diff options
| author | Sven Hauer <sven.hauer+github@uniku.de> | 2022-06-27 22:25:12 +0200 |
|---|---|---|
| committer | Sander Vanheule <sander@svanheule.net> | 2022-06-28 10:58:16 +0200 |
| commit | 7e21ce8e2b0b73f145af96958511f761544942d7 (patch) | |
| tree | 8321c80257cc422b94afca4c7470dafcba1046ae /target | |
| parent | d2d5aabdbb947443b0d5f75c3847754c7c38a117 (diff) | |
| download | upstream-7e21ce8e2b0b73f145af96958511f761544942d7.tar.gz upstream-7e21ce8e2b0b73f145af96958511f761544942d7.tar.bz2 upstream-7e21ce8e2b0b73f145af96958511f761544942d7.zip | |
ath79: support for TP-Link EAP225 v4
This model is almost identical to the EAP225 v3.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>
Diffstat (limited to 'target')
| -rw-r--r-- | target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts | 59 | ||||
| -rw-r--r-- | target/linux/ath79/generic/base-files/etc/board.d/02_network | 1 | ||||
| -rw-r--r-- | target/linux/ath79/image/generic-tp-link.mk | 11 |
3 files changed, 71 insertions, 0 deletions
diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts new file mode 100644 index 0000000000..ae27ff7068 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts @@ -0,0 +1,59 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_tplink_eap2x5-1port.dtsi" + +/ { + compatible = "tplink,eap225-v4", "qca,qca9563"; + model = "TP-Link EAP225 v4"; + + aliases { + led-boot = &led_status_green; + led-failsafe = &led_status_amber; + led-running = &led_status_green; + led-upgrade = &led_status_amber; + }; + + leds { + compatible = "gpio-leds"; + + led_status_green: status_green { + label = "green:status"; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_status_amber: status_amber { + label = "amber:status"; + gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&art { + precalibration_ath10k: pre-calibration@5000 { + reg = <0x5000 0x2f20>; + }; +}; + +ð0 { + phy-handle = <&phy6>; + phy-mode = "sgmii"; +}; + +&mdio0 { + phy6: ethernet-phy@6 { + reg = <6>; + }; +}; + +&pcie { + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0 0 0 0 0>; + + mac-address-increment = <1>; + + nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>; + nvmem-cell-names = "mac-address", "pre-calibration"; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 42ab19b47a..7ba39c4c49 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -79,6 +79,7 @@ ath79_setup_interfaces() tplink,eap225-outdoor-v3|\ tplink,eap225-v1|\ tplink,eap225-v3|\ + tplink,eap225-v4|\ tplink,eap245-v1|\ tplink,re350k-v1|\ tplink,re355-v1|\ diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index ffe999660a..6d9ba2cd40 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -434,6 +434,17 @@ define Device/tplink_eap225-v3 endef TARGET_DEVICES += tplink_eap225-v3 +define Device/tplink_eap225-v4 + $(Device/tplink-eap2x5) + SOC := qca9563 + IMAGE_SIZE := 13824k + DEVICE_MODEL := EAP225 + DEVICE_VARIANT := v4 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + TPLINK_BOARD_ID := EAP225-V3 +endef +TARGET_DEVICES += tplink_eap225-v4 + define Device/tplink_eap225-wall-v2 $(Device/tplink-eap2x5) SOC := qca9561 |