diff options
8 files changed, 400 insertions, 8 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index a7ace1f92e..53c2a80993 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -33,6 +33,11 @@ ea8500) ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio" ucidef_set_led_default "wps" "WPS" "ea8500:green:wps" "0" ;; +nbg6817) + ucidef_set_led_wlan "wlan2g" "WLAN2g" "$board:amber:wifi" "phy1radio" + ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5" "phy0radio" + ucidef_set_led_netdev "wan" "WAN" "$board:white:internet" "eth1" + ;; *) ;; esac diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index b72045538a..a461033dfe 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -35,6 +35,13 @@ ea8500) ucidef_set_interface_macaddr "lan" "$hw_mac_addr" ucidef_set_interface_macaddr "wan" "$hw_mac_addr" ;; +nbg6817) + hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) + ucidef_add_switch "switch0" \ + "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0" + ucidef_set_interface_macaddr "lan" "$hw_mac_addr" + ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 1)" + ;; *) echo "Unsupported hardware. Network interfaces not intialized" ;; diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index c7977e6375..f95692a889 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -56,6 +56,9 @@ case "$FIRMWARE" in hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) ath10kcal_extract "art" 4096 12064 ;; + nbg6817) + ath10kcal_extract "0:ART" 4096 12064 + ;; r7500v2 |\ r7800) ath10kcal_extract "art" 4096 12064 @@ -72,6 +75,9 @@ case "$FIRMWARE" in hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) ath10kcal_extract "art" 20480 12064 ;; + nbg6817) + ath10kcal_extract "0:ART" 20480 12064 + ;; r7500v2 |\ r7800) ath10kcal_extract "art" 20480 12064 diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh index ea45381d91..1bd0e2bd94 100644 --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh @@ -26,6 +26,9 @@ ipq806x_board_detect() { *"DB149") name="db149" ;; + *"NBG6817") + name="nbg6817" + ;; *"R7500") name="r7500" ;; diff --git a/target/linux/ipq806x/config-4.4 b/target/linux/ipq806x/config-4.4 index bc040497cb..1972e3675e 100644 --- a/target/linux/ipq806x/config-4.4 +++ b/target/linux/ipq806x/config-4.4 @@ -61,6 +61,7 @@ CONFIG_ARM_THUMB=y CONFIG_ARM_UNWIND=y CONFIG_ARM_VIRT_EXT=y CONFIG_AT803X_PHY=y +CONFIG_BLK_DEV_LOOP=y # CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_BOUNCE=y @@ -197,11 +198,6 @@ CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_HAVE_HW_BREAKPOINT=y CONFIG_HAVE_IDE=y CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y -CONFIG_HAVE_KERNEL_GZIP=y -CONFIG_HAVE_KERNEL_LZ4=y -CONFIG_HAVE_KERNEL_LZMA=y -CONFIG_HAVE_KERNEL_LZO=y -CONFIG_HAVE_KERNEL_XZ=y CONFIG_HAVE_MEMBLOCK=y CONFIG_HAVE_MOD_ARCH_SPECIFIC=y CONFIG_HAVE_NET_DSA=y @@ -262,6 +258,16 @@ CONFIG_MFD_SYSCON=y CONFIG_MIGHT_HAVE_CACHE_L2X0=y CONFIG_MIGHT_HAVE_PCI=y CONFIG_MIGRATION=y +CONFIG_MMC=y +CONFIG_MMC_ARMMMCI=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_MINORS=16 +CONFIG_MMC_QCOM_DML=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_MSM=y +# CONFIG_MMC_SDHCI_PCI is not set +CONFIG_MMC_SDHCI_PLTFM=y +# CONFIG_MMC_TIFM_SD is not set CONFIG_MODULES_TREE_LOOKUP=y CONFIG_MODULES_USE_ELF_REL=y CONFIG_MSM_GCC_8660=y @@ -378,7 +384,6 @@ CONFIG_QCOM_SCM=y CONFIG_QCOM_SCM_32=y # CONFIG_QCOM_SMD is not set CONFIG_QCOM_SMEM=y -# CONFIG_QCOM_SPMI_TEMP_ALARM is not set CONFIG_QCOM_WDT=y CONFIG_RAS=y CONFIG_RATIONAL=y @@ -389,6 +394,7 @@ CONFIG_RD_GZIP=y CONFIG_REGMAP=y CONFIG_REGMAP_MMIO=y CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y CONFIG_REGULATOR_QCOM_RPM=y # CONFIG_REGULATOR_QCOM_SPMI is not set CONFIG_RESET_CONTROLLER=y diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts new file mode 100644 index 0000000000..cc56213fdb --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts @@ -0,0 +1,341 @@ +#include "qcom-ipq8065-v1.0.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "ZyXEL NBG6817"; + compatible = "zyxel,nbg6817", "qcom,ipq8065"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + sdcc1 = &sdcc1; + }; + + chosen { + bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd"; + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + pinctrl-0 = <&mdio0_pins &rgmii2_pins>; + pinctrl-names = "default"; + + i2c4_pins: i2c4_pinmux { + mux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + + clk { + pins = "gpio1"; + input-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + + tx { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; + input-disable; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + drive-strength = <10>; + bias-none; + }; + + cs { + pins = "gpio20"; + drive-strength = <12>; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + gsbi5: gsbi@1a200000 { + qcom,mode = <GSBI_PROT_SPI>; + status = "ok"; + + spi4: spi@1a280000 { + status = "ok"; + spi-max-frequency = <50000000>; + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash: m25p80@0 { + compatible = "s25fl512s"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <51200000>; + reg = <0>; + + linux,part-probe = "qcom-smem"; + }; + }; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + }; + + pcie1: pci@1b700000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ + 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ + 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ + 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ + 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ + 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ + 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ + 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ + 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ + 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ + 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ + 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ + 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ + 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + qca,ar8327-initvals = < + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x0000c 0x80 /* PAD6_MODE */ + >; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <0>; + qcom,rgmii_delay = <1>; + qcom,phy_mii_type = <0>; + qcom,emulation = <0>; + qcom,irq = <255>; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + qcom,phy_mdio_addr = <0>; /* none */ + qcom,poll_required = <0>; /* no polling */ + qcom,rgmii_delay = <0>; + qcom,phy_mii_type = <1>; + qcom,emulation = <0>; + qcom,irq = <258>; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + rpm@108000 { + pinctrl-0 = <&i2c4_pins>; + pinctrl-names = "default"; + }; + + amba { + sdcc1: sdcc@12400000 { + status = "okay"; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; + }; + + + + }; + + gpio-keys { + compatible = "gpio-keys"; + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RFKILL>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + internet { + label = "nbg6817:white:internet"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + + power { + label = "nbg6817:white:power"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + wifi { + label = "nbg6817:amber:wifi"; + gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>; + }; + + wifi5g { + label = "nbg6817:amber:wifi5g"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + usb0_status { + gpio-export,name = "usb0"; + gpio-export,output = <1>; + gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>; + }; + + usb1_status { + gpio-export,name = "usb1"; + gpio-export,output = <1>; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; + }; + usb1_power { + gpio-export,name = "usb1_power"; + gpio-export,output = <1>; + gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>; + }; + usb2_power { + gpio-export,name = "usb2_power"; + gpio-export,output = <1>; + gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index b74f1a77c2..3bee923f93 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -90,6 +90,19 @@ define Device/TpSafeImage endef DEVICE_VARS += TPLINK_BOARD_NAME +define Device/ZyXELImage + PROFILES += $$(DEVICE_NAME) + FILESYSTEMS := squashfs + KERNEL_SUFFIX := -uImage + KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$$${KERNEL_SIZE} + KERNEL_NAME := zImage + IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin + IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ + IMAGE/sysupgrade.tar := sysupgrade-tar + IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE} + IMAGE/mmcblk0p4-kernel.bin := append-kernel +endef + define Device/AP148 $(call Device/FitImage) $(call Device/UbiFit) @@ -202,6 +215,16 @@ define Device/R7800 DEVICE_PACKAGES := ath10k-firmware-qca9984 endef -TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 +define Device/NBG6817 + DEVICE_DTS := qcom-ipq8065-nbg6817 + KERNEL_SIZE := 4096k + BLOCKSIZE := 64k + BOARD_NAME := nbg6817 + DEVICE_TITLE := ZyXEL NBG6817 + DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs losetup + $(call Device/ZyXELImage) +endef + +TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817 $(eval $(call BuildImage)) diff --git a/target/linux/ipq806x/patches-4.4/800-devicetree.patch b/target/linux/ipq806x/patches-4.4/800-devicetree.patch index 85f253429b..916e2efd72 100644 --- a/target/linux/ipq806x/patches-4.4/800-devicetree.patch +++ b/target/linux/ipq806x/patches-4.4/800-devicetree.patch @@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -506,7 +506,13 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -506,7 +506,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ qcom-ipq8064-ap148.dtb \ @@ -22,6 +22,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org> + qcom-ipq8064-ea8500.dtb \ + qcom-ipq8064-r7500.dtb \ + qcom-ipq8064-r7500v2.dtb \ ++ qcom-ipq8065-nbg6817.dtb \ + qcom-ipq8065-r7800.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ |