aboutsummaryrefslogtreecommitdiffstats
path: root/target
diff options
context:
space:
mode:
authorDaniel Danzberger <daniel@dd-wrt.com>2019-11-01 12:27:13 +0100
committerJohn Crispin <john@phrozen.org>2019-11-02 19:25:15 +0100
commitaffe633be4c8122835e255425418ba1680a652e3 (patch)
tree2eb14002f5e4fd01fbc2549b0752343cc25f9c1e /target
parent2d00cf75159938e5e8c9f26e6cdb5a4843213a3e (diff)
downloadupstream-affe633be4c8122835e255425418ba1680a652e3.tar.gz
upstream-affe633be4c8122835e255425418ba1680a652e3.tar.bz2
upstream-affe633be4c8122835e255425418ba1680a652e3.zip
ipq40xx: ipq4019: Add new device Compex WPJ419
This device contains 2 flash devices. One NOR (32M) and one NAND (128M). U-boot and caldata are on the NOR, the firmware on the NAND. SoC: IPQ4019 CPU: 4x 710MHz ARMv7 RAM: 256MB FLASH: NOR:32MB NAND:128MB ETH: 2x GMAC Gigabit POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V) WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO 1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO USB: 1x 3.0 PCI: 1x Mini PCIe SIM: 1x Slot SD: 1x MicroSD slot BTN: Reset LED: - Power - Ethernet UART: 1x Serial Port 4 Pin Connector (UART) 1x Serial Port 6 Pin Connector (High Speed UART) POWER: 12V 2A Installation ------------ Initial flashing can only be done via u-boot using the following commands: tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi nand erase.chip; nand write ${fileaddr} 0x0 ${filesize} res Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Diffstat (limited to 'target')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata2
-rw-r--r--target/linux/ipq40xx/base-files/lib/upgrade/platform.sh3
-rw-r--r--target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts374
-rw-r--r--target/linux/ipq40xx/image/Makefile14
-rw-r--r--target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch3
6 files changed, 396 insertions, 1 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 25402b7eb4..dafd83234e 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -48,6 +48,7 @@ ipq40xx_setup_interfaces()
ucidef_set_interface_lan "eth0"
;;
avm,fritzrepeater-3000|\
+ compex,wpj419|\
compex,wpj428)
ucidef_set_interface_lan "eth0 eth1"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 2336ef3c7b..d4e4cc49ec 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -70,6 +70,7 @@ case "$FIRMWARE" in
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
+ compex,wpj419 |\
compex,wpj428 |\
engenius,eap1300 |\
openmesh,a42 |\
@@ -133,6 +134,7 @@ case "$FIRMWARE" in
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
+ compex,wpj419 |\
compex,wpj428 |\
engenius,eap1300 |\
openmesh,a42 |\
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 3445f2b50f..96f865c67e 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -73,6 +73,9 @@ platform_do_upgrade() {
CI_KERNPART="linux"
nand_do_upgrade "$1"
;;
+ compex,wpj419)
+ nand_do_upgrade "$1"
+ ;;
linksys,ea6350v3 |\
linksys,ea8300)
platform_do_upgrade_linksys "$1"
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts
new file mode 100644
index 0000000000..b6eb99278b
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts
@@ -0,0 +1,374 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Nguyen Dinh Phi <phi_nguyen@compex.com.sg>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Compex WPJ419";
+ compatible = "compex,wpj419", "qcom,ipq4019";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ reserved-memory {
+ ranges;
+ rsvd1@87000000 {
+ /* Reserved for other subsystem */
+ reg = <0x87000000 0x500000>;
+ no-map;
+ };
+ wifi_dump@87500000 {
+ reg = <0x87500000 0x600000>;
+ no-map;
+ };
+
+ rsvd2@87B00000 {
+ /* Reserved for other subsystem */
+ reg = <0x87B00000 0x500000>;
+ no-map;
+ };
+ };
+
+ chosen {
+ bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused";
+ };
+
+ soc {
+ pinctrl@1000000 {
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ bias-disable;
+ };
+
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ bias-disable;
+ output-high;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio20", "gpio21";
+ function = "blsp_i2c0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ led_0_pins: led0_pinmux {
+ mux_1 {
+ pins = "gpio36";
+ function = "led0";
+ bias-pull-down;
+ };
+ mux_2 {
+ pins = "gpio40";
+ function = "led4";
+ bias-pull-down;
+ };
+ };
+ };
+
+ blsp_dma: dma@7884000 {
+ status = "okay";
+ };
+
+ spi_0: spi@78b5000 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 41 GPIO_ACTIVE_HIGH>;
+ num-cs = <2>;
+
+ flash0@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+ broken-flash-reset;
+
+ partitions {
+ compatible = "fixed-partitions";
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x040000 0x020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "0:QSEE";
+ reg = <0x060000 0x060000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "0:CDT";
+ reg = <0x0c0000 0x010000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x0d0000 0x010000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "u-boot-env";
+ reg = <0x0e0000 0x010000>;
+ };
+
+ partition@f0000 {
+ label = "u-boot";
+ reg = <0x0f0000 0x080000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "0:ART";
+ reg = <0x170000 0x010000>;
+ read-only;
+ };
+ };
+ };
+
+ nand@1 {
+ reg = <1>;
+ status = "okay";
+ compatible = "spi-nand";
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* The device has 128MB, but we can only address
+ * 64MB because of the bootloader's default settings.
+ * This is due to the old mt29f driver,
+ * which detected the deivce with only 64MB
+ */
+ partition@0 {
+ label = "ubi";
+ reg = <0x0000000 0x4000000>;
+ };
+ };
+ };
+ };
+
+ mdio@90000 {
+ status = "okay";
+ phy-reset-gpio = <&tlmm 47 0>;
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ i2c_0: i2c@78b7000 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+ };
+
+ serial@78af000 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ serial@78b0000 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ usb3_ss_phy: ssphy@9a000 {
+ status = "okay";
+ };
+
+ usb3_hs_phy: hsphy@a6000 {
+ status = "okay";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "okay";
+ };
+
+ usb2_hs_phy: hsphy@a8000 {
+ status = "okay";
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ cryptobam: dma@8e04000 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_lan_bmp = <0x1e>;
+ switch_wan_bmp = <0x20>;
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+
+ qpic_bam: dma@7984000 {
+ status = "okay";
+ };
+
+ pcie0: pci@40000000 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+
+ nand: qpic-nand@79b0000 {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+ };
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index ed46bca649..ef80e68393 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -164,6 +164,20 @@ define Device/avm_fritzrepeater-3000
endef
TARGET_DEVICES += avm_fritzrepeater-3000
+define Device/compex_wpj419
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Compex
+ DEVICE_MODEL := WPJ419
+ DEVICE_DTS := qcom-ipq4019-wpj419
+ DEVICE_DTS_CONFIG := config@12
+ KERNEL_INSTALL := 1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ FILESYSTEMS := squashfs
+endef
+TARGET_DEVICES += compex_wpj419
+
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_VENDOR := Compex
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index 2fe6e46966..4649b337e3 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,35 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,36 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -40,6 +40,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
+ qcom-ipq4019-unielec-u4019-32m.dtb \
++ qcom-ipq4019-wpj419.dtb \
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
+ qcom-ipq4029-mr33.dtb \