ipq40xx: add support for ALFA Network AP120C-AC

ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.

Specification:

- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)

Flash instruction:

1. This board uses dual-image feature (128 MB NAND is divided into two
   64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
   than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
   preserving settings.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

10 files changed, 742 insertions, 4 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index 9105bf2452..2fca1cbc9f 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -11,6 +11,9 @@ board=$(board_name)
 boardname="${board##*,}"
 
 case "$board" in
+alfa-network,ap120c-ac)
+	ucidef_set_led_netdev "wan" "WAN" "${boardname}:amber:wan" "eth1"
+	;;
 asus,rt-ac58u)
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2G" "phy0tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:blue:wlan5G" "phy1tpt"
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 43be592071..b28f5ef12c 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -12,7 +12,8 @@ ipq40xx_setup_interfaces()
 	local board="$1"
 
 	case "$board" in
-	8dev,jalapeno)
+	8dev,jalapeno|\
+	alfa-network,ap120c-ac)
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		;;
 	asus,map-ac2200|\
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 21d9063fd4..718224f1e0 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -119,6 +119,7 @@ case "$FIRMWARE" in
 "ath10k/pre-cal-ahb-a000000.wifi.bin")
 	case "$board" in
 	8dev,jalapeno |\
+	alfa-network,ap120c-ac |\
 	glinet,gl-b1300 |\
 	linksys,ea6350v3 |\
 	qcom,ap-dk01.1-c1)
@@ -160,6 +161,7 @@ case "$FIRMWARE" in
 "ath10k/pre-cal-ahb-a800000.wifi.bin")
 	case "$board" in
 	8dev,jalapeno |\
+	alfa-network,ap120c-ac |\
 	glinet,gl-b1300 |\
 	linksys,ea6350v3 |\
 	qcom,ap-dk01.1-c1)
diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount
new file mode 100755
index 0000000000..604f88c396
--- /dev/null
+++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount
@@ -0,0 +1,14 @@
+#!/bin/sh /etc/rc.common
+
+START=99
+
+start() {
+	. /lib/functions.sh
+
+	case $(board_name) in
+	alfa-network,ap120c-ac)
+		[ -n "$(fw_printenv bootcount changed 2>/dev/null)" ] &&\
+			echo -e "bootcount\nchanged\n" | /usr/sbin/fw_setenv -s -
+		;;
+	esac
+}
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index f6bc173a76..b92a2bfe9f 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -46,7 +46,8 @@ zyxel_do_upgrade() {
 
 platform_do_upgrade() {
 	case "$(board_name)" in
-	8dev,jalapeno)
+	8dev,jalapeno |\
+	alfa-network,ap120c-ac)
 		nand_do_upgrade "$ARGV"
 		;;
 	asus,map-ac2200)
@@ -81,6 +82,16 @@ platform_do_upgrade() {
 
 platform_nand_pre_upgrade() {
 	case "$(board_name)" in
+	alfa-network,ap120c-ac)
+		part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
+		if [ "$part" = "rootfs1" ]; then
+			fw_setenv active 2 || exit 1
+			CI_UBIPART="rootfs2"
+		else
+			fw_setenv active 1 || exit 1
+			CI_UBIPART="rootfs1"
+		fi
+		;;
 	asus,rt-ac58u)
 		CI_UBIPART="UBI_DEV"
 		CI_KERNPART="linux"
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
new file mode 100644
index 0000000000..63e3426568
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "ALFA Network AP120C-AC";
+	compatible = "alfa-network,ap120c-ac", "qcom,ipq4019";
+
+	aliases {
+		led-boot = &status;
+		led-failsafe = &status;
+		led-running = &status;
+		led-upgrade = &status;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status: status {
+			label = "ap120c-ac:blue:status";
+			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		wan {
+			label = "ap120c-ac:amber:wan";
+			gpios = <&qca8075 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "ap120c-ac:green:wlan2g";
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "ap120c-ac:red:wlan5g";
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+
+	soc {
+		mdio@90000 {
+			status = "okay";
+
+			pinctrl-0 = <&mdio_pins>;
+			pinctrl-names = "default";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		counter@4a1000 {
+			compatible = "qcom,qca-gcnt";
+			reg = <0x4a1000 0x4>;
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		usb2@60f8800 {
+			status = "okay";
+		};
+
+		usb3@8af8800 {
+			status = "okay";
+
+			dwc3@8a00000 {
+				phys = <&usb3_hs_phy>;
+				phy-names = "usb2-phy";
+			};
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		qca8075: ess-switch@c000000 {
+			status = "okay";
+
+			switch_lan_bmp = <0x10>;
+			switch_wan_bmp = <0x20>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	tpm@29 {
+		compatible = "atmel,at97sc3204t";
+		reg = <0x29>;
+	};
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
+		   <&tlmm  4 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+			};
+
+			partition@f0000 {
+				label = "APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "priv_data1";
+				reg = <0x00180000 0x00010000>;
+				read-only;
+			};
+
+			partition@190000 {
+				label = "priv_data2";
+				reg = <0x00190000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+
+	nand@1 {
+		compatible = "spinand,mt29f";
+		reg = <1>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "rootfs1";
+				reg = <0x00000000 0x04000000>;
+			};
+
+			partition@4000000 {
+				label = "rootfs2";
+				reg = <0x04000000 0x04000000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial0_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&gmac0 {
+	qcom,forced_duplex = <1>;
+	qcom,forced_speed = <1000>;
+	qcom,phy_mdio_addr = <3>;
+	qcom,poll_required = <1>;
+	vlan_tag = <1 0x10>;
+};
+
+&gmac1 {
+	qcom,forced_duplex = <1>;
+	qcom,forced_speed = <1000>;
+	qcom,phy_mdio_addr = <4>;
+	qcom,poll_required = <1>;
+	vlan_tag = <2 0x20>;
+};
+
+&tlmm {
+	i2c0_pins: i2c0_pinmux {
+		mux_i2c {
+			function = "blsp_i2c0";
+			pins = "gpio58", "gpio59";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_mdio {
+			pins = "gpio53";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_mdc {
+			pins = "gpio52";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	serial0_pins: serial0_pinmux {
+		mux_uart {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi0_pins: spi0_pinmux {
+		mux_spi {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		mux_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio4";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+};
+
+&wifi1 {
+	status = "okay";
+};
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
new file mode 100644
index 0000000000..0c73539ee1
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
@@ -0,0 +1,347 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "ALFA Network AP120C-AC";
+	compatible = "alfa-network,ap120c-ac";
+
+	aliases {
+		led-boot = &status;
+		led-failsafe = &status;
+		led-running = &status;
+		led-upgrade = &status;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status: status {
+			label = "ap120c-ac:blue:status";
+			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		wan {
+			label = "ap120c-ac:amber:wan";
+			gpios = <&qca8075 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "ap120c-ac:green:wlan2g";
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "ap120c-ac:red:wlan5g";
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+
+			pinctrl-0 = <&mdio_pins>;
+			pinctrl-names = "default";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		counter@4a1000 {
+			compatible = "qcom,qca-gcnt";
+			reg = <0x4a1000 0x4>;
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		usb2@60f8800 {
+			status = "okay";
+		};
+
+		usb3@8af8800 {
+			status = "okay";
+
+			dwc3@8a00000 {
+				phys = <&usb3_hs_phy>;
+				phy-names = "usb2-phy";
+			};
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		qca8075: ess-switch@c000000 {
+			status = "okay";
+
+			switch_lan_bmp = <0x10>;
+			switch_wan_bmp = <0x20>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	tpm@29 {
+		compatible = "atmel,at97sc3204t";
+		reg = <0x29>;
+	};
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
+		   <&tlmm  4 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+			};
+
+			partition@f0000 {
+				label = "APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "priv_data1";
+				reg = <0x00180000 0x00010000>;
+				read-only;
+			};
+
+			partition@190000 {
+				label = "priv_data2";
+				reg = <0x00190000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+
+	nand@1 {
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "rootfs1";
+				reg = <0x00000000 0x04000000>;
+			};
+
+			partition@4000000 {
+				label = "rootfs2";
+				reg = <0x04000000 0x04000000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial0_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&gmac0 {
+	qcom,forced_duplex = <1>;
+	qcom,forced_speed = <1000>;
+	qcom,phy_mdio_addr = <3>;
+	qcom,poll_required = <1>;
+	vlan_tag = <1 0x10>;
+};
+
+&gmac1 {
+	qcom,forced_duplex = <1>;
+	qcom,forced_speed = <1000>;
+	qcom,phy_mdio_addr = <4>;
+	qcom,poll_required = <1>;
+	vlan_tag = <2 0x20>;
+};
+
+&tlmm {
+	i2c0_pins: i2c0_pinmux {
+		mux_i2c {
+			function = "blsp_i2c0";
+			pins = "gpio58", "gpio59";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_mdio {
+			pins = "gpio53";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_mdc {
+			pins = "gpio52";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	serial0_pins: serial0_pinmux {
+		mux_uart {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi0_pins: spi0_pinmux {
+		mux_spi {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		mux_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio4";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+};
+
+&wifi1 {
+	status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 31468fd758..f7e7ba3d0f 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -62,6 +62,21 @@ define Device/8dev_jalapeno
 endef
 TARGET_DEVICES += 8dev_jalapeno
 
+define Device/alfa-network_ap120c-ac
+	$(call Device/FitImage)
+	$(call Device/UbiFit)
+	DEVICE_TITLE := ALFA Network AP120C-AC
+	DEVICE_DTS := qcom-ipq4018-ap120c-ac
+	DEVICE_PACKAGES := ipq-wifi-alfa-network_ap120c-ac kmod-usb-acm \
+		kmod-tpm-i2c-atmel uboot-envtools
+	BLOCKSIZE := 128k
+	PAGESIZE := 2048
+	IMAGE_SIZE := 65536k
+	IMAGES := nand-factory.bin nand-sysupgrade.bin
+	IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+endef
+TARGET_DEVICES += alfa-network_ap120c-ac
+
 define Device/asus_map-ac2200
 	$(call Device/FitImageLzma)
 	DEVICE_DTS := qcom-ipq4019-map-ac2200
diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
index 20ea3a8449..551ac6f109 100644
--- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
@@ -10,11 +10,12 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,23 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
 +	qcom-ipq4018-a42.dtb \
++	qcom-ipq4018-ap120c-ac.dtb \
 +	qcom-ipq4018-ea6350v3.dtb \
 +	qcom-ipq4018-eap1300.dtb \
 +	qcom-ipq4018-ex6100v2.dtb \
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index f3472b32c0..0e27eeab65 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,11 +10,12 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
 +	qcom-ipq4018-a42.dtb \
++	qcom-ipq4018-ap120c-ac.dtb \
 +	qcom-ipq4018-ea6350v3.dtb \
 +	qcom-ipq4018-eap1300.dtb \
 +	qcom-ipq4018-ex6100v2.dtb \