diff options
| -rw-r--r-- | package/boot/uboot-sunxi/patches/301-sunxi-add-orangepi-R1-defconfig.patch | 48 | ||||
| -rw-r--r-- | package/boot/uboot-sunxi/patches/320-sunxi-Add-support-for-Orange-Pi-R1.patch (renamed from package/boot/uboot-sunxi/patches/300-sunxi-add-device-tree-for-Orange-Pi-R1-board.patch) | 171 |
2 files changed, 73 insertions, 146 deletions
diff --git a/package/boot/uboot-sunxi/patches/301-sunxi-add-orangepi-R1-defconfig.patch b/package/boot/uboot-sunxi/patches/301-sunxi-add-orangepi-R1-defconfig.patch deleted file mode 100644 index 6240fe3f57..0000000000 --- a/package/boot/uboot-sunxi/patches/301-sunxi-add-orangepi-R1-defconfig.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 231201c71b902b5999ed9b143f2a54674cfae88a Mon Sep 17 00:00:00 2001 -From: Hauke Mehrtens <hauke@hauke-m.de> -Date: Tue, 26 Sep 2017 22:17:33 +0200 -Subject: sunxi: add orangepi R1 defconfig - -Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> ---- - board/sunxi/MAINTAINERS | 5 +++++ - configs/orangepi_r1_defconfig | 19 +++++++++++++++++++ - 2 files changed, 24 insertions(+) - create mode 100644 configs/orangepi_r1_defconfig - ---- a/board/sunxi/MAINTAINERS -+++ b/board/sunxi/MAINTAINERS -@@ -302,6 +302,11 @@ M: Jagan Teki <jagan@amarulasolutions.co - S: Maintained - F: configs/orangepi_prime_defconfig - -+ORANGEPI R1 BOARD -+M: Hauke Mehrtens <hauke@hauke-m.de> -+S: Maintained -+F: configs/orangepi_r1_defconfig -+ - PINE64 BOARDS - M: Andre Przywara <andre.przywara@arm.com> - S: Maintained ---- /dev/null -+++ b/configs/orangepi_r1_defconfig -@@ -0,0 +1,19 @@ -+CONFIG_ARM=y -+CONFIG_ARCH_SUNXI=y -+CONFIG_SPL_SPI_FLASH_SUPPORT=y -+CONFIG_MACH_SUN8I_H3=y -+CONFIG_DRAM_CLK=624 -+CONFIG_DRAM_ZQ=3881979 -+CONFIG_DRAM_ODT_EN=y -+# CONFIG_VIDEO_DE2 is not set -+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-orangepi-r1" -+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -+CONFIG_CONSOLE_MUX=y -+CONFIG_SPL=y -+# CONFIG_CMD_IMLS is not set -+# CONFIG_CMD_FLASH is not set -+# CONFIG_CMD_FPGA is not set -+CONFIG_SPL_SPI_SUNXI=y -+CONFIG_SUN8I_EMAC=y -+CONFIG_USB_EHCI_HCD=y -+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y diff --git a/package/boot/uboot-sunxi/patches/300-sunxi-add-device-tree-for-Orange-Pi-R1-board.patch b/package/boot/uboot-sunxi/patches/320-sunxi-Add-support-for-Orange-Pi-R1.patch index 65ae63c64d..af459823ee 100644 --- a/package/boot/uboot-sunxi/patches/300-sunxi-add-device-tree-for-Orange-Pi-R1-board.patch +++ b/package/boot/uboot-sunxi/patches/320-sunxi-Add-support-for-Orange-Pi-R1.patch @@ -1,14 +1,20 @@ -From 1f92596cc520f760589289059a5aa739366dd19c Mon Sep 17 00:00:00 2001 +From 068fb0d5728c5ec93cb961718d59e7c718886edd Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens <hauke@hauke-m.de> Date: Tue, 26 Sep 2017 22:16:59 +0200 -Subject: sunxi: add device tree for Orange Pi R1 board +Subject: sunxi: Add support for Orange Pi R1 + +The device tree files are also submitted for inclusion into the Linux +kernel. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> --- - arch/arm/dts/Makefile | 1 + - arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts | 157 +++++++++++++++++++++++++++++ - 2 files changed, 158 insertions(+) + arch/arm/dts/Makefile | 1 + + arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts | 77 ++++++++++++++++++++++++++++++ + board/sunxi/MAINTAINERS | 5 ++ + configs/orangepi_r1_defconfig | 26 ++++++++++ + 4 files changed, 109 insertions(+) create mode 100644 arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts + create mode 100644 configs/orangepi_r1_defconfig --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -22,15 +28,9 @@ Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> sun8i-h3-orangepi-2.dtb \ --- /dev/null +++ b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts -@@ -0,0 +1,157 @@ +@@ -0,0 +1,91 @@ +/* -+ * Copyright (C) 2017 Hauke Mehrtens <hauke@hauke-m.de> -+ * -+ * Based on sun8i-h2-plus-orangepi-zero.dts, which is: -+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz> -+ * -+ * Based on sun8i-h3-orangepi-one.dts, which is: -+ * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com> ++ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual @@ -71,112 +71,87 @@ Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> + * OTHER DEALINGS IN THE SOFTWARE. + */ + -+/dts-v1/; -+#include "sun8i-h3.dtsi" -+#include "sunxi-common-regulators.dtsi" -+ -+#include <dt-bindings/gpio/gpio.h> -+#include <dt-bindings/input/input.h> -+#include <dt-bindings/pinctrl/sun4i-a10.h> ++/* Orange Pi R1 is based on Orange Pi Zero design */ ++#include "sun8i-h2-plus-orangepi-zero.dts" + +/ { + model = "Xunlong Orange Pi R1"; + compatible = "xunlong,orangepi-r1", "allwinner,sun8i-h2-plus"; + -+ aliases { -+ serial0 = &uart0; -+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */ -+ ethernet1 = &xr819; -+ }; -+ -+ chosen { -+ stdout-path = "serial0:115200n8"; -+ }; -+ -+ leds { -+ compatible = "gpio-leds"; ++ /delete-node/ reg_vcc_wifi; + -+ pwr_led { -+ label = "orangepi:green:pwr"; -+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; -+ default-state = "on"; -+ }; -+ -+ status_led { -+ label = "orangepi:red:status"; -+ gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+ -+ reg_vcc_wifi: reg_vcc_wifi { ++ /* ++ * Ths pin of this regulator is the same with the Wi-Fi extra ++ * regulator on the original Zero. However it's used for USB ++ * Ethernet rather than the Wi-Fi now. ++ */ ++ reg_vcc_usb_eth: reg-vcc-usb-ethernet { + compatible = "regulator-fixed"; -+ regulator-min-microvolt = <3300000>; -+ regulator-max-microvolt = <3300000>; -+ regulator-name = "vcc-wifi"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ regulator-name = "vcc-usb-ethernet"; + enable-active-high; + gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>; + }; + -+ wifi_pwrseq: wifi_pwrseq { -+ compatible = "mmc-pwrseq-simple"; -+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; -+ }; -+}; -+ -+&ehci1 { -+ status = "okay"; -+}; -+ -+&emac { -+ phy = <&phy1>; -+ phy-mode = "mii"; -+ allwinner,use-internal-phy; -+ allwinner,leds-active-low; -+ status = "okay"; -+ phy1: ethernet-phy@1 { -+ reg = <1>; ++ aliases { ++ ethernet1 = &rtl8189etv; + }; +}; + -+&mmc0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&mmc0_pins_a>; -+ vmmc-supply = <®_vcc3v3>; -+ bus-width = <4>; -+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ -+ cd-inverted; -+ status = "okay"; ++&ohci1 { ++ /* ++ * RTL8152B USB-Ethernet adapter is connected to USB1, ++ * and it's a USB 2.0 device. So the OHCI1 controller ++ * can be left disabled. ++ */ ++ status = "disabled"; +}; + +&mmc1 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&mmc1_pins_a>; -+ vmmc-supply = <®_vcc_wifi>; -+ mmc-pwrseq = <&wifi_pwrseq>; -+ bus-width = <4>; -+ non-removable; -+ status = "okay"; ++ vmmc-supply = <®_vcc3v3>; ++ vqmmc-supply = <®_vcc3v3>; + -+ /* -+ * Explicitly define the sdio device, so that we can add an ethernet -+ * alias for it (which e.g. makes u-boot set a mac-address). -+ */ -+ xr819: sdio_wifi@1 { ++ rtl8189etv: sdio_wifi@1 { + reg = <1>; + }; +}; + -+&ohci1 { -+ status = "okay"; -+}; -+ -+&uart0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&uart0_pins_a>; -+ status = "okay"; -+}; -+ +&usbphy { -+ /* USB VBUS is always on */ -+ status = "okay"; ++ usb1_vbus-supply = <®_vcc_usb_eth>; +}; +--- a/board/sunxi/MAINTAINERS ++++ b/board/sunxi/MAINTAINERS +@@ -302,6 +302,11 @@ M: Jagan Teki <jagan@amarulasolutions.co + S: Maintained + F: configs/orangepi_prime_defconfig + ++ORANGEPI R1 BOARD ++M: Hauke Mehrtens <hauke@hauke-m.de> ++S: Maintained ++F: configs/orangepi_r1_defconfig ++ + PINE64 BOARDS + M: Andre Przywara <andre.przywara@arm.com> + S: Maintained +--- /dev/null ++++ b/configs/orangepi_r1_defconfig +@@ -0,0 +1,18 @@ ++CONFIG_ARM=y ++CONFIG_ARCH_SUNXI=y ++CONFIG_SPL_SPI_FLASH_SUPPORT=y ++CONFIG_MACH_SUN8I_H3=y ++CONFIG_DRAM_CLK=624 ++CONFIG_DRAM_ZQ=3881979 ++CONFIG_DRAM_ODT_EN=y ++# CONFIG_VIDEO_DE2 is not set ++CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-orangepi-r1" ++# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set ++CONFIG_CONSOLE_MUX=y ++CONFIG_SPL=y ++# CONFIG_CMD_IMLS is not set ++# CONFIG_CMD_FLASH is not set ++# CONFIG_CMD_FPGA is not set ++CONFIG_SPL_SPI_SUNXI=y ++CONFIG_SUN8I_EMAC=y ++CONFIG_USB_EHCI_HCD=y |