aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--target/linux/apm821xx/Makefile2
-rw-r--r--target/linux/apm821xx/config-4.9327
-rw-r--r--target/linux/apm821xx/patches-4.9/200-add-meraki-mr24-ikarem-support.patch32
-rw-r--r--target/linux/apm821xx/patches-4.9/201-add-amcc-apollo3g-support.patch30
-rw-r--r--target/linux/apm821xx/patches-4.9/202-add-netgear-wndr4700-support.patch32
-rw-r--r--target/linux/apm821xx/patches-4.9/203-add-meraki-mx60-buckminster-support.patch32
-rw-r--r--target/linux/apm821xx/patches-4.9/300-fix-atheros-nics-on-apm82181.patch51
-rw-r--r--target/linux/apm821xx/patches-4.9/301-fix-memory-map-wndr4700.patch14
-rw-r--r--target/linux/apm821xx/patches-4.9/701-powerpc_ibm_apm82181_phyclk_fix.patch52
-rw-r--r--target/linux/apm821xx/patches-4.9/702-powerpc_ibm_phy_add_dt_parser.patch328
-rw-r--r--target/linux/apm821xx/patches-4.9/801-usb-xhci-add-firmware-loader-for-uPD720201-and-uPD72.patch545
-rw-r--r--target/linux/apm821xx/patches-4.9/802-usb-xhci-force-msi-renesas-xhci.patch54
-rw-r--r--target/linux/apm821xx/patches-4.9/804-usb-dwc2-add-amcc-usb-otg-405ex.patch48
-rw-r--r--target/linux/apm821xx/patches-4.9/901-hwmon-add-driver-for-Microchip-TC654-TC655-PWM-fan-c.patch1027
14 files changed, 2573 insertions, 1 deletions
diff --git a/target/linux/apm821xx/Makefile b/target/linux/apm821xx/Makefile
index 026466d86d..6d711543c4 100644
--- a/target/linux/apm821xx/Makefile
+++ b/target/linux/apm821xx/Makefile
@@ -13,7 +13,7 @@ MAINTAINER:=Chris Blake <chrisrblake93@gmail.com>, \
Christian Lamparter <chunkeey@gmail.com>
SUBTARGETS:=nand sata
-KERNEL_PATCHVER:=4.4
+KERNEL_PATCHVER:=4.9
define Target/Description
Build images for AppliedMicro APM821xx based boards.
diff --git a/target/linux/apm821xx/config-4.9 b/target/linux/apm821xx/config-4.9
new file mode 100644
index 0000000000..d9b3283f29
--- /dev/null
+++ b/target/linux/apm821xx/config-4.9
@@ -0,0 +1,327 @@
+# CONFIG_40x is not set
+CONFIG_44x=y
+CONFIG_460EX=y
+CONFIG_4xx=y
+CONFIG_4xx_SOC=y
+# CONFIG_ADVANCED_OPTIONS is not set
+CONFIG_APM821xx=y
+CONFIG_APOLLO3G=y
+# CONFIG_ARCHES is not set
+CONFIG_ARCH_DMA_ADDR_T_64BIT=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+CONFIG_ARCH_HAS_DMA_SET_COHERENT_MASK=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAS_WALK_MEMORY=y
+CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
+CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
+# CONFIG_ARCH_RANDOM is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
+CONFIG_ARCH_SUPPORTS_DEFERRED_STRUCT_PAGE_INIT=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_AUDIT_ARCH=y
+# CONFIG_BAMBOO is not set
+CONFIG_BCH=y
+CONFIG_BLK_MQ_PCI=y
+# CONFIG_BLUESTONE is not set
+CONFIG_BOOKE=y
+CONFIG_BOOKE_WDT=y
+# CONFIG_BOUNCE is not set
+CONFIG_BUCKMINSTER=y
+# CONFIG_CANYONLANDS is not set
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_CMDLINE="rootfstype=squashfs noinitrd"
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CRC16=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_DEV_PPC4XX=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_MD5_PPC=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_SHA1_PPC=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_DECOMPRESS_GZIP=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_DTC=y
+# CONFIG_E200 is not set
+CONFIG_EARLY_PRINTK=y
+# CONFIG_EBONY is not set
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+# CONFIG_EIGER is not set
+# CONFIG_EPAPR_BOOT is not set
+CONFIG_EXTRA_TARGETS="uImage"
+CONFIG_FIXED_PHY=y
+CONFIG_FREEZER=y
+# CONFIG_FSL_LBC is not set
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+# CONFIG_GENERIC_CSUM is not set
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_GENERIC_MSI_IRQ=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_GENERIC_TIME_VSYSCALL_OLD=y
+# CONFIG_GEN_RTC is not set
+# CONFIG_GE_FPGA is not set
+# CONFIG_GLACIER is not set
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_GENERIC=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAS_RAPIDIO is not set
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+# CONFIG_HAVE_ARCH_BITREVERSE is not set
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CBPF_JIT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_HAVE_GENERIC_RCU_GUP=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IOREMAP_PROT=y
+CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_PPC4XX=y
+CONFIG_HZ=1000
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ_PERIODIC=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_IBM_IIC=y
+CONFIG_IBM_EMAC=y
+CONFIG_IBM_EMAC_EMAC4=y
+CONFIG_IBM_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_EMAC_RGMII=y
+CONFIG_IBM_EMAC_RXB=128
+CONFIG_IBM_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_EMAC_RX_SKB_HEADROOM=0
+CONFIG_IBM_EMAC_TAH=y
+CONFIG_IBM_EMAC_TXB=128
+# CONFIG_ICON is not set
+CONFIG_IKAREM=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_IOMMU_HELPER is not set
+# CONFIG_IPIC is not set
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_ISA_DMA_API=y
+# CONFIG_JFFS2_FS is not set
+# CONFIG_KATMAI is not set
+CONFIG_KERNEL_GZIP=y
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_LEDS_TRIGGER_MTD=y
+CONFIG_LIBFDT=y
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+# CONFIG_MATH_EMULATION is not set
+CONFIG_MDIO_BOARDINFO=y
+# CONFIG_MDIO_HISI_FEMAC is not set
+# CONFIG_MFD_ACT8945A is not set
+# CONFIG_MFD_MAX77620 is not set
+# CONFIG_MMIO_NVRAM is not set
+CONFIG_MODULES_USE_ELF_RELA=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_U3_HT_IRQS is not set
+# CONFIG_MPIC_WEIRD is not set
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+# CONFIG_MTD_CFI_GEOMETRY is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_BCH=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_ECC_BCH=y
+CONFIG_MTD_NAND_ECC_SMC=y
+CONFIG_MTD_NAND_NDFC=y
+# CONFIG_MTD_SPLIT is not set
+# CONFIG_MTD_SPLIT_SQUASHFS_ROOT is not set
+CONFIG_NEED_DMA_MAP_STATE=y
+# CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK is not set
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NEED_SG_DMA_LENGTH=y
+# CONFIG_NONSTATIC_KERNEL is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_NO_BOOTMEM=y
+CONFIG_NR_IRQS=512
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_ADDRESS_PCI=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OF_PCI=y
+CONFIG_OF_PCI_IRQ=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND=y
+CONFIG_PAGE_OFFSET=0xc0000000
+CONFIG_PCI=y
+CONFIG_PCIEAER=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCIE_PME=y
+CONFIG_PCI_BUS_ADDR_T_64BIT=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_MSI=y
+# CONFIG_PCI_MSI_IRQ_DOMAIN is not set
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PHYSICAL_START=0x00000000
+CONFIG_PHYS_64BIT=y
+CONFIG_PHYS_ADDR_T_64BIT=y
+CONFIG_PM=y
+CONFIG_PM_AUTOSLEEP=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_PM_WAKELOCKS=y
+CONFIG_PM_WAKELOCKS_GC=y
+CONFIG_PM_WAKELOCKS_LIMIT=100
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_PPC44x_SIMPLE=y
+CONFIG_PPC4xx_CPM=y
+CONFIG_PPC4xx_GPIO=y
+# CONFIG_PPC4xx_HSTA_MSI is not set
+CONFIG_PPC4xx_MSI=y
+CONFIG_PPC4xx_OCM=y
+CONFIG_PPC4xx_PCI_EXPRESS=y
+# CONFIG_PPC64 is not set
+# CONFIG_PPC_47x is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_PPC_970_NAP is not set
+CONFIG_PPC_ADV_DEBUG_DACS=2
+CONFIG_PPC_ADV_DEBUG_DAC_RANGE=y
+CONFIG_PPC_ADV_DEBUG_DVCS=2
+CONFIG_PPC_ADV_DEBUG_IACS=4
+CONFIG_PPC_ADV_DEBUG_REGS=y
+# CONFIG_PPC_BOOK3S_32 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PPC_COPRO_BASE is not set
+CONFIG_PPC_DCR=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DOORBELL is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+# CONFIG_PPC_EPAPR_HV_PIC is not set
+CONFIG_PPC_FPU=y
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_ICP_HV is not set
+# CONFIG_PPC_ICP_NATIVE is not set
+# CONFIG_PPC_ICS_RTAS is not set
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PPC_LIB_RHEAP=y
+CONFIG_PPC_MMU_NOHASH=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_PPC_MPC106 is not set
+CONFIG_PPC_MSI_BITMAP=y
+# CONFIG_PPC_P7_NAP is not set
+CONFIG_PPC_PCI_CHOICE=y
+# CONFIG_PPC_RTAS is not set
+CONFIG_PPC_UDBG_16550=y
+CONFIG_PPC_WERROR=y
+# CONFIG_PPC_XICS is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_PTE_64BIT=y
+# CONFIG_QORIQ_THERMAL is not set
+# CONFIG_RAINIER is not set
+CONFIG_RAS=y
+# CONFIG_RCU_STALL_COMMON is not set
+CONFIG_RD_GZIP=y
+# CONFIG_RELOCATABLE is not set
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+# CONFIG_SAM440EP is not set
+CONFIG_SCHED_HRTICK=y
+# CONFIG_SCHED_INFO is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SEQUOIA is not set
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_FSL=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_SG_POOL is not set
+CONFIG_SIMPLE_GPIO=y
+CONFIG_SPARSE_IRQ=y
+CONFIG_SRCU=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_SWIOTLB is not set
+CONFIG_SWPHY=y
+CONFIG_SYSCTL_EXCEPTION_TRACE=y
+# CONFIG_TAISHAN is not set
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_USB_SUPPORT=y
+CONFIG_VDSO32=y
+# CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set
+# CONFIG_WARP is not set
+CONFIG_WATCHDOG_CORE=y
+CONFIG_WNDR4700=y
+# CONFIG_XILINX_SYSACE is not set
+# CONFIG_XILINX_VIRTEX440_GENERIC_BOARD is not set
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_XZ_DEC_POWERPC=y
+# CONFIG_YOSEMITE is not set
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
diff --git a/target/linux/apm821xx/patches-4.9/200-add-meraki-mr24-ikarem-support.patch b/target/linux/apm821xx/patches-4.9/200-add-meraki-mr24-ikarem-support.patch
new file mode 100644
index 0000000000..018bcf21a0
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/200-add-meraki-mr24-ikarem-support.patch
@@ -0,0 +1,32 @@
+--- a/arch/powerpc/platforms/44x/Kconfig
++++ b/arch/powerpc/platforms/44x/Kconfig
+@@ -40,6 +40,19 @@ config EBONY
+ help
+ This option enables support for the IBM PPC440GP evaluation board.
+
++config IKAREM
++ bool "Ikarem"
++ depends on 44x
++ default n
++ select PPC44x_SIMPLE
++ select APM821xx
++ select PCI_MSI
++ select PPC4xx_MSI
++ select PPC4xx_PCI_EXPRESS
++ select IBM_EMAC_RGMII
++ help
++ This option enables support for the Cisco Meraki MR24 (Ikarem) Access Point.
++
+ config SAM440EP
+ bool "Sam440ep"
+ depends on 44x
+--- a/arch/powerpc/platforms/44x/ppc44x_simple.c
++++ b/arch/powerpc/platforms/44x/ppc44x_simple.c
+@@ -62,6 +62,7 @@ static char *board[] __initdata = {
+ "amcc,sequoia",
+ "amcc,taishan",
+ "amcc,yosemite",
++ "meraki,ikarem",
+ "mosaixtech,icon"
+ };
+
diff --git a/target/linux/apm821xx/patches-4.9/201-add-amcc-apollo3g-support.patch b/target/linux/apm821xx/patches-4.9/201-add-amcc-apollo3g-support.patch
new file mode 100644
index 0000000000..0581a43e33
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/201-add-amcc-apollo3g-support.patch
@@ -0,0 +1,30 @@
+--- a/arch/powerpc/platforms/44x/Kconfig
++++ b/arch/powerpc/platforms/44x/Kconfig
+@@ -143,6 +143,17 @@ config CANYONLANDS
+ help
+ This option enables support for the AMCC PPC460EX evaluation board.
+
++config APOLLO3G
++ bool "Apollo3G"
++ depends on 44x
++ default n
++ select PPC44x_SIMPLE
++ select APM821xx
++ select IBM_EMAC_RGMII
++ select 460EX
++ help
++ This option enables support for the AMCC Apollo 3G board.
++
+ config GLACIER
+ bool "Glacier"
+ depends on 44x
+--- a/arch/powerpc/platforms/44x/ppc44x_simple.c
++++ b/arch/powerpc/platforms/44x/ppc44x_simple.c
+@@ -50,6 +50,7 @@ machine_device_initcall(ppc44x_simple, p
+ * board.c file for it rather than adding it to this list.
+ */
+ static char *board[] __initdata = {
++ "amcc,apollo3g",
+ "amcc,arches",
+ "amcc,bamboo",
+ "apm,bluestone",
diff --git a/target/linux/apm821xx/patches-4.9/202-add-netgear-wndr4700-support.patch b/target/linux/apm821xx/patches-4.9/202-add-netgear-wndr4700-support.patch
new file mode 100644
index 0000000000..6b6db1dddb
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/202-add-netgear-wndr4700-support.patch
@@ -0,0 +1,32 @@
+--- a/arch/powerpc/platforms/44x/Makefile
++++ b/arch/powerpc/platforms/44x/Makefile
+@@ -3,6 +3,7 @@ ifneq ($(CONFIG_PPC4xx_CPM),y)
+ obj-$(CONFIG_44x) += idle.o
+ endif
+ obj-$(CONFIG_PPC44x_SIMPLE) += ppc44x_simple.o
++obj-$(CONFIG_WNDR4700) += wndr4700.o
+ obj-$(CONFIG_EBONY) += ebony.o
+ obj-$(CONFIG_SAM440EP) += sam440ep.o
+ obj-$(CONFIG_WARP) += warp.o
+--- a/arch/powerpc/platforms/44x/Kconfig
++++ b/arch/powerpc/platforms/44x/Kconfig
+@@ -260,6 +260,19 @@ config ICON
+ help
+ This option enables support for the AMCC PPC440SPe evaluation board.
+
++config WNDR4700
++ bool "WNDR4700"
++ depends on 44x
++ default n
++ select APM821xx
++ select PCI_MSI
++ select PPC4xx_MSI
++ select PPC4xx_PCI_EXPRESS
++ select IBM_EMAC_RGMII
++ select 460EX
++ help
++ This option enables support for the Netgear WNDR4700/WNDR4720 board.
++
+ config XILINX_VIRTEX440_GENERIC_BOARD
+ bool "Generic Xilinx Virtex 5 FXT board support"
+ depends on 44x
diff --git a/target/linux/apm821xx/patches-4.9/203-add-meraki-mx60-buckminster-support.patch b/target/linux/apm821xx/patches-4.9/203-add-meraki-mx60-buckminster-support.patch
new file mode 100644
index 0000000000..8c072387d4
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/203-add-meraki-mx60-buckminster-support.patch
@@ -0,0 +1,32 @@
+--- a/arch/powerpc/platforms/44x/Kconfig
++++ b/arch/powerpc/platforms/44x/Kconfig
+@@ -30,6 +30,19 @@ config BLUESTONE
+ help
+ This option enables support for the APM APM821xx Evaluation board.
+
++config BUCKMINSTER
++ bool "Buckminster"
++ depends on 44x
++ default n
++ select APM821xx
++ select PCI_MSI
++ select PPC4xx_MSI
++ select PPC4xx_PCI_EXPRESS
++ select IBM_EMAC_RGMII
++ select 460EX
++ help
++ This option enables support for the Cisco Meraki MX60/MX60W (Buckminster) Security Appliance
++
+ config EBONY
+ bool "Ebony"
+ depends on 44x
+--- a/arch/powerpc/platforms/44x/ppc44x_simple.c
++++ b/arch/powerpc/platforms/44x/ppc44x_simple.c
+@@ -63,6 +63,7 @@ static char *board[] __initdata = {
+ "amcc,sequoia",
+ "amcc,taishan",
+ "amcc,yosemite",
++ "meraki,buckminster",
+ "meraki,ikarem",
+ "mosaixtech,icon"
+ };
diff --git a/target/linux/apm821xx/patches-4.9/300-fix-atheros-nics-on-apm82181.patch b/target/linux/apm821xx/patches-4.9/300-fix-atheros-nics-on-apm82181.patch
new file mode 100644
index 0000000000..0b1affcfe7
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/300-fix-atheros-nics-on-apm82181.patch
@@ -0,0 +1,51 @@
+--- a/arch/powerpc/sysdev/ppc4xx_pci.c
++++ b/arch/powerpc/sysdev/ppc4xx_pci.c
+@@ -1066,15 +1066,24 @@ static int __init apm821xx_pciex_init_po
+ u32 val;
+
+ /*
+- * Do a software reset on PCIe ports.
+- * This code is to fix the issue that pci drivers doesn't re-assign
+- * bus number for PCIE devices after Uboot
+- * scanned and configured all the buses (eg. PCIE NIC IntelPro/1000
+- * PT quad port, SAS LSI 1064E)
++ * Only reset the PHY when no link is currently established.
++ * This is for the Atheros PCIe board which has problems to establish
++ * the link (again) after this PHY reset. All other currently tested
++ * PCIe boards don't show this problem.
+ */
+-
+- mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST, 0x0);
+- mdelay(10);
++ val = mfdcri(SDR0, port->sdr_base + PESDRn_LOOP);
++ if (!(val & 0x00001000)) {
++ /*
++ * Do a software reset on PCIe ports.
++ * This code is to fix the issue that pci drivers doesn't re-assign
++ * bus number for PCIE devices after Uboot
++ * scanned and configured all the buses (eg. PCIE NIC IntelPro/1000
++ * PT quad port, SAS LSI 1064E)
++ */
++
++ mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST, 0x0);
++ mdelay(10);
++ }
+
+ if (port->endpoint)
+ val = PTYPE_LEGACY_ENDPOINT << 20;
+@@ -1091,9 +1100,12 @@ static int __init apm821xx_pciex_init_po
+ mtdcri(SDR0, PESDR0_460EX_L0DRV, 0x00000130);
+ mtdcri(SDR0, PESDR0_460EX_L0CLK, 0x00000006);
+
+- mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST, 0x10000000);
+- mdelay(50);
+- mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST, 0x30000000);
++ val = mfdcri(SDR0, port->sdr_base + PESDRn_LOOP);
++ if (!(val & 0x00001000)) {
++ mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST, 0x10000000);
++ mdelay(50);
++ mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST, 0x30000000);
++ }
+
+ mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET,
+ mfdcri(SDR0, port->sdr_base + PESDRn_RCSSET) |
diff --git a/target/linux/apm821xx/patches-4.9/301-fix-memory-map-wndr4700.patch b/target/linux/apm821xx/patches-4.9/301-fix-memory-map-wndr4700.patch
new file mode 100644
index 0000000000..d6a1006177
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/301-fix-memory-map-wndr4700.patch
@@ -0,0 +1,14 @@
+--- a/arch/powerpc/sysdev/ppc4xx_pci.c
++++ b/arch/powerpc/sysdev/ppc4xx_pci.c
+@@ -1913,9 +1913,9 @@ static void __init ppc4xx_configure_pcie
+ * if it works
+ */
+ out_le32(mbase + PECFG_PIM0LAL, 0x00000000);
+- out_le32(mbase + PECFG_PIM0LAH, 0x00000000);
++ out_le32(mbase + PECFG_PIM0LAH, 0x00000008);
+ out_le32(mbase + PECFG_PIM1LAL, 0x00000000);
+- out_le32(mbase + PECFG_PIM1LAH, 0x00000000);
++ out_le32(mbase + PECFG_PIM1LAH, 0x0000000c);
+ out_le32(mbase + PECFG_PIM01SAH, 0xffff0000);
+ out_le32(mbase + PECFG_PIM01SAL, 0x00000000);
+
diff --git a/target/linux/apm821xx/patches-4.9/701-powerpc_ibm_apm82181_phyclk_fix.patch b/target/linux/apm821xx/patches-4.9/701-powerpc_ibm_apm82181_phyclk_fix.patch
new file mode 100644
index 0000000000..93a0858b26
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/701-powerpc_ibm_apm82181_phyclk_fix.patch
@@ -0,0 +1,52 @@
+--- a/drivers/net/ethernet/ibm/emac/core.c
++++ b/drivers/net/ethernet/ibm/emac/core.c
+@@ -129,6 +129,7 @@ static inline void emac_report_timeout_e
+ {
+ if (emac_has_feature(dev, EMAC_FTR_440GX_PHY_CLK_FIX |
+ EMAC_FTR_460EX_PHY_CLK_FIX |
++ EMAC_FTR_APM821XX_PHY_CLK_FIX |
+ EMAC_FTR_440EP_PHY_CLK_FIX))
+ DBG(dev, "%s" NL, error);
+ else if (net_ratelimit())
+@@ -146,6 +147,10 @@ static inline void emac_rx_clk_tx(struct
+ if (emac_has_feature(dev, EMAC_FTR_440EP_PHY_CLK_FIX))
+ dcri_clrset(SDR0, SDR0_MFR,
+ 0, SDR0_MFR_ECS >> dev->cell_index);
++
++ if (emac_has_feature(dev, EMAC_FTR_APM821XX_PHY_CLK_FIX))
++ dcri_clrset(SDR0, SDR0_ETH_CFG,
++ 0, 0x00000100 >> dev->cell_index);
+ #endif
+ }
+
+@@ -155,6 +160,10 @@ static inline void emac_rx_clk_default(s
+ if (emac_has_feature(dev, EMAC_FTR_440EP_PHY_CLK_FIX))
+ dcri_clrset(SDR0, SDR0_MFR,
+ SDR0_MFR_ECS >> dev->cell_index, 0);
++
++ if (emac_has_feature(dev, EMAC_FTR_APM821XX_PHY_CLK_FIX))
++ dcri_clrset(SDR0, SDR0_ETH_CFG,
++ 0x00000100 >> dev->cell_index, 0);
+ #endif
+ }
+
+@@ -2617,7 +2626,7 @@ static int emac_init_config(struct emac_
+ if (of_device_is_compatible(np, "ibm,emac-apm821xx")) {
+ dev->features |= (EMAC_APM821XX_REQ_JUMBO_FRAME_SIZE |
+ EMAC_FTR_APM821XX_NO_HALF_DUPLEX |
+- EMAC_FTR_460EX_PHY_CLK_FIX);
++ EMAC_FTR_APM821XX_PHY_CLK_FIX);
+ }
+ } else if (of_device_is_compatible(np, "ibm,emac4")) {
+ dev->features |= EMAC_FTR_EMAC4;
+--- a/drivers/net/ethernet/ibm/emac/core.h
++++ b/drivers/net/ethernet/ibm/emac/core.h
+@@ -333,6 +333,8 @@ struct emac_instance {
+ */
+ #define EMAC_FTR_APM821XX_NO_HALF_DUPLEX 0x00001000
+
++#define EMAC_FTR_APM821XX_PHY_CLK_FIX 0x000002000
++
+ /* Right now, we don't quite handle the always/possible masks on the
+ * most optimal way as we don't have a way to say something like
+ * always EMAC4. Patches welcome.
diff --git a/target/linux/apm821xx/patches-4.9/702-powerpc_ibm_phy_add_dt_parser.patch b/target/linux/apm821xx/patches-4.9/702-powerpc_ibm_phy_add_dt_parser.patch
new file mode 100644
index 0000000000..f1edb9cc7a
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/702-powerpc_ibm_phy_add_dt_parser.patch
@@ -0,0 +1,328 @@
+From b1c54da602ae9215cfbde1c3ed3b6296b76f07fc Mon Sep 17 00:00:00 2001
+Message-Id: <b1c54da602ae9215cfbde1c3ed3b6296b76f07fc.1486337989.git.chunkeey@googlemail.com>
+In-Reply-To: <246bd6614529d28dc48b11981ab5dae7a7364fc2.1486337989.git.chunkeey@googlemail.com>
+References: <246bd6614529d28dc48b11981ab5dae7a7364fc2.1486337989.git.chunkeey@googlemail.com>
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Mon, 13 Jun 2016 15:42:21 +0200
+Subject: [RFC 2/2] net: emac: add support for device-tree based PHY discovery
+ and setup
+To: netdev@vger.kernel.org,
+ devicetree@vger.kernel.org
+Cc: David S. Miller <davem@davemloft.net>,
+ Ivan Mikhaylov <ivan@de.ibm.com>,
+ Mark Rutland <mark.rutland@arm.com>,
+ Rob Herring <robh+dt@kernel.org>
+
+This patch adds glue-code that allows the EMAC driver to interface
+with the existing dt-supported PHYs in drivers/net/phy.
+
+Because currently, the emac driver maintains a small library of
+supported phys for in a private phy.c file located in the drivers
+directory.
+
+The support is limited to mostly single ethernet transceiver like the:
+CIS8201, BCM5248, ET1011C, Marvell 88E1111 and 88E1112, AR8035.
+However, routers like the Netgear WNDR4700 and Cisco Meraki MX60(W)
+have a 5-port switch (QCA8327N) attached to the MDIO of the EMAC.
+The switch chip has already a proper phy-driver (ar8216) that uses
+the generic phy library.
+
+Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
+---
+--- a/drivers/net/ethernet/ibm/emac/core.c
++++ b/drivers/net/ethernet/ibm/emac/core.c
+@@ -42,6 +42,7 @@
+ #include <linux/of_address.h>
+ #include <linux/of_irq.h>
+ #include <linux/of_net.h>
++#include <linux/of_mdio.h>
+ #include <linux/slab.h>
+
+ #include <asm/processor.h>
+@@ -2422,6 +2423,229 @@ static int emac_read_uint_prop(struct de
+ return 0;
+ }
+
++static void emac_adjust_link(struct net_device *ndev)
++{
++ struct emac_instance *dev = netdev_priv(ndev);
++ struct phy_device *phy = dev->phy_dev;
++
++ dev->phy.autoneg = phy->autoneg;
++ dev->phy.speed = phy->speed;
++ dev->phy.duplex = phy->duplex;
++ dev->phy.pause = phy->pause;
++ dev->phy.asym_pause = phy->asym_pause;
++ dev->phy.advertising = phy->advertising;
++}
++
++static int emac_mii_bus_read(struct mii_bus *bus, int addr, int regnum)
++{
++ return emac_mdio_read(bus->priv, addr, regnum);
++}
++
++static int emac_mii_bus_write(struct mii_bus *bus, int addr, int regnum, u16 val)
++{
++ emac_mdio_write(bus->priv, addr, regnum, val);
++ return 0;
++}
++
++static int emac_mii_bus_reset(struct mii_bus *bus)
++{
++ struct emac_instance *dev = netdev_priv(bus->priv);
++ int err;
++
++ err = emac_reset(dev);
++ if (err)
++ return err;
++ /* Meraki MX60(W)'s uboot will disable the switch and
++ * a bus reset won't do anything. */
++ emac_mii_reset_phy(&dev->phy);
++ return 0;
++}
++
++static int emac_mdio_setup_aneg(struct mii_phy *phy, u32 advertise)
++{
++ struct net_device *ndev = phy->dev;
++ struct emac_instance *dev = netdev_priv(ndev);
++
++ dev->phy.autoneg = AUTONEG_ENABLE;
++ dev->phy.speed = SPEED_1000;
++ dev->phy.duplex = DUPLEX_FULL;
++ dev->phy.advertising = advertise;
++ phy->autoneg = AUTONEG_ENABLE;
++ phy->speed = dev->phy.speed;
++ phy->duplex = dev->phy.duplex;
++ phy->advertising = advertise;
++ return phy_start_aneg(dev->phy_dev);
++}
++
++static int emac_mdio_setup_forced(struct mii_phy *phy, int speed, int fd)
++{
++ struct net_device *ndev = phy->dev;
++ struct emac_instance *dev = netdev_priv(ndev);
++
++ dev->phy.autoneg = AUTONEG_DISABLE;
++ dev->phy.speed = speed;
++ dev->phy.duplex = fd;
++ phy->autoneg = AUTONEG_DISABLE;
++ phy->speed = speed;
++ phy->duplex = fd;
++ return phy_start_aneg(dev->phy_dev);
++}
++
++static int emac_mdio_poll_link(struct mii_phy *phy)
++{
++ struct net_device *ndev = phy->dev;
++ struct emac_instance *dev = netdev_priv(ndev);
++ int res;
++
++ res = phy_read_status(dev->phy_dev);
++ if (res) {
++ dev_err(&dev->ofdev->dev, "link update failed (%d).", res);
++ return ethtool_op_get_link(ndev);
++ }
++
++ return dev->phy_dev->link;
++}
++
++static int emac_mdio_read_link(struct mii_phy *phy)
++{
++ struct net_device *ndev = phy->dev;
++ struct emac_instance *dev = netdev_priv(ndev);
++ int res;
++
++ res = phy_read_status(dev->phy_dev);
++ if (res)
++ return res;
++
++ dev->phy.speed = phy->speed;
++ dev->phy.duplex = phy->duplex;
++ dev->phy.pause = phy->pause;
++ dev->phy.asym_pause = phy->asym_pause;
++ return 0;
++}
++
++static int emac_mdio_init_phy(struct mii_phy *phy)
++{
++ struct net_device *ndev = phy->dev;
++ struct emac_instance *dev = netdev_priv(ndev);
++
++ phy_start(dev->phy_dev);
++ dev->phy.autoneg = phy->autoneg;
++ dev->phy.speed = phy->speed;
++ dev->phy.duplex = phy->duplex;
++ dev->phy.advertising = phy->advertising;
++ dev->phy.pause = phy->pause;
++ dev->phy.asym_pause = phy->asym_pause;
++
++ return phy_init_hw(dev->phy_dev);
++}
++
++static const struct mii_phy_ops emac_dt_mdio_phy_ops = {
++ .init = emac_mdio_init_phy,
++ .setup_aneg = emac_mdio_setup_aneg,
++ .setup_forced = emac_mdio_setup_forced,
++ .poll_link = emac_mdio_poll_link,
++ .read_link = emac_mdio_read_link,
++};
++
++static int emac_dt_mdio_probe(struct emac_instance *dev)
++{
++ struct device_node *mii_np;
++ int res;
++
++ mii_np = of_get_child_by_name(dev->ofdev->dev.of_node, "mdio");
++ if (!mii_np) {
++ dev_err(&dev->ofdev->dev, "no mdio definition found.");
++ return -ENODEV;
++ }
++
++ if (!of_device_is_available(mii_np)) {
++ res = 1;
++ goto put_node;
++ }
++
++ dev->mii_bus = devm_mdiobus_alloc(&dev->ofdev->dev);
++ if (!dev->mii_bus) {
++ res = -ENOMEM;
++ goto put_node;
++ }
++
++ dev->mii_bus->priv = dev->ndev;
++ dev->mii_bus->parent = dev->ndev->dev.parent;
++ dev->mii_bus->name = "emac_mdio";
++ dev->mii_bus->read = &emac_mii_bus_read;
++ dev->mii_bus->write = &emac_mii_bus_write;
++ dev->mii_bus->reset = &emac_mii_bus_reset;
++ snprintf(dev->mii_bus->id, MII_BUS_ID_SIZE, "%s", dev->ofdev->name);
++ res = of_mdiobus_register(dev->mii_bus, mii_np);
++ if (res) {
++ dev_err(&dev->ofdev->dev, "cannot register MDIO bus %s (%d)",
++ dev->mii_bus->name, res);
++ }
++
++ put_node:
++ of_node_put(mii_np);
++ return res;
++}
++
++static int emac_dt_phy_probe(struct emac_instance *dev,
++ struct device_node *phy_handle)
++{
++ u32 phy_flags = 0;
++ int res;
++
++ res = of_property_read_u32(phy_handle, "phy-flags", &phy_flags);
++ if (res < 0 && res != -EINVAL)
++ return res;
++
++ dev->phy.def = devm_kzalloc(&dev->ofdev->dev, sizeof(*dev->phy.def),
++ GFP_KERNEL);
++ if (!dev->phy.def)
++ return -ENOMEM;
++
++ dev->phy_dev = of_phy_connect(dev->ndev, phy_handle,
++ &emac_adjust_link, phy_flags,
++ PHY_INTERFACE_MODE_RGMII);
++ if (!dev->phy_dev) {
++ dev_err(&dev->ofdev->dev, "failed to connect to PHY.\n");
++ return -ENODEV;
++ }
++
++ dev->phy.def->phy_id = dev->phy_dev->drv->phy_id;
++ dev->phy.def->phy_id_mask = dev->phy_dev->drv->phy_id_mask;
++ dev->phy.def->name = dev->phy_dev->drv->name;
++ dev->phy.def->ops = &emac_dt_mdio_phy_ops;
++ dev->phy.features = dev->phy_dev->supported;
++ dev->phy.address = dev->phy_dev->mdio.addr;
++ dev->phy.mode = dev->phy_dev->interface;
++ return 0;
++}
++
++static int emac_probe_dt_phy(struct emac_instance *dev)
++{
++ struct device_node *np = dev->ofdev->dev.of_node;
++ struct device_node *phy_handle;
++ int res = 0;
++
++ phy_handle = of_parse_phandle(np, "phy-handle", 0);
++
++ if (phy_handle) {
++ res = emac_dt_mdio_probe(dev);
++ if (!res) {
++ res = emac_dt_phy_probe(dev, phy_handle);
++ if (!res)
++ res = 1;
++ else
++ mdiobus_unregister(dev->mii_bus);
++ }
++ }
++
++ of_node_put(phy_handle);
++ /* if no phy device was specified in the device tree, then we fallback
++ * to the old emac_phy.c probe code for compatibility reasons.
++ */
++ return res;
++}
++
+ static int emac_init_phy(struct emac_instance *dev)
+ {
+ struct device_node *np = dev->ofdev->dev.of_node;
+@@ -2492,6 +2716,22 @@ static int emac_init_phy(struct emac_ins
+
+ emac_configure(dev);
+
++ if (emac_has_feature(dev, EMAC_FTR_HAS_RGMII)) {
++ int res = emac_probe_dt_phy(dev);
++
++ if (res == 1) {
++ mutex_unlock(&emac_phy_map_lock);
++ goto init_phy;
++ } else if (res < 0) {
++ mutex_unlock(&emac_phy_map_lock);
++ dev_err(&dev->ofdev->dev, "failed to attach dt phy (%d).\n",
++ res);
++ return res;
++ }
++
++ /* continue with old code */
++ }
++
+ if (dev->phy_address != 0xffffffff)
+ phy_map = ~(1 << dev->phy_address);
+
+@@ -2519,6 +2759,7 @@ static int emac_init_phy(struct emac_ins
+ return -ENXIO;
+ }
+
++ init_phy:
+ /* Init PHY */
+ if (dev->phy.def->ops->init)
+ dev->phy.def->ops->init(&dev->phy);
+@@ -2987,6 +3228,12 @@ static int emac_remove(struct platform_d
+ if (emac_has_feature(dev, EMAC_FTR_HAS_ZMII))
+ zmii_detach(dev->zmii_dev, dev->zmii_port);
+
++ if (dev->phy_dev)
++ phy_disconnect(dev->phy_dev);
++
++ if (dev->mii_bus)
++ mdiobus_unregister(dev->mii_bus);
++
+ busy_phy_map &= ~(1 << dev->phy.address);
+ DBG(dev, "busy_phy_map now %#x" NL, busy_phy_map);
+
+--- a/drivers/net/ethernet/ibm/emac/core.h
++++ b/drivers/net/ethernet/ibm/emac/core.h
+@@ -199,6 +199,10 @@ struct emac_instance {
+ struct emac_instance *mdio_instance;
+ struct mutex mdio_lock;
+
++ /* Device-tree based phy configuration */
++ struct mii_bus *mii_bus;
++ struct phy_device *phy_dev;
++
+ /* ZMII infos if any */
+ u32 zmii_ph;
+ u32 zmii_port;
diff --git a/target/linux/apm821xx/patches-4.9/801-usb-xhci-add-firmware-loader-for-uPD720201-and-uPD72.patch b/target/linux/apm821xx/patches-4.9/801-usb-xhci-add-firmware-loader-for-uPD720201-and-uPD72.patch
new file mode 100644
index 0000000000..be5cb838aa
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/801-usb-xhci-add-firmware-loader-for-uPD720201-and-uPD72.patch
@@ -0,0 +1,545 @@
+From 419992bae5aaa4e06402e0b7c79fcf7bcb6b4764 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@googlemail.com>
+Date: Thu, 2 Jun 2016 00:48:46 +0200
+Subject: [PATCH] usb: xhci: add firmware loader for uPD720201 and uPD720202
+ w/o ROM
+
+This patch adds a firmware loader for the uPD720201K8-711-BAC-A
+and uPD720202K8-711-BAA-A variant. Both of these chips are listed
+in Renesas' R19UH0078EJ0500 Rev.5.00 "User's Manual: Hardware" as
+devices which need the firmware loader on page 2 in order to
+work as they "do not support the External ROM".
+
+The "Firmware Download Sequence" is describe in chapter
+"7.1 FW Download Interface" R19UH0078EJ0500 Rev.5.00 page 131.
+
+The firmware "K2013080.mem" is available from a USB3.0 Host to
+PCIe Adapter (PP2U-E card) "Firmware download" archive. An
+alternative version can be sourced from Netgear's WNDR4700 GPL
+archives.
+
+The release notes of the PP2U-E's "Firmware Download" ver 2.0.1.3
+(2012-06-15) state that the firmware is for the following devices:
+ - uPD720201 ES 2.0 sample whose revision ID is 2.
+ - uPD720201 ES 2.1 sample & CS sample & Mass product, ID is 3.
+ - uPD720202 ES 2.0 sample & CS sample & Mass product, ID is 2.
+
+If someone from Renesas is listening: It would be great, if these
+firmwares could be added to linux-firmware.git.
+
+Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
+Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
+---
+ drivers/usb/host/xhci-pci.c | 492 ++++++++++++++++++++++++++++++++++++++++++++
+ 1 file changed, 492 insertions(+)
+
+--- a/drivers/usb/host/xhci-pci.c
++++ b/drivers/usb/host/xhci-pci.c
+@@ -24,6 +24,8 @@
+ #include <linux/slab.h>
+ #include <linux/module.h>
+ #include <linux/acpi.h>
++#include <linux/firmware.h>
++#include <asm/unaligned.h>
+
+ #include "xhci.h"
+ #include "xhci-trace.h"
+@@ -221,6 +223,458 @@ static void xhci_pme_acpi_rtd3_enable(st
+ static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { }
+ #endif /* CONFIG_ACPI */
+
++static const struct renesas_fw_entry {
++ const char *firmware_name;
++ u16 device;
++ u8 revision;
++ u16 expected_version;
++} renesas_fw_table[] = {
++ /*
++ * Only the uPD720201K8-711-BAC-A or uPD720202K8-711-BAA-A
++ * are listed in R19UH0078EJ0500 Rev.5.00 as devices which
++ * need the software loader.
++ *
++ * PP2U/ReleaseNote_USB3-201-202-FW.txt:
++ *
++ * Note: This firmware is for the following devices.
++ * - uPD720201 ES 2.0 sample whose revision ID is 2.
++ * - uPD720201 ES 2.1 sample & CS sample & Mass product, ID is 3.
++ * - uPD720202 ES 2.0 sample & CS sample & Mass product, ID is 2.
++ */
++ { "K2013080.mem", 0x0014, 0x02, 0x2013 },
++ { "K2013080.mem", 0x0014, 0x03, 0x2013 },
++ { "K2013080.mem", 0x0015, 0x02, 0x2013 },
++};
++
++static const struct renesas_fw_entry *renesas_needs_fw_dl(struct pci_dev *dev)
++{
++ const struct renesas_fw_entry *entry;
++ size_t i;
++
++ /* This loader will only work with a RENESAS device. */
++ if (!(dev->vendor == PCI_VENDOR_ID_RENESAS))
++ return NULL;
++
++ for (i = 0; i < ARRAY_SIZE(renesas_fw_table); i++) {
++ entry = &renesas_fw_table[i];
++ if (entry->device == dev->device &&
++ entry->revision == dev->revision)
++ return entry;
++ }
++
++ return NULL;
++}
++
++static int renesas_fw_download_image(struct pci_dev *dev,
++ const u32 *fw,
++ size_t step)
++{
++ size_t i;
++ int err;
++ u8 fw_status;
++ bool data0_or_data1;
++
++ /*
++ * The hardware does alternate between two 32-bit pages.
++ * (This is because each row of the firmware is 8 bytes).
++ *
++ * for even steps we use DATA0, for odd steps DATA1.
++ */
++ data0_or_data1 = (step & 1) == 1;
++
++ /* step+1. Read "Set DATAX" and confirm it is cleared. */
++ for (i = 0; i < 10000; i++) {
++ err = pci_read_config_byte(dev, 0xF5, &fw_status);
++ if (err)
++ return pcibios_err_to_errno(err);
++ if (!(fw_status & BIT(data0_or_data1)))
++ break;
++
++ udelay(1);
++ }
++ if (i == 10000)
++ return -ETIMEDOUT;
++
++ /*
++ * step+2. Write FW data to "DATAX".
++ * "LSB is left" => force little endian
++ */
++ err = pci_write_config_dword(dev, data0_or_data1 ? 0xFC : 0xF8,
++ (__force u32) cpu_to_le32(fw[step]));
++ if (err)
++ return pcibios_err_to_errno(err);
++
++ udelay(100);
++
++ /* step+3. Set "Set DATAX". */
++ err = pci_write_config_byte(dev, 0xF5, BIT(data0_or_data1));
++ if (err)
++ return pcibios_err_to_errno(err);
++
++ return 0;
++}
++
++static int renesas_fw_verify(struct pci_dev *dev,
++ const void *fw_data,
++ size_t length)
++{
++ const struct renesas_fw_entry *entry = renesas_needs_fw_dl(dev);
++ u16 fw_version_pointer;
++ u16 fw_version;
++
++ if (!entry)
++ return -EINVAL;
++
++ /*
++ * The Firmware's Data Format is describe in
++ * "6.3 Data Format" R19UH0078EJ0500 Rev.5.00 page 124
++ */
++
++ /* "Each row is 8 bytes". => firmware size must be a multiple of 8. */
++ if (length % 8 != 0) {
++ dev_err(&dev->dev, "firmware size is not a multipe of 8.");
++ return -EINVAL;
++ }
++
++ /*
++ * The bootrom chips of the big brother have sizes up to 64k, let's
++ * assume that's the biggest the firmware can get.
++ */
++ if (length < 0x1000 || length >= 0x10000) {
++ dev_err(&dev->dev, "firmware is size %zd is not (4k - 64k).",
++ length);
++ return -EINVAL;
++ }
++
++ /* The First 2 bytes are fixed value (55aa). "LSB on Left" */
++ if (get_unaligned_le16(fw_data) != 0x55aa) {
++ dev_err(&dev->dev, "no valid firmware header found.");
++ return -EINVAL;
++ }
++
++ /* verify the firmware version position and print it. */
++ fw_version_pointer = get_unaligned_le16(fw_data + 4);
++ if (fw_version_pointer + 2 >= length) {
++ dev_err(&dev->dev, "firmware version pointer is outside of the firmware image.");
++ return -EINVAL;
++ }
++
++ fw_version = get_unaligned_le16(fw_data + fw_version_pointer);
++ dev_dbg(&dev->dev, "got firmware version: %02x.", fw_version);
++
++ if (fw_version != entry->expected_version) {
++ dev_err(&dev->dev, "firmware version mismatch, expected version: %02x.",
++ entry->expected_version);
++ return -EINVAL;
++ }
++
++ return 0;
++}
++
++static int renesas_fw_check_running(struct pci_dev *pdev)
++{
++ int err;
++ u8 fw_state;
++
++ /*
++ * Test if the device is actually needing the firmware. As most
++ * BIOSes will initialize the device for us. If the device is
++ * initialized.
++ */
++ err = pci_read_config_byte(pdev, 0xF4, &fw_state);
++ if (err)
++ return pcibios_err_to_errno(err);
++
++ /*
++ * Check if "FW Download Lock" is locked. If it is and the FW is
++ * ready we can simply continue. If the FW is not ready, we have
++ * to give up.
++ */
++ if (fw_state & BIT(1)) {
++ dev_dbg(&pdev->dev, "FW Download Lock is engaged.");
++
++ if (fw_state & BIT(4))
++ return 0;
++
++ dev_err(&pdev->dev, "FW Download Lock is set and FW is not ready. Giving Up.");
++ return -EIO;
++ }
++
++ /*
++ * Check if "FW Download Enable" is set. If someone (us?) tampered
++ * with it and it can't be resetted, we have to give up too... and
++ * ask for a forgiveness and a reboot.
++ */
++ if (fw_state & BIT(0)) {
++ dev_err(&pdev->dev, "FW Download Enable is stale. Giving Up (poweroff/reboot needed).");
++ return -EIO;
++ }
++
++ /* Otherwise, Check the "Result Code" Bits (6:4) and act accordingly */
++ switch ((fw_state & 0x70)) {
++ case 0: /* No result yet */
++ dev_dbg(&pdev->dev, "FW is not ready/loaded yet.");
++
++ /* tell the caller, that this device needs the firmware. */
++ return 1;
++
++ case BIT(4): /* Success, device should be working. */
++ dev_dbg(&pdev->dev, "FW is ready.");
++ return 0;
++
++ case BIT(5): /* Error State */
++ dev_err(&pdev->dev, "hardware is in an error state. Giving up (poweroff/reboot needed).");
++ return -ENODEV;
++
++ default: /* All other states are marked as "Reserved states" */
++ dev_err(&pdev->dev, "hardware is in an invalid state %x. Giving up (poweroff/reboot needed).",
++ (fw_state & 0x70) >> 4);
++ return -EINVAL;
++ }
++}
++
++static int renesas_hw_check_run_stop_busy(struct pci_dev *pdev)
++{
++#if 0
++ u32 val;
++
++ /*
++ * 7.1.3 Note 3: "... must not set 'FW Download Enable' when
++ * 'RUN/STOP' of USBCMD Register is set"
++ */
++ val = readl(hcd->regs + 0x20);
++ if (val & BIT(0)) {
++ dev_err(&pdev->dev, "hardware is busy and can't receive a FW.");
++ return -EBUSY;
++ }
++#endif
++ return 0;
++}
++
++static int renesas_fw_download(struct pci_dev *pdev,
++ const struct firmware *fw, unsigned int retry_counter)
++{
++ const u32 *fw_data = (const u32 *) fw->data;
++ size_t i;
++ int err;
++ u8 fw_status;
++
++ /*
++ * For more information and the big picture: please look at the
++ * "Firmware Download Sequence" in "7.1 FW Download Interface"
++ * of R19UH0078EJ0500 Rev.5.00 page 131
++ */
++ err = renesas_hw_check_run_stop_busy(pdev);
++ if (err)
++ return err;
++
++ /*
++ * 0. Set "FW Download Enable" bit in the
++ * "FW Download Control & Status Register" at 0xF4
++ */
++ err = pci_write_config_byte(pdev, 0xF4, BIT(0));
++ if (err)
++ return pcibios_err_to_errno(err);
++
++ /* 1 - 10 follow one step after the other. */
++ for (i = 0; i < fw->size / 4; i++) {
++ err = renesas_fw_download_image(pdev, fw_data, i);
++ if (err) {
++ dev_err(&pdev->dev, "Firmware Download Step %zd failed at position %zd bytes with (%d).",
++ i, i * 4, err);
++ return err;
++ }
++ }
++
++ /*
++ * This sequence continues until the last data is written to
++ * "DATA0" or "DATA1". Naturally, we wait until "SET DATA0/1"
++ * is cleared by the hardware beforehand.
++ */
++ for (i = 0; i < 10000; i++) {
++ err = pci_read_config_byte(pdev, 0xF5, &fw_status);
++ if (err)
++ return pcibios_err_to_errno(err);
++ if (!(fw_status & (BIT(0) | BIT(1))))
++ break;
++
++ udelay(1);
++ }
++ if (i == 10000)
++ dev_warn(&pdev->dev, "Final Firmware Download step timed out.");
++
++ /*
++ * 11. After finishing writing the last data of FW, the
++ * System Software must clear "FW Download Enable"
++ */
++ err = pci_write_config_byte(pdev, 0xF4, 0);
++ if (err)
++ return pcibios_err_to_errno(err);
++
++ /* 12. Read "Result Code" and confirm it is good. */
++ for (i = 0; i < 10000; i++) {
++ err = pci_read_config_byte(pdev, 0xF4, &fw_status);
++ if (err)
++ return pcibios_err_to_errno(err);
++ if (fw_status & BIT(4))
++ break;
++
++ udelay(1);
++ }
++ if (i == 10000) {
++ /* Timed out / Error - let's see if we can fix this */
++ err = renesas_fw_check_running(pdev);
++ switch (err) {
++ case 0: /*
++ * we shouldn't end up here.
++ * maybe it took a little bit longer.
++ * But all should be well?
++ */
++ break;
++
++ case 1: /* (No result yet? - we can try to retry) */
++ if (retry_counter < 10) {
++ retry_counter++;
++ dev_warn(&pdev->dev, "Retry Firmware download: %d try.",
++ retry_counter);
++ return renesas_fw_download(pdev, fw,
++ retry_counter);
++ }
++ return -ETIMEDOUT;
++
++ default:
++ return err;
++ }
++ }
++ /*
++ * Optional last step: Engage Firmware Lock
++ *
++ * err = pci_write_config_byte(pdev, 0xF4, BIT(2));
++ * if (err)
++ * return pcibios_err_to_errno(err);
++ */
++
++ return 0;
++}
++
++struct renesas_fw_ctx {
++ struct pci_dev *pdev;
++ const struct pci_device_id *id;
++ bool resume;
++};
++
++static int xhci_pci_probe(struct pci_dev *pdev,
++ const struct pci_device_id *id);
++
++static void renesas_fw_callback(const struct firmware *fw,
++ void *context)
++{
++ struct renesas_fw_ctx *ctx = context;
++ struct pci_dev *pdev = ctx->pdev;
++ struct device *parent = pdev->dev.parent;
++ int err = -ENOENT;
++
++ if (fw) {
++ err = renesas_fw_verify(pdev, fw->data, fw->size);
++ if (!err) {
++ err = renesas_fw_download(pdev, fw, 0);
++ release_firmware(fw);
++ if (!err) {
++ if (ctx->resume)
++ return;
++
++ err = xhci_pci_probe(pdev, ctx->id);
++ if (!err) {
++ /* everything worked */
++ devm_kfree(&pdev->dev, ctx);
++ return;
++ }
++
++ /* in case of an error - fall through */
++ } else {
++ dev_err(&pdev->dev, "firmware failed to download (%d).",
++ err);
++ }
++ }
++ } else {
++ dev_err(&pdev->dev, "firmware failed to load (%d).", err);
++ }
++
++ dev_info(&pdev->dev, "Unloading driver");
++
++ if (parent)
++ device_lock(parent);
++
++ device_release_driver(&pdev->dev);
++
++ if (parent)
++ device_unlock(parent);
++
++ pci_dev_put(pdev);
++}
++
++static int renesas_fw_alive_check(struct pci_dev *pdev)
++{
++ const struct renesas_fw_entry *entry;
++ int err;
++
++ /* check if we have a eligible RENESAS' uPD720201/2 w/o FW. */
++ entry = renesas_needs_fw_dl(pdev);
++ if (!entry)
++ return 0;
++
++ err = renesas_fw_check_running(pdev);
++ /* Also go ahead, if the firmware is running */
++ if (err == 0)
++ return 0;
++
++ /* At this point, we can be sure that the FW isn't ready. */
++ return err;
++}
++
++static int renesas_fw_download_to_hw(struct pci_dev *pdev,
++ const struct pci_device_id *id,
++ bool do_resume)
++{
++ const struct renesas_fw_entry *entry;
++ struct renesas_fw_ctx *ctx;
++ int err;
++
++ /* check if we have a eligible RENESAS' uPD720201/2 w/o FW. */
++ entry = renesas_needs_fw_dl(pdev);
++ if (!entry)
++ return 0;
++
++ err = renesas_fw_check_running(pdev);
++ /* Continue ahead, if the firmware is already running. */
++ if (err == 0)
++ return 0;
++
++ if (err != 1)
++ return err;
++
++ ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
++ if (!ctx)
++ return -ENOMEM;
++ ctx->pdev = pdev;
++ ctx->resume = do_resume;
++ ctx->id = id;
++
++ pci_dev_get(pdev);
++ err = request_firmware_nowait(THIS_MODULE, 1, entry->firmware_name,
++ &pdev->dev, GFP_KERNEL, ctx, renesas_fw_callback);
++ if (err) {
++ pci_dev_put(pdev);
++ return err;
++ }
++
++ /*
++ * The renesas_fw_callback() callback will continue the probe
++ * process, once it aquires the firmware.
++ */
++ return 1;
++}
++
+ /* called during probe() after chip reset completes */
+ static int xhci_pci_setup(struct usb_hcd *hcd)
+ {
+@@ -260,6 +714,22 @@ static int xhci_pci_probe(struct pci_dev
+ struct hc_driver *driver;
+ struct usb_hcd *hcd;
+
++ /*
++ * Check if this device is a RENESAS uPD720201/2 device.
++ * Otherwise, we can continue with xhci_pci_probe as usual.
++ */
++ retval = renesas_fw_download_to_hw(dev, id, false);
++ switch (retval) {
++ case 0:
++ break;
++
++ case 1: /* let it load the firmware and recontinue the probe. */
++ return 0;
++
++ default:
++ return retval;
++ };
++
+ driver = (struct hc_driver *)id->driver_data;
+
+ /* Prevent runtime suspending between USB-2 and USB-3 initialization */
+@@ -317,6 +787,16 @@ static void xhci_pci_remove(struct pci_d
+ {
+ struct xhci_hcd *xhci;
+
++ if (renesas_fw_alive_check(dev)) {
++ /*
++ * bail out early, if this was a renesas device w/o FW.
++ * Else we might hit the NMI watchdog in xhci_handsake
++ * during xhci_reset as part of the driver's unloading.
++ * which we forced in the renesas_fw_callback().
++ */
++ return;
++ }
++
+ xhci = hcd_to_xhci(pci_get_drvdata(dev));
+ xhci->xhc_state |= XHCI_STATE_REMOVING;
+ if (xhci->shared_hcd) {
diff --git a/target/linux/apm821xx/patches-4.9/802-usb-xhci-force-msi-renesas-xhci.patch b/target/linux/apm821xx/patches-4.9/802-usb-xhci-force-msi-renesas-xhci.patch
new file mode 100644
index 0000000000..a201d79104
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/802-usb-xhci-force-msi-renesas-xhci.patch
@@ -0,0 +1,54 @@
+From a0dc613140bab907a3d5787a7ae7b0638bf674d0 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Thu, 23 Jun 2016 20:28:20 +0200
+Subject: [PATCH] usb: xhci: force MSI for uPD720201 and
+ uPD720202
+
+The APM82181 does not support MSI-X. When probed, it will
+produce a noisy warning.
+
+---
+ drivers/usb/host/pci-quirks.c | 362 ++++++++++++++++++++++++++++++++++++++++++
+ 1 file changed, 362 insertions(+)
+
+--- a/drivers/usb/host/xhci-pci.c
++++ b/drivers/usb/host/xhci-pci.c
+@@ -188,7 +188,7 @@ static void xhci_pci_quirks(struct devic
+ }
+ if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
+ pdev->device == 0x0015)
+- xhci->quirks |= XHCI_RESET_ON_RESUME;
++ xhci->quirks |= XHCI_RESET_ON_RESUME | XHCI_FORCE_MSI;
+ if (pdev->vendor == PCI_VENDOR_ID_VIA)
+ xhci->quirks |= XHCI_RESET_ON_RESUME;
+
+--- a/drivers/usb/host/xhci.c
++++ b/drivers/usb/host/xhci.c
+@@ -387,10 +387,14 @@ static int xhci_try_enable_msi(struct us
+ free_irq(hcd->irq, hcd);
+ hcd->irq = 0;
+
+- ret = xhci_setup_msix(xhci);
+- if (ret)
+- /* fall back to msi*/
++ if (xhci->quirks & XHCI_FORCE_MSI) {
+ ret = xhci_setup_msi(xhci);
++ } else {
++ ret = xhci_setup_msix(xhci);
++ if (ret)
++ /* fall back to msi*/
++ ret = xhci_setup_msi(xhci);
++ }
+
+ if (!ret)
+ /* hcd->irq is 0, we have MSI */
+--- a/drivers/usb/host/xhci.h
++++ b/drivers/usb/host/xhci.h
+@@ -1674,6 +1674,7 @@ struct xhci_hcd {
+ /* support xHCI 0.96 spec USB2 software LPM */
+ unsigned sw_lpm_support:1;
+ /* support xHCI 1.0 spec USB2 hardware LPM */
++#define XHCI_FORCE_MSI (1 << 24)
+ unsigned hw_lpm_support:1;
+ /* cached usb2 extened protocol capabilites */
+ u32 *ext_caps;
diff --git a/target/linux/apm821xx/patches-4.9/804-usb-dwc2-add-amcc-usb-otg-405ex.patch b/target/linux/apm821xx/patches-4.9/804-usb-dwc2-add-amcc-usb-otg-405ex.patch
new file mode 100644
index 0000000000..3dd2ed5734
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/804-usb-dwc2-add-amcc-usb-otg-405ex.patch
@@ -0,0 +1,48 @@
+--- a/drivers/usb/dwc2/platform.c
++++ b/drivers/usb/dwc2/platform.c
+@@ -279,6 +279,37 @@ static int dwc2_get_dr_mode(struct dwc2_
+ return 0;
+ }
+
++static const struct dwc2_core_params params_amcc_dwc_otg = {
++ .otg_cap = DWC2_CAP_PARAM_HNP_SRP_CAPABLE,
++ .otg_ver = -1,
++ .dma_enable = -1,
++ .dma_desc_enable = -1,
++ .speed = -1,
++ .enable_dynamic_fifo = -1,
++ .en_multiple_tx_fifo = -1,
++ .host_rx_fifo_size = -1,
++ .host_nperio_tx_fifo_size = -1,
++ .host_perio_tx_fifo_size = -1,
++ .max_transfer_size = -1,
++ .max_packet_count = -1,
++ .host_channels = -1,
++ .phy_type = -1,
++ .phy_utmi_width = -1,
++ .phy_ulpi_ddr = -1,
++ .phy_ulpi_ext_vbus = -1,
++ .i2c_enable = -1,
++ .ulpi_fs_ls = -1,
++ .host_support_fs_ls_low_power = -1,
++ .host_ls_low_power_phy_clk = -1,
++ .ts_dline = -1,
++ .reload_ctl = -1,
++ .ahbcfg = GAHBCFG_HBSTLEN_INCR16 <<
++ GAHBCFG_HBSTLEN_SHIFT,
++ .uframe_sched = -1,
++ .external_id_pin_ctl = -1,
++ .hibernation = -1,
++};
++
+ static int __dwc2_lowlevel_hw_enable(struct dwc2_hsotg *hsotg)
+ {
+ struct platform_device *pdev = to_platform_device(hsotg->dev);
+@@ -511,6 +542,7 @@ static void dwc2_driver_shutdown(struct
+ }
+
+ static const struct of_device_id dwc2_of_match_table[] = {
++ { .compatible = "amcc,usb-otg-405ex", .data = &params_amcc_dwc_otg },
+ { .compatible = "brcm,bcm2835-usb", .data = &params_bcm2835 },
+ { .compatible = "hisilicon,hi6220-usb", .data = &params_hi6220 },
+ { .compatible = "rockchip,rk3066-usb", .data = &params_rk3066 },
diff --git a/target/linux/apm821xx/patches-4.9/901-hwmon-add-driver-for-Microchip-TC654-TC655-PWM-fan-c.patch b/target/linux/apm821xx/patches-4.9/901-hwmon-add-driver-for-Microchip-TC654-TC655-PWM-fan-c.patch
new file mode 100644
index 0000000000..ceacde9dda
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.9/901-hwmon-add-driver-for-Microchip-TC654-TC655-PWM-fan-c.patch
@@ -0,0 +1,1027 @@
+From 5ea2e152d846bf60901107fefd81a58f792f3bc2 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Fri, 10 Jun 2016 03:00:46 +0200
+Subject: [PATCH] hwmon: add driver for Microchip TC654/TC655 PWM fan
+ controllers
+
+This patch adds a hwmon driver for the Microchip TC654 and TC655
+Dual SMBus PWM Fan Speed Controllers with Fan Fault detection.
+
+The chip is described in the DS2001734C Spec Document from Microchip.
+It supports:
+ - Shared PWM Fan Drive for two fans
+ - Provides RPM
+ - automatic PWM controller (needs additional
+ NTC/PTC Thermistors.)
+ - Overtemperature alarm (when using NTC/PTC
+ Thermistors)
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+---
+ drivers/hwmon/Kconfig | 10 +
+ drivers/hwmon/Makefile | 1 +
+ drivers/hwmon/tc654.c | 969 +++++++++++++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 980 insertions(+)
+ create mode 100644 drivers/hwmon/tc654.c
+
+--- a/drivers/hwmon/Kconfig
++++ b/drivers/hwmon/Kconfig
+@@ -1549,6 +1549,16 @@ config SENSORS_INA3221
+ This driver can also be built as a module. If so, the module
+ will be called ina3221.
+
++config SENSORS_TC654
++ tristate "Microchip TC654 and TC655"
++ depends on I2C
++ help
++ If you say yes here you get support for Microchip TC655 and TC654
++ Dual PWM Fan Speed Controllers and sensor chips.
++
++ This driver can also be built as a module. If so, the module
++ will be called tc654.
++
+ config SENSORS_TC74
+ tristate "Microchip TC74"
+ depends on I2C
+--- a/drivers/hwmon/Makefile
++++ b/drivers/hwmon/Makefile
+@@ -148,6 +148,7 @@ obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc4
+ obj-$(CONFIG_SENSORS_SMSC47M1) += smsc47m1.o
+ obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
+ obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o
++obj-$(CONFIG_SENSORS_TC654) += tc654.o
+ obj-$(CONFIG_SENSORS_TC74) += tc74.o
+ obj-$(CONFIG_SENSORS_THMC50) += thmc50.o
+ obj-$(CONFIG_SENSORS_TMP102) += tmp102.o
+--- /dev/null
++++ b/drivers/hwmon/tc654.c
+@@ -0,0 +1,969 @@
++/*
++ * tc654.c - Support for Microchip TC654/TC655
++ * "A Dual SMBus PWM FAN Speed Controllers with Fan Fault Detection"
++ *
++ * Copyright (c) 2016 Christian Lamparter <chunkeey@gmail.com>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation version 2 of the License.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * The chip is described in the DS2001734C Spec Document from Microchip.
++ */
++
++#include <linux/module.h>
++#include <linux/init.h>
++#include <linux/slab.h>
++#include <linux/jiffies.h>
++#include <linux/i2c.h>
++#include <linux/hwmon.h>
++#include <linux/hwmon-sysfs.h>
++#include <linux/err.h>
++#include <linux/mutex.h>
++#include <linux/thermal.h>
++
++/* Hardware definitions */
++/* 5.1.4 Address Byte stats that TC654/TC655 are fixed at 0x1b */
++static const unsigned short normal_i2c[] = { 0x1b, I2C_CLIENT_END };
++
++enum TC654_REGS {
++ TC654_REG_RPM1 = 0x00,
++ TC654_REG_RPM2,
++ TC654_REG_FAN1_FAULT_THRESH,
++ TC654_REG_FAN2_FAULT_THRESH,
++ TC654_REG_CONFIG,
++ TC654_REG_STATUS,
++ TC654_REG_DUTY_CYCLE,
++ TC654_REG_MFR_ID,
++ TC654_REG_VER_ID,
++
++ /* keep last */
++ __TC654_REG_NUM,
++};
++
++#define TC654_MFR_ID_MICROCHIP 0x84
++#define TC654_VER_ID 0x00
++#define TC655_VER_ID 0x01
++
++enum TC654_CONTROL_BITS {
++ TC654_CTRL_SDM = BIT(0),
++ TC654_CTRL_F1PPR_S = 1,
++ TC654_CTRL_F1PPR_M = (BIT(1) | BIT(2)),
++ TC654_CTRL_F2PPR_S = 3,
++ TC654_CTRL_F2PPR_M = (BIT(3) | BIT(4)),
++ TC654_CTRL_DUTYC = BIT(5),
++ TC654_CTRL_RES = BIT(6),
++ TC654_CTRL_FFCLR = BIT(7),
++};
++
++enum TC654_STATUS_BITS {
++ TC654_STATUS_F1F = BIT(0),
++ TC654_STATUS_F2F = BIT(1),
++ TC654_STATUS_VSTAT = BIT(2),
++ TC654_STATUS_R1CO = BIT(3),
++ TC654_STATUS_R2CO = BIT(4),
++ TC654_STATUS_OTF = BIT(5),
++};
++
++enum TC654_FAN {
++ TC654_FAN1 = 0,
++ TC654_FAN2,
++
++ /* keep last */
++ __NUM_TC654_FAN,
++};
++
++enum TC654_FAN_MODE {
++ TC654_PWM_OFF, /* Shutdown Mode - switch of both fans */
++ TC654_PWM_VIN, /* Fans will be controlled via V_in analog input pin */
++ TC654_PWM_3000, /* sets fans to 30% duty cycle */
++ TC654_PWM_3467,
++ TC654_PWM_3933, /* default case - if V_in pin is open */
++ TC654_PWM_4400,
++ TC654_PWM_4867,
++ TC654_PWM_5333,
++ TC654_PWM_5800,
++ TC654_PWM_6267,
++ TC654_PWM_6733,
++ TC654_PWM_7200,
++ TC654_PWM_7667,
++ TC654_PWM_8133,
++ TC654_PWM_8600,
++ TC654_PWM_9067,
++ TC654_PWM_9533,
++ TC654_PWM_10000, /* sets fans to 100% duty cycle */
++};
++
++enum TC654_ALARMS {
++ TC654_ALARM_FAN1_FAULT,
++ TC654_ALARM_FAN2_FAULT,
++ TC654_ALARM_FAN1_COUNTER_OVERFLOW,
++ TC654_ALARM_FAN2_COUNTER_OVERFLOW,
++ TC654_ALARM_OVER_TEMPERATURE,
++
++ /* KEEP LAST */
++ __NUM_TC654_ALARMS,
++};
++
++static const struct pwm_table_entry {
++ u8 min;
++ enum TC654_FAN_MODE mode;
++} pwm_table[] = {
++ { 0, TC654_PWM_OFF },
++ { 1, TC654_PWM_3000 },
++ { 88, TC654_PWM_3467 },
++ {101, TC654_PWM_3933 },
++ {113, TC654_PWM_4400 },
++ {125, TC654_PWM_4867 },
++ {137, TC654_PWM_5333 },
++ {148, TC654_PWM_5800 },
++ {160, TC654_PWM_6267 },
++ {172, TC654_PWM_6733 },
++ {184, TC654_PWM_7200 },
++ {196, TC654_PWM_7667 },
++ {208, TC654_PWM_8133 },
++ {220, TC654_PWM_8600 },
++ {232, TC654_PWM_9067 },
++ {244, TC654_PWM_9533 },
++ {255, TC654_PWM_10000 },
++};
++
++/* driver context */
++struct tc654 {
++ struct i2c_client *client;
++
++ struct mutex update_lock;
++
++ unsigned long last_updated; /* in jiffies */
++ u8 cached_regs[__TC654_REG_NUM];
++
++ bool valid; /* monitored registers are valid */
++ u16 fan_input[__NUM_TC654_FAN];
++ bool alarms[__NUM_TC654_ALARMS];
++ bool vin_status;
++ bool pwm_manual;
++
++ /* optional cooling device */
++ struct thermal_cooling_device *cdev;
++};
++
++/* hardware accessors and functions */
++static int read_tc(struct tc654 *tc, u8 reg)
++{
++ s32 status;
++
++ if (reg <= TC654_REG_VER_ID) {
++ /* Table 6.1 states that all registers are readable */
++ status = i2c_smbus_read_byte_data(tc->client, reg);
++ } else
++ status = -EINVAL;
++
++ if (status < 0) {
++ dev_warn(&tc->client->dev, "can't read register 0x%02x due to error (%d)",
++ reg, status);
++ } else {
++ tc->cached_regs[reg] = status;
++ }
++
++ return status;
++}
++
++static int write_tc(struct tc654 *tc, u8 i2c_reg, u8 val)
++{
++ s32 status;
++
++ /*
++ * Table 6.1 states that both fan threshold registers,
++ * the Config and Duty Cycle are writeable.
++ */
++ switch (i2c_reg) {
++ case TC654_REG_FAN1_FAULT_THRESH:
++ case TC654_REG_FAN2_FAULT_THRESH:
++ case TC654_REG_DUTY_CYCLE:
++ case TC654_REG_CONFIG:
++ status = i2c_smbus_write_byte_data(tc->client, i2c_reg, val);
++ break;
++
++ default:
++ return -EINVAL;
++ }
++
++ if (status < 0) {
++ dev_warn(&tc->client->dev, "can't write register 0x%02x with value 0x%02x due to error (%d)",
++ i2c_reg, val, status);
++ } else {
++ tc->cached_regs[i2c_reg] = val;
++ }
++
++ return status;
++}
++
++static int mod_config(struct tc654 *tc, u8 set, u8 clear)
++{
++ u8 val = 0;
++
++ /* a bit can't be set and cleared on the same time. */
++ if (set & clear)
++ return -EINVAL;
++
++ /* invalidate data to force re-read from hardware */
++ tc->valid = false;
++ val = (tc->cached_regs[TC654_REG_CONFIG] | set) & (~clear);
++ return write_tc(tc, TC654_REG_CONFIG, val);
++}
++
++static int read_fan_rpm(struct tc654 *tc, enum TC654_FAN fan)
++{
++ int ret;
++
++ /* 6.1 RPM-OUTPUT1 and RPM-OUTPUT2 registers */
++ ret = read_tc(tc, fan == TC654_FAN1 ? TC654_REG_RPM1 : TC654_REG_RPM2);
++ if (ret < 0)
++ return ret;
++
++ /*
++ * The Resolution Selection Bit in 6.3 CONFIGURATION REGISTER
++ * is needed to convert the raw value to the RPM.
++ * 0 = RPM1 and RPM2 use (8-Bit) resolution => * 50 RPM
++ * 1 = RPM1 and RPM2 use (9-Bit) resolution => * 25 RPM
++ */
++ return ret * (25 <<
++ !(tc->cached_regs[TC654_REG_CONFIG] & TC654_CTRL_RES));
++}
++
++static int write_fan_fault_thresh(struct tc654 *tc, enum TC654_FAN fan,
++ u16 rpm)
++{
++ u8 converted_rpm;
++
++ if (rpm > 12750)
++ return -EINVAL;
++
++ /*
++ * 6.2 FAN_FAULT1 and FAN_FAULT2 Threshold registers
++ *
++ * Both registers operate in 50 RPM mode exclusively.
++ */
++ converted_rpm = rpm / 50;
++
++ /* invalidate data to force re-read from hardware */
++ tc->valid = false;
++ return write_tc(tc, fan == TC654_FAN1 ? TC654_REG_FAN1_FAULT_THRESH :
++ TC654_REG_FAN2_FAULT_THRESH, converted_rpm);
++}
++
++
++static int read_fan_fault_thresh(struct tc654 *tc, enum TC654_FAN fan)
++{
++ /*
++ * 6.2 FAN_FAULT1 and FAN_FAULT2 Threshold registers
++ *
++ * Both registers operate in 50 RPM mode exclusively.
++ */
++ return read_tc(tc, fan == TC654_FAN1 ? TC654_REG_FAN1_FAULT_THRESH :
++ TC654_REG_FAN2_FAULT_THRESH) * 50;
++}
++
++static enum TC654_FAN_MODE get_fan_mode(struct tc654 *tc)
++{
++ if (tc->cached_regs[TC654_REG_CONFIG] & TC654_CTRL_SDM) {
++ return TC654_PWM_OFF;
++ } else if (tc->cached_regs[TC654_REG_CONFIG] & TC654_CTRL_DUTYC) {
++ return TC654_PWM_3000 + tc->cached_regs[TC654_REG_DUTY_CYCLE];
++ } else if (tc->vin_status == 0)
++ return TC654_PWM_VIN;
++
++ return -EINVAL;
++}
++
++static int write_fan_mode(struct tc654 *tc, enum TC654_FAN_MODE mode)
++{
++ int err;
++ u8 pwm_mode;
++ bool in_sdm;
++
++ in_sdm = !!(tc->cached_regs[TC654_REG_CONFIG] &
++ TC654_CTRL_SDM);
++
++ switch (mode) {
++ case TC654_PWM_OFF:
++ if (in_sdm)
++ return 0;
++
++ /* Enter Shutdown Mode - Switches off all fans */
++ err = mod_config(tc, TC654_CTRL_SDM, TC654_CTRL_DUTYC);
++ if (err)
++ return err;
++
++ return 0;
++
++ case TC654_PWM_VIN:
++ if (tc->vin_status) {
++ dev_err(&tc->client->dev,
++ "V_in pin is open, can't enable automatic mode.");
++ return -EINVAL;
++ }
++
++ err = mod_config(tc, 0, TC654_CTRL_SDM | TC654_CTRL_DUTYC);
++ if (err)
++ return err;
++
++ tc->pwm_manual = false;
++ return 0;
++
++ case TC654_PWM_3000:
++ case TC654_PWM_3467:
++ case TC654_PWM_3933:
++ case TC654_PWM_4400:
++ case TC654_PWM_4867:
++ case TC654_PWM_5333:
++ case TC654_PWM_5800:
++ case TC654_PWM_6267:
++ case TC654_PWM_6733:
++ case TC654_PWM_7200:
++ case TC654_PWM_7667:
++ case TC654_PWM_8133:
++ case TC654_PWM_8600:
++ case TC654_PWM_9067:
++ case TC654_PWM_9533:
++ case TC654_PWM_10000:
++ pwm_mode = mode - TC654_PWM_3000;
++ if (!in_sdm) {
++ err = write_tc(tc, TC654_REG_DUTY_CYCLE, pwm_mode);
++ if (err)
++ return err;
++ }
++
++ err = mod_config(tc, TC654_CTRL_DUTYC, TC654_CTRL_SDM);
++ if (err)
++ return err;
++
++ tc->pwm_manual = true;
++
++ if (in_sdm) {
++ /*
++ * In case the TC654/TC655 was in SDM mode, the write
++ * above into the TC654_REG_DUTY_CYCLE register will
++ * have no effect because the chip was switched off.
++ *
++ * Note: The TC654/TC655 have a special "power-on"
++ * feature where the PWM will be forced to 100% for
++ * one full second in order to spin-up a resting fan.
++ */
++ err = write_tc(tc, TC654_REG_DUTY_CYCLE, pwm_mode);
++ if (err)
++ return err;
++ }
++
++ return 0;
++
++ default:
++ return -EINVAL;
++ }
++}
++
++static struct tc654 *tc654_update_device(struct device *dev)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++
++ mutex_lock(&tc->update_lock);
++
++ /*
++ * In Chapter "1.0 Electrical Characteristics",
++ * the "Fault Output Response Time" is specified as 2.4 seconds.
++ */
++ if (time_after(jiffies, tc->last_updated + 2 * HZ + (HZ * 2) / 5)
++ || !tc->valid) {
++ size_t i;
++ int ret;
++ bool alarm_triggered;
++
++ tc->valid = false;
++
++ for (i = 0; i < __NUM_TC654_FAN; i++) {
++ ret = read_fan_rpm(tc, i);
++ if (ret < 0)
++ goto out;
++
++ tc->fan_input[i] = ret;
++ }
++
++ ret = read_tc(tc, TC654_REG_STATUS);
++ if (ret < 0)
++ goto out;
++
++ alarm_triggered = !!(ret & (TC654_STATUS_F1F |
++ TC654_STATUS_F2F | TC654_STATUS_R1CO |
++ TC654_STATUS_R2CO | TC654_STATUS_OTF));
++
++ tc->alarms[TC654_ALARM_FAN1_FAULT] = !!(ret & TC654_STATUS_F1F);
++ tc->alarms[TC654_ALARM_FAN2_FAULT] = !!(ret & TC654_STATUS_F2F);
++ tc->alarms[TC654_ALARM_FAN1_COUNTER_OVERFLOW] =
++ !!(ret & TC654_STATUS_R1CO);
++ tc->alarms[TC654_ALARM_FAN2_COUNTER_OVERFLOW] =
++ !!(ret & TC654_STATUS_R2CO);
++ tc->alarms[TC654_ALARM_OVER_TEMPERATURE] =
++ !!(ret & TC654_STATUS_OTF);
++ tc->vin_status = !!(ret & TC654_STATUS_VSTAT);
++
++ /*
++ * From 4.5 and 6.3
++ *
++ * ... "If the V_in pin is open when TC654_CTRL_DUTYC is not
++ * selected, then V_out duty cycle will default to 39.33%.".
++ *
++ * and most importantly 6.5:
++ * ... "V_in pin is open, the duty cycle will go to the default
++ * setting of this register, which is 0010 (39.33%)."
++ */
++ tc->pwm_manual |= tc->vin_status &&
++ (tc->cached_regs[TC654_REG_CONFIG] &
++ TC654_CTRL_DUTYC);
++
++ if (alarm_triggered) {
++ /*
++ * as the name implies, this FLAG needs to be
++ * set in order to clear the FAN Fault error.
++ */
++ ret = mod_config(tc, TC654_CTRL_FFCLR, 0);
++ if (ret < 0)
++ goto out;
++ }
++
++ tc->last_updated = jiffies;
++ tc->valid = true;
++ }
++
++out:
++ mutex_unlock(&tc->update_lock);
++ return tc;
++}
++
++static u8 get_fan_pulse(struct tc654 *tc, enum TC654_FAN fan)
++{
++ u8 fan_pulse_mask = fan == TC654_FAN1 ?
++ TC654_CTRL_F1PPR_M : TC654_CTRL_F2PPR_M;
++ u8 fan_pulse_shift = fan == TC654_FAN1 ?
++ TC654_CTRL_F1PPR_S : TC654_CTRL_F2PPR_S;
++
++ return 1 << ((tc->cached_regs[TC654_REG_CONFIG] & fan_pulse_mask) >>
++ fan_pulse_shift);
++}
++
++static int
++set_fan_pulse(struct tc654 *tc, enum TC654_FAN fan, int pulses)
++{
++ int old_pulses;
++ int err;
++ u8 new_pulse_per_rotation;
++ u8 fan_pulse_mask = fan == TC654_FAN1 ?
++ TC654_CTRL_F1PPR_M : TC654_CTRL_F2PPR_M;
++ u8 fan_pulse_shift = fan == TC654_FAN1 ?
++ TC654_CTRL_F1PPR_S : TC654_CTRL_F2PPR_S;
++
++ switch (pulses) {
++ case 1:
++ new_pulse_per_rotation = 0;
++ break;
++ case 2:
++ new_pulse_per_rotation = 1;
++ break;
++ case 4:
++ new_pulse_per_rotation = 2;
++ break;
++ case 8:
++ new_pulse_per_rotation = 3;
++ break;
++ default:
++ return -EINVAL;
++ }
++
++ new_pulse_per_rotation <<= fan_pulse_shift;
++ new_pulse_per_rotation &= fan_pulse_mask;
++
++ old_pulses = tc->cached_regs[TC654_REG_CONFIG];
++ old_pulses &= fan_pulse_mask;
++
++ if (new_pulse_per_rotation == old_pulses)
++ return 0;
++
++ mutex_lock(&tc->update_lock);
++ err = mod_config(tc, new_pulse_per_rotation,
++ old_pulses & (~new_pulse_per_rotation));
++ mutex_unlock(&tc->update_lock);
++
++ /* invalidate RPM data to force re-read from hardware */
++ tc->valid = false;
++
++ return err;
++}
++
++static int get_fan_speed(struct tc654 *tc)
++{
++ enum TC654_FAN_MODE mode;
++ size_t i;
++
++ mode = get_fan_mode(tc);
++ for (i = 0; i < ARRAY_SIZE(pwm_table); i++) {
++ if (mode == pwm_table[i].mode)
++ return pwm_table[i].min;
++ }
++
++ return -EINVAL;
++}
++
++static int set_fan_speed(struct tc654 *tc, int new_value)
++{
++ int result;
++ size_t i;
++
++ if (new_value > pwm_table[ARRAY_SIZE(pwm_table) - 1].min ||
++ new_value < pwm_table[0].min)
++ return -EINVAL;
++
++ for (i = 0; i < ARRAY_SIZE(pwm_table); i++) {
++ /* exact match */
++ if (pwm_table[i].min == new_value)
++ break;
++
++ /* a little bit too big - go with the previous entry */
++ if (pwm_table[i].min > new_value) {
++ --i;
++ break;
++ }
++ }
++
++ mutex_lock(&tc->update_lock);
++ result = write_fan_mode(tc, pwm_table[i].mode);
++ mutex_unlock(&tc->update_lock);
++ if (result < 0)
++ return result;
++
++ return 0;
++}
++
++/* sysfs */
++
++static ssize_t
++show_fan_input(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = tc654_update_device(dev);
++ int nr = to_sensor_dev_attr(da)->index;
++
++ return sprintf(buf, "%d\n", tc->fan_input[nr]);
++}
++
++static ssize_t
++show_fan_min(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++ int nr = to_sensor_dev_attr(da)->index;
++
++ return sprintf(buf, "%d\n", read_fan_fault_thresh(tc, nr));
++}
++
++static ssize_t
++show_fan_min_alarm(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = tc654_update_device(dev);
++ int nr = to_sensor_dev_attr(da)->index;
++
++ return sprintf(buf, "%d\n", nr == TC654_FAN1 ?
++ tc->alarms[TC654_ALARM_FAN1_FAULT] :
++ tc->alarms[TC654_ALARM_FAN2_FAULT]);
++}
++
++static ssize_t
++show_fan_max_alarm(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = tc654_update_device(dev);
++ int nr = to_sensor_dev_attr(da)->index;
++
++ return sprintf(buf, "%d\n", nr == TC654_FAN1 ?
++ tc->alarms[TC654_ALARM_FAN1_COUNTER_OVERFLOW] :
++ tc->alarms[TC654_ALARM_FAN2_COUNTER_OVERFLOW]);
++}
++
++static ssize_t
++set_fan_min(struct device *dev, struct device_attribute *da,
++ const char *buf, size_t count)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++ long new_min;
++ int nr = to_sensor_dev_attr(da)->index;
++ int old_min = read_fan_fault_thresh(tc, nr);
++ int status = kstrtol(buf, 10, &new_min);
++
++ if (status < 0)
++ return status;
++
++ new_min = (new_min / 50) * 50;
++ if (new_min == old_min) /* No change */
++ return count;
++
++ if (new_min < 0 || new_min > 12750)
++ return -EINVAL;
++
++ mutex_lock(&tc->update_lock);
++ status = write_fan_fault_thresh(tc, nr, new_min);
++ mutex_unlock(&tc->update_lock);
++ return count;
++}
++
++static ssize_t
++show_fan_max(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++ int max_rpm = tc->cached_regs[TC654_REG_CONFIG] & TC654_CTRL_RES ?
++ (((1 << 9) - 1) * 25) /* ((2**9) - 1) * 25 RPM */:
++ (((1 << 8) - 1) * 50) /* ((2**8) - 1) * 50 RPM */;
++
++ return sprintf(buf, "%d\n", max_rpm);
++}
++
++static ssize_t
++show_fan_fault(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = tc654_update_device(dev);
++ int nr = to_sensor_dev_attr(da)->index;
++ u8 fan_fault_mask = nr == TC654_FAN1 ?
++ TC654_STATUS_F1F : TC654_STATUS_F2F;
++
++ return sprintf(buf, "%d\n",
++ !!(tc->cached_regs[TC654_REG_STATUS] & fan_fault_mask));
++}
++
++static ssize_t
++show_fan_pulses(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++ int nr = to_sensor_dev_attr(da)->index;
++
++ return sprintf(buf, "%d\n", get_fan_pulse(tc, nr));
++}
++
++static ssize_t
++set_fan_pulses(struct device *dev, struct device_attribute *da,
++ const char *buf, size_t count)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++ long new_pulse;
++ int nr = to_sensor_dev_attr(da)->index;
++ int status = kstrtol(buf, 10, &new_pulse);
++
++ if (status < 0)
++ return status;
++
++ status = set_fan_pulse(tc, nr, new_pulse);
++ if (status < 0)
++ return status;
++
++ return count;
++}
++
++static ssize_t
++show_pwm_enable(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = tc654_update_device(dev);
++ int pwm_enabled;
++
++ if ((tc->cached_regs[TC654_REG_CONFIG] & TC654_CTRL_SDM) &&
++ !tc->pwm_manual) {
++ pwm_enabled = 0; /* full off */
++ } else {
++ if (tc->valid && tc->vin_status == 0)
++ pwm_enabled = 2; /* automatic fan speed control */
++
++ pwm_enabled = 1; /* PWM Mode */
++ }
++
++ return sprintf(buf, "%d\n", pwm_enabled);
++}
++
++static ssize_t
++set_pwm_enable(struct device *dev, struct device_attribute *da,
++ const char *buf, size_t count)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++ long new_value;
++
++ int result = kstrtol(buf, 10, &new_value);
++
++ if (result < 0)
++ return result;
++
++ mutex_lock(&tc->update_lock);
++ switch (new_value) {
++ case 0: /* no fan control (i.e. is OFF) */
++ result = write_fan_mode(tc, TC654_PWM_OFF);
++ tc->pwm_manual = false;
++ break;
++
++ case 1: /* manual fan control enabled (using pwm) */
++ result = write_fan_mode(tc, TC654_PWM_10000);
++ break;
++
++ case 2: /* automatic fan speed control enabled */
++ result = write_fan_mode(tc, TC654_PWM_VIN);
++ break;
++
++ default:
++ result = -EINVAL;
++ }
++
++ mutex_unlock(&tc->update_lock);
++ return result < 0 ? result : count;
++}
++
++static ssize_t
++show_pwm(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = tc654_update_device(dev);
++ int ret;
++
++ ret = get_fan_speed(tc);
++ if (ret < 0)
++ return ret;
++
++ return sprintf(buf, "%d\n", ret);
++}
++
++static ssize_t
++set_pwm(struct device *dev, struct device_attribute *da,
++ const char *buf, size_t count)
++{
++ struct tc654 *tc = dev_get_drvdata(dev);
++ long new_value = -1;
++ int result = kstrtol(buf, 10, &new_value);
++
++ if (result < 0)
++ return result;
++
++ if (new_value < 0 || new_value > INT_MAX)
++ return -EINVAL;
++
++ if (!tc->pwm_manual)
++ return -EINVAL;
++
++ result = set_fan_speed(tc, new_value);
++ if (result < 0)
++ return result;
++
++ return count;
++}
++
++static ssize_t
++show_temp_alarm_otf(struct device *dev, struct device_attribute *da, char *buf)
++{
++ struct tc654 *tc = tc654_update_device(dev);
++
++ return sprintf(buf, "%d\n", tc->alarms[TC654_ALARM_OVER_TEMPERATURE]);
++}
++
++static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan_input,
++ NULL, TC654_FAN1);
++static SENSOR_DEVICE_ATTR(fan1_min, S_IRUGO | S_IWUSR, show_fan_min,
++ set_fan_min, TC654_FAN1);
++static SENSOR_DEVICE_ATTR(fan1_min_alarm, S_IRUGO, show_fan_min_alarm,
++ NULL, TC654_FAN1);
++static SENSOR_DEVICE_ATTR(fan1_max_alarm, S_IRUGO, show_fan_max_alarm,
++ NULL, TC654_FAN1);
++static SENSOR_DEVICE_ATTR(fan1_max, S_IRUGO, show_fan_max, NULL, TC654_FAN1);
++static SENSOR_DEVICE_ATTR(fan1_fault, S_IRUGO, show_fan_fault,
++ NULL, TC654_FAN1);
++static SENSOR_DEVICE_ATTR(fan1_pulses, S_IRUGO | S_IWUSR, show_fan_pulses,
++ set_fan_pulses, TC654_FAN1);
++static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan_input,
++ NULL, TC654_FAN2);
++static SENSOR_DEVICE_ATTR(fan2_min, S_IRUGO | S_IWUSR, show_fan_min,
++ set_fan_min, TC654_FAN2);
++static SENSOR_DEVICE_ATTR(fan2_max, S_IRUGO, show_fan_max,
++ NULL, TC654_FAN2);
++static SENSOR_DEVICE_ATTR(fan2_min_alarm, S_IRUGO, show_fan_min_alarm,
++ NULL, TC654_FAN2);
++static SENSOR_DEVICE_ATTR(fan2_max_alarm, S_IRUGO, show_fan_max_alarm,
++ NULL, TC654_FAN2);
++static SENSOR_DEVICE_ATTR(fan2_fault, S_IRUGO, show_fan_fault,
++ NULL, TC654_FAN2);
++static SENSOR_DEVICE_ATTR(fan2_pulses, S_IRUGO | S_IWUSR, show_fan_pulses,
++ set_fan_pulses, TC654_FAN2);
++
++static DEVICE_ATTR(pwm1_enable, S_IRUGO | S_IWUSR, show_pwm_enable,
++ set_pwm_enable);
++static DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, show_pwm, set_pwm);
++
++static DEVICE_ATTR(temp1_emergency_alarm, S_IRUGO, show_temp_alarm_otf, NULL);
++
++/* sensors present on all models */
++static struct attribute *tc654_attrs[] = {
++ &sensor_dev_attr_fan1_input.dev_attr.attr,
++ &sensor_dev_attr_fan1_min.dev_attr.attr,
++ &sensor_dev_attr_fan1_max.dev_attr.attr,
++ &sensor_dev_attr_fan1_min_alarm.dev_attr.attr,
++ &sensor_dev_attr_fan1_max_alarm.dev_attr.attr,
++ &sensor_dev_attr_fan1_fault.dev_attr.attr,
++ &sensor_dev_attr_fan1_pulses.dev_attr.attr,
++ &sensor_dev_attr_fan2_input.dev_attr.attr,
++ &sensor_dev_attr_fan2_min.dev_attr.attr,
++ &sensor_dev_attr_fan2_max.dev_attr.attr,
++ &sensor_dev_attr_fan2_min_alarm.dev_attr.attr,
++ &sensor_dev_attr_fan2_max_alarm.dev_attr.attr,
++ &sensor_dev_attr_fan2_fault.dev_attr.attr,
++ &sensor_dev_attr_fan2_pulses.dev_attr.attr,
++
++ &dev_attr_pwm1_enable.attr,
++ &dev_attr_pwm1.attr,
++
++ &dev_attr_temp1_emergency_alarm.attr,
++ NULL
++};
++
++ATTRIBUTE_GROUPS(tc654);
++
++/* cooling device */
++
++static int tc654_get_max_state(struct thermal_cooling_device *cdev,
++ unsigned long *state)
++{
++ *state = 255;
++ return 0;
++}
++
++static int tc654_get_cur_state(struct thermal_cooling_device *cdev,
++ unsigned long *state)
++{
++ struct tc654 *tc = cdev->devdata;
++ int ret;
++
++ if (!tc)
++ return -EINVAL;
++
++ ret = get_fan_speed(tc);
++ if (ret < 0)
++ return ret;
++
++ *state = ret;
++ return 0;
++}
++
++static int tc654_set_cur_state(struct thermal_cooling_device *cdev,
++ unsigned long state)
++{
++ struct tc654 *tc = cdev->devdata;
++
++ if (!tc)
++ return -EINVAL;
++
++ if (state > INT_MAX)
++ return -EINVAL;
++
++ return set_fan_speed(tc, state);
++}
++
++static const struct thermal_cooling_device_ops tc654_fan_cool_ops = {
++ .get_max_state = tc654_get_max_state,
++ .get_cur_state = tc654_get_cur_state,
++ .set_cur_state = tc654_set_cur_state,
++};
++
++
++/* hardware probe and detection */
++
++static int
++tc654_probe(struct i2c_client *client, const struct i2c_device_id *id)
++{
++ struct tc654 *tc;
++ struct device *hwmon_dev;
++ int ret, i;
++
++ if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
++ return -EIO;
++
++ tc = devm_kzalloc(&client->dev, sizeof(*tc), GFP_KERNEL);
++ if (!tc)
++ return -ENOMEM;
++
++ i2c_set_clientdata(client, tc);
++ tc->client = client;
++ mutex_init(&tc->update_lock);
++
++ /* cache all 8 registers */
++ for (i = 0; i < __TC654_REG_NUM; i++) {
++ ret = read_tc(tc, i);
++ if (ret < 0)
++ return ret;
++ }
++
++ /* sysfs hooks */
++ hwmon_dev = devm_hwmon_device_register_with_groups(&client->dev,
++ client->name, tc,
++ tc654_groups);
++ if (IS_ERR(hwmon_dev))
++ return PTR_ERR(hwmon_dev);
++
++#if IS_ENABLED(CONFIG_OF)
++ /* Optional cooling device register for Device tree platforms */
++ tc->cdev = thermal_of_cooling_device_register(client->dev.of_node,
++ "tc654", tc,
++ &tc654_fan_cool_ops);
++#else /* CONFIG_OF */
++ /* Optional cooling device register for non Device tree platforms */
++ tc->cdev = thermal_cooling_device_register("tc654", tc,
++ &tc654_fan_cool_ops);
++#endif /* CONFIG_OF */
++
++ dev_info(&client->dev, "%s: sensor '%s'\n",
++ dev_name(hwmon_dev), client->name);
++
++ return 0;
++}
++
++static const struct i2c_device_id tc654_ids[] = {
++ { "tc654", 0, },
++ { }
++};
++MODULE_DEVICE_TABLE(i2c, tc654_ids);
++
++/* Return 0 if detection is successful, -ENODEV otherwise */
++static int
++tc654_detect(struct i2c_client *new_client, struct i2c_board_info *info)
++{
++ struct i2c_adapter *adapter = new_client->adapter;
++ int manufacturer, product;
++
++ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
++ return -ENODEV;
++
++ manufacturer = i2c_smbus_read_byte_data(new_client, TC654_REG_MFR_ID);
++ if (manufacturer != TC654_MFR_ID_MICROCHIP)
++ return -ENODEV;
++
++ product = i2c_smbus_read_byte_data(new_client, TC654_REG_VER_ID);
++ if (!((product == TC654_VER_ID) || (product == TC655_VER_ID)))
++ return -ENODEV;
++
++ strlcpy(info->type, "tc654", I2C_NAME_SIZE);
++ return 0;
++}
++
++static struct i2c_driver tc654_driver = {
++ .class = I2C_CLASS_HWMON,
++ .driver = {
++ .name = "tc654",
++ },
++ .probe = tc654_probe,
++ .id_table = tc654_ids,
++ .detect = tc654_detect,
++ .address_list = normal_i2c,
++};
++
++module_i2c_driver(tc654_driver);
++
++MODULE_AUTHOR("Christian Lamparter <chunkeey@gmail.com>");
++MODULE_DESCRIPTION("Microchip TC654/TC655 hwmon driver");
++MODULE_LICENSE("GPL");