diff options
5 files changed, 295 insertions, 1 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 786c6f70e1..3417466fbb 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -21,6 +21,11 @@ tplink,vr2600v) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0" ;; +qcom,ipq8064-ap161) + ucidef_set_interface_lan "eth1 eth2" + ucidef_add_switch "switch0" \ + "0:lan" "1:lan" "2:lan" "3u@eth1" "6:wan" "4u@eth0" + ;; linksys,ea8500) hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 6e282f99f4..4b88f9cf5e 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -16,6 +16,7 @@ platform_do_upgrade() { netgear,r7500v2 |\ netgear,r7800 |\ qcom,ipq8064-ap148 |\ + qcom,ipq8064-ap161 |\ zyxel,nbg6817) nand_do_upgrade "$ARGV" ;; diff --git a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-ap161.dts b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-ap161.dts new file mode 100644 index 0000000000..8c5a4fe53d --- /dev/null +++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-ap161.dts @@ -0,0 +1,274 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +/ { + model = "Qualcomm IPQ8064/AP161"; + compatible = "qcom,ipq8064-ap161", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &gsbi4_serial; + mdio-gpio0 = &mdio0; + }; + + chosen { + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + drive-strength = <10>; + bias-none; + }; + }; + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + pullups { + pins = "gpio39"; + bias-pull-up; + }; + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio2", "gpio27", "gpio28", + "gpio29", "gpio30", "gpio31", + "gpio32", "gpio51", "gpio52", + "gpio59", "gpio60", "gpio61", + "gpio62" , "gpio66"; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + gsbi5: gsbi@1a200000 { + qcom,mode = <GSBI_PROT_SPI>; + status = "ok"; + + spi4: spi@1a280000 { + status = "ok"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 0>; + + flash: m25p80@0 { + compatible = "s25fl256s1"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "qcom,smem"; + }; + }; + }; + }; + + sata-phy@1b400000 { + status = "ok"; + }; + + sata@29000000 { + status = "ok"; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + }; + + pcie1: pci@1b700000 { + status = "ok"; + force_gen1 = <1>; + }; + + pcie2: pci@1b900000 { + status = "ok"; + }; + + nand@1ac00000 { + status = "ok"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + cs0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "qcom,smem"; + }; + }; + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x20080 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy3: ethernet-phy@3 { + device_type = "ethernet-phy"; + reg = <3>; + }; + }; + + gmac0: ethernet@37000000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <0>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index b82d54b0f6..5902eee6ac 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -201,6 +201,19 @@ define Device/qcom_ipq8064-ap148-legacy endef TARGET_DEVICES += qcom_ipq8064-ap148-legacy +define Device/qcom_ipq8064-ap161 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_DTS := qcom-ipq8064-ap161 + KERNEL_INSTALL := 1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + BOARD_NAME := ap161 + DEVICE_TITLE := Qualcomm AP161 + DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct +endef +TARGET_DEVICES += qcom_ipq8064-ap161 + define Device/qcom_ipq8064-db149 $(call Device/FitImage) DEVICE_DTS := qcom-ipq8064-db149 diff --git a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch index b94e4828c9..0a62a0bc84 100644 --- a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch @@ -10,13 +10,14 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -699,6 +699,16 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -699,6 +699,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8084-mtp.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ qcom-ipq8064-ap148.dtb \ + qcom-ipq8064-c2600.dtb \ + qcom-ipq8064-d7800.dtb \ + qcom-ipq8064-db149.dtb \ ++ qcom-ipq8064-ap161.dtb \ + qcom-ipq8064-ea8500.dtb \ + qcom-ipq8064-r7500.dtb \ + qcom-ipq8064-r7500v2.dtb \ |