diff options
7 files changed, 606 insertions, 0 deletions
diff --git a/target/linux/mvebu/patches-3.19/019-mtd-nand-pxa3xx-Fix-PIO-FIFO-draining.patch b/target/linux/mvebu/patches-3.19/019-mtd-nand-pxa3xx-Fix-PIO-FIFO-draining.patch new file mode 100644 index 0000000000..bf2006927e --- /dev/null +++ b/target/linux/mvebu/patches-3.19/019-mtd-nand-pxa3xx-Fix-PIO-FIFO-draining.patch @@ -0,0 +1,97 @@ +From 11aa9df4de06cc257327d783c5cb615989e87286 Mon Sep 17 00:00:00 2001 +From: Maxime Ripard <maxime.ripard@free-electrons.com> +Date: Fri, 23 Jan 2015 15:18:27 +0100 +Subject: [PATCH v2 1/2] mtd: nand: pxa3xx: Fix PIO FIFO draining + +The NDDB register holds the data that are needed by the read and write +commands. + +However, during a read PIO access, the datasheet specifies that after each 32 +bits read in that register, when BCH is enabled, we have to make sure that the +RDDREQ bit is set in the NDSR register. + +This fixes an issue that was seen on the Armada 385, and presumably other mvebu +SoCs, when a read on a newly erased page would end up in the driver reporting a +timeout from the NAND. + +Cc: <stable@vger.kernel.org> # v3.14 +Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> +--- + drivers/mtd/nand/pxa3xx_nand.c | 45 ++++++++++++++++++++++++++++++++++++------ + 1 file changed, 39 insertions(+), 6 deletions(-) + +diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c +index 96b0b1d27df1..e6918befb951 100644 +--- a/drivers/mtd/nand/pxa3xx_nand.c ++++ b/drivers/mtd/nand/pxa3xx_nand.c +@@ -23,6 +23,7 @@ + #include <linux/mtd/partitions.h> + #include <linux/io.h> + #include <linux/irq.h> ++#include <linux/jiffies.h> + #include <linux/slab.h> + #include <linux/of.h> + #include <linux/of_device.h> +@@ -480,6 +481,38 @@ static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) + nand_writel(info, NDCR, ndcr | int_mask); + } + ++static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len) ++{ ++ u32 *dst = (u32 *)data; ++ ++ if (info->ecc_bch) { ++ while (len--) { ++ u32 timeout; ++ ++ *dst++ = nand_readl(info, NDDB); ++ ++ /* ++ * According to the datasheet, when reading ++ * from NDDB with BCH enabled, after each 32 ++ * bits reads, we have to make sure that the ++ * NDSR.RDDREQ bit is set ++ */ ++ timeout = jiffies + msecs_to_jiffies(5); ++ while (!(nand_readl(info, NDSR) & NDSR_RDDREQ)) { ++ if (!time_before(jiffies, timeout)) { ++ dev_err(&info->pdev->dev, ++ "Timeout on RDDREQ while draining the FIFO\n"); ++ return; ++ } ++ ++ cpu_relax(); ++ } ++ } ++ } else { ++ __raw_readsl(info->mmio_base + NDDB, data, len); ++ } ++} ++ + static void handle_data_pio(struct pxa3xx_nand_info *info) + { + unsigned int do_bytes = min(info->data_size, info->chunk_size); +@@ -496,14 +529,14 @@ static void handle_data_pio(struct pxa3xx_nand_info *info) + DIV_ROUND_UP(info->oob_size, 4)); + break; + case STATE_PIO_READING: +- __raw_readsl(info->mmio_base + NDDB, +- info->data_buff + info->data_buff_pos, +- DIV_ROUND_UP(do_bytes, 4)); ++ drain_fifo(info, ++ info->data_buff + info->data_buff_pos, ++ DIV_ROUND_UP(do_bytes, 4)); + + if (info->oob_size > 0) +- __raw_readsl(info->mmio_base + NDDB, +- info->oob_buff + info->oob_buff_pos, +- DIV_ROUND_UP(info->oob_size, 4)); ++ drain_fifo(info, ++ info->oob_buff + info->oob_buff_pos, ++ DIV_ROUND_UP(info->oob_size, 4)); + break; + default: + dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, +-- +2.2.2 + diff --git a/target/linux/mvebu/patches-3.19/020-ARM-mvebu-Add-a-number-of-pinctrl-functions.patch b/target/linux/mvebu/patches-3.19/020-ARM-mvebu-Add-a-number-of-pinctrl-functions.patch new file mode 100644 index 0000000000..7e27ae2b41 --- /dev/null +++ b/target/linux/mvebu/patches-3.19/020-ARM-mvebu-Add-a-number-of-pinctrl-functions.patch @@ -0,0 +1,70 @@ +From 91b4c91f919abffa72cbf7545a944252f8e4f775 Mon Sep 17 00:00:00 2001 +From: Maxime Ripard <maxime.ripard@free-electrons.com> +Date: Thu, 8 Jan 2015 18:38:08 +0100 +Subject: [PATCH 3/4] ARM: mvebu: Add a number of pinctrl functions + +Some pinctrl functions can be shared with all DTS out there, since they are +generic, SoC-wide muxing options. Add a number of these to the DTSI to avoid +duplication. + +Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> +Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> +Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> +Signed-off-by: Andrew Lunn <andrew@lunn.ch> +--- + arch/arm/boot/dts/armada-38x.dtsi | 39 +++++++++++++++++++++++++++++++++++++++ + 1 file changed, 39 insertions(+) + +diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi +index 40200084c6c8..98885c58be29 100644 +--- a/arch/arm/boot/dts/armada-38x.dtsi ++++ b/arch/arm/boot/dts/armada-38x.dtsi +@@ -195,6 +195,45 @@ + + pinctrl@18000 { + reg = <0x18000 0x20>; ++ ++ ge0_rgmii_pins: ge-rgmii-pins-0 { ++ marvell,pins = "mpp6", "mpp7", "mpp8", ++ "mpp9", "mpp10", "mpp11", ++ "mpp12", "mpp13", "mpp14", ++ "mpp15", "mpp16", "mpp17"; ++ marvell,function = "ge0"; ++ }; ++ ++ i2c0_pins: i2c-pins-0 { ++ marvell,pins = "mpp2", "mpp3"; ++ marvell,function = "i2c0"; ++ }; ++ ++ mdio_pins: mdio-pins { ++ marvell,pins = "mpp4", "mpp5"; ++ marvell,function = "ge"; ++ }; ++ ++ ref_clk0_pins: ref-clk-pins-0 { ++ marvell,pins = "mpp45"; ++ marvell,function = "ref"; ++ }; ++ ++ spi1_pins: spi-pins-1 { ++ marvell,pins = "mpp56", "mpp57", "mpp58", ++ "mpp59"; ++ marvell,function = "spi1"; ++ }; ++ ++ uart0_pins: uart-pins-0 { ++ marvell,pins = "mpp0", "mpp1"; ++ marvell,function = "ua0"; ++ }; ++ ++ uart1_pins: uart-pins-1 { ++ marvell,pins = "mpp19", "mpp20"; ++ marvell,function = "ua1"; ++ }; + }; + + gpio0: gpio@18100 { +-- +2.2.1 + diff --git a/target/linux/mvebu/patches-3.19/021-ARM-mvebu-Add-Armada-385-Access-Point-Development-Bo.patch b/target/linux/mvebu/patches-3.19/021-ARM-mvebu-Add-Armada-385-Access-Point-Development-Bo.patch new file mode 100644 index 0000000000..a40c957fb3 --- /dev/null +++ b/target/linux/mvebu/patches-3.19/021-ARM-mvebu-Add-Armada-385-Access-Point-Development-Bo.patch @@ -0,0 +1,220 @@ +From e5ee12817e9eac891c6b2a340f64d94d9abd355f Mon Sep 17 00:00:00 2001 +From: Maxime Ripard <maxime.ripard@free-electrons.com> +Date: Thu, 8 Jan 2015 18:38:09 +0100 +Subject: [PATCH 4/4] ARM: mvebu: Add Armada 385 Access Point Development Board + support + +The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB +SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage. + +[gregory.clement@free-electrons.com: switch the license to the dual +X11/GPL with the agreement of the author] + +Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> +Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> +Signed-off-by: Andrew Lunn <andrew@lunn.ch> +--- + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/armada-385-db-ap.dts | 178 +++++++++++++++++++++++++++++++++ + 2 files changed, 179 insertions(+) + create mode 100644 arch/arm/boot/dts/armada-385-db-ap.dts + +diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile +index 6dc9c17f9ff5..d34837104949 100644 +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -536,6 +536,7 @@ dtb-$(CONFIG_MACH_ARMADA_375) += \ + armada-375-db.dtb + dtb-$(CONFIG_MACH_ARMADA_38X) += \ + armada-385-db.dtb \ ++ armada-385-db-ap.dtb \ + armada-385-rd.dtb + dtb-$(CONFIG_MACH_ARMADA_XP) += \ + armada-xp-axpwifiap.dtb \ +diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts +new file mode 100644 +index 000000000000..57b9119fb3e0 +--- /dev/null ++++ b/arch/arm/boot/dts/armada-385-db-ap.dts +@@ -0,0 +1,178 @@ ++/* ++ * Device Tree file for Marvell Armada 385 Access Point Development board ++ * (DB-88F6820-AP) ++ * ++ * Copyright (C) 2014 Marvell ++ * ++ * Nadav Haklai <nadavh@marvell.com> ++ * ++ * This file is dual-licensed: you can use it either under the terms ++ * of the GPL or the X11 license, at your option. Note that this dual ++ * licensing only applies to this file, and not this project as a ++ * whole. ++ * ++ * a) This file is licensed under the terms of the GNU General Public ++ * License version 2. This program is licensed "as is" without ++ * any warranty of any kind, whether express or implied. ++ * ++ * Or, alternatively, ++ * ++ * b) Permission is hereby granted, free of charge, to any person ++ * obtaining a copy of this software and associated documentation ++ * files (the "Software"), to deal in the Software without ++ * restriction, including without limitation the rights to use, ++ * copy, modify, merge, publish, distribute, sublicense, and/or ++ * sell copies of the Software, and to permit persons to whom the ++ * Software is furnished to do so, subject to the following ++ * conditions: ++ * ++ * The above copyright notice and this permission notice shall be ++ * included in all copies or substantial portions of the Software. ++ * ++ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, ++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES ++ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND ++ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT ++ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, ++ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING ++ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR ++ * OTHER DEALINGS IN THE SOFTWARE. ++ */ ++ ++/dts-v1/; ++#include "armada-385.dtsi" ++ ++#include <dt-bindings/gpio/gpio.h> ++ ++/ { ++ model = "Marvell Armada 385 Access Point Development Board"; ++ compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada38x"; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200"; ++ stdout-path = &uart1; ++ }; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x80000000>; /* 2GB */ ++ }; ++ ++ soc { ++ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 ++ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; ++ ++ internal-regs { ++ spi1: spi@10680 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins>; ++ status = "okay"; ++ ++ spi-flash@0 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "st,m25p128"; ++ reg = <0>; /* Chip select 0 */ ++ spi-max-frequency = <54000000>; ++ }; ++ }; ++ ++ i2c0: i2c@11000 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ status = "okay"; ++ ++ /* ++ * This bus is wired to two EEPROM ++ * sockets, one of which holding the ++ * board ID used by the bootloader. ++ * Erasing this EEPROM's content will ++ * brick the board. ++ * Use this bus with caution. ++ */ ++ }; ++ ++ mdio@72004 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mdio_pins>; ++ ++ phy0: ethernet-phy@1 { ++ reg = <1>; ++ }; ++ ++ phy1: ethernet-phy@4 { ++ reg = <4>; ++ }; ++ ++ phy2: ethernet-phy@6 { ++ reg = <6>; ++ }; ++ }; ++ ++ /* UART0 is exposed through the JP8 connector */ ++ uart0: serial@12000 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins>; ++ status = "okay"; ++ }; ++ ++ /* ++ * UART1 is exposed through a FTDI chip ++ * wired to the mini-USB connector ++ */ ++ uart1: serial@12100 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++ }; ++ ++ ethernet@30000 { ++ status = "okay"; ++ phy = <&phy2>; ++ phy-mode = "sgmii"; ++ }; ++ ++ ethernet@34000 { ++ status = "okay"; ++ phy = <&phy1>; ++ phy-mode = "sgmii"; ++ }; ++ ++ ethernet@70000 { ++ pinctrl-names = "default"; ++ ++ /* ++ * The Reference Clock 0 is used to ++ * provide a clock to the PHY ++ */ ++ pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>; ++ status = "okay"; ++ phy = <&phy0>; ++ phy-mode = "rgmii-id"; ++ }; ++ }; ++ ++ pcie-controller { ++ status = "okay"; ++ ++ /* ++ * The three PCIe units are accessible through ++ * standard mini-PCIe slots on the board. ++ */ ++ pcie@1,0 { ++ /* Port 0, Lane 0 */ ++ status = "okay"; ++ }; ++ ++ pcie@2,0 { ++ /* Port 1, Lane 0 */ ++ status = "okay"; ++ }; ++ ++ pcie@3,0 { ++ /* Port 2, Lane 0 */ ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +-- +2.2.1 + diff --git a/target/linux/mvebu/patches-3.19/022-ARM-mvebu-A385-AP-Enable-the-NAND-controller.patch b/target/linux/mvebu/patches-3.19/022-ARM-mvebu-A385-AP-Enable-the-NAND-controller.patch new file mode 100644 index 0000000000..85a9511547 --- /dev/null +++ b/target/linux/mvebu/patches-3.19/022-ARM-mvebu-A385-AP-Enable-the-NAND-controller.patch @@ -0,0 +1,39 @@ +From 7eb1f09ec8e25aa2fc3f6fc5fc9405d9f917d503 Mon Sep 17 00:00:00 2001 +From: Maxime Ripard <maxime.ripard@free-electrons.com> +Date: Thu, 11 Dec 2014 14:14:58 +0100 +Subject: [PATCH 1/2] ARM: mvebu: A385-AP: Enable the NAND controller + +The A385 AP has a 1GB NAND chip. Enable it. + +Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> +--- + arch/arm/boot/dts/armada-385-db-ap.dts | 13 +++++++++++++ + 1 file changed, 13 insertions(+) + +diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts +index 3a51531eb37b..02db04867d8f 100644 +--- a/arch/arm/boot/dts/armada-385-db-ap.dts ++++ b/arch/arm/boot/dts/armada-385-db-ap.dts +@@ -122,6 +122,19 @@ + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; ++ ++ nfc: flash@d0000 { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ num-cs = <1>; ++ nand-ecc-strength = <4>; ++ nand-ecc-step-size = <512>; ++ marvell,nand-keep-config; ++ marvell,nand-enable-arbiter; ++ nand-on-flash-bbt; ++ }; + }; + + pcie-controller { +-- +2.2.1 + diff --git a/target/linux/mvebu/patches-3.19/023-pinctrl-mvebu-a38x-Add-UART1-muxing-options.patch b/target/linux/mvebu/patches-3.19/023-pinctrl-mvebu-a38x-Add-UART1-muxing-options.patch new file mode 100644 index 0000000000..cd85d9d155 --- /dev/null +++ b/target/linux/mvebu/patches-3.19/023-pinctrl-mvebu-a38x-Add-UART1-muxing-options.patch @@ -0,0 +1,43 @@ +From a95308d88c07e0093aedae7e64f92cb1e165f592 Mon Sep 17 00:00:00 2001 +From: Maxime Ripard <maxime.ripard@free-electrons.com> +Date: Fri, 5 Dec 2014 15:44:57 +0100 +Subject: [PATCH] pinctrl: mvebu: a38x: Add UART1 muxing options + +The MPP19 and MMP20 pins also have the ability to be muxed to the uart1 +function. + +Add this case to the pinctrl driver. + +Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> +Acked-by: Jason Cooper <jason@lakedaemon.net> +Signed-off-by: Linus Walleij <linus.walleij@linaro.org> +--- + drivers/pinctrl/mvebu/pinctrl-armada-38x.c | 6 ++++-- + 1 file changed, 4 insertions(+), 2 deletions(-) + +diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-38x.c b/drivers/pinctrl/mvebu/pinctrl-armada-38x.c +index 224c6cff6aa2..7302f66f4f19 100644 +--- a/drivers/pinctrl/mvebu/pinctrl-armada-38x.c ++++ b/drivers/pinctrl/mvebu/pinctrl-armada-38x.c +@@ -145,14 +145,16 @@ static struct mvebu_mpp_mode armada_38x_mpp_modes[] = { + MPP_VAR_FUNCTION(2, "ptp", "event_req", V_88F6810_PLUS), + MPP_VAR_FUNCTION(3, "pcie0", "clkreq", V_88F6810_PLUS), + MPP_VAR_FUNCTION(4, "sata1", "prsnt", V_88F6810_PLUS), +- MPP_VAR_FUNCTION(5, "ua0", "cts", V_88F6810_PLUS)), ++ MPP_VAR_FUNCTION(5, "ua0", "cts", V_88F6810_PLUS), ++ MPP_VAR_FUNCTION(6, "ua1", "rxd", V_88F6810_PLUS)), + MPP_MODE(20, + MPP_VAR_FUNCTION(0, "gpio", NULL, V_88F6810_PLUS), + MPP_VAR_FUNCTION(1, "ge0", "txclk", V_88F6810_PLUS), + MPP_VAR_FUNCTION(2, "ptp", "clk", V_88F6810_PLUS), + MPP_VAR_FUNCTION(3, "pcie1", "rstout", V_88F6820_PLUS), + MPP_VAR_FUNCTION(4, "sata0", "prsnt", V_88F6810_PLUS), +- MPP_VAR_FUNCTION(5, "ua0", "rts", V_88F6810_PLUS)), ++ MPP_VAR_FUNCTION(5, "ua0", "rts", V_88F6810_PLUS), ++ MPP_VAR_FUNCTION(6, "ua1", "txd", V_88F6810_PLUS)), + MPP_MODE(21, + MPP_VAR_FUNCTION(0, "gpio", NULL, V_88F6810_PLUS), + MPP_VAR_FUNCTION(1, "spi0", "cs1", V_88F6810_PLUS), +-- +2.2.1 + diff --git a/target/linux/mvebu/patches-3.19/024-ARM-mvebu-a38x-Fix-node-names.patch b/target/linux/mvebu/patches-3.19/024-ARM-mvebu-a38x-Fix-node-names.patch new file mode 100644 index 0000000000..7b506e75a8 --- /dev/null +++ b/target/linux/mvebu/patches-3.19/024-ARM-mvebu-a38x-Fix-node-names.patch @@ -0,0 +1,98 @@ +From 4a25432b13090b57d257fa0ffb6712d8acf94523 Mon Sep 17 00:00:00 2001 +From: Maxime Ripard <maxime.ripard@free-electrons.com> +Date: Thu, 8 Jan 2015 18:38:05 +0100 +Subject: [PATCH 1/4] ARM: mvebu: a38x: Fix node names + +Some nodes in the DTs have a reg property but no unit name in their node name. + +This contradicts the way the ePAPR defines the node names. Fix this. + +Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> +Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> +Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> +Signed-off-by: Andrew Lunn <andrew@lunn.ch> +--- + arch/arm/boot/dts/armada-380.dtsi | 2 +- + arch/arm/boot/dts/armada-385-db.dts | 2 +- + arch/arm/boot/dts/armada-385-rd.dts | 2 +- + arch/arm/boot/dts/armada-385.dtsi | 2 +- + arch/arm/boot/dts/armada-38x.dtsi | 4 ++-- + 5 files changed, 6 insertions(+), 6 deletions(-) + +diff --git a/arch/arm/boot/dts/armada-380.dtsi b/arch/arm/boot/dts/armada-380.dtsi +index 4173a8ab34e7..13400ce88c54 100644 +--- a/arch/arm/boot/dts/armada-380.dtsi ++++ b/arch/arm/boot/dts/armada-380.dtsi +@@ -32,7 +32,7 @@ + + soc { + internal-regs { +- pinctrl { ++ pinctrl@18000 { + compatible = "marvell,mv88f6810-pinctrl"; + reg = <0x18000 0x20>; + }; +diff --git a/arch/arm/boot/dts/armada-385-db.dts b/arch/arm/boot/dts/armada-385-db.dts +index 2aaa9d2ac284..212605ccc7b6 100644 +--- a/arch/arm/boot/dts/armada-385-db.dts ++++ b/arch/arm/boot/dts/armada-385-db.dts +@@ -74,7 +74,7 @@ + phy-mode = "rgmii-id"; + }; + +- mdio { ++ mdio@72004 { + phy0: ethernet-phy@0 { + reg = <0>; + }; +diff --git a/arch/arm/boot/dts/armada-385-rd.dts b/arch/arm/boot/dts/armada-385-rd.dts +index aaca2861dc87..74a3bfe6efd7 100644 +--- a/arch/arm/boot/dts/armada-385-rd.dts ++++ b/arch/arm/boot/dts/armada-385-rd.dts +@@ -67,7 +67,7 @@ + }; + + +- mdio { ++ mdio@72004 { + phy0: ethernet-phy@0 { + reg = <0>; + }; +diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/armada-385.dtsi +index 6283d7912f71..5249a4d3c207 100644 +--- a/arch/arm/boot/dts/armada-385.dtsi ++++ b/arch/arm/boot/dts/armada-385.dtsi +@@ -37,7 +37,7 @@ + + soc { + internal-regs { +- pinctrl { ++ pinctrl@18000 { + compatible = "marvell,mv88f6820-pinctrl"; + reg = <0x18000 0x20>; + }; +diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi +index 74391dace9e7..ada1f206028b 100644 +--- a/arch/arm/boot/dts/armada-38x.dtsi ++++ b/arch/arm/boot/dts/armada-38x.dtsi +@@ -193,7 +193,7 @@ + status = "disabled"; + }; + +- pinctrl { ++ pinctrl@18000 { + compatible = "marvell,mv88f6820-pinctrl"; + reg = <0x18000 0x20>; + }; +@@ -373,7 +373,7 @@ + status = "disabled"; + }; + +- mdio { ++ mdio@72004 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; +-- +2.2.1 + diff --git a/target/linux/mvebu/patches-3.19/208-ARM-mvebu-385-ap-Add-partitions.patch b/target/linux/mvebu/patches-3.19/208-ARM-mvebu-385-ap-Add-partitions.patch new file mode 100644 index 0000000000..0c59d47956 --- /dev/null +++ b/target/linux/mvebu/patches-3.19/208-ARM-mvebu-385-ap-Add-partitions.patch @@ -0,0 +1,39 @@ +From 9861f93a59142a3131870df2521eb2deb73026d7 Mon Sep 17 00:00:00 2001 +From: Maxime Ripard <maxime.ripard@free-electrons.com> +Date: Tue, 13 Jan 2015 11:14:09 +0100 +Subject: [PATCH 2/2] ARM: mvebu: 385-ap: Add partitions + +Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> +--- + arch/arm/boot/dts/armada-385-db-ap.dts | 15 +++++++++++++++ + 1 file changed, 15 insertions(+) + +diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts +index 02db04867d8f..2a58443e2504 100644 +--- a/arch/arm/boot/dts/armada-385-db-ap.dts ++++ b/arch/arm/boot/dts/armada-385-db-ap.dts +@@ -134,6 +134,21 @@ + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; ++ ++ mtd0@00000000 { ++ label = "u-boot"; ++ reg = <0x00000000 0x00800000>; ++ }; ++ ++ mtd1@00800000 { ++ label = "kernel"; ++ reg = <0x00800000 0x00800000>; ++ }; ++ ++ mtd2@01000000 { ++ label = "ubi"; ++ reg = <0x01000000 0x3f000000>; ++ }; + }; + }; + +-- +2.2.1 + |