aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorSander Vanheule <sander@svanheule.net>2022-07-28 15:13:52 +0200
committerSander Vanheule <sander@svanheule.net>2022-07-28 15:17:04 +0200
commita63aeaecf1f3387df020854c9b22a365207399ce (patch)
treeef6c7197c70e8c5c6847af25ff282da71f322527 /target/linux
parentf2f09bc00280f5bd60b36d525a5e229550958b6d (diff)
downloadupstream-a63aeaecf1f3387df020854c9b22a365207399ce.tar.gz
upstream-a63aeaecf1f3387df020854c9b22a365207399ce.tar.bz2
upstream-a63aeaecf1f3387df020854c9b22a365207399ce.zip
realtek: remove support for HPE 1920 series
Support for HPE 1920 images depends on two non-existent tools (mkh3cimg and mkh3cvfs) from the in the firmware-utils package. Revert commit f2f09bc00280 ("realtek: add support for HPE 1920 series") until support for these tools is merged and made available in OpenWrt. Signed-off-by: Sander Vanheule <sander@svanheule.net>
Diffstat (limited to 'target/linux')
-rw-r--r--target/linux/realtek/base-files/etc/board.d/02_network18
-rw-r--r--target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts113
-rw-r--r--target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts48
-rw-r--r--target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts68
-rw-r--r--target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi117
-rw-r--r--target/linux/realtek/dts-5.10/rtl838x.dtsi7
-rw-r--r--target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi96
-rw-r--r--target/linux/realtek/image/Makefile49
-rw-r--r--target/linux/realtek/image/rtl838x.mk24
-rw-r--r--target/linux/realtek/rtl838x/config-5.103
10 files changed, 3 insertions, 540 deletions
diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index 5356bcac65..af9db848dd 100644
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -22,20 +22,9 @@ ucidef_set_bridge_device switch
ucidef_set_interface_lan "$lan_list"
lan_mac=""
-lan_mac_start=""
lan_mac_end=""
label_mac=""
case $board in
-hpe,1920-8g|\
-hpe,1920-16g|\
-hpe,1920-24g)
- label_mac=$(mtd_get_mac_binary factory 0x68)
- lan_mac=$label_mac
- mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
- mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
- lan_mac_start=$(macaddr_add $lan_mac 2)
- lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1)))
- ;;
*)
lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start)
lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end)
@@ -47,11 +36,10 @@ esac
ucidef_set_interface_macaddr "lan" $lan_mac
ucidef_set_bridge_mac "$lan_mac"
ucidef_set_network_device_mac eth0 $lan_mac
-[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac
for lan in $lan_list; do
- ucidef_set_network_device_mac $lan $lan_mac_start
- [ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start)
- lan_mac_start=$(macaddr_add $lan_mac_start 1)
+ ucidef_set_network_device_mac $lan $lan_mac
+ [ -z "$lan_mac_end" ] || [ "$lan_mac" == "$lan_mac_end" ] && lan_mac=$(macaddr_setbit_la $lan_mac)
+ lan_mac=$(macaddr_add $lan_mac 1)
done
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
diff --git a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
deleted file mode 100644
index b51c75f355..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
+++ /dev/null
@@ -1,113 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl838x.dtsi"
-#include "rtl838x_hpe_1920.dtsi"
-
-/ {
- compatible = "hpe,1920-8g", "realtek,rtl838x-soc";
- model = "HPE 1920-8G (JG920A)";
-
- gpio1: rtl8231-gpio {
- compatible = "realtek,rtl8231-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- indirect-access-bus-id = <0>;
- };
-
- i2c0: i2c-gpio-0 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- sfp0: sfp-0 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c0>;
- los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
- // tx-fault and tx-disable unconnected
- };
-
- i2c1: i2c-gpio-1 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- sfp1: sfp-1 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c1>;
- los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
- // tx-fault and tx-disable unconnected
- };
-};
-
-&ethernet0 {
- mdio: mdio-bus {
- compatible = "realtek,rtl838x-mdio";
- regmap = <&ethernet0>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- INTERNAL_PHY(8)
- INTERNAL_PHY(9)
- INTERNAL_PHY(10)
- INTERNAL_PHY(11)
- INTERNAL_PHY(12)
- INTERNAL_PHY(13)
- INTERNAL_PHY(14)
- INTERNAL_PHY(15)
-
- INTERNAL_PHY(24)
- INTERNAL_PHY(26)
- };
-};
-
-&switch0 {
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- SWITCH_PORT(8, 1, internal)
- SWITCH_PORT(9, 2, internal)
- SWITCH_PORT(10, 3, internal)
- SWITCH_PORT(11, 4, internal)
- SWITCH_PORT(12, 5, internal)
- SWITCH_PORT(13, 6, internal)
- SWITCH_PORT(14, 7, internal)
- SWITCH_PORT(15, 8, internal)
-
- port@24 {
- reg = <24>;
- label = "lan9";
- phy-mode = "1000base-x";
- managed = "in-band-status";
- sfp = <&sfp0>;
- };
-
- port@26 {
- reg = <26>;
- label = "lan10";
- phy-mode = "1000base-x";
- managed = "in-band-status";
- sfp = <&sfp1>;
- };
-
- port@28 {
- ethernet = <&ethernet0>;
- reg = <28>;
- phy-mode = "internal";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
deleted file mode 100644
index 59043b2f6f..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl8382_hpe_1920.dtsi"
-
-/ {
- compatible = "hpe,1920-16g", "realtek,rtl838x-soc";
- model = "HPE 1920-16G (JG923A)";
-};
-
-&switch0 {
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- SWITCH_PORT(8, 1, internal)
- SWITCH_PORT(9, 2, internal)
- SWITCH_PORT(10, 3, internal)
- SWITCH_PORT(11, 4, internal)
- SWITCH_PORT(12, 5, internal)
- SWITCH_PORT(13, 6, internal)
- SWITCH_PORT(14, 7, internal)
- SWITCH_PORT(15, 8, internal)
-
- SWITCH_PORT(16, 9, qsgmii)
- SWITCH_PORT(17, 10, qsgmii)
- SWITCH_PORT(18, 11, qsgmii)
- SWITCH_PORT(19, 12, qsgmii)
- SWITCH_PORT(20, 13, qsgmii)
- SWITCH_PORT(21, 14, qsgmii)
- SWITCH_PORT(22, 15, qsgmii)
- SWITCH_PORT(23, 16, qsgmii)
-
- SWITCH_PORT(24, 17, qsgmii)
- SWITCH_PORT(25, 18, qsgmii)
- SWITCH_PORT(26, 19, qsgmii)
- SWITCH_PORT(27, 20, qsgmii)
-
- port@28 {
- ethernet = <&ethernet0>;
- reg = <28>;
- phy-mode = "internal";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
deleted file mode 100644
index 61781c708e..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
+++ /dev/null
@@ -1,68 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl8382_hpe_1920.dtsi"
-
-/ {
- compatible = "hpe,1920-24g", "realtek,rtl838x-soc";
- model = "HPE 1920-24G (JG924A)";
-};
-
-&mdio {
- EXTERNAL_PHY(0)
- EXTERNAL_PHY(1)
- EXTERNAL_PHY(2)
- EXTERNAL_PHY(3)
- EXTERNAL_PHY(4)
- EXTERNAL_PHY(5)
- EXTERNAL_PHY(6)
- EXTERNAL_PHY(7)
-};
-
-&switch0 {
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- SWITCH_PORT(0, 1, qsgmii)
- SWITCH_PORT(1, 2, qsgmii)
- SWITCH_PORT(2, 3, qsgmii)
- SWITCH_PORT(3, 4, qsgmii)
- SWITCH_PORT(4, 5, qsgmii)
- SWITCH_PORT(5, 6, qsgmii)
- SWITCH_PORT(6, 7, qsgmii)
- SWITCH_PORT(7, 8, qsgmii)
-
- SWITCH_PORT(8, 9, internal)
- SWITCH_PORT(9, 10, internal)
- SWITCH_PORT(10, 11, internal)
- SWITCH_PORT(11, 12, internal)
- SWITCH_PORT(12, 13, internal)
- SWITCH_PORT(13, 14, internal)
- SWITCH_PORT(14, 15, internal)
- SWITCH_PORT(15, 16, internal)
-
- SWITCH_PORT(16, 17, qsgmii)
- SWITCH_PORT(17, 18, qsgmii)
- SWITCH_PORT(18, 19, qsgmii)
- SWITCH_PORT(19, 20, qsgmii)
- SWITCH_PORT(20, 21, qsgmii)
- SWITCH_PORT(21, 22, qsgmii)
- SWITCH_PORT(22, 23, qsgmii)
- SWITCH_PORT(23, 24, qsgmii)
-
- SWITCH_PORT(24, 25, qsgmii)
- SWITCH_PORT(25, 26, qsgmii)
- SWITCH_PORT(26, 27, qsgmii)
- SWITCH_PORT(27, 28, qsgmii)
-
- port@28 {
- ethernet = <&ethernet0>;
- reg = <28>;
- phy-mode = "internal";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
deleted file mode 100644
index 5368b41c27..0000000000
--- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
+++ /dev/null
@@ -1,117 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "rtl838x.dtsi"
-#include "rtl838x_hpe_1920.dtsi"
-
-/ {
- gpio1: rtl8231-gpio {
- compatible = "realtek,rtl8231-gpio";
- #gpio-cells = <2>;
- gpio-controller;
- indirect-access-bus-id = <0>;
- };
-
- i2c0: i2c-gpio-0 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- sfp0: sfp-0 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c0>;
- los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
- // tx-fault unconnected
- // tx-disable connected to RTL8214FC
- };
-
- i2c1: i2c-gpio-1 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- sfp1: sfp-1 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c1>;
- los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
- // tx-fault unconnected
- // tx-disable connected to RTL8214FC
- };
-
- i2c2: i2c-gpio-2 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio1 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- sfp2: sfp-2 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c2>;
- los-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
- // tx-fault unconnected
- // tx-disable connected to RTL8214FC
- };
-
- i2c3: i2c-gpio-3 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio1 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- i2c-gpio,delay-us = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- sfp3: sfp-3 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c3>;
- los-gpio = <&gpio1 34 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpio1 33 GPIO_ACTIVE_LOW>;
- // tx-fault unconnected
- // tx-disable connected to RTL8214FC
- };
-};
-
-&ethernet0 {
- mdio: mdio-bus {
- compatible = "realtek,rtl838x-mdio";
- regmap = <&ethernet0>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- INTERNAL_PHY(8)
- INTERNAL_PHY(9)
- INTERNAL_PHY(10)
- INTERNAL_PHY(11)
- INTERNAL_PHY(12)
- INTERNAL_PHY(13)
- INTERNAL_PHY(14)
- INTERNAL_PHY(15)
-
- EXTERNAL_PHY(16)
- EXTERNAL_PHY(17)
- EXTERNAL_PHY(18)
- EXTERNAL_PHY(19)
- EXTERNAL_PHY(20)
- EXTERNAL_PHY(21)
- EXTERNAL_PHY(22)
- EXTERNAL_PHY(23)
-
- EXTERNAL_SFP_PHY_FULL(24, 0)
- EXTERNAL_SFP_PHY_FULL(25, 1)
- EXTERNAL_SFP_PHY_FULL(26, 2)
- EXTERNAL_SFP_PHY_FULL(27, 3)
- };
-};
diff --git a/target/linux/realtek/dts-5.10/rtl838x.dtsi b/target/linux/realtek/dts-5.10/rtl838x.dtsi
index 41fdbdae20..11cabc3f63 100644
--- a/target/linux/realtek/dts-5.10/rtl838x.dtsi
+++ b/target/linux/realtek/dts-5.10/rtl838x.dtsi
@@ -27,13 +27,6 @@
reg = <##n>; \
};
-#define EXTERNAL_SFP_PHY_FULL(n, s) \
- phy##n: ethernet-phy@##n { \
- compatible = "ethernet-phy-ieee802.3-c22"; \
- sfp = <&sfp##s>; \
- reg = <##n>; \
- };
-
#define SWITCH_PORT(n, s, m) \
port@##n { \
reg = <##n>; \
diff --git a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
deleted file mode 100644
index 8e29af62bb..0000000000
--- a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
+++ /dev/null
@@ -1,96 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- chosen {
- bootargs = "console=ttyS0,38400";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x8000000>;
- };
-
- watchdog1: watchdog {
- // PT7A7514
- compatible = "linux,wdt-gpio";
- gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
- hw_algo = "toggle";
- hw_margin_ms = <1000>;
- always-running;
-
- pinctrl-names = "default";
- pinctrl-0 = <&pinmux_disable_sys_led>;
- };
-};
-
-&watchdog0 {
- status = "disabled";
-};
-
-&spi0 {
- status = "okay";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <50000000>;
- m25p,fast-read;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "bootware_basic";
- reg = <0x0 0x50000>;
- read-only;
- };
-
- partition@0x60000 {
- label = "bootware_data";
- reg = <0x60000 0x30000>;
- read-only;
- };
-
- partition@0x90000 {
- label = "bootware_extend";
- reg = <0x90000 0x40000>;
- read-only;
- };
-
- partition@0x100000 {
- label = "bootware_basic_backup";
- reg = <0x100000 0x50000>;
- read-only;
- };
-
- partition@0x160000 {
- label = "bootware_data_backup";
- reg = <0x160000 0x30000>;
- read-only;
- };
-
- partition@0x190000 {
- label = "bootware_extend_backup";
- reg = <0x190000 0x40000>;
- read-only;
- };
-
- partition@0x300000 {
- label = "firmware";
- compatible = "h3c,vfs-firmware";
- reg = <0x300000 0x1cf0000>;
- };
-
- partition@0x1ff0000 {
- label = "factory";
- reg = <0x1ff0000 0x10000>;
- read-only;
- };
- };
- };
-};
diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile
index 6165d99bfc..cf779002e8 100644
--- a/target/linux/realtek/image/Makefile
+++ b/target/linux/realtek/image/Makefile
@@ -8,7 +8,6 @@ KERNEL_ENTRY = 0x80000400
DEVICE_VARS += ZYXEL_VERS DLINK_KERNEL_PART_SIZE
DEVICE_VARS += CAMEO_KERNEL_PART CAMEO_ROOTFS_PART CAMEO_CUSTOMER_SIGNATURE CAMEO_BOARD_VERSION
-DEVICE_VARS += H3C_PRODUCT_ID H3C_DEVICE_ID
define Build/zyxel-vers
( echo VERS;\
@@ -42,43 +41,6 @@ define Build/dlink-headers
cat $@.kernel_part.hex $@.rootfs_part.hex > $@
endef
-define Build/7z
- $(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@)
- mv $@.new $@
-endef
-
-define Build/h3c-image
- $(STAGING_DIR_HOST)/bin/mkh3cimg \
- -i $(@) \
- -o $(@).new \
- -c 7z \
- -p $(H3C_PRODUCT_ID) \
- -d $(H3C_DEVICE_ID)
- mv $@.new $@
-endef
-
-define Build/h3c-vfs
- $(STAGING_DIR_HOST)/bin/mkh3cvfs \
- -i $(@) \
- -o $(@).new \
- -f openwrt-kernel.bin
- mv $@.new $@
-endef
-
-define Build/relocate-kernel
- rm -rf $@.relocate
- $(CP) ../../generic/image/relocate $@.relocate
- $(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) LZMA_TEXT_START=0x82000000 \
- CROSS_COMPILE=$(TARGET_CROSS)
- ( \
- dd if=$@.relocate/loader.bin bs=32 conv=sync && \
- perl -e '@s = stat("$@"); print pack("N", @s[7])' && \
- cat "$@" \
- ) > "$@.new"
- mv "$@.new" "$@"
- rm -rf $@.relocate
-endef
-
define Device/Default
PROFILES = Default
KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
@@ -90,17 +52,6 @@ define Device/Default
check-size | append-metadata
endef
-define Device/hpe_1920
- DEVICE_VENDOR := HPE
- IMAGE_SIZE := 29632k
- BLOCKSIZE := 64k
- H3C_PRODUCT_ID := 0x3c010501
- KERNEL := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image | h3c-vfs
- KERNEL_INITRAMFS := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image
- IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
- pad-rootfs | check-size | append-metadata
-endef
-
# "NGE" refers to the uImage magic
define Device/netgear_nge
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma
diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index 60eda5359d..887f82e385 100644
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -65,30 +65,6 @@ define Device/engenius_ews2910p
endef
TARGET_DEVICES += engenius_ews2910p
-define Device/hpe_1920-8g
- $(Device/hpe_1920)
- SOC := rtl8380
- DEVICE_MODEL := 1920-8G (JG920A)
- H3C_DEVICE_ID := 0x00010023
-endef
-TARGET_DEVICES += hpe_1920-8g
-
-define Device/hpe_1920-16g
- $(Device/hpe_1920)
- SOC := rtl8382
- DEVICE_MODEL := 1920-16G (JG923A)
- H3C_DEVICE_ID := 0x00010026
-endef
-TARGET_DEVICES += hpe_1920-16g
-
-define Device/hpe_1920-24g
- $(Device/hpe_1920)
- SOC := rtl8382
- DEVICE_MODEL := 1920-24G (JG924A)
- H3C_DEVICE_ID := 0x00010027
-endef
-TARGET_DEVICES += hpe_1920-24g
-
define Device/inaba_aml2-17gp
SOC := rtl8382
IMAGE_SIZE := 13504k
diff --git a/target/linux/realtek/rtl838x/config-5.10 b/target/linux/realtek/rtl838x/config-5.10
index 9075aa6d3c..c117fc489a 100644
--- a/target/linux/realtek/rtl838x/config-5.10
+++ b/target/linux/realtek/rtl838x/config-5.10
@@ -74,8 +74,6 @@ CONFIG_GPIO_PCA953X=y
CONFIG_GPIO_PCA953X_IRQ=y
CONFIG_GPIO_REALTEK_OTTO=y
CONFIG_GPIO_RTL8231=y
-CONFIG_GPIO_WATCHDOG=y
-# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
CONFIG_GRO_CELLS=y
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDWARE_WATCHPOINTS=y
@@ -136,7 +134,6 @@ CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_BRNIMAGE_FW=y
CONFIG_MTD_SPLIT_EVA_FW=y
CONFIG_MTD_SPLIT_FIRMWARE=y
-CONFIG_MTD_SPLIT_H3C_VFS=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_NEED_DMA_MAP_STATE=y