diff options
| -rw-r--r-- | target/linux/ixp4xx-2.6/patches/400-pronghorn_metro.patch | 353 |
1 files changed, 353 insertions, 0 deletions
diff --git a/target/linux/ixp4xx-2.6/patches/400-pronghorn_metro.patch b/target/linux/ixp4xx-2.6/patches/400-pronghorn_metro.patch new file mode 100644 index 0000000000..f4773cf31f --- /dev/null +++ b/target/linux/ixp4xx-2.6/patches/400-pronghorn_metro.patch @@ -0,0 +1,353 @@ +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig 2007-04-02 16:10:51.000000000 +0200 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig 2007-04-02 16:11:12.000000000 +0200 +@@ -49,6 +49,22 @@ + WG302 v2 or WAG302 v2 Access Points. For more information + on this platform, see http://openwrt.org + ++config MACH_PRONGHORN ++ bool "Pronghorn" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the ADI ++ Engineering Pronghorn Platform. For more ++ information on this platform, see <file:Documentation/arm/IXP4xx>. ++ ++config MACH_PRONGHORNMETRO ++ bool "Pronghorn Metro" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the ADI ++ Engineering Pronghorn Metro Platform. For more ++ information on this platform, see <file:Documentation/arm/IXP4xx>. ++ + config ARCH_IXDP425 + bool "IXDP425" + help +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile 2007-04-02 16:10:51.000000000 +0200 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile 2007-04-02 16:15:51.000000000 +0200 +@@ -13,6 +13,7 @@ + obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o + obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o + obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o ++obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o + + obj-y += common.o + +@@ -24,5 +25,6 @@ + obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o nas100d-power.o + obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o + obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o ++obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/pronghornmetro-pci.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/pronghornmetro-pci.c +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/pronghornmetro-pci.c 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/pronghornmetro-pci.c 2007-04-02 16:17:35.000000000 +0200 +@@ -0,0 +1,70 @@ ++/* ++ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c ++ * ++ * PCI setup routines for ADI Engineering Pronghorn Metro platform ++ * ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ * Author: Copied from coyote-pci.c ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <asm/hardware.h> ++#include <asm/irq.h> ++ ++#include <asm/mach/pci.h> ++ ++extern void ixp4xx_pci_preinit(void); ++extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); ++extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys); ++ ++void __init pronghornmetro_pci_preinit(void) ++{ ++ set_irq_type(IRQ_PCI_SLOT0, IRQT_LOW); ++ set_irq_type(IRQ_PCI_SLOT1, IRQT_LOW); ++ set_irq_type(IRQ_PCI_SLOT2, IRQT_LOW); ++ set_irq_type(IRQ_PCI_SLOT3, IRQT_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init pronghornmetro_map_irq(struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == PCI_SLOT0_DEVID) ++ return IRQ_PCI_SLOT0; ++ else if (slot == PCI_SLOT1_DEVID) ++ return IRQ_PCI_SLOT1; ++ else if (slot == PCI_SLOT2_DEVID) ++ return IRQ_PCI_SLOT2; ++ else if (slot == PCI_SLOT3_DEVID) ++ return IRQ_PCI_SLOT3; ++ else return -1; ++} ++ ++struct hw_pci pronghornmetro_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = pronghornmetro_pci_preinit, ++ .swizzle = pci_std_swizzle, ++ .setup = ixp4xx_setup, ++ .scan = ixp4xx_scan_bus, ++ .map_irq = pronghornmetro_map_irq, ++}; ++ ++int __init pronghornmetro_pci_init(void) ++{ ++ if (machine_is_pronghorn_metro()) ++ pci_common_init(&pronghornmetro_pci); ++ return 0; ++} ++ ++subsys_initcall(pronghornmetro_pci_init); +diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/pronghornmetro-setup.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/pronghornmetro-setup.c +--- linux-2.6.19.2/arch/arm/mach-ixp4xx/pronghornmetro-setup.c 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/pronghornmetro-setup.c 2007-04-02 16:18:13.000000000 +0200 +@@ -0,0 +1,119 @@ ++/* ++ * arch/arm/mach-ixp4xx/pronghornmetro-setup.c ++ * ++ * Board setup for ADI Engineering Pronghorn Metro ++ * ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Copied from coyote-setup.c ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++ ++#include <asm/types.h> ++#include <asm/setup.h> ++#include <asm/memory.h> ++#include <asm/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data pronghornmetro_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource pronghornmetro_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device pronghornmetro_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &pronghornmetro_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &pronghornmetro_flash_resource, ++}; ++ ++static struct resource pronghornmetro_uart_resource = { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct ixp4xx_i2c_pins pronghornmetro_i2c_gpio_pins = { ++ .sda_pin = PRONGHORNMETRO_SDA_PIN, ++ .scl_pin = PRONGHORNMETRO_SCL_PIN, ++}; ++ ++static struct platform_device pronghornmetro_i2c_controller = { ++ .name = "IXP4XX-I2C", ++ .id = 0, ++ .dev = { ++ .platform_data = &pronghornmetro_i2c_gpio_pins, ++ }, ++ .num_resources = 0 ++}; ++ ++static struct plat_serial8250_port pronghornmetro_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device pronghornmetro_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = pronghornmetro_uart_data, ++ }, ++ .num_resources = 1, ++ .resource = &pronghornmetro_uart_resource, ++}; ++ ++static struct platform_device *pronghornmetro_devices[] __initdata = { ++ &pronghornmetro_i2c_controller, ++ &pronghornmetro_flash, ++ &pronghornmetro_uart ++}; ++ ++static void __init pronghornmetro_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ pronghornmetro_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ pronghornmetro_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(pronghornmetro_devices, ARRAY_SIZE(pronghornmetro_devices)); ++} ++ ++#ifdef CONFIG_MACH_PRONGHORNMETRO ++MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro") ++ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, ++ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .timer = &ixp4xx_timer, ++ .boot_params = 0x0100, ++ .init_machine = pronghornmetro_init, ++MACHINE_END ++#endif +diff -Nur linux-2.6.19.2/Documentation/arm/IXP4xx linux-2.6.19.2-owrt/Documentation/arm/IXP4xx +--- linux-2.6.19.2/Documentation/arm/IXP4xx 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2-owrt/Documentation/arm/IXP4xx 2007-04-02 16:11:12.000000000 +0200 +@@ -111,6 +111,9 @@ + the platform has two mini-PCI slots used for 802.11[bga] cards. + Finally, there is an IDE port hanging off the expansion bus. + ++ADI Engineering Pronghorn Metro Platform ++http://www.adiengineering.com/productsPronghornMetro.html ++ + Gateworks Avila Network Platform + http://www.gateworks.com/avila_sbc.htm + +diff -Nur linux-2.6.19.2/include/asm-arm/arch-ixp4xx/hardware.h linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/hardware.h +--- linux-2.6.19.2/include/asm-arm/arch-ixp4xx/hardware.h 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/hardware.h 2007-04-02 16:11:12.000000000 +0200 +@@ -43,6 +43,7 @@ + /* Platform specific details */ + #include "ixdp425.h" + #include "coyote.h" ++#include "pronghornmetro.h" + #include "prpmc1100.h" + #include "nslu2.h" + #include "nas100d.h" +diff -Nur linux-2.6.19.2/include/asm-arm/arch-ixp4xx/irqs.h linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/irqs.h +--- linux-2.6.19.2/include/asm-arm/arch-ixp4xx/irqs.h 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/irqs.h 2007-04-02 16:11:12.000000000 +0200 +@@ -94,6 +94,21 @@ + #define IRQ_COYOTE_IDE IRQ_IXP4XX_GPIO5 + + /* ++ * ADI Pronghorn Metro Board IRQs ++ */ ++#if defined(CONFIG_MACH_PRONGHORNMETRO) ++#define IRQ_PCI_SLOT0 IRQ_IXP4XX_GPIO4 ++#define IRQ_PCI_SLOT1 IRQ_IXP4XX_GPIO6 ++#define IRQ_PCI_SLOT2 IRQ_IXP4XX_GPIO11 ++#define IRQ_PCI_SLOT3 IRQ_IXP4XX_GPIO1 ++#define IRQ_IDE IRQ_IXP4XX_GPIO0 ++#elif defined (CONFIG_MACH_PRONGHORN) ++#define IRQ_PCI_SLOT0 IRQ_IXP4XX_GPIO11 ++#define IRQ_PCI_SLOT1 IRQ_IXP4XX_GPIO6 ++#define IRQ_IDE IRQ_IXP4XX_GPIO0 ++#endif ++ ++/* + * NSLU2 board IRQs + */ + #define IRQ_NSLU2_PCI_INTA IRQ_IXP4XX_GPIO11 +diff -Nur linux-2.6.19.2/include/asm-arm/arch-ixp4xx/pronghornmetro.h linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/pronghornmetro.h +--- linux-2.6.19.2/include/asm-arm/arch-ixp4xx/pronghornmetro.h 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/pronghornmetro.h 2007-04-02 16:11:12.000000000 +0200 +@@ -0,0 +1,47 @@ ++/* ++ * include/asm-arm/arch-ixp4xx/pronghornmetro.h ++ * ++ * ADI Engineering platform specific definitions ++ * ++ * Copyright 2004 (c) MontaVista, Software, Inc. ++ * ++ * This file is licensed under the terms of the GNU General Public ++ * License version 2. This program is licensed "as is" without any ++ * warranty of any kind, whether express or implied. ++ */ ++ ++#ifndef __ASM_ARCH_HARDWARE_H__ ++#error "Do not include this directly, instead #include <asm/hardware.h>" ++#endif ++ ++#if defined(CONFIG_MACH_PRONGHORNMETRO) ++#define PRONGHORNMETRO_SDA_PIN 9 ++#define PRONGHORNMETRO_SCL_PIN 10 ++ ++/* PCI controller GPIO to IRQ pin mappings */ ++#define PCI_SLOT0_PIN 1 ++#define PCI_SLOT1_PIN 11 ++#define PCI_SLOT2_PIN 6 ++#define PCI_SLOT3_PIN 4 ++ ++#define PCI_SLOT0_DEVID 13 ++#define PCI_SLOT1_DEVID 14 ++#define PCI_SLOT2_DEVID 15 ++#define PCI_SLOT3_DEVID 16 ++ ++#define TASKFILE_CS 3 ++#define TASKFILE_CS_REG IXP4XX_EXP_CS3 ++#define ALTSTAT_CS 4 ++ ++#elif defined(CONFIG_MACH_PRONGHORN) ++/* PCI controller GPIO to IRQ pin mappings */ ++#define PCI_SLOT0_PIN 11 ++#define PCI_SLOT1_PIN 6 ++ ++#define PCI_SLOT0_DEVID 15 ++#define PCI_SLOT1_DEVID 14 ++ ++#define TASKFILE_CS 2 ++#define TASKFILE_CS_REG IXP4XX_EXP_CS2 ++#define ALTSTAT_CS 3 ++#endif +diff -Nur linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h +--- linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h 2007-04-02 16:10:51.000000000 +0200 ++++ linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h 2007-04-02 16:12:24.000000000 +0200 +@@ -40,7 +40,7 @@ + /* + * Some boards are using UART2 as console + */ +- if (machine_is_adi_coyote() || machine_is_gtwx5715() || machine_is_gateway7001() || machine_is_wg302v2()) ++ if (machine_is_adi_coyote() || machine_is_gtwx5715() || machine_is_gateway7001() || machine_is_wg302v2() || machine_is_pronghorn() || machine_is_pronghorn_metro()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; |