ar71xx: add support for TP-Link TL-WR942N v1

TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

14 files changed, 333 insertions, 2 deletions

diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index 2f9ae8b10e..be6dfcc968 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -745,6 +745,16 @@ tl-wr840n-v3)
 	ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E"
 	ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
 	;;
+tl-wr942n-v1)
+	ucidef_set_led_switch "lan1" "LAN1" "$board:green:lan1" "switch0" "0x04"
+	ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08"
+	ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x10"
+	ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02"
+	ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0"
+	ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
+	ucidef_set_led_usbdev "usb1" "USB1" "$board:green:usb1" "1-1.2"
+	ucidef_set_led_usbdev "usb2" "USB2" "$board:green:usb2" "1-1.1"
+	;;
 tl-wr1043nd|\
 tl-wr1043nd-v2)
 	ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index 0dc8bf31a8..b805487977 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -411,7 +411,8 @@ ar71xx_setup_interfaces()
 	tl-mr3420-v2|\
 	tl-wr841n-v8|\
 	tl-wr842n-v2|\
-	tl-wr941nd-v5)
+	tl-wr941nd-v5|\
+	tl-wr942n-v1)
 		ucidef_set_interfaces_lan_wan "eth1.1" "eth0"
 		ucidef_add_switch "switch0" \
 			"0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index ae43351c6a..369abde9d4 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -36,6 +36,7 @@ get_status_led() {
 	db120|\
 	dr344|\
 	tew-632brp|\
+	tl-wr942n-v1|\
 	wpj344|\
 	zbt-we1526)
 		status_led="$board:green:status"
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index e781c6ee7e..5660d3eaa9 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -1166,6 +1166,9 @@ ar71xx_board_detect() {
 	*"TL-WR941ND")
 		name="tl-wr941nd"
 		;;
+	*"TL-WR942N v1")
+		name="tl-wr942n-v1"
+		;;
 	*"Tube2H")
 		name="tube2h"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 16701f64ca..e14f8f3e49 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -271,6 +271,7 @@ platform_check_image() {
 	tew-712br|\
 	tew-732br|\
 	tew-823dru|\
+	tl-wr942n-v1|\
 	unifi-outdoor|\
 	unifiac-lite|\
 	unifiac-pro|\
diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
index 43a487d20e..df1108d904 100644
--- a/target/linux/ar71xx/config-4.4
+++ b/target/linux/ar71xx/config-4.4
@@ -209,6 +209,7 @@ CONFIG_ATH79_MACH_TL_WR841N_V9=y
 CONFIG_ATH79_MACH_TL_WR941ND=y
 CONFIG_ATH79_MACH_TL_WR941ND_V6=y
 CONFIG_ATH79_MACH_TL_WR940N_V4=y
+CONFIG_ATH79_MACH_TL_WR942N_V1=y
 CONFIG_ATH79_MACH_TUBE2H=y
 CONFIG_ATH79_MACH_UBNT=y
 CONFIG_ATH79_MACH_UBNT_UNIFIAC=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index c18eec557d..ae64c6e92e 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -1695,6 +1695,17 @@ config ATH79_MACH_TL_WR940N_V4
 	select ATH79_DEV_M25P80
 	select ATH79_DEV_WMAC
 
+config ATH79_MACH_TL_WR942N_V1
+	bool "TP-LINK TL-WR942N v1 support"
+	select SOC_QCA956X
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+	select ATH79_NVRAM
+
 config ATH79_MACH_TL_WR1041N_V2
 	bool "TP-LINK TL-WR1041N v2 support"
 	select SOC_AR934X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 55c5a2a939..bf5515b4f3 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -214,6 +214,7 @@ obj-$(CONFIG_ATH79_MACH_TL_WR841N_V9)		+= mach-tl-wr841n-v9.o
 obj-$(CONFIG_ATH79_MACH_TL_WR941ND)		+= mach-tl-wr941nd.o
 obj-$(CONFIG_ATH79_MACH_TL_WR941ND_V6)		+= mach-tl-wr941nd-v6.o
 obj-$(CONFIG_ATH79_MACH_TL_WR940N_V4)		+= mach-tl-wr940n-v4.o
+obj-$(CONFIG_ATH79_MACH_TL_WR942N_V1)		+= mach-tl-wr942n-v1.o
 obj-$(CONFIG_ATH79_MACH_TUBE2H)			+= mach-tube2h.o
 obj-$(CONFIG_ATH79_MACH_UBNT)			+= mach-ubnt.o
 obj-$(CONFIG_ATH79_MACH_UBNT_UNIFIAC)		+= mach-ubnt-unifiac.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c
new file mode 100644
index 0000000000..72910400c5
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c
@@ -0,0 +1,279 @@
+/*
+ *  TP-Link TL-WR942N(RU) v1 board support
+ *
+ *  Copyright (C) 2017 Sergey Studzinski <serguzhg@gmail.com>
+ *  Thanks to Henryk Heisig <hyniu@o2.pl>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/spi/spi_gpio.h>
+#include <linux/spi/74x164.h>
+
+#include "common.h"
+#include "dev-m25p80.h"
+#include "machtypes.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-spi.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "nvram.h"
+
+#define TL_WR942N_V1_KEYS_POLL_INTERVAL		20
+#define TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL	\
+					(3 * TL_WR942N_V1_KEYS_POLL_INTERVAL)
+
+#define TL_WR942N_V1_GPIO_BTN_RESET		1
+#define TL_WR942N_V1_GPIO_BTN_RFKILL		2
+
+#define TL_WR942N_V1_GPIO_UART_TX		4
+#define TL_WR942N_V1_GPIO_UART_RX		5
+
+#define TL_WR942N_V1_GPIO_LED_USB2		14
+#define TL_WR942N_V1_GPIO_LED_USB1		15
+
+#define TL_WR942N_V1_GPIO_SHIFT_OE		16
+#define TL_WR942N_V1_GPIO_SHIFT_SER		17
+#define TL_WR942N_V1_GPIO_SHIFT_SRCLK		18
+#define TL_WR942N_V1_GPIO_SHIFT_SRCLR		19
+#define TL_WR942N_V1_GPIO_SHIFT_RCLK		20
+#define TL_WR942N_V1_GPIO_LED_WPS		21
+#define TL_WR942N_V1_GPIO_LED_STATUS		22
+
+#define TL_WR942N_V1_74HC_GPIO_BASE		QCA956X_GPIO_COUNT
+#define TL_WR942N_V1_74HC_GPIO_LED_LAN4		23
+#define TL_WR942N_V1_74HC_GPIO_LED_LAN3		24
+#define TL_WR942N_V1_74HC_GPIO_LED_LAN2		25
+#define TL_WR942N_V1_74HC_GPIO_LED_LAN1		26
+#define TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN	27
+#define TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER	28
+#define TL_WR942N_V1_74HC_GPIO_LED_WLAN		29
+#define TL_WR942N_V1_74HC_GPIO_HUB_RESET	30 /* from u-boot sources */
+
+#define TL_WR942N_V1_SSR_BIT_0			0
+#define TL_WR942N_V1_SSR_BIT_1			1
+#define TL_WR942N_V1_SSR_BIT_2			2
+#define TL_WR942N_V1_SSR_BIT_3			3
+#define TL_WR942N_V1_SSR_BIT_4			4
+#define TL_WR942N_V1_SSR_BIT_5			5
+#define TL_WR942N_V1_SSR_BIT_6			6
+#define TL_WR942N_V1_SSR_BIT_7			7
+
+#define TL_WR942N_V1_WMAC_CALDATA_OFFSET	0x1000
+#define TL_WR942N_V1_DEFAULT_MAC_ADDR		0x1fe40008
+#define TL_WR942N_V1_DEFAULT_MAC_SIZE		0x200
+
+#define GPIO_IN_ENABLE0_UART_SIN_LSB		8
+#define GPIO_IN_ENABLE0_UART_SIN_MASK		0x0000ff00
+
+static struct gpio_led tl_wr942n_v1_leds_gpio[] __initdata = {
+	{
+		.name		= "tl-wr942n-v1:green:status",
+		.gpio		= TL_WR942N_V1_GPIO_LED_STATUS,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:wlan",
+		.gpio		= TL_WR942N_V1_74HC_GPIO_LED_WLAN,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:lan1",
+		.gpio		= TL_WR942N_V1_74HC_GPIO_LED_LAN1,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:lan2",
+		.gpio		= TL_WR942N_V1_74HC_GPIO_LED_LAN2,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:lan3",
+		.gpio		= TL_WR942N_V1_74HC_GPIO_LED_LAN3,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:lan4",
+		.gpio		= TL_WR942N_V1_74HC_GPIO_LED_LAN4,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:wan",
+		.gpio		= TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:amber:wan",
+		.gpio		= TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:wps",
+		.gpio		= TL_WR942N_V1_GPIO_LED_WPS,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:usb1",
+		.gpio		= TL_WR942N_V1_GPIO_LED_USB1,
+		.active_low	= 1,
+	}, {
+		.name		= "tl-wr942n-v1:green:usb2",
+		.gpio		= TL_WR942N_V1_GPIO_LED_USB2,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button tl_wr942n_v1_gpio_keys[] __initdata = {
+	{
+		.desc			= "Reset button",
+		.type			= EV_KEY,
+		.code			= KEY_RESTART,
+		.debounce_interval	= TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= TL_WR942N_V1_GPIO_BTN_RESET,
+		.active_low		= 1,
+	}, {
+		.desc			= "RFKILL button",
+		.type			= EV_KEY,
+		.code			= KEY_RFKILL,
+		.debounce_interval	= TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= TL_WR942N_V1_GPIO_BTN_RFKILL,
+		.active_low		= 1,
+	},
+};
+
+static struct spi_gpio_platform_data tl_wr942n_v1_spi_data = {
+	.sck		= TL_WR942N_V1_GPIO_SHIFT_SRCLK,
+	.miso		= SPI_GPIO_NO_MISO,
+	.mosi		= TL_WR942N_V1_GPIO_SHIFT_SER,
+	.num_chipselect	= 1,
+};
+
+static u8 tl_wr942n_v1_ssr_initdata[] __initdata = {
+	BIT(TL_WR942N_V1_SSR_BIT_7) |
+	BIT(TL_WR942N_V1_SSR_BIT_6) |
+	BIT(TL_WR942N_V1_SSR_BIT_5) |
+	BIT(TL_WR942N_V1_SSR_BIT_4) |
+	BIT(TL_WR942N_V1_SSR_BIT_3) |
+	BIT(TL_WR942N_V1_SSR_BIT_2) |
+	BIT(TL_WR942N_V1_SSR_BIT_1) |
+	BIT(TL_WR942N_V1_SSR_BIT_0)
+};
+
+static struct gen_74x164_chip_platform_data tl_wr942n_v1_ssr_data = {
+	.base		= TL_WR942N_V1_74HC_GPIO_BASE,
+	.num_registers	= ARRAY_SIZE(tl_wr942n_v1_ssr_initdata),
+	.init_data	= tl_wr942n_v1_ssr_initdata,
+};
+
+static struct platform_device tl_wr942n_v1_spi_device = {
+	.name		= "spi_gpio",
+	.id		= 1,
+	.dev = {
+		.platform_data = &tl_wr942n_v1_spi_data,
+	},
+};
+
+static struct spi_board_info tl_wr942n_v1_spi_info[] = {
+	{
+		.bus_num		= 1,
+		.chip_select		= 0,
+		.max_speed_hz		= 10000000,
+		.modalias		= "74x164",
+		.platform_data		= &tl_wr942n_v1_ssr_data,
+		.controller_data	= (void *) TL_WR942N_V1_GPIO_SHIFT_RCLK,
+	},
+};
+
+static void tl_wr942n_v1_get_mac(const char *name, char *mac)
+{
+	u8 *nvram = (u8 *) KSEG1ADDR(TL_WR942N_V1_DEFAULT_MAC_ADDR);
+	int err;
+
+	err = ath79_nvram_parse_mac_addr(nvram, TL_WR942N_V1_DEFAULT_MAC_SIZE,
+					 name, mac);
+
+	if (err)
+		pr_err("no MAC address found for %s\n", name);
+}
+
+static void __init tl_wr942n_v1_setup(void)
+{
+	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+	u8 tmpmac[ETH_ALEN];
+	void __iomem *base;
+	u32 t;
+
+	ath79_register_m25p80(NULL);
+
+	spi_register_board_info(tl_wr942n_v1_spi_info,
+				ARRAY_SIZE(tl_wr942n_v1_spi_info));
+	platform_device_register(&tl_wr942n_v1_spi_device);
+
+	/* Check inherited UART RX GPIO definition */
+	base = ioremap(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE);
+
+	t = __raw_readl(base + QCA956X_GPIO_REG_IN_ENABLE0);
+	if (((t & GPIO_IN_ENABLE0_UART_SIN_MASK)
+	     >> GPIO_IN_ENABLE0_UART_SIN_LSB) == TL_WR942N_V1_GPIO_LED_USB1) {
+		pr_warn("Active UART detected on USBLED's GPIOs!\n");
+
+		tl_wr942n_v1_leds_gpio[9].gpio = TL_WR942N_V1_GPIO_UART_TX;
+		tl_wr942n_v1_leds_gpio[10].gpio = TL_WR942N_V1_GPIO_UART_RX;
+	}
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(tl_wr942n_v1_leds_gpio),
+				 tl_wr942n_v1_leds_gpio);
+
+	ath79_register_gpio_keys_polled(-1, TL_WR942N_V1_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(tl_wr942n_v1_gpio_keys),
+					tl_wr942n_v1_gpio_keys);
+
+	tl_wr942n_v1_get_mac("MAC:", tmpmac);
+
+	/* swap PHYs */
+	ath79_setup_qca956x_eth_cfg(QCA956X_ETH_CFG_SW_PHY_SWAP |
+				    QCA956X_ETH_CFG_SW_PHY_ADDR_SWAP);
+
+	ath79_register_mdio(0, 0x0);
+	ath79_register_mdio(1, 0x0);
+
+	/* WAN port */
+	ath79_init_mac(ath79_eth0_data.mac_addr, tmpmac, 1);
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+	ath79_eth0_data.speed = SPEED_100;
+	ath79_eth0_data.duplex = DUPLEX_FULL;
+
+	/* swaped PHYs */
+	ath79_eth0_data.phy_mask = BIT(0);
+	ath79_register_eth(0);
+
+	/* LAN ports */
+	ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+	ath79_init_mac(ath79_eth1_data.mac_addr, tmpmac, 0);
+	ath79_eth1_data.speed = SPEED_1000;
+	ath79_eth1_data.duplex = DUPLEX_FULL;
+
+	/* swaped PHYs */
+	ath79_switch_data.phy_poll_mask |= BIT(0);
+	ath79_switch_data.phy4_mii_en = 1;
+	ath79_register_eth(1);
+
+	ath79_register_wmac(art + TL_WR942N_V1_WMAC_CALDATA_OFFSET, tmpmac);
+
+	ath79_register_usb();
+
+	gpio_request_one(TL_WR942N_V1_74HC_GPIO_HUB_RESET,
+			 GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
+			 "USB power");
+
+	gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_OE,
+			 GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
+			 "LED control");
+
+	gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_SRCLR,
+			 GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
+			 "LED reset");
+}
+
+MIPS_MACHINE(ATH79_MACH_TL_WR942N_V1, "TL-WR942N-V1", "TP-LINK TL-WR942N v1",
+	     tl_wr942n_v1_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 0d05086a1c..46d250d47d 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -262,6 +262,7 @@ enum ath79_mach_type {
 	ATH79_MACH_TL_WR941ND_V5,		/* TP-LINK TL-WR941ND v5 */
 	ATH79_MACH_TL_WR941ND_V6,		/* TP-LINK TL-WR941ND v6 */
 	ATH79_MACH_TL_WR940N_V4,		/* TP-LINK TL-WR940N v4 */
+	ATH79_MACH_TL_WR942N_V1,		/* TP-LINK TL-WR942N v1 */
 	ATH79_MACH_TUBE2H,			/* Alfa Network Tube2H */
 	ATH79_MACH_UBNT_AIRGW,			/* Ubiquiti AirGateway */
 	ATH79_MACH_UBNT_AIRGWP,			/* Ubiquiti AirGateway Pro */
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/nvram.c b/target/linux/ar71xx/files/arch/mips/ath79/nvram.c
index e55af5abe2..a1de55fb19 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/nvram.c
+++ b/target/linux/ar71xx/files/arch/mips/ath79/nvram.c
@@ -13,6 +13,7 @@
 #include <linux/errno.h>
 #include <linux/init.h>
 #include <linux/string.h>
+#include <linux/etherdevice.h>
 
 #include "nvram.h"
 
@@ -67,7 +68,11 @@ int ath79_nvram_parse_mac_addr(const char *nvram, unsigned nvram_len,
 	t = sscanf(mac_str, "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx",
 		   &mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]);
 
-	if (t != 6) {
+	if (t != ETH_ALEN)
+		t = sscanf(mac_str, "%02hhx-%02hhx-%02hhx-%02hhx-%02hhx-%02hhx",
+			&mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]);
+
+	if (t != ETH_ALEN) {
 		ret = -EINVAL;
 		goto free;
 	}
diff --git a/target/linux/ar71xx/image/tp-link.mk b/target/linux/ar71xx/image/tp-link.mk
index 5ac641bf36..d9c7982e8c 100644
--- a/target/linux/ar71xx/image/tp-link.mk
+++ b/target/linux/ar71xx/image/tp-link.mk
@@ -873,6 +873,21 @@ define Device/tl-wr941nd-v6-cn
 endef
 TARGET_DEVICES += tl-wr941nd-v2 tl-wr941nd-v3 tl-wr941nd-v4 tl-wr941nd-v5 tl-wr941nd-v6 tl-wr941nd-v6-cn tl-wr940n-v4
 
+define Device/tl-wr942n-v1
+  DEVICE_TITLE := TP-LINK TL-WR942N v1
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+  BOARDNAME := TL-WR942N-V1
+  TPLINK_BOARD_NAME := TLWR942NV1
+  DEVICE_PROFILE := TLWR942
+  IMAGE_SIZE := 14464k
+  KERNEL := kernel-bin | patch-cmdline | lzma | uImageArcher lzma
+  IMAGES := sysupgrade.bin factory.bin
+  IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade
+  IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
+  MTDPARTS := spi0.0:128k(u-boot)ro,1344k(kernel),13120k(rootfs),64k(product-info)ro,64k(partition-table)ro,256k(oem-config)ro,1344k(oem-vars)ro,64k(ART)ro,14464k@0x20000(firmware)
+endef
+TARGET_DEVICES += tl-wr942n-v1
+
 define Device/tl-wr1041n-v2
   $(Device/tplink-4mlzma)
   DEVICE_TITLE := TP-LINK TL-WR1041N v2
diff --git a/target/linux/ar71xx/mikrotik/config-default b/target/linux/ar71xx/mikrotik/config-default
index 5c665801fe..748252ce48 100644
--- a/target/linux/ar71xx/mikrotik/config-default
+++ b/target/linux/ar71xx/mikrotik/config-default
@@ -172,6 +172,7 @@ CONFIG_ATH79_MACH_RBSXTLITE=y
 # CONFIG_ATH79_MACH_TL_WR940N_V4 is not set
 # CONFIG_ATH79_MACH_TL_WR941ND is not set
 # CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set
+# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set
 # CONFIG_ATH79_MACH_TUBE2H is not set
 # CONFIG_ATH79_MACH_UBNT is not set
 # CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set
diff --git a/target/linux/ar71xx/nand/config-default b/target/linux/ar71xx/nand/config-default
index cc2b25c1af..7ae42fe8b9 100644
--- a/target/linux/ar71xx/nand/config-default
+++ b/target/linux/ar71xx/nand/config-default
@@ -160,6 +160,7 @@ CONFIG_ATH79_MACH_RAMBUTAN=y
 # CONFIG_ATH79_MACH_TL_WR940N_V4 is not set
 # CONFIG_ATH79_MACH_TL_WR941ND is not set
 # CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set
+# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set
 # CONFIG_ATH79_MACH_TUBE2H is not set
 # CONFIG_ATH79_MACH_UBNT is not set
 # CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set