+	    ((op->addr.nbytes != 3) && (op->addr.nbytes != 4)))
-+		return -ENOTSUPP;
-+
-+	if (op->data.dir == SPI_MEM_DATA_OUT) {
-+		mtk_nor_set_addr(sp, op);
-+		writeb(op->cmd.opcode, sp->base + MTK_NOR_REG_PRGDATA0);
-+		if (op->data.nbytes == MTK_NOR_PP_SIZE)
-+			return mtk_nor_pp_buffered(sp, op);
-+		return mtk_nor_pp_unbuffered(sp, op);
-+	}
-+
-+	if ((op->data.dir == SPI_MEM_DATA_IN) && mtk_nor_match_read(op)) {
-+		ret = mtk_nor_write_buffer_disable(sp);
-+		if (ret < 0)
-+			return ret;
-+		mtk_nor_setup_bus(sp, op);
-+		if (op->data.nbytes == 1) {
-+			mtk_nor_set_addr(sp, op);
-+			return mtk_nor_read_pio(sp, op);
-+		} else if (((ulong)(op->data.buf.in) &
-+			    MTK_NOR_DMA_ALIGN_MASK)) {
-+			return mtk_nor_read_bounce(sp, op->addr.val,
-+						   op->data.nbytes,
-+						   op->data.buf.in);
-+		} else {
-+			return mtk_nor_read_dma(sp, op->addr.val,
-+						op->data.nbytes,
-+						op->data.buf.in);
-+		}
-+	}
-+
-+	return -ENOTSUPP;
-+}
-+
-+static int mtk_nor_setup(struct spi_device *spi)
-+{
-+	struct mtk_nor *sp = spi_controller_get_devdata(spi->master);
-+
-+	if (spi->max_speed_hz && (spi->max_speed_hz < sp->spi_freq)) {
-+		dev_err(&spi->dev, "spi clock should be %u Hz.\n",
-+			sp->spi_freq);
-+		return -EINVAL;
-+	}
-+	spi->max_speed_hz = sp->spi_freq;
-+
-+	return 0;
-+}
-+
-+static int mtk_nor_transfer_one_message(struct spi_controller *master,
-+					struct spi_message *m)
-+{
-+	struct mtk_nor *sp = spi_controller_get_devdata(master);
-+	struct spi_transfer *t = NULL;
-+	unsigned long trx_len = 0;
-+	int stat = 0;
-+	int reg_offset = MTK_NOR_REG_PRGDATA_MAX;
-+	void __iomem *reg;
-+	const u8 *txbuf;
-+	u8 *rxbuf;
-+	int i;
-+
-+	list_for_each_entry(t, &m->transfers, transfer_list) {
-+		txbuf = t->tx_buf;
-+		for (i = 0; i < t->len; i++, reg_offset--) {
-+			reg = sp->base + MTK_NOR_REG_PRGDATA(reg_offset);
-+			if (txbuf)
-+				writeb(txbuf[i], reg);
-+			else
-+				writeb(0, reg);
-+		}
-+		trx_len += t->len;
-+	}
-+
-+	writel(trx_len * BITS_PER_BYTE, sp->base + MTK_NOR_REG_PRG_CNT);
-+
-+	stat = mtk_nor_cmd_exec(sp, MTK_NOR_CMD_PROGRAM,
-+				trx_len * BITS_PER_BYTE);
-+	if (stat < 0)
-+		goto msg_done;
-+
-+	reg_offset = trx_len - 1;
-+	list_for_each_entry(t, &m->transfers, transfer_list) {
-+		rxbuf = t->rx_buf;
-+		for (i = 0; i < t->len; i++, reg_offset--) {
-+			reg = sp->base + MTK_NOR_REG_SHIFT(reg_offset);
-+			if (rxbuf)
-+				rxbuf[i] = readb(reg);
-+		}
-+	}
-+
-+	m->actual_length = trx_len;
-+msg_done:
-+	m->status = stat;
-+	spi_finalize_current_message(master);
-+
-+	return 0;
-+}
-+
-+static void mtk_nor_disable_clk(struct mtk_nor *sp)
-+{
-+	clk_disable_unprepare(sp->spi_clk);
-+	clk_disable_unprepare(sp->ctlr_clk);
-+}
-+
-+static int mtk_nor_enable_clk(struct mtk_nor *sp)
-+{
-+	int ret;
-+
-+	ret = clk_prepare_enable(sp->spi_clk);
-+	if (ret)
-+		return ret;
-+
-+	ret = clk_prepare_enable(sp->ctlr_clk);
-+	if (ret) {
-+		clk_disable_unprepare(sp->spi_clk);
-+		return ret;
-+	}
-+
-+	return 0;
-+}
-+
-+static int mtk_nor_init(struct mtk_nor *sp)
-+{
-+	int ret;
-+
-+	ret = mtk_nor_enable_clk(sp);
-+	if (ret)
-+		return ret;
-+
-+	sp->spi_freq = clk_get_rate(sp->spi_clk);
-+
-+	writel(MTK_NOR_ENABLE_SF_CMD, sp->base + MTK_NOR_REG_WP);
-+	mtk_nor_rmw(sp, MTK_NOR_REG_CFG2, MTK_NOR_WR_CUSTOM_OP_EN, 0);
-+	mtk_nor_rmw(sp, MTK_NOR_REG_CFG3,
-+		    MTK_NOR_DISABLE_WREN | MTK_NOR_DISABLE_SR_POLL, 0);
-+
-+	return ret;
-+}
-+
-+static irqreturn_t mtk_nor_irq_handler(int irq, void *data)
-+{
-+	struct mtk_nor *sp = data;
-+	u32 irq_status, irq_enabled;
-+
-+	irq_status = readl(sp->base + MTK_NOR_REG_IRQ_STAT);
-+	irq_enabled = readl(sp->base + MTK_NOR_REG_IRQ_EN);
-+	// write status back to clear interrupt
-+	writel(irq_status, sp->base + MTK_NOR_REG_IRQ_STAT);
-+
-+	if (!(irq_status & irq_enabled))
-+		return IRQ_NONE;
-+
-+	if (irq_status & MTK_NOR_IRQ_DMA) {
-+		complete(&sp->op_done);
-+		writel(0, sp->base + MTK_NOR_REG_IRQ_EN);
-+	}
-+
-+	return IRQ_HANDLED;
-+}
-+
-+static size_t mtk_max_msg_size(struct spi_device *spi)
-+{
-+	return MTK_NOR_PRG_MAX_SIZE;
-+}
-+
-+static const struct spi_controller_mem_ops mtk_nor_mem_ops = {
-+	.adjust_op_size = mtk_nor_adjust_op_size,
-+	.supports_op = mtk_nor_supports_op,
-+	.exec_op = mtk_nor_exec_op
-+};
-+
-+static const struct of_device_id mtk_nor_match[] = {
-+	{ .compatible = "mediatek,mt8173-nor" },
-+	{ /* sentinel */ }
-+};
-+MODULE_DEVICE_TABLE(of, mtk_nor_match);
-+
-+static int mtk_nor_probe(struct platform_device *pdev)
-+{
-+	struct spi_controller *ctlr;
-+	struct mtk_nor *sp;
-+	void __iomem *base;
-+	u8 *buffer;
-+	struct clk *spi_clk, *ctlr_clk;
-+	int ret, irq;
-+
-+	base = devm_platform_ioremap_resource(pdev, 0);
-+	if (IS_ERR(base))
-+		return PTR_ERR(base);
-+
-+	spi_clk = devm_clk_get(&pdev->dev, "spi");
-+	if (IS_ERR(spi_clk))
-+		return PTR_ERR(spi_clk);
-+
-+	ctlr_clk = devm_clk_get(&pdev->dev, "sf");
-+	if (IS_ERR(ctlr_clk))
-+		return PTR_ERR(ctlr_clk);
-+
-+	buffer = devm_kmalloc(&pdev->dev,
-+			      MTK_NOR_BOUNCE_BUF_SIZE + MTK_NOR_DMA_ALIGN,
-+			      GFP_KERNEL);
-+	if (!buffer)
-+		return -ENOMEM;
-+
-+	if ((ulong)buffer & MTK_NOR_DMA_ALIGN_MASK)
-+		buffer = (u8 *)(((ulong)buffer + MTK_NOR_DMA_ALIGN) &
-+				~MTK_NOR_DMA_ALIGN_MASK);
-+
-+	ctlr = spi_alloc_master(&pdev->dev, sizeof(*sp));
-+	if (!ctlr) {
-+		dev_err(&pdev->dev, "failed to allocate spi controller\n");
-+		return -ENOMEM;
-+	}
-+
-+	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
-+	ctlr->dev.of_node = pdev->dev.of_node;
-+	ctlr->max_message_size = mtk_max_msg_size;
-+	ctlr->mem_ops = &mtk_nor_mem_ops;
-+	ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_TX_DUAL | SPI_TX_QUAD;
-+	ctlr->num_chipselect = 1;
-+	ctlr->setup = mtk_nor_setup;
-+	ctlr->transfer_one_message = mtk_nor_transfer_one_message;
-+
-+	dev_set_drvdata(&pdev->dev, ctlr);
-+
-+	sp = spi_controller_get_devdata(ctlr);
-+	sp->base = base;
-+	sp->buffer = buffer;
-+	sp->has_irq = false;
-+	sp->wbuf_en = false;
-+	sp->ctlr = ctlr;
-+	sp->dev = &pdev->dev;
-+	sp->spi_clk = spi_clk;
-+	sp->ctlr_clk = ctlr_clk;
-+
-+	irq = platform_get_irq_optional(pdev, 0);
-+	if (irq < 0) {
-+		dev_warn(sp->dev, "IRQ not available.");
-+	} else {
-+		writel(MTK_NOR_IRQ_MASK, base + MTK_NOR_REG_IRQ_STAT);
-+		writel(0, base + MTK_NOR_REG_IRQ_EN);
-+		ret = devm_request_irq(sp->dev, irq, mtk_nor_irq_handler, 0,
-+				       pdev->name, sp);
-+		if (ret < 0) {
-+			dev_warn(sp->dev, "failed to request IRQ.");
-+		} else {
-+			init_completion(&sp->op_done);
-+			sp->has_irq = true;
-+		}
-+	}
-+
-+	ret = mtk_nor_init(sp);
-+	if (ret < 0) {
-+		kfree(ctlr);
-+		return ret;
-+	}
-+
-+	dev_info(&pdev->dev, "spi frequency: %d Hz\n", sp->spi_freq);
-+
-+	return devm_spi_register_controller(&pdev->dev, ctlr);
-+}
-+
-+static int mtk_nor_remove(struct platform_device *pdev)
-+{
-+	struct spi_controller *ctlr;
-+	struct mtk_nor *sp;
-+
-+	ctlr = dev_get_drvdata(&pdev->dev);
-+	sp = spi_controller_get_devdata(ctlr);
-+
-+	mtk_nor_disable_clk(sp);
-+
-+	return 0;
-+}
-+
-+static struct platform_driver mtk_nor_driver = {
-+	.driver = {
-+		.name = DRIVER_NAME,
-+		.of_match_table = mtk_nor_match,
-+	},
-+	.probe = mtk_nor_probe,
-+	.remove = mtk_nor_remove,
-+};
-+
-+module_platform_driver(mtk_nor_driver);
-+
-+MODULE_DESCRIPTION("Mediatek SPI NOR controller driver");
-+MODULE_AUTHOR("Chuanhong Guo <gch981213@gmail.com>");
-+MODULE_LICENSE("GPL v2");
-+MODULE_ALIAS("platform:" DRIVER_NAME);
diff --git a/target/linux/mediatek/patches-5.4/0003-switch-add-mt7531.patch b/target/linux/mediatek/patches-5.4/0003-switch-add-mt7531.patch
deleted file mode 100644
index 6fae99c1f4..0000000000
--- a/target/linux/mediatek/patches-5.4/0003-switch-add-mt7531.patch
+++ /dev/null
@@ -1,19 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -329,6 +329,8 @@ config RTL8367B_PHY
- 
- endif # RTL8366_SMI
- 
-+source "drivers/net/phy/mtk/mt753x/Kconfig"
-+
- comment "MII PHY device drivers"
- 
- config SFP
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -109,3 +109,5 @@ obj-$(CONFIG_STE10XP)		+= ste10Xp.o
- obj-$(CONFIG_TERANETICS_PHY)	+= teranetics.o
- obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
- obj-$(CONFIG_XILINX_GMII2RGMII) += xilinx_gmii2rgmii.o
-+obj-$(CONFIG_MT753X_GSW)        += mtk/mt753x/
-+
diff --git a/target/linux/mediatek/patches-5.4/0005-dts-mt7622-add-gsw.patch b/target/linux/mediatek/patches-5.4/0005-dts-mt7622-add-gsw.patch
deleted file mode 100644
index d40cbfb853..0000000000
--- a/target/linux/mediatek/patches-5.4/0005-dts-mt7622-add-gsw.patch
+++ /dev/null
@@ -1,258 +0,0 @@
---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-@@ -53,6 +53,13 @@
- 		};
- 	};
- 
-+	gsw: gsw@0 {
-+		compatible = "mediatek,mt753x";
-+		mediatek,ethsys = <&ethsys>;
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+	};
-+
- 	leds {
- 		compatible = "gpio-leds";
- 
-@@ -146,6 +153,36 @@
- 	};
- };
- 
-+&gsw {
-+	mediatek,mdio = <&mdio>;
-+	mediatek,portmap = "wllll";
-+	mediatek,mdio_master_pinmux = <0>;
-+	reset-gpios = <&pio 54 0>;
-+	interrupt-parent = <&pio>;
-+	interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
-+	status = "okay";
-+
-+	port5: port@5 {
-+		compatible = "mediatek,mt753x-port";
-+		reg = <5>;
-+		phy-mode = "rgmii";
-+		fixed-link {
-+			speed = <1000>;
-+			full-duplex;
-+		};
-+	};
-+
-+	port6: port@6 {
-+		compatible = "mediatek,mt753x-port";
-+		reg = <6>;
-+		phy-mode = "sgmii";
-+		fixed-link {
-+			speed = <2500>;
-+			full-duplex;
-+		};
-+	};
-+};
-+
- &i2c1 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&i2c1_pins>;
---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-@@ -1,7 +1,6 @@
- /*
-- * Copyright (c) 2017 MediaTek Inc.
-- * Author: Ming Huang <ming.huang@mediatek.com>
-- *	   Sean Wang <sean.wang@mediatek.com>
-+ * Copyright (c) 2018 MediaTek Inc.
-+ * Author: Ryder Lee <ryder.lee@mediatek.com>
-  *
-  * SPDX-License-Identifier: (GPL-2.0 OR MIT)
-  */
-@@ -14,7 +13,7 @@
- #include "mt6380.dtsi"
- 
- / {
--	model = "MediaTek MT7622 RFB1 board";
-+	model = "MT7622_MT7531 RFB";
- 	compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";
- 
- 	aliases {
-@@ -23,7 +22,7 @@
- 
- 	chosen {
- 		stdout-path = "serial0:115200n8";
--		bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
-+		bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512";
- 	};
- 
- 	cpus {
-@@ -40,23 +39,36 @@
- 
- 	gpio-keys {
- 		compatible = "gpio-keys";
--		poll-interval = <100>;
- 
- 		factory {
- 			label = "factory";
- 			linux,code = <BTN_0>;
--			gpios = <&pio 0 0>;
-+			gpios = <&pio 0 GPIO_ACTIVE_LOW>;
- 		};
- 
- 		wps {
- 			label = "wps";
- 			linux,code = <KEY_WPS_BUTTON>;
--			gpios = <&pio 102 0>;
-+			gpios = <&pio 102 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		green {
-+			label = "bpi-r64:pio:green";
-+			gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		red {
-+			label = "bpi-r64:pio:red";
-+			gpios = <&pio 88 GPIO_ACTIVE_HIGH>;
- 		};
- 	};
- 
- 	memory {
--		reg = <0 0x40000000 0 0x20000000>;
-+		reg = <0 0x40000000 0 0x40000000>;
- 	};
- 
- 	reg_1p8v: regulator-1p8v {
-@@ -101,23 +113,82 @@
- };
- 
- &eth {
--	pinctrl-names = "default";
--	pinctrl-0 = <&eth_pins>;
- 	status = "okay";
-+	gmac0: mac@0 {
-+		compatible = "mediatek,eth-mac";
-+		reg = <0>;
-+		phy-mode = "2500base-x";
-+
-+		fixed-link {
-+			speed = <2500>;
-+			full-duplex;
-+			pause;
-+		};
-+	};
- 
- 	gmac1: mac@1 {
- 		compatible = "mediatek,eth-mac";
- 		reg = <1>;
--		phy-handle = <&phy5>;
-+		phy-mode = "rgmii";
-+
-+		fixed-link {
-+			speed = <1000>;
-+			full-duplex;
-+			pause;
-+		};
- 	};
- 
--	mdio-bus {
-+	mdio: mdio-bus {
- 		#address-cells = <1>;
- 		#size-cells = <0>;
- 
--		phy5: ethernet-phy@5 {
--			reg = <5>;
--			phy-mode = "sgmii";
-+		switch@0 {
-+			compatible = "mediatek,mt7531";
-+			reg = <0>;
-+			reset-gpios = <&pio 54 0>;
-+
-+			ports {
-+				#address-cells = <1>;
-+				#size-cells = <0>;
-+
-+				port@0 {
-+					reg = <0>;
-+					label = "lan1";
-+				};
-+
-+				port@1 {
-+					reg = <1>;
-+					label = "lan2";
-+				};
-+
-+				port@2 {
-+					reg = <2>;
-+					label = "lan3";
-+				};
-+
-+				port@3 {
-+					reg = <3>;
-+					label = "lan4";
-+				};
-+
-+				port@4 {
-+					reg = <4>;
-+					label = "wan";
-+				};
-+
-+				port@6 {
-+					reg = <6>;
-+					label = "cpu";
-+					ethernet = <&gmac0>;
-+					phy-mode = "2500base-x";
-+
-+					fixed-link {
-+						speed = <2500>;
-+						full-duplex;
-+						pause;
-+					};
-+				};
-+			};
- 		};
- 	};
- };
-@@ -185,15 +256,28 @@
- 
- &pcie {
- 	pinctrl-names = "default";
--	pinctrl-0 = <&pcie0_pins>;
-+	pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;
- 	status = "okay";
- 
- 	pcie@0,0 {
- 		status = "okay";
- 	};
-+
-+	pcie@1,0 {
-+		status = "okay";
-+	};
- };
- 
- &pio {
-+	/* Attention: GPIO 90 is used to switch between PCIe@1,0 and
-+	 * SATA functions. i.e. output-high: PCIe, output-low: SATA
-+	 */
-+	asm_sel {
-+		gpio-hog;
-+		gpios = <90 GPIO_ACTIVE_HIGH>;
-+		output-high;
-+	};
-+
- 	/* eMMC is shared pin with parallel NAND */
- 	emmc_pins_default: emmc-pins-default {
- 		mux {
-@@ -460,11 +544,11 @@
- };
- 
- &sata {
--	status = "okay";
-+	status = "disable";
- };
- 
- &sata_phy {
--	status = "okay";
-+	status = "disable";
- };
- 
- &spi0 {
diff --git a/target/linux/mediatek/patches-5.4/0005-dts-mt7629-add-gsw.patch b/target/linux/mediatek/patches-5.4/0005-dts-mt7629-add-gsw.patch
deleted file mode 100644
index 4028bad4df..0000000000
--- a/target/linux/mediatek/patches-5.4/0005-dts-mt7629-add-gsw.patch
+++ /dev/null
@@ -1,90 +0,0 @@
---- a/arch/arm/boot/dts/mt7629-rfb.dts
-+++ b/arch/arm/boot/dts/mt7629-rfb.dts
-@@ -18,6 +18,7 @@
- 
- 	chosen {
- 		stdout-path = "serial0:115200n8";
-+		bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8";
- 	};
- 
- 	gpio-keys {
-@@ -36,6 +37,13 @@
- 		};
- 	};
- 
-+	gsw: gsw@0 {
-+		compatible = "mediatek,mt753x";
-+		mediatek,ethsys = <&ethsys>;
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+	};
-+
- 	memory@40000000 {
- 		device_type = "memory";
- 		reg = <0x40000000 0x10000000>;
-@@ -70,6 +78,10 @@
- 		compatible = "mediatek,eth-mac";
- 		reg = <0>;
- 		phy-mode = "2500base-x";
-+
-+		nvmem-cells = <&macaddr_factory_2a>;
-+		nvmem-cell-names = "mac-address";
-+
- 		fixed-link {
- 			speed = <2500>;
- 			full-duplex;
-@@ -82,6 +94,9 @@
- 		reg = <1>;
- 		phy-mode = "gmii";
- 		phy-handle = <&phy0>;
-+
-+		nvmem-cells = <&macaddr_factory_24>;
-+		nvmem-cell-names = "mac-address";
- 	};
- 
- 	mdio: mdio-bus {
-@@ -94,6 +109,26 @@
- 	};
- };
- 
-+&gsw {
-+	mediatek,mdio = <&mdio>;
-+	mediatek,portmap = "llllw";
-+	mediatek,mdio_master_pinmux = <0>;
-+	reset-gpios = <&pio 28 0>;
-+	interrupt-parent = <&pio>;
-+	interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
-+	status = "okay";
-+
-+	port6: port@6 {
-+		compatible = "mediatek,mt753x-port";
-+		reg = <6>;
-+		phy-mode = "sgmii";
-+		fixed-link {
-+			speed = <2500>;
-+			full-duplex;
-+		};
-+	};
-+};
-+
- &i2c {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&i2c_pins>;
-@@ -272,3 +307,17 @@
- 	pinctrl-0 = <&watchdog_pins>;
- 	status = "okay";
- };
-+
-+&factory {
-+	compatible = "nvmem-cells";
-+	#address-cells = <1>;
-+	#size-cells = <1>;
-+
-+	macaddr_factory_24: macaddr@24 {
-+		reg = <0x24 0x6>;
-+	};
-+
-+	macaddr_factory_2a: macaddr@2a {
-+		reg = <0x2a 0x6>;
-+	};
-+};
diff --git a/target/linux/mediatek/patches-5.4/0006-dts-fix-bpi2-console.patch b/target/linux/mediatek/patches-5.4/0006-dts-fix-bpi2-console.patch
deleted file mode 100644
index b7251177f2..0000000000
--- a/target/linux/mediatek/patches-5.4/0006-dts-fix-bpi2-console.patch
+++ /dev/null
@@ -1,10 +0,0 @@
---- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
-+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
-@@ -19,6 +19,7 @@
- 
- 	chosen {
- 		stdout-path = "serial2:115200n8";
-+		bootargs = "console=ttyS2,115200n8";
- 	};
- 
- 	cpus {
diff --git a/target/linux/mediatek/patches-5.4/0006-dts-fix-bpi64-console.patch b/target/linux/mediatek/patches-5.4/0006-dts-fix-bpi64-console.patch
deleted file mode 100644
index 07a2eae245..0000000000
--- a/target/linux/mediatek/patches-5.4/0006-dts-fix-bpi64-console.patch
+++ /dev/null
@@ -1,11 +0,0 @@
---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-@@ -22,7 +22,7 @@
- 
- 	chosen {
- 		stdout-path = "serial0:115200n8";
--		bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512";
-+		bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512";
- 	};
- 
- 	cpus {
diff --git a/target/linux/mediatek/patches-5.4/0010-dts-mt7629-rfb-fix-firmware-partition.patch b/target/linux/mediatek/patches-5.4/0010-dts-mt7629-rfb-fix-firmware-partition.patch
deleted file mode 100644
index 2c48e5706f..0000000000
--- a/target/linux/mediatek/patches-5.4/0010-dts-mt7629-rfb-fix-firmware-partition.patch
+++ /dev/null
@@ -1,13 +0,0 @@
---- a/arch/arm/boot/dts/mt7629-rfb.dts
-+++ b/arch/arm/boot/dts/mt7629-rfb.dts
-@@ -168,8 +168,9 @@
- 			};
- 
- 			partition@b0000 {
--				label = "kernel";
-+				label = "firmware";
- 				reg = <0xb0000 0xb50000>;
-+				compatible = "denx,fit";
- 			};
- 		};
- 	};
diff --git a/target/linux/mediatek/patches-5.4/0226-phy-phy-mtk-tphy-Add-hifsys-support.patch b/target/linux/mediatek/patches-5.4/0226-phy-phy-mtk-tphy-Add-hifsys-support.patch
deleted file mode 100644
index f2647e8ffe..0000000000
--- a/target/linux/mediatek/patches-5.4/0226-phy-phy-mtk-tphy-Add-hifsys-support.patch
+++ /dev/null
@@ -1,66 +0,0 @@
-From 28f9a5e2a3f5441ab5594669ed82da11e32277a9 Mon Sep 17 00:00:00 2001
-From: Kristian Evensen <kristian.evensen@gmail.com>
-Date: Mon, 30 Apr 2018 14:38:01 +0200
-Subject: [PATCH] phy: phy-mtk-tphy: Add hifsys-support
-
----
- drivers/phy/mediatek/phy-mtk-tphy.c | 20 ++++++++++++++++++++
- 1 file changed, 20 insertions(+)
-
---- a/drivers/phy/mediatek/phy-mtk-tphy.c
-+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
-@@ -15,6 +15,8 @@
- #include <linux/of_device.h>
- #include <linux/phy/phy.h>
- #include <linux/platform_device.h>
-+#include <linux/mfd/syscon.h>
-+#include <linux/regmap.h>
- 
- /* version V1 sub-banks offset base address */
- /* banks shared by multiple phys */
-@@ -263,6 +265,9 @@
- #define RG_CDR_BIRLTD0_GEN3_MSK		GENMASK(4, 0)
- #define RG_CDR_BIRLTD0_GEN3_VAL(x)	(0x1f & (x))
- 
-+#define HIF_SYSCFG1			0x14
-+#define HIF_SYSCFG1_PHY2_MASK		(0x3 << 20)
-+
- enum mtk_phy_version {
- 	MTK_PHY_V1 = 1,
- 	MTK_PHY_V2,
-@@ -310,6 +315,7 @@ struct mtk_tphy {
- 	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
- 	const struct mtk_phy_pdata *pdata;
- 	struct mtk_phy_instance **phys;
-+	struct regmap *hif;
- 	int nphys;
- 	int src_ref_clk; /* MHZ, reference clock for slew rate calibrate */
- 	int src_coef; /* coefficient for slew rate calibrate */
-@@ -629,6 +635,10 @@ static void pcie_phy_instance_init(struc
- 	if (tphy->pdata->version != MTK_PHY_V1)
- 		return;
- 
-+	if (tphy->hif)
-+		regmap_update_bits(tphy->hif, HIF_SYSCFG1,
-+				   HIF_SYSCFG1_PHY2_MASK, 0);
-+
- 	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG0);
- 	tmp &= ~(P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H);
- 	tmp |= P3A_RG_XTAL_EXT_PE1H_VAL(0x2) | P3A_RG_XTAL_EXT_PE2H_VAL(0x2);
-@@ -1114,6 +1124,16 @@ static int mtk_tphy_probe(struct platfor
- 		&tphy->src_ref_clk);
- 	device_property_read_u32(dev, "mediatek,src-coef", &tphy->src_coef);
- 
-+	if (of_find_property(np, "mediatek,phy-switch", NULL)) {
-+		tphy->hif = syscon_regmap_lookup_by_phandle(np,
-+							    "mediatek,phy-switch");
-+		if (IS_ERR(tphy->hif)) {
-+			dev_err(&pdev->dev,
-+				"missing \"mediatek,phy-switch\" phandle\n");
-+			return PTR_ERR(tphy->hif);
-+		}
-+	}
-+
- 	port = 0;
- 	for_each_child_of_node(np, child_np) {
- 		struct mtk_phy_instance *instance;
diff --git a/target/linux/mediatek/patches-5.4/0301-mtd-mtk-ecc-move-mtk-ecc-header-file-to-include-mtd.patch b/target/linux/mediatek/patches-5.4/0301-mtd-mtk-ecc-move-mtk-ecc-header-file-to-include-mtd.patch
deleted file mode 100644
index d9ab339fa8..0000000000
--- a/target/linux/mediatek/patches-5.4/0301-mtd-mtk-ecc-move-mtk-ecc-header-file-to-include-mtd.patch
+++ /dev/null
@@ -1,139 +0,0 @@
-From a2479dc254ebe31c84fbcfda73f35e2321576494 Mon Sep 17 00:00:00 2001
-From: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
-Date: Tue, 19 Mar 2019 13:57:38 +0800
-Subject: [PATCH 1/6] mtd: mtk ecc: move mtk ecc header file to include/mtd
-
-Change-Id: I8dc1d30e21b40d68ef5efd9587012f82970156a5
-Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
----
- drivers/mtd/nand/raw/mtk_ecc.c                        | 3 +--
- drivers/mtd/nand/raw/mtk_nand.c                       | 2 +-
- {drivers/mtd/nand/raw => include/linux/mtd}/mtk_ecc.h | 0
- 3 files changed, 2 insertions(+), 3 deletions(-)
- rename {drivers/mtd/nand/raw => include/linux/mtd}/mtk_ecc.h (100%)
-
---- a/drivers/mtd/nand/raw/mtk_ecc.c
-+++ b/drivers/mtd/nand/raw/mtk_ecc.c
-@@ -15,8 +15,7 @@
- #include <linux/of.h>
- #include <linux/of_platform.h>
- #include <linux/mutex.h>
--
--#include "mtk_ecc.h"
-+#include <linux/mtd/mtk_ecc.h>
- 
- #define ECC_IDLE_MASK		BIT(0)
- #define ECC_IRQ_EN		BIT(0)
---- a/drivers/mtd/nand/raw/mtk_nand.c
-+++ b/drivers/mtd/nand/raw/mtk_nand.c
-@@ -17,7 +17,7 @@
- #include <linux/iopoll.h>
- #include <linux/of.h>
- #include <linux/of_device.h>
--#include "mtk_ecc.h"
-+#include <linux/mtd/mtk_ecc.h>
- 
- /* NAND controller register definition */
- #define NFI_CNFG		(0x00)
---- /dev/null
-+++ b/include/linux/mtd/mtk_ecc.h
-@@ -0,0 +1,49 @@
-+/*
-+ * MTK SDG1 ECC controller
-+ *
-+ * Copyright (c) 2016 Mediatek
-+ * Authors:	Xiaolei Li		<xiaolei.li@mediatek.com>
-+ *		Jorge Ramirez-Ortiz	<jorge.ramirez-ortiz@linaro.org>
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published
-+ * by the Free Software Foundation.
-+ */
-+
-+#ifndef __DRIVERS_MTD_NAND_MTK_ECC_H__
-+#define __DRIVERS_MTD_NAND_MTK_ECC_H__
-+
-+#include <linux/types.h>
-+
-+enum mtk_ecc_mode {ECC_DMA_MODE = 0, ECC_NFI_MODE = 1};
-+enum mtk_ecc_operation {ECC_ENCODE, ECC_DECODE};
-+
-+struct device_node;
-+struct mtk_ecc;
-+
-+struct mtk_ecc_stats {
-+	u32 corrected;
-+	u32 bitflips;
-+	u32 failed;
-+};
-+
-+struct mtk_ecc_config {
-+	enum mtk_ecc_operation op;
-+	enum mtk_ecc_mode mode;
-+	dma_addr_t addr;
-+	u32 strength;
-+	u32 sectors;
-+	u32 len;
-+};
-+
-+int mtk_ecc_encode(struct mtk_ecc *, struct mtk_ecc_config *, u8 *, u32);
-+void mtk_ecc_get_stats(struct mtk_ecc *, struct mtk_ecc_stats *, int);
-+int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation);
-+int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *);
-+void mtk_ecc_disable(struct mtk_ecc *);
-+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p);
-+unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc);
-+
-+struct mtk_ecc *of_mtk_ecc_get(struct device_node *);
-+void mtk_ecc_release(struct mtk_ecc *);
-+
-+#endif
---- a/drivers/mtd/nand/raw/mtk_ecc.h
-+++ /dev/null
-@@ -1,47 +0,0 @@
--/* SPDX-License-Identifier: GPL-2.0 OR MIT */
--/*
-- * MTK SDG1 ECC controller
-- *
-- * Copyright (c) 2016 Mediatek
-- * Authors:	Xiaolei Li		<xiaolei.li@mediatek.com>
-- *		Jorge Ramirez-Ortiz	<jorge.ramirez-ortiz@linaro.org>
-- */
--
--#ifndef __DRIVERS_MTD_NAND_MTK_ECC_H__
--#define __DRIVERS_MTD_NAND_MTK_ECC_H__
--
--#include <linux/types.h>
--
--enum mtk_ecc_mode {ECC_DMA_MODE = 0, ECC_NFI_MODE = 1};
--enum mtk_ecc_operation {ECC_ENCODE, ECC_DECODE};
--
--struct device_node;
--struct mtk_ecc;
--
--struct mtk_ecc_stats {
--	u32 corrected;
--	u32 bitflips;
--	u32 failed;
--};
--
--struct mtk_ecc_config {
--	enum mtk_ecc_operation op;
--	enum mtk_ecc_mode mode;
--	dma_addr_t addr;
--	u32 strength;
--	u32 sectors;
--	u32 len;
--};
--
--int mtk_ecc_encode(struct mtk_ecc *, struct mtk_ecc_config *, u8 *, u32);
--void mtk_ecc_get_stats(struct mtk_ecc *, struct mtk_ecc_stats *, int);
--int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation);
--int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *);
--void mtk_ecc_disable(struct mtk_ecc *);
--void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p);
--unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc);
--
--struct mtk_ecc *of_mtk_ecc_get(struct device_node *);
--void mtk_ecc_release(struct mtk_ecc *);
--
--#endif
diff --git a/target/linux/mediatek/patches-5.4/0303-mtd-spinand-disable-on-die-ECC.patch b/target/linux/mediatek/patches-5.4/0303-mtd-spinand-disable-on-die-ECC.patch
deleted file mode 100644
index 5c18ea0f74..0000000000
--- a/target/linux/mediatek/patches-5.4/0303-mtd-spinand-disable-on-die-ECC.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From b341f120cfc9ca1dfd48364b7f36ac2c1fbdea43 Mon Sep 17 00:00:00 2001
-From: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
-Date: Wed, 3 Apr 2019 16:30:01 +0800
-Subject: [PATCH 3/6] mtd: spinand: disable on-die ECC
-
-Change-Id: I9745adaed5295202fabbe8ab8947885c57a5b847
-Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
----
- drivers/mtd/nand/spi/core.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/mtd/nand/spi/core.c
-+++ b/drivers/mtd/nand/spi/core.c
-@@ -491,7 +491,7 @@ static int spinand_mtd_read(struct mtd_i
- 	int ret = 0;
- 
- 	if (ops->mode != MTD_OPS_RAW && spinand->eccinfo.ooblayout)
--		enable_ecc = true;
-+		enable_ecc = false;
- 
- 	mutex_lock(&spinand->lock);
- 
-@@ -539,7 +539,7 @@ static int spinand_mtd_write(struct mtd_
- 	int ret = 0;
- 
- 	if (ops->mode != MTD_OPS_RAW && mtd->ooblayout)
--		enable_ecc = true;
-+		enable_ecc = false;
- 
- 	mutex_lock(&spinand->lock);
- 
diff --git a/target/linux/mediatek/patches-5.4/0306-spi-spi-mem-MediaTek-Add-SPI-NAND-Flash-interface-dr.patch b/target/linux/mediatek/patches-5.4/0306-spi-spi-mem-MediaTek-Add-SPI-NAND-Flash-interface-dr.patch
deleted file mode 100644
index b3672e5b15..0000000000
--- a/target/linux/mediatek/patches-5.4/0306-spi-spi-mem-MediaTek-Add-SPI-NAND-Flash-interface-dr.patch
+++ /dev/null
@@ -1,1246 +0,0 @@
-From 1ecb38eabd90efe93957d0a822a167560c39308a Mon Sep 17 00:00:00 2001
-From: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
-Date: Wed, 20 Mar 2019 16:19:51 +0800
-Subject: [PATCH 6/6] spi: spi-mem: MediaTek: Add SPI NAND Flash interface
- driver for MediaTek MT7622
-
-Change-Id: I3e78406bb9b46b0049d3988a5c71c7069e4f809c
-Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
----
- drivers/spi/Kconfig        |    9 +
- drivers/spi/Makefile       |    1 +
- drivers/spi/spi-mtk-snfi.c | 1183 ++++++++++++++++++++++++++++++++++++
- 3 files changed, 1193 insertions(+)
- create mode 100644 drivers/spi/spi-mtk-snfi.c
-
---- a/drivers/spi/Makefile
-+++ b/drivers/spi/Makefile
-@@ -60,6 +60,7 @@ obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mp
- obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mpc52xx-psc.o
- obj-$(CONFIG_SPI_MPC52xx)		+= spi-mpc52xx.o
- obj-$(CONFIG_SPI_MT65XX)                += spi-mt65xx.o
-+obj-$(CONFIG_SPI_MTK_SNFI)              += spi-mtk-snfi.o
- obj-$(CONFIG_SPI_MT7621)		+= spi-mt7621.o
- obj-$(CONFIG_SPI_MTK_NOR)		+= spi-mtk-nor.o
- obj-$(CONFIG_SPI_MXIC)			+= spi-mxic.o
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -427,6 +427,15 @@ config SPI_MT65XX
- 	  say Y or M here.If you are not sure, say N.
- 	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
- 
-+config SPI_MTK_SNFI
-+	tristate "MediaTek SPI NAND interface"
-+	select MTD_SPI_NAND
-+	help
-+	  This selects the SPI NAND FLASH interface(SNFI),
-+	  which could be found on MediaTek Soc.
-+	  Say Y or M here.If you are not sure, say N.
-+	  Note Parallel Nand and SPI NAND is alternative on MediaTek SoCs.
-+
- config SPI_MT7621
- 	tristate "MediaTek MT7621 SPI Controller"
- 	depends on RALINK || COMPILE_TEST
---- /dev/null
-+++ b/drivers/spi/spi-mtk-snfi.c
-@@ -0,0 +1,1200 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Driver for MediaTek SPI Nand interface
-+ *
-+ * Copyright (C) 2018 MediaTek Inc.
-+ * Authors:	Xiangsheng Hou	<xiangsheng.hou@mediatek.com>
-+ *
-+ */
-+
-+#include <linux/clk.h>
-+#include <linux/delay.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/interrupt.h>
-+#include <linux/iopoll.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/mtk_ecc.h>
-+#include <linux/mtd/spinand.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/of_device.h>
-+#include <linux/platform_device.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/spi-mem.h>
-+
-+/* NAND controller register definition */
-+/* NFI control */
-+#define NFI_CNFG		0x00
-+#define		CNFG_DMA		BIT(0)
-+#define		CNFG_READ_EN		BIT(1)
-+#define		CNFG_DMA_BURST_EN	BIT(2)
-+#define		CNFG_BYTE_RW		BIT(6)
-+#define		CNFG_HW_ECC_EN		BIT(8)
-+#define		CNFG_AUTO_FMT_EN	BIT(9)
-+#define		CNFG_OP_PROGRAM		(3UL << 12)
-+#define		CNFG_OP_CUST		(6UL << 12)
-+#define NFI_PAGEFMT		0x04
-+#define		PAGEFMT_512		0
-+#define		PAGEFMT_2K		1
-+#define		PAGEFMT_4K		2
-+#define		PAGEFMT_FDM_SHIFT	8
-+#define		PAGEFMT_FDM_ECC_SHIFT	12
-+#define NFI_CON			0x08
-+#define		CON_FIFO_FLUSH		BIT(0)
-+#define		CON_NFI_RST		BIT(1)
-+#define		CON_BRD			BIT(8)
-+#define		CON_BWR			BIT(9)
-+#define		CON_SEC_SHIFT		12
-+#define NFI_INTR_EN		0x10
-+#define		INTR_AHB_DONE_EN	BIT(6)
-+#define NFI_INTR_STA		0x14
-+#define NFI_CMD			0x20
-+#define NFI_STA			0x60
-+#define		STA_EMP_PAGE		BIT(12)
-+#define		NAND_FSM_MASK		(0x1f << 24)
-+#define		NFI_FSM_MASK		(0xf << 16)
-+#define NFI_ADDRCNTR		0x70
-+#define		CNTR_MASK		GENMASK(16, 12)
-+#define		ADDRCNTR_SEC_SHIFT	12
-+#define		ADDRCNTR_SEC(val) \
-+		(((val) & CNTR_MASK) >> ADDRCNTR_SEC_SHIFT)
-+#define NFI_STRADDR		0x80
-+#define NFI_BYTELEN		0x84
-+#define NFI_CSEL		0x90
-+#define NFI_FDML(x)		(0xa0 + (x) * sizeof(u32) * 2)
-+#define NFI_FDMM(x)		(0xa4 + (x) * sizeof(u32) * 2)
-+#define NFI_MASTER_STA		0x224
-+#define		MASTER_STA_MASK		0x0fff
-+/* NFI_SPI control */
-+#define SNFI_MAC_OUTL		0x504
-+#define SNFI_MAC_INL		0x508
-+#define SNFI_RD_CTL2		0x510
-+#define		RD_CMD_MASK		0x00ff
-+#define		RD_DUMMY_SHIFT		8
-+#define SNFI_RD_CTL3		0x514
-+#define		RD_ADDR_MASK		0xffff
-+#define SNFI_MISC_CTL		0x538
-+#define		RD_MODE_X2		BIT(16)
-+#define		RD_MODE_X4		(2UL << 16)
-+#define		RD_QDUAL_IO		(4UL << 16)
-+#define		RD_MODE_MASK		(7UL << 16)
-+#define		RD_CUSTOM_EN		BIT(6)
-+#define		WR_CUSTOM_EN		BIT(7)
-+#define		WR_X4_EN		BIT(20)
-+#define		SW_RST			BIT(28)
-+#define SNFI_MISC_CTL2		0x53c
-+#define		WR_LEN_SHIFT		16
-+#define SNFI_PG_CTL1		0x524
-+#define		WR_LOAD_CMD_SHIFT	8
-+#define SNFI_PG_CTL2		0x528
-+#define		WR_LOAD_ADDR_MASK	0xffff
-+#define SNFI_MAC_CTL		0x500
-+#define		MAC_WIP			BIT(0)
-+#define		MAC_WIP_READY		BIT(1)
-+#define		MAC_TRIG		BIT(2)
-+#define		MAC_EN			BIT(3)
-+#define		MAC_SIO_SEL		BIT(4)
-+#define SNFI_STA_CTL1		0x550
-+#define		SPI_STATE_IDLE		0xf
-+#define SNFI_CNFG		0x55c
-+#define		SNFI_MODE_EN		BIT(0)
-+#define SNFI_GPRAM_DATA		0x800
-+#define		SNFI_GPRAM_MAX_LEN	16
-+
-+/* Dummy command trigger NFI to spi mode */
-+#define NAND_CMD_DUMMYREAD	0x00
-+#define NAND_CMD_DUMMYPROG	0x80
-+
-+#define MTK_TIMEOUT		500000
-+#define MTK_RESET_TIMEOUT	1000000
-+#define MTK_SNFC_MIN_SPARE	16
-+#define KB(x)			((x) * 1024UL)
-+
-+/*
-+ * supported spare size of each IP.
-+ * order should be the same with the spare size bitfiled defination of
-+ * register NFI_PAGEFMT.
-+ */
-+static const u8 spare_size_mt7622[] = {
-+	16, 26, 27, 28
-+};
-+
-+struct mtk_snfi_caps {
-+	const u8 *spare_size;
-+	u8 num_spare_size;
-+	u32 nand_sec_size;
-+	u8 nand_fdm_size;
-+	u8 nand_fdm_ecc_size;
-+	u8 ecc_parity_bits;
-+	u8 pageformat_spare_shift;
-+	u8 bad_mark_swap;
-+};
-+
-+struct mtk_snfi_bad_mark_ctl {
-+	void (*bm_swap)(struct spi_mem *mem, u8 *buf, int raw);
-+	u32 sec;
-+	u32 pos;
-+};
-+
-+struct mtk_snfi_nand_chip {
-+	struct mtk_snfi_bad_mark_ctl bad_mark;
-+	u32 spare_per_sector;
-+};
-+
-+struct mtk_snfi_clk {
-+	struct clk *nfi_clk;
-+	struct clk *spi_clk;
-+};
-+
-+struct mtk_snfi {
-+	const struct mtk_snfi_caps *caps;
-+	struct mtk_snfi_nand_chip snfi_nand;
-+	struct mtk_snfi_clk clk;
-+	struct mtk_ecc_config ecc_cfg;
-+	struct mtk_ecc *ecc;
-+	struct completion done;
-+	struct device *dev;
-+
-+	void __iomem *regs;
-+
-+	u8 *buffer;
-+};
-+
-+static inline u8 *oob_ptr(struct spi_mem *mem, int i)
-+{
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+	u8 *poi;
-+
-+	/* map the sector's FDM data to free oob:
-+	 * the beginning of the oob area stores the FDM data of bad mark
-+	 */
-+
-+	if (i < snfi_nand->bad_mark.sec)
-+		poi = spinand->oobbuf + (i + 1) * snfi->caps->nand_fdm_size;
-+	else if (i == snfi_nand->bad_mark.sec)
-+		poi = spinand->oobbuf;
-+	else
-+		poi = spinand->oobbuf + i * snfi->caps->nand_fdm_size;
-+
-+	return poi;
-+}
-+
-+static inline int mtk_data_len(struct spi_mem *mem)
-+{
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+
-+	return snfi->caps->nand_sec_size + snfi_nand->spare_per_sector;
-+}
-+
-+static inline u8 *mtk_oob_ptr(struct spi_mem *mem,
-+			      const u8 *p, int i)
-+{
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+
-+	return (u8 *)p + i * mtk_data_len(mem) + snfi->caps->nand_sec_size;
-+}
-+
-+static void mtk_snfi_bad_mark_swap(struct spi_mem *mem,
-+				   u8 *buf, int raw)
-+{
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+	u32 bad_pos = snfi_nand->bad_mark.pos;
-+
-+	if (raw)
-+		bad_pos += snfi_nand->bad_mark.sec * mtk_data_len(mem);
-+	else
-+		bad_pos += snfi_nand->bad_mark.sec * snfi->caps->nand_sec_size;
-+
-+	swap(spinand->oobbuf[0], buf[bad_pos]);
-+}
-+
-+static void mtk_snfi_set_bad_mark_ctl(struct mtk_snfi_bad_mark_ctl *bm_ctl,
-+				      struct spi_mem *mem)
-+{
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+
-+	bm_ctl->bm_swap = mtk_snfi_bad_mark_swap;
-+	bm_ctl->sec = mtd->writesize / mtk_data_len(mem);
-+	bm_ctl->pos = mtd->writesize % mtk_data_len(mem);
-+}
-+
-+static void mtk_snfi_mac_enable(struct mtk_snfi *snfi)
-+{
-+	u32 mac;
-+
-+	mac = readl(snfi->regs + SNFI_MAC_CTL);
-+	mac &= ~MAC_SIO_SEL;
-+	mac |= MAC_EN;
-+
-+	writel(mac, snfi->regs + SNFI_MAC_CTL);
-+}
-+
-+static int mtk_snfi_mac_trigger(struct mtk_snfi *snfi)
-+{
-+	u32 mac, reg;
-+	int ret = 0;
-+
-+	mac = readl(snfi->regs + SNFI_MAC_CTL);
-+	mac |= MAC_TRIG;
-+	writel(mac, snfi->regs + SNFI_MAC_CTL);
-+
-+	ret = readl_poll_timeout_atomic(snfi->regs + SNFI_MAC_CTL, reg,
-+					reg & MAC_WIP_READY, 10,
-+					MTK_TIMEOUT);
-+	if (ret < 0) {
-+		dev_err(snfi->dev, "polling wip ready for read timeout\n");
-+		return -EIO;
-+	}
-+
-+	ret = readl_poll_timeout_atomic(snfi->regs + SNFI_MAC_CTL, reg,
-+					!(reg & MAC_WIP), 10,
-+					MTK_TIMEOUT);
-+	if (ret < 0) {
-+		dev_err(snfi->dev, "polling flash update timeout\n");
-+		return -EIO;
-+	}
-+
-+	return ret;
-+}
-+
-+static void mtk_snfi_mac_leave(struct mtk_snfi *snfi)
-+{
-+	u32 mac;
-+
-+	mac = readl(snfi->regs + SNFI_MAC_CTL);
-+	mac &= ~(MAC_TRIG | MAC_EN | MAC_SIO_SEL);
-+	writel(mac, snfi->regs + SNFI_MAC_CTL);
-+}
-+
-+static int mtk_snfi_mac_op(struct mtk_snfi *snfi)
-+{
-+	int ret = 0;
-+
-+	mtk_snfi_mac_enable(snfi);
-+
-+	ret = mtk_snfi_mac_trigger(snfi);
-+	if (ret)
-+		return ret;
-+
-+	mtk_snfi_mac_leave(snfi);
-+
-+	return ret;
-+}
-+
-+static irqreturn_t mtk_snfi_irq(int irq, void *id)
-+{
-+	struct mtk_snfi *snfi = id;
-+	u16 sta, ien;
-+
-+	sta = readw(snfi->regs + NFI_INTR_STA);
-+	ien = readw(snfi->regs + NFI_INTR_EN);
-+
-+	if (!(sta & ien))
-+		return IRQ_NONE;
-+
-+	writew(~sta & ien, snfi->regs + NFI_INTR_EN);
-+	complete(&snfi->done);
-+
-+	return IRQ_HANDLED;
-+}
-+
-+static int mtk_snfi_enable_clk(struct device *dev, struct mtk_snfi_clk *clk)
-+{
-+	int ret;
-+
-+	ret = clk_prepare_enable(clk->nfi_clk);
-+	if (ret) {
-+		dev_err(dev, "failed to enable nfi clk\n");
-+		return ret;
-+	}
-+
-+	ret = clk_prepare_enable(clk->spi_clk);
-+	if (ret) {
-+		dev_err(dev, "failed to enable spi clk\n");
-+		clk_disable_unprepare(clk->nfi_clk);
-+		return ret;
-+	}
-+
-+	return 0;
-+}
-+
-+static void mtk_snfi_disable_clk(struct mtk_snfi_clk *clk)
-+{
-+	clk_disable_unprepare(clk->nfi_clk);
-+	clk_disable_unprepare(clk->spi_clk);
-+}
-+
-+static int mtk_snfi_reset(struct mtk_snfi *snfi)
-+{
-+	u32 val;
-+	int ret;
-+
-+	/* SW reset controller */
-+	val = readl(snfi->regs + SNFI_MISC_CTL) | SW_RST;
-+	writel(val, snfi->regs + SNFI_MISC_CTL);
-+
-+	ret = readw_poll_timeout(snfi->regs + SNFI_STA_CTL1, val,
-+				 !(val & SPI_STATE_IDLE), 50,
-+				 MTK_RESET_TIMEOUT);
-+	if (ret) {
-+		dev_warn(snfi->dev, "spi state active in reset [0x%x] = 0x%x\n",
-+			 SNFI_STA_CTL1, val);
-+		return ret;
-+	}
-+
-+	val = readl(snfi->regs + SNFI_MISC_CTL);
-+	val &= ~SW_RST;
-+	writel(val, snfi->regs + SNFI_MISC_CTL);
-+
-+	/* reset all registers and force the NFI master to terminate */
-+	writew(CON_FIFO_FLUSH | CON_NFI_RST, snfi->regs + NFI_CON);
-+	ret = readw_poll_timeout(snfi->regs + NFI_STA, val,
-+				 !(val & (NFI_FSM_MASK | NAND_FSM_MASK)), 50,
-+				 MTK_RESET_TIMEOUT);
-+	if (ret) {
-+		dev_warn(snfi->dev, "nfi active in reset [0x%x] = 0x%x\n",
-+			 NFI_STA, val);
-+		return ret;
-+	}
-+
-+	return 0;
-+}
-+
-+static int mtk_snfi_set_spare_per_sector(struct spinand_device *spinand,
-+					 const struct mtk_snfi_caps *caps,
-+					 u32 *sps)
-+{
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	const u8 *spare = caps->spare_size;
-+	u32 sectors, i, closest_spare = 0;
-+
-+	sectors = mtd->writesize / caps->nand_sec_size;
-+	*sps = mtd->oobsize / sectors;
-+
-+	if (*sps < MTK_SNFC_MIN_SPARE)
-+		return -EINVAL;
-+
-+	for (i = 0; i < caps->num_spare_size; i++) {
-+		if (*sps >= spare[i] && spare[i] >= spare[closest_spare]) {
-+			closest_spare = i;
-+			if (*sps == spare[i])
-+				break;
-+		}
-+	}
-+
-+	*sps = spare[closest_spare];
-+
-+	return 0;
-+}
-+
-+static void mtk_snfi_read_fdm_data(struct spi_mem *mem,
-+				   u32 sectors)
-+{
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	const struct mtk_snfi_caps *caps = snfi->caps;
-+	u32 vall, valm;
-+	int i, j;
-+	u8 *oobptr;
-+
-+	for (i = 0; i < sectors; i++) {
-+		oobptr = oob_ptr(mem, i);
-+		vall = readl(snfi->regs + NFI_FDML(i));
-+		valm = readl(snfi->regs + NFI_FDMM(i));
-+
-+		for (j = 0; j < caps->nand_fdm_size; j++)
-+			oobptr[j] = (j >= 4 ? valm : vall) >> ((j % 4) * 8);
-+	}
-+}
-+
-+static void mtk_snfi_write_fdm_data(struct spi_mem *mem,
-+				    u32 sectors)
-+{
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	const struct mtk_snfi_caps *caps = snfi->caps;
-+	u32 vall, valm;
-+	int i, j;
-+	u8 *oobptr;
-+
-+	for (i = 0; i < sectors; i++) {
-+		oobptr = oob_ptr(mem, i);
-+		vall = 0;
-+		valm = 0;
-+		for (j = 0; j < 8; j++) {
-+			if (j < 4)
-+				vall |= (j < caps->nand_fdm_size ? oobptr[j] :
-+					 0xff) << (j * 8);
-+			else
-+				valm |= (j < caps->nand_fdm_size ? oobptr[j] :
-+					 0xff) << ((j - 4) * 8);
-+		}
-+		writel(vall, snfi->regs + NFI_FDML(i));
-+		writel(valm, snfi->regs + NFI_FDMM(i));
-+	}
-+}
-+
-+static int mtk_snfi_update_ecc_stats(struct spi_mem *mem,
-+				     u8 *buf, u32 sectors)
-+{
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct mtk_ecc_stats stats;
-+	int rc, i;
-+
-+	rc = readl(snfi->regs + NFI_STA) & STA_EMP_PAGE;
-+	if (rc) {
-+		memset(buf, 0xff, sectors * snfi->caps->nand_sec_size);
-+		for (i = 0; i < sectors; i++)
-+			memset(spinand->oobbuf, 0xff,
-+			       snfi->caps->nand_fdm_size);
-+		return 0;
-+	}
-+
-+	mtk_ecc_get_stats(snfi->ecc, &stats, sectors);
-+	mtd->ecc_stats.corrected += stats.corrected;
-+	mtd->ecc_stats.failed += stats.failed;
-+
-+	return 0;
-+}
-+
-+static int mtk_snfi_hw_runtime_config(struct spi_mem *mem)
-+{
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	struct nand_device *nand = mtd_to_nanddev(mtd);
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	const struct mtk_snfi_caps *caps = snfi->caps;
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+	u32 fmt, spare, i = 0;
-+	int ret;
-+
-+	ret = mtk_snfi_set_spare_per_sector(spinand, caps, &spare);
-+	if (ret)
-+		return ret;
-+
-+	/* calculate usable oob bytes for ecc parity data */
-+	snfi_nand->spare_per_sector = spare;
-+	spare -= caps->nand_fdm_size;
-+
-+	nand->memorg.oobsize = snfi_nand->spare_per_sector
-+		* (mtd->writesize / caps->nand_sec_size);
-+	mtd->oobsize = nanddev_per_page_oobsize(nand);
-+
-+	snfi->ecc_cfg.strength = (spare << 3) / caps->ecc_parity_bits;
-+	mtk_ecc_adjust_strength(snfi->ecc, &snfi->ecc_cfg.strength);
-+
-+	switch (mtd->writesize) {
-+	case 512:
-+		fmt = PAGEFMT_512;
-+		break;
-+	case KB(2):
-+		fmt = PAGEFMT_2K;
-+		break;
-+	case KB(4):
-+		fmt = PAGEFMT_4K;
-+		break;
-+	default:
-+		dev_err(snfi->dev, "invalid page len: %d\n", mtd->writesize);
-+		return -EINVAL;
-+	}
-+
-+	/* Setup PageFormat */
-+	while (caps->spare_size[i] != snfi_nand->spare_per_sector) {
-+		i++;
-+		if (i == (caps->num_spare_size - 1)) {
-+			dev_err(snfi->dev, "invalid spare size %d\n",
-+				snfi_nand->spare_per_sector);
-+			return -EINVAL;
-+		}
-+	}
-+
-+	fmt |= i << caps->pageformat_spare_shift;
-+	fmt |= caps->nand_fdm_size << PAGEFMT_FDM_SHIFT;
-+	fmt |= caps->nand_fdm_ecc_size << PAGEFMT_FDM_ECC_SHIFT;
-+	writel(fmt, snfi->regs + NFI_PAGEFMT);
-+
-+	snfi->ecc_cfg.len = caps->nand_sec_size + caps->nand_fdm_ecc_size;
-+
-+	mtk_snfi_set_bad_mark_ctl(&snfi_nand->bad_mark, mem);
-+
-+	return 0;
-+}
-+
-+static int mtk_snfi_read_from_cache(struct spi_mem *mem,
-+				    const struct spi_mem_op *op, int oob_on)
-+{
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	u32 sectors = mtd->writesize / snfi->caps->nand_sec_size;
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+	u32 reg, len, col_addr = 0;
-+	int dummy_cycle, ret;
-+	dma_addr_t dma_addr;
-+
-+	len = sectors * (snfi->caps->nand_sec_size
-+	      + snfi_nand->spare_per_sector);
-+
-+	dma_addr = dma_map_single(snfi->dev, snfi->buffer,
-+				  len, DMA_FROM_DEVICE);
-+	ret = dma_mapping_error(snfi->dev, dma_addr);
-+	if (ret) {
-+		dev_err(snfi->dev, "dma mapping error\n");
-+		return -EINVAL;
-+	}
-+
-+	/* set Read cache command and dummy cycle */
-+	dummy_cycle = (op->dummy.nbytes << 3) >> (ffs(op->dummy.buswidth) - 1);
-+	reg = ((op->cmd.opcode & RD_CMD_MASK) |
-+	       (dummy_cycle << RD_DUMMY_SHIFT));
-+	writel(reg, snfi->regs + SNFI_RD_CTL2);
-+
-+	writel((col_addr & RD_ADDR_MASK), snfi->regs + SNFI_RD_CTL3);
-+
-+	reg = readl(snfi->regs + SNFI_MISC_CTL);
-+	reg |= RD_CUSTOM_EN;
-+	reg &= ~(RD_MODE_MASK | WR_X4_EN);
-+
-+	/* set data and addr buswidth */
-+	if (op->data.buswidth == 4)
-+		reg |= RD_MODE_X4;
-+	else if (op->data.buswidth == 2)
-+		reg |= RD_MODE_X2;
-+
-+	if (op->addr.buswidth == 4 || op->addr.buswidth == 2)
-+		reg |= RD_QDUAL_IO;
-+	writel(reg, snfi->regs + SNFI_MISC_CTL);
-+
-+	writel(len, snfi->regs + SNFI_MISC_CTL2);
-+	writew(sectors << CON_SEC_SHIFT, snfi->regs + NFI_CON);
-+	reg = readw(snfi->regs + NFI_CNFG);
-+	reg |= CNFG_READ_EN | CNFG_DMA_BURST_EN | CNFG_DMA | CNFG_OP_CUST;
-+
-+	if (!oob_on) {
-+		reg |= CNFG_AUTO_FMT_EN | CNFG_HW_ECC_EN;
-+		writew(reg, snfi->regs + NFI_CNFG);
-+
-+		snfi->ecc_cfg.mode = ECC_NFI_MODE;
-+		snfi->ecc_cfg.sectors = sectors;
-+		snfi->ecc_cfg.op = ECC_DECODE;
-+		ret = mtk_ecc_enable(snfi->ecc, &snfi->ecc_cfg);
-+		if (ret) {
-+			dev_err(snfi->dev, "ecc enable failed\n");
-+			/* clear NFI_CNFG */
-+			reg &= ~(CNFG_READ_EN | CNFG_DMA_BURST_EN | CNFG_DMA |
-+				CNFG_AUTO_FMT_EN | CNFG_HW_ECC_EN);
-+			writew(reg, snfi->regs + NFI_CNFG);
-+			goto out;
-+		}
-+	} else {
-+		writew(reg, snfi->regs + NFI_CNFG);
-+	}
-+
-+	writel(lower_32_bits(dma_addr), snfi->regs + NFI_STRADDR);
-+	readw(snfi->regs + NFI_INTR_STA);
-+	writew(INTR_AHB_DONE_EN, snfi->regs + NFI_INTR_EN);
-+
-+	init_completion(&snfi->done);
-+
-+	/* set dummy command to trigger NFI enter SPI mode */
-+	writew(NAND_CMD_DUMMYREAD, snfi->regs + NFI_CMD);
-+	reg = readl(snfi->regs + NFI_CON) | CON_BRD;
-+	writew(reg, snfi->regs + NFI_CON);
-+
-+	ret = wait_for_completion_timeout(&snfi->done, msecs_to_jiffies(500));
-+	if (!ret) {
-+		dev_err(snfi->dev, "read ahb done timeout\n");
-+		writew(0, snfi->regs + NFI_INTR_EN);
-+		ret = -ETIMEDOUT;
-+		goto out;
-+	}
-+
-+	ret = readl_poll_timeout_atomic(snfi->regs + NFI_BYTELEN, reg,
-+					ADDRCNTR_SEC(reg) >= sectors, 10,
-+					MTK_TIMEOUT);
-+	if (ret < 0) {
-+		dev_err(snfi->dev, "polling read byte len timeout\n");
-+		ret = -EIO;
-+	} else {
-+		if (!oob_on) {
-+			ret = mtk_ecc_wait_done(snfi->ecc, ECC_DECODE);
-+			if (ret) {
-+				dev_warn(snfi->dev, "wait ecc done timeout\n");
-+			} else {
-+				mtk_snfi_update_ecc_stats(mem, snfi->buffer,
-+							  sectors);
-+				mtk_snfi_read_fdm_data(mem, sectors);
-+			}
-+		}
-+	}
-+
-+	if (oob_on)
-+		goto out;
-+
-+	mtk_ecc_disable(snfi->ecc);
-+out:
-+	dma_unmap_single(snfi->dev, dma_addr, len, DMA_FROM_DEVICE);
-+	writel(0, snfi->regs + NFI_CON);
-+	writel(0, snfi->regs + NFI_CNFG);
-+	reg = readl(snfi->regs + SNFI_MISC_CTL);
-+	reg &= ~RD_CUSTOM_EN;
-+	writel(reg, snfi->regs + SNFI_MISC_CTL);
-+
-+	return ret;
-+}
-+
-+static int mtk_snfi_write_to_cache(struct spi_mem *mem,
-+				   const struct spi_mem_op *op,
-+				   int oob_on)
-+{
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	u32 sectors = mtd->writesize / snfi->caps->nand_sec_size;
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+	u32 reg, len, col_addr = 0;
-+	dma_addr_t dma_addr;
-+	int ret;
-+
-+	len = sectors * (snfi->caps->nand_sec_size
-+	      + snfi_nand->spare_per_sector);
-+
-+	dma_addr = dma_map_single(snfi->dev, snfi->buffer, len,
-+				  DMA_TO_DEVICE);
-+	ret = dma_mapping_error(snfi->dev, dma_addr);
-+	if (ret) {
-+		dev_err(snfi->dev, "dma mapping error\n");
-+		return -EINVAL;
-+	}
-+
-+	/* set program load cmd and address */
-+	reg = (op->cmd.opcode << WR_LOAD_CMD_SHIFT);
-+	writel(reg, snfi->regs + SNFI_PG_CTL1);
-+	writel(col_addr & WR_LOAD_ADDR_MASK, snfi->regs + SNFI_PG_CTL2);
-+
-+	reg = readl(snfi->regs + SNFI_MISC_CTL);
-+	reg |= WR_CUSTOM_EN;
-+	reg &= ~(RD_MODE_MASK | WR_X4_EN);
-+
-+	if (op->data.buswidth == 4)
-+		reg |= WR_X4_EN;
-+	writel(reg, snfi->regs + SNFI_MISC_CTL);
-+
-+	writel(len << WR_LEN_SHIFT, snfi->regs + SNFI_MISC_CTL2);
-+	writew(sectors << CON_SEC_SHIFT, snfi->regs + NFI_CON);
-+
-+	reg = readw(snfi->regs + NFI_CNFG);
-+	reg &= ~(CNFG_READ_EN | CNFG_BYTE_RW);
-+	reg |= CNFG_DMA | CNFG_DMA_BURST_EN | CNFG_OP_PROGRAM;
-+
-+	if (!oob_on) {
-+		reg |= CNFG_AUTO_FMT_EN | CNFG_HW_ECC_EN;
-+		writew(reg, snfi->regs + NFI_CNFG);
-+
-+		snfi->ecc_cfg.mode = ECC_NFI_MODE;
-+		snfi->ecc_cfg.op = ECC_ENCODE;
-+		ret = mtk_ecc_enable(snfi->ecc, &snfi->ecc_cfg);
-+		if (ret) {
-+			dev_err(snfi->dev, "ecc enable failed\n");
-+			/* clear NFI_CNFG */
-+			reg &= ~(CNFG_DMA_BURST_EN | CNFG_DMA |
-+					CNFG_AUTO_FMT_EN | CNFG_HW_ECC_EN);
-+			writew(reg, snfi->regs + NFI_CNFG);
-+			dma_unmap_single(snfi->dev, dma_addr, len,
-+					 DMA_FROM_DEVICE);
-+			goto out;
-+		}
-+		/* write OOB into the FDM registers (OOB area in MTK NAND) */
-+		mtk_snfi_write_fdm_data(mem, sectors);
-+	} else {
-+		writew(reg, snfi->regs + NFI_CNFG);
-+	}
-+	writel(lower_32_bits(dma_addr), snfi->regs + NFI_STRADDR);
-+	readw(snfi->regs + NFI_INTR_STA);
-+	writew(INTR_AHB_DONE_EN, snfi->regs + NFI_INTR_EN);
-+
-+	init_completion(&snfi->done);
-+
-+	/* set dummy command to trigger NFI enter SPI mode */
-+	writew(NAND_CMD_DUMMYPROG, snfi->regs + NFI_CMD);
-+	reg = readl(snfi->regs + NFI_CON) | CON_BWR;
-+	writew(reg, snfi->regs + NFI_CON);
-+
-+	ret = wait_for_completion_timeout(&snfi->done, msecs_to_jiffies(500));
-+	if (!ret) {
-+		dev_err(snfi->dev, "custom program done timeout\n");
-+		writew(0, snfi->regs + NFI_INTR_EN);
-+		ret = -ETIMEDOUT;
-+		goto ecc_disable;
-+	}
-+
-+	ret = readl_poll_timeout_atomic(snfi->regs + NFI_ADDRCNTR, reg,
-+					ADDRCNTR_SEC(reg) >= sectors,
-+					10, MTK_TIMEOUT);
-+	if (ret)
-+		dev_err(snfi->dev, "hwecc write timeout\n");
-+
-+ecc_disable:
-+	mtk_ecc_disable(snfi->ecc);
-+
-+out:
-+	dma_unmap_single(snfi->dev, dma_addr, len, DMA_TO_DEVICE);
-+	writel(0, snfi->regs + NFI_CON);
-+	writel(0, snfi->regs + NFI_CNFG);
-+	reg = readl(snfi->regs + SNFI_MISC_CTL);
-+	reg &= ~WR_CUSTOM_EN;
-+	writel(reg, snfi->regs + SNFI_MISC_CTL);
-+
-+	return ret;
-+}
-+
-+static int mtk_snfi_read(struct spi_mem *mem,
-+			 const struct spi_mem_op *op)
-+{
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+	u32 col_addr = op->addr.val;
-+	int i, ret, sectors, oob_on = false;
-+
-+	if (col_addr == mtd->writesize)
-+		oob_on = true;
-+
-+	ret = mtk_snfi_read_from_cache(mem, op, oob_on);
-+	if (ret) {
-+		dev_warn(snfi->dev, "read from cache fail\n");
-+		return ret;
-+	}
-+
-+	sectors = mtd->writesize / snfi->caps->nand_sec_size;
-+	for (i = 0; i < sectors; i++) {
-+		if (oob_on)
-+			memcpy(oob_ptr(mem, i),
-+			       mtk_oob_ptr(mem, snfi->buffer, i),
-+			       snfi->caps->nand_fdm_size);
-+
-+		if (i == snfi_nand->bad_mark.sec && snfi->caps->bad_mark_swap)
-+			snfi_nand->bad_mark.bm_swap(mem, snfi->buffer,
-+							oob_on);
-+	}
-+
-+	if (!oob_on)
-+		memcpy(spinand->databuf, snfi->buffer, mtd->writesize);
-+
-+	return ret;
-+}
-+
-+static int mtk_snfi_write(struct spi_mem *mem,
-+			  const struct spi_mem_op *op)
-+{
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	struct mtk_snfi_nand_chip *snfi_nand = &snfi->snfi_nand;
-+	u32 ret, i, sectors, col_addr = op->addr.val;
-+	int oob_on = false;
-+
-+	if (col_addr == mtd->writesize)
-+		oob_on = true;
-+
-+	sectors = mtd->writesize / snfi->caps->nand_sec_size;
-+	memset(snfi->buffer, 0xff, mtd->writesize + mtd->oobsize);
-+
-+	if (!oob_on)
-+		memcpy(snfi->buffer, spinand->databuf, mtd->writesize);
-+
-+	for (i = 0; i < sectors; i++) {
-+		if (i == snfi_nand->bad_mark.sec && snfi->caps->bad_mark_swap)
-+			snfi_nand->bad_mark.bm_swap(mem, snfi->buffer, oob_on);
-+
-+		if (oob_on)
-+			memcpy(mtk_oob_ptr(mem, snfi->buffer, i),
-+			       oob_ptr(mem, i),
-+			       snfi->caps->nand_fdm_size);
-+	}
-+
-+	ret = mtk_snfi_write_to_cache(mem, op, oob_on);
-+	if (ret)
-+		dev_warn(snfi->dev, "write to cache fail\n");
-+
-+	return ret;
-+}
-+
-+static int mtk_snfi_command_exec(struct mtk_snfi *snfi,
-+				 const u8 *txbuf, u8 *rxbuf,
-+				 const u32 txlen, const u32 rxlen)
-+{
-+	u32 tmp, i, j, reg, m;
-+	u8 *p_tmp = (u8 *)(&tmp);
-+	int ret = 0;
-+
-+	/* Moving tx data to NFI_SPI GPRAM */
-+	for (i = 0, m = 0; i < txlen; ) {
-+		for (j = 0, tmp = 0; i < txlen && j < 4; i++, j++)
-+			p_tmp[j] = txbuf[i];
-+
-+		writel(tmp, snfi->regs + SNFI_GPRAM_DATA + m);
-+		m += 4;
-+	}
-+
-+	writel(txlen, snfi->regs + SNFI_MAC_OUTL);
-+	writel(rxlen, snfi->regs + SNFI_MAC_INL);
-+	ret = mtk_snfi_mac_op(snfi);
-+	if (ret)
-+		return ret;
-+
-+	/* For NULL input data, this loop will be skipped */
-+	if (rxlen)
-+		for (i = 0, m = 0; i < rxlen; ) {
-+			reg = readl(snfi->regs +
-+					    SNFI_GPRAM_DATA + m);
-+			for (j = 0; i < rxlen && j < 4; i++, j++, rxbuf++) {
-+				if (m == 0 && i == 0)
-+					j = i + txlen;
-+				*rxbuf = (reg >> (j * 8)) & 0xFF;
-+			}
-+			m += 4;
-+		}
-+
-+	return ret;
-+}
-+
-+/*
-+ * mtk_snfi_exec_op - to process command/data to send to the
-+ * SPI NAND by mtk controller
-+ */
-+static int mtk_snfi_exec_op(struct spi_mem *mem,
-+			    const struct spi_mem_op *op)
-+
-+{
-+	struct mtk_snfi *snfi = spi_controller_get_devdata(mem->spi->master);
-+	struct spinand_device *spinand = spi_mem_get_drvdata(mem);
-+	struct mtd_info *mtd = spinand_to_mtd(spinand);
-+	struct nand_device *nand = mtd_to_nanddev(mtd);
-+	const struct spi_mem_op *read_cache;
-+	const struct spi_mem_op *write_cache;
-+	const struct spi_mem_op *update_cache;
-+	u32 tmpbufsize, txlen = 0, rxlen = 0;
-+	u8 *txbuf, *rxbuf = NULL, *buf;
-+	int i, ret = 0;
-+	
-+	ret = mtk_snfi_reset(snfi);
-+	if (ret) {
-+		dev_warn(snfi->dev, "reset spi memory controller fail\n");
-+		return ret;
-+	}
-+
-+	/*if bbt initial, framework have detect nand information */
-+	if (nand->bbt.cache) {
-+		read_cache = spinand->op_templates.read_cache;
-+		write_cache = spinand->op_templates.write_cache;
-+		update_cache = spinand->op_templates.update_cache;
-+
-+		ret = mtk_snfi_hw_runtime_config(mem);
-+		if (ret)
-+			return ret;
-+
-+		/* For Read/Write with cache, Erase use framework flow */
-+		if (op->cmd.opcode == read_cache->cmd.opcode) {
-+			ret = mtk_snfi_read(mem, op);
-+			if (ret)
-+				dev_warn(snfi->dev, "snfi read fail\n");
-+			
-+			return ret;
-+		} else if ((op->cmd.opcode == write_cache->cmd.opcode)
-+			       	|| (op->cmd.opcode == update_cache->cmd.opcode)) {
-+			ret = mtk_snfi_write(mem, op);
-+			if (ret)
-+				dev_warn(snfi->dev, "snfi write fail\n");
-+			
-+			return ret;
-+		}
-+	}
-+
-+	tmpbufsize = sizeof(op->cmd.opcode) + op->addr.nbytes +
-+		     op->dummy.nbytes + op->data.nbytes;
-+
-+	txbuf = kzalloc(tmpbufsize, GFP_KERNEL);
-+	if (!txbuf)
-+		return -ENOMEM;
-+
-+	txbuf[txlen++] = op->cmd.opcode;
-+
-+	if (op->addr.nbytes)
-+		for (i = 0; i < op->addr.nbytes; i++)
-+			txbuf[txlen++] = op->addr.val >>
-+					(8 * (op->addr.nbytes - i - 1));
-+
-+	txlen += op->dummy.nbytes;
-+
-+	if (op->data.dir == SPI_MEM_DATA_OUT)
-+		for (i = 0; i < op->data.nbytes; i++) {
-+			buf = (u8 *)op->data.buf.out;
-+			txbuf[txlen++] = buf[i];
-+		}
-+
-+	if (op->data.dir == SPI_MEM_DATA_IN) {
-+		rxbuf = (u8 *)op->data.buf.in;
-+		rxlen += op->data.nbytes;
-+	}
-+
-+	ret = mtk_snfi_command_exec(snfi, txbuf, rxbuf, txlen, rxlen);
-+	kfree(txbuf);
-+
-+	return ret;
-+}
-+
-+static int mtk_snfi_init(struct mtk_snfi *snfi)
-+{
-+	int ret;
-+
-+	/* Reset the state machine and data FIFO */
-+	ret = mtk_snfi_reset(snfi);
-+	if (ret) {
-+		dev_warn(snfi->dev, "MTK reset controller fail\n");
-+		return ret;
-+	}
-+
-+	snfi->buffer = devm_kzalloc(snfi->dev, 4096 + 256, GFP_KERNEL);
-+	if (!snfi->buffer)
-+		return  -ENOMEM;
-+
-+	/* Clear interrupt, read clear. */
-+	readw(snfi->regs + NFI_INTR_STA);
-+	writew(0, snfi->regs + NFI_INTR_EN);
-+
-+	writel(0, snfi->regs + NFI_CON);
-+	writel(0, snfi->regs + NFI_CNFG);
-+
-+	/* Change to NFI_SPI mode. */
-+	writel(SNFI_MODE_EN, snfi->regs + SNFI_CNFG);
-+
-+	return 0;
-+}
-+
-+static int mtk_snfi_check_buswidth(u8 width)
-+{
-+	switch (width) {
-+	case 1:
-+	case 2:
-+	case 4:
-+		return 0;
-+
-+	default:
-+		break;
-+	}
-+
-+	return -ENOTSUPP;
-+}
-+
-+static bool mtk_snfi_supports_op(struct spi_mem *mem,
-+				 const struct spi_mem_op *op)
-+{
-+	int ret = 0;
-+
-+	/* For MTK Spi Nand controller, cmd buswidth just support 1 bit*/
-+	if (op->cmd.buswidth != 1)
-+		ret = -ENOTSUPP;
-+
-+	if (op->addr.nbytes)
-+		ret |= mtk_snfi_check_buswidth(op->addr.buswidth);
-+
-+	if (op->dummy.nbytes)
-+		ret |= mtk_snfi_check_buswidth(op->dummy.buswidth);
-+
-+	if (op->data.nbytes)
-+		ret |= mtk_snfi_check_buswidth(op->data.buswidth);
-+
-+	if (ret)
-+		return false;
-+
-+	return true;
-+}
-+
-+static const struct spi_controller_mem_ops mtk_snfi_ops = {
-+	.supports_op = mtk_snfi_supports_op,
-+	.exec_op = mtk_snfi_exec_op,
-+};
-+
-+static const struct mtk_snfi_caps snfi_mt7622 = {
-+	.spare_size = spare_size_mt7622,
-+	.num_spare_size = 4,
-+	.nand_sec_size = 512,
-+	.nand_fdm_size = 8,
-+	.nand_fdm_ecc_size = 1,
-+	.ecc_parity_bits = 13,
-+	.pageformat_spare_shift = 4,
-+	.bad_mark_swap = 0,
-+};
-+
-+static const struct mtk_snfi_caps snfi_mt7629 = {
-+	.spare_size = spare_size_mt7622,
-+	.num_spare_size = 4,
-+	.nand_sec_size = 512,
-+	.nand_fdm_size = 8,
-+	.nand_fdm_ecc_size = 1,
-+	.ecc_parity_bits = 13,
-+	.pageformat_spare_shift = 4,
-+	.bad_mark_swap = 1,
-+};
-+
-+static const struct of_device_id mtk_snfi_id_table[] = {
-+	{ .compatible = "mediatek,mt7622-snfi", .data = &snfi_mt7622, },
-+	{ .compatible = "mediatek,mt7629-snfi", .data = &snfi_mt7629, },
-+	{  /* sentinel */ }
-+};
-+
-+static int mtk_snfi_probe(struct platform_device *pdev)
-+{
-+	struct device *dev = &pdev->dev;
-+	struct device_node *np = dev->of_node;
-+	struct spi_controller *ctlr;
-+	struct mtk_snfi *snfi;
-+	struct resource *res;
-+	int ret = 0, irq;
-+
-+	ctlr = spi_alloc_master(&pdev->dev, sizeof(*snfi));
-+	if (!ctlr)
-+		return -ENOMEM;
-+
-+	snfi = spi_controller_get_devdata(ctlr);
-+	snfi->caps = of_device_get_match_data(dev);
-+	snfi->dev = dev;
-+
-+	snfi->ecc = of_mtk_ecc_get(np);
-+	if (IS_ERR_OR_NULL(snfi->ecc))
-+		goto err_put_master;
-+
-+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+	snfi->regs = devm_ioremap_resource(dev, res);
-+	if (IS_ERR(snfi->regs)) {
-+		ret = PTR_ERR(snfi->regs);
-+		goto release_ecc;
-+	}
-+
-+	/* find the clocks */
-+	snfi->clk.nfi_clk = devm_clk_get(dev, "nfi_clk");
-+	if (IS_ERR(snfi->clk.nfi_clk)) {
-+		dev_err(dev, "no nfi clk\n");
-+		ret = PTR_ERR(snfi->clk.nfi_clk);
-+		goto release_ecc;
-+	}
-+
-+	snfi->clk.spi_clk = devm_clk_get(dev, "spi_clk");
-+	if (IS_ERR(snfi->clk.spi_clk)) {
-+		dev_err(dev, "no spi clk\n");
-+		ret = PTR_ERR(snfi->clk.spi_clk);
-+		goto release_ecc;
-+	}
-+
-+	ret = mtk_snfi_enable_clk(dev, &snfi->clk);
-+	if (ret)
-+		goto release_ecc;
-+
-+	/* find the irq */
-+	irq = platform_get_irq(pdev, 0);
-+	if (irq < 0) {
-+		dev_err(dev, "no snfi irq resource\n");
-+		ret = -EINVAL;
-+		goto clk_disable;
-+	}
-+
-+	ret = devm_request_irq(dev, irq, mtk_snfi_irq, 0, "mtk-snfi", snfi);
-+	if (ret) {
-+		dev_err(dev, "failed to request snfi irq\n");
-+		goto clk_disable;
-+	}
-+
-+	ret = dma_set_mask(dev, DMA_BIT_MASK(32));
-+	if (ret) {
-+		dev_err(dev, "failed to set dma mask\n");
-+		goto clk_disable;
-+	}
-+
-+	ctlr->dev.of_node = np;
-+	ctlr->mem_ops = &mtk_snfi_ops;
-+
-+	platform_set_drvdata(pdev, snfi);
-+	ret = mtk_snfi_init(snfi);
-+	if (ret) {
-+		dev_err(dev, "failed to init snfi\n");
-+		goto clk_disable;
-+	}
-+
-+	ret = devm_spi_register_master(dev, ctlr);
-+	if (ret)
-+		goto clk_disable;
-+
-+	return 0;
-+
-+clk_disable:
-+	mtk_snfi_disable_clk(&snfi->clk);
-+
-+release_ecc:
-+	mtk_ecc_release(snfi->ecc);
-+
-+err_put_master:
-+	spi_master_put(ctlr);
-+
-+	dev_err(dev, "MediaTek SPI NAND interface probe failed %d\n", ret);
-+	return ret;
-+}
-+
-+static int mtk_snfi_remove(struct platform_device *pdev)
-+{
-+	struct mtk_snfi *snfi = platform_get_drvdata(pdev);
-+
-+	mtk_snfi_disable_clk(&snfi->clk);
-+
-+	return 0;
-+}
-+
-+static int mtk_snfi_suspend(struct platform_device *pdev, pm_message_t state)
-+{
-+	struct mtk_snfi *snfi = platform_get_drvdata(pdev);
-+
-+	mtk_snfi_disable_clk(&snfi->clk);
-+
-+	return 0;
-+}
-+
-+static int mtk_snfi_resume(struct platform_device *pdev)
-+{
-+	struct device *dev = &pdev->dev;
-+	struct mtk_snfi *snfi = dev_get_drvdata(dev);
-+	int ret;
-+
-+	ret = mtk_snfi_enable_clk(dev, &snfi->clk);
-+	if (ret)
-+		return ret;
-+
-+	ret = mtk_snfi_init(snfi);
-+	if (ret)
-+		dev_err(dev, "failed to init snfi controller\n");
-+
-+	return ret;
-+}
-+
-+static struct platform_driver mtk_snfi_driver = {
-+	.driver = {
-+		.name	= "mtk-snfi",
-+		.of_match_table = mtk_snfi_id_table,
-+	},
-+	.probe		= mtk_snfi_probe,
-+	.remove		= mtk_snfi_remove,
-+	.suspend	= mtk_snfi_suspend,
-+	.resume		= mtk_snfi_resume,
-+};
-+
-+module_platform_driver(mtk_snfi_driver);
-+
-+MODULE_LICENSE("GPL v2");
-+MODULE_AUTHOR("Xiangsheng Hou <xiangsheng.hou@mediatek.com>");
-+MODULE_DESCRIPTION("Mediatek SPI Memory Interface Driver");
diff --git a/target/linux/mediatek/patches-5.4/0307-dts-mt7629-add-snand-support.patch b/target/linux/mediatek/patches-5.4/0307-dts-mt7629-add-snand-support.patch
deleted file mode 100644
index 233face4c5..0000000000
--- a/target/linux/mediatek/patches-5.4/0307-dts-mt7629-add-snand-support.patch
+++ /dev/null
@@ -1,97 +0,0 @@
-From c813fbe806257c574240770ef716fbee19f7dbfa Mon Sep 17 00:00:00 2001
-From: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
-Date: Thu, 6 Jun 2019 16:29:04 +0800
-Subject: [PATCH] spi: spi-mem: Mediatek: Add SPI Nand support for MT7629
-
-Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
----
- arch/arm/boot/dts/mt7629-rfb.dts | 45 ++++++++++++++++++++++++++++++++
- arch/arm/boot/dts/mt7629.dtsi    | 22 ++++++++++++++++
- 3 files changed, 79 insertions(+)
-
---- a/arch/arm/boot/dts/mt7629.dtsi
-+++ b/arch/arm/boot/dts/mt7629.dtsi
-@@ -258,6 +258,28 @@
- 			status = "disabled";
- 		};
- 
-+		bch: ecc@1100e000 {
-+			compatible = "mediatek,mt7622-ecc";
-+			reg = <0x1100e000 0x1000>;
-+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_LOW>;
-+			clocks = <&pericfg CLK_PERI_NFIECC_PD>;
-+			clock-names = "nfiecc_clk";
-+			status = "disabled";
-+		};
-+
-+		snfi: spi@1100d000 {
-+			compatible = "mediatek,mt7629-snfi";
-+			reg = <0x1100d000 0x1000>;
-+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
-+			clocks = <&pericfg CLK_PERI_NFI_PD>,
-+				 <&pericfg CLK_PERI_SNFI_PD>;
-+			clock-names = "nfi_clk", "spi_clk";
-+			ecc-engine = <&bch>;
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+			status = "disabled";
-+		};
-+
- 		spi: spi@1100a000 {
- 			compatible = "mediatek,mt7629-spi",
- 				     "mediatek,mt7622-spi";
---- a/arch/arm/boot/dts/mt7629-rfb.dts
-+++ b/arch/arm/boot/dts/mt7629-rfb.dts
-@@ -281,6 +281,52 @@
- 	};
- };
- 
-+&bch {
-+	status = "okay";
-+};
-+
-+&snfi {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&serial_nand_pins>;
-+	status = "okay";
-+
-+	spi_nand@0 {
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		compatible = "spi-nand";
-+		spi-max-frequency = <104000000>;
-+		reg = <0>;
-+
-+		partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		partition@0 {
-+			label = "Bootloader";
-+			reg = <0x00000 0x0100000>;
-+			read-only;
-+		};
-+
-+		partition@100000 {
-+			label = "Config";
-+			reg = <0x100000 0x0040000>;
-+		};
-+
-+		partition@140000 {
-+			label = "factory";
-+			reg = <0x140000 0x0080000>;
-+		};
-+
-+		partition@1c0000 {
-+			label = "firmware";
-+			reg = <0x1c0000 0x1000000>;
-+		};
-+
-+		};
-+	};
-+};
-+
- &spi {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&spi_pins>;
diff --git a/target/linux/mediatek/patches-5.4/0308-dts-mt7622-add-snand-support.patch b/target/linux/mediatek/patches-5.4/0308-dts-mt7622-add-snand-support.patch
deleted file mode 100644
index b287780d6c..0000000000
--- a/target/linux/mediatek/patches-5.4/0308-dts-mt7622-add-snand-support.patch
+++ /dev/null
@@ -1,96 +0,0 @@
---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-@@ -554,6 +554,19 @@
- 		status = "disabled";
- 	};
- 
-+	snfi: spi@1100d000 {
-+		compatible = "mediatek,mt7622-snfi";
-+		reg = <0 0x1100d000 0 0x1000>;
-+		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
-+		clocks = <&pericfg CLK_PERI_NFI_PD>,
-+			 <&pericfg CLK_PERI_SNFI_PD>;
-+		clock-names = "nfi_clk", "spi_clk";
-+		ecc-engine = <&bch>;
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		status = "disabled";
-+	};
-+
- 	nor_flash: spi@11014000 {
- 		compatible = "mediatek,mt7622-nor",
- 			     "mediatek,mt8173-nor";
---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-@@ -99,7 +99,7 @@
- };
- 
- &bch {
--	status = "disabled";
-+	status = "okay";
- };
- 
- &btif {
-@@ -551,6 +551,62 @@
- 	status = "disable";
- };
- 
-+&snfi {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&serial_nand_pins>;
-+	status = "okay";
-+
-+	spi_nand@0 {
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		compatible = "spi-nand";
-+		spi-max-frequency = <104000000>;
-+		reg = <0>;
-+
-+		partitions {
-+			compatible = "fixed-partitions";
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+
-+			partition@0 {
-+				label = "Preloader";
-+				reg = <0x00000 0x0080000>;
-+				read-only;
-+			};
-+
-+			partition@80000 {
-+				label = "ATF";
-+				reg = <0x80000 0x0040000>;
-+			};
-+
-+			partition@c0000 {
-+				label = "Bootloader";
-+				reg = <0xc0000 0x0080000>;
-+			};
-+
-+			partition@140000 {
-+				label = "Config";
-+				reg = <0x140000 0x0080000>;
-+			};
-+
-+			partition@1c0000 {
-+				label = "Factory";
-+				reg = <0x1c0000 0x0040000>;
-+			};
-+
-+			partition@200000 {
-+				label = "firmware";
-+				reg = <0x200000 0x2000000>;
-+			};
-+
-+			partition@2200000 {
-+				label = "User_data";
-+				reg = <0x2200000 0x4000000>;
-+			};
-+		};
-+	};
-+};
-+
- &spi0 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&spic0_pins>;
diff --git a/target/linux/mediatek/patches-5.4/0310-dts-add-wmac-support-for-mt7622-rfb1.patch b/target/linux/mediatek/patches-5.4/0310-dts-add-wmac-support-for-mt7622-rfb1.patch
deleted file mode 100644
index 84aed89752..0000000000
--- a/target/linux/mediatek/patches-5.4/0310-dts-add-wmac-support-for-mt7622-rfb1.patch
+++ /dev/null
@@ -1,40 +0,0 @@
---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-@@ -716,6 +716,17 @@
- 		status = "disabled";
- 	};
- 
-+	wmac: wmac@18000000 {
-+		compatible = "mediatek,mt7622-wmac";
-+		reg = <0 0x18000000 0 0x100000>;
-+		interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_LOW>;
-+
-+		mediatek,infracfg = <&infracfg>;
-+		status = "disabled";
-+
-+		power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>;
-+	};
-+
- 	ssusbsys: ssusbsys@1a000000 {
- 		compatible = "mediatek,mt7622-ssusbsys",
- 			     "syscon";
---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-@@ -589,7 +589,7 @@
- 				reg = <0x140000 0x0080000>;
- 			};
- 
--			partition@1c0000 {
-+			factory: partition@1c0000 {
- 				label = "Factory";
- 				reg = <0x1c0000 0x0040000>;
- 			};
-@@ -646,3 +646,8 @@
- 	pinctrl-0 = <&watchdog_pins>;
- 	status = "okay";
- };
-+
-+&wmac {
-+	mediatek,mtd-eeprom = <&factory 0x0000>;
-+	status = "okay";
-+};
diff --git a/target/linux/mediatek/patches-5.4/0310-mtk-bmt-support.patch b/target/linux/mediatek/patches-5.4/0310-mtk-bmt-support.patch
deleted file mode 100644
index 4cef9f9d5e..0000000000
--- a/target/linux/mediatek/patches-5.4/0310-mtk-bmt-support.patch
+++ /dev/null
@@ -1,837 +0,0 @@
---- a/drivers/mtd/nand/Kconfig
-+++ b/drivers/mtd/nand/Kconfig
-@@ -5,3 +5,7 @@ config MTD_NAND_CORE
- source "drivers/mtd/nand/onenand/Kconfig"
- source "drivers/mtd/nand/raw/Kconfig"
- source "drivers/mtd/nand/spi/Kconfig"
-+
-+config MTD_NAND_MTK_BMT
-+	bool "Support MediaTek NAND Bad-block Management Table"
-+	default n
---- a/drivers/mtd/nand/Makefile
-+++ b/drivers/mtd/nand/Makefile
-@@ -2,6 +2,7 @@
- 
- nandcore-objs := core.o bbt.o
- obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o
-+obj-$(CONFIG_MTD_NAND_MTK_BMT)	+= mtk_bmt.o
- 
- obj-y	+= onenand/
- obj-y	+= raw/
---- /dev/null
-+++ b/drivers/mtd/nand/mtk_bmt.c
-@@ -0,0 +1,766 @@
-+/*
-+ * Copyright (c) 2017 MediaTek Inc.
-+ * Author: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
-+ * Copyright (c) 2020 Felix Fietkau <nbd@nbd.name>
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ */
-+
-+#include <linux/slab.h>
-+#include <linux/gfp.h>
-+#include <linux/kernel.h>
-+#include <linux/of.h>
-+#include <linux/mtd/nand.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/mtd/mtk_bmt.h>
-+#include <linux/module.h>
-+#include <linux/debugfs.h>
-+
-+#define MAIN_SIGNATURE_OFFSET   0
-+#define OOB_SIGNATURE_OFFSET    1
-+#define BBPOOL_RATIO		2
-+
-+#define BBT_LOG(fmt, ...) pr_debug("[BBT][%s|%d] "fmt"\n", __func__, __LINE__, ##__VA_ARGS__)
-+
-+/* Maximum 8k blocks */
-+#define BB_TABLE_MAX	0x2000U
-+#define BMT_TABLE_MAX	(BB_TABLE_MAX * BBPOOL_RATIO / 100)
-+#define BMT_TBL_DEF_VAL	0x0
-+
-+/*
-+ * Burner Bad Block Table
-+ * --------- Only support SLC Nand Chips!!!!!!!!!!! ----------
-+ */
-+
-+struct bbbt {
-+	char signature[3];
-+	/* This version is used to distinguish the legacy and new algorithm */
-+#define BBMT_VERSION		2
-+	unsigned char version;
-+	/* Below 2 tables will be written in SLC */
-+	u16 bb_tbl[BB_TABLE_MAX];
-+	struct bbmt {
-+		u16 block;
-+#define NO_MAPPED		0
-+#define NORMAL_MAPPED	1
-+#define BMT_MAPPED		2
-+		u16 mapped;
-+	} bmt_tbl[BMT_TABLE_MAX];
-+};
-+
-+static struct bmt_desc {
-+	struct mtd_info *mtd;
-+
-+	int (*_read_oob) (struct mtd_info *mtd, loff_t from,
-+			  struct mtd_oob_ops *ops);
-+	int (*_write_oob) (struct mtd_info *mtd, loff_t to,
-+			   struct mtd_oob_ops *ops);
-+	const struct nand_ops *nand_ops;
-+
-+	struct bbbt *bbt;
-+
-+	struct dentry *debugfs_dir;
-+
-+	u32 pg_size;
-+	u32 blk_size;
-+	u16 pg_shift;
-+	u16 blk_shift;
-+	/* bbt logical address */
-+	u16 pool_lba;
-+	/* bbt physical address */
-+	u16 pool_pba;
-+	/* Maximum count of bad blocks that the vendor guaranteed */
-+	u16 bb_max;
-+	/* Total blocks of the Nand Chip */
-+	u16 total_blks;
-+	/* The block(n) BMT is located at (bmt_tbl[n]) */
-+	u16 bmt_blk_idx;
-+	/* How many pages needs to store 'struct bbbt' */
-+	u32 bmt_pgs;
-+
-+	/* to compensate for driver level remapping */
-+	u8 oob_offset;
-+} bmtd = {0};
-+
-+static unsigned char *nand_bbt_buf;
-+static unsigned char *nand_data_buf;
-+
-+/* -------- Unit conversions -------- */
-+static inline u32 blk_pg(u16 block)
-+{
-+	return (u32)(block << (bmtd.blk_shift - bmtd.pg_shift));
-+}
-+
-+/* -------- Nand operations wrapper -------- */
-+static inline int
-+bbt_nand_read(u32 page, unsigned char *dat, int dat_len,
-+	      unsigned char *fdm, int fdm_len)
-+{
-+	struct mtd_oob_ops ops = {
-+		.mode = MTD_OPS_PLACE_OOB,
-+		.ooboffs = bmtd.oob_offset,
-+		.oobbuf = fdm,
-+		.ooblen = fdm_len,
-+		.datbuf = dat,
-+		.len = dat_len,
-+	};
-+
-+	return bmtd._read_oob(bmtd.mtd, page << bmtd.pg_shift, &ops);
-+}
-+
-+static inline int bbt_nand_erase(u16 block)
-+{
-+	struct nand_device *nand = mtd_to_nanddev(bmtd.mtd);
-+	loff_t addr = (loff_t)block << bmtd.blk_shift;
-+	struct nand_pos pos;
-+
-+	nanddev_offs_to_pos(nand, addr, &pos);
-+	return bmtd.nand_ops->erase(nand, &pos);
-+}
-+
-+/* -------- Bad Blocks Management -------- */
-+static int
-+read_bmt(u16 block, unsigned char *dat, unsigned char *fdm, int fdm_len)
-+{
-+	u32 len = bmtd.bmt_pgs << bmtd.pg_shift;
-+
-+	return bbt_nand_read(blk_pg(block), dat, len, fdm, fdm_len);
-+}
-+
-+static int write_bmt(u16 block, unsigned char *dat)
-+{
-+	struct mtd_oob_ops ops = {
-+		.mode = MTD_OPS_PLACE_OOB,
-+		.ooboffs = OOB_SIGNATURE_OFFSET + bmtd.oob_offset,
-+		.oobbuf = "bmt",
-+		.ooblen = 3,
-+		.datbuf = dat,
-+		.len = bmtd.bmt_pgs << bmtd.pg_shift,
-+	};
-+	loff_t addr = (loff_t)block << bmtd.blk_shift;
-+
-+	return bmtd._write_oob(bmtd.mtd, addr, &ops);
-+}
-+
-+static u16 find_valid_block(u16 block)
-+{
-+	u8 fdm[4];
-+	int ret;
-+	int loop = 0;
-+
-+retry:
-+	if (block >= bmtd.total_blks)
-+		return 0;
-+
-+	ret = bbt_nand_read(blk_pg(block), nand_data_buf, bmtd.pg_size,
-+			    fdm, sizeof(fdm));
-+	/* Read the 1st byte of FDM to judge whether it's a bad
-+	 * or not
-+	 */
-+	if (ret || fdm[0] != 0xff) {
-+		pr_info("nand: found bad block 0x%x\n", block);
-+		if (loop >= bmtd.bb_max) {
-+			pr_info("nand: FATAL ERR: too many bad blocks!!\n");
-+			return 0;
-+		}
-+
-+		loop++;
-+		block++;
-+		goto retry;
-+	}
-+
-+	return block;
-+}
-+
-+/* Find out all bad blocks, and fill in the mapping table */
-+static int scan_bad_blocks(struct bbbt *bbt)
-+{
-+	int i;
-+	u16 block = 0;
-+
-+	/* First time download, the block0 MUST NOT be a bad block,
-+	 * this is guaranteed by vendor
-+	 */
-+	bbt->bb_tbl[0] = 0;
-+
-+	/*
-+	 * Construct the mapping table of Normal data area(non-PMT/BMTPOOL)
-+	 * G - Good block; B - Bad block
-+	 *			---------------------------
-+	 * physical |G|G|B|G|B|B|G|G|G|G|B|G|B|
-+	 *			---------------------------
-+	 * What bb_tbl[i] looks like:
-+	 *   physical block(i):
-+	 *			 0 1 2 3 4 5 6 7 8 9 a b c
-+	 *   mapped block(bb_tbl[i]):
-+	 *			 0 1 3 6 7 8 9 b ......
-+	 * ATTENTION:
-+	 *		If new bad block ocurred(n), search bmt_tbl to find
-+	 *		a available block(x), and fill in the bb_tbl[n] = x;
-+	 */
-+	for (i = 1; i < bmtd.pool_lba; i++) {
-+		bbt->bb_tbl[i] = find_valid_block(bbt->bb_tbl[i - 1] + 1);
-+		BBT_LOG("bb_tbl[0x%x] = 0x%x", i, bbt->bb_tbl[i]);
-+		if (bbt->bb_tbl[i] == 0)
-+			return -1;
-+	}
-+
-+	/* Physical Block start Address of BMT pool */
-+	bmtd.pool_pba = bbt->bb_tbl[i - 1] + 1;
-+	if (bmtd.pool_pba >= bmtd.total_blks - 2) {
-+		pr_info("nand: FATAL ERR: Too many bad blocks!!\n");
-+		return -1;
-+	}
-+
-+	BBT_LOG("pool_pba=0x%x", bmtd.pool_pba);
-+	i = 0;
-+	block = bmtd.pool_pba;
-+	/*
-+	 * The bmt table is used for runtime bad block mapping
-+	 * G - Good block; B - Bad block
-+	 *			---------------------------
-+	 * physical |G|G|B|G|B|B|G|G|G|G|B|G|B|
-+	 *			---------------------------
-+	 *   block:	 0 1 2 3 4 5 6 7 8 9 a b c
-+	 * What bmt_tbl[i] looks like in initial state:
-+	 *   i:
-+	 *			 0 1 2 3 4 5 6 7
-+	 *   bmt_tbl[i].block:
-+	 *			 0 1 3 6 7 8 9 b
-+	 *   bmt_tbl[i].mapped:
-+	 *			 N N N N N N N B
-+	 *		N - Not mapped(Available)
-+	 *		M - Mapped
-+	 *		B - BMT
-+	 * ATTENTION:
-+	 *		BMT always in the last valid block in pool
-+	 */
-+	while ((block = find_valid_block(block)) != 0) {
-+		bbt->bmt_tbl[i].block = block;
-+		bbt->bmt_tbl[i].mapped = NO_MAPPED;
-+		BBT_LOG("bmt_tbl[%d].block = 0x%x", i, block);
-+		block++;
-+		i++;
-+	}
-+
-+	/* i - How many available blocks in pool, which is the length of bmt_tbl[]
-+	 * bmtd.bmt_blk_idx - bmt_tbl[bmtd.bmt_blk_idx].block => the BMT block
-+	 */
-+	bmtd.bmt_blk_idx = i - 1;
-+	bbt->bmt_tbl[bmtd.bmt_blk_idx].mapped = BMT_MAPPED;
-+
-+	if (i < 1) {
-+		pr_info("nand: FATAL ERR: no space to store BMT!!\n");
-+		return -1;
-+	}
-+
-+	pr_info("[BBT] %d available blocks in BMT pool\n", i);
-+
-+	return 0;
-+}
-+
-+static bool is_valid_bmt(unsigned char *buf, unsigned char *fdm)
-+{
-+	struct bbbt *bbt = (struct bbbt *)buf;
-+	u8 *sig = (u8*)bbt->signature + MAIN_SIGNATURE_OFFSET;
-+
-+
-+	if (memcmp(bbt->signature + MAIN_SIGNATURE_OFFSET, "BMT", 3) == 0 &&
-+		memcmp(fdm + OOB_SIGNATURE_OFFSET, "bmt", 3) == 0) {
-+		if (bbt->version == BBMT_VERSION)
-+			return true;
-+	}
-+	BBT_LOG("[BBT] BMT Version not match,upgrage preloader and uboot please! sig=%02x%02x%02x, fdm=%02x%02x%02x",
-+		sig[0], sig[1], sig[2],
-+		fdm[1], fdm[2], fdm[3]);
-+	return false;
-+}
-+
-+static u16 get_bmt_index(struct bbmt *bmt)
-+{
-+	int i = 0;
-+
-+	while (bmt[i].block != BMT_TBL_DEF_VAL) {
-+		if (bmt[i].mapped == BMT_MAPPED)
-+			return i;
-+		i++;
-+	}
-+	return 0;
-+}
-+
-+static struct bbbt *scan_bmt(u16 block)
-+{
-+	u8 fdm[4];
-+
-+	if (block < bmtd.pool_lba)
-+		return NULL;
-+
-+	if (read_bmt(block, nand_bbt_buf, fdm, sizeof(fdm)))
-+		return scan_bmt(block - 1);
-+
-+	if (is_valid_bmt(nand_bbt_buf, fdm)) {
-+		bmtd.bmt_blk_idx = get_bmt_index(((struct bbbt *)nand_bbt_buf)->bmt_tbl);
-+		if (bmtd.bmt_blk_idx == 0) {
-+			pr_info("[BBT] FATAL ERR: bmt block index is wrong!\n");
-+			return NULL;
-+		}
-+		pr_info("[BBT] BMT.v2 is found at 0x%x\n", block);
-+		return (struct bbbt *)nand_bbt_buf;
-+	} else
-+		return scan_bmt(block - 1);
-+}
-+
-+/* Write the Burner Bad Block Table to Nand Flash
-+ * n - write BMT to bmt_tbl[n]
-+ */
-+static u16 upload_bmt(struct bbbt *bbt, int n)
-+{
-+	u16 block;
-+
-+retry:
-+	if (n < 0 || bbt->bmt_tbl[n].mapped == NORMAL_MAPPED) {
-+		pr_info("nand: FATAL ERR: no space to store BMT!\n");
-+		return (u16)-1;
-+	}
-+
-+	block = bbt->bmt_tbl[n].block;
-+	BBT_LOG("n = 0x%x, block = 0x%x", n, block);
-+	if (bbt_nand_erase(block)) {
-+		bbt->bmt_tbl[n].block = 0;
-+		/* erase failed, try the previous block: bmt_tbl[n - 1].block */
-+		n--;
-+		goto retry;
-+	}
-+
-+	/* The signature offset is fixed set to 0,
-+	 * oob signature offset is fixed set to 1
-+	 */
-+	memcpy(bbt->signature + MAIN_SIGNATURE_OFFSET, "BMT", 3);
-+	bbt->version = BBMT_VERSION;
-+
-+	if (write_bmt(block, (unsigned char *)bbt)) {
-+		bbt->bmt_tbl[n].block = 0;
-+
-+		/* write failed, try the previous block in bmt_tbl[n - 1] */
-+		n--;
-+		goto retry;
-+	}
-+
-+	/* Return the current index(n) of BMT pool (bmt_tbl[n]) */
-+	return n;
-+}
-+
-+static u16 find_valid_block_in_pool(struct bbbt *bbt)
-+{
-+	int i;
-+
-+	if (bmtd.bmt_blk_idx == 0)
-+		goto error;
-+
-+	for (i = 0; i < bmtd.bmt_blk_idx; i++) {
-+		if (bbt->bmt_tbl[i].block != 0 && bbt->bmt_tbl[i].mapped == NO_MAPPED) {
-+			bbt->bmt_tbl[i].mapped = NORMAL_MAPPED;
-+			return bbt->bmt_tbl[i].block;
-+		}
-+	}
-+
-+error:
-+	pr_info("nand: FATAL ERR: BMT pool is run out!\n");
-+	return 0;
-+}
-+
-+/* We met a bad block, mark it as bad and map it to a valid block in pool,
-+ * if it's a write failure, we need to write the data to mapped block
-+ */
-+static bool update_bmt(u16 block)
-+{
-+	u16 mapped_blk;
-+	struct bbbt *bbt;
-+
-+	bbt = bmtd.bbt;
-+	mapped_blk = find_valid_block_in_pool(bbt);
-+	if (mapped_blk == 0)
-+		return false;
-+
-+	/* Map new bad block to available block in pool */
-+	bbt->bb_tbl[block] = mapped_blk;
-+	bmtd.bmt_blk_idx = upload_bmt(bbt, bmtd.bmt_blk_idx);
-+
-+	return true;
-+}
-+
-+u16 get_mapping_block_index(int block)
-+{
-+	int mapping_block;
-+
-+	if (block < bmtd.pool_lba)
-+		mapping_block = bmtd.bbt->bb_tbl[block];
-+	else
-+		mapping_block = block;
-+	BBT_LOG("0x%x mapped to 0x%x", block, mapping_block);
-+
-+	return mapping_block;
-+}
-+
-+static int
-+mtk_bmt_read(struct mtd_info *mtd, loff_t from,
-+	     struct mtd_oob_ops *ops)
-+{
-+	struct mtd_oob_ops cur_ops = *ops;
-+	int retry_count = 0;
-+	loff_t cur_from;
-+	int ret;
-+
-+	ops->retlen = 0;
-+	ops->oobretlen = 0;
-+
-+	while (ops->retlen < ops->len || ops->oobretlen < ops->ooblen) {
-+		u32 offset = from & (bmtd.blk_size - 1);
-+		u32 block = from >> bmtd.blk_shift;
-+		u32 cur_block;
-+
-+		cur_block = get_mapping_block_index(block);
-+		cur_from = ((loff_t)cur_block << bmtd.blk_shift) + offset;
-+
-+		cur_ops.oobretlen = 0;
-+		cur_ops.retlen = 0;
-+		cur_ops.len = min_t(u32, mtd->erasesize - offset,
-+					 ops->len - ops->retlen);
-+		ret = bmtd._read_oob(mtd, cur_from, &cur_ops);
-+		if (ret < 0) {
-+			update_bmt(block);
-+			if (retry_count++ < 10)
-+				continue;
-+
-+			return ret;
-+		}
-+
-+		ops->retlen += cur_ops.retlen;
-+		ops->oobretlen += cur_ops.oobretlen;
-+
-+		cur_ops.datbuf += cur_ops.retlen;
-+		cur_ops.oobbuf += cur_ops.oobretlen;
-+		cur_ops.ooblen -= cur_ops.oobretlen;
-+
-+		if (!cur_ops.len)
-+			cur_ops.len = mtd->erasesize - offset;
-+
-+		from += cur_ops.len;
-+		retry_count = 0;
-+	}
-+
-+	return 0;
-+}
-+
-+static int
-+mtk_bmt_write(struct mtd_info *mtd, loff_t to,
-+	      struct mtd_oob_ops *ops)
-+{
-+	struct mtd_oob_ops cur_ops = *ops;
-+	int retry_count = 0;
-+	loff_t cur_to;
-+	int ret;
-+
-+	ops->retlen = 0;
-+	ops->oobretlen = 0;
-+
-+	while (ops->retlen < ops->len || ops->oobretlen < ops->ooblen) {
-+		u32 offset = to & (bmtd.blk_size - 1);
-+		u32 block = to >> bmtd.blk_shift;
-+		u32 cur_block;
-+
-+		cur_block = get_mapping_block_index(block);
-+		cur_to = ((loff_t)cur_block << bmtd.blk_shift) + offset;
-+
-+		cur_ops.oobretlen = 0;
-+		cur_ops.retlen = 0;
-+		cur_ops.len = min_t(u32, bmtd.blk_size - offset,
-+					 ops->len - ops->retlen);
-+		ret = bmtd._write_oob(mtd, cur_to, &cur_ops);
-+		if (ret < 0) {
-+			update_bmt(block);
-+			if (retry_count++ < 10)
-+				continue;
-+
-+			return ret;
-+		}
-+
-+		ops->retlen += cur_ops.retlen;
-+		ops->oobretlen += cur_ops.oobretlen;
-+
-+		cur_ops.datbuf += cur_ops.retlen;
-+		cur_ops.oobbuf += cur_ops.oobretlen;
-+		cur_ops.ooblen -= cur_ops.oobretlen;
-+
-+		if (!cur_ops.len)
-+			cur_ops.len = mtd->erasesize - offset;
-+
-+		to += cur_ops.len;
-+		retry_count = 0;
-+	}
-+
-+	return 0;
-+}
-+
-+
-+
-+static int
-+mtk_bmt_erase(struct nand_device *nand, const struct nand_pos *pos)
-+{
-+	struct nand_pos new_pos = *pos;
-+	int retry_count = 0;
-+	int ret;
-+
-+retry:
-+	new_pos.eraseblock = get_mapping_block_index(pos->eraseblock);
-+
-+	ret = bmtd.nand_ops->erase(nand, &new_pos);
-+	if (ret) {
-+		update_bmt(pos->eraseblock);
-+		if (retry_count++ < 10)
-+			goto retry;
-+	}
-+
-+	return ret;
-+}
-+
-+static bool
-+mtk_bmt_isbad(struct nand_device *nand, const struct nand_pos *pos)
-+{
-+	struct nand_pos new_pos = *pos;
-+	int retry_count = 0;
-+	bool ret;
-+
-+retry:
-+	new_pos.eraseblock = get_mapping_block_index(pos->eraseblock);
-+
-+	ret = bmtd.nand_ops->isbad(nand, &new_pos);
-+	if (ret) {
-+		update_bmt(pos->eraseblock);
-+		if (retry_count++ < 10)
-+			goto retry;
-+	}
-+
-+	return ret;
-+}
-+
-+static int
-+mtk_bmt_markbad(struct nand_device *nand, const struct nand_pos *pos)
-+{
-+	struct nand_pos new_pos = *pos;
-+
-+	new_pos.eraseblock = get_mapping_block_index(new_pos.eraseblock);
-+	update_bmt(pos->eraseblock);
-+
-+	return bmtd.nand_ops->markbad(nand, &new_pos);
-+}
-+
-+static void
-+mtk_bmt_replace_ops(struct mtd_info *mtd)
-+{
-+	static const struct nand_ops mtk_bmt_nand_ops = {
-+		.erase = mtk_bmt_erase,
-+		.isbad = mtk_bmt_isbad,
-+		.markbad = mtk_bmt_markbad,
-+	};
-+	struct nand_device *nand = mtd_to_nanddev(mtd);
-+
-+	bmtd.nand_ops = nand->ops;
-+	bmtd._read_oob = mtd->_read_oob;
-+	bmtd._write_oob = mtd->_write_oob;
-+
-+	mtd->_read_oob = mtk_bmt_read;
-+	mtd->_write_oob = mtk_bmt_write;
-+	nand->ops = &mtk_bmt_nand_ops;
-+}
-+
-+static int mtk_bmt_debug_mark_good(void *data, u64 val)
-+{
-+	u32 block = val >> bmtd.blk_shift;
-+
-+	bmtd.bbt->bb_tbl[block] = block;
-+	bmtd.bmt_blk_idx = upload_bmt(bmtd.bbt, bmtd.bmt_blk_idx);
-+
-+	return 0;
-+}
-+
-+static int mtk_bmt_debug_mark_bad(void *data, u64 val)
-+{
-+	u32 block = val >> bmtd.blk_shift;
-+
-+	update_bmt(block);
-+
-+	return 0;
-+}
-+
-+DEFINE_DEBUGFS_ATTRIBUTE(fops_mark_good, NULL, mtk_bmt_debug_mark_good, "%llu\n");
-+DEFINE_DEBUGFS_ATTRIBUTE(fops_mark_bad, NULL, mtk_bmt_debug_mark_bad, "%llu\n");
-+
-+static void
-+mtk_bmt_add_debugfs(void)
-+{
-+	struct dentry *dir;
-+
-+	dir = bmtd.debugfs_dir = debugfs_create_dir("mtk-bmt", NULL);
-+	if (!dir)
-+		return;
-+
-+	debugfs_create_file_unsafe("mark_good", S_IWUSR, dir, NULL, &fops_mark_good);
-+	debugfs_create_file_unsafe("mark_bad", S_IWUSR, dir, NULL, &fops_mark_bad);
-+}
-+
-+void mtk_bmt_detach(struct mtd_info *mtd)
-+{
-+	struct nand_device *nand = mtd_to_nanddev(mtd);
-+
-+	if (bmtd.mtd != mtd)
-+		return;
-+
-+	if (bmtd.debugfs_dir)
-+		debugfs_remove_recursive(bmtd.debugfs_dir);
-+	bmtd.debugfs_dir = NULL;
-+
-+	kfree(nand_bbt_buf);
-+	kfree(nand_data_buf);
-+
-+	mtd->_read_oob = bmtd._read_oob;
-+	mtd->_write_oob = bmtd._write_oob;
-+	mtd->size = bmtd.total_blks << bmtd.blk_shift;
-+	nand->ops = bmtd.nand_ops;
-+
-+	memset(&bmtd, 0, sizeof(bmtd));
-+}
-+
-+/* total_blocks - The total count of blocks that the Nand Chip has */
-+int mtk_bmt_attach(struct mtd_info *mtd)
-+{
-+	struct device_node *np;
-+	struct bbbt *bbt;
-+	u32 bufsz;
-+	u32 block;
-+	u16 total_blocks, pmt_block;
-+	int ret = 0;
-+	u32 bmt_pool_size;
-+
-+	if (bmtd.mtd)
-+		return -ENOSPC;
-+
-+	np = mtd_get_of_node(mtd);
-+	if (!np)
-+		return 0;
-+
-+	if (!of_property_read_bool(np, "mediatek,bmt-v2"))
-+		return 0;
-+
-+	if (of_property_read_u32(np, "mediatek,bmt-pool-size",
-+				 &bmt_pool_size) != 0)
-+		bmt_pool_size = 80;
-+
-+	if (of_property_read_u8(np, "mediatek,bmt-oob-offset",
-+				 &bmtd.oob_offset) != 0)
-+		bmtd.oob_offset = 8;
-+
-+	bmtd.mtd = mtd;
-+	mtk_bmt_replace_ops(mtd);
-+
-+	bmtd.blk_size = mtd->erasesize;
-+	bmtd.blk_shift = ffs(bmtd.blk_size) - 1;
-+	bmtd.pg_size = mtd->writesize;
-+	bmtd.pg_shift = ffs(bmtd.pg_size) - 1;
-+	total_blocks = mtd->size >> bmtd.blk_shift;
-+	pmt_block = total_blocks - bmt_pool_size - 2;
-+
-+	mtd->size = pmt_block << bmtd.blk_shift;
-+
-+	/*
-+	 *  ---------------------------------------
-+	 * | PMT(2blks) | BMT POOL(totalblks * 2%) |
-+	 *  ---------------------------------------
-+	 * ^            ^
-+	 * |            |
-+	 * pmt_block	pmt_block + 2blocks(pool_lba)
-+	 *
-+	 * ATTETION!!!!!!
-+	 *     The blocks ahead of the boundary block are stored in bb_tbl
-+	 *     and blocks behind are stored in bmt_tbl
-+	 */
-+
-+	bmtd.pool_lba = (u16)(pmt_block + 2);
-+	bmtd.total_blks = total_blocks;
-+	bmtd.bb_max = bmtd.total_blks * BBPOOL_RATIO / 100;
-+
-+	/* 3 buffers we need */
-+	bufsz = round_up(sizeof(struct bbbt), bmtd.pg_size);
-+	bmtd.bmt_pgs = bufsz >> bmtd.pg_shift;
-+
-+	nand_bbt_buf = kzalloc(bufsz, GFP_KERNEL);
-+	nand_data_buf = kzalloc(bmtd.pg_size, GFP_KERNEL);
-+
-+	if (!nand_bbt_buf || !nand_data_buf) {
-+		pr_info("nand: FATAL ERR: allocate buffer failed!\n");
-+		ret = -1;
-+		goto error;
-+	}
-+
-+	memset(nand_bbt_buf, 0xff, bufsz);
-+	memset(nand_data_buf, 0xff, bmtd.pg_size);
-+
-+	BBT_LOG("bbtbuf=0x%p(0x%x) dat=0x%p(0x%x)",
-+			nand_bbt_buf, bufsz, nand_data_buf, bmtd.pg_size);
-+	BBT_LOG("pool_lba=0x%x total_blks=0x%x bb_max=0x%x",
-+			bmtd.pool_lba, bmtd.total_blks, bmtd.bb_max);
-+
-+	/* Scanning start from the first page of the last block
-+	 * of whole flash
-+	 */
-+	bbt = scan_bmt(bmtd.total_blks - 1);
-+	if (!bbt) {
-+		/* BMT not found */
-+		if (bmtd.total_blks > BB_TABLE_MAX + BMT_TABLE_MAX) {
-+			pr_info("nand: FATAL: Too many blocks, can not support!\n");
-+			ret = -1;
-+			goto error;
-+		}
-+
-+		bbt = (struct bbbt *)nand_bbt_buf;
-+		memset(bbt->bmt_tbl, BMT_TBL_DEF_VAL, sizeof(bbt->bmt_tbl));
-+
-+		if (scan_bad_blocks(bbt)) {
-+			ret = -1;
-+			goto error;
-+		}
-+
-+		/* BMT always in the last valid block in pool */
-+		bmtd.bmt_blk_idx = upload_bmt(bbt, bmtd.bmt_blk_idx);
-+		block = bbt->bmt_tbl[bmtd.bmt_blk_idx].block;
-+		pr_notice("[BBT] BMT.v2 is written into PBA:0x%x\n", block);
-+
-+		if (bmtd.bmt_blk_idx == 0)
-+			pr_info("nand: Warning: no available block in BMT pool!\n");
-+		else if (bmtd.bmt_blk_idx == (u16)-1) {
-+			ret = -1;
-+			goto error;
-+		}
-+	}
-+	mtk_bmt_add_debugfs();
-+
-+	bmtd.bbt = bbt;
-+	return 0;
-+
-+error:
-+	mtk_bmt_detach(mtd);
-+	return ret;
-+}
-+
-+
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Xiangsheng Hou <xiangsheng.hou@mediatek.com>, Felix Fietkau <nbd@nbd.name>");
-+MODULE_DESCRIPTION("Bad Block mapping management v2 for MediaTek NAND Flash Driver");
-+
---- a/drivers/mtd/nand/spi/core.c
-+++ b/drivers/mtd/nand/spi/core.c
-@@ -18,6 +18,7 @@
- #include <linux/slab.h>
- #include <linux/spi/spi.h>
- #include <linux/spi/spi-mem.h>
-+#include <linux/mtd/mtk_bmt.h>
- 
- static int spinand_read_reg_op(struct spinand_device *spinand, u8 reg, u8 *val)
- {
-@@ -1100,6 +1101,8 @@ static int spinand_probe(struct spi_mem
- 	if (ret)
- 		return ret;
- 
-+	mtk_bmt_attach(mtd);
-+
- 	ret = mtd_device_register(mtd, NULL, 0);
- 	if (ret)
- 		goto err_spinand_cleanup;
-@@ -1125,6 +1128,7 @@ static int spinand_remove(struct spi_mem
- 	if (ret)
- 		return ret;
- 
-+	mtk_bmt_detach(mtd);
- 	spinand_cleanup(spinand);
- 
- 	return 0;
---- /dev/null
-+++ b/include/linux/mtd/mtk_bmt.h
-@@ -0,0 +1,18 @@
-+#ifndef __MTK_BMT_H
-+#define __MTK_BMT_H
-+
-+#ifdef CONFIG_MTD_NAND_MTK_BMT
-+int mtk_bmt_attach(struct mtd_info *mtd);
-+void mtk_bmt_detach(struct mtd_info *mtd);
-+#else
-+static inline int mtk_bmt_attach(struct mtd_info *mtd)
-+{
-+	return 0;
-+}
-+
-+static inline void mtk_bmt_detach(struct mtd_info *mtd)
-+{
-+}
-+#endif
-+
-+#endif
diff --git a/target/linux/mediatek/patches-5.4/0350-mtd-parsers-trx-Allow-to-specify-trx-magic-in-DT.patch b/target/linux/mediatek/patches-5.4/0350-mtd-parsers-trx-Allow-to-specify-trx-magic-in-DT.patch
deleted file mode 100644
index 0446ce9386..0000000000
--- a/target/linux/mediatek/patches-5.4/0350-mtd-parsers-trx-Allow-to-specify-trx-magic-in-DT.patch
+++ /dev/null
@@ -1,75 +0,0 @@
-From 0600e3d81628002a5cd80cf83ee454851b0063c0 Mon Sep 17 00:00:00 2001
-From: Hauke Mehrtens <hauke@hauke-m.de>
-Date: Sun, 7 Mar 2021 18:19:26 +0100
-Subject: mtd: parsers: trx: Allow to specify brcm,trx-magic in DT
-
-Buffalo uses a different TRX magic for every device, to be able to use
-this trx parser, make it possible to specify the TRX magic in device
-tree. If no TRX magic is specified in device tree, the standard value
-will be used. This value should only be specified if a vendor chooses to
-use a non standard TRX magic.
-
-Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
----
- .../bindings/mtd/partitions/brcm,trx.txt      |  5 +++++
- drivers/mtd/parsers/parser_trx.c              | 21 ++++++++++++++++++-
- 2 files changed, 25 insertions(+), 1 deletion(-)
-
---- a/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt
-+++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt
-@@ -28,6 +28,11 @@ detected by a software parsing TRX heade
- Required properties:
- - compatible : (required) must be "brcm,trx"
- 
-+Optional properties:
-+
-+- brcm,trx-magic: TRX magic, if it is different from the default magic
-+	     0x30524448 as a u32.
-+
- Example:
- 
- flash@0 {
---- a/drivers/mtd/parsers/parser_trx.c
-+++ b/drivers/mtd/parsers/parser_trx.c
-@@ -74,6 +74,24 @@ out_default:
- 	return "rootfs";
- }
- 
-+static uint32_t parser_trx_get_magic(struct mtd_info *mtd)
-+{
-+	uint32_t trx_magic = TRX_MAGIC;
-+	struct device_node *np;
-+	int err;
-+
-+	np = mtd_get_of_node(mtd);
-+	if (!np)
-+		return trx_magic;
-+
-+	/* Get different magic from device tree if specified */
-+	err = of_property_read_u32(np, "brcm,trx-magic", &trx_magic);
-+	if (err != 0 && err != -EINVAL)
-+		pr_err("failed to parse \"brcm,trx-magic\" DT attribute, use default: %d\n", err);
-+
-+	return trx_magic;
-+}
-+
- static int parser_trx_parse(struct mtd_info *mtd,
- 			    const struct mtd_partition **pparts,
- 			    struct mtd_part_parser_data *data)
-@@ -83,6 +101,7 @@ static int parser_trx_parse(struct mtd_i
- 	struct trx_header trx;
- 	size_t bytes_read;
- 	uint8_t curr_part = 0, i = 0;
-+	uint32_t trx_magic = parser_trx_get_magic(mtd);
- 	int err;
- 
- 	parts = kcalloc(TRX_PARSER_MAX_PARTS, sizeof(struct mtd_partition),
-@@ -97,7 +116,7 @@ static int parser_trx_parse(struct mtd_i
- 		return err;
- 	}
- 
--	if (trx.magic != TRX_MAGIC) {
-+	if (trx.magic != trx_magic) {
- 		kfree(parts);
- 		return -ENOENT;
- 	}
diff --git a/target/linux/mediatek/patches-5.4/0351-mtd-parsers-Remove-dependency-to-BRCM-architectures.patch b/target/linux/mediatek/patches-5.4/0351-mtd-parsers-Remove-dependency-to-BRCM-architectures.patch
deleted file mode 100644
index fa94c22304..0000000000
--- a/target/linux/mediatek/patches-5.4/0351-mtd-parsers-Remove-dependency-to-BRCM-architectures.patch
+++ /dev/null
@@ -1,23 +0,0 @@
-From 63f0cf88ab5461acb0911252f12bb94ee3bf05a2 Mon Sep 17 00:00:00 2001
-From: Hauke Mehrtens <hauke@hauke-m.de>
-Date: Sun, 7 Mar 2021 18:23:29 +0100
-Subject: mtd: parsers: Remove dependency to BRCM architectures
-
-Buffalo uses the TRX partition format also on Mediatek SoCs.
-
-Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
----
- drivers/mtd/parsers/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/mtd/parsers/Kconfig
-+++ b/drivers/mtd/parsers/Kconfig
-@@ -131,7 +131,7 @@ config MTD_AFS_PARTS
- 
- config MTD_PARSER_TRX
- 	tristate "Parser for TRX format partitions"
--	depends on MTD && (BCM47XX || ARCH_BCM_5301X || COMPILE_TEST)
-+	depends on MTD
- 	help
- 	  TRX is a firmware format used by Broadcom on their devices. It
- 	  may contain up to 3/4 partitions (depending on the version).
diff --git a/target/linux/mediatek/patches-5.4/0500-v5.6-crypto-backport-inside-secure.patch b/target/linux/mediatek/patches-5.4/0500-v5.6-crypto-backport-inside-secure.patch
deleted file mode 100644
index 2fae90ef9e..0000000000
--- a/target/linux/mediatek/patches-5.4/0500-v5.6-crypto-backport-inside-secure.patch
+++ /dev/null
@@ -1,5464 +0,0 @@
---- a/drivers/crypto/inside-secure/safexcel.c
-+++ b/drivers/crypto/inside-secure/safexcel.c
-@@ -75,9 +75,9 @@ static void eip197_trc_cache_banksel(str
- }
- 
- static u32 eip197_trc_cache_probe(struct safexcel_crypto_priv *priv,
--				  int maxbanks, u32 probemask)
-+				  int maxbanks, u32 probemask, u32 stride)
- {
--	u32 val, addrhi, addrlo, addrmid;
-+	u32 val, addrhi, addrlo, addrmid, addralias, delta, marker;
- 	int actbank;
- 
- 	/*
-@@ -87,32 +87,37 @@ static u32 eip197_trc_cache_probe(struct
- 	addrhi = 1 << (16 + maxbanks);
- 	addrlo = 0;
- 	actbank = min(maxbanks - 1, 0);
--	while ((addrhi - addrlo) > 32) {
-+	while ((addrhi - addrlo) > stride) {
- 		/* write marker to lowest address in top half */
- 		addrmid = (addrhi + addrlo) >> 1;
-+		marker = (addrmid ^ 0xabadbabe) & probemask; /* Unique */
- 		eip197_trc_cache_banksel(priv, addrmid, &actbank);
--		writel((addrmid | (addrlo << 16)) & probemask,
-+		writel(marker,
- 			priv->base + EIP197_CLASSIFICATION_RAMS +
- 			(addrmid & 0xffff));
- 
--		/* write marker to lowest address in bottom half */
--		eip197_trc_cache_banksel(priv, addrlo, &actbank);
--		writel((addrlo | (addrhi << 16)) & probemask,
--			priv->base + EIP197_CLASSIFICATION_RAMS +
--			(addrlo & 0xffff));
-+		/* write invalid markers to possible aliases */
-+		delta = 1 << __fls(addrmid);
-+		while (delta >= stride) {
-+			addralias = addrmid - delta;
-+			eip197_trc_cache_banksel(priv, addralias, &actbank);
-+			writel(~marker,
-+			       priv->base + EIP197_CLASSIFICATION_RAMS +
-+			       (addralias & 0xffff));
-+			delta >>= 1;
-+		}
- 
- 		/* read back marker from top half */
- 		eip197_trc_cache_banksel(priv, addrmid, &actbank);
- 		val = readl(priv->base + EIP197_CLASSIFICATION_RAMS +
- 			    (addrmid & 0xffff));
- 
--		if (val == ((addrmid | (addrlo << 16)) & probemask)) {
-+		if ((val & probemask) == marker)
- 			/* read back correct, continue with top half */
- 			addrlo = addrmid;
--		} else {
-+		else
- 			/* not read back correct, continue with bottom half */
- 			addrhi = addrmid;
--		}
- 	}
- 	return addrhi;
- }
-@@ -150,7 +155,7 @@ static void eip197_trc_cache_clear(struc
- 		       htable_offset + i * sizeof(u32));
- }
- 
--static void eip197_trc_cache_init(struct safexcel_crypto_priv *priv)
-+static int eip197_trc_cache_init(struct safexcel_crypto_priv *priv)
- {
- 	u32 val, dsize, asize;
- 	int cs_rc_max, cs_ht_wc, cs_trc_rec_wc, cs_trc_lg_rec_wc;
-@@ -183,7 +188,7 @@ static void eip197_trc_cache_init(struct
- 	writel(val, priv->base + EIP197_TRC_PARAMS);
- 
- 	/* Probed data RAM size in bytes */
--	dsize = eip197_trc_cache_probe(priv, maxbanks, 0xffffffff);
-+	dsize = eip197_trc_cache_probe(priv, maxbanks, 0xffffffff, 32);
- 
- 	/*
- 	 * Now probe the administration RAM size pretty much the same way
-@@ -196,11 +201,18 @@ static void eip197_trc_cache_init(struct
- 	writel(val, priv->base + EIP197_TRC_PARAMS);
- 
- 	/* Probed admin RAM size in admin words */
--	asize = eip197_trc_cache_probe(priv, 0, 0xbfffffff) >> 4;
-+	asize = eip197_trc_cache_probe(priv, 0, 0x3fffffff, 16) >> 4;
- 
- 	/* Clear any ECC errors detected while probing! */
- 	writel(0, priv->base + EIP197_TRC_ECCCTRL);
- 
-+	/* Sanity check probing results */
-+	if (dsize < EIP197_MIN_DSIZE || asize < EIP197_MIN_ASIZE) {
-+		dev_err(priv->dev, "Record cache probing failed (%d,%d).",
-+			dsize, asize);
-+		return -ENODEV;
-+	}
-+
- 	/*
- 	 * Determine optimal configuration from RAM sizes
- 	 * Note that we assume that the physical RAM configuration is sane
-@@ -251,6 +263,7 @@ static void eip197_trc_cache_init(struct
- 
- 	dev_info(priv->dev, "TRC init: %dd,%da (%dr,%dh)\n",
- 		 dsize, asize, cs_rc_max, cs_ht_wc + cs_ht_wc);
-+	return 0;
- }
- 
- static void eip197_init_firmware(struct safexcel_crypto_priv *priv)
-@@ -298,13 +311,14 @@ static void eip197_init_firmware(struct
- static int eip197_write_firmware(struct safexcel_crypto_priv *priv,
- 				  const struct firmware *fw)
- {
--	const u32 *data = (const u32 *)fw->data;
-+	const __be32 *data = (const __be32 *)fw->data;
- 	int i;
- 
- 	/* Write the firmware */
- 	for (i = 0; i < fw->size / sizeof(u32); i++)
- 		writel(be32_to_cpu(data[i]),
--		       priv->base + EIP197_CLASSIFICATION_RAMS + i * sizeof(u32));
-+		       priv->base + EIP197_CLASSIFICATION_RAMS +
-+		       i * sizeof(__be32));
- 
- 	/* Exclude final 2 NOPs from size */
- 	return i - EIP197_FW_TERMINAL_NOPS;
-@@ -471,6 +485,14 @@ static int safexcel_hw_setup_cdesc_rings
- 		cd_fetch_cnt = ((1 << priv->hwconfig.hwcfsize) /
- 				cd_size_rnd) - 1;
- 	}
-+	/*
-+	 * Since we're using command desc's way larger than formally specified,
-+	 * we need to check whether we can fit even 1 for low-end EIP196's!
-+	 */
-+	if (!cd_fetch_cnt) {
-+		dev_err(priv->dev, "Unable to fit even 1 command desc!\n");
-+		return -ENODEV;
-+	}
- 
- 	for (i = 0; i < priv->config.rings; i++) {
- 		/* ring base address */
-@@ -479,12 +501,12 @@ static int safexcel_hw_setup_cdesc_rings
- 		writel(upper_32_bits(priv->ring[i].cdr.base_dma),
- 		       EIP197_HIA_CDR(priv, i) + EIP197_HIA_xDR_RING_BASE_ADDR_HI);
- 
--		writel(EIP197_xDR_DESC_MODE_64BIT | (priv->config.cd_offset << 16) |
--		       priv->config.cd_size,
-+		writel(EIP197_xDR_DESC_MODE_64BIT | EIP197_CDR_DESC_MODE_ADCP |
-+		       (priv->config.cd_offset << 14) | priv->config.cd_size,
- 		       EIP197_HIA_CDR(priv, i) + EIP197_HIA_xDR_DESC_SIZE);
- 		writel(((cd_fetch_cnt *
- 			 (cd_size_rnd << priv->hwconfig.hwdataw)) << 16) |
--		       (cd_fetch_cnt * priv->config.cd_offset),
-+		       (cd_fetch_cnt * (priv->config.cd_offset / sizeof(u32))),
- 		       EIP197_HIA_CDR(priv, i) + EIP197_HIA_xDR_CFG);
- 
- 		/* Configure DMA tx control */
-@@ -527,13 +549,13 @@ static int safexcel_hw_setup_rdesc_rings
- 		writel(upper_32_bits(priv->ring[i].rdr.base_dma),
- 		       EIP197_HIA_RDR(priv, i) + EIP197_HIA_xDR_RING_BASE_ADDR_HI);
- 
--		writel(EIP197_xDR_DESC_MODE_64BIT | (priv->config.rd_offset << 16) |
-+		writel(EIP197_xDR_DESC_MODE_64BIT | (priv->config.rd_offset << 14) |
- 		       priv->config.rd_size,
- 		       EIP197_HIA_RDR(priv, i) + EIP197_HIA_xDR_DESC_SIZE);
- 
- 		writel(((rd_fetch_cnt *
- 			 (rd_size_rnd << priv->hwconfig.hwdataw)) << 16) |
--		       (rd_fetch_cnt * priv->config.rd_offset),
-+		       (rd_fetch_cnt * (priv->config.rd_offset / sizeof(u32))),
- 		       EIP197_HIA_RDR(priv, i) + EIP197_HIA_xDR_CFG);
- 
- 		/* Configure DMA tx control */
-@@ -559,7 +581,7 @@ static int safexcel_hw_setup_rdesc_rings
- static int safexcel_hw_init(struct safexcel_crypto_priv *priv)
- {
- 	u32 val;
--	int i, ret, pe;
-+	int i, ret, pe, opbuflo, opbufhi;
- 
- 	dev_dbg(priv->dev, "HW init: using %d pipe(s) and %d ring(s)\n",
- 		priv->config.pes, priv->config.rings);
-@@ -595,8 +617,8 @@ static int safexcel_hw_init(struct safex
- 		writel(EIP197_DxE_THR_CTRL_RESET_PE,
- 		       EIP197_HIA_DFE_THR(priv) + EIP197_HIA_DFE_THR_CTRL(pe));
- 
--		if (priv->flags & SAFEXCEL_HW_EIP197)
--			/* Reset HIA input interface arbiter (EIP197 only) */
-+		if (priv->flags & EIP197_PE_ARB)
-+			/* Reset HIA input interface arbiter (if present) */
- 			writel(EIP197_HIA_RA_PE_CTRL_RESET,
- 			       EIP197_HIA_AIC(priv) + EIP197_HIA_RA_PE_CTRL(pe));
- 
-@@ -639,9 +661,16 @@ static int safexcel_hw_init(struct safex
- 			;
- 
- 		/* DMA transfer size to use */
-+		if (priv->hwconfig.hwnumpes > 4) {
-+			opbuflo = 9;
-+			opbufhi = 10;
-+		} else {
-+			opbuflo = 7;
-+			opbufhi = 8;
-+		}
- 		val = EIP197_HIA_DSE_CFG_DIS_DEBUG;
--		val |= EIP197_HIA_DxE_CFG_MIN_DATA_SIZE(7) |
--		       EIP197_HIA_DxE_CFG_MAX_DATA_SIZE(8);
-+		val |= EIP197_HIA_DxE_CFG_MIN_DATA_SIZE(opbuflo) |
-+		       EIP197_HIA_DxE_CFG_MAX_DATA_SIZE(opbufhi);
- 		val |= EIP197_HIA_DxE_CFG_DATA_CACHE_CTRL(WR_CACHE_3BITS);
- 		val |= EIP197_HIA_DSE_CFG_ALWAYS_BUFFERABLE;
- 		/* FIXME: instability issues can occur for EIP97 but disabling
-@@ -655,8 +684,8 @@ static int safexcel_hw_init(struct safex
- 		writel(0, EIP197_HIA_DSE_THR(priv) + EIP197_HIA_DSE_THR_CTRL(pe));
- 
- 		/* Configure the procesing engine thresholds */
--		writel(EIP197_PE_OUT_DBUF_THRES_MIN(7) |
--		       EIP197_PE_OUT_DBUF_THRES_MAX(8),
-+		writel(EIP197_PE_OUT_DBUF_THRES_MIN(opbuflo) |
-+		       EIP197_PE_OUT_DBUF_THRES_MAX(opbufhi),
- 		       EIP197_PE(priv) + EIP197_PE_OUT_DBUF_THRES(pe));
- 
- 		/* Processing Engine configuration */
-@@ -696,7 +725,7 @@ static int safexcel_hw_init(struct safex
- 		writel(0,
- 		       EIP197_HIA_CDR(priv, i) + EIP197_HIA_xDR_PROC_PNTR);
- 
--		writel((EIP197_DEFAULT_RING_SIZE * priv->config.cd_offset) << 2,
-+		writel((EIP197_DEFAULT_RING_SIZE * priv->config.cd_offset),
- 		       EIP197_HIA_CDR(priv, i) + EIP197_HIA_xDR_RING_SIZE);
- 	}
- 
-@@ -719,7 +748,7 @@ static int safexcel_hw_init(struct safex
- 		       EIP197_HIA_RDR(priv, i) + EIP197_HIA_xDR_PROC_PNTR);
- 
- 		/* Ring size */
--		writel((EIP197_DEFAULT_RING_SIZE * priv->config.rd_offset) << 2,
-+		writel((EIP197_DEFAULT_RING_SIZE * priv->config.rd_offset),
- 		       EIP197_HIA_RDR(priv, i) + EIP197_HIA_xDR_RING_SIZE);
- 	}
- 
-@@ -736,19 +765,28 @@ static int safexcel_hw_init(struct safex
- 	/* Clear any HIA interrupt */
- 	writel(GENMASK(30, 20), EIP197_HIA_AIC_G(priv) + EIP197_HIA_AIC_G_ACK);
- 
--	if (priv->flags & SAFEXCEL_HW_EIP197) {
--		eip197_trc_cache_init(priv);
--		priv->flags |= EIP197_TRC_CACHE;
-+	if (priv->flags & EIP197_SIMPLE_TRC) {
-+		writel(EIP197_STRC_CONFIG_INIT |
-+		       EIP197_STRC_CONFIG_LARGE_REC(EIP197_CS_TRC_REC_WC) |
-+		       EIP197_STRC_CONFIG_SMALL_REC(EIP197_CS_TRC_REC_WC),
-+		       priv->base + EIP197_STRC_CONFIG);
-+		writel(EIP197_PE_EIP96_TOKEN_CTRL2_CTX_DONE,
-+		       EIP197_PE(priv) + EIP197_PE_EIP96_TOKEN_CTRL2(0));
-+	} else if (priv->flags & SAFEXCEL_HW_EIP197) {
-+		ret = eip197_trc_cache_init(priv);
-+		if (ret)
-+			return ret;
-+	}
- 
-+	if (priv->flags & EIP197_ICE) {
- 		ret = eip197_load_firmwares(priv);
- 		if (ret)
- 			return ret;
- 	}
- 
--	safexcel_hw_setup_cdesc_rings(priv);
--	safexcel_hw_setup_rdesc_rings(priv);
--
--	return 0;
-+	return safexcel_hw_setup_cdesc_rings(priv) ?:
-+	       safexcel_hw_setup_rdesc_rings(priv) ?:
-+	       0;
- }
- 
- /* Called with ring's lock taken */
-@@ -836,20 +874,24 @@ finalize:
- 	spin_unlock_bh(&priv->ring[ring].lock);
- 
- 	/* let the RDR know we have pending descriptors */
--	writel((rdesc * priv->config.rd_offset) << 2,
-+	writel((rdesc * priv->config.rd_offset),
- 	       EIP197_HIA_RDR(priv, ring) + EIP197_HIA_xDR_PREP_COUNT);
- 
- 	/* let the CDR know we have pending descriptors */
--	writel((cdesc * priv->config.cd_offset) << 2,
-+	writel((cdesc * priv->config.cd_offset),
- 	       EIP197_HIA_CDR(priv, ring) + EIP197_HIA_xDR_PREP_COUNT);
- }
- 
- inline int safexcel_rdesc_check_errors(struct safexcel_crypto_priv *priv,
--				       struct safexcel_result_desc *rdesc)
-+				       void *rdp)
- {
--	if (likely((!rdesc->descriptor_overflow) &&
--		   (!rdesc->buffer_overflow) &&
--		   (!rdesc->result_data.error_code)))
-+	struct safexcel_result_desc *rdesc = rdp;
-+	struct result_data_desc *result_data = rdp + priv->config.res_offset;
-+
-+	if (likely((!rdesc->last_seg) || /* Rest only valid if last seg! */
-+		   ((!rdesc->descriptor_overflow) &&
-+		    (!rdesc->buffer_overflow) &&
-+		    (!result_data->error_code))))
- 		return 0;
- 
- 	if (rdesc->descriptor_overflow)
-@@ -858,13 +900,14 @@ inline int safexcel_rdesc_check_errors(s
- 	if (rdesc->buffer_overflow)
- 		dev_err(priv->dev, "Buffer overflow detected");
- 
--	if (rdesc->result_data.error_code & 0x4066) {
-+	if (result_data->error_code & 0x4066) {
- 		/* Fatal error (bits 1,2,5,6 & 14) */
- 		dev_err(priv->dev,
- 			"result descriptor error (%x)",
--			rdesc->result_data.error_code);
-+			result_data->error_code);
-+
- 		return -EIO;
--	} else if (rdesc->result_data.error_code &
-+	} else if (result_data->error_code &
- 		   (BIT(7) | BIT(4) | BIT(3) | BIT(0))) {
- 		/*
- 		 * Give priority over authentication fails:
-@@ -872,7 +915,7 @@ inline int safexcel_rdesc_check_errors(s
- 		 * something wrong with the input!
- 		 */
- 		return -EINVAL;
--	} else if (rdesc->result_data.error_code & BIT(9)) {
-+	} else if (result_data->error_code & BIT(9)) {
- 		/* Authentication failed */
- 		return -EBADMSG;
- 	}
-@@ -931,16 +974,18 @@ int safexcel_invalidate_cache(struct cry
- {
- 	struct safexcel_command_desc *cdesc;
- 	struct safexcel_result_desc *rdesc;
-+	struct safexcel_token  *dmmy;
- 	int ret = 0;
- 
- 	/* Prepare command descriptor */
--	cdesc = safexcel_add_cdesc(priv, ring, true, true, 0, 0, 0, ctxr_dma);
-+	cdesc = safexcel_add_cdesc(priv, ring, true, true, 0, 0, 0, ctxr_dma,
-+				   &dmmy);
- 	if (IS_ERR(cdesc))
- 		return PTR_ERR(cdesc);
- 
- 	cdesc->control_data.type = EIP197_TYPE_EXTENDED;
- 	cdesc->control_data.options = 0;
--	cdesc->control_data.refresh = 0;
-+	cdesc->control_data.context_lo &= ~EIP197_CONTEXT_SIZE_MASK;
- 	cdesc->control_data.control0 = CONTEXT_CONTROL_INV_TR;
- 
- 	/* Prepare result descriptor */
-@@ -1003,7 +1048,7 @@ handle_results:
- acknowledge:
- 	if (i)
- 		writel(EIP197_xDR_PROC_xD_PKT(i) |
--		       EIP197_xDR_PROC_xD_COUNT(tot_descs * priv->config.rd_offset),
-+		       (tot_descs * priv->config.rd_offset),
- 		       EIP197_HIA_RDR(priv, ring) + EIP197_HIA_xDR_PROC_COUNT);
- 
- 	/* If the number of requests overflowed the counter, try to proceed more
-@@ -1171,6 +1216,44 @@ static struct safexcel_alg_template *saf
- 	&safexcel_alg_xts_aes,
- 	&safexcel_alg_gcm,
- 	&safexcel_alg_ccm,
-+	&safexcel_alg_crc32,
-+	&safexcel_alg_cbcmac,
-+	&safexcel_alg_xcbcmac,
-+	&safexcel_alg_cmac,
-+	&safexcel_alg_chacha20,
-+	&safexcel_alg_chachapoly,
-+	&safexcel_alg_chachapoly_esp,
-+	&safexcel_alg_sm3,
-+	&safexcel_alg_hmac_sm3,
-+	&safexcel_alg_ecb_sm4,
-+	&safexcel_alg_cbc_sm4,
-+	&safexcel_alg_ofb_sm4,
-+	&safexcel_alg_cfb_sm4,
-+	&safexcel_alg_ctr_sm4,
-+	&safexcel_alg_authenc_hmac_sha1_cbc_sm4,
-+	&safexcel_alg_authenc_hmac_sm3_cbc_sm4,
-+	&safexcel_alg_authenc_hmac_sha1_ctr_sm4,
-+	&safexcel_alg_authenc_hmac_sm3_ctr_sm4,
-+	&safexcel_alg_sha3_224,
-+	&safexcel_alg_sha3_256,
-+	&safexcel_alg_sha3_384,
-+	&safexcel_alg_sha3_512,
-+	&safexcel_alg_hmac_sha3_224,
-+	&safexcel_alg_hmac_sha3_256,
-+	&safexcel_alg_hmac_sha3_384,
-+	&safexcel_alg_hmac_sha3_512,
-+	&safexcel_alg_authenc_hmac_sha1_cbc_des,
-+	&safexcel_alg_authenc_hmac_sha256_cbc_des3_ede,
-+	&safexcel_alg_authenc_hmac_sha224_cbc_des3_ede,
-+	&safexcel_alg_authenc_hmac_sha512_cbc_des3_ede,
-+	&safexcel_alg_authenc_hmac_sha384_cbc_des3_ede,
-+	&safexcel_alg_authenc_hmac_sha256_cbc_des,
-+	&safexcel_alg_authenc_hmac_sha224_cbc_des,
-+	&safexcel_alg_authenc_hmac_sha512_cbc_des,
-+	&safexcel_alg_authenc_hmac_sha384_cbc_des,
-+	&safexcel_alg_rfc4106_gcm,
-+	&safexcel_alg_rfc4543_gcm,
-+	&safexcel_alg_rfc4309_ccm,
- };
- 
- static int safexcel_register_algorithms(struct safexcel_crypto_priv *priv)
-@@ -1240,30 +1323,30 @@ static void safexcel_unregister_algorith
- 
- static void safexcel_configure(struct safexcel_crypto_priv *priv)
- {
--	u32 val, mask = 0;
--
--	val = readl(EIP197_HIA_AIC_G(priv) + EIP197_HIA_OPTIONS);
--
--	/* Read number of PEs from the engine */
--	if (priv->flags & SAFEXCEL_HW_EIP197)
--		/* Wider field width for all EIP197 type engines */
--		mask = EIP197_N_PES_MASK;
--	else
--		/* Narrow field width for EIP97 type engine */
--		mask = EIP97_N_PES_MASK;
--
--	priv->config.pes = (val >> EIP197_N_PES_OFFSET) & mask;
-+	u32 mask = BIT(priv->hwconfig.hwdataw) - 1;
- 
--	priv->config.rings = min_t(u32, val & GENMASK(3, 0), max_rings);
-+	priv->config.pes = priv->hwconfig.hwnumpes;
-+	priv->config.rings = min_t(u32, priv->hwconfig.hwnumrings, max_rings);
-+	/* Cannot currently support more rings than we have ring AICs! */
-+	priv->config.rings = min_t(u32, priv->config.rings,
-+					priv->hwconfig.hwnumraic);
- 
--	val = (val & GENMASK(27, 25)) >> 25;
--	mask = BIT(val) - 1;
--
--	priv->config.cd_size = (sizeof(struct safexcel_command_desc) / sizeof(u32));
-+	priv->config.cd_size = EIP197_CD64_FETCH_SIZE;
- 	priv->config.cd_offset = (priv->config.cd_size + mask) & ~mask;
-+	priv->config.cdsh_offset = (EIP197_MAX_TOKENS + mask) & ~mask;
- 
--	priv->config.rd_size = (sizeof(struct safexcel_result_desc) / sizeof(u32));
-+	/* res token is behind the descr, but ofs must be rounded to buswdth */
-+	priv->config.res_offset = (EIP197_RD64_FETCH_SIZE + mask) & ~mask;
-+	/* now the size of the descr is this 1st part plus the result struct */
-+	priv->config.rd_size    = priv->config.res_offset +
-+				  EIP197_RD64_RESULT_SIZE;
- 	priv->config.rd_offset = (priv->config.rd_size + mask) & ~mask;
-+
-+	/* convert dwords to bytes */
-+	priv->config.cd_offset *= sizeof(u32);
-+	priv->config.cdsh_offset *= sizeof(u32);
-+	priv->config.rd_offset *= sizeof(u32);
-+	priv->config.res_offset *= sizeof(u32);
- }
- 
- static void safexcel_init_register_offsets(struct safexcel_crypto_priv *priv)
-@@ -1309,7 +1392,7 @@ static int safexcel_probe_generic(void *
- 				  int is_pci_dev)
- {
- 	struct device *dev = priv->dev;
--	u32 peid, version, mask, val, hiaopt;
-+	u32 peid, version, mask, val, hiaopt, hwopt, peopt;
- 	int i, ret, hwctg;
- 
- 	priv->context_pool = dmam_pool_create("safexcel-context", dev,
-@@ -1371,13 +1454,16 @@ static int safexcel_probe_generic(void *
- 	 */
- 	version = readl(EIP197_GLOBAL(priv) + EIP197_VERSION);
- 	if (((priv->flags & SAFEXCEL_HW_EIP197) &&
--	     (EIP197_REG_LO16(version) != EIP197_VERSION_LE)) ||
-+	     (EIP197_REG_LO16(version) != EIP197_VERSION_LE) &&
-+	     (EIP197_REG_LO16(version) != EIP196_VERSION_LE)) ||
- 	    ((!(priv->flags & SAFEXCEL_HW_EIP197) &&
- 	     (EIP197_REG_LO16(version) != EIP97_VERSION_LE)))) {
- 		/*
- 		 * We did not find the device that matched our initial probing
- 		 * (or our initial probing failed) Report appropriate error.
- 		 */
-+		dev_err(priv->dev, "Probing for EIP97/EIP19x failed - no such device (read %08x)\n",
-+			version);
- 		return -ENODEV;
- 	}
- 
-@@ -1385,6 +1471,14 @@ static int safexcel_probe_generic(void *
- 	hwctg = version >> 28;
- 	peid = version & 255;
- 
-+	/* Detect EIP206 processing pipe */
-+	version = readl(EIP197_PE(priv) + + EIP197_PE_VERSION(0));
-+	if (EIP197_REG_LO16(version) != EIP206_VERSION_LE) {
-+		dev_err(priv->dev, "EIP%d: EIP206 not detected\n", peid);
-+		return -ENODEV;
-+	}
-+	priv->hwconfig.ppver = EIP197_VERSION_MASK(version);
-+
- 	/* Detect EIP96 packet engine and version */
- 	version = readl(EIP197_PE(priv) + EIP197_PE_EIP96_VERSION(0));
- 	if (EIP197_REG_LO16(version) != EIP96_VERSION_LE) {
-@@ -1393,10 +1487,13 @@ static int safexcel_probe_generic(void *
- 	}
- 	priv->hwconfig.pever = EIP197_VERSION_MASK(version);
- 
-+	hwopt = readl(EIP197_GLOBAL(priv) + EIP197_OPTIONS);
- 	hiaopt = readl(EIP197_HIA_AIC(priv) + EIP197_HIA_OPTIONS);
- 
- 	if (priv->flags & SAFEXCEL_HW_EIP197) {
- 		/* EIP197 */
-+		peopt = readl(EIP197_PE(priv) + EIP197_PE_OPTIONS(0));
-+
- 		priv->hwconfig.hwdataw  = (hiaopt >> EIP197_HWDATAW_OFFSET) &
- 					  EIP197_HWDATAW_MASK;
- 		priv->hwconfig.hwcfsize = ((hiaopt >> EIP197_CFSIZE_OFFSET) &
-@@ -1405,6 +1502,19 @@ static int safexcel_probe_generic(void *
- 		priv->hwconfig.hwrfsize = ((hiaopt >> EIP197_RFSIZE_OFFSET) &
- 					   EIP197_RFSIZE_MASK) +
- 					  EIP197_RFSIZE_ADJUST;
-+		priv->hwconfig.hwnumpes	= (hiaopt >> EIP197_N_PES_OFFSET) &
-+					  EIP197_N_PES_MASK;
-+		priv->hwconfig.hwnumrings = (hiaopt >> EIP197_N_RINGS_OFFSET) &
-+					    EIP197_N_RINGS_MASK;
-+		if (hiaopt & EIP197_HIA_OPT_HAS_PE_ARB)
-+			priv->flags |= EIP197_PE_ARB;
-+		if (EIP206_OPT_ICE_TYPE(peopt) == 1)
-+			priv->flags |= EIP197_ICE;
-+		/* If not a full TRC, then assume simple TRC */
-+		if (!(hwopt & EIP197_OPT_HAS_TRC))
-+			priv->flags |= EIP197_SIMPLE_TRC;
-+		/* EIP197 always has SOME form of TRC */
-+		priv->flags |= EIP197_TRC_CACHE;
- 	} else {
- 		/* EIP97 */
- 		priv->hwconfig.hwdataw  = (hiaopt >> EIP197_HWDATAW_OFFSET) &
-@@ -1413,6 +1523,23 @@ static int safexcel_probe_generic(void *
- 					  EIP97_CFSIZE_MASK;
- 		priv->hwconfig.hwrfsize = (hiaopt >> EIP97_RFSIZE_OFFSET) &
- 					  EIP97_RFSIZE_MASK;
-+		priv->hwconfig.hwnumpes	= 1; /* by definition */
-+		priv->hwconfig.hwnumrings = (hiaopt >> EIP197_N_RINGS_OFFSET) &
-+					    EIP197_N_RINGS_MASK;
-+	}
-+
-+	/* Scan for ring AIC's */
-+	for (i = 0; i < EIP197_MAX_RING_AIC; i++) {
-+		version = readl(EIP197_HIA_AIC_R(priv) +
-+				EIP197_HIA_AIC_R_VERSION(i));
-+		if (EIP197_REG_LO16(version) != EIP201_VERSION_LE)
-+			break;
-+	}
-+	priv->hwconfig.hwnumraic = i;
-+	/* Low-end EIP196 may not have any ring AIC's ... */
-+	if (!priv->hwconfig.hwnumraic) {
-+		dev_err(priv->dev, "No ring interrupt controller present!\n");
-+		return -ENODEV;
- 	}
- 
- 	/* Get supported algorithms from EIP96 transform engine */
-@@ -1420,10 +1547,12 @@ static int safexcel_probe_generic(void *
- 				    EIP197_PE_EIP96_OPTIONS(0));
- 
- 	/* Print single info line describing what we just detected */
--	dev_info(priv->dev, "EIP%d:%x(%d)-HIA:%x(%d,%d,%d),PE:%x,alg:%08x\n",
--		 peid, priv->hwconfig.hwver, hwctg, priv->hwconfig.hiaver,
--		 priv->hwconfig.hwdataw, priv->hwconfig.hwcfsize,
--		 priv->hwconfig.hwrfsize, priv->hwconfig.pever,
-+	dev_info(priv->dev, "EIP%d:%x(%d,%d,%d,%d)-HIA:%x(%d,%d,%d),PE:%x/%x,alg:%08x\n",
-+		 peid, priv->hwconfig.hwver, hwctg, priv->hwconfig.hwnumpes,
-+		 priv->hwconfig.hwnumrings, priv->hwconfig.hwnumraic,
-+		 priv->hwconfig.hiaver, priv->hwconfig.hwdataw,
-+		 priv->hwconfig.hwcfsize, priv->hwconfig.hwrfsize,
-+		 priv->hwconfig.ppver, priv->hwconfig.pever,
- 		 priv->hwconfig.algo_flags);
- 
- 	safexcel_configure(priv);
-@@ -1547,7 +1676,6 @@ static void safexcel_hw_reset_rings(stru
- 	}
- }
- 
--#if IS_ENABLED(CONFIG_OF)
- /* for Device Tree platform driver */
- 
- static int safexcel_probe(struct platform_device *pdev)
-@@ -1625,6 +1753,7 @@ static int safexcel_remove(struct platfo
- 	safexcel_unregister_algorithms(priv);
- 	safexcel_hw_reset_rings(priv);
- 
-+	clk_disable_unprepare(priv->reg_clk);
- 	clk_disable_unprepare(priv->clk);
- 
- 	for (i = 0; i < priv->config.rings; i++)
-@@ -1666,9 +1795,7 @@ static struct platform_driver  crypto_sa
- 		.of_match_table = safexcel_of_match_table,
- 	},
- };
--#endif
- 
--#if IS_ENABLED(CONFIG_PCI)
- /* PCIE devices - i.e. Inside Secure development boards */
- 
- static int safexcel_pci_probe(struct pci_dev *pdev,
-@@ -1759,7 +1886,7 @@ static int safexcel_pci_probe(struct pci
- 	return rc;
- }
- 
--void safexcel_pci_remove(struct pci_dev *pdev)
-+static void safexcel_pci_remove(struct pci_dev *pdev)
- {
- 	struct safexcel_crypto_priv *priv = pci_get_drvdata(pdev);
- 	int i;
-@@ -1789,54 +1916,32 @@ static struct pci_driver safexcel_pci_dr
- 	.probe         = safexcel_pci_probe,
- 	.remove        = safexcel_pci_remove,
- };
--#endif
--
--/* Unfortunately, we have to resort to global variables here */
--#if IS_ENABLED(CONFIG_PCI)
--int pcireg_rc = -EINVAL; /* Default safe value */
--#endif
--#if IS_ENABLED(CONFIG_OF)
--int ofreg_rc = -EINVAL; /* Default safe value */
--#endif
- 
- static int __init safexcel_init(void)
- {
--#if IS_ENABLED(CONFIG_PCI)
-+	int ret;
-+
- 	/* Register PCI driver */
--	pcireg_rc = pci_register_driver(&safexcel_pci_driver);
--#endif
-+	ret = pci_register_driver(&safexcel_pci_driver);
- 
--#if IS_ENABLED(CONFIG_OF)
- 	/* Register platform driver */
--	ofreg_rc = platform_driver_register(&crypto_safexcel);
-- #if IS_ENABLED(CONFIG_PCI)
--	/* Return success if either PCI or OF registered OK */
--	return pcireg_rc ? ofreg_rc : 0;
-- #else
--	return ofreg_rc;
-- #endif
--#else
-- #if IS_ENABLED(CONFIG_PCI)
--	return pcireg_rc;
-- #else
--	return -EINVAL;
-- #endif
--#endif
-+	if (IS_ENABLED(CONFIG_OF) && !ret) {
-+		ret = platform_driver_register(&crypto_safexcel);
-+		if (ret)
-+			pci_unregister_driver(&safexcel_pci_driver);
-+	}
-+
-+	return ret;
- }
- 
- static void __exit safexcel_exit(void)
- {
--#if IS_ENABLED(CONFIG_OF)
- 	/* Unregister platform driver */
--	if (!ofreg_rc)
-+	if (IS_ENABLED(CONFIG_OF))
- 		platform_driver_unregister(&crypto_safexcel);
--#endif
- 
--#if IS_ENABLED(CONFIG_PCI)
- 	/* Unregister PCI driver if successfully registered before */
--	if (!pcireg_rc)
--		pci_unregister_driver(&safexcel_pci_driver);
--#endif
-+	pci_unregister_driver(&safexcel_pci_driver);
- }
- 
- module_init(safexcel_init);
---- a/drivers/crypto/inside-secure/safexcel_cipher.c
-+++ b/drivers/crypto/inside-secure/safexcel_cipher.c
-@@ -5,18 +5,22 @@
-  * Antoine Tenart <antoine.tenart@free-electrons.com>
-  */
- 
-+#include <asm/unaligned.h>
- #include <linux/device.h>
- #include <linux/dma-mapping.h>
- #include <linux/dmapool.h>
--
- #include <crypto/aead.h>
- #include <crypto/aes.h>
- #include <crypto/authenc.h>
-+#include <crypto/chacha.h>
- #include <crypto/ctr.h>
- #include <crypto/internal/des.h>
- #include <crypto/gcm.h>
- #include <crypto/ghash.h>
-+#include <crypto/poly1305.h>
- #include <crypto/sha.h>
-+#include <crypto/sm3.h>
-+#include <crypto/sm4.h>
- #include <crypto/xts.h>
- #include <crypto/skcipher.h>
- #include <crypto/internal/aead.h>
-@@ -33,6 +37,8 @@ enum safexcel_cipher_alg {
- 	SAFEXCEL_DES,
- 	SAFEXCEL_3DES,
- 	SAFEXCEL_AES,
-+	SAFEXCEL_CHACHA20,
-+	SAFEXCEL_SM4,
- };
- 
- struct safexcel_cipher_ctx {
-@@ -41,8 +47,12 @@ struct safexcel_cipher_ctx {
- 
- 	u32 mode;
- 	enum safexcel_cipher_alg alg;
--	bool aead;
--	int  xcm; /* 0=authenc, 1=GCM, 2 reserved for CCM */
-+	u8 aead; /* !=0=AEAD, 2=IPSec ESP AEAD, 3=IPsec ESP GMAC */
-+	u8 xcm;  /* 0=authenc, 1=GCM, 2 reserved for CCM */
-+	u8 aadskip;
-+	u8 blocksz;
-+	u32 ivmask;
-+	u32 ctrinit;
- 
- 	__le32 key[16];
- 	u32 nonce;
-@@ -51,10 +61,11 @@ struct safexcel_cipher_ctx {
- 	/* All the below is AEAD specific */
- 	u32 hash_alg;
- 	u32 state_sz;
--	u32 ipad[SHA512_DIGEST_SIZE / sizeof(u32)];
--	u32 opad[SHA512_DIGEST_SIZE / sizeof(u32)];
-+	__be32 ipad[SHA512_DIGEST_SIZE / sizeof(u32)];
-+	__be32 opad[SHA512_DIGEST_SIZE / sizeof(u32)];
- 
- 	struct crypto_cipher *hkaes;
-+	struct crypto_aead *fback;
- };
- 
- struct safexcel_cipher_req {
-@@ -65,206 +76,298 @@ struct safexcel_cipher_req {
- 	int  nr_src, nr_dst;
- };
- 
--static void safexcel_cipher_token(struct safexcel_cipher_ctx *ctx, u8 *iv,
--				  struct safexcel_command_desc *cdesc)
-+static int safexcel_skcipher_iv(struct safexcel_cipher_ctx *ctx, u8 *iv,
-+				struct safexcel_command_desc *cdesc)
- {
--	u32 block_sz = 0;
--
- 	if (ctx->mode == CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD) {
- 		cdesc->control_data.options |= EIP197_OPTION_4_TOKEN_IV_CMD;
--
- 		/* 32 bit nonce */
- 		cdesc->control_data.token[0] = ctx->nonce;
- 		/* 64 bit IV part */
- 		memcpy(&cdesc->control_data.token[1], iv, 8);
--		/* 32 bit counter, start at 1 (big endian!) */
--		cdesc->control_data.token[3] = cpu_to_be32(1);
--
--		return;
--	} else if (ctx->xcm == EIP197_XCM_MODE_GCM) {
--		cdesc->control_data.options |= EIP197_OPTION_4_TOKEN_IV_CMD;
--
--		/* 96 bit IV part */
--		memcpy(&cdesc->control_data.token[0], iv, 12);
--		/* 32 bit counter, start at 1 (big endian!) */
--		cdesc->control_data.token[3] = cpu_to_be32(1);
--
--		return;
--	} else if (ctx->xcm == EIP197_XCM_MODE_CCM) {
-+		/* 32 bit counter, start at 0 or 1 (big endian!) */
-+		cdesc->control_data.token[3] =
-+			(__force u32)cpu_to_be32(ctx->ctrinit);
-+		return 4;
-+	}
-+	if (ctx->alg == SAFEXCEL_CHACHA20) {
- 		cdesc->control_data.options |= EIP197_OPTION_4_TOKEN_IV_CMD;
--
--		/* Variable length IV part */
--		memcpy(&cdesc->control_data.token[0], iv, 15 - iv[0]);
--		/* Start variable length counter at 0 */
--		memset((u8 *)&cdesc->control_data.token[0] + 15 - iv[0],
--		       0, iv[0] + 1);
--
--		return;
-+		/* 96 bit nonce part */
-+		memcpy(&cdesc->control_data.token[0], &iv[4], 12);
-+		/* 32 bit counter */
-+		cdesc->control_data.token[3] = *(u32 *)iv;
-+		return 4;
- 	}
- 
--	if (ctx->mode != CONTEXT_CONTROL_CRYPTO_MODE_ECB) {
--		switch (ctx->alg) {
--		case SAFEXCEL_DES:
--			block_sz = DES_BLOCK_SIZE;
--			cdesc->control_data.options |= EIP197_OPTION_2_TOKEN_IV_CMD;
--			break;
--		case SAFEXCEL_3DES:
--			block_sz = DES3_EDE_BLOCK_SIZE;
--			cdesc->control_data.options |= EIP197_OPTION_2_TOKEN_IV_CMD;
--			break;
--		case SAFEXCEL_AES:
--			block_sz = AES_BLOCK_SIZE;
--			cdesc->control_data.options |= EIP197_OPTION_4_TOKEN_IV_CMD;
--			break;
--		}
--		memcpy(cdesc->control_data.token, iv, block_sz);
--	}
-+	cdesc->control_data.options |= ctx->ivmask;
-+	memcpy(cdesc->control_data.token, iv, ctx->blocksz);
-+	return ctx->blocksz / sizeof(u32);
- }
- 
- static void safexcel_skcipher_token(struct safexcel_cipher_ctx *ctx, u8 *iv,
- 				    struct safexcel_command_desc *cdesc,
-+				    struct safexcel_token *atoken,
- 				    u32 length)
- {
- 	struct safexcel_token *token;
-+	int ivlen;
- 
--	safexcel_cipher_token(ctx, iv, cdesc);
--
--	/* skip over worst case IV of 4 dwords, no need to be exact */
--	token = (struct safexcel_token *)(cdesc->control_data.token + 4);
-+	ivlen = safexcel_skcipher_iv(ctx, iv, cdesc);
-+	if (ivlen == 4) {
-+		/* No space in cdesc, instruction moves to atoken */
-+		cdesc->additional_cdata_size = 1;
-+		token = atoken;
-+	} else {
-+		/* Everything fits in cdesc */
-+		token = (struct safexcel_token *)(cdesc->control_data.token + 2);
-+		/* Need to pad with NOP */
-+		eip197_noop_token(&token[1]);
-+	}
-+
-+	token->opcode = EIP197_TOKEN_OPCODE_DIRECTION;
-+	token->packet_length = length;
-+	token->stat = EIP197_TOKEN_STAT_LAST_PACKET |
-+		      EIP197_TOKEN_STAT_LAST_HASH;
-+	token->instructions = EIP197_TOKEN_INS_LAST |
-+			      EIP197_TOKEN_INS_TYPE_CRYPTO |
-+			      EIP197_TOKEN_INS_TYPE_OUTPUT;
-+}
- 
--	token[0].opcode = EIP197_TOKEN_OPCODE_DIRECTION;
--	token[0].packet_length = length;
--	token[0].stat = EIP197_TOKEN_STAT_LAST_PACKET |
--			EIP197_TOKEN_STAT_LAST_HASH;
--	token[0].instructions = EIP197_TOKEN_INS_LAST |
--				EIP197_TOKEN_INS_TYPE_CRYPTO |
--				EIP197_TOKEN_INS_TYPE_OUTPUT;
-+static void safexcel_aead_iv(struct safexcel_cipher_ctx *ctx, u8 *iv,
-+			     struct safexcel_command_desc *cdesc)
-+{
-+	if (ctx->mode == CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD ||
-+	    ctx->aead & EIP197_AEAD_TYPE_IPSEC_ESP) { /* _ESP and _ESP_GMAC */
-+		/* 32 bit nonce */
-+		cdesc->control_data.token[0] = ctx->nonce;
-+		/* 64 bit IV part */
-+		memcpy(&cdesc->control_data.token[1], iv, 8);
-+		/* 32 bit counter, start at 0 or 1 (big endian!) */
-+		cdesc->control_data.token[3] =
-+			(__force u32)cpu_to_be32(ctx->ctrinit);
-+		return;
-+	}
-+	if (ctx->xcm == EIP197_XCM_MODE_GCM || ctx->alg == SAFEXCEL_CHACHA20) {
-+		/* 96 bit IV part */
-+		memcpy(&cdesc->control_data.token[0], iv, 12);
-+		/* 32 bit counter, start at 0 or 1 (big endian!) */
-+		cdesc->control_data.token[3] =
-+			(__force u32)cpu_to_be32(ctx->ctrinit);
-+		return;
-+	}
-+	/* CBC */
-+	memcpy(cdesc->control_data.token, iv, ctx->blocksz);
- }
- 
- static void safexcel_aead_token(struct safexcel_cipher_ctx *ctx, u8 *iv,
- 				struct safexcel_command_desc *cdesc,
-+				struct safexcel_token *atoken,
- 				enum safexcel_cipher_direction direction,
- 				u32 cryptlen, u32 assoclen, u32 digestsize)
- {
--	struct safexcel_token *token;
-+	struct safexcel_token *aadref;
-+	int atoksize = 2; /* Start with minimum size */
-+	int assocadj = assoclen - ctx->aadskip, aadalign;
- 
--	safexcel_cipher_token(ctx, iv, cdesc);
-+	/* Always 4 dwords of embedded IV  for AEAD modes */
-+	cdesc->control_data.options |= EIP197_OPTION_4_TOKEN_IV_CMD;
- 
--	if (direction == SAFEXCEL_ENCRYPT) {
--		/* align end of instruction sequence to end of token */
--		token = (struct safexcel_token *)(cdesc->control_data.token +
--			 EIP197_MAX_TOKENS - 13);
--
--		token[12].opcode = EIP197_TOKEN_OPCODE_INSERT;
--		token[12].packet_length = digestsize;
--		token[12].stat = EIP197_TOKEN_STAT_LAST_HASH |
--				 EIP197_TOKEN_STAT_LAST_PACKET;
--		token[12].instructions = EIP197_TOKEN_INS_TYPE_OUTPUT |
--					 EIP197_TOKEN_INS_INSERT_HASH_DIGEST;
--	} else {
-+	if (direction == SAFEXCEL_DECRYPT)
- 		cryptlen -= digestsize;
- 
--		/* align end of instruction sequence to end of token */
--		token = (struct safexcel_token *)(cdesc->control_data.token +
--			 EIP197_MAX_TOKENS - 14);
--
--		token[12].opcode = EIP197_TOKEN_OPCODE_RETRIEVE;
--		token[12].packet_length = digestsize;
--		token[12].stat = EIP197_TOKEN_STAT_LAST_HASH |
--				 EIP197_TOKEN_STAT_LAST_PACKET;
--		token[12].instructions = EIP197_TOKEN_INS_INSERT_HASH_DIGEST;
--
--		token[13].opcode = EIP197_TOKEN_OPCODE_VERIFY;
--		token[13].packet_length = digestsize |
--					  EIP197_TOKEN_HASH_RESULT_VERIFY;
--		token[13].stat = EIP197_TOKEN_STAT_LAST_HASH |
--				 EIP197_TOKEN_STAT_LAST_PACKET;
--		token[13].instructions = EIP197_TOKEN_INS_TYPE_OUTPUT;
--	}
--
--	token[6].opcode = EIP197_TOKEN_OPCODE_DIRECTION;
--	token[6].packet_length = assoclen;
--
--	if (likely(cryptlen)) {
--		token[6].instructions = EIP197_TOKEN_INS_TYPE_HASH;
--
--		token[10].opcode = EIP197_TOKEN_OPCODE_DIRECTION;
--		token[10].packet_length = cryptlen;
--		token[10].stat = EIP197_TOKEN_STAT_LAST_HASH;
--		token[10].instructions = EIP197_TOKEN_INS_LAST |
--					 EIP197_TOKEN_INS_TYPE_CRYPTO |
--					 EIP197_TOKEN_INS_TYPE_HASH |
--					 EIP197_TOKEN_INS_TYPE_OUTPUT;
--	} else if (ctx->xcm != EIP197_XCM_MODE_CCM) {
--		token[6].stat = EIP197_TOKEN_STAT_LAST_HASH;
--		token[6].instructions = EIP197_TOKEN_INS_LAST |
--					EIP197_TOKEN_INS_TYPE_HASH;
--	}
--
--	if (!ctx->xcm)
--		return;
--
--	token[8].opcode = EIP197_TOKEN_OPCODE_INSERT_REMRES;
--	token[8].packet_length = 0;
--	token[8].instructions = AES_BLOCK_SIZE;
--
--	token[9].opcode = EIP197_TOKEN_OPCODE_INSERT;
--	token[9].packet_length = AES_BLOCK_SIZE;
--	token[9].instructions = EIP197_TOKEN_INS_TYPE_OUTPUT |
--				EIP197_TOKEN_INS_TYPE_CRYPTO;
--
--	if (ctx->xcm == EIP197_XCM_MODE_GCM) {
--		token[6].instructions = EIP197_TOKEN_INS_LAST |
--					EIP197_TOKEN_INS_TYPE_HASH;
--	} else {
--		u8 *cbcmaciv = (u8 *)&token[1];
--		u32 *aadlen = (u32 *)&token[5];
--
-+	if (unlikely(ctx->xcm == EIP197_XCM_MODE_CCM)) {
- 		/* Construct IV block B0 for the CBC-MAC */
--		token[0].opcode = EIP197_TOKEN_OPCODE_INSERT;
--		token[0].packet_length = AES_BLOCK_SIZE +
--					 ((assoclen > 0) << 1);
--		token[0].instructions = EIP197_TOKEN_INS_ORIGIN_TOKEN |
--					EIP197_TOKEN_INS_TYPE_HASH;
--		/* Variable length IV part */
--		memcpy(cbcmaciv, iv, 15 - iv[0]);
--		/* fixup flags byte */
--		cbcmaciv[0] |= ((assoclen > 0) << 6) | ((digestsize - 2) << 2);
--		/* Clear upper bytes of variable message length to 0 */
--		memset(cbcmaciv + 15 - iv[0], 0, iv[0] - 1);
--		/* insert lower 2 bytes of message length */
--		cbcmaciv[14] = cryptlen >> 8;
--		cbcmaciv[15] = cryptlen & 255;
--
--		if (assoclen) {
--			*aadlen = cpu_to_le32(cpu_to_be16(assoclen));
--			assoclen += 2;
-+		u8 *final_iv = (u8 *)cdesc->control_data.token;
-+		u8 *cbcmaciv = (u8 *)&atoken[1];
-+		__le32 *aadlen = (__le32 *)&atoken[5];
-+
-+		if (ctx->aead == EIP197_AEAD_TYPE_IPSEC_ESP) {
-+			/* Length + nonce */
-+			cdesc->control_data.token[0] = ctx->nonce;
-+			/* Fixup flags byte */
-+			*(__le32 *)cbcmaciv =
-+				cpu_to_le32(ctx->nonce |
-+					    ((assocadj > 0) << 6) |
-+					    ((digestsize - 2) << 2));
-+			/* 64 bit IV part */
-+			memcpy(&cdesc->control_data.token[1], iv, 8);
-+			memcpy(cbcmaciv + 4, iv, 8);
-+			/* Start counter at 0 */
-+			cdesc->control_data.token[3] = 0;
-+			/* Message length */
-+			*(__be32 *)(cbcmaciv + 12) = cpu_to_be32(cryptlen);
-+		} else {
-+			/* Variable length IV part */
-+			memcpy(final_iv, iv, 15 - iv[0]);
-+			memcpy(cbcmaciv, iv, 15 - iv[0]);
-+			/* Start variable length counter at 0 */
-+			memset(final_iv + 15 - iv[0], 0, iv[0] + 1);
-+			memset(cbcmaciv + 15 - iv[0], 0, iv[0] - 1);
-+			/* fixup flags byte */
-+			cbcmaciv[0] |= ((assocadj > 0) << 6) |
-+				       ((digestsize - 2) << 2);
-+			/* insert lower 2 bytes of message length */
-+			cbcmaciv[14] = cryptlen >> 8;
-+			cbcmaciv[15] = cryptlen & 255;
-+		}
-+
-+		atoken->opcode = EIP197_TOKEN_OPCODE_INSERT;
-+		atoken->packet_length = AES_BLOCK_SIZE +
-+					((assocadj > 0) << 1);
-+		atoken->stat = 0;
-+		atoken->instructions = EIP197_TOKEN_INS_ORIGIN_TOKEN |
-+				       EIP197_TOKEN_INS_TYPE_HASH;
-+
-+		if (likely(assocadj)) {
-+			*aadlen = cpu_to_le32((assocadj >> 8) |
-+					      (assocadj & 255) << 8);
-+			atoken += 6;
-+			atoksize += 7;
-+		} else {
-+			atoken += 5;
-+			atoksize += 6;
- 		}
- 
--		token[6].instructions = EIP197_TOKEN_INS_TYPE_HASH;
--
--		/* Align AAD data towards hash engine */
--		token[7].opcode = EIP197_TOKEN_OPCODE_INSERT;
--		assoclen &= 15;
--		token[7].packet_length = assoclen ? 16 - assoclen : 0;
--
-+		/* Process AAD data */
-+		aadref = atoken;
-+		atoken->opcode = EIP197_TOKEN_OPCODE_DIRECTION;
-+		atoken->packet_length = assocadj;
-+		atoken->stat = 0;
-+		atoken->instructions = EIP197_TOKEN_INS_TYPE_HASH;
-+		atoken++;
-+
-+		/* For CCM only, align AAD data towards hash engine */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_INSERT;
-+		aadalign = (assocadj + 2) & 15;
-+		atoken->packet_length = assocadj && aadalign ?
-+						16 - aadalign :
-+						0;
- 		if (likely(cryptlen)) {
--			token[7].instructions = EIP197_TOKEN_INS_TYPE_HASH;
--
--			/* Align crypto data towards hash engine */
--			token[10].stat = 0;
-+			atoken->stat = 0;
-+			atoken->instructions = EIP197_TOKEN_INS_TYPE_HASH;
-+		} else {
-+			atoken->stat = EIP197_TOKEN_STAT_LAST_HASH;
-+			atoken->instructions = EIP197_TOKEN_INS_LAST |
-+					       EIP197_TOKEN_INS_TYPE_HASH;
-+		}
-+	} else {
-+		safexcel_aead_iv(ctx, iv, cdesc);
- 
--			token[11].opcode = EIP197_TOKEN_OPCODE_INSERT;
--			cryptlen &= 15;
--			token[11].packet_length = cryptlen ? 16 - cryptlen : 0;
--			token[11].stat = EIP197_TOKEN_STAT_LAST_HASH;
--			token[11].instructions = EIP197_TOKEN_INS_TYPE_HASH;
-+		/* Process AAD data */
-+		aadref = atoken;
-+		atoken->opcode = EIP197_TOKEN_OPCODE_DIRECTION;
-+		atoken->packet_length = assocadj;
-+		atoken->stat = EIP197_TOKEN_STAT_LAST_HASH;
-+		atoken->instructions = EIP197_TOKEN_INS_LAST |
-+				       EIP197_TOKEN_INS_TYPE_HASH;
-+	}
-+	atoken++;
-+
-+	if (ctx->aead == EIP197_AEAD_TYPE_IPSEC_ESP) {
-+		/* For ESP mode (and not GMAC), skip over the IV */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_DIRECTION;
-+		atoken->packet_length = EIP197_AEAD_IPSEC_IV_SIZE;
-+		atoken->stat = 0;
-+		atoken->instructions = 0;
-+		atoken++;
-+		atoksize++;
-+	} else if (unlikely(ctx->alg == SAFEXCEL_CHACHA20 &&
-+			    direction == SAFEXCEL_DECRYPT)) {
-+		/* Poly-chacha decryption needs a dummy NOP here ... */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_INSERT;
-+		atoken->packet_length = 16; /* According to Op Manual */
-+		atoken->stat = 0;
-+		atoken->instructions = 0;
-+		atoken++;
-+		atoksize++;
-+	}
-+
-+	if  (ctx->xcm) {
-+		/* For GCM and CCM, obtain enc(Y0) */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_INSERT_REMRES;
-+		atoken->packet_length = 0;
-+		atoken->stat = 0;
-+		atoken->instructions = AES_BLOCK_SIZE;
-+		atoken++;
-+
-+		atoken->opcode = EIP197_TOKEN_OPCODE_INSERT;
-+		atoken->packet_length = AES_BLOCK_SIZE;
-+		atoken->stat = 0;
-+		atoken->instructions = EIP197_TOKEN_INS_TYPE_OUTPUT |
-+				       EIP197_TOKEN_INS_TYPE_CRYPTO;
-+		atoken++;
-+		atoksize += 2;
-+	}
-+
-+	if (likely(cryptlen || ctx->alg == SAFEXCEL_CHACHA20)) {
-+		/* Fixup stat field for AAD direction instruction */
-+		aadref->stat = 0;
-+
-+		/* Process crypto data */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_DIRECTION;
-+		atoken->packet_length = cryptlen;
-+
-+		if (unlikely(ctx->aead == EIP197_AEAD_TYPE_IPSEC_ESP_GMAC)) {
-+			/* Fixup instruction field for AAD dir instruction */
-+			aadref->instructions = EIP197_TOKEN_INS_TYPE_HASH;
-+
-+			/* Do not send to crypt engine in case of GMAC */
-+			atoken->instructions = EIP197_TOKEN_INS_LAST |
-+					       EIP197_TOKEN_INS_TYPE_HASH |
-+					       EIP197_TOKEN_INS_TYPE_OUTPUT;
-+		} else {
-+			atoken->instructions = EIP197_TOKEN_INS_LAST |
-+					       EIP197_TOKEN_INS_TYPE_CRYPTO |
-+					       EIP197_TOKEN_INS_TYPE_HASH |
-+					       EIP197_TOKEN_INS_TYPE_OUTPUT;
-+		}
-+
-+		cryptlen &= 15;
-+		if (unlikely(ctx->xcm == EIP197_XCM_MODE_CCM && cryptlen)) {
-+			atoken->stat = 0;
-+			/* For CCM only, pad crypto data to the hash engine */
-+			atoken++;
-+			atoksize++;
-+			atoken->opcode = EIP197_TOKEN_OPCODE_INSERT;
-+			atoken->packet_length = 16 - cryptlen;
-+			atoken->stat = EIP197_TOKEN_STAT_LAST_HASH;
-+			atoken->instructions = EIP197_TOKEN_INS_TYPE_HASH;
- 		} else {
--			token[7].stat = EIP197_TOKEN_STAT_LAST_HASH;
--			token[7].instructions = EIP197_TOKEN_INS_LAST |
--						EIP197_TOKEN_INS_TYPE_HASH;
-+			atoken->stat = EIP197_TOKEN_STAT_LAST_HASH;
- 		}
-+		atoken++;
-+		atoksize++;
- 	}
-+
-+	if (direction == SAFEXCEL_ENCRYPT) {
-+		/* Append ICV */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_INSERT;
-+		atoken->packet_length = digestsize;
-+		atoken->stat = EIP197_TOKEN_STAT_LAST_HASH |
-+			       EIP197_TOKEN_STAT_LAST_PACKET;
-+		atoken->instructions = EIP197_TOKEN_INS_TYPE_OUTPUT |
-+				       EIP197_TOKEN_INS_INSERT_HASH_DIGEST;
-+	} else {
-+		/* Extract ICV */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_RETRIEVE;
-+		atoken->packet_length = digestsize;
-+		atoken->stat = EIP197_TOKEN_STAT_LAST_HASH |
-+			       EIP197_TOKEN_STAT_LAST_PACKET;
-+		atoken->instructions = EIP197_TOKEN_INS_INSERT_HASH_DIGEST;
-+		atoken++;
-+		atoksize++;
-+
-+		/* Verify ICV */
-+		atoken->opcode = EIP197_TOKEN_OPCODE_VERIFY;
-+		atoken->packet_length = digestsize |
-+					EIP197_TOKEN_HASH_RESULT_VERIFY;
-+		atoken->stat = EIP197_TOKEN_STAT_LAST_HASH |
-+			       EIP197_TOKEN_STAT_LAST_PACKET;
-+		atoken->instructions = EIP197_TOKEN_INS_TYPE_OUTPUT;
-+	}
-+
-+	/* Fixup length of the token in the command descriptor */
-+	cdesc->additional_cdata_size = atoksize;
- }
- 
- static int safexcel_skcipher_aes_setkey(struct crypto_skcipher *ctfm,
-@@ -277,14 +380,12 @@ static int safexcel_skcipher_aes_setkey(
- 	int ret, i;
- 
- 	ret = aes_expandkey(&aes, key, len);
--	if (ret) {
--		crypto_skcipher_set_flags(ctfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
-+	if (ret)
- 		return ret;
--	}
- 
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
- 		for (i = 0; i < len / sizeof(u32); i++) {
--			if (ctx->key[i] != cpu_to_le32(aes.key_enc[i])) {
-+			if (le32_to_cpu(ctx->key[i]) != aes.key_enc[i]) {
- 				ctx->base.needs_inv = true;
- 				break;
- 			}
-@@ -309,43 +410,57 @@ static int safexcel_aead_setkey(struct c
- 	struct safexcel_crypto_priv *priv = ctx->priv;
- 	struct crypto_authenc_keys keys;
- 	struct crypto_aes_ctx aes;
--	int err = -EINVAL;
-+	int err = -EINVAL, i;
- 
--	if (crypto_authenc_extractkeys(&keys, key, len) != 0)
-+	if (unlikely(crypto_authenc_extractkeys(&keys, key, len)))
- 		goto badkey;
- 
- 	if (ctx->mode == CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD) {
--		/* Minimum keysize is minimum AES key size + nonce size */
--		if (keys.enckeylen < (AES_MIN_KEY_SIZE +
--				      CTR_RFC3686_NONCE_SIZE))
-+		/* Must have at least space for the nonce here */
-+		if (unlikely(keys.enckeylen < CTR_RFC3686_NONCE_SIZE))
- 			goto badkey;
- 		/* last 4 bytes of key are the nonce! */
- 		ctx->nonce = *(u32 *)(keys.enckey + keys.enckeylen -
- 				      CTR_RFC3686_NONCE_SIZE);
- 		/* exclude the nonce here */
--		keys.enckeylen -= CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD;
-+		keys.enckeylen -= CTR_RFC3686_NONCE_SIZE;
- 	}
- 
- 	/* Encryption key */
- 	switch (ctx->alg) {
-+	case SAFEXCEL_DES:
-+		err = verify_aead_des_key(ctfm, keys.enckey, keys.enckeylen);
-+		if (unlikely(err))
-+			goto badkey;
-+		break;
- 	case SAFEXCEL_3DES:
- 		err = verify_aead_des3_key(ctfm, keys.enckey, keys.enckeylen);
- 		if (unlikely(err))
--			goto badkey_expflags;
-+			goto badkey;
- 		break;
- 	case SAFEXCEL_AES:
- 		err = aes_expandkey(&aes, keys.enckey, keys.enckeylen);
- 		if (unlikely(err))
- 			goto badkey;
- 		break;
-+	case SAFEXCEL_SM4:
-+		if (unlikely(keys.enckeylen != SM4_KEY_SIZE))
-+			goto badkey;
-+		break;
- 	default:
- 		dev_err(priv->dev, "aead: unsupported cipher algorithm\n");
- 		goto badkey;
- 	}
- 
--	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma &&
--	    memcmp(ctx->key, keys.enckey, keys.enckeylen))
--		ctx->base.needs_inv = true;
-+	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
-+		for (i = 0; i < keys.enckeylen / sizeof(u32); i++) {
-+			if (le32_to_cpu(ctx->key[i]) !=
-+			    ((u32 *)keys.enckey)[i]) {
-+				ctx->base.needs_inv = true;
-+				break;
-+			}
-+		}
-+	}
- 
- 	/* Auth key */
- 	switch (ctx->hash_alg) {
-@@ -374,21 +489,24 @@ static int safexcel_aead_setkey(struct c
- 					 keys.authkeylen, &istate, &ostate))
- 			goto badkey;
- 		break;
-+	case CONTEXT_CONTROL_CRYPTO_ALG_SM3:
-+		if (safexcel_hmac_setkey("safexcel-sm3", keys.authkey,
-+					 keys.authkeylen, &istate, &ostate))
-+			goto badkey;
-+		break;
- 	default:
- 		dev_err(priv->dev, "aead: unsupported hash algorithm\n");
- 		goto badkey;
- 	}
- 
--	crypto_aead_set_flags(ctfm, crypto_aead_get_flags(ctfm) &
--				    CRYPTO_TFM_RES_MASK);
--
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma &&
- 	    (memcmp(ctx->ipad, istate.state, ctx->state_sz) ||
- 	     memcmp(ctx->opad, ostate.state, ctx->state_sz)))
- 		ctx->base.needs_inv = true;
- 
- 	/* Now copy the keys into the context */
--	memcpy(ctx->key, keys.enckey, keys.enckeylen);
-+	for (i = 0; i < keys.enckeylen / sizeof(u32); i++)
-+		ctx->key[i] = cpu_to_le32(((u32 *)keys.enckey)[i]);
- 	ctx->key_len = keys.enckeylen;
- 
- 	memcpy(ctx->ipad, &istate.state, ctx->state_sz);
-@@ -398,8 +516,6 @@ static int safexcel_aead_setkey(struct c
- 	return 0;
- 
- badkey:
--	crypto_aead_set_flags(ctfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
--badkey_expflags:
- 	memzero_explicit(&keys, sizeof(keys));
- 	return err;
- }
-@@ -423,6 +539,17 @@ static int safexcel_context_control(stru
- 				CONTEXT_CONTROL_DIGEST_XCM |
- 				ctx->hash_alg |
- 				CONTEXT_CONTROL_SIZE(ctrl_size);
-+		} else if (ctx->alg == SAFEXCEL_CHACHA20) {
-+			/* Chacha20-Poly1305 */
-+			cdesc->control_data.control0 =
-+				CONTEXT_CONTROL_KEY_EN |
-+				CONTEXT_CONTROL_CRYPTO_ALG_CHACHA20 |
-+				(sreq->direction == SAFEXCEL_ENCRYPT ?
-+					CONTEXT_CONTROL_TYPE_ENCRYPT_HASH_OUT :
-+					CONTEXT_CONTROL_TYPE_HASH_DECRYPT_IN) |
-+				ctx->hash_alg |
-+				CONTEXT_CONTROL_SIZE(ctrl_size);
-+			return 0;
- 		} else {
- 			ctrl_size += ctx->state_sz / sizeof(u32) * 2;
- 			cdesc->control_data.control0 =
-@@ -431,17 +558,21 @@ static int safexcel_context_control(stru
- 				ctx->hash_alg |
- 				CONTEXT_CONTROL_SIZE(ctrl_size);
- 		}
--		if (sreq->direction == SAFEXCEL_ENCRYPT)
--			cdesc->control_data.control0 |=
--				(ctx->xcm == EIP197_XCM_MODE_CCM) ?
--					CONTEXT_CONTROL_TYPE_HASH_ENCRYPT_OUT :
--					CONTEXT_CONTROL_TYPE_ENCRYPT_HASH_OUT;
- 
-+		if (sreq->direction == SAFEXCEL_ENCRYPT &&
-+		    (ctx->xcm == EIP197_XCM_MODE_CCM ||
-+		     ctx->aead == EIP197_AEAD_TYPE_IPSEC_ESP_GMAC))
-+			cdesc->control_data.control0 |=
-+				CONTEXT_CONTROL_TYPE_HASH_ENCRYPT_OUT;
-+		else if (sreq->direction == SAFEXCEL_ENCRYPT)
-+			cdesc->control_data.control0 |=
-+				CONTEXT_CONTROL_TYPE_ENCRYPT_HASH_OUT;
-+		else if (ctx->xcm == EIP197_XCM_MODE_CCM)
-+			cdesc->control_data.control0 |=
-+				CONTEXT_CONTROL_TYPE_DECRYPT_HASH_IN;
- 		else
- 			cdesc->control_data.control0 |=
--				(ctx->xcm == EIP197_XCM_MODE_CCM) ?
--					CONTEXT_CONTROL_TYPE_DECRYPT_HASH_IN :
--					CONTEXT_CONTROL_TYPE_HASH_DECRYPT_IN;
-+				CONTEXT_CONTROL_TYPE_HASH_DECRYPT_IN;
- 	} else {
- 		if (sreq->direction == SAFEXCEL_ENCRYPT)
- 			cdesc->control_data.control0 =
-@@ -480,6 +611,12 @@ static int safexcel_context_control(stru
- 				ctx->key_len >> ctx->xts);
- 			return -EINVAL;
- 		}
-+	} else if (ctx->alg == SAFEXCEL_CHACHA20) {
-+		cdesc->control_data.control0 |=
-+			CONTEXT_CONTROL_CRYPTO_ALG_CHACHA20;
-+	} else if (ctx->alg == SAFEXCEL_SM4) {
-+		cdesc->control_data.control0 |=
-+			CONTEXT_CONTROL_CRYPTO_ALG_SM4;
- 	}
- 
- 	return 0;
-@@ -563,6 +700,7 @@ static int safexcel_send_req(struct cryp
- 	unsigned int totlen;
- 	unsigned int totlen_src = cryptlen + assoclen;
- 	unsigned int totlen_dst = totlen_src;
-+	struct safexcel_token *atoken;
- 	int n_cdesc = 0, n_rdesc = 0;
- 	int queued, i, ret = 0;
- 	bool first = true;
-@@ -637,56 +775,60 @@ static int safexcel_send_req(struct cryp
- 
- 	memcpy(ctx->base.ctxr->data, ctx->key, ctx->key_len);
- 
--	/* The EIP cannot deal with zero length input packets! */
--	if (totlen == 0)
--		totlen = 1;
-+	if (!totlen) {
-+		/*
-+		 * The EIP97 cannot deal with zero length input packets!
-+		 * So stuff a dummy command descriptor indicating a 1 byte
-+		 * (dummy) input packet, using the context record as source.
-+		 */
-+		first_cdesc = safexcel_add_cdesc(priv, ring,
-+						 1, 1, ctx->base.ctxr_dma,
-+						 1, 1, ctx->base.ctxr_dma,
-+						 &atoken);
-+		if (IS_ERR(first_cdesc)) {
-+			/* No space left in the command descriptor ring */
-+			ret = PTR_ERR(first_cdesc);
-+			goto cdesc_rollback;
-+		}
-+		n_cdesc = 1;
-+		goto skip_cdesc;
-+	}
- 
- 	/* command descriptors */
- 	for_each_sg(src, sg, sreq->nr_src, i) {
- 		int len = sg_dma_len(sg);
- 
- 		/* Do not overflow the request */
--		if (queued - len < 0)
-+		if (queued < len)
- 			len = queued;
- 
- 		cdesc = safexcel_add_cdesc(priv, ring, !n_cdesc,
- 					   !(queued - len),
- 					   sg_dma_address(sg), len, totlen,
--					   ctx->base.ctxr_dma);
-+					   ctx->base.ctxr_dma, &atoken);
- 		if (IS_ERR(cdesc)) {
- 			/* No space left in the command descriptor ring */
- 			ret = PTR_ERR(cdesc);
- 			goto cdesc_rollback;
- 		}
--		n_cdesc++;
- 
--		if (n_cdesc == 1) {
-+		if (!n_cdesc)
- 			first_cdesc = cdesc;
--		}
- 
-+		n_cdesc++;
- 		queued -= len;
- 		if (!queued)
- 			break;
- 	}
--
--	if (unlikely(!n_cdesc)) {
--		/*
--		 * Special case: zero length input buffer.
--		 * The engine always needs the 1st command descriptor, however!
--		 */
--		first_cdesc = safexcel_add_cdesc(priv, ring, 1, 1, 0, 0, totlen,
--						 ctx->base.ctxr_dma);
--		n_cdesc = 1;
--	}
--
-+skip_cdesc:
- 	/* Add context control words and token to first command descriptor */
- 	safexcel_context_control(ctx, base, sreq, first_cdesc);
- 	if (ctx->aead)
--		safexcel_aead_token(ctx, iv, first_cdesc,
-+		safexcel_aead_token(ctx, iv, first_cdesc, atoken,
- 				    sreq->direction, cryptlen,
- 				    assoclen, digestsize);
- 	else
--		safexcel_skcipher_token(ctx, iv, first_cdesc,
-+		safexcel_skcipher_token(ctx, iv, first_cdesc, atoken,
- 					cryptlen);
- 
- 	/* result descriptors */
-@@ -1073,6 +1215,8 @@ static int safexcel_skcipher_cra_init(st
- 
- 	ctx->base.send = safexcel_skcipher_send;
- 	ctx->base.handle_result = safexcel_skcipher_handle_result;
-+	ctx->ivmask = EIP197_OPTION_4_TOKEN_IV_CMD;
-+	ctx->ctrinit = 1;
- 	return 0;
- }
- 
-@@ -1137,6 +1281,8 @@ static int safexcel_skcipher_aes_ecb_cra
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_AES;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_ECB;
-+	ctx->blocksz = 0;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
- 	return 0;
- }
- 
-@@ -1171,6 +1317,7 @@ static int safexcel_skcipher_aes_cbc_cra
- 
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_AES;
-+	ctx->blocksz = AES_BLOCK_SIZE;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CBC;
- 	return 0;
- }
-@@ -1207,6 +1354,7 @@ static int safexcel_skcipher_aes_cfb_cra
- 
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_AES;
-+	ctx->blocksz = AES_BLOCK_SIZE;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CFB;
- 	return 0;
- }
-@@ -1243,6 +1391,7 @@ static int safexcel_skcipher_aes_ofb_cra
- 
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_AES;
-+	ctx->blocksz = AES_BLOCK_SIZE;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_OFB;
- 	return 0;
- }
-@@ -1288,14 +1437,12 @@ static int safexcel_skcipher_aesctr_setk
- 	/* exclude the nonce here */
- 	keylen = len - CTR_RFC3686_NONCE_SIZE;
- 	ret = aes_expandkey(&aes, key, keylen);
--	if (ret) {
--		crypto_skcipher_set_flags(ctfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
-+	if (ret)
- 		return ret;
--	}
- 
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
- 		for (i = 0; i < keylen / sizeof(u32); i++) {
--			if (ctx->key[i] != cpu_to_le32(aes.key_enc[i])) {
-+			if (le32_to_cpu(ctx->key[i]) != aes.key_enc[i]) {
- 				ctx->base.needs_inv = true;
- 				break;
- 			}
-@@ -1317,6 +1464,7 @@ static int safexcel_skcipher_aes_ctr_cra
- 
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_AES;
-+	ctx->blocksz = AES_BLOCK_SIZE;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD;
- 	return 0;
- }
-@@ -1352,6 +1500,7 @@ static int safexcel_des_setkey(struct cr
- 			       unsigned int len)
- {
- 	struct safexcel_cipher_ctx *ctx = crypto_skcipher_ctx(ctfm);
-+	struct safexcel_crypto_priv *priv = ctx->priv;
- 	int ret;
- 
- 	ret = verify_skcipher_des_key(ctfm, key);
-@@ -1359,7 +1508,7 @@ static int safexcel_des_setkey(struct cr
- 		return ret;
- 
- 	/* if context exits and key changed, need to invalidate it */
--	if (ctx->base.ctxr_dma)
-+	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma)
- 		if (memcmp(ctx->key, key, len))
- 			ctx->base.needs_inv = true;
- 
-@@ -1375,6 +1524,8 @@ static int safexcel_skcipher_des_cbc_cra
- 
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_DES;
-+	ctx->blocksz = DES_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CBC;
- 	return 0;
- }
-@@ -1412,6 +1563,8 @@ static int safexcel_skcipher_des_ecb_cra
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_DES;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_ECB;
-+	ctx->blocksz = 0;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
- 	return 0;
- }
- 
-@@ -1444,6 +1597,7 @@ static int safexcel_des3_ede_setkey(stru
- 				   const u8 *key, unsigned int len)
- {
- 	struct safexcel_cipher_ctx *ctx = crypto_skcipher_ctx(ctfm);
-+	struct safexcel_crypto_priv *priv = ctx->priv;
- 	int err;
- 
- 	err = verify_skcipher_des3_key(ctfm, key);
-@@ -1451,13 +1605,11 @@ static int safexcel_des3_ede_setkey(stru
- 		return err;
- 
- 	/* if context exits and key changed, need to invalidate it */
--	if (ctx->base.ctxr_dma) {
-+	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma)
- 		if (memcmp(ctx->key, key, len))
- 			ctx->base.needs_inv = true;
--	}
- 
- 	memcpy(ctx->key, key, len);
--
- 	ctx->key_len = len;
- 
- 	return 0;
-@@ -1469,6 +1621,8 @@ static int safexcel_skcipher_des3_cbc_cr
- 
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_3DES;
-+	ctx->blocksz = DES3_EDE_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CBC;
- 	return 0;
- }
-@@ -1506,6 +1660,8 @@ static int safexcel_skcipher_des3_ecb_cr
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_3DES;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_ECB;
-+	ctx->blocksz = 0;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
- 	return 0;
- }
- 
-@@ -1561,6 +1717,9 @@ static int safexcel_aead_cra_init(struct
- 	ctx->priv = tmpl->priv;
- 
- 	ctx->alg  = SAFEXCEL_AES; /* default */
-+	ctx->blocksz = AES_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_4_TOKEN_IV_CMD;
-+	ctx->ctrinit = 1;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CBC; /* default */
- 	ctx->aead = true;
- 	ctx->base.send = safexcel_aead_send;
-@@ -1749,6 +1908,8 @@ static int safexcel_aead_sha1_des3_cra_i
- 
- 	safexcel_aead_sha1_cra_init(tfm);
- 	ctx->alg = SAFEXCEL_3DES; /* override default */
-+	ctx->blocksz = DES3_EDE_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
- 	return 0;
- }
- 
-@@ -1777,6 +1938,330 @@ struct safexcel_alg_template safexcel_al
- 	},
- };
- 
-+static int safexcel_aead_sha256_des3_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha256_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_3DES; /* override default */
-+	ctx->blocksz = DES3_EDE_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha256_cbc_des3_ede = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_256,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES3_EDE_BLOCK_SIZE,
-+		.maxauthsize = SHA256_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha256),cbc(des3_ede))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha256-cbc-des3_ede",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES3_EDE_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha256_des3_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha224_des3_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha224_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_3DES; /* override default */
-+	ctx->blocksz = DES3_EDE_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha224_cbc_des3_ede = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_256,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES3_EDE_BLOCK_SIZE,
-+		.maxauthsize = SHA224_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha224),cbc(des3_ede))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha224-cbc-des3_ede",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES3_EDE_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha224_des3_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha512_des3_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha512_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_3DES; /* override default */
-+	ctx->blocksz = DES3_EDE_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha512_cbc_des3_ede = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_512,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES3_EDE_BLOCK_SIZE,
-+		.maxauthsize = SHA512_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha512),cbc(des3_ede))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha512-cbc-des3_ede",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES3_EDE_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha512_des3_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha384_des3_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha384_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_3DES; /* override default */
-+	ctx->blocksz = DES3_EDE_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha384_cbc_des3_ede = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_512,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES3_EDE_BLOCK_SIZE,
-+		.maxauthsize = SHA384_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha384),cbc(des3_ede))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha384-cbc-des3_ede",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES3_EDE_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha384_des3_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha1_des_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha1_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_DES; /* override default */
-+	ctx->blocksz = DES_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha1_cbc_des = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA1,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES_BLOCK_SIZE,
-+		.maxauthsize = SHA1_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha1),cbc(des))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha1-cbc-des",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha1_des_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha256_des_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha256_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_DES; /* override default */
-+	ctx->blocksz = DES_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha256_cbc_des = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_256,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES_BLOCK_SIZE,
-+		.maxauthsize = SHA256_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha256),cbc(des))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha256-cbc-des",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha256_des_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha224_des_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha224_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_DES; /* override default */
-+	ctx->blocksz = DES_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha224_cbc_des = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_256,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES_BLOCK_SIZE,
-+		.maxauthsize = SHA224_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha224),cbc(des))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha224-cbc-des",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha224_des_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha512_des_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha512_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_DES; /* override default */
-+	ctx->blocksz = DES_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha512_cbc_des = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_512,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES_BLOCK_SIZE,
-+		.maxauthsize = SHA512_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha512),cbc(des))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha512-cbc-des",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha512_des_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sha384_des_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sha384_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_DES; /* override default */
-+	ctx->blocksz = DES_BLOCK_SIZE;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha384_cbc_des = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_DES | SAFEXCEL_ALG_SHA2_512,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = DES_BLOCK_SIZE,
-+		.maxauthsize = SHA384_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha384),cbc(des))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha384-cbc-des",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = DES_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sha384_des_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
- static int safexcel_aead_sha1_ctr_cra_init(struct crypto_tfm *tfm)
- {
- 	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-@@ -1965,14 +2450,12 @@ static int safexcel_skcipher_aesxts_setk
- 	/* Only half of the key data is cipher key */
- 	keylen = (len >> 1);
- 	ret = aes_expandkey(&aes, key, keylen);
--	if (ret) {
--		crypto_skcipher_set_flags(ctfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
-+	if (ret)
- 		return ret;
--	}
- 
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
- 		for (i = 0; i < keylen / sizeof(u32); i++) {
--			if (ctx->key[i] != cpu_to_le32(aes.key_enc[i])) {
-+			if (le32_to_cpu(ctx->key[i]) != aes.key_enc[i]) {
- 				ctx->base.needs_inv = true;
- 				break;
- 			}
-@@ -1984,15 +2467,13 @@ static int safexcel_skcipher_aesxts_setk
- 
- 	/* The other half is the tweak key */
- 	ret = aes_expandkey(&aes, (u8 *)(key + keylen), keylen);
--	if (ret) {
--		crypto_skcipher_set_flags(ctfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
-+	if (ret)
- 		return ret;
--	}
- 
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
- 		for (i = 0; i < keylen / sizeof(u32); i++) {
--			if (ctx->key[i + keylen / sizeof(u32)] !=
--			    cpu_to_le32(aes.key_enc[i])) {
-+			if (le32_to_cpu(ctx->key[i + keylen / sizeof(u32)]) !=
-+			    aes.key_enc[i]) {
- 				ctx->base.needs_inv = true;
- 				break;
- 			}
-@@ -2015,6 +2496,7 @@ static int safexcel_skcipher_aes_xts_cra
- 
- 	safexcel_skcipher_cra_init(tfm);
- 	ctx->alg  = SAFEXCEL_AES;
-+	ctx->blocksz = AES_BLOCK_SIZE;
- 	ctx->xts  = 1;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_XTS;
- 	return 0;
-@@ -2075,14 +2557,13 @@ static int safexcel_aead_gcm_setkey(stru
- 
- 	ret = aes_expandkey(&aes, key, len);
- 	if (ret) {
--		crypto_aead_set_flags(ctfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
- 		memzero_explicit(&aes, sizeof(aes));
- 		return ret;
- 	}
- 
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
- 		for (i = 0; i < len / sizeof(u32); i++) {
--			if (ctx->key[i] != cpu_to_le32(aes.key_enc[i])) {
-+			if (le32_to_cpu(ctx->key[i]) != aes.key_enc[i]) {
- 				ctx->base.needs_inv = true;
- 				break;
- 			}
-@@ -2099,8 +2580,6 @@ static int safexcel_aead_gcm_setkey(stru
- 	crypto_cipher_set_flags(ctx->hkaes, crypto_aead_get_flags(ctfm) &
- 				CRYPTO_TFM_REQ_MASK);
- 	ret = crypto_cipher_setkey(ctx->hkaes, key, len);
--	crypto_aead_set_flags(ctfm, crypto_cipher_get_flags(ctx->hkaes) &
--			      CRYPTO_TFM_RES_MASK);
- 	if (ret)
- 		return ret;
- 
-@@ -2109,7 +2588,7 @@ static int safexcel_aead_gcm_setkey(stru
- 
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
- 		for (i = 0; i < AES_BLOCK_SIZE / sizeof(u32); i++) {
--			if (ctx->ipad[i] != cpu_to_be32(hashkey[i])) {
-+			if (be32_to_cpu(ctx->ipad[i]) != hashkey[i]) {
- 				ctx->base.needs_inv = true;
- 				break;
- 			}
-@@ -2135,10 +2614,7 @@ static int safexcel_aead_gcm_cra_init(st
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_XCM; /* override default */
- 
- 	ctx->hkaes = crypto_alloc_cipher("aes", 0, 0);
--	if (IS_ERR(ctx->hkaes))
--		return PTR_ERR(ctx->hkaes);
--
--	return 0;
-+	return PTR_ERR_OR_ZERO(ctx->hkaes);
- }
- 
- static void safexcel_aead_gcm_cra_exit(struct crypto_tfm *tfm)
-@@ -2192,14 +2668,13 @@ static int safexcel_aead_ccm_setkey(stru
- 
- 	ret = aes_expandkey(&aes, key, len);
- 	if (ret) {
--		crypto_aead_set_flags(ctfm, CRYPTO_TFM_RES_BAD_KEY_LEN);
- 		memzero_explicit(&aes, sizeof(aes));
- 		return ret;
- 	}
- 
- 	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma) {
- 		for (i = 0; i < len / sizeof(u32); i++) {
--			if (ctx->key[i] != cpu_to_le32(aes.key_enc[i])) {
-+			if (le32_to_cpu(ctx->key[i]) != aes.key_enc[i]) {
- 				ctx->base.needs_inv = true;
- 				break;
- 			}
-@@ -2235,6 +2710,7 @@ static int safexcel_aead_ccm_cra_init(st
- 	ctx->state_sz = 3 * AES_BLOCK_SIZE;
- 	ctx->xcm = EIP197_XCM_MODE_CCM;
- 	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_XCM; /* override default */
-+	ctx->ctrinit = 0;
- 	return 0;
- }
- 
-@@ -2301,5 +2777,949 @@ struct safexcel_alg_template safexcel_al
- 			.cra_exit = safexcel_aead_cra_exit,
- 			.cra_module = THIS_MODULE,
- 		},
-+	},
-+};
-+
-+static void safexcel_chacha20_setkey(struct safexcel_cipher_ctx *ctx,
-+				     const u8 *key)
-+{
-+	struct safexcel_crypto_priv *priv = ctx->priv;
-+
-+	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma)
-+		if (memcmp(ctx->key, key, CHACHA_KEY_SIZE))
-+			ctx->base.needs_inv = true;
-+
-+	memcpy(ctx->key, key, CHACHA_KEY_SIZE);
-+	ctx->key_len = CHACHA_KEY_SIZE;
-+}
-+
-+static int safexcel_skcipher_chacha20_setkey(struct crypto_skcipher *ctfm,
-+					     const u8 *key, unsigned int len)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_skcipher_ctx(ctfm);
-+
-+	if (len != CHACHA_KEY_SIZE)
-+		return -EINVAL;
-+
-+	safexcel_chacha20_setkey(ctx, key);
-+
-+	return 0;
-+}
-+
-+static int safexcel_skcipher_chacha20_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_skcipher_cra_init(tfm);
-+	ctx->alg  = SAFEXCEL_CHACHA20;
-+	ctx->ctrinit = 0;
-+	ctx->mode = CONTEXT_CONTROL_CHACHA20_MODE_256_32;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_chacha20 = {
-+	.type = SAFEXCEL_ALG_TYPE_SKCIPHER,
-+	.algo_mask = SAFEXCEL_ALG_CHACHA20,
-+	.alg.skcipher = {
-+		.setkey = safexcel_skcipher_chacha20_setkey,
-+		.encrypt = safexcel_encrypt,
-+		.decrypt = safexcel_decrypt,
-+		.min_keysize = CHACHA_KEY_SIZE,
-+		.max_keysize = CHACHA_KEY_SIZE,
-+		.ivsize = CHACHA_IV_SIZE,
-+		.base = {
-+			.cra_name = "chacha20",
-+			.cra_driver_name = "safexcel-chacha20",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_skcipher_chacha20_cra_init,
-+			.cra_exit = safexcel_skcipher_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_chachapoly_setkey(struct crypto_aead *ctfm,
-+				    const u8 *key, unsigned int len)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_aead_ctx(ctfm);
-+
-+	if (ctx->aead  == EIP197_AEAD_TYPE_IPSEC_ESP &&
-+	    len > EIP197_AEAD_IPSEC_NONCE_SIZE) {
-+		/* ESP variant has nonce appended to key */
-+		len -= EIP197_AEAD_IPSEC_NONCE_SIZE;
-+		ctx->nonce = *(u32 *)(key + len);
-+	}
-+	if (len != CHACHA_KEY_SIZE)
-+		return -EINVAL;
-+
-+	safexcel_chacha20_setkey(ctx, key);
-+
-+	return 0;
-+}
-+
-+static int safexcel_aead_chachapoly_setauthsize(struct crypto_aead *tfm,
-+					 unsigned int authsize)
-+{
-+	if (authsize != POLY1305_DIGEST_SIZE)
-+		return -EINVAL;
-+	return 0;
-+}
-+
-+static int safexcel_aead_chachapoly_crypt(struct aead_request *req,
-+					  enum safexcel_cipher_direction dir)
-+{
-+	struct safexcel_cipher_req *creq = aead_request_ctx(req);
-+	struct crypto_aead *aead = crypto_aead_reqtfm(req);
-+	struct crypto_tfm *tfm = crypto_aead_tfm(aead);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+	struct aead_request *subreq = aead_request_ctx(req);
-+	u32 key[CHACHA_KEY_SIZE / sizeof(u32) + 1];
-+	int ret = 0;
-+
-+	/*
-+	 * Instead of wasting time detecting umpteen silly corner cases,
-+	 * just dump all "small" requests to the fallback implementation.
-+	 * HW would not be faster on such small requests anyway.
-+	 */
-+	if (likely((ctx->aead != EIP197_AEAD_TYPE_IPSEC_ESP ||
-+		    req->assoclen >= EIP197_AEAD_IPSEC_IV_SIZE) &&
-+		   req->cryptlen > POLY1305_DIGEST_SIZE)) {
-+		return safexcel_queue_req(&req->base, creq, dir);
-+	}
-+
-+	/* HW cannot do full (AAD+payload) zero length, use fallback */
-+	memcpy(key, ctx->key, CHACHA_KEY_SIZE);
-+	if (ctx->aead == EIP197_AEAD_TYPE_IPSEC_ESP) {
-+		/* ESP variant has nonce appended to the key */
-+		key[CHACHA_KEY_SIZE / sizeof(u32)] = ctx->nonce;
-+		ret = crypto_aead_setkey(ctx->fback, (u8 *)key,
-+					 CHACHA_KEY_SIZE +
-+					 EIP197_AEAD_IPSEC_NONCE_SIZE);
-+	} else {
-+		ret = crypto_aead_setkey(ctx->fback, (u8 *)key,
-+					 CHACHA_KEY_SIZE);
-+	}
-+	if (ret) {
-+		crypto_aead_clear_flags(aead, CRYPTO_TFM_REQ_MASK);
-+		crypto_aead_set_flags(aead, crypto_aead_get_flags(ctx->fback) &
-+					    CRYPTO_TFM_REQ_MASK);
-+		return ret;
-+	}
-+
-+	aead_request_set_tfm(subreq, ctx->fback);
-+	aead_request_set_callback(subreq, req->base.flags, req->base.complete,
-+				  req->base.data);
-+	aead_request_set_crypt(subreq, req->src, req->dst, req->cryptlen,
-+			       req->iv);
-+	aead_request_set_ad(subreq, req->assoclen);
-+
-+	return (dir ==  SAFEXCEL_ENCRYPT) ?
-+		crypto_aead_encrypt(subreq) :
-+		crypto_aead_decrypt(subreq);
-+}
-+
-+static int safexcel_aead_chachapoly_encrypt(struct aead_request *req)
-+{
-+	return safexcel_aead_chachapoly_crypt(req, SAFEXCEL_ENCRYPT);
-+}
-+
-+static int safexcel_aead_chachapoly_decrypt(struct aead_request *req)
-+{
-+	return safexcel_aead_chachapoly_crypt(req, SAFEXCEL_DECRYPT);
-+}
-+
-+static int safexcel_aead_fallback_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct crypto_aead *aead = __crypto_aead_cast(tfm);
-+	struct aead_alg *alg = crypto_aead_alg(aead);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_cra_init(tfm);
-+
-+	/* Allocate fallback implementation */
-+	ctx->fback = crypto_alloc_aead(alg->base.cra_name, 0,
-+				       CRYPTO_ALG_ASYNC |
-+				       CRYPTO_ALG_NEED_FALLBACK);
-+	if (IS_ERR(ctx->fback))
-+		return PTR_ERR(ctx->fback);
-+
-+	crypto_aead_set_reqsize(aead, max(sizeof(struct safexcel_cipher_req),
-+					  sizeof(struct aead_request) +
-+					  crypto_aead_reqsize(ctx->fback)));
-+
-+	return 0;
-+}
-+
-+static int safexcel_aead_chachapoly_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_fallback_cra_init(tfm);
-+	ctx->alg  = SAFEXCEL_CHACHA20;
-+	ctx->mode = CONTEXT_CONTROL_CHACHA20_MODE_256_32 |
-+		    CONTEXT_CONTROL_CHACHA20_MODE_CALC_OTK;
-+	ctx->ctrinit = 0;
-+	ctx->hash_alg = CONTEXT_CONTROL_CRYPTO_ALG_POLY1305;
-+	ctx->state_sz = 0; /* Precomputed by HW */
-+	return 0;
-+}
-+
-+static void safexcel_aead_fallback_cra_exit(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	crypto_free_aead(ctx->fback);
-+	safexcel_aead_cra_exit(tfm);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_chachapoly = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_CHACHA20 | SAFEXCEL_ALG_POLY1305,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_chachapoly_setkey,
-+		.setauthsize = safexcel_aead_chachapoly_setauthsize,
-+		.encrypt = safexcel_aead_chachapoly_encrypt,
-+		.decrypt = safexcel_aead_chachapoly_decrypt,
-+		.ivsize = CHACHAPOLY_IV_SIZE,
-+		.maxauthsize = POLY1305_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "rfc7539(chacha20,poly1305)",
-+			.cra_driver_name = "safexcel-chacha20-poly1305",
-+			/* +1 to put it above HW chacha + SW poly */
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY + 1,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+				     CRYPTO_ALG_NEED_FALLBACK,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_chachapoly_cra_init,
-+			.cra_exit = safexcel_aead_fallback_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_chachapolyesp_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+	int ret;
-+
-+	ret = safexcel_aead_chachapoly_cra_init(tfm);
-+	ctx->aead  = EIP197_AEAD_TYPE_IPSEC_ESP;
-+	ctx->aadskip = EIP197_AEAD_IPSEC_IV_SIZE;
-+	return ret;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_chachapoly_esp = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_CHACHA20 | SAFEXCEL_ALG_POLY1305,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_chachapoly_setkey,
-+		.setauthsize = safexcel_aead_chachapoly_setauthsize,
-+		.encrypt = safexcel_aead_chachapoly_encrypt,
-+		.decrypt = safexcel_aead_chachapoly_decrypt,
-+		.ivsize = CHACHAPOLY_IV_SIZE - EIP197_AEAD_IPSEC_NONCE_SIZE,
-+		.maxauthsize = POLY1305_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "rfc7539esp(chacha20,poly1305)",
-+			.cra_driver_name = "safexcel-chacha20-poly1305-esp",
-+			/* +1 to put it above HW chacha + SW poly */
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY + 1,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+				     CRYPTO_ALG_NEED_FALLBACK,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_chachapolyesp_cra_init,
-+			.cra_exit = safexcel_aead_fallback_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_skcipher_sm4_setkey(struct crypto_skcipher *ctfm,
-+					const u8 *key, unsigned int len)
-+{
-+	struct crypto_tfm *tfm = crypto_skcipher_tfm(ctfm);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+	struct safexcel_crypto_priv *priv = ctx->priv;
-+
-+	if (len != SM4_KEY_SIZE)
-+		return -EINVAL;
-+
-+	if (priv->flags & EIP197_TRC_CACHE && ctx->base.ctxr_dma)
-+		if (memcmp(ctx->key, key, SM4_KEY_SIZE))
-+			ctx->base.needs_inv = true;
-+
-+	memcpy(ctx->key, key, SM4_KEY_SIZE);
-+	ctx->key_len = SM4_KEY_SIZE;
-+
-+	return 0;
-+}
-+
-+static int safexcel_sm4_blk_encrypt(struct skcipher_request *req)
-+{
-+	/* Workaround for HW bug: EIP96 4.3 does not report blocksize error */
-+	if (req->cryptlen & (SM4_BLOCK_SIZE - 1))
-+		return -EINVAL;
-+	else
-+		return safexcel_queue_req(&req->base, skcipher_request_ctx(req),
-+					  SAFEXCEL_ENCRYPT);
-+}
-+
-+static int safexcel_sm4_blk_decrypt(struct skcipher_request *req)
-+{
-+	/* Workaround for HW bug: EIP96 4.3 does not report blocksize error */
-+	if (req->cryptlen & (SM4_BLOCK_SIZE - 1))
-+		return -EINVAL;
-+	else
-+		return safexcel_queue_req(&req->base, skcipher_request_ctx(req),
-+					  SAFEXCEL_DECRYPT);
-+}
-+
-+static int safexcel_skcipher_sm4_ecb_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_skcipher_cra_init(tfm);
-+	ctx->alg  = SAFEXCEL_SM4;
-+	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_ECB;
-+	ctx->blocksz = 0;
-+	ctx->ivmask = EIP197_OPTION_2_TOKEN_IV_CMD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_ecb_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_SKCIPHER,
-+	.algo_mask = SAFEXCEL_ALG_SM4,
-+	.alg.skcipher = {
-+		.setkey = safexcel_skcipher_sm4_setkey,
-+		.encrypt = safexcel_sm4_blk_encrypt,
-+		.decrypt = safexcel_sm4_blk_decrypt,
-+		.min_keysize = SM4_KEY_SIZE,
-+		.max_keysize = SM4_KEY_SIZE,
-+		.base = {
-+			.cra_name = "ecb(sm4)",
-+			.cra_driver_name = "safexcel-ecb-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = SM4_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_skcipher_sm4_ecb_cra_init,
-+			.cra_exit = safexcel_skcipher_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_skcipher_sm4_cbc_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_skcipher_cra_init(tfm);
-+	ctx->alg  = SAFEXCEL_SM4;
-+	ctx->blocksz = SM4_BLOCK_SIZE;
-+	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CBC;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_cbc_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_SKCIPHER,
-+	.algo_mask = SAFEXCEL_ALG_SM4,
-+	.alg.skcipher = {
-+		.setkey = safexcel_skcipher_sm4_setkey,
-+		.encrypt = safexcel_sm4_blk_encrypt,
-+		.decrypt = safexcel_sm4_blk_decrypt,
-+		.min_keysize = SM4_KEY_SIZE,
-+		.max_keysize = SM4_KEY_SIZE,
-+		.ivsize = SM4_BLOCK_SIZE,
-+		.base = {
-+			.cra_name = "cbc(sm4)",
-+			.cra_driver_name = "safexcel-cbc-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = SM4_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_skcipher_sm4_cbc_cra_init,
-+			.cra_exit = safexcel_skcipher_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_skcipher_sm4_ofb_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_skcipher_cra_init(tfm);
-+	ctx->alg  = SAFEXCEL_SM4;
-+	ctx->blocksz = SM4_BLOCK_SIZE;
-+	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_OFB;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_ofb_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_SKCIPHER,
-+	.algo_mask = SAFEXCEL_ALG_SM4 | SAFEXCEL_ALG_AES_XFB,
-+	.alg.skcipher = {
-+		.setkey = safexcel_skcipher_sm4_setkey,
-+		.encrypt = safexcel_encrypt,
-+		.decrypt = safexcel_decrypt,
-+		.min_keysize = SM4_KEY_SIZE,
-+		.max_keysize = SM4_KEY_SIZE,
-+		.ivsize = SM4_BLOCK_SIZE,
-+		.base = {
-+			.cra_name = "ofb(sm4)",
-+			.cra_driver_name = "safexcel-ofb-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_skcipher_sm4_ofb_cra_init,
-+			.cra_exit = safexcel_skcipher_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_skcipher_sm4_cfb_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_skcipher_cra_init(tfm);
-+	ctx->alg  = SAFEXCEL_SM4;
-+	ctx->blocksz = SM4_BLOCK_SIZE;
-+	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CFB;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_cfb_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_SKCIPHER,
-+	.algo_mask = SAFEXCEL_ALG_SM4 | SAFEXCEL_ALG_AES_XFB,
-+	.alg.skcipher = {
-+		.setkey = safexcel_skcipher_sm4_setkey,
-+		.encrypt = safexcel_encrypt,
-+		.decrypt = safexcel_decrypt,
-+		.min_keysize = SM4_KEY_SIZE,
-+		.max_keysize = SM4_KEY_SIZE,
-+		.ivsize = SM4_BLOCK_SIZE,
-+		.base = {
-+			.cra_name = "cfb(sm4)",
-+			.cra_driver_name = "safexcel-cfb-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_skcipher_sm4_cfb_cra_init,
-+			.cra_exit = safexcel_skcipher_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_skcipher_sm4ctr_setkey(struct crypto_skcipher *ctfm,
-+					   const u8 *key, unsigned int len)
-+{
-+	struct crypto_tfm *tfm = crypto_skcipher_tfm(ctfm);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	/* last 4 bytes of key are the nonce! */
-+	ctx->nonce = *(u32 *)(key + len - CTR_RFC3686_NONCE_SIZE);
-+	/* exclude the nonce here */
-+	len -= CTR_RFC3686_NONCE_SIZE;
-+
-+	return safexcel_skcipher_sm4_setkey(ctfm, key, len);
-+}
-+
-+static int safexcel_skcipher_sm4_ctr_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_skcipher_cra_init(tfm);
-+	ctx->alg  = SAFEXCEL_SM4;
-+	ctx->blocksz = SM4_BLOCK_SIZE;
-+	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_ctr_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_SKCIPHER,
-+	.algo_mask = SAFEXCEL_ALG_SM4,
-+	.alg.skcipher = {
-+		.setkey = safexcel_skcipher_sm4ctr_setkey,
-+		.encrypt = safexcel_encrypt,
-+		.decrypt = safexcel_decrypt,
-+		/* Add nonce size */
-+		.min_keysize = SM4_KEY_SIZE + CTR_RFC3686_NONCE_SIZE,
-+		.max_keysize = SM4_KEY_SIZE + CTR_RFC3686_NONCE_SIZE,
-+		.ivsize = CTR_RFC3686_IV_SIZE,
-+		.base = {
-+			.cra_name = "rfc3686(ctr(sm4))",
-+			.cra_driver_name = "safexcel-ctr-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_skcipher_sm4_ctr_cra_init,
-+			.cra_exit = safexcel_skcipher_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sm4_blk_encrypt(struct aead_request *req)
-+{
-+	/* Workaround for HW bug: EIP96 4.3 does not report blocksize error */
-+	if (req->cryptlen & (SM4_BLOCK_SIZE - 1))
-+		return -EINVAL;
-+
-+	return safexcel_queue_req(&req->base, aead_request_ctx(req),
-+				  SAFEXCEL_ENCRYPT);
-+}
-+
-+static int safexcel_aead_sm4_blk_decrypt(struct aead_request *req)
-+{
-+	struct crypto_aead *tfm = crypto_aead_reqtfm(req);
-+
-+	/* Workaround for HW bug: EIP96 4.3 does not report blocksize error */
-+	if ((req->cryptlen - crypto_aead_authsize(tfm)) & (SM4_BLOCK_SIZE - 1))
-+		return -EINVAL;
-+
-+	return safexcel_queue_req(&req->base, aead_request_ctx(req),
-+				  SAFEXCEL_DECRYPT);
-+}
-+
-+static int safexcel_aead_sm4cbc_sha1_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_SM4;
-+	ctx->blocksz = SM4_BLOCK_SIZE;
-+	ctx->hash_alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA1;
-+	ctx->state_sz = SHA1_DIGEST_SIZE;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha1_cbc_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_SM4 | SAFEXCEL_ALG_SHA1,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_sm4_blk_encrypt,
-+		.decrypt = safexcel_aead_sm4_blk_decrypt,
-+		.ivsize = SM4_BLOCK_SIZE,
-+		.maxauthsize = SHA1_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha1),cbc(sm4))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha1-cbc-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = SM4_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sm4cbc_sha1_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_fallback_setkey(struct crypto_aead *ctfm,
-+					 const u8 *key, unsigned int len)
-+{
-+	struct crypto_tfm *tfm = crypto_aead_tfm(ctfm);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	/* Keep fallback cipher synchronized */
-+	return crypto_aead_setkey(ctx->fback, (u8 *)key, len) ?:
-+	       safexcel_aead_setkey(ctfm, key, len);
-+}
-+
-+static int safexcel_aead_fallback_setauthsize(struct crypto_aead *ctfm,
-+					      unsigned int authsize)
-+{
-+	struct crypto_tfm *tfm = crypto_aead_tfm(ctfm);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	/* Keep fallback cipher synchronized */
-+	return crypto_aead_setauthsize(ctx->fback, authsize);
-+}
-+
-+static int safexcel_aead_fallback_crypt(struct aead_request *req,
-+					enum safexcel_cipher_direction dir)
-+{
-+	struct crypto_aead *aead = crypto_aead_reqtfm(req);
-+	struct crypto_tfm *tfm = crypto_aead_tfm(aead);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+	struct aead_request *subreq = aead_request_ctx(req);
-+
-+	aead_request_set_tfm(subreq, ctx->fback);
-+	aead_request_set_callback(subreq, req->base.flags, req->base.complete,
-+				  req->base.data);
-+	aead_request_set_crypt(subreq, req->src, req->dst, req->cryptlen,
-+			       req->iv);
-+	aead_request_set_ad(subreq, req->assoclen);
-+
-+	return (dir ==  SAFEXCEL_ENCRYPT) ?
-+		crypto_aead_encrypt(subreq) :
-+		crypto_aead_decrypt(subreq);
-+}
-+
-+static int safexcel_aead_sm4cbc_sm3_encrypt(struct aead_request *req)
-+{
-+	struct safexcel_cipher_req *creq = aead_request_ctx(req);
-+
-+	/* Workaround for HW bug: EIP96 4.3 does not report blocksize error */
-+	if (req->cryptlen & (SM4_BLOCK_SIZE - 1))
-+		return -EINVAL;
-+	else if (req->cryptlen || req->assoclen) /* If input length > 0 only */
-+		return safexcel_queue_req(&req->base, creq, SAFEXCEL_ENCRYPT);
-+
-+	/* HW cannot do full (AAD+payload) zero length, use fallback */
-+	return safexcel_aead_fallback_crypt(req, SAFEXCEL_ENCRYPT);
-+}
-+
-+static int safexcel_aead_sm4cbc_sm3_decrypt(struct aead_request *req)
-+{
-+	struct safexcel_cipher_req *creq = aead_request_ctx(req);
-+	struct crypto_aead *tfm = crypto_aead_reqtfm(req);
-+
-+	/* Workaround for HW bug: EIP96 4.3 does not report blocksize error */
-+	if ((req->cryptlen - crypto_aead_authsize(tfm)) & (SM4_BLOCK_SIZE - 1))
-+		return -EINVAL;
-+	else if (req->cryptlen > crypto_aead_authsize(tfm) || req->assoclen)
-+		/* If input length > 0 only */
-+		return safexcel_queue_req(&req->base, creq, SAFEXCEL_DECRYPT);
-+
-+	/* HW cannot do full (AAD+payload) zero length, use fallback */
-+	return safexcel_aead_fallback_crypt(req, SAFEXCEL_DECRYPT);
-+}
-+
-+static int safexcel_aead_sm4cbc_sm3_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_fallback_cra_init(tfm);
-+	ctx->alg = SAFEXCEL_SM4;
-+	ctx->blocksz = SM4_BLOCK_SIZE;
-+	ctx->hash_alg = CONTEXT_CONTROL_CRYPTO_ALG_SM3;
-+	ctx->state_sz = SM3_DIGEST_SIZE;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sm3_cbc_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_SM4 | SAFEXCEL_ALG_SM3,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_fallback_setkey,
-+		.setauthsize = safexcel_aead_fallback_setauthsize,
-+		.encrypt = safexcel_aead_sm4cbc_sm3_encrypt,
-+		.decrypt = safexcel_aead_sm4cbc_sm3_decrypt,
-+		.ivsize = SM4_BLOCK_SIZE,
-+		.maxauthsize = SM3_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sm3),cbc(sm4))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sm3-cbc-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+				     CRYPTO_ALG_NEED_FALLBACK,
-+			.cra_blocksize = SM4_BLOCK_SIZE,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sm4cbc_sm3_cra_init,
-+			.cra_exit = safexcel_aead_fallback_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sm4ctr_sha1_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sm4cbc_sha1_cra_init(tfm);
-+	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sha1_ctr_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_SM4 | SAFEXCEL_ALG_SHA1,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = CTR_RFC3686_IV_SIZE,
-+		.maxauthsize = SHA1_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sha1),rfc3686(ctr(sm4)))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sha1-ctr-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sm4ctr_sha1_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_aead_sm4ctr_sm3_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_aead_sm4cbc_sm3_cra_init(tfm);
-+	ctx->mode = CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD;
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_authenc_hmac_sm3_ctr_sm4 = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_SM4 | SAFEXCEL_ALG_SM3,
-+	.alg.aead = {
-+		.setkey = safexcel_aead_setkey,
-+		.encrypt = safexcel_aead_encrypt,
-+		.decrypt = safexcel_aead_decrypt,
-+		.ivsize = CTR_RFC3686_IV_SIZE,
-+		.maxauthsize = SM3_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "authenc(hmac(sm3),rfc3686(ctr(sm4)))",
-+			.cra_driver_name = "safexcel-authenc-hmac-sm3-ctr-sm4",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_aead_sm4ctr_sm3_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
-+	},
-+};
-+
-+static int safexcel_rfc4106_gcm_setkey(struct crypto_aead *ctfm, const u8 *key,
-+				       unsigned int len)
-+{
-+	struct crypto_tfm *tfm = crypto_aead_tfm(ctfm);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	/* last 4 bytes of key are the nonce! */
-+	ctx->nonce = *(u32 *)(key + len - CTR_RFC3686_NONCE_SIZE);
-+
-+	len -= CTR_RFC3686_NONCE_SIZE;
-+	return safexcel_aead_gcm_setkey(ctfm, key, len);
-+}
-+
-+static int safexcel_rfc4106_gcm_setauthsize(struct crypto_aead *tfm,
-+					    unsigned int authsize)
-+{
-+	return crypto_rfc4106_check_authsize(authsize);
-+}
-+
-+static int safexcel_rfc4106_encrypt(struct aead_request *req)
-+{
-+	return crypto_ipsec_check_assoclen(req->assoclen) ?:
-+	       safexcel_aead_encrypt(req);
-+}
-+
-+static int safexcel_rfc4106_decrypt(struct aead_request *req)
-+{
-+	return crypto_ipsec_check_assoclen(req->assoclen) ?:
-+	       safexcel_aead_decrypt(req);
-+}
-+
-+static int safexcel_rfc4106_gcm_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+	int ret;
-+
-+	ret = safexcel_aead_gcm_cra_init(tfm);
-+	ctx->aead  = EIP197_AEAD_TYPE_IPSEC_ESP;
-+	ctx->aadskip = EIP197_AEAD_IPSEC_IV_SIZE;
-+	return ret;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_rfc4106_gcm = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_AES | SAFEXCEL_ALG_GHASH,
-+	.alg.aead = {
-+		.setkey = safexcel_rfc4106_gcm_setkey,
-+		.setauthsize = safexcel_rfc4106_gcm_setauthsize,
-+		.encrypt = safexcel_rfc4106_encrypt,
-+		.decrypt = safexcel_rfc4106_decrypt,
-+		.ivsize = GCM_RFC4106_IV_SIZE,
-+		.maxauthsize = GHASH_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "rfc4106(gcm(aes))",
-+			.cra_driver_name = "safexcel-rfc4106-gcm-aes",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_rfc4106_gcm_cra_init,
-+			.cra_exit = safexcel_aead_gcm_cra_exit,
-+		},
-+	},
-+};
-+
-+static int safexcel_rfc4543_gcm_setauthsize(struct crypto_aead *tfm,
-+					    unsigned int authsize)
-+{
-+	if (authsize != GHASH_DIGEST_SIZE)
-+		return -EINVAL;
-+
-+	return 0;
-+}
-+
-+static int safexcel_rfc4543_gcm_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+	int ret;
-+
-+	ret = safexcel_aead_gcm_cra_init(tfm);
-+	ctx->aead  = EIP197_AEAD_TYPE_IPSEC_ESP_GMAC;
-+	return ret;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_rfc4543_gcm = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_AES | SAFEXCEL_ALG_GHASH,
-+	.alg.aead = {
-+		.setkey = safexcel_rfc4106_gcm_setkey,
-+		.setauthsize = safexcel_rfc4543_gcm_setauthsize,
-+		.encrypt = safexcel_rfc4106_encrypt,
-+		.decrypt = safexcel_rfc4106_decrypt,
-+		.ivsize = GCM_RFC4543_IV_SIZE,
-+		.maxauthsize = GHASH_DIGEST_SIZE,
-+		.base = {
-+			.cra_name = "rfc4543(gcm(aes))",
-+			.cra_driver_name = "safexcel-rfc4543-gcm-aes",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_rfc4543_gcm_cra_init,
-+			.cra_exit = safexcel_aead_gcm_cra_exit,
-+		},
-+	},
-+};
-+
-+static int safexcel_rfc4309_ccm_setkey(struct crypto_aead *ctfm, const u8 *key,
-+				       unsigned int len)
-+{
-+	struct crypto_tfm *tfm = crypto_aead_tfm(ctfm);
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	/* First byte of the nonce = L = always 3 for RFC4309 (4 byte ctr) */
-+	*(u8 *)&ctx->nonce = EIP197_AEAD_IPSEC_COUNTER_SIZE - 1;
-+	/* last 3 bytes of key are the nonce! */
-+	memcpy((u8 *)&ctx->nonce + 1, key + len -
-+	       EIP197_AEAD_IPSEC_CCM_NONCE_SIZE,
-+	       EIP197_AEAD_IPSEC_CCM_NONCE_SIZE);
-+
-+	len -= EIP197_AEAD_IPSEC_CCM_NONCE_SIZE;
-+	return safexcel_aead_ccm_setkey(ctfm, key, len);
-+}
-+
-+static int safexcel_rfc4309_ccm_setauthsize(struct crypto_aead *tfm,
-+					    unsigned int authsize)
-+{
-+	/* Borrowed from crypto/ccm.c */
-+	switch (authsize) {
-+	case 8:
-+	case 12:
-+	case 16:
-+		break;
-+	default:
-+		return -EINVAL;
-+	}
-+
-+	return 0;
-+}
-+
-+static int safexcel_rfc4309_ccm_encrypt(struct aead_request *req)
-+{
-+	struct safexcel_cipher_req *creq = aead_request_ctx(req);
-+
-+	/* Borrowed from crypto/ccm.c */
-+	if (req->assoclen != 16 && req->assoclen != 20)
-+		return -EINVAL;
-+
-+	return safexcel_queue_req(&req->base, creq, SAFEXCEL_ENCRYPT);
-+}
-+
-+static int safexcel_rfc4309_ccm_decrypt(struct aead_request *req)
-+{
-+	struct safexcel_cipher_req *creq = aead_request_ctx(req);
-+
-+	/* Borrowed from crypto/ccm.c */
-+	if (req->assoclen != 16 && req->assoclen != 20)
-+		return -EINVAL;
-+
-+	return safexcel_queue_req(&req->base, creq, SAFEXCEL_DECRYPT);
-+}
-+
-+static int safexcel_rfc4309_ccm_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
-+	int ret;
-+
-+	ret = safexcel_aead_ccm_cra_init(tfm);
-+	ctx->aead  = EIP197_AEAD_TYPE_IPSEC_ESP;
-+	ctx->aadskip = EIP197_AEAD_IPSEC_IV_SIZE;
-+	return ret;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_rfc4309_ccm = {
-+	.type = SAFEXCEL_ALG_TYPE_AEAD,
-+	.algo_mask = SAFEXCEL_ALG_AES | SAFEXCEL_ALG_CBC_MAC_ALL,
-+	.alg.aead = {
-+		.setkey = safexcel_rfc4309_ccm_setkey,
-+		.setauthsize = safexcel_rfc4309_ccm_setauthsize,
-+		.encrypt = safexcel_rfc4309_ccm_encrypt,
-+		.decrypt = safexcel_rfc4309_ccm_decrypt,
-+		.ivsize = EIP197_AEAD_IPSEC_IV_SIZE,
-+		.maxauthsize = AES_BLOCK_SIZE,
-+		.base = {
-+			.cra_name = "rfc4309(ccm(aes))",
-+			.cra_driver_name = "safexcel-rfc4309-ccm-aes",
-+			.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+			.cra_flags = CRYPTO_ALG_ASYNC |
-+				     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+			.cra_blocksize = 1,
-+			.cra_ctxsize = sizeof(struct safexcel_cipher_ctx),
-+			.cra_alignmask = 0,
-+			.cra_init = safexcel_rfc4309_ccm_cra_init,
-+			.cra_exit = safexcel_aead_cra_exit,
-+			.cra_module = THIS_MODULE,
-+		},
- 	},
- };
---- a/drivers/crypto/inside-secure/safexcel.h
-+++ b/drivers/crypto/inside-secure/safexcel.h
-@@ -17,8 +17,11 @@
- #define EIP197_HIA_VERSION_BE			0xca35
- #define EIP197_HIA_VERSION_LE			0x35ca
- #define EIP97_VERSION_LE			0x9e61
-+#define EIP196_VERSION_LE			0x3bc4
- #define EIP197_VERSION_LE			0x3ac5
- #define EIP96_VERSION_LE			0x9f60
-+#define EIP201_VERSION_LE			0x36c9
-+#define EIP206_VERSION_LE			0x31ce
- #define EIP197_REG_LO16(reg)			(reg & 0xffff)
- #define EIP197_REG_HI16(reg)			((reg >> 16) & 0xffff)
- #define EIP197_VERSION_MASK(reg)		((reg >> 16) & 0xfff)
-@@ -26,12 +29,23 @@
- 						((reg >> 4) & 0xf0) | \
- 						((reg >> 12) & 0xf))
- 
-+/* EIP197 HIA OPTIONS ENCODING */
-+#define EIP197_HIA_OPT_HAS_PE_ARB		BIT(29)
-+
-+/* EIP206 OPTIONS ENCODING */
-+#define EIP206_OPT_ICE_TYPE(n)			((n>>8)&3)
-+
-+/* EIP197 OPTIONS ENCODING */
-+#define EIP197_OPT_HAS_TRC			BIT(31)
-+
- /* Static configuration */
- #define EIP197_DEFAULT_RING_SIZE		400
--#define EIP197_MAX_TOKENS			18
-+#define EIP197_EMB_TOKENS			4 /* Pad CD to 16 dwords */
-+#define EIP197_MAX_TOKENS			16
- #define EIP197_MAX_RINGS			4
- #define EIP197_FETCH_DEPTH			2
- #define EIP197_MAX_BATCH_SZ			64
-+#define EIP197_MAX_RING_AIC			14
- 
- #define EIP197_GFP_FLAGS(base)	((base).flags & CRYPTO_TFM_REQ_MAY_SLEEP ? \
- 				 GFP_KERNEL : GFP_ATOMIC)
-@@ -138,6 +152,7 @@
- #define EIP197_HIA_AIC_R_ENABLED_STAT(r)	(0xe010 - EIP197_HIA_AIC_R_OFF(r))
- #define EIP197_HIA_AIC_R_ACK(r)			(0xe010 - EIP197_HIA_AIC_R_OFF(r))
- #define EIP197_HIA_AIC_R_ENABLE_CLR(r)		(0xe014 - EIP197_HIA_AIC_R_OFF(r))
-+#define EIP197_HIA_AIC_R_VERSION(r)		(0xe01c - EIP197_HIA_AIC_R_OFF(r))
- #define EIP197_HIA_AIC_G_ENABLE_CTRL		0xf808
- #define EIP197_HIA_AIC_G_ENABLED_STAT		0xf810
- #define EIP197_HIA_AIC_G_ACK			0xf810
-@@ -157,12 +172,16 @@
- #define EIP197_PE_EIP96_FUNCTION_EN(n)		(0x1004 + (0x2000 * (n)))
- #define EIP197_PE_EIP96_CONTEXT_CTRL(n)		(0x1008 + (0x2000 * (n)))
- #define EIP197_PE_EIP96_CONTEXT_STAT(n)		(0x100c + (0x2000 * (n)))
-+#define EIP197_PE_EIP96_TOKEN_CTRL2(n)		(0x102c + (0x2000 * (n)))
- #define EIP197_PE_EIP96_FUNCTION2_EN(n)		(0x1030 + (0x2000 * (n)))
- #define EIP197_PE_EIP96_OPTIONS(n)		(0x13f8 + (0x2000 * (n)))
- #define EIP197_PE_EIP96_VERSION(n)		(0x13fc + (0x2000 * (n)))
- #define EIP197_PE_OUT_DBUF_THRES(n)		(0x1c00 + (0x2000 * (n)))
- #define EIP197_PE_OUT_TBUF_THRES(n)		(0x1d00 + (0x2000 * (n)))
-+#define EIP197_PE_OPTIONS(n)			(0x1ff8 + (0x2000 * (n)))
-+#define EIP197_PE_VERSION(n)			(0x1ffc + (0x2000 * (n)))
- #define EIP197_MST_CTRL				0xfff4
-+#define EIP197_OPTIONS				0xfff8
- #define EIP197_VERSION				0xfffc
- 
- /* EIP197-specific registers, no indirection */
-@@ -178,6 +197,7 @@
- #define EIP197_TRC_ECCADMINSTAT			0xf0838
- #define EIP197_TRC_ECCDATASTAT			0xf083c
- #define EIP197_TRC_ECCDATA			0xf0840
-+#define EIP197_STRC_CONFIG			0xf43f0
- #define EIP197_FLUE_CACHEBASE_LO(n)		(0xf6000 + (32 * (n)))
- #define EIP197_FLUE_CACHEBASE_HI(n)		(0xf6004 + (32 * (n)))
- #define EIP197_FLUE_CONFIG(n)			(0xf6010 + (32 * (n)))
-@@ -188,6 +208,7 @@
- 
- /* EIP197_HIA_xDR_DESC_SIZE */
- #define EIP197_xDR_DESC_MODE_64BIT		BIT(31)
-+#define EIP197_CDR_DESC_MODE_ADCP		BIT(30)
- 
- /* EIP197_HIA_xDR_DMA_CFG */
- #define EIP197_HIA_xDR_WR_RES_BUF		BIT(22)
-@@ -213,7 +234,6 @@
- /* EIP197_HIA_xDR_PROC_COUNT */
- #define EIP197_xDR_PROC_xD_PKT_OFFSET		24
- #define EIP197_xDR_PROC_xD_PKT_MASK		GENMASK(6, 0)
--#define EIP197_xDR_PROC_xD_COUNT(n)		((n) << 2)
- #define EIP197_xDR_PROC_xD_PKT(n)		((n) << 24)
- #define EIP197_xDR_PROC_CLR_COUNT		BIT(31)
- 
-@@ -228,6 +248,8 @@
- #define EIP197_HIA_RA_PE_CTRL_EN		BIT(30)
- 
- /* EIP197_HIA_OPTIONS */
-+#define EIP197_N_RINGS_OFFSET			0
-+#define EIP197_N_RINGS_MASK			GENMASK(3, 0)
- #define EIP197_N_PES_OFFSET			4
- #define EIP197_N_PES_MASK			GENMASK(4, 0)
- #define EIP97_N_PES_MASK			GENMASK(2, 0)
-@@ -237,13 +259,13 @@
- #define EIP197_CFSIZE_OFFSET			9
- #define EIP197_CFSIZE_ADJUST			4
- #define EIP97_CFSIZE_OFFSET			8
--#define EIP197_CFSIZE_MASK			GENMASK(3, 0)
--#define EIP97_CFSIZE_MASK			GENMASK(4, 0)
-+#define EIP197_CFSIZE_MASK			GENMASK(2, 0)
-+#define EIP97_CFSIZE_MASK			GENMASK(3, 0)
- #define EIP197_RFSIZE_OFFSET			12
- #define EIP197_RFSIZE_ADJUST			4
- #define EIP97_RFSIZE_OFFSET			12
--#define EIP197_RFSIZE_MASK			GENMASK(3, 0)
--#define EIP97_RFSIZE_MASK			GENMASK(4, 0)
-+#define EIP197_RFSIZE_MASK			GENMASK(2, 0)
-+#define EIP97_RFSIZE_MASK			GENMASK(3, 0)
- 
- /* EIP197_HIA_AIC_R_ENABLE_CTRL */
- #define EIP197_CDR_IRQ(n)			BIT((n) * 2)
-@@ -257,9 +279,9 @@
- #define EIP197_HIA_DxE_CFG_MIN_CTRL_SIZE(n)	((n) << 16)
- #define EIP197_HIA_DxE_CFG_CTRL_CACHE_CTRL(n)	(((n) & 0x7) << 20)
- #define EIP197_HIA_DxE_CFG_MAX_CTRL_SIZE(n)	((n) << 24)
--#define EIP197_HIA_DFE_CFG_DIS_DEBUG		(BIT(31) | BIT(29))
-+#define EIP197_HIA_DFE_CFG_DIS_DEBUG		GENMASK(31, 29)
- #define EIP197_HIA_DSE_CFG_EN_SINGLE_WR		BIT(29)
--#define EIP197_HIA_DSE_CFG_DIS_DEBUG		BIT(31)
-+#define EIP197_HIA_DSE_CFG_DIS_DEBUG		GENMASK(31, 30)
- 
- /* EIP197_HIA_DFE/DSE_THR_CTRL */
- #define EIP197_DxE_THR_CTRL_EN			BIT(30)
-@@ -327,13 +349,21 @@
- #define EIP197_ADDRESS_MODE			BIT(8)
- #define EIP197_CONTROL_MODE			BIT(9)
- 
-+/* EIP197_PE_EIP96_TOKEN_CTRL2 */
-+#define EIP197_PE_EIP96_TOKEN_CTRL2_CTX_DONE	BIT(3)
-+
-+/* EIP197_STRC_CONFIG */
-+#define EIP197_STRC_CONFIG_INIT			BIT(31)
-+#define EIP197_STRC_CONFIG_LARGE_REC(s)		(s<<8)
-+#define EIP197_STRC_CONFIG_SMALL_REC(s)		(s<<0)
-+
- /* EIP197_FLUE_CONFIG */
- #define EIP197_FLUE_CONFIG_MAGIC		0xc7000004
- 
- /* Context Control */
- struct safexcel_context_record {
--	u32 control0;
--	u32 control1;
-+	__le32 control0;
-+	__le32 control1;
- 
- 	__le32 data[40];
- } __packed;
-@@ -358,10 +388,14 @@ struct safexcel_context_record {
- #define CONTEXT_CONTROL_CRYPTO_ALG_AES128	(0x5 << 17)
- #define CONTEXT_CONTROL_CRYPTO_ALG_AES192	(0x6 << 17)
- #define CONTEXT_CONTROL_CRYPTO_ALG_AES256	(0x7 << 17)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_CHACHA20	(0x8 << 17)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_SM4		(0xd << 17)
-+#define CONTEXT_CONTROL_DIGEST_INITIAL		(0x0 << 21)
- #define CONTEXT_CONTROL_DIGEST_PRECOMPUTED	(0x1 << 21)
- #define CONTEXT_CONTROL_DIGEST_XCM		(0x2 << 21)
- #define CONTEXT_CONTROL_DIGEST_HMAC		(0x3 << 21)
- #define CONTEXT_CONTROL_CRYPTO_ALG_MD5		(0x0 << 23)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_CRC32	(0x0 << 23)
- #define CONTEXT_CONTROL_CRYPTO_ALG_SHA1		(0x2 << 23)
- #define CONTEXT_CONTROL_CRYPTO_ALG_SHA224	(0x4 << 23)
- #define CONTEXT_CONTROL_CRYPTO_ALG_SHA256	(0x3 << 23)
-@@ -371,17 +405,25 @@ struct safexcel_context_record {
- #define CONTEXT_CONTROL_CRYPTO_ALG_XCBC128	(0x1 << 23)
- #define CONTEXT_CONTROL_CRYPTO_ALG_XCBC192	(0x2 << 23)
- #define CONTEXT_CONTROL_CRYPTO_ALG_XCBC256	(0x3 << 23)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_SM3		(0x7 << 23)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_SHA3_256	(0xb << 23)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_SHA3_224	(0xc << 23)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_SHA3_512	(0xd << 23)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_SHA3_384	(0xe << 23)
-+#define CONTEXT_CONTROL_CRYPTO_ALG_POLY1305	(0xf << 23)
- #define CONTEXT_CONTROL_INV_FR			(0x5 << 24)
- #define CONTEXT_CONTROL_INV_TR			(0x6 << 24)
- 
- /* control1 */
- #define CONTEXT_CONTROL_CRYPTO_MODE_ECB		(0 << 0)
- #define CONTEXT_CONTROL_CRYPTO_MODE_CBC		(1 << 0)
-+#define CONTEXT_CONTROL_CHACHA20_MODE_256_32	(2 << 0)
- #define CONTEXT_CONTROL_CRYPTO_MODE_OFB		(4 << 0)
- #define CONTEXT_CONTROL_CRYPTO_MODE_CFB		(5 << 0)
- #define CONTEXT_CONTROL_CRYPTO_MODE_CTR_LOAD	(6 << 0)
- #define CONTEXT_CONTROL_CRYPTO_MODE_XTS		(7 << 0)
- #define CONTEXT_CONTROL_CRYPTO_MODE_XCM		((6 << 0) | BIT(17))
-+#define CONTEXT_CONTROL_CHACHA20_MODE_CALC_OTK	(12 << 0)
- #define CONTEXT_CONTROL_IV0			BIT(5)
- #define CONTEXT_CONTROL_IV1			BIT(6)
- #define CONTEXT_CONTROL_IV2			BIT(7)
-@@ -394,6 +436,13 @@ struct safexcel_context_record {
- #define EIP197_XCM_MODE_GCM			1
- #define EIP197_XCM_MODE_CCM			2
- 
-+#define EIP197_AEAD_TYPE_IPSEC_ESP		2
-+#define EIP197_AEAD_TYPE_IPSEC_ESP_GMAC		3
-+#define EIP197_AEAD_IPSEC_IV_SIZE		8
-+#define EIP197_AEAD_IPSEC_NONCE_SIZE		4
-+#define EIP197_AEAD_IPSEC_COUNTER_SIZE		4
-+#define EIP197_AEAD_IPSEC_CCM_NONCE_SIZE	3
-+
- /* The hash counter given to the engine in the context has a granularity of
-  * 64 bits.
-  */
-@@ -423,6 +472,8 @@ struct safexcel_context_record {
- #define EIP197_TRC_PARAMS2_RC_SZ_SMALL(n)	((n) << 18)
- 
- /* Cache helpers */
-+#define EIP197_MIN_DSIZE			1024
-+#define EIP197_MIN_ASIZE			8
- #define EIP197_CS_TRC_REC_WC			64
- #define EIP197_CS_RC_SIZE			(4 * sizeof(u32))
- #define EIP197_CS_RC_NEXT(x)			(x)
-@@ -447,7 +498,7 @@ struct result_data_desc {
- 	u16 application_id;
- 	u16 rsvd1;
- 
--	u32 rsvd2;
-+	u32 rsvd2[5];
- } __packed;
- 
- 
-@@ -465,16 +516,15 @@ struct safexcel_result_desc {
- 
- 	u32 data_lo;
- 	u32 data_hi;
--
--	struct result_data_desc result_data;
- } __packed;
- 
- /*
-  * The EIP(1)97 only needs to fetch the descriptor part of
-  * the result descriptor, not the result token part!
-  */
--#define EIP197_RD64_FETCH_SIZE		((sizeof(struct safexcel_result_desc) -\
--					  sizeof(struct result_data_desc)) /\
-+#define EIP197_RD64_FETCH_SIZE		(sizeof(struct safexcel_result_desc) /\
-+					 sizeof(u32))
-+#define EIP197_RD64_RESULT_SIZE		(sizeof(struct result_data_desc) /\
- 					 sizeof(u32))
- 
- struct safexcel_token {
-@@ -505,6 +555,8 @@ static inline void eip197_noop_token(str
- {
- 	token->opcode = EIP197_TOKEN_OPCODE_NOOP;
- 	token->packet_length = BIT(2);
-+	token->stat = 0;
-+	token->instructions = 0;
- }
- 
- /* Instructions */
-@@ -526,14 +578,13 @@ struct safexcel_control_data_desc {
- 	u16 application_id;
- 	u16 rsvd;
- 
--	u8 refresh:2;
--	u32 context_lo:30;
-+	u32 context_lo;
- 	u32 context_hi;
- 
- 	u32 control0;
- 	u32 control1;
- 
--	u32 token[EIP197_MAX_TOKENS];
-+	u32 token[EIP197_EMB_TOKENS];
- } __packed;
- 
- #define EIP197_OPTION_MAGIC_VALUE	BIT(0)
-@@ -543,7 +594,10 @@ struct safexcel_control_data_desc {
- #define EIP197_OPTION_2_TOKEN_IV_CMD	GENMASK(11, 10)
- #define EIP197_OPTION_4_TOKEN_IV_CMD	GENMASK(11, 9)
- 
-+#define EIP197_TYPE_BCLA		0x0
- #define EIP197_TYPE_EXTENDED		0x3
-+#define EIP197_CONTEXT_SMALL		0x2
-+#define EIP197_CONTEXT_SIZE_MASK	0x3
- 
- /* Basic Command Descriptor format */
- struct safexcel_command_desc {
-@@ -551,16 +605,22 @@ struct safexcel_command_desc {
- 	u8 rsvd0:5;
- 	u8 last_seg:1;
- 	u8 first_seg:1;
--	u16 additional_cdata_size:8;
-+	u8 additional_cdata_size:8;
- 
- 	u32 rsvd1;
- 
- 	u32 data_lo;
- 	u32 data_hi;
- 
-+	u32 atok_lo;
-+	u32 atok_hi;
-+
- 	struct safexcel_control_data_desc control_data;
- } __packed;
- 
-+#define EIP197_CD64_FETCH_SIZE		(sizeof(struct safexcel_command_desc) /\
-+					sizeof(u32))
-+
- /*
-  * Internal structures & functions
-  */
-@@ -578,15 +638,20 @@ enum eip197_fw {
- 
- struct safexcel_desc_ring {
- 	void *base;
-+	void *shbase;
- 	void *base_end;
-+	void *shbase_end;
- 	dma_addr_t base_dma;
-+	dma_addr_t shbase_dma;
- 
- 	/* write and read pointers */
- 	void *write;
-+	void *shwrite;
- 	void *read;
- 
- 	/* descriptor element offset */
--	unsigned offset;
-+	unsigned int offset;
-+	unsigned int shoffset;
- };
- 
- enum safexcel_alg_type {
-@@ -601,9 +666,11 @@ struct safexcel_config {
- 
- 	u32 cd_size;
- 	u32 cd_offset;
-+	u32 cdsh_offset;
- 
- 	u32 rd_size;
- 	u32 rd_offset;
-+	u32 res_offset;
- };
- 
- struct safexcel_work_data {
-@@ -654,6 +721,12 @@ enum safexcel_eip_version {
- /* Priority we use for advertising our algorithms */
- #define SAFEXCEL_CRA_PRIORITY		300
- 
-+/* SM3 digest result for zero length message */
-+#define EIP197_SM3_ZEROM_HASH	"\x1A\xB2\x1D\x83\x55\xCF\xA1\x7F" \
-+				"\x8E\x61\x19\x48\x31\xE8\x1A\x8F" \
-+				"\x22\xBE\xC8\xC7\x28\xFE\xFB\x74" \
-+				"\x7E\xD0\x35\xEB\x50\x82\xAA\x2B"
-+
- /* EIP algorithm presence flags */
- enum safexcel_eip_algorithms {
- 	SAFEXCEL_ALG_BC0      = BIT(5),
-@@ -697,16 +770,23 @@ struct safexcel_register_offsets {
- enum safexcel_flags {
- 	EIP197_TRC_CACHE	= BIT(0),
- 	SAFEXCEL_HW_EIP197	= BIT(1),
-+	EIP197_PE_ARB		= BIT(2),
-+	EIP197_ICE		= BIT(3),
-+	EIP197_SIMPLE_TRC	= BIT(4),
- };
- 
- struct safexcel_hwconfig {
- 	enum safexcel_eip_algorithms algo_flags;
- 	int hwver;
- 	int hiaver;
-+	int ppver;
- 	int pever;
- 	int hwdataw;
- 	int hwcfsize;
- 	int hwrfsize;
-+	int hwnumpes;
-+	int hwnumrings;
-+	int hwnumraic;
- };
- 
- struct safexcel_crypto_priv {
-@@ -778,7 +858,7 @@ struct safexcel_inv_result {
- 
- void safexcel_dequeue(struct safexcel_crypto_priv *priv, int ring);
- int safexcel_rdesc_check_errors(struct safexcel_crypto_priv *priv,
--				struct safexcel_result_desc *rdesc);
-+				void *rdp);
- void safexcel_complete(struct safexcel_crypto_priv *priv, int ring);
- int safexcel_invalidate_cache(struct crypto_async_request *async,
- 			      struct safexcel_crypto_priv *priv,
-@@ -797,7 +877,8 @@ struct safexcel_command_desc *safexcel_a
- 						 bool first, bool last,
- 						 dma_addr_t data, u32 len,
- 						 u32 full_data_len,
--						 dma_addr_t context);
-+						 dma_addr_t context,
-+						 struct safexcel_token **atoken);
- struct safexcel_result_desc *safexcel_add_rdesc(struct safexcel_crypto_priv *priv,
- 						 int ring_id,
- 						bool first, bool last,
-@@ -853,5 +934,43 @@ extern struct safexcel_alg_template safe
- extern struct safexcel_alg_template safexcel_alg_xts_aes;
- extern struct safexcel_alg_template safexcel_alg_gcm;
- extern struct safexcel_alg_template safexcel_alg_ccm;
-+extern struct safexcel_alg_template safexcel_alg_crc32;
-+extern struct safexcel_alg_template safexcel_alg_cbcmac;
-+extern struct safexcel_alg_template safexcel_alg_xcbcmac;
-+extern struct safexcel_alg_template safexcel_alg_cmac;
-+extern struct safexcel_alg_template safexcel_alg_chacha20;
-+extern struct safexcel_alg_template safexcel_alg_chachapoly;
-+extern struct safexcel_alg_template safexcel_alg_chachapoly_esp;
-+extern struct safexcel_alg_template safexcel_alg_sm3;
-+extern struct safexcel_alg_template safexcel_alg_hmac_sm3;
-+extern struct safexcel_alg_template safexcel_alg_ecb_sm4;
-+extern struct safexcel_alg_template safexcel_alg_cbc_sm4;
-+extern struct safexcel_alg_template safexcel_alg_ofb_sm4;
-+extern struct safexcel_alg_template safexcel_alg_cfb_sm4;
-+extern struct safexcel_alg_template safexcel_alg_ctr_sm4;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha1_cbc_sm4;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sm3_cbc_sm4;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha1_ctr_sm4;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sm3_ctr_sm4;
-+extern struct safexcel_alg_template safexcel_alg_sha3_224;
-+extern struct safexcel_alg_template safexcel_alg_sha3_256;
-+extern struct safexcel_alg_template safexcel_alg_sha3_384;
-+extern struct safexcel_alg_template safexcel_alg_sha3_512;
-+extern struct safexcel_alg_template safexcel_alg_hmac_sha3_224;
-+extern struct safexcel_alg_template safexcel_alg_hmac_sha3_256;
-+extern struct safexcel_alg_template safexcel_alg_hmac_sha3_384;
-+extern struct safexcel_alg_template safexcel_alg_hmac_sha3_512;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha1_cbc_des;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha256_cbc_des3_ede;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha224_cbc_des3_ede;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha512_cbc_des3_ede;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha384_cbc_des3_ede;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha256_cbc_des;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha224_cbc_des;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha512_cbc_des;
-+extern struct safexcel_alg_template safexcel_alg_authenc_hmac_sha384_cbc_des;
-+extern struct safexcel_alg_template safexcel_alg_rfc4106_gcm;
-+extern struct safexcel_alg_template safexcel_alg_rfc4543_gcm;
-+extern struct safexcel_alg_template safexcel_alg_rfc4309_ccm;
- 
- #endif
---- a/drivers/crypto/inside-secure/safexcel_hash.c
-+++ b/drivers/crypto/inside-secure/safexcel_hash.c
-@@ -5,9 +5,13 @@
-  * Antoine Tenart <antoine.tenart@free-electrons.com>
-  */
- 
-+#include <crypto/aes.h>
- #include <crypto/hmac.h>
- #include <crypto/md5.h>
- #include <crypto/sha.h>
-+#include <crypto/sha3.h>
-+#include <crypto/skcipher.h>
-+#include <crypto/sm3.h>
- #include <linux/device.h>
- #include <linux/dma-mapping.h>
- #include <linux/dmapool.h>
-@@ -19,9 +23,19 @@ struct safexcel_ahash_ctx {
- 	struct safexcel_crypto_priv *priv;
- 
- 	u32 alg;
--
--	u32 ipad[SHA512_DIGEST_SIZE / sizeof(u32)];
--	u32 opad[SHA512_DIGEST_SIZE / sizeof(u32)];
-+	u8  key_sz;
-+	bool cbcmac;
-+	bool do_fallback;
-+	bool fb_init_done;
-+	bool fb_do_setkey;
-+
-+	__le32 ipad[SHA3_512_BLOCK_SIZE / sizeof(__le32)];
-+	__le32 opad[SHA3_512_BLOCK_SIZE / sizeof(__le32)];
-+
-+	struct crypto_cipher *kaes;
-+	struct crypto_ahash *fback;
-+	struct crypto_shash *shpre;
-+	struct shash_desc *shdesc;
- };
- 
- struct safexcel_ahash_req {
-@@ -31,6 +45,8 @@ struct safexcel_ahash_req {
- 	bool needs_inv;
- 	bool hmac_zlen;
- 	bool len_is_le;
-+	bool not_first;
-+	bool xcbcmac;
- 
- 	int nents;
- 	dma_addr_t result_dma;
-@@ -39,7 +55,9 @@ struct safexcel_ahash_req {
- 
- 	u8 state_sz;    /* expected state size, only set once */
- 	u8 block_sz;    /* block size, only set once */
--	u32 state[SHA512_DIGEST_SIZE / sizeof(u32)] __aligned(sizeof(u32));
-+	u8 digest_sz;   /* output digest size, only set once */
-+	__le32 state[SHA3_512_BLOCK_SIZE /
-+		     sizeof(__le32)] __aligned(sizeof(__le32));
- 
- 	u64 len;
- 	u64 processed;
-@@ -57,22 +75,36 @@ static inline u64 safexcel_queued_len(st
- }
- 
- static void safexcel_hash_token(struct safexcel_command_desc *cdesc,
--				u32 input_length, u32 result_length)
-+				u32 input_length, u32 result_length,
-+				bool cbcmac)
- {
- 	struct safexcel_token *token =
- 		(struct safexcel_token *)cdesc->control_data.token;
- 
- 	token[0].opcode = EIP197_TOKEN_OPCODE_DIRECTION;
- 	token[0].packet_length = input_length;
--	token[0].stat = EIP197_TOKEN_STAT_LAST_HASH;
- 	token[0].instructions = EIP197_TOKEN_INS_TYPE_HASH;
- 
--	token[1].opcode = EIP197_TOKEN_OPCODE_INSERT;
--	token[1].packet_length = result_length;
--	token[1].stat = EIP197_TOKEN_STAT_LAST_HASH |
-+	input_length &= 15;
-+	if (unlikely(cbcmac && input_length)) {
-+		token[0].stat =  0;
-+		token[1].opcode = EIP197_TOKEN_OPCODE_INSERT;
-+		token[1].packet_length = 16 - input_length;
-+		token[1].stat = EIP197_TOKEN_STAT_LAST_HASH;
-+		token[1].instructions = EIP197_TOKEN_INS_TYPE_HASH;
-+	} else {
-+		token[0].stat = EIP197_TOKEN_STAT_LAST_HASH;
-+		eip197_noop_token(&token[1]);
-+	}
-+
-+	token[2].opcode = EIP197_TOKEN_OPCODE_INSERT;
-+	token[2].stat = EIP197_TOKEN_STAT_LAST_HASH |
- 			EIP197_TOKEN_STAT_LAST_PACKET;
--	token[1].instructions = EIP197_TOKEN_INS_TYPE_OUTPUT |
-+	token[2].packet_length = result_length;
-+	token[2].instructions = EIP197_TOKEN_INS_TYPE_OUTPUT |
- 				EIP197_TOKEN_INS_INSERT_HASH_DIGEST;
-+
-+	eip197_noop_token(&token[3]);
- }
- 
- static void safexcel_context_control(struct safexcel_ahash_ctx *ctx,
-@@ -82,29 +114,49 @@ static void safexcel_context_control(str
- 	struct safexcel_crypto_priv *priv = ctx->priv;
- 	u64 count = 0;
- 
--	cdesc->control_data.control0 |= ctx->alg;
-+	cdesc->control_data.control0 = ctx->alg;
-+	cdesc->control_data.control1 = 0;
- 
- 	/*
- 	 * Copy the input digest if needed, and setup the context
- 	 * fields. Do this now as we need it to setup the first command
- 	 * descriptor.
- 	 */
--	if (!req->processed) {
--		/* First - and possibly only - block of basic hash only */
--		if (req->finish) {
-+	if (unlikely(req->digest == CONTEXT_CONTROL_DIGEST_XCM)) {
-+		if (req->xcbcmac)
-+			memcpy(ctx->base.ctxr->data, ctx->ipad, ctx->key_sz);
-+		else
-+			memcpy(ctx->base.ctxr->data, req->state, req->state_sz);
-+
-+		if (!req->finish && req->xcbcmac)
-+			cdesc->control_data.control0 |=
-+				CONTEXT_CONTROL_DIGEST_XCM |
-+				CONTEXT_CONTROL_TYPE_HASH_OUT  |
-+				CONTEXT_CONTROL_NO_FINISH_HASH |
-+				CONTEXT_CONTROL_SIZE(req->state_sz /
-+						     sizeof(u32));
-+		else
- 			cdesc->control_data.control0 |=
-+				CONTEXT_CONTROL_DIGEST_XCM |
-+				CONTEXT_CONTROL_TYPE_HASH_OUT  |
-+				CONTEXT_CONTROL_SIZE(req->state_sz /
-+						     sizeof(u32));
-+		return;
-+	} else if (!req->processed) {
-+		/* First - and possibly only - block of basic hash only */
-+		if (req->finish)
-+			cdesc->control_data.control0 |= req->digest |
- 				CONTEXT_CONTROL_TYPE_HASH_OUT |
- 				CONTEXT_CONTROL_RESTART_HASH  |
- 				/* ensure its not 0! */
- 				CONTEXT_CONTROL_SIZE(1);
--		} else {
--			cdesc->control_data.control0 |=
-+		else
-+			cdesc->control_data.control0 |= req->digest |
- 				CONTEXT_CONTROL_TYPE_HASH_OUT  |
- 				CONTEXT_CONTROL_RESTART_HASH   |
- 				CONTEXT_CONTROL_NO_FINISH_HASH |
- 				/* ensure its not 0! */
- 				CONTEXT_CONTROL_SIZE(1);
--		}
- 		return;
- 	}
- 
-@@ -204,7 +256,7 @@ static int safexcel_handle_req_result(st
- 	}
- 
- 	if (sreq->result_dma) {
--		dma_unmap_single(priv->dev, sreq->result_dma, sreq->state_sz,
-+		dma_unmap_single(priv->dev, sreq->result_dma, sreq->digest_sz,
- 				 DMA_FROM_DEVICE);
- 		sreq->result_dma = 0;
- 	}
-@@ -223,14 +275,15 @@ static int safexcel_handle_req_result(st
- 			memcpy(sreq->cache, sreq->state,
- 			       crypto_ahash_digestsize(ahash));
- 
--			memcpy(sreq->state, ctx->opad, sreq->state_sz);
-+			memcpy(sreq->state, ctx->opad, sreq->digest_sz);
- 
- 			sreq->len = sreq->block_sz +
- 				    crypto_ahash_digestsize(ahash);
- 			sreq->processed = sreq->block_sz;
- 			sreq->hmac = 0;
- 
--			ctx->base.needs_inv = true;
-+			if (priv->flags & EIP197_TRC_CACHE)
-+				ctx->base.needs_inv = true;
- 			areq->nbytes = 0;
- 			safexcel_ahash_enqueue(areq);
- 
-@@ -238,8 +291,14 @@ static int safexcel_handle_req_result(st
- 			return 1;
- 		}
- 
--		memcpy(areq->result, sreq->state,
--		       crypto_ahash_digestsize(ahash));
-+		if (unlikely(sreq->digest == CONTEXT_CONTROL_DIGEST_XCM &&
-+			     ctx->alg == CONTEXT_CONTROL_CRYPTO_ALG_CRC32)) {
-+			/* Undo final XOR with 0xffffffff ...*/
-+			*(__le32 *)areq->result = ~sreq->state[0];
-+		} else {
-+			memcpy(areq->result, sreq->state,
-+			       crypto_ahash_digestsize(ahash));
-+		}
- 	}
- 
- 	cache_len = safexcel_queued_len(sreq);
-@@ -261,10 +320,11 @@ static int safexcel_ahash_send_req(struc
- 	struct safexcel_command_desc *cdesc, *first_cdesc = NULL;
- 	struct safexcel_result_desc *rdesc;
- 	struct scatterlist *sg;
--	int i, extra = 0, n_cdesc = 0, ret = 0;
--	u64 queued, len, cache_len;
-+	struct safexcel_token *dmmy;
-+	int i, extra = 0, n_cdesc = 0, ret = 0, cache_len, skip = 0;
-+	u64 queued, len;
- 
--	queued = len = safexcel_queued_len(req);
-+	queued = safexcel_queued_len(req);
- 	if (queued <= HASH_CACHE_SIZE)
- 		cache_len = queued;
- 	else
-@@ -287,15 +347,52 @@ static int safexcel_ahash_send_req(struc
- 				   areq->nbytes - extra);
- 
- 		queued -= extra;
--		len -= extra;
- 
- 		if (!queued) {
- 			*commands = 0;
- 			*results = 0;
- 			return 0;
- 		}
-+
-+		extra = 0;
-+	}
-+
-+	if (unlikely(req->xcbcmac && req->processed > AES_BLOCK_SIZE)) {
-+		if (unlikely(cache_len < AES_BLOCK_SIZE)) {
-+			/*
-+			 * Cache contains less than 1 full block, complete.
-+			 */
-+			extra = AES_BLOCK_SIZE - cache_len;
-+			if (queued > cache_len) {
-+				/* More data follows: borrow bytes */
-+				u64 tmp = queued - cache_len;
-+
-+				skip = min_t(u64, tmp, extra);
-+				sg_pcopy_to_buffer(areq->src,
-+					sg_nents(areq->src),
-+					req->cache + cache_len,
-+					skip, 0);
-+			}
-+			extra -= skip;
-+			memset(req->cache + cache_len + skip, 0, extra);
-+			if (!ctx->cbcmac && extra) {
-+				// 10- padding for XCBCMAC & CMAC
-+				req->cache[cache_len + skip] = 0x80;
-+				// HW will use K2 iso K3 - compensate!
-+				for (i = 0; i < AES_BLOCK_SIZE / sizeof(u32); i++)
-+					((__be32 *)req->cache)[i] ^=
-+					  cpu_to_be32(le32_to_cpu(
-+					    ctx->ipad[i] ^ ctx->ipad[i + 4]));
-+			}
-+			cache_len = AES_BLOCK_SIZE;
-+			queued = queued + extra;
-+		}
-+
-+		/* XCBC continue: XOR previous result into 1st word */
-+		crypto_xor(req->cache, (const u8 *)req->state, AES_BLOCK_SIZE);
- 	}
- 
-+	len = queued;
- 	/* Add a command descriptor for the cached data, if any */
- 	if (cache_len) {
- 		req->cache_dma = dma_map_single(priv->dev, req->cache,
-@@ -306,8 +403,9 @@ static int safexcel_ahash_send_req(struc
- 		req->cache_sz = cache_len;
- 		first_cdesc = safexcel_add_cdesc(priv, ring, 1,
- 						 (cache_len == len),
--						 req->cache_dma, cache_len, len,
--						 ctx->base.ctxr_dma);
-+						 req->cache_dma, cache_len,
-+						 len, ctx->base.ctxr_dma,
-+						 &dmmy);
- 		if (IS_ERR(first_cdesc)) {
- 			ret = PTR_ERR(first_cdesc);
- 			goto unmap_cache;
-@@ -319,10 +417,6 @@ static int safexcel_ahash_send_req(struc
- 			goto send_command;
- 	}
- 
--	/* Skip descriptor generation for zero-length requests */
--	if (!areq->nbytes)
--		goto send_command;
--
- 	/* Now handle the current ahash request buffer(s) */
- 	req->nents = dma_map_sg(priv->dev, areq->src,
- 				sg_nents_for_len(areq->src,
-@@ -336,26 +430,34 @@ static int safexcel_ahash_send_req(struc
- 	for_each_sg(areq->src, sg, req->nents, i) {
- 		int sglen = sg_dma_len(sg);
- 
-+		if (unlikely(sglen <= skip)) {
-+			skip -= sglen;
-+			continue;
-+		}
-+
- 		/* Do not overflow the request */
--		if (queued < sglen)
-+		if ((queued + skip) <= sglen)
- 			sglen = queued;
-+		else
-+			sglen -= skip;
- 
- 		cdesc = safexcel_add_cdesc(priv, ring, !n_cdesc,
- 					   !(queued - sglen),
--					   sg_dma_address(sg),
--					   sglen, len, ctx->base.ctxr_dma);
-+					   sg_dma_address(sg) + skip, sglen,
-+					   len, ctx->base.ctxr_dma, &dmmy);
- 		if (IS_ERR(cdesc)) {
- 			ret = PTR_ERR(cdesc);
- 			goto unmap_sg;
- 		}
--		n_cdesc++;
- 
--		if (n_cdesc == 1)
-+		if (!n_cdesc)
- 			first_cdesc = cdesc;
-+		n_cdesc++;
- 
- 		queued -= sglen;
- 		if (!queued)
- 			break;
-+		skip = 0;
- 	}
- 
- send_command:
-@@ -363,9 +465,9 @@ send_command:
- 	safexcel_context_control(ctx, req, first_cdesc);
- 
- 	/* Add the token */
--	safexcel_hash_token(first_cdesc, len, req->state_sz);
-+	safexcel_hash_token(first_cdesc, len, req->digest_sz, ctx->cbcmac);
- 
--	req->result_dma = dma_map_single(priv->dev, req->state, req->state_sz,
-+	req->result_dma = dma_map_single(priv->dev, req->state, req->digest_sz,
- 					 DMA_FROM_DEVICE);
- 	if (dma_mapping_error(priv->dev, req->result_dma)) {
- 		ret = -EINVAL;
-@@ -374,7 +476,7 @@ send_command:
- 
- 	/* Add a result descriptor */
- 	rdesc = safexcel_add_rdesc(priv, ring, 1, 1, req->result_dma,
--				   req->state_sz);
-+				   req->digest_sz);
- 	if (IS_ERR(rdesc)) {
- 		ret = PTR_ERR(rdesc);
- 		goto unmap_result;
-@@ -382,17 +484,20 @@ send_command:
- 
- 	safexcel_rdr_req_set(priv, ring, rdesc, &areq->base);
- 
--	req->processed += len;
-+	req->processed += len - extra;
- 
- 	*commands = n_cdesc;
- 	*results = 1;
- 	return 0;
- 
- unmap_result:
--	dma_unmap_single(priv->dev, req->result_dma, req->state_sz,
-+	dma_unmap_single(priv->dev, req->result_dma, req->digest_sz,
- 			 DMA_FROM_DEVICE);
- unmap_sg:
--	dma_unmap_sg(priv->dev, areq->src, req->nents, DMA_TO_DEVICE);
-+	if (req->nents) {
-+		dma_unmap_sg(priv->dev, areq->src, req->nents, DMA_TO_DEVICE);
-+		req->nents = 0;
-+	}
- cdesc_rollback:
- 	for (i = 0; i < n_cdesc; i++)
- 		safexcel_ring_rollback_wptr(priv, &priv->ring[ring].cdr);
-@@ -590,16 +695,12 @@ static int safexcel_ahash_enqueue(struct
- 
- 	if (ctx->base.ctxr) {
- 		if (priv->flags & EIP197_TRC_CACHE && !ctx->base.needs_inv &&
--		    req->processed &&
--		    (/* invalidate for basic hash continuation finish */
--		     (req->finish &&
--		      (req->digest == CONTEXT_CONTROL_DIGEST_PRECOMPUTED)) ||
-+		     /* invalidate for *any* non-XCBC continuation */
-+		   ((req->not_first && !req->xcbcmac) ||
- 		     /* invalidate if (i)digest changed */
- 		     memcmp(ctx->base.ctxr->data, req->state, req->state_sz) ||
--		     /* invalidate for HMAC continuation finish */
--		     (req->finish && (req->processed != req->block_sz)) ||
- 		     /* invalidate for HMAC finish with odigest changed */
--		     (req->finish &&
-+		     (req->finish && req->hmac &&
- 		      memcmp(ctx->base.ctxr->data + (req->state_sz>>2),
- 			     ctx->opad, req->state_sz))))
- 			/*
-@@ -622,6 +723,7 @@ static int safexcel_ahash_enqueue(struct
- 		if (!ctx->base.ctxr)
- 			return -ENOMEM;
- 	}
-+	req->not_first = true;
- 
- 	ring = ctx->base.ring;
- 
-@@ -691,8 +793,34 @@ static int safexcel_ahash_final(struct a
- 		else if (ctx->alg == CONTEXT_CONTROL_CRYPTO_ALG_SHA512)
- 			memcpy(areq->result, sha512_zero_message_hash,
- 			       SHA512_DIGEST_SIZE);
-+		else if (ctx->alg == CONTEXT_CONTROL_CRYPTO_ALG_SM3) {
-+			memcpy(areq->result,
-+			       EIP197_SM3_ZEROM_HASH, SM3_DIGEST_SIZE);
-+		}
- 
- 		return 0;
-+	} else if (unlikely(req->digest == CONTEXT_CONTROL_DIGEST_XCM &&
-+			    ctx->alg == CONTEXT_CONTROL_CRYPTO_ALG_MD5 &&
-+			    req->len == sizeof(u32) && !areq->nbytes)) {
-+		/* Zero length CRC32 */
-+		memcpy(areq->result, ctx->ipad, sizeof(u32));
-+		return 0;
-+	} else if (unlikely(ctx->cbcmac && req->len == AES_BLOCK_SIZE &&
-+			    !areq->nbytes)) {
-+		/* Zero length CBC MAC */
-+		memset(areq->result, 0, AES_BLOCK_SIZE);
-+		return 0;
-+	} else if (unlikely(req->xcbcmac && req->len == AES_BLOCK_SIZE &&
-+			    !areq->nbytes)) {
-+		/* Zero length (X)CBC/CMAC */
-+		int i;
-+
-+		for (i = 0; i < AES_BLOCK_SIZE / sizeof(u32); i++)
-+			((__be32 *)areq->result)[i] =
-+				cpu_to_be32(le32_to_cpu(ctx->ipad[i + 4]));//K3
-+		areq->result[0] ^= 0x80;			// 10- padding
-+		crypto_cipher_encrypt_one(ctx->kaes, areq->result, areq->result);
-+		return 0;
- 	} else if (unlikely(req->hmac &&
- 			    (req->len == req->block_sz) &&
- 			    !areq->nbytes)) {
-@@ -792,6 +920,7 @@ static int safexcel_ahash_cra_init(struc
- 	ctx->priv = tmpl->priv;
- 	ctx->base.send = safexcel_ahash_send;
- 	ctx->base.handle_result = safexcel_handle_result;
-+	ctx->fb_do_setkey = false;
- 
- 	crypto_ahash_set_reqsize(__crypto_ahash_cast(tfm),
- 				 sizeof(struct safexcel_ahash_req));
-@@ -808,6 +937,7 @@ static int safexcel_sha1_init(struct aha
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA1;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA1_DIGEST_SIZE;
-+	req->digest_sz = SHA1_DIGEST_SIZE;
- 	req->block_sz = SHA1_BLOCK_SIZE;
- 
- 	return 0;
-@@ -889,6 +1019,7 @@ static int safexcel_hmac_sha1_init(struc
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA1;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA1_DIGEST_SIZE;
-+	req->digest_sz = SHA1_DIGEST_SIZE;
- 	req->block_sz = SHA1_BLOCK_SIZE;
- 	req->hmac = true;
- 
-@@ -1125,6 +1256,7 @@ static int safexcel_sha256_init(struct a
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA256;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA256_DIGEST_SIZE;
-+	req->digest_sz = SHA256_DIGEST_SIZE;
- 	req->block_sz = SHA256_BLOCK_SIZE;
- 
- 	return 0;
-@@ -1180,6 +1312,7 @@ static int safexcel_sha224_init(struct a
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA224;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA256_DIGEST_SIZE;
-+	req->digest_sz = SHA256_DIGEST_SIZE;
- 	req->block_sz = SHA256_BLOCK_SIZE;
- 
- 	return 0;
-@@ -1248,6 +1381,7 @@ static int safexcel_hmac_sha224_init(str
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA224;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA256_DIGEST_SIZE;
-+	req->digest_sz = SHA256_DIGEST_SIZE;
- 	req->block_sz = SHA256_BLOCK_SIZE;
- 	req->hmac = true;
- 
-@@ -1318,6 +1452,7 @@ static int safexcel_hmac_sha256_init(str
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA256;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA256_DIGEST_SIZE;
-+	req->digest_sz = SHA256_DIGEST_SIZE;
- 	req->block_sz = SHA256_BLOCK_SIZE;
- 	req->hmac = true;
- 
-@@ -1375,6 +1510,7 @@ static int safexcel_sha512_init(struct a
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA512;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA512_DIGEST_SIZE;
-+	req->digest_sz = SHA512_DIGEST_SIZE;
- 	req->block_sz = SHA512_BLOCK_SIZE;
- 
- 	return 0;
-@@ -1430,6 +1566,7 @@ static int safexcel_sha384_init(struct a
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA384;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA512_DIGEST_SIZE;
-+	req->digest_sz = SHA512_DIGEST_SIZE;
- 	req->block_sz = SHA512_BLOCK_SIZE;
- 
- 	return 0;
-@@ -1498,6 +1635,7 @@ static int safexcel_hmac_sha512_init(str
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA512;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA512_DIGEST_SIZE;
-+	req->digest_sz = SHA512_DIGEST_SIZE;
- 	req->block_sz = SHA512_BLOCK_SIZE;
- 	req->hmac = true;
- 
-@@ -1568,6 +1706,7 @@ static int safexcel_hmac_sha384_init(str
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA384;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = SHA512_DIGEST_SIZE;
-+	req->digest_sz = SHA512_DIGEST_SIZE;
- 	req->block_sz = SHA512_BLOCK_SIZE;
- 	req->hmac = true;
- 
-@@ -1625,6 +1764,7 @@ static int safexcel_md5_init(struct ahas
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_MD5;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = MD5_DIGEST_SIZE;
-+	req->digest_sz = MD5_DIGEST_SIZE;
- 	req->block_sz = MD5_HMAC_BLOCK_SIZE;
- 
- 	return 0;
-@@ -1686,6 +1826,7 @@ static int safexcel_hmac_md5_init(struct
- 	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_MD5;
- 	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
- 	req->state_sz = MD5_DIGEST_SIZE;
-+	req->digest_sz = MD5_DIGEST_SIZE;
- 	req->block_sz = MD5_HMAC_BLOCK_SIZE;
- 	req->len_is_le = true; /* MD5 is little endian! ... */
- 	req->hmac = true;
-@@ -1738,5 +1879,1235 @@ struct safexcel_alg_template safexcel_al
- 				.cra_module = THIS_MODULE,
- 			},
- 		},
-+	},
-+};
-+
-+static int safexcel_crc32_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(tfm);
-+	int ret = safexcel_ahash_cra_init(tfm);
-+
-+	/* Default 'key' is all zeroes */
-+	memset(ctx->ipad, 0, sizeof(u32));
-+	return ret;
-+}
-+
-+static int safexcel_crc32_init(struct ahash_request *areq)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(crypto_ahash_reqtfm(areq));
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	/* Start from loaded key */
-+	req->state[0]	= (__force __le32)le32_to_cpu(~ctx->ipad[0]);
-+	/* Set processed to non-zero to enable invalidation detection */
-+	req->len	= sizeof(u32);
-+	req->processed	= sizeof(u32);
-+
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_CRC32;
-+	req->digest = CONTEXT_CONTROL_DIGEST_XCM;
-+	req->state_sz = sizeof(u32);
-+	req->digest_sz = sizeof(u32);
-+	req->block_sz = sizeof(u32);
-+
-+	return 0;
-+}
-+
-+static int safexcel_crc32_setkey(struct crypto_ahash *tfm, const u8 *key,
-+				 unsigned int keylen)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(crypto_ahash_tfm(tfm));
-+
-+	if (keylen != sizeof(u32))
-+		return -EINVAL;
-+
-+	memcpy(ctx->ipad, key, sizeof(u32));
-+	return 0;
-+}
-+
-+static int safexcel_crc32_digest(struct ahash_request *areq)
-+{
-+	return safexcel_crc32_init(areq) ?: safexcel_ahash_finup(areq);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_crc32 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = 0,
-+	.alg.ahash = {
-+		.init = safexcel_crc32_init,
-+		.update = safexcel_ahash_update,
-+		.final = safexcel_ahash_final,
-+		.finup = safexcel_ahash_finup,
-+		.digest = safexcel_crc32_digest,
-+		.setkey = safexcel_crc32_setkey,
-+		.export = safexcel_ahash_export,
-+		.import = safexcel_ahash_import,
-+		.halg = {
-+			.digestsize = sizeof(u32),
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "crc32",
-+				.cra_driver_name = "safexcel-crc32",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_OPTIONAL_KEY |
-+					     CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+				.cra_blocksize = 1,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_crc32_cra_init,
-+				.cra_exit = safexcel_ahash_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_cbcmac_init(struct ahash_request *areq)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(crypto_ahash_reqtfm(areq));
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	/* Start from loaded keys */
-+	memcpy(req->state, ctx->ipad, ctx->key_sz);
-+	/* Set processed to non-zero to enable invalidation detection */
-+	req->len	= AES_BLOCK_SIZE;
-+	req->processed	= AES_BLOCK_SIZE;
-+
-+	req->digest   = CONTEXT_CONTROL_DIGEST_XCM;
-+	req->state_sz = ctx->key_sz;
-+	req->digest_sz = AES_BLOCK_SIZE;
-+	req->block_sz = AES_BLOCK_SIZE;
-+	req->xcbcmac  = true;
-+
-+	return 0;
-+}
-+
-+static int safexcel_cbcmac_setkey(struct crypto_ahash *tfm, const u8 *key,
-+				 unsigned int len)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(crypto_ahash_tfm(tfm));
-+	struct crypto_aes_ctx aes;
-+	int ret, i;
-+
-+	ret = aes_expandkey(&aes, key, len);
-+	if (ret)
-+		return ret;
-+
-+	memset(ctx->ipad, 0, 2 * AES_BLOCK_SIZE);
-+	for (i = 0; i < len / sizeof(u32); i++)
-+		ctx->ipad[i + 8] = (__force __le32)cpu_to_be32(aes.key_enc[i]);
-+
-+	if (len == AES_KEYSIZE_192) {
-+		ctx->alg    = CONTEXT_CONTROL_CRYPTO_ALG_XCBC192;
-+		ctx->key_sz = AES_MAX_KEY_SIZE + 2 * AES_BLOCK_SIZE;
-+	} else if (len == AES_KEYSIZE_256) {
-+		ctx->alg    = CONTEXT_CONTROL_CRYPTO_ALG_XCBC256;
-+		ctx->key_sz = AES_MAX_KEY_SIZE + 2 * AES_BLOCK_SIZE;
-+	} else {
-+		ctx->alg    = CONTEXT_CONTROL_CRYPTO_ALG_XCBC128;
-+		ctx->key_sz = AES_MIN_KEY_SIZE + 2 * AES_BLOCK_SIZE;
-+	}
-+	ctx->cbcmac  = true;
-+
-+	memzero_explicit(&aes, sizeof(aes));
-+	return 0;
-+}
-+
-+static int safexcel_cbcmac_digest(struct ahash_request *areq)
-+{
-+	return safexcel_cbcmac_init(areq) ?: safexcel_ahash_finup(areq);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_cbcmac = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = 0,
-+	.alg.ahash = {
-+		.init = safexcel_cbcmac_init,
-+		.update = safexcel_ahash_update,
-+		.final = safexcel_ahash_final,
-+		.finup = safexcel_ahash_finup,
-+		.digest = safexcel_cbcmac_digest,
-+		.setkey = safexcel_cbcmac_setkey,
-+		.export = safexcel_ahash_export,
-+		.import = safexcel_ahash_import,
-+		.halg = {
-+			.digestsize = AES_BLOCK_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "cbcmac(aes)",
-+				.cra_driver_name = "safexcel-cbcmac-aes",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+				.cra_blocksize = 1,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_ahash_cra_init,
-+				.cra_exit = safexcel_ahash_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_xcbcmac_setkey(struct crypto_ahash *tfm, const u8 *key,
-+				 unsigned int len)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(crypto_ahash_tfm(tfm));
-+	struct crypto_aes_ctx aes;
-+	u32 key_tmp[3 * AES_BLOCK_SIZE / sizeof(u32)];
-+	int ret, i;
-+
-+	ret = aes_expandkey(&aes, key, len);
-+	if (ret)
-+		return ret;
-+
-+	/* precompute the XCBC key material */
-+	crypto_cipher_clear_flags(ctx->kaes, CRYPTO_TFM_REQ_MASK);
-+	crypto_cipher_set_flags(ctx->kaes, crypto_ahash_get_flags(tfm) &
-+				CRYPTO_TFM_REQ_MASK);
-+	ret = crypto_cipher_setkey(ctx->kaes, key, len);
-+	if (ret)
-+		return ret;
-+
-+	crypto_cipher_encrypt_one(ctx->kaes, (u8 *)key_tmp + 2 * AES_BLOCK_SIZE,
-+		"\x1\x1\x1\x1\x1\x1\x1\x1\x1\x1\x1\x1\x1\x1\x1\x1");
-+	crypto_cipher_encrypt_one(ctx->kaes, (u8 *)key_tmp,
-+		"\x2\x2\x2\x2\x2\x2\x2\x2\x2\x2\x2\x2\x2\x2\x2\x2");
-+	crypto_cipher_encrypt_one(ctx->kaes, (u8 *)key_tmp + AES_BLOCK_SIZE,
-+		"\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3\x3");
-+	for (i = 0; i < 3 * AES_BLOCK_SIZE / sizeof(u32); i++)
-+		ctx->ipad[i] =
-+			cpu_to_le32((__force u32)cpu_to_be32(key_tmp[i]));
-+
-+	crypto_cipher_clear_flags(ctx->kaes, CRYPTO_TFM_REQ_MASK);
-+	crypto_cipher_set_flags(ctx->kaes, crypto_ahash_get_flags(tfm) &
-+				CRYPTO_TFM_REQ_MASK);
-+	ret = crypto_cipher_setkey(ctx->kaes,
-+				   (u8 *)key_tmp + 2 * AES_BLOCK_SIZE,
-+				   AES_MIN_KEY_SIZE);
-+	if (ret)
-+		return ret;
-+
-+	ctx->alg    = CONTEXT_CONTROL_CRYPTO_ALG_XCBC128;
-+	ctx->key_sz = AES_MIN_KEY_SIZE + 2 * AES_BLOCK_SIZE;
-+	ctx->cbcmac = false;
-+
-+	memzero_explicit(&aes, sizeof(aes));
-+	return 0;
-+}
-+
-+static int safexcel_xcbcmac_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_ahash_cra_init(tfm);
-+	ctx->kaes = crypto_alloc_cipher("aes", 0, 0);
-+	return PTR_ERR_OR_ZERO(ctx->kaes);
-+}
-+
-+static void safexcel_xcbcmac_cra_exit(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	crypto_free_cipher(ctx->kaes);
-+	safexcel_ahash_cra_exit(tfm);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_xcbcmac = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = 0,
-+	.alg.ahash = {
-+		.init = safexcel_cbcmac_init,
-+		.update = safexcel_ahash_update,
-+		.final = safexcel_ahash_final,
-+		.finup = safexcel_ahash_finup,
-+		.digest = safexcel_cbcmac_digest,
-+		.setkey = safexcel_xcbcmac_setkey,
-+		.export = safexcel_ahash_export,
-+		.import = safexcel_ahash_import,
-+		.halg = {
-+			.digestsize = AES_BLOCK_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "xcbc(aes)",
-+				.cra_driver_name = "safexcel-xcbc-aes",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+				.cra_blocksize = AES_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_xcbcmac_cra_init,
-+				.cra_exit = safexcel_xcbcmac_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_cmac_setkey(struct crypto_ahash *tfm, const u8 *key,
-+				unsigned int len)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(crypto_ahash_tfm(tfm));
-+	struct crypto_aes_ctx aes;
-+	__be64 consts[4];
-+	u64 _const[2];
-+	u8 msb_mask, gfmask;
-+	int ret, i;
-+
-+	ret = aes_expandkey(&aes, key, len);
-+	if (ret)
-+		return ret;
-+
-+	for (i = 0; i < len / sizeof(u32); i++)
-+		ctx->ipad[i + 8] =
-+			cpu_to_le32((__force u32)cpu_to_be32(aes.key_enc[i]));
-+
-+	/* precompute the CMAC key material */
-+	crypto_cipher_clear_flags(ctx->kaes, CRYPTO_TFM_REQ_MASK);
-+	crypto_cipher_set_flags(ctx->kaes, crypto_ahash_get_flags(tfm) &
-+				CRYPTO_TFM_REQ_MASK);
-+	ret = crypto_cipher_setkey(ctx->kaes, key, len);
-+	if (ret)
-+		return ret;
-+
-+	/* code below borrowed from crypto/cmac.c */
-+	/* encrypt the zero block */
-+	memset(consts, 0, AES_BLOCK_SIZE);
-+	crypto_cipher_encrypt_one(ctx->kaes, (u8 *)consts, (u8 *)consts);
-+
-+	gfmask = 0x87;
-+	_const[0] = be64_to_cpu(consts[1]);
-+	_const[1] = be64_to_cpu(consts[0]);
-+
-+	/* gf(2^128) multiply zero-ciphertext with u and u^2 */
-+	for (i = 0; i < 4; i += 2) {
-+		msb_mask = ((s64)_const[1] >> 63) & gfmask;
-+		_const[1] = (_const[1] << 1) | (_const[0] >> 63);
-+		_const[0] = (_const[0] << 1) ^ msb_mask;
-+
-+		consts[i + 0] = cpu_to_be64(_const[1]);
-+		consts[i + 1] = cpu_to_be64(_const[0]);
-+	}
-+	/* end of code borrowed from crypto/cmac.c */
-+
-+	for (i = 0; i < 2 * AES_BLOCK_SIZE / sizeof(u32); i++)
-+		ctx->ipad[i] = (__force __le32)cpu_to_be32(((u32 *)consts)[i]);
-+
-+	if (len == AES_KEYSIZE_192) {
-+		ctx->alg    = CONTEXT_CONTROL_CRYPTO_ALG_XCBC192;
-+		ctx->key_sz = AES_MAX_KEY_SIZE + 2 * AES_BLOCK_SIZE;
-+	} else if (len == AES_KEYSIZE_256) {
-+		ctx->alg    = CONTEXT_CONTROL_CRYPTO_ALG_XCBC256;
-+		ctx->key_sz = AES_MAX_KEY_SIZE + 2 * AES_BLOCK_SIZE;
-+	} else {
-+		ctx->alg    = CONTEXT_CONTROL_CRYPTO_ALG_XCBC128;
-+		ctx->key_sz = AES_MIN_KEY_SIZE + 2 * AES_BLOCK_SIZE;
-+	}
-+	ctx->cbcmac = false;
-+
-+	memzero_explicit(&aes, sizeof(aes));
-+	return 0;
-+}
-+
-+struct safexcel_alg_template safexcel_alg_cmac = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = 0,
-+	.alg.ahash = {
-+		.init = safexcel_cbcmac_init,
-+		.update = safexcel_ahash_update,
-+		.final = safexcel_ahash_final,
-+		.finup = safexcel_ahash_finup,
-+		.digest = safexcel_cbcmac_digest,
-+		.setkey = safexcel_cmac_setkey,
-+		.export = safexcel_ahash_export,
-+		.import = safexcel_ahash_import,
-+		.halg = {
-+			.digestsize = AES_BLOCK_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "cmac(aes)",
-+				.cra_driver_name = "safexcel-cmac-aes",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+				.cra_blocksize = AES_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_xcbcmac_cra_init,
-+				.cra_exit = safexcel_xcbcmac_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_sm3_init(struct ahash_request *areq)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(crypto_ahash_reqtfm(areq));
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SM3;
-+	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
-+	req->state_sz = SM3_DIGEST_SIZE;
-+	req->digest_sz = SM3_DIGEST_SIZE;
-+	req->block_sz = SM3_BLOCK_SIZE;
-+
-+	return 0;
-+}
-+
-+static int safexcel_sm3_digest(struct ahash_request *areq)
-+{
-+	int ret = safexcel_sm3_init(areq);
-+
-+	if (ret)
-+		return ret;
-+
-+	return safexcel_ahash_finup(areq);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_sm3 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SM3,
-+	.alg.ahash = {
-+		.init = safexcel_sm3_init,
-+		.update = safexcel_ahash_update,
-+		.final = safexcel_ahash_final,
-+		.finup = safexcel_ahash_finup,
-+		.digest = safexcel_sm3_digest,
-+		.export = safexcel_ahash_export,
-+		.import = safexcel_ahash_import,
-+		.halg = {
-+			.digestsize = SM3_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "sm3",
-+				.cra_driver_name = "safexcel-sm3",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+				.cra_blocksize = SM3_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_ahash_cra_init,
-+				.cra_exit = safexcel_ahash_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_hmac_sm3_setkey(struct crypto_ahash *tfm, const u8 *key,
-+				    unsigned int keylen)
-+{
-+	return safexcel_hmac_alg_setkey(tfm, key, keylen, "safexcel-sm3",
-+					SM3_DIGEST_SIZE);
-+}
-+
-+static int safexcel_hmac_sm3_init(struct ahash_request *areq)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(crypto_ahash_reqtfm(areq));
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	/* Start from ipad precompute */
-+	memcpy(req->state, ctx->ipad, SM3_DIGEST_SIZE);
-+	/* Already processed the key^ipad part now! */
-+	req->len	= SM3_BLOCK_SIZE;
-+	req->processed	= SM3_BLOCK_SIZE;
-+
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SM3;
-+	req->digest = CONTEXT_CONTROL_DIGEST_PRECOMPUTED;
-+	req->state_sz = SM3_DIGEST_SIZE;
-+	req->digest_sz = SM3_DIGEST_SIZE;
-+	req->block_sz = SM3_BLOCK_SIZE;
-+	req->hmac = true;
-+
-+	return 0;
-+}
-+
-+static int safexcel_hmac_sm3_digest(struct ahash_request *areq)
-+{
-+	int ret = safexcel_hmac_sm3_init(areq);
-+
-+	if (ret)
-+		return ret;
-+
-+	return safexcel_ahash_finup(areq);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_hmac_sm3 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SM3,
-+	.alg.ahash = {
-+		.init = safexcel_hmac_sm3_init,
-+		.update = safexcel_ahash_update,
-+		.final = safexcel_ahash_final,
-+		.finup = safexcel_ahash_finup,
-+		.digest = safexcel_hmac_sm3_digest,
-+		.setkey = safexcel_hmac_sm3_setkey,
-+		.export = safexcel_ahash_export,
-+		.import = safexcel_ahash_import,
-+		.halg = {
-+			.digestsize = SM3_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "hmac(sm3)",
-+				.cra_driver_name = "safexcel-hmac-sm3",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY,
-+				.cra_blocksize = SM3_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_ahash_cra_init,
-+				.cra_exit = safexcel_ahash_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_sha3_224_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_224;
-+	req->digest = CONTEXT_CONTROL_DIGEST_INITIAL;
-+	req->state_sz = SHA3_224_DIGEST_SIZE;
-+	req->digest_sz = SHA3_224_DIGEST_SIZE;
-+	req->block_sz = SHA3_224_BLOCK_SIZE;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_sha3_fbcheck(struct ahash_request *req)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct ahash_request *subreq = ahash_request_ctx(req);
-+	int ret = 0;
-+
-+	if (ctx->do_fallback) {
-+		ahash_request_set_tfm(subreq, ctx->fback);
-+		ahash_request_set_callback(subreq, req->base.flags,
-+					   req->base.complete, req->base.data);
-+		ahash_request_set_crypt(subreq, req->src, req->result,
-+					req->nbytes);
-+		if (!ctx->fb_init_done) {
-+			if (ctx->fb_do_setkey) {
-+				/* Set fallback cipher HMAC key */
-+				u8 key[SHA3_224_BLOCK_SIZE];
-+
-+				memcpy(key, ctx->ipad,
-+				       crypto_ahash_blocksize(ctx->fback) / 2);
-+				memcpy(key +
-+				       crypto_ahash_blocksize(ctx->fback) / 2,
-+				       ctx->opad,
-+				       crypto_ahash_blocksize(ctx->fback) / 2);
-+				ret = crypto_ahash_setkey(ctx->fback, key,
-+					crypto_ahash_blocksize(ctx->fback));
-+				memzero_explicit(key,
-+					crypto_ahash_blocksize(ctx->fback));
-+				ctx->fb_do_setkey = false;
-+			}
-+			ret = ret ?: crypto_ahash_init(subreq);
-+			ctx->fb_init_done = true;
-+		}
-+	}
-+	return ret;
-+}
-+
-+static int safexcel_sha3_update(struct ahash_request *req)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct ahash_request *subreq = ahash_request_ctx(req);
-+
-+	ctx->do_fallback = true;
-+	return safexcel_sha3_fbcheck(req) ?: crypto_ahash_update(subreq);
-+}
-+
-+static int safexcel_sha3_final(struct ahash_request *req)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct ahash_request *subreq = ahash_request_ctx(req);
-+
-+	ctx->do_fallback = true;
-+	return safexcel_sha3_fbcheck(req) ?: crypto_ahash_final(subreq);
-+}
-+
-+static int safexcel_sha3_finup(struct ahash_request *req)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct ahash_request *subreq = ahash_request_ctx(req);
-+
-+	ctx->do_fallback |= !req->nbytes;
-+	if (ctx->do_fallback)
-+		/* Update or ex/import happened or len 0, cannot use the HW */
-+		return safexcel_sha3_fbcheck(req) ?:
-+		       crypto_ahash_finup(subreq);
-+	else
-+		return safexcel_ahash_finup(req);
-+}
-+
-+static int safexcel_sha3_digest_fallback(struct ahash_request *req)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct ahash_request *subreq = ahash_request_ctx(req);
-+
-+	ctx->do_fallback = true;
-+	ctx->fb_init_done = false;
-+	return safexcel_sha3_fbcheck(req) ?: crypto_ahash_finup(subreq);
-+}
-+
-+static int safexcel_sha3_224_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_sha3_224_init(req) ?: safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length hash, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+static int safexcel_sha3_export(struct ahash_request *req, void *out)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct ahash_request *subreq = ahash_request_ctx(req);
-+
-+	ctx->do_fallback = true;
-+	return safexcel_sha3_fbcheck(req) ?: crypto_ahash_export(subreq, out);
-+}
-+
-+static int safexcel_sha3_import(struct ahash_request *req, const void *in)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(req);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct ahash_request *subreq = ahash_request_ctx(req);
-+
-+	ctx->do_fallback = true;
-+	return safexcel_sha3_fbcheck(req) ?: crypto_ahash_import(subreq, in);
-+	// return safexcel_ahash_import(req, in);
-+}
-+
-+static int safexcel_sha3_cra_init(struct crypto_tfm *tfm)
-+{
-+	struct crypto_ahash *ahash = __crypto_ahash_cast(tfm);
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	safexcel_ahash_cra_init(tfm);
-+
-+	/* Allocate fallback implementation */
-+	ctx->fback = crypto_alloc_ahash(crypto_tfm_alg_name(tfm), 0,
-+					CRYPTO_ALG_ASYNC |
-+					CRYPTO_ALG_NEED_FALLBACK);
-+	if (IS_ERR(ctx->fback))
-+		return PTR_ERR(ctx->fback);
-+
-+	/* Update statesize from fallback algorithm! */
-+	crypto_hash_alg_common(ahash)->statesize =
-+		crypto_ahash_statesize(ctx->fback);
-+	crypto_ahash_set_reqsize(ahash, max(sizeof(struct safexcel_ahash_req),
-+					    sizeof(struct ahash_request) +
-+					    crypto_ahash_reqsize(ctx->fback)));
-+	return 0;
-+}
-+
-+static void safexcel_sha3_cra_exit(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	crypto_free_ahash(ctx->fback);
-+	safexcel_ahash_cra_exit(tfm);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_sha3_224 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_sha3_224_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_sha3_224_digest,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_224_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "sha3-224",
-+				.cra_driver_name = "safexcel-sha3-224",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_224_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_sha3_cra_init,
-+				.cra_exit = safexcel_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_sha3_256_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_256;
-+	req->digest = CONTEXT_CONTROL_DIGEST_INITIAL;
-+	req->state_sz = SHA3_256_DIGEST_SIZE;
-+	req->digest_sz = SHA3_256_DIGEST_SIZE;
-+	req->block_sz = SHA3_256_BLOCK_SIZE;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_sha3_256_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_sha3_256_init(req) ?: safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length hash, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_sha3_256 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_sha3_256_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_sha3_256_digest,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_256_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "sha3-256",
-+				.cra_driver_name = "safexcel-sha3-256",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_256_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_sha3_cra_init,
-+				.cra_exit = safexcel_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_sha3_384_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_384;
-+	req->digest = CONTEXT_CONTROL_DIGEST_INITIAL;
-+	req->state_sz = SHA3_384_DIGEST_SIZE;
-+	req->digest_sz = SHA3_384_DIGEST_SIZE;
-+	req->block_sz = SHA3_384_BLOCK_SIZE;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_sha3_384_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_sha3_384_init(req) ?: safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length hash, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_sha3_384 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_sha3_384_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_sha3_384_digest,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_384_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "sha3-384",
-+				.cra_driver_name = "safexcel-sha3-384",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_384_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_sha3_cra_init,
-+				.cra_exit = safexcel_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_sha3_512_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_512;
-+	req->digest = CONTEXT_CONTROL_DIGEST_INITIAL;
-+	req->state_sz = SHA3_512_DIGEST_SIZE;
-+	req->digest_sz = SHA3_512_DIGEST_SIZE;
-+	req->block_sz = SHA3_512_BLOCK_SIZE;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_sha3_512_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_sha3_512_init(req) ?: safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length hash, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+struct safexcel_alg_template safexcel_alg_sha3_512 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_sha3_512_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_sha3_512_digest,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_512_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "sha3-512",
-+				.cra_driver_name = "safexcel-sha3-512",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_512_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_sha3_cra_init,
-+				.cra_exit = safexcel_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_hmac_sha3_cra_init(struct crypto_tfm *tfm, const char *alg)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(tfm);
-+	int ret;
-+
-+	ret = safexcel_sha3_cra_init(tfm);
-+	if (ret)
-+		return ret;
-+
-+	/* Allocate precalc basic digest implementation */
-+	ctx->shpre = crypto_alloc_shash(alg, 0, CRYPTO_ALG_NEED_FALLBACK);
-+	if (IS_ERR(ctx->shpre))
-+		return PTR_ERR(ctx->shpre);
-+
-+	ctx->shdesc = kmalloc(sizeof(*ctx->shdesc) +
-+			      crypto_shash_descsize(ctx->shpre), GFP_KERNEL);
-+	if (!ctx->shdesc) {
-+		crypto_free_shash(ctx->shpre);
-+		return -ENOMEM;
-+	}
-+	ctx->shdesc->tfm = ctx->shpre;
-+	return 0;
-+}
-+
-+static void safexcel_hmac_sha3_cra_exit(struct crypto_tfm *tfm)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_tfm_ctx(tfm);
-+
-+	crypto_free_ahash(ctx->fback);
-+	crypto_free_shash(ctx->shpre);
-+	kfree(ctx->shdesc);
-+	safexcel_ahash_cra_exit(tfm);
-+}
-+
-+static int safexcel_hmac_sha3_setkey(struct crypto_ahash *tfm, const u8 *key,
-+				     unsigned int keylen)
-+{
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	int ret = 0;
-+
-+	if (keylen > crypto_ahash_blocksize(tfm)) {
-+		/*
-+		 * If the key is larger than the blocksize, then hash it
-+		 * first using our fallback cipher
-+		 */
-+		ret = crypto_shash_digest(ctx->shdesc, key, keylen,
-+					  (u8 *)ctx->ipad);
-+		keylen = crypto_shash_digestsize(ctx->shpre);
-+
-+		/*
-+		 * If the digest is larger than half the blocksize, we need to
-+		 * move the rest to opad due to the way our HMAC infra works.
-+		 */
-+		if (keylen > crypto_ahash_blocksize(tfm) / 2)
-+			/* Buffers overlap, need to use memmove iso memcpy! */
-+			memmove(ctx->opad,
-+				(u8 *)ctx->ipad +
-+					crypto_ahash_blocksize(tfm) / 2,
-+				keylen - crypto_ahash_blocksize(tfm) / 2);
-+	} else {
-+		/*
-+		 * Copy the key to our ipad & opad buffers
-+		 * Note that ipad and opad each contain one half of the key,
-+		 * to match the existing HMAC driver infrastructure.
-+		 */
-+		if (keylen <= crypto_ahash_blocksize(tfm) / 2) {
-+			memcpy(ctx->ipad, key, keylen);
-+		} else {
-+			memcpy(ctx->ipad, key,
-+			       crypto_ahash_blocksize(tfm) / 2);
-+			memcpy(ctx->opad,
-+			       key + crypto_ahash_blocksize(tfm) / 2,
-+			       keylen - crypto_ahash_blocksize(tfm) / 2);
-+		}
-+	}
-+
-+	/* Pad key with zeroes */
-+	if (keylen <= crypto_ahash_blocksize(tfm) / 2) {
-+		memset((u8 *)ctx->ipad + keylen, 0,
-+		       crypto_ahash_blocksize(tfm) / 2 - keylen);
-+		memset(ctx->opad, 0, crypto_ahash_blocksize(tfm) / 2);
-+	} else {
-+		memset((u8 *)ctx->opad + keylen -
-+		       crypto_ahash_blocksize(tfm) / 2, 0,
-+		       crypto_ahash_blocksize(tfm) - keylen);
-+	}
-+
-+	/* If doing fallback, still need to set the new key! */
-+	ctx->fb_do_setkey = true;
-+	return ret;
-+}
-+
-+static int safexcel_hmac_sha3_224_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	/* Copy (half of) the key */
-+	memcpy(req->state, ctx->ipad, SHA3_224_BLOCK_SIZE / 2);
-+	/* Start of HMAC should have len == processed == blocksize */
-+	req->len	= SHA3_224_BLOCK_SIZE;
-+	req->processed	= SHA3_224_BLOCK_SIZE;
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_224;
-+	req->digest = CONTEXT_CONTROL_DIGEST_HMAC;
-+	req->state_sz = SHA3_224_BLOCK_SIZE / 2;
-+	req->digest_sz = SHA3_224_DIGEST_SIZE;
-+	req->block_sz = SHA3_224_BLOCK_SIZE;
-+	req->hmac = true;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_hmac_sha3_224_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_hmac_sha3_224_init(req) ?:
-+		       safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length HMAC, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+static int safexcel_hmac_sha3_224_cra_init(struct crypto_tfm *tfm)
-+{
-+	return safexcel_hmac_sha3_cra_init(tfm, "sha3-224");
-+}
-+
-+struct safexcel_alg_template safexcel_alg_hmac_sha3_224 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_hmac_sha3_224_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_hmac_sha3_224_digest,
-+		.setkey = safexcel_hmac_sha3_setkey,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_224_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "hmac(sha3-224)",
-+				.cra_driver_name = "safexcel-hmac-sha3-224",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_224_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_hmac_sha3_224_cra_init,
-+				.cra_exit = safexcel_hmac_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_hmac_sha3_256_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	/* Copy (half of) the key */
-+	memcpy(req->state, ctx->ipad, SHA3_256_BLOCK_SIZE / 2);
-+	/* Start of HMAC should have len == processed == blocksize */
-+	req->len	= SHA3_256_BLOCK_SIZE;
-+	req->processed	= SHA3_256_BLOCK_SIZE;
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_256;
-+	req->digest = CONTEXT_CONTROL_DIGEST_HMAC;
-+	req->state_sz = SHA3_256_BLOCK_SIZE / 2;
-+	req->digest_sz = SHA3_256_DIGEST_SIZE;
-+	req->block_sz = SHA3_256_BLOCK_SIZE;
-+	req->hmac = true;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_hmac_sha3_256_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_hmac_sha3_256_init(req) ?:
-+		       safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length HMAC, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+static int safexcel_hmac_sha3_256_cra_init(struct crypto_tfm *tfm)
-+{
-+	return safexcel_hmac_sha3_cra_init(tfm, "sha3-256");
-+}
-+
-+struct safexcel_alg_template safexcel_alg_hmac_sha3_256 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_hmac_sha3_256_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_hmac_sha3_256_digest,
-+		.setkey = safexcel_hmac_sha3_setkey,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_256_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "hmac(sha3-256)",
-+				.cra_driver_name = "safexcel-hmac-sha3-256",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_256_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_hmac_sha3_256_cra_init,
-+				.cra_exit = safexcel_hmac_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_hmac_sha3_384_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	/* Copy (half of) the key */
-+	memcpy(req->state, ctx->ipad, SHA3_384_BLOCK_SIZE / 2);
-+	/* Start of HMAC should have len == processed == blocksize */
-+	req->len	= SHA3_384_BLOCK_SIZE;
-+	req->processed	= SHA3_384_BLOCK_SIZE;
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_384;
-+	req->digest = CONTEXT_CONTROL_DIGEST_HMAC;
-+	req->state_sz = SHA3_384_BLOCK_SIZE / 2;
-+	req->digest_sz = SHA3_384_DIGEST_SIZE;
-+	req->block_sz = SHA3_384_BLOCK_SIZE;
-+	req->hmac = true;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_hmac_sha3_384_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_hmac_sha3_384_init(req) ?:
-+		       safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length HMAC, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+static int safexcel_hmac_sha3_384_cra_init(struct crypto_tfm *tfm)
-+{
-+	return safexcel_hmac_sha3_cra_init(tfm, "sha3-384");
-+}
-+
-+struct safexcel_alg_template safexcel_alg_hmac_sha3_384 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_hmac_sha3_384_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_hmac_sha3_384_digest,
-+		.setkey = safexcel_hmac_sha3_setkey,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_384_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "hmac(sha3-384)",
-+				.cra_driver_name = "safexcel-hmac-sha3-384",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_384_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_hmac_sha3_384_cra_init,
-+				.cra_exit = safexcel_hmac_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
-+	},
-+};
-+
-+static int safexcel_hmac_sha3_512_init(struct ahash_request *areq)
-+{
-+	struct crypto_ahash *tfm = crypto_ahash_reqtfm(areq);
-+	struct safexcel_ahash_ctx *ctx = crypto_ahash_ctx(tfm);
-+	struct safexcel_ahash_req *req = ahash_request_ctx(areq);
-+
-+	memset(req, 0, sizeof(*req));
-+
-+	/* Copy (half of) the key */
-+	memcpy(req->state, ctx->ipad, SHA3_512_BLOCK_SIZE / 2);
-+	/* Start of HMAC should have len == processed == blocksize */
-+	req->len	= SHA3_512_BLOCK_SIZE;
-+	req->processed	= SHA3_512_BLOCK_SIZE;
-+	ctx->alg = CONTEXT_CONTROL_CRYPTO_ALG_SHA3_512;
-+	req->digest = CONTEXT_CONTROL_DIGEST_HMAC;
-+	req->state_sz = SHA3_512_BLOCK_SIZE / 2;
-+	req->digest_sz = SHA3_512_DIGEST_SIZE;
-+	req->block_sz = SHA3_512_BLOCK_SIZE;
-+	req->hmac = true;
-+	ctx->do_fallback = false;
-+	ctx->fb_init_done = false;
-+	return 0;
-+}
-+
-+static int safexcel_hmac_sha3_512_digest(struct ahash_request *req)
-+{
-+	if (req->nbytes)
-+		return safexcel_hmac_sha3_512_init(req) ?:
-+		       safexcel_ahash_finup(req);
-+
-+	/* HW cannot do zero length HMAC, use fallback instead */
-+	return safexcel_sha3_digest_fallback(req);
-+}
-+
-+static int safexcel_hmac_sha3_512_cra_init(struct crypto_tfm *tfm)
-+{
-+	return safexcel_hmac_sha3_cra_init(tfm, "sha3-512");
-+}
-+struct safexcel_alg_template safexcel_alg_hmac_sha3_512 = {
-+	.type = SAFEXCEL_ALG_TYPE_AHASH,
-+	.algo_mask = SAFEXCEL_ALG_SHA3,
-+	.alg.ahash = {
-+		.init = safexcel_hmac_sha3_512_init,
-+		.update = safexcel_sha3_update,
-+		.final = safexcel_sha3_final,
-+		.finup = safexcel_sha3_finup,
-+		.digest = safexcel_hmac_sha3_512_digest,
-+		.setkey = safexcel_hmac_sha3_setkey,
-+		.export = safexcel_sha3_export,
-+		.import = safexcel_sha3_import,
-+		.halg = {
-+			.digestsize = SHA3_512_DIGEST_SIZE,
-+			.statesize = sizeof(struct safexcel_ahash_export_state),
-+			.base = {
-+				.cra_name = "hmac(sha3-512)",
-+				.cra_driver_name = "safexcel-hmac-sha3-512",
-+				.cra_priority = SAFEXCEL_CRA_PRIORITY,
-+				.cra_flags = CRYPTO_ALG_ASYNC |
-+					     CRYPTO_ALG_KERN_DRIVER_ONLY |
-+					     CRYPTO_ALG_NEED_FALLBACK,
-+				.cra_blocksize = SHA3_512_BLOCK_SIZE,
-+				.cra_ctxsize = sizeof(struct safexcel_ahash_ctx),
-+				.cra_init = safexcel_hmac_sha3_512_cra_init,
-+				.cra_exit = safexcel_hmac_sha3_cra_exit,
-+				.cra_module = THIS_MODULE,
-+			},
-+		},
- 	},
- };
---- a/drivers/crypto/inside-secure/safexcel_ring.c
-+++ b/drivers/crypto/inside-secure/safexcel_ring.c
-@@ -14,7 +14,12 @@ int safexcel_init_ring_descriptors(struc
- 				   struct safexcel_desc_ring *cdr,
- 				   struct safexcel_desc_ring *rdr)
- {
--	cdr->offset = sizeof(u32) * priv->config.cd_offset;
-+	int i;
-+	struct safexcel_command_desc *cdesc;
-+	dma_addr_t atok;
-+
-+	/* Actual command descriptor ring */
-+	cdr->offset = priv->config.cd_offset;
- 	cdr->base = dmam_alloc_coherent(priv->dev,
- 					cdr->offset * EIP197_DEFAULT_RING_SIZE,
- 					&cdr->base_dma, GFP_KERNEL);
-@@ -24,7 +29,34 @@ int safexcel_init_ring_descriptors(struc
- 	cdr->base_end = cdr->base + cdr->offset * (EIP197_DEFAULT_RING_SIZE - 1);
- 	cdr->read = cdr->base;
- 
--	rdr->offset = sizeof(u32) * priv->config.rd_offset;
-+	/* Command descriptor shadow ring for storing additional token data */
-+	cdr->shoffset = priv->config.cdsh_offset;
-+	cdr->shbase = dmam_alloc_coherent(priv->dev,
-+					  cdr->shoffset *
-+					  EIP197_DEFAULT_RING_SIZE,
-+					  &cdr->shbase_dma, GFP_KERNEL);
-+	if (!cdr->shbase)
-+		return -ENOMEM;
-+	cdr->shwrite = cdr->shbase;
-+	cdr->shbase_end = cdr->shbase + cdr->shoffset *
-+					(EIP197_DEFAULT_RING_SIZE - 1);
-+
-+	/*
-+	 * Populate command descriptors with physical pointers to shadow descs.
-+	 * Note that we only need to do this once if we don't overwrite them.
-+	 */
-+	cdesc = cdr->base;
-+	atok = cdr->shbase_dma;
-+	for (i = 0; i < EIP197_DEFAULT_RING_SIZE; i++) {
-+		cdesc->atok_lo = lower_32_bits(atok);
-+		cdesc->atok_hi = upper_32_bits(atok);
-+		cdesc = (void *)cdesc + cdr->offset;
-+		atok += cdr->shoffset;
-+	}
-+
-+	rdr->offset = priv->config.rd_offset;
-+	/* Use shoffset for result token offset here */
-+	rdr->shoffset = priv->config.res_offset;
- 	rdr->base = dmam_alloc_coherent(priv->dev,
- 					rdr->offset * EIP197_DEFAULT_RING_SIZE,
- 					&rdr->base_dma, GFP_KERNEL);
-@@ -42,11 +74,40 @@ inline int safexcel_select_ring(struct s
- 	return (atomic_inc_return(&priv->ring_used) % priv->config.rings);
- }
- 
--static void *safexcel_ring_next_wptr(struct safexcel_crypto_priv *priv,
--				     struct safexcel_desc_ring *ring)
-+static void *safexcel_ring_next_cwptr(struct safexcel_crypto_priv *priv,
-+				     struct safexcel_desc_ring *ring,
-+				     bool first,
-+				     struct safexcel_token **atoken)
- {
- 	void *ptr = ring->write;
- 
-+	if (first)
-+		*atoken = ring->shwrite;
-+
-+	if ((ring->write == ring->read - ring->offset) ||
-+	    (ring->read == ring->base && ring->write == ring->base_end))
-+		return ERR_PTR(-ENOMEM);
-+
-+	if (ring->write == ring->base_end) {
-+		ring->write = ring->base;
-+		ring->shwrite = ring->shbase;
-+	} else {
-+		ring->write += ring->offset;
-+		ring->shwrite += ring->shoffset;
-+	}
-+
-+	return ptr;
-+}
-+
-+static void *safexcel_ring_next_rwptr(struct safexcel_crypto_priv *priv,
-+				     struct safexcel_desc_ring *ring,
-+				     struct result_data_desc **rtoken)
-+{
-+	void *ptr = ring->write;
-+
-+	/* Result token at relative offset shoffset */
-+	*rtoken = ring->write + ring->shoffset;
-+
- 	if ((ring->write == ring->read - ring->offset) ||
- 	    (ring->read == ring->base && ring->write == ring->base_end))
- 		return ERR_PTR(-ENOMEM);
-@@ -106,10 +167,13 @@ void safexcel_ring_rollback_wptr(struct
- 	if (ring->write == ring->read)
- 		return;
- 
--	if (ring->write == ring->base)
-+	if (ring->write == ring->base) {
- 		ring->write = ring->base_end;
--	else
-+		ring->shwrite = ring->shbase_end;
-+	} else {
- 		ring->write -= ring->offset;
-+		ring->shwrite -= ring->shoffset;
-+	}
- }
- 
- struct safexcel_command_desc *safexcel_add_cdesc(struct safexcel_crypto_priv *priv,
-@@ -117,26 +181,26 @@ struct safexcel_command_desc *safexcel_a
- 						 bool first, bool last,
- 						 dma_addr_t data, u32 data_len,
- 						 u32 full_data_len,
--						 dma_addr_t context) {
-+						 dma_addr_t context,
-+						 struct safexcel_token **atoken)
-+{
- 	struct safexcel_command_desc *cdesc;
--	int i;
- 
--	cdesc = safexcel_ring_next_wptr(priv, &priv->ring[ring_id].cdr);
-+	cdesc = safexcel_ring_next_cwptr(priv, &priv->ring[ring_id].cdr,
-+					 first, atoken);
- 	if (IS_ERR(cdesc))
- 		return cdesc;
- 
--	memset(cdesc, 0, sizeof(struct safexcel_command_desc));
--
--	cdesc->first_seg = first;
--	cdesc->last_seg = last;
- 	cdesc->particle_size = data_len;
-+	cdesc->rsvd0 = 0;
-+	cdesc->last_seg = last;
-+	cdesc->first_seg = first;
-+	cdesc->additional_cdata_size = 0;
-+	cdesc->rsvd1 = 0;
- 	cdesc->data_lo = lower_32_bits(data);
- 	cdesc->data_hi = upper_32_bits(data);
- 
--	if (first && context) {
--		struct safexcel_token *token =
--			(struct safexcel_token *)cdesc->control_data.token;
--
-+	if (first) {
- 		/*
- 		 * Note that the length here MUST be >0 or else the EIP(1)97
- 		 * may hang. Newer EIP197 firmware actually incorporates this
-@@ -146,20 +210,12 @@ struct safexcel_command_desc *safexcel_a
- 		cdesc->control_data.packet_length = full_data_len ?: 1;
- 		cdesc->control_data.options = EIP197_OPTION_MAGIC_VALUE |
- 					      EIP197_OPTION_64BIT_CTX |
--					      EIP197_OPTION_CTX_CTRL_IN_CMD;
--		cdesc->control_data.context_lo =
--			(lower_32_bits(context) & GENMASK(31, 2)) >> 2;
-+					      EIP197_OPTION_CTX_CTRL_IN_CMD |
-+					      EIP197_OPTION_RC_AUTO;
-+		cdesc->control_data.type = EIP197_TYPE_BCLA;
-+		cdesc->control_data.context_lo = lower_32_bits(context) |
-+						 EIP197_CONTEXT_SMALL;
- 		cdesc->control_data.context_hi = upper_32_bits(context);
--
--		if (priv->version == EIP197B_MRVL ||
--		    priv->version == EIP197D_MRVL)
--			cdesc->control_data.options |= EIP197_OPTION_RC_AUTO;
--
--		/* TODO: large xform HMAC with SHA-384/512 uses refresh = 3 */
--		cdesc->control_data.refresh = 2;
--
--		for (i = 0; i < EIP197_MAX_TOKENS; i++)
--			eip197_noop_token(&token[i]);
- 	}
- 
- 	return cdesc;
-@@ -171,18 +227,27 @@ struct safexcel_result_desc *safexcel_ad
- 						dma_addr_t data, u32 len)
- {
- 	struct safexcel_result_desc *rdesc;
-+	struct result_data_desc *rtoken;
- 
--	rdesc = safexcel_ring_next_wptr(priv, &priv->ring[ring_id].rdr);
-+	rdesc = safexcel_ring_next_rwptr(priv, &priv->ring[ring_id].rdr,
-+					 &rtoken);
- 	if (IS_ERR(rdesc))
- 		return rdesc;
- 
--	memset(rdesc, 0, sizeof(struct safexcel_result_desc));
--
--	rdesc->first_seg = first;
--	rdesc->last_seg = last;
- 	rdesc->particle_size = len;
-+	rdesc->rsvd0 = 0;
-+	rdesc->descriptor_overflow = 0;
-+	rdesc->buffer_overflow = 0;
-+	rdesc->last_seg = last;
-+	rdesc->first_seg = first;
-+	rdesc->result_size = EIP197_RD64_RESULT_SIZE;
-+	rdesc->rsvd1 = 0;
- 	rdesc->data_lo = lower_32_bits(data);
- 	rdesc->data_hi = upper_32_bits(data);
- 
-+	/* Clear length & error code in result token */
-+	rtoken->packet_length = 0;
-+	rtoken->error_code = 0;
-+
- 	return rdesc;
- }
diff --git a/target/linux/mediatek/patches-5.4/0501-crypto-add-eip97-inside-secure-support.patch b/target/linux/mediatek/patches-5.4/0501-crypto-add-eip97-inside-secure-support.patch
deleted file mode 100644
index 3eda4f291a..0000000000
--- a/target/linux/mediatek/patches-5.4/0501-crypto-add-eip97-inside-secure-support.patch
+++ /dev/null
@@ -1,27 +0,0 @@
---- a/drivers/crypto/inside-secure/safexcel.c
-+++ b/drivers/crypto/inside-secure/safexcel.c
-@@ -595,6 +595,14 @@ static int safexcel_hw_init(struct safex
- 		val |= EIP197_MST_CTRL_TX_MAX_CMD(5);
- 		writel(val, EIP197_HIA_AIC(priv) + EIP197_HIA_MST_CTRL);
- 	}
-+	/*
-+	 * Set maximum number of TX commands to 2^4 = 16 for EIP97 HW2.1/HW2.3
-+	 */
-+	else {
-+		val = 0;
-+		val |= EIP97_MST_CTRL_TX_MAX_CMD(4);
-+		writel(val, EIP197_HIA_AIC(priv) + EIP197_HIA_MST_CTRL);
-+	}
- 
- 	/* Configure wr/rd cache values */
- 	writel(EIP197_MST_CTRL_RD_CACHE(RD_CACHE_4BITS) |
---- a/drivers/crypto/inside-secure/safexcel.h
-+++ b/drivers/crypto/inside-secure/safexcel.h
-@@ -306,6 +306,7 @@
- #define EIP197_MST_CTRL_RD_CACHE(n)		(((n) & 0xf) << 0)
- #define EIP197_MST_CTRL_WD_CACHE(n)		(((n) & 0xf) << 4)
- #define EIP197_MST_CTRL_TX_MAX_CMD(n)		(((n) & 0xf) << 20)
-+#define EIP97_MST_CTRL_TX_MAX_CMD(n)		(((n) & 0xf) << 4)
- #define EIP197_MST_CTRL_BYTE_SWAP		BIT(24)
- #define EIP197_MST_CTRL_NO_BYTE_SWAP		BIT(25)
- #define EIP197_MST_CTRL_BYTE_SWAP_BITS          GENMASK(25, 24)
diff --git a/target/linux/mediatek/patches-5.4/0502-dts-mt7623-eip97-inside-secure-support.patch b/target/linux/mediatek/patches-5.4/0502-dts-mt7623-eip97-inside-secure-support.patch
deleted file mode 100644
index 06077fb984..0000000000
--- a/target/linux/mediatek/patches-5.4/0502-dts-mt7623-eip97-inside-secure-support.patch
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/arch/arm/boot/dts/mt7623.dtsi
-+++ b/arch/arm/boot/dts/mt7623.dtsi
-@@ -1047,17 +1047,14 @@
- 	};
- 
- 	crypto: crypto@1b240000 {
--		compatible = "mediatek,eip97-crypto";
-+		compatible = "inside-secure,safexcel-eip97";
- 		reg = <0 0x1b240000 0 0x20000>;
- 		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_LOW>,
- 			     <GIC_SPI 83 IRQ_TYPE_LEVEL_LOW>,
- 			     <GIC_SPI 84 IRQ_TYPE_LEVEL_LOW>,
--			     <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>,
--			     <GIC_SPI 97 IRQ_TYPE_LEVEL_LOW>;
-+			     <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
-+		interrupt-names = "ring0", "ring1", "ring2", "ring3";
- 		clocks = <&ethsys CLK_ETHSYS_CRYPTO>;
--		clock-names = "cryp";
--		power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>;
--		status = "disabled";
- 	};
- 
- 	bdpsys: syscon@1c000000 {
diff --git a/target/linux/mediatek/patches-5.4/0503-crypto-fix-eip97-cache-incoherent.patch b/target/linux/mediatek/patches-5.4/0503-crypto-fix-eip97-cache-incoherent.patch
deleted file mode 100644
index 5bc0fd0b7d..0000000000
--- a/target/linux/mediatek/patches-5.4/0503-crypto-fix-eip97-cache-incoherent.patch
+++ /dev/null
@@ -1,26 +0,0 @@
---- a/drivers/crypto/inside-secure/safexcel.h
-+++ b/drivers/crypto/inside-secure/safexcel.h
-@@ -722,6 +722,9 @@ enum safexcel_eip_version {
- /* Priority we use for advertising our algorithms */
- #define SAFEXCEL_CRA_PRIORITY		300
- 
-+/* System cache line size */
-+#define SYSTEM_CACHELINE_SIZE		64
-+
- /* SM3 digest result for zero length message */
- #define EIP197_SM3_ZEROM_HASH	"\x1A\xB2\x1D\x83\x55\xCF\xA1\x7F" \
- 				"\x8E\x61\x19\x48\x31\xE8\x1A\x8F" \
---- a/drivers/crypto/inside-secure/safexcel_hash.c
-+++ b/drivers/crypto/inside-secure/safexcel_hash.c
-@@ -57,9 +57,9 @@ struct safexcel_ahash_req {
- 	u8 block_sz;    /* block size, only set once */
- 	u8 digest_sz;   /* output digest size, only set once */
- 	__le32 state[SHA3_512_BLOCK_SIZE /
--		     sizeof(__le32)] __aligned(sizeof(__le32));
-+		     sizeof(__le32)] __aligned(SYSTEM_CACHELINE_SIZE);
- 
--	u64 len;
-+	u64 len __aligned(SYSTEM_CACHELINE_SIZE);
- 	u64 processed;
- 
- 	u8 cache[HASH_CACHE_SIZE] __aligned(sizeof(u32));
diff --git a/target/linux/mediatek/patches-5.4/0600-net-phylink-propagate-resolved-link-config-via-mac_l.patch b/target/linux/mediatek/patches-5.4/0600-net-phylink-propagate-resolved-link-config-via-mac_l.patch
deleted file mode 100644
index bd854613b7..0000000000
--- a/target/linux/mediatek/patches-5.4/0600-net-phylink-propagate-resolved-link-config-via-mac_l.patch
+++ /dev/null
@@ -1,246 +0,0 @@
-From: Russell King <rmk+kernel@armlinux.org.uk>
-Date: Wed, 26 Feb 2020 10:23:41 +0000
-Subject: [PATCH] net: phylink: propagate resolved link config via
- mac_link_up()
-
-Propagate the resolved link parameters via the mac_link_up() call for
-MACs that do not automatically track their PCS state. We propagate the
-link parameters via function arguments so that inappropriate members
-of struct phylink_link_state can't be accessed, and creating a new
-structure just for this adds needless complexity to the API.
-
-Tested-by: Andre Przywara <andre.przywara@arm.com>
-Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
-Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
-Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
-Signed-off-by: David S. Miller <davem@davemloft.net>
----
-
---- a/Documentation/networking/sfp-phylink.rst
-+++ b/Documentation/networking/sfp-phylink.rst
-@@ -74,10 +74,13 @@ phylib to the sfp/phylink support.  Plea
- this documentation.
- 
- 1. Optionally split the network driver's phylib update function into
--   three parts dealing with link-down, link-up and reconfiguring the
--   MAC settings. This can be done as a separate preparation commit.
-+   two parts dealing with link-down and link-up. This can be done as
-+   a separate preparation commit.
- 
--   An example of this preparation can be found in git commit fc548b991fb0.
-+   An older example of this preparation can be found in git commit
-+   fc548b991fb0, although this was splitting into three parts; the
-+   link-up part now includes configuring the MAC for the link settings.
-+   Please see :c:func:`mac_link_up` for more information on this.
- 
- 2. Replace::
- 
-@@ -207,6 +210,14 @@ this documentation.
-    using. This is particularly important for in-band negotiation
-    methods such as 1000base-X and SGMII.
- 
-+   The :c:func:`mac_link_up` method is used to inform the MAC that the
-+   link has come up. The call includes the negotiation mode and interface
-+   for reference only. The finalised link parameters are also supplied
-+   (speed, duplex and flow control/pause enablement settings) which
-+   should be used to configure the MAC when the MAC and PCS are not
-+   tightly integrated, or when the settings are not coming from in-band
-+   negotiation.
-+
-    The :c:func:`mac_config` method is used to update the MAC with the
-    requested state, and must avoid unnecessarily taking the link down
-    when making changes to the MAC configuration.  This means the
---- a/drivers/net/ethernet/marvell/mvneta.c
-+++ b/drivers/net/ethernet/marvell/mvneta.c
-@@ -3655,9 +3655,11 @@ static void mvneta_mac_link_down(struct
- 	mvneta_set_eee(pp, false);
- }
- 
--static void mvneta_mac_link_up(struct phylink_config *config, unsigned int mode,
--			       phy_interface_t interface,
--			       struct phy_device *phy)
-+static void mvneta_mac_link_up(struct phylink_config *config,
-+			       struct phy_device *phy,
-+			       unsigned int mode, phy_interface_t interface,
-+			       int speed, int duplex,
-+			       bool tx_pause, bool rx_pause)
- {
- 	struct net_device *ndev = to_net_dev(config->dev);
- 	struct mvneta_port *pp = netdev_priv(ndev);
---- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
-+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
-@@ -58,8 +58,11 @@ static struct {
-  */
- static void mvpp2_mac_config(struct phylink_config *config, unsigned int mode,
- 			     const struct phylink_link_state *state);
--static void mvpp2_mac_link_up(struct phylink_config *config, unsigned int mode,
--			      phy_interface_t interface, struct phy_device *phy);
-+static void mvpp2_mac_link_up(struct phylink_config *config,
-+			      struct phy_device *phy,
-+			      unsigned int mode, phy_interface_t interface,
-+			      int speed, int duplex,
-+			      bool tx_pause, bool rx_pause);
- 
- /* Queue modes */
- #define MVPP2_QDIST_SINGLE_MODE	0
-@@ -3468,8 +3471,9 @@ static void mvpp2_start_dev(struct mvpp2
- 			.interface = port->phy_interface,
- 		};
- 		mvpp2_mac_config(&port->phylink_config, MLO_AN_INBAND, &state);
--		mvpp2_mac_link_up(&port->phylink_config, MLO_AN_INBAND,
--				  port->phy_interface, NULL);
-+		mvpp2_mac_link_up(&port->phylink_config, NULL,
-+				  MLO_AN_INBAND, port->phy_interface,
-+				  SPEED_UNKNOWN, DUPLEX_UNKNOWN, false, false);
- 	}
- 
- 	netif_tx_start_all_queues(port->dev);
-@@ -5137,8 +5141,11 @@ static void mvpp2_mac_config(struct phyl
- 	mvpp2_port_enable(port);
- }
- 
--static void mvpp2_mac_link_up(struct phylink_config *config, unsigned int mode,
--			      phy_interface_t interface, struct phy_device *phy)
-+static void mvpp2_mac_link_up(struct phylink_config *config,
-+			      struct phy_device *phy,
-+			      unsigned int mode, phy_interface_t interface,
-+			      int speed, int duplex,
-+			      bool tx_pause, bool rx_pause)
- {
- 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
- 	u32 val;
---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
-+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
-@@ -449,9 +449,10 @@ static void mtk_mac_link_down(struct phy
- 	mtk_w32(mac->hw, mcr, MTK_MAC_MCR(mac->id));
- }
- 
--static void mtk_mac_link_up(struct phylink_config *config, unsigned int mode,
--			    phy_interface_t interface,
--			    struct phy_device *phy)
-+static void mtk_mac_link_up(struct phylink_config *config,
-+			    struct phy_device *phy,
-+			    unsigned int mode, phy_interface_t interface,
-+			    int speed, int duplex, bool tx_pause, bool rx_pause)
- {
- 	struct mtk_mac *mac = container_of(config, struct mtk_mac,
- 					   phylink_config);
---- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
-+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
-@@ -925,8 +925,10 @@ static void stmmac_mac_link_down(struct
- }
- 
- static void stmmac_mac_link_up(struct phylink_config *config,
-+			       struct phy_device *phy,
- 			       unsigned int mode, phy_interface_t interface,
--			       struct phy_device *phy)
-+			       int speed, int duplex,
-+			       bool tx_pause, bool rx_pause)
- {
- 	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
- 
---- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
-+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
-@@ -1499,9 +1499,10 @@ static void axienet_mac_link_down(struct
- }
- 
- static void axienet_mac_link_up(struct phylink_config *config,
--				unsigned int mode,
--				phy_interface_t interface,
--				struct phy_device *phy)
-+				struct phy_device *phy,
-+				unsigned int mode, phy_interface_t interface,
-+				int speed, int duplex,
-+				bool tx_pause, bool rx_pause)
- {
- 	/* nothing meaningful to do */
- }
---- a/drivers/net/phy/phylink.c
-+++ b/drivers/net/phy/phylink.c
-@@ -447,8 +447,11 @@ static void phylink_mac_link_up(struct p
- 	struct net_device *ndev = pl->netdev;
- 
- 	pl->cur_interface = link_state.interface;
--	pl->ops->mac_link_up(pl->config, pl->cur_link_an_mode,
--			     pl->cur_interface, pl->phydev);
-+	pl->ops->mac_link_up(pl->config, pl->phydev,
-+			     pl->cur_link_an_mode, pl->cur_interface,
-+			     link_state.speed, link_state.duplex,
-+			     !!(link_state.pause & MLO_PAUSE_TX),
-+			     !!(link_state.pause & MLO_PAUSE_RX));
- 
- 	if (ndev)
- 		netif_carrier_on(ndev);
---- a/include/linux/phylink.h
-+++ b/include/linux/phylink.h
-@@ -91,9 +91,10 @@ struct phylink_mac_ops {
- 	void (*mac_an_restart)(struct phylink_config *config);
- 	void (*mac_link_down)(struct phylink_config *config, unsigned int mode,
- 			      phy_interface_t interface);
--	void (*mac_link_up)(struct phylink_config *config, unsigned int mode,
--			    phy_interface_t interface,
--			    struct phy_device *phy);
-+	void (*mac_link_up)(struct phylink_config *config,
-+			    struct phy_device *phy, unsigned int mode,
-+			    phy_interface_t interface, int speed, int duplex,
-+			    bool tx_pause, bool rx_pause);
- };
- 
- #if 0 /* For kernel-doc purposes only. */
-@@ -217,19 +218,34 @@ void mac_link_down(struct phylink_config
- /**
-  * mac_link_up() - allow the link to come up
-  * @config: a pointer to a &struct phylink_config.
-+ * @phy: any attached phy
-  * @mode: link autonegotiation mode
-  * @interface: link &typedef phy_interface_t mode
-- * @phy: any attached phy
-+ * @speed: link speed
-+ * @duplex: link duplex
-+ * @tx_pause: link transmit pause enablement status
-+ * @rx_pause: link receive pause enablement status
-+ *
-+ * Configure the MAC for an established link.
-+ *
-+ * @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link
-+ * settings, and should be used to configure the MAC block appropriately
-+ * where these settings are not automatically conveyed from the PCS block,
-+ * or if in-band negotiation (as defined by phylink_autoneg_inband(@mode))
-+ * is disabled.
-+ *
-+ * Note that when 802.3z in-band negotiation is in use, it is possible
-+ * that the user wishes to override the pause settings, and this should
-+ * be allowed when considering the implementation of this method.
-  *
-- * If @mode is not an in-band negotiation mode (as defined by
-- * phylink_autoneg_inband()), allow the link to come up. If @phy
-- * is non-%NULL, configure Energy Efficient Ethernet by calling
-+ * If in-band negotiation mode is disabled, allow the link to come up. If
-+ * @phy is non-%NULL, configure Energy Efficient Ethernet by calling
-  * phy_init_eee() and perform appropriate MAC configuration for EEE.
-  * Interface type selection must be done in mac_config().
-  */
--void mac_link_up(struct phylink_config *config, unsigned int mode,
--		 phy_interface_t interface,
--		 struct phy_device *phy);
-+void mac_link_up(struct phylink_config *config, struct phy_device *phy,
-+		 unsigned int mode, phy_interface_t interface,
-+		 int speed, int duplex, bool tx_pause, bool rx_pause);
- #endif
- 
- struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *,
---- a/net/dsa/port.c
-+++ b/net/dsa/port.c
-@@ -529,9 +529,11 @@ void dsa_port_phylink_mac_link_down(stru
- EXPORT_SYMBOL_GPL(dsa_port_phylink_mac_link_down);
- 
- void dsa_port_phylink_mac_link_up(struct phylink_config *config,
-+				  struct phy_device *phydev,
- 				  unsigned int mode,
- 				  phy_interface_t interface,
--				  struct phy_device *phydev)
-+				  int speed, int duplex,
-+				  bool tx_pause, bool rx_pause)
- {
- 	struct dsa_port *dp = container_of(config, struct dsa_port, pl_config);
- 	struct dsa_switch *ds = dp->ds;
diff --git a/target/linux/mediatek/patches-5.4/0601-net-dsa-propagate-resolved-link-config-via-mac_link_.patch b/target/linux/mediatek/patches-5.4/0601-net-dsa-propagate-resolved-link-config-via-mac_link_.patch
deleted file mode 100644
index 0df300b627..0000000000
--- a/target/linux/mediatek/patches-5.4/0601-net-dsa-propagate-resolved-link-config-via-mac_link_.patch
+++ /dev/null
@@ -1,143 +0,0 @@
-From: Russell King <rmk+kernel@armlinux.org.uk>
-Date: Wed, 26 Feb 2020 10:23:46 +0000
-Subject: [PATCH] net: dsa: propagate resolved link config via mac_link_up()
-
-Propagate the resolved link configuration down via DSA's
-phylink_mac_link_up() operation to allow split PCS/MAC to work.
-
-Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
-Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
-Signed-off-by: David S. Miller <davem@davemloft.net>
----
-
---- a/drivers/net/dsa/b53/b53_common.c
-+++ b/drivers/net/dsa/b53/b53_common.c
-@@ -1284,7 +1284,9 @@ EXPORT_SYMBOL(b53_phylink_mac_link_down)
- void b53_phylink_mac_link_up(struct dsa_switch *ds, int port,
- 			     unsigned int mode,
- 			     phy_interface_t interface,
--			     struct phy_device *phydev)
-+			     struct phy_device *phydev,
-+			     int speed, int duplex,
-+			     bool tx_pause, bool rx_pause)
- {
- 	struct b53_device *dev = ds->priv;
- 
---- a/drivers/net/dsa/b53/b53_priv.h
-+++ b/drivers/net/dsa/b53/b53_priv.h
-@@ -337,7 +337,9 @@ void b53_phylink_mac_link_down(struct ds
- void b53_phylink_mac_link_up(struct dsa_switch *ds, int port,
- 			     unsigned int mode,
- 			     phy_interface_t interface,
--			     struct phy_device *phydev);
-+			     struct phy_device *phydev,
-+			     int speed, int duplex,
-+			     bool tx_pause, bool rx_pause);
- int b53_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering);
- int b53_vlan_prepare(struct dsa_switch *ds, int port,
- 		     const struct switchdev_obj_port_vlan *vlan);
---- a/drivers/net/dsa/bcm_sf2.c
-+++ b/drivers/net/dsa/bcm_sf2.c
-@@ -636,7 +636,9 @@ static void bcm_sf2_sw_mac_link_down(str
- static void bcm_sf2_sw_mac_link_up(struct dsa_switch *ds, int port,
- 				   unsigned int mode,
- 				   phy_interface_t interface,
--				   struct phy_device *phydev)
-+				   struct phy_device *phydev,
-+				   int speed, int duplex,
-+				   bool tx_pause, bool rx_pause)
- {
- 	struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
- 	struct ethtool_eee *p = &priv->dev->ports[port].eee;
---- a/drivers/net/dsa/lantiq_gswip.c
-+++ b/drivers/net/dsa/lantiq_gswip.c
-@@ -1663,7 +1663,9 @@ static void gswip_phylink_mac_link_down(
- static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port,
- 				      unsigned int mode,
- 				      phy_interface_t interface,
--				      struct phy_device *phydev)
-+				      struct phy_device *phydev,
-+				      int speed, int duplex,
-+				      bool tx_pause, bool rx_pause)
- {
- 	struct gswip_priv *priv = ds->priv;
- 
---- a/drivers/net/dsa/mt7530.c
-+++ b/drivers/net/dsa/mt7530.c
-@@ -1440,7 +1440,9 @@ static void mt7530_phylink_mac_link_down
- static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
- 				       unsigned int mode,
- 				       phy_interface_t interface,
--				       struct phy_device *phydev)
-+				       struct phy_device *phydev,
-+				       int speed, int duplex,
-+				       bool tx_pause, bool rx_pause)
- {
- 	struct mt7530_priv *priv = ds->priv;
- 
---- a/drivers/net/dsa/mv88e6xxx/chip.c
-+++ b/drivers/net/dsa/mv88e6xxx/chip.c
-@@ -652,7 +652,9 @@ static void mv88e6xxx_mac_link_down(stru
- 
- static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
- 				  unsigned int mode, phy_interface_t interface,
--				  struct phy_device *phydev)
-+				  struct phy_device *phydev,
-+				  int speed, int duplex,
-+				  bool tx_pause, bool rx_pause)
- {
- 	if (mode == MLO_AN_FIXED)
- 		mv88e6xxx_mac_link_force(ds, port, LINK_FORCED_UP);
---- a/drivers/net/dsa/sja1105/sja1105_main.c
-+++ b/drivers/net/dsa/sja1105/sja1105_main.c
-@@ -831,7 +831,9 @@ static void sja1105_mac_link_down(struct
- static void sja1105_mac_link_up(struct dsa_switch *ds, int port,
- 				unsigned int mode,
- 				phy_interface_t interface,
--				struct phy_device *phydev)
-+				struct phy_device *phydev,
-+				int speed, int duplex,
-+				bool tx_pause, bool rx_pause)
- {
- 	sja1105_inhibit_tx(ds->priv, BIT(port), false);
- }
---- a/include/net/dsa.h
-+++ b/include/net/dsa.h
-@@ -406,7 +406,9 @@ struct dsa_switch_ops {
- 	void	(*phylink_mac_link_up)(struct dsa_switch *ds, int port,
- 				       unsigned int mode,
- 				       phy_interface_t interface,
--				       struct phy_device *phydev);
-+				       struct phy_device *phydev,
-+				       int speed, int duplex,
-+				       bool tx_pause, bool rx_pause);
- 	void	(*phylink_fixed_state)(struct dsa_switch *ds, int port,
- 				       struct phylink_link_state *state);
- 	/*
---- a/net/dsa/port.c
-+++ b/net/dsa/port.c
-@@ -544,7 +544,8 @@ void dsa_port_phylink_mac_link_up(struct
- 		return;
- 	}
- 
--	ds->ops->phylink_mac_link_up(ds, dp->index, mode, interface, phydev);
-+	ds->ops->phylink_mac_link_up(ds, dp->index, mode, interface, phydev,
-+				     speed, duplex, tx_pause, rx_pause);
- }
- EXPORT_SYMBOL_GPL(dsa_port_phylink_mac_link_up);
- 
---- a/net/dsa/dsa_priv.h
-+++ b/net/dsa/dsa_priv.h
-@@ -192,9 +192,11 @@ void dsa_port_phylink_mac_link_down(stru
- 				    unsigned int mode,
- 				    phy_interface_t interface);
- void dsa_port_phylink_mac_link_up(struct phylink_config *config,
-+				  struct phy_device *phydev,
- 				  unsigned int mode,
- 				  phy_interface_t interface,
--				  struct phy_device *phydev);
-+				  int speed, int duplex,
-+				  bool tx_pause, bool rx_pause);
- extern const struct phylink_mac_ops dsa_port_phylink_mac_ops;
- 
- /* slave.c */
diff --git a/target/linux/mediatek/patches-5.4/0602-net-dsa-mt7530-use-resolved-link-config-in-mac_link_.patch b/target/linux/mediatek/patches-5.4/0602-net-dsa-mt7530-use-resolved-link-config-in-mac_link_.patch
deleted file mode 100644
index 23fba85252..0000000000
--- a/target/linux/mediatek/patches-5.4/0602-net-dsa-mt7530-use-resolved-link-config-in-mac_link_.patch
+++ /dev/null
@@ -1,145 +0,0 @@
-From: =?UTF-8?q?Ren=C3=A9=20van=20Dorst?= <opensource@vdorst.com>
-Date: Fri, 27 Mar 2020 15:44:12 +0100
-Subject: [PATCH] net: dsa: mt7530: use resolved link config in mac_link_up()
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Convert the mt7530 switch driver to use the finalised link
-parameters in mac_link_up() rather than the parameters in mac_config().
-
-Signed-off-by: René van Dorst <opensource@vdorst.com>
-Tested-by: Sean Wang <sean.wang@mediatek.com>
-Signed-off-by: David S. Miller <davem@davemloft.net>
----
-
---- a/drivers/net/dsa/mt7530.c
-+++ b/drivers/net/dsa/mt7530.c
-@@ -489,17 +489,6 @@ mt7530_mib_reset(struct dsa_switch *ds)
- 	mt7530_write(priv, MT7530_MIB_CCR, CCR_MIB_ACTIVATE);
- }
- 
--static void
--mt7530_port_set_status(struct mt7530_priv *priv, int port, int enable)
--{
--	u32 mask = PMCR_TX_EN | PMCR_RX_EN | PMCR_FORCE_LNK;
--
--	if (enable)
--		mt7530_set(priv, MT7530_PMCR_P(port), mask);
--	else
--		mt7530_clear(priv, MT7530_PMCR_P(port), mask);
--}
--
- static int mt7530_phy_read(struct dsa_switch *ds, int port, int regnum)
- {
- 	struct mt7530_priv *priv = ds->priv;
-@@ -673,7 +662,7 @@ mt7530_port_enable(struct dsa_switch *ds
- 	priv->ports[port].enable = true;
- 	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
- 		   priv->ports[port].pm);
--	mt7530_port_set_status(priv, port, 0);
-+	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
- 
- 	mutex_unlock(&priv->reg_mutex);
- 
-@@ -696,7 +685,7 @@ mt7530_port_disable(struct dsa_switch *d
- 	priv->ports[port].enable = false;
- 	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
- 		   PCR_MATRIX_CLR);
--	mt7530_port_set_status(priv, port, 0);
-+	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
- 
- 	mutex_unlock(&priv->reg_mutex);
- }
-@@ -1395,8 +1384,7 @@ static void mt7530_phylink_mac_config(st
- 
- 	mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
- 	mcr_new = mcr_cur;
--	mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
--		     PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
-+	mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
- 	mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
- 		   PMCR_BACKPR_EN | PMCR_FORCE_MODE;
- 
-@@ -1404,26 +1392,6 @@ static void mt7530_phylink_mac_config(st
- 	if (port == 5 && dsa_is_user_port(ds, 5))
- 		mcr_new |= PMCR_EXT_PHY;
- 
--	switch (state->speed) {
--	case SPEED_1000:
--		mcr_new |= PMCR_FORCE_SPEED_1000;
--		if (priv->eee_enable & BIT(port))
--			mcr_new |= PMCR_FORCE_EEE1G;
--		break;
--	case SPEED_100:
--		mcr_new |= PMCR_FORCE_SPEED_100;
--		if (priv->eee_enable & BIT(port))
--			mcr_new |= PMCR_FORCE_EEE100;
--		break;
--	}
--	if (state->duplex == DUPLEX_FULL) {
--		mcr_new |= PMCR_FORCE_FDX;
--		if (state->pause & MLO_PAUSE_TX)
--			mcr_new |= PMCR_TX_FC_EN;
--		if (state->pause & MLO_PAUSE_RX)
--			mcr_new |= PMCR_RX_FC_EN;
--	}
--
- 	if (mcr_new != mcr_cur)
- 		mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
- }
-@@ -1434,7 +1402,7 @@ static void mt7530_phylink_mac_link_down
- {
- 	struct mt7530_priv *priv = ds->priv;
- 
--	mt7530_port_set_status(priv, port, 0);
-+	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
- }
- 
- static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
-@@ -1445,8 +1413,31 @@ static void mt7530_phylink_mac_link_up(s
- 				       bool tx_pause, bool rx_pause)
- {
- 	struct mt7530_priv *priv = ds->priv;
-+	u32 mcr;
-+
-+	mcr = PMCR_RX_EN | PMCR_TX_EN | PMCR_FORCE_LNK;
-+
-+	switch (speed) {
-+	case SPEED_1000:
-+		mcr |= PMCR_FORCE_SPEED_1000;
-+		if (priv->eee_enable & BIT(port))
-+			mcr_new |= PMCR_FORCE_EEE1G;
-+		break;
-+	case SPEED_100:
-+		mcr |= PMCR_FORCE_SPEED_100;
-+		if (priv->eee_enable & BIT(port))
-+			mcr_new |= PMCR_FORCE_EEE100;
-+		break;
-+	}
-+	if (duplex == DUPLEX_FULL) {
-+		mcr |= PMCR_FORCE_FDX;
-+		if (tx_pause)
-+			mcr |= PMCR_TX_FC_EN;
-+		if (rx_pause)
-+			mcr |= PMCR_RX_FC_EN;
-+	}
- 
--	mt7530_port_set_status(priv, port, 1);
-+	mt7530_set(priv, MT7530_PMCR_P(port), mcr);
- }
- 
- static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
---- a/drivers/net/dsa/mt7530.h
-+++ b/drivers/net/dsa/mt7530.h
-@@ -222,6 +222,10 @@ enum mt7530_vlan_port_attr {
- #define  PMCR_FORCE_LNK			BIT(0)
- #define  PMCR_SPEED_MASK		(PMCR_FORCE_SPEED_100 | \
- 					 PMCR_FORCE_SPEED_1000)
-+#define  PMCR_LINK_SETTINGS_MASK	(PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
-+					 PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
-+					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
-+					 PMCR_FORCE_FDX | PMCR_FORCE_LNK)
- 
- #define MT7530_PMSR_P(x)		(0x3008 + (x) * 0x100)
- #define  PMSR_EEE1G			BIT(7)
diff --git a/target/linux/mediatek/patches-5.4/0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch b/target/linux/mediatek/patches-5.4/0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch
deleted file mode 100644
index 718ed8ea2d..0000000000
--- a/target/linux/mediatek/patches-5.4/0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch
+++ /dev/null
@@ -1,458 +0,0 @@
-From: Landen Chao <landen.chao@mediatek.com>
-Date: Fri, 4 Sep 2020 22:21:57 +0800
-Subject: [PATCH] net: dsa: mt7530: Extend device data ready for adding a
- new hardware
-
-Add a structure holding required operations for each device such as device
-initialization, PHY port read or write, a checker whether PHY interface is
-supported on a certain port, MAC port setup for either bus pad or a
-specific PHY interface.
-
-The patch is done for ready adding a new hardware MT7531, and keep the
-same setup logic of existing hardware.
-
-Signed-off-by: Landen Chao <landen.chao@mediatek.com>
-Signed-off-by: Sean Wang <sean.wang@mediatek.com>
----
-
---- a/drivers/net/dsa/mt7530.c
-+++ b/drivers/net/dsa/mt7530.c
-@@ -373,8 +373,9 @@ mt7530_fdb_write(struct mt7530_priv *pri
- 		mt7530_write(priv, MT7530_ATA1 + (i * 4), reg[i]);
- }
- 
-+/* Setup TX circuit including relevant PAD and driving */
- static int
--mt7530_pad_clk_setup(struct dsa_switch *ds, int mode)
-+mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
- {
- 	struct mt7530_priv *priv = ds->priv;
- 	u32 ncpo1, ssc_delta, trgint, i, xtal;
-@@ -388,7 +389,7 @@ mt7530_pad_clk_setup(struct dsa_switch *
- 		return -EINVAL;
- 	}
- 
--	switch (mode) {
-+	switch (interface) {
- 	case PHY_INTERFACE_MODE_RGMII:
- 		trgint = 0;
- 		/* PLL frequency: 125MHz */
-@@ -410,7 +411,8 @@ mt7530_pad_clk_setup(struct dsa_switch *
- 		}
- 		break;
- 	default:
--		dev_err(priv->dev, "xMII mode %d not supported\n", mode);
-+		dev_err(priv->dev, "xMII interface %d not supported\n",
-+			interface);
- 		return -EINVAL;
- 	}
- 
-@@ -1332,12 +1334,11 @@ mt7530_setup(struct dsa_switch *ds)
- 	return 0;
- }
- 
--static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
--				      unsigned int mode,
--				      const struct phylink_link_state *state)
-+static bool
-+mt7530_phy_mode_supported(struct dsa_switch *ds, int port,
-+			  const struct phylink_link_state *state)
- {
- 	struct mt7530_priv *priv = ds->priv;
--	u32 mcr_cur, mcr_new;
- 
- 	switch (port) {
- 	case 0: /* Internal phy */
-@@ -1346,33 +1347,114 @@ static void mt7530_phylink_mac_config(st
- 	case 3:
- 	case 4:
- 		if (state->interface != PHY_INTERFACE_MODE_GMII)
--			return;
-+			goto unsupported;
- 		break;
- 	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
--		if (priv->p5_interface == state->interface)
--			break;
- 		if (!phy_interface_mode_is_rgmii(state->interface) &&
- 		    state->interface != PHY_INTERFACE_MODE_MII &&
- 		    state->interface != PHY_INTERFACE_MODE_GMII)
--			return;
-+			goto unsupported;
-+		break;
-+	case 6: /* 1st cpu port */
-+		if (state->interface != PHY_INTERFACE_MODE_RGMII &&
-+		    state->interface != PHY_INTERFACE_MODE_TRGMII)
-+			goto unsupported;
-+		break;
-+	default:
-+		dev_err(priv->dev, "%s: unsupported port: %i\n", __func__,
-+			port);
-+		goto unsupported;
-+	}
-+
-+	return true;
-+
-+unsupported:
-+	return false;
-+}
-+
-+static bool
-+mt753x_phy_mode_supported(struct dsa_switch *ds, int port,
-+			  const struct phylink_link_state *state)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	return priv->info->phy_mode_supported(ds, port, state);
-+}
-+
-+static int
-+mt753x_pad_setup(struct dsa_switch *ds, const struct phylink_link_state *state)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	return priv->info->pad_setup(ds, state->interface);
-+}
-+
-+static int
-+mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
-+		  phy_interface_t interface)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	/* Only need to setup port5. */
-+	if (port != 5)
-+		return 0;
-+
-+	mt7530_setup_port5(priv->ds, interface);
-+
-+	return 0;
-+}
-+
-+static int
-+mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
-+		  const struct phylink_link_state *state)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	return priv->info->mac_port_config(ds, port, mode, state->interface);
-+}
-+
-+static void
-+mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
-+			  const struct phylink_link_state *state)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	u32 mcr_cur, mcr_new;
-+
-+	if (!mt753x_phy_mode_supported(ds, port, state))
-+		goto unsupported;
-+
-+	switch (port) {
-+	case 0: /* Internal phy */
-+	case 1:
-+	case 2:
-+	case 3:
-+	case 4:
-+		if (state->interface != PHY_INTERFACE_MODE_GMII)
-+			goto unsupported;
-+		break;
-+	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
-+		if (priv->p5_interface == state->interface)
-+			break;
-+
-+		if (mt753x_mac_config(ds, port, mode, state) < 0)
-+			goto unsupported;
- 
--		mt7530_setup_port5(ds, state->interface);
- 		break;
- 	case 6: /* 1st cpu port */
- 		if (priv->p6_interface == state->interface)
- 			break;
- 
--		if (state->interface != PHY_INTERFACE_MODE_RGMII &&
--		    state->interface != PHY_INTERFACE_MODE_TRGMII)
--			return;
-+		mt753x_pad_setup(ds, state);
- 
--		/* Setup TX circuit incluing relevant PAD and driving */
--		mt7530_pad_clk_setup(ds, state->interface);
-+		if (mt753x_mac_config(ds, port, mode, state) < 0)
-+			goto unsupported;
- 
- 		priv->p6_interface = state->interface;
- 		break;
- 	default:
--		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
-+unsupported:
-+		dev_err(ds->dev, "%s: unsupported %s port: %i\n",
-+			__func__, phy_modes(state->interface), port);
- 		return;
- 	}
- 
-@@ -1440,61 +1522,44 @@ static void mt7530_phylink_mac_link_up(s
- 	mt7530_set(priv, MT7530_PMCR_P(port), mcr);
- }
- 
--static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
--				    unsigned long *supported,
--				    struct phylink_link_state *state)
-+static void
-+mt7530_mac_port_validate(struct dsa_switch *ds, int port,
-+			 unsigned long *supported)
- {
-+	if (port == 5)
-+		phylink_set(supported, 1000baseX_Full);
-+}
-+
-+static void
-+mt753x_phylink_validate(struct dsa_switch *ds, int port,
-+			unsigned long *supported,
-+			struct phylink_link_state *state)
-+{
-+	struct mt7530_priv *priv = ds->priv;
- 	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
- 
--	switch (port) {
--	case 0: /* Internal phy */
--	case 1:
--	case 2:
--	case 3:
--	case 4:
--		if (state->interface != PHY_INTERFACE_MODE_NA &&
--		    state->interface != PHY_INTERFACE_MODE_GMII)
--			goto unsupported;
--		break;
--	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
--		if (state->interface != PHY_INTERFACE_MODE_NA &&
--		    !phy_interface_mode_is_rgmii(state->interface) &&
--		    state->interface != PHY_INTERFACE_MODE_MII &&
--		    state->interface != PHY_INTERFACE_MODE_GMII)
--			goto unsupported;
--		break;
--	case 6: /* 1st cpu port */
--		if (state->interface != PHY_INTERFACE_MODE_NA &&
--		    state->interface != PHY_INTERFACE_MODE_RGMII &&
--		    state->interface != PHY_INTERFACE_MODE_TRGMII)
--			goto unsupported;
--		break;
--	default:
--		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
--unsupported:
-+	if (state->interface != PHY_INTERFACE_MODE_NA &&
-+	    !mt753x_phy_mode_supported(ds, port, state)) {
- 		linkmode_zero(supported);
- 		return;
- 	}
- 
- 	phylink_set_port_modes(mask);
--	phylink_set(mask, Autoneg);
- 
--	if (state->interface == PHY_INTERFACE_MODE_TRGMII) {
--		phylink_set(mask, 1000baseT_Full);
--	} else {
-+	if (state->interface != PHY_INTERFACE_MODE_TRGMII) {
- 		phylink_set(mask, 10baseT_Half);
- 		phylink_set(mask, 10baseT_Full);
- 		phylink_set(mask, 100baseT_Half);
- 		phylink_set(mask, 100baseT_Full);
--
--		if (state->interface != PHY_INTERFACE_MODE_MII) {
--			/* This switch only supports 1G full-duplex. */
--			phylink_set(mask, 1000baseT_Full);
--			if (port == 5)
--				phylink_set(mask, 1000baseX_Full);
--		}
-+		phylink_set(mask, Autoneg);
- 	}
- 
-+	/* This switch only supports 1G full-duplex. */
-+	if (state->interface != PHY_INTERFACE_MODE_MII)
-+		phylink_set(mask, 1000baseT_Full);
-+
-+	priv->info->mac_port_validate(ds, port, mask);
-+
- 	phylink_set(mask, Pause);
- 	phylink_set(mask, Asym_Pause);
- 
-@@ -1590,12 +1655,45 @@ static int mt7530_set_mac_eee(struct dsa
- 	return 0;
- }
- 
-+static int
-+mt753x_phylink_mac_link_state(struct dsa_switch *ds, int port,
-+			      struct phylink_link_state *state)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	return priv->info->mac_port_get_state(ds, port, state);
-+}
-+
-+static int
-+mt753x_setup(struct dsa_switch *ds)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	return priv->info->sw_setup(ds);
-+}
-+
-+static int
-+mt753x_phy_read(struct dsa_switch *ds, int port, int regnum)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	return priv->info->phy_read(ds, port, regnum);
-+}
-+
-+static int
-+mt753x_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	return priv->info->phy_write(ds, port, regnum, val);
-+}
-+
- static const struct dsa_switch_ops mt7530_switch_ops = {
- 	.get_tag_protocol	= mtk_get_tag_protocol,
--	.setup			= mt7530_setup,
-+	.setup			= mt753x_setup,
- 	.get_strings		= mt7530_get_strings,
--	.phy_read		= mt7530_phy_read,
--	.phy_write		= mt7530_phy_write,
-+	.phy_read		= mt753x_phy_read,
-+	.phy_write		= mt753x_phy_write,
- 	.get_ethtool_stats	= mt7530_get_ethtool_stats,
- 	.get_sset_count		= mt7530_get_sset_count,
- 	.port_enable		= mt7530_port_enable,
-@@ -1612,18 +1710,43 @@ static const struct dsa_switch_ops mt753
- 	.port_vlan_del		= mt7530_port_vlan_del,
- 	.port_mirror_add	= mt7530_port_mirror_add,
- 	.port_mirror_del	= mt7530_port_mirror_del,
--	.phylink_validate	= mt7530_phylink_validate,
--	.phylink_mac_link_state = mt7530_phylink_mac_link_state,
--	.phylink_mac_config	= mt7530_phylink_mac_config,
-+	.phylink_validate	= mt753x_phylink_validate,
-+	.phylink_mac_link_state	= mt753x_phylink_mac_link_state,
-+	.phylink_mac_config	= mt753x_phylink_mac_config,
- 	.phylink_mac_link_down	= mt7530_phylink_mac_link_down,
- 	.phylink_mac_link_up	= mt7530_phylink_mac_link_up,
- 	.get_mac_eee		= mt7530_get_mac_eee,
- 	.set_mac_eee		= mt7530_set_mac_eee,
- };
- 
-+static const struct mt753x_info mt753x_table[] = {
-+	[ID_MT7621] = {
-+		.id = ID_MT7621,
-+		.sw_setup = mt7530_setup,
-+		.phy_read = mt7530_phy_read,
-+		.phy_write = mt7530_phy_write,
-+		.pad_setup = mt7530_pad_clk_setup,
-+		.phy_mode_supported = mt7530_phy_mode_supported,
-+		.mac_port_validate = mt7530_mac_port_validate,
-+		.mac_port_get_state = mt7530_phylink_mac_link_state,
-+		.mac_port_config = mt7530_mac_config,
-+	},
-+	[ID_MT7530] = {
-+		.id = ID_MT7530,
-+		.sw_setup = mt7530_setup,
-+		.phy_read = mt7530_phy_read,
-+		.phy_write = mt7530_phy_write,
-+		.pad_setup = mt7530_pad_clk_setup,
-+		.phy_mode_supported = mt7530_phy_mode_supported,
-+		.mac_port_validate = mt7530_mac_port_validate,
-+		.mac_port_get_state = mt7530_phylink_mac_link_state,
-+		.mac_port_config = mt7530_mac_config,
-+	},
-+};
-+
- static const struct of_device_id mt7530_of_match[] = {
--	{ .compatible = "mediatek,mt7621", .data = (void *)ID_MT7621, },
--	{ .compatible = "mediatek,mt7530", .data = (void *)ID_MT7530, },
-+	{ .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], },
-+	{ .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], },
- 	{ /* sentinel */ },
- };
- MODULE_DEVICE_TABLE(of, mt7530_of_match);
-@@ -1661,8 +1784,21 @@ mt7530_probe(struct mdio_device *mdiodev
- 	/* Get the hardware identifier from the devicetree node.
- 	 * We will need it for some of the clock and regulator setup.
- 	 */
--	priv->id = (unsigned int)(unsigned long)
--		of_device_get_match_data(&mdiodev->dev);
-+	priv->info = of_device_get_match_data(&mdiodev->dev);
-+	if (!priv->info)
-+		return -EINVAL;
-+
-+	/* Sanity check if these required device operations are filled
-+	 * properly.
-+	 */
-+	if (!priv->info->sw_setup || !priv->info->pad_setup ||
-+	    !priv->info->phy_read || !priv->info->phy_write ||
-+	    !priv->info->phy_mode_supported ||
-+	    !priv->info->mac_port_validate ||
-+	    !priv->info->mac_port_get_state || !priv->info->mac_port_config)
-+		return -EINVAL;
-+
-+	priv->id = priv->info->id;
- 
- 	if (priv->id == ID_MT7530) {
- 		priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
---- a/drivers/net/dsa/mt7530.h
-+++ b/drivers/net/dsa/mt7530.h
-@@ -11,7 +11,7 @@
- #define MT7530_NUM_FDB_RECORDS		2048
- #define MT7530_ALL_MEMBERS		0xff
- 
--enum {
-+enum mt753x_id {
- 	ID_MT7530 = 0,
- 	ID_MT7621 = 1,
- };
-@@ -451,6 +451,40 @@ static const char *p5_intf_modes(unsigne
- 	}
- }
- 
-+/* struct mt753x_info -	This is the main data structure for holding the specific
-+ *			part for each supported device
-+ * @sw_setup:		Holding the handler to a device initialization
-+ * @phy_read:		Holding the way reading PHY port
-+ * @phy_write:		Holding the way writing PHY port
-+ * @pad_setup:		Holding the way setting up the bus pad for a certain
-+ *			MAC port
-+ * @phy_mode_supported:	Check if the PHY type is being supported on a certain
-+ *			port
-+ * @mac_port_validate:	Holding the way to set addition validate type for a
-+ *			certan MAC port
-+ * @mac_port_get_state: Holding the way getting the MAC/PCS state for a certain
-+ *			MAC port
-+ * @mac_port_config:	Holding the way setting up the PHY attribute to a
-+ *			certain MAC port
-+ */
-+struct mt753x_info {
-+	enum mt753x_id id;
-+
-+	int (*sw_setup)(struct dsa_switch *ds);
-+	int (*phy_read)(struct dsa_switch *ds, int port, int regnum);
-+	int (*phy_write)(struct dsa_switch *ds, int port, int regnum, u16 val);
-+	int (*pad_setup)(struct dsa_switch *ds, phy_interface_t interface);
-+	bool (*phy_mode_supported)(struct dsa_switch *ds, int port,
-+				   const struct phylink_link_state *state);
-+	void (*mac_port_validate)(struct dsa_switch *ds, int port,
-+				  unsigned long *supported);
-+	int (*mac_port_get_state)(struct dsa_switch *ds, int port,
-+				  struct phylink_link_state *state);
-+	int (*mac_port_config)(struct dsa_switch *ds, int port,
-+			       unsigned int mode,
-+			       phy_interface_t interface);
-+};
-+
- /* struct mt7530_priv -	This is the main data structure for holding the state
-  *			of the driver
-  * @dev:		The device pointer
-@@ -476,6 +510,7 @@ struct mt7530_priv {
- 	struct regulator	*core_pwr;
- 	struct regulator	*io_pwr;
- 	struct gpio_desc	*reset;
-+	const struct mt753x_info *info;
- 	unsigned int		id;
- 	bool			mcm;
- 	phy_interface_t		p6_interface;
diff --git a/target/linux/mediatek/patches-5.4/0604-net-dsa-mt7530-Add-the-support-of-MT7531-switch.patch b/target/linux/mediatek/patches-5.4/0604-net-dsa-mt7530-Add-the-support-of-MT7531-switch.patch
deleted file mode 100644
index 8ede862204..0000000000
--- a/target/linux/mediatek/patches-5.4/0604-net-dsa-mt7530-Add-the-support-of-MT7531-switch.patch
+++ /dev/null
@@ -1,1510 +0,0 @@
-From: Landen Chao <landen.chao@mediatek.com>
-Date: Fri, 4 Sep 2020 22:21:59 +0800
-Subject: [PATCH] net: dsa: mt7530: Add the support of MT7531 switch
-
-Add new support for MT7531:
-
-MT7531 is the next generation of MT7530. It is also a 7-ports switch with
-5 giga embedded phys, 2 cpu ports, and the same MAC logic of MT7530. Cpu
-port 6 only supports SGMII interface. Cpu port 5 supports either RGMII
-or SGMII in different HW sku, but cannot be muxed to PHY of port 0/4 like
-mt7530. Due to SGMII interface support, pll, and pad setting are different
-from MT7530. This patch adds different initial setting, and SGMII phylink
-handlers of MT7531.
-
-MT7531 SGMII interface can be configured in following mode:
-- 'SGMII AN mode' with in-band negotiation capability
-    which is compatible with PHY_INTERFACE_MODE_SGMII.
-- 'SGMII force mode' without in-band negotiation
-    which is compatible with 10B/8B encoding of
-    PHY_INTERFACE_MODE_1000BASEX with fixed full-duplex and fixed pause.
-- 2.5 times faster clocked 'SGMII force mode' without in-band negotiation
-    which is compatible with 10B/8B encoding of
-    PHY_INTERFACE_MODE_2500BASEX with fixed full-duplex and fixed pause.
-
-Signed-off-by: Landen Chao <landen.chao@mediatek.com>
-Signed-off-by: Sean Wang <sean.wang@mediatek.com>
----
-
---- a/drivers/net/dsa/mt7530.c
-+++ b/drivers/net/dsa/mt7530.c
-@@ -235,6 +235,12 @@ mt7530_write(struct mt7530_priv *priv, u
- }
- 
- static u32
-+_mt7530_unlocked_read(struct mt7530_dummy_poll *p)
-+{
-+	return mt7530_mii_read(p->priv, p->reg);
-+}
-+
-+static u32
- _mt7530_read(struct mt7530_dummy_poll *p)
- {
- 	struct mii_bus		*bus = p->priv->bus;
-@@ -482,6 +488,108 @@ mt7530_pad_clk_setup(struct dsa_switch *
- 	return 0;
- }
- 
-+static bool mt7531_dual_sgmii_supported(struct mt7530_priv *priv)
-+{
-+	u32 val;
-+
-+	val = mt7530_read(priv, MT7531_TOP_SIG_SR);
-+
-+	return (val & PAD_DUAL_SGMII_EN) != 0;
-+}
-+
-+static int
-+mt7531_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	u32 val;
-+	u32 top_sig;
-+	u32 hwstrap;
-+	u32 xtal;
-+
-+	if (mt7531_dual_sgmii_supported(priv))
-+		return 0;
-+
-+	val = mt7530_read(priv, MT7531_CREV);
-+	top_sig = mt7530_read(priv, MT7531_TOP_SIG_SR);
-+	hwstrap = mt7530_read(priv, MT7531_HWTRAP);
-+	if ((val & CHIP_REV_M) > 0)
-+		xtal = (top_sig & PAD_MCM_SMI_EN) ? HWTRAP_XTAL_FSEL_40MHZ :
-+						    HWTRAP_XTAL_FSEL_25MHZ;
-+	else
-+		xtal = hwstrap & HWTRAP_XTAL_FSEL_MASK;
-+
-+	/* Step 1 : Disable MT7531 COREPLL */
-+	val = mt7530_read(priv, MT7531_PLLGP_EN);
-+	val &= ~EN_COREPLL;
-+	mt7530_write(priv, MT7531_PLLGP_EN, val);
-+
-+	/* Step 2: switch to XTAL output */
-+	val = mt7530_read(priv, MT7531_PLLGP_EN);
-+	val |= SW_CLKSW;
-+	mt7530_write(priv, MT7531_PLLGP_EN, val);
-+
-+	val = mt7530_read(priv, MT7531_PLLGP_CR0);
-+	val &= ~RG_COREPLL_EN;
-+	mt7530_write(priv, MT7531_PLLGP_CR0, val);
-+
-+	/* Step 3: disable PLLGP and enable program PLLGP */
-+	val = mt7530_read(priv, MT7531_PLLGP_EN);
-+	val |= SW_PLLGP;
-+	mt7530_write(priv, MT7531_PLLGP_EN, val);
-+
-+	/* Step 4: program COREPLL output frequency to 500MHz */
-+	val = mt7530_read(priv, MT7531_PLLGP_CR0);
-+	val &= ~RG_COREPLL_POSDIV_M;
-+	val |= 2 << RG_COREPLL_POSDIV_S;
-+	mt7530_write(priv, MT7531_PLLGP_CR0, val);
-+	usleep_range(25, 35);
-+
-+	switch (xtal) {
-+	case HWTRAP_XTAL_FSEL_25MHZ:
-+		val = mt7530_read(priv, MT7531_PLLGP_CR0);
-+		val &= ~RG_COREPLL_SDM_PCW_M;
-+		val |= 0x140000 << RG_COREPLL_SDM_PCW_S;
-+		mt7530_write(priv, MT7531_PLLGP_CR0, val);
-+		break;
-+	case HWTRAP_XTAL_FSEL_40MHZ:
-+		val = mt7530_read(priv, MT7531_PLLGP_CR0);
-+		val &= ~RG_COREPLL_SDM_PCW_M;
-+		val |= 0x190000 << RG_COREPLL_SDM_PCW_S;
-+		mt7530_write(priv, MT7531_PLLGP_CR0, val);
-+		break;
-+	};
-+
-+	/* Set feedback divide ratio update signal to high */
-+	val = mt7530_read(priv, MT7531_PLLGP_CR0);
-+	val |= RG_COREPLL_SDM_PCW_CHG;
-+	mt7530_write(priv, MT7531_PLLGP_CR0, val);
-+	/* Wait for at least 16 XTAL clocks */
-+	usleep_range(10, 20);
-+
-+	/* Step 5: set feedback divide ratio update signal to low */
-+	val = mt7530_read(priv, MT7531_PLLGP_CR0);
-+	val &= ~RG_COREPLL_SDM_PCW_CHG;
-+	mt7530_write(priv, MT7531_PLLGP_CR0, val);
-+
-+	/* Enable 325M clock for SGMII */
-+	mt7530_write(priv, MT7531_ANA_PLLGP_CR5, 0xad0000);
-+
-+	/* Enable 250SSC clock for RGMII */
-+	mt7530_write(priv, MT7531_ANA_PLLGP_CR2, 0x4f40000);
-+
-+	/* Step 6: Enable MT7531 PLL */
-+	val = mt7530_read(priv, MT7531_PLLGP_CR0);
-+	val |= RG_COREPLL_EN;
-+	mt7530_write(priv, MT7531_PLLGP_CR0, val);
-+
-+	val = mt7530_read(priv, MT7531_PLLGP_EN);
-+	val |= EN_COREPLL;
-+	mt7530_write(priv, MT7531_PLLGP_EN, val);
-+	usleep_range(25, 35);
-+
-+	return 0;
-+}
-+
- static void
- mt7530_mib_reset(struct dsa_switch *ds)
- {
-@@ -506,6 +614,217 @@ static int mt7530_phy_write(struct dsa_s
- 	return mdiobus_write_nested(priv->bus, port, regnum, val);
- }
- 
-+static int
-+mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad,
-+			int regnum)
-+{
-+	struct mii_bus *bus = priv->bus;
-+	struct mt7530_dummy_poll p;
-+	u32 reg, val;
-+	int ret;
-+
-+	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
-+
-+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	reg = MT7531_MDIO_CL45_ADDR | MT7531_MDIO_PHY_ADDR(port) |
-+	      MT7531_MDIO_DEV_ADDR(devad) | regnum;
-+	mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	reg = MT7531_MDIO_CL45_READ | MT7531_MDIO_PHY_ADDR(port) |
-+	      MT7531_MDIO_DEV_ADDR(devad);
-+	mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	ret = val & MT7531_MDIO_RW_DATA_MASK;
-+out:
-+	mutex_unlock(&bus->mdio_lock);
-+
-+	return ret;
-+}
-+
-+static int
-+mt7531_ind_c45_phy_write(struct mt7530_priv *priv, int port, int devad,
-+			 int regnum, u32 data)
-+{
-+	struct mii_bus *bus = priv->bus;
-+	struct mt7530_dummy_poll p;
-+	u32 val, reg;
-+	int ret;
-+
-+	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
-+
-+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	reg = MT7531_MDIO_CL45_ADDR | MT7531_MDIO_PHY_ADDR(port) |
-+	      MT7531_MDIO_DEV_ADDR(devad) | regnum;
-+	mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	reg = MT7531_MDIO_CL45_WRITE | MT7531_MDIO_PHY_ADDR(port) |
-+	      MT7531_MDIO_DEV_ADDR(devad) | data;
-+	mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+out:
-+	mutex_unlock(&bus->mdio_lock);
-+
-+	return ret;
-+}
-+
-+static int
-+mt7531_ind_c22_phy_read(struct mt7530_priv *priv, int port, int regnum)
-+{
-+	struct mii_bus *bus = priv->bus;
-+	struct mt7530_dummy_poll p;
-+	int ret;
-+	u32 val;
-+
-+	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
-+
-+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	val = MT7531_MDIO_CL22_READ | MT7531_MDIO_PHY_ADDR(port) |
-+	      MT7531_MDIO_REG_ADDR(regnum);
-+
-+	mt7530_mii_write(priv, MT7531_PHY_IAC, val | MT7531_PHY_ACS_ST);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
-+				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	ret = val & MT7531_MDIO_RW_DATA_MASK;
-+out:
-+	mutex_unlock(&bus->mdio_lock);
-+
-+	return ret;
-+}
-+
-+static int
-+mt7531_ind_c22_phy_write(struct mt7530_priv *priv, int port, int regnum,
-+			 u16 data)
-+{
-+	struct mii_bus *bus = priv->bus;
-+	struct mt7530_dummy_poll p;
-+	int ret;
-+	u32 reg;
-+
-+	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
-+
-+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, reg,
-+				 !(reg & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+	reg = MT7531_MDIO_CL22_WRITE | MT7531_MDIO_PHY_ADDR(port) |
-+	      MT7531_MDIO_REG_ADDR(regnum) | data;
-+
-+	mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);
-+
-+	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, reg,
-+				 !(reg & MT7531_PHY_ACS_ST), 20, 100000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "poll timeout\n");
-+		goto out;
-+	}
-+
-+out:
-+	mutex_unlock(&bus->mdio_lock);
-+
-+	return ret;
-+}
-+
-+static int
-+mt7531_ind_phy_read(struct dsa_switch *ds, int port, int regnum)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	int devad;
-+	int ret;
-+
-+	if (regnum & MII_ADDR_C45) {
-+		devad = (regnum >> MII_DEVADDR_C45_SHIFT) & 0x1f;
-+		ret = mt7531_ind_c45_phy_read(priv, port, devad,
-+					      regnum & MII_REGADDR_C45_MASK);
-+	} else {
-+		ret = mt7531_ind_c22_phy_read(priv, port, regnum);
-+	}
-+
-+	return ret;
-+}
-+
-+static int
-+mt7531_ind_phy_write(struct dsa_switch *ds, int port, int regnum,
-+		     u16 data)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	int devad;
-+	int ret;
-+
-+	if (regnum & MII_ADDR_C45) {
-+		devad = (regnum >> MII_DEVADDR_C45_SHIFT) & 0x1f;
-+		ret = mt7531_ind_c45_phy_write(priv, port, devad,
-+					       regnum & MII_REGADDR_C45_MASK,
-+					       data);
-+	} else {
-+		ret = mt7531_ind_c22_phy_write(priv, port, regnum, data);
-+	}
-+
-+	return ret;
-+}
-+
- static void
- mt7530_get_strings(struct dsa_switch *ds, int port, u32 stringset,
- 		   uint8_t *data)
-@@ -622,9 +941,14 @@ unlock_exit:
- }
- 
- static int
--mt7530_cpu_port_enable(struct mt7530_priv *priv,
--		       int port)
-+mt753x_cpu_port_enable(struct dsa_switch *ds, int port)
- {
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	/* Setup max capability of CPU port at first */
-+	if (priv->info->cpu_port_config)
-+		priv->info->cpu_port_config(ds, port);
-+
- 	/* Enable Mediatek header mode on the cpu port */
- 	mt7530_write(priv, MT7530_PVC_P(port),
- 		     PORT_SPEC_TAG);
-@@ -637,7 +961,7 @@ mt7530_cpu_port_enable(struct mt7530_pri
- 		mt7530_rmw(priv, MT7530_MFC, CPU_MASK, CPU_EN | CPU_PORT(port));
- 
- 	/* CPU port gets connected to all user ports of
--	 * the switch
-+	 * the switch.
- 	 */
- 	mt7530_write(priv, MT7530_PCR_P(port),
- 		     PCR_MATRIX(dsa_user_ports(priv->ds)));
-@@ -1120,27 +1444,42 @@ mt7530_port_vlan_del(struct dsa_switch *
- 	return 0;
- }
- 
--static int mt7530_port_mirror_add(struct dsa_switch *ds, int port,
-+static int mt753x_mirror_port_get(unsigned int id, u32 val)
-+{
-+	return (id == ID_MT7531) ? MT7531_MIRROR_PORT_GET(val) :
-+				   MIRROR_PORT(val);
-+}
-+
-+static int mt753x_mirror_port_set(unsigned int id, u32 val)
-+{
-+	return (id == ID_MT7531) ? MT7531_MIRROR_PORT_SET(val) :
-+				   MIRROR_PORT(val);
-+}
-+
-+static int mt753x_port_mirror_add(struct dsa_switch *ds, int port,
- 				  struct dsa_mall_mirror_tc_entry *mirror,
- 				  bool ingress)
- {
- 	struct mt7530_priv *priv = ds->priv;
-+	int monitor_port;
- 	u32 val;
- 
- 	/* Check for existent entry */
- 	if ((ingress ? priv->mirror_rx : priv->mirror_tx) & BIT(port))
- 		return -EEXIST;
- 
--	val = mt7530_read(priv, MT7530_MFC);
-+	val = mt7530_read(priv, MT753X_MIRROR_REG(priv->id));
- 
- 	/* MT7530 only supports one monitor port */
--	if (val & MIRROR_EN && MIRROR_PORT(val) != mirror->to_local_port)
-+	monitor_port = mt753x_mirror_port_get(priv->id, val);
-+	if (val & MT753X_MIRROR_EN(priv->id) &&
-+	    monitor_port != mirror->to_local_port)
- 		return -EEXIST;
- 
--	val |= MIRROR_EN;
--	val &= ~MIRROR_MASK;
--	val |= mirror->to_local_port;
--	mt7530_write(priv, MT7530_MFC, val);
-+	val |= MT753X_MIRROR_EN(priv->id);
-+	val &= ~MT753X_MIRROR_MASK(priv->id);
-+	val |= mt753x_mirror_port_set(priv->id, mirror->to_local_port);
-+	mt7530_write(priv, MT753X_MIRROR_REG(priv->id), val);
- 
- 	val = mt7530_read(priv, MT7530_PCR_P(port));
- 	if (ingress) {
-@@ -1155,7 +1494,7 @@ static int mt7530_port_mirror_add(struct
- 	return 0;
- }
- 
--static void mt7530_port_mirror_del(struct dsa_switch *ds, int port,
-+static void mt753x_port_mirror_del(struct dsa_switch *ds, int port,
- 				   struct dsa_mall_mirror_tc_entry *mirror)
- {
- 	struct mt7530_priv *priv = ds->priv;
-@@ -1172,9 +1511,9 @@ static void mt7530_port_mirror_del(struc
- 	mt7530_write(priv, MT7530_PCR_P(port), val);
- 
- 	if (!priv->mirror_rx && !priv->mirror_tx) {
--		val = mt7530_read(priv, MT7530_MFC);
--		val &= ~MIRROR_EN;
--		mt7530_write(priv, MT7530_MFC, val);
-+		val = mt7530_read(priv, MT753X_MIRROR_REG(priv->id));
-+		val &= ~MT753X_MIRROR_EN(priv->id);
-+		mt7530_write(priv, MT753X_MIRROR_REG(priv->id), val);
- 	}
- }
- 
-@@ -1280,7 +1619,7 @@ mt7530_setup(struct dsa_switch *ds)
- 			   PCR_MATRIX_CLR);
- 
- 		if (dsa_is_cpu_port(ds, i))
--			mt7530_cpu_port_enable(priv, i);
-+			mt753x_cpu_port_enable(ds, i);
- 		else
- 			mt7530_port_disable(ds, i);
- 
-@@ -1334,6 +1673,118 @@ mt7530_setup(struct dsa_switch *ds)
- 	return 0;
- }
- 
-+static int
-+mt7531_setup(struct dsa_switch *ds)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	struct mt7530_dummy_poll p;
-+	u32 val, id;
-+	int ret, i;
-+
-+	/* Reset whole chip through gpio pin or memory-mapped registers for
-+	 * different type of hardware
-+	 */
-+	if (priv->mcm) {
-+		reset_control_assert(priv->rstc);
-+		usleep_range(1000, 1100);
-+		reset_control_deassert(priv->rstc);
-+	} else {
-+		gpiod_set_value_cansleep(priv->reset, 0);
-+		usleep_range(1000, 1100);
-+		gpiod_set_value_cansleep(priv->reset, 1);
-+	}
-+
-+	/* Waiting for MT7530 got to stable */
-+	INIT_MT7530_DUMMY_POLL(&p, priv, MT7530_HWTRAP);
-+	ret = readx_poll_timeout(_mt7530_read, &p, val, val != 0,
-+				 20, 1000000);
-+	if (ret < 0) {
-+		dev_err(priv->dev, "reset timeout\n");
-+		return ret;
-+	}
-+
-+	id = mt7530_read(priv, MT7531_CREV);
-+	id >>= CHIP_NAME_SHIFT;
-+
-+	if (id != MT7531_ID) {
-+		dev_err(priv->dev, "chip %x can't be supported\n", id);
-+		return -ENODEV;
-+	}
-+
-+	/* Reset the switch through internal reset */
-+	mt7530_write(priv, MT7530_SYS_CTRL,
-+		     SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
-+		     SYS_CTRL_REG_RST);
-+
-+	if (mt7531_dual_sgmii_supported(priv)) {
-+		priv->p5_intf_sel = P5_INTF_SEL_GMAC5_SGMII;
-+
-+		/* Let ds->slave_mii_bus be able to access external phy. */
-+		mt7530_rmw(priv, MT7531_GPIO_MODE1, MT7531_GPIO11_RG_RXD2_MASK,
-+			   MT7531_EXT_P_MDC_11);
-+		mt7530_rmw(priv, MT7531_GPIO_MODE1, MT7531_GPIO12_RG_RXD3_MASK,
-+			   MT7531_EXT_P_MDIO_12);
-+	} else {
-+		priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
-+	}
-+	dev_dbg(ds->dev, "P5 support %s interface\n",
-+		p5_intf_modes(priv->p5_intf_sel));
-+
-+	mt7530_rmw(priv, MT7531_GPIO_MODE0, MT7531_GPIO0_MASK,
-+		   MT7531_GPIO0_INTERRUPT);
-+
-+	/* Let phylink decide the interface later. */
-+	priv->p5_interface = PHY_INTERFACE_MODE_NA;
-+	priv->p6_interface = PHY_INTERFACE_MODE_NA;
-+
-+	/* Enable PHY core PLL, since phy_device has not yet been created
-+	 * provided for phy_[read,write]_mmd_indirect is called, we provide
-+	 * our own mt7531_ind_mmd_phy_[read,write] to complete this
-+	 * function.
-+	 */
-+	val = mt7531_ind_c45_phy_read(priv, MT753X_CTRL_PHY_ADDR,
-+				      MDIO_MMD_VEND2, CORE_PLL_GROUP4);
-+	val |= MT7531_PHY_PLL_BYPASS_MODE;
-+	val &= ~MT7531_PHY_PLL_OFF;
-+	mt7531_ind_c45_phy_write(priv, MT753X_CTRL_PHY_ADDR, MDIO_MMD_VEND2,
-+				 CORE_PLL_GROUP4, val);
-+
-+	/* BPDU to CPU port */
-+	mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
-+		   BIT(MT7530_CPU_PORT));
-+	mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
-+		   MT753X_BPDU_CPU_ONLY);
-+
-+	/* Enable and reset MIB counters */
-+	mt7530_mib_reset(ds);
-+
-+	for (i = 0; i < MT7530_NUM_PORTS; i++) {
-+		/* Disable forwarding by default on all ports */
-+		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
-+			   PCR_MATRIX_CLR);
-+
-+		mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
-+
-+		if (dsa_is_cpu_port(ds, i))
-+			mt753x_cpu_port_enable(ds, i);
-+		else
-+			mt7530_port_disable(ds, i);
-+
-+		/* Enable consistent egress tag */
-+		mt7530_rmw(priv, MT7530_PVC_P(i), PVC_EG_TAG_MASK,
-+			   PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
-+	}
-+
-+	ds->configure_vlan_while_not_filtering = true;
-+
-+	/* Flush the FDB table */
-+	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
-+	if (ret < 0)
-+		return ret;
-+
-+	return 0;
-+}
-+
- static bool
- mt7530_phy_mode_supported(struct dsa_switch *ds, int port,
- 			  const struct phylink_link_state *state)
-@@ -1372,6 +1823,47 @@ unsupported:
- 	return false;
- }
- 
-+static bool mt7531_is_rgmii_port(struct mt7530_priv *priv, u32 port)
-+{
-+	return (port == 5) && (priv->p5_intf_sel != P5_INTF_SEL_GMAC5_SGMII);
-+}
-+
-+static bool
-+mt7531_phy_supported(struct dsa_switch *ds, int port,
-+		     const struct phylink_link_state *state)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	switch (port) {
-+	case 0: /* Internal phy */
-+	case 1:
-+	case 2:
-+	case 3:
-+	case 4:
-+		if (state->interface != PHY_INTERFACE_MODE_GMII)
-+			goto unsupported;
-+		break;
-+	case 5: /* 2nd cpu port supports either rgmii or sgmii/8023z */
-+		if (mt7531_is_rgmii_port(priv, port))
-+			return phy_interface_mode_is_rgmii(state->interface);
-+		fallthrough;
-+	case 6: /* 1st cpu port supports sgmii/8023z only */
-+		if (state->interface != PHY_INTERFACE_MODE_SGMII &&
-+		    !phy_interface_mode_is_8023z(state->interface))
-+			goto unsupported;
-+		break;
-+	default:
-+		dev_err(priv->dev, "%s: unsupported port: %i\n", __func__,
-+			port);
-+		goto unsupported;
-+	}
-+
-+	return true;
-+
-+unsupported:
-+	return false;
-+}
-+
- static bool
- mt753x_phy_mode_supported(struct dsa_switch *ds, int port,
- 			  const struct phylink_link_state *state)
-@@ -1404,6 +1896,227 @@ mt7530_mac_config(struct dsa_switch *ds,
- 	return 0;
- }
- 
-+static int mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
-+			      phy_interface_t interface,
-+			      struct phy_device *phydev)
-+{
-+	u32 val;
-+
-+	if (!mt7531_is_rgmii_port(priv, port)) {
-+		dev_err(priv->dev, "RGMII mode is not available for port %d\n",
-+			port);
-+		return -EINVAL;
-+	}
-+
-+	val = mt7530_read(priv, MT7531_CLKGEN_CTRL);
-+	val |= GP_CLK_EN;
-+	val &= ~GP_MODE_MASK;
-+	val |= GP_MODE(MT7531_GP_MODE_RGMII);
-+	val &= ~CLK_SKEW_IN_MASK;
-+	val |= CLK_SKEW_IN(MT7531_CLK_SKEW_NO_CHG);
-+	val &= ~CLK_SKEW_OUT_MASK;
-+	val |= CLK_SKEW_OUT(MT7531_CLK_SKEW_NO_CHG);
-+	val |= TXCLK_NO_REVERSE | RXCLK_NO_DELAY;
-+
-+	/* Do not adjust rgmii delay when vendor phy driver presents. */
-+	if (!phydev || phy_driver_is_genphy(phydev)) {
-+		val &= ~(TXCLK_NO_REVERSE | RXCLK_NO_DELAY);
-+		switch (interface) {
-+		case PHY_INTERFACE_MODE_RGMII:
-+			val |= TXCLK_NO_REVERSE;
-+			val |= RXCLK_NO_DELAY;
-+			break;
-+		case PHY_INTERFACE_MODE_RGMII_RXID:
-+			val |= TXCLK_NO_REVERSE;
-+			break;
-+		case PHY_INTERFACE_MODE_RGMII_TXID:
-+			val |= RXCLK_NO_DELAY;
-+			break;
-+		case PHY_INTERFACE_MODE_RGMII_ID:
-+			break;
-+		default:
-+			return -EINVAL;
-+		}
-+	}
-+	mt7530_write(priv, MT7531_CLKGEN_CTRL, val);
-+
-+	return 0;
-+}
-+
-+static void mt7531_sgmii_validate(struct mt7530_priv *priv, int port,
-+				  unsigned long *supported)
-+{
-+	/* Port5 supports ethier RGMII or SGMII.
-+	 * Port6 supports SGMII only.
-+	 */
-+	switch (port) {
-+	case 5:
-+		if (mt7531_is_rgmii_port(priv, port))
-+			break;
-+		fallthrough;
-+	case 6:
-+		phylink_set(supported, 1000baseX_Full);
-+		phylink_set(supported, 2500baseX_Full);
-+		phylink_set(supported, 2500baseT_Full);
-+	}
-+}
-+
-+static void
-+mt7531_sgmii_link_up_force(struct dsa_switch *ds, int port,
-+			   unsigned int mode, phy_interface_t interface,
-+			   int speed, int duplex)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	unsigned int val;
-+
-+	/* For adjusting speed and duplex of SGMII force mode. */
-+	if (interface != PHY_INTERFACE_MODE_SGMII ||
-+	    phylink_autoneg_inband(mode))
-+		return;
-+
-+	/* SGMII force mode setting */
-+	val = mt7530_read(priv, MT7531_SGMII_MODE(port));
-+	val &= ~MT7531_SGMII_IF_MODE_MASK;
-+
-+	switch (speed) {
-+	case SPEED_10:
-+		val |= MT7531_SGMII_FORCE_SPEED_10;
-+		break;
-+	case SPEED_100:
-+		val |= MT7531_SGMII_FORCE_SPEED_100;
-+		break;
-+	case SPEED_1000:
-+		val |= MT7531_SGMII_FORCE_SPEED_1000;
-+		break;
-+	}
-+
-+	/* MT7531 SGMII 1G force mode can only work in full duplex mode,
-+	 * no matter MT7531_SGMII_FORCE_HALF_DUPLEX is set or not.
-+	 */
-+	if ((speed == SPEED_10 || speed == SPEED_100) &&
-+	    duplex != DUPLEX_FULL)
-+		val |= MT7531_SGMII_FORCE_HALF_DUPLEX;
-+
-+	mt7530_write(priv, MT7531_SGMII_MODE(port), val);
-+}
-+
-+static bool mt753x_is_mac_port(u32 port)
-+{
-+	return (port == 5 || port == 6);
-+}
-+
-+static int mt7531_sgmii_setup_mode_force(struct mt7530_priv *priv, u32 port,
-+					 phy_interface_t interface)
-+{
-+	u32 val;
-+
-+	if (!mt753x_is_mac_port(port))
-+		return -EINVAL;
-+
-+	mt7530_set(priv, MT7531_QPHY_PWR_STATE_CTRL(port),
-+		   MT7531_SGMII_PHYA_PWD);
-+
-+	val = mt7530_read(priv, MT7531_PHYA_CTRL_SIGNAL3(port));
-+	val &= ~MT7531_RG_TPHY_SPEED_MASK;
-+	/* Setup 2.5 times faster clock for 2.5Gbps data speeds with 10B/8B
-+	 * encoding.
-+	 */
-+	val |= (interface == PHY_INTERFACE_MODE_2500BASEX) ?
-+		MT7531_RG_TPHY_SPEED_3_125G : MT7531_RG_TPHY_SPEED_1_25G;
-+	mt7530_write(priv, MT7531_PHYA_CTRL_SIGNAL3(port), val);
-+
-+	mt7530_clear(priv, MT7531_PCS_CONTROL_1(port), MT7531_SGMII_AN_ENABLE);
-+
-+	/* MT7531 SGMII 1G and 2.5G force mode can only work in full duplex
-+	 * mode, no matter MT7531_SGMII_FORCE_HALF_DUPLEX is set or not.
-+	 */
-+	mt7530_rmw(priv, MT7531_SGMII_MODE(port),
-+		   MT7531_SGMII_IF_MODE_MASK | MT7531_SGMII_REMOTE_FAULT_DIS,
-+		   MT7531_SGMII_FORCE_SPEED_1000);
-+
-+	mt7530_write(priv, MT7531_QPHY_PWR_STATE_CTRL(port), 0);
-+
-+	return 0;
-+}
-+
-+static int mt7531_sgmii_setup_mode_an(struct mt7530_priv *priv, int port,
-+				      phy_interface_t interface)
-+{
-+	if (!mt753x_is_mac_port(port))
-+		return -EINVAL;
-+
-+	mt7530_set(priv, MT7531_QPHY_PWR_STATE_CTRL(port),
-+		   MT7531_SGMII_PHYA_PWD);
-+
-+	mt7530_rmw(priv, MT7531_PHYA_CTRL_SIGNAL3(port),
-+		   MT7531_RG_TPHY_SPEED_MASK, MT7531_RG_TPHY_SPEED_1_25G);
-+
-+	mt7530_set(priv, MT7531_SGMII_MODE(port),
-+		   MT7531_SGMII_REMOTE_FAULT_DIS |
-+		   MT7531_SGMII_SPEED_DUPLEX_AN);
-+
-+	mt7530_rmw(priv, MT7531_PCS_SPEED_ABILITY(port),
-+		   MT7531_SGMII_TX_CONFIG_MASK, 1);
-+
-+	mt7530_set(priv, MT7531_PCS_CONTROL_1(port), MT7531_SGMII_AN_ENABLE);
-+
-+	mt7530_set(priv, MT7531_PCS_CONTROL_1(port), MT7531_SGMII_AN_RESTART);
-+
-+	mt7530_write(priv, MT7531_QPHY_PWR_STATE_CTRL(port), 0);
-+
-+	return 0;
-+}
-+
-+static void mt7531_sgmii_restart_an(struct dsa_switch *ds, int port)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	u32 val;
-+
-+	/* Only restart AN when AN is enabled */
-+	val = mt7530_read(priv, MT7531_PCS_CONTROL_1(port));
-+	if (val & MT7531_SGMII_AN_ENABLE) {
-+		val |= MT7531_SGMII_AN_RESTART;
-+		mt7530_write(priv, MT7531_PCS_CONTROL_1(port), val);
-+	}
-+}
-+
-+static int
-+mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
-+		  phy_interface_t interface)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	struct phy_device *phydev;
-+	const struct dsa_port *dp;
-+
-+	if (!mt753x_is_mac_port(port)) {
-+		dev_err(priv->dev, "port %d is not a MAC port\n", port);
-+		return -EINVAL;
-+	}
-+
-+	switch (interface) {
-+	case PHY_INTERFACE_MODE_RGMII:
-+	case PHY_INTERFACE_MODE_RGMII_ID:
-+	case PHY_INTERFACE_MODE_RGMII_RXID:
-+	case PHY_INTERFACE_MODE_RGMII_TXID:
-+		dp = dsa_to_port(ds, port);
-+		phydev = dp->slave->phydev;
-+		return mt7531_rgmii_setup(priv, port, interface, phydev);
-+	case PHY_INTERFACE_MODE_SGMII:
-+		return mt7531_sgmii_setup_mode_an(priv, port, interface);
-+	case PHY_INTERFACE_MODE_NA:
-+	case PHY_INTERFACE_MODE_1000BASEX:
-+	case PHY_INTERFACE_MODE_2500BASEX:
-+		if (phylink_autoneg_inband(mode))
-+			return -EINVAL;
-+
-+		return mt7531_sgmii_setup_mode_force(priv, port, interface);
-+	default:
-+		return -EINVAL;
-+	}
-+
-+	return -EINVAL;
-+}
-+
- static int
- mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
- 		  const struct phylink_link_state *state)
-@@ -1439,6 +2152,8 @@ mt753x_phylink_mac_config(struct dsa_swi
- 		if (mt753x_mac_config(ds, port, mode, state) < 0)
- 			goto unsupported;
- 
-+		if (priv->p5_intf_sel != P5_DISABLED)
-+			priv->p5_interface = state->interface;
- 		break;
- 	case 6: /* 1st cpu port */
- 		if (priv->p6_interface == state->interface)
-@@ -1458,7 +2173,8 @@ unsupported:
- 		return;
- 	}
- 
--	if (phylink_autoneg_inband(mode)) {
-+	if (phylink_autoneg_inband(mode) &&
-+	    state->interface != PHY_INTERFACE_MODE_SGMII) {
- 		dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
- 			__func__);
- 		return;
-@@ -1468,7 +2184,7 @@ unsupported:
- 	mcr_new = mcr_cur;
- 	mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
- 	mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
--		   PMCR_BACKPR_EN | PMCR_FORCE_MODE;
-+		   PMCR_BACKPR_EN | PMCR_FORCE_MODE_ID(priv->id);
- 
- 	/* Are we connected to external phy */
- 	if (port == 5 && dsa_is_user_port(ds, 5))
-@@ -1478,7 +2194,18 @@ unsupported:
- 		mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
- }
- 
--static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
-+static void
-+mt753x_phylink_mac_an_restart(struct dsa_switch *ds, int port)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	if (!priv->info->mac_pcs_an_restart)
-+		return;
-+
-+	priv->info->mac_pcs_an_restart(ds, port);
-+}
-+
-+static void mt753x_phylink_mac_link_down(struct dsa_switch *ds, int port,
- 					 unsigned int mode,
- 					 phy_interface_t interface)
- {
-@@ -1487,7 +2214,19 @@ static void mt7530_phylink_mac_link_down
- 	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
- }
- 
--static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
-+static void mt753x_mac_pcs_link_up(struct dsa_switch *ds, int port,
-+				   unsigned int mode, phy_interface_t interface,
-+				   int speed, int duplex)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	if (!priv->info->mac_pcs_link_up)
-+		return;
-+
-+	priv->info->mac_pcs_link_up(ds, port, mode, interface, speed, duplex);
-+}
-+
-+static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port,
- 				       unsigned int mode,
- 				       phy_interface_t interface,
- 				       struct phy_device *phydev,
-@@ -1497,18 +2236,29 @@ static void mt7530_phylink_mac_link_up(s
- 	struct mt7530_priv *priv = ds->priv;
- 	u32 mcr;
- 
-+	mt753x_mac_pcs_link_up(ds, port, mode, interface, speed, duplex);
-+
- 	mcr = PMCR_RX_EN | PMCR_TX_EN | PMCR_FORCE_LNK;
- 
-+	/* MT753x MAC works in 1G full duplex mode for all up-clocked
-+	 * variants.
-+	 */
-+	if (interface == PHY_INTERFACE_MODE_TRGMII ||
-+	    (phy_interface_mode_is_8023z(interface))) {
-+		speed = SPEED_1000;
-+		duplex = DUPLEX_FULL;
-+	}
-+
- 	switch (speed) {
- 	case SPEED_1000:
- 		mcr |= PMCR_FORCE_SPEED_1000;
- 		if (priv->eee_enable & BIT(port))
--			mcr_new |= PMCR_FORCE_EEE1G;
-+			mcr |= PMCR_FORCE_EEE1G;
- 		break;
- 	case SPEED_100:
- 		mcr |= PMCR_FORCE_SPEED_100;
- 		if (priv->eee_enable & BIT(port))
--			mcr_new |= PMCR_FORCE_EEE100;
-+			mcr |= PMCR_FORCE_EEE100;
- 		break;
- 	}
- 	if (duplex == DUPLEX_FULL) {
-@@ -1522,6 +2272,45 @@ static void mt7530_phylink_mac_link_up(s
- 	mt7530_set(priv, MT7530_PMCR_P(port), mcr);
- }
- 
-+static int
-+mt7531_cpu_port_config(struct dsa_switch *ds, int port)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+	phy_interface_t interface;
-+	int speed;
-+
-+	switch (port) {
-+	case 5:
-+		if (mt7531_is_rgmii_port(priv, port))
-+			interface = PHY_INTERFACE_MODE_RGMII;
-+		else
-+			interface = PHY_INTERFACE_MODE_2500BASEX;
-+
-+		priv->p5_interface = interface;
-+		break;
-+	case 6:
-+		interface = PHY_INTERFACE_MODE_2500BASEX;
-+
-+		mt7531_pad_setup(ds, interface);
-+
-+		priv->p6_interface = interface;
-+		break;
-+	};
-+
-+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
-+		speed = SPEED_2500;
-+	else
-+		speed = SPEED_1000;
-+
-+	mt7531_mac_config(ds, port, MLO_AN_FIXED, interface);
-+	mt7530_write(priv, MT7530_PMCR_P(port),
-+		     PMCR_CPU_PORT_SETTING(priv->id));
-+	mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED, interface, NULL,
-+				   speed, DUPLEX_FULL, true, true);
-+
-+	return 0;
-+}
-+
- static void
- mt7530_mac_port_validate(struct dsa_switch *ds, int port,
- 			 unsigned long *supported)
-@@ -1530,6 +2319,14 @@ mt7530_mac_port_validate(struct dsa_swit
- 		phylink_set(supported, 1000baseX_Full);
- }
- 
-+static void mt7531_mac_port_validate(struct dsa_switch *ds, int port,
-+				     unsigned long *supported)
-+{
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	mt7531_sgmii_validate(priv, port, supported);
-+}
-+
- static void
- mt753x_phylink_validate(struct dsa_switch *ds, int port,
- 			unsigned long *supported,
-@@ -1546,7 +2343,8 @@ mt753x_phylink_validate(struct dsa_switc
- 
- 	phylink_set_port_modes(mask);
- 
--	if (state->interface != PHY_INTERFACE_MODE_TRGMII) {
-+	if (state->interface != PHY_INTERFACE_MODE_TRGMII ||
-+	    !phy_interface_mode_is_8023z(state->interface)) {
- 		phylink_set(mask, 10baseT_Half);
- 		phylink_set(mask, 10baseT_Full);
- 		phylink_set(mask, 100baseT_Half);
-@@ -1565,6 +2363,11 @@ mt753x_phylink_validate(struct dsa_switc
- 
- 	linkmode_and(supported, supported, mask);
- 	linkmode_and(state->advertising, state->advertising, mask);
-+
-+	/* We can only operate at 2500BaseX or 1000BaseX.  If requested
-+	 * to advertise both, only report advertising at 2500BaseX.
-+	 */
-+	phylink_helper_basex_speed(state);
- }
- 
- static int
-@@ -1655,6 +2458,63 @@ static int mt7530_set_mac_eee(struct dsa
- 	return 0;
- }
- 
-+#ifdef notyet
-+static int
-+mt7531_sgmii_pcs_get_state_an(struct mt7530_priv *priv, int port,
-+			      struct phylink_link_state *state)
-+{
-+	u32 status, val;
-+	u16 config_reg;
-+
-+	status = mt7530_read(priv, MT7531_PCS_CONTROL_1(port));
-+	state->link = !!(status & MT7531_SGMII_LINK_STATUS);
-+	if (state->interface == PHY_INTERFACE_MODE_SGMII &&
-+	    (status & MT7531_SGMII_AN_ENABLE)) {
-+		val = mt7530_read(priv, MT7531_PCS_SPEED_ABILITY(port));
-+		config_reg = val >> 16;
-+
-+		switch (config_reg & LPA_SGMII_SPD_MASK) {
-+		case LPA_SGMII_1000:
-+			state->speed = SPEED_1000;
-+			break;
-+		case LPA_SGMII_100:
-+			state->speed = SPEED_100;
-+			break;
-+		case LPA_SGMII_10:
-+			state->speed = SPEED_10;
-+			break;
-+		default:
-+			dev_err(priv->dev, "invalid sgmii PHY speed\n");
-+			state->link = false;
-+			return -EINVAL;
-+		}
-+
-+		if (config_reg & LPA_SGMII_FULL_DUPLEX)
-+			state->duplex = DUPLEX_FULL;
-+		else
-+			state->duplex = DUPLEX_HALF;
-+	}
-+
-+	return 0;
-+}
-+#endif
-+
-+static int
-+mt7531_phylink_mac_link_state(struct dsa_switch *ds, int port,
-+			      struct phylink_link_state *state)
-+{
-+#ifdef notyet
-+	struct mt7530_priv *priv = ds->priv;
-+
-+	if (state->interface == PHY_INTERFACE_MODE_SGMII)
-+		return mt7531_sgmii_pcs_get_state_an(priv, port, state);
-+#else
-+	return mt7530_phylink_mac_link_state(ds, port, state);
-+#endif
-+
-+	return -EOPNOTSUPP;
-+}
-+
- static int
- mt753x_phylink_mac_link_state(struct dsa_switch *ds, int port,
- 			      struct phylink_link_state *state)
-@@ -1708,13 +2568,14 @@ static const struct dsa_switch_ops mt753
- 	.port_vlan_prepare	= mt7530_port_vlan_prepare,
- 	.port_vlan_add		= mt7530_port_vlan_add,
- 	.port_vlan_del		= mt7530_port_vlan_del,
--	.port_mirror_add	= mt7530_port_mirror_add,
--	.port_mirror_del	= mt7530_port_mirror_del,
-+	.port_mirror_add	= mt753x_port_mirror_add,
-+	.port_mirror_del	= mt753x_port_mirror_del,
- 	.phylink_validate	= mt753x_phylink_validate,
- 	.phylink_mac_link_state	= mt753x_phylink_mac_link_state,
- 	.phylink_mac_config	= mt753x_phylink_mac_config,
--	.phylink_mac_link_down	= mt7530_phylink_mac_link_down,
--	.phylink_mac_link_up	= mt7530_phylink_mac_link_up,
-+	.phylink_mac_an_restart	= mt753x_phylink_mac_an_restart,
-+	.phylink_mac_link_down	= mt753x_phylink_mac_link_down,
-+	.phylink_mac_link_up	= mt753x_phylink_mac_link_up,
- 	.get_mac_eee		= mt7530_get_mac_eee,
- 	.set_mac_eee		= mt7530_set_mac_eee,
- };
-@@ -1742,11 +2603,26 @@ static const struct mt753x_info mt753x_t
- 		.mac_port_get_state = mt7530_phylink_mac_link_state,
- 		.mac_port_config = mt7530_mac_config,
- 	},
-+	[ID_MT7531] = {
-+		.id = ID_MT7531,
-+		.sw_setup = mt7531_setup,
-+		.phy_read = mt7531_ind_phy_read,
-+		.phy_write = mt7531_ind_phy_write,
-+		.pad_setup = mt7531_pad_setup,
-+		.cpu_port_config = mt7531_cpu_port_config,
-+		.phy_mode_supported = mt7531_phy_supported,
-+		.mac_port_validate = mt7531_mac_port_validate,
-+		.mac_port_get_state = mt7531_phylink_mac_link_state,
-+		.mac_port_config = mt7531_mac_config,
-+		.mac_pcs_an_restart = mt7531_sgmii_restart_an,
-+		.mac_pcs_link_up = mt7531_sgmii_link_up_force,
-+	},
- };
- 
- static const struct of_device_id mt7530_of_match[] = {
- 	{ .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], },
- 	{ .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], },
-+	{ .compatible = "mediatek,mt7531", .data = &mt753x_table[ID_MT7531], },
- 	{ /* sentinel */ },
- };
- MODULE_DEVICE_TABLE(of, mt7530_of_match);
---- a/drivers/net/dsa/mt7530.h
-+++ b/drivers/net/dsa/mt7530.h
-@@ -14,6 +14,7 @@
- enum mt753x_id {
- 	ID_MT7530 = 0,
- 	ID_MT7621 = 1,
-+	ID_MT7531 = 2,
- };
- 
- #define	NUM_TRGMII_CTRL			5
-@@ -41,6 +42,33 @@ enum mt753x_id {
- #define  MIRROR_PORT(x)			((x) & 0x7)
- #define  MIRROR_MASK			0x7
- 
-+/* Registers for CPU forward control */
-+#define MT7531_CFC			0x4
-+#define  MT7531_MIRROR_EN		BIT(19)
-+#define  MT7531_MIRROR_MASK		(MIRROR_MASK << 16)
-+#define  MT7531_MIRROR_PORT_GET(x)	(((x) >> 16) & MIRROR_MASK)
-+#define  MT7531_MIRROR_PORT_SET(x)	(((x) & MIRROR_MASK) << 16)
-+#define  MT7531_CPU_PMAP_MASK		GENMASK(7, 0)
-+
-+#define MT753X_MIRROR_REG(id)		(((id) == ID_MT7531) ? \
-+					 MT7531_CFC : MT7530_MFC)
-+#define MT753X_MIRROR_EN(id)		(((id) == ID_MT7531) ? \
-+					 MT7531_MIRROR_EN : MIRROR_EN)
-+#define MT753X_MIRROR_MASK(id)		(((id) == ID_MT7531) ? \
-+					 MT7531_MIRROR_MASK : MIRROR_MASK)
-+
-+/* Registers for BPDU and PAE frame control*/
-+#define MT753X_BPC			0x24
-+#define  MT753X_BPDU_PORT_FW_MASK	GENMASK(2, 0)
-+
-+enum mt753x_bpdu_port_fw {
-+	MT753X_BPDU_FOLLOW_MFC,
-+	MT753X_BPDU_CPU_EXCLUDE = 4,
-+	MT753X_BPDU_CPU_INCLUDE = 5,
-+	MT753X_BPDU_CPU_ONLY = 6,
-+	MT753X_BPDU_DROP = 7,
-+};
-+
- /* Registers for address table access */
- #define MT7530_ATA1			0x74
- #define  STATIC_EMP			0
-@@ -222,10 +250,30 @@ enum mt7530_vlan_port_attr {
- #define  PMCR_FORCE_LNK			BIT(0)
- #define  PMCR_SPEED_MASK		(PMCR_FORCE_SPEED_100 | \
- 					 PMCR_FORCE_SPEED_1000)
-+#define  MT7531_FORCE_LNK		BIT(31)
-+#define  MT7531_FORCE_SPD		BIT(30)
-+#define  MT7531_FORCE_DPX		BIT(29)
-+#define  MT7531_FORCE_RX_FC		BIT(28)
-+#define  MT7531_FORCE_TX_FC		BIT(27)
-+#define  MT7531_FORCE_MODE		(MT7531_FORCE_LNK | \
-+					 MT7531_FORCE_SPD | \
-+					 MT7531_FORCE_DPX | \
-+					 MT7531_FORCE_RX_FC | \
-+					 MT7531_FORCE_TX_FC)
-+#define  PMCR_FORCE_MODE_ID(id)		(((id) == ID_MT7531) ? \
-+					 MT7531_FORCE_MODE : \
-+					 PMCR_FORCE_MODE)
- #define  PMCR_LINK_SETTINGS_MASK	(PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
- 					 PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
- 					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
- 					 PMCR_FORCE_FDX | PMCR_FORCE_LNK)
-+#define  PMCR_CPU_PORT_SETTING(id)	(PMCR_FORCE_MODE_ID((id)) | \
-+					 PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
-+					 PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \
-+					 PMCR_TX_EN | PMCR_RX_EN | \
-+					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
-+					 PMCR_FORCE_SPEED_1000 | \
-+					 PMCR_FORCE_FDX | PMCR_FORCE_LNK)
- 
- #define MT7530_PMSR_P(x)		(0x3008 + (x) * 0x100)
- #define  PMSR_EEE1G			BIT(7)
-@@ -245,6 +293,10 @@ enum mt7530_vlan_port_attr {
- #define  LPI_THRESH(x)			((x & 0xFFF) << 4)
- #define  LPI_MODE_EN			BIT(0)
- 
-+/* Register for port debug count */
-+#define MT7531_DBG_CNT(x)		(0x3018 + (x) * 0x100)
-+#define  MT7531_DIS_CLR			BIT(31)
-+
- /* Register for MIB */
- #define MT7530_PORT_MIB_COUNTER(x)	(0x4000 + (x) * 0x100)
- #define MT7530_MIB_CCR			0x4fe0
-@@ -262,12 +314,118 @@ enum mt7530_vlan_port_attr {
- 					 CCR_RX_OCT_CNT_BAD | \
- 					 CCR_TX_OCT_CNT_GOOD | \
- 					 CCR_TX_OCT_CNT_BAD)
-+
-+/* MT7531 SGMII register group */
-+#define MT7531_SGMII_REG_BASE		0x5000
-+#define MT7531_SGMII_REG(p, r)		(MT7531_SGMII_REG_BASE + \
-+					((p) - 5) * 0x1000 + (r))
-+
-+/* Register forSGMII PCS_CONTROL_1 */
-+#define MT7531_PCS_CONTROL_1(p)		MT7531_SGMII_REG(p, 0x00)
-+#define  MT7531_SGMII_LINK_STATUS	BIT(18)
-+#define  MT7531_SGMII_AN_ENABLE		BIT(12)
-+#define  MT7531_SGMII_AN_RESTART	BIT(9)
-+
-+/* Register for SGMII PCS_SPPED_ABILITY */
-+#define MT7531_PCS_SPEED_ABILITY(p)	MT7531_SGMII_REG(p, 0x08)
-+#define  MT7531_SGMII_TX_CONFIG_MASK	GENMASK(15, 0)
-+#define  MT7531_SGMII_TX_CONFIG		BIT(0)
-+
-+/* Register for SGMII_MODE */
-+#define MT7531_SGMII_MODE(p)		MT7531_SGMII_REG(p, 0x20)
-+#define  MT7531_SGMII_REMOTE_FAULT_DIS	BIT(8)
-+#define  MT7531_SGMII_IF_MODE_MASK	GENMASK(5, 1)
-+#define  MT7531_SGMII_FORCE_DUPLEX	BIT(4)
-+#define  MT7531_SGMII_FORCE_SPEED_MASK	GENMASK(3, 2)
-+#define  MT7531_SGMII_FORCE_SPEED_1000	BIT(3)
-+#define  MT7531_SGMII_FORCE_SPEED_100	BIT(2)
-+#define  MT7531_SGMII_FORCE_SPEED_10	0
-+#define  MT7531_SGMII_SPEED_DUPLEX_AN	BIT(1)
-+
-+enum mt7531_sgmii_force_duplex {
-+	MT7531_SGMII_FORCE_FULL_DUPLEX = 0,
-+	MT7531_SGMII_FORCE_HALF_DUPLEX = 0x10,
-+};
-+
-+/* Fields of QPHY_PWR_STATE_CTRL */
-+#define MT7531_QPHY_PWR_STATE_CTRL(p)	MT7531_SGMII_REG(p, 0xe8)
-+#define  MT7531_SGMII_PHYA_PWD		BIT(4)
-+
-+/* Values of SGMII SPEED */
-+#define MT7531_PHYA_CTRL_SIGNAL3(p)	MT7531_SGMII_REG(p, 0x128)
-+#define  MT7531_RG_TPHY_SPEED_MASK	(BIT(2) | BIT(3))
-+#define  MT7531_RG_TPHY_SPEED_1_25G	0x0
-+#define  MT7531_RG_TPHY_SPEED_3_125G	BIT(2)
-+
- /* Register for system reset */
- #define MT7530_SYS_CTRL			0x7000
- #define  SYS_CTRL_PHY_RST		BIT(2)
- #define  SYS_CTRL_SW_RST		BIT(1)
- #define  SYS_CTRL_REG_RST		BIT(0)
- 
-+/* Register for PHY Indirect Access Control */
-+#define MT7531_PHY_IAC			0x701C
-+#define  MT7531_PHY_ACS_ST		BIT(31)
-+#define  MT7531_MDIO_REG_ADDR_MASK	(0x1f << 25)
-+#define  MT7531_MDIO_PHY_ADDR_MASK	(0x1f << 20)
-+#define  MT7531_MDIO_CMD_MASK		(0x3 << 18)
-+#define  MT7531_MDIO_ST_MASK		(0x3 << 16)
-+#define  MT7531_MDIO_RW_DATA_MASK	(0xffff)
-+#define  MT7531_MDIO_REG_ADDR(x)	(((x) & 0x1f) << 25)
-+#define  MT7531_MDIO_DEV_ADDR(x)	(((x) & 0x1f) << 25)
-+#define  MT7531_MDIO_PHY_ADDR(x)	(((x) & 0x1f) << 20)
-+#define  MT7531_MDIO_CMD(x)		(((x) & 0x3) << 18)
-+#define  MT7531_MDIO_ST(x)		(((x) & 0x3) << 16)
-+
-+enum mt7531_phy_iac_cmd {
-+	MT7531_MDIO_ADDR = 0,
-+	MT7531_MDIO_WRITE = 1,
-+	MT7531_MDIO_READ = 2,
-+	MT7531_MDIO_READ_CL45 = 3,
-+};
-+
-+/* MDIO_ST: MDIO start field */
-+enum mt7531_mdio_st {
-+	MT7531_MDIO_ST_CL45 = 0,
-+	MT7531_MDIO_ST_CL22 = 1,
-+};
-+
-+#define  MT7531_MDIO_CL22_READ		(MT7531_MDIO_ST(MT7531_MDIO_ST_CL22) | \
-+					 MT7531_MDIO_CMD(MT7531_MDIO_READ))
-+#define  MT7531_MDIO_CL22_WRITE		(MT7531_MDIO_ST(MT7531_MDIO_ST_CL22) | \
-+					 MT7531_MDIO_CMD(MT7531_MDIO_WRITE))
-+#define  MT7531_MDIO_CL45_ADDR		(MT7531_MDIO_ST(MT7531_MDIO_ST_CL45) | \
-+					 MT7531_MDIO_CMD(MT7531_MDIO_ADDR))
-+#define  MT7531_MDIO_CL45_READ		(MT7531_MDIO_ST(MT7531_MDIO_ST_CL45) | \
-+					 MT7531_MDIO_CMD(MT7531_MDIO_READ))
-+#define  MT7531_MDIO_CL45_WRITE		(MT7531_MDIO_ST(MT7531_MDIO_ST_CL45) | \
-+					 MT7531_MDIO_CMD(MT7531_MDIO_WRITE))
-+
-+/* Register for RGMII clock phase */
-+#define MT7531_CLKGEN_CTRL		0x7500
-+#define  CLK_SKEW_OUT(x)		(((x) & 0x3) << 8)
-+#define  CLK_SKEW_OUT_MASK		GENMASK(9, 8)
-+#define  CLK_SKEW_IN(x)			(((x) & 0x3) << 6)
-+#define  CLK_SKEW_IN_MASK		GENMASK(7, 6)
-+#define  RXCLK_NO_DELAY			BIT(5)
-+#define  TXCLK_NO_REVERSE		BIT(4)
-+#define  GP_MODE(x)			(((x) & 0x3) << 1)
-+#define  GP_MODE_MASK			GENMASK(2, 1)
-+#define  GP_CLK_EN			BIT(0)
-+
-+enum mt7531_gp_mode {
-+	MT7531_GP_MODE_RGMII = 0,
-+	MT7531_GP_MODE_MII = 1,
-+	MT7531_GP_MODE_REV_MII = 2
-+};
-+
-+enum mt7531_clk_skew {
-+	MT7531_CLK_SKEW_NO_CHG = 0,
-+	MT7531_CLK_SKEW_DLY_100PPS = 1,
-+	MT7531_CLK_SKEW_DLY_200PPS = 2,
-+	MT7531_CLK_SKEW_REVERSE = 3,
-+};
-+
- /* Register for hw trap status */
- #define MT7530_HWTRAP			0x7800
- #define  HWTRAP_XTAL_MASK		(BIT(10) | BIT(9))
-@@ -275,6 +433,16 @@ enum mt7530_vlan_port_attr {
- #define  HWTRAP_XTAL_40MHZ		(BIT(10))
- #define  HWTRAP_XTAL_20MHZ		(BIT(9))
- 
-+#define MT7531_HWTRAP			0x7800
-+#define  HWTRAP_XTAL_FSEL_MASK		BIT(7)
-+#define  HWTRAP_XTAL_FSEL_25MHZ		BIT(7)
-+#define  HWTRAP_XTAL_FSEL_40MHZ		0
-+/* Unique fields of (M)HWSTRAP for MT7531 */
-+#define  XTAL_FSEL_S			7
-+#define  XTAL_FSEL_M			BIT(7)
-+#define  PHY_EN				BIT(6)
-+#define  CHG_STRAP			BIT(8)
-+
- /* Register for hw trap modification */
- #define MT7530_MHWTRAP			0x7804
- #define  MHWTRAP_PHY0_SEL		BIT(20)
-@@ -289,14 +457,37 @@ enum mt7530_vlan_port_attr {
- #define MT7530_TOP_SIG_CTRL		0x7808
- #define  TOP_SIG_CTRL_NORMAL		(BIT(17) | BIT(16))
- 
-+#define MT7531_TOP_SIG_SR		0x780c
-+#define  PAD_DUAL_SGMII_EN		BIT(1)
-+#define  PAD_MCM_SMI_EN			BIT(0)
-+
- #define MT7530_IO_DRV_CR		0x7810
- #define  P5_IO_CLK_DRV(x)		((x) & 0x3)
- #define  P5_IO_DATA_DRV(x)		(((x) & 0x3) << 4)
- 
-+#define MT7531_CHIP_REV			0x781C
-+
-+#define MT7531_PLLGP_EN			0x7820
-+#define  EN_COREPLL			BIT(2)
-+#define  SW_CLKSW			BIT(1)
-+#define  SW_PLLGP			BIT(0)
-+
- #define MT7530_P6ECR			0x7830
- #define  P6_INTF_MODE_MASK		0x3
- #define  P6_INTF_MODE(x)		((x) & 0x3)
- 
-+#define MT7531_PLLGP_CR0		0x78a8
-+#define  RG_COREPLL_EN			BIT(22)
-+#define  RG_COREPLL_POSDIV_S		23
-+#define  RG_COREPLL_POSDIV_M		0x3800000
-+#define  RG_COREPLL_SDM_PCW_S		1
-+#define  RG_COREPLL_SDM_PCW_M		0x3ffffe
-+#define  RG_COREPLL_SDM_PCW_CHG		BIT(0)
-+
-+/* Registers for RGMII and SGMII PLL clock */
-+#define MT7531_ANA_PLLGP_CR2		0x78b0
-+#define MT7531_ANA_PLLGP_CR5		0x78bc
-+
- /* Registers for TRGMII on the both side */
- #define MT7530_TRGMII_RCK_CTRL		0x7a00
- #define  RX_RST				BIT(31)
-@@ -335,10 +526,25 @@ enum mt7530_vlan_port_attr {
- #define MT7530_P5RGMIITXCR		0x7b04
- #define  CSR_RGMII_TXC_CFG(x)		((x) & 0x1f)
- 
-+/* Registers for GPIO mode */
-+#define MT7531_GPIO_MODE0		0x7c0c
-+#define  MT7531_GPIO0_MASK		GENMASK(3, 0)
-+#define  MT7531_GPIO0_INTERRUPT		1
-+
-+#define MT7531_GPIO_MODE1		0x7c10
-+#define  MT7531_GPIO11_RG_RXD2_MASK	GENMASK(15, 12)
-+#define  MT7531_EXT_P_MDC_11		(2 << 12)
-+#define  MT7531_GPIO12_RG_RXD3_MASK	GENMASK(19, 16)
-+#define  MT7531_EXT_P_MDIO_12		(2 << 16)
-+
- #define MT7530_CREV			0x7ffc
- #define  CHIP_NAME_SHIFT		16
- #define  MT7530_ID			0x7530
- 
-+#define MT7531_CREV			0x781C
-+#define  CHIP_REV_M			0x0f
-+#define  MT7531_ID			0x7531
-+
- /* Registers for core PLL access through mmd indirect */
- #define CORE_PLL_GROUP2			0x401
- #define  RG_SYSPLL_EN_NORMAL		BIT(15)
-@@ -355,6 +561,10 @@ enum mt7530_vlan_port_attr {
- #define  RG_SYSPLL_DDSFBK_EN		BIT(12)
- #define  RG_SYSPLL_BIAS_EN		BIT(11)
- #define  RG_SYSPLL_BIAS_LPF_EN		BIT(10)
-+#define  MT7531_PHY_PLL_OFF		BIT(5)
-+#define  MT7531_PHY_PLL_BYPASS_MODE	BIT(4)
-+
-+#define MT753X_CTRL_PHY_ADDR		0
- 
- #define CORE_PLL_GROUP5			0x404
- #define  RG_LCDDS_PCW_NCPO1(x)		((x) & 0xffff)
-@@ -433,6 +643,7 @@ enum p5_interface_select {
- 	P5_INTF_SEL_PHY_P0,
- 	P5_INTF_SEL_PHY_P4,
- 	P5_INTF_SEL_GMAC5,
-+	P5_INTF_SEL_GMAC5_SGMII,
- };
- 
- static const char *p5_intf_modes(unsigned int p5_interface)
-@@ -446,6 +657,8 @@ static const char *p5_intf_modes(unsigne
- 		return "PHY P4";
- 	case P5_INTF_SEL_GMAC5:
- 		return "GMAC5";
-+	case P5_INTF_SEL_GMAC5_SGMII:
-+		return "GMAC5_SGMII";
- 	default:
- 		return "unknown";
- 	}
-@@ -466,6 +679,10 @@ static const char *p5_intf_modes(unsigne
-  *			MAC port
-  * @mac_port_config:	Holding the way setting up the PHY attribute to a
-  *			certain MAC port
-+ * @mac_pcs_an_restart	Holding the way restarting PCS autonegotiation for a
-+ *			certain MAC port
-+ * @mac_pcs_link_up:	Holding the way setting up the PHY attribute to the pcs
-+ *			of the certain MAC port
-  */
- struct mt753x_info {
- 	enum mt753x_id id;
-@@ -474,6 +691,7 @@ struct mt753x_info {
- 	int (*phy_read)(struct dsa_switch *ds, int port, int regnum);
- 	int (*phy_write)(struct dsa_switch *ds, int port, int regnum, u16 val);
- 	int (*pad_setup)(struct dsa_switch *ds, phy_interface_t interface);
-+	int (*cpu_port_config)(struct dsa_switch *ds, int port);
- 	bool (*phy_mode_supported)(struct dsa_switch *ds, int port,
- 				   const struct phylink_link_state *state);
- 	void (*mac_port_validate)(struct dsa_switch *ds, int port,
-@@ -483,6 +701,10 @@ struct mt753x_info {
- 	int (*mac_port_config)(struct dsa_switch *ds, int port,
- 			       unsigned int mode,
- 			       phy_interface_t interface);
-+	void (*mac_pcs_an_restart)(struct dsa_switch *ds, int port);
-+	void (*mac_pcs_link_up)(struct dsa_switch *ds, int port,
-+				unsigned int mode, phy_interface_t interface,
-+				int speed, int duplex);
- };
- 
- /* struct mt7530_priv -	This is the main data structure for holding the state
diff --git a/target/linux/mediatek/patches-5.4/0605-arm64-dts-mt7622-add-mt7531-dsa-to-bananapi-bpi-r64-board.patch b/target/linux/mediatek/patches-5.4/0605-arm64-dts-mt7622-add-mt7531-dsa-to-bananapi-bpi-r64-board.patch
deleted file mode 100644
index 8c3fe52089..0000000000
--- a/target/linux/mediatek/patches-5.4/0605-arm64-dts-mt7622-add-mt7531-dsa-to-bananapi-bpi-r64-board.patch
+++ /dev/null
@@ -1,71 +0,0 @@
-From: Landen Chao <landen.chao@mediatek.com>
-Subject: [PATCH net-next 6/6] arm64: dts: mt7622: add mt7531 dsa to
- bananapi-bpi-r64 board
-Date: Tue, 10 Dec 2019 16:14:42 +0800
-
-Add mt7531 dsa to bananapi-bpi-r64 board for 5 giga Ethernet ports support.
-
-Signed-off-by: Landen Chao <landen.chao@mediatek.com>
----
- .../dts/mediatek/mt7622-bananapi-bpi-r64.dts  | 50 +++++++++++++++++++
- 1 file changed, 50 insertions(+)
-
---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-@@ -150,6 +150,56 @@
- 	mdio: mdio-bus {
- 		#address-cells = <1>;
- 		#size-cells = <0>;
-+
-+		switch@0 {
-+			compatible = "mediatek,mt7531";
-+			reg = <0>;
-+			reset-gpios = <&pio 54 0>;
-+
-+			ports {
-+				#address-cells = <1>;
-+				#size-cells = <0>;
-+
-+				port@0 {
-+					reg = <0>;
-+					label = "wan";
-+				};
-+
-+				port@1 {
-+					reg = <1>;
-+					label = "lan0";
-+				};
-+
-+				port@2 {
-+					reg = <2>;
-+					label = "lan1";
-+				};
-+
-+				port@3 {
-+					reg = <3>;
-+					label = "lan2";
-+				};
-+
-+				port@4 {
-+					reg = <4>;
-+					label = "lan3";
-+				};
-+
-+				port@6 {
-+					reg = <6>;
-+					label = "cpu";
-+					ethernet = <&gmac0>;
-+					phy-mode = "2500base-x";
-+
-+					fixed-link {
-+						speed = <2500>;
-+						full-duplex;
-+						pause;
-+					};
-+				};
-+			};
-+		};
-+
- 	};
- };
- 
diff --git a/target/linux/mediatek/patches-5.4/0900-bt-mtk-serial-fix.patch b/target/linux/mediatek/patches-5.4/0900-bt-mtk-serial-fix.patch
deleted file mode 100644
index 872b2bad45..0000000000
--- a/target/linux/mediatek/patches-5.4/0900-bt-mtk-serial-fix.patch
+++ /dev/null
@@ -1,33 +0,0 @@
---- a/drivers/tty/serial/8250/8250.h
-+++ b/drivers/tty/serial/8250/8250.h
-@@ -82,6 +82,7 @@ struct serial8250_config {
- #define UART_CAP_MINI	(1 << 17)	/* Mini UART on BCM283X family lacks:
- 					 * STOP PARITY EPAR SPAR WLEN5 WLEN6
- 					 */
-+#define UART_CAP_NMOD	(1 << 18)	/* UART doesn't do termios */
- 
- #define UART_BUG_QUOT	(1 << 0)	/* UART has buggy quot LSB */
- #define UART_BUG_TXEN	(1 << 1)	/* UART has buggy TX IIR status */
---- a/drivers/tty/serial/8250/8250_port.c
-+++ b/drivers/tty/serial/8250/8250_port.c
-@@ -290,7 +290,7 @@ static const struct serial8250_config ua
- 		.tx_loadsz	= 16,
- 		.fcr		= UART_FCR_ENABLE_FIFO |
- 				  UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
--		.flags		= UART_CAP_FIFO,
-+		.flags		= UART_CAP_FIFO | UART_CAP_NMOD,
- 	},
- 	[PORT_NPCM] = {
- 		.name		= "Nuvoton 16550",
-@@ -2597,6 +2597,11 @@ serial8250_do_set_termios(struct uart_po
- 	unsigned long flags;
- 	unsigned int baud, quot, frac = 0;
- 
-+	if (up->capabilities & UART_CAP_NMOD) {
-+		termios->c_cflag = 0;
-+		return;
-+	}
-+
- 	if (up->capabilities & UART_CAP_MINI) {
- 		termios->c_cflag &= ~(CSTOPB | PARENB | PARODD | CMSPAR);
- 		if ((termios->c_cflag & CSIZE) == CS5 ||
diff --git a/target/linux/mediatek/patches-5.4/0990-gsw-rtl8367s-mt7622-support.patch b/target/linux/mediatek/patches-5.4/0990-gsw-rtl8367s-mt7622-support.patch
deleted file mode 100644
index a3d49e903e..0000000000
--- a/target/linux/mediatek/patches-5.4/0990-gsw-rtl8367s-mt7622-support.patch
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -42,6 +42,12 @@ config MDIO_BCM_IPROC
- 	  This module provides a driver for the MDIO busses found in the
- 	  Broadcom iProc SoC's.
- 
-+config RTL8367S_GSW
-+	tristate "rtl8367 Gigabit Switch support for mt7622"
-+	depends on NET_VENDOR_MEDIATEK
-+	help
-+	  This driver supports rtl8367s in mt7622
-+
- config MDIO_BCM_UNIMAC
- 	tristate "Broadcom UniMAC MDIO bus controller"
- 	depends on HAS_IOMEM
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -110,4 +110,5 @@ obj-$(CONFIG_TERANETICS_PHY)	+= teraneti
- obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
- obj-$(CONFIG_XILINX_GMII2RGMII) += xilinx_gmii2rgmii.o
- obj-$(CONFIG_MT753X_GSW)        += mtk/mt753x/
-+obj-$(CONFIG_RTL8367S_GSW)	+= rtk/
- 
diff --git a/target/linux/mediatek/patches-5.4/0991-dt-bindings-PCI-Mediatek-Update-PCIe-binding.patch b/target/linux/mediatek/patches-5.4/0991-dt-bindings-PCI-Mediatek-Update-PCIe-binding.patch
deleted file mode 100644
index 02e4c130ea..0000000000
--- a/target/linux/mediatek/patches-5.4/0991-dt-bindings-PCI-Mediatek-Update-PCIe-binding.patch
+++ /dev/null
@@ -1,415 +0,0 @@
-From patchwork Thu May 28 06:16:45 2020
-Content-Type: text/plain; charset="utf-8"
-MIME-Version: 1.0
-Content-Transfer-Encoding: 7bit
-X-Patchwork-Submitter: Chuanjia Liu <chuanjia.liu@mediatek.com>
-X-Patchwork-Id: 11574793
-Return-Path: 
- <SRS0=ftSA=7K=lists.infradead.org=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@kernel.org>
-Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org
- [172.30.200.123])
-	by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 391201392
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:20:27 +0000 (UTC)
-Received: from bombadil.infradead.org (bombadil.infradead.org
- [198.137.202.133])
-	(using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits))
-	(No client certificate requested)
-	by mail.kernel.org (Postfix) with ESMTPS id 104F620657
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:20:27 +0000 (UTC)
-Authentication-Results: mail.kernel.org;
-	dkim=pass (2048-bit key) header.d=lists.infradead.org
- header.i=@lists.infradead.org header.b="raZHaWxs";
-	dkim=fail reason="signature verification failed" (1024-bit key)
- header.d=mediatek.com header.i=@mediatek.com header.b="YztrByG/"
-DMARC-Filter: OpenDMARC Filter v1.3.2 mail.kernel.org 104F620657
-Authentication-Results: mail.kernel.org;
- dmarc=fail (p=none dis=none) header.from=mediatek.com
-Authentication-Results: mail.kernel.org;
- spf=none
- smtp.mailfrom=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
-	d=lists.infradead.org; s=bombadil.20170209; h=Sender:
-	Content-Transfer-Encoding:Content-Type:Cc:List-Subscribe:List-Help:List-Post:
-	List-Archive:List-Unsubscribe:List-Id:MIME-Version:References:In-Reply-To:
-	Message-ID:Date:Subject:To:From:Reply-To:Content-ID:Content-Description:
-	Resent-Date:Resent-From:Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:
-	List-Owner; bh=aVtKU+Ey8KEM97+S66fz9ZMo+H8BP570jhAAvaRsNWc=; b=raZHaWxsfCxsrd
-	Byn/w1oLN/J82ApnNdBBXixq9Qj0uXIU2tBVqkiQ9lG6QDk7uguxQSJLeTqrsI/uxQmCI/PGQtZdP
-	sH0oboi2sbQSqJ/1ud4uL2pPaiLRJCxINF5oWjoZMsjn/b2fWvn52P6vTr/dxDTaabiVhY0HL0J+X
-	7YGc1aYtO76HZHE2ke3puR42QkI8hE9E2cEhiLWeuUiLdUBegNM5MdYftu4nJTcCXnAeJjp/wIpYG
-	7X737N9cmanDf6Bxr2bNPgaYzH+m7JK6eGxuAvWo0+PE9OX7MLrXY3KjixcjD/b0he0mfEM++gBAq
-	KBYKl5wh1mnlR2WIWXew==;
-Received: from localhost ([127.0.0.1] helo=bombadil.infradead.org)
-	by bombadil.infradead.org with esmtp (Exim 4.92.3 #3 (Red Hat Linux))
-	id 1jeBtx-0005JC-DJ; Thu, 28 May 2020 06:20:25 +0000
-Received: from mailgw01.mediatek.com ([216.200.240.184])
- by bombadil.infradead.org with esmtps (Exim 4.92.3 #3 (Red Hat Linux))
- id 1jeBtW-0002f2-75; Thu, 28 May 2020 06:20:01 +0000
-X-UUID: d5cb6d96c2a5421796c2f8a284ff3670-20200527
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
- d=mediatek.com;
- s=dk;
- h=Content-Transfer-Encoding:Content-Type:MIME-Version:References:In-Reply-To:Message-ID:Date:Subject:CC:To:From;
- bh=EqjC+5cHgv6eykN7FPf2mtwK9UivJ3XSCE0jEvb8h+8=;
- b=YztrByG/Ia304l9KDPBwoHFYkFCN6qBXPqwZgg56CA9VitadAg2+K1VgfEU+oHqsqcsGAMdZTRMQh17tpm4bJParw6MMzAQ28te2TcxvQMV8PZMkerJdZyyYblI7ybauPWuofAQgQMtuwSKVii8eTRJbf99OZ9vDGJP3zo2j1wU=;
-X-UUID: d5cb6d96c2a5421796c2f8a284ff3670-20200527
-Received: from mtkcas66.mediatek.inc [(172.29.193.44)] by
- mailgw01.mediatek.com
- (envelope-from <chuanjia.liu@mediatek.com>)
- (musrelay.mediatek.com ESMTP with TLS)
- with ESMTP id 681958707; Wed, 27 May 2020 22:20:16 -0800
-Received: from MTKMBS07N2.mediatek.inc (172.21.101.141) by
- MTKMBS62N1.mediatek.inc (172.29.193.41) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Wed, 27 May 2020 23:18:52 -0700
-Received: from mtkcas07.mediatek.inc (172.21.101.84) by
- mtkmbs07n2.mediatek.inc (172.21.101.141) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Thu, 28 May 2020 14:18:49 +0800
-Received: from localhost.localdomain (10.17.3.153) by mtkcas07.mediatek.inc
- (172.21.101.73) with Microsoft SMTP Server id 15.0.1497.2 via Frontend
- Transport; Thu, 28 May 2020 14:18:47 +0800
-From: <chuanjia.liu@mediatek.com>
-To: <robh+dt@kernel.org>, <ryder.lee@mediatek.com>, <matthias.bgg@gmail.com>
-Subject: [PATCH v2 1/4] dt-bindings: PCI: Mediatek: Update PCIe binding
-Date: Thu, 28 May 2020 14:16:45 +0800
-Message-ID: <20200528061648.32078-2-chuanjia.liu@mediatek.com>
-X-Mailer: git-send-email 2.18.0
-In-Reply-To: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-References: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-MIME-Version: 1.0
-X-MTK: N
-X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 
-X-CRM114-CacheID: sfid-20200527_231958_261064_608CC03E 
-X-CRM114-Status: GOOD (  13.95  )
-X-Spam-Score: -0.2 (/)
-X-Spam-Report: SpamAssassin version 3.4.4 on bombadil.infradead.org summary:
- Content analysis details:   (-0.2 points)
- pts rule name              description
- ---- ----------------------
- --------------------------------------------------
- -0.0 SPF_PASS               SPF: sender matches SPF record
- 0.0 SPF_HELO_NONE          SPF: HELO does not publish an SPF Record
- 0.0 MIME_BASE64_TEXT       RAW: Message text disguised using base64
- encoding
- -0.1 DKIM_VALID_AU          Message has a valid DKIM or DK signature from
- author's domain
- 0.1 DKIM_SIGNED            Message has a DKIM or DK signature,
- not necessarily
- valid
- -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature
- -0.1 DKIM_VALID_EF          Message has a valid DKIM or DK signature from
- envelope-from domain
- 0.0 UNPARSEABLE_RELAY      Informational: message has unparseable relay
- lines
-X-BeenThere: linux-mediatek@lists.infradead.org
-X-Mailman-Version: 2.1.29
-Precedence: list
-List-Id: <linux-mediatek.lists.infradead.org>
-List-Unsubscribe: <http://lists.infradead.org/mailman/options/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=unsubscribe>
-List-Archive: <http://lists.infradead.org/pipermail/linux-mediatek/>
-List-Post: <mailto:linux-mediatek@lists.infradead.org>
-List-Help: <mailto:linux-mediatek-request@lists.infradead.org?subject=help>
-List-Subscribe: <http://lists.infradead.org/mailman/listinfo/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=subscribe>
-Cc: devicetree@vger.kernel.org, lorenzo.pieralisi@arm.com,
- srv_heupstream@mediatek.com, "chuanjia.liu" <Chuanjia.Liu@mediatek.com>,
- linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
- jianjun.wang@mediatek.com, linux-mediatek@lists.infradead.org,
- yong.wu@mediatek.com, bhelgaas@google.com,
- linux-arm-kernel@lists.infradead.org, amurray@thegoodpenguin.co.uk
-Sender: "Linux-mediatek" <linux-mediatek-bounces@lists.infradead.org>
-Errors-To: 
- linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-
-From: "chuanjia.liu" <Chuanjia.Liu@mediatek.com>
-
-There are two independent PCIe controllers in MT2712/MT7622 platform,
-and each of them should contain an independent MSI domain.
-
-In current architecture, MSI domain will be inherited from the root
-bridge, and all of the devices will share the same MSI domain.
-Hence that, the PCIe devices will not work properly if the irq number
-which required is more than 32.
-
-Split the PCIe node for MT2712/MT7622 platform to fix MSI issue and
-comply with the hardware design.
-
-Signed-off-by: chuanjia.liu <Chuanjia.Liu@mediatek.com>
----
- .../bindings/pci/mediatek-pcie-cfg.yaml       |  38 +++++
- .../devicetree/bindings/pci/mediatek-pcie.txt | 144 +++++++++++-------
- 2 files changed, 129 insertions(+), 53 deletions(-)
- create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-cfg.yaml
-@@ -0,0 +1,38 @@
-+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
-+%YAML 1.2
-+---
-+$id: http://devicetree.org/schemas/pci/mediatek-pcie-cfg.yaml#
-+$schema: http://devicetree.org/meta-schemas/core.yaml#
-+
-+title: Mediatek PCIECFG controller
-+
-+maintainers:
-+  - Chuanjia Liu <chuanjia.liu@mediatek.com>
-+  - Jianjun Wang <jianjun.wang@mediatek.com>
-+
-+description: |
-+  The MediaTek PCIECFG controller controls some feature about
-+  LTSSM, ASPM and so on.
-+
-+properties:
-+  compatible:
-+      items:
-+        - enum:
-+            - mediatek,mt7622-pciecfg
-+            - mediatek,mt7629-pciecfg
-+        - const: syscon
-+
-+  reg:
-+    maxItems: 1
-+
-+required:
-+  - compatible
-+  - reg
-+
-+examples:
-+  - |
-+    pciecfg: pciecfg@1a140000 {
-+        compatible = "mediatek,mt7622-pciecfg", "syscon";
-+        reg = <0 0x1a140000 0 0x1000>;
-+    };
-+...
---- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
-+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
-@@ -8,7 +8,7 @@ Required properties:
- 	"mediatek,mt7623-pcie"
- 	"mediatek,mt7629-pcie"
- - device_type: Must be "pci"
--- reg: Base addresses and lengths of the PCIe subsys and root ports.
-+- reg: Base addresses and lengths of the root ports.
- - reg-names: Names of the above areas to use during resource lookup.
- - #address-cells: Address representation for root ports (must be 3)
- - #size-cells: Size representation for root ports (must be 2)
-@@ -19,10 +19,10 @@ Required properties:
-    - sys_ckN :transaction layer and data link layer clock
-   Required entries for MT2701/MT7623:
-    - free_ck :for reference clock of PCIe subsys
--  Required entries for MT2712/MT7622:
-+  Required entries for MT2712/MT7622/MT7629:
-    - ahb_ckN :AHB slave interface operating clock for CSR access and RC
- 	      initiated MMIO access
--  Required entries for MT7622:
-+  Required entries for MT7622/MT7629:
-    - axi_ckN :application layer MMIO channel operating clock
-    - aux_ckN :pe2_mac_bridge and pe2_mac_core operating clock when
- 	      pcie_mac_ck/pcie_pipe_ck is turned off
-@@ -47,10 +47,13 @@ Required properties for MT7623/MT2701:
- - reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the
-   number of root ports.
- 
--Required properties for MT2712/MT7622:
-+Required properties for MT2712/MT7622/MT7629:
- -interrupts: A list of interrupt outputs of the controller, must have one
- 	     entry for each PCIe port
- 
-+Required properties for MT7622/MT7629:
-+- mediatek,pcie-subsys: Should be a phandle of the pciecfg node.
-+
- In addition, the device tree node must have sub-nodes describing each
- PCIe port interface, having the following mandatory properties:
- 
-@@ -143,56 +146,73 @@ Examples for MT7623:
- 
- Examples for MT2712:
- 
--	pcie: pcie@11700000 {
-+	pcie1: pcie@112ff000 {
- 		compatible = "mediatek,mt2712-pcie";
- 		device_type = "pci";
--		reg = <0 0x11700000 0 0x1000>,
--		      <0 0x112ff000 0 0x1000>;
--		reg-names = "port0", "port1";
-+		reg = <0 0x112ff000 0 0x1000>;
-+		reg-names = "port1";
- 		#address-cells = <3>;
- 		#size-cells = <2>;
--		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
--			     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
--		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
--			 <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
--			 <&pericfg CLK_PERI_PCIE0>,
-+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-+		interrupt-names = "pcie_irq";
-+		clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
- 			 <&pericfg CLK_PERI_PCIE1>;
--		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1";
--		phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>;
--		phy-names = "pcie-phy0", "pcie-phy1";
-+		clock-names = "sys_ck1", "ahb_ck1";
-+		phys = <&u3port1 PHY_TYPE_PCIE>;
-+		phy-names = "pcie-phy1";
- 		bus-range = <0x00 0xff>;
--		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x10000000>;
-+		ranges = <0x82000000 0 0x11400000  0x0 0x11400000  0 0x300000>;
-+		status = "disabled";
- 
--		pcie0: pcie@0,0 {
--			reg = <0x0000 0 0 0 0>;
-+		slot1: pcie@1,0 {
-+			reg = <0x0800 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
- 			#interrupt-cells = <1>;
- 			ranges;
- 			interrupt-map-mask = <0 0 0 7>;
--			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
--					<0 0 0 2 &pcie_intc0 1>,
--					<0 0 0 3 &pcie_intc0 2>,
--					<0 0 0 4 &pcie_intc0 3>;
--			pcie_intc0: interrupt-controller {
-+			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
-+					<0 0 0 2 &pcie_intc1 1>,
-+					<0 0 0 3 &pcie_intc1 2>,
-+					<0 0 0 4 &pcie_intc1 3>;
-+			pcie_intc1: interrupt-controller {
- 				interrupt-controller;
- 				#address-cells = <0>;
- 				#interrupt-cells = <1>;
- 			};
- 		};
-+	};
- 
--		pcie1: pcie@1,0 {
--			reg = <0x0800 0 0 0 0>;
-+	pcie0: pcie@11700000 {
-+		compatible = "mediatek,mt2712-pcie";
-+		device_type = "pci";
-+		reg = <0 0x11700000 0 0x1000>;
-+		reg-names = "port0";
-+		#address-cells = <3>;
-+		#size-cells = <2>;
-+		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
-+		interrupt-names = "pcie_irq";
-+		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
-+			 <&pericfg CLK_PERI_PCIE0>;
-+		clock-names = "sys_ck0", "ahb_ck0";
-+		phys = <&u3port0 PHY_TYPE_PCIE>;
-+		phy-names = "pcie-phy0";
-+		bus-range = <0x00 0xff>;
-+		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x10000000>;
-+		status = "disabled";
-+
-+		slot0: pcie@0,0 {
-+			reg = <0x0000 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
- 			#interrupt-cells = <1>;
- 			ranges;
- 			interrupt-map-mask = <0 0 0 7>;
--			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
--					<0 0 0 2 &pcie_intc1 1>,
--					<0 0 0 3 &pcie_intc1 2>,
--					<0 0 0 4 &pcie_intc1 3>;
--			pcie_intc1: interrupt-controller {
-+			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
-+					<0 0 0 2 &pcie_intc0 1>,
-+					<0 0 0 3 &pcie_intc0 2>,
-+					<0 0 0 4 &pcie_intc0 3>;
-+			pcie_intc0: interrupt-controller {
- 				interrupt-controller;
- 				#address-cells = <0>;
- 				#interrupt-cells = <1>;
-@@ -202,39 +222,31 @@ Examples for MT2712:
- 
- Examples for MT7622:
- 
--	pcie: pcie@1a140000 {
-+	pcie0: pcie@1a143000 {
- 		compatible = "mediatek,mt7622-pcie";
- 		device_type = "pci";
--		reg = <0 0x1a140000 0 0x1000>,
--		      <0 0x1a143000 0 0x1000>,
--		      <0 0x1a145000 0 0x1000>;
--		reg-names = "subsys", "port0", "port1";
-+		reg = <0 0x1a143000 0 0x1000>;
-+		reg-names = "port0";
-+		mediatek,pcie-cfg = <&pciecfg>;
- 		#address-cells = <3>;
- 		#size-cells = <2>;
--		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>,
--			     <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-+		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
-+		interrupt-names = "pcie_irq";
- 		clocks = <&pciesys CLK_PCIE_P0_MAC_EN>,
--			 <&pciesys CLK_PCIE_P1_MAC_EN>,
- 			 <&pciesys CLK_PCIE_P0_AHB_EN>,
--			 <&pciesys CLK_PCIE_P1_AHB_EN>,
- 			 <&pciesys CLK_PCIE_P0_AUX_EN>,
--			 <&pciesys CLK_PCIE_P1_AUX_EN>,
- 			 <&pciesys CLK_PCIE_P0_AXI_EN>,
--			 <&pciesys CLK_PCIE_P1_AXI_EN>,
- 			 <&pciesys CLK_PCIE_P0_OBFF_EN>,
--			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
--			 <&pciesys CLK_PCIE_P0_PIPE_EN>,
--			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
--		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1",
--			      "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1",
--			      "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1";
--		phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>;
--		phy-names = "pcie-phy0", "pcie-phy1";
-+			 <&pciesys CLK_PCIE_P0_PIPE_EN>;
-+		clock-names = "sys_ck0", "ahb_ck0", "aux_ck0",
-+			      "axi_ck0", "obff_ck0", "pipe_ck0";
-+
- 		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
- 		bus-range = <0x00 0xff>;
--		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x10000000>;
-+		ranges = <0x82000000 0 0x20000000  0 0x20000000  0 0x8000000>;
-+		status = "disabled";
- 
--		pcie0: pcie@0,0 {
-+		slot0: pcie@0,0 {
- 			reg = <0x0000 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
-@@ -251,8 +263,34 @@ Examples for MT7622:
- 				#interrupt-cells = <1>;
- 			};
- 		};
-+	};
-+
-+	pcie1: pcie@1a145000 {
-+		compatible = "mediatek,mt7622-pcie";
-+		device_type = "pci";
-+		reg = <0 0x1a145000 0 0x1000>;
-+		reg-names = "port1";
-+		mediatek,pcie-cfg = <&pciecfg>;
-+		#address-cells = <3>;
-+		#size-cells = <2>;
-+		interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-+		interrupt-names = "pcie_irq";
-+		clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
-+			 /* designer has connect RC1 with p0_ahb clock */
-+			 <&pciesys CLK_PCIE_P0_AHB_EN>,
-+			 <&pciesys CLK_PCIE_P1_AUX_EN>,
-+			 <&pciesys CLK_PCIE_P1_AXI_EN>,
-+			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
-+			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
-+		clock-names = "sys_ck1", "ahb_ck1", "aux_ck1",
-+			      "axi_ck1", "obff_ck1", "pipe_ck1";
-+
-+		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
-+		bus-range = <0x00 0xff>;
-+		ranges = <0x82000000 0 0x28000000  0 0x28000000  0 0x8000000>;
-+		status = "disabled";
- 
--		pcie1: pcie@1,0 {
-+		slot1: pcie@1,0 {
- 			reg = <0x0800 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
diff --git a/target/linux/mediatek/patches-5.4/0992-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch b/target/linux/mediatek/patches-5.4/0992-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch
deleted file mode 100644
index 3e4d44f59e..0000000000
--- a/target/linux/mediatek/patches-5.4/0992-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch
+++ /dev/null
@@ -1,217 +0,0 @@
-From patchwork Thu May 28 06:16:46 2020
-Content-Type: text/plain; charset="utf-8"
-MIME-Version: 1.0
-Content-Transfer-Encoding: 7bit
-X-Patchwork-Submitter: Chuanjia Liu <chuanjia.liu@mediatek.com>
-X-Patchwork-Id: 11574781
-Return-Path: 
- <SRS0=ftSA=7K=lists.infradead.org=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@kernel.org>
-Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org
- [172.30.200.123])
-	by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 0A99B60D
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:19:04 +0000 (UTC)
-Received: from bombadil.infradead.org (bombadil.infradead.org
- [198.137.202.133])
-	(using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits))
-	(No client certificate requested)
-	by mail.kernel.org (Postfix) with ESMTPS id DCC99208FE
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:19:03 +0000 (UTC)
-Authentication-Results: mail.kernel.org;
-	dkim=pass (2048-bit key) header.d=lists.infradead.org
- header.i=@lists.infradead.org header.b="SpOi0ueF";
-	dkim=fail reason="signature verification failed" (1024-bit key)
- header.d=mediatek.com header.i=@mediatek.com header.b="UGIBoIEG"
-DMARC-Filter: OpenDMARC Filter v1.3.2 mail.kernel.org DCC99208FE
-Authentication-Results: mail.kernel.org;
- dmarc=fail (p=none dis=none) header.from=mediatek.com
-Authentication-Results: mail.kernel.org;
- spf=none
- smtp.mailfrom=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
-	d=lists.infradead.org; s=bombadil.20170209; h=Sender:
-	Content-Transfer-Encoding:Content-Type:Cc:List-Subscribe:List-Help:List-Post:
-	List-Archive:List-Unsubscribe:List-Id:MIME-Version:References:In-Reply-To:
-	Message-ID:Date:Subject:To:From:Reply-To:Content-ID:Content-Description:
-	Resent-Date:Resent-From:Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:
-	List-Owner; bh=LIr5poLUT/UdH6/akh/pnICGGa3rUBkN+4FhE1DyOrU=; b=SpOi0ueFcoJ/ka
-	4esa6cDd5oU4fp0z684ZVPaVvvhm/azSZBBMYinHaAW6EvzKcMNYIX9grP8eg/728lEPNTKVq0I8H
-	PQZ9KvD4uTu8Opo1hD8LsRSLr+YLpNKt3KPOY/4gpwQ97uU9rI5PwkuAxPBgR949Vh5EiG0Vaww1H
-	Ep+I5BFRn2LVVQZP1Z7U0A0VUcOTLJ4znoWRLEXxtM9/Wd4hwQsrEPQszeDFti/RbwGfJ5efOb5UL
-	fhwBzSxELEzAAgH7env/XD2sSSpVf2Qsn6WO8D3ZepMtWrRtARiaRKSNxSBQTg2SSHcjmBSJSzcX+
-	w8wqWaUMs0crlBuZWS1g==;
-Received: from localhost ([127.0.0.1] helo=bombadil.infradead.org)
-	by bombadil.infradead.org with esmtp (Exim 4.92.3 #3 (Red Hat Linux))
-	id 1jeBsc-0001tI-88; Thu, 28 May 2020 06:19:02 +0000
-Received: from mailgw01.mediatek.com ([216.200.240.184])
- by bombadil.infradead.org with esmtps (Exim 4.92.3 #3 (Red Hat Linux))
- id 1jeBsZ-0001rp-6g; Thu, 28 May 2020 06:19:01 +0000
-X-UUID: beeaf5765357439c91eab1f67ca7ef43-20200527
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
- d=mediatek.com;
- s=dk;
- h=Content-Transfer-Encoding:Content-Type:MIME-Version:References:In-Reply-To:Message-ID:Date:Subject:CC:To:From;
- bh=+IjWjsF/DhknqZB+lLSZ50cyvxDap+8w4tvqhp8Dv68=;
- b=UGIBoIEGJUuq5pEvYEad1HVGpiv6yma+94hva83D2gD8lYmihRWkpJxB2yn+dVtNm7ZXXoQBf+jvvULOmslJgs1HZTLJTnjpdvLmQqo42OXRXSVpTE49HdRkJZDAIWIAReBfOEkFgNxcIX3uedrtnww/NLJ2lagrYPG5ET4lI2E=;
-X-UUID: beeaf5765357439c91eab1f67ca7ef43-20200527
-Received: from mtkcas68.mediatek.inc [(172.29.94.19)] by mailgw01.mediatek.com
- (envelope-from <chuanjia.liu@mediatek.com>)
- (musrelay.mediatek.com ESMTP with TLS)
- with ESMTP id 603406343; Wed, 27 May 2020 22:19:17 -0800
-Received: from mtkmbs07n1.mediatek.inc (172.21.101.16) by
- MTKMBS62DR.mediatek.inc (172.29.94.18) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Wed, 27 May 2020 23:18:47 -0700
-Received: from mtkcas07.mediatek.inc (172.21.101.84) by
- mtkmbs07n1.mediatek.inc (172.21.101.16) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Thu, 28 May 2020 14:18:51 +0800
-Received: from localhost.localdomain (10.17.3.153) by mtkcas07.mediatek.inc
- (172.21.101.73) with Microsoft SMTP Server id 15.0.1497.2 via Frontend
- Transport; Thu, 28 May 2020 14:18:49 +0800
-From: <chuanjia.liu@mediatek.com>
-To: <robh+dt@kernel.org>, <ryder.lee@mediatek.com>, <matthias.bgg@gmail.com>
-Subject: [PATCH v2 2/4] PCI: mediatek: Use regmap to get shared pcie-cfg base
-Date: Thu, 28 May 2020 14:16:46 +0800
-Message-ID: <20200528061648.32078-3-chuanjia.liu@mediatek.com>
-X-Mailer: git-send-email 2.18.0
-In-Reply-To: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-References: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-MIME-Version: 1.0
-X-MTK: N
-X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 
-X-CRM114-CacheID: sfid-20200527_231859_251275_BED2B1E2 
-X-CRM114-Status: GOOD (  11.62  )
-X-Spam-Score: -0.2 (/)
-X-Spam-Report: SpamAssassin version 3.4.4 on bombadil.infradead.org summary:
- Content analysis details:   (-0.2 points)
- pts rule name              description
- ---- ----------------------
- --------------------------------------------------
- -0.0 SPF_PASS               SPF: sender matches SPF record
- 0.0 SPF_HELO_NONE          SPF: HELO does not publish an SPF Record
- 0.0 MIME_BASE64_TEXT       RAW: Message text disguised using base64
- encoding
- -0.1 DKIM_VALID_AU          Message has a valid DKIM or DK signature from
- author's domain
- 0.1 DKIM_SIGNED            Message has a DKIM or DK signature,
- not necessarily
- valid
- -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature
- -0.1 DKIM_VALID_EF          Message has a valid DKIM or DK signature from
- envelope-from domain
- 0.0 UNPARSEABLE_RELAY      Informational: message has unparseable relay
- lines
-X-BeenThere: linux-mediatek@lists.infradead.org
-X-Mailman-Version: 2.1.29
-Precedence: list
-List-Id: <linux-mediatek.lists.infradead.org>
-List-Unsubscribe: <http://lists.infradead.org/mailman/options/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=unsubscribe>
-List-Archive: <http://lists.infradead.org/pipermail/linux-mediatek/>
-List-Post: <mailto:linux-mediatek@lists.infradead.org>
-List-Help: <mailto:linux-mediatek-request@lists.infradead.org?subject=help>
-List-Subscribe: <http://lists.infradead.org/mailman/listinfo/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=subscribe>
-Cc: devicetree@vger.kernel.org, lorenzo.pieralisi@arm.com,
- srv_heupstream@mediatek.com, "chuanjia.liu" <Chuanjia.Liu@mediatek.com>,
- linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
- jianjun.wang@mediatek.com, linux-mediatek@lists.infradead.org,
- yong.wu@mediatek.com, bhelgaas@google.com,
- linux-arm-kernel@lists.infradead.org, amurray@thegoodpenguin.co.uk
-Sender: "Linux-mediatek" <linux-mediatek-bounces@lists.infradead.org>
-Errors-To: 
- linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-
-From: "chuanjia.liu" <Chuanjia.Liu@mediatek.com>
-
-Use regmap to get shared pcie-cfg base and change
-the method to get pcie irq.
-
-Signed-off-by: chuanjia.liu <Chuanjia.Liu@mediatek.com>
----
- drivers/pci/controller/pcie-mediatek.c | 25 ++++++++++++++++++-------
- 1 file changed, 18 insertions(+), 7 deletions(-)
-
---- a/drivers/pci/controller/pcie-mediatek.c
-+++ b/drivers/pci/controller/pcie-mediatek.c
-@@ -14,6 +14,7 @@
- #include <linux/irqchip/chained_irq.h>
- #include <linux/irqdomain.h>
- #include <linux/kernel.h>
-+#include <linux/mfd/syscon.h>
- #include <linux/msi.h>
- #include <linux/module.h>
- #include <linux/of_address.h>
-@@ -23,6 +24,7 @@
- #include <linux/phy/phy.h>
- #include <linux/platform_device.h>
- #include <linux/pm_runtime.h>
-+#include <linux/regmap.h>
- #include <linux/reset.h>
- 
- #include "../pci.h"
-@@ -205,6 +207,7 @@ struct mtk_pcie_port {
-  * struct mtk_pcie - PCIe host information
-  * @dev: pointer to PCIe device
-  * @base: IO mapped register base
-+ * @cfg: IO mapped register map for PCIe config
-  * @free_ck: free-run reference clock
-  * @mem: non-prefetchable memory resource
-  * @ports: pointer to PCIe port information
-@@ -214,6 +217,7 @@ struct mtk_pcie_port {
- struct mtk_pcie {
- 	struct device *dev;
- 	void __iomem *base;
-+	struct regmap *cfg;
- 	struct clk *free_ck;
- 
- 	struct resource mem;
-@@ -651,7 +655,7 @@ static int mtk_pcie_setup_irq(struct mtk
- 		return err;
- 	}
- 
--	port->irq = platform_get_irq(pdev, port->slot);
-+	port->irq = platform_get_irq_byname(pdev, "pcie_irq");
- 	irq_set_chained_handler_and_data(port->irq,
- 					 mtk_pcie_intr_handler, port);
- 
-@@ -666,12 +670,11 @@ static int mtk_pcie_startup_port_v2(stru
- 	u32 val;
- 	int err;
- 
--	/* MT7622 platforms need to enable LTSSM and ASPM from PCIe subsys */
--	if (pcie->base) {
--		val = readl(pcie->base + PCIE_SYS_CFG_V2);
--		val |= PCIE_CSR_LTSSM_EN(port->slot) |
--		       PCIE_CSR_ASPM_L1_EN(port->slot);
--		writel(val, pcie->base + PCIE_SYS_CFG_V2);
-+	/* MT7622/MT7629 platforms need to enable LTSSM and ASPM. */
-+	if (pcie->cfg) {
-+		val = PCIE_CSR_LTSSM_EN(port->slot) |
-+		      PCIE_CSR_ASPM_L1_EN(port->slot);
-+		regmap_update_bits(pcie->cfg, PCIE_SYS_CFG_V2, val, val);
- 	}
- 
- 	/* Assert all reset signals */
-@@ -977,6 +980,7 @@ static int mtk_pcie_subsys_powerup(struc
- 	struct device *dev = pcie->dev;
- 	struct platform_device *pdev = to_platform_device(dev);
- 	struct resource *regs;
-+	struct device_node *cfg_node;
- 	int err;
- 
- 	/* get shared registers, which are optional */
-@@ -989,6 +993,13 @@ static int mtk_pcie_subsys_powerup(struc
- 		}
- 	}
- 
-+	cfg_node = of_parse_phandle(dev->of_node, "mediatek,pcie-cfg", 0);
-+	if (cfg_node) {
-+		pcie->cfg = syscon_node_to_regmap(cfg_node);
-+		if (IS_ERR(pcie->cfg))
-+			return PTR_ERR(pcie->cfg);
-+	}
-+
- 	pcie->free_ck = devm_clk_get(dev, "free_ck");
- 	if (IS_ERR(pcie->free_ck)) {
- 		if (PTR_ERR(pcie->free_ck) == -EPROBE_DEFER)
diff --git a/target/linux/mediatek/patches-5.4/0993-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-MT7622.patch b/target/linux/mediatek/patches-5.4/0993-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-MT7622.patch
deleted file mode 100644
index 3c5558b606..0000000000
--- a/target/linux/mediatek/patches-5.4/0993-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-MT7622.patch
+++ /dev/null
@@ -1,417 +0,0 @@
-From patchwork Thu May 28 06:16:47 2020
-Content-Type: text/plain; charset="utf-8"
-MIME-Version: 1.0
-Content-Transfer-Encoding: 7bit
-X-Patchwork-Submitter: Chuanjia Liu <chuanjia.liu@mediatek.com>
-X-Patchwork-Id: 11574785
-Return-Path: 
- <SRS0=ftSA=7K=lists.infradead.org=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@kernel.org>
-Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org
- [172.30.200.123])
-	by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 933301391
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:19:16 +0000 (UTC)
-Received: from bombadil.infradead.org (bombadil.infradead.org
- [198.137.202.133])
-	(using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits))
-	(No client certificate requested)
-	by mail.kernel.org (Postfix) with ESMTPS id D19F02078C
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:19:15 +0000 (UTC)
-Authentication-Results: mail.kernel.org;
-	dkim=pass (2048-bit key) header.d=lists.infradead.org
- header.i=@lists.infradead.org header.b="s8K7t7DF";
-	dkim=fail reason="signature verification failed" (1024-bit key)
- header.d=mediatek.com header.i=@mediatek.com header.b="RhX81Iqp"
-DMARC-Filter: OpenDMARC Filter v1.3.2 mail.kernel.org D19F02078C
-Authentication-Results: mail.kernel.org;
- dmarc=fail (p=none dis=none) header.from=mediatek.com
-Authentication-Results: mail.kernel.org;
- spf=none
- smtp.mailfrom=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
-	d=lists.infradead.org; s=bombadil.20170209; h=Sender:
-	Content-Transfer-Encoding:Content-Type:Cc:List-Subscribe:List-Help:List-Post:
-	List-Archive:List-Unsubscribe:List-Id:MIME-Version:References:In-Reply-To:
-	Message-ID:Date:Subject:To:From:Reply-To:Content-ID:Content-Description:
-	Resent-Date:Resent-From:Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:
-	List-Owner; bh=NHyHqNMcE7LW10MwduOJoKiWe8cv+XayY+L6WDZeSu0=; b=s8K7t7DFh1iQ5w
-	eGvuMRgXEQv/YWRuSZRyX8lx8R2H9IuawEIgkhO6lEo6xv0VdsRuj8SptfoWg5afCItMhih373M21
-	6sUy3tEiuKGgklfxLU0reLEkaATkKRGLJDY3eSSs1mvZDrydKuZLDTka+YDGaiESlOhqMr95Nm6YM
-	yK8O00qTwSRPJUILRsBv1e/Kz8NRCmYhs56snABJkKeJ51NRAkb20R6qGTEd6UyBlz3jTVYwluLgF
-	bdqzywDT6+BNg/Agh6Zd+v2PpO4cmwCpGm62+3UUyZkfi/aQ4qZ/AFAfSQI+3ZBAgsKMC1PGifOi/
-	FgGxIvAUk6atBy7DAHuw==;
-Received: from localhost ([127.0.0.1] helo=bombadil.infradead.org)
-	by bombadil.infradead.org with esmtp (Exim 4.92.3 #3 (Red Hat Linux))
-	id 1jeBsn-00025C-EF; Thu, 28 May 2020 06:19:13 +0000
-Received: from mailgw01.mediatek.com ([216.200.240.184])
- by bombadil.infradead.org with esmtps (Exim 4.92.3 #3 (Red Hat Linux))
- id 1jeBsZ-0001s4-6j; Thu, 28 May 2020 06:19:01 +0000
-X-UUID: c6210e6371fa445db0ae40a8b8a7a0a1-20200527
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
- d=mediatek.com;
- s=dk;
- h=Content-Transfer-Encoding:Content-Type:MIME-Version:References:In-Reply-To:Message-ID:Date:Subject:CC:To:From;
- bh=X9AwTdbhpWmlWY4LjTm8KLq4Cca3YI9UnyCX3O0BAak=;
- b=RhX81Iqp0mWhBDyMQMFSEtt23+DGAWoin1SrFGP1bzp6GEtu38b2pK5RJVBshJtuxi/a1uMXZjeDsHJn02VGdNA07FrzZ7jq6YYEL+8cJs2DnhySmNElZazXPv2vKu9TWygfilTT24h/u8V/eszuRuhkdoUKWol8LwDlPl9gskg=;
-X-UUID: c6210e6371fa445db0ae40a8b8a7a0a1-20200527
-Received: from mtkcas68.mediatek.inc [(172.29.94.19)] by mailgw01.mediatek.com
- (envelope-from <chuanjia.liu@mediatek.com>)
- (musrelay.mediatek.com ESMTP with TLS)
- with ESMTP id 7561992; Wed, 27 May 2020 22:19:17 -0800
-Received: from mtkmbs07n1.mediatek.inc (172.21.101.16) by
- MTKMBS62DR.mediatek.inc (172.29.94.18) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Wed, 27 May 2020 23:18:47 -0700
-Received: from mtkcas07.mediatek.inc (172.21.101.84) by
- mtkmbs07n1.mediatek.inc (172.21.101.16) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Thu, 28 May 2020 14:18:52 +0800
-Received: from localhost.localdomain (10.17.3.153) by mtkcas07.mediatek.inc
- (172.21.101.73) with Microsoft SMTP Server id 15.0.1497.2 via Frontend
- Transport; Thu, 28 May 2020 14:18:51 +0800
-From: <chuanjia.liu@mediatek.com>
-To: <robh+dt@kernel.org>, <ryder.lee@mediatek.com>, <matthias.bgg@gmail.com>
-Subject: [PATCH v2 3/4] arm64: dts: mediatek: Split PCIe node for
- MT2712/MT7622
-Date: Thu, 28 May 2020 14:16:47 +0800
-Message-ID: <20200528061648.32078-4-chuanjia.liu@mediatek.com>
-X-Mailer: git-send-email 2.18.0
-In-Reply-To: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-References: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-MIME-Version: 1.0
-X-MTK: N
-X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 
-X-CRM114-CacheID: sfid-20200527_231859_253529_B6751C5A 
-X-CRM114-Status: GOOD (  12.20  )
-X-Spam-Score: -0.2 (/)
-X-Spam-Report: SpamAssassin version 3.4.4 on bombadil.infradead.org summary:
- Content analysis details:   (-0.2 points)
- pts rule name              description
- ---- ----------------------
- --------------------------------------------------
- -0.0 SPF_PASS               SPF: sender matches SPF record
- 0.0 SPF_HELO_NONE          SPF: HELO does not publish an SPF Record
- 0.0 MIME_BASE64_TEXT       RAW: Message text disguised using base64
- encoding
- -0.1 DKIM_VALID_AU          Message has a valid DKIM or DK signature from
- author's domain
- 0.1 DKIM_SIGNED            Message has a DKIM or DK signature,
- not necessarily
- valid
- -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature
- -0.1 DKIM_VALID_EF          Message has a valid DKIM or DK signature from
- envelope-from domain
- 0.0 UNPARSEABLE_RELAY      Informational: message has unparseable relay
- lines
-X-BeenThere: linux-mediatek@lists.infradead.org
-X-Mailman-Version: 2.1.29
-Precedence: list
-List-Id: <linux-mediatek.lists.infradead.org>
-List-Unsubscribe: <http://lists.infradead.org/mailman/options/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=unsubscribe>
-List-Archive: <http://lists.infradead.org/pipermail/linux-mediatek/>
-List-Post: <mailto:linux-mediatek@lists.infradead.org>
-List-Help: <mailto:linux-mediatek-request@lists.infradead.org?subject=help>
-List-Subscribe: <http://lists.infradead.org/mailman/listinfo/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=subscribe>
-Cc: devicetree@vger.kernel.org, lorenzo.pieralisi@arm.com,
- srv_heupstream@mediatek.com, "chuanjia.liu" <Chuanjia.Liu@mediatek.com>,
- linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
- jianjun.wang@mediatek.com, linux-mediatek@lists.infradead.org,
- yong.wu@mediatek.com, bhelgaas@google.com,
- linux-arm-kernel@lists.infradead.org, amurray@thegoodpenguin.co.uk
-Sender: "Linux-mediatek" <linux-mediatek-bounces@lists.infradead.org>
-Errors-To: 
- linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-
-From: "chuanjia.liu" <Chuanjia.Liu@mediatek.com>
-
-There are two independent PCIe controllers in MT2712/MT7622 platform,
-and each of them should contain an independent MSI domain.
-
-In current architecture, MSI domain will be inherited from the root
-bridge, and all of the devices will share the same MSI domain.
-Hence that, the PCIe devices will not work properly if the irq number
-which required is more than 32.
-
-Split the PCIe node for MT2712/MT7622 platform to fix MSI issue and
-comply with the hardware design.
-
-Signed-off-by: chuanjia.liu <Chuanjia.Liu@mediatek.com>
----
- arch/arm64/boot/dts/mediatek/mt2712e.dtsi     | 75 +++++++++++--------
- .../dts/mediatek/mt7622-bananapi-bpi-r64.dts  | 16 ++--
- arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts  |  6 +-
- arch/arm64/boot/dts/mediatek/mt7622.dtsi      | 68 +++++++++++------
- 4 files changed, 96 insertions(+), 69 deletions(-)
-
---- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
-+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
-@@ -791,60 +791,73 @@
- 		};
- 	};
- 
--	pcie: pcie@11700000 {
-+	pcie1: pcie@112ff000 {
- 		compatible = "mediatek,mt2712-pcie";
- 		device_type = "pci";
--		reg = <0 0x11700000 0 0x1000>,
--		      <0 0x112ff000 0 0x1000>;
--		reg-names = "port0", "port1";
-+		reg = <0 0x112ff000 0 0x1000>;
-+		reg-names = "port1";
- 		#address-cells = <3>;
- 		#size-cells = <2>;
--		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
--			     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
--		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
--			 <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
--			 <&pericfg CLK_PERI_PCIE0>,
-+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-+		interrupt-names = "pcie_irq";
-+		clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
- 			 <&pericfg CLK_PERI_PCIE1>;
--		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1";
--		phys = <&u3port0 PHY_TYPE_PCIE>, <&u3port1 PHY_TYPE_PCIE>;
--		phy-names = "pcie-phy0", "pcie-phy1";
-+		clock-names = "sys_ck1", "ahb_ck1";
-+		phys = <&u3port1 PHY_TYPE_PCIE>;
-+		phy-names = "pcie-phy1";
- 		bus-range = <0x00 0xff>;
--		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x10000000>;
-+		ranges = <0x82000000 0 0x11400000  0x0 0x11400000  0 0x300000>;
-+		status = "disabled";
- 
--		pcie0: pcie@0,0 {
--			device_type = "pci";
--			status = "disabled";
--			reg = <0x0000 0 0 0 0>;
-+		slot1: pcie@1,0 {
-+			reg = <0x0800 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
- 			#interrupt-cells = <1>;
- 			ranges;
- 			interrupt-map-mask = <0 0 0 7>;
--			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
--					<0 0 0 2 &pcie_intc0 1>,
--					<0 0 0 3 &pcie_intc0 2>,
--					<0 0 0 4 &pcie_intc0 3>;
--			pcie_intc0: interrupt-controller {
-+			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
-+					<0 0 0 2 &pcie_intc1 1>,
-+					<0 0 0 3 &pcie_intc1 2>,
-+					<0 0 0 4 &pcie_intc1 3>;
-+			pcie_intc1: interrupt-controller {
- 				interrupt-controller;
- 				#address-cells = <0>;
- 				#interrupt-cells = <1>;
- 			};
- 		};
-+	};
- 
--		pcie1: pcie@1,0 {
--			device_type = "pci";
--			status = "disabled";
--			reg = <0x0800 0 0 0 0>;
-+	pcie0: pcie@11700000 {
-+		compatible = "mediatek,mt2712-pcie";
-+		device_type = "pci";
-+		reg = <0 0x11700000 0 0x1000>;
-+		reg-names = "port0";
-+		#address-cells = <3>;
-+		#size-cells = <2>;
-+		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
-+		interrupt-names = "pcie_irq";
-+		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
-+			 <&pericfg CLK_PERI_PCIE0>;
-+		clock-names = "sys_ck0", "ahb_ck0";
-+		phys = <&u3port0 PHY_TYPE_PCIE>;
-+		phy-names = "pcie-phy0";
-+		bus-range = <0x00 0xff>;
-+		ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
-+		status = "disabled";
-+
-+		slot0: pcie@0,0 {
-+			reg = <0x0000 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
- 			#interrupt-cells = <1>;
- 			ranges;
- 			interrupt-map-mask = <0 0 0 7>;
--			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
--					<0 0 0 2 &pcie_intc1 1>,
--					<0 0 0 3 &pcie_intc1 2>,
--					<0 0 0 4 &pcie_intc1 3>;
--			pcie_intc1: interrupt-controller {
-+			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
-+					<0 0 0 2 &pcie_intc0 1>,
-+					<0 0 0 3 &pcie_intc0 2>,
-+					<0 0 0 4 &pcie_intc0 3>;
-+			pcie_intc0: interrupt-controller {
- 				interrupt-controller;
- 				#address-cells = <0>;
- 				#interrupt-cells = <1>;
---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-@@ -294,18 +294,16 @@
- 	};
- };
- 
--&pcie {
-+&pcie0 {
- 	pinctrl-names = "default";
--	pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;
-+	pinctrl-0 = <&pcie0_pins>;
- 	status = "okay";
-+};
- 
--	pcie@0,0 {
--		status = "okay";
--	};
--
--	pcie@1,0 {
--		status = "okay";
--	};
-+&pcie1 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pcie1_pins>;
-+	status = "okay";
- };
- 
- &pio {
---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-@@ -794,45 +794,41 @@
- 		#reset-cells = <1>;
- 	};
- 
--	pcie: pcie@1a140000 {
-+	pciecfg: pciecfg@1a140000 {
-+		compatible = "mediatek,mt7622-pciecfg", "syscon";
-+		reg = <0 0x1a140000 0 0x1000>;
-+	};
-+
-+	pcie0: pcie@1a143000 {
- 		compatible = "mediatek,mt7622-pcie";
- 		device_type = "pci";
--		reg = <0 0x1a140000 0 0x1000>,
--		      <0 0x1a143000 0 0x1000>,
--		      <0 0x1a145000 0 0x1000>;
--		reg-names = "subsys", "port0", "port1";
-+		reg = <0 0x1a143000 0 0x1000>;
-+		reg-names = "port0";
-+		mediatek,pcie-cfg = <&pciecfg>;
- 		#address-cells = <3>;
- 		#size-cells = <2>;
--		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>,
--			     <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-+		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
-+		interrupt-names = "pcie_irq";
- 		clocks = <&pciesys CLK_PCIE_P0_MAC_EN>,
--			 <&pciesys CLK_PCIE_P1_MAC_EN>,
--			 <&pciesys CLK_PCIE_P0_AHB_EN>,
- 			 <&pciesys CLK_PCIE_P0_AHB_EN>,
- 			 <&pciesys CLK_PCIE_P0_AUX_EN>,
--			 <&pciesys CLK_PCIE_P1_AUX_EN>,
- 			 <&pciesys CLK_PCIE_P0_AXI_EN>,
--			 <&pciesys CLK_PCIE_P1_AXI_EN>,
- 			 <&pciesys CLK_PCIE_P0_OBFF_EN>,
--			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
--			 <&pciesys CLK_PCIE_P0_PIPE_EN>,
--			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
--		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1",
--			      "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1",
--			      "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1";
-+			 <&pciesys CLK_PCIE_P0_PIPE_EN>;
-+		clock-names = "sys_ck0", "ahb_ck0", "aux_ck0",
-+			      "axi_ck0", "obff_ck0", "pipe_ck0";
-+
- 		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
- 		bus-range = <0x00 0xff>;
--		ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
-+		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x8000000>;
- 		status = "disabled";
- 
--		pcie0: pcie@0,0 {
-+		slot0: pcie@0,0 {
- 			reg = <0x0000 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
- 			#interrupt-cells = <1>;
- 			ranges;
--			status = "disabled";
--
- 			interrupt-map-mask = <0 0 0 7>;
- 			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
- 					<0 0 0 2 &pcie_intc0 1>,
-@@ -844,15 +840,39 @@
- 				#interrupt-cells = <1>;
- 			};
- 		};
-+	};
- 
--		pcie1: pcie@1,0 {
-+	pcie1: pcie@1a145000 {
-+		compatible = "mediatek,mt7622-pcie";
-+		device_type = "pci";
-+		reg = <0 0x1a145000 0 0x1000>;
-+		reg-names = "port1";
-+		mediatek,pcie-cfg = <&pciecfg>;
-+		#address-cells = <3>;
-+		#size-cells = <2>;
-+		interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-+		interrupt-names = "pcie_irq";
-+		clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
-+			 /* designer has connect RC1 with p0_ahb clock */
-+			 <&pciesys CLK_PCIE_P0_AHB_EN>,
-+			 <&pciesys CLK_PCIE_P1_AUX_EN>,
-+			 <&pciesys CLK_PCIE_P1_AXI_EN>,
-+			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
-+			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
-+		clock-names = "sys_ck1", "ahb_ck1", "aux_ck1",
-+			      "axi_ck1", "obff_ck1", "pipe_ck1";
-+
-+		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
-+		bus-range = <0x00 0xff>;
-+		ranges = <0x82000000 0 0x28000000  0x0 0x28000000  0 0x8000000>;
-+		status = "disabled";
-+
-+		slot1: pcie@1,0 {
- 			reg = <0x0800 0 0 0 0>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
- 			#interrupt-cells = <1>;
- 			ranges;
--			status = "disabled";
--
- 			interrupt-map-mask = <0 0 0 7>;
- 			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
- 					<0 0 0 2 &pcie_intc1 1>,
---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-@@ -254,18 +254,16 @@
- 	};
- };
- 
--&pcie {
-+&pcie0 {
- 	pinctrl-names = "default";
--	pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;
-+	pinctrl-0 = <&pcie0_pins>;
- 	status = "okay";
-+};
- 
--	pcie@0,0 {
--		status = "okay";
--	};
--
--	pcie@1,0 {
--		status = "okay";
--	};
-+&pcie1 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pcie1_pins>;
-+	status = "okay";
- };
- 
- &pio {
diff --git a/target/linux/mediatek/patches-5.4/0994-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch b/target/linux/mediatek/patches-5.4/0994-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch
deleted file mode 100644
index f166aa75de..0000000000
--- a/target/linux/mediatek/patches-5.4/0994-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch
+++ /dev/null
@@ -1,203 +0,0 @@
-From patchwork Thu May 28 06:16:48 2020
-Content-Type: text/plain; charset="utf-8"
-MIME-Version: 1.0
-Content-Transfer-Encoding: 7bit
-X-Patchwork-Submitter: Chuanjia Liu <chuanjia.liu@mediatek.com>
-X-Patchwork-Id: 11574797
-Return-Path: 
- <SRS0=ftSA=7K=lists.infradead.org=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@kernel.org>
-Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org
- [172.30.200.123])
-	by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 30A5E1392
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:29:05 +0000 (UTC)
-Received: from bombadil.infradead.org (bombadil.infradead.org
- [198.137.202.133])
-	(using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits))
-	(No client certificate requested)
-	by mail.kernel.org (Postfix) with ESMTPS id 08B6320721
-	for <patchwork-linux-mediatek@patchwork.kernel.org>;
- Thu, 28 May 2020 06:29:05 +0000 (UTC)
-Authentication-Results: mail.kernel.org;
-	dkim=pass (2048-bit key) header.d=lists.infradead.org
- header.i=@lists.infradead.org header.b="auhxDafY";
-	dkim=fail reason="signature verification failed" (1024-bit key)
- header.d=mediatek.com header.i=@mediatek.com header.b="Kj09Arxb"
-DMARC-Filter: OpenDMARC Filter v1.3.2 mail.kernel.org 08B6320721
-Authentication-Results: mail.kernel.org;
- dmarc=fail (p=none dis=none) header.from=mediatek.com
-Authentication-Results: mail.kernel.org;
- spf=none
- smtp.mailfrom=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
-	d=lists.infradead.org; s=bombadil.20170209; h=Sender:
-	Content-Transfer-Encoding:Content-Type:Cc:List-Subscribe:List-Help:List-Post:
-	List-Archive:List-Unsubscribe:List-Id:MIME-Version:References:In-Reply-To:
-	Message-ID:Date:Subject:To:From:Reply-To:Content-ID:Content-Description:
-	Resent-Date:Resent-From:Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:
-	List-Owner; bh=+QPxF1vlOH7StIZYuXJa3V40x8QVDxCLF9AFXHblB9M=; b=auhxDafYBeaUZO
-	aYp2KVO8Aie0v4tYtRwBon7hF+x55JwD78SAxQR2RsSvrlOo9cMYYby+ToUWflVUWQ60FapAl+w+l
-	nkEjIOrLBErHwxNOcsD8T5kjyCBMqlz4OMAQYUDNJ3fSugRlGhOtxkjCGd9ebB8N2Rvu6/U8P1A9n
-	P15mEQoc+RLonR1+9mBgwTEXErjsraxkimTD4Txsp4IvMs3UdsMkP+r3OT5S/p+Uj6O9ES0h7xIon
-	aL79KaVqRLHrfZxnrVwuGiecAiTp8qLy9clHuJU32NA6ZcXH1OnWipKApgp8Ck7ys80WPKaMrat9B
-	XuskJ63w13DZAbCVvuGQ==;
-Received: from localhost ([127.0.0.1] helo=bombadil.infradead.org)
-	by bombadil.infradead.org with esmtp (Exim 4.92.3 #3 (Red Hat Linux))
-	id 1jeC2J-00014n-M9; Thu, 28 May 2020 06:29:03 +0000
-Received: from mailgw02.mediatek.com ([216.200.240.185])
- by bombadil.infradead.org with esmtps (Exim 4.92.3 #3 (Red Hat Linux))
- id 1jeC2H-00013t-Li; Thu, 28 May 2020 06:29:03 +0000
-X-UUID: a4877c1586e64afeb2d6172e10605d2b-20200527
-DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed;
- d=mediatek.com;
- s=dk;
- h=Content-Transfer-Encoding:Content-Type:MIME-Version:References:In-Reply-To:Message-ID:Date:Subject:CC:To:From;
- bh=CIwcBFK1x0LbOjDt1BG6/knHFxDHRiqj8ov/jWEZDBY=;
- b=Kj09ArxbnLVTc9bpaVPT3jQrIVjhL87sSYyVF9dFypS976k78Ce9gZd0f4K3zAZbYZHYoQtuyOQ9TOeufQfgD+Cr+j5VR7pTdO2E1iXHFs/eQAz5gAjvjlK01z1JiunrLnn9dvIr6c1gEkjQHny0VpuZ1duxx79jwYusg/Nw6Wc=;
-X-UUID: a4877c1586e64afeb2d6172e10605d2b-20200527
-Received: from mtkcas66.mediatek.inc [(172.29.193.44)] by
- mailgw02.mediatek.com
- (envelope-from <chuanjia.liu@mediatek.com>)
- (musrelay.mediatek.com ESMTP with TLS)
- with ESMTP id 899663677; Wed, 27 May 2020 22:29:21 -0800
-Received: from MTKMBS07N2.mediatek.inc (172.21.101.141) by
- MTKMBS62DR.mediatek.inc (172.29.94.18) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Wed, 27 May 2020 23:18:50 -0700
-Received: from mtkcas07.mediatek.inc (172.21.101.84) by
- mtkmbs07n2.mediatek.inc (172.21.101.141) with Microsoft SMTP Server (TLS) id
- 15.0.1497.2; Thu, 28 May 2020 14:18:54 +0800
-Received: from localhost.localdomain (10.17.3.153) by mtkcas07.mediatek.inc
- (172.21.101.73) with Microsoft SMTP Server id 15.0.1497.2 via Frontend
- Transport; Thu, 28 May 2020 14:18:52 +0800
-From: <chuanjia.liu@mediatek.com>
-To: <robh+dt@kernel.org>, <ryder.lee@mediatek.com>, <matthias.bgg@gmail.com>
-Subject: [PATCH v2 4/4] ARM: dts: mediatek: Update mt7629 PCIe node
-Date: Thu, 28 May 2020 14:16:48 +0800
-Message-ID: <20200528061648.32078-5-chuanjia.liu@mediatek.com>
-X-Mailer: git-send-email 2.18.0
-In-Reply-To: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-References: <20200528061648.32078-1-chuanjia.liu@mediatek.com>
-MIME-Version: 1.0
-X-MTK: N
-X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 
-X-CRM114-CacheID: sfid-20200527_232901_719172_E5A99C62 
-X-CRM114-Status: GOOD (  11.61  )
-X-Spam-Score: -0.2 (/)
-X-Spam-Report: SpamAssassin version 3.4.4 on bombadil.infradead.org summary:
- Content analysis details:   (-0.2 points)
- pts rule name              description
- ---- ----------------------
- --------------------------------------------------
- -0.0 SPF_PASS               SPF: sender matches SPF record
- 0.0 SPF_HELO_NONE          SPF: HELO does not publish an SPF Record
- 0.0 MIME_BASE64_TEXT       RAW: Message text disguised using base64
- encoding
- -0.1 DKIM_VALID_AU          Message has a valid DKIM or DK signature from
- author's domain
- 0.1 DKIM_SIGNED            Message has a DKIM or DK signature,
- not necessarily
- valid
- -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature
- -0.1 DKIM_VALID_EF          Message has a valid DKIM or DK signature from
- envelope-from domain
- 0.0 UNPARSEABLE_RELAY      Informational: message has unparseable relay
- lines
-X-BeenThere: linux-mediatek@lists.infradead.org
-X-Mailman-Version: 2.1.29
-Precedence: list
-List-Id: <linux-mediatek.lists.infradead.org>
-List-Unsubscribe: <http://lists.infradead.org/mailman/options/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=unsubscribe>
-List-Archive: <http://lists.infradead.org/pipermail/linux-mediatek/>
-List-Post: <mailto:linux-mediatek@lists.infradead.org>
-List-Help: <mailto:linux-mediatek-request@lists.infradead.org?subject=help>
-List-Subscribe: <http://lists.infradead.org/mailman/listinfo/linux-mediatek>,
- <mailto:linux-mediatek-request@lists.infradead.org?subject=subscribe>
-Cc: devicetree@vger.kernel.org, lorenzo.pieralisi@arm.com,
- srv_heupstream@mediatek.com, "chuanjia.liu" <Chuanjia.Liu@mediatek.com>,
- linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
- jianjun.wang@mediatek.com, linux-mediatek@lists.infradead.org,
- yong.wu@mediatek.com, bhelgaas@google.com,
- linux-arm-kernel@lists.infradead.org, amurray@thegoodpenguin.co.uk
-Sender: "Linux-mediatek" <linux-mediatek-bounces@lists.infradead.org>
-Errors-To: 
- linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org
-
-From: "chuanjia.liu" <Chuanjia.Liu@mediatek.com>
-
-Remove unused property and add pciecfg node.
-
-Signed-off-by: chuanjia.liu <Chuanjia.Liu@mediatek.com>
----
- arch/arm/boot/dts/mt7629-rfb.dts |  3 ++-
- arch/arm/boot/dts/mt7629.dtsi    | 23 +++++++++++++----------
- 2 files changed, 15 insertions(+), 11 deletions(-)
-
---- a/arch/arm/boot/dts/mt7629-rfb.dts
-+++ b/arch/arm/boot/dts/mt7629-rfb.dts
-@@ -176,9 +176,10 @@
- 	};
- };
- 
--&pcie {
-+&pcie1 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pcie_pins>;
-+	status = "okay";
- };
- 
- &pciephy1 {
---- a/arch/arm/boot/dts/mt7629.dtsi
-+++ b/arch/arm/boot/dts/mt7629.dtsi
-@@ -368,16 +368,21 @@
- 			#reset-cells = <1>;
- 		};
- 
--		pcie: pcie@1a140000 {
-+		pciecfg: pciecfg@1a140000 {
-+			compatible = "mediatek,mt7629-pciecfg", "syscon";
-+			reg = <0x1a140000 0x1000>;
-+		};
-+
-+		pcie1: pcie@1a145000 {
- 			compatible = "mediatek,mt7629-pcie";
- 			device_type = "pci";
--			reg = <0x1a140000 0x1000>,
--			      <0x1a145000 0x1000>;
--			reg-names = "subsys","port1";
-+			reg = <0x1a145000 0x1000>;
-+			reg-names = "port1";
-+			mediatek,pcie-cfg = <&pciecfg>;
- 			#address-cells = <3>;
- 			#size-cells = <2>;
--			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_LOW>,
--				     <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-+			interrupt-names = "pcie_irq";
- 			clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
- 				 <&pciesys CLK_PCIE_P0_AHB_EN>,
- 				 <&pciesys CLK_PCIE_P1_AUX_EN>,
-@@ -398,21 +403,19 @@
- 			power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
- 			bus-range = <0x00 0xff>;
- 			ranges = <0x82000000 0 0x20000000 0x20000000 0 0x10000000>;
-+			status = "disabled";
- 
--			pcie1: pcie@1,0 {
--				device_type = "pci";
-+			slot1: pcie@1,0 {
- 				reg = <0x0800 0 0 0 0>;
- 				#address-cells = <3>;
- 				#size-cells = <2>;
- 				#interrupt-cells = <1>;
- 				ranges;
--				num-lanes = <1>;
- 				interrupt-map-mask = <0 0 0 7>;
- 				interrupt-map = <0 0 0 1 &pcie_intc1 0>,
- 						<0 0 0 2 &pcie_intc1 1>,
- 						<0 0 0 3 &pcie_intc1 2>,
- 						<0 0 0 4 &pcie_intc1 3>;
--
- 				pcie_intc1: interrupt-controller {
- 					interrupt-controller;
- 					#address-cells = <0>;
diff --git a/target/linux/mediatek/patches-5.4/1003-dts-mt7622-rfb-change-to-ax-mtd-layout.patch b/target/linux/mediatek/patches-5.4/1003-dts-mt7622-rfb-change-to-ax-mtd-layout.patch
deleted file mode 100644
index 74a294f098..0000000000
--- a/target/linux/mediatek/patches-5.4/1003-dts-mt7622-rfb-change-to-ax-mtd-layout.patch
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
-@@ -589,17 +589,17 @@
- 
- 			factory: partition@1c0000 {
- 				label = "Factory";
--				reg = <0x1c0000 0x0040000>;
-+				reg = <0x1c0000 0x0100000>;
- 			};
- 
- 			partition@200000 {
- 				label = "firmware";
--				reg = <0x200000 0x2000000>;
-+				reg = <0x2c0000 0x2000000>;
- 			};
- 
- 			partition@2200000 {
- 				label = "User_data";
--				reg = <0x2200000 0x4000000>;
-+				reg = <0x22c0000 0x4000000>;
- 			};
- 		};
- 	};
diff --git a/target/linux/mediatek/patches-5.4/1010-pcie-mediatek-fix-clearing-interrupt-status.patch b/target/linux/mediatek/patches-5.4/1010-pcie-mediatek-fix-clearing-interrupt-status.patch
deleted file mode 100644
index d3ef78dc72..0000000000
--- a/target/linux/mediatek/patches-5.4/1010-pcie-mediatek-fix-clearing-interrupt-status.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From: Felix Fietkau <nbd@nbd.name>
-Date: Fri, 4 Sep 2020 18:33:27 +0200
-Subject: [PATCH] pcie-mediatek: fix clearing interrupt status
-
-Clearing the status needs to happen after running the handler, otherwise
-we will get an extra spurious interrupt after the cause has been cleared
-
-Signed-off-by: Felix Fietkau <nbd@nbd.name>
----
-
---- a/drivers/pci/controller/pcie-mediatek.c
-+++ b/drivers/pci/controller/pcie-mediatek.c
-@@ -616,10 +616,10 @@ static void mtk_pcie_intr_handler(struct
- 	if (status & INTX_MASK) {
- 		for_each_set_bit_from(bit, &status, PCI_NUM_INTX + INTX_SHIFT) {
- 			/* Clear the INTx */
--			writel(1 << bit, port->base + PCIE_INT_STATUS);
- 			virq = irq_find_mapping(port->irq_domain,
- 						bit - INTX_SHIFT);
- 			generic_handle_irq(virq);
-+			writel(1 << bit, port->base + PCIE_INT_STATUS);
- 		}
- 	}
- 
diff --git a/target/linux/mediatek/patches-5.4/1011-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch b/target/linux/mediatek/patches-5.4/1011-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch
deleted file mode 100644
index 3f7660b14b..0000000000
--- a/target/linux/mediatek/patches-5.4/1011-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch
+++ /dev/null
@@ -1,85 +0,0 @@
-From: Felix Fietkau <nbd@nbd.name>
-Date: Fri, 4 Sep 2020 18:36:06 +0200
-Subject: [PATCH] net: ethernet: mtk_eth_soc: add support for coherent DMA
-
-It improves performance by eliminating the need for a cache flush on rx and tx
-
-Signed-off-by: Felix Fietkau <nbd@nbd.name>
----
-
---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-@@ -357,7 +357,7 @@
- 		};
- 
- 		cci_control2: slave-if@5000 {
--			compatible = "arm,cci-400-ctrl-if";
-+			compatible = "arm,cci-400-ctrl-if", "syscon";
- 			interface-type = "ace";
- 			reg = <0x5000 0x1000>;
- 		};
-@@ -969,6 +969,8 @@
- 		power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>;
- 		mediatek,ethsys = <&ethsys>;
- 		mediatek,sgmiisys = <&sgmiisys>;
-+		mediatek,cci-control = <&cci_control2>;
-+		dma-coherent;
- 		#address-cells = <1>;
- 		#size-cells = <0>;
- 		status = "disabled";
---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
-+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
-@@ -9,6 +9,7 @@
- #include <linux/of_device.h>
- #include <linux/of_mdio.h>
- #include <linux/of_net.h>
-+#include <linux/of_address.h>
- #include <linux/mfd/syscon.h>
- #include <linux/regmap.h>
- #include <linux/clk.h>
-@@ -2506,6 +2507,13 @@ static int mtk_hw_init(struct mtk_eth *e
- 	if (ret)
- 		goto err_disable_pm;
- 
-+	if (of_dma_is_coherent(eth->dev->of_node)) {
-+		u32 mask = ETHSYS_DMA_AG_MAP_PDMA | ETHSYS_DMA_AG_MAP_QDMA |
-+			   ETHSYS_DMA_AG_MAP_PPE;
-+
-+		regmap_update_bits(eth->ethsys, ETHSYS_DMA_AG_MAP, mask, mask);
-+	}
-+
- 	if (MTK_HAS_CAPS(eth->soc->caps, MTK_SOC_MT7628)) {
- 		ret = device_reset(eth->dev);
- 		if (ret) {
-@@ -3101,6 +3109,16 @@ static int mtk_probe(struct platform_dev
- 		}
- 	}
- 
-+	if (of_dma_is_coherent(pdev->dev.of_node)) {
-+		struct regmap *cci;
-+
-+		cci = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
-+						      "mediatek,cci-control");
-+		/* enable CPU/bus coherency */
-+		if (!IS_ERR(cci))
-+			regmap_write(cci, 0, 3);
-+	}
-+
- 	if (MTK_HAS_CAPS(eth->soc->caps, MTK_SGMII)) {
- 		eth->sgmii = devm_kzalloc(eth->dev, sizeof(*eth->sgmii),
- 					  GFP_KERNEL);
---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
-+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
-@@ -448,6 +448,12 @@
- #define RSTCTRL_FE		BIT(6)
- #define RSTCTRL_PPE		BIT(31)
- 
-+/* ethernet dma channel agent map */
-+#define ETHSYS_DMA_AG_MAP	0x408
-+#define ETHSYS_DMA_AG_MAP_PDMA	BIT(0)
-+#define ETHSYS_DMA_AG_MAP_QDMA	BIT(1)
-+#define ETHSYS_DMA_AG_MAP_PPE	BIT(2)
-+
- /* SGMII subsystem config registers */
- /* Register to auto-negotiation restart */
- #define SGMSYS_PCS_CONTROL_1	0x0
diff --git a/target/linux/mediatek/patches-5.4/1012-pci-pcie-mediatek-add-support-for-coherent-DMA.patch b/target/linux/mediatek/patches-5.4/1012-pci-pcie-mediatek-add-support-for-coherent-DMA.patch
deleted file mode 100644
index 20a67676e3..0000000000
--- a/target/linux/mediatek/patches-5.4/1012-pci-pcie-mediatek-add-support-for-coherent-DMA.patch
+++ /dev/null
@@ -1,108 +0,0 @@
-From: Felix Fietkau <nbd@nbd.name>
-Date: Fri, 4 Sep 2020 18:42:42 +0200
-Subject: [PATCH] pci: pcie-mediatek: add support for coherent DMA
-
-It improves performance by eliminating the need for a cache flush for DMA on
-attached devices
-
-Signed-off-by: Felix Fietkau <nbd@nbd.name>
----
-
---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
-@@ -805,6 +805,8 @@
- 		reg = <0 0x1a143000 0 0x1000>;
- 		reg-names = "port0";
- 		mediatek,pcie-cfg = <&pciecfg>;
-+		mediatek,hifsys = <&hifsys>;
-+		mediatek,cci-control = <&cci_control2>;
- 		#address-cells = <3>;
- 		#size-cells = <2>;
- 		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
-@@ -822,6 +824,7 @@
- 		bus-range = <0x00 0xff>;
- 		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x8000000>;
- 		status = "disabled";
-+		dma-coherent;
- 
- 		slot0: pcie@0,0 {
- 			reg = <0x0000 0 0 0 0>;
-@@ -848,6 +851,8 @@
- 		reg = <0 0x1a145000 0 0x1000>;
- 		reg-names = "port1";
- 		mediatek,pcie-cfg = <&pciecfg>;
-+		mediatek,hifsys = <&hifsys>;
-+		mediatek,cci-control = <&cci_control2>;
- 		#address-cells = <3>;
- 		#size-cells = <2>;
- 		interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-@@ -866,6 +871,7 @@
- 		bus-range = <0x00 0xff>;
- 		ranges = <0x82000000 0 0x28000000  0x0 0x28000000  0 0x8000000>;
- 		status = "disabled";
-+		dma-coherent;
- 
- 		slot1: pcie@1,0 {
- 			reg = <0x0800 0 0 0 0>;
-@@ -925,6 +931,11 @@
- 		};
- 	};
- 
-+	hifsys: syscon@1af00000 {
-+		compatible = "mediatek,mt7622-hifsys", "syscon";
-+		reg = <0 0x1af00000 0 0x70>;
-+	};
-+
- 	ethsys: syscon@1b000000 {
- 		compatible = "mediatek,mt7622-ethsys",
- 			     "syscon";
---- a/drivers/pci/controller/pcie-mediatek.c
-+++ b/drivers/pci/controller/pcie-mediatek.c
-@@ -20,6 +20,7 @@
- #include <linux/of_address.h>
- #include <linux/of_pci.h>
- #include <linux/of_platform.h>
-+#include <linux/of_address.h>
- #include <linux/pci.h>
- #include <linux/phy/phy.h>
- #include <linux/platform_device.h>
-@@ -139,6 +140,11 @@
- #define PCIE_LINK_STATUS_V2	0x804
- #define PCIE_PORT_LINKUP_V2	BIT(10)
- 
-+/* DMA channel mapping */
-+#define HIFSYS_DMA_AG_MAP	0x008
-+#define HIFSYS_DMA_AG_MAP_PCIE0	BIT(0)
-+#define HIFSYS_DMA_AG_MAP_PCIE1	BIT(1)
-+
- struct mtk_pcie_port;
- 
- /**
-@@ -1068,6 +1074,27 @@ static int mtk_pcie_setup(struct mtk_pci
- 		}
- 	}
- 
-+	if (of_dma_is_coherent(node)) {
-+		struct regmap *con;
-+		u32 mask;
-+
-+		con = syscon_regmap_lookup_by_phandle(node,
-+						      "mediatek,cci-control");
-+		/* enable CPU/bus coherency */
-+		if (!IS_ERR(con))
-+			regmap_write(con, 0, 3);
-+
-+		con = syscon_regmap_lookup_by_phandle(node,
-+						      "mediatek,hifsys");
-+		if (IS_ERR(con)) {
-+			dev_err(dev, "missing hifsys node\n");
-+			return PTR_ERR(con);
-+		}
-+
-+		mask = HIFSYS_DMA_AG_MAP_PCIE0 | HIFSYS_DMA_AG_MAP_PCIE1;
-+		regmap_update_bits(con, HIFSYS_DMA_AG_MAP, mask, mask);
-+	}
-+
- 	for_each_available_child_of_node(node, child) {
- 		int slot;
- 
diff --git a/target/linux/mediatek/patches-5.4/1020-spi-nor-w25q512jv.patch b/target/linux/mediatek/patches-5.4/1020-spi-nor-w25q512jv.patch
deleted file mode 100644
index a234555556..0000000000
--- a/target/linux/mediatek/patches-5.4/1020-spi-nor-w25q512jv.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From: David Bauer <mail@david-bauer.net>
-Date: Thu, 11 Feb 2021 19:57:26 +0100
-Subject: [PATCH] mtd: spi-nor: add support for Winbond W25Q512
-
-The Winbond W25Q512 is a 512mb SPI-NOR chip. It supports 4K sectors as
-well as block protection and Dual-/Quad-read.
-
-Tested on: Ubiquiti UniFi 6 LR
-
-Signed-off-by: David Bauer <mail@david-bauer.net>
-
-Ref: https://patchwork.ozlabs.org/project/linux-mtd/patch/20210213151047.11700-1-mail@david-bauer.net/
-
---- a/drivers/mtd/spi-nor/spi-nor.c
-+++ b/drivers/mtd/spi-nor/spi-nor.c
-@@ -2552,6 +2552,9 @@ static const struct flash_info spi_nor_i
- 			  .fixups = &w25q256_fixups },
- 	{ "w25q256jvm", INFO(0xef7019, 0, 64 * 1024, 512,
- 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+	{ "w25q512jv", INFO(0xef4020, 0, 64 * 1024, 1024,
-+			SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ |
-+			SPI_NOR_HAS_TB | SPI_NOR_HAS_LOCK) },
- 	{ "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
- 			SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
- 
diff --git a/target/linux/mediatek/patches-5.4/1021-ubnt-ledbar-driver.patch b/target/linux/mediatek/patches-5.4/1021-ubnt-ledbar-driver.patch
deleted file mode 100644
index 41ab094e9f..0000000000
--- a/target/linux/mediatek/patches-5.4/1021-ubnt-ledbar-driver.patch
+++ /dev/null
@@ -1,29 +0,0 @@
---- a/drivers/leds/Kconfig
-+++ b/drivers/leds/Kconfig
-@@ -824,6 +824,16 @@ config LEDS_LM36274
- 	  Say Y to enable the LM36274 LED driver for TI LMU devices.
- 	  This supports the LED device LM36274.
- 
-+config LEDS_UBNT_LEDBAR
-+	tristate "LED support for Ubiquiti UniFi 6 LR"
-+	depends on LEDS_CLASS && I2C && OF
-+	help
-+	  This option enables support for the Ubiquiti LEDBAR
-+	  LED driver.
-+
-+	  To compile this driver as a module, choose M here: the module
-+	  will be called leds-ubnt-ledbar.
-+
- comment "LED Triggers"
- source "drivers/leds/trigger/Kconfig"
- 
---- a/drivers/leds/Makefile
-+++ b/drivers/leds/Makefile
-@@ -85,6 +85,7 @@ obj-$(CONFIG_LEDS_LM3601X)		+= leds-lm36
- obj-$(CONFIG_LEDS_TI_LMU_COMMON)	+= leds-ti-lmu-common.o
- obj-$(CONFIG_LEDS_LM3697)		+= leds-lm3697.o
- obj-$(CONFIG_LEDS_LM36274)		+= leds-lm36274.o
-+obj-$(CONFIG_LEDS_UBNT_LEDBAR)	+= leds-ubnt-ledbar.o
- 
- # LED SPI Drivers
- obj-$(CONFIG_LEDS_CR0014114)		+= leds-cr0014114.o
diff --git a/target/linux/mediatek/patches-5.4/115-dts-bpi64-add-snand-support.patch b/target/linux/mediatek/patches-5.4/115-dts-bpi64-add-snand-support.patch
deleted file mode 100644
index 4d369cefef..0000000000
--- a/target/linux/mediatek/patches-5.4/115-dts-bpi64-add-snand-support.patch
+++ /dev/null
@@ -1,57 +0,0 @@
---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
-@@ -108,7 +108,7 @@
- };
- 
- &bch {
--	status = "disabled";
-+	status = "okay";
- };
- 
- &btif {
-@@ -283,14 +283,40 @@
- 	status = "disabled";
- };
- 
--&nor_flash {
-+&snfi {
- 	pinctrl-names = "default";
--	pinctrl-0 = <&spi_nor_pins>;
--	status = "disabled";
-+	pinctrl-0 = <&serial_nand_pins>;
-+	status = "okay";
- 
--	flash@0 {
--		compatible = "jedec,spi-nor";
-+	snand: spi_nand@0 {
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		compatible = "spi-nand";
-+		spi-max-frequency = <104000000>;
- 		reg = <0>;
-+
-+		partitions {
-+			compatible = "fixed-partitions";
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+
-+			partition@0 {
-+				label = "bl2";
-+				reg = <0x0 0x80000>;
-+				read-only;
-+			};
-+
-+			partition@80000 {
-+				label = "fip";
-+				reg = <0x80000 0x200000>;
-+				read-only;
-+			};
-+
-+			partition@280000 {
-+				label = "ubi";
-+				reg = <0x280000 0x7d80000>;
-+			};
-+		};
- 	};
- };
-